Series 8150 Replacement Parts for 8150 Series Fire Pumps PARTS LIST CP-608B-PL
|
|
|
- Lawrence Lynch
- 5 years ago
- Views:
Transcription
1 Series 8150 Replacement Parts for 8150 Series Fire Pumps PARTS LIST CP-608B-PL
2 SERIES 8150 CROSS SECTION
3 Replacement Parts List Series 8150 Item No. Part Description Qty Material 8x6x14F-L 8x6x14F-S Casing Asm 125Flg DI 1 Ductile Iron AC5909 AC Casing Asm 250Flg DI 1 Ductile Iron AC5910 AC Casing Asm Flg DI 1 Ductile Iron AC5911 AC Pipe Plug 1/2NPT Brass 2 Brass CP CP Pipe Plug 1NPT SS 2 Stainless Steel CP CP Pipe Plug 1/4NPT SS 8 Stainless Steel P39050 P Gasket: Suction, Casing 1 Vellumoid AC5912 AC Gasket: Discharge, Casing 1 Vellumoid AC5933 AC Shaft 1 Steel AC5924 AC Impeller Brz w/o rings 1 Silicon Brass AC5936 AC Impeller Key 3/8x5 1 Steel AC5916 AC Shaft Sleeve 2 Bronze AC5925 AC O-Ring Sleeve (3.500x.103) 2 Buna-N AC5940 AC Shaft Sleeve Nut 2 Bronze AC5926 AC Setscrew 1/4-28UNFx3/16 SS 4 Stainless Steel DJ0203 DJ Slinger 2 Neoprene AC8670 AC Ring Casing: Brz 2 Bronze AC5913 AC Pin W/R 2 Stainless Steel CP CP Lip Seal 2 Rubber/Steel P P Bearing Bracket 2 Cast Iron AC5921 AC Bearing 6309 w/shield 2 Steel P P Snap Ring Beveled 1 Steel AC5938 AC Housing Bearing Inboard 1 Cast Iron AC5918 AC Housing Bearing Outboard 1 Cast Iron AC5919 AC CAPSCREW,HEX HD3/8-16UNCX3-1/4 8 Steel DJ0083 DJ Grease Fitting 2 Steel P70614 P CAPSCREW HEX HD 1/2-13NCX1-1/2 8 Steel K04500 K BOLT, CASING JOINT 7/8-9UNCx2.5 12Pt 38 Steel CP CP BOLT, CASING JOINT 7/8-9UNCx6.5 12Pt 4 Steel AC5937 AC PIN, TAPER 2 Steel CP CP Packing 1/2 10 Grade "F" AC6130 AC Lantern Ring 2 PTFE AC5934 AC Gland 4 Stainless Steel AC5923 AC STUD 1/2-13UNCx2-3/4 SS 4 Stainless Steel AC6069 AC /2 HEX NUT 4 Stainless Steel DJ0248 DJ Washer 1/2 4 Stainless Steel DJ0308 DJ HEX BUSHING 1/2NPT x 1/4NPT 1 Steel J89428 J NIPPLE 1/4NPT x 1-1/2 1 Steel DL0021 DL TEE 1/4NPT 1 Steel S39740 S NEEDLE VALVE 1/4NPT-1/4TUBE 2 Brass TUBING 1/4 COPPER 4 Copper X42104 X CONNECTOR MALE COMP 1/4ODX1/4NPT 2 Brass AC0535 AC Coupler Key 3/8X3/8X Steel CP CP
4 Replacement Parts List Series 8150 Item No. Part Description Qty Material Casing Asm 125Flg DI 1 Ductile Iron AC Casing Asm 250Flg DI 1 Ductile Iron AC Casing Asm Flg DI 1 Ductile Iron AC x10x22F Pipe Plug 1/2NPT Brass 2 Brass CP Pipe Plug 1NPT SS 2 Stainless Steel CP Pipe Plug 1/4NPT SS 8 Stainless Steel P Gasket: Suction, Casing 1 Vellumoid AC Gasket: Discharge, Casing 1 Vellumoid AC Shaft 1 Steel AC Impeller Brz w/o rings 1 Silicon Brass AC Impeller Key 1/2x5-3/4 1 Steel AC Shaft Sleeve 2 Bronze AC O-Ring Sleeve (3.500x.103) 2 Buna-N AC Shaft Sleeve Nut 2 Bronze AC Setscrew 1/4-28UNFx3/16 SS 4 Stainless Steel DJ Slinger 2 Neoprene AC Ring Casing: Brz 2 Bronze AC Pin W/R 2 Stainless Steel CP Lip Seal 2 Rubber/Steel AC Bearing Bracket 2 Cast Iron AC Snap Ring Bearing 2 Steel AC Bearing 6316 w/shield 2 Steel P Snap Ring Beveled 1 Steel AC Housing Bearing Inboard 1 Cast Iron AC Housing Bearing Outboard 1 Cast Iron AC CAPSCREW,HEX HD3/8-16UNCX3-1/2 8 Steel P Grease Fitting 2 Steel P CAPSCREW HEX HD 1/2-13NCX1-1/2 8 Steel K BOLT, CASING JOINT 1-8UNCx Pt 42 Steel AC BOLT, CASING JOINT 1-8UNCx7 12Pt 4 Steel AC PIN, TAPER 2 Steel CP Packing 5/8 10 Grade "A" AC Lantern Ring 2 PTFE AC Gland 4 Stainless Steel AC Capscrew 1/2-13UNCx2-1/2 SS 4 Stainless Steel AC Washer 1/2 4 Stainless Steel P HEX BUSHING 1/2NPT x 1/4NPT 1 Steel J NIPPLE 1/4NPT x 1-1/2 1 Steel DL TEE 1/4NPT 1 Steel S NEEDLE VALVE 1/4NPT-1/4TUBE 2 Brass TUBING 1/4 COPPER 4 Copper X CONNECTOR MALE COMP 1/4ODX1/4NPT 2 Brass AC Coupler Key 3/4x3/4x4.5 1 Steel P
5 Xylem 1) The tissue in plants that brings water upward from the roots; 2) a leading global water technology company. We re a global team unified in a common purpose: creating advanced technology solutions to the world s water challenges. Developing new technologies that will improve the way water is used, conserved, and re-used in the future is central to our work. Our products and services move, treat, analyze, monitor and return water to the environment, in public utility, industrial, residential and commercial building services, and agricultural settings. With its October 2016 acquisition of Sensus, Xylem added smart metering, network technologies and advanced data analytics for water, gas and electric utilities to its portfolio of solutions. In more than 150 countries, we have strong, long-standing relationships with customers who know us for our powerful combination of leading product brands and applications expertise with a strong focus on developing comprehensive, sustainable solutions. For more information on how Xylem can help you, go to Xylem Inc N. Austin Avenue Morton Grove, Illinois Phone: (847) Fax: (847) A-C Fire Pump is a trademark of Xylem Inc. or one of its subsidiaries Xylem Inc. CP-608B-PL January 2018
CP-506B-PL. Series HSCS. Horizontal Split Case Pumps. Replacement Parts
Series HSCS Horizontal Split Case Pumps Replacement Parts PARTS List CP-506B-PL PARTS LIST CP-505-PL Index Description Page No. Exploded View....3 Parts List for 6x10x22, 8x12x22M, 8x12x22L, 8x12x27, and
PARTS LIST CP-210-PL. Series e Close Coupled Centrifugal Pumps. Replacement Parts
Series e-1535 Close Coupled Centrifugal Pumps Replacement Parts PARTS LIST CP-210-PL PARTS LIST CP-210PL SERIES e-1535 Index How to use this Parts List Page 3 e-1535 Pump Exploded View Page 4 Replacement
Series e-60. In-Line Mounted Centrifugal Pumps Maintenance Free Replacement Parts PARTS LIST CP-107-PL
Series e-60 In-Line Mounted Centrifugal Pumps Maintenance Free Replacement Parts PARTS LIST CP-107-PL Index How to Use This Parts List... 3 Exploded View Series e-60 Maintenance Free Pump... 4 Standard
PART LISTS D-421G-PL. Domestic Pump. Series B35 REPLACEMENT PARTS FOR. 2 ft. NPSH Centrifugal Pumps Styles PF and PVF and HB-35
PART LISTS D-21G-PL Domestic Pump Series B35 REPLACEMENT PARTS FOR 2 ft. NPSH Centrifugal Pumps Styles PF and PVF and HB-35 Index How To Use This Parts List........................................... 3
A-C Fire Pump. Fitting and Accessories A-C 100A
A-C Fire Pump Fitting and Accessories A-C 100A A-C Fire Pump Fitting and Accessories Table of Content Page Automatic Air Release Valve... 1 Suction And Discharge Gauge Assembly... 2 Casing Relief Valve...
Domestic. Pump Series CS Condensate Units SINGLE OR DUPLEX 1,000 THRU 150,000 SQ. FT. EDR-250 THRU 37,500 LB./HR.
Steel Receivers: Durable, Lightweight in sizes to 250 gallon (946L) Centrifugal Pumps: Provide generous running clearances. Standard 500 RPM for best hydraulic efficiencies, optional 750 RPM Float Switches:
Series e-1510 REPLACEMENT PARTS FOR STANDARD DESIGN PUMPS PARTS LIST CP-208G-PL
Series e-1510 REPLACEMENT PARTS FOR STANDARD DESIGN PUMPS PARTS LIST CP-208G-PL PARTS LIST CP-208G-PL SERIES e-1510 Index Nameplate Data.................................................. Exploded Views...................................................
REPAIR PARTS R36/3756 R /3756 S, M & L-Group REPAIR PARTS
REPAIR PARTS R6/756 R1 656/756 S, M & L-Group REPAIR PARTS PUMP END PARTS FOR CLOSE-COUPLED OR FRAME MOUNTED CONFIGURATION 656/756 S-Group Note: For S-Group power frame individual parts see S-Group Power
Marlow Series Prime Line
REPAIR PARTS RPRIMELINE Marlow Series Prime Line SELF-PRIMING CENTRIFUGAL PUMPS REPAIR PARTS Prime Line M2P M4P Pumps 27 50 49 27 54 1 8 10 6 17 4 67 5 24 37 63 53 51 2 7 46 2 PAGE 2 Prime Line 2" Pump
G&L Pumps. TECHNICAL Brochure BAC8100. Series A-C 8100 SPLIT CASE PUMPS
TECHNICAL Brochure BAC8 Series A-C 8 SPLIT CASE PUMPS TABLE OF CONTENTS Useful Pump Formulas 2 Performance Curves 3-5 Materials of Construction (Standard) 6 Materials of Construction (Optional) 7 Pump
NPE/NPE-F REPAIR PARTS REPAIR PARTS RNPE R5
NPE/NPE-F REPAIR PARTS REPAIR PARTS RNPE R5 TABLE OF CONTENTS NPE END SUCTION NPE Product Line Numbering System...3 NPE Seal Chart (Part of Numbering System)...3 Parts List...4 Optional Components...4
TECHNICAL BROCHURE B36/3742 R2 3642/3742 CLOSE-COUPLED AND FRAME-MOUNTED CENTRIFUGAL PUMPS
TECHNICAL BROCHURE B36/3742 R2 3642/3742 CLOSE-COUPLED AND FRAME-MOUNTED CENTRIFUGAL PUMPS FEATURES Compact Design: Close coupled, space saving design provides easy installation. Flexible couplings and
TECHNICAL BROCHURE B36/ /3742 CLOSE-COUPLED AND FRAME-MOUNTED CENTRIFUGAL PUMPS
TECHNICAL BROCHURE B36/3742 3642/3742 CLOSE-COUPLED AND FRAME-MOUNTED CENTRIFUGAL PUMPS FEATURES Compact Design: Close coupled, space saving design provides easy installation. Flexible couplings and bedplates
TECHNICAL BROCHURE B45-70HB R2 45HB, 70HB HIGH PRESSURE CENTRIFUGAL BOOSTER PUMP
TECHNICAL BROCHURE B45-7HB R2 45HB, 7HB HIGH PRESSURE CENTRIFUGAL BOOSTER PUMP FEATURES Multi-Stage Design: This configuration provides a steady, quiet and vibration-free operation for years of trouble-free
GB REPAIR PARTS REPAIR PARTS RGB R3
GB REPAIR PARTS REPAIR PARTS RGB R3 GB NUMBERING SYSTEM The various versions of the Series GB are identified by a product code number on the pump label. This number is also the catalog number for the pump.
REPAIR PARTS RJETPARTS R1. Jet Pump REPAIR PARTS
REPAIR PARTS RJETPARTS R1 Jet Pump REPAIR PARTS JETS JRS... 3 JRD... 4 JRSG... moved to obsolete book J+ and JS+... 5 JB... moved to obsolete book HSJ... 6 VJ... 7 SJ... GT Irri-Gator... 9 BF03S...10 The
TECHNICAL BROCHURE BAC2000. Series 2000 Closed Coupled. Series 2000 Frame Mounted. Series A-C 2000 SINGLE STAGE END SUCTION
TECHNICAL BROCHURE BAC0 Series 0 Closed Coupled Series 0 Frame Mounted Series A-C 0 SINGLE STAGE END SUCTION Series A-C 0 End Suction Close Coupled - Model 0 APPLICATIONS General Industry Water Supply
GB REPAIR PARTS REPAIR PARTS RGB R2
GB REPAIR PARTS REPAIR PARTS RGB R2 GB NUMBERING SYSTEM The various versions of the Series GB are identified by a product code number on the pump label. This number is also the catalog number for the pump.
CENTRIFUGAL PUMPS SAE ENGINE DRIVE 10" FEATURES
FEATURES Volute: Heavy ductile iron construction; back pullout design; can be rotated for ease of installation Impeller: Ductile iron enclosed design for high efficiency; superior NPSH characteristics
McDonnell & Miller Service Parts Catalog PARTS LIST MM-701D
McDonnell & Miller Service Parts Catalog PARTS LIST MM-70D Table of Contents Table of Contents Table of Contents 3 4 For Repl. Probe Part Weight Model Model No. Number Description lbs. (kg) PS-80-0 PA-800
Volute Casing Pumps LSN. according to iso 2828 / ISO 5199
Volute Casing Pumps LSN according to iso 2828 / ISO 5199 Technical Data Performance Range: m Capacity up to 500m 3 /h (1980USgpm) m Head up to 150m (492feet) m Speed 2950/3550rpm Pump Sizes: m DN 25 up
Features: Applications: Irrigation. Commercial. Construction. Municipal. Mining
Frame Mount 7.5" BOOK: FMT-015 DATE: Mar. 1, 2012 Features: Volute: Ductile iron for heavy-duty service. Back pullout design. Can be rotated for ease of installation. Impeller: Enclosed design for high
TECHNICAL BROCHURE B5-33GB R4 5GB, 7GB, 10GB, 18GB, 25GB, 33GB HIGH PRESSURE MULTI-STAGE BOOSTER PUMP
TECHNICAL BROCHURE B-33GB R4 GB, 7GB, GB, 1GB, 2GB, 33GB HIGH PRESSURE MULTI-STAGE BOOSTER PUMP FEATURES Multi-stage Design: Provides steady, quiet, vibration free, operation. applications. O-Ring Casing
B/M No. B H00925 M /8-10T 3" B H00920 M /8-10T 2-1/2" Part Number. Item. No. 800B
Threaded Case (NPT), Packing Construction Page 80. Supersedes 03/0/ 87 8 B/M Mtg. Bracket Spline Ext. B00 4 H0095 M0454-3/8-0T 3" B5999 5 H0090 M07-3/8-0T -/" 7 Kit available for this model, P/N B778 for
Hoffman Specialty Service Parts Catalog PARTS LIST HS-800C
Hoffman Specialty Service Parts Catalog PARTS LIST HS-800C Hoffman Specialty Table of Contents STEAM TRAPS FLOAT AND THERMOSTATIC SERIES PAGE INVERTED BUCKET SERIES PAGE C 6 B0 H B I B X 6 B 6 8 B 6 0
Pure Performance FLYGT 1300 SERIES
Pure Performance FLYGT 1300 SERIES Available EASY TO SELECT, QUICK DELIVERY, THE RIGHT PUMP FOR YOUR NEEDS Oustanding Value EFFICIENT, POWERFUL Reliable SOLIDS HANDLING, CONTINUOUS RUNNING 2 Readily available
33GS, 40GS, 55GS, 60GS, 75GS & 80GS GPM, 1 10 HP, 60 HZ, SUBMERSIBLE PUMPS
TECHNICAL BROCHURE B33-8GS FEATURES Powered for Continuous Operation: All ratings are within the working limits of the motor as recommended by the motor manufacturer. can be operated continuously without
Bearing Frame Mount CAST IRON IMPELLER B4EYRMBM TYPE B SINGLE STAGE CENTRIFUGAL PUMP TABLE I
Page 0. Date November, 009 B4EYRMBM Packing Construction 3 8 B/M No. Rotation Case Diameter B50 CW M5 L09.88 80 A 3 See Supplement B 9 3 See Table I Shaft (Not sold separately) See Note 9 Cover, Suction
Berkeley Cast Iron Impeller B6EXQBH SAE ENGINE MOUNT. Flanged Case, Packing Construction. Table I. Page Date March 4, 2013 Supersedes 01/01/04
BEXQBH Page. 8 83 84 ( X scale ) 3 3 5A 8 B/M Mtg. Spline B00 H05398 H053 -/-0T 3" Kit available for this model, P/N B9. Refer to Supplement-C of this section for list of components included with kit.
Bulletin BX-512H. Bell & Gossett. Series HSC-S Pumps Technical Bulletin. Bell & Gossett. Part of the. Equipment Selection Programs
Bulletin BX-1H Bell & Gossett Series HSC-S Pumps Technical Bulletin Part of the Bell & Gossett Equipment Selection Programs TABLE OF CONTENTS Useful Pump Formulas...............................................
CENTRIFUGAL PUMPS 7.5" FRAME MOUNT SERIES FEATURES
FEATURES Volute: Ductile iron volute for heavy-duty service; back pullout design; can be rotated for ease of installation Impeller: Enclosed design for high efficiency; configured for superior NPSH characteristics;
Replacement Parts List FI 4007 & FI 4007D. SUPERSEDES: NEW EFFECTIVE: December 31, 2018
Replacement Parts List 304-572 FI 4007 & FI 4007D SUPERSEDES: NEW EFFECTIVE: December 31, 2018 WHEN SELECTING AND ORDERING PARTS, ALWAYS REFER TO SERIAL ON NAMEPLATE FI 4007 BEARING FRAME J FI 4007D BEARING
TECHNICAL BROCHURE BHSJ. Basic Convertible Pump HSJ MULTI-STAGE CONVERTIBLE JET PUMPS - 60 HZ
TECHNICAL BROCHURE BHSJ Basic Convertible Pump HSJ MULTI-STAGE CONVERTIBLE JET PUMPS - 60 HZ FEATURES High Capacity and Pressure: Specifically designed to deliver high capacities at greater pressures.
Replacement Parts List FI 4009 & FI 4009C. SUPERSEDES: April 28, 2016 EFFECTIVE: October 18, 2016
A Taco Family Company Replacement Parts List FI 4009 & FI 4009C 304-403 SUPERSEDES: April 28, 2016 EFFECTIVE: October 18, 2016 WHEN SELECTING AND ORDERING PARTS, ALWAYS REFER TO SERIAL ON NAMEPLATE 00
SERIES 4300 TC/TSC/TCZ MOTORS
FILE : 6043.137 DATE: July 7, 2010 SUPERSEDES: 6043.137 DATE: June 24, 2010 PARTS LIST SERIES 4300 DESIGN TC/TSC/TCZ MOTORS VERTICAL IN-LINE SPLIT COUPLER "DBL" DESIGNATION - GROUPS 25 TO 51 TS and TSC
B/M No. Shaft Kit available for this model, P/N B Refer to Supplement-C of this section for list of components included with kit.
BJQBM Page 0. Date March 4, 03 Supersedes 0/0/04 8B 3 3C 8 B/M Mtg. Spline B0 H0598 M083 -/-0T 3" B08 H059 M083 -/-0T 3" B08 3 H059 M083 -/-0T 3" B08 4 H0595 M083 -/-0T 3" Kit available for this model,
CENTRIFUGAL PUMPS CLOSE-COUPLED 9" FEATURES SPECIFICATIONS APPLICATIONS
FEATURES Volute: Heavy-duty cast iron construction; back pullout design; can be rotated for ease of installation Impeller: Enclosed, cast iron design for high efficiency; hydraulically balanced for reduced
Pure performance STEADY 1300 SERIES
Pure performance STEADY 1300 SERIES Available EASY TO SELECT, QUICK DELIVERY, THE RIGHT PUMP FOR YOUR NEEDS Oustanding Value EFFICIENT, POWERFUL Reliable SOLIDS HANDLING, CONTINUOUS RUNNING 2 Readily available
Series 1510 Centrifugal Pumps
Series 1 Centrifugal Pumps B-207H Table of Contents Useful Pump Formulas... 2 Standard Features... 3 Technical Data... Materials of Construction... Selection Charts... 6 Performance Curves... 7 Centrifugal
e-sv REPAIR PARTS REPAIR PARTS ReSV R2
e-sv REPAIR PARTS REPAIR PARTS ReSV R2 Table of Contents Numbering System for 1 22SV Liquid End Only..........................................................3 Numbering System for 33 125SV Liquid End
CENTRIFUGAL PUMPS CLOSE-COUPLED 7.5" FEATURES
FEATURES Volute: Ductile iron for heavy-duty service; back pullout design; can be rotated for ease of installation Impeller: Enclosed design for high efficiency; configured for superior NPSH characteristics;
Discharge diameters 1.5", 2", 3", 4", 5", 6", 8", 10", 12" & 14" HP 1 to 500. Split Coupled Vertical In-Line Pumps BVL
Discharge diameters 1.5", 2", 3", 4", 5", 6", 8", 10", 12" & 14" HP 1 to 500 Split Coupled Vertical In-Line Pumps BVL Split Coupled Vertical In-Line Pumps Capacities up to 12,000 GPM Heads up to 560 ft
6" Single Phase Motors 6-10" Three Phase Motors
TECHNICAL BROCHURE BCP6-10MTR R2 FEATURES SINGLE PHASE: Single Phase, 6 motors available in 5 15 HP, 230 volt models. Require Control Boxes as shown on Order Number chart. THREE PHASE: Three Phase, 6,
(.LOWARA. a xylem brand
(.LOWARA a xylem brand New Z6, your 6 11 Stainless Steel Pump ncreased Life Cycle Cost - lower energy consumption No water contamination - No paint, no rust High sand handling capability 100 g/m 3 High
TECHNICAL BROCHURE BCP3PH R9. Three Phase 4" Motors, ½-10 HP 60 HERTZ, 3450 RPM
TECHNICAL BROCHURE BCP3PH R9 Three Phase 4" Motors, ½-10 HP 60 HERTZ, 3450 RPM FEATURES 304 SS casing and end bells for corrosion resistance Kingsbury type, 3 shoe, thrust bearing, see chart for ratings
Centrifugal End Suction Fire Pumps
Centrifugal End Suction Fire Pumps 1 Centrifugal End Suction Fire Pumps Product Overview American-Marsh Model FP-REF End Suction pumps are used in a variety of fire protection services every day. These
TECHNICAL BROCHURE BMPVN MPVN HIGH PRESSURE MULTI-STAGE PUMPS
TECHNICAL BROCHURE BMPVN MPVN HIGH PRESSURE MULTI-STAGE PUMPS A FULL RANGE OF PRODUCT FEATURES Performance Range: Capacities up to GPM ( m /h) Head up to feet ( m) Maximum speed up to RPM Sizes: From "
DI PUMP PARTS PRICE LIST
ITEM 1 2 2A PUMP 5040 Pump Body, 1-1/2" NPT Mech. Seal 1 40058 1 5040 Pump Body, 1-1/2" NPT, Packing 1 40057 1 5040 Pump Body, 1-1/2" 150# Flg., Mech. Seal 1 40787 1 5040 Pump Body, 1-1/2" 150# Flg., Packing
Aquavar ABII TECHNICAL BROCHURE BAQUABII R2 VARIABLE SPEED CONSTANT PRESSURE SYSTEMS
TECHNICAL BROCHURE BAQUABII R2 * Available up to 1 GPM systems Aquavar ABII VARIABLE SPEED CONSTANT PRESSURE SYSTEMS 1 and 2 HP, 1AB2 and 2AB2 Variable Speed Controllers 1AB2 and 2AB2 Prewired Pump/Controller
Replacement Parts List FI 1509 & FI 1509C. SUPERSEDES: September 21, 2016 EFFECTIVE: March 20, 2017
Replacement Parts List 304-364 FI 1509 & FI 1509C SUPERSEDES: September 21, 2016 EFFECTIVE: March 20, 2017 FI 1509 FI 1509C FI 1509C REQUIRED BEARING FRAME J BEARING FRAME H BEARING FRAME J 1 1 Impeller
Series HSC-S Pumps Technical Brochure
Series HSCS Pumps Technical Brochure BX512L Table of Contents Useful Pump Formulas 2 60 Cycle Performance Curves Series HSCS 3 50 Cycle Performance Curves Series HSCS 4 Series HSCS Materials of Construction
Bell & Gossett Parts List CP-302F-PL. Replacement Parts for Series 1522 Uni-Built Centrifugal Pumps
Bell & Gossett Parts List CP-302F-PL Replacement Parts for Series 1522 Uni-Built Centrifugal Pumps SERIES 1522 2 3 4 5 Standard Size Designations ITEM NO. 6 6 8 5 PUMP PART NUMBER BUILT-TO-ORDER EQUIVALENT
CM Body Assembly Service Parts List CM 93 and CM 04 Body Styles
Document Number Issue Date 12/01/93 Rev. Date 5/11/18 CM Body Assembly Service Parts List CM 93 and CM 04 Body Styles Body Style Identification Pump Material Body Style Pumps Built After 2004 Pumps Built
NPE/NPE-F REPAIR PARTS REPAIR PARTS RNPE R1
NPE/NPE-F REPAIR PARTS REPAIR PARTS RNPE R1 TABLE OF CONTENTS NPE END SUCTION NPE Product Line Numbering System...1 NPE Seal Chart (Part of Numbering System)...1 Parts List...2 Optional Components...2
Marlow Series Cast Iron Swimming Pool Pumps
INSTRUCTION MANUAL SECTION 360A AC1683 REVISION C INSTALLER: PLEASE LEAVE THIS MANUAL FOR THE OWNER'S USE. Marlow Series Cast Iron Swimming Pool Pumps 3B28EC 3B32EC PLEASE FILL IN DATA FROM YOUR PUMP NAMEPLATE
INSTRUCTION MANUAL AC2516 REVISION D INSTALLER: PLEASE LEAVE THIS MANUAL FOR THE OWNER S USE. Series 1580 In-Line Mounted Centrifugal Fire Pumps
INSTRUCTION MANUAL AC2516 REVISION D INSTALLER: PLEASE LEAVE THIS MANUAL FOR THE OWNER S USE. Series 1580 In-Line Mounted Centrifugal Fire Pumps PUMP LOCATION Locate the pump so there is sufficient room
AURORA 3500 SERIES MODEL 3550 ASME/ANSI B73.1 INDUSTRIAL PROCESS PUMPS
AURORA 3500 SERIES MODEL 3550 ASME/ANSI B73.1 INDUSTRIAL PROCESS PUMPS WWW.AURORAPUMP.COM INDUSTRIAL PROCESS PUMPS AURORA 3500 SERIES Model 3550 ASME/ANSI B73.1 Industrial Process Pumps Capacities to GPM
DI DI PUMP PARTS PRICE LIST
ITEM 1 2 2A 5050 Pump Body, 2" NPT Mech. Seal 1 40091 1 5050 Pump Body, 2" 150# RF Flg. Mech. Seal 1 40791 1 5050 Pump Body, 2" NPT, Packing 1 40088 1 5050 Pump Body, 2" 150# RF Flg., Packing 1 40793 1
EAN PUMP SERIES DL200/DL230
A Met-Pro Fluid Handling Technologies Business Combining the Resources of Dean Pump, Fybroc & Sethco DEAN PUMP SERIES DL200/DL230 Inline Centrifugal Process Pumps D A T A P A K Section DL200/DL230 SERIES
50 HZ. Ready DURABLE, LIGHTWEIGHT AND EASILY SERVICEABLE SUBERSIBLE SUBMERSIBLE PUMPS.
50 HZ Ready DURABLE, LIGHTWEIGHT AND EASILY SERVICEABLE SUBERSIBLE SUBMERSIBLE PUMPS. Multipurpose. Multiple use. Made for the duration. Whether it s for construction or industrial sites, manholes or emergency
Blockpumps. Vogel Series LSB WITH HYDRAULICS ACCORDING TO ISO 2858
Blockpumps Vogel Series LSB WITH HYDRAULICS ACCORDING TO ISO 2858 Technical Data Performance: Capacity up to 450m 3 /h (1540USgpm) Head up to 150m (280feet) Speed up to 2950/3550rpm Pump Sizes: DN 25 up
Flygt Parts List
Flygt 2870.80 Parts List Table of Contents Table of Contents Introduction... 2. Specially approved products... 2 2 Product Description...3 2. Products included... 3 2.2 The data plate...3 2.3 Product
Berkeley Cast Iron Impeller B1-1/2ZPH ELECTRIC MOTOR DRIVE. Threaded Case (NPT), Packing Construction. Table I. Table II
Cast Iron Impeller B-/ZPH Threaded Case (NPT), Packing Construction Page 50. Date March 4, 03 Supersedes 07/0/ 3 B/M HP PH RPM "U" Dim. Imp. Dia. Imp. B53759 5 3 3600 -/4" 7.94" M07666 B596 0 3 3600 -/4"
Berkeley Cast Iron Impeller B4JPBH ELECTRIC MOTOR DRIVE. Flanged Case, Packing Construction. Table I. Table II
B4JPBH Flanged Case, Packing Construction Page 0. Date March 4, 03 Supersedes 0/0/04 80B 80B 3 See Supplement B 8 4 B/M HP PH RPM "U" Dim. Imp. Dia. Imp. B588 0 3 800 -/4" 0.06" L0680 B5883 5 3 800 -/4"
PARTS MANUAL KA-3500PT PISTON TYPE PUMP INDEX
PARTS MANUAL KA-500PT PISTON TYPE PUMP INDEX - Parts Page Drawing page - Fluid End Detail page - Piston Assembly, Liner & Pony Rod Detail page - Water Manifold Assembly Detail page 5 - Oil Manifold Assembly
Discontinued Model parts availability may be limited.
COMPRESSORS CB-9E-020 1994/08 HD162A PARTS LIST Discontinued Model parts availability may be limited. Serial # ID# Gasket Sets and Special Tools Gasket Set Buna-N & Iron 792598 FKM & Iron 792596 PTFE &
PUMPS FOR INDUSTRY. The Vertical Pump Specialists CONTENTS: Introduction & User List. Product Overview. Vertical Process Pumps...
PUMPS FOR INDUSTRY CONTENTS: The Vertical Pump Specialists Introduction & User List Product Overview Vertical Process Pumps... Series 600 Vertical Sewage Pumps... Series 700 Vertical Sump Pumps... Series
TECHNICAL BROCHURE BC3WIRE-G2 R4
FEATURES 304 SS casing and end bells for corrosion resistance 304 SS casing and end bells for corrosion resistance Kingsbury type, 3 shoe, thrust bearing, see chart for ratings. Stainless steel, 17-4 PH
VSC /VSCS Pumps Technical Brochure
VSC /VSCS Pumps Technical Brochure BX-4C VSC/VSCS Construction Materials STANDARD SEAL CONFIGURATION PART NAME STANDARD CONSTRUCTION ASTM NO. Casing Cast iron A159 Class G0 Volute cover plate (Outboard)
High Temperature Chemical Process Inline Pumps
Bulletin C-1.2.21. Dean Pump Division High Temperature Chemical Process Inline Pumps Series DL Series DL High Temperature Chemical Process Inline Pumps Capacities to 6 GPM (182 m 3 /hr) Heads to feet (167
HORIZONTAL SPLIT CASE SINGLE STAGE DOUBLE SUCTION Type AE CHECKING LIST
Section Tab 1200 SINGLE STAGE DOUBLE SUCTION Section 1210 List Prices Removed 07-01-02 Use Rapid Section 1220 Data Page 0.1 & (Blank)(03-30-07) 1 & 2 (03-30-07) 2.1 & 2.2 (03-30-07) 2.21 & 2.22 (03-30-07)
Endsuction Pumps. Vogel Series LS, LC, LCP
Endsuction Pumps Vogel Series LS, LC, LCP Design LS Technical Data Performance Range: m Capacity up to 4600m 3 /h (20.250 USgpm) m Head up to 170m (560 feet) m Speed up to 1750 rpm Sizes: m DN 125 up to
barmesapumps.com WHAT IS AN ANSI PUMP
WHAT IS AN ANSI PUMP In 1977, the American National Standard Institue (ANSI) established criteria for centrifugal pumps in terms of dimension, chemical composition of the materials and safety specifications,
CURVES B-194. Series e-60 MAINTENANCE FREE IN-LINE MOUNTED CENTRIFUGAL PUMPS PERFORMANCE CURVES
CURVES B-194 MAINTENANCE FREE IN-LINE MOUNTED CENTRIFUGAL PUMPS PERFORMANCE CURVES TABLE OF CONTENTS Useful Pump Formulas..................................................................... 2 Stock Pump
A-C Fire Pump Systems FP 2.4 Page 1
ENG. DATA Page 1 February, 1996 Supersedes 5/95 issue FP 2.4 Page 2 A-C Fire Pump Systems 49-139 140-206 54-130 131-256 71-150 10WALC 10WALC 11CLC 11CLC 11CHC 500 500 750 Max Working Pressure (G) 175 psi
HD603C PARTS LIST. Gasket Set Buna-N & Iron FKM & Iron PTFE & Iron Neoprene & Iron Ethylene Propylene & Iron
COMPRESSORS CB-9E-152 2007/01 HD603C PARTS LIST Serial # ID# Gasket Sets and Special Tools Gasket Set Buna-N & Iron 794594 FKM & Iron 794592 PTFE & Iron 794593 Neoprene & Iron 794590 Ethylene Propylene
AURORA Series MODEL 3560 ASME/ANSI B73.1M INDUSTRIAL PROCESS PUMPS
AURORA 3500 Series MODEL 3560 ASME/ANSI B73.M INDUSTRIAL PROCESS PUMPS WWW.AURORAPUMP.COM AURORA 3500 Series Model 3560 ASME/ANSI B73.M Industrial Process Pumps Capacities to 7000 GPM (590 m 3 /hr) Heads
CALCULATION OF BOWL HEAD OR DISCHARGE HEAD
February, 1996 Supersedes 5/95 issue CALCULATION OF BOWL HEAD OR Pressure Gauge hd (Discharge Head) hl (LIFT) hp (Internal Pump Loss) Setting Sump Depth Pump O.A.L. Pumping Water Level hb (Bowl Head) For
Flygt Parts List
Flygt 2670.80 Parts List Table of Contents Table of Contents Introduction...2 Purpose of this manual...2 Disclaimer...2 Data for ordering spare parts...2 Specially approved products...2 Qualification
HD612C PARTS LIST. Gasket Set Buna-N & Iron FKM & Iron PTFE & Iron Neoprene & Iron Ethylene Propylene & Iron
COMPRESSORS CB-9E-192 2007/01 HD612C PARTS LIST Serial # ID# Gasket Sets and Special Tools Gasket Set Buna-N & Iron 794699 FKM & Iron 794697 PTFE & Iron 794698 Neoprene & Iron 794696 Ethylene Propylene
FI 3009, FI 3009C & FI 3009D
Replacement Parts List 304-486 FI 3009, FI 3009C & FI 3009D SUPERSEDES: June 1, 2013 EFFECTIVE: December 31, 2018 REQUIRED DESCRIPTION FI 3009 FI 3009C FI 3009D BEARING FRAME J BEARING FRAME J BEARING
The ResiBoost allows a constant set pressure regardless of demand for maximum comfort. Energy savings are the result of the precise speed control.
ResiBoost RESIBOOST IS A VARIABLE FREQUENCY DRIVE FOR CONSTANT PRESSURE SYSTEMS. RESIBOOST AUTOMATICALLY CONTROLS THE SPEED OF THE PUMP WHILE KEEPING THE PRESSURE IN THE SYSTEM CONSTANT The ResiBoost allows
855 Filtrate Pump, Close Coupled and Overhead Mounted Pumps
855 Filtrate Pump, Close Coupled and Overhead Mounted Pumps Technical Specification Pages This page left intentionally blank. 1.0 Overview. The 855 Series is Carver s offering specifically designed to
EDWARDS GEAR PUMPS REPAIR PARTS INDEX
SECION EDWARDS PAGE EDWARDS GEAR PUMPS REPAIR S INDEX READ AND UNDERSAND HE PUMP AND MOOR INSRUCIONS BEFORE AEMPING O INSALL, DISASSEMBLE OR REPAIR HE PUMP SECION EDWARDS PAGE 2 EDWARDS GEAR PUMPS MODELS,
POWERFORCE PUMP POWERFORCE PUMP POWERFORCE PUMP GLOBAL SOLUTIONS DESIGNING, MANUFACTURING AND PACKAGING FOR THE OIL & GAS INDUSTRY
POWERFORCE PUMP POWERFORCE PUMP GLOBAL SOLUTIONS DESIGNING, MANUFACTURING AND PACKAGING FOR THE OIL & GAS INDUSTRY POWERFORCE Hard Iron Centrifugal Pump Parts Item Description Qty Part Number Reference
AWWA C515 REDUCED WALL DUCTILE IRON
30" - 54" R/W VALVES AWWA C515 Resilient Wedge Gate Valves Meet or Exceed the Requirements of AWWA Standard C515 Water Working Bubble Tight Hydrostatic Shell Size Range Pressure psi Test psi Test psi AWWA
100H, 150H, 225H, 275H
TECHNICAL BROCHURE B1-275H 1H, 15H, 2H, 275H 6 HZ HIGH CAPACITY 6" SUBMERSIBLE PUMPS FOR 6" AND LARGER WELLS FEATURES Powered for Continuous Operation: All ratings are within the working limits of the
EBARA Self Priming Trash Pump. Type EFQT-EFQU
Type EFQT-EFQU Contents Section Page Model Designation 2 Features 3 Selection Chart 7 Dimension Drawings 20 Technical Data 24 Sectional View 25 1 Model Designation EFQ T 2 A MODEL TYPE EFQ self priming
Model 3550 ASME/ANSI B73.1M Industrial Process Pumps
3500 Series Model 3550 ASME/ANSI B73.1M Industrial Process Pumps The Aurora Model 3550 was designed to perform in the toughest industrial applications whether in the chemical, petro-chemical, mining, pulp
Flygt Parts List
Flygt 260.7 Parts List Table of Contents Table of Contents Introduction...2 Purpose of this manual...2 Disclaimer...2 Data for ordering spare parts...2 Specially approved products...2 Qualification of
CENTRIFUGAL PUMPS 13" CLOSE-COUPLED FEATURES
FEATURES Volute: Cast iron for heavy-duty service; back pull-out design; can be rotated for ease of installation; split volutes for reduction in radial bearing load (6 x 8-13 and 8 x 10-13) Impeller: Enclosed
3312 Model. pumping Model Model AURORA Series HORIZONTAL AND VERTICAL CLOSE-COUPLED PUMPS
3312 Model pumping 3314 Model 3311 Model AURORA 3310 Series HORIZONTAL AND VERTICAL CLOSE-COUPLED PUMPS WWW.AURORAPUMP.COM AURORA 3310 Series Horizontal and Vertical Close-Coupled Pumps Capacities to 3800
Berkeley Cast Iron Impeller B6ZPL ELECTRIC MOTOR DRIVE. Flanged Case, Packing Construction. Table I. Table II
B6ZPL Flanged Case, Packing Construction Page 350. 80B 80B 3 B509 0 -/4" 6."x8.5" M078 B5 0 3 -/4" 6."x8.5" M078 B548 5 3 -/4" 7.56"x8.56" M079 B54 0 3 -/4" 8.00"x9.00" M04348 7 80A 80A 6 Case, Volute
SPLIT CASE PUMPS REPLACEMENT PARTS GUIDE
PACO Split Case Kits are arranged so that you can replace virtually any component with minimum of effort. Here are some guidelines and suggestions: GENERAL NOTES: The pump nameplate contains all data required
Volute Casing Pumps LSN. according to iso 2828 / iso Jansen Pompentechniek T: +31(0) E:
Volute Casing Pumps LSN according to iso 2828 / iso 5199 Technical Data Performance Range: m Capacity up to 500m 3 /h (1980USgpm) m Head up to 150m (492feet) m Speed 2950/3550rpm Pump Sizes: m DN 25 up
Goulds Severe Duty Slurry Pump
Goulds 5500 Severe Duty Slurry Pump 5500 Proven leadership in mining and mineral processing Proven Leadership 100 years of slurry pumping experience. Many industry firsts including: hard metal slurry pump,
Flygt low-speed mixers. outstanding efficiency
Flygt low-speed mixers outstanding efficiency Introduction Energy-efficient mixing Advantages of Flygt low-speed mixers Rising to the mixing challenge All mixing applications require varying degrees of
EXPERT SERVICE & GENUINE PARTS. Everything it takes to keep you up and running
EXPERT SERVICE & GENUINE PARTS Everything it takes to keep you up and running Peace of Mind from the Original Service Experts At Xylem, we know what it takes to set a higher standard. All of our products
Goulds Small Capacity Double Suction Pump
Goulds 3410 Small Capacity Double Suction Pump 3410 Double Suction Pumps Designed for a Wide Range of Industrial, Municipal, Capacities to 7,000 GPM (1591 m3/h) Heads to 550 feet (168 m) Temperatures to
Truck Pumps Water XS439 XS869
Truck Pumps Water XS439 XS869 Water Truck 9" BOOK: WTP-005 DATE: Jan. 1, 2012 Features: Volute: Heavy cast iron construction. Back pullout design. Can be rotated for ease of installation. Impeller: Double