Alcoa Fastening Systems. Camloc Quick-Operating Fasteners

Size: px

Start display at page:

Download "Alcoa Fastening Systems. Camloc Quick-Operating Fasteners"

Raymond Neal
6 years ago
Views:

1 Camloc Quick-Operating Fasteners

2 Contents Page General Information... A-2 Important Information... A-3 - A-4 General Installation Instructions for 1/4-Turn Fasteners... A-5 1/4-Turn Fasteners 5F Series... B-1 - B-4 99F Series... C-1 - C-3 50F Series (900 N Tensile Strength)... D-1 - D-6 50F Series (3.700 N Tensile Strength)... E-1 - E / 2700 Series... F-1 - F Series... G-1 - G F Series... H-1 - H-5 One-Piece Fasteners V936F Series... I I F Series... J-1 - J-2 Push Button Fasteners 15F Series... K-1 - K-3 Push-Turn Fasteners 715F Series... L-1 - L-3 716F Series... M-1 - M-3 717F Series... N-1 - N-3 720F Series... O-1 - O-4 Pawl Latches V964L Series... P-1 - P-2 V965L Series... Q-1 - Q-2 Index Release February 2008 Alcoa A-1

3 General Information The Camloc brand was established in Since that time our fastening systems have been successfully integrated into numerous applications within many different industries. Each of our customers will feel the full benefit of our 70 years of fastening experience. Customer proximity, environmental awareness and quality are the main criteria of our services and products. ISO/TS 16949: 2002 DIN EN ISO : 2005 Please find additional information about our environmental program under: Your Alcoa team Disclaimer: Parts listed are subject to technical changes. All dimensions in mm. All information is correct to the best of our knowledge at the time of printing. No liability for disadvantages caused by printing errors or false application. Release February 2008 Alcoa A-2

4 Important Information on 1/4-Turn Fastener Advantages of the Camloc 1/4-Turn Fastener Safe mechanical quick release fastener systems Locking or unlocking by quarter turn Long life - high number of operating cycles Hand or tool-operated Service-friendly, time-saving and cost cutting Camloc fasteners are standardised worldwide Fastener series for any industrial applications Captive-type Tolerance compensating Vibration-resistant Components The 1/4-turn fastener consists of a stud, a retaining washer/ retaining ring and a cam receptacle. Depending upon the strength, fastener size and mounting conditions, the spring component is a part of the stud assembly or the receptacle. For some fastener series, stud assemblies with clip-in grommets are available which allow easy mounting without retaining washers. This ensures, at the same time, retention of the fastener. Stud Spring washers Retaining washer Cross pin Receptacle Release February 2008 Alcoa A-3

5 1/4-Turn Fasteners Important Information Design Principle Quarter-turn fasteners connect components under an elastic preload (frictional connection). Spring components to produce the preload may be part of the stud or receptacle. Forces: The fasteners transmit the tensile loads specified in the catalogue after overcoming the preload. Lateral forces are transmitted to the components by friction resulting from the preload of the fastener. Such forces vary with the conditions of the components. How it Operates When the stud assembly is rotated, the stud cross pin rides up the cam causing a controlled joint preload to be applied. This action is accomplished by rotating the stud 90. At this point a positive mechanical stop is reached and the cross pin falls into the locking detent. Excellent resistance to vibration induced loosening is assured. Stud Assembly Receptacle Cross pin Cross pin locking position Slope Unlocked Locked Cross pin locked in cam For general installation instructions please refer to the next page. Release February 2008 Alcoa A-4

6 1/4-Turn Fasteners General Installation Instructions Selecting the Fastener P = panel thickness (stud assembly) F = frame thickness (receptacle) G = P + F G = total thickness, consisting of P + F as well as possible gaskets, paint coats or gaps. This dimension gives the stud length number in the corresponding series tables. Installation Stud Stud With Grommet Stud For short, spring-loaded stud assemblies, the use of 4P3-1 pliers is recommended. Grommet With retaining washer (slotted) With retaining washer Magnetic head retaining Retaining washer Retaining washer Stud Stud washer mounting tool Retaining washer fitted Release February 2008 Alcoa A-5

7 5F Series Particular Features Max. tensile strength 670 N. Plastic washer stud assembly to protect decorative surfaces. Spring loaded receptacle. Selection Instructions 1. Select stud assembly and receptacle, page B-2 und B Select retaining washer or grommet, page B Select stud length number from total thickness G using the formula and table below, insert into stud part number * (e.g. V5S5-*AGV). With retaining washer G = P + F Determining the stud length number: With Grommet G = P + F + 1,4 Stud Length Table Total Thickness G Stud Length No. When Using Receptacles Other lengths on request. 0,50-0,90 1 0,90-1,30 2 1,30-1,65 3 1,65-2,05 4 2,05-2,40 5 2,40-2,80 6 2,80-3,20 7 3,20-3,55 8 3,55-3,95 9 3,95-4, ,30-4, ,70-5, ,10-5, ,45-5, ,85-6, ,20-6, ,60-7, ,00-7, ,35-7, ,75-8, ,15-8,50 21 Preferred dash-lengths Release February 2008 Alcoa B-1

8 5F Series Stud Assemblies Style Dimensions Materials / Finish C Part No. Slotted Recess Head with plastic washer (PA6) 120 V5S5- *AGV Steel / nickel-plated with plastic washer (PA6) 120 5S27-* S = 6,70 + (0,38 x length no.) Cross Recess Head with plastic washer (PA6) 120 V5S21- *AGV with stainless steel washer (tensile strength 470 N max.) 5S15-* S = 6,70 + (0,38 x length no.) * Length no. from Table, page B-1. For installation dimensions see page B-3. Release February 2008 Alcoa B-2

9 5F Series Stud Installation Instructions Installation Dimensions Retainig Washer Panel Thickness P up to 2,3 Accessories Retaining washer Material / Finish transparent passivated Panel Thickness P Part No. V5W3-1AG Retaining washer Installation: See page A-6 Panel thickness P over 2,3 Retaining washer 5S3-2 Retaining washer Installation: See page A-6 * For P up 1,4 : 5,6 for installation without retaining washer Snap-In Grommet Panel thickness P up to 2,9 Grommet Plastic (PA6) black to 1,4 5S72-5-1AA 1,8-2,9 5S72-9-1AA Grommet P max G min 1,4 2,0 2,9 3,5 Panel thickness P over 2,9 Grommet Release February 2008 Alcoa B-3

10 5F Series Receptacle Style Dimensions Materials / Finish C Part-No. Type 1 Rivet / Screw Mounting Steel / zinc flake coated V5R2-1AK7 5R2-3 Receptacle Installation Instructions Dimensions Rivet / Screw Mounting Release February 2008 Alcoa B-4

11 99F Series Particular Features Max. tensile strength 700 N. Increased grip range. Receptacles with external thread for screwing or retaining nut (see page C-3). Encapsulated design, splash-proof. Selection Instructions 1. Select stud assembly and receptacle, page C-2 and C Select hex nut for receptacle, if necessary, page C Select stud retaining washer, page C Select stud length number from total thickness G using the formula and table below, insert into stud part number * (e.g. 99S10-*A1). Determining the stud length number: Total Thickness G 0,5-1,5 1,5-3,0 30, - 4,5 4,5-6,0 6,0-7,5 7,5-9,0 9,0-10,5 10,5-12,0 12,0-13,5 13,5-15,0 Stud Length No Other lengths on request. Preferred dash-lengths Release February 2008 Alcoa C-1

12 99F Series Stud Assemblies Style Dimensions Materials / Finish C Part No. Slotted Recess Head 99S10-*A1 3,6 max when locked S = 15,5 + (0,76 x length no.) * Length no. from Table, see page C-1. Stud Installation Instructions Installation Dimensions Panel Thickness P 0,5-3,2 Accessories Retainig washer Materials / Finish Part No SW * For P up to 1,65 m 6,5 for installation without retaining washer Panel Thickness P over 3,2 Retaining washer Installation: See page A-6. Panel Thickness P 0,50-4,75 Retaining washer transparent passivated 99W10-01A1 V2600-LW-7 Retaining washer Installation: See page A-6. Mounting tool for Retainig washer V2600-LW-7 T98-1 Release February 2008 Alcoa C-2

13 99F Series Receptacles Style Dimensions Materials / Finish C Part No. Open Zinc die casting / zinc-plated, R10-01A1 Encapsulated Zinc die casting / zinc-plated, E10-01 Capsule: Receptacle Installation Instructions Installation Dimensions Accessories Materials / Finish Part No. Retaining nut Steel / zinc-plated, transparent passivated 99N10-01A1 Retaining nut Tap 15/32-32UNS-2B Release February 2008 Alcoa C-3

14 50F Series Particular Features Max. tensile strength 900 N. Plastic washer stud assembly to protect decorative surfaces. Spring loaded receptacle as snap-in and clip-on design. Snap-in grommet for quick stud installation without retaining washer. Selection Instructions 1. Select stud assembly and receptacle, page D-2 to D-4 and D Select retaining washer or grommet, page D Select stud length number from total thickness G using the formula and table below, insert into stud part number * (e.g. 50E21-*AGV). G = P G = P + 1,2 G = P + F G = P + F + 1,2 Stud Length Table Total Thickness G Stud Length No. when using Receptacles Type 1 F= 1,0-2,1 Total Thickness G Stud Length No. when using Receptacles Type 1 F= 2,1-3,0 Total Thickness G Stud Length No. when using Receptacles Type 2 0,50-1,10 1,10-1,70 1,70-2,30 2,30-2,90 2,90-3,50 3,50-4,10 4,10-4,70 4,70-5,30 5,30-5,90 5,90-6,50 6,50-7,10 7,10-7,70 7,70-8,30 8,30-8,90 8,90-9,50 9,50-10,10 10,10-10,70 10,70-11,30 11,30-11,90 11,90-12,50 12,50-13,10 13,10-13,70 13,70-14,30 14,30-14,90 14,90-15,50 15,50-16, ,50-1,10 1,10-1,70 1,70-2,30 2,30-2,90 2,90-3,50 3,50-4,10 4,10-4,70 4,70-5,30 5,30-5,90 5,90-6,50 6,50-7,10 7,10-7,70 7,70-8,30 8,30-8,90 8,90-9,50 9,50-10,10 10,10-10,70 10,70-11,30 11,30-11,90 11,90-12,50 12,50-13,10 13,10-13,70 13,70-14,30 14,30-14,90 14,90-15,50 15,50-16, ,30-2,90 2,90-3,50 3,50-4,10 4,10-4,70 4,70-5,30 5,30-5,90 5,90-6,50 6,50-7,10 7,10-7,70 7,70-8,30 8,30-8,90 8,90-9,50 9,50-10,10 10,10-10,70 10,70-11,30 11,30-11,90 11,90-12,50 12,50-13,10 13,10-13,70 13,70-14,30 14,30-14,90 14,90-15,50 15,50-16,10 16,10-16,70 16,70-17,30 17,30-17, Other lengths on request. Preferred dash-lengths Release February 2008 Alcoa D-1

15 50F Series Stud Assemblies Style Dimensions Materials / Finish C Part No. Slotted Recess Head with plastic washer (PA6) 80 50E21-*AGV Plastic washer (PA6) with plastic washer (PA6) 80 50E21-*S S = 11,40 + (0,6 x length no.) Cross Recess Head Ø with plastic washer (PA6) 80 50E70-*AGV Plastic washer (PA6) Ø Hex Head Slotted Recess with plastic washer (PA6) 80 50E90-*AGV Plastic washer (PA6) * Length no. from Table, see page D-1. Release February 2008 Alcoa D-2

16 50F Series Stud Assemblies Style Dimensions Materials / Finish C Part No. Hex Recess Head Ø with plastic washer (PA6) 80 50E60-*AGV Plastic washer (PA6) Ø Fixed Wing Head with plastic washer (PA6) 80 50E21-*WAGV Plastic washer (PA6) Offset Fixed Wing Head with plastic washer (PA6) 80 50E21-*W0AGV Plastic washer (PA6) * Length no. from Table, see page D-1. Release February 2008 Alcoa D-3

17 50F Series Stud Assemblies Style Dimensions Materials / Finish C Part No. Folding Bail Handle with plastic washer (PA6) 80 50E18-*AGV plastic washer (PA6) Star Formed Head with plastic head and plastic washer (PA6) - 40 up to E80-*AGV plastic washer (PA6) with plastic head and plastic washer (PA6) - 40 up to E80-*CP Wing Head with plastic head and plastic washer (PA6) - 40 up to E82-*AGV plastic washer (PA6) with plastic head and plastic washer (PA6) - 40 up to E82-*CP * Length no. from Table, see page D-1. Release February 2008 Alcoa D-4

18 50F Series Stud Installation Instructions Style Dimensions Materials / Finish P Part No. Snap-In Grommet Grommet Plastic (PA6) / natural colour Working temperature: -40 C C Up to 1,60 1,70-2,80 50S12-0-1AA 50S12-1-1AA 2,90-4,00 50S12-2-1AA 4,10-5,30 50S12-3-1AA 5,40-6,65 50S12-4-1AA Grommet Retaining Washer Retaining washer 4002-SW-SS Retaining washer 50E2-3BP Retaining washer Installation: see page A-6. Retaining washer Plastic (PA6) / natural colour 50W204-01K Working temperature: -40 C C ADVANTAGE: Plastic retaining washer to be assembled without tooling For P up to 2mm Ø 8 +0,2 for installation without retaining washer (see E-5) Release February 2008 Alcoa D-5

50F Series Receptacles Style Dimensions Materials / Finish Type 1 Snap-In

tensile strength 250 N Type 2 Clip-On Spring steel / zinc - flake coated F =

19 50F Series Receptacles Style Dimensions Materials / Finish Type 1 Snap-In Spring steel / zinc - flake coated Panel Thickness P F = 1,0-2,0 Part No. 170 Part No. 50E20-1AK7 Spring steel / zinc - flake coated F = 2,1-3, E20-2AK7 Max. tensile strength 250 N Type 2 Clip-On Spring steel / zinc - flake coated F = 0,8-5,6 170 V50R4-2-1AK7 Receptacle Installation Instructions Installation Dimensions Snap-In Clip-On clip in Release February 2008 Alcoa D-6

20 50F Series Particular Features Max. tensile strength N. Small-size fastener for high tensile load. Flat receptacle. High preload. Selection Instructions 1. Select stud assembly and receptacle, page E-2 to E-4 and E Select retaining washer, page E Select stud length number from total thickness G using the formula and table below, insert into stud part number * (e.g. 50E8-*AGV). G = P + F Stud Length Table Total Thickness G Stud Length No. Total Thickness G Stud Length No. 0,50-1,10 1,10-1, ,70-11,30 11,30-11, ,70-2,30 2,30-2,90 2,90-3,50 3,50-4,10 4,10-4,70 4,70-5,30 5,30-5,90 5,90-6,50 6,50-7,10 7,10-7,70 7,70-8,30 8,30-8,90 8,90-9,50 9,50-10,10 10,10-10, ,90-12,50 12,50-13,10 13,10-13,70 13,70-14,30 14,30-14,90 14,90-15,50 15,50-16,10 16,10-16,70 16,70-17,30 17,30-17,90 17,90-18,50 18,50-19,10 19,10-19,70 19,70-20,30 20,30-20, Other lengths on request. Preferred dash-lengths Release February 2008 Alcoa E-1

50F Series Stud Assemblies Style Dimensions Materials / Finish C Part No. Slotted Recess Head 50E8-*AGV max. 5,9 when locked 1) 50E8-*S Cross Recess Head 50E71-*AGV max.

21 50F Series Stud Assemblies Style Dimensions Materials / Finish C Part No. Slotted Recess Head 50E8-*AGV max. 5,9 when locked 1) 50E8-*S Cross Recess Head 50E71-*AGV max. 5,9 when locked Hex Head Slotted Recess 50E91-*AGV max. 10 when locked * Length no. from Table, page E-1. 1) Max. tensile strength N. Release February 2008 Alcoa E-2

22 50F Series Stud Assemblies Style Dimensions Materials / Finish C Part No. Hex Recess Head 50E61-*AGV max. 7,9 when locked Fixed Wing Head max. 16 when locked 50E8-*WAGV Offset Fixed Wing Head 50E8-*W0AGV max. 16 when locked * Length no. from Table, page E-1. Release February 2008 Alcoa E-3

knob -40 up to +60 50E81-*AGV max 29 when locked 1) with plastic knob -40 up to

locked 1) with plastic knob -40 up to +60 50E83-*CP Square Head 50E7-*AGV locked *

23 50F Series Stud Assemblies Style Dimensions Materials / Finish C Part No. Folding Bail Handle 38 max when locked 50E19-*AGV Star Formed Head with plastic knob -40 up to E81-*AGV max 29 when locked 1) with plastic knob -40 up to E81-*CP Wing Head with plastic knob -40 up to E83-*AGV max 29 when locked 1) with plastic knob -40 up to E83-*CP Square Head 50E7-*AGV locked * Length no. from Table, page E-1. 1) Max. tensile strength N. Release February 2008 Alcoa E-4

24 50F Series Stud Assemblies Installation Instructions Installation Dimensions Accessories Material / Finish Part No. Retaining washer (loose) 4002-SW-SS Retaining washer (fixed) 50E2-3BP Retaining washer Installation: see page A-6. Retaining washer (loose) Plastic (PA6) / natural colour 50W204-01K Working temperature: -40 C C For P up to 2 mm 8 + 0,2 for installation without retaining washer ADVANTAGE: Plastic retaining washer to be assembled without tooling. Release February 2008 Alcoa E-5

25 50F Series Stud Assemblies Style Dimensions Materials / Finish C Part No. Rivet- / Screw or Weld Mounting 3,3 6 max 1,5 Rivet / Screw Mounting V50R3-1-1AGV V50R3-1-1BP Welding Steel / zinc-plated V50R3-1-2AZ Version A Rivet/Screw Mounting Version B Welding Receptacle Installation Instructions Installation Dimensions Rivet- / Screw or Weld Mounting Release February 2008 Alcoa E-6

26 2600/2700 Series Particular Features Max. tensile strength N. Small-size fastener for high tensile load. Wide variety of conventional stud assembly and receptacle designs Series: Fillister head; 2700 Series: Flush head. Selection Instructions 1. Select stud assembly and receptacle, page F-3 up to F-5, F-7 up to F Select stud accessories (retaining washer, gasket), page F-6 and F Select hex nut for receptacle, if necessary, page F Select stud length number from total thickness G using the formula and table on page F-2 insert into stud part number * (e.g. V26S01-*AGV). Determining the stud length number when using receptacle: Type 1 + 3* G = P + F * For Type 3: G = 9,9 mm min. Type 2 G = P + F (0,75 min.) Type 4 G = P + X (0,5 min.) Release February 2008 Alcoa F-1

27 2600/2700 Series Stud Length Table Total Thickness G Stud Length No. When Using Type 1 Receptacles Total Thickness G Stud Length No. When Using Type Receptacles Total Thickness G Stud Length No. When Using Type 3 Receptacles 0,75-1,50 1,50-2,30 2,30-3,05 3,05-3,80 3,80-4,60 4,60-5,35 5,35-6,10 6,10-6,85 6,85-7,60 7,60-8,40 8,40-9,15 9,15-9,90 9,90-10,65 10,65-11,40 11,40-12,20 12,20-12,95 12,95-13,70 13,70-14,50 14,50-15,25 15,25-16,00 16,00-16,75 16,75-17,50 17,50-18,30 18,30-19,05 19,05-19,80 19,80-20,60 20,60-21,35 21,35-22,10 22,10-22,85 22,85-23,60 23,60-24,40 24,40-25,15 25,15-25,90 25,90-26,65 26,65-27,40 27,40-28,20 28,20-28,95 28,95-29,70 29,70-30,50 30,50-31, ,75-1,50 1,50-2,30 2,30-3,05 3,05-3,80 3,80-4,60 4,60-5,35 5,35-6,10 6,10-6,85 6,85-7,60 7,60-8,40 8,40-9,15 9,15-9,90 9,90-10,65 10,65-11,40 11,40-12,20 12,20-12,95 12,95-13,70 13,70-14,50 14,50-15,25 15,25-16,00 16,00-16,75 16,75-17,50 17,50-18,30 18,30-19,05 19,05-19,80 19,80-20,60 20,60-21,35 21,35-22,10 22,10-22,85 22,85-23,60 23,60-24,40 24,40-25,15 25,15-25,90 25,90-26,65 26,65-27,40 27,40-28,20 28,20-28,95 28,95-29,70 29,70-30, ,90-10,65 10,65-11,40 11,40-12,20 12,20-12,95 12,95-13,70 13,70-14,50 14,50-15,25 15,25-16,00 16,00-16,75 16,75-17,50 17,50-18,30 18,30-19,05 19,05-19,80 19,80-20,60 20,60-21,35 21,35-22,10 22,10-22,85 22,85-23,60 23,60-24,40 24,40-25,15 25,15-25,90 25,90-26,65 26,65-27,40 27,40-28,20 28,20-28,95 28,95-29,70 29,70-30,50 30,50-31,25 31,25-32,00 32,00-32,75 32,75-33,50 33,50-34,30 34,30-35,05 35,05-35,80 35,80-36,60 36,60-37,35 37,35-38,10 38,10-38,85 38,85-39,60 39,60-40, Other lengths on request. Preferred dash-lengths Release February 2008 Alcoa F-2

2600 Series Stud Assemblies Style Dimensions Materials / Finish C Part No.

1) 2600-*S Steel / nickel-plated 26S42-* Cross Recess Fillister Head (Phillips Gr.

Steel / chrome-plated 26S34-* max 16,8 when locked Fixed Wing Head max 15,2 when locked

28 2600 Series Stud Assemblies Style Dimensions Materials / Finish C Part No. Slotted Recess Fillister Head V26S01-*AGV max 5,2 when locked Steel / chrome-plated 26S38-* 1) 2600-*S Steel / nickel-plated 26S42-* Cross Recess Fillister Head (Phillips Gr.2) V26S02-*AGV max 5,2 when locked Steel / nickel-plated 26S39-* 1) 26S51-* Knurled Head Steel / chrome-plated 26S34-* max 16,8 when locked Fixed Wing Head max 15,2 when locked V26S04-*AGV 1) 2600-*SW * Length no. from Table, page F-2. 1) Max. Tensile strength N. Release February 2008 Alcoa F-3

29 2600 Series Stud Assemblies Style Dimensions Materials / Finish C Part No. Star Formed Head Ref 20 with plastic knob (PA6) -40 up to +60 V26S06- *AGV max Ø 13 S Ø 6,3 8 Ø 3,2 Note: Not to be used with encapsulated receptacles Ref Ø 28 Wing Head max 17,5 with plastic knob (PA6) -40 up to +60 V26S07- *AGV max Ø 13 S Ø 6,3 8 Ø 3,2 Note: Not to be used with encapsulated receptacles Ref 26 Ref 11 Triangular Head Ref 16 max Ø 13 with plastic knob (PA6) -40 up to +60 V26S08- *AGV S Ø 6,3 8 Ø 3,2 Note: Not to be used with encapsulated receptacles Ref Ø 30 * Length no. from Table, page F-2. Release February 2008 Alcoa F-4

30 2700 Series Stud Assemblies Style Dimensions Materials / Finish C Part No. Slotted Recess Flush Head V27S01-*AGV 2700-*S 1) Cross Recess Flush Head V27S02-*AGV * Length no. from Table, page F-2. 1) Max. Tensile strength N. Release February 2008 Alcoa F-5

31 2600 Series Stud Installation Instructions Installation Dimensions Accessories Material / Finish Part No. Stud Without Retaining Washer, Retention Type - - Note: Dash 4 stud and smaller are selfcaptivating - 4P3-1 installation pliers, see page F-7. Stud Without Retaining Washer, Floating Type Retaining washer Note: Retaining rings are required for stud length dash numbers 5 and up 2600-SW Retaining washer 4P3-1 installation pliers, see page F-7. Stud With Retaining Washer, Fixed Spring Cup Retaining washer Not for chromeplated parts V2600-LW-7 Retaining washer 4P3-1 installation pliers, see page F-7. Sealed AN 6227 B3 gasket Gaskets Rubber (100 C) AN6227-B6 AN 6227 B6 gasket Rubber (100 C) AN6227-B3 Retaining washer T98-1 installation tool, page F-6. Installation see page A-6. 4P3-1 installation pliers, see page F-7. Release February 2008 Alcoa F-6

32 2700 Series Stud Installation Instructions Installation Dimensions Accessories Material / Finish Part No. Stud Without Retaining Washer, Retention Type - - Note: Dash 4 stud and smaller are selfcaptivating - * P = 0,5-3,2 Installation tool see below Stud Without Retaining Washer, Floating Type Retaining washer Note: Retaining rings are required for stud length dash numbers 5 and up 2600-SW Installation: see page A-6 Retaining washer Installation tool see below Stud Without Retaining Washer, Fixed Spring Cup Retaining washer V2600-LW-7 Steel / nickel-plated V27W01-1AN Retaining washer Installation: see page A-6 Installation tool see below Stud Installation pliers 4P3-1 V2600-LW-7 retaining washer installation tool T98-1 Release February 2008 Alcoa F-7

33 2600/2700 Series Receptacles Style Dimensions Materials / Finish D C Part No. Type 1 Swage transparent passivated 2,6 V26R6-1AGV Type 1 Cast Hard bronze / zinc-plated, transparent passivated 2,5 V FGV Hard bronze / zinc-plated, transparent passivated 3,3 V FGV 2, S Type 1 Narrow Width Hard bronze / zinc-plated, transparent passivated 2,5 V212-12N-1FGV Type 1 Encapsulated Hard bronze / zinc-plated, transparent passivated 2, R16-1FGV Capsule: 2, R18-1-1AA Release February 2008 Alcoa F-8

34 2600/2700 Series Receptacles Style Dimensions Materials / Finish C Part No. Type 2 Side Mounting Aluminium / anodized R1-1 Type 3 Rivet / Screw or Weld Mounting Rivet / Screw Mounting V312-12AGV Weld nib S Welding WS Release February 2008 Alcoa F-9

35 2600/2700 Series Receptacles Style Dimensions Materials / Finish C Part No. Type 4 Single Hole Mounting Zinc die cast / zinc-plated, clear chromate R10-01A1 Type 4 Single Hole Mounting Encapsulated Zinc die cast / zinc-plated, clear chromate Capsule: E10-01 Release February 2008 Alcoa F-10

2600/2700 Series Receptacle Installation Instructions Installation Dimensions Type 1 + 3 Receptacles Hole Pattern Type 2 Receptacles Hole Pattern (Side Mounting) Installation Dimensions

36 2600/2700 Series Receptacle Installation Instructions Installation Dimensions Type Receptacles Hole Pattern Type 2 Receptacles Hole Pattern (Side Mounting) Installation Dimensions Installation Options Type 4 Receptacle Accessories Retaining nut Materials / Finish clear chromate Part No. 99N10-01A1 Retaining nut torque 3 +1 Nm Tap 15/32-32UNS- 2B Release February 2008 Alcoa F-11

37 4002 Series Particular Features Max. tensile strength N. Small-size fastener for high tensile load. Wide variety of conventional stud assembly and receptacle design. Floating receptacles available. Selection Instructions 1. Select stud assembly, page G-4 and G-5, grommet and snap-on retaining ring, page G-7 and receptacle, page G-8 and G Select retaining washer, page G-6, for studs from length no Select stud length number from total thickness G using the formula and the table on page G-2 and G-3 insert into stud part number * (e.g *D). Determing the stud length number when using receptacle: Type Type 3 Shim G = P + F G = P + F (8,9 min.) Release February 2008 Alcoa G-1

38 4002 Series Stud Length Table For Using the Following Grommet and Receptacles: Flush Mounting Grommets 4002-G H GS 4002-HS Total Thickness G Stud Length No. When Using Type 1 Receptacles Total Thickness G Stud Length No. When Using Type 2 Receptacles Total Thickness G Stud Length No. When Using Type 3 Receptacles Total Thickness G Stud Length No. When Using Type 4 Receptacles 0,50-1,30 1,30-2,05 2,05-2,80 2,80-3,55 3,55-4,30 4,30-5,10 5,10-5,85 5,85-6,60 6,60-7,30 7,30-8,15 8,15-8,90 8,90-9,65 9,65-10,40 10,40-11,20 11,20-11,95 11,95-12,70 12,70-13,50 13,50-14,20 14,20-15,00 15,00-15,75 15,75-16,50 16,50-17,30 17,30-18,00 18,00-18,80 18,80-19,55 19,55-20,30 20,30-21,10 21,10-21,85 21,85-22,60 22,60-23,40 23,40-24,15 24,15-24,90 24,90-25,65 25,65-26,40 26,40-27, ,50-1,30 1,30-2,05 2,05-2,80 2,80-3,55 3,55-4,30 4,30-5,10 5,10-5,85 5,85-6,60 6,60-7,30 7,30-8,15 8,15-8,90 8,90-9,65 9,65-10,40 10,40-11,20 11,20-11,95 11,95-12,70 12,70-13,50 13,50-14,20 14,20-15,00 15,00-15,75 15,75-16,50 16,50-17,30 17,30-18,00 18,00-18,80 18,80-19,55 19,55-20,30 20,30-21,10 21,10-21,85 21,85-22,60 22,60-23,40 23,40-24,15 24,15-24,90 24,90-25,65 25,65-26, ,90-9,65 9,65-10,40 10,40-11,20 11,20-11,95 11,95-12,70 12,70-13,50 13,50-14,20 14,20-15,00 15,00-15,75 15,75-16,50 16,50-17,30 17,30-18,00 18,00-18,80 18,80-19,55 19,55-20,30 20,30-21,10 21,10-21,85 21,85-22,60 22,60-23,40 23,40-24,15 24,15-24,90 24,90-25,65 25,65-26,40 26,40-27,20 27,20-27,95 27,95-28,70 28,70-29,50 29,50-30,20 30,20-31,00 31,00-31,75 31,75-32,50 32,50-33,30 33,30-34, ,50-1,30 1,30-2,05 2,05-2,80 2,80-3,55 3,55-4,30 4,30-5,10 5,10-5,85 5,85-6,60 6,60-7,30 7,30-8,15 8,15-8,90 8,90-9,65 9,65-10,40 10,40-11,20 11,20-11,95 11,95-12,70 12,70-13,50 13,50-14,20 14,20-15,00 15,00-15,75 15,75-16,50 16,50-17,30 17,30-18,00 18,00-18,80 18,80-19,55 19,55-20,30 20,30-21,10 21,10-21,85 21,85-22,60 22,60-23,40 23,40-24,15 24,15-24,90 24,90-25, ,20-27, ,40-27, ,05-34, ,65-26,40 35 Other lengths on request. Preferred dash-lengths Release February 2008 Alcoa G-2

39 4002 Series Stud Length Table For Using the Following Grommet and Receptacles: Plus Flush Mounting Grommets 4002-N O NS 4002-OS Total Thickness G Stud Length No. When Using Type 1 Receptacles Total Thickness G Stud Length No. When Using Type 2 Receptacles Total Thickness G Stud Length No. When Using Type 3 Receptacles Total Thickness G Stud Length No. When Using Type 4 Receptacles 0,50-1,30 1 0,50-1,30 2 8,90-9,65 3 0,50-1,30 3 1,30-2,05 2 1,30-2,05 3 9,65-10,40 4 1,30-2,05 4 2,05-2,80 3 2,05-2, ,40-11,20 5 2,05-2,80 5 2,80-3,55 4 2,80-3, ,20-11,95 6 2,80-3,55 6 3,55-4,30 5 3,55-4, ,95-12,70 7 3,55-4,30 7 4,30-5,10 6 4,30-5, ,70-13,50 8 4,30-5,10 8 5,10-5,85 7 5,10-5, ,50-14,20 9 5,10-5,85 9 5,85-6,60 8 5,85-6, ,20-15, ,85-6, ,60-7,30 9 6,60-7, ,00-15, ,60-7, ,30-8, ,30-8, ,75-16, ,30-8, ,15-8, ,15-8, ,50-17, ,15-8, ,90-9, ,90-9, ,30-18, ,90-9, ,65-10, ,65-10, ,00-18, ,65-10, ,40-11, ,40-11, ,80-19, ,40-11, ,20-11,95 11,95-12,70 12,70-13,50 13,50-14,20 14,20-15,00 15,00-15,75 15,75-16,50 16,50-17,30 17,30-18,00 18,00-18,80 18,80-19,55 19,55-20,30 20,30-21,10 21,10-21,85 21,85-22,60 22,60-23,40 23,40-24,15 24,15-24,90 24,90-25,65 25,65-26, ,20-11,95 11,95-12,70 12,70-13,50 13,50-14,20 14,20-15,00 15,00-15,75 15,75-16,50 16,50-17,30 17,30-18,00 18,00-18,80 18,80-19,55 19,55-20,30 20,30-21,10 21,10-21,85 21,85-22,60 22,60-23,40 23,40-24,15 24,15-24,90 24,90-25, ,55-20,30 20,30-21,10 21,10-21,85 21,85-22,60 22,60-23,40 23,40-24,15 24,15-24,90 24,90-25,65 25,65-26,40 26,40-27,20 27,20-27,95 27,95-28,70 28,70-29,50 29,50-30,20 30,20-31,00 31,00-31,75 31,75-32,50 32,50-33, ,20-11,95 11,95-12,70 12,70-13,50 13,50-14,20 14,20-15,00 15,00-15,75 15,75-16,50 16,50-17,30 17,30-18,00 18,00-18,80 18,80-19,55 19,55-20,30 20,30-21,10 21,10-21,85 21,85-22,60 22,60-23,40 23,40-24,15 24,15-24, ,40-27, ,65-26, ,30-34, ,90-25,65 35 Other lengths on request. Preferred dash-lengths Release February 2008 Alcoa G-3

) Cross Recess Head yellow chromate 40S5-*D S = 16,00 + (0,76 x length no.

40 4002 Series Stud Assemblies Style Dimensions Materials / Finish C Part No. Slotted Recess Head yellow chromate 4002-*D 1) *S S = 16,00 + (0,76 x length no.) Cross Recess Head yellow chromate 40S5-*D S = 16,00 + (0,76 x length no.) Fixed Wing Head yellow chromate 4002-*WB 1) *SW S = 16,00 + (0,76 x length no.) 180 Folding Bail Handle yellow chromate 40S47-*C S = 20,57 + (0,76 x length no.) * Length no. from Table, page G-2 and G-3 1) Max. tensile strength N. Release February 2008 Alcoa G-4

Sealed Cross Recess Head yellow chromate 100 40S37-*AE Gasket Gasket: Velumoid Additional required gasket see page G-4.

41 4002 Series Stud Assemblies Style Dimensions Materials / Finish C Part No. Hex Recess Head yellow chromate 40E28- *-1AF Sealed Slotted Recess Head yellow chromate S37-*E Gasket Gasket: Velumoid Additional required gasket see page G-4. Sealed Cross Recess Head yellow chromate S37-*AE Gasket Gasket: Velumoid Additional required gasket see page G-4. Installation Dimensions Accessories Materials / Finish Part No. Gasket to be ordered in addition to the sealed stud assembly Gasket Plastic / (PA6) 40S39 40G11-3 Gasket Gasket Gasket: Velumoid 40G S39 Gasket 40S39 Gasket * Length no. from Table, page G-2 and G-3. Release February 2008 Alcoa G-5

42 4002 Series Stud Assemblies Installation Dimensions Accessories Materials / Finish Part No. Retaining washer 4002-SW-SS Stud P Snap-on retaining ring Grommet Retaining washer From stud length no. 16 4P3-1 installation pliers, see below Stud installation pliers 4P3-1 40G26-1 snap-on retaining ring installation tool T26 Release February 2008 Alcoa G-6

43 4002 Series Grommets Style Dimensions Materials / Finish C Part No. Plus Flush Mounting For Panel Thickness up to 1,65 yellow chromate 4002-N NS Plus Flush Mounting For Panel Thickness from 1,65 to 2,40 yellow chromate S Plus Flush Mounting For Panel Thickness from 1,27 to 1,83 yellow chromate 4002-N3-B Flush Mounting For Panel Thickness up to 1,65 yellow chromate 4002-G GS Flush Mounting For Panel Thickness from 1,65 to 2,18 yellow chromate 4002-H HS Grommets for thicker panels upon request. Installation Dimensions Accessories Materials / Finish Part No. Grommet, Plus Flush Mounting Snap-on retaining ring yellow chromate R4G-2 Grommet Snap-on retaining ring T26 installation tool, see page G-6. Grommet, Flush Mounting Grommet T26 installation tool, see page G-6. Release February 2008 Alcoa G-7

44 4002 Series Receptacles Style Dimensions Materials / Finish C Part No. Type 1 Cast Hard bronze / zinc-plated, yellow chromate G S Type 1 Cast Narrow Width Hard bronze / zinc-plated, yellow chromate GN Type 1 Cast Encapsulated Hard bronze / zinc-plated, yellow chromate Capsule: Brass / zinc-plated, yellow chromate R12-1A Type 1 Swage 40R17-1 Release February 2008 Alcoa G-8

45 4002 Series Receptacles Style Dimensions Materials / Finish C Part No. Type 2 Float up to 0,75 mm* (Cast Receptacle) Hard bronze / zinc-plated, yellow chromate Cage: yellow chromate G S Type 2 Float up to 0,75 mm* Encapsulated Hard bronze / zinc-plated, yellow chromate Capsule: yellow chromate GC Type 2 Float up to 0,75 mm (Swage Receptacle) 40R18-1 Type 3 Flat Rivet / Screw or Weld Mounting Weld nib 1,5 Rivet / Screw Mounting Hard bronze / zinc-plated, CrVI-free chromate V50R3-1-1AGV V50R3-1-1BP Welding CrVI-free V50R3-1-2AZ * 1,6 mm float upon request. Release February 2008 Alcoa G-9

46 4002 Series Receptacle Installation Instructions Installation Dimensions Type 1, 2 and 3 Receptacles Hole Pattern Release February 2008 Alcoa G-10

47 991F Series Particular Features Max. tensile strength N. Fastener for maximum tensile strength and preload. Preferred applications: Commercial vehicles, coaches, agricultural machinery, chemical engineering, heating systems etc. 1. Select stud assembly and receptacle, pages H-2, H-3 and H Sealed: Also select rubber gasket and buffer plate, page H Select retaining washer, page H Select stud length number from total thickness G using the formula and table below, insert into stud part number * (e.g. 991S01-*AGV). Determining the stud length number when using: Rivet, Screw and Weld Mounting Receptacle Sealed Stud Assemblies G = P + F G = P + F + 3 Clip-On Receptacle G = P + F Pmin. = 4 F = 1,5-3,5 Total Thickness G Stud Length No. Total Thickness G Stud Length No. Total Thickness G Stud Length No. 0,90-1,65 1,65-2,40 2,40-3,15 3,15-3,95 3,95-4,70 4,70-5,45 5,45-6,20 6,20-7,00 7,00-7,75 7,75-8,50 8,50-9,25 9,25-10,05 10,05-10,80 10,80-11,55 11,55-12,30 12,30-13,10 13,10-13, ,85-14,60 14,60-15,35 15,35-16,15 16,15-16,90 16,90-17,65 17,65-18,40 18,40-19,20 19,20-19,95 19,95-20,70 20,70-21,45 21,45-22,25 22,25-23,00 23,00-23,75 23,75-24,50 24,50-25,25 25,25-26,05 26,05-26, ,80-27,55 27,55-28,30 28,30-29,10 29,10-29,85 29,85-30,60 30,60-31,35 31,35-32,15 32,15-32,90 32,90-33,65 33,65-34,40 34,40-35,20 35,20-35,95 35,95-36,70 36,70-37,45 37,45-38,25 38,25-39, Other lengths on request. Preferred dash-lengths Release February 2008 Alcoa H-1

991F Series Stud Assemblies Style Dimensions Materials / Finish C Part No.

length no.) Fixed Wing Head 991S02- *-1AGV when locked S = 16,26 + (0,76 x length no.

) 180 Folding Wing Head when locked 991S05- *-1AGV when locked S = 16,26 + (0,76 x

48 991F Series Stud Assemblies Style Dimensions Materials / Finish C Part No. Hex Head Slotted Recess 991S01- *-1AGV when locked 1) 991S01- *-1BP S = 16,26 + (0,76 x length no.) Fixed Wing Head 991S02- *-1AGV when locked S = 16,26 + (0,76 x length no.) Offset Fixed Wing Head when locked 991S03- *-1AGV S = 16,26 + (0,76 x length no.) 180 Folding Wing Head when locked 991S05- *-1AGV when locked S = 16,26 + (0,76 x length no.) * Length no. from Table, see page H-1. 1) Max. tensile strength N. Release February 2008 Alcoa H-2

31 +1 _ max 12,5 when looked 991S2991-*AGV Ø9,5 +0,1 _ Ø25 +0,5 _ Ø 3,6 S +0,5 max.

49 991F Series Stud Assemblies Style Dimensions Materials / Finish C Part No. Hex Recess Head max 12,5 when looked 991S30-*AGV Folding Bail Handle 30,5 +1 _ Ø12 +0,5 _ _ max 12,5 when looked 991S2991-*AGV Ø9,5 +0,1 _ Ø25 +0,5 _ Ø 3,6 S +0,5 max ,2 _ * Length no. from Table, see page H-1. S = 15,03 + (0,76 X length no.) Release February 2008 Alcoa H-3

50 991F Series Stud Installation Instructions Installation Dimensions Accessories Material / Finish Part No. Retaining washer 991W04-1BP Slotted retaining washer 991W02-1BP Retaining washer (optional) Sealed Stud Assemblies Installation Dimensions Accessories Material / Finish Part No. Buffer plate 991W03-1BP 16 max when locked Rubber gasket Retaining Buffer plate Rubber gasket NBR black (100 C max.) 991S17-1K washer (optional) Release February 2008 Alcoa H-4

51 991F Series Receptacles Style Dimensions Materials / Finish Rivet / Screw Mounting Rivet / Screw Mounting Mounting Ø C Part No. 3,3 991R2-1AGV 41,2 28,6 22,4 4,1 991R2-3AGV 1,5 D Weld nib 3,3 991R2-1BP 7,5 max. 1,2 4,1 991R2-3BP Welding Steel / zinc-plated - 991R2-2AZ Clip-On zinc flake coated 991R6-1AK7 Frame thickness F= 1,5mm - 3,5mm Receptacle Installation Instructions Installation Dimensions Rivet / Screw or Welding Mounting Clip-On Release February 2008 Alcoa H-5

52 One-Piece Fasteners Release February 2008 Alcoa

V936F Series Particular Features Max. tensile strength 300 N. Same hole shape for panel and frame. Fastener as slotted recess or knurled head version.

Particularly for applications in electro-technical and electronic equipment. For quick installation without tools. Part no.

V936 S11-4 -1 AA Material / Finish Variant Grip range Style Series Style Dimensions Materials / Finish A Slotted Recess Head Stud, spiral pin: clear chromate 12,3 ±0,3

53 V936F Series Particular Features Max. tensile strength 300 N. Same hole shape for panel and frame. Fastener as slotted recess or knurled head version. Fastener position indication by stud slot. Retention type. Vibration resistant. Grip ranges from 2,0 mm to 4,6 mm. Unlock and lock by a quarter turn. Particularly for applications in electro-technical and electronic equipment. For quick installation without tools. Part no. example Knurled head for 3,3 mm to 4,6 mm grip range. V936 S AA Material / Finish Variant Grip range Style Series Style Dimensions Materials / Finish A Slotted Recess Head Stud, spiral pin: clear chromate 12,3 ±0,3 14,8 ±0,3 Grip Range G 2,0-3,2 3,3-4,6 Part No. V936S05-3-1AA V936S05-4-1AA Compression spring: Casing: Zinc die casting / zincplated, clear chromate Knurled Head Stud, Casing: Zinc die casting / zincplated, clear chromate 26,4 ±0,3 28,9 ±0,3 2,0-3,2 3,3-4,6 V936S11-3-1AA V936S11-4-1AA Compression spring: Spiral pin: clear chromate Release February 2008 Alcoa I-1

54 V936F Series Installation Instructions Hole Shape in Panel P Installing the fastener The slot indicates the position of the fastener Unlocked Hole Shape in Panel F Fastener retaining in panel Locked Release February 2008 Alcoa I-2

55 713F Series Particular Features This fastener mounts panels in electrical switch cabinets (e.g. 19 -equipment) to modular bars. Selection Instructions The dimensions of the front panel and the modular bar as well as the colour determine the final design of the fastener. To enable us to offer you the custom-tailored fastener, we need your drawings with the dimensions and tolerances of: 1. the front panel 2. the shape of the modular bar 3. the colour, if necessary In addition, please send us samples of your modular bar and front panel. Part no. example One-piece fastener 713 S* - * AE Materials / Finish Colour (as requested by the customer) Head style and design (as requested by the customer) Series Release February 2008 Alcoa J-1

chromate -25 up to +90 713S*- *AE Knurled Head Stud Spring Spring cup Casement fastener Spring cup: Plastic (POM) Stud: Steel / nickel-plated Spring: clear chromate Casement fastener: Zinc die

56 713F Series Modular Bar Fasteners Style Dimensions Materials / Finish C Part No. Slotted Recess Head Stud Spring Spring cup Casement fastener Spring cup: Plastic (POM) Stud: Steel / nickel-plated Spring: clear chromate Casement fastener: Zinc die casting / zinc-plated, clear chromate -25 up to S*- *AE Knurled Head Stud Spring Spring cup Casement fastener Spring cup: Plastic (POM) Stud: Steel / nickel-plated Spring: clear chromate Casement fastener: Zinc die casting / zinc-plated, clear chromate -25 up to S*- *AE * Design and colour as requested by the customer. Due to the various front panel thickness, hole shapes and modular bar shapes, it is not possible to offer one standard design. We will individually issue the final part number only after determining the front panel and modular bar dimensions and the colour. Dimensions Fastener Position Installing the Fastener Unlocked Locked Zum Schließen Verschlusszapfen To lock push stud and turn 90 C. 1. Insert fastener with spring cup into hole. 2. Push stud until snap-in hooks lock in. The slot indicates the position of the fastener. Release February 2008 Alcoa J-2

57 Push Button Fasteners Release February 2008 Alcoa

58 15F Series Particular Features Max. tensile strength N. Quick opening and closing by a finger push. Easy installation by single hole mounting. Selection Instructions 1. Select stud assembly, page K-2 and receptacle, page K Select retaining washer, page K-2 and retaining hexnut, page K-3, if necessary. 3. Select stud length number from Panel thickness P using the table below, insert into stud part number * (e.g. 15S1-*-1AD). Stud Length Table Panel Thickness P 0,7-2,3 2,3-3,8 3,8-5,3 5,3-6,9 6,9-8,4 8,4-9,9 9,9-11,4 11,4-13,0 Stud Length No Other lengths on request. Preferred dash-lengths Release February 2008 Alcoa K-1

15F Series Stud Assemblies Style Dimensions Materials / Finish C Part No. Steel / nickel-plated 15S1- *-1AD Steel / zinc-plated 15S1- *-1AJ S=22,4 + (0,76 x length no.) * Length no.

59 15F Series Stud Assemblies Style Dimensions Materials / Finish C Part No. Steel / nickel-plated 15S1- *-1AD Steel / zinc-plated 15S1- *-1AJ S=22,4 + (0,76 x length no.) * Length no. from Table, see page K-1. Other lengths and surfaces can be ordered upon request. Installation Dimensions Panel thickness up to 4,8 Stud Installation Instructions Accessories Materials / Finish Part No. Retaining washer 15S11-1CJ Panel thickness up to 4,8 Retaining washer Installation Tool for 15S11-1CJ retaining washer T107-1 Release February 2008 Alcoa K-2

60 15F Series Receptacle Style Dimensions Materials / Finish C Part No. 15,2 Zinc die casting / zinc-plated 150 V15R13-1-1AB Installation Dimensions Receptacle Installation Instructions Accessories Hex Nut Materials / Finish transparent passivated Part No. V15R14-1-1AB Nut Release February 2008 Alcoa K-3

61 Push-Turn Fasteners Release February 2008 Alcoa

62 715F Series Particular Features Max. tensile strength 700 N. Easy and economic clip-in installation for stud and receptacle. Also suitable for automatic installation. Opening by 1/4 turn - closing by a finger push. Due to their small size, particulary suited for use in electrical engineering / electronics. Selection Instructions 1. Select stud assembly according to panel thickness P, page L-2 and spring clip according to frame thickness F, page L Select stud length number form panel thickness G using the table below, insert into stud part number * (e.g. 715S12-*-1BP). Part no. example Stud, slotted recess head 715 S BP Variant Length No. Style Series Stud Length Table Panel Thickness P Slotted Recess Head Stud Length No. Knurled Head Stud Length No. Panel Thickness P Slotted Recess Head Stud Length No. Knurled Head Stud Length No. 0,50-1,25 1,25-2,00 2,00-2,75 2,75-3,50 3,50-4,25 4,25-5,00 5,00-5,75 5,75-6, ,50-7,25 7,25-8,00 8,00-8,75 8,75-9,50 9,50-10,25 10,25-11,00 11,00-11,75 11,75-12, Other lengths on request. Preferred dash-lengths Release February 2008 Alcoa L-1

) Knurled Head 15 max when locked Spring cup: Plastic (POM) / black 0,5-1,0 1,0-1,5 1,5-2,0-40 up to +100 715S13- *-1BP 715S13- *-2BP 715S13-

63 715F Series Stud Assemblies Style Dimensions Materials / Finish Slotted Recess Head 4,5 max when locked Spring cup: Plastic (POM) / black Panel Thickness P 0,5-1,0 1,0-1,5 1,5-2,0 C Part No. -40 up to S12- *-1BP 715S12- *-2BP 715S12- *-3BP (1 deep) S = 13,25 + (0,75 x length no.) Knurled Head 15 max when locked Spring cup: Plastic (POM) / black 0,5-1,0 1,0-1,5 1,5-2,0-40 up to S13- *-1BP 715S13- *-2BP 715S13- *-3BP S = 13,25 + (0,75 x length no.) Installation Dimensions Stud Installation Instructions Panel up to 2 mm Panel over 2 mm Release February 2008 Alcoa L-2

64 715F Series Receptacle Style Dimensions Materials / Finish Frame Thickness F Receptacle 0,5-1,0 1,0-1,5 C Part No. -40 up to R02-1BP 715R02-2BP 1,5-2,0 (See stud assembly) 715R02-3BP 2,0-2,5 715R02-4BP Installation Instructions Installation Dimensions Release February 2008 Alcoa L-3

65 716F Series Particular Features Max. tensile strength N. Easy and economic clip-in installation for stud and receptacle. Also suitable for automatic installation. Opening by 1/4 turn - closing by a finger push. Selection Instructions 1. Select stud assembly according to panel thickness P, page M-2 and spring clip according to frame thickness F, page M Select stud length number from panel thickness P using table below, insert into stud part number * (e.g. 716S12-*-1BP). Part no. example Stud, slotted recess head 716 S BP Variant Length No. Style Series Panel Thickness P 1,0-2,0 2,0-3,0 3,0-4,0 4,0-5,0 5,0-6,0 6,0-7,0 7,0-8,0 8,0-9,0 9,0-10,0 Stud Length Table Stud Length No Other lengths on request. Preferred dash-lengths Release February 2008 Alcoa M-1

716F Series Stud Assemblies Style Dimensions Materials / Finish Slotted Recess Head 5,5 max when locked Spring cup: Plastic (POM) / black Frame Thickness F 0,5-1,0 1,0-1,5 1,5-2,0 2,0-2,5 2,5-3,0 C

66 716F Series Stud Assemblies Style Dimensions Materials / Finish Slotted Recess Head 5,5 max when locked Spring cup: Plastic (POM) / black Frame Thickness F 0,5-1,0 1,0-1,5 1,5-2,0 2,0-2,5 2,5-3,0 C Part No. -40 up to S12- *-1BP 716S12- *-2BP 716S12- *-3BP 716S12- *-4BP 716S12- *-5BP (1,5 deep) S = 18,5 + length no. Knurled Head 15,5 max when locked Spring cup: Plastic (POM) / black 0,5-1,0 1,0-1,5 1,5-2,0-40 up to S13- *-1BP 716S13- *-2BP 716S13- *-3BP 2,0-2,5 716S13- *-4BP 2,5-3,0 716S13- *-5BP S = 18,5 + length no. * Length no. from Table, page M-1. Stud Installation Instructions Installation Dimensions Panel up to 3 mm Panel over 3 mm Release February 2008 Alcoa M-2

67 716F Series Receptacle Style Dimensions Materials / Finish Frame Thickness F Spring Clip 1,0-1,5 1,5-2,0 C Part No. -40 up to R01-1B 720R01-2B 2,0-2,5 (See stud assembly) 720R01-3B 2,5-3,0 720R01-4B Installation Instructions Installation Dimensions Release February 2008 Alcoa M-3

68 717F Series Particular Features Max. tensile strength N. Robust design - high strength. Stud assembly with protective, compensating and retaining washers. Rivet and screw mounting spring clip. Opening by 1/4 turn - closing by a finger push. Selection Instructions 1. Select stud assembly and spring clip, page N-2 and N Select compensating and retaining washers, page N Select stud length number from grip range G using the table below, insert into stud part number * (e.g. 717S01-*-1AGV). Part no. example Spring clip, rivet / screw mounting 717 S AF Protective washer Variant Length No. Series Compensating washer Retaining washer G = P + F Griprange G 1,0-3,0 3,0-5,0 5,0-7,0 7,0-9,0 9,0-11,0 11,0-13,0 Stud Length Table Stud Length No Other lengths on request. Preferred dash-lengths Release February 2008 Alcoa N-1

) Knurled Head Steel/ zinc-plated -40 up to +100 717S01- *-2AGV S = 20,5 + (2 x length no.) * Length no. from Table, see page N-1.

69 717F Series Stud Assemblies Style Dimensions Materials / Finish C Part No. Slotted Recess Head Steel/ zinc-plated -40 up to S01- *-1AGV S = 20,5 + (2 x length no.) Knurled Head Steel/ zinc-plated -40 up to S01- *-2AGV S = 20,5 + (2 x length no.) * Length no. from Table, see page N-1. Stud Installation Instructions Style Dimensions Materials / Finish C Part No. Protective washer Plastic (PA6) / natural colour -40 up to W02-1K Compensating washer Plastic (PU-foam) / anthracite -40 up to W03-1K Retaining washer Plastic (PA6) / natural colour -40 up to W01-1K Release February 2008 Alcoa N-2

70 717F Series Receptacle Style Dimensions Materials / Finish C Part No. Rivet / Screw Mounting Steel / zinc flake coated -40 up to R01-1AK7 Installation Instructions Installation Dimensions Release February 2008 Alcoa N-3

71 720F Series Particular Features Max. tensile strength N. Easy and economic installation by snap-in spring clip. Easy installation of stud and washer without tool. Tool or hand operated. Tool operated with combination recess. Opening by 1/4 turn - closing by a finger push. Wide grip range. Selection Instructions 1. Select stud assembly according to panel thickness P, page O-2 and spring clip according to frame thickness F, page O Select Compensating washer and Retaining washer, page O Select stud length number from panel thickness P using the formula and table below, insert into stud part number * (e.g. 720S01-*B). Part no. example Stud, slot-cross recess 720 S01 -*B Length No. Style Series Panel Thickness P Slot-Cross Recess Length No. Wing Head Stud Length No. Dimension L +0,1/-0,2 Dimension (S) 1,00-4,00 4,00-7,00 7,00-10, Preferred dash-lengths Release February 2008 Alcoa O-1

72 720F Series Stud Assemblies Style Dimensions Materials / Finish C Part No. Slot-Cross Recess Head Washer: PA6 natural -20 up to S01-*B L + (S) see table page O-1 Wing Head Knob: PA6 black Washer: PA6 natural -20 up to S02-*B L + (S) see table page O-1 * Length no. from Table, see page O-1. Installation Dimensions Stud Installation Instructions Release February 2008 Alcoa O-2

Polyamid natural -20 up to +70 50E15-1K Polyamid natural Mounting Instructions Polyamid

73 720F Series Stud Assemblies Style Dimensions Materials / Finish C Part No. Compensation Washer PU - Elastomer yellow -20 up to W01-2K Retaining Washer Polyamid natural -20 up to E15-1K Polyamid natural Mounting Instructions Polyamid natural Compensation Washer Compensation Washer Retaining Washer Retaining Washer Release February 2008 Alcoa O-3

74 720F Series Receptacle Style Dimensions Materials / Finish Frame Thickness F Spring Clip 1,0-1,5 1,5-2,0 C Part No. -40 up to R01-1B 720R01-2B 2,0-2,5 2,5-3,0 Please note the restrictions caused to stud assemblies 720R01-3B 720R01-4B Installation Instructions Installation Dimensions Release February 2008 Alcoa O-4

75 Pawl Latches Release February 2008 Alcoa

V964L Series Particular Features Wide grip range (total thickness G up to 15 mm). Universally applicable. Easy installation by single-hole mounting.

V964L 01-1 -2AG Variant Head style (slotted recess) Style G = P + F Series Style Dimensions Materials / Finish C Part No.

76 V964L Series Particular Features Wide grip range (total thickness G up to 15 mm). Universally applicable. Easy installation by single-hole mounting. Either tool-operated (slotted recess head) or hand-operated (fixed wing head). Clockwise locking. Part no. example Pawl Latches, slotted recess head, with limit washer. V964L AG Variant Head style (slotted recess) Style G = P + F Series Style Dimensions Materials / Finish C Part No. Slotted Recess Head Stud: Steel / zinc-plated V964L01-1-1AG 2 (4 deep) Spring: Slotted Recess Head with Decorative Washer Limit washer Stud: Steel / zinc-plated V964L01-1-2AG 2 (4 deep) Spring: Fixed Wing Head Stud: Steel / zinc-plated -40 up to +100 V964L01-2-1AG Spring: Wing: Plastic (POM) black Release February 2008 Alcoa P-1

77 V964L Series Installation Instructions Installation Dimensions Locked Unlocked Release February 2008 Alcoa P-2

V965L Series Particular Features Two wide grip ranges from 1,0 mm to 18,8 mm to choose from - continuously adjustable. Two different head styles available.

V965L 23-1 R1AG Locking Direction Grip Range (1,0 mm - 12,2 mm) Head Style G = P + F Series Style Dimensions Materials / Finish C Part No.

78 V965L Series Particular Features Two wide grip ranges from 1,0 mm to 18,8 mm to choose from - continuously adjustable. Two different head styles available. Easy single hole mounting - low installation cost. Clockwise locking. Counterclockwise locking fasteners upon request. Part no. example Pawl Latches, fillister head. Grip range 1,0 mm - 12,2 mm. V965L 23-1 R1AG Locking Direction Grip Range (1,0 mm - 12,2 mm) Head Style G = P + F Series Style Dimensions Materials / Finish C Part No. Flat Head Grip Range 1,0 up to 12,2 Steel / zinc-plated -40 up to +100 V965L23-1R1AG Grip range 1,0 up to 12,2 Retaining washer closing angle 90 Flat Head Grip Range 7,6 up to 18,8 Steel / zinc-plated -40 up to +100 V965L23-2R1AG Grip range 7,6 up to 18,8 Retaining washer closing angle 90 Release February 2008 Alcoa Q-1

79 V965L Series Pawl Latches Style Dimensions Materials / Finish C Part No. Knurled Head Grip Range 1,0 up to 12,2 Steel / zinc-plated -40 up to +100 V965L1-1R1AG Grip range 1,0 up to 12,2 Retaining washer closing angle 90 Knurled Head Grip Range 7,6 up to 18,8 Steel / zinc-plated -40 up to +100 V965L1-2R1AG Retaining washer Grip range 7,6 up to 18,8 closing angle 90 Pawl Latches Installation Instructions Instruction Dimensions Clockwise locking Release February 2008 Alcoa Q-2

2600/2700 Series. Determining the stud length number when using receptacle: Type 1 + 3* G = P + F. * For Type 3: G = 9,9 mm min.

2600/2700 Series. Determining the stud length number when using receptacle: Type 1 + 3* G = P + F. * For Type 3: G = 9,9 mm min. Particular Features Max. tensile strength 1.330 N. Small-size fastener for high tensile load. Wide variety of conventional stud assembly and receptacle designs. 2600 Series: Fillister head; 2700 Series: