TO REPLACE A MECHANICAL SEAL Select the correct Seal Kit, which contains all gaskets and impeller hardware. Shaft sleeve inspection is suggested.
|
|
- Sharon Atkins
- 6 years ago
- Views:
Transcription
1 END SUCTION PUMPS REPLACEMENT PARTS GUIDE TYPE LC, LF, LCV This guide is valid for all Grundfos CBS products beginning with product codes 10, 11 and 20. See back cover for explanation and identification. Grundfos CBS End Suction Pumps are designed and built to provide maximum life while requiring minimum attention and service. At times, replacement parts may be required. VIRTUALLY ALL REQUIRED PARTS ARE AVAILABLE IN KIT FORM. These kits (easily selected from the charts on the following pages) have been designed to insure that any parts needed when replacing any End Suction component, are furnished when you need them, with minimum effort. Guidelines and Suggestions: The pump nameplate contains all data required in the selection and ordering of the proper replacement parts kit. The PUMP MODEL AND SERIAL NUMBER should be referenced when ever any replacement parts kit is ordered, while the pump conditions (GPM/TDH) and impeller trim are required data for the ordering of replacement impellers. NOTE: SEAL/PACKING KITS ARE ALWAYS RECOMMENDED AS SPARE PARTS TO REPLACE A MECHANICAL SEAL Select the correct Seal Kit, which contains all gaskets and impeller hardware. Shaft sleeve inspection is suggested. TO REPLACE THE PACKING Select the correct Packing Kit, which contains all gaskets, impeller hardware and lantern ring. If the packing gland is damaged it may be replaced by ordering the proper Gland Kit. A shaft sleeve or adapter shaft will probably be required. TO REPLACE THE SHAFT SLEEVES Select sleeve from sleeve chart. A Seal or Packing Kit will provide other normally needed parts. NOTE: For close-coupled units, motor frame type is required for proper sleeve replacement. Motor type is indicated by frame designation, found on motor nameplate: Gyropoise Motors - Frame XXX TG JM Motors - Frame XXX JM or JMZ CCP Motors - All Others (Fractional construction X0XXXX and X1XXXX do not require sleeves.) TO REPLACE THE BEARING FRAME Select the correct Bearing Frame assembly. TO REPLACE IMPELLER Select the correct Impeller Kit which contains all gaskets and impeller hardware. A Wear Ring Kit is highly Recommended, and a Seal or Packing Kit will probably be required. Shaft sleeve inspection is suggested. *Re-select trim for stainless steel impeller if replacing a bronze impeller Page 1 of 9
2 TO REPLACE WEAR RINGS Select the correct Wear Ring Kit. An Impeller Kit may be indicated if wear is excessive. A Seal/Packing Kit will provide all other normally replaced components. TO REPLACE BEARINGS (Frame mounted pumps only) Select the correct Bearing Frame Kit, which contains the bearings and moisture seals. TO REPLACE THE SHAFT Select the correct Shaft Kit. A Bearing Frame Kit and shaft sleeve will also be required. A Seal or Packing Kit will probably be required. TO REPLACE LOST OR DAMAGED HARDWARE Select the correct Hardware Kit. TO OVERHAUL THE PUMP Select an Impeller Kit, Wear Ring Kit, Hardware Kit, Seal or Packing Kit, and a Sleeve or Adapter Shaft. Bearing replacement may also be indicated. TO OVERHAUL THE BEARING FRAME Select a Bearing Frame Kit and a Shaft Kit. TO REPLACE SLINGER (Included in Shaft Kit) If not replacing shaft, order individually. ORDERING: After determining and selecting the required Kit(s), or for selection assistance, contact your local Grundfos CBS Sales Office, Representative or Distributor. Page 2 of 9
3 Model Pump Constr. Impeller Kit (1) Wear Ring Hardware Sleeve Seal Packing Gland No. Code Stainless* Bronze N.A. Bronze Iron Kit Kit Kit Kit X0XXXX X0XXXX X0XXXX X0XXXX X1XXXX X3XXXX X0XXXX (4) (4) X1XXXX (4) (4) X3XXXX (4) (4) X0XXXX X1XXXX X3XXXX X0XXXX X1XXXX K2323-B K2323-C X3XXXX X0XXXX X1XXXX X3XXXX X1XXXX X3XXXX X0XXXX (5) (5) X3XXXX (5) X0XXXX X3XXXX X0XXXX X3XXXX X0XXXX (6) (6) K1962-C X3XXXX (6) (6) X0XXXX X3XXXX X0XXXX #N/A X3XXXX X0XXXX X3XXXX X0XXXX X3XXXX X0XXXX X3XXXX X4XXXX X0XXXX X3XXXX X4XXXX X3XXXX X4XXXX X3XXXX X4XXXX X3XXXX X4XXXX X3XXXX X4XXXX X3XXXX X4XXXX X3XXXX X4XXXX X4-(JM MTR) X3XXXX X3XXXX X4XXXX X3XXXX (7) (7) X4XXXX (7) (7) X3XXXX X4XXXX (1), (4), (5), (6), (7), (8) See Notes on Page 5. *Re-select trim for stainless steel impeller if replacing a bronze impeller See page 6 for sleeve selection See page 7 for seal selection Page 3 of 9
4 Model Pump Constr. Impeller Kit (1) Wear Ring Hardware Sleeve Seal Packing Gland No. Code Stainless* Bronze N.A. Bronze Iron Kit Kit *(2)* Kit (3) Kit Kit X3XXXX X4XXXX X3XXXX X4XXXX X3XXXX (8) (8) X4XXXX (8) (8) X3XXXX X4XXXX X3XXXX X4XXXX X3XXXX X4XXXX X3XXXX X4XXXX X3XXXX XAXXXX X3XXXX XAXXXX X3XXXX X4XXXX B XAXXXX X3XXXX X4XXXX XAXXXX X4XXXX X4XXXX XAXXXX X5XXXX X3XXXX X4XXXX XAXXXX X4XXXX X3XXXX XAXXXX X4XXXX XAXXXX X4XXXX XAXXXX X4XXXX XAXXXX X4XXXX XAXXXX XAXXXX X5XXXX A XAXXXX X4XXXX X4XXXX XAXXXX X5XXXX X4XXXX X5XXXX X4XXXX XAXXXX X5XXXX X5XXXX X5XXXX X4XXXX XAXXXX XAXXXX X4XXXX XAXXXX X5XXXX X5XXXX X5XXXX X5XXXX X6XXXX X5XXXX X6XXXX X5XXXX X6XXXX X6XXXX X8XXXX *Re-select trim for stainless steel impeller if replacing a bronze impeller Page 4 of 9 See page 6 for sleeve selection See page 7 for seal selection
5 NOTES: (1) Specify Impeller diameter when ordering. (4) Select trim diameter for conditions from appropriate curve (5) Select trim diameter for conditions from appropriate curve (6) Select trim diameter for conditions from appropriate curve (7) Select trim diameter for conditions from appropriate curve (8) Select trim diameter for conditions from appropriate curve BEARING FRAME ASSEMBLY Const Code Steel Stainless Steel Stainless Steel Stainless Bearing Shaft Shaft Shaft Shaft Shaft Shaft Frame Greased Greased Greaseable Greaseable Oil Oil Number For Life For Life Lubed Lubed XX10XX* XX32XX* XX3PXX XX3AXX XX3LXX XX3NXX XX3MXX XX6PXX XX62XX* XX6CXX XX6KXX XX6LXX XX6NXX XX6MXX XX82XX XX8AXX XX88XX XX89XX XX90XX XX9AXX XX9PXX XX9QXX XX93XX A1b.2 Bearing Shaft Kit Shaft Kit Frame Bearing Number Number Number Kit Number (Steel) (Stainless) XX10XX XX22XX* XX3PXX XX32XX XX3AXX XX3LXX XX3NXX XX3MXX XX6PXX XX62XX XX6CXX XX6LXX XX6NXX XX6MXX XX6KXX XX82XX XX8AXX XX88XX XX89XX XX90XX XX9AXX XX9PXX XX9QXX Note: * THE 10,22, 32, 62 BEARING FRAME IS OBSOLETE. Page 5 of 9
6 SHAFT SLEEVES AND ADAPTER SHAFTS 1. Shaft Sleeves (1) See Page 1 Prior to Making Selections. A1b.2 Motor or Bearing Frame Const. Seal Packing Sleeve Part Code Material Number Fractional #10 X0XXXX X None Integral - X1XXXX X None #22 X3 X Bronze X Stainless Gypropoise (TG) #32, 3A X3 X Bronze #3L, 3N X Stainless M, 3P 03 X Bronze X Stainless X Bronze X Stainless X Bronze X Stainless JM X3 X Bronze X Stainless X Bronze X Stainless JP, CCP X3 X Bronze X Stainless X Bronze X Stainless X Bronze X Stainless JP, CCP #62, 6C, 6P X4 X Bronze #6L, 6N, 6M X Stainless X Bronze X Stainless X Bronze X Bronze JM X4 X Bronze X Stainless X Bronze X Stainless JP, CCP #62, 6C, 6P 0A X Bronze #6L, 6N, 6M X Stainless #62, 6C, 6K XA X Bronze X Stainless JM XA X Bronze X Stainless CCP #82, 88, 89, 8A X (2) Bronze X5 X Stainless X Bronze X Stainless CCP #90, 9A, 9P, 9Q X Bronze X Stainless X6 X Bronze X Stainless ADAPTER SHAFTS Motor Const. Code Packing Kit No. (1) Requires Tube of Locktite. X3 X (2) Standard single seal only. For double, JM X4 X liquid jacketed or teflon type 9 seal, use XA X the sleeve designated for packing. Page 6 of 9
7 SEAL KITS Pump Pump Std. Seal Std. Seal Viton - Viton - Viton - BUNA - BUNA - EPDM - EPDM - Model Const. BUNA - BUNA - Ni-Resist Tung. Car. Ni-Resist Cer. Seat Sil. Seat Sil. Seat Sil. Seat Code Cer. Seat Sil. Seat Seat Seat Seat Dbl. Mech Bal. Seal Std. Seal Liq. C-Code C-Code C-Code C-Code Liq. Jcktd. Std. Seal C-Code C-Code Jcktd. 1XXXXX 7XXXXX 6XXXXX 2XXXXX C-Code C-Code 8XXXXX FXXXXX C-Code 9XXXXX 3XXXXX GXXXXX X0XXXX X1XXXX K101-F X0XXXX K102-F X3XXXX K105-G X4XXXX K K104-G X3XXXX K105-G X4XXXX K106-G XAXXXX X4XXXX K K K140-F X3XXXX K107-F K107-G X4XXXX XAXXXX X5XXXX K109-F X4XXXX K K110-F XAXXXX K128-F X5XXXX K111-F X6XXXX K K112-F Page 7 of 9
8 GASKETS Pump Size (Nominal Max. Const. Seal Gasket Gasket Impeller Dia.) Code I.D. (in) P/N Description 5" X0, X1.625, Volute Gasket 7" X0, X3, X4.625, 1.25, Volute O Ring Volute Gasket 9.5" X3, X4, XA 1.25, O Ring-Backplate 9.5" X Volute Gasket Volute Gasket 12" X3, XA 1.25, O Ring-Backplate Volute Gasket 12" X Backplate Gasket Volute Gasket 15" XA O Ring-Backplate Volute Gasket 15" X5, X6 2.25, Backplate Gasket SLINGERS Const. Part Code Number X X X X4,XA X X Page 8 of 9
9 EXPLANATION OF PUMP CATALOG (Refer to Pump Nameplate) XX XXXXX Product Model Code Number XXXXXX Construction Code NOTE: This Replacement Parts Guide is valid for all Grundfos CBS products beginning with product codes 10, 11 and 20 only. Product Code 10 = Close coupled End Suction, type LC Product Code 11 = Closed Coupled Vertical Mount, type LCV Product Code 20 = Framed Mounted End Suction, type LF KIT COMPONENTS Impeller Kit: Impeller Volute Gasket Backplate Gasket Impeller Cap Screw Impeller Washer Impeller Key Impeller Nut Wear Ring Kit: Wear Rings Sleeves: (Non-Kitted) Bronze Stainless Steel Adapter Shafts: 303 Stainless Steel Adapter Shaft Key Rollpin Seal Kit: Mechanical Seal Volute Gasket Backplate Gasket Seal Cap Gasket Impeller Cap Screw Impeller Washer Impeller Key Impeller Nut Bearing Frame Assembly Bearing Frame Kit: Ball Bearings Moisture Seals Retaining Rings Shaft Kit: Shaft Slinger Keys Packing Kit: Packing Seal Volute Gasket Backplate Gasket Lantern Ring Impeller Cap Screw Impeller Washer Impeller Key Impeller Nut Gland Kit: Packing Gland Studs Nuts Bolts Washers Retaining Ring Hardware Kit: Cap Screws Gaskets: (Non-Kitted) NOTE: Kits may contain all parts listed. They are individually selected for each pump and its construction. Kits may contain gaskets wherever gasket replacement is indicated, as noted above. Should "individual" gaskets be required, see page 8. NOTE: Seal/Packing Kits are always recommended as spare parts. Page 9 of 9
This guide is valid for all Grundfos CBS products beginning with product codes 10, 11 and 20. See back cover for explanation and identification.
END SUCTION PUMPS REPLACEMENT PARTS GUIDE TYPE LC, LF, LCV This guide is valid for all Grundfos CBS products beginning with product codes 10, 11 and 20. See back cover for explanation and identification.
More informationPACO PUMPS REPLACEMENT PARTS GUIDE. A1b.2 4/06 Supercedes 8/05. Here are some guidelines and suggestions:
END SUCTION REPLACEMENT PARTS GUIDE CAT#: STOCK#: SER#: GPM: TDH: IMP. DIA: While End Suction Pumps are designed and built to provide maximum life while requiring minimum attention and service, replacement
More informationEND SUCTION PUMP WITH INTEGRATED VARIABLE FREQUENCY DRIVE REPLACEMENT PARTS GUIDE
TYPE LFE LFE END SUCTION PUMP WITH INTEGRATED VARIABLE FREQUENCY DRIVE REPLACEMENT PARTS GUIDE This guide is valid for all Grundfos CBS Inc. products beginning with product code 21. Grundfos CBS Inc. End
More informationA3b.2 October, 2013 Supercedes June, 2013 INLINE CENTRIFUGAL PUMPS REPLACEMENT PARTS GUIDE PACO TYPE VL, VLS, VLF
INLINE CENTRIFUGAL PUMPS REPLACEMENT PARTS GUIDE PACO TYPE VL, VLS, VLF This guide is valid for all PACO products beginning with product codes 16, 17 and 127 only. See back cover for explanation and identification.
More informationTYPE VSM / VSMS PARTS GUIDE
3/09 Supercedes 1/06 TYPE VSM / VSMS PARTS GUIDE VERTICAL SPACE MISER PUMPS PACO TYPE VSM, VSMS This guide is valid for all PACO products beginning with product codes 131 and 132 See back cover for explanation
More informationSPLIT-COUPLED INLINE PUMP WITH INTEGRATED VARIABLE FREQUENCY DRIVE REPLACEMENT PARTS GUIDE VLSE
SPLIT-COUPLED INLINE PUMP WITH INTEGRATED VARIABLE FREQUENCY DRIVE REPLACEMENT PARTS GUIDE VLSE This guide is valid for all Grundfos CBS Inc. products beginning with product code 28 only. While Paco In-Line
More informationPACO PUMPS. A4b.2/A5b.2 4/06 Supercedes 9/05 TYPE OL, OLN, LN (PC 37, 38, 39, 12) REPLACEMENT PARTS GUIDE
TYPE OL, OLN, LN (PC 37, 38, 39, 12) REPLACEMENT PARTS GUIDE While In-Line Pumps are designed and built to provide maximum life while requiring minimum attention and service, replacement parts may at times
More informationSPLIT CASE PUMPS REPLACEMENT PARTS GUIDE
PACO Split Case Kits are arranged so that you can replace virtually any component with minimum of effort. Here are some guidelines and suggestions: GENERAL NOTES: The pump nameplate contains all data required
More informationB/M No. B H00925 M /8-10T 3" B H00920 M /8-10T 2-1/2" Part Number. Item. No. 800B
Threaded Case (NPT), Packing Construction Page 80. Supersedes 03/0/ 87 8 B/M Mtg. Bracket Spline Ext. B00 4 H0095 M0454-3/8-0T 3" B5999 5 H0090 M07-3/8-0T -/" 7 Kit available for this model, P/N B778 for
More informationCENTRIFUGAL PUMPS CLOSE-COUPLED 9" FEATURES SPECIFICATIONS APPLICATIONS
FEATURES Volute: Heavy-duty cast iron construction; back pullout design; can be rotated for ease of installation Impeller: Enclosed, cast iron design for high efficiency; hydraulically balanced for reduced
More informationBell & Gossett Parts List CP-106F-PL. Replacement Parts for. Series 60 Maintenance Free In-Line Mounted Centrifugal Pumps
Bell & Gossett Parts List CP-106F-PL Replacement Parts for Series 60 Maintenance Free In-Line Mounted Centrifugal Pumps SERIES 60 How to use this PARTS LIST The pump nameplate identifies the pump by model
More informationBerkeley Cast Iron Impeller B1-1/2ZPH ELECTRIC MOTOR DRIVE. Threaded Case (NPT), Packing Construction. Table I. Table II
Cast Iron Impeller B-/ZPH Threaded Case (NPT), Packing Construction Page 50. Date March 4, 03 Supersedes 07/0/ 3 B/M HP PH RPM "U" Dim. Imp. Dia. Imp. B53759 5 3 3600 -/4" 7.94" M07666 B596 0 3 3600 -/4"
More informationBerkeley Cast Iron Impeller B6EXQBH SAE ENGINE MOUNT. Flanged Case, Packing Construction. Table I. Page Date March 4, 2013 Supersedes 01/01/04
BEXQBH Page. 8 83 84 ( X scale ) 3 3 5A 8 B/M Mtg. Spline B00 H05398 H053 -/-0T 3" Kit available for this model, P/N B9. Refer to Supplement-C of this section for list of components included with kit.
More informationTaco CI Series End Suction, Base Mounted Pumps
Taco CI Series End Suction, Base Mounted Pumps Taco CI Series Pumps are similar to the Bell & Gossett 1531 series of base mounted pumps. Used in commercial, industrial and institutional applications where
More informationDI DI PUMP PARTS PRICE LIST
ITEM 1 2 2A 5050 Pump Body, 2" NPT Mech. Seal 1 40091 1 5050 Pump Body, 2" 150# RF Flg. Mech. Seal 1 40791 1 5050 Pump Body, 2" NPT, Packing 1 40088 1 5050 Pump Body, 2" 150# RF Flg., Packing 1 40793 1
More informationREPAIR PARTS R36/3756 R /3756 S, M & L-Group REPAIR PARTS
REPAIR PARTS R6/756 R1 656/756 S, M & L-Group REPAIR PARTS PUMP END PARTS FOR CLOSE-COUPLED OR FRAME MOUNTED CONFIGURATION 656/756 S-Group Note: For S-Group power frame individual parts see S-Group Power
More informationPUMPS FOR INDUSTRY. The Vertical Pump Specialists CONTENTS: Introduction & User List. Product Overview. Vertical Process Pumps...
PUMPS FOR INDUSTRY CONTENTS: The Vertical Pump Specialists Introduction & User List Product Overview Vertical Process Pumps... Series 600 Vertical Sewage Pumps... Series 700 Vertical Sump Pumps... Series
More informationCLOSED COUPLED CENTRIFUGAL PUMPS
SECTION B PAGE 0 ISSUED /0 REPLACES /0 www.pumpagents.com PumpAgents.com - Click here for Pricing/Ordering SERIES: G6--/ thru G9-F 0 Third Street Piqua, Ohio 6-060 CLOSED COUPLED CENTRIFUGAL PUMPS 00RPM
More informationB/M No. Shaft Kit available for this model, P/N B Refer to Supplement-C of this section for list of components included with kit.
BJQBM Page 0. Date March 4, 03 Supersedes 0/0/04 8B 3 3C 8 B/M Mtg. Spline B0 H0598 M083 -/-0T 3" B08 H059 M083 -/-0T 3" B08 3 H059 M083 -/-0T 3" B08 4 H0595 M083 -/-0T 3" Kit available for this model,
More informationDI PUMP PARTS PRICE LIST
ITEM 1 2 2A PUMP 5040 Pump Body, 1-1/2" NPT Mech. Seal 1 40058 1 5040 Pump Body, 1-1/2" NPT, Packing 1 40057 1 5040 Pump Body, 1-1/2" 150# Flg., Mech. Seal 1 40787 1 5040 Pump Body, 1-1/2" 150# Flg., Packing
More informationBerkeley Cast Iron Impeller B4JPBH ELECTRIC MOTOR DRIVE. Flanged Case, Packing Construction. Table I. Table II
B4JPBH Flanged Case, Packing Construction Page 0. Date March 4, 03 Supersedes 0/0/04 80B 80B 3 See Supplement B 8 4 B/M HP PH RPM "U" Dim. Imp. Dia. Imp. B588 0 3 800 -/4" 0.06" L0680 B5883 5 3 800 -/4"
More informationBerkeley Cast Iron Impeller B6ZPL ELECTRIC MOTOR DRIVE. Flanged Case, Packing Construction. Table I. Table II
B6ZPL Flanged Case, Packing Construction Page 350. 80B 80B 3 B509 0 -/4" 6."x8.5" M078 B5 0 3 -/4" 6."x8.5" M078 B548 5 3 -/4" 7.56"x8.56" M079 B54 0 3 -/4" 8.00"x9.00" M04348 7 80A 80A 6 Case, Volute
More informationCLOSED COUPLED CENTRIFUGAL PUMPS
SECTION B PAGE 0 ISSUED /0 REPLACES /0 www.pumpagents.com PumpAgents.com - Click here for Pricing/Ordering SERIES: G6--/ thru G9-F 0 Third Street Piqua, Ohio 6-060 CLOSED COUPLED CENTRIFUGAL PUMPS 00RPM
More informationModels 9202C, 9203C, 9252C-C, and 9253C-C
Models 0C, 03C, C-C, and 3C-C 3 0 3 consists of () Ref. O-ring, () Ref. Mechanical Seal (Viton) and () Ref. Gasket. NOTE: When ordering parts, give quantity, part number, decription, and complete model
More informationFeatures: Applications: Irrigation. Commercial. Construction. Municipal. Mining
Frame Mount 7.5" BOOK: FMT-015 DATE: Mar. 1, 2012 Features: Volute: Ductile iron for heavy-duty service. Back pullout design. Can be rotated for ease of installation. Impeller: Enclosed design for high
More informationCENTRIFUGAL PUMPS SAE ENGINE DRIVE 10" FEATURES
FEATURES Volute: Heavy ductile iron construction; back pullout design; can be rotated for ease of installation Impeller: Ductile iron enclosed design for high efficiency; superior NPSH characteristics
More informationS Series PACER Pumps. PACER Pumps 5/91 Page 1 of 5. Dultmeier Sales for Omaha, NE or for Davenport, IA
PACER Pumps 5/91 Page 1 of 5 Item# Part No. Description Qty. 4 58-0721 NUT, BODY, Plated steel, 1/4-20 Hex... 10 58-0721 10 NUT, BODY, Stainless steel, 1/4-20 Hex... 10 6 58-0703 30 Bracket, polyester...
More informationCP-506B-PL. Series HSCS. Horizontal Split Case Pumps. Replacement Parts
Series HSCS Horizontal Split Case Pumps Replacement Parts PARTS List CP-506B-PL PARTS LIST CP-505-PL Index Description Page No. Exploded View....3 Parts List for 6x10x22, 8x12x22M, 8x12x22L, 8x12x27, and
More information855 Filtrate Pump, Close Coupled and Overhead Mounted Pumps
855 Filtrate Pump, Close Coupled and Overhead Mounted Pumps Technical Specification Pages This page left intentionally blank. 1.0 Overview. The 855 Series is Carver s offering specifically designed to
More informationbarmesapumps.com WHAT IS AN ANSI PUMP
WHAT IS AN ANSI PUMP In 1977, the American National Standard Institue (ANSI) established criteria for centrifugal pumps in terms of dimension, chemical composition of the materials and safety specifications,
More informationTECHNICAL BROCHURE B36/3742 R2 3642/3742 CLOSE-COUPLED AND FRAME-MOUNTED CENTRIFUGAL PUMPS
TECHNICAL BROCHURE B36/3742 R2 3642/3742 CLOSE-COUPLED AND FRAME-MOUNTED CENTRIFUGAL PUMPS FEATURES Compact Design: Close coupled, space saving design provides easy installation. Flexible couplings and
More information3312 Model. pumping Model Model AURORA Series HORIZONTAL AND VERTICAL CLOSE-COUPLED PUMPS
3312 Model pumping 3314 Model 3311 Model AURORA 3310 Series HORIZONTAL AND VERTICAL CLOSE-COUPLED PUMPS WWW.AURORAPUMP.COM AURORA 3310 Series Horizontal and Vertical Close-Coupled Pumps Capacities to 3800
More informationBulletin C Dean Pump Division. Heavy Duty, High Temperature Process Pumps. R4140 Telescoping Guard. R4140 C-Face Motor Support
Bulletin C 1.4.43 Dean Pump Division Heavy Duty, High Temperature Process Pumps R4140 Telescoping Guard R4140 C-Face Motor Support Dean Pump Series R Centrifugal Process Pumps Capacities to 5000 GPM (1135
More informationSERIES CS CLOSE COUPLED TURBINE PUMPS
PumpAgents.com - Click here for Pricing/Ordering SERIES CS CLOSE COUPLED TURBINE PUMPS CS- 7 RPM - 60Hz. CS - 0 RPM - 60Hz. (See Individual curves for symbol number) Symbol No. 6 7 0 6 7 MAXIMUM HEAD H.P.
More informationEUF/EUFS series. Fire Pump PSB Listed according to CP52(Singapore)
ANNEX 1: SPECIMEN OF LOGO and MARK A) SETSCO (Registered) Logo where innovation f l ow s B) SETSCO Mark for Ready-Mixed Concrete Cert No: RMC-YYYY-XXX-A C) SETSCO Mark for Fire Safety Products Fire Pump
More informationBell & Gossett Parts List CP-302F-PL. Replacement Parts for Series 1522 Uni-Built Centrifugal Pumps
Bell & Gossett Parts List CP-302F-PL Replacement Parts for Series 1522 Uni-Built Centrifugal Pumps SERIES 1522 2 3 4 5 Standard Size Designations ITEM NO. 6 6 8 5 PUMP PART NUMBER BUILT-TO-ORDER EQUIVALENT
More informationANSI Centrifugal Process Pumps. 911 Series
ANSI Centrifugal Process Pumps 9 Series WHAT IS AN ANSI PUMP In 977, the American National Standard Institue (ANSI) established criteria for centrifugal pumps in terms of dimension, chemical composition
More informationSERIES CS CLOSE COUPLED TURBINE PUMPS
PumpAgents.com - Click here for Pricing/Ordering SERIES CS CLOSE COUPLED TURBINE PUMPS CS- 7 RPM - 60Hz. CS - 0 RPM - 60Hz. (See Individual curves for symbol number) Symbol No. 6 7 8 0 6 7 8 MAXIMUM HEAD
More informationAURORA 3500 SERIES MODEL 3550 ASME/ANSI B73.1 INDUSTRIAL PROCESS PUMPS
AURORA 3500 SERIES MODEL 3550 ASME/ANSI B73.1 INDUSTRIAL PROCESS PUMPS WWW.AURORAPUMP.COM INDUSTRIAL PROCESS PUMPS AURORA 3500 SERIES Model 3550 ASME/ANSI B73.1 Industrial Process Pumps Capacities to GPM
More informationModel 3550 ASME/ANSI B73.1M Industrial Process Pumps
3500 Series Model 3550 ASME/ANSI B73.1M Industrial Process Pumps The Aurora Model 3550 was designed to perform in the toughest industrial applications whether in the chemical, petro-chemical, mining, pulp
More informationNC State University Design and Construction Guidelines Division 23 Hydronic Pumps
1.0 Purpose A. The following guidelines apply to the selection of pumps primarily for circulating water. It is the goal of NC State to purchase pumps that are selected to provide a long service life, minimal
More informationTECHNICAL BROCHURE B36/ /3742 CLOSE-COUPLED AND FRAME-MOUNTED CENTRIFUGAL PUMPS
TECHNICAL BROCHURE B36/3742 3642/3742 CLOSE-COUPLED AND FRAME-MOUNTED CENTRIFUGAL PUMPS FEATURES Compact Design: Close coupled, space saving design provides easy installation. Flexible couplings and bedplates
More informationPA SERIES END SUCTION CENTRIFUGAL PUMP SINGLE STAGE BACK PULL-OUT DIN24255 THONG FATT JAYA MACHINERY HARDWARE SDN. BHD.
END SUCTION CENTRIFUGAL PUMP SINGLE STAGE BACK PULL-OUT DIN24255 50HZ OR 60HZ PA SERIES APPLICATIONS PA Series pumps can be used for the following services in commercial, residential, agriculture, industrial,
More informationCENTRIFUGAL PUMPS 13" CLOSE-COUPLED FEATURES
FEATURES Volute: Cast iron for heavy-duty service; back pull-out design; can be rotated for ease of installation; split volutes for reduction in radial bearing load (6 x 8-13 and 8 x 10-13) Impeller: Enclosed
More informationCLOSED COUPLED CENTRIFUGAL PUMPS
40 Third Street Piqua, Ohio 4556-060 www.pumpagents.com PumpAgents.com - Click here for Pricing/Ordering SERIES G5--/4 G6--/4 SECTION B PAGE ISSUED /0 REPLACES /0 CLOSED COUPLED CENTRIFUGAL PUMPS 500RPM
More informationReplacement Parts List FI 4009 & FI 4009C. SUPERSEDES: April 28, 2016 EFFECTIVE: October 18, 2016
A Taco Family Company Replacement Parts List FI 4009 & FI 4009C 304-403 SUPERSEDES: April 28, 2016 EFFECTIVE: October 18, 2016 WHEN SELECTING AND ORDERING PARTS, ALWAYS REFER TO SERIAL ON NAMEPLATE 00
More informationSERIES: WG6-2 SELF-PRIMING CENTRIFUGAL PUMPS
420 Third Street Piqua, Ohio 436-0603 www.pumpagents.com PumpAgents.com - Click here for Pricing/Ordering SERIES: WG6-2 SECTION 4A PAGE ISSUED 2/03 REPLACES 2/0 SELF-PRIMING CENTRIFUGAL PUMPS 300RPM -
More informationTruck Pumps Water XS439 XS869
Truck Pumps Water XS439 XS869 Water Truck 9" BOOK: WTP-005 DATE: Jan. 1, 2012 Features: Volute: Heavy cast iron construction. Back pullout design. Can be rotated for ease of installation. Impeller: Double
More informationSpecifications Information and Repair Parts Manual , , , &
Please read and save this Repair Parts Manual. Read this manual and the General Operating Instructions carefully before attempting to assemble, install, operate or maintain the product described. Protect
More informationHigh Capacity Centrifugal & Sprinkler Pumps
High Capacity Centrifugal & Sprinkler Pumps FW0724 1016 Supersedes 0212 Stainless steel or cast iron construction Stainless steel impellers Discharge rotates in 90 increments on some models Pressures to
More informationCENTRIFUGAL PUMPS CLOSE-COUPLED 7.5" FEATURES
FEATURES Volute: Ductile iron for heavy-duty service; back pullout design; can be rotated for ease of installation Impeller: Enclosed design for high efficiency; configured for superior NPSH characteristics;
More informationHORIZONTAL SPLIT CASING PUMP
HORIZONTAL SPLIT CASING PUMP HORIZONTAL PUMP CONSTRUCTION MBH Horizontal Split Casing Pumps - a new concept for better performance and higher efficiencies. For greater interchangeability and ease of maintenance,
More informationNORTHWESTERN UNIVERSITY PROJECT NAME JOB # ISSUED: 03/29/2017
SECTION 23 2123 - PUMPS PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 01 Specification Sections,
More informationParts for Fig. 4565, 4566 & 4568 Industrial Section 40L Bulletin 95. Repair Parts.
www.cranepumps.com Parts for Fig. 55, 5 & 5 Item No. 1 2 * 1 19 23 * 2 32 33 * 39 2 9 70 71 * 73 101 101A 105 11 19 19A 170 199 212 21 219 22 * 21 22 2 250 25 255 25 * 257 25 20 25 27 2 270 277 25 29 29
More informationHigh Temperature Chemical Process Inline Pumps
Bulletin C-1.2.21. Dean Pump Division High Temperature Chemical Process Inline Pumps Series DL Series DL High Temperature Chemical Process Inline Pumps Capacities to 6 GPM (182 m 3 /hr) Heads to feet (167
More informationAURORA Series MODEL 3560 ASME/ANSI B73.1M INDUSTRIAL PROCESS PUMPS
AURORA 3500 Series MODEL 3560 ASME/ANSI B73.M INDUSTRIAL PROCESS PUMPS WWW.AURORAPUMP.COM AURORA 3500 Series Model 3560 ASME/ANSI B73.M Industrial Process Pumps Capacities to 7000 GPM (590 m 3 /hr) Heads
More informationHORIZONTAL SPLIT CASE SINGLE STAGE DOUBLE SUCTION Type AE CHECKING LIST
Section Tab 1200 SINGLE STAGE DOUBLE SUCTION Section 1210 List Prices Removed 07-01-02 Use Rapid Section 1220 Data Page 0.1 & (Blank)(03-30-07) 1 & 2 (03-30-07) 2.1 & 2.2 (03-30-07) 2.21 & 2.22 (03-30-07)
More informationINSTRUCTION AND REPAIR MANUAL MODELS 341A, 342A AND 344A 6
SECTION 6 ITEM 0 DATED JUNE 1998 SUPERSEDES ITEMS 1, 2, DATED MARCH 1992 INSTRUCTION AND REPAIR MANUAL MODELS 1A, 2A AND A 6 NOTE This repair manual is applicable to pump Models 1A, 2A and A. All photos
More informationMaterial Specifications
5.2012.12.b 6200 Series Specifications The Flomore 6200 Series Pump line consists of a series of basic pump options all developed from a modular power unit. All units are pneumatically driven positive
More informationAURORA MODEL 410 SERIES ENGINEERING DATA MECHANICAL SEALS AND PACKING
AURORA MODEL 410 SERIES MECHANICAL SEALS AND PACKING Section 410 Page 71 Supersedes Section 410 Page 71 1 PACKING WITH OPTIONAL LANTERN RING SINGLE INSIDE UNBALANCED 3 SINGLE INSIDE BALANCED TAP OPTIONALLY
More informationHIGH CAPACITY CENTRIFUGAL & SPRINKLER PUMPS
HIGH CAPACITY CENTRIFUGAL & SPRINKLER PUMPS FW0724 0707 Supersedes 1005 Straight Centrifugal Pumps Electric Motors Heavy Duty Straight Centrifugal Pumps High Head Straight Centrifugal Pumps Stainless Steel
More informationCENTRIFUGAL PUMPS 7.5" FRAME MOUNT SERIES FEATURES
FEATURES Volute: Ductile iron volute for heavy-duty service; back pullout design; can be rotated for ease of installation Impeller: Enclosed design for high efficiency; configured for superior NPSH characteristics;
More informationData sheet. Page: 1 / 5. ETL GGSAV11D BKSBIE3 Inline pump. Operating data. Design
Data sheet Page: 1 / 5 Operating data Requested flow rate Operating data determined for maximum inlet pressure Requested developed head 15.00 m Pumped medium Ambient air temperature 20.0 C Fluid temperature
More informationKP-C Series. Close Coupled End Suction Centrifugal Pumps. Installation, Operation and Maintenance
KP-C Series Close Coupled End Suction Centrifugal Pumps Installation, Operation and Maintenance PUMP MODEL NOMENCLATURE KP - 8 x 6 x 16 - E C - AI - BCM Pump Series Suction Pipe Size (in) Discharge Pipe
More informationMarlow Series Prime Line
REPAIR PARTS RPRIMELINE Marlow Series Prime Line SELF-PRIMING CENTRIFUGAL PUMPS REPAIR PARTS Prime Line M2P M4P Pumps 27 50 49 27 54 1 8 10 6 17 4 67 5 24 37 63 53 51 2 7 46 2 PAGE 2 Prime Line 2" Pump
More informationGH General Horizontal, Close Coupled and Frame Mounted Pumps
GH General Horizontal, Close Coupled and Frame Mounted Pumps Technical Specification Pages This page left intentionally blank. 1.0 Overview. The GH Series is Carver s horizontal, end suction pump for handling
More informationSeries e-1510 REPLACEMENT PARTS FOR STANDARD DESIGN PUMPS PARTS LIST CP-208G-PL
Series e-1510 REPLACEMENT PARTS FOR STANDARD DESIGN PUMPS PARTS LIST CP-208G-PL PARTS LIST CP-208G-PL SERIES e-1510 Index Nameplate Data.................................................. Exploded Views...................................................
More informationBasic Hydraulic Features. Basic Mechanical Features
APRIL 2006 1.0 Overview The ETA is designed for flow rates that fall beyond the range of most end suction pumps. Performance extends to 9,500 GPM, 440 feet of head, and 88% efficiency. This range is covered
More information3800 Series. Single Stage End Suction Pumps. Capacities to 4200 G.P.M. (954 m 3 /hr) Heads to 520 Feet (180 Meters) Temperatures to 300 F (149 C)
3800 Series Single Stage End Suction Pumps Capacities to 200 G.P.M. (95 m 3 /hr) Heads to 520 Feet (180 Meters) Temperatures to 300 F (19 C) MODEL 380 Aurora 3800 Pump Setting New Standards of Efficiency
More informationDrive Motor Type 3 (115/230V, 1 Phase TEFC) Motor Type 4 (230/460V, 3 Phase TEFC) Options Description Price Adders
PMU (Pump & Motor Unit) Prices 1000 4000 3000 Drive Motor Type 3 (115/230V, 1 Phase TEFC) Motor Type 4 (230/460V, 3 Phase TEFC) N HP 1725 rpm Consult Factory N/A L HP 1725 rpm Consult Factory Consult Factory
More informationEnd Suction Centrifugal
M o d e l s 3 U / 3 U B End Suction Centrifugal Operating Instructions, Installation & Maintenance Manual Certified to NSF/ANSI 6, ANNEX G * NSF/ANSI 6 Annex G listed models: 3U EBARA International Corporation
More informationProduct Numbering System Typical Specifi cations, Models 4AC, 4AE, 6AC, 6AE, 8AC Pump Assembly, Types AC & AE
Index Sheet ITEM S Bulletin Product Numbering System... 1 Typical Specifi cations, Models 4AC, 4AE, 6AC, 6AE, 8AC... 2 Pump Assembly, Types AC & AE... 3-4 Dimensions, Types AC & AE... 5-8 Selection Curves,
More informationStory of 3 R s. Pum pen Intel 1 ligen z
Story of 3 R s Pum pen Intel 1 ligen z Various Standard for End Suction Pumps Pum pen Intel 2 ligen z Comparison of ET & NL Options ET NL MoC Beyond Cat A & B Yes No MoC Variants within Cat A & B Yes No
More information6200 Series. Specifications. Fluid End Power End Models 6211, 6212, 6221, & 6222 Models 6241 & 6242 Part Material Part Material Part Material
5.2018.12.i 6200 Series Specifications The Flomore 6200 Series Pump line consists of a series of basic pump options all developed from a modular power unit. All units are pneumatically driven positive
More information3340 Series Single Stage End Suction Pumps
3340 Series Single Stage End Suction Pumps Bulletin 3340/Rev. A Model 3344 Aurora 3340 Pump Setting New Standards of Efficiency Liquid handling requirements are much more involved than they were five years
More informationGoulds Small Capacity Double Suction Pump
Goulds 3410 Small Capacity Double Suction Pump 3410 Double Suction Pumps Designed for a Wide Range of Industrial, Municipal, Capacities to 7,000 GPM (1591 m3/h) Heads to 550 feet (168 m) Temperatures to
More informationITT. Goulds Pumps. G&L Series SSH S & M-Group 316 Stainless Steel End Suction Pumps. Engineered for life. Commercial Water.
ITT Goulds Pumps G&L Series SSH S & M-Group 316 Stainless Steel End Suction Pumps www.goulds.com Engineered for life A Full Range of Product Features Superior Materials of Construction: AISI Type 316L
More informationINSTRUCTION MANUAL AND PARTS LIST FOR A3D SERIES PUMPS
TM INSTRUCTION MANUAL AND PARTS LIST FOR A3D SERIES PUMPS WARNING This Instruction Manual and General Instructions Manual SRM00046, should be read thoroughly prior to pump installation, operation or maintenance.
More informationCALCULATION OF BOWL HEAD OR DISCHARGE HEAD
February, 1996 Supersedes 5/95 issue CALCULATION OF BOWL HEAD OR Pressure Gauge hd (Discharge Head) hl (LIFT) hp (Internal Pump Loss) Setting Sump Depth Pump O.A.L. Pumping Water Level hb (Bowl Head) For
More informationSeries e-60. In-Line Mounted Centrifugal Pumps Maintenance Free Replacement Parts PARTS LIST CP-107-PL
Series e-60 In-Line Mounted Centrifugal Pumps Maintenance Free Replacement Parts PARTS LIST CP-107-PL Index How to Use This Parts List... 3 Exploded View Series e-60 Maintenance Free Pump... 4 Standard
More informationA-C Fire Pump Systems FP 2.4 Page 1
ENG. DATA Page 1 February, 1996 Supersedes 5/95 issue FP 2.4 Page 2 A-C Fire Pump Systems 49-139 140-206 54-130 131-256 71-150 10WALC 10WALC 11CLC 11CLC 11CHC 500 500 750 Max Working Pressure (G) 175 psi
More informationCentrifugal End Suction Fire Pumps
Centrifugal End Suction Fire Pumps 1 Centrifugal End Suction Fire Pumps Product Overview American-Marsh Model FP-REF End Suction pumps are used in a variety of fire protection services every day. These
More informationPROCESS PUMPS MODEL V200 ANSI B73.2
EAGLE PROCESS PUMPS V200 ANSI B73.2 POWER END Shaft Diameters Bearings Stuffing Box PUMP END Maximum Diameter Solids Minimum Casing Thickness Casing Corrosion Allowance Working Pressure Test Pressure
More informationPWA ANSI / ASME B73.1 PROCESS PUMP
PWA ANSI / ASME B73.1 PROCESS PUMP COMPETITIVE ADVANTAGES Carbon Steel vs. Ductile Iron n High strength, impact resistant Carbon Steel liquid ends for improved durability and pressure containment at no
More informationHigh Temperature Air-Cooled Hot Oil Pumps
Bulletin C 1.4.42 Dean Pump Division High Temperature Air-Cooled Hot Oil Pumps No Water Cooling Required RA296 RA3146 RA3186 RA296 The smaller, foot mounted economy version of the air-cooled RA series
More informationData sheet. Page: 1 / 5 ETN GG A 11GA201502B. Operating data. Design. Requested developed head m. Efficiency 74.
Data sheet Page: 1 / 5 Operating data Requested flow rate 160.00 m³/h Actual flow rate 159.85 m³/h Operating data determined for maximum inlet pressure Actual developed head 20.96 m Requested developed
More informationGoulds GIS Series. ISO Frame & Stub Shaft Pumps. Goulds Pumps
Goulds GIS Series ISO Frame & Stub Shaft Pumps Goulds Pumps ISO End Suction Centrifugal Pump - Technical Sales Data The ITT Goulds brand is renowned for manufacturing the highest quality pumping equipment
More informationGoulds GIS Series. ISO Frame & Stub Shaft Pumps. Goulds Pumps
Goulds GIS Series ISO Frame & Stub Shaft Pumps Goulds Pumps ISO End Suction Centrifugal Pump - Technical Sales Data The ITT Goulds brand is renowned for manufacturing the highest quality pumping equipment
More informationSuction Diffusers. Applications PROTECTION PUMP. Pressures to 790 PSIG Temperatures to 800ºF FEATURES MATERIALS END CONNECTIONS SIZE RANGES RATINGS
Applications Process Industry Metals and Mining Power Industry Water and Waste Chemical Industry Pulp and Paper Oil and Gas Suction Diffusers Pressures to 790 PSIG Temperatures to 800ºF FEATURES Filtration
More informationContents. Identification
Contents Identification Type key Product data Introduction Applications Features and benefits Performance range pole pole Construction Sectional drawing Construction features Test pressure Operating conditions
More informationCOMPRESSORS 09/97 CB-5C-050. Suggested Spare Parts for LB601 and LB601A Compressors: Qty./ Unit
09/97 CB-5C-050 Suggested Spare Parts for LB601 and LB601A Compressors: Part # Description Qty./ Unit Comm. Qty. 794099 Gasket Set - Buna-N, Aluminum T 1 1 1 794259 Suction Valve Sub-Assembly T 2 2 794279
More informationD51 D61 D71 D91 Series
MTH PUMPS D51 D61 D71 D91 Series Page D-1 Capacities to 24 GPM Heads to 36 Feet Horizontal Close Coupled Close-coupled centrifugal pumps from MTH provide economical performance up to 24 GPM applications
More informationTHELCO REPLACEMENT PARTS FOR WORTHINGTON PUMPS PARTS CATALOG
ENGINEERING A SIGN OF SERVICE FABRICATING THELCO REPLACEMENT PARTS FOR WORTHINGTON PUMPS PARTS CATALOG SEPTEMBER 2018 ISSUE #22 Version 1.0 September 2018 Pricing THELCO CORPORATION 2390 W. DARTMOUTH AVE.
More information3 DIAPHRAGM PUMP 1:1 RATIO (METALLIC)
OPERATOR S MANUAL INCLUDING: OPERATION, INSTALLATION & MAINTENANCE 3 DIAPHRAGM PUMP 1:1 RATIO (METALLIC) PD30X-X-X-C PE30X-X-X-C RELEASED: 2-9-05 REVISED: 3-5-07 (REV. 04) READ THIS MANUAL CAREFULLY BEFORE
More informationReplacement Parts List FI 4007 & FI 4007D. SUPERSEDES: NEW EFFECTIVE: December 31, 2018
Replacement Parts List 304-572 FI 4007 & FI 4007D SUPERSEDES: NEW EFFECTIVE: December 31, 2018 WHEN SELECTING AND ORDERING PARTS, ALWAYS REFER TO SERIAL ON NAMEPLATE FI 4007 BEARING FRAME J FI 4007D BEARING
More informationSERIES 4300 TC/TSC/TCZ MOTORS
FILE : 6043.137 DATE: July 7, 2010 SUPERSEDES: 6043.137 DATE: June 24, 2010 PARTS LIST SERIES 4300 DESIGN TC/TSC/TCZ MOTORS VERTICAL IN-LINE SPLIT COUPLER "DBL" DESIGNATION - GROUPS 25 TO 51 TS and TSC
More informationElite. KSB Australia Pty Ltd. Centrifugal Pump
Type Series Booklet Elite Centrifugal Pump Application The Ajax Elite centrifugal pump is suitable for handling water and similar liquids mainly used in the following applications. -Water Supply -Air conditioning
More informationLB361B PARTS LIST COMPRESSORS CB-5E /06. Bulletins Needed For Complete Parts List. Gasket Set, Repair Kits and Special Tools
COMPRESSORS CB-5E-031 2011/06 LB361B PARTS LIST Serial # ID# Gasket Set, Repair Kits and Special Tools Gasket Set Buna-N & Aluminum 793099 Top End Repair Kit 793229 Includes Piston Rings & Expanders, Packing
More informationabcdef EJseries Self-Priming Centrifugal Pumps where innovation flows SNG
abcdef SNG 9 where innovation flows Self-Priming Centrifugal Pumps EJseries www.euroflopumps.com Coding System EJseries Series EJS = Shaft Sewage Bare Pumps EJT = Large Flow Trash Pumps EJU = High Head
More informationEN. 850 Filtrate Pumps. Technical Specification Pages
850 17.01.EN 850 Filtrate Pumps Technical Specification Pages 850 Series Filtrate Pump 850 17.01.EN This page left intentionally blank. 1.0 Overview. The 850 is Carver s filtrate pump line designed for
More information