Installation instructions 2 Guide rail

Transcription

1 Set sliding door fittings ntra I ttention Installation instructions uide rail 3 Door stoppers 4 Trolley complete 5 Wall fixtures 5/6"-8U Screw on Screw on Screw on oosen / Tighten Install t right angle Drill Sliding door fittings ntra I for wooden doors ( 3/4" thickness ) (without screws and dowels, at construction site) not included in scope of delivery. 6 Special tool SW 5 Dowels djust Set evel You must check the position of the wall fixtures and the door stopper before installation! 7 ottom guide Perpendicular easure ark Visual inspection Warning! Proper header or mounting beam must be installed the full length of the sliding door rail to provide adequate support for sliding door system weight of door! (without dowels and screws, at construction site) Specialtool Set ntra I rt. o. Set / ach USU47-800D USU47-00D USU47-300D USU47-540D eyerle US..., P-eyerle, it s subsidiaries and agents are not responsible or liable for damage or injury to any persons or property due to improper installation of it s products. ll liabilities reside solely with the installer. omply with all general safety regulations when installing the sliding door fittings! Installation to be completed by qualified licensed contractor. e sure to tighten all screw connections one week after starting to use the sliding door fittings! ever use scouring agents to clean the sliding door fittings; rather use commercially available stainlesssteel cleaners! people required easure larify questions See instructions Secure omplete-sets Set ntra I rt. o. wooden door 3/4" 0 lbs ottom guide D ach D USU47-800D 70 7/8" 30 5/6" 3 9 /" /6" 98 7/6" /4" - 3/8" 3/8" 99 /8" ( = - + ) USU47-00D 8 /6" 4 /8" /6" /8" 98 7/6" /4" - 3/8" 3/8" 99 /8" eyerle US ogan ircle W, tlanta, 3038 Phone (404) , ax (404) , USU47_ont_US USU47-300D 90 9/6" 6 3/4" /4" - 44 /6" 98 7/6" /4" - 3/8" 3/8" 99 /8" USU47-540D 00" 9 5/6" 4 44 /" /6" 98 7/6" /4" - 3/8" 3/8" 99 /8" Right to make technical changes reserved - Dimensions in - Version 0.0

2 Installation to be completed by qualified licensed contractor. ig. 3 ig. 4,5,6 = 7 ig. ig. ig. 3 ig. 4 ig. 5 ig. 6 0 lbs lbs 3/4" 5/6"-8U " " 5/6"-8U ig. 7 ig. 8 ig. 9 ig. 0 ig. ig. 3 ig. 4 3 ig. 3 ig. 4 ig. 5 ig. 6 ig. 7 ig. 8 /8" 3 ig. 9 Right to make technical changes reserved - Dimensions in - Version 0.0 ig. 0 ig. ig. Installation instructions Sliding door fittings ntra I for wooden doors ( m ax. 3/4" thickness ) ig. 3

3 Planning guide Sliding door fittings ntra I for wooden doors ( 3/4" thickness ) You must check the position of the wall fixtures and the door stopper before installation! Warning! Proper header or mounting beam must be installed the full length of the sliding door rail to provide adequate support for sliding door system weight of door! wooden door 3/4" 0 lbs ottom guide D Set ntra I rt. o. USU47-800D USU47-00D USU47-300D USU47-540D Right to make technical changes reserved - Dimensions in - Version Page of 6

4 Sliding door fittings ntra I for wooden doors ( 3/4" thickness ) - wooden door ach anufacturing dimensions (special model) D D 98 7/6" /4" - 3/8" kg oad-bearing capacity of 99 /8" the guide rail ( = - + Y ) J ach ( 3/8 ) 8 /8" Z ( ) 30" 30" Y ( 3/8" ) J = uide-rail length = Drill hole clearance = Wall fixture D = Passage width D = Door width = Passage height = Door floor clearance = astening clearance = Door height J = oad-bearing capacity of the guide rail = ottom guide = Door stopper = Trolley = Door knob clearance Y = Door height overhang Z = uide-rail overhang ( ) = recommended! 98 7/6" ( ) wooden door 3/4" 0 lbs D 99 /8" ( ) Warning! Proper header or mounting beam must be installed the full length of the sliding door rail to provide adequate support for sliding door system weight of door! D = D + (") alculation for guide-rail length for door Passage width D uide-rail length Overhang Z ( ) ( uide-rail ) Door handle clearance Door width D Overhang Z + Passage width D + Door width D Door handle clearance = uide-rail length ake door handle clearance so that fingers do not get ped when the door is manipulated! See page 5. Right to make technical changes reserved - Dimensions in - Version Page of 6

5 Sliding door fittings ntra I for wooden doors ( 3/4" thickness ) - wooden doors ach D anufacturing dimensions (special model) 99 /8" /4" - D D 98 7/6" 3/8" ( = - + Y ) ( 3/8 ) kg oad-bearing capacity of the guide rail J ach K /8" K 4" 8 /8" 30" 30" Y ( 3/8") J = Total guide-rail length / = uide-rail length / = Drill hole clearance = Wall fixture D = Passage width D/D = Door width = Passage height = Door floor clearance = astening clearance = Door height J = oad-bearing capacity of the guide rail K = oupling = ottom guide = Door stopper = Trolley = Door knob clearance Y = Door height overhang 98 7/6" wooden door 3/4" 0 lbs ( 3/6" ( 5 ) ) wooden door 3/4" 0 lbs 99 /8 " Warning! Proper header or mounting beam must be installed the full length of the sliding door rail to provide adequate support for sliding door system weight of door! ( ) D 98 7/6" ( ) ( ) = recommended! D D alculation for total guide-rail length for doors Total guide-rail length Passage width D Door handle clearance Door width left D Door handle clearance Door width right D Door width D Door handle clearance + Passage width D + Door width D Door handle clearance = Total guide-rail length ake door handle clearance so that fingers do not get ped when the door is manipulated! See page 5. Right to make technical changes reserved - Dimensions in - Version Page 3 of 6

6 Sliding door fittings ntra I for wooden doors ( 3/4" thickness ) Wall fixture Standard installation Installation with baseboards and trim 5/6" 5/6" -8U 5/6" -8U ( 3/8" ) ( 3/8" ) 3/4" 3/4" 5/6" 5/6" /4" 3/6" 3/4" 3/4" ompensation disks /6", 3/6" and 3/8" To compensate for wall unevenness, order separately. ( Only piece per wall fixture! ) Spacers order separately. rt.-o. rt.-o. USO6-D /6" USO6-5D 3/6" USO6-33D 5/6" USO6-0D 3/8" Right to make technical changes reserved - Dimensions in - Version Page 4 of 6

7 Sliding door fittings ntra I for wooden doors ( 3/4" thickness ) Preparation of wooden door 3/4" Ø 7/3" ( 3/8" ) Y min. 4" 3/6" min. 4" ± /8" 3/6" djustable door height (longated holes in the trolley) Door height lock (rub screw) ± /8" min. 4" min. 4" 3/6" 55 3/6" /8" 98 7/6" Drill-hole dimension according to handle wooden door 3/4" 0 lbs 99 /8" 3/4" ( /4" - 3/8" ) inished floor ottom guide D 5 3/6" /6" ake door handle clearance so that fingers do not get ped when the door is manipulated! 5/6" Right to make technical changes reserved - Dimensions in - Version Page 5 of 6

8 Sliding door fittings ntra I for wooden doors ( 3/4" thickness ) Required system parts Please refer to the catalogue for article no s and models! uide rail Ø uide rail Ø for guide rail couplings Trolley complete 5/6"-8U Wall fixtures complete Without screws and dowels, at construction site ompensation disks /6", 3/6" and 3/8" order separately Door stoppers complete, stainless steel ottom guide, plastic ( Without screws and dowels, at construction site ) K uide rail coupling Ø SW 5 Special tool Right to make technical changes reserved - Dimensions in - Version Page 6 of 6