WARE HANDLING SERVO MECHANISM SERVO INVERT SERVO TAKE-OUT BDF A.P. PUSHER

Transcription

1 WARE HANDLING SERVO MECHANISM SERVO INVERT SERVO TAKE-OUT BDF A.P. PUSHER

2 WARE HANDLING SERVO MECHANISM BDF, first in the world on the 1992, has designed and implemented in the I.S. Machines the Servo Invert and Take-Out mechanisms with the objective to reduce the defects in the finish and neck area. The result of this engineering program has been the realisation of a new state-of-the-art on the glass technology for the electronic control systems and for the servo mechanisms controlled by brushless servo motors with mathematical interpolation motion profiles.

3

4 SERVO INVERT Electric cams with interpolation Sinusoidal acceleration deceleration Process control during the motion Easy set-up with computer or hand terminal Check of end-stroke positions Defects reduction on container finish Productivity increase (constant setup) Reduction of manual adjustments Elimination of hydraulic cushioning Very low energy consumption due to the energy recovery control Main Data Minim. Revert Motion Time = 335 msec Invert Position Accuracy= 0.34 mm on the DG 5 1/2 invert arm top Invert Motor type= hollow shaft brushless motor BDF patent (very high reliability) Transmission type= ball-screw with ceramic technology (low inertia, high efficiency and reliability) Self control system to check wrong position set-up Mechanical Features High-performance mechanical drive Lower energy consumption Fewer mechanical components Servo invert interchangeable with the standard pneumatic mechanism without upper-plate modification Servo invert mechanism with hollow shaft brushless motor and transmission with ball-screw In ceramic material: low inertia, high efficiency, high reliability Use of standard equipment Elimination of constant cushions and mechanical adjustments Electrical Features Control up to 12 stand-alone or integrated sections; Repeatable accurate positioning Data programmed via computer and hand terminal; Jog function for mechanism run from hand terminal and local section control Servo mechanism interference and anti-impact system to improve safety Servo mechanism alarm system for easy diagnostic; Emergency stop circuits comply with IEC204-1 and VDE0113 standards Digital drives and brushless servo motors Energy saving: DC bus recovers and recycles motor energy during deceleration In the event of a power failure, a stand-alone battery unit, which is being recharged continually, enables glass to going out from the section (glass reject cycle) 10 cams per servo invert Self-learning parameters plus semiautomatic operation check Real-time visual monitor of the currents absorbed by each mechanism to ensure correct operation and position during work cycle (less ware defects and less moulds maintenance)

5 SERVO TAKE-OUT Main Data Minimum Take-out In Motion Time = 280 msec. (120 degree of rotation) Take-out Pos. Accuracy= 0.18 mm on the tongs in DG 5 1/2 arm Take-out Motor type= brushless motor (very high reliability) Transmission type= ball-screw with ceramic technology (low inertia, high efficiency and reliability) Self control system to check wrong position set-up Mechanical Features High-performance mechanical drive Lower energy consumption Fewer mechanical components Interchangeable on standard I.S. machines Use of standard equipment Elimination of constant cushions and mechanical adjustments Electrical Features Control up to 12 stand-alone or integrated sections Repeatable accurate positioning Data programmed via computer and hand terminal Jog function for mechanism run from hand terminal and local section control Servo mechanism interference and anti-impact system to improve safety Servo mechanism alarm system for easy diagnostic; Emergency stop circuits comply with IEC204-1 and VDE0113 standards Digital drives and brushless servo motors Energy saving: DC bus recovers and recycles motor energy during deceleration In the event of a power failure, a stand-alone battery unit, which is being recharged continually, enables glass to going out from the section (glass reject cycle) 10 cams per servo take-out Self-learning parameters plus semiautomatic operation check Real-time visual monitor of the currents absorbed by each mechanism to ensure correct operation and position during work cycle (less ware defects and less moulds maintenance)

6 BELT DRIVEN TAKE-OUT ARM Motion without back-lash and vibrations Light-weight construction with low inertia that means less mechanical stress for the take-out mechanism Higher accurate alignment of tongs over the finish mould Very high reliability Reduced maintenance costs Main features Use of new technology synchronous belt for high torque and high temperature (up to 185 C) Housing and cover in aluminum with gasket to prevent pollution inside Belt tensioning with pulley and eccentric Belt tensioning in outside direction (positive tensioning) Supports of shaft with balls and needle roller bearing Anti-rotation safety system in case of belt broken MODULAR TAKE-OUT TONG HOLDERS The sum of single errors in the dimensional chain (take out mech. arm) can be perfectly compensated Every movable take-out head can be clamped without loosing the calibration Excellent bottle handling with blow moulds closed Excellent bottle handling on thread The same module is available to configure the tong holders in SG - DG - TG

7 BDF A.P. Pusher exact repeatability of movements improvement of production process increased productivity reduction of the defects on the container s finish reduction of environmental pollution energy savings Main Features Totally electric pusher mechanism controlled by two torque-motors Accurate ware positioning on the conveyor with the possibility to adjust the angular and parallel positions of the ware with reference to the conveyor center-line Possibility to independent speed control of each part of the motion cams Possibility of fine acceleration control on the pusher-out cam Speed and acceleration diagram display for each part of the motion cams with possibility of modification Absolute motion repeatability due to the electronic cams profile with polynomial interpolation Cam generator program to make or modify the cams profile for special or unstable conveyor ware handling; Cam simulator to check new generated cams Good unstable ware handling Very good performance on DG - TG high speed conveyors up to 70 m/min Mechanical Features Use of two coaxial torque motors Articulated pentalateral linkage for the control of the fingers position No belt transmissions and reduction-gear but only motor linkage connection Low inertia and high rigidity mechanism Very high reliability Electrical Features Integrated or stand-alone control with synchronization Use of digital drives and brushless (torque) servo motors Local controls on the machine section for each mechanism Possibility to modify the cam parameters from the machine Computer Cam generator program to make or modify the cams profile Cam simulator software to visualize the pusher motion with the bottles on the conveyor (real simulation)

8 BDF in the world companies representative offices MOSCOW MÜNCHEN SHANGHAI MEXICO CITY foshan BDF CZECH BUENOS AIRES MCR SYSTEMS BDF BDF SERVIS TDE MACNO BDF INDUSTRIES S.p.A. - Head Office and Sales Department Via dell Industria, Vicenza - Italy phone fax bdf@bdf.it studiobrand.it GTECH