reliable economical general characteristics

Transcription

1 general characteristics reliable economical inserts in light technopolymer tinned precision contacts enclosures in die-cast aluminum alloy vertical safety closing levers in zinc-plated steel 1

2 JNE inserts for multipole connectors polarity: 6, 10, 16, 2 + m rated current: 16 rated voltage: 500V EN 6198 ( ): 500V/6kV/3-00V/690V/6kV/2 screw terminal for conductors, section mm 2 - WG 20 1, with conductor protection plate different sized steel screws contact surface: tinned UL V0 approved self-extinguishing thermoplastic material JNE 06 - JNE 06 polarity (contact side) 27 JNE 10 - JNE 10 polarity (contact side) JNE 16 - JNE 16 polarity (contact side) JNE 2 - JNE 2 polarity (contact side)

3 JNE inserts for multipole connectors drawing ILE description package part No. JNE inserts V/6kV/3 female inserts JNE poles + m for enclosure size.27 10/100 JNE poles + m for enclosure size /80 JNE poles + m for enclosure size /80 JNE 2 2 poles + m for enclosure size /80 male inserts JNE poles + m for enclosure size.27 10/100 JNE poles + m for enclosure size /80 JNE poles + m for enclosure size /80 JNE 2 2 poles + m for enclosure size /80 Enclosure identification atching connector inserts with the correct enclosures can be complicated. To simplify we have used the definition of size in addition to the product s normal identification code. rom the figure to the left and the table below, this new variable refers to the fixing distance between screw centres which, is the same for inserts and enclosures, and clear. ll the pages illustrating inserts and enclosures bear the relevant identification references. The table below sets out all the enclosure sizes and the dimension of the insert fixing slots. enclosure slot for inserts with size fixing distance identification x - y.27 x 27 mm x 27 mm x 27 mm x 27 mm 3

4 JV enclosures in aluminum alloy painted with grey RL 700 enclosures JVI / JVP with two levers in zinc-plated steel IP65 degree of protection in accordance with EN for inserts size 57.27, 77.27, JVI panel cut-out for bulkhead housings in mm Ø.5 D type D JVI JVI JVI JVP D 58 Pg/ Pg/ Ø 5.5 E type D E JVP JVP JVP

5 JV bulkhead mounting housings with levers may be combined with: hoods without gasket, with pegs for two levers closing covers with pegs for two levers D T DD QE N-NE T SE P X IXO JNE TS E TSE E package standard version (10) SE (16) JVI 10 size /2 3* 10 5/0 JVI 16 size * 16 5/0 JVI 2 size /8 6* 2 5/0 Pg threading - wall-mounting housings with levers may be combined with: hoods without gasket, with pegs for two levers closing covers with pegs for two levers D DD QE N-NE SE P X IXO JNE normal E E package standard version SE JVP 10 size Pg /2 3* 10 5/20 JVP 16 size Pg * 16 5/20 JVP 2 size Pg /8 6* 2 5/20 - enclosures with metric threading upon request - high enclosures upon request - characteristics of other inserts, not belonging to the Jei series, in the N catalogue 5

6 JH enclosures in aluminum alloy painted with grey RL 700 JHO / JHV enclosures with pegs for 2-lever enclosures IP65 degree of protection in accordance with EN for inserts size 57.27, 77.27, JHO Pg/ 3 type JHO JHO JHO JHV Pg/ 3 type JHV JHV JHV

7 JH Pg threading - side entry hoods - with pegs may be combined with: bulkhead or wall-mounting housings with two levers and gasket hoods with two levers and gasket closing covers with two levers and gasket D DD QE N-NE SE P X IXO JNE normal E E package standard version SE JHO 10 size Pg /2 3* JHO 16 size Pg * JHO 2 size Pg /8 6* enclosures with metric threading upon request - high enclosures upon request - characteristics of other inserts, not belonging to the Jei series, in the N catalogue Pg threading - top entry hoods - with pegs may be combined with: bulkhead or wall-mounting housings with two levers and gasket hoods with two levers and gasket closing covers with two levers and gasket D DD QE N-NE SE P X IXO JNE normal E E package standard version SE JHV 10 size Pg /2 3* JHV 16 size Pg * JHV 2 size Pg /8 6* enclosures with metric threading upon request - high enclosures upon request - characteristics of other inserts, not belonging to the Jei series, in the N catalogue 7

8 JV enclosures in aluminum alloy painted with grey RL 700 enclosures JVI L / JVP L with one lever in zinc-plated steel IP65 degree of protection in accordance with EN for inserts size.27, 57.27, 77.27, JVI L panel cut-out for bulkhead housings in mm Ø.5 D type D JVI 06 L JVI 10 L JVI 16 L JVI 2 L JVP L D Pg/ Pg/ Ø 5.5 E type D E JVP 06 L JVP 10 L JVP 16 L JVP 2 L

9 JV bulkhead mounting housings with single lever may be combined with: hoods with pegs for one lever closing covers with pegs for one lever D T DD QE N-NE T SE P X IXO JNE TS E TSE E package standard version (10) SE (16) JVI 06 L size * 6 5/0 JVI 10 L size /2 3* 10 5/20 JVI 16 L size * 16 5/20 JVI 2 L size /8 6* 2 5/20 Pg threading - wall-mounting housings with single lever may be combined with: hoods with pegs for one lever closing covers with pegs for one lever D DD QE N-NE SE P X IXO JNE E E package standard version SE JVP 06 L size.27 - Pg * 6 5/20 JVP 10 L size Pg /2 3* 10 5/10 JVP 16 L size Pg * 16 5/10 JVP 2 L size Pg /8 6* 2 5/10 - enclosures with metric threading upon request - high enclosures upon request - characteristics of other inserts, not belonging to the Jei series, in the N catalogue 9

10 JV enclosures in aluminum alloy painted with grey RL 700 JVI LP / JVP LP enclosures with one lever in zinc-plated steel and a cover in self-extinguishing thermoplastic material IP65 degree of protection in accordance with EN for inserts size.27, 57.27, 77.27, JVI LP panel cut-out for bulkhead housings in mm Ø.5 D type D JVI 06 LP JVI 10 LP JVI 16 LP JVI 2 LP JVP LP D Pg/ Pg/ Ø 5.5 E type D E JVP 06 LP JVP 10 LP JVP 16 LP JVP 2 LP

11 JV bulkhead mounting housings with lever and thermoplastic cover may be combined with: hoods with pegs for one lever D T DD QE N-NE T SE P X IXO JNE TS E TSE E package standard version (10) SE (16) JVI 06 LP size * 6 5/20 JVI 10 LP size /2 3* 10 5/20 JVI 16 LP size * 16 5/20 JVI 2 LP size /8 6* 2 5/20 Pg threading - wall-mounting housings with lever and thermoplastic cover may be combined with: hoods with pegs for one lever D DD QE N-NE SE P X IXO JNE E E package standard version SE JVP 06 LP size.27 - Pg * 6 5/10 JVP 10 LP size Pg /2 3* 10 5/10 JVP 16 LP size Pg * 16 5/10 JVP 2 LP size Pg /8 6* 2 5/10 - enclosures with metric threading upon request - high enclosures upon request - characteristics of other inserts, not belonging to the Jei series, in the N catalogue 11

12 JH enclosures in aluminum alloy painted with grey RL 700 JHO L / JHV L enclosures with 2 pegs for 1-lever enclosures IP65 degree of protection in accordance with EN for inserts size.27, 57.27, JHO L Pg/ 3 type JHO 06 L JHO 10 L JHO 16 L JHO 2 L JHV L Pg/ 3 type JHV 06 L JHV 10 L JHV 16 L JHV 2 L

13 JH Pg threading - side entry hoods - with pegs may be combined with: bulkhead or wall-mounting housings with lever hoods with lever closing covers with lever D DD QE N-NE SE P X IXO JNE normal E E package standard version SE JHO 06 L16 size.27 - Pg * JHO 10 L size Pg /2 3* JHO 16 L size Pg * JHO 2 L size Pg /8 6* enclosures with metric threading upon request - high enclosures upon request - characteristics of other inserts, not belonging to the Jei series, in the N catalogue Pg threading - top entry hoods - with pegs may be combined with: bulkhead or wall-mounting housings with lever hoods with lever closing covers with lever D DD QE N-NE SE P X IXO JNE normal E E package standard version SE JHV 06 L16 size.27 - Pg * JHV 10 L size Pg /2 3* JHV 16 L size Pg * JHV 2 L size Pg /8 6* enclosures with metric threading upon request - high enclosures upon request - characteristics of other inserts, not belonging to the Jei series, in the N catalogue 13

14 R accessories for multipole connectors drawing ILE description package part No. code pins and guides single pin - in steel - for 6 variants R 20 D for connector inserts 50 double pin - in steel - for 16 variants R D male - for connector inserts 50 R D female - for connector inserts 50 selection using single code pins selection using double code pins application with single insert application with single insert application with double inserts application with double inserts code pin (R 20 D) + normal fixing screw = male insert = female insert female code pin (R D) male code pin (R D) + normal fixing screw = male insert = female insert 1