The steering column is of a modular construction and features easy to service electrical switches.

Size: px
Start display at page:

Download "The steering column is of a modular construction and features easy to service electrical switches."

Transcription

1 file://c:\tso\tsocache\vdtom_5368\svk~us~en~file=svkb4a01.htm~gen~ref.htm Page 1 of 3 Section 11-04A: Steering Column, Ranger DESCRIPTION AND OPERATION 1997 Ranger Workshop Manual Steering Column NOTE: All fasteners are important in that they could affect the performance of vital parts and systems, and/or could result in major service expenses. They must be replaced with new fasteners of the same part number if replacement becomes necessary. Do not use a replacement part of lesser quality or substitute design. Torque values must be used as specified during assembly to ensure proper functioning of these parts. The steering column is of a modular construction and features easy to service electrical switches. The structural part of the steering column is made of magnesium die castings. At the lower end, the steering column is attached to the instrument panel support by a bend bracket. The bend bracket is designed so that during a collision: a. The steering column will remain stationary during air bag deployment. b. If, after air bag deflation, the driver should strike the steering column, the bend bracket will bend in a controlled manner absorbing the impact of the driver striking the column and reducing injury. The upper end of the steering column is attached to the instrument panel support by shear modules. They are designed to shear if, during a collision, the driver should strike the steering column after air bag deployment and deflation. This allows the bend bracket to absorb the force of the impact as described above. Tilt Steering Column, Ranger

2 file://c:\tso\tsocache\vdtom_5368\svk~us~en~file=svkb4a01.htm~gen~ref.htm Page 2 of 3 Item Part Number Description Steering Shaft Turn Indicator Cancel Cam 3 Ignition Lock Cylinder Pocket (Part of 3511) Lock Cylinder Housing 5 3F723 Steering Actuator Housing 6 Shear Module (Part of 3F723) Bend Bracket Ignition Switch 9 3D544 Steering Column Release Lever

3 file://c:\tso\tsocache\vdtom_5368\svk~us~en~file=svkb4a01.htm~gen~ref.htm Page 3 of 3

4 file://c:\tso\tsocache\vdtom_5368\svk~us~en~file=svkb4a02.htm~gen~ref.htm Page 1 of 1 Section 11-04A: Steering Column, Ranger DESCRIPTION AND OPERATION 1997 Ranger Workshop Manual Fixed and Tilt Columns Both fixed and tilt columns are similar in design. On the tilt column, a latch mechanism is included to allow unlatching, raising, and lowering the upper third of the steering column with the steering wheel. The tilt column has pivot screws and a universal joint in the steering shaft to allow tilting. On a fixed column, the steering shaft is rigid. A unique steering column-mounted shift mechanism is used. It has the transmission shift selector position insert (7A216) plate located away from the gearshift lever (7210) and interacts with the gearshift lever through a linkage system. This system incorporates a brake shift interlock which prevents shifting out of Park unless the brake pedal (2455) is depressed.

5 file://c:\tso\tsocache\vdtom_5368\svk~us~en~file=svkb4a03.htm~gen~ref.htm Page 1 of 1 Section 11-04A: Steering Column, Ranger DESCRIPTION AND OPERATION 1997 Ranger Workshop Manual Steering Column with Air Bag The steering column incorporates a driver side air bag module (043B13) in the steering wheel (3600). Refer to Section 01-20B for passive restraint information.

6 file://c:\tso\tsocache\vdtom_5368\svk~us~en~file=svkb4a04.htm~gen~ref.htm Page 1 of 5 Section 11-04A: Steering Column, Ranger DESCRIPTION AND OPERATION 1997 Ranger Workshop Manual Steering Column Lock The steering column is equipped with a lock mechanism which locks the steering wheel (3600), ignition switch, and gearshift lever (7210) when the ignition switch lock cylinder (11582) is turned to the LOCK position. Lock Cylinder Housing Assembly, Steering Column Item Part Number Description 1 3D655 Steering Column Position Spring 2 N S Pin, Knurled Straight, M4.7 x 3.97mm x 53.8mm

7 file://c:\tso\tsocache\vdtom_5368\svk~us~en~file=svkb4a04.htm~gen~ref.htm Page 2 of 5 3 3D544 Steering Column Release Lever 4 N S Pin, Knurled Straight Lock Cylinder Housing 6 3D656 Bumper Steering Column Bearing (Large) Steering Shaft Tilt 9 3E715 Steering Column Lock Lever Actuator 10 3D655 Steering Column Position Spring 11 3B654 Bushing 12 3E695 Steering Column Lock Cam 13 3C610 Bearing Retainer 14 3E700 Steering Column Lock Housing Bearing 15 3E717 Steering Column Lock Gear Steering Column Upper Bearing Spring 17 3C610 Bearing Retainer Turn Indicator Cancel Cam Steering Column Bearing Sleeve 20 3L539 Steering Column Bearing Tolerance Ring Steering Column Bearing (Small) 22 3F578 Spacer (Fixed Column) 23 3E729 Steering Shaft (Fixed Column) 24 3F527 Lever Assembly (Manual Transmission) 25 3F530 Pin (Manual Transmission) Shift Tube Assembly, Steering Column Automatic Transmission

8 file://c:\tso\tsocache\vdtom_5368\svk~us~en~file=svkb4a04.htm~gen~ref.htm Page 3 of 5 Item Part Number Description 1 7C464 Clip, Transmission Control Select Lever Spring 2 7E400 Gearshift Tube Bushing Clamp 3 N S36 Screw 4 7L278 Gearshift Tube Bushing 5 7D282 Transmission Shift Selector Position Lever 6 7A216 Transmission Shift Selector Position Insert 7 3Z719 Brake Shift Interlock Solenoid Transmission Selector Lever Arm and Support Gearshift Selector Tube Spring 10 7W441 Gearshift Lever Pin Transmission Column Shift Selector Tube 12 7R264 Column Shift Selector Lever Plunger Steering Actuator Assembly, Steering Column Item Part Number 1 N S36 Screw 2 N Pin Description

9 file://c:\tso\tsocache\vdtom_5368\svk~us~en~file=svkb4a04.htm~gen~ref.htm Page 4 of 5 3 3E691 Steering Column Lock Pawl 4 14A099 Steering Column Lock Actuator Cover (Manual Transmission) 5 3F723 Steering Actuator Housing Bend Bracket (Automatic Transmission Shown) 7 3D681 Steering Column Lower Bearing Retainer Steering Column Lower Bearing Sleeve Steering Column Lower Bearing 10 N S36 Screw 11 3L539 Steering Column Lower Bearing Tolerance Ring 12 3C131 Suspension Height Sensor Control Ring Steering Column Lower Bearing Spring 14 3C610 Retainer, Steering Column Lower Bearing (Fixed Column) 15 N S36 Screw Ignition Switch (High Profile) 17 3B663 Steering Column Lock Lever Pin 18 3B768 Steering Column Position Lock Spring 19 3D653 Steering Column Lock Left Hand Lever 20 3D653 Steering Column Lock Left Hand Lever (with Tilt Column) 21 3B662 Steering Column Lock Right-Hand Lever (with Tilt Column) 22 3E715 Steering Column Lock Lever Actuator 23 3E696 Steering Column Lock Spring 24 3E691 Steering Column Shaft Lock Pawl

10 file://c:\tso\tsocache\vdtom_5368\svk~us~en~file=svkb4a04.htm~gen~ref.htm Page 5 of 5

11 file://c:\tso\tsocache\vdtom_5368\svk~us~en~file=svkb4a06.htm~gen~ref.htm Page 1 of 5 Section 11-04A: Steering Column, Ranger REMOVAL AND INSTALLATION 1997 Ranger Workshop Manual Steering Wheel with Air Bag CAUTION: Do not remove the steering column, steering wheel (3600), and driver side air bag module (043B13) as an assembly from the vehicle unless the column is locked to prevent rotation. Lower end of steering shaft should be wired to prevent the steering wheel from being rotated and causing the air bag sliding contact (14A664) to become misindexed. SPECIAL SERVICE TOOL(S) REQUIRED Description Tool Number Differential Side Bearing Puller T77F-4220-B1 Removal WARNING: THE ELECTRICAL CIRCUIT FOR AIR BAG DEPLOYMENT IS POWERED DIRECTLY FROM THE BATTERY AND BACKUP POWER SUPPLY. TO AVOID ACCIDENTAL DEPLOYMENT AND POSSIBLE PERSONAL INJURY, THE BATTERY POSITIVE CABLE MUST BE DISCONNECTED FOR A MINIMUM OF ONE MINUTE TO DE-ENERGIZE THE BACKUP POWER SUPPLY PRIOR TO SERVICING OR REPLACING ANY AIR BAG SYSTEM COMPONENTS. 1. Center front wheels (1007) to the straight-ahead position. 2. Disconnect battery to starter relay cable (14300) and wait at least one minute to let the air bag backup power supply discharge. Refer to Section 01-20B. 3. Pry out two plugs covering driver side air bag module screws on sides of steering wheel.

12 file://c:\tso\tsocache\vdtom_5368\svk~us~en~file=svkb4a06.htm~gen~ref.htm Page 2 of 5 4. Remove two driver side air bag module retaining screws on side of steering wheel from driver side air bag module, and lift driver side air bag module away from steering wheel. 5. Disconnect driver side air bag wire harness connector at the air bag sliding contact, horn control wire harness connector, and, if equipped, speed control harness connector.

13 file://c:\tso\tsocache\vdtom_5368\svk~us~en~file=svkb4a06.htm~gen~ref.htm Page 3 of 5 6. Loosen, but do not remove, steering wheel retaining bolt approximately 2 to 3 turns. 7. Install Differential Side Bearing Puller T77F-4220-B1 at the areas marked PULL near the loosened steering wheel retaining bolt. 8. CAUTION: Be sure air bag sliding contact assembly wire harness does not get caught on steering wheel assembly when lifting steering wheel off steering shaft. Pull steering wheel loose and remove Differential Side Bearing Puller T77F-4220-B1. 9. Remove and discard original steering wheel bolt. 10. Remove steering wheel while routing wires from air bag sliding contact through steering wheel. Installation NOTE: If a new air bag sliding contact is being installed, remove the plastic lock tool after

14 file://c:\tso\tsocache\vdtom_5368\svk~us~en~file=svkb4a06.htm~gen~ref.htm Page 4 of 5 intermediate shaft is connected to steering gear. 1. Make sure the vehicle's front wheels are in the straight-ahead position. 2. CAUTION: Be sure wiring does not get trapped between steering wheel and air bag sliding contact. Route air bag sliding contact wire harnesses through steering wheel opening at the three o'clock position. Position steering wheel on steering shaft so the alignment marks on wheel and shaft are aligned. Be sure air bag contact wire is not pinched. 3. Install new steering wheel retaining bolt and tighten to Nm (25-34 lb-ft). 4. Connect horn/speed control wire harness to air bag sliding contact wire harness. Connector is located on right side of steering wheel retaining bolt. 5. Connect air bag sliding contact wire harness to driver side air bag module and position air bag into steering wheel. Install driver side air bag module retaining bolts. 6. Hold driver side air bag module in position in steering wheel while bolts are being torqued to ensure proper fit. Tighten bolts to Nm (67-92 lb/in). 7. Install two cover plugs by snapping into holes on sides of steering wheel. 8. NOTE: When the battery (10655) has been disconnected and reconnected, some abnormal driving symptoms may occur while the powertrain control module (PCM) (12A650) relearns its adaptive strategy. The vehicle may need to be driven 16 km (10 miles) or more for the powertrain control module to relearn the strategy. Connect battery to starter relay cable. Verify air bag warning indicator. Steering Wheel with Air Bag Item Part Number Description

15 file://c:\tso\tsocache\vdtom_5368\svk~us~en~file=svkb4a06.htm~gen~ref.htm Page 5 of B13 Driver Side Air Bag Module 2 N S100 Torx Head Screw, M x Steering Wheel 4 14A664 Air Bag Sliding Contact 5 3C529 Steering Column 6 Clip (Part of 14A664) 7 3F785 Plug 8 N S424 Bolt 9 N S36MG Bolt A Tighten to Nm (25-33 Lb-Ft) B Tighten to Nm (61-92 Lb-In) C Tighten to Nm ( Lb-Ft)

16 file://c:\tso\tsocache\vdtom_5368\svk~us~en~file=svkb4a07.htm~gen~ref.htm Page 1 of 9 Section 11-04A: Steering Column, Ranger REMOVAL AND INSTALLATION 1997 Ranger Workshop Manual Steering Column, Fixed and Tilt Removal WARNING: THE ELECTRICAL CIRCUIT NECESSARY FOR AIR BAG SYSTEM DEPLOYMENT IS POWERED DIRECTLY FROM THE BATTERY AND A BACKUP POWER SUPPLY. TO AVOID ACCIDENTAL DEPLOYMENT AND POSSIBLE PERSONAL INJURY, THE BATTERY POSITIVE CABLE MUST BE DISCONNECTED FOR A MINIMUM OF ONE MINUTE TO DE-ENERGIZE THE BACKUP POWER SUPPLY PRIOR TO REMOVING ANY OF THE AIR BAG SYSTEM COMPONENTS. NOTE: All components of the steering column are assembled with fasteners which are designed to prevent loosening due to vibrations associated with normal vehicle operation. 1. Park vehicle with the wheels (1007) in a straight-ahead position. 2. Disconnect the battery to starter relay cable (14300) and wait for one minute before beginning to remove steering column assembly. 3. Remove steering wheel (3600) as outlined in this section. 4. Remove two screws and instrument panel steering column cover (04459). 5. Remove six screws and instrument panel reinforcement (017A28). 6. Remove two screws and steering column opening center reinforcement. Instrument Panel Steering Column Cover and Reinforcement

17 file://c:\tso\tsocache\vdtom_5368\svk~us~en~file=svkb4a07.htm~gen~ref.htm Page 2 of 9 Item Part Number Instrument Panel Description 2 044C86 Instrument Panel Steering Column Opening Center Reinforcement 3 N S58 4 N S36 5 N S411 Nuts Screw Screw 6 044D82 Instrument Panel Access Hole Cover Instrument Panel Steering Column Cover 8 017A28 Instrument Panel Reinforcement A Tighten to Nm ( Lb-In) B Tighten to Nm ( Lb-In) C Tighten to Nm (19-25 Lb-In) 7. Disconnect electrical connectors between main wiring (14401) and steering column. Disconnect brake shift interlock solenoid.

18 file://c:\tso\tsocache\vdtom_5368\svk~us~en~file=svkb4a07.htm~gen~ref.htm Page 3 of 9 8. Disconnect transmission control selector indicator loop from transmission column shift selector tube (7212). Remove screw and transmission range indicator (7A110) from steering column.

19 file://c:\tso\tsocache\vdtom_5368\svk~us~en~file=svkb4a07.htm~gen~ref.htm Page 4 of 9 9. Remove steering shaft-to-intermediate shaft universal joint pinch bolt. 10. Remove four nuts securing steering column to instrument panel reinforcement (04545).

20 file://c:\tso\tsocache\vdtom_5368\svk~us~en~file=svkb4a07.htm~gen~ref.htm Page 5 of Lower steering column to floor. 12. Using screwdriver, snap shift cable off of selector lever arm. 13. Using screwdriver, lift tab on shift cable retainer and remove shift cable from bend bracket.

21 file://c:\tso\tsocache\vdtom_5368\svk~us~en~file=svkb4a07.htm~gen~ref.htm Page 6 of 9

22 file://c:\tso\tsocache\vdtom_5368\svk~us~en~file=svkb4a07.htm~gen~ref.htm Page 7 of Remove steering column from vehicle. Installation 1. Position steering column on floor of vehicle. 2. Push shift cable retainer into slot on bend bracket and snap shift cable end onto shaft of selector lever arm. 3. Insert steering column shaft into universal joint, (part of intermediate shaft) making sure cutout in steering column shaft aligns with universal joint pinch bolt hole. 4. Raise steering column into position onto instrument panel reinforcement studs. 5. Install instrument panel steering column opening brace. 6. Install four nuts securing steering column. Tighten to Nm (10-12 lb/ft). 7. Install steering column shaft-to-universal joint pinch bolt. Tighten to Nm (30-40 lb-ft). 8. Install transmission range indicator. Connect cable loop to transmission column shift selector lever. 9. Connect main wiring to steering column electrical connectors. Connect shift lock actuator (3Z719).

23 file://c:\tso\tsocache\vdtom_5368\svk~us~en~file=svkb4a07.htm~gen~ref.htm Page 8 of Install instrument panel steering column cover reinforcement and tighten screws to Nm ( lb-in). 11. Install instrument panel steering column cover and tighten screws to Nm (19-25 lb-in). 12. Install steering wheel as outlined in this section. Steering Column Installation Item Part Number Description Instrument Panel Reinforcement Steering Column Shroud (Upper) Gearshift Lever 4 3C529 Steering Column 5 3F609 Tilt Wheel Handle and Shank S2 Screw Steering Column Shroud (Lower) 8 N S58 Nut 9 7E395 Shift Cable and Bracket A Tighten to Nm (7-9 Lb-In) B Tighten to Nm (10-12 Lb-Ft)

24 file://c:\tso\tsocache\vdtom_5368\svk~us~en~file=svkb4a07.htm~gen~ref.htm Page 9 of 9

25 file://c:\tso\tsocache\vdtom_5368\svk~us~en~file=svkb4a08.htm~gen~ref.htm Page 1 of 3 Section 11-04A: Steering Column, Ranger REMOVAL AND INSTALLATION 1997 Ranger Workshop Manual Multi-Function Switch Removal WARNING: THE ELECTRICAL CIRCUIT FOR AIR BAG DEPLOYMENT IS POWERED DIRECTLY FROM THE BATTERY AND BACKUP POWER SUPPLY. TO AVOID ACCIDENTAL DEPLOYMENT AND POSSIBLE PERSONAL INJURY, THE BATTERY POSITIVE CABLE MUST BE DISCONNECTED FOR A MINIMUM OF ONE MINUTE TO DE-ENERGIZE THE BACKUP POWER SUPPLY. 1. Disconnect battery to starter relay cable (14300) and wait at least one minute for air bag backup power supply to discharge before beginning work. Refer to Section 01-20B. 2. Remove upper and lower steering column shrouds (3530) as outlined in this section. 3. Remove two self-tapping screws retaining multi-function switch (13K359) to steering column tube casting. Disengage multi-function switch from casting.

26 file://c:\tso\tsocache\vdtom_5368\svk~us~en~file=svkb4a08.htm~gen~ref.htm Page 2 of 3 4. Disconnect the three electrical connectors. Installation 1. Install three electrical connectors to full engagement. 2. Align turn signal and windshield wiper switch mounting holes with corresponding holes in steering column tube casting. Install two self-tapping screws, making sure to start screws in the previously tapped holes. Tighten to 2-3 Nm (18-25 lb-in). 3. Install upper steering column shroud and lower steering column shroud with screws. Tighten to Nm (7-9 lb-in). 4. NOTE: When the battery (10655) has been disconnected and reconnected, some abnormal drive symptoms may occur while the powertrain control module (PCM) (12A650) relearns it adaptive strategy. The vehicle may need to be driven 16 km (10 miles) or more to relearn the strategy. Connect battery to starter relay cable.

27 file://c:\tso\tsocache\vdtom_5368\svk~us~en~file=svkb4a08.htm~gen~ref.htm Page 3 of 3 5. Check tilt lock lever and multi-function switch for proper operation.

28 file://c:\tso\tsocache\vdtom_5368\svk~us~en~file=svkb4a09.htm~gen~ref.htm Page 1 of 5 Section 11-04A: Steering Column, Ranger REMOVAL AND INSTALLATION 1997 Ranger Workshop Manual Gear Shift Lever Column Shift Removal and Installation WARNING: THE ELECTRICAL CIRCUIT FOR AIR BAG DEPLOYMENT IS POWERED DIRECTLY FROM THE BATTERY AND BACKUP POWER SUPPLY. TO AVOID ACCIDENTAL DEPLOYMENT AND POSSIBLE PERSONAL INJURY, THE BATTERY POSITIVE CABLE MUST BE DISCONNECTED FOR A MINIMUM OF ONE MINUTE BEFORE BEGINNING WORK TO DE-ENERGIZE THE BACKUP POWER SUPPLY. 1. Disconnect battery to starter relay cable (14300) and wait at least one minute for air bag backup power supply to discharge before beginning work. Refer to Section 01-20B. 2. Remove upper and lower steering column shrouds (3530) as outlined in this section. 3. Disconnect the overdrive on/off switch electrical connector. 4. Remove the selector lever boot.

29 file://c:\tso\tsocache\vdtom_5368\svk~us~en~file=svkb4a09.htm~gen~ref.htm Page 2 of 5 5. Use a small drift punch or suitable tool and drive the retaining pin from the steering column.

30 file://c:\tso\tsocache\vdtom_5368\svk~us~en~file=svkb4a09.htm~gen~ref.htm Page 3 of 5 6. Remove the gearshift lever (7210) from the steering column. 7. To install, reverse the removal procedure.

31 file://c:\tso\tsocache\vdtom_5368\svk~us~en~file=svkb4a09.htm~gen~ref.htm Page 4 of 5 Item Part Number Description 1 7G357 Gearshift Lever Pin Gearshift Lever Steering Column Opening Weather Seal 4 7C464 Clip Transmission Column Shift Selector Tube

32 file://c:\tso\tsocache\vdtom_5368\svk~us~en~file=svkb4a09.htm~gen~ref.htm Page 5 of 5

33 file://c:\tso\tsocache\vdtom_5368\svk~us~en~file=svkb4a10.htm~gen~ref.htm Page 1 of 1 Section 11-04A: Steering Column, Ranger REMOVAL AND INSTALLATION 1997 Ranger Workshop Manual Steering Shaft, Upper Removal and Installation To remove upper steering shaft, refer to Steering Column disassembly in this section.

34 file://c:\tso\tsocache\vdtom_5368\svk~us~en~file=svkb4a11.htm~gen~ref.htm Page 1 of 3 Section 11-04A: Steering Column, Ranger REMOVAL AND INSTALLATION 1997 Ranger Workshop Manual Steering Shaft, Intermediate Removal 1. CAUTION: Steering column should be in the locked position, or the lower end of the steering column is to be secured or wired in such a way as to prevent the steering column or steering wheel (3600) from rotating and damaging the air bag sliding contact (14A664). Remove the bolt securing the intermediate shaft and lower shaft, at the midpoint connection. Collapse the lower shaft. Discard original bolt. 2. Remove the bolt securing the intermediate shaft to the steering column assembly. Remove the intermediate shaft from inside the vehicle. Discard original bolt. 3. Remove the bolt securing the lower shaft to the steering gear input shaft. Remove lower shaft from vehicle. Installation 1. NOTE: Use new bolt to attach intermediate shaft to steering gear input shaft and steering column shaft to intermediate shaft. Install lower shaft on to the steering gear input (part of steering gear) shaft. Install new bolt and tighten bolt to Nm (30-40 lb-ft). 2. Install intermediate shaft through the steering column opening weather seal (3513) and onto the steering column assembly. Install new bolt and tighten to Nm (30-40 lb-ft). 3. Extend lower shaft and connect the upper shaft. Install and tighten bolt to Nm (30-40 lb-ft). Steering Column, Intermediate Shaft Installation

35 file://c:\tso\tsocache\vdtom_5368\svk~us~en~file=svkb4a11.htm~gen~ref.htm Page 2 of 3 Item Part Number Description 1 3C529 Steering Column 2 N S301 Bolt, M x B676 Steering Gear Intermediate Shaft Steering Column Opening Weather Seal Dash Panel 6 3A525 Steering Gear Lower Shaft 7 N S100 Bolt, M x 35 8 N S36MG Screw, M6-1 x F540 Steering Shaft U-Joint Shield Steering Gear (Power) Steering Gear (Manual) A Tighten to Nm (30-40 Lb-Ft) B Tighten to Nm (11-14 Lb-Ft)

36 file://c:\tso\tsocache\vdtom_5368\svk~us~en~file=svkb4a11.htm~gen~ref.htm Page 3 of 3

37 file://c:\tso\tsocache\vdtom_5368\svk~us~en~file=svkb4a12.htm~gen~ref.htm Page 1 of 10 Section 11-04A: Steering Column, Ranger REMOVAL AND INSTALLATION 1997 Ranger Workshop Manual Steering Column Lock Housing Bearing Upper Removal 1. Remove lock cylinder housing from steering column as described in this section. 2. Suitably support lock cylinder housing and tap out small steering column upper bearing with an appropriate drift and a plastic hammer. Installation 1. Suitably support lock cylinder housing. Position small steering column upper bearing so that the inner race is "up." Tap into place with a plastic hammer and a bushing driver installer or socket the same size as outer race of steering column bearing.

38 file://c:\tso\tsocache\vdtom_5368\svk~us~en~file=svkb4a12.htm~gen~ref.htm Page 2 of 10

39 file://c:\tso\tsocache\vdtom_5368\svk~us~en~file=svkb4a12.htm~gen~ref.htm Page 3 of Install lock cylinder housing on steering column tube (3514) as outlined. Intermediate Removal 1. Remove lock cylinder housing as described in this section. 2. Set lock cylinder housing flat on workbench and tap steering column bearing loose with suitable drift and a plastic hammer.

40 file://c:\tso\tsocache\vdtom_5368\svk~us~en~file=svkb4a12.htm~gen~ref.htm Page 4 of 10 Installation 1. Support lock cylinder housing on workbench. 2. Position steering column bearing so that the inner race will face up (inner race fully visible in up position), or out from lock cylinder housing, when installed.

41 file://c:\tso\tsocache\vdtom_5368\svk~us~en~file=svkb4a12.htm~gen~ref.htm Page 5 of Using a socket or bushing driver the same size as outer race of steering column bearing, tap steering column bearing into lock cylinder housing with a plastic hammer until fully seated.

42 file://c:\tso\tsocache\vdtom_5368\svk~us~en~file=svkb4a12.htm~gen~ref.htm Page 6 of 10 Lower Removal 1. Remove steering column lower bearing retainer (3D681) as outlined in this section.

43 file://c:\tso\tsocache\vdtom_5368\svk~us~en~file=svkb4a12.htm~gen~ref.htm Page 7 of Remove steering column lower bearing and steering column lower bearing sleeve from steering column lower bearing retainer by hand.

44 file://c:\tso\tsocache\vdtom_5368\svk~us~en~file=svkb4a12.htm~gen~ref.htm Page 8 of 10 Installation 1. Inspect flexible steering column lower bearing. Replace if damaged. 2. Position steering column lower bearing sleeve in steering column lower bearing retainer.

45 file://c:\tso\tsocache\vdtom_5368\svk~us~en~file=svkb4a12.htm~gen~ref.htm Page 9 of Press in assembled steering column lower bearing and steering column tube bearing sleeve with thumb pressure until seated. Inner race should face toward engine (inner race should be fully visible when bearing retainer is installed on steering column) when installed in the vehicle. 4. Install steering column lower bearing retainer on steering column as outlined in this section.

46 file://c:\tso\tsocache\vdtom_5368\svk~us~en~file=svkb4a12.htm~gen~ref.htm Page 10 of 10

47 file://c:\tso\tsocache\vdtom_5368\svk~us~en~file=svkb4a13.htm~gen~ref.htm Page 1 of 4 Section 11-04A: Steering Column, Ranger REMOVAL AND INSTALLATION 1997 Ranger Workshop Manual Bearing Retainer Lower Removal 1. Remove steering column as outlined in this section. 2. Using pliers, remove steering column lower bearing spring on tilt columns or bearing retainer (3C610) on fixed columns. Steering Column Lower Bearing Spring (Tilt Only) 3. Remove suspension height sensor control ring (3C131) (tilt only) and steering column lower bearing tolerance ring. Suspension Height Sensor Control Ring (Tilt Only)

48 file://c:\tso\tsocache\vdtom_5368\svk~us~en~file=svkb4a13.htm~gen~ref.htm Page 2 of 4 Item Part Number Description Steering Column Shaft (Tilt) 2 3E729 Steering Column Shaft (Fixed) 3 3L539 Steering Column Upper Bearing Tolerance Ring Steering Column Upper Bearing Spring 5 3C131 Suspension Height Sensor Control Ring 4. Remove three screws and steering column lower bearing retainer (3D681).

49 file://c:\tso\tsocache\vdtom_5368\svk~us~en~file=svkb4a13.htm~gen~ref.htm Page 3 of 4 5. For tilt column installation, reverse removal procedure. 6. For fixed column installation, compress upper shaft spring to allow bearing retainer to be seated in its grooves in the lower end of the steering shaft.

50 file://c:\tso\tsocache\vdtom_5368\svk~us~en~file=svkb4a13.htm~gen~ref.htm Page 4 of 4

51 file://c:\tso\tsocache\vdtom_5368\svk~us~en~file=svkb4a16.htm~gen~ref.htm Page 1 of 2 Section 11-04A: Steering Column, Ranger REMOVAL AND INSTALLATION 1997 Ranger Workshop Manual Support Brackets, Steering Column Bend Bracket To remove bend bracket, remove steering column lower bearing retainer (3D681) as outlined in this section, then remove bend bracket. The same screws secure the steering column lower bearing retainer and the bend bracket. Steering Column Lower Bearing Retainer and Bend Bracket

52 file://c:\tso\tsocache\vdtom_5368\svk~us~en~file=svkb4a16.htm~gen~ref.htm Page 2 of 2

53 file://c:\tso\tsocache\vdtom_5368\svk~us~en~file=svkb4a17.htm~gen~ref.htm Page 1 of 2 Section 11-04A: Steering Column, Ranger REMOVAL AND INSTALLATION 1997 Ranger Workshop Manual Tilt Wheel Handle and Shank Removal and Installation 1. To remove tilt wheel handle and shank (3F609), rotate the tilt wheel handle and shank counterclockwise. 2. To install, position tilt wheel handle and shank and rotate clockwise until tight.

54 file://c:\tso\tsocache\vdtom_5368\svk~us~en~file=svkb4a17.htm~gen~ref.htm Page 2 of 2

55 file://c:\tso\tsocache\vdtom_5368\svk~us~en~file=svkb4a18.htm~gen~ref.htm Page 1 of 4 Section 11-04A: Steering Column, Ranger REMOVAL AND INSTALLATION 1997 Ranger Workshop Manual Air Bag Sliding Contact Removal WARNING: THE ELECTRICAL CIRCUIT FOR AIR BAG DEPLOYMENT IS POWERED DIRECTLY FROM THE BATTERY AND BACKUP POWER SUPPLY. TO AVOID ACCIDENTAL DEPLOYMENT AND POSSIBLE PERSONAL INJURY, THE BATTERY POSITIVE CABLE MUST BE DISCONNECTED FOR A MINIMUM OF ONE MINUTE BEFORE BEGINNING WORK TO DE-ENERGIZE THE BACKUP POWER SUPPLY. 1. Make sure the vehicle's front wheels (1007) are facing straight ahead, and the steering wheel (3600) is oriented in the straight-ahead position. If the steering wheel is turned, the new air bag sliding contact (14A664) to be installed (which is locked in its shipping orientation) will not line up with the steering column casting and shaft. 2. Disconnect the battery to starter relay cable (14300). Wait at least one minute before proceeding, to allow the air bag backup power supply to discharge. 3. Remove steering wheel as described in this section. 4. Remove upper and lower steering column shrouds (3530) as described in this section. (Unscrew tilt lock lever to remove lower steering column shroud, if so equipped.) 5. Remove ignition switch lock cylinder as described in this section. Remove key warning chime contact from lock cylinder casting by pulling out. 6. Remove ground wire eyelet bolt (N805375) from steering column bend bracket hole. 7. Remove the two air bag sliding contact down lead wire harness hanger clips from the steering column casting. 8. Disconnect the two air bag sliding contact lower wire harness electrical connectors from the instrument panel wiring harness at the steering column bend bracket, and remove connectors from bend bracket (remove ground wire eyelet bolt N805375). 9. Remove the air bag sliding contact from the steering column by prying the three snaps back from the small ramps on the steering column lock cylinder housing as the air bag sliding contact is pulled away from the housing. The snaps are located at the 12 o'clock, 3 o'clock, and 6 o'clock positions on the back of the air bag sliding contact.

56 file://c:\tso\tsocache\vdtom_5368\svk~us~en~file=svkb4a18.htm~gen~ref.htm Page 2 of 4 Installation 1. Make sure the vehicle's front wheels are straight ahead and the steering column shaft alignment mark (punch mark on end of shaft) is at the 12 o'clock position. 2. If a new air bag sliding contact is being installed, orient the air bag sliding contact prior to installation by depressing the yellow hub lock with your finger and rotating the white hub approximately 1/4 turn clockwise until the arrow lines up with the shaft lock (yellow loop). Release hub lock. 3. If a new air bag sliding contact is being installed, position the new air bag sliding contact with the shaft lock (yellow loop) at the top, and slide the new air bag sliding contact onto the steering column shaft. (If the old air bag sliding contact is being reinstalled, position the black housing so that the three pins on the back side lineup with the three holes in the steering column lock cylinder housing at 12 o'clock, 3 o'clock, and 6 o'clock.) Push the air bag sliding contact firmly until the three guide pins on the back of the air bag sliding contact engage the holes in the steering column lock cylinder housing, and the three snaps on the back of the air bag sliding contact engage the three ramps on the steering column lock cylinder housing. 4. Push the two wire hanger clips into the steering column casting. 5. Install the down lead harness wire connectors in the original locations on the steering column lower bend bracket and connect to the instrument panel wiring harness. 6. Route the ground wire from the air bag sliding contact lower 6-pin wiring connector to the steering column bend bracket hole, and secure the eyelet to the bend bracket with bolt (N805375).

57 file://c:\tso\tsocache\vdtom_5368\svk~us~en~file=svkb4a18.htm~gen~ref.htm Page 3 of 4 7. Install the key warning chime wire (first remove black protective cover from the connector) into the key lock cylinder by pushing firmly until it snaps into place. 8. Reinstall the upper and lower steering column shrouds. Reinstall tilt lever. 9. Reinstall the steering wheel as outlined in this section. Connect steering wheel wiring connector to air bag sliding contact. 10. Unlock the air bag sliding contact by pulling up on the yellow loop at the top of the air bag sliding contact to remove. 11. Connect driver air bag to air bag sliding contact connector. Place driver side air bag module (043B13) into steering wheel and install air bag retaining bolts. Hold driver side air bag module in position in steering wheel while bolts are being tightened to ensure proper fit. 12. Reinstall two steering wheel cover plugs by snapping into holes on sides of steering wheel. 13. NOTE: When the battery (10655) has been disconnected and reconnected, some abnormal drive symptoms may occur while the powertrain control module (PCM) (12A650) relearns its adaptive strategy. The vehicle may need to be driven to relearn the strategy. Connect battery to starter relay cable. Refer to Section 01-20B. 14. Verify air bag warning indicator operation. Steering Wheel with Air Bag Item Part Number Description 1 043B13 Driver Side Air Bag Module 2 N S100 Torx Head Screw, M x Steering Wheel 4 14A664 Air Bag Sliding Contact 5 3C529 Steering Column

58 file://c:\tso\tsocache\vdtom_5368\svk~us~en~file=svkb4a18.htm~gen~ref.htm Page 4 of 4 6 Clip (Part of 14A664) 7 3F785 Plug 8 N S424 Bolt 9 N S36MG Bolt A Tighten to Nm (25-33 Lb-Ft) B Tighten to Nm (67-92 Lb-In) C Tighten to Nm ( Lb-Ft)

59 file://c:\tso\tsocache\vdtom_5368\svk~us~en~file=svkb4a19.htm~gen~ref.htm Page 1 of 4 Section 11-04A: Steering Column, Ranger REMOVAL AND INSTALLATION 1997 Ranger Workshop Manual Ignition Switch Lock Cylinder NOTE: The following procedure applies to vehicles that have functional lock cylinders and keys. If key numbers are known, the proper key can be made. Lock Cylinder Functional Removal 1. Disconnect battery ground cable (14301). 2. Turn lock cylinder key to RUN position. 3. Remove lower shroud as outlined in this section under shroud removal. 4. Place a 3.17mm (1/8-inch) diameter wire pin or small drift punch in hole in steering column under lock cylinder. Depress retaining pin while pulling out on lock cylinder to remove it from housing of steering column.

60 file://c:\tso\tsocache\vdtom_5368\svk~us~en~file=svkb4a19.htm~gen~ref.htm Page 2 of 4 Installation 1. Install lock cylinder by turning it to RUN position and depressing retaining pin. Insert lock cylinder into steering column housing. Make sure ignition switch lock cylinder is fully seated and aligned in interlocking washer before turning key to OFF position. This will permit retaining pin of ignition lock cylinder to extend into hole of steering column. 2. Rotate lock cylinder, using key, to make sure of correct mechanical operation in all positions. 3. NOTE: When the battery (10655) has been disconnected and reconnected, some abnormal drive symptoms may occur while the powertrain control module (PCM) (12A650) relearns its adaptive strategy. The vehicle may need to be driven 16 km (10 miles) or more for powertrain control module to relearn the strategy. Connect battery ground cable. Lock Cylinder Non-Functional Removal NOTE: The following procedure applies to vehicles in which the ignition lock is inoperative and the ignition switch lock cylinder (11582) cannot be rotated due to a lost or broken key, unknown key number, or a cap that has been damaged or broken to the extent that the ignition switch lock cylinder cannot be rotated.

61 file://c:\tso\tsocache\vdtom_5368\svk~us~en~file=svkb4a19.htm~gen~ref.htm Page 3 of 4 1. Disconnect battery ground cable. 2. Using channel lock or vise grip pliers, twist cap until it separates from the ignition switch lock cylinder. 3. Remove lower shroud as outlined in this section under shroud removal. 4. Prick-punch pin and drill out with 1/8-inch bit. Do not drill deeper than 13mm (1/2 inch). Put a piece of masking tape 13mm (1/2 inch) from tip on bit. Take care not to damage housing. 5. Using a 3/8-inch diameter drill, drill down middle of ignition lock key slot approximately 44mm (1-3/4 inch) until ignition switch lock cylinder breaks loose from breakaway base of ignition switch lock cylinder. Remove ignition switch lock cylinder and drill shavings from lock cylinder housing. 6. Remove column lock gear retainer, steering column lock housing bearing (3E700) and steering column lock gear (3E717). Thoroughly clean all drill shavings and other foreign materials from lock cylinder housing. 7. Carefully inspect lock cylinder housing for damage from the above operation. If damage is apparent, lock cylinder housing must be replaced. Installation 1. Replace lock cylinder housing, if damaged. 2. Install steering column lock gear, steering column lock housing bearing and column lock gear retainer. 3. Install trim and electrical parts. 4. Install new ignition switch lock cylinder as described in this section. 5. NOTE: When the battery has been disconnected and reconnected, some abnormal drive symptoms may occur while the powertrain control module relearns its adaptive strategy. The vehicle may need to be driven 16 km (10 miles) or more to relearn the strategy. Connect battery ground cable. 6. Check operation of lock cylinder.

62 file://c:\tso\tsocache\vdtom_5368\svk~us~en~file=svkb4a19.htm~gen~ref.htm Page 4 of 4

63 file://c:\tso\tsocache\vdtom_5368\svk~us~en~file=svkb4a21.htm~gen~ref.htm Page 1 of 5 Section 11-04A: Steering Column, Ranger REMOVAL AND INSTALLATION 1997 Ranger Workshop Manual Ignition Lock Drive Gear Removal 1. CAUTION: Carefully note the position of the column lock gear retainer prior to removal. Rotate ignition switch lock cylinder (11582) to RUN position. Using a 1/8-inch drift, press lock cylinder retaining pin through access hole and remove ignition switch lock cylinder. 2. Remove column lock gear retainer by inserting a screwdriver or similar tool, with a 90 degree bend on the tip, between steering column upper bearing retainer and steering column lock housing bearing (3E700) and by prying upward. 3. Insert tip of a screwdriver into Double-D slot of steering column lock housing bearing, then rotate 90 degrees. Remove steering column lock housing bearing.

64 file://c:\tso\tsocache\vdtom_5368\svk~us~en~file=svkb4a21.htm~gen~ref.htm Page 2 of 5 4. Remove steering column lock gear (3E717). Carefully note relationship of steering column lock gear to position of rack teeth.

65 file://c:\tso\tsocache\vdtom_5368\svk~us~en~file=svkb4a21.htm~gen~ref.htm Page 3 of 5 Installation 1. Position steering column lock gear in base of lock cylinder housing in the same position as that noted during removal procedure. The position of steering column lock gear is correct if last tooth on steering column lock gear is meshed with last tooth on steering column lock lever actuator (3E715). 2. Position bearing retainer (3C610) in lock cylinder housing. Insert tip of a screwdriver into Double-D slot of steering column lock housing bearing, then rotate 90 degrees. 3. Press blue plastic column lock gear retainer into steering column lock cylinder housing. Make sure column lock gear retainer is in its original position. 4. Line up flats of steering column lock gear with flats of washer by pulling down on the steering column lock lever actuator. 5. Install ignition switch lock cylinder. 6. Check for proper start in Park and Neutral. Also, check to make sure start circuit cannot be actuated in Drive or Reverse positions and the steering column tube is locked in Lock position.

66 file://c:\tso\tsocache\vdtom_5368\svk~us~en~file=svkb4a21.htm~gen~ref.htm Page 4 of 5

67 file://c:\tso\tsocache\vdtom_5368\svk~us~en~file=svkb4a21.htm~gen~ref.htm Page 5 of 5

68 file://c:\tso\tsocache\vdtom_5368\svk~us~en~file=svkb4a23.htm~gen~ref.htm Page 1 of 3 Section 11-04A: Steering Column, Ranger REMOVAL AND INSTALLATION 1997 Ranger Workshop Manual Brake Shift Interlock Solenoid Removal and Installation 1. Remove steering column as outlined in this section. 2. NOTE: Brake shift interlock solenoid is retained to the transmission shift selector position insert (7A216) with a pushnut. Remove three screws attaching brake shift interlock solenoid and transmission shift selector position insert. Brake Shift Interlock Solenoid Retainer Screws 3. Remove brake shift interlock solenoid and transmission shift selector position insert. Brake Shift Interlock Solenoid

69 file://c:\tso\tsocache\vdtom_5368\svk~us~en~file=svkb4a23.htm~gen~ref.htm Page 2 of 3 4. If necessary, remove pushnut and separate brake shift interlock solenoid from transmission shift selector position insert. To install, reverse removal procedures. Tighten attaching screws to 7-11 Nm (62-97 lb-in).

70 file://c:\tso\tsocache\vdtom_5368\svk~us~en~file=svkb4a23.htm~gen~ref.htm Page 3 of 3

71 file://c:\tso\tsocache\vdtom_5368\svk~us~en~file=svkb4a24.htm~gen~ref.htm Page 1 of 7 Section 11-04A: Steering Column, Ranger REMOVAL AND INSTALLATION 1997 Ranger Workshop Manual Steering Column Shroud Lower Removal 1. Disconnect battery ground cable (14301). 2. Remove two screws and instrument panel steering column cover (04459). 3. Remove three screws and instrument panel steering column cover reinforcement. Instrument Panel Steering Column Cover and Reinforcement Item Part Number Instrument Panel Description 2 044C86 Instrument Panel Steering Column Opening Center Reinforcement 3 N S58 4 N S36 Nuts Screw 5 N Screw

72 file://c:\tso\tsocache\vdtom_5368\svk~us~en~file=svkb4a24.htm~gen~ref.htm Page 2 of 7 S D82 Instrument Panel Access Hole Cover Instrument Panel Steering Column Cover 8 017A28 Instrument Panel Reinforcement A Tighten to Nm ( Lb-In) B Tighten to Nm ( Lb-In) C Tighten to Nm (19-25 Lb-In) 4. Unscrew and remove tilt wheel handle and shank (3F609), if equipped. 5. Remove retaining screws and lower steering column shroud (3530). Steering Column Installation Item Part Number Description Instrument Panel Reinforcement Steering Column Shroud (Upper) Gearshift Lever 4 3C529 Steering Column 5 3F609 Tilt Wheel Handle and Shank S2 Screw Steering Column Shroud (Lower)

73 file://c:\tso\tsocache\vdtom_5368\svk~us~en~file=svkb4a24.htm~gen~ref.htm Page 3 of 7 8 N S58 Nut 9 7E395 Shift Cable and Bracket A Tighten to Nm ( Lb-In) B Tighten to Nm (10-12 Lb-Ft) Installation 1. Position lower steering column shroud into place on upper steering column shroud. 2. Install retaining screws and tighten to Nm (7-9 lb-in). 3. Install tilt wheel handle and shank, if equipped with tilt wheel. 4. Install instrument panel steering column cover reinforcement and retaining screws. Tighten screws to Nm ( lb-in). 5. Install instrument panel steering column cover and two screws. Tighten to Nm (19-25 lb-in). 6. NOTE: When the battery (10655) has been disconnected and reconnected, some abnormal drive symptoms may occur while the powertrain control module (PCM) (12A650) relearns its adaptive strategy. The vehicle may need to be driven 16 km (10 miles) or more to relearn the strategy. Reconnect battery ground cable. Upper Removal and Installation 1. Remove lower steering column shroud as outlined above. 2. Turn ignition switch lock cylinder (11582) to RUN position. 3. Using flat-tipped punch, push on button below ignition switch lock cylinder and pull out ignition switch lock cylinder.

74 file://c:\tso\tsocache\vdtom_5368\svk~us~en~file=svkb4a24.htm~gen~ref.htm Page 4 of 7 4. Pull off knob (18519). 5. Using wide-blade screwdriver, pry loose left-hand instrument panel finish panel (04338). Twist 45 degrees and remove headlamp switch electrical connector from instrument panel finish panel.

75 file://c:\tso\tsocache\vdtom_5368\svk~us~en~file=svkb4a24.htm~gen~ref.htm Page 5 of 7 6. Remove retaining screws securing instrument panel lower center finish panel. 7. Using wide-blade screwdriver, pry loose instrument panel lower center finish panel. Pull lower finish panel away from instrument panel assembly.

76 file://c:\tso\tsocache\vdtom_5368\svk~us~en~file=svkb4a24.htm~gen~ref.htm Page 6 of 7 8. Remove two screws securing lower instrument panel opening finish panel. Pry panel loose. Hold instrument panel finish panel (044D70) while prying loose right side of lower instrument panel finish panel. Remove finish panel. 9. Remove upper steering column shroud.

77 file://c:\tso\tsocache\vdtom_5368\svk~us~en~file=svkb4a24.htm~gen~ref.htm Page 7 of To install, reverse removal procedure. Ignition switch lock cylinder simply pushes back in. Tighten instrument panel finish panel screws to Nm (19-25 lb-in).

78 file://c:\tso\tsocache\vdtom_5368\svk~us~en~file=svkb4a25.htm~gen~ref.htm Page 1 of 3 Section 11-04A: Steering Column, Ranger REMOVAL AND INSTALLATION 1997 Ranger Workshop Manual Turn Signal Cancel Cam Service Removal 1. Remove steering wheel (3600) as outlined in this section. 2. Remove air bag sliding contact (14A664) as outlined in this section. 3. Unplug multi-function switch (13K359). 4. Remove two screws and multi-function switch. 5. Using screwdriver, pry loose turn indicator cancel cam (13318) and remove. Turn Indicator Cancel Cam Removal Installation 1. Push on turn indicator cancel cam with flush surface "up." 2. Install multi-function switch and tighten screws to Nm (19-25 lb-in). 3. Plug in multi-function switch. 4. Install air bag sliding contact. 5. Install steering wheel as outlined in this section.

79 file://c:\tso\tsocache\vdtom_5368\svk~us~en~file=svkb4a25.htm~gen~ref.htm Page 2 of 3

80 file://c:\tso\tsocache\vdtom_5368\svk~us~en~file=svkb4a25.htm~gen~ref.htm Page 3 of 3

81 file://c:\tso\tsocache\vdtom_5368\svk~us~en~file=svkb4a26.htm~gen~ref.htm Page 1 of 37 Section 11-04A: Steering Column, Ranger DISASSEMBLY AND ASSEMBLY 1997 Ranger Workshop Manual Steering Column Disassembly 1. Remove instrument panel cover and reinforcement from vehicle as described in this section. 2. Unscrew and remove tilt wheel handle and shank (3F609), if equipped. 3. Remove three screws and lower steering column shroud (3530). 4. Turn ignition switch lock cylinder (11582) to RUN position. 5. Using flat-tipped punch, push on button below ignition switch lock cylinder and pull out ignition switch lock cylinder.

82 file://c:\tso\tsocache\vdtom_5368\svk~us~en~file=svkb4a26.htm~gen~ref.htm Page 2 of Remove upper steering column shroud. 7. CAUTION: Be sure air bag sliding contact internal lock is engaged. Hub should not turn more then 45 degrees in either direction. Using door trim removal tool, remove air bag sliding contact electrical connectors from bend bracket. 8. CAUTION: Do not remove wire harness clips from wire bundle. Using door trim removal tool, disconnect two wire harness clips from steering column. 9. Remove key warning chime contact and anti-theft contact from ignition lock cylinder pocket of lock cylinder housing. Steering Wheel with Air Bag

83 file://c:\tso\tsocache\vdtom_5368\svk~us~en~file=svkb4a26.htm~gen~ref.htm Page 3 of 37 Item Part Number Description 1 043B13 Driver Side Air Bag Module 2 N S100 Torx Head Screw, M x Steering Wheel 4 14A664 Air Bag Sliding Contact 5 3C529 Steering Column 6 Clip (Part of 14A664) 7 3F785 Plug 8 N S424 Bolt 9 N S36MG Bolt A Tighten to Nm (25-33 Lb-Ft) B Tighten to Nm (67-92 Lb-In) C Tighten to Nm ( Lb-Ft) 10. Remove air bag sliding contact (14A664) by pushing snap back at 6 o'clock position, then 3 o'clock position, then 12 o'clock position and remove from steering shaft.

84 file://c:\tso\tsocache\vdtom_5368\svk~us~en~file=svkb4a26.htm~gen~ref.htm Page 4 of 37 Steering Column Item Part Number Description 1 3C131 Suspension Height Sensor Control Ring Transmission Selector Lever Arm and Support

85 file://c:\tso\tsocache\vdtom_5368\svk~us~en~file=svkb4a26.htm~gen~ref.htm Page 5 of D681 Steering Column Lower Bearing Retainer 4 7A216 Transmission Shift Selector Position Insert 5 Attachment Point (Part of 7302) Transmission Column Shift Selector Tube Steering Column Lock Cylinder Housing Turn Indicator Cancel Cam Steering Column Upper Bearing Spring 10 3Z719 Brake Shift Interlock Solenoid Steering Column Bend Bracket Steering Column Bearing Spring (Tilt Only) 11. Remove turn indicator cancel cam (13318) by pushing up with flat-bladed screwdriver. Note direction of flush surface. Turn Indicator Cancel Cam Removal 12. Remove ignition switch. Ignition Switch Removal

86 file://c:\tso\tsocache\vdtom_5368\svk~us~en~file=svkb4a26.htm~gen~ref.htm Page 6 of Remove upper bearing retainer snap ring and steering column upper bearing spring (3520). Steering Column Upper Bearing Spring and Upper Bearing Retainer 14. Remove steering column bearing sleeve (3518) and steering column bearing tolerance ring (3L539). 15. Remove gearshift lever (7210). 16. NOTE: Brake shift interlock solenoid is retained to the transmission shift selector position insert (7A216) with a pushnut. Remove three screws attaching brake shift interlock solenoid and transmission shift selector position insert. Brake Shift Interlock Solenoid Screws

87 file://c:\tso\tsocache\vdtom_5368\svk~us~en~file=svkb4a26.htm~gen~ref.htm Page 7 of Remove brake shift interlock solenoid and transmission shift selector position insert together. Transmission Shift Selector Position Insert 18. If necessary, remove pushnut and separate brake shift interlock solenoid and transmission shift selector position insert.

88 file://c:\tso\tsocache\vdtom_5368\svk~us~en~file=svkb4a26.htm~gen~ref.htm Page 8 of Remove two screws and transmission control selector arm. Transmission Selector Lever Arm 20. Remove four screws, two gearshift tube bushing clamps (7E400), transmission column shift selector tube (7212) and assembled parts.

89 file://c:\tso\tsocache\vdtom_5368\svk~us~en~file=svkb4a26.htm~gen~ref.htm Page 9 of Pry on end of steering column lock lever pin (3B663) which is sticking out.

Steering Column. Disassembly. 1. Remove instrument panel cover and reinforcement from vehicle as described in this section.

Steering Column. Disassembly. 1. Remove instrument panel cover and reinforcement from vehicle as described in this section. Page 1 of 14 Section 11-04A: Steering Column, Ranger 1997 Aerostar/Ranger Workshop Manual DISASSEMBLY AND ASSEMBLY Procedure revision date: 05/17/2000 Steering Column Disassembly 1. Remove instrument panel

More information

REMOVAL AND INSTALLATION Procedure revision date: 05/17/2000

REMOVAL AND INSTALLATION Procedure revision date: 05/17/2000 1997 Aerostar/Ranger REMOVAL AND INSTALLATION Procedure revision date: 05/17/2000 Module, Driver Side Air Bag NOTE: In general, if the air bag did not deploy in an accident, it was not needed. Complete

More information

1989 Jeep Cherokee. STEERING COLUMN' '1989 STEERING Jeep Steering Columns STEERING COLUMN STEERING Jeep Steering Columns

1989 Jeep Cherokee. STEERING COLUMN' '1989 STEERING Jeep Steering Columns STEERING COLUMN STEERING Jeep Steering Columns STEERING COLUMN 1989 STEERING Jeep Steering Columns DESCRIPTION All models use collapsible steering columns. All columns have integral ignition switch and locking device. Optional tilt wheel is available

More information

1995 Mercury Grand Marquis GS

1995 Mercury Grand Marquis GS AIR BAG SYSTEM CAUTION: Read the following safety precautions BEFORE servicing steering columns on vehicles equipped with air bag restraint system. ALWAYS wear safety glasses when servicing vehicle with

More information

REMOVAL & INSTALLATION

REMOVAL & INSTALLATION REMOVAL & INSTALLATION Removal 1. Center steering wheel. Disconnect negative battery cable. Remove steering coupling shield (if equipped). Disconnect steering shaft at flexible coupling or pot joint. Note

More information

1999 Explorer/Mountaineer Workshop Manual

1999 Explorer/Mountaineer Workshop Manual Page 1 of 16 SECTION 211-04: Steering Column 1999 Explorer/Mountaineer Workshop Manual DISASSEMBLY AND ASSEMBLY Procedure revision date: 07/27/1998 Steering Column Automatic Transmission Disassembly WARNING:

More information

1995 Town Car/Crown Victoria/Grand Marquis

1995 Town Car/Crown Victoria/Grand Marquis Page 1 of 23 Section 11-04: Steering Column DISASSEMBLY AND ASSEMBLY 1995 Town Car, Crown Victoria, Grand Marquis Workshop Manual Steering Column Disassembly 1. Disconnect battery ground cable (14301)

More information

1994 Ford Pickup F250. STEERING COLUMN - EXCEPT STRIPPED CHASSIS 1994 STEERING Ford Motor Co. - Steering Columns - Except Stripped Chassis

1994 Ford Pickup F250. STEERING COLUMN - EXCEPT STRIPPED CHASSIS 1994 STEERING Ford Motor Co. - Steering Columns - Except Stripped Chassis STEERING COLUMN - EXCEPT STRIPPED CHASSIS 1994 STEERING Ford Motor Co. - Steering Columns - Except DESCRIPTION NOTE: Unless otherwise specified, references to Pickup include the F350 Super Duty commercial

More information

STEERING COLUMN SWITCHES

STEERING COLUMN SWITCHES STEERING COLUMN SWITCHES 1998 Pontiac Bonneville 1998 ACCESSORIES & EQUIPMENT General Motors Corp. - Steering Column Switches Buick; LeSabre Oldsmobile; Eighty Eight, LSS & Regency Pontiac; Bonneville

More information

STEERING COLUMN - TILT

STEERING COLUMN - TILT STEERING COLUMN - TILT 1994 Toyota Celica 1994 STEERING Toyota - Steering Column - Tilt Wheel Celica DESCRIPTION & OPERATION Tilt steering wheels incorporate a mainshaft, attached by a "U" joint to an

More information

STEERING COLUMN - STANDARD

STEERING COLUMN - STANDARD STEERING COLUMN - STANDARD 1994 Toyota Celica 1994 STEERING Toyota - Steering Column - Standard Celica DESCRIPTION & OPERATION Steering column is a collapsible 2-piece design. Columns use shear pins to

More information

STEERING COLUMN - TILT

STEERING COLUMN - TILT STEERING COLUMN - TILT 1993 Toyota Celica 1993 STEERING Toyota - Steering Columns - Tilt Wheel Celica DESCRIPTION & OPERATION Tilt steering wheels incorporate an upper steering shaft, attached by a "U"

More information

Installation Instructions Z-Gate Shifter

Installation Instructions Z-Gate Shifter Installation Instructions Z-Gate Shifter Part Number 80681 1998, 2001 by B&M Racing and Performance Products The B&M Z-Gate shifter can be used in vehicles equipped with most popular three speed automatic

More information

Installation Instructions. QuickSilver Shifter. Fits: GM, Ford, Chrysler Transmissions See Application Guide for Specific Applications Part # 80683

Installation Instructions. QuickSilver Shifter. Fits: GM, Ford, Chrysler Transmissions See Application Guide for Specific Applications Part # 80683 Installation Instructions QuickSilver Shifter Fits: GM, Ford, Chrysler Transmissions See Application Guide for Specific Applications Part # 80683 WORK SAFELY! For maximum safety, perform this installation

More information

1997 Mazda MX-5 Miata. STEERING COLUMN STEERING Mazda Motors Corp. - Steering Columns STEERING Mazda Motors Corp. - Steering Columns

1997 Mazda MX-5 Miata. STEERING COLUMN STEERING Mazda Motors Corp. - Steering Columns STEERING Mazda Motors Corp. - Steering Columns Disable air bag system before servicing any air bag system or steering column component. See AIR BAG DISABLING & ACTIVATING. After disabling air bag system, wait at least one minute before servicing. Air

More information

STEERING COLUMN SWITCHES

STEERING COLUMN SWITCHES STEERING COLUMN SWITCHES 1990 Nissan 240SX TESTING 1990 ACCESSORIES & EQUIPMENT Nissan - Steering Column Switches Axxess, Maxima, Pathfinder, Pickup, Pulsar NX, Sentra, Stanza, 240SX, 300ZX * PLEASE READ

More information

Stealth Pro Ratchet Shifter

Stealth Pro Ratchet Shifter Installation Instructions Stealth Pro Ratchet Shifter Part Number 81120 & 81121 (see www.bmracing.com for the latest technical product information) 2010, 2006 by B&M Racing and Performance Products The

More information

The drawings are all available from the author or from the host websight. You will find these pictures and descriptions to be most helpful.

The drawings are all available from the author or from the host websight. You will find these pictures and descriptions to be most helpful. Last Revision: 10JA2010 1969 THRU 1976 GM A & F-CAR STANDARD (NON-ADJUSTABLE) STEERING COLUMN DISASSEMBLY & REPAIR INSTRUCTIONS PAPER #1 Disassembly and Repair Instructions Addressed in this Paper Degree

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS INSTALLATION INSTRUCTIONS Accessory TRIM Application 2009 ACCORD 4-DOOR Publications No. AII 40008 Issue Date JULY 2008 PARTS LIST Steering Wheel Trim (Without Navigation) P/N 08Z13-TA0-100 Right steering

More information

ARTICLE BEGINNING DESCRIPTION DISABLING & ACTIVATING AIR BAG SYSTEM SERVICE PRECAUTIONS STEERING Volkswagen - Steering Columns.

ARTICLE BEGINNING DESCRIPTION DISABLING & ACTIVATING AIR BAG SYSTEM SERVICE PRECAUTIONS STEERING Volkswagen - Steering Columns. Article Text ARTICLE BEGINNING 1995-96 STEERING Volkswagen - Steering Columns Golf III WARNING: All models are equipped with a Supplemental Restraint System (SRS) that includes an air bag located in steering

More information

PRO RATCHET UNIVERSAL SHIFTER

PRO RATCHET UNIVERSAL SHIFTER Installation Instructions PRO RATCHET UNIVERSAL SHIFTER Fits: GM, Ford and Chryslers w/automatic Transmission See Application Guide for Specific Vehicles Catalog # 80842 WORK SAFELY! For maximum safety,

More information

Z-Gate Universal Shifter

Z-Gate Universal Shifter Installation Instructions Z-Gate Universal Shifter Fits: GM, Ford, Lincoln and Chrysler Transmissions See Application Guide for Specific Applications Part #80681 Rev 06/01/2018 WORK SAFELY! For maximum

More information

J2 Remove sound insulation/knee guard 1 and side panel 2 on center console

J2 Remove sound insulation/knee guard 1 and side panel 2 on center console J1 Preparations Drive car forward on a level surface so that wheels are straight. Disconnect battery negative lead. Turn ignition key to position 1 so that steering lock is off. J2 Remove sound insulation/knee

More information

1997 Thunderbird/Cougar

1997 Thunderbird/Cougar Page 1 of 7 Section 11-04: Steering Column 1997 Thunderbird/Cougar Workshop Manual DISASSEMBLY AND ASSEMBLY Procedure revision date: 05/16/2000 Steering Column Disassembly CAUTION: Do not remove the steering

More information

Installation Instructions Sport Shifter

Installation Instructions Sport Shifter The B&M Sport Shifter can be used in vehicles equipped with most popular three speed or four speed automatic transmissions. It is equipped with neutral safety and backup light switches, transmission brackets

More information

2004 Lexus LS430. Submodel: Engine Type: V8 Liters: 4.3 Fuel Delivery: FI Fuel: GAS

2004 Lexus LS430. Submodel: Engine Type: V8 Liters: 4.3 Fuel Delivery: FI Fuel: GAS 2004 Lexus LS430 Submodel: Engine Type: V8 Liters: 4.3 Fuel Delivery: FI Fuel: GAS OVERHAUL If the airbag connector is disconnected with the ignition switch in the ON position, DTCs will be recorded. When

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS INSTALLATION INSTRUCTIONS Accessory Application Publications No. BII 23302 2002 MDX Issue Date PN 08U97-S3V-210 (BLACK) P/N 08U97-S3V-270 (SADDLE) NOV 2001 PARTS LIST Wood trim steering wheel 1. Make sure

More information

Installation Instructions Right Hand Drive Megashifter

Installation Instructions Right Hand Drive Megashifter Installation Instructions Right Hand Drive Megashifter Part Number 80685 1995, 2001, 2006, 2010 by B&M Racing & Performance Products The B&M Right Hand Drive Megashifter is designed specifically for vehicles

More information

Hurst VMATIC3 INSTALLATION

Hurst VMATIC3 INSTALLATION FORM 159 8530 07/12 Hurst VMATIC3 3-Speed & 4-Speed Automatic Shifter Catalog #3838530 2012 by Hurst Performance The Hurst Vmatic3 shifter can be used in vehicles equipped with most popular three speed

More information

Installation Instructions Megashifter

Installation Instructions Megashifter Installation Instructions Megashifter The B&M Megashifter shifter can be used in vehicles equipped with most popular three speed or four speed automatic transmissions. Your B&M Megashifter comes equipped

More information

Light Truck MegaShifter

Light Truck MegaShifter Installation Instructions Light Truck MegaShifter The B&M Light Truck Megashifter shifter is designed to be used in most light trucks equipped with most popular three speed or four speed automatic transmissions.

More information

TCI FastGate Shifter Installation Instructions

TCI FastGate Shifter Installation Instructions 151 INDUSTRIAL DRIVE ASHLAND, MISSISSIPPI 38603 http://www.tciauto.com TELEPHONE: 662-224-8972 FAX LINE: 662-224-8255 E-MAIL: tech@tciauto.com TCI 616541 FastGate Shifter Installation Instructions The

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS INSTALLATION INSTRUCTIONS Accessory Application Publications No. BII 24570 P/N 08U97-S3V-210A (BLACK) P/N 08U97-S3V-220A(SADDLE) 2003 MDX Issue Date OCT 2002 PARTS LIST Wood steering wheel 1. Make sure

More information

The drawings are all available from the author or from the host websight. You will find these pictures and descriptions to be most helpful.

The drawings are all available from the author or from the host websight. You will find these pictures and descriptions to be most helpful. Last Revision: 09JA2010 1969 THROUGH 1976 GM A & F-CAR TILT STEERING COLUMN DISASSEMBLY & REPAIR INSTRUCTIONS PAPER #1 Disassembly and Repair Instructions Addressed in this Paper Degree of Difficulty Page

More information

The drawings are all available from the author or from the host websight.

The drawings are all available from the author or from the host websight. Last Revision: 15OC2013 1969 THRU 1979 CORVETTE C3 STANDARD (NON-ADJUSTABLE) STEERING COLUMN DISASSEMBLY & REPAIR INSTRUCTIONS PAPER #1 Disassembly and Repair Instructions Addressed in this Paper Difficulty

More information

Installation Instructions Street Bandit Shifter

Installation Instructions Street Bandit Shifter Installation Instructions Street Bandit Shifter Part Number 80797 (see www.bmracing.com for the latest technical product information) 2006, 2000 by B&M Racing and Performance Products The B&M Street Bandit

More information

Installation Instructions StarShifter

Installation Instructions StarShifter Installation Instructions StarShifter Part Number 80675 2000 by B&M Racing & Performance Products LLC The B&M StarShifter can be used in vehicles equipped with most popular three speed automatic transmissions.

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS INSTALLATION INSTRUCTIONS Accessory Application Publications No. BII 25831-26975 P/N 08U97-S3V-210A (BLACK) P/N 08U97-S3V-220A(SADDLE) 2004 MDX Issue Date MARCH 2004 PARTS LIST Wood steering wheel 1. Make

More information

SUBJECT: While In Bi-level Mode, Air Flow From Panel Vents Is Less Than That Of The Floor Vents

SUBJECT: While In Bi-level Mode, Air Flow From Panel Vents Is Less Than That Of The Floor Vents NUMBER: GROUP: 24-20-99 Rev. A Heating & A/C DATE: Dec. 17, 1999 This bulletin is supplied as technical information only and is not an authorization for repair. No part of this publication may be reproduced,

More information

ALLDATA Online Dodge Truck RAM 1500 Truck 2WD V6-3.7L VIN K - Steeri... Steering Column

ALLDATA Online Dodge Truck RAM 1500 Truck 2WD V6-3.7L VIN K - Steeri... Steering Column Page 1 of 5 Home Account Contact ALLDATA Log Out Help PAUL REDEHOFT Select Vehicle New TSBs Technician's Reference Component Search: OK 2002 Dodge Truck RAM 1500 Truck 2WD V6-3.7L VIN K Conversion Calculator

More information

2. NOTE: On vehicles equipped with automatic transmissions, move the shift lever to the 1 position to ease removal.

2. NOTE: On vehicles equipped with automatic transmissions, move the shift lever to the 1 position to ease removal. Page 1 of 28 Section 501-12: Instrument Panel and Console REMOVAL AND INSTALLATION 1997 F-150, F-250 Workshop Manual Instrument Panel Removal 1. WARNING: TO AVOID ACCIDENTAL DEPLOYMENT AND POSSIBLE INJURY,

More information

GENUINE PARTS INSTALLATION INSTRUCTIONS

GENUINE PARTS INSTALLATION INSTRUCTIONS GENUINE PARTS INSTALLATION INSTRUCTIONS 1 DESCRIPTION: 2 APPLICATION: 3 PART NUMBER(S) REQUIRED FOR INSTALLATION: Fog Lamp Kit (AL) Rogue (SV) 999F1 G2000 (Fog Lamp Kit) 4 KIT CONTENTS: Item Qty. Part

More information

Technical Support (707)

Technical Support (707) Installation Instructions CONSOLE MEGASHIFTER Fits: 1982-1992 Camaro & Firebird w/automatic Transmission *except 1988-1992 Firebird Formula Model Catalog # 80692 WORK SAFELY! For maximum safety, perform

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS INSTALLATION INSTRUCTIONS Accessory REMOTE ENGINE STARTER SYSTEM Application 2010 CIVIC 4-DOOR Publications No. AII 42460 Issue Date AUG 2009 PARTS LIST Remote Engine Starter Unit Kit P/N 08E91-E22-100B

More information

Installation Instructions Unimatic Shifter

Installation Instructions Unimatic Shifter Installation Instructions Unimatic Shifter Universal Shifter for Automatic Transmissions Part Number 80775 2010, 2000 by B&M Racing & Performance Products The B&M Unimatic is a universal shifter that will

More information

Photo 1. Shift pattern gate plate

Photo 1. Shift pattern gate plate Installation Instructions MAGNUM GRIP STREET BANDIT SHIFTER Fits: GM, Chrysler, and Ford Automatic Transmissions See Application Guide for Specific Vehicles Catalog # 81050 WORK SAFELY! For maximum safety,

More information

PRELIMINARY INSTALLATION INSTRUCTIONS. Remote Engine Starter Attachment Kit P/N 08E92-SNA-100B

PRELIMINARY INSTALLATION INSTRUCTIONS. Remote Engine Starter Attachment Kit P/N 08E92-SNA-100B INSTALLATION INSTRUCTIONS Accessory Application Publications No. REMOTE ENGINE STARTER SYSTEM 2008 CIVIC 2-DOOR AII 38215 Issue Date OCT 2007 PARTS LIST Remote Engine Starter Unit Kit P/N 08E91-E22-100B

More information

w w w. h d o n l i n e s h o p. d e CRUISE CONTROL KIT GENERAL INSTALLATION -J04064 REV Kit Number Models Additional Parts Required

w w w. h d o n l i n e s h o p. d e CRUISE CONTROL KIT GENERAL INSTALLATION -J04064 REV Kit Number Models Additional Parts Required -J006 REV. 006-08- CRUISE CONTROL KIT GENERAL Kit Number 7796-07 Models For the most up-to-date model fitment information, please see the product label or www.harley-davidson.com. Additional Parts Required.

More information

1967 (Late) and 1968 CORVETTE TELESCOPING STEERING COLUMN DISASSEMBLY & REPAIR INSTRUCTIONS - PAPER #1

1967 (Late) and 1968 CORVETTE TELESCOPING STEERING COLUMN DISASSEMBLY & REPAIR INSTRUCTIONS - PAPER #1 Last Revision: 03SE2012 1967 (Late) and 1968 CORVETTE TELESCOPING STEERING COLUMN DISASSEMBLY & REPAIR INSTRUCTIONS - PAPER #1 Disassembly and Repair Instructions Addressed in this Paper Difficulty Page

More information

Retro it Steering Column

Retro it Steering Column Retro it Steering Column INSTALLATION INSTRUCTIONS for 1976-86 CJ5 & CJ7 FOR PART NUMBER S: 1520800010, 1520800020, 1520800051, 1526800010, 1526800020, 1526800051 S I NCE 1986 Instruction # 8000000010

More information

SERVICE PROCEDURES FOR CLUTCH HYDRAULIC UNITS

SERVICE PROCEDURES FOR CLUTCH HYDRAULIC UNITS SERVICE PROCEDURES FOR CLUTCH HYDRAULIC UNITS SAFETY PROCEDURES Always follow the vehicle manufacturer's recommended safety procedures in your Shop and Owners Manual. REQUIRED TOOLS Flat blade screwdriver,

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS INSTALLATION INSTRUCTIONS Accessory Application Publications No. BII 37248 2008 TSX Issue Date JUNE 2007 PARTS LIST 1. Make sure you have the anti-theft code for the radio, then write down the frequencies

More information

IMPORTANT: When replacing the ignition lock cylinder only, the passlock relearn procedure is not required.

IMPORTANT: When replacing the ignition lock cylinder only, the passlock relearn procedure is not required. A 1 of 11 2/18/2012 3:27 PM IMPORTANT: The important statement at the beginning of the "Ignition Lock Cylinder removal procedure on page 188 in the 2000/2001 Saturn S-Series Body/Electrical Volume II Service

More information

STEERING COLUMN SWITCHES

STEERING COLUMN SWITCHES STEERING COLUMN SWITCHES 1995 Volvo 850 1995-96 ACCESSORIES & EQUIPMENT Volvo Steering Column Switches 850 TESTING NOTE: Testing information on steering column switches is not available from manufacturer.

More information

Installation Instructions Unimatic Shifter

Installation Instructions Unimatic Shifter Installation Instructions Unimatic Shifter Universal Shifter for Automatic Transmissions Part Number 80775 2000 by B&M Racing & Performance Products LLC The B&M Unimatic is a universal shifter that will

More information

Technical Support (707)

Technical Support (707) Installation Instructions UNIMATIC SHIFTER Fits: GM, Powerglide, Ford and Chrysler Transmissions See Application Guide for Specific Vehicles Catalog # 80775 WORK SAFELY! For maximum safety, perform this

More information

MANUAL TRANSAXLE Return to Main Table of Contents

MANUAL TRANSAXLE Return to Main Table of Contents MANUAL TRANSAXLE Return to Main Table of Contents GENERAL... 2 MANUAL TRANSAXLE CONTROL... 12 SHIFT LEVER ASSEMBLY... 14 MANUAL TRANSAXLE... 15 MANUAL TRANSAXLE ASSEMBLY... 17 FIFTH SPEED SYNCHRONIZER

More information

GENUINE PARTS INSTALLATION INSTRUCTIONS

GENUINE PARTS INSTALLATION INSTRUCTIONS GENUINE PARTS INSTALLATION INSTRUCTIONS 1 DESCRIPTION: 2 APPLICATION: 3 PART NUMBER(S) REQUIRED FOR INSTALLATION: Fog Lamp Kit Rogue w/ AL 999F1 G2000 (Fog Lamp Kit) 4 KIT CONTENTS: Item Qty. Part Description

More information

DISASSEMBLY. Transmission. 2. Remove the 4 clutch housing bolts. Separate the clutch housing from the transmission.

DISASSEMBLY. Transmission. 2. Remove the 4 clutch housing bolts. Separate the clutch housing from the transmission. 308-03A-1 DISASSEMBLY Transmission 308-03A-1 Special Tool(s) Puller, Bearing 205-D064 (D84L-1123-A) or equivalent Remover/Installer, Front Wheel Hub 204-069 (T81P-1104-C) 2. Remove the 4 clutch housing

More information

CERTAIN MODEL YEAR FUSION AND ESCAPE VEHICLES EQUIPPED WITH A 6F35 TRANSMISSION SHIFTER CABLE BUSHING REPLACEMENT

CERTAIN MODEL YEAR FUSION AND ESCAPE VEHICLES EQUIPPED WITH A 6F35 TRANSMISSION SHIFTER CABLE BUSHING REPLACEMENT PAGE 1 OF 9 CERTAIN 2013-2016 MODEL YEAR FUSION AND 2013-2014 ESCAPE VEHICLES EQUIPPED WITH A 6F35 TRANSMISSION SHIFTER CABLE BUSHING REPLACEMENT OVERVIEW In some of the affected vehicles, the bushing

More information

Installation Instructions Pro Stick Shifter

Installation Instructions Pro Stick Shifter Installation Instructions Pro Stick Shifter Part Number 80701, 80702 & 80706 2012, 2010, 2008, 2001, 1998 by B&M Racing and Performance Products The B&M Pro Stick shifter #80701 and #80706 comes equipped

More information

DRIVE AXLE Volvo 960 DESCRIPTION & OPERATION AXLE IDENTIFICATION DRIVE AXLES Volvo Differentials & Axle Shafts

DRIVE AXLE Volvo 960 DESCRIPTION & OPERATION AXLE IDENTIFICATION DRIVE AXLES Volvo Differentials & Axle Shafts DRIVE AXLE 1994 Volvo 960 1994 DRIVE AXLES Volvo Differentials & Axle Shafts 960 DESCRIPTION & OPERATION All 960 station wagon models use type 1041 rear axle assembly. All 960 4-door models use type 1045

More information

STEERING Chrysler Motors/Mitsubishi - Steering Columns - FWD

STEERING Chrysler Motors/Mitsubishi - Steering Columns - FWD Article Text ARTICLE BEGINNING 1991-92 STEERING Chrysler Motors/Mitsubishi - Steering Columns - FWD Dodge; Colt, Colt 200, Colt Vista, Stealth Eagle; Summit & 1992 Summit Wagon Mitsubishi; Eclipse, Galant,

More information

1993 ACCESSORIES & EQUIPMENT Volkswagen Steering Column Switches. Cabriolet, Corrado SLC, EuroVan, Fox, Golf, GTI, Jetta, Passat

1993 ACCESSORIES & EQUIPMENT Volkswagen Steering Column Switches. Cabriolet, Corrado SLC, EuroVan, Fox, Golf, GTI, Jetta, Passat Article Text ARTICLE BEGINNING 1993 ACCESSORIES & EQUIPMENT Volkswagen Steering Column Switches Cabriolet, Corrado SLC, EuroVan, Fox, Golf, GTI, Jetta, Passat * PLEASE READ THIS FIRST * CAUTION: Cabriolet

More information

4. Front and Rear Drive Shafts

4. Front and Rear Drive Shafts 4-2 SERVICE PROCEDURE 3. Rear Axle (FWD) - Tightening torque: 186±20 N m (19±2 kg-m, 137±14 ft-lb) Use a new axle nut. Always tighten axle nut before installing wheel on vehicle. If wheel is installed

More information

54531/ FORD FUSION

54531/ FORD FUSION 54531/51531 54531/51531 13-15 FORD FUSION 13-15 FORD FUSION FORD FUSION Upper Class Grille w/ Bars TOOLS REQUIRED: Socket Set Flat/Phillips Screw Drivers Torx Bits Plastic Pry Bar 3/16 Drill Bit and Drill

More information

HYDRAULICS. TX420 & & lower. Hydraulic Tandem Pump Removal. 4. Remove the LH side panel (Fig. 0388).

HYDRAULICS. TX420 & & lower. Hydraulic Tandem Pump Removal. 4. Remove the LH side panel (Fig. 0388). TX420 & 425 240000299 & lower 4. Remove the LH side panel (Fig. 0388). Hydraulic Tandem Pump Removal Note: Cleanliness is a key factor in a successful repair of any hydraulic system. Thoroughly clean all

More information

1995 Jeep Grand Cherokee Limited. CRUISE CONTROL SYSTEM' '1995 ACCESSORIES & SAFETY EQUIPMENT Chrysler Corp. Cruise Control Systems

1995 Jeep Grand Cherokee Limited. CRUISE CONTROL SYSTEM' '1995 ACCESSORIES & SAFETY EQUIPMENT Chrysler Corp. Cruise Control Systems TROUBLE SHOOTING NO CRUISE CONTROL WHEN SET BUTTON IS PRESSED & RELEASED Check for: blown fuse, no vacuum at servo and/or defective servo, disconnected speed control cable, brakelight switch out of adjustment,

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS INSTALLATION INSTRUCTIONS Accessory REMOTE CONTROL Application 2014 TSX (L4) Publications No. BII 50198 Issue Date SEPT 2013 PARTS LIST Remote Engine Starter Unit Kit P/N 08E91-TK4-200A Fuse label Transmitter

More information

GM Floor Mount Automatic Transmission Shifter Installation Instructions

GM Floor Mount Automatic Transmission Shifter Installation Instructions GM Mount Automatic Transmission Shifter Installation Instructions Building American Quality With A Lifetime Warranty! TOLL FREE 1-877-469-7440 tech@lokar.com www.lokar.com GM Mount Automatic Transmission

More information

Ford AOD-4R70W-AODE Cable Operated Shifter Installation Instructions

Ford AOD-4R70W-AODE Cable Operated Shifter Installation Instructions Ford AOD-4R70W-AODE Cable Operated Shifter Installation Instructions Building American Quality With A Lifetime Warranty! TOLL FREE 1-877-469-7440 tech@lokar.com www.lokar.com Ford AOD-4R70W-AODE Cable

More information

LGT-306L / LB Club Car Precedent LED Light Bar Bumper Kit Installation Instructions

LGT-306L / LB Club Car Precedent LED Light Bar Bumper Kit Installation Instructions LGT-306L / LB Club Car Precedent LED Light Bar Bumper Kit Installation Instructions Caution: Please read through the instructions carefully. Before starting this project, remove the system s positive and

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS INSTALLATION INSTRUCTIONS Accessory Application 2013 MDX Publications No. BII 13440 Issue Date JULY 2012 PARTS LIST INSTALLATION Steering wheel 2 TORX bolts Client Information: The information in this

More information

Ford AOD-4R70W-AODE Cable Operated Shifter Installation Instructions

Ford AOD-4R70W-AODE Cable Operated Shifter Installation Instructions Ford AOD-4R70W-AODE Cable Operated Shifter Installation Instructions Building American Quality With A Lifetime Warranty! TOLL FREE 1-877-469-7440 tech@lokar.com www.lokar.com Ford AOD-4R70W-AODE Cable

More information

#TL T EA888 GEN 3 FUELING SYSTEM/ INSTALLATION INSTRUCTIONS

#TL T EA888 GEN 3 FUELING SYSTEM/ INSTALLATION INSTRUCTIONS #TL100069 2.0T EA888 GEN 3 FUELING SYSTEM/ INSTALLATION INSTRUCTIONS Notes: These instructions were written for a North American specification MkVII GTI. Other models, like the Golf R, are similar. When

More information

Installation Instructions Hammer Shifter Fits: GM, Ford, Chrysler Transmissions See Application Guide for Specific Applications Part # 80885

Installation Instructions Hammer Shifter Fits: GM, Ford, Chrysler Transmissions See Application Guide for Specific Applications Part # 80885 Installation Instructions Hammer Shifter Fits: GM, Ford, Chrysler Transmissions See Application Guide for Specific Applications Part # 80885 WORK SAFELY! For maximum safety, perform this installation on

More information

Installation Instructions Console Megashifter

Installation Instructions Console Megashifter Installation Instructions Console Megashifter 1968-1969 Camaro Part Number 81035 This B&M Megashifter is designed to fit in the console of a 1968-1969 Chevrolet Camaro. In 1968, these vehicles were equipped

More information

2003 Dodge Pickup R DRIVE AXLES' 'Axle Shafts - Front - Ram Pickup WD DRIVE AXLES

2003 Dodge Pickup R DRIVE AXLES' 'Axle Shafts - Front - Ram Pickup WD DRIVE AXLES 2002-04 DRIVE AXLES Axle Shafts - Front - Ram Pickup 1500 4WD DESCRIPTION Vehicles equipped with 4WD and C205F front axle assembly use equal length axle shaft system to deliver power from front differential

More information

OVERVIEW: KIT INCLUDES:

OVERVIEW: KIT INCLUDES: Please visit www.fordracingparts.com for the most current instruction information!!! PLEASE READ ALL OF THE FOLLOWING INSTRUCTIONS CAREFULLY PRIOR TO INSTALLATION. AT ANY TIME YOU DO NOT UNDERSTAND THE

More information

Transmission Overhaul Procedures-Bench Service

Transmission Overhaul Procedures-Bench Service How to Assemble the Lower Reverse Idler Gear Assembly Special Instructions In 1996 Eaton changed the reverse idler system design. In the nut design, the reverse idler bearing was lubricated through a hole

More information

Lotus Service Notes Section HG

Lotus Service Notes Section HG STEERING SECTION HG Sub-Section Page General Description HG.1 2 Steering Wheel HG.2 2 Upper Column Assembly HG.3 5 Intermediate Column HG.4 9 Front Wheel Alignment & Rack Gaiters HG.5 9 Rack & Pinion Assembly

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS INSTALLATION INSTRUCTIONS Accessory REMOTE CONTROL Application 2012 ODYSSEY (EXCEPT LX) Publications No. AII 46745 Issue Date SEP 2011 PARTS LIST Remote Control Engine Starter Unit Kit P/N 08E91-E22-101A

More information

Torqueflite Manual/Automatic Valve Body

Torqueflite Manual/Automatic Valve Body TCI 122400 Torqueflite Manual/Automatic Valve Body This valve body can be installed in a few hours by carefully following directions. Read all instructions first to familiarize yourself with the parts

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS INSTALLATION INSTRUCTIONS --1075 North Ave. Sanger, CA 93657-3539 local: 559-875-0222 fax: 559-876-2259 toll free: 800-445-3767-- 2505 Lowering Spindle Assembly Installation Instructions ½ TON SILVERADO

More information

STEERING 19-1 STEERING CONTENTS

STEERING 19-1 STEERING CONTENTS ZJ STEERING 19-1 STEERING CONTENTS page POWER STEERING GEAR... 9 POWER STEERING PUMP... 4 POWER STEERING... 1 page STEERING COLUMN... 20 STEERING LINKAGE... 24 POWER STEERING INDEX page GENERAL INFORMATION

More information

ALLDATA Online Chevy Truck Avalanche WD V8-5.3L VIN T - Steering... Page 1 of 12. Steering Wheel Module Coil Replacement (Coil)

ALLDATA Online Chevy Truck Avalanche WD V8-5.3L VIN T - Steering... Page 1 of 12. Steering Wheel Module Coil Replacement (Coil) ALLDATA Online - 2006 Chevy Truck Avalanche 1500 2WD V8-5.3L VIN T - Steering... Page 1 of 12 Steering Wheel Module Coil Replacement (Coil) INFLATABLE RESTRAINT STEERING WHEEL MODULE COIL REPLACEMENT (COIL)

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS INSTALLATION INSTRUCTIONS Accessory REMOTE CONTROL Application 2008 CR-V Publications No. AII 35843-38422 Issue Date DEC 2007 PARTS LIST Caution label Remote Engine Starter Kit P/N 08E91-E22-100B Transmitter

More information

Front seats. j a t CAUTION! Before beginning repairs on the electrical system: Obtain the anti-theft radio security code. Switch the ignition off.

Front seats. j a t CAUTION! Before beginning repairs on the electrical system: Obtain the anti-theft radio security code. Switch the ignition off. j a t Front seats 72-1 CAUTION! Before beginning repairs on the electrical system: Obtain the anti-theft radio security code. Switch the ignition off. Search Advanced Search Disconnect the battery Ground

More information

RANGER 900 POWER STEERING KIT

RANGER 900 POWER STEERING KIT RANGER 900 POWER STEERING KIT P/N 2880083 APPLICATION MY14 AND NEWER RANGER XP 900 MODELS IMPORTANT It is strongly recommended that this kit be installed by an authorized Polaris dealer. NOTE Use of this

More information

STEERING COLUMN SWITCHES

STEERING COLUMN SWITCHES STEERING COLUMN SWITCHES 1994 Toyota Celica 1994 ACCESSORIES & EQUIPMENT Toyota Motor Sales, U.S.A., Inc. - Steering Column Switches Celica * PLEASE READ THIS FIRST * WARNING: Are equipped with a driver-side

More information

1 of 7 7/22/2013 8:41 AM

1 of 7 7/22/2013 8:41 AM 1 of 7 7/22/2013 8:41 AM REMOVAL 1. Turn the steering wheel so that the vehicle's wheels are pointing straight ahead. 2. Turn the ignition switch to "LOCK". 3. Disconnect the battery "-" terminal cable,

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS INSTALLATION INSTRUCTIONS Accessory REMOTE CONTROL Application Publications No. 2012 ACCORD AII 46522 2-DOOR Issue Date (A/T ONLY) AUG 2011 PARTS LIST Remote Engine Starter Unit Kit P/N 08E91-E22-101A

More information

Last Revision: 07SE2009

Last Revision: 07SE2009 Last Revision: 07SE2009 1967 (Late) and 1968 CORVETTE STANDARD (NON-ADJUSTABLE) STEERING COLUMN DISASSEMBLY & REPAIR INSTRUCTIONS PAPER #1 Disassembly and Repair Instructions Addressed in this Paper Difficulty

More information

DRIVE SHAFT LOCATION INDEX

DRIVE SHAFT LOCATION INDEX DRIVE SHAFT LOCATION INDEX 2005 DRIVELINE/AXLE Drive Shaft - MX-5 Miata Fig. 1: Identifying Drive Shaft Location DRIVE SHAFT PRE-INSPECTION 1. Inspect the dust boot on the drive shaft for cracks, damage,

More information

SPEED CONTROL SYSTEM

SPEED CONTROL SYSTEM DN SPEED CONTROL SYSTEM 8H - 1 SPEED CONTROL SYSTEM TABLE OF CONTENTS page AND SPEED CONTROL SYSTEM...1 SPEED CONTROL SERVO....2 SPEED CONTROL SOLENOID CIRCUITS...2 SPEED CONTROL SWITCHES...2 BRAKE LAMP

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS INSTALLATION INSTRUCTIONS Accessory REMOTE CONTROL Application 2011 ODYSSEY (EXCEPT LX) Publications No. AII 43923 Issue Date SEP 2010 PARTS LIST Remote Control Engine Starter Unit Kit P/N 08E91-E22-101A

More information

Printed in the U.S.A.

Printed in the U.S.A. Installation Instructions Hammer Shifter Part No. 80885 & 80887 2010, 2006, 2005, 2004, 1999 by B&M Racing and Performance Products (Visit www.bmracing.com for additional products and product information)

More information

Steering Column - Steering Column Removal and Installation

Steering Column - Steering Column Removal and Installation Page 1 of 7 Steering Column - Steering Column Removal and Installation Removal WARNING: Take care if releasing the adjustment lever when the column has been removed from the vehicle. The spring is under

More information

2001 Chevrolet CORVETTE

2001 Chevrolet CORVETTE riveline Support Assembly Replacement (Automatic Transmission) 1 of 21 10/24/2012 8:58 PM 2001 Chevrolet CORVETTE Submodel: Engine Type: V8 Liters: 5.7 Fuel Delivery: FI Fuel: GAS Driveline Support Assembly

More information