Drilling Tools. Drilling Tools

Transcription

1 Twist drills Miniature drills Sheet metal drills Spiral countersinks (core drills) Step drills Centre drills Taper pin drills Core drills Solid carbide drills Solid carbide tapping Tools Carbide indexable inserts Insert drills Rock drills Hammer drills Impact core cutters Countersink and deburring tools Countersinks and deburrers WPL countersinks Counterbores Spot facing cutters Hand reamers Taper reamers Helical taper pin reamers Taper structural reamers Chucking reamers Automatic machine reamers Clamp-on reamers Jet reamers Thread-cutting taps Forming taps Solid carbide thread-milling cutters Thread repair assortment Solid carbide tapping tools Tap extractors Arc erosion machines Tap and die sets Round dies

2 Our suppliers for DRILLING TOOLS: ß E eromobil Y P T X V T ; U Info Advantages: Coatings for machining tools Coating material TiN TiCN TiAlN Alcrona Hardlube Alu-CC Rocktec 52 Rocktec 65 Ultra-N Microhardness (HV.5) Friction coefficient gg. Steel (dry) Max. application temperature ( C) Coating colour Materials Coatings Superalloys Titanium alloys Cast iron Stainless steels Hardened steels to 65 HRC Hardened steels to 52 HRC High-alloy steels Low-alloy steels Al wrought alloys AlSi alloys Non-ferrous metals Plastics TiN TiCN TiAIN Alcrona Hardlube Alu-CC Rocktec 52 Rocktec 65 Ultra-N 1.2 Fax-Bestellhotline: order a a = Die angegebenen = Sales are restricted Preise sind to the Stückpreise. packaging Abgabe units mentioned nur in den angegebenen Verpackungseinheiten. the catalogue. Bestellangabe Purchase orders immer must in be Stück. in units. ( ) = Klammerpreise teilweise aus Lagervorrat. DE/P

3 Pictograph Overview Insert direction No centre cut, front milling is only possible via the workpiece edge With centre cut, immersion and front milling (possible in 3 directions) of thread e.g. MF = Metric Fine thread e.g. -E TiAIN = High-performance rapid machining Steel with cobalt (E) alloy and Titanium Aluminium-Nitrite coating of shank 1835 B 1835 D = straight shank with driving face in compliance with 1835 B = Straight shank with locking thread in compliance with 1835 D 6535 HA = Straight shank smooth in compliance with 6535 HA (for solid carbide tools) 6535 HB = Straight shank with driving face in compliance with 6535 HB (for solid carbide tools) Spiral angle e.g. = Spiral angle of the tool approx. 39 right 39 e.g. 12 = Spiral angle of the tool approx. 12 left Point angle e.g. = Point angle of the blades Tolerance e.g. H7 = Tolerance of cutting blades in compliance with ISO-recommendation R designation e.g. N = For machining standard duty materials Material strength e.g. = For materials with a strength to max. 1 N/mm 2 e.g. = For materials with a strength greater than 9 N/mm 2 Most suitable for = Aluminium = Grey cast iron = Brass = Universal VA = Rust-resistant, acid-resistant heat resistant and austenitic steels (V2A, V4A) Info The HHW colour-code system With the HHW colour-code system you can identify the materials for which the tool is suitable at fi rst glance. In most catalogue areas the HHW colour code system additionally informs you of the application data for the respective tool. The HHW colour code system is logically structured based on the Key to Steel. Thus you can fi nd the appropriate tools before processing and save time and money. St<11N St<12N St<14N <45HRC <55HRC <6HRC <67HRC VA-steel<9N VA-steel>9N Ti alloys GG(G) plastics Solid carbide types H 42 Coating coated Designation W ±,1 R ±, mm mm a GTN-2 2,2,16 1 pcs. 113 GTN-3 3,1,2 1 pcs. 114 PMK H 42 coated

4 Info Overview - twist drills (I) Brand ß ß ß Standard/ Short Short offset Short Short profile-ground Short rolled Short Short MBS Short Short Short Short Article number Cutting material -E -E -E -E -E Diameter range mm,3-2 13,5-2,3-16,5-13, ,3-16, N N N N N N UNI N Ti N VA-steel Point angle Coating TiN TiN TiAlN Catalogue page Application recommendation W = Well suited X = Limited suitability Aluminium < 1% Si X X X X X W X X Aluminium > 1% Si X X X X X W X X Copper X X X X X W X X Brass Steel < 52N W W W W W W W W W Steel < 75N W W W W W W W W W Steel < 9N W W W W W W W W W Steel < 11N W W W W W Steel < 12N W W W W Steel < 14N W W W VA-steel < 9N W W W W VA-steel > 9N W W W GG W W W W W W W GGG W W W W W W W Titanium W Titanium alloy W Nickel W < 55HRC < 6HRC < 67HRC Plastics X X X X X W X Brand T T T T ß Standard/ Company standard 1897 Short Short Short Short Short Short Short Mini Extra short Extra short Article number Cutting material -Co8 -E -E -E -E-PM -E Diameter range mm ,5-14,5-15 1, ,16-1,45 2, N FS FS H W VA-steel UNI N N N Point angle Coating TiN TiN Catalogue page Application recommendation W = Well suited X = Limited suitability Aluminium < 1% Si X X W X X X X X Aluminium > 1% Si X X W X X X X X Copper X X W X X X X X Brass W Steel < 52N W W W W W W W Steel < 75N W W W W W W W Steel < 9N W W W W W W W Steel < 11N W W W W W Steel < 12N W W W W W Steel < 14N W W W W VA-steel < 9N W W W W W VA-steel > 9N W W W W W GG W W W W GGG W W W W Titanium X X Titanium alloy X Nickel X < 55HRC < 6HRC < 67HRC Plastics X X X X X X X 1.4

5 Info Overview - twist drills (II) Brand ß T Standard/ Extra short Extra short Extra short MBS Extra short Extra short Long Long Long Long Long Article number Cutting material -E -E -E -E -E-PM -E Diameter range mm , VA-steel N UNI UNI UNI VA-steel N FS FW FN Point angle /13 / Coating TiN TiAIN TiN TiN Catalogue page Application recommendation W = Well suited X = Limited suitability Aluminium < 1% Si X X X X W W X Aluminium > 1% Si X X X X W W X Copper X X X X W X W X Brass Steel < 52N W W W W W W W W W Steel < 75N W W W W W W W W Steel < 9N W W W W W W W W Steel < 11N W W W W W W W W Steel < 12N W W W W Steel < 14N W W VA-steel < 9N W W W W W VA-steel > 9N W W W W W GG W W W W W W W W GGG W W W W W W W W Titanium W X Titanium alloy X Nickel X < 55HRC < 6HRC < 67HRC Plastics X X W Brand T T T T T Standard/ Overlong Overlong MT shank short MT shank short MT shank short MT shank short MT shank short MK-shank long Overlong Z3 Article number Cutting material -E -E Diameter range mm ,8-3 FN FN N N N N VA-steel N FN N Point angle Coating TiN TiN Catalogue page Application recommendation W = Well suited X = Limited suitability Aluminium < 1% Si X X X X X X Aluminium > 1% Si X X X X X Copper X X X X X Brass Steel < 52N W W W W W W W W W W Steel < 75N W W W W W W W W W W Steel < 9N W W W W W W W W W W Steel < 11N W W W W W Steel < 12N W W Steel < 14N W VA-steel < 9N W W W VA-steel > 9N W GG W W W W W W W W W GGG W W W W W W W W W Titanium X Titanium alloy X Nickel X < 55HRC < 6HRC < 67HRC Plastics X X 1.5

6 Info The CERATIZIT MasterGuide Material level The MasterGuide from CERATIZIT divides the materials in accordance with VDI 3323 in six main groups (P, M, K, N, S, H). A colour code is assigned to each group, in some cases these codes are familiar from ISO 513. Blue: Steel Machining steel, case-hardened steel, tempering steel, and structural steel Yellow: Stainless steel Ferritic Cr steels, Austenitic CrNi steels, martensitic Cr steels, duplex steels Red: Cast iron Grey cast iron, malleable cast iron, spheroidal cast iron, vermicular cast iron, sintered iron Green: Non-ferrous metals and non-metals AI wrought alloys, casting alloys, copper, copper alloys, non-metallic materials Orange: High-temperature alloys/titanium Ni-/Co based alloys, Ti alloys White: Hard materials Hardened steels ( 45 HRC), white cast iron, hard cast-iron materials Machining level Every colour code field is divided by lines into three levels. These indicate the respective types of machining: R = Rough machining M = Medium machining F = Fine machining Application level The ideal application area of a reversible cutting insert is marked by a a solid square. Extended application areas are marked by an empty square symbol Thus MasterGuide from CERATIZIT provides an overview for purchase, selection, and machining and reduces stock levels of types and geometries in the warehouse. Main application Extended application The right reversible cutting insert at a glance Main application: Medium, fine and rough machining of steel. Extended application: Medium machining of high-temperature resistant alloys. Medium, fine and rough machining of stainless steels. 1.6

7

8 Twist drills 11 Short twist drills Straight shank, right-hand cut, relieved cone grind. Starting at 1 mm, with web-thinned chisel edge. ground d 1 h8 l2 l 1 11, pcs. 69, pcs. 613, pcs. 618, pcs. 622, pcs. 626, pcs. 63, pcs. 635, pcs. 64, pcs. 644, pcs. 649, pcs. 654, pcs. 659, pcs. 663, pcs , pcs , pcs , pcs , pcs , pcs , pcs. 74 1, pcs , pcs , pcs , pcs , pcs. 73 1, pcs , pcs , pcs. 74 2, pcs , pcs , pcs , pcs. 75 2, pcs , pcs , pcs , pcs , pcs , pcs , pcs , pcs , pcs , pcs , pcs , pcs. 78 3, pcs , pcs , pcs , pcs , pcs , pcs , pcs , pcs , pcs , pcs. 8 4, pcs. 82 ground for steels to 9 N/mm 2. drill for highest demands. ground d 1 h8 l2 l , pcs. 84 4, pcs. 86 4, pcs. 89 4, pcs , pcs , pcs , pcs. 82 5, pcs , pcs , pcs , pcs , pcs , pcs , pcs , pcs , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , N ground d 1 h8 l2 l , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , Al<1%Si Al>1%Si Cu St<52N St<75N St<9N St<11N St<12N St<14N <45HRC <55HRC <6HRC <67HRC VA-steel<9N VA-steel>9N Ti-alloys GG(G) plastics

9 12 - Offset straight shank 12,7 mm ground for steels to 9 N/mm 2. Short twist drills Norm drill for highest demands. 12 N 118 ground d 1 h8 l 2 l , , , , , , ground d 1 h8 l 2 l , , , , , , Al<1%Si Al>1%Si Cu St<52N St<75N St<9N St<11N St<12N St<14N <45HRC <55HRC <6HRC <67HRC VA-steel<9N VA-steel>9N Ti-alloys GG(G) plastics ß - Straight shank ground for steels to 9 N/mm 2. Economically-priced ground version. 14 ß - Normal core strength without core rise - Precise centre point geometry - High true-running accuracy - Drill for production Short twist drills TiN profile-ground for steels to 9 N/mm Straight shank - Precision-rolled steel precision-rolled for steels to 9 N/mm 2. Note No microstructure interruption, thus elastic and suitable for robust drilling tasks (e.g. hand drill). 338 N ß ß d 1 h8 l 2 l , pcs , pcs , pcs , pcs , pcs , pcs , pcs , pcs , pcs , pcs , pcs , pcs , pcs , pcs , pcs , pcs , pcs , pcs , pcs , pcs , pcs ß ß d 1 h8 l 2 l , pcs , pcs , pcs , pcs , pcs , pcs , pcs , pcs , pcs , pcs , pcs , pcs , pcs , pcs , pcs , pcs , pcs , pcs , pcs , pcs , pcs Continuation. 1.9

10 Twist drills Short twist drills Continuation. ß ß d 1 h8 l 2 l , pcs , pcs , pcs , pcs , pcs , pcs , pcs , pcs , pcs , pcs , pcs , pcs , pcs , pcs , pcs , pcs , pcs , pcs , pcs , pcs , pcs , pcs , pcs , pcs , pcs , pcs , pcs , pcs , pcs , pcs , pcs , pcs , pcs , pcs , pcs , pcs , pcs , pcs N 118 ß ß d 1 h8 l 2 l , pcs , pcs , pcs , pcs , pcs , pcs , pcs , pcs , pcs , pcs , pcs , pcs , pcs , pcs , pcs , pcs , pcs , pcs , pcs , pcs , pcs , , , , , , , , , , , , , , , , , Al<1%Si Al>1%Si Cu St<52N St<75N St<9N St<11N St<12N St<14N <45HRC <55HRC <6HRC <67HRC VA-steel<9N VA-steel>9N Ti-alloys GG(G) plastics Short twist drills 12 - Straight shank - Web-thinned chisel edge - High true-running accuracy - Long service life /TiN ground for steels to 12 N/mm 2, cast iron, graphite, brass, etc. Drill for production. 135 Multi-purpose twist drills MBS 12 - Straight shank - Special web-thinning - 4-surface grind -E ground. Multi-purpose use, quiet drilling, low torque, high dimensional accuracy, optimal chip removal thanks to the round flute profile. N TiN -E Continuation. 1.1

11 Short twist drills Continuation. /TiN MBS 12 d 1 h8 l 2 l , pcs , pcs , pcs , pcs , pcs , pcs , pcs , pcs , pcs , pcs , pcs , pcs , pcs , pcs , pcs , pcs , pcs , pcs , pcs , pcs , pcs , pcs , pcs , pcs , pcs , pcs , pcs , pcs , pcs , pcs , pcs , pcs , pcs , pcs , pcs , pcs , pcs , pcs , pcs , pcs , pcs , pcs , pcs , pcs , pcs , pcs , pcs , pcs , pcs , pcs , pcs , /TiN MBS 12 d 1 h8 l 2 l , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , Al<1%Si Al>1%Si Cu St<52N St<75N St<9N St<11N St<12N St<14N <45HRC <55HRC <6HRC <67HRC VA-steel<9N VA-steel>9N Ti-alloys GG(G) plastics

12 Twist drills 14 ß - Straight shank - From diameter 1. mm web-thinned chisel edge - High true-running accuracy - Precise centre point geometry Short twist drills -E ground for high-alloyed steels with a strength of up to 12 N/mm 2. drill which satisfies the highest requirements. Drill for production. 338 N 118 -E 14 -E d 1 h8 l 2 l 1 14, pcs. 69, pcs. 618, pcs. 626, pcs. 635, pcs. 644, pcs. 654, pcs , pcs , pcs , pcs , pcs , pcs , pcs. 74 1, pcs , pcs , pcs , pcs. 73 2, pcs , pcs , pcs , pcs , pcs. 75 2, pcs , pcs , pcs , pcs , pcs , pcs , pcs , pcs , pcs , pcs , pcs. 78 3, pcs , pcs , pcs , pcs , pcs , pcs , pcs E d 1 h8 l 2 l , pcs , pcs. 8 4, pcs. 82 4, pcs. 84 4, pcs. 86 4, pcs. 89 4, pcs , pcs , pcs , pcs. 82 5, pcs , pcs , pcs , pcs , pcs , pcs , pcs , pcs , pcs , pcs , pcs , pcs , pcs , pcs , pcs , pcs , pcs. 85 7, pcs , pcs , pcs , pcs , pcs , pcs , pcs. 86 7, pcs , pcs , pcs , pcs , pcs , pcs. 87 -E d 1 h8 l 2 l , pcs , pcs , pcs , pcs , pcs , pcs , pcs , pcs , pcs , pcs , pcs , pcs. 89 9, pcs , pcs , pcs , pcs , pcs , pcs , pcs , pcs , pcs. 94 1, , , , , , , , , , , , , , , , , Al<1%Si Al>1%Si Cu St<52N St<75N St<9N St<11N St<12N St<14N <45HRC <55HRC <6HRC <67HRC VA-steel<9N VA-steel>9N Ti-alloys GG(G) plastics Performance requires quality. For example, with the solid carbide high-performance ALUSPEED drill, from ATORN. 6x guiding section Solid carbide Ultra finest grit Al-CC-coating to 8xD Twisted cooling channel Performance requires quality. 1.12

13 Short twist drills - Straight shank - Starting at 1 mm, with web-thinned chisel edge. - High true-running accuracy - Precise centre point geometry drill for highest demands. Drill for production E for materials that are difficult to machine, such as titanium and special materials, such as Nimonic, Hastelloy and Inconel. Ti N VA d 1 h8 l 2 l , pcs. 15, pcs. 16 1, pcs , pcs , pcs , pcs , pcs , pcs , pcs , pcs , pcs , pcs , pcs , pcs , pcs , pcs , pcs , pcs , pcs , pcs , pcs , pcs , pcs , pcs , pcs , pcs , pcs , pcs , pcs , pcs , pcs , pcs , pcs , pcs , pcs , pcs , pcs , pcs , pcs , pcs , pcs , pcs , pcs , pcs , pcs , pcs , pcs E/TiAlN-coated for high-alloyed steels with a strength of up to 12 N/mm 2. Maximum service lives are possible E for rust-resistant, acid resistant and heat resistant steels, such as V2A and V4A. Ti N VA -E -E TiAIN -E 338 VA Ti N VA d 1 h8 l 2 l , pcs , pcs , pcs , pcs , pcs , pcs , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , Continuation. 1.13

14 Twist drills Continuation. Ti N VA d 1 h8 l 2 l , , , , , , , Ti N VA d 1 h8 l 2 l , , , , , , , Al<1%Si Al>1%Si Cu St<52N St<75N St<9N St<11N St<12N St<14N <45HRC <55HRC <6HRC <67HRC VA-steel<9N VA-steel>9N Ti-alloys GG(G) plastics Straight shank - Web-thinned chisel edge - High true-running accuracy - Precise centre point geometry - Drilling without centring. Co8 twist drill -Co8 ground for high-strength CrNi-based alloys. VA-steel, wear-resistant sheet metal and steel with a strength of up to 14 N/mm 2. drill for utmost demands. Drill for production. 338 N 135 Co Co8 d 1 h8 l 2 l , pcs. 11 1, pcs , pcs , pcs , pcs , pcs , pcs , pcs , pcs , pcs , pcs. 12 2, pcs , pcs , pcs , pcs , pcs , pcs , pcs , pcs , pcs. 13 3, pcs , pcs , pcs , pcs , pcs , pcs , pcs , pcs , pcs , pcs. 14 4, pcs , pcs , pcs Co8 d 1 h8 l 2 l , pcs , pcs , pcs , pcs , pcs , pcs , pcs. 15 5, pcs , pcs , pcs , pcs , pcs , pcs , pcs , pcs , pcs , pcs. 16 6, , , , , , , , , , , , , , , , Co8 d 1 h8 l 2 l , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , Al<1%Si Al>1%Si Cu St<52N St<75N St<9N St<11N St<12N St<14N <45HRC <55HRC <6HRC <67HRC VA-steel<9N VA-steel>9N Ti-alloys GG(G) plastics

15 Short twist drills - Straight shank - Web-thinned chisel edge - High true-running accuracy - Precise centre point geometry - Starting at 2 mm nitrided lands - Wide flutes and rounded heels for optimal chip transport 15 -E for steels to 12 N/mm E/TiN coated for even higher machining performance -E -E TiN 338 FS drill for utmost demands. Drill for production. -E -E/TiN d 1 h8 l 2 l , pcs , pcs. 17 1, pcs , pcs , pcs , pcs , pcs , pcs , pcs , pcs , pcs , pcs , pcs , pcs. 15 2, pcs , pcs , pcs , pcs , pcs , pcs , pcs , pcs , pcs , pcs , pcs , pcs , pcs , pcs , pcs , pcs , pcs , pcs , pcs , pcs , pcs , pcs , pcs , pcs E -E/TiN d 1 h8 l 2 l , pcs , pcs , pcs , pcs. 24 5, pcs , pcs , pcs , pcs , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , Al<1%Si Al>1%Si Cu St<52N St<75N St<9N St<11N St<12N St<14N <45HRC <55HRC <6HRC <67HRC VA-steel<9N VA-steel>9N Ti-alloys GG(G) plastics

16 Twist drills Stable metal folding box with drill organisation system Final digits 115 (1-1,5 mm) incl. twist drills 3,3 / 4,2 / 6,8 / 1,2 mm Ø for threaded holes (ISO). Twist drill sets in case 117 N, ground (cat.-no. 11) ß N, ground (cat.-no. 13). 134 UNI -E. (cat.-no. 135) ß N -E, ground (cat.-no. 14). 338 N TiN -E N /TiN, ground (cat.-no. 12) N, precisely rolled steel (cat.-no. 11). /TiN -E/UNI -E rolled steel Set size Number of Increments mm drills by mm 1, - 6, 51, , - 1, 81, , - 1, 41, , - 1, 19, , - 1,5 24, , - 13, 25, Sheet steel case with 18 twist drills. Contents: each 1 pcs.,5-8 mm, each 5 pcs. 8,5-1 mm,,5 mm increments. Twist drill sets in case 118, ground (cat.-no. 11) ß, ground (cat.-no. 13). 1182, precision-rolled steel. (cat.-no. 11) Empty case. For max. 6 twist drills (,5-1 mm Ø,,5 mm/increments). Dimensions: 325 x 225 x 5 mm. 338 N rolled steel empty Sets packed in oil paper. For re-filling and supplementing existing assortment cases. Final digits 115 (1-1,5 mm) incl. twist drills 3,3 / 4,2 / 6,8 / 1,2 mm Ø for threaded holes (ISO) Twist drill sets 1185, ground (cat.-no. 11) ß, ground (cat.-no. 13) ß -E, ground (cat.-no. 14). 1188, precision-rolled steel. (cat.-no. 11). 338 N -E E rolled steel Set size No. of Increments mm drills by mm 1, - 6, 51, , - 1, 81, , - 1, 41, , - 1, 19, , - 1,5 24, , - 13, 25,

17 119 Twist Drill Cases (Empty) Without drills. When the lid is opened, the drills are automatically tilted up to vertical position. For clearly arranged storage of short twist drills with straight shank 338, in sets (cat.-no ) and all other short twist drills with straight shank with the respective diameters and lengths. Cat.-no with additional slots for thread core drills (ISO and BSW): cat.-no = 3,3 / 4,2 / 6,8 and 1,2 mm, cat.-no = 1,9 / 2,1 / 2,6 / 2,9 / 3,2 / 3,3 / 3,8 / 4,2 / 5,1 / 6,8 / 7,9 / 1,2 mm. 119 For spiral drill Number of Increments 119 sets Ø mm drills of mm 1, - 6, 51,1 16 2, - 1, 81,1 18 6, - 1, 41,1 19 1, - 1, 19,5 114 For spiral drill Number of Increments 119 sets Ø mm drills of mm 1, - 1,5 24, , - 1,5 32, , - 13, 25, Plastic Stands for Twist Drills (Empty) Without drills. For clearly organised storage of twist drills with straight shank in different sets For set size Increments 1195 mm of mm 1, - 5,,1 11 5,1-1,,1 13 1, - 5,9,1 17 1, - 1,, , - 13,, T Straight shank ground. Short twist drills Special drill with wide, spacious flutes for hard and brittle materials (brass, bronze) Aluminium twist drill - Straight shank ground VA-steel twist drill - Straight shank - High true-running accuracy - Precise centre point geometry - Drilling without centring. -E ground. For rust-resistant, acid resistant and heat resistant steels, such as V2A und V4A. Drills for production. H W IS E 338 VA Special drill with polished flutes for optimal chip transport in soft materials. Drill for production. Continuation. 1.17

18 Twist drills Short-chip drill Short twist drills Continuation. -E d 1 h8 l 2 l , pcs , pcs , pcs , pcs , pcs , pcs , pcs , pcs , pcs , pcs , pcs , pcs , pcs , pcs , pcs , pcs , pcs , pcs , pcs , pcs , pcs , pcs , pcs , pcs , pcs , pcs , pcs , pcs , pcs , pcs , pcs , pcs , pcs , pcs , pcs , pcs , pcs , pcs , pcs , pcs , pcs , pcs , pcs , pcs , pcs , pcs , pcs , pcs , pcs , pcs , pcs , pcs , pcs , pcs E d 1 h8 l 2 l , pcs , pcs , pcs , pcs , pcs , pcs , pcs , pcs , pcs , pcs , pcs , pcs , pcs , pcs , pcs , pcs , pcs , pcs , pcs. 67 7, pcs , pcs , pcs , pcs , pcs , pcs , pcs , pcs , pcs , pcs , pcs , pcs , pcs , pcs , pcs , pcs , pcs , pcs , pcs , pcs , pcs , pcs , pcs , pcs , pcs , pcs , , , , , , , , Al<1%Si Al>1%Si Cu Ms Mg St<52N St<75N St<9N St<11N St<12N St<14N <45HRC <55HRC <6HRC <67HRC Ti-alloys GG(G) plastics

19 Special profile - Low wear on the cutting edges - Temperature-resistant -E-PM/TiN for universal use. High true-running accuracy, long service life and good dimensional accuracy. Short chips. Drilling without centring. Drill for production. High-performance short-chip drill UNI E-PM TiN E-PM/TiN d 1 h8 l 2 l , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , E-PM/TiN d 1 h8 l 2 l , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , E-PM/TiN d 1 h8 l 2 l , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , Al<1%Si Al>1%Si Cu St<52N St<75N St<9N St<11 St<12 St<14 <45HRC <55HRC <6HRC <67HRC VA-steel<9NVA-steel>9NTi-alloys GG(G) plastics Info The HHW colour-code system With the HHW colour-code system you can identify the materials for which the tool is suitable at fi rst glance. In most catalogue areas the HHW colour code system additionally informs you of the application data for the respective tool. The HHW colour code system is logically structured based on the Key to Steel. Thus you can fi nd the appropriate tools before processing and save time and money. St<11N St<12N St<14N <45HRC <55HRC <6HRC <67HRC VA-steel<9N VA-steel>9N Ti alloys GG(G) plastics Solid carbide types H 42 Coating coated Designation W ±,1 R ±, mm mm a GTN-2 2,2,16 1 pcs. 113 GTN-3 3,1,2 1 pcs. 114 PMK H 42 coated

20 Miniature drills Sheet metal drills Twist drills 122 T - Special drill with reinforced shank - High true-running accuracy - Precise point angle - To drill Ø,79 = shank Ø 1 mm - From drill Ø,8 = shank Ø 1,5 mm Miniature drills -E ground for multi-purpose use and for steel with a strength of up to 12 N/mm N 118 -E 122 -E d 1 l 2 l 1 122,16 1, pcs. 12,17 1, pcs. 13,18 1, pcs. 14,19 1, pcs. 15,2 1, pcs. 16,21 1, pcs. 17,22 1, pcs. 18,23 1, pcs. 19,24 1, pcs. 11,25 1, pcs. 111,26 1, pcs. 112,27 1, pcs. 113,28 1, pcs. 114,29 1, pcs. 115,3 1, pcs. 116,32 2, pcs. 118,33 2, pcs. 119,34 2, pcs. 12,35 2, pcs. 121,36 2, pcs. 122,38 2, pcs. 124,39 3, 25 1 pcs. 125,4 3, 25 1 pcs E d 1 l 2 l 1 122,42 3, 25 1 pcs. 128,43 3, 25 1 pcs. 129,44 3, 25 1 pcs. 13,45 3, 25 1 pcs. 131,47 3, 25 1 pcs. 133,48 3, 25 1 pcs. 134,49 3, pcs. 135,5 3, pcs. 136,52 3, pcs. 138,55 3, pcs. 141,56 3, pcs. 142,57 3, pcs. 143,58 3, pcs. 144,59 3, pcs. 145,6 3, pcs. 146,62 4, pcs. 148,63 4, pcs. 149,64 4, pcs. 15,65 4, pcs. 151,66 4, pcs. 152,7 4, pcs. 156,71 4, pcs. 157,72 4, pcs E d 1 l 2 l 1 122,73 4, pcs. 159,75 4, pcs. 161,79 5, pcs. 165,8 5, pcs. 166,81 5, pcs. 167,82 5, pcs. 168,83 5, pcs. 169,85 5, pcs. 171,9 6, 25 1 pcs. 176,92 6, 25 1 pcs. 178,95 6, 25 1 pcs. 181,96 6, pcs , 6, pcs ,5 6, pcs ,1 7, pcs ,15 7, pcs ,2 8, pcs. 19 1,25 8, pcs ,3 8, pcs ,4 9, pcs ,45 9, pcs. 195 Al<1%Si Al>1%Si Cu St<52N St<75N St<9N St<11N St<12N St<14N <45HRC <55HRC <6HRC <67HRC VA-steel<9N VA-steel>9N Ti-alloys GG(G) plastics ß - Double-sided ground - Extremely break-proof thanks to shortened flutes - Particularly suited for hand-guided machines - Surface specially treated Double-sided sheet metal drills ground. Especially for drilling thin sheet metal elements. N d 1 h8 l 2 l ,5 9, pcs. 14 3, 1, pcs. 15 3,1 11, pcs. 16 3,2 11, pcs. 17 d 1 h8 l 2 l ,3 11, pcs. 18 3,8 14, 55 1 pcs , 14, 55 1 pcs ,1 14, 55 1 pcs. 114 d 1 h8 l 2 l ,2 14, 55 1 pcs , 17, 62 1 pcs. 117 Info Precision short drill chucks Starting on page

21 Version - Straight shank High true-running accuracy. Long service life. Drill for production ground for steels to 9 N/mm 2. Extra short twist drills E with reinforced core and web-thinned for VA steels E/TiN with special web-thinning for quiet drilling and maximum service life in VA-steel, spring steel, special alloys such as Hastelloy, Nimonic and Inconel. N N VA E -E TiN 1897 VA E -E/TiN d 1 h8 l 2 l , pcs , pcs , pcs , pcs , pcs , pcs , pcs , pcs , pcs , pcs , pcs , pcs , pcs , pcs , pcs , pcs , pcs , pcs , pcs , pcs , pcs , pcs , pcs , pcs , pcs , pcs , pcs , pcs , pcs , pcs , pcs , pcs , pcs , pcs , pcs , pcs , pcs , pcs , pcs , pcs , pcs , pcs , pcs , pcs , pcs , pcs , pcs E -E/TiN d 1 h8 l 2 l , pcs. 8 5, pcs. 83 5, pcs , pcs , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , Continuation. 1.21

22 Twist drills Extra short twist drills Continuation. -E -E/TiN d 1 h8 l 2 l , , , , E -E/TiN d 1 h8 l 2 l , , , Al<1%Si Al>1%Si Cu St<52N St<75N St<9N St<11N St<12N St<14N <45HRC <55HRC <6HRC <67HRC VA-steel<9N VA-steel>9N Ti-alloys GG(G) plastics Version - Straight shank - Special web-thinning - 4-surface grind -E ground for multi-purpose use in VA-steel, steel with a strength of up to 12 N/mm 2, cast iron and aluminium. Multi-purpose twist drills MBS 12 Multi-purpose use, quiet drilling, low torque, high dimensional accuracy, perfect chip removal thanks to the round flute profile E E d 1 h8 l 2 l , pcs. 31 1, pcs. 32 1, pcs. 33 1, pcs. 34 1, pcs. 35 1, pcs. 36 1, pcs. 37 1, pcs. 38 1, pcs. 39 1, pcs. 31 2, pcs , pcs , pcs , pcs , pcs , pcs , pcs , pcs , pcs , pcs. 32 3, pcs , pcs , pcs , pcs , pcs , pcs , pcs , pcs , pcs , pcs. 33 4, pcs E d 1 h8 l 2 l , pcs , pcs , pcs , pcs , pcs , pcs , pcs , pcs , pcs. 34 5, pcs , pcs , pcs , pcs , pcs , pcs , pcs , pcs , pcs , pcs. 35 6, pcs , , , , , , , , , , , E d 1 h8 l 2 l , , , , , , , , , , , , , , , , , , , , , , , , , , , , , Al<1%Si Al>1%Si Cu St<52N St<75N St<9N St<11N St<12N St<14N <45HRC <55HRC <6HRC <67HRC VA-steel<9N VA-steel>9N Ti-alloys GG(G) plastics

23 126 UNI twist drill - NC shank - Structural dimensions similar to Special profile -E-Co/TiAlN. High true-running accuracy, long service life and good dimensional accuracy. Problem solver for all VA materials. Drill for production. Drilling without centring Point angle Point angle Point angle E TiAIN 126 d 2 -E/TiAlN d 1 h8 l 2 l 1 d 2 h7 126 mm 1, , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , E/TiAlN d 1 h8 l 2 l 1 d 2 h7 126 mm 5, , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , E/TiAlN d 1 h8 l 2 l 1 d 2 h7 126 mm 9, , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , Al<1%Si Al>1%Si Cu St<52N St<75N St<9N St<11N St<12N St<14N <45HRC <55HRC <6HRC <67HRC VA-steel<9N VA-steel>9N Ti-alloys GG(G) plastics

24 Short-chip drill Twist drills Special profile - Low wear on the cutting edges - Temperature-resistant -E-PM/TiN for universal use. High-performance short-chip drill UNI High true-running accuracy, long service life and good dimensional accuracy. Short chips. Drilling without centring. Drill for production E-PM TiN E-PM/TiN d 1 h8 l 2 l , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , E-PM/TiN d 1 h8 l 2 l , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , E-PM/TiN d 1 h8 l 2 l , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , Al<1%Si Al>1%Si Cu St<52N St<75N St<9N St<11N St<12N St<14 <45HRC <55HRC <6HRC <67HRC VA-steel<9NVA-steel>9NTi-alloys GG(G) plastics Straight shank - Web-thinned chisel edge Long twist drills 146 ground for machining standard duty materials to 9 N/mm E for materials that are difficult to machine, such as VA-steel, titanium and special materials. N VA E 34 VA Continuation. 1.24

25 Continuation. Long twist drills -E d 1 h8 l 2 l , pcs. 66, pcs. 68 1, pcs , pcs , pcs , pcs , pcs , pcs , pcs , pcs , pcs , pcs , pcs , pcs , pcs , pcs , pcs , pcs , pcs , pcs , pcs , pcs , pcs , pcs , pcs , pcs , pcs , pcs , pcs , pcs , pcs , pcs , pcs , pcs , pcs , pcs , pcs , pcs , pcs , pcs , pcs , pcs , pcs , pcs , pcs , pcs , pcs , pcs , pcs , pcs , pcs , pcs , pcs , E d 1 h8 l 2 l , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , Al<1%Si Al>1%Si Cu St<52N St<75N St<9N St<11N St<12N St<14N <45HRC <55HRC <6HRC <67HRC VA-steel<9N VA-steel>9N Ti-alloys GG(G) plastics

26 Deep hole drills Twist drills Straight shank - Web-thinned chisel edge - Reinforced core - Wide flutes - Highly rounded heels Deep hole drill For drilling deep holes (5-1 x d) without chip removal 147 ß ground for machining standard duty materials to 9 N/mm T Special drill with polished flutes for perfect chip transport in soft materials. FS FW FS FW d 1 h8 l 2 l , pcs. 21 1, pcs. 27 1, pcs , pcs , pcs , pcs , pcs , pcs , pcs , pcs , pcs , pcs , pcs , pcs , pcs , pcs , pcs , pcs , pcs , pcs , pcs , pcs , pcs , pcs , pcs , pcs , pcs , pcs. 29 3, pcs , pcs , pcs FS FW d 1 h8 l 2 l , pcs , pcs , pcs , pcs , pcs , pcs. 33 5, pcs , pcs , pcs , pcs , pcs , pcs , pcs , pcs , pcs , pcs , pcs. 17 8, pcs , pcs , pcs , pcs. 43 9, pcs , pcs , pcs , pcs , , , , , Al<1%Si Al>1%Si Cu St<52N St<75N St<9N St<11N St<12N St<14N <45HRC <55HRC <6HRC <67HRC VA-steel<9N VA-steel>9N Ti-alloys GG(G) plastics Straight shank - Web-thinned chisel edge - Reinforced core - Wide flutes - Highly rounded heels Long twist drills /TiN-coated for long service life in steel with a strength of up to 1 N/mm 2 and cast iron. For drilling deep holes under difficult conditions, e.g. poor chip removal, insufficient cooling. Warning: Exception: VA-steels, CrN-steels and similar materials. 34 FN 13 TiN 141 Continuation. 1.26

27 141 Long twist drills Continuation. /TiN d 1 h8 l 2 l , pcs. 11 1, pcs , pcs , pcs , pcs , pcs , pcs , pcs , pcs , pcs , pcs. 12 2, pcs , pcs , pcs , pcs , pcs , pcs , pcs , pcs , pcs , pcs. 13 3, pcs , pcs , pcs. 133 /TiN d 1 h8 l 2 l , pcs , pcs , pcs , pcs , pcs , pcs , pcs. 14 4, pcs , pcs , pcs , pcs , pcs , pcs , pcs , pcs , pcs. 15 5, pcs , pcs , pcs , pcs , pcs , pcs , pcs , pcs FN 13 TiN /TiN d 1 h8 l 2 l , pcs , pcs. 16 6, , , , , , , , , , , , , , , , , , , , Al<1%Si Al>1%Si Cu St<52N St<75N St<9N St<1N St<12N St<14N <45HRC <55HRC <6HRC <67HRC VA-steel<9N VA-steel>9N Ti-alloy GG(G) plastics Extra long twist drill 1869 FN Reihe 1, 2, 3 13 T Straight shank, right-hand cut, relieved cone grind. Web-thinned chisel edge Flat, wide flutes for holes with a diameter of up to 1 x D without chip removal, rounded heel, over 2.5 mm nitrided lands. ground for steel to 1 N/mm 2, cast iron, aluminium alloys, brass and bronze Reinforced core and highly rounded heels for drilling under difficult conditions, e.g. poor chip removal, insufficient cooling. /TiN-coated for long service life in steel to 1 N/mm 2 and cast iron. Warning: Exception: VA-steels, CrN-steels and similar materials. TiN /TiN d 1 h8 x l 1 l mm mm 2, x ,5 x , x , x ,5 x ,5 x , x , x , x ,5 x ,5 x , x , x , x /TiN d 1 h8 x l 1 l mm mm 5,5 x ,5 x , x , x , x ,5 x ,5 x ,5 x , x , x , x ,5 x ,5 x , x /TiN d 1 h8 x l 1 l mm mm 8, x , x ,5 x ,5 x ,5 x , x , x , x ,5 x , x , x , x , x , x Al<1%Si Al>1%Si Cu St<52N St<75N St<9N St<11N St<12N St<14N <45HRC <55HRC <6HRC <67HRC VA-steel<9N VA-steel>9N Ti-alloys GG(G) plastics

28 Twist drills Cone envelope grind. Surface-treated, this reduces tendency of the machined material to stick to the machining tool and improves chip removal. 158 ground for steel to 9 N/mm 2, cast iron, aluminium alloys, brass, bronze. Twist Drills with Morse Taper Shanks 151 precision rolled for steel to 8 N/mm 2, cast iron, aluminium alloys, bronze, brass. Economically-priced version. 345 N drill for highest demands. Drill for production. d 1 h8 l 2 l 1 MK , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , d 1 h8 l 2 l 1 MK , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , Continuation. 1.28

29 Twist Drills with Morse Taper Shanks Continuation. d 1 h8 l 2 l 1 MK , , , , , d 1 h8 l 2 l 1 MK , , , , N Al<1%Si Al>1%Si Cu St<52N St<75N St<9N St<11N St<12N St<14N 45HRC 55HRC 6HRC 67HRC VA-steel<9NVA-steel>9N Ti-alloy GG(G) plastics Web-thinned chisel edge. drill for highest demands T /TiN for even longer service life in steel to 9 N/mm 2, cast iron, aluminium alloys, bronze, brass. Twist Drills with Morse Taper Shanks E surface-treated for steel to 12 N/mm 2 and cast iron. Reduced tendency of the machined material to stick to the machining tool and improved chip removal. Reinforced core E with special geometry for VA-steels and materials with a strain hardening tendency. N N VA TiN -E -E 345 VA T d 1 h8 l 2 l 1 MK , , , , , , , , , , , , , , , , , , , , , , , T d 1 h8 l 2 l 1 MK , , , , , , , , , , , , , , , , , , , , , , Al<1%Si Al>1%Si Cu St<52N St<75N St<9N St<11N St<12N St<14N 45HRC 55HRC 6HRC 67HRC VA-steel<9N VA-steel>9N Ti-alloy GG(G) plastic

30 Twist drills Core drills Multiplex holder 161 T - Surface-treated, this reduces the tendency of the machined material to stick to the machining tool and improves chip removal. - Greater than Ø 14 mm web-thinned - Extended cutting section relative to 345 Long twist drill (bushing drill) with Morse taper shank ground for for steel to 9 N/mm 2, cast iron, graphite. For drilling through bushings. 341 N d 1 h8 l 2 l 1 MK 161 1, , , , , , , , , , , d 1 h8 l 2 l 1 MK , , , , , , , , , , , Al<1%Si Al>1%Si Cu St<52N St<75N St<9N St<11N St<12N St<14N <45HRC <55HRC <6HRC <67HRC VA-steel<9N VA-steel>9N Ti-alloys GG(G) plastics T - Reinforced core - Shallow flute profile - Web-thinned - To Ø 16 mm, nitrided lands and bare flutes. Greater than this diameter, special thermal treatment for increased wear resistance and reduced tendency of the machined material to stick to the machining tool Extra long twist drill with Morse taper shank ground for for steel to 9 N/mm 2, cast iron, graphite, aluminium alloy, brass, bronze. For drilling boreholes with a diameter of up to 1 x D without chip removal. 187 Reihe 1, 2, FN d 1 h8 x l 1 l 2 MK 1621 mm mm 8 x x x x x x x x x x x x x x d 1 h8 x l 1 l 2 MK 1621 mm mm 16 x x x x x x x x x x x x x Al<1%Si Al>1%Si Cu St<52N St<75N St<9N St<11N St<12N St<14N <45HRC <55HRC <6HRC <67HRC GG(G) plastics

31 Highly rounded heels - Surface-treated for reduced tendency of the machined material to stick to the machining tool and improved chip removal. ground for machining standard duty materials to 9 N/mm 2. d 1 h8 l 2 l 1 MK , , , , , , , , , Core drills with Morse taper shank Advantage: For drilling out ovalised holes; holes that are not flush can be compensated. The diameter to be core-drilled should be at least 3/4 of the core drilling Ø. d 1 h8 l 2 l 1 MK , , , , , , , , , Z 3 N d 1 h8 l 2 l 1 MK , , , , , , , , , Al<1%Si Al>1%Si Cu St<52N St<75N St<9N St<11N St<12N St<14N <45HRC <55HRC <6HRC <67HRC VA-steel<9NVA-steel>9NTi-alloys GG(G) plastics Info Are you familiar with the Multiplex drilling system from HARTNER? T The tool system with interior-cooled holders in different lengths, as well as interchangeable cutting tips, consequently - No re-sharpening - Always the original grind - Length always remains constant Each holder drills with tips in different diameters and cutting materials, such as coated -E PM and solid carbide depending on the material to be machined. Drill range von Ø 9,7 to 65 mm often up to 7 x d. This tool is not suitable for drilling out precast or pre-drilled holes. What you previously drilled conventionally, you now drill with the MULTIPLEX DRILLING SYSTEM - Faster - More accurately - Better - Cheaper The MULTIPLEX Drilling System offers many advantages: - No re-sharpening costs - The coating advantage remains fully intact - High machining performance and optimal service life thanks to interior cooling - Constant tool length - Pre-adjustment times and readjustment for NC machines are dispensed with - Reduced stock keeping costs Multiplex exchangeable blades - twist drills further development as a special tool for the work steps - Drilling - Spot-facing - Planing - Chamfering - Hollowing-out - Countersinking The MULTIPLEX Drilling System helps to reduce your costs! With internal coolant feed. With straight shank, right-hand cut. Up to drilling Ø 35 mm hardened and nickel-plated. Above nickel-plated. Without cutting tip. Point angle: - To Ø 25,4 = Over Ø 25,4 = 132 Web-thinned: Special shape with short web-thinned chisel edge. For drilling steel and cast steel, alloyed and unalloyed, with a strength of up to approx. 11 N/mm 2, grey cast iron, malleable cast iron, spheroidal cast iron, sintered iron, German silver, bronze, brass Holder with straight shank 3 x D T 1649 For drilling l 2 l 1 D 1 d 2 B Torx screws 1649 Ø D G 9,7-11, ,5 2 2,5 M2, x ,71-13, ,5 2 2,5 M2, x ,41-16, , 2 3,5 M2,5 x ,41-18, , 2 3,5 M2,5 x ,91-22, ,5 2 4, M3, x ,41-25, , 2 4, M3, x ,41-29, , 32 5, M3,5 x ,1-35, , 32 5, M3,5 x ,1-45, , 32 7, M4, x ,1-55, , 4 7, M4, x ,1-65, , 4 7, M4, x D G D₁ d2 B Continuation. 1.31

32 Multiplex holder 165 Holder with straight shank 5 x D T 165 For drilling l 2 l 1 D 1 d 2 B Torx screws 165 Ø D G 9,7-11, ,5 2 2,5 M2, x ,71-13, ,5 2 2,5 M2, x ,41-16, , 2 3,5 M2,5 x ,41-18, , 2 3,5 M2,5 x ,91-22, ,5 2 4, M3, x ,41-25, , 2 4, M3, x ,41-29, , 32 5, M3,5 x ,1-35, , 32 5, M3,5 x ,1-45, , 32 7, M4, x ,1-55, , 4 7, M4, x ,1-65, , 4 7, M4, x Holder with straight shank 7 x D D G D₁ d2 B T 1651 For drilling l 2 l 1 D 1 d 2 B Torx screws 1651 Ø D G 9,7-11, ,5 2 2,5 M2, x ,71-13, ,5 2 2,5 M2, x ,41-16, , 2 3,5 M2,5 x ,41-18, , 2 3,5 M2,5 x ,91-22, ,5 2 4, M3, x ,41-25, , 2 4, M3, x ,41-29, , 32 5, M3,5 x ,1-35, , 32 5, M3,5 x ,1-45, , 32 7, M4, x ,1-55, , 4 7, M4, x ,1-65, , 4 7, M4, x Exchangeable Blades for Multiplex System D G D₁ d2 B - Facet ground E-PM/TiN for steel to 12 N/mm 2, cast iron, aluminium. With chip divider groove for short chips E-PM/fire-coating for longer service life in steel to 12 N/mm 2, cast iron, aluminium, brass, bronze. With chip divider groove for short chips. -E-PM TiN -E-PM FIRE Solid carbide/fire-coating for even longer service life and performance even in steel to 48 HRC and hardened cast iron. With land, without chip divider groove. H22 FIRE E-PM/TiN -E-PM/fire H 22/fire Ø B mm mm 1, 2, ,2 2, ,5 2, , 2, , 2, ,5 2, ,75 2, , 2, ,5 3, ,75 3, , 3, ,25 3, ,5 3, E-PM/TiN -E-PM/fire H 22/fire Ø B mm mm 14,75 3, , 3, ,25 3, ,5 3, ,75 3, , 3, ,25 3, ,5 3, , 3, ,5 3, ,75 3, , 3, ,25 3, Continuation. 1.32

33 Exchangeable Blades for Multiplex System Continuation. -E-PM/TiN -E-PM/fire H 22/fire Ø B mm mm 18,5 3, ,75 3, , 4, ,5 4, ,75 4, , 4, ,25 4, 657 2,5 4, , 4, ,25 4, ,5 4, ,75 4, , 4, ,5 4, E-PM/TiN -E-PM/fire H 22/fire Ø B mm mm 23, 4, ,5 4, , 4, ,25 4, ,5 4, , 4, , 5, , 5, 69 28, 5, , 5, 7 3, 5, 75 33, 5, 72 34, 5, , 5, 73 Al<1%Si Al>1%Si Cu St<52N St<75N St<9N St<11N St<12N St<14N <45HRC <55HRC <6HRC <67HRC VA-steel<9N VA-steel>9N Ti-alloys GG(G) plastics T - Facet ground -E-PM 132 TiAIN -E-PM/TiAlN for materials to 12 N/mm Exchangeable Blades for Multiplex System -E-PM/TiAlN Ø B 1672 mm mm , , , E-PM/TiAlN Ø B 1672 mm mm E-PM/TiAlN Ø B 1672 mm mm E-PM/TiAlN Ø B 1672 mm mm Al<1%Si Al>1%Si Cu St<52N St<75N St<9N St<11N St<12N St<14N <45HRC <55HRC <6HRC <67HRC VA-steel<9N VA-steel>9N Ti-alloys GG(G) plastics T Pack = 5 pcs. TORX clamp screws For Multiplex exchangeable blade twist drills cat.-no ff Designation For drilling TORX 1674 mm size M 2, x T 6 21 M 2,5 x 5 > T 7 22 M 2,5 x 7 > T 7 23 M 3, x 6 > T 9 24 Designation For drilling TORX 1674 mm size M 3, x 8 > T 9 25 M 3,5 x 1 > T M 4, x 15 > T

34 Step drills 184 Step drills T - Countersink angle 9 - With straight shank - Web-thinned chisel edge and surface treatment For producing threaded core holes and countersinks in accordance with 336 Part 1. Countersinks for through-holes in accordance with EN ground for steel to 9 N/mm 2, aluminium alloys, brass, bronze l 3 N d for d 1 x d 2 l 3 l 2 l Thread mm M 3 2,5 x 3,4 8, M 4 3,3 x 4,5 11, M 5 4,2 x 5,5 13, Step drills for d 1 x d 2 l 3 l 2 l Thread mm M 3 3,4 x 6, M 4 4,5 x 9, M 5 5,5 x 11, M 6 6,6 x 13, M 8 9, x 17, Al<1%Si Al>1%Si Cu St<52N St<75N St<9N St<11N St<12N St<14N <45HRC <55HRC <6HRC <67HRC VA-steel<9N VA-steel>9N Ti-alloys GG(G) plastics T - Countersink angle 9 - With straight shank - Web-thinned chisel edge and surface treatment For producing screw through-holes EN 2273, screw-head countersinks shape A medium in accordance with 74 Part 1. Screw countersinks 963 to 966. ground for steel to 9 N/mm 2, aluminium alloys, brass, bronze Al<1%Si Al>1%Si Cu St<52N St<75N St<9N St<11N St<12N St<14N <45HRC <55HRC <6HRC <67HRC VA-steel<9N VA-steel>9N Ti-alloys GG(G) plastics l 3 9 for d 1 x d 2 l 3 l 2 l Thread mm M 6 5, x 6,6 16, M 8 6,8 x 9, 21, M 1 8,5 x 11, 25, N d Step drills T - Countersink angle 18 - Web-thinned chisel edge and surface treatment For producing screw through-holes EN 2273, screw-head countersinks shape H, J and K. Version medium in accordance with 74 Part 2. Cheese head screws in accordance with 84, 912, 6912, 7513, ground for steel to 9 N/mm 2, cast iron, aluminium alloys, brass, bronze With straight shank With Morse taper shank. Straight shank Morse taper shank for d 1 x d 2 l 3 l 2 l 1 shank Thread mm MT M 3 3,4 x 6, M 4 4,5 x 8, M 5 5,5 x 1, M 6 6,6 x 11, M 8 9, x 15, M 8 9, x 15, M 1 11, x 18, M 1 11, x 18, M 12 13,5 x 2, M 16 17,5 x 26, M 2 22, x 33, l l N d2 d

35 Short step drills T - With straight shank - Web-thinned chisel edge ground for steel to 9 N/mm 2, cast iron, aluminium alloys, brass, bronze Countersink angle 9. For threaded core holes 336 Part 1. Countersinks for through-holes EN 2273 medium Countersink angle 9. For screw through-holes EN Countersinks 74 Part 1 fine, countersunk screws EN ISO 29 and N Countersink angle 18. For screw through-holes EN Screw-head countersinks, shape H, J, K Part 2 medium. Cheese head screws EN ISO 4762, EN ISO 127, 6912, 7513, for d 1 x d 2 l 3 l 2 l thread mm M 3 2,5 x 3,4 8, M 4 3,3 x 4,5 11, M 5 4,2 x 5,5 13, M 6 5, x 6,6 16, M 8 6,8 x 9, 21, M 1 8,5 x 11, 25, M 12 1,2 x 13,5 3, M 3 3,2 x 6, 9, M 4 4,3 x 8, 11, M 5 5,3 x 1, 13, M 6 6,4 x 11,5 15, M 8 8,4 x 15, 19, M 1 1,5 x 19, 23, M 3 3,4 x 6, 9, M 4 4,5 x 8, 11, M 5 5,5 x 1, 13, M 6 6,6 x 11, 15, M 8 9, x 15, 19, M 1 11, x 18, 23, l 3 d2 18 l 3 d Al<1%Si Al>1%Si Cu St<52N St<75N St<9N St<11N St<12N St<14N <45HRC <55HRC <6HRC <67HRC VA-steel<9N VA-steel>9N Ti-alloys GG(G) plastics Short step drills - With straight shank - Diameter tolerance h8 For thread core holes. For economically producing boreholes and countersinkings in one work step. Solid carbide/tiain-coated Countersink angle Countersink angle 18. For through-holes. 9 for d 1 x d 2 l 3 l 2 l 1 shank Ø 1863 thread mm mm M 3 2,5 x 3,4 8, , 11 M 4 3,3 x 4,5 11, , 12 M 5 4,2 x 5,5 13, , 13 M 6 5, x 6,6 16, , 14 M 8 6,8 x 9, 21, , 15 M 1 8,5 x 11, 25, , 16 M 12 1,2 x 13,5 3, , 17 l 3 d2 l 3 d for d 1 x d 2 l 3 l 2 l 1 shank Ø 1864 thread mm mm M 3 3,4 x 6, , 11 M 4 4,5 x 8, , 12 M 5 5,5 x 1, , 13 M 6 6,6 x 11, , 14 M 8 9, x 15, , 15 M 1 11, x 18, , 16 9 VHM TiAIN Al<1%Si Al>1%Si Cu St<52N St<75N St<9N St<11N St<12N St<14N <45HRC <55HRC <6HRC <67HRC VA-steel<9N VA-steel>9N Ti-alloys GG(G) plastics

36 Centre drills Centre drills - Shape A 6 - Double-sided - Spiral flutes - Relief-ground - Simple centre hole without protective countersink, with large surface contact of the workpiece on the lathe centre For producing centre holes in compliance with 332 when machining standard-duty materials such as steel, cast iron, non-ferrous metals and light metals. Suitable for particularly heavy workpieces using live lathe centres. Centre drill with Ø,5 and,8 mm, single-ended E E/TiN-coated. -E -E TiN -E TiAIN 333A Form 333A A (L) E/TiAlN-coated. d2 -E -E/TiN -E/TiAlN d 1 h7 d 2 l ,5 3,15 25, 1 pcs ,8 3,15 25, 1 pcs , 3,15 31, 1 pcs L 1, 4, 12, 14 1,25 3,15 31, 1 pcs ,6 4, 35, 1 pcs L 1,6 5, 12, 17 2, 5, 4, 1 pcs L 2, 6, 12, 19 2,5 6,3 45, 1 pcs L 2,5 8, 12, 111 3,15 8, 5, 1 pcs L 3,15 1, 12, 113 4, 1, 55, 1 pcs L 4, 1, 12, 119 5, 12,5 63, L 5, 14, 12, 12 6,3 16, 71, , 2, 8, , 25, 1, Al<1%Si Al>1%Si Cu St<52N St<75N St<9N St<11N St<12N St<14N <45HRC <55HRC <6HRC <67HRC VA-steel<9N VA-steel>9N Ti-alloys GG(G) plastics centre drill set - Shape A 6 - Short - Countersink angle 6. For centre holes without protective countersink in accordance with Set contents: 3 pieces 1,6 x 4, mm 3 pieces 2, x 5, mm 3 pieces 2,5 x 6,3 mm 3 pieces 3,15 x 8, mm 2 pieces 4, x 1, mm 1 piece 5, x 12,5 mm Set contents part A Form 333A A

37 Shape A 6 - Double-sided - Left-hand cut - Spiral flutes Centre drill, left-hand cut - Relief-ground For left turning machine tools.. d 1 h7 d 2 l , 3,15 31, 1 pcs. 13 1,6 4, 35, 1 pcs. 16 2, 5, 4, 1 pcs. 18 2,5 6,3 45, 1 pcs. 11 3,15 8, 5, 1 pcs , 1, 55, 1 pcs , 12,5 63, A Form 333A A d2 Al<1%Si Al>1%Si Cu St<52N St<75N St<9N St<11N St<12N St<14N <45HRC <55HRC <6HRC <67HRC VA-steel<9N VA-steel>9N Ti-alloys GG(G) plastics Centre drills - Double-sided (Ø,5 and,8 single-sided) - Spiral flutes - Relief-ground Shape A with bead 6 - Centre hole without protective countersink - With annular bead that forms an additional lubricant space Suitable for high-speed workpieces when using dead lathe centres Shape R 6 - Centre hole with radius produces a ring-shaped contact surface of the workpiece on the lathe centre with the advantages of a protective countersink Particularly suitable for workpieces subject to deformation stress during machining Shape B 6/12 - Centre hole with conical protective countersink - Large surface contact of the workpiece on the lathe centre Particularly suitable for workpieces or tools, which often need to be clamped between lathe centres. Form A Form R Form B d2 d2 Shape A Shape R d 1 h7 d 2 l ,5 3,15 25, 1 pcs. 11,8 3,15 25, 1 pcs. 12 1, 3,15 31, 1 pcs ,25 3,15 31, 1 pcs. 15 1,6 4, 35, 1 pcs , 5, 4, 1 pcs ,5 6,3 45, 1 pcs ,15 8, 5, 1 pcs , 1, 55, 1 pcs , 12,5 63, ,3 16, 71, Shape B d 1 h7 d 2 l ,6 6,3 45, 1 pcs. 13 2, 8, 5, 1 pcs. 14 2,5 1, 55, 1 pcs. 15 3,15 11,2 62, 1 pcs. 16 4, 14, 69, 1 pcs. 17 5, 18, 77, 18 6,3 2, 8, 19 6 Al<1%Si Al>1%Si Cu St<52N St<75N St<9N St<11N St<12N St<14N <45HRC <55HRC <6HRC <67HRC VA-steel<9N VA-steel>9N Ti-alloys GG(G) plastics

38 12 9 Centre drill NC spot drills 188 Solid carbide centre drills - Shape A 6 - Simple centre hole without protective countersink - With large surface contact of the workpiece on the lathe centre For producing centre holes when machining heavyduty materials, such as steel with high-strength, different cast irons and aluminium with high content of silicum. Suitable for particularly heavy workpieces using live lathe centres. Norm Solid carbide K1/K Form A VHM K1/K2 d2 K1/K2 d 1 h7 d 2 l , 3,15 31,5 13 1,25 3,15 31,5 14 1,6 4, 35,5 15 2, 5, 4, 16 K1/K2 d 1 h7 d 2 l ,5 6,3 45, 17 3,15 8, 5, 18 4, 1, 56, 19 5, 12,5 63, 11 Al<1%Si Al>1%Si Cu St<52N St<75N St<9N St<11N St<12N St<14N <45HRC <55HRC <6HRC <67HRC VA-steel<9N VA-steel>9N Ti-alloys GG(G) plastics NC spot drills - With straight shank - Extremely short flutes - Without lands - Special drill with weak core For drilling steel and cast steel, both alloyed and unalloyed, up to a strength of approx. 1 N/mm 2, grey cast iron, malleable cast iron, spheroidal cast iron, sintered iron, German silver, graphite, short-chipping aluminium alloys, die-casting, ductile brass. Particularly suitable for accurate spot and countersink-drilling on NC- und CNCdriven machines, jig drilling machines etc. d1 l 2 l E -E TiCN -E Not suitable for deep holes! TiN-coated NC spot drills, with different point angle, extended version, or with MT shank, available on request. d1 l 2 l 1 -E TiCN E 9 -E/TiCN 9 -E 12 -E/TiCN 12 d 1 h 6 l 2 l , , , , , , , , , Al<1%Si Al>1%Si Cu St<52N St<75N St<9N St<11N St<12N St<14N <45HRC <55HRC <6HRC <67HRC VA-steel<9N VA-steel>9N Ti-alloys GG(G) plastics

39 Long NC spot drills - Straight shank - Extremely short flutes, without lands For drilling steel and cast steel, both alloyed and unalloyed, up to a strength of approx. 1 N/mm 2, grey cast iron, malleable cast iron, spheroidal cast iron, sintered iron, German silver, graphite, short-chipping aluminium alloys, die-casting, ductile brass. Not suitable for deep holes! E E/TiCN-coated. -E -E TiCN E 9 -E/TiCN 9 d 1 h6 l 2 l Al<1%Si Al>1%Si Cu St<52N St<75N St<9N St<11N St<12N St<14N <45HRC <55HRC <6HRC <67HRC VA-steel<9N VA-steel>9N Ti-alloys GG(G) plastics Solid carbide NC spot drills ß - Straight shank - Extremely short flutes, without lands - Surface grind - Special drill with weak core Particularly suitable for accurate spot and countersink drilling on NC and CNC-driven machines, jig drilling machines etc. For drilling grey cast iron, hardened cast iron, short-chipping malleable cast iron, hardened steel, non-ferrous metal, plastics etc. VHM 9 K1/K2 Carbide, type K1/K K1/K2 9 d 1 h8 l 2 l Al<1%Si Al>1%Si Cu St<52N St<75N St<9N St<11N St<12N St<14N <45HRC <55HRC <6HRC <67HRC VA-steel<9N VA-steel>9N Ti-alloys GG(G) plastics Performance requires quality. For example, with the zero-point clamping system from ATORN. Optimal positioning accuracy Maintenance-free High, holding forces, pull-in forces and closure forces Performance requires quality. 1.39

40 NC spot drills Taper pin drills ß - Straight shank - Spiral flutes Spot drilling and countersinking with NC-machines, for cast iron, malleable cast iron, non-ferrous light metal, abrasive plastics. Solid carbide NC spot drills Solid carbide finest grit/tialn-coated d 1 h6 l 2 l HA VHM TiAIN Al<1%Si Al>1%Si Cu St<52N St<75N St<9N St<11N St<12N St<14N <45HRC <55HRC <6HRC <67HRC VA-steel<9N VA-steel>9N Ti-alloys GG(G) plastics Taper pin drills T - Straight shank with driver in compliance with 189 D For drilling steel and cast steel, both alloy and carbon up to a strength of approx. 1 N/mm 2, grey cast iron, malleable cast iron, etc. For drilling taper holes for taper pins 1 and 7978 in one operation. (For finish machining, use taper pin reamers cat.-no ). The diameter d 1 of the taper pin drill refers to the nominal diameter of the taper pin. 1898A 1:5 1: d2 d 1 h9 l 2 l 1 d mm , , , , , , 11 Al<1%Si Al>1%Si Cu St<52N St<75N St<9N St<11N St<12N St<14N <45HRC <55HRC <6HRC <67HRC VA-steel<9N VA-steel>9N Ti-alloys GG(G) plastics L ARGE SELECT I O N E A S Y S E A R C H D o n t f o r g e t! C ATA ALOG UE VOLUME [2] The universal c a t a l o g u e f o r tools and machines. 1.4

41 Our new services brand for everything to do with your tools. The ComBee brand stands for innovation and the highest quality in the area of self-service machines. Our responsible technical consultants in our field service organisation would be pleased to advise you with regard to the versatile implementation possibilities in your company.

42 Boring and Deburring Tool Set Step drills Info boring and deburring tool set (step drill) Diameter tolerance +/-,13 mm. For boring holes in sheeting with a thickness of,4 to 3, mm of almost all alloys, stainless steel, grey cast iron, aluminium, brass, plastics and fibreglass.. Spare cooling lubricant stick see cat.-no Consisting of 1 drilling tool and and 1 deburring tool MC 1M / MC 2M and MC 3M, with cooling lubricant in metal case.. Boring and Deburring Tool Set Spare cooling lubricant stick see cat.-no Hole Ø 1918 mm Size M1 - M6 and PG 29 without clamping stem (for clamping stems see cat.-no. 1921). 1) especially for electricians, for use in electric hand drills. 2) for thread size PG. Step Drills (3 Cutting Blades) 1919 Size Number of Dimension table for drill diameter Inner shank to material 1919 blades mm Taper Ø mm thickness mm M1 3 5,5 / 8,5 / 11,5 / 14,5 / 17,5 / 2,5 / 23,5 / 26,5 / 29,5 / 32,5 / 35,5 B M2 3 6 / 9 / 12 / 15 / 18 / 21 / 24 / 27 / 3 / 33 / 36 B M4 3 7 / 1 / 13 / 16 / 19 / 22 / 25 / 28 / 31 / 34 / 37 B M5 3 7,5 / 1,5 / 13,5 / 16,5 / 19,5 / 22,5 / 25,5 / 28,5 / 31,5 / 34,5 / 37,5 B M6 3 8 / 11 / 14 / 17 / 2 / 23 / 26 / 29 / 32 / 35 / 38 B PG21 1) 3 12,5 (PG7) / 15,2 (PG9) / 18,6 (PG11) / 2,4 (PG13,5) / 22,5 (PG16) / 25,8 / 28,3 (PG21) / 3,5 - B PG29 1) 3 12,5 (PG7) / 15,2 (PG9) / 18,6 (PG11) / 2,4 (PG13,5) / 22,5 (PG16) / 25,8 / 28,3 (PG21) / 3,5 / 33,6 / 37, (PG29) B PGT 1) 2) 3 11,4 (PG7) / 14, (PG9) / 17,25 (PG11) / 19, (PG13,5) / 21,25 (PG16) / 24,5 /26,75 (PG21) Clamping stems for step drills cat.-no Shank for sizes M1- M6 and PG 29 (cat.-no and ) MT clamping stems, see HHW catalogue volume 1 cat.-no Clamping stem for cylindrical taper 1921 Size Ø mm M 1 - M 5 9,5 B 1 11 M 6 + PG 29 12,5 B

43 1924 Step Drills (2 Cutting Blades) 1924 Size No. of cutting Hole diameter Shank for material 1924 blades mm Ø mm thickness mm MC 1M 2 4 / 5 / 6 / 7 / 8 / 9 / 1 / 11 / MC 2M 2 1 / 11 / 12 / 13 / 14 / 15 / 16 / 17 / 18 / 19 / MC 3M 2 2 / 21 / 22 / 23 / 24 / 25 / 26 / 27 / 28 / 29 / MC 4M 2 4 / 6 / 8 / 1 / MC 5M 2 6 / 8 / 1 / 12 / 14 / 16 / 18 / 2 / 22 / MC 7M 2 4 / 6 / 8 / 1 / 12 / 14 / 16 / 18 / MC 1M 2 4 / 6 / 8 / 1 / 12 / 14 / 16 / 18 / 2 / 22 / 24 / 26 / 28 / Step drills For through-holes. Especially for boring holes in sheeting, e.g. -Greenlee Size Hole diameter Shank for material 1926 mm/inches Ø mm thickness mm MC 521M 5 mm / 7 mm / 3/8 inch / 7/16 inch / 13 mm / 15 mm / 3/4 inch / 21 mm Step drills With 2 spiral flutes (DBGM) and -edge breaker- (DBGM) deburring zone, as well as ROTASTOP (DBGM) comfort shank. Both steps (6 mm for corehole and 3 mm for through-hole) on one tool. Thread core-hole (6 mm steps) Ø / thread 7, / - 1,5 / M 12 x 1,5 14,5 / M 16 x 1,5 18,5 / M 2 x 1,5 23,5 / M 25 x 1,5 3,5 / M 3 x 1,5 For burr-free drilling and reaming of cable screw connections in compliance with EN For machining of splice boxes, installation sockets, distributor housings, terminal boxes, control cabinets, switching devices and control devices, enclosures. Through hole (3 mm steps) Ø / thread 12,5 / M 12 x 1,5 16,5 / M 16 x 1,5 2,5 / M 2 x 1,5 25,5 / M 25 x 1,5 32,5 / M 3 x 1, TiN-coated 21 TiN-coated 31 -E TiN -E TiAIN With straight shank. Boring steps in precise 1 mm increments. For drilling straight holes up to 4 mm material thickness of almost all materials such as steel, cast metal, brass, plastics and fibreglass. No pre-drilling necessary. Step Drills (6 Cutting Blades) 1928 Size No. of cutting Hole diameter Shank for material 1928 blades mm Ø mm thickness mm TMC / 31 / 32 / 33 / 34 / 35 / 36 / 37 / 38 / 39 / TMC / 41 / 42 / 43 / 44 / 45 / 46 / 47 / 48 / 49 / TMC / 51 / 52 / 53 / 54 / 55 / 56 / 57 / 58 / 59 /

44 Slabbing Cut Drill Reamers Milling Drills Spot-Weld Milling Cutters Core Drills 1934 ß With straight shank. For drilling 3-3,5 mm, consisting of 1 drill in each size 1, 2 and 3, in plastic case. For drilling and reaming holes in thin material free of burrs and chatter marks in one operation. For annealed sheet steel, stainless sheet steel, car-body sheeting, non-ferrous metals, thin-walled pipes and plastics such as PVC, Plexiglas, Resopal etc., also for hardboard, plywood etc. Slabbing Cut Drill Reamer (Sheet Metal Drills) Sets -E E/TiN-coated. -E E TiN For drilling up to the edge without deformation. Cooling lubricant stick see cat.-no E 21 -E/TiN ß With straight shank. For drilling and reaming holes in thin material free of burrs and chatter marks in one operation. For annealed sheet steel, stainless sheet steel, car-body sheeting, non-ferrous metals, thin-walled pipes and plastics such as PVC, Plexiglas, Resopal etc., also for hardboard, plywood etc. Cooling lubricant necessary! Slabbing Cut Drill Reamers (Sheet Metal Drills) E E/TiN-coated Cooling lubricant Without silicone, contents 25 ml. For lubricating all contact faces during drilling and thread cutting. -E -E/TiN Coolant lubricating stick Size Hole Ø Shank Ø mm mm , , , , , , , E -E TiN ß With straight shank. For drilling and cutting out any contour required in all kinds of metal sheeting; also suitable for wood, Resopal and other plastics.. Universal Drill/Milling Cutter Best speed approx /min. For material that binds (zinc, aluminium etc.), occasionally dip the tool into a lubricant. For use in power hand drills. Cooling lubricant stick see cat.-no Ø 194 mm 6,

45 1942 Spot-Weld Milling Cutters The milling head is reversible, the milling depth can be adjusted. For loosening spot-welded sheeting without deformation or tear. For sheet metal processing, car body workshops, industry etc.. Best speed approx. 9 1/min Milling crown Ø 1942 mm Milling cutter 1 11 Spare crown Co Core Drills (Weldon) The core drill machines only a small groove, the residual core is ejected unmachined drilling time reduced by up to 4x, long service life low wear. All core drills with Weldon shank 19 mm for direct mounting or for mounting in Morse taper mounts MK-2/AMK-3 with interior cooling. Suitable for magnetic core drills (see HHW catalogue volume 2 cat.-no. 96) or for table and column drilling machines. -Co. Carbide-tipped core drills or drills with other cutting depths available on request Cutting depth 25 mm Cutting depth 5 mm mm 5 mm Ø mm mm 5 mm Ø mm mm 5 mm Ø mm Accessories for Core Drills 1957 Clamping stems With automatic interior cooling and nipple for coolant hose. Delivered in plastic case. For mounting -Co core drills (cat.-no ) Spare ejector pins For -Co core drills from Ø 12 up to 5 mm Clamping stem Ejector pin Size for magnetic core drill for cutting depth for Ø cat. no. mm mm MT MT

46 QuickIN core drills 1959 QuickIN core drills With QuickIN mount. The core drill machines only a small groove, the residual core is ejected unmachined drilling time reduced by up to 4x, long service life low wear. For cutting depth to 35 mm. For direct mounting in core drills KBM 65 Q/65 QF/65 U / KBM 5/5 U/5 A (see HHW Catalogue volume 2 cat. no. 957), for KBM 65/65 F (predecessor design) via QuickIN clamping stem (cat.-no. 1962) and for table and column drilling machines via QuickIN clamping stems (cat.-no. 1964) Core drills, single Core drills, single Carbide. HM Core drills with other diameters and cutting depths available on request HM Set contents core hole Ø 1959 mm 5-part 14 / 18 / 22 / 32 carbide 191 HM Hole Ø Total length mm mm HM Hole Ø Total length mm mm

47 1961 QuickIN PLUS core drills and centre drills Y With QuickIN PLUS mount - Maximum service life thanks to carbide tip - Outstanding machining performance in all standard metals - Drill diameter Ø steel to 25 mm / 1 inch - Drill Ø alu to 3 mm / 1.3/16 inch For cutting depth to 2 mm. For direct mounting in the core drill KBH 25 (see HHW Catalogue volume 2 cat.-no ). Carbide Centre drills Other accessories available on request: - Collet chucks and split chucks for thread-cutting - Chip pans - Cutting spray - Extension Also available on request: - Other drill Ø (19/16-1.3/16 inch) - Carbide core drills coated (14-3 mm, 9/16-1.3/16 inch) - Carbide compass saws (14-54 mm, 9/16-2.1/8 inch) - HM compass saws for pipes (21-54 mm, 7/8-2.1/8 inch) Core Drills Drill Ø 1961 mm Centre drills for drill Ø 1961 mm Core Drills Drill Ø 1961 mm Core Drills (with Thread) Y With thread M 18 x 6 P 1,5. The core drill machines only a small groove, the residual core is ejected unmachined drilling time reduced by up to 4x, long service life low wear. For cutting depth to 5 mm. For direct mounting in core drills KBM 65/65 F (predecessor design), for KBM 65 Q/65 QF (see HHW catalogue volume 2 cat.-no. 957) via QuickIN clamping stem (cat.-no. 1962) and adapter (cat.-no. 1965) and for table column drilling machines via QuickIN clamping stems (cat.-no. 1964) and adapters (cat.-no. 1965). Carbide. Core drills with other cutting depths available on request. 196 Drill Ø Total length 196 mm mm Drill Ø Total length 196 mm mm Drill Ø Total length 196 mm mm

48 Accessories for QuickIN core drills 1962 QuickIN Clamping Shank (Core Drilling Machines) Y - With Morse taper MT 3 - Integrated coolant feed For core drills KBM 65/65 F (predecessor design) and KBM 65 Q/65 QF (see HHW Catalogue volume 2 cat.-no. 957). For direct mounting of QuickIN core drills (cat.-no. 1959) or by means of adapter (cat.-no. 1965) of core drills with thread (cat.-no. 1959) or with Weldon shank (cat.-no. 1955) Shank for core drills 1962 Drill Ø mm MT QuickIN Clamping Shanks (Table and Column Drilling Machines) Y - With Morse taper - Hand pump for external coolant feed For table and column drilling machines. For direct mounting of QuickIN core drills (cat.-no. 1959) or by means of adapter (cat.-no. 1965) of core drills with thread (cat.-no. 196) and/or with Weldon shank (cat.-no. 1955) Shank for core drills 1964 Drill Ø mm MT MT QuickIN Adapters Y For core drills KBM 65/65 F (predecessor design), KBM 65 Q/65 QF (see HHW Catalogue volume 2 cat.-no. 957) and table and column drilling machines Output M 18 x 6 P 1,5. For mounting core drills with thread (cat.-no.196) Output Weldon. For mounting core drills with Weldon shank (cat.-no.1955) Output 1965 M 18 x 6 P 1,5 11 Weldon Centring Pins Y For the ejection of the uncut remaining core part For core drills with QuickIN mount (cat.-no.1959) For core drills with thread (cat.-no. 196) for core drill Length 1966 with mount mm QuickIN Thread