SPLIT CASE PUMPS REPLACEMENT PARTS GUIDE
|
|
- Ambrose Sullivan
- 6 years ago
- Views:
Transcription
1 PACO Split Case Kits are arranged so that you can replace virtually any component with minimum of effort. Here are some guidelines and suggestions: GENERAL NOTES: The pump nameplate contains all data required in the selection and ordering of the proper replacement parts kit. The pump model and serial number should be referenced whenever any replacement parts kit is ordered, while the pump conditions (GPM/TDH) and impeller trim are required data for the ordering of replacement impellers. To replace a mechanical seal. Select the correct Seal Kit, (which contains a complete Gasket Kit and a Bearing Kit) which will maximize seal life and eliminate future down time. Shaft sleeve inspection is suggested, and replacement made as indicated. To replace the packing. A Packing Kit is needed. (Again, Bearing and Gasket Kits are included.) Shaft sleeve inspection is recommended. If packing glands are damaged, they may be replaced by ordering the proper Packing Gland Kit. To replace the shaft sleeves. You will need a Shaft Sleeve Kit. A Seal or Packing Kit will provide all other normally needed parts. To replace bearings. A Bearing Kit is required and a Gasket Kit is recommended. Bearing Kits and Gasket Kits are included in Seal/Packing Kits. To replace case wear rings. A Case Wear Ring Kit is required. A Seal/Packing Kit will provide all other normally replaced components. To replace impeller. An Impeller Kit is required; a Case Wear Ring Kit is highly recommended, and a Seal or Packing Kit will provide all other normally replaced components. To replace the shaft. The correct shaft should be selected. Shaft replacement is most often accompanied by replacement of the seal/packing and sleeves. To inspect the pump internals. Since gaskets are often damaged, a Gasket Kit is recommended. To replace lost/damaged hardware. Hardware Kits are available, for 175 PSI units. (For 250 PSI refer to factory). To overhaul the pump. (Replace Rotating Assembly.) You will need an Impeller Kit, a Wear Ring Kit, a Shaft Sleeve Kit, a Seal/Packing Kit and a shaft. NOTE: Seal/Packing Kits are always recommended as spare parts. Page 1 of 6
2 Model Packing Constr. Mechanical Seal Kit Packing Or Seal Code To 200 PSI Working Pressure Over 200 PSI Working Pressure Kit Size Ceramic Ni-Resist Ni-Resist Tung. Car 212 PSI 250 PSI 250 PSI 350 PSI 232 PSI 250 PSI 500 PSI (ID of Seal) Seat/Buna Seat/Buna Seat/Viton Seat/Viton MAX MAX MAX MAX MAX MAX MAX Elastomers Elastomers Elastomers Elastomers Ceramic Ni-Resist Ni-Resist Tung. Car. Sic-Sic Balanced Balanced BF1C1 BF171 XF171 XF1D1 Seat/Buna Seat/Buna Seat/Viton Seat/Viton Seat/Viton Sic Seat Buna Code: Code: Code: Code: Elastomers Elastomers Elastomers Elastomers Elastomers Viton El. Ceramic 1XXXXX 7XXXXX 6XXXXX 2XXXXX BF2C1 BF271 XF271 XF2D1 XP1O81 XP1O81 BF2C1 Code: Code: Code: Code: Code: Code: Code: AXXXXX DXXXXX BXXXXX CXXXXX 9XXXXX GXXXXX 8XXXXX / /6 1 X X X X X / X XE K K K / X / X C/D 1.81 XF K K / X / X C/D 1 XG K K / X / X / X / X / X / X K / X K / X / X / X / X / X / X / / / X X X X X X / X / X / X K K / X / X K X K K K K K K K / X RTF / X K K K K K K K X K K K K K / XK K1978 AMC AMC / XK / X RTF / X K / X K / X K /2 3 X /4 3 X /4 4 XV /2 4 XV RTF RTF RTF - - RTF /4 4 XV RTF RTF RTF - - RTF /2 3 X AMC AMC AMC AMC - - AMC AMC / XK RTF RTF / XK K0288-B K0288-C - - K RTF Page 2 of 6
3 Model Constr Gasket Gasket Hardware Hardware Hardware Packing Bearing Sleeve Kits Code Kit Kit Kit Kit Kit Gland Kit Impeller Kit* For Use With X006 X008 steel steel stainless Kit Balanced Seal grade 5 grade 8 steel H Hardened 303 Bronze Bronze Iron Stainless Stainless Bronze Stainless Stainless Stainless 416 S.S. Bronze Stainless B21 B22 Steel Steel H304 H /2 X (X3) X /6 X X /8 X K0502-C X K0502-C XE K0406-C RTF /6 X K0503-C /8 X C/D XF K0428-C AMC AMC AMC /2 X K0504-C /2 X K0504-C C/D XG K K K0429-C K K /8 X /8 X /6 X /8 X /0 X /6 X /8 X /8 X /0 X K0510-C /2 X K0511-C /4 X /2 X /4 X /2 X K0514-C X K0515-C AMC AMC /6 X X K0517-C AMC AMC /8 X X K0517-C /4 X /6 X6 AMC - AMC K0296-B - K0296-C AMC AMC /4 X /6 X /2 X X6 AMC - AMC K0521-B - K0521-C AMC AMC /4 X K0522-C /6 X K0523-C X k0524-c /4 XK AMC - - AMC AMC AMC /6 XK /2 X /4 X K0525-C /8 X K0525-C /0 X K0526-C /2 X K0527-C /4 X K0537-C K K /4 XV RTF /2 XV K0298-B - K0298-C K K K /4 XV K0281-B - K0281-C RTF K K /2 X7 AMC - AMC - - AMC AMC AMC - AMC - - AMC AMC - - AMC AMC AMC /6 XK K K /2 XK K0373-C K K /6 XK /8 XV Page 3 of 6
4 Shafts Model Constr Wear Wear CW CCW Code Ring Ring Seal Packing Seal Packing Kit B18* Kit N* Steel Stainless Steel Stainless Steel Stainless Steel Stainless /2 X X /6 X X /8 X X XE /6 X /8 X C/D XF /2 X /2 X C/D XG /8 X /8 X /6 X /8 X /0 X /6 X /8 X /8 X /0 X /2 X /4 X /2 X /4 X /2 X X /6 X X /8 X X /4 X /6 X /4 X /6 X /2 X X F H F H F H F H /4 X /6 X X /4 XK /6 XK /2 X /4 X /8 X /0 X /2 X /4 X /4 XV /2 XV AMC /4 XV RTF /2 X7 AMC AMC AMC F AMC F AMC /6 XK /2 XK /6 XK Page 4 of 6
5 Model Constr KPV Lower Code Sleeve Kits X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X XE XE X X X X X X X X Page 5 of 6
6 EXPLANATION OF PUMP CODING (REFER TO PUMP NAMEPLATE) XX - XXXXX - XXXXXX PRODUCT MODEL CONSTRUCTION CODE NUMBER CODE While PACO Split Case Pumps are designed and built to provide maximum life while requiring minimum attention and service, replacement parts may at times be required. VIRTUALLY ALL REQUIRED PARTS ARE AVAILABLE IN KIT FORM. These kits (easily selected from the charts on the preceeding pages) have been designed to insure that any part needed when replacing any split case component is furnished when you need it. KIT COMPONENTS SEAL KIT: PACKING KIT: GASKET KIT: BEARING KIT: Mechanical Seals Packing Set Case Gasket Bearings Gasket Kit Lantern Rings Seal HSG. Gaskets Support Washers Bearing Kit Retaining Rings Brg. Cap Gaskets Retaining Rings Gasket Kit Slingers Bearing Kit PACKING GLAND KIT: HARDWARE KIT: WEAR RING KIT: IMPELLER KIT: Packing Glands Capscrews Wear Rings Bronze or Iron Impeller Studs Roll Pins Roll Pins Impeller Key Nuts Nuts Snap Rings Coupling Key SLEEVE KIT: SHAFTS: SLEEVE BEARING KIT: (non-kitted) Inboard Sleeve Shaft LH sleeve Outboard Sleeve Steel or Stainless Gasket Kit Lower Sleeve Sleeve Gaskets Packed or Seal Bearing Slinger Locking Collars Bearing Housing (where applicable) Mechanical Seal NOTE: Kits may not contain all parts listed. They are individually selected for each pump and its construction. Page 6 of 6
SPLIT-COUPLED INLINE PUMP WITH INTEGRATED VARIABLE FREQUENCY DRIVE REPLACEMENT PARTS GUIDE VLSE
SPLIT-COUPLED INLINE PUMP WITH INTEGRATED VARIABLE FREQUENCY DRIVE REPLACEMENT PARTS GUIDE VLSE This guide is valid for all Grundfos CBS Inc. products beginning with product code 28 only. While Paco In-Line
More informationA3b.2 October, 2013 Supercedes June, 2013 INLINE CENTRIFUGAL PUMPS REPLACEMENT PARTS GUIDE PACO TYPE VL, VLS, VLF
INLINE CENTRIFUGAL PUMPS REPLACEMENT PARTS GUIDE PACO TYPE VL, VLS, VLF This guide is valid for all PACO products beginning with product codes 16, 17 and 127 only. See back cover for explanation and identification.
More informationTYPE VSM / VSMS PARTS GUIDE
3/09 Supercedes 1/06 TYPE VSM / VSMS PARTS GUIDE VERTICAL SPACE MISER PUMPS PACO TYPE VSM, VSMS This guide is valid for all PACO products beginning with product codes 131 and 132 See back cover for explanation
More informationEND SUCTION PUMP WITH INTEGRATED VARIABLE FREQUENCY DRIVE REPLACEMENT PARTS GUIDE
TYPE LFE LFE END SUCTION PUMP WITH INTEGRATED VARIABLE FREQUENCY DRIVE REPLACEMENT PARTS GUIDE This guide is valid for all Grundfos CBS Inc. products beginning with product code 21. Grundfos CBS Inc. End
More informationPACO PUMPS REPLACEMENT PARTS GUIDE. A1b.2 4/06 Supercedes 8/05. Here are some guidelines and suggestions:
END SUCTION REPLACEMENT PARTS GUIDE CAT#: STOCK#: SER#: GPM: TDH: IMP. DIA: While End Suction Pumps are designed and built to provide maximum life while requiring minimum attention and service, replacement
More informationPACO PUMPS. A4b.2/A5b.2 4/06 Supercedes 9/05 TYPE OL, OLN, LN (PC 37, 38, 39, 12) REPLACEMENT PARTS GUIDE
TYPE OL, OLN, LN (PC 37, 38, 39, 12) REPLACEMENT PARTS GUIDE While In-Line Pumps are designed and built to provide maximum life while requiring minimum attention and service, replacement parts may at times
More informationTO REPLACE A MECHANICAL SEAL Select the correct Seal Kit, which contains all gaskets and impeller hardware. Shaft sleeve inspection is suggested.
END SUCTION PUMPS REPLACEMENT PARTS GUIDE TYPE LC, LF, LCV This guide is valid for all Grundfos CBS products beginning with product codes 10, 11 and 20. See back cover for explanation and identification.
More informationThis guide is valid for all Grundfos CBS products beginning with product codes 10, 11 and 20. See back cover for explanation and identification.
END SUCTION PUMPS REPLACEMENT PARTS GUIDE TYPE LC, LF, LCV This guide is valid for all Grundfos CBS products beginning with product codes 10, 11 and 20. See back cover for explanation and identification.
More informationFeatures: Applications: Irrigation. Commercial. Construction. Municipal. Mining
Frame Mount 7.5" BOOK: FMT-015 DATE: Mar. 1, 2012 Features: Volute: Ductile iron for heavy-duty service. Back pullout design. Can be rotated for ease of installation. Impeller: Enclosed design for high
More informationBulletin C Dean Pump Division. Heavy Duty, High Temperature Process Pumps. R4140 Telescoping Guard. R4140 C-Face Motor Support
Bulletin C 1.4.43 Dean Pump Division Heavy Duty, High Temperature Process Pumps R4140 Telescoping Guard R4140 C-Face Motor Support Dean Pump Series R Centrifugal Process Pumps Capacities to 5000 GPM (1135
More informationCENTRIFUGAL PUMPS 7.5" FRAME MOUNT SERIES FEATURES
FEATURES Volute: Ductile iron volute for heavy-duty service; back pullout design; can be rotated for ease of installation Impeller: Enclosed design for high efficiency; configured for superior NPSH characteristics;
More informationBerkeley Cast Iron Impeller B6EXQBH SAE ENGINE MOUNT. Flanged Case, Packing Construction. Table I. Page Date March 4, 2013 Supersedes 01/01/04
BEXQBH Page. 8 83 84 ( X scale ) 3 3 5A 8 B/M Mtg. Spline B00 H05398 H053 -/-0T 3" Kit available for this model, P/N B9. Refer to Supplement-C of this section for list of components included with kit.
More informationSpecifications Information and Repair Parts Manual , , , &
Please read and save this Repair Parts Manual. Read this manual and the General Operating Instructions carefully before attempting to assemble, install, operate or maintain the product described. Protect
More informationSeries 8150 Replacement Parts for 8150 Series Fire Pumps PARTS LIST CP-608B-PL
Series 8150 Replacement Parts for 8150 Series Fire Pumps PARTS LIST CP-608B-PL SERIES 8150 CROSS SECTION 0-952-3 0-952-4 0-952-5 2-904-2 0-952-2 0-952-1 0-952-6 2-001-0 2-916-1 2-904-1 2-123-5 0-905-0
More informationPROCESS PUMPS MODEL V200 ANSI B73.2
EAGLE PROCESS PUMPS V200 ANSI B73.2 POWER END Shaft Diameters Bearings Stuffing Box PUMP END Maximum Diameter Solids Minimum Casing Thickness Casing Corrosion Allowance Working Pressure Test Pressure
More informationB/M No. B H00925 M /8-10T 3" B H00920 M /8-10T 2-1/2" Part Number. Item. No. 800B
Threaded Case (NPT), Packing Construction Page 80. Supersedes 03/0/ 87 8 B/M Mtg. Bracket Spline Ext. B00 4 H0095 M0454-3/8-0T 3" B5999 5 H0090 M07-3/8-0T -/" 7 Kit available for this model, P/N B778 for
More information855 Filtrate Pump, Close Coupled and Overhead Mounted Pumps
855 Filtrate Pump, Close Coupled and Overhead Mounted Pumps Technical Specification Pages This page left intentionally blank. 1.0 Overview. The 855 Series is Carver s offering specifically designed to
More informationCENTRIFUGAL PUMPS CLOSE-COUPLED 9" FEATURES SPECIFICATIONS APPLICATIONS
FEATURES Volute: Heavy-duty cast iron construction; back pullout design; can be rotated for ease of installation Impeller: Enclosed, cast iron design for high efficiency; hydraulically balanced for reduced
More informationGoulds Small Capacity Double Suction Pump
Goulds 3410 Small Capacity Double Suction Pump 3410 Double Suction Pumps Designed for a Wide Range of Industrial, Municipal, Capacities to 7,000 GPM (1591 m3/h) Heads to 550 feet (168 m) Temperatures to
More informationB/M No. Shaft Kit available for this model, P/N B Refer to Supplement-C of this section for list of components included with kit.
BJQBM Page 0. Date March 4, 03 Supersedes 0/0/04 8B 3 3C 8 B/M Mtg. Spline B0 H0598 M083 -/-0T 3" B08 H059 M083 -/-0T 3" B08 3 H059 M083 -/-0T 3" B08 4 H0595 M083 -/-0T 3" Kit available for this model,
More informationCentrifugal End Suction Fire Pumps
Centrifugal End Suction Fire Pumps 1 Centrifugal End Suction Fire Pumps Product Overview American-Marsh Model FP-REF End Suction pumps are used in a variety of fire protection services every day. These
More informationCENTRIFUGAL PUMPS SAE ENGINE DRIVE 10" FEATURES
FEATURES Volute: Heavy ductile iron construction; back pullout design; can be rotated for ease of installation Impeller: Ductile iron enclosed design for high efficiency; superior NPSH characteristics
More informationAURORA MODEL 410 SERIES ENGINEERING DATA MECHANICAL SEALS AND PACKING
AURORA MODEL 410 SERIES MECHANICAL SEALS AND PACKING Section 410 Page 71 Supersedes Section 410 Page 71 1 PACKING WITH OPTIONAL LANTERN RING SINGLE INSIDE UNBALANCED 3 SINGLE INSIDE BALANCED TAP OPTIONALLY
More information3312 Model. pumping Model Model AURORA Series HORIZONTAL AND VERTICAL CLOSE-COUPLED PUMPS
3312 Model pumping 3314 Model 3311 Model AURORA 3310 Series HORIZONTAL AND VERTICAL CLOSE-COUPLED PUMPS WWW.AURORAPUMP.COM AURORA 3310 Series Horizontal and Vertical Close-Coupled Pumps Capacities to 3800
More informationSERIES 4300 TC/TSC/TCZ MOTORS
FILE : 6043.137 DATE: July 7, 2010 SUPERSEDES: 6043.137 DATE: June 24, 2010 PARTS LIST SERIES 4300 DESIGN TC/TSC/TCZ MOTORS VERTICAL IN-LINE SPLIT COUPLER "DBL" DESIGNATION - GROUPS 25 TO 51 TS and TSC
More informationHORIZONTAL SPLIT CASE SINGLE STAGE DOUBLE SUCTION Type AE CHECKING LIST
Section Tab 1200 SINGLE STAGE DOUBLE SUCTION Section 1210 List Prices Removed 07-01-02 Use Rapid Section 1220 Data Page 0.1 & (Blank)(03-30-07) 1 & 2 (03-30-07) 2.1 & 2.2 (03-30-07) 2.21 & 2.22 (03-30-07)
More informationBulletin C Dean Pump Division. ANSI/ASME B73.1 Horizontal Process. ph2140 Telescoping Guard. ph2140 C-Face Adapter
Bulletin C 1.2.34.5 Dean Pump Division ANSI/ASME B73.1 Horizontal Process ph2140 Telescoping Guard ph2140 C-Face Adapter Dean Pump Series ph Centrifugal Process Pumps Capacities to 3200 GPM (726 m 3 /hr)
More informationNC State University Design and Construction Guidelines Division 23 Hydronic Pumps
1.0 Purpose A. The following guidelines apply to the selection of pumps primarily for circulating water. It is the goal of NC State to purchase pumps that are selected to provide a long service life, minimal
More informationBell & Gossett Parts List CP-106F-PL. Replacement Parts for. Series 60 Maintenance Free In-Line Mounted Centrifugal Pumps
Bell & Gossett Parts List CP-106F-PL Replacement Parts for Series 60 Maintenance Free In-Line Mounted Centrifugal Pumps SERIES 60 How to use this PARTS LIST The pump nameplate identifies the pump by model
More informationDischarge diameters 1.5", 2", 3", 4", 5", 6", 8", 10", 12" & 14" HP 1 to 500. Split Coupled Vertical In-Line Pumps BVL
Discharge diameters 1.5", 2", 3", 4", 5", 6", 8", 10", 12" & 14" HP 1 to 500 Split Coupled Vertical In-Line Pumps BVL Split Coupled Vertical In-Line Pumps Capacities up to 12,000 GPM Heads up to 560 ft
More informationDrive Motor Type 3 (115/230V, 1 Phase TEFC) Motor Type 4 (230/460V, 3 Phase TEFC) Options Description Price Adders
PMU (Pump & Motor Unit) Prices 1000 4000 3000 Drive Motor Type 3 (115/230V, 1 Phase TEFC) Motor Type 4 (230/460V, 3 Phase TEFC) N HP 1725 rpm Consult Factory N/A L HP 1725 rpm Consult Factory Consult Factory
More informationHigh Temperature Air-Cooled Hot Oil Pumps
Bulletin C 1.4.42 Dean Pump Division High Temperature Air-Cooled Hot Oil Pumps No Water Cooling Required RA3 RA2 DEAN PUMP SERIES RA FAN COOLED HIGH TEMPERATURE HOT OIL PUMPS No Liquid Cooling Required
More informationTECHNICAL BROCHURE B36/ /3742 CLOSE-COUPLED AND FRAME-MOUNTED CENTRIFUGAL PUMPS
TECHNICAL BROCHURE B36/3742 3642/3742 CLOSE-COUPLED AND FRAME-MOUNTED CENTRIFUGAL PUMPS FEATURES Compact Design: Close coupled, space saving design provides easy installation. Flexible couplings and bedplates
More informationTruck Pumps Water XS439 XS869
Truck Pumps Water XS439 XS869 Water Truck 9" BOOK: WTP-005 DATE: Jan. 1, 2012 Features: Volute: Heavy cast iron construction. Back pullout design. Can be rotated for ease of installation. Impeller: Double
More informationJohn Crane Type 5620 and 5620PR Dual O-Ring Cartridge Seal Assembly and Installation Instructions
I-5620/5620PR-A John Crane Type 5620 and 5620PR Dual O-Ring Cartridge Seal Assembly and Installation Instructions Foreword These instructions are provided to familiarize the user with the seal and its
More informationTECHNICAL BROCHURE B36/3742 R2 3642/3742 CLOSE-COUPLED AND FRAME-MOUNTED CENTRIFUGAL PUMPS
TECHNICAL BROCHURE B36/3742 R2 3642/3742 CLOSE-COUPLED AND FRAME-MOUNTED CENTRIFUGAL PUMPS FEATURES Compact Design: Close coupled, space saving design provides easy installation. Flexible couplings and
More informationREPAIR PARTS R36/3756 R /3756 S, M & L-Group REPAIR PARTS
REPAIR PARTS R6/756 R1 656/756 S, M & L-Group REPAIR PARTS PUMP END PARTS FOR CLOSE-COUPLED OR FRAME MOUNTED CONFIGURATION 656/756 S-Group Note: For S-Group power frame individual parts see S-Group Power
More informationModels 9202C, 9203C, 9252C-C, and 9253C-C
Models 0C, 03C, C-C, and 3C-C 3 0 3 consists of () Ref. O-ring, () Ref. Mechanical Seal (Viton) and () Ref. Gasket. NOTE: When ordering parts, give quantity, part number, decription, and complete model
More informationPWA-IL B73.2 IN-LINE
PWA-IL ANSI/ASME B73.2 IN-LINE PROCESS PUMP PWA-IL ANSI/ASME B73.2 IN-LINE PROCESS PUMP COMPETITIVE ADVANTAGES vs. Ductile Iron n High-strength, impact resistant liquid ends for improved durability and
More informationDI DI PUMP PARTS PRICE LIST
ITEM 1 2 2A 5050 Pump Body, 2" NPT Mech. Seal 1 40091 1 5050 Pump Body, 2" 150# RF Flg. Mech. Seal 1 40791 1 5050 Pump Body, 2" NPT, Packing 1 40088 1 5050 Pump Body, 2" 150# RF Flg., Packing 1 40793 1
More informationHigh Temperature Air-Cooled Hot Oil Pumps
Bulletin C 1.4.42 Dean Pump Division High Temperature Air-Cooled Hot Oil Pumps No Water Cooling Required RA296 RA3146 RA3186 RA296 The smaller, foot mounted economy version of the air-cooled RA series
More informationA-C Fire Pump Systems FP 2.4 Page 1
ENG. DATA Page 1 February, 1996 Supersedes 5/95 issue FP 2.4 Page 2 A-C Fire Pump Systems 49-139 140-206 54-130 131-256 71-150 10WALC 10WALC 11CLC 11CLC 11CHC 500 500 750 Max Working Pressure (G) 175 psi
More informationCLOSED COUPLED CENTRIFUGAL PUMPS
SECTION B PAGE 0 ISSUED /0 REPLACES /0 www.pumpagents.com PumpAgents.com - Click here for Pricing/Ordering SERIES: G6--/ thru G9-F 0 Third Street Piqua, Ohio 6-060 CLOSED COUPLED CENTRIFUGAL PUMPS 00RPM
More informationParts for Fig. 4565, 4566 & 4568 Industrial Section 40L Bulletin 95. Repair Parts.
www.cranepumps.com Parts for Fig. 55, 5 & 5 Item No. 1 2 * 1 19 23 * 2 32 33 * 39 2 9 70 71 * 73 101 101A 105 11 19 19A 170 199 212 21 219 22 * 21 22 2 250 25 255 25 * 257 25 20 25 27 2 270 277 25 29 29
More informationHigh-Temperature and Pressure Paper Stock / Process Pump
3186 High-Temperature and Pressure Paper Stock / Process Pump 3186 Designed to handle High-Temperature and High-Pressure services of the Pulp & Paper Industries. Capacities to 3000 m³/h (13,000 GPM) Heads
More informationCP-506B-PL. Series HSCS. Horizontal Split Case Pumps. Replacement Parts
Series HSCS Horizontal Split Case Pumps Replacement Parts PARTS List CP-506B-PL PARTS LIST CP-505-PL Index Description Page No. Exploded View....3 Parts List for 6x10x22, 8x12x22M, 8x12x22L, 8x12x27, and
More informationCLOSED COUPLED CENTRIFUGAL PUMPS
SECTION B PAGE 0 ISSUED /0 REPLACES /0 www.pumpagents.com PumpAgents.com - Click here for Pricing/Ordering SERIES: G6--/ thru G9-F 0 Third Street Piqua, Ohio 6-060 CLOSED COUPLED CENTRIFUGAL PUMPS 00RPM
More informationCENTRIFUGAL PUMPS CLOSE-COUPLED 7.5" FEATURES
FEATURES Volute: Ductile iron for heavy-duty service; back pullout design; can be rotated for ease of installation Impeller: Enclosed design for high efficiency; configured for superior NPSH characteristics;
More information3340 Series Single Stage End Suction Pumps
3340 Series Single Stage End Suction Pumps Bulletin 3340/Rev. A Model 3344 Aurora 3340 Pump Setting New Standards of Efficiency Liquid handling requirements are much more involved than they were five years
More informationBerkeley Cast Iron Impeller B6ZPL ELECTRIC MOTOR DRIVE. Flanged Case, Packing Construction. Table I. Table II
B6ZPL Flanged Case, Packing Construction Page 350. 80B 80B 3 B509 0 -/4" 6."x8.5" M078 B5 0 3 -/4" 6."x8.5" M078 B548 5 3 -/4" 7.56"x8.56" M079 B54 0 3 -/4" 8.00"x9.00" M04348 7 80A 80A 6 Case, Volute
More informationTaco CI Series End Suction, Base Mounted Pumps
Taco CI Series End Suction, Base Mounted Pumps Taco CI Series Pumps are similar to the Bell & Gossett 1531 series of base mounted pumps. Used in commercial, industrial and institutional applications where
More informationASME END SUCTION PUMPS Catalogue K-90
ASME END SUCTION PUMPS Catalogue K-90 ASME B3.1-01 ISO 9001:008 REGISTERED COMPANY Engineered Pumps for Industrial and Municipal Services ASME B3.1 / ANSI END SUCTION PUMPS This catalogue provides the
More informationBerkeley Cast Iron Impeller B1-1/2ZPH ELECTRIC MOTOR DRIVE. Threaded Case (NPT), Packing Construction. Table I. Table II
Cast Iron Impeller B-/ZPH Threaded Case (NPT), Packing Construction Page 50. Date March 4, 03 Supersedes 07/0/ 3 B/M HP PH RPM "U" Dim. Imp. Dia. Imp. B53759 5 3 3600 -/4" 7.94" M07666 B596 0 3 3600 -/4"
More informationGoulds 3181 High-temperature/Pressure Paper Stock/ Process Pumps
High-temperature/Pressure Paper Stock/ Process Pumps Designed to Handle High Temperature and High Pressure Services of the Pulp & Paper Industries Capacities to 13,000 GPM (3000 m 3 /h) Heads to 410 feet
More informationHigh Temperature Chemical Process Inline Pumps
Bulletin C-1.2.21. Dean Pump Division High Temperature Chemical Process Inline Pumps Series DL Series DL High Temperature Chemical Process Inline Pumps Capacities to 6 GPM (182 m 3 /hr) Heads to feet (167
More informationBulletin BX-420C Bell & Gossett. VSC /VSCS Pumps Technical Bulletin. Bell & Gossett. Part of the. Equipment Selection Program
Bulletin BX-4C Bell & Gossett VSC /VSCS Pumps Technical Bulletin Part of the Bell & Gossett Equipment Selection Program VSC/VSCS Construction Materials STANDARD SEAL CONFIGURATION PART NAME STANDARD CONSTRUCTION
More information3800 Series. Single Stage End Suction Pumps. Capacities to 4200 G.P.M. (954 m 3 /hr) Heads to 520 Feet (180 Meters) Temperatures to 300 F (149 C)
3800 Series Single Stage End Suction Pumps Capacities to 200 G.P.M. (95 m 3 /hr) Heads to 520 Feet (180 Meters) Temperatures to 300 F (19 C) MODEL 380 Aurora 3800 Pump Setting New Standards of Efficiency
More informationCENTRIFUGAL PUMPS 13" CLOSE-COUPLED FEATURES
FEATURES Volute: Cast iron for heavy-duty service; back pull-out design; can be rotated for ease of installation; split volutes for reduction in radial bearing load (6 x 8-13 and 8 x 10-13) Impeller: Enclosed
More informationCALCULATION OF BOWL HEAD OR DISCHARGE HEAD
February, 1996 Supersedes 5/95 issue CALCULATION OF BOWL HEAD OR Pressure Gauge hd (Discharge Head) hl (LIFT) hp (Internal Pump Loss) Setting Sump Depth Pump O.A.L. Pumping Water Level hb (Bowl Head) For
More informationHigh Head Centrifugal Pedestal Pumps
Please read and save this Repair Parts Manual. Read this manual and the General Operating Instructions carefully before attempting to assemble, install, operate or maintain the product described. Protect
More informationBulletin BX-512H. Bell & Gossett. Series HSC-S Pumps Technical Bulletin. Bell & Gossett. Part of the. Equipment Selection Programs
Bulletin BX-1H Bell & Gossett Series HSC-S Pumps Technical Bulletin Part of the Bell & Gossett Equipment Selection Programs TABLE OF CONTENTS Useful Pump Formulas...............................................
More informationGoulds 3186 High-temperature/Pressure Paper Stock/ Process Pumps
Lenntech info@lenntech.com Tel. +31-152-610-900 www.lenntech.com Fax. +31-152-616-289 Goulds 3186 High-temperature/Pressure Paper Stock/ Process Pumps Goulds 3186 Designed to Handle High Temperature and
More informationSERIES: WG6-2 SELF-PRIMING CENTRIFUGAL PUMPS
420 Third Street Piqua, Ohio 436-0603 www.pumpagents.com PumpAgents.com - Click here for Pricing/Ordering SERIES: WG6-2 SECTION 4A PAGE ISSUED 2/03 REPLACES 2/0 SELF-PRIMING CENTRIFUGAL PUMPS 300RPM -
More informationDELTA O-RING CARTRIDGE SEAL ASSEMBLY AND INSTALLATION INSTRUCTIONS INTRODUCTION:
DELTA O-RING CARTRIDGE SEAL ASSEMBLY AND INSTALLATION INSTRUCTIONS INTRODUCTION: These instructions are provided to familiarize the user with the seal and its use. The instructions must be read carefully
More informationbarmesapumps.com WHAT IS AN ANSI PUMP
WHAT IS AN ANSI PUMP In 1977, the American National Standard Institue (ANSI) established criteria for centrifugal pumps in terms of dimension, chemical composition of the materials and safety specifications,
More informationHYPRO SPRAYER PUMPS FIMCO. Code # MFG Part # Description List Price
HYPRO SPRAYER PUMPS 82 IMPORTANT NOTE: Use cast iron pumps for general spraying. Use Ni-Resist and XL (Silver series) pumps for liquid fertilizers, soil fumigants and insecticides containing phosphates.
More informationFMC Technologies Bean piston pumps are unsurpassed within the vertical drilling markets.
FMC BEAN FMC Technologies Bean piston pumps are unsurpassed within the vertical drilling markets. WATER esigned for continuous duty applications, the FMC Technologies Bean piston line increases drilling
More informationIndex - Section 14 End Suction Pump Semi-Open Impeller
Index - Section End Suction Pump Semi-Open Impeller ITEM S Product Numbering System...1 Typical Architects / Engineers Specifi cations - Series 4000...2 Seal Application...3-4 Technical Charts...5-6 Pump
More informationANSI Centrifugal Process Pumps. 911 Series
ANSI Centrifugal Process Pumps 9 Series WHAT IS AN ANSI PUMP In 977, the American National Standard Institue (ANSI) established criteria for centrifugal pumps in terms of dimension, chemical composition
More informationTWO-PRESSURE VALVE ASSEMBLY
BULLETIN A-1 TWO-PRESSURE VALVE ASSEMBLY FOR WATER, 95/5 OR OIL SERVICE 35 PSI (2.4 Bar) air recommended on diaphragm The Valv-Trol Two-Pressure Operating Valve is actually an assembly of three of our
More informationG&L Pumps. TECHNICAL Brochure BAC8100. Series A-C 8100 SPLIT CASE PUMPS
TECHNICAL Brochure BAC8 Series A-C 8 SPLIT CASE PUMPS TABLE OF CONTENTS Useful Pump Formulas 2 Performance Curves 3-5 Materials of Construction (Standard) 6 Materials of Construction (Optional) 7 Pump
More informationHYPRO SPRAYER PUMPS C-A Cast Iron Pump Less Coupler $ N-A Ni-Resist Pump Less Coupler $
HYPRO SPRAYER PUMPS 81 IMPORTANT NOTE: Use cast iron pumps for general spraying. Use Ni-Resist and XL (Silver series) pumps for liquid fertilizers, soil fumigants and insecticides containing phosphates.
More informationBearing Frame Mount CAST IRON IMPELLER B4EYRMBM TYPE B SINGLE STAGE CENTRIFUGAL PUMP TABLE I
Page 0. Date November, 009 B4EYRMBM Packing Construction 3 8 B/M No. Rotation Case Diameter B50 CW M5 L09.88 80 A 3 See Supplement B 9 3 See Table I Shaft (Not sold separately) See Note 9 Cover, Suction
More information255 Cartridge Dual Seal
MECHANICAL SEAL INSTALLATION INSTRUCTIONS 255 Cartridge Dual Seal Installation Instructions SEAL INSTALLATION Preparation Determine if the pump is in good condition. A. Check the shaft or sleeve. 1. Remove
More informationBasic Hydraulic Features. Basic Mechanical Features
APRIL 2006 1.0 Overview The ETA is designed for flow rates that fall beyond the range of most end suction pumps. Performance extends to 9,500 GPM, 440 feet of head, and 88% efficiency. This range is covered
More informationHYPRO SPRAYER PUMPS FIMCO. Code # MFG Part # Description List Price
IMPORTANT NOTE: Use cast iron pumps for general spraying. Use Ni-Resist and XL (Silver series) pumps for liquid fertilizers, soil fumigants and insecticides containing phosphates. Repair Kits Include Super
More information5" Submersible Turbine Pump 120 GPM
5" Submersible Turbine Pump 120 GPM Submersible Turbine Pumps Features: n 100% Franklin Electric factory wet tested with test results shipped with each pump n Premium ductile iron casting for longer life
More information430B SERIES HORIZONTAL SPLIT CASE PUMP
430B SERIES TWO Stage - DIAGONALLY HORIZONTAL SPLIT CASE PUMP REPAIR PARTS INDEX NOTE! Read and understand the pump and motor instructions before attempting to install, disassemble or repair the pump.
More informationSERIES CS CLOSE COUPLED TURBINE PUMPS
PumpAgents.com - Click here for Pricing/Ordering SERIES CS CLOSE COUPLED TURBINE PUMPS CS- 7 RPM - 60Hz. CS - 0 RPM - 60Hz. (See Individual curves for symbol number) Symbol No. 6 7 0 6 7 MAXIMUM HEAD H.P.
More information225 CARTRIDGE DUAL SEAL
225 CARTRIDGE DUAL SEAL MECHANICAL SEAL INSTALLATION INSTRUCTIONS PREPARATION 1 2 500.010" 0,25 mm 3 4.32 µ" 0,8 µm R a 1000 + ±.001".002" 0,025mm 0,050mm CAUTIONS These instructions are general in nature.
More information5" Submersible Turbine Pump 220 GPM
5" Submersible Turbine Pump 220 GPM Submersible Turbine Pumps Features: n 00% Franklin Electric factory wet tested with test results shipped with each pump n Premium ductile iron casting for longer life
More informationRDS. Radially Divided Seals.
RDS Radially Divided Seals Minimum parts to assemble Patented assembled spring retainer External, visible, indicator of correct installation Balanced stationary design with large internal clearances Unique
More informationRS Multi-Stage, Ring Section Pumps
RS Multi-Stage, Ring Section Pumps Technical Specification Pages This page left intentionally blank. 1.0 Overview. The RS Series is Carver s multi-stage pump for fluids at moderate to high pressures. The
More informationFire Protection. FP-XA End Suction
Fire Protection FP-XA End Suction PRODUCT BULLETIN MODEL FP-XA END SUCTION CPS Model FP-XA End Suction pumps are used in a variety of fire fighting applications. These rugged and efficient centrifugal
More informationModel 3196 STi Size 1x1.5-6 OUTLINE DRAWING. Weights and Measurements. Pump Specification. Notes and References. Motor Specification
OUTLINE DRAWING Pump Specification SUCT.FLANGE SIZE 1.5'' DRILLING ANSI 150# FACING FF FINISH SERRATED DISCH.FLANGE SIZE 1'' DRILLING ANSI 150# FACING FF FINISH SERRATED PUMP ROTATION ( LOOKING AT PUMP
More informationGH General Horizontal, Close Coupled and Frame Mounted Pumps
GH General Horizontal, Close Coupled and Frame Mounted Pumps Technical Specification Pages This page left intentionally blank. 1.0 Overview. The GH Series is Carver s horizontal, end suction pump for handling
More informationSUGGESTED SPECIFICATIONS
PART 1 - GENERAL 1.01 SCOPE A. Pumps to be supplied under this specification shall be of a severe duty, recessed cupped impeller design suitable for use in (SLUDGE, GRIT, ETC. APPLICATIONS) with a 20 year
More informationDI PUMP PARTS PRICE LIST
ITEM 1 2 2A PUMP 5040 Pump Body, 1-1/2" NPT Mech. Seal 1 40058 1 5040 Pump Body, 1-1/2" NPT, Packing 1 40057 1 5040 Pump Body, 1-1/2" 150# Flg., Mech. Seal 1 40787 1 5040 Pump Body, 1-1/2" 150# Flg., Packing
More information4410 TwinHydrostatic Gas Seal
IS0 9001 CERTIFIED CHESTERTON FLUID SEALING DIVISION INSTALLATION INSTRUCTIONS 4410 TwinHydrostatic Gas Seal SEAL INSTALLATION Preparation Determine if the pump is in good condition. A. Check the shaft
More informationSERIES CS CLOSE COUPLED TURBINE PUMPS
PumpAgents.com - Click here for Pricing/Ordering SERIES CS CLOSE COUPLED TURBINE PUMPS CS- 7 RPM - 60Hz. CS - 0 RPM - 60Hz. (See Individual curves for symbol number) Symbol No. 6 7 8 0 6 7 8 MAXIMUM HEAD
More informationDuctile Iron, Jacketed Pumps: Catalog Section 1602 Cast Iron, Non-Jacketed Pumps: Catalog Section 1401 HL4126A
Page 1601.1 TABLE OF CONTENTS Features & Benefits...2 Port Location Options...2 Model Number Key...3 Standard Materials of Construction...3 Cutaway View & Pump Features...4 Special Materials & Options
More informationSelf-Priming Fiberglass Pumps
Fybroc Division SERIES 16 Self-Priming Fiberglass Pumps B U L L E T I N 16B1 FYBROC THE LEADER IN CORROSION-RESISTANT FIBERGLASS PUMPING EQUIPMENT Fybroc is the leading manufacturer of fiberglass reinforced
More informationPARTS LIST SERIES 5240
File No. 6052.123 Date: January 6, 2003 Supersedes: 6052.123 Date: June 1, 1996 SUMP PUMP FOR PUMPS SERIAL NUMBER 71854 AND LATER NEW DESIGN 5240 SUMP PUMP PARTS IDENTIFICATION ITEM DESCRIPTION PAGE ITEM
More information900 Series Split Case Fire Pump Systems
BULLETIN 900/REV. E 900 Series Split Case Fire Pump Systems MODEL 481 MODEL 483 FM Approved U L Listed motralec 4 rue Lavoisier. ZA Lavoisier. 95223 HERBLAY CEDEX Tel. : 01.39.97.65.10 / Fax. : 01.39.97.68.48
More informationEDWARDS GEAR PUMPS REPAIR PARTS INDEX
SECION EDWARDS PAGE EDWARDS GEAR PUMPS REPAIR S INDEX READ AND UNDERSAND HE PUMP AND MOOR INSRUCIONS BEFORE AEMPING O INSALL, DISASSEMBLE OR REPAIR HE PUMP SECION EDWARDS PAGE 2 EDWARDS GEAR PUMPS MODELS,
More informationCENTRIFUGAL PUMPS HYDRAULIC DRIVEN 9" FEATURES SPECIFICATIONS APPLICATIONS
FEATURES Volute: Heavy-duty cast iron construction; back pullout design; can be rotated for ease of installation Impeller: Enclosed, cast iron design for high efficiency; double keyed for improved reliability
More informationPUMPS FOR INDUSTRY. The Vertical Pump Specialists CONTENTS: Introduction & User List. Product Overview. Vertical Process Pumps...
PUMPS FOR INDUSTRY CONTENTS: The Vertical Pump Specialists Introduction & User List Product Overview Vertical Process Pumps... Series 600 Vertical Sewage Pumps... Series 700 Vertical Sump Pumps... Series
More informationPWA ANSI / ASME B73.1 PROCESS PUMP
PWA ANSI / ASME B73.1 PROCESS PUMP COMPETITIVE ADVANTAGES Carbon Steel vs. Ductile Iron n High strength, impact resistant Carbon Steel liquid ends for improved durability and pressure containment at no
More informationTYPE 5625/5625P DUAL METAL BELLOWS CARTRIDGE SEAL
Foreword TYPE 5625/5625P These instructions are provided to familiarize the user with the seal and its designated use. The instructions must be read and applied whenever work is done on the seal, and must
More informationSeries e-1510 REPLACEMENT PARTS FOR STANDARD DESIGN PUMPS PARTS LIST CP-208G-PL
Series e-1510 REPLACEMENT PARTS FOR STANDARD DESIGN PUMPS PARTS LIST CP-208G-PL PARTS LIST CP-208G-PL SERIES e-1510 Index Nameplate Data.................................................. Exploded Views...................................................
More information