127mm ~ 273mm Seamless Tube Production Plant

Size: px
Start display at page:

Download "127mm ~ 273mm Seamless Tube Production Plant"

Transcription

1 ES mm ~ 273mm Seamless Tube Production Plant Information about an exclusive method of pipe making Availability of equipment at the pipe rolling area in the manufacturing sequence of their production for the purpose of making hot-deformed, case, drilling pipes; pipelines tubes; hollow sections; rolled clutches; torque bars serving international standards and customization demands. The primary blanks for seamless steel pipe making are the blanks of Martin ingots and of cut continuous cast bars in the process of continuous casting steel. 1. Staging area Before production start-up the ingots or continuous cast bars are passing quality control and are weighted on the scales installed into the roller conveyor. Equipment: scales, roller conveyor. 2. Ingot heating This is realized in role continuous double three-zone furnaces Nr.1 and Nr. 2. Technical data of a role continuous furnace: - furnace type three-zone, continuous - feed width 4,8 m - feed length 20,75 m - feed height: - continuous zone 0,90-0,83-1,27 m - welding zone 1,27-2,60 m - soaking zone 1,30-1,90 m - furnace capacity t/h - one-time charging pcs - waste of metal up to 3% - fuel natural gas - specific fuel consumption 72,04-73,98 kg/t - furnace power 7,26-17,55 Gcal/h - furnace efficiency 39,23-40,3% Ingots canting is made by a canting machine. Equipment: role furnaces Nr. 1 and Nr.2 (two furnaces) canting machines 2 pieces 3. The ingots or continuous cast bars uniformly heated by the length and section to the needed temperature are advanced to a piercing mill for the purpose of getting cartridges and their further flattening-out on Pilger mills. Technical data of the piercing mill: - rolls diameter at over clamping mm - roll s barrel length 950 mm - number of revolutions of operating rolls 53 rev/min - feed angle (regulated) flattening-out speed (regulated) 5 0 +/ main mill drive s power 2500 kw - work holder diameter mm - cartridge diameter mm - cartridge length mm Equipment: roller conveyor to the piercing mill; kicker; a piercing mill.

2 Pilger mills purpose The obtained cartridges are advanced along the roller conveyor and are passed by the kicker to the Pilger mills. The Pilger mills are purposed for flattening-out of the cartridges into a tubing stock. The Pilger mill is made up of two operating stands. Both stands are arranged in a parallel manner to each other and share the common drive of the electric direct current motor with regulated number of revolutions and fitted with a flywheel. The stands are connected to the main clutch that couples the rotor rod with the inferior gear pinion neck of the pinion standby means of a protective spindle. In the pinion stand there are two chevron gears to the wobblers of which coupling spindles are connected by means of articulated semi-couplings, those coupling spindles pass the rotation to the operating rolls. An operating stand consists of two closed-type beds with two Pilger operating rolls placed into cushions with bushings. Every Pilger stand is equipped with a triblet-changing and triblet-cooling device of an off-the-mill triblet charging. In the process of hot Pilger rolling metal deformation is done between the rolls with variable section gage. The area of gage cross-section diminishes in the deformation process. The deformation takes place in the presence of backing-up pressure that prevents moving of the tubing stock in reverse direction and secures progressive motion in a tray about 50 meters long consisting of cast iron sections. The total length of the tubing stock obtained from the flattened-out cartridge came from the Pilger mill is exposed to end cutting and cutting to specified length sections on a disc saw and then, when hot, is exposed to stamping on stamping machines. Technical data of Pilger mill: - stand type two closed-type beds in the form of rigid rectangular frames for assembling of a couple of rolls with a variable section gage. - diameter of flattened-out tubing stocks mm - Pilger rolls diameter mm - drive power 2500 kw - number of revolutions rev/min - flywheel diameter 7000 mm - flywheel weight kg - feeding apparatus type with hydro-pneumatic braking Technical data of the feeding apparatus: - diameter of rod (piston) of the feeding apparatus (large) 550 mm (small) 360 mm - maximum stroke of the feeding apparatus rod 1500 mm - maximum stroke of the feeding apparatus 6795 mm - maximum air pressure 12 atm - feeding apparatus lubrication system circulatory - lubricant type machine oil - oil volume in the feeding apparatus tank 250 l - weight of moving parts of the feeding apparatus 2787 kg - cartridge turn to an angle degrees Equipment: Pilger mill 2 operating mills included in production and one mill reserved; feeding apparatus 2 pieces; trays made of cast iron sections 2 trays; a triblet-changing and a triblet-cooling devices 2 pieces; disc saws 2 pieces; stamping machines 2. Before reducing and calibrating the tubing stocks for clutches are delivered by the roller conveyer to the reheating continuous furnace Nr.3 where they are heated up to the needed temperature uniform by length and section.

3 Technical data of the reheating continuous furnace Nr.3: - furnace type - reheating continuous furnace with an inclined feed - feed length 7,2 m - feed width 13,58 m - fuel type natural gas - one-time furnace charging pcs - heated tubes diameter mm - heated tubes length 6-13 m - furnace capacity t/h - waste of metal up to 2% - furnace efficiency 1,99 9,95 Gcal/h Equipment: a roller conveyer, a continuous furnace. Calibrating and reducing of tubing stocks. The calibrating and the reducing mills are purposed for obtaining final geometric parameters of the heated tubes outside diameter, wall s width and length. Technical data of the calibrating and the reducing mills: - quantity of operating rolls in a stand 2-rolls - rolls diameter 550 mm - rolls width 350 mm - shaft diameter 230 mm - rolls material alloyed iron - by rolls location in the stand alternately inclined to opposite sides on-the-miter 45 to horizon and on-the-miter 90 to each other - by rolls bearing location with rolls on two bearings with regulated rolls attitude - drive system with individual drive - each stand motor power from 50 kw and more (up to 75 kw) A calibrating mill consists of five stands. It serves for calibrating tube stocks of diameter from 152 to 273 mm. A reducing mill consists of nine stands. It serves for reducing tube stocks of diameter from 127 to 152 mm. Equipment: calibrating mill one; reducing mill one. After calibration and reduction all the pipes are passed for further cooling by a roller conveyer and a kicker to a fridge (a chain conveyer). Technical data of a chain conveyer: - length 32,6 m - width 12 m - quantity of sections 2 pcs - quantity of chains in every section 6 pcs - step between chains 2,0 m - chain step 225 m - star wheel diameter 450 mm - chain velocity 0,5 1,5 m/min - electric motor type electric motor power 13 kw - star wheel number of revolutions 0,37-1,11 rev/min After cooling all the pipes are passed by a roller conveyer from the fridge to straightening machines for leveling. The pipe leveling is done through 7-rolled straightening mills 2 mills.

4 Technical data of a straightening mill: - diameter of tube for leveling mm - wall s thickness up to 50 mm - max diameter of tubes with wall s thickness 12,0 mm 240 mm - max diameter of tubes with wall s thickness 15,0 mm 220 mm - max diameter of tubes with wall s thickness 50,0 mm 160 mm - leveling velocity 0,47-1,2 m/sec - roll s length 600 mm - roll s diameter 360 mm - number of idle rolls 3 pcs - number of driving rolls 4 pcs - angle of rolls setup After leveling on straightening mills the tubes are passed by a roller conveyer to a maintenance room (an overhaul stillage) where they are identified by wall s thickness, length, outer diameter, quality of inner diameter, quality of outer surface and hot stamping, the control of tubes curvature. Then the tubes are passed to the finishing area. The quantity of the main integral units needed for production of hot-deformed, case, drilling pipes; pipelines tubes; hollow sections; rolled clutches; torque bars with the help of Pilger mills 26 pieces. The total weight of the equipment of the pipe rolling area of hot finishing of the maintenance room is about 3,5-4 thousand tons. To the above listed it is necessary to add fitment of the calibrating mill and the reducing mill with stands with rolls for each produced tube diameter; with machines of roll shop for preparing the rolls and the triblets, with special machines models KZH-2613, KZH-50, KZH-2617MF1 for welding and facing of the rolls for Pilger mills, etc. 1. Storage of billet

5 Reheating furnace No 1 Piercing mill

6 Piercing mill Piercing mill

7 Pilger rolling mill (1) Pilger rolling mill (2)

8 Reheating furnace No 2 Sizing rolling mill

9 Tube-straightening machine Cooler, chain conveyor

10 1 Storage of billets 2 Furnaces No. 1 and No.2 3 Tilter 4 Piercing mill 5 Pilger mils No. 1 and No.2 6 Cutting machines (disc saws) 7 Stamping machine 8 Furnace No.3 (reheating furnace) 9 Calibrating mill 10 Reducing mill 11 Straighteners 2 units 12 Cooler (fridge)

11

INDEX. PAGE Adjustment mechanism for radial position of block on rotating

INDEX. PAGE Adjustment mechanism for radial position of block on rotating INDEX Adjustment mechanism for radial position of block on rotating arm 520 Amplifying mechanism for precision measuring instruments--491 Angular movement, crank and link mechanisms for increasing 251,

More information

THE FUTURE NEEDS STEEL

THE FUTURE NEEDS STEEL THE FUTURE NEEDS STEEL Schmiedewerke Gröditz GmbH produces open-die forgings and seamless rolled ring products which can be supplied either rough or finish-machined on request. And in this way it pursues

More information

DEPARTMENT OF MECHANICAL ENGINEERING Subject code: ME6601 Subject Name: DESIGN OF TRANSMISSION SYSTEMS UNIT-I DESIGN OF TRANSMISSION SYSTEMS FOR FLEXIBLE ELEMENTS 1. What is the effect of centre distance

More information

High-performance Assel process

High-performance Assel process 04-631, Innovation in seamless tube rolling technology.0 * X X Р hi 6g High-performance Assel process SMS Assel mill plant production process Classic Assel mill plant Schematic production process Figure

More information

KINGS COLLEGE OF ENGINEERING DEPARTMENT OF MECHANICAL ENGINEERING

KINGS COLLEGE OF ENGINEERING DEPARTMENT OF MECHANICAL ENGINEERING KINGS COLLEGE OF ENGINEERING DEPARTMENT OF MECHANICAL ENGINEERING QUESTION BANK Sub Code/Name: ME 1352 DESIGN OF TRANSMISSION SYSTEMS Year/Sem: III / VI UNIT-I (Design of transmission systems for flexible

More information

WPP 15 T - Hydraulic table shop press with manual pump and mobile cylinder for professional use

WPP 15 T - Hydraulic table shop press with manual pump and mobile cylinder for professional use Hydraulic shop presses WPP 15 T - Hydraulic table shop press with manual pump and mobile cylinder for professional use For all repair and assembly works, e.g.: Straightening Robust frame with perforation

More information

~11. H. J. WEBER & co W. CHICAGO AVENUE CHICAGO 51, ILLINOIS COLUMBUS MACHINE TOOLS - FABRICATING EQUIPMENT

~11. H. J. WEBER & co W. CHICAGO AVENUE CHICAGO 51, ILLINOIS COLUMBUS MACHINE TOOLS - FABRICATING EQUIPMENT ~11 H. J. WEBER & co. 5722 W. CHICAGO AVENUE CHICAGO 51, ILLINOIS COLUMBUS 1-56 MACHINE TOOLS - FABRICATING EQUIPMENT c D PO ER PRESSES OPEN BACK INCLINABLE The SIXTY SERIES of C leveland Inclinable Open

More information

VW-18 OPTIONAL POWER TILT ADJUSTABLE CANTED HEAD

VW-18 OPTIONAL POWER TILT ADJUSTABLE CANTED HEAD VERTICAL BAND SAWS VW-18 Photos may show optional equipment. OPTIONAL POWER TILT Allows the operator to enter a desired angle up to 60 in either direction and have the machine automatically move the head

More information

Year of manufacture 2007 Control HEIDENHAIN itnc 530 Machine number X mm / Y mm / Z mm C - +/- 220 / B - +/- 110

Year of manufacture 2007 Control HEIDENHAIN itnc 530 Machine number X mm / Y mm / Z mm C - +/- 220 / B - +/- 110 EiMa GAMMA T LINEAR 5 axes portal machining center In excellent conditions Manufacturer Model EiMa GAMMA T LINEAR Year of manufacture 2007 Control HEIDENHAIN itnc 530 Machine number 11615 Travels X 3.700

More information

SHAFT MOUNTED HELICAL GEAR REDUCER

SHAFT MOUNTED HELICAL GEAR REDUCER Shaft Mounted Helical Gear Assembly INTRODUCTION The VIGNESSH Shaft Mounted Helical Gear Units are the result of experience in design and production, taking advantage of the most recent relevent research

More information

Automatic Pivot Style Band Saw Model S-23A

Automatic Pivot Style Band Saw Model S-23A Automatic Pivot Style Band Saw *Photo may feature machine with optional accessories Prepared By: Company: Address: Prepared For: Customer Name: Company: Address: Phone: Fax: Phone: E-mail: TECHNICAL SPECIFICATIONS

More information

ENGINE MECHANICAL <134>

ENGINE MECHANICAL <134> 11A-1 GROUP 11A ENGINE MECHANICAL CONTENTS GENERAL INFORMATION........ 11A-2.................. 11A-3 11A-2 The newly developed 1.1L 134910 engine features 3-cylinder, 12-valve, and double overhead

More information

HORIZONTAL PIVOT STYLE BAND SAWS

HORIZONTAL PIVOT STYLE BAND SAWS HORIZONTAL PIVOT STYLE BAND SAWS S-20 CAST IRON SAW HEAD Provides rigidity and less vibration when cutting. Ensures straight cuts and increases blade life! DIGITAL BAND TENSIONING DISPLAY Manual mechanical

More information

THE FUTURE NEEDS STEEL

THE FUTURE NEEDS STEEL THE FUTURE NEEDS STEEL Schmiedewerke Gröditz GmbH produces open-die forgings and seamless rolled ring products which can be supplied either rough or finish-machined on request. And in this way it pursues

More information

BOLT PLANT (Automatic)

BOLT PLANT (Automatic) BOLT PLANT (Automatic) (a) Automatic High Speed Double Stroke Cold Heading Machines (b) Automatic Bolt Head Trimming and Shank Reducing Machines (c) Automatic Thread Rolling Machines (High Speed) DOUBLE

More information

Spearhead Trident Trident 6000 Flail Mower

Spearhead Trident Trident 6000 Flail Mower Trident 6000 Flail Mower 8999094 Edition 1.0 May 2015 1 Contents Ordering Your Part s 3 S180015.130 Main Frame Assy - Mounted 4 S180015.131 Rear Linkage Assy 6 S180015.132 Trident 6000 LH Wing Arm Assy

More information

TABLE OF CONTENTS PART 7 - MACHINERY AND MACHINERY GUARDING

TABLE OF CONTENTS PART 7 - MACHINERY AND MACHINERY GUARDING TABLE OF CONTENTS PART 7 - MACHINERY AND MACHINERY GUARDING Page DEFINITIONS...7-1 SAFEGUARDS...7-1 GUARDING...7-2 PULLEYS, BELTS AND BELT-SHIFTERS...7-3 CONTROLS...7-3 FLYWHEELS...7-3 GRINDING WHEELS...7-3

More information

Detroit Speed, Inc. QUADRA Link Rear Suspension Nova P/N:

Detroit Speed, Inc. QUADRA Link Rear Suspension Nova P/N: Detroit Speed, Inc. QUADRA Link Rear Suspension 1968-1974 Nova P/N: 041704 The Detroit Speed Inc., QUADRA Link rear suspension system is a great way to upgrade from an original leaf spring rear suspension.

More information

WARE HANDLING SERVO MECHANISM SERVO INVERT SERVO TAKE-OUT BDF A.P. PUSHER

WARE HANDLING SERVO MECHANISM SERVO INVERT SERVO TAKE-OUT BDF A.P. PUSHER WARE HANDLING SERVO MECHANISM SERVO INVERT SERVO TAKE-OUT BDF A.P. PUSHER WARE HANDLING SERVO MECHANISM BDF, first in the world on the 1992, has designed and implemented in the I.S. Machines the Servo

More information

2018 Pure Stock Rules. The rules listed below are being enforced for all drivers of the Pure Stock class to abide

2018 Pure Stock Rules. The rules listed below are being enforced for all drivers of the Pure Stock class to abide 2018 Pure Stock Rules The rules listed below are being enforced for all drivers of the Pure Stock class to abide by. For questions contact the race track or technical director. Contact information is listed

More information

JET FORMING. Brakes Shears Rolls Rotary and Hand Notcher Machines Presses

JET FORMING. Brakes Shears Rolls Rotary and Hand Notcher Machines Presses Brakes....................................... 111 Shears....................................... 114 Rolls........................................ 115 Rotary and Hand Notcher Machines.............. 117

More information

MACHINE TOOLS BAND SAWS COLD SAWS DM SERIES C370 SERIES

MACHINE TOOLS BAND SAWS COLD SAWS DM SERIES C370 SERIES C370 SERIES COLD SAWS C3702SI A semiautomatic vertical column cold saw with the largest capacity in our cold saw line up, and miters 60 to left to 45 right. at 90 0 : Rectangle Hollow 7" x 3.75" Square

More information

BULLETIN 507. Mechanical Forging Presses

BULLETIN 507. Mechanical Forging Presses BULLETIN 507 Mechanical Forging Presses...-. ~ " The Erie Foundry Company designs and manufactu res quality machine tools that are used around the world. Erie presses have been built to stamp, cut, blank,

More information

METAL STAMPING & FORMING EQUIPMENT. Straight Side. Mechanical Presses tons

METAL STAMPING & FORMING EQUIPMENT. Straight Side. Mechanical Presses tons METAL STAMPING & FORMING EQUIPMENT Straight Side Mechanical Presses S2 165. 220. 330. 440. 660. 880-3300 tons S2 SERIES Straight Side Mechanical Presses Durable Reliable Versatile STRAIGHT SIDE MECHANICAL

More information

SPECIALTY PRODUCTS INDEX... A-1 MTO SPECIALTY PRODUCTS... A-2. Bronze Bushed... A-3. Ball Bearing... A-4. Ball Bearing - Non-Metallic...

SPECIALTY PRODUCTS INDEX... A-1 MTO SPECIALTY PRODUCTS... A-2. Bronze Bushed... A-3. Ball Bearing... A-4. Ball Bearing - Non-Metallic... Index SECTION A SPECIALTY SPECIALTY PRODUCTS PRODUCT PAGE INDEX................................................................................... A-1 MTO SPECIALTY PRODUCTS................................................................

More information

2019 SK Modified Open Engine Rules Supplement

2019 SK Modified Open Engine Rules Supplement 2019 SK Modified Open Engine Rules Supplement 20E- 5 GENERAL ENGINE REQUIREMENTS Engine must be OEM cast iron V8 production block, or the Dart SHP Block. Cylinder heads must be OEM or Dart 10024266, and

More information

reciprocating cam with half-cycle safety overload mechanism permits adjustable

reciprocating cam with half-cycle safety overload mechanism permits adjustable Acceleration of flying shear. device reduces initial... 104, 105 Adjusting mechanism, three-axis... 123 Arcs with inaccessible centers, plotting circular... 447-449 Assembly machine, mechanism for orienting

More information

Presentation of LORENZ GmbH Anlagentechnik.

Presentation of LORENZ GmbH Anlagentechnik. Presentation of LORENZ GmbH Anlagentechnik Company headquarters D-77948 Friesenheim Family-owned production centre Production centre Production in a building measuring 1600 m² Extensive machine park on

More information

Various duties efficiently solved EMCOMAT E-300 E-360 E-400. [ means:

Various duties efficiently solved EMCOMAT E-300 E-360 E-400. [ means: [ E[M]CONOMY] means: Various duties efficiently solved EMCOMAT E-300 E-360 E-400 Cycle-controlled lathes with high-powered cutting performance and maximum precision EMCOMAT E-300 [Headstock] - Siemens

More information

DEBURRER. for slabs, Blooms & billets

DEBURRER. for slabs, Blooms & billets DEBURRER for slabs, Blooms & billets en - Deburrer for slabs, blooms & billets After the casting process the continuous strand is cut into shorter pieces. The cutting operation is done with gas torch cutting.

More information

KMH KMH500/630/800 HORIZONTAL MACHINING CENTERS

KMH KMH500/630/800 HORIZONTAL MACHINING CENTERS KMH KMH5/63/8 HORIZONTAL MACHINING CENTERS Index Cover 1 Cover Contents 2-3 Table of Contents Structure 4-5 Design & Rigidity 6 3 Axis Transmission 7 Ballscrew Cooling System 8-9 ATC Unit Maintenance &

More information

UGE 180 N, 2 UGE 180 N UNDERFLOOR WHEEL LATHE

UGE 180 N, 2 UGE 180 N UNDERFLOOR WHEEL LATHE UGE 180 N, 2 UGE 180 N UNDERFLOOR WHEEL LATHE BASIC SPECIFICATIONS Range of wheel tread diameters: Maximum axle load: Available multi track gauge version 350 to 1,270 mm 18 10 kn PURPOSE The UGE 180 N

More information

H. J. WEBER Be CO W. CHICAGO AVENUE CHICAGO 51, ILLINOIS. COLUMBUS

H. J. WEBER Be CO W. CHICAGO AVENUE CHICAGO 51, ILLINOIS. COLUMBUS H. J. WEBER Be CO. 5722 W. CHICAGO AVENUE CHICAGO 51, ILLINOIS. COLUMBUS 1-5644 MACHINE TOOLS - FABRICATING EQUIPMENT DOUBLE CRANK POWER PRESSES INDEX POWER P STRAIGH SIDED DOUBLE CRANK SD2-60 Pa9e 3.

More information

machine tools for railways

machine tools for railways machine tools for railways RAFAMET S.A. Comprehensive solutions, advanced technologies and cost efficient productivity now much more than ever before are obvious requirements that the right equipment supplier

More information

The revamping and upgrading of Trinecke Zelezarny wire rod mill-czech Republic

The revamping and upgrading of Trinecke Zelezarny wire rod mill-czech Republic DANIELI MORGÅRDSHAMMAR The revamping and upgrading of Trinecke Zelezarny wire rod mill-czech Republic Choice of advanced equipment technology merged with Danieli s long lasting experience in upgrading

More information

OUTLINE DIMENSIONS HIGH PRESSURE PUMP HDF 40/40-8 1/6. High pressure pump HDF 40/40-8. HYDRAULIC FLOW l/min, max. 10. HYDRAULIC PRESSURE bar, max.

OUTLINE DIMENSIONS HIGH PRESSURE PUMP HDF 40/40-8 1/6. High pressure pump HDF 40/40-8. HYDRAULIC FLOW l/min, max. 10. HYDRAULIC PRESSURE bar, max. 1/6 HIGH PRESSURE PUMP HDF 40/40-8 OUTLINE DIMENSIONS HYDRAULIC FLOW l/min, max. 10 HYDRAULIC PRESSURE bar, max. 220 WATER DISCHARGE l/min, max. 40 WATER PRESSURE bar, max 40 3 4 WEIGHT kg 8 315 P T 1

More information

ARMSTRONG-BLUM MANUFACTURING CO. saoo w. Bloomingdale Avenue

ARMSTRONG-BLUM MANUFACTURING CO. saoo w. Bloomingdale Avenue ARMSTRONG-BLUM MANUFACTURING CO. saoo w. Bloomingdale Avenue Chicago Illinois 60639, USA FAST, ACCURATE, EASY OPERATION Powerful blade drive, infinitely variable speed and feed. Quickly change from automatic

More information

A quick way to get clean and calibrated tubes

A quick way to get clean and calibrated tubes A quick way to get clean and calibrated tubes GRANLUND cutting tale, type KCT and calibrating unit, type KOG Accurate length and calibrated ends The combination of GRANLUND cutting table, KCT and calibrating

More information

INDEX. 414 Agitator reversing mechanism which varies point of reversal. 250 Alternate and intermittent drive for two shafts

INDEX. 414 Agitator reversing mechanism which varies point of reversal. 250 Alternate and intermittent drive for two shafts INDEX Agitating device for pin hopper.----------------------------------------- 414 Agitator reversing mechanism which varies point of reversal. 250 Alternate and intermittent drive for two shafts.-----.----------.--..--

More information

AMCB AccuStop TM. Clutch/Brake Combination Section F

AMCB AccuStop TM. Clutch/Brake Combination Section F Clutch/Brake Combination The Airflex AMCB AccuStop clutch/brake combination consists of an air-actuated disc clutch and a spring-applied disc brake. Engineered for small-to-medium tonnage ( to 0 ton),

More information

A system of lubricant dispensing devices (oil or grease) connected by piping to a central pumping unit that is operated automatically or manually.

A system of lubricant dispensing devices (oil or grease) connected by piping to a central pumping unit that is operated automatically or manually. Air/Oil Systems: A lubrication system in which small measured quantities of oil are introduced into an air/oil mixing device which is connected to a lube line that terminates at a bearing, or other lubrication

More information

Hot Tapping Products

Hot Tapping Products Hot Tapping Products HMT Series Hot Tapping Machines The Hydratight MHT range is designed for ease of use in making 3 60 inch (76 1524mm) taps into various material pipelines and tanks with the ability

More information

Double Column Machining Center VM3018A With FANUC 0i MF LINEAR GUIDE WAY ON ALL THREE AXIS

Double Column Machining Center VM3018A With FANUC 0i MF LINEAR GUIDE WAY ON ALL THREE AXIS Offer date:2017/2/8 Quotation No.VM3018AFMF20170208A Double Column Machining Center VM3018A With FANUC 0i MF LINEAR GUIDE WAY ON ALL THREE AXIS Stock Machine for Index: A.) General Machine Description

More information

CONTENT. 1. Syllabus 2. Introduction 3. Shaft 4. Coupling. Rigid coupling. Flange coupling. Sleeve (or) muff coupling Split muff coupling

CONTENT. 1. Syllabus 2. Introduction 3. Shaft 4. Coupling. Rigid coupling. Flange coupling. Sleeve (or) muff coupling Split muff coupling UNIT II 1. Syllabus 2. Introduction 3. Shaft 4. Coupling Rigid coupling CONTENT Flange coupling Protected flange coupling Unprotected flange coupling Marine type flange coupling Sleeve (or) muff coupling

More information

2019 PURE STOCK RULES ALL CHANGES/MODIFICATIONS TO THE 2019 PURE STOCK RULES ARE IN RED.

2019 PURE STOCK RULES ALL CHANGES/MODIFICATIONS TO THE 2019 PURE STOCK RULES ARE IN RED. 2019 PURE STOCK RULES ALL CHANGES/MODIFICATIONS TO THE 2019 PURE STOCK RULES ARE IN RED. DRIVERS A. Driver must be at least 14 years of age. Must have Minor release form signed by parent or guardian on

More information

To, Purchase Manager SUB. : LIST OF USED MACHINES WITH SPECIFICATION

To, Purchase Manager SUB. : LIST OF USED MACHINES WITH SPECIFICATION Page - 1 To, Purchase Manager SUB. : LIST OF USED MACHINES WITH SPECIFICATION Dear Sir, We are pleased to enclose our offer for the following machines :- Draw Bench Semi Duty Twin HP 30 RPM 1500 (60' X

More information

Dial Test Indicators SERIES 513

Dial Test Indicators SERIES 513 Dial Test s SERIES 513 Description of Icon Icon Description With revolution counter Long contact point Jeweled bearing Double scale spacing, easy to read Compact Dustproof Anti-magnetic FEATURES Narrow

More information

TECHNICAL DATA - ENGINE 250/400/450/525 SX,MXC,EXC RACING 2005

TECHNICAL DATA - ENGINE 250/400/450/525 SX,MXC,EXC RACING 2005 10-20E TECHNICAL DATA - ENGINE 250/400/450/525 SX,MXC,EXC RACING 2005 TYPE 250 EXC 400 EXC 450 SX 450 MXC 450 EXC 525 SX 525 MXC-G 525 EXC 525 MXC DESERT Design Liquid-cooled single cylinder 4-stroke engine

More information

U-DISC 6-BOLT UNITIZED SPACER DISC COUPLING

U-DISC 6-BOLT UNITIZED SPACER DISC COUPLING U-DISC 6-BOLT UNITIZED SPACER DISC COUPLING THE U-DISC 6-BOLT UNITIZED SPACER DISC COUPLING Same Day Shipping Stocked in Two Convenient Locations Simple 3-Piece Spacer Disc Coupling Factory Pre-Assembled

More information

DXG 100 CNC Chucker with Gantry Robot

DXG 100 CNC Chucker with Gantry Robot DXG 100 CNC Chucker with Gantry Robot jyoti. co.in DXG 100 CNC Chucker with Gantry Robot OVERVIEW DXG 100 is developed by considering industry requirement of small disc - type precision components in huge

More information

turning centers Haas Automation Inc. TURNING CENTERS

turning centers Haas Automation Inc. TURNING CENTERS All New turning centers The New Generation Haas turning centers are the culmination of 15 years of continuous development, and they offer the most performance for the money the best value of any turning

More information

Detroit Speed, Inc. Front Coilover Conversion F-Body, X-Body, A-Body P/N: &

Detroit Speed, Inc. Front Coilover Conversion F-Body, X-Body, A-Body P/N: & Detroit Speed, Inc. Front Coilover Conversion 1967-69 F-Body, 1968-74 X-Body, 1968-72 A-Body P/N: 030311 & 030312 The Detroit Speed, Inc. Front Coilover Conversion Kit is a direct bolt-in kit that provides

More information

10.5 gal. Vertical Oil Lubricated Air Compressor

10.5 gal. Vertical Oil Lubricated Air Compressor 10.5 gal. Vertical Oil Lubricated Air Compressor Model No. AC1104 Tank volume: 10.5 gal. (40 L) Direct drive Oil-lubricated single cylinder pump for durability and long life triple the pump life of comparable

More information

The machine has been overhauled in 2016

The machine has been overhauled in 2016 ZENO hammer mill Type ZHM 1000/2000 x 700 Constructed in 2002 Drive power 200 kw The machine has been overhauled in 2016 Technical specifications Manufacturer ZENO Zerkleinerungsmaschinenbau Norken GmbH,

More information

Design and Vibrational Analysis of Flexible Coupling (Pin-type)

Design and Vibrational Analysis of Flexible Coupling (Pin-type) Design and Vibrational Analysis of Flexible Coupling (Pin-type) 1 S.BASKARAN, ARUN.S 1 Assistant professor Department of Mechanical Engineering, KSR Institute for Engineering and Technology, Tiruchengode,

More information

Insulating Glass machines

Insulating Glass machines Insulating Glass machines Vertical Insulating Glass Production Line LBZ2500PY Features and specialties: PLC control system with whole process, touch-sensitive screen and man-machine interface. Realize

More information

GÝROL FLUID DRIVES GÝROL FLUID DRIVES SAVE ENERGY HOW GÝROL FLUID DRIVES WORK

GÝROL FLUID DRIVES GÝROL FLUID DRIVES SAVE ENERGY HOW GÝROL FLUID DRIVES WORK GÝROL FLUID DRIVES Gýrol Fluid Drives are used to control speed and to absorb shock and torsional vibration. These extremely robust variable speed hydraulic drives provide a reliable, low maintenance,

More information

MTAB. MACHINING CENTERS

MTAB.   MACHINING CENTERS MTAB www.mtabcnc.com MACHINING CENTERS OVERVIEW MTAB's Vertical Machining Center is designed to flex with the customers' manufacturing demands and requirements. The machines are high performance systems,

More information

Manual. Air-hydraulic Drilling Unit Series BE 33. Read this manual before installation and commissioning of the product. Keep for future reference.

Manual. Air-hydraulic Drilling Unit Series BE 33. Read this manual before installation and commissioning of the product. Keep for future reference. EN Manual Air-hydraulic Drilling Unit Series BE 33 Read this manual before installation and commissioning of the product. Keep for future reference. MAN045 - Manual BE 33, EN, Rev. 02.doc Table of content:

More information

SURFACE GRINDERS. A Line of Precision Low-cost, High Performance Surface Grinders

SURFACE GRINDERS. A Line of Precision Low-cost, High Performance Surface Grinders SURFACE GRINDERS PRODUCT CATALOG www.clausing-industrial.com 800.323.0972 SURFACE GRINDERS A Line of Precision Low-cost, High Performance Surface Grinders Precision Manual Surface Grinders Precision Hydraulic

More information

Taladro automático por coordenadas Automatic coordinate drilling machine TECHNICAL CHARACTERISTICS

Taladro automático por coordenadas Automatic coordinate drilling machine TECHNICAL CHARACTERISTICS RAPID DRILL TRD SERIES FIXED BED-TYPE Equipment: automatic X- Y and Z -axis, driven by servo-motors (programmable) Spindle turning driven also by asynchrony motor of 8,9 kw or servomotor 4,4 kw. Column

More information

METAL STAMPING & FORMING EQUIPMENT. WFSeries. Warm / Hot Forging Presses ton

METAL STAMPING & FORMING EQUIPMENT. WFSeries. Warm / Hot Forging Presses ton METAL STAMPING & FORMING EQUIPMENT WFSeries Warm / Hot Forging Presses 400. 600. 800. 1000. 1600 ton WF1 and WF2 Series Warm / Hot Forging Presses Stamtec WF1 and WF2 Series Warm / Hot Forging Presses,

More information

w w w. j y o t i. c o. i n Performance Series Vertical Machining Center

w w w. j y o t i. c o. i n Performance Series Vertical Machining Center w w w. j y o t i. c o. i n Performance Series Vertical Machining Center Performance Series Vertical Machining Center Overview To match the demand of greater accuracy and total reliability at higher speeds

More information

Gearbox standard series Your industrial Gearboxes. Standard Industrial NH/NHK

Gearbox standard series Your industrial Gearboxes.  Standard Industrial NH/NHK www.gamesagearbox.com Standard Industrial 1 Contents Gear Design and Construction 3 Service Factors 5 Example of Selection 7 Spur Gearboxes NH I 8 NH II, NHS II, NHZ I2 NH III, NHS III, NHZ II7 NH IV,

More information

APPLICATIONS APPLICATIONS

APPLICATIONS APPLICATIONS APPLICATIONS APPLICATIONS TWO STROKE ENGINE FOR PORTABLE SAW The high speeds attained by these engines subject the connecting rod bearings to extremely arduous working conditions, made worse by doubtful

More information

COOPERATIVE PATENT CLASSIFICATION

COOPERATIVE PATENT CLASSIFICATION CPC F COOPERATIVE PATENT CLASSIFICATION MECHANICAL ENGINEERING; LIGHTING; HEATING; WEAPONS; BLASTING (NOTE omitted) ENGINES OR PUMPS F01 MACHINES OR ENGINES IN GENERAL (combustion engines F02; machines

More information

w w w. m a r v e l s a w s. c o m

w w w. m a r v e l s a w s. c o m Quality Machines by Vertical Band Saws Series 8 Mark III Miter cuts up to 60 with optional power column tilt. Column adjustable from 90 to 3 canted. Capacity: 18 X 22 (457mm x 560mm) at 45 18 x 14.5 R,

More information

MultiCam 3000 Series CNC Router Feature and Specification Guide. Versatile, Feature-Rich Production Routing! The MultiCam. Ideal for Cutting: Wood

MultiCam 3000 Series CNC Router Feature and Specification Guide. Versatile, Feature-Rich Production Routing! The MultiCam. Ideal for Cutting: Wood MultiCam 3000 Series CNC Router Feature and Specification Guide Versatile, Feature-Rich Production Routing! The MultiCam 3000 Series CNC Routers are loaded with standard features normally associated with

More information

FLOOR TYPE HORIZONTAL MILLING MACHINES

FLOOR TYPE HORIZONTAL MILLING MACHINES FLOOR TYPE HORIZONTAL MILLING MACHINES TARGET AND APPLICATION 2 AEROSPACE DIE & MOLD EARTH MOVING ENERGY OIL & GAS GENERAL MACHINING PAMA Speedmill is the ideal solution for all application requiring high

More information

new SPREAD SEEDER COMBINED MARTE + MINIGO

new SPREAD SEEDER COMBINED MARTE + MINIGO SPREAD SEEDER COMBINED MARTE + MINIGO HP 40-80 KW 29-59 TECHNICAL SPECIFICATIONS POWER HARROW MINIGO maximum horse power: 80 HP (59 KW) rotor speed: 319 rpm (for 540 rpm PTO) 3 point hitch cat.1 cage roller

More information

Copyright EXTRON All rights reserved E-EH-EN EXTRONCNC.com

Copyright EXTRON All rights reserved E-EH-EN EXTRONCNC.com YIH CHUAN MACHINERY INDUSTRY CO., LTD HEADQUARTERS 40755 No.8, 9 Rd., Taichung Industrial Park, Taichung, Taiwan T e l : +886-4-2359-3351 Fa x : +886-4-2359-0012 E-mail : extron@extroncnc.com th YIH CHUAN

More information

Current Price List Jan 2013

Current Price List Jan 2013 Crankshafts Current Price List Jan 2013 Pearson Flywheel Assembly standard ⅞ T/S Shaft 1⅛ D/S Shaft, Carrillo Con-Rod balanced to your Piston. 88 Stroke for Gold Star Crankcases. Direct replacement. 800.00

More information

Detroit Speed, Inc. QUADRA Link Rear Suspension Chevy II P/N:

Detroit Speed, Inc. QUADRA Link Rear Suspension Chevy II P/N: Detroit Speed, Inc. QUADRA Link Rear Suspension 1962-1967 Chevy II P/N: 041707 Detroit Speed, Inc. QUADRAlink is a great way to upgrade from original leaf spring suspension. Unlike our competitors, Detroit

More information

SECTION SWING CHECK VALVES

SECTION SWING CHECK VALVES PART 1 GENERAL 1.1 DESCRIPTION This section includes materials, testing, and installation of swing check valves as shown in the Drawings and specified herein, in accordance with the requirements of the

More information

CHENDU COLLEGE OF ENGINEERING & TECHNOLOGY DEPARTMENT OF MECHANICAL ENGINEERING QUESTION BANK

CHENDU COLLEGE OF ENGINEERING & TECHNOLOGY DEPARTMENT OF MECHANICAL ENGINEERING QUESTION BANK CHENDU COLLEGE OF ENGINEERING & TECHNOLOGY DEPARTMENT OF MECHANICAL ENGINEERING QUESTION BANK Sub Code: ME 2342 DESIGN OF TRANSMISSION SYSTEM UNIT - I 1. How the bevel gears are classified? Explain with

More information

Screw Compactor without feeding device

Screw Compactor without feeding device Screw Compactor without feeding device foils, residual waste, polystyrene, PET bottles (pre-crushed) 1500 x 1420 x 1300 mm 1400 x 1200 mm 11 kw / 15 kw 50 A / 63 A 22,5 A / 30 A foils 4,5 6,0 t residual

More information

FAMUP MC and MCP. Vertical CNC machining centers with and without pallet changer.

FAMUP MC and MCP. Vertical CNC machining centers with and without pallet changer. EMCO FAMUP CNC machining centers Vertical milling centers FAMUP MC-Line/MCX-Line With integrated pallet changer FAMUP MCP-Line Vertical milling machines FAMUP MMV-Line EMCO, the industrial systems supplier

More information

Detroit Speed, Inc. QUADRA Link Rear Suspension Camaro/Firebird P/N:

Detroit Speed, Inc. QUADRA Link Rear Suspension Camaro/Firebird P/N: Detroit Speed, Inc. QUADRA Link Rear Suspension 1967-1969 Camaro/Firebird P/N: 041703 The Detroit Speed Inc., QUADRA Link rear suspension system is a great way to upgrade from an original leaf spring rear

More information

Metal Stamping & Forming Equipment

Metal Stamping & Forming Equipment COMPANY and PRODUCT OVERVIEW Metal Stamping & Forming Equipment Mechanical / Hydraulic / Servo Presses and Peripheral Equipment High performance metal stamping & forming production equipment OUR COMPANY

More information

CONVENTIONAL ENGINE CONSTRUCTION

CONVENTIONAL ENGINE CONSTRUCTION CONVENTIONAL ENGINE CONSTRUCTION CYLINDER BLOCKS, HEADS, AND CRANKCASES The cylinder, or the engine block, is the basic foundation of virtually all liquid-cooled engines. The block is a solid casting made

More information

Multi-Purpose Milling Machine

Multi-Purpose Milling Machine Multi-Purpose Milling Machine MF most widely used milling machine type world-wide! MF 1 speed change through v-belt change-over Multi-Purpose Milling Machine for workshops, single part production, design,

More information

Sheet Metal Forming Presses

Sheet Metal Forming Presses Sheet Metal Forming Presses October 15th, 2014 Hyunok Kim, EWI Forming Center Taylan Altan, OSU - Center for Precision Forming (CPF) 1 Outline Introduction Classification of presses Mechanical press Hydraulic

More information

Ductile Iron. Fittings and Accessories for pressure pipelines. 1 st issue

Ductile Iron. Fittings and Accessories for pressure pipelines. 1 st issue Ductile Iron Fittings and Accessories for pressure pipelines 1 st issue INTRODUCTION Tawakol Metal Industries is Egypt's main manufacturer of Grey and Ductile Cast Iron products since 1975. TMI's reputation

More information

BASANT MECHANICAL WORKS (REGD.) MANUFACTURERS & EXPORTERS OF HIGH CLASS POWER PRESSES AND KNUCKLE JOINT PRESSES.

BASANT MECHANICAL WORKS (REGD.) MANUFACTURERS & EXPORTERS OF HIGH CLASS POWER PRESSES AND KNUCKLE JOINT PRESSES. 7-721, Basant Road, Industrial Area-B, Ludhiana - 13 (INDIA) 91-97802-00007, 9315-11111 info@basantgroup.com www.basantgroup.com BASANT MECHANICAL WORKS (REGD.) MANUFACTURERS & EXPORTERS OF HIGH CLASS

More information

4242SR SPECIFICATION IMPACT CRUSHER APPLICATIONS. Above photograph features a 4242SR fitted with the optional side conveyor and magnet

4242SR SPECIFICATION IMPACT CRUSHER APPLICATIONS. Above photograph features a 4242SR fitted with the optional side conveyor and magnet Above photograph features a 4242SR fitted with the optional side conveyor and magnet IMPACT CRUSHER Crusher type: Feed opening: Rotor Rotor Diameter: Crusher frame: Rotor: Blowbars: Impact aprons: Engine

More information

F-800 and F-1000 MUD PUMP Specification and Performance

F-800 and F-1000 MUD PUMP Specification and Performance This product conform to API Spec 7K, F-800 and F-1000 MUD PUMP Specification and Performance Distributed by 1. Technical Specification and performance Parameter 1.1 F-800 and F-1000 Mud Pumps Specification

More information

CTV 160 / 250 / 315 CTV 250 DF. VERTICAL PRODUCTION TURNING CTV series DMGMORI.COM

CTV 160 / 250 / 315 CTV 250 DF. VERTICAL PRODUCTION TURNING CTV series DMGMORI.COM CTV 160 / 250 / 315 CTV 250 DF VERTICAL PRODUCTION TURNING CTV series DMGMORI.COM Applications and Parts Machine and Technology Control Technology Technical Data CTV SERIES CTV One concept with four versions

More information

Stopping Accuracy of Brushless

Stopping Accuracy of Brushless Stopping Accuracy of Brushless Features of the High Rigidity Type DGII Series Hollow Rotary Actuator The DGII Series hollow rotary actuator was developed for positioning applications such as rotating a

More information

Specifications For MEYER UTG GEAR STAINLESS STEEL. General: Comply Exception

Specifications For MEYER UTG GEAR STAINLESS STEEL. General: Comply Exception MEYER UTG GEAR STAINLESS STEEL General: This under tailgate shall be of the bottom opening design. The entire unit shall rigidly mount to the side of the dump box with single pin quick detachable hardware.

More information

DEBURRER FOR SLABS, BLOOMS & BILLETS

DEBURRER FOR SLABS, BLOOMS & BILLETS DEBURRER FOR SLABS, BLOOMS & BILLETS en DEBURRER FOR SLABS, BLOOMS & BILLETS After the casting process the continuous strand is cut into shorter pieces. The cutting operation is done with gas torch cutting.

More information

Cutting, Drilling and Beveling

Cutting, Drilling and Beveling Pipe Hole Cutter JK150 The Hongli Model JK150 pipe hole cutter is designed to cut holes up to 152mm into steel pipe. The multiple hole sizes allow the use of Mechanical fittings for branching unpressurized

More information

AccuMax 3060 Multi-Point Detailed Specifications

AccuMax 3060 Multi-Point Detailed Specifications AccuMax 3060 Multi-Point Detailed Specifications A FoamPro AccuMax, part number S111-3060A electronic/hydraulic foam proportioning system shall be provided. The system shall be demand based, fully automatic

More information

SERETOULIS V. - PROKOPIDIS S. G.P.

SERETOULIS V. - PROKOPIDIS S. G.P. Screw Conveyors SERETOULIS V. - PROKOPIDIS S. G.P. DEVELOPMENT & MANUFACTURING COMPANY OF ELECTROMECHANICAL INSTALLATIONS SP - SC Screw Conveyors Screw Conveyors know - how Presentation Screw conveyor

More information

PNEUMATIC ACTUATOR FIG. PD - PE

PNEUMATIC ACTUATOR FIG. PD - PE FIG. PD - PE New design Single acting type PE Available from size12 up to 350 Double acting type PD Available from size12 up to 350 Old design Single acting type PE Available from size 600 up to 000 Soon

More information

Shaft Mounted Speed Reducer. Technical Catalogue

Shaft Mounted Speed Reducer. Technical Catalogue Shaft Mounted Speed Reducer Technical Catalogue Where others fit, We perform Contents The Challenge SMSR stands tall amongst the crowd. Packed full of attention to detail, the Challenge SMSR delivers performance

More information

CTX 2-axis Universal Turning Machines CTX 4-axis Production Turning Machines. CTX alpha / beta / gamma

CTX 2-axis Universal Turning Machines CTX 4-axis Production Turning Machines. CTX alpha / beta / gamma www.dmgmoriseiki.com Cooperation sustains innovation CTX 2-axis Universal Turning Machines CTX 4-axis Production Turning Machines CTX alpha / beta / gamma 02 05 Applications and Highlights 06 29 Machine

More information

BUTTERFLY VALVE WITH WELDED ENDS INSTALLATION AND MAINTENANCE MANUAL

BUTTERFLY VALVE WITH WELDED ENDS INSTALLATION AND MAINTENANCE MANUAL BUTTERFLY VALVE 31300 SERIES INSTRUCTIONS FOR INSTALLATION, USE AND MAINTENANCE 1. Overview Read these instructions carefully before starting the valve installation and start-up work. Safe keep the instructions

More information

QUESTION BANK Chapter:-6 Design of IC Engine Components

QUESTION BANK Chapter:-6 Design of IC Engine Components QUESTION BANK Chapter:-6 Design of IC Engine Components Que:-1 Design a cast iron piston for a single acting four stroke diesel engine for following data: Cylinder bore = 100 mm, stroke = 125 mm, Pmax

More information

TM T.O. 38G

TM T.O. 38G T.O. 38G1-48-12-2-1 TECHNICAL MANUAL VOLUME 2 OF 2 PART 1 OF 2 MAINTENANCE DIRECT SUPPORT AND GENERAL SUPPORT LEVEL ENGINE ASSEMBLY, DIESEL (MULTIFUEL): NATURALLY ASPIRATED OR TURBOCHARGED, FUEL-INJECTED,

More information

Technical News Bulletin

Technical News Bulletin Technical News Bulletin April 1995 3000 Series Process Control 1. Introduction Quick Change Plunger Mechanisms Series 3000 are now provided with an additional operating enhancement. To permit optimization

More information