3340 Series Single Stage End Suction Pumps
|
|
- Johnathan Jordan
- 5 years ago
- Views:
Transcription
1 3340 Series Single Stage End Suction Pumps Bulletin 3340/Rev. A Model 3344
2 Aurora 3340 Pump Setting New Standards of Efficiency Liquid handling requirements are much more involved than they were five years ago. The variety of liquids being handled has increased along with temperatures and pressures. Today s installations demand quiet, smooth running pumps with long life. Aurora Pump s 80 years of experience with design, sales and manufacturing of centrifugal pumps has lead to the 3340 Series. These modern pumps with a clean, straightforward design were developed with maximum interchangeability in mind. Aurora s highly reliable 3340 pumps offer an economical solution to your liquid handling problems A 9C 9 9B Standard: 3341 Standard JM motor Cast Iron, Bronze Fitted Construction Formed Steel base ouble Volute on 4 discharge and larger to reduce bearing loads Suction splitter on some 3 and all 4 suction and larger to eliminate pre-rotation Gauge taps on suction and discharge standard on flanged models Shaft sleeve to protect JM motor shaft Optional sleeve materials Casing feet for easy back pullout Optional mechanical seal materials NPT Pipe Plug 5. Casing bolts or studs 6. Casing 8. Casing gasket 9. Impeller Bolt 9A. Impeller washer 9B. Impeller gasket 9C. Impeller bolt gasket 10. Shaft sleeve gasket 11. Impeller 12. Impeller Key 25. Shaft Sleeve 27. Seal 32. Motor Bolts 33. Nameplate screw 34. Nameplate 35. Seal Plate / Motor Bracket 43. Grease Fitting page 2
3 Aurora 3340 Pump A 9C 9 9B Standard 3344 Regreaseable bearings Standard JM motor Shaft Extension Coupling guard Cast Iron, Bronze Fitted Construction Formed steel bases ouble Volute on 4 discharge and larger to reduce bearing loads. Suction Splitter on some 3 and all 4 suction and larger to eliminate pre-rotation. Heavy duty power frame with regreaseable bearings for long life. Gauge taps on suction discharge standard on flanged models. Shaft sleeve to protect high strength JM design shaft. Optional L shaft materials. Casing feet for easy back pull out. Optional seal materials NPT Pipe Plug 5. Casing Bolts 6. Casing 8. Casing Gasket 9. Impeller Bolt 9A. Impeller Washer 9B. Imp. Washer Gasket 9C. Impeller Bolt Gasket 10. Shaft Sleeve Gasket 11. Impeller 12. Impeller Key 25. Shaft Sleeve 27. Seal 28. Bearing Plate Bolts 32. Power Frame Bolts 33. Nameplate Screw 34. Nameplate 35. Seal Plate 42. Power Frame Key 43. Grease Fitting 49. Bearing Cap 52. Bearing Snap Ring 53. Inboard Bearing 54. Outboard Bearing 55. Shaft 57. Power Frame 62. Foot Support Bolt 63. Foot Support Washer 64. Support Foot page 3
4 3341 Product Offering AG APPRO. F ISCHARGE A VIEW A-A LESS CASING F F BA A B P1 B1 P2 B2 HH BOLT SIE G EE AA EE E A E PUMP F F F F F SIE ISCH SUCT P1 P2 B1 B2 G HH EE AA JM JM JM JM TC 1.25 x 1.5 x N/A N/A N/A (NPT) (178) (127) (83) (114) (35) (41) (60) (67) (16) (11) (83) (203) (108) (108) 1.5 x 2 x N/A N/A N/A (NPT) (178) (152) (79) (117) (37) (40) (62) (65) (16) (11) (83) (203) (116) (116) 1.5x2x NA NA NA (NPT) (254) (197) (70) (146) (49) (56) (73) (95) (17) (11) (116) (279) (116) (116) 2 x 2.5 x N/A N/A (178) (165) (89) (121) (40) (37) (65) (62) (16) (11) (83) (203) (113) (113) (140) 2x2.5x NA (203) (178) (102) (149) (40) (71) (60) (092) (17) (011) (116) (279) (113) (113) (143) (143) 2.5 x 3 x N/A (178) (152) (108) (119) (41) (35) (67) (60) (16) (11) (83) (203) (113) (113) (140) (140) 2.5x3x (203) (171) (102) (152) (41) (70) (62) (90) (17) (11) (116) (279) (121) (121) (135) (135) (252) 3 x 4 x N/A (178) (152) (105) (127) (43) (33) (68) (59) (16) (11) (83) (203) (116) (116) (125) (125) 3x4x (203) (191) (121) (156) (46) (65) (68) (84) (19) (11) (116) (279) (116) (116) (129) (129) (235) 4x5x NA (203) (191) (125) (146) (57) (54) (78) (75) (17) (11) (116) (279) (118) (118) (140) (140) 4x5x (254) (203) (127) (178) (48) (64) (68) (84) (19) (11) (116) (279) (121) (121) (130) (130) (236) 5x6x (254) (216) (148) (159) (71) (40) (92) (60) (18) (11) (116) (279) (132) (132) (154) (154) (243) 5x6x NA (279) (254) (152) (191) (56) (71) (81) (81) (22) (13) (178) (406) (116) (116) (138) (138) 6x8x NA NA NA (279) (267) (178) (210) (114) (114) (140) (140) (16) (267) (584) (137) (137) Only available in 215 OP motor frame for 15 HP max Only available in 326 OP motor frame for 60 HP max 1. All dimensions in inches (mm). 2. imensions may vary ± Not for construction purposes unless certified. 4. Conduit box is shown in approximate location. imensions are not specified as they may vary with each motor manufacturer. 5. All motors are JM motor frames. page 4
5 3341 Product Offering AG APPRO. F ISCHARGE A VIEW A-A LESS CASING F F BA A B P1 B1 P2 B2 HH BOLT SIE G EE AA EE E A E JM MOTOR FRAME FRAME AG APPRO. A B E F H BA (251) (178) (152) (89) (70) (51) (9) (57) (279) (178) (152) (89) (70) (64) (9) (57) (279) (229) (165) (114) (95) (57) (10) (70) (305) (229) (191) (114) (95) (70 (10) (70) (356) (267) (191) (133) (108) (70) (10) (89) (381) (267) (229) (133) (108) (89) (10) (89) (445) (318) (2.73) (159) (127) (105) (13) (108) (483) (318) (318) (159) (127) (127) (13) (108) (483) (356) (318) (178) (140) (121) (13) (121) (533) (356) (356) (178) (140) (140) (13) (121) (559) (406) (356) (203) (159) (133) (17) (133) (584) (406) (394) (203) (159) (152) (17) (133) (610) (457) (387) (229) (178) (143) (17) (149) (610) (457) (413) (229) (178) (156) (17) (149) (692) (508) (413) (254) (203) (156) (21) (168) (730) (508) (451) (254) (203) (175) (21) (168) 1. All dimensions in inches (mm). 2. imensions may vary ± 1/4. 3. Not for construction purposes unless certified. page page 5
6 ISCHARGE KEWA V U (66) (102) (12) LONG SLOTS A AC P1 B1 P2 B2 H BOLT SIE G E E A PUMP SIE ISCH SUCT P1 P2 B1 B2 G H E A AC A 1.25 x 1.5 x 7S (NPT) (178) (127) (83) (114) (35) (41) (60) (67) (16) (11) (83) (203) (229) (251) (368) 1.5 x 2 x 7S (NPT) (178) (152) (79) (117) (37) (40) (62) (65) (16) (11) (83) (203) (229) (251) (367) 1.5 x 2 x 11S (NPT) (203) (229) (79) (146) (37) (75) (57) (95) (17) (11) (116) (279) (229) (251) (367) 1.5 x 2 x 11L (NPT) (203) (229) (79) (146) (37) (75) (57) (95) (17) (11) (116) (279) (305) (329) (445) 1.5 x 2 x 12S (NPT) (254) (197) (70) (146) (49) (56) (73) (95) (17) (11) (116) (279) (229) (251) (370) 2 x 2.5 x 7S (178) (165) (89) (121) (40) (37) (65) (62) (16) (11) (83) (203) (229) (251) (379) 2 x 2.5 x 9.5S (203) (178) (102) (149) (40) (71) (60) (92) (17) (11) (116) (279) (229) (251) (392) 2 x 2.5 x 9.5L (203) (178) (102) (149) (40) (71) (60) (92) (17) (11) (116) (279) (305) (330) (472) 2 x 3 x 11S (254) (203) (140) (165) (57) (70) (82) (96) (22) (13) (178) (406) (194) (216) (413) 2 x 3 x 11L (254) (203) (140) (165) (57) (70) (82) (96) (22) (13) (178) (406) (257) (298) (495) 2 x 3 x 13.5L (254) (229) (140) (184) (51) (76) (76) (102) (22) (13) (178) (406) (257) (308) (498) 2.5 x 3 x 7S (178) (152) (108) (120) (41) (35) (67) (60) (16) (11) (83) (203) (229) (251) (400) 2.5 x 3 x 9.5S (203) (171) (102) (152) (41) (70) (62) (90) (17) (11) (116) (279) (229) (251) (394) 2.5 x 3 x 9.5L (203) (171) (102) (152) (41) (70) (62) (90) (17) (11) (116) (279) (305) (330) (473) 2.5 x 3 x 13.5L (254) (229) (152) (203) (51) (76) (76) (102) (22) (13) (178) (406) (257) (308) (514) 3 x 4 x 7S (178) (152) (105) (127) (43) (33) (68) (59) (16) (11) (83) (203) (229) (251) (398) 3 x 4 x 7L (178) (152) (105) (127) (43) (33) (68) (59) (16) (11) (83) (203) (305) (330) (478) 3 x 4 x 9.5S (203) (191) (121) (156) (46) (65) (68) (84) (19) (11) (116) (279) (229) (251) (414) 3 x 4 x 9.5L (203) (191) (121) (156) (46) (65) (68) (84) (19) (11) (116) (279) (305) (330) (497) 3 x 4 x 11S (254) (241) (140) (187) (62) (65) (87) (91) (22) (13) (178) (406) (200) (216) (416) 3 x 4 x 11L (254) (241) (140) (187) (62) (65) (87) (91) (22) (13) (178) (406) (257) (295) (497) 3 x 4 x 13.5L (254) (241) (143) (203) (54) (73) (80) (98) (22) (13) (178) (406) (257) (306) (503) 1. All dimensions in inches (mm). 2. imensions may vary ± 1/4. 3. Not for construction purposes unless certified. 4. S-denotes small power frame; L-denotes large power frame; L-denotes extra large power frame. Available in 125# suction /250# discharge. POWER FRAME U V KE Small SQ. x 1.25 LNG (41) (6) x (30) Large SQ. x 1.25 LNG (32) (44) (6) x (30) Extra Large SQ. x 2.63 LNG (48) (89) (13) x (67) page 6
7 ISCHARGE KEWA V U (66) (102) (12) LONG SLOTS A AC P1 B1 P2 B2 H BOLT SIE G E E A PUMP SIE ISCH SUCT P1 P2 B1 B2 G H E A AC A 4 x 5 x 7S (203) (191) (125) (146) (57) (54) (78) (75) (17) (11) (116) (279) (229) (251) (433) 4 x 5 x 7L (203) (191) (125) (146) (57) (54) (78) (75) (17) (11) (116) (279) (305) (330) (513) 4 x 5 x 9.5S (254) (203) (127) (178) (48) (64) (68) (84) (19) (11) (116) (279) (229) (251) (425) 4 x 5 x 9.5L (254) (203) (127) (178) (48) (64) (68) (84) (19) (11) (116) (279) (305) (330) (505) 4 x 5 x 11S (254) (248) (141) (184) (61) (75) (91) (91) (22) (13) (178) (406) (194) (216) (419) 4 x 5 x 11L (254) (248) (141) (184) (61) (75) (91) (91) (22) (13) (178) (406) (257) (298) (500) 4 x 5 x 13.5L (279) (254) (152) (218) (57) (70) (83) (95) (22) (13) (178) (406) (257) (292) (502) 5 x 6 x 7S (254) (216) (148) (159) (71) (40) (92) (60) (18) (11) (116) (279) (229) (251) (470) 5 x 6 x 7L (254) (216) (148) (159) (71) (40) (92) (60) (18) (11) (116) (279) (305) (330) (549) 5 x 6 x 9.5S (279) (254) (152) (191) (59) (71) (81) (81) (22) (13) (178) (406) (229) (251) (459) 5 x 6 x 9.5L (279) (254) (152) (191) (59) (71) (81) (81) (22) (13) (178) (406) (305) (330) (538) 5 x 6 x 11L (279) (267) (138) (202) (66) (61) (87) (91) (22) (13) (178) (406) (257) (283) (487) 5 x 6 x 13.5L (305) (330) (152) (229) (106) (122) (132) (148) (16) (267) (584) (213) (257) (516) 5 x 6 x 13.5L (305) (330) (152) (229) (106) (122) (132) (148) (16) (267) (584) (305) (365) (624) 6 x 8 x 9.5L (279) (267) (178) (210) (79) (48) (105) (73) (22) (13) (178) (406) (305) (330) (587) 6 x 8 x 11L (305) (279) (156) (215) (117) (111) (143) (137) (16) (267) (584) (213) (267) (540) 6 x 8 x 13.5L (321) (340) (165) (237) (114) (114) (140) (140) (16) (267) (584) (305) (357) (637) 8 x 10 x 13.5L (381) (356) (203) (279) (114) (114) (140) (140) (16) (267) (584) (305) (329) (672) POWER FRAME U V KE Small SQ. x 1.25 LNG (41) (6) x (30) Large SQ. x 1.25 LNG (32) (44) (6) x (30) Extra Large SQ. x 2.63 LNG (48) (89) (13) x (67) 1. All dimensions in inches (mm). 2. imensions may vary ± 1/4. 3. Not for construction purposes unless certified. 4. S-denotes small power frame; L-denotes large power frame; L-denotes extra large power frame. Available in 125# suction /250# discharge. page 7
8 ISCHARGE HT C APPRO. HL HG HA 1. imensions are approximate. 2. imensions are in inches (mm) and may vary ± 1/4 (6). 3. Conduit box is shown in aproximate position. imensions are not HH IA. HOLES specified as they vary with each motor manufacturer. 4. Not for construction purposes unless certified. 5. -for 1750 RPM applications; -for 3550 RPM applications; for 1750 and 3500 RPM applications. HB 6. HT is based on Aurora standard coupling. If optional coupling is specified, HT may vary from.25 to 1.5. SMALL LARGE PUMP MOTOR C POWER POWER BASE SIE ISCHG HL FRAME APPRO. FRAME FRAME NO x 1.5 x (305) 1 (NPT) (178) (127) (83) (114) (368) 143T 12 (305) 1 145T 13 (330) 1 182T 13 (330) 1 184T 14 (356) 2 213T 16 (406) 2 215T 18 (457) x 2 x (305) 1 (NPT) (178) (152) (79) (117) (368) 143T 13 (330) 1 145T 13 (330) 1 182T 13 (330) 1 184T 14 (356) 2 213T 16 (406) 2 215T 17 (432) x 2 x T 13 (330) 1 (NPT) (203) (229) (79) (146) (367) (64) 145T 13 (330) 1 182T 13 (330) 1 184T 14 (356) 2 213T 16 (406) 2 215T 17 (432) T 16 (406) 3 (445) 215T 17 (432) 3 254T 21 (533) 4 256T 23 (584) 4 284TS 22 (559) 5 284T 24 (610) 5 286TS 24 (610) 5 286T 25 (635) 5 324TS 25 (635) 6 324T 26 (660) x 2 x T 13 (330) 2 (NPT) (254) (197) (70) (179) (370) (76) 145T 13 (330) 2 182T 13 (330) 2 184T 14 (356) 2 213T 16 (406) 3 215T 18 (457) 3 254T 21 (533) 4 256T 23 (584) 4 2 x 2.5 x (305) 1 (178) (165) (83) (121) (379) 143T 13 (330) 1 145T 13 (330) 1 182T 13 (330) 1 184T 14 (356) 2 213T 16 (406) 2 215T 17 (432) 3 254T 21 (533) 4 page 8
9 ISCHARGE HT C APPRO. HL HG HA HH IA. HOLES HB SMALL LARGE PUMP MOTOR C POWER POWER BASE SIE ISCHG HL FRAME APPRO. FRAME FRAME NO. 2 x 2.5 x T 13 (330) 1 (203) (178) (102) (149) (392) 182T 13 (330) 1 184T 14 (356) 2 213T 16 (406) 2 215T 17 (432) T 17 (432) 3 (471) 254T 21 (533) 4 256T 23 (584) 4 284TS 22 (559) 5 284T 24 (610) 5 286TS 24 (610) 5 286T 25 (635) 5 324TS 25 (635) 6 324T 26 (660) 6 326TS 26 (660) 6 326T 28 (711) 6 364TS 27 (686) 6 364T 29 (737) 6 2 x 3 x T 13 (330) 10 (254) (203) (140) (165) (413) 184T 14 (356) T 16 (406) T 18 (457) T 21 (533) TS 24 (610) 6 (495) 286T 24 (610) 6 324TS 25 (635) 6 324T 25 (635) 6 326TS 26 (660) 6 326T 26 (660) 6 364TS 28 (711) 6 364T 27 (686) 7 365TS 29 (737) 7 365T 30 (762) 7 2 x 3 x T 16 (406) 10 (254) (229) (140) (184) (498) 215T 18 (457) T 21 (533) 6 256T 23 (584) 6 284TS 22 (559) 6 284T 24 (610) x 3 x (305) 2 (178) (152) (108) (119) (400) 143T 12 (305) 2 145T 13 (330) 2 182T 13 (330) 2 184T 14 (356) 2 184T 14 (356) 2 213T 16 (406) 3 215T 18 (457) 3 254T 21(533) 4 1. imensions are approximate. 2. imensions are in inches (mm) and may vary ± 1/4 (6). 3. Conduit box is shown in aproximate position. imensions are not specified as they vary with each motor manufacturer. 4. Not for construction purposes unless certified. 5. -for 1750 RPM applications; -for 3550 RPM applications; for 1750 and 3500 RPM applications. page 9 Available in 125# suction /250# discharge. 6. HT is based on Aurora standard coupling. If optional coupling is specified, HT may vary from.25 to 1.5.
10 ISCHARGE HT C APPRO. HL HG HA HH IA. HOLES HB SMALL LARGE PUMP MOTOR C POWER POWER BASE SIE ISCHG HL FRAME APPRO. FRAME FRAME NO. 2.5 x 3 x T 13 (330) 2 (203) (171) (102) (152) (394) 184T 14 (356) 2 213T 16 (406) 3 215T 18 (457) T 21 (533) 4 (473) 256T 23 (584) 4 284TS 22 (559) 5 286TS 24 (610) 5 324TS 25 (635) 6 326TS 26 (660) 6 9 (229) 364TS 27 (686) 6 2.5x3x T 13 (330) 10 (254) (229) (152) (203) (514) 184T 14 (356) T 16 (406) T 18 (457) T 21 (533) 6 256T 23 (584) 6 284TS 24 (610) 6 284T 24 (610) 6 3 x 4 x T 12 (305) 2 (178) (152) (105) (127) (398) 145T 13 (330) 2 182T 13 (330) 2 184T 14 (356) 2 213T 16 (406) 3 215T 18 (457) T 16 (406) 4 (478) 215T 18 (457) 4 256T 23 (584) 4 284TS 22 (559) 5 286TS 24 (610) 5 254T 21 (533) 4 3 x 4 x T 13 (330) 2 (203) (191) (121) (156) (414) 182T 13 (330) 2 184T 14 (356) 2 213T 16 (406) 3 215T 18 (457) 3 254T 21 (533) T 23 (584) 4 (497) 284TS 22 (559) 5 286TS 24 (610) 5 324TS 25 (635) 6 326TS 26 (660) 6 Available in 125# suction /250# discharge. 1. imensions are approximate. 2. imensions are in inches (mm) and may vary ± 1/4 (6). 3. Conduit box is shown in aproximate position. imensions are not specified as they vary with each motor manufacturer. 4. Not for construction purposes unless certified. 5. -for 1750 RPM applications; -for 3550 RPM applications; -for 1750 and 3500 RPM applications. 6. HT is based on Aurora standard coupling. If optional coupling is specified, HT may vary from.25 to 1.5. page 10
11 ISCHARGE HT C APPRO. HL HG HA HH IA. HOLES HB SMALL LARGE -LARGE PUMP MOTOR C POWER POWER POWER BASE SIE ISCHG HL FRAME APPRO. FRAME FRAME FRAME NO. 3 x 4 x T 16 (406) 10 (254) (241) (140) (187) (416) 215T 18 (457) T 21 (533) T 23 (584) 6 (497) 284TS 22 (559) 6 284T 23 (584) 6 286TS 24 (610) 6 286T 25 (635) 6 324TS 25 (635) 6 324T 26 (660) 6 326TS 26 (660) 6 326T 28 (711) 6 364TS 27 (686) 6 364T 29 (737) 7 365TS 28 (711) 7 365T 30 (762) 7 404TS 31 (787) 7 404T 33 (839) 11 3 x 4 x T 16 (406) 10 (254) (203) (143) (203) (503) 215T 18 (457) T 21 (533) 6 256T 23 (584) 6 284TS 22 (559) 6 284T 24 (610) 6 286TS 24 (610) 6 286T 25 (635) 6 4 x 5 x T 13 (330) 2 (254) (203) (127) (178) (433) 182T 13 (330) 2 184T 14 (356) 2 213T 16 (406) 3 215T 17 (432) T 17 (432) 4 (513) 254T 21 (533) 4 256T 23 (584) 4 284TS 22 (559) 5 284T 24 (610) 5 286TS 24 (610) 5 286T 25 (635) 5 324TS 25 (635) 6 324T 26 (660) 6 326TS 26 (660) 6 326T 28 (711) 6 Use L power frame with impeller diameters larger than 12.5 (318) 1. imensions are approximate. 2. imensions are in inches (mm) and may vary ± 1/4 (6). 3. Conduit box is shown in aproximate position. imensions are not specified as they vary with each motor manufacturer. 4. Not for construction purposes unless certified. 5. -for 1750 RPM applications; -for 3550 RPM applications; -for 1750 and 3500 RPM applications. 6. HT is based on Aurora standard coupling. If optional coupling is specified, HT may vary from.25 to 1.5. Available in 125# suction/250# discharge. page 11
12 ISCHARGE HT C APPRO. HL HG HA HH IA. HOLES HB SMALL LARGE -LARGE PUMP MOTOR C POWER POWER POWER BASE SIE ISCHG HL FRAME APPRO. FRAME FRAME FRAME NO. 4 x 5 x T 16 (406) 3 (254) (203) (127) (178) (425) 215T 17 (432) 3 254T 21 (533) T 23 (584) 4 (505) 284TS 22 (559) 5 284T 24 (610) 5 286TS 24 (610) 5 286T 25 (635) 5 324TS 25 (635) 6 324T 26 (660) 6 326TS 26 (660) 6 326T 28 (711) 6 364TS 27 (686) 6 364T 29 (737) 7 365TS 28 (711) 7 365T 30 (762) 7 404TS 30 (762) 7 404T 33 (839) 11 4 x 5 x T 17 (432) 10 (254) (152) (141) (184) (419) 254T 21 (533) T 23 (584) 6 (500) 284TS 22 (559) 6 284T 24 (610) 6 286TS 24 (610) 6 286T 25 (635) 6 324TS 25 (635) 6 324T 26 (660) 6 326TS 26 (660) 6 326T 28 (711) 6 364TS 27 (686) 6 364T 29 (737) 7 365TS 28 (711) 7 365T 30 (762) 7 404TS 30 (762) 7 404T 33 (839) 11 4 x 5 x T 16 (406) 10 (279) (254) (152) (218) (502) 215T 18 (457) T 21 (533) 6 256T 23 (584) 6 284TS 22 (559) 6 284T 24 (610) 6 286TS 24 (610) 6 286T 25 (635) 6 Available in 125# suction /250# discharge. 1. imensions are approximate. 2. imensions are in inches (mm) and may vary ± 1/4 (6). 3. Conduit box is shown in aproximate position. imensions are not specified as they vary with each motor manufacturer. 4. Not for construction purposes unless certified. 5. -for 1750 RPM applications; -for 3550 RPM applications; -for 1750 and 3500 RPM applications. 6. HT is based on Aurora standard coupling. If optional coupling is specified, HT may vary from.25 to 1.5 page 12
13 ISCHARGE HT C APPRO. HL HG HA HH IA. HOLES HB SMALL LARGE -LARGE PUMP MOTOR C POWER POWER POWER BASE SIE ISCHG HL FRAME APPRO. FRAME FRAME FRAME NO. 5 x 6 x T 13 (330) 3 (254) (216) (148) (159) (470) 184T 14 (356) 3 213T 16 (406) 3 215T 18 (457) T 23 (584) 5 (549) 284TS 22 (559) 5 284T 24 (610) 5 286TS 24 (610) 6 286T 25 (635) 6 324TS 25 (635) 7 324T 26 (660) 7 326TS 26 (660) 7 326T 28 (711) 7 364TS 27 (686) 7 364T 29 (737) 7 5 x 6 x T 16 (406) 10 (279) (254) (152) (191) (459) 215T 17 (432) T 21 (533) T 23 (584) 6 (538) 284TS 22 (559) 6 284T 24 (610) 6 5 x 6 x T 21 (533) 6 (279) (267) (138) (202) (487) 256T 23 (584) 6 284TS 22 (559) 6 284T 24 (610) 6 286TS 24 (610) 6 286T 25 (635) 6 324TS 25 (635) 6 324T 26 (660) 6 5 x 6 x T 21 (533) 8 (305) (330) (152) (229) (516) (51) 256T 23 (584) 8 284TS 22 (559) 8 284T 24 (610) 8 286TS 24 (610) 8 286T 25 (635) 8 324TS 25 (635) 8 324T 26 (660) 8 326TS 26 (660) 8 326T 28 (711) 8 364TS 27 (686) 8 364T 29 (737) TS 26 (660) 8 (624) 326T 28 (711) 8 364TS 27 (686) T 29 (737) TS 28 (711) T 30 (762) 12 Available in 125# suction /250# discharge. 1. imensions are approximate. 2. imensions are in inches (mm) and may vary ± 1/4 (6). 3. Conduit box is shown in aproximate position. imensions are not specified as they vary with each motor manufacturer. 4. Not for construction purposes unless certified. 5. -for 1750 RPM applications; -for 3550 RPM applications; -for 1750 and 3500 RPM applications. 6. HT is based on Aurora standard coupling. If optional coupling is specified, HT may vary from.25 to 1.5 page 13
14 ISCHARGE HT C APPRO. HL HA HG 1. imensions are approximate. 2. imensions are in inches (mm) and may vary ± 1/4 (6). 3. Conduit box is shown in aproximate position. imensions HH IA. HOLES are not specified as they vary with each motor manufacturer. 4. Not for construction purposes unless certified. 5. -for 1750 RPM applications; -for 3550 RPM HB applications; -for 1750 and 3500 RPM applications. 6. HT is based on Aurora standard coupling. If optional coupling is specified, HT may vary from.25 to 1.5 SMALL LARGE -LARGE PUMP MOTOR C POWER POWER POWER BASE SIE ISCHG HL FRAME APPRO. FRAME FRAME FRAME NO. 6 x 8 x T 21 (533) 6 (279) (267) (178) (210) (587) 256T 23 (584) 6 284TS 22 (559) 6 284T 24 (610) 6 286TS 24 (610) 7 286T 25 (635) 7 324TS 25 (635) 7 324T 26 (660) 7 326TS 26 (660) 7 326T 28 (711) 7 6 x 8 x TS 22 (559) 8 (305) (279) (156) (215) (540) 284T 24 (610) 8 286TS 24 (610) 8 286T 25 (635) 8 324TS 25 (635) 8 324T 26 (660) 8 326TS 26 (660) 8 326T 28 (711) 8 364TS 27 (686) 8 364T 29 (737) 8 6 x 8 x TS 24 (610) 8 (321) (340) (165) (237) (637) 286T 25 (635) 8 324TS 25 (635) 8 324T 26 (660) 8 326TS 26 (660) 8 326T 28 (711) 8 364TS 27 (686) T 29 (737) TS 28 (711) T 30 (762) TS 30 (762) T 33 (839) TS 31 (787) T 34 (864) 12 8x10x TS 22 (559) 8 (381) (356) (203) (279) (672) 284T 24 (610) 8 286TS 24 (610) 8 286T 25 (635) 8 324TS 25 (635) 8 324T 26 (660) 8 326TS 26 (660) 8 326T 28 (711) 8 364TS 27 (686) T 29 (737) TS 28 (711) T 30 (762) TS 30 (762) T 33 (839) TS 31 (787) T 34 (864) TS 34 (864) T 38 (965) 13 Available in 125# suction /250# discharge. page 14
15 ISCHARGE HT C APPRO. HL HG HA HH IA. HOLES HB BASE SIE HA HB HG HH (305) (762) (76) (16) (305) (864) (76) (16) (305) (965) (76) (16) (330) (1143) (102) (19) (381) (1219) (86) (19) (457) (1270) (102) (19) (559) (1372) (102) (19) (660) (1372) (102) (19) (381) (1067) (10) (19) (457) (1067) (102) (19) (559) (1524) (102) (19) (660) (1524) (114) (19) x (660) (1676) (114) (19) MOTOR HORSEPOWER AN FRAME ESIGNATION HORSEPOWER 3600 RPM 1800 RPM RATING OP TEFC OP TEFC 1/ / T 143T 1-1/2 143T 143T 143T 145T 2 145T 145T 145T 145T 3 145T 182T 182T 182T 5 182T 184T 184T 184T 7-1/2 184T 213T 213T 213T T 215T 215T 215T T 254T 254T 254T T 256T 256T 256T T 284TS 284T 284T TS 286TS 286T 286T TS 324TS 324T 324T TS 326TS 326T 326T TS 364TS 364TS 364TS TS 365TS 365TS 365TS TS 405TS 404TS 405TS TS - 405TS - POWER FRAME U V KE Small SQ. x 1.25 LNG (41) (6) x (30) Large SQ. x 1.25 LNG (32) (44) (6) x (30) Extra Large SQ. x 2.63 LNG (48) (89) (13) x (67) 1. imensions are approximate. 2. imensions are in inches (mm) and may vary ± 1/4 (6). 3. Conduit box is shown in aproximate position. imensions are not specified as they vary with each motor manufacturer. 4. Not for construction purposes unless certified. page page 15
16 Engineering Specifications Flexible-Close Coupled Pumps The contractor shall furnish (and install as shown on the plans) Aurora model (3341 horizontal close coupled) (3344 horizontal flexible coupled) back pull out centrifugal pump size x x of bronze fitted construction. Each pump shall have a capacity of GPM at ft of total head, with a temperature of ÅãF, specific gravity, Each pump is to be furnished with a mechanical seal with all metals parts to be 303 stainless steel with Buna-N elastomers, ceramic seat, and carbon washer. The unit must be equipped with (bronze) (stainless steel) key-locked shaft sleeve that extends the length of the seal plate. The pump shaft extension shall be gasket sealed from the pumped liquid. The Pump may have an optional Bronze case-wearing ring. Impellers to be bronze cast, dynamically balanced, and key locked to the shaft. Flexible Coupled-Frame Mounted (3344) Pump and motor are to be mounted on a common (fabricated steel) (fabricated steel drip rim) base plate. The shaft is to be steel, installed in a cast iron power frame. Pumps shall have a shaft design of.002 deflection at the seal face with the pump running under maximum load condition. Grease ball bearings, have a 3-year minimum life (AFBMA B10) under the maximum condition of load. The pump shall be flexible coupled to a standard horizontal NEMA HP phase Hertz volts RPM (open drip proof) (totally enclosed fan cooled) (explosion-proof) motor. Alignment shall be checked in accordance with the standards of the Hydraulic Institute after installation and there shall be no strain transmitted to be pumps. Close-coupled (3341) Each pump is to be close coupled to a HI-NEMA- JM Series HP. Phase Hertz volts RPM (open drip proof) (totally enclosed fan cooled) (explosion-proof) motor. All 3341 models shall have motors supplied with feet. Material of Construction Pump Part Casing Impeller Seal Plate/Motor Bracket Shaft Sleeve Power Frame (3344) (Small, Large or -Large) Mechanical Seal Bronze Fitted Cast Iron ASTM A48 Bronze ASTM B584 Cast Iron ASTM A48 Steel AISI 1018 Bronze ASTM B62 Cast Iron ASTM A stainless steel metal parts, Buna-N elastomer parts, Ceramic seat and carbon washer esign etails Power Frame Area escription Small Large -Large Rotation from driver end CW CW CW iameter at impeller iameter at shaft sleeve Pump Shaft iameter between bearings iameter at coupling end Coupling key square Max. deflection at seal face Bearing (inboard radial) Bearing (outboard thrust) Ball Bearings Bearing centers Bearing type Ball Ball Ball Min B 10 bearing life 3 years 3 years 3 years under maximum load Sleeve Outside diameter of sleeve NOTE: Aurora Pump reserves the right to make revisions to its products and their specifications, and to this bulletin and related information, without notice. our Authorized Local istributor HRAULIC 19 INSTITUTE 17 ISO 9001 REGISTERE QUALIT SSTEM AP-3340 (7.05) MARKETING & SALES: 800 AIRPORT ROA NORTH AURORA, ILLINOIS U.S.A PHONE: (630) U.S.A./CANAA FA: (630) WORLWIE FA: (630) WEB: aurora_info@pentairpump.com AURORA MFG. PLANT: 800 AIRPORT ROA NORTH AURORA, ILLINOIS U.S.A SALES OFFICES IN ALL MAJOR CITIES AN COUNTRIES Refer to Pumps in yellow pages of your phone directory for your local istributor.
3800 Series. Single Stage End Suction Pumps. Capacities to 4200 G.P.M. (954 m 3 /hr) Heads to 520 Feet (180 Meters) Temperatures to 300 F (149 C)
3800 Series Single Stage End Suction Pumps Capacities to 200 G.P.M. (95 m 3 /hr) Heads to 520 Feet (180 Meters) Temperatures to 300 F (19 C) MODEL 380 Aurora 3800 Pump Setting New Standards of Efficiency
More information3312 Model. pumping Model Model AURORA Series HORIZONTAL AND VERTICAL CLOSE-COUPLED PUMPS
3312 Model pumping 3314 Model 3311 Model AURORA 3310 Series HORIZONTAL AND VERTICAL CLOSE-COUPLED PUMPS WWW.AURORAPUMP.COM AURORA 3310 Series Horizontal and Vertical Close-Coupled Pumps Capacities to 3800
More informationModel 133 Models 134 & 135 AURORA 130 SERIES SINGLE STAGE TURBINE TYPE PUMPS
Model Models 4 & AURORA 0 SERIES SINGLE STAGE TURBINE TYPE PUMPS WWW.AURORAPUMP.COM AURORA 0 SERIES Single Stage Turbine Type Pumps Capacities to 0 G.P.M. Heads to 700 Ft. Temperatures to F A Pioneer in
More informationD51 D61 D71 D91 Series
MTH PUMPS D51 D61 D71 D91 Series Page D-1 Capacities to 24 GPM Heads to 36 Feet Horizontal Close Coupled Close-coupled centrifugal pumps from MTH provide economical performance up to 24 GPM applications
More informationBasic Hydraulic Features. Basic Mechanical Features
APRIL 2006 1.0 Overview The ETA is designed for flow rates that fall beyond the range of most end suction pumps. Performance extends to 9,500 GPM, 440 feet of head, and 88% efficiency. This range is covered
More informationOne & Two Stage Turbine Type Pumps
0A Series APO One & Two Stage Turbine Type Pumps apacities to 0 GPM Heads to 700 Feet Temperatures to 7 F Standard Bronze fitted construction Hydraulically balanced bronze impeller Right- or left-hand
More informationM50 L50 Series Multistage Regenerative Turbine Pumps
Page M- MTH PUMPS M L Series Multistage Regenerative Turbine Pumps Capacities to 4 GPM Heads to Feet Single or Multi-stage Units (up to stages) Vertical Close Coupled Horizontal Close Coupled Horizontal
More informationGH General Horizontal, Close Coupled and Frame Mounted Pumps
GH General Horizontal, Close Coupled and Frame Mounted Pumps Technical Specification Pages This page left intentionally blank. 1.0 Overview. The GH Series is Carver s horizontal, end suction pump for handling
More informationTECHNICAL BROCHURE B36/ /3742 CLOSE-COUPLED AND FRAME-MOUNTED CENTRIFUGAL PUMPS
TECHNICAL BROCHURE B36/3742 3642/3742 CLOSE-COUPLED AND FRAME-MOUNTED CENTRIFUGAL PUMPS FEATURES Compact Design: Close coupled, space saving design provides easy installation. Flexible couplings and bedplates
More informationAURORA 3500 SERIES MODEL 3550 ASME/ANSI B73.1 INDUSTRIAL PROCESS PUMPS
AURORA 3500 SERIES MODEL 3550 ASME/ANSI B73.1 INDUSTRIAL PROCESS PUMPS WWW.AURORAPUMP.COM INDUSTRIAL PROCESS PUMPS AURORA 3500 SERIES Model 3550 ASME/ANSI B73.1 Industrial Process Pumps Capacities to GPM
More informationCLOSED COUPLED CENTRIFUGAL PUMPS
SECTION B PAGE 0 ISSUED /0 REPLACES /0 www.pumpagents.com PumpAgents.com - Click here for Pricing/Ordering SERIES: G6--/ thru G9-F 0 Third Street Piqua, Ohio 6-060 CLOSED COUPLED CENTRIFUGAL PUMPS 00RPM
More informationRegenerative Turbine Pumps
Bulletin T June 04 T E Series Regenerative Turbine Pumps Capacities to 40 GPM Heads to 700 Feet Temperatures to 00 F MTH PUMPS MTH T E Series Close-coupled and pedestal mounted regenerative turbine pumps
More informationTECHNICAL BROCHURE B36/3742 R2 3642/3742 CLOSE-COUPLED AND FRAME-MOUNTED CENTRIFUGAL PUMPS
TECHNICAL BROCHURE B36/3742 R2 3642/3742 CLOSE-COUPLED AND FRAME-MOUNTED CENTRIFUGAL PUMPS FEATURES Compact Design: Close coupled, space saving design provides easy installation. Flexible couplings and
More informationCLOSED COUPLED CENTRIFUGAL PUMPS
SECTION B PAGE 0 ISSUED /0 REPLACES /0 www.pumpagents.com PumpAgents.com - Click here for Pricing/Ordering SERIES: G6--/ thru G9-F 0 Third Street Piqua, Ohio 6-060 CLOSED COUPLED CENTRIFUGAL PUMPS 00RPM
More informationSERIES: WG6-2 SELF-PRIMING CENTRIFUGAL PUMPS
420 Third Street Piqua, Ohio 436-0603 www.pumpagents.com PumpAgents.com - Click here for Pricing/Ordering SERIES: WG6-2 SECTION 4A PAGE ISSUED 2/03 REPLACES 2/0 SELF-PRIMING CENTRIFUGAL PUMPS 300RPM -
More informationIndex - Section 14 End Suction Pump Semi-Open Impeller
Index - Section End Suction Pump Semi-Open Impeller ITEM S Product Numbering System...1 Typical Architects / Engineers Specifi cations - Series 4000...2 Seal Application...3-4 Technical Charts...5-6 Pump
More informationBulletin D51 September D51 D61 D71 D91 Series. Centrifugal Pumps. Capacities to 240 GPM Heads to 360 Feet MTH PUMPS
ulletin D1 September 006 D1 D61 D71 D91 Series Centrifugal Pumps Capacities to 0 GPM Heads to 60 eet MTH PUMPS Casing Standard casing construction of all units is ASTM A8 Class 0 cast iron. All bronze
More informationVSC /VSCS Pumps Technical Brochure
VSC /VSCS Pumps Technical Brochure BX-4C VSC/VSCS Construction Materials STANDARD SEAL CONFIGURATION PART NAME STANDARD CONSTRUCTION ASTM NO. Casing Cast iron A159 Class G0 Volute cover plate (Outboard)
More informationCentrifugal End Suction Fire Pumps
Centrifugal End Suction Fire Pumps 1 Centrifugal End Suction Fire Pumps Product Overview American-Marsh Model FP-REF End Suction pumps are used in a variety of fire protection services every day. These
More informationITT. Goulds Pumps. G&L Series SSH S & M-Group 316 Stainless Steel End Suction Pumps. Engineered for life. Commercial Water.
ITT Goulds Pumps G&L Series SSH S & M-Group 316 Stainless Steel End Suction Pumps www.goulds.com Engineered for life A Full Range of Product Features Superior Materials of Construction: AISI Type 316L
More informationSUGGESTED SPECIFICATIONS Pump Frames NS3 thru OMC5
SOLIDS-HANDLING WASTEWATER PUMPS Pump Frames NS3 thru OMC5 GENERAL Furnish and install Vertical Closed-Shaft Wet-Pit Pumping Units complete with all accessories and appurtenances as shown in the plans
More informationAURORA Series MODEL 3560 ASME/ANSI B73.1M INDUSTRIAL PROCESS PUMPS
AURORA 3500 Series MODEL 3560 ASME/ANSI B73.M INDUSTRIAL PROCESS PUMPS WWW.AURORAPUMP.COM AURORA 3500 Series Model 3560 ASME/ANSI B73.M Industrial Process Pumps Capacities to 7000 GPM (590 m 3 /hr) Heads
More informationEN. 850 Filtrate Pumps. Technical Specification Pages
850 17.01.EN 850 Filtrate Pumps Technical Specification Pages 850 Series Filtrate Pump 850 17.01.EN This page left intentionally blank. 1.0 Overview. The 850 is Carver s filtrate pump line designed for
More informationRegenerative Turbine Pumps
Bulletin M M Series Regenerative Turbine Pumps Capacities to 8 GPM Heads to Feet MTH M Series Vertical base mount and horizontal pedestal mounted multi-stage regenerative turbine pumps represent the most
More informationRegenerative Turbine Pumps
Bulletin E4 November 009 E4 T4 Series Regenerative Turbine Pumps Capacities to GPM Heads to 600 Feet Temperatures to 00 F MTH PUMPS MTH E4 T4 Series Close-coupled and pedestal mounted regenerative turbine
More informationBulletin BX-512H. Bell & Gossett. Series HSC-S Pumps Technical Bulletin. Bell & Gossett. Part of the. Equipment Selection Programs
Bulletin BX-1H Bell & Gossett Series HSC-S Pumps Technical Bulletin Part of the Bell & Gossett Equipment Selection Programs TABLE OF CONTENTS Useful Pump Formulas...............................................
More informationHigh Temperature Air-Cooled Hot Oil Pumps
Bulletin C 1.4.42 Dean Pump Division High Temperature Air-Cooled Hot Oil Pumps No Water Cooling Required RA3 RA2 DEAN PUMP SERIES RA FAN COOLED HIGH TEMPERATURE HOT OIL PUMPS No Liquid Cooling Required
More informationHigh Temperature Air-Cooled Hot Oil Pumps
Bulletin C 1.4.42 Dean Pump Division High Temperature Air-Cooled Hot Oil Pumps No Water Cooling Required RA296 RA3146 RA3186 RA296 The smaller, foot mounted economy version of the air-cooled RA series
More informationBulletin BX-420C Bell & Gossett. VSC /VSCS Pumps Technical Bulletin. Bell & Gossett. Part of the. Equipment Selection Program
Bulletin BX-4C Bell & Gossett VSC /VSCS Pumps Technical Bulletin Part of the Bell & Gossett Equipment Selection Program VSC/VSCS Construction Materials STANDARD SEAL CONFIGURATION PART NAME STANDARD CONSTRUCTION
More informationRegenerative Turbine Pumps
Bulletin E4 July E4/T4 Series Regenerative Turbine Pumps Capacities to GPM Heads to 6 Feet Temperatures to F MTH E4/T4 Series Close-coupled and pedestal mounted regenerative turbine pumps represent the
More information390 Series Multi-Stage Vertical In-Line Centrifugal Pumps
Bulletin 390 /Rev. B 390 Series Multi-Stage Vertical In-Line Centrifugal Pumps Capacities to 400 G.P.M. (91 M 3 /HR) Heads to 800 Feet (243 Meters) Temperatures to 250 F (120 C) motralec 4 rue Lavoisier.
More informationSeries: GA6-1½, GA6-2, GA7-1¼, GA7-1½
Series: GA6-1½, GA6-2, GA7-1¼, GA7-1½ 1750 RPM - 60Hz. CAPACITIES TO 160 GPM (10 LPS) HEADS TO 57 FEET (17.3 M) 1450 RPM - 50Hz. CAPACITIES TO 140 GPM (8.8 LPS) HEADS TO 40 FEET (12 M) Individual performance
More informationModel 3550 ASME/ANSI B73.1M Industrial Process Pumps
3500 Series Model 3550 ASME/ANSI B73.1M Industrial Process Pumps The Aurora Model 3550 was designed to perform in the toughest industrial applications whether in the chemical, petro-chemical, mining, pulp
More informationTri-Clover SP328 Centrifugal Pump
Tri-Clover SP328 Centrifugal Pump Mfg: Tri Clover Stock No. OIP025. Model: SP328ME-00-S Serial No. E3152 Tri-Clover SP328 Centrifugal Pump. Model SP328ME-00-S. S/N E3151. Capacity: up to 380 gpm. Impeller:
More informationSeries HSC-S Pumps Technical Brochure
Series HSCS Pumps Technical Brochure BX512L Table of Contents Useful Pump Formulas 2 60 Cycle Performance Curves Series HSCS 3 50 Cycle Performance Curves Series HSCS 4 Series HSCS Materials of Construction
More informationProduct Numbering System Typical Specifi cations, Models 4AC, 4AE, 6AC, 6AE, 8AC Pump Assembly, Types AC & AE
Index Sheet ITEM S Bulletin Product Numbering System... 1 Typical Specifi cations, Models 4AC, 4AE, 6AC, 6AE, 8AC... 2 Pump Assembly, Types AC & AE... 3-4 Dimensions, Types AC & AE... 5-8 Selection Curves,
More informationGoulds Small Capacity Double Suction Pump
Goulds 3410 Small Capacity Double Suction Pump 3410 Double Suction Pumps Designed for a Wide Range of Industrial, Municipal, Capacities to 7,000 GPM (1591 m3/h) Heads to 550 feet (168 m) Temperatures to
More informationG&L Pumps. TECHNICAL Brochure BAC8100. Series A-C 8100 SPLIT CASE PUMPS
TECHNICAL Brochure BAC8 Series A-C 8 SPLIT CASE PUMPS TABLE OF CONTENTS Useful Pump Formulas 2 Performance Curves 3-5 Materials of Construction (Standard) 6 Materials of Construction (Optional) 7 Pump
More information4500C Series Vortex Pumps
Section 009 Page 003 4500C Series Vortex Pumps Table of Contents 4500C Performance 2" x 2" - 4523C, Multiple Speed... 004 3" x 3" - 4523C, Multiple Speed... 004 4" x 4" - 4522C, Multiple Speed... 005 4"
More informationNC State University Design and Construction Guidelines Division 23 Hydronic Pumps
1.0 Purpose A. The following guidelines apply to the selection of pumps primarily for circulating water. It is the goal of NC State to purchase pumps that are selected to provide a long service life, minimal
More informationBulletin C Dean Pump Division. Heavy Duty, High Temperature Process Pumps. R4140 Telescoping Guard. R4140 C-Face Motor Support
Bulletin C 1.4.43 Dean Pump Division Heavy Duty, High Temperature Process Pumps R4140 Telescoping Guard R4140 C-Face Motor Support Dean Pump Series R Centrifugal Process Pumps Capacities to 5000 GPM (1135
More informationbarmesapumps.com WHAT IS AN ANSI PUMP
WHAT IS AN ANSI PUMP In 1977, the American National Standard Institue (ANSI) established criteria for centrifugal pumps in terms of dimension, chemical composition of the materials and safety specifications,
More informationCENTRIFUGAL PUMPS CLOSE-COUPLED 9" FEATURES SPECIFICATIONS APPLICATIONS
FEATURES Volute: Heavy-duty cast iron construction; back pullout design; can be rotated for ease of installation Impeller: Enclosed, cast iron design for high efficiency; hydraulically balanced for reduced
More informationSeries: GA6-1½, GA6-2, GA7-1¼, GA7-1½
Series: GA6-1½, GA6-2, Features FOUR POSITION CASING Discharge can be located in any of four positions. Casing is close grain iron of 30,000 psi minimum tensile strength. Back pull-out design eliminates
More informationRegenerative Turbine Pumps
Bulletin 40 October 008 40 40 80 80 Series Regenerative Turbine Pumps Capacities to 60 GPM Heads to 800 Feet MTH PUMPS 40 40 80 80 Series regenerative turbine pumps represent the most economical, high
More informationCE Close-Coupled End Suction Pumps. Leading The Flow. TACO.
CE Close-Coupled End Suction Pumps Leading The Flow. TACO. Quiet, dependable power and proven performance. CE Series Pumps meet the latest standards for hydraulic performance and dimensional characteristics.
More informationHigh Temperature Chemical Process Inline Pumps
Bulletin C-1.2.21. Dean Pump Division High Temperature Chemical Process Inline Pumps Series DL Series DL High Temperature Chemical Process Inline Pumps Capacities to 6 GPM (182 m 3 /hr) Heads to feet (167
More informationITT. Goulds Pumps G&L Series NPO. Engineered for life. Commercial Water. Open Impeller All Stainless Steel End Suction Pumps.
ITT Goulds Pumps G&L Series NPO Open Impeller All Stainless Steel End Suction Pumps www.goulds.com Engineered for life A Full Range of Product Features NPO Product Line Numbering System Superior Materials
More informationSUGGESTED SPECIFICATIONS
PART 1 - GENERAL 1.01 SCOPE A. Pumps to be supplied under this specification shall be of a severe duty, recessed cupped impeller design suitable for use in (SLUDGE, GRIT, ETC. APPLICATIONS) with a 20 year
More informationFE Frame-Mounted End Suction Pumps. Leading The Flow. TACO.
FE Frame-Mounted End Suction Pumps Leading The Flow. TACO. Quiet, dependable power and proven performance. FE Series Pumps meet the latest standards for hydraulic performance and dimensional characteristics.
More informationPUMPS FOR INDUSTRY. The Vertical Pump Specialists CONTENTS: Introduction & User List. Product Overview. Vertical Process Pumps...
PUMPS FOR INDUSTRY CONTENTS: The Vertical Pump Specialists Introduction & User List Product Overview Vertical Process Pumps... Series 600 Vertical Sewage Pumps... Series 700 Vertical Sump Pumps... Series
More informationJOCKEY PUMPS MTH Tool Co. Series T41, T51, 150, 160 Regenerative Turbine Vane Type. TYPICAL SPECIFICATION MTH Tool Co. Series T41, T51 Pumps
Peerless Pump Company Indianapolis, IN 46206-7026 JOCKEY PUMPS MTH Tool Co. Series T41, T51, 150, 160 Regenerative Turbine Vane Type SECTION 1720 Page 1 August 10, 1992 TYPICAL SPECIFICATION MTH Tool Co.
More information855 Filtrate Pump, Close Coupled and Overhead Mounted Pumps
855 Filtrate Pump, Close Coupled and Overhead Mounted Pumps Technical Specification Pages This page left intentionally blank. 1.0 Overview. The 855 Series is Carver s offering specifically designed to
More informationCLOSED COUPLED CENTRIFUGAL PUMPS
40 Third Street Piqua, Ohio 4556-060 www.pumpagents.com PumpAgents.com - Click here for Pricing/Ordering SERIES G5--/4 G6--/4 SECTION B PAGE ISSUED /0 REPLACES /0 CLOSED COUPLED CENTRIFUGAL PUMPS 500RPM
More informationRS Multi-Stage, Ring Section Pumps
RS Multi-Stage, Ring Section Pumps Technical Specification Pages This page left intentionally blank. 1.0 Overview. The RS Series is Carver s multi-stage pump for fluids at moderate to high pressures. The
More informationSelf-Priming Fiberglass Pumps
Fybroc Division SERIES 16 Self-Priming Fiberglass Pumps B U L L E T I N 16B1 FYBROC THE LEADER IN CORROSION-RESISTANT FIBERGLASS PUMPING EQUIPMENT Fybroc is the leading manufacturer of fiberglass reinforced
More informationRegenerative Turbine Pumps
Bulletin 0 0 2 0 2 170 270 Series Regenerative Turbine Pumps Capacities to 0 GPM Heads to Feet MTH PUMPS 0 2 0 2 170 270 Series Regenerative Turbine Pump MTH 0 2 0 2 170 270 Series regenerative turbine
More informationTECHNICAL BROCHURE BSPMSPH R1 SOLD SEPARATELY OR BUILT IN. PrimeLine SP SPM & SPH SERIES
TECHNICAL BROCHURE BSPMSPH R1 SOLD SEPARATELY OR BUILT IN PrimeLine SP SPM & SPH SERIES FEATURES Self Priming Design: Features a replaceable check valve which acts to retain sufficient liquid in the casing
More information900 Series Split Case Fire Pump Systems
BULLETIN 900/REV. E 900 Series Split Case Fire Pump Systems MODEL 481 MODEL 483 FM Approved U L Listed motralec 4 rue Lavoisier. ZA Lavoisier. 95223 HERBLAY CEDEX Tel. : 01.39.97.65.10 / Fax. : 01.39.97.68.48
More informationSeries 1510 Centrifugal Pumps
Series 1 Centrifugal Pumps B-207H Table of Contents Useful Pump Formulas... 2 Standard Features... 3 Technical Data... Materials of Construction... Selection Charts... 6 Performance Curves... 7 Centrifugal
More informationTrash- and Solids-Handling Centrifugal Pumps Series 2100 Quality Design Features Assure Long, Trouble-Free Service
Trash- and Solids-Handling Centrifugal Pumps Series 2100 Quality Design Features Assure Long, Trouble-Free Service WIDE RANGE OF APPLICATIONS: Liquids Entrained with Solids General Industrial, Pulp & Paper,
More informationSeries 6XSHD. Specifications: Series: 6XSHD 15-30HP, 1750RPM, 60Hz HP, 1150RPM, 60Hz. 21 Frame Driver 3" Spherical Solids Handling
www.cranepumps.com Series 6XSHD 21 Frame Driver Specifications: DISCHARGE... 6", 125 lb. Horizontal Flange Slotted to accommodate 150mm ISO Flanges LIQUID TEMPERATURE... 104 F (40 C) Continuous VOLUTE...
More informationHORIZONTAL SPLIT CASE SINGLE STAGE DOUBLE SUCTION Type AE CHECKING LIST
Section Tab 1200 SINGLE STAGE DOUBLE SUCTION Section 1210 List Prices Removed 07-01-02 Use Rapid Section 1220 Data Page 0.1 & (Blank)(03-30-07) 1 & 2 (03-30-07) 2.1 & 2.2 (03-30-07) 2.21 & 2.22 (03-30-07)
More informationCLARK SOLUTIONS S Series Rotary Gear Pump Pressure to 200 PSI, Flow to 32 GPM, Drive Speed to 1800 RPM
CLARK SOLUTIONS S Series Rotary Gear Pump Pressure to 200 PSI, Flow to 32 GPM, Drive Speed to 1800 RPM DESCRIPTION Series S pumps are general purpose positive displacement gear pumps and are a good choice
More informationEFQT/EFQU. EBARA Self Priming Trash Pump. Contents Project: Model: Chk d: Date:
Contents Section Page Model Designation 2 Features 3 Standard Specifications 5 Specifications 6 Selection Chart 7 Suction Speed Flow Chart 9 Performance Curves 10 Dimension Drawings 20 Model Designation
More informationSeries 4XSHM 18 Frame Driver 3" Spherical Solids Handling
Series 4XSHM 18 Frame Driver Specifications: DISCHARGE... 4, 125 lb. Horizontal Flange Slotted to accomodate 100mm ISO Flanges LIQUID TEMPERATURE... 104 F (40 C) Continuous VOLUTE... Cast Iron ASTM A-48,
More informationHigh Capacity Centrifugal & Sprinkler Pumps
High Capacity Centrifugal & Sprinkler Pumps FW0724 1016 Supersedes 0212 Stainless steel or cast iron construction Stainless steel impellers Discharge rotates in 90 increments on some models Pressures to
More informationAURORA MODEL 410 SERIES ENGINEERING DATA MECHANICAL SEALS AND PACKING
AURORA MODEL 410 SERIES MECHANICAL SEALS AND PACKING Section 410 Page 71 Supersedes Section 410 Page 71 1 PACKING WITH OPTIONAL LANTERN RING SINGLE INSIDE UNBALANCED 3 SINGLE INSIDE BALANCED TAP OPTIONALLY
More informationSeries: G5-1¼, G6-1¼ RPM - 60Hz. CAPACITIES TO 80 GPM (5 LPS) HEADS TO 135 FEET (41 M)
Series: G5-1¼, G6-1¼ 3500 RPM - 60Hz. CAPACITIES TO 80 GPM (5 LPS) HEADS TO 135 FEET (41 M) 900 RPM - 50Hz. CAPACITIES TO 68 GPM (4.3 LPS) HEADS TO 9 FEET (8 M) USA: (937) 778-8947 Canada: (905) 457-63
More informationSeries 4XSHD. Specifications: Series: 4XSHD 3-10HP, 1750RPM, 60Hz. 18 Frame Driver 3" Spherical Solids Handling
www.cranepumps.com Series 4XSHD 18 Frame Driver Specifications: DISCHARGE... 4, 125 lb. Horizontal Flange Slotted to accommodate 100mm ISO Flanges LIQUID TEMPERATURE... 104 F (40 C) Continuous VOLUTE...
More informationASME END SUCTION PUMPS Catalogue K-90
ASME END SUCTION PUMPS Catalogue K-90 ASME B3.1-01 ISO 9001:008 REGISTERED COMPANY Engineered Pumps for Industrial and Municipal Services ASME B3.1 / ANSI END SUCTION PUMPS This catalogue provides the
More informationSeries 8SHDU. Specifications: Series: 8SHDU 25-30HP, 1750RPM, 60Hz HP, 1150RPM, 60Hz. 21 Frame Driver 3.50" Spherical Solids Handling
www.cranepumps.com Series 8SHDU 21 Frame Driver Specifications: DISCHARGE... 8", 125 lb. Horizontal Flange Slotted to accommodate 200mm ISO Flanges LIQUID TEMPERATURE... 4 F (40 C) Continuous VOLUTE...
More informationBSM ROTARY GEAR PUMPS
FT. MTD. PUMP B-Series pumps are a good choice for a variety of recirculating, mixing, and transfer applications. Typical pumped liquids include solvents, resins, and petroleum products. These pumps are
More informationSeries: G5-1¼, G6-1¼ RPM - 60Hz. CAPACITIES TO 80 GPM (5 LPS) HEADS TO 135 FEET (41 M)
Series: G5-1¼, G6-1¼ C A L L 1-866 -670-0533 O R D E R O N L IN E www.burkspumpcatalog.com 3500 RPM - 60Hz. CAPACITIES TO 80 GPM (5 LPS) HEADS TO 135 FEET (41 M) 2900 RPM - 50Hz. CAPACITIES TO 68 GPM (4.3
More information5GB, 7GB, 10GB, 18GB, 25GB, 33GB
B-33GB GB, 7GB, GB, 18GB, 2GB, 33GB High Pressure Multi-Stage Booster Pump FEATURES Multi-stage Design: Provides steady, quiet, vibration free, operation. Optional Stainless Steel Construction: Standard
More informationSUBMITTAL DATA WATER PRESSURE BOOSTER SYSTEMS
WATER PRESSURE BOOSTER SYSTEMS Model WPB-100-40TT APPLICATION Applications include commercial, industrial and other installations requiring a boost in water pressure. The NECO Water Pressure Booster System
More informationHIGH CAPACITY CENTRIFUGAL & SPRINKLER PUMPS
HIGH CAPACITY CENTRIFUGAL & SPRINKLER PUMPS FW0724 0707 Supersedes 1005 Straight Centrifugal Pumps Electric Motors Heavy Duty Straight Centrifugal Pumps High Head Straight Centrifugal Pumps Stainless Steel
More informationSeries: GNA5-1-1/4, GNA6-1-1/4
1750 RPM - 60Hz. CAPACITIES TO 40 GPM (2.5 LPS) HEADS TO 0 FEET (9 m) USA: (97) 778-8947 Canada: (905) 457-622 International: (97) 615-598 1 500 RPM - 60Hz. CAPACITIES TO 80 GPM (5 LPS) HEADS TO 15 FEET
More informationPWD. PWD API 610 BB1 Single Stage Pump
PWD PWD API 610 BB1 Single Stage Pump HYDRAULIC PERFORMANCE COVERAGE FLOW (m 3 /h) 50 Hz Performance Coverage Visit our web site at www.pumpworks610.com and specify flow and performance needs and obtain
More informationMaterials: Parts of the pump in contact with the liquid are manufactured from the following standard
Plastic Centrifugal Pump For Chemical Process DIN EN 22858 (ISO 2858)Standard DESCRIPTION pumps are manufactured to DIN EN 22858 (ISO 2858) standards in respect of design, performance and dimensions. They
More informationBulletin C Dean Pump Division. ANSI/ASME B73.1 Horizontal Process. ph2140 Telescoping Guard. ph2140 C-Face Adapter
Bulletin C 1.2.34.5 Dean Pump Division ANSI/ASME B73.1 Horizontal Process ph2140 Telescoping Guard ph2140 C-Face Adapter Dean Pump Series ph Centrifugal Process Pumps Capacities to 3200 GPM (726 m 3 /hr)
More informationM50 L50 Series - 50Hz Metric Edition Multistage Regenerative Turbine Pumps
Page M-M MTH PUMPS M L Series - Hz Metric Edition Multistage Regenerative Turbine Pumps Capacities to LPM Heads to 6 Meters Single or Multi-stage Units (up to stages) Vertical Close Coupled Horizontal
More informationPROCESS PUMPS MODEL V200 ANSI B73.2
EAGLE PROCESS PUMPS V200 ANSI B73.2 POWER END Shaft Diameters Bearings Stuffing Box PUMP END Maximum Diameter Solids Minimum Casing Thickness Casing Corrosion Allowance Working Pressure Test Pressure
More informationANSI Centrifugal Process Pumps. 911 Series
ANSI Centrifugal Process Pumps 9 Series WHAT IS AN ANSI PUMP In 977, the American National Standard Institue (ANSI) established criteria for centrifugal pumps in terms of dimension, chemical composition
More informationSeries 4XSHV. Specifications: Series: 4XSHV , 3450RPM, 60Hz 2-10HP, 1750RPM, 60Hz. 18 Frame Driver 3" Spherical Solids Handling
Series 4XSHV 18 Frame Driver Specifications: DISCHARGE... 4, 125 lb. Horizontal Flange Slotted to accomodate 100mm ISO Flanges LIQUID TEMPERATURE... 104 F (40 C) Continuous VOLUTE... Cast Iron ASTM A-48,
More information2CDU70/206-2HP 2CDU70/306-3HP CDU120/306-3HP 2CDU200/506-5HP 607
Model CDX/CDU Contents CDX/CDU Item No. Specifications Selection Performance Pump Sectional Motor Chart Curve Dimensions View Data CDXU70/06-HP CDXU70/6-HP 5 6 8 6 CDXU0/6-HP CDXU00/6-5HP 7 CDU70/06-HP
More informationCENTRIFUGAL PUMPS CLOSE-COUPLED 7.5" FEATURES
FEATURES Volute: Ductile iron for heavy-duty service; back pullout design; can be rotated for ease of installation Impeller: Enclosed design for high efficiency; configured for superior NPSH characteristics;
More informationPUMPS FOR INDUSTRY. The Vertical Pump Specialists CONTENTS: Introduction & User List. Product Overview. Vertical Process Pumps...
PUMPS FOR INDUSTRY CONTNTS: The Vertical Pump Specialists Introduction & User List Product Overview Vertical Process Pumps... Series 600 Vertical Sewage Pumps... Series 700 Vertical Sump Pumps... Series
More informationBSM ROTARY GEAR PUMPS
-SERIES FLG. MTD. PUMP PUMP FOOT The BSM -Series pumps are designed to provide quiet and efficient service at standard motor speeds, moderately high pressures. Typical applications are supplying hydraulic
More informationSeries 6SHM. Specifications: Series: 6SHM 15-30HP, 1750RPM, 60Hz HP, 1150RPM, 60Hz. 21 Frame Driver 3" Spherical Solids Handling
www.cranepumps.com Series 6SHM 21 Frame Driver Specifications: DISCHARGE... 6", 125 lb. Horizontal Flange Slotted to accommodate 150mm ISO Flanges LIQUID TEMPERATURE... 104 F (40 C) Continuous VOLUTE...
More informationITT. Goulds Pumps. 5GB, 7GB, 10GB, 18GB, 25GB, 33GB High Pressure Multi-Stage Booster Pump. Engineered for life. Residential Water Systems FEATURES
Goulds Pumps GB, 7GB, 1GB, 18GB, 2GB, 33GB High Pressure Multi-Stage Booster Pump FEATURES Multi-stage Design: Provides steady, quiet, vibration free, operation. Optional Stainless Steel Construction:
More informationFire Protection. FP-XA End Suction
Fire Protection FP-XA End Suction PRODUCT BULLETIN MODEL FP-XA END SUCTION CPS Model FP-XA End Suction pumps are used in a variety of fire fighting applications. These rugged and efficient centrifugal
More informationGIS/ GISO Series End Suction Pumps TECHNICAL BULLETIN
GIS/ GISO Series End Suction Pumps TECHNICAL BULLETIN Goulds Water Technology is renowned for manufacturing the highest quality pumping equipment utilizing the best engineering practices available worldwide.
More informationCENTRIFUGAL PUMPS HYDRAULIC DRIVEN 9" FEATURES SPECIFICATIONS APPLICATIONS
FEATURES Volute: Heavy-duty cast iron construction; back pullout design; can be rotated for ease of installation Impeller: Enclosed, cast iron design for high efficiency; double keyed for improved reliability
More informationTECHNICAL BROCHURE B45-70HB R2 45HB, 70HB HIGH PRESSURE CENTRIFUGAL BOOSTER PUMP
TECHNICAL BROCHURE B45-7HB R2 45HB, 7HB HIGH PRESSURE CENTRIFUGAL BOOSTER PUMP FEATURES Multi-Stage Design: This configuration provides a steady, quiet and vibration-free operation for years of trouble-free
More informationCENTRIFUGAL PUMPS 13" CLOSE-COUPLED FEATURES
FEATURES Volute: Cast iron for heavy-duty service; back pull-out design; can be rotated for ease of installation; split volutes for reduction in radial bearing load (6 x 8-13 and 8 x 10-13) Impeller: Enclosed
More informationEVMU. Model EVMU / EVMUG / EVMUL Contents. EBARA Stainless Steel Vertical Multistage
Model / G / L Contents Item No. Specifications Selection Performance Pump Sectional Chart Curve Dimensions View 3 5 10 18 G32 G45 G64 L3 L5 L10 L18 L32 L45 L64 803 804 803 804 805 806 807 808 809 810 811
More informationFeatures: Applications: Irrigation. Commercial. Construction. Municipal. Mining
Frame Mount 7.5" BOOK: FMT-015 DATE: Mar. 1, 2012 Features: Volute: Ductile iron for heavy-duty service. Back pullout design. Can be rotated for ease of installation. Impeller: Enclosed design for high
More informationSKHS SERIES 2 HP 1-1/2 HP 1 HP 1/2 HP CAPACITY-U.S. G.P.M.
Performance RPM: 3450 Discharge: 2" Solids: 2" Wholesale Products Page: 6560-1 Section: Performance 80 70 2 HP TOTAL DYNAMIC HEAD-FEET 60 50 40 30 20 1 HP 1-1/2 HP 1/2 HP 10 0 0 32 64 96 128 160 192 CAPACITY-U.S.
More informationWilo IL Vertical Inline Pumps. Engineering Specification
Wilo IL Vertical Inline Pumps Engineering Specification PART 1 - GENERAL 1.1 SUMMARY A. Pump shall be Series IL, long (split)-coupled, single stage vertical inline centrifugal pump as manufactured by WILO-NA.
More information