SUGGESTED SPECIFICATIONS

Size: px
Start display at page:

Download "SUGGESTED SPECIFICATIONS"

Transcription

1 PART 1 - GENERAL 1.01 SCOPE A. Pumps to be supplied under this specification shall be of a severe duty, recessed cupped impeller design suitable for use in (SLUDGE, GRIT, ETC. APPLICATIONS) with a 20 year performance life. The pump liquid end (Suction Cover, Casing, Impeller & Rear Liner) shall be provided with a guarantee against mechanical failure due to materials and workmanship or abrasive wear under the original specified operating conditions. The guarantee shall be for municipal installations and shall include the replacement of the part for 5 years from the date of shipment. The liquid end guarantee shall be provided in certificate form, signed by an officer of the manufacturing corporation, and listed in the submittal. Units will be horizontal (A: SIDE-BY-SIDE, B: OVERHEAD MOTOR MOUNTED, C: Z-BASE) V-Belt drive configuration having a wet end construction of 28% chrome iron with a 420SS shaft sleeve and cast iron stuffing box. The power end will be cast iron (OIL or GREASE) lubricated with bearings rated for a minimum of 100,000 hours B- 10. All equipment shall be suitable for the application and in compliance with these specifications. B. The required units shall be Morris Pumps Model 6100CT or a pre-approved equal QUALITY ASSURANCE A. The equipment covered by this specification is intended to be a standard product of proven reliability as manufactured by Morris Pumps, Aurora, IL or pre-approved equal and having at least twenty (20) years of experience in the production of such equipment and five (5) years successful field operation of the actual proposed equipment. All units specified in this specification shall be supplied by a single pump manufacturer. Pumps are to be engineered and manufactured under a written Quality Assurance program certified to the ISO 9001:2000 Quality System Standard. The Quality Assurance program is to have been in effect for at least five (5) years and shall include a written record of periodic internal and external audits to confirm compliance with ISO 9001:2000 requirements. (OPTION: In addition to the pumps the pump manufacturer shall supply the motors and drives and take responsibility for the components within their scope of supply). B. Pumps shall conform to these specifications and the Hydraulic Institute Standards (latest edition). (Option: The pump manufacturer shall supply a certificate of conformance at time of shipment. A copy will be included with the shipment to confirm that the pumps supplied meet the required specifications.) C. All pumps shall be given a performance test in accordance with the Hydraulic Institute Standards (latest edition) as required by the specifications. PART 2 - PRODUCT SELECTION 2.01 OPERATING SELECTION A. The pump shall be designed for continuous operation and operate at/or below the vibration levels listed in the Hydraulic Institute Standards (latest edition). The number of starts for a 24-hour period shall not exceed that as limited by the driver manufacturer. B. The pump operating and service conditions shall be as listed on the attached TABLE 1 - PERFORMANCE DATA. The Rated Condition as listed in TABLE 1 - PERFORMANCE DATA shall be the rated condition as defined by the Hydraulic Institute Standards. This condition will be used for any performance evaluation. Other Rated Conditions must be within 5% of the values and are furnished to describe the full range of the operating requirements. Date 10/1/07 PAGE

2 PART 3 - PRODUCT DESIGN 3.01 The pump shall have a continuously rising head capacity curve from runout to shutoff. The pump shall be designed to operate continuously for an extended period of time at any point in the specified operating range of the curve without cavitation, overheating or excessive vibration. The motor nameplate horsepower rating shall not be exceeded by the pump brake horsepower requirements at any point of the specified operating range. PART 4 - MATERIALS OF CONSTRUCTION 4.01 The recessed cupped impeller pump shall conform to the materials of construction as listed for this design MATERIALS PUMP COMPONENT CASING IMPELLER SUCTION COVER REAR LINER STFG. BOX COVER IMPELLER BOLT SHAFT SLEEVE SHAFT LANTERN RING PACKING STFG. BOX GLAND BEARING FRAME MATERIAL Cast Iron ASTM A48, Cl Stainless Steel 420SS ASTM A743, Grade CA-40 with a min. hardness of 450 BHN Steel, AISI 1045 H.R. Teflon Square Braid Graphite Polymer Fiber 316SS ASTM A743, Gr. CF-8M Cast Iron ASTM A48,Cl. 35B 4.03 CASING CONSTRUCTION A. The pump casing shall be reversible for RH or LH rotation without the need for changing the impeller or casing and shall be of sufficient strength and metal thickness to insure long life, accurate alignment and reliable operation. The volute of the pump casing shall have smooth fluid passages large enough at all points to pass any size solid which can pass through the discharge and provide smooth unobstructed flow. The casing shall have a separate and removable suction cover, rear liner and stuffing box cover. B. The discharge flange shall conform to ANSI B16.1, Class 125 lb., flat face, of standard size with drilled holes. C. The casing shall have machined registered fits to minimize localized wear, assure proper alignment of the suction cover and rear liner and will be sealed by isolated Buna-N O-Rings. The clearance between the registered fits shall be no greater than.025". An undercut of no more than.050" shall be provided for ease of maintenance. Ground nontoleranced tapered fits which increase eddy currents and promote localized wear will not be accepted. D. The casing shall have a minimum thickness as shown below to provide for maximum wear allowance. 2" PUMPS.75" 3" PUMPS.75" 4" PUMPS.88" 6" PUMPS 1.00" 8" PUMPS 1.12" PAGE Date 10/1/07

3 4.04 IMPELLER CONSTRUCTION A. The impeller shall be of the single suction vortex design recessed into the rear wear liner and out of the flow path. The impeller shall be of a cupped shape with the impeller shroud fully encasing the tips of the impeller vanes preventing direct impingement of the pumpage on the wear liner or casing resulting in localized wear. Radial discharging impellers will not be accepted. B. The shroud of the impeller shall incorporate pump out vanes for the purpose of maintaining a solids free area behind the impeller to decrease wear and extend the life of the stuffing box seal. C. The impeller shall be straight bored and keyed to the pump shaft. The impeller shall be held in place by a recessed 18-8 SS impeller bolt and will be sealed front and back with Buna-N O-rings to provide a dry shaft design. The impeller bore shall be directly through the homogeneous impeller material. The use of soft metal casting inserts which could break loose due to torque and fatigue associated with starting and stopping will not be accepted. D. The cupped impeller shall be capable of being easily removed and remounted on the pump shaft without the use of special procedures to confirm impeller bore engagement. Designs which do not utilize a machined keyway for torque transfer shall not be acceptable. E. Due to the size, shape and weight of the cupped impeller design. A special tool shall be provided to assist with handling the impeller during maintenance. F. The impeller shall provide the same hydraulic performance regardless of rotation SUCTION COVER CONSTRUCTION A. The suction cover shall have machined registered fits to minimize localized wear, assure proper alignment of the suction cover and rear liner and be sealed by isolated Buna-N O-Rings. The clearance between the registered fits shall be no greater than.025". An undercut of no more than.050" shall be provided for ease of maintenance. Ground non-toleranced tapered fits which increase eddy currents and promote localized wear will not be accepted. The purpose of the machined fit is to prevent localized wear due to loose tolerances, simplify removal and replacement, and to assure proper fit and alignment. B. The suction flange shall conform to ANSI B16.1, Class 125 lb., flat face, of standard size with drilled holes. The suction cover shall have a minimum thickness as shown below to provide for maximum wear allowance. 2" PUMPS.88" 3" PUMPS 1.00" 4" PUMPS 1.25" 6" PUMPS 1.25" 8" PUMPS 1.50" 4.06 REAR LINER A. The rear liner shall have machined registered fits to minimize localized wear, assure proper alignment of the suction cover and rear liner and be sealed by isolated Buna-N O-Rings. The clearance between the registered fits shall be no greater than.025". An undercut of no more than.050" shall be provided for ease of maintenance. Ground non-toleranced tapered fits which increase eddy currents and promote localized wear will not be accepted. The purpose of the machined fit is to prevent localized wear due to loose tolerances, simplify removal and replacement, and to assure proper fit and alignment. B. The rear liner shall have a bolt circle of tapped holes for attachment to the bearing frame. The bolt circle shall be drilled and tapped directly into the homogeneous rear liner material. The use of soft metal casting inserts which could break loose due to torque during bolt tightening will not be accepted. Date 10/1/07 PAGE

4 4.07 STUFFING BOX COVER A. The stuffing box cover shall be clamped between the rear liner and the bearing frame and will be provided with machined registered fits to assure true alignment with the pump shaft. B. The stuffing box shall be suitable for either packing or mechanical seals. The stuffing box will be provided with two 3/8" NPT flush taps for piping arrangement flexibility and shall have a 4 bolt gland pattern. C. The packed stuffing box shall be provided with 5 rows of packing, a Teflon lantern ring, a 316SS split gland and 316SS gland hardware. D. A taperbore stuffing box shall be available as an option for use with single mechanical seals on abrasive services. E. Ample room shall be provided for maintenance of the stuffing box. As a minimum the distance from the face of the stuffing box to the first obstruction shall be 3" SHAFT SLEEVE A. The shaft sleeve shall be of a hook style design and will extend from the impeller past the face of the stuffing box. The sleeve shall be sealed against the impeller with an O-Ring to provide a dry shaft design. Sleeve designs that do not fully protect the shaft against the corrosive and abrasive effects of the pumpage will not be accepted. B. The sleeve shall be keyed to the shaft to prevent rotation relative to the shaft SHAFT A. The shaft shall be high strength, accurately machined and of sufficient size, with liberal safety factor, to transmit the maximum horsepower and loading from the impeller to the bearings when the pump is operating at the maximum allowable speed. B. The pump shaft shall be designed such that the maximum shaft deflection shall not exceed.002"at the stuffing box BEARING FRAME A. The bearing frame shall be a one piece rigid cast iron construction, providing a self centering and self indexing fit with the rear liner and stuffing box cover of the pump to insure proper alignment. B. The bearing frame shall be designed with an integral stuffing box drainage collection chamber with a drilled and tapped 3/4" NPT drain. C. The bearing frame shall be designed so that the complete rotating assembly can be removed without disturbing the suction and discharge piping. D. The bearing frame inboard and outboard end covers shall be equipped with lip type grease seals and deflectors to prevent the entrance of contaminants. (Option: Non-contacting labyrinth seals shall be available.) E. The bearing frame shall be provided with oil bath lubricated inboard and outboard single row tapered roller bearings both designed to handle radial and thrust loads. The bearings shall provide a minimum B-10 life of 100,000 hours at any point on the operating performance curve. F. Bearings shall be available for grease lubrication. PAGE Date 10/1/07

5 4.11 PUMP MOUNTING A. The pump shall be provided with a common base of sufficient size to accommodate the pump, driver and V-Belt drive or coupling. The base shall be (A: SIDE-BY-SIDE, B: OVERHEAD MOTOR MOUNTED, C: Z-BASE). The base shall be of sufficient strength to support all loads to which it may be subjected. If the specifications define a future size drive system, the sub-base shall be sized and machined for the present and future drive system. The subbase may use removable or adjustable spacers to accommodate the initial and future drive system. C. The pump manufacturer shall indicate on the certified pump outline drawing the location of the anchor bolts required for the attachment of the pump sub-base to the concrete support base. The anchor bolts shall be supplied by the installation contractor and positioned prior to concrete placement with embedment determined by the Engineer V-BELT DRIVE V-Belt drives shall be selected with a minimum of a 1.3 service factor over the nameplate rated horsepower of the driver. Drives shall have variable pitch or single pitch sheaves. If single pitch drives are provided, two additional sheaves shall be supplied to provide a speed range of 20 to 30 RPM above and below the rated pump RPM using a common set of belts GUARDS All drives shall be provided with fabricated guards of adequate size and designed to be in compliance with OSHA safety standards. Guards shall have hinged access ports for verifying the pump and motor RPM. PART 5 - DRIVER The required pump driver shall be supplied in accordance with specification The driver shall be selected to be non-overloading over the specified pumping head range. PART 6 - FACTORY TESTING Testing shall be (A: NON WITNESSED / B: WITNESSED) All hydro and performance testing shall be completed prior to the application of any final paint and/or coating. All factory testing shall be in accordance with the standards of the Hydraulic Institute (latest edition). All testing is to be performed at the manufacturer's facility using lab personnel, instrumentation and drives Written approval of all testing will be required prior to release to shipment Hydrostatic testing shall be performed on the assembled pump with the liquid end components being held at a pressure of 150 PSI, but not greater than the allowable mechanical seal pressure, for a period of not less than (A: FIVE MINUTES / B: THIRTY MINUTES). A hydro test certification shall be completed after the test and included in the final data package Performance testing shall include head, capacity and power readings at eight (8) points including the rated point, to determine the actual pump performance and efficiency. Performance testing shall establish that the pump is free of overheating, cavitation and excessive vibration over the specified conditions. A certified performance curve shall be completed after the test and included in the final data package A ten day notice shall be given to the engineer prior to the start of any witness testing Field functional testing will be performed to insure proper mechanical operation at the job site. All testing to be used for performance evaluation shall be performed at the pump manufacturer's facility Motor tests and test reports shall be provided as required in accordance with specification as stated in part 5. Date 10/1/07 PAGE

6 TABLE 1 - PERFORMANCE DATA Pump Item Number... Number of units required... Rated Duty Point Condition Capacity (Flow)... GPM TDH (Total Dynamic Head)... Feet Minimum Efficiency... % (Alternate) Condition "B" Capacity (Flow)... GPM TDH (Total Dynamic Head)... Feet Minimum Efficiency... % (Alternate) Condition "C" Capacity (Flow)... GPM TDH (Total Dynamic Head)... Feet Minimum Efficiency... % Minimum Shutoff Head... Feet Minimum motor horsepower required... HP Electrical Characteristics Required... Volt Hz. Ph. Maximum pump operating speed... RPM Minimum Suction Size... inches Minimum Discharge Size... inches Minimum Solid Size required to pass through Impeller... inches diameter Maximum NPSH Required... Feet Minimum NPSH Available... Feet Liquid to be Pumped... Pumping Temperature... F Specific Pumping Temperature... PAGE Date 10/1/07

4500C Series Vortex Pumps

4500C Series Vortex Pumps Section 009 Page 003 4500C Series Vortex Pumps Table of Contents 4500C Performance 2" x 2" - 4523C, Multiple Speed... 004 3" x 3" - 4523C, Multiple Speed... 004 4" x 4" - 4522C, Multiple Speed... 005 4"

More information

855 Filtrate Pump, Close Coupled and Overhead Mounted Pumps

855 Filtrate Pump, Close Coupled and Overhead Mounted Pumps 855 Filtrate Pump, Close Coupled and Overhead Mounted Pumps Technical Specification Pages This page left intentionally blank. 1.0 Overview. The 855 Series is Carver s offering specifically designed to

More information

SUGGESTED SPECIFICATIONS Pump Frames NS3 thru OMC5

SUGGESTED SPECIFICATIONS Pump Frames NS3 thru OMC5 SOLIDS-HANDLING WASTEWATER PUMPS Pump Frames NS3 thru OMC5 GENERAL Furnish and install Vertical Closed-Shaft Wet-Pit Pumping Units complete with all accessories and appurtenances as shown in the plans

More information

Centrifugal End Suction Fire Pumps

Centrifugal End Suction Fire Pumps Centrifugal End Suction Fire Pumps 1 Centrifugal End Suction Fire Pumps Product Overview American-Marsh Model FP-REF End Suction pumps are used in a variety of fire protection services every day. These

More information

Goulds Model JC. Lenntech. Slurry Pump. Tel Fax

Goulds Model JC. Lenntech. Slurry Pump. Tel Fax Goulds Model JC Slurry Pump Lenntech info@lenntech.com Tel. +31-152-610-900 www.lenntech.com Fax. +31-152-616-289 Goulds JC Designed for Handling a Wide Range of Corrosive / Abrasive Slurries Capacities

More information

Goulds Small Capacity Double Suction Pump

Goulds Small Capacity Double Suction Pump Goulds 3410 Small Capacity Double Suction Pump 3410 Double Suction Pumps Designed for a Wide Range of Industrial, Municipal, Capacities to 7,000 GPM (1591 m3/h) Heads to 550 feet (168 m) Temperatures to

More information

Goulds 3181 High-temperature/Pressure Paper Stock/ Process Pumps

Goulds 3181 High-temperature/Pressure Paper Stock/ Process Pumps High-temperature/Pressure Paper Stock/ Process Pumps Designed to Handle High Temperature and High Pressure Services of the Pulp & Paper Industries Capacities to 13,000 GPM (3000 m 3 /h) Heads to 410 feet

More information

PWA-IL B73.2 IN-LINE

PWA-IL B73.2 IN-LINE PWA-IL ANSI/ASME B73.2 IN-LINE PROCESS PUMP PWA-IL ANSI/ASME B73.2 IN-LINE PROCESS PUMP COMPETITIVE ADVANTAGES vs. Ductile Iron n High-strength, impact resistant liquid ends for improved durability and

More information

PROCESS PUMPS MODEL V200 ANSI B73.2

PROCESS PUMPS MODEL V200 ANSI B73.2 EAGLE PROCESS PUMPS V200 ANSI B73.2 POWER END Shaft Diameters Bearings Stuffing Box PUMP END Maximum Diameter Solids Minimum Casing Thickness Casing Corrosion Allowance Working Pressure Test Pressure

More information

3312 Model. pumping Model Model AURORA Series HORIZONTAL AND VERTICAL CLOSE-COUPLED PUMPS

3312 Model. pumping Model Model AURORA Series HORIZONTAL AND VERTICAL CLOSE-COUPLED PUMPS 3312 Model pumping 3314 Model 3311 Model AURORA 3310 Series HORIZONTAL AND VERTICAL CLOSE-COUPLED PUMPS WWW.AURORAPUMP.COM AURORA 3310 Series Horizontal and Vertical Close-Coupled Pumps Capacities to 3800

More information

AURORA Series MODEL 3560 ASME/ANSI B73.1M INDUSTRIAL PROCESS PUMPS

AURORA Series MODEL 3560 ASME/ANSI B73.1M INDUSTRIAL PROCESS PUMPS AURORA 3500 Series MODEL 3560 ASME/ANSI B73.M INDUSTRIAL PROCESS PUMPS WWW.AURORAPUMP.COM AURORA 3500 Series Model 3560 ASME/ANSI B73.M Industrial Process Pumps Capacities to 7000 GPM (590 m 3 /hr) Heads

More information

Goulds 3186 High-temperature/Pressure Paper Stock/ Process Pumps

Goulds 3186 High-temperature/Pressure Paper Stock/ Process Pumps Lenntech info@lenntech.com Tel. +31-152-610-900 www.lenntech.com Fax. +31-152-616-289 Goulds 3186 High-temperature/Pressure Paper Stock/ Process Pumps Goulds 3186 Designed to Handle High Temperature and

More information

EN. 850 Filtrate Pumps. Technical Specification Pages

EN. 850 Filtrate Pumps. Technical Specification Pages 850 17.01.EN 850 Filtrate Pumps Technical Specification Pages 850 Series Filtrate Pump 850 17.01.EN This page left intentionally blank. 1.0 Overview. The 850 is Carver s filtrate pump line designed for

More information

Bulletin BX-512H. Bell & Gossett. Series HSC-S Pumps Technical Bulletin. Bell & Gossett. Part of the. Equipment Selection Programs

Bulletin BX-512H. Bell & Gossett. Series HSC-S Pumps Technical Bulletin. Bell & Gossett. Part of the. Equipment Selection Programs Bulletin BX-1H Bell & Gossett Series HSC-S Pumps Technical Bulletin Part of the Bell & Gossett Equipment Selection Programs TABLE OF CONTENTS Useful Pump Formulas...............................................

More information

HORIZONTAL SPLIT CASE SINGLE STAGE DOUBLE SUCTION Type AE CHECKING LIST

HORIZONTAL SPLIT CASE SINGLE STAGE DOUBLE SUCTION Type AE CHECKING LIST Section Tab 1200 SINGLE STAGE DOUBLE SUCTION Section 1210 List Prices Removed 07-01-02 Use Rapid Section 1220 Data Page 0.1 & (Blank)(03-30-07) 1 & 2 (03-30-07) 2.1 & 2.2 (03-30-07) 2.21 & 2.22 (03-30-07)

More information

NC State University Design and Construction Guidelines Division 23 Hydronic Pumps

NC State University Design and Construction Guidelines Division 23 Hydronic Pumps 1.0 Purpose A. The following guidelines apply to the selection of pumps primarily for circulating water. It is the goal of NC State to purchase pumps that are selected to provide a long service life, minimal

More information

High-Temperature and Pressure Paper Stock / Process Pump

High-Temperature and Pressure Paper Stock / Process Pump 3186 High-Temperature and Pressure Paper Stock / Process Pump 3186 Designed to handle High-Temperature and High-Pressure services of the Pulp & Paper Industries. Capacities to 3000 m³/h (13,000 GPM) Heads

More information

Goulds Severe Duty Slurry Pump

Goulds Severe Duty Slurry Pump Goulds 5500 Severe Duty Slurry Pump 5500 Proven leadership in mining and mineral processing Proven Leadership 100 years of slurry pumping experience. Many industry firsts including: hard metal slurry pump,

More information

Basic Hydraulic Features. Basic Mechanical Features

Basic Hydraulic Features. Basic Mechanical Features APRIL 2006 1.0 Overview The ETA is designed for flow rates that fall beyond the range of most end suction pumps. Performance extends to 9,500 GPM, 440 feet of head, and 88% efficiency. This range is covered

More information

Waterfall Pumps Manufacturing

Waterfall Pumps Manufacturing Waterfall Pumps Manufacturing Our Vision for the future to become the world s premier provider of fire protection pumps. Our ongoing mission is to be the customers first choice, a trusted provider and

More information

SEVERE DUTY CUP TYPE RECESSED IMPELLER PUMPS

SEVERE DUTY CUP TYPE RECESSED IMPELLER PUMPS SERIES 6100 TYPE CT SEVERE DUTY CUP TYPE RECESSED IMPELLER PUMPS BUILT FOR SUPERIOR PERFORMANCE 6100 SERIES / CUP TYPE SEVERE DUTY RECESSED IMPELLER PUMPS DESIGNED TO HANDLE LARGE, ABRASIVE SOLIDS LONGEST

More information

340 Series Double Suction Split Case Pumps

340 Series Double Suction Split Case Pumps 340 Series Double Suction Split Case Pumps Flows to: 30,000+ GPM Heads to: 550 Feet Temperatures to: 250 F 140 Years of Pump Manufacturing American-Marsh Pumps, one of the oldest pump lines in America,

More information

Index - Section 14 End Suction Pump Semi-Open Impeller

Index - Section 14 End Suction Pump Semi-Open Impeller Index - Section End Suction Pump Semi-Open Impeller ITEM S Product Numbering System...1 Typical Architects / Engineers Specifi cations - Series 4000...2 Seal Application...3-4 Technical Charts...5-6 Pump

More information

AURORA 3500 SERIES MODEL 3550 ASME/ANSI B73.1 INDUSTRIAL PROCESS PUMPS

AURORA 3500 SERIES MODEL 3550 ASME/ANSI B73.1 INDUSTRIAL PROCESS PUMPS AURORA 3500 SERIES MODEL 3550 ASME/ANSI B73.1 INDUSTRIAL PROCESS PUMPS WWW.AURORAPUMP.COM INDUSTRIAL PROCESS PUMPS AURORA 3500 SERIES Model 3550 ASME/ANSI B73.1 Industrial Process Pumps Capacities to GPM

More information

Model 3550 ASME/ANSI B73.1M Industrial Process Pumps

Model 3550 ASME/ANSI B73.1M Industrial Process Pumps 3500 Series Model 3550 ASME/ANSI B73.1M Industrial Process Pumps The Aurora Model 3550 was designed to perform in the toughest industrial applications whether in the chemical, petro-chemical, mining, pulp

More information

G&L Pumps. TECHNICAL Brochure BAC8100. Series A-C 8100 SPLIT CASE PUMPS

G&L Pumps. TECHNICAL Brochure BAC8100. Series A-C 8100 SPLIT CASE PUMPS TECHNICAL Brochure BAC8 Series A-C 8 SPLIT CASE PUMPS TABLE OF CONTENTS Useful Pump Formulas 2 Performance Curves 3-5 Materials of Construction (Standard) 6 Materials of Construction (Optional) 7 Pump

More information

900 Series Split Case Fire Pump Systems

900 Series Split Case Fire Pump Systems BULLETIN 900/REV. E 900 Series Split Case Fire Pump Systems MODEL 481 MODEL 483 FM Approved U L Listed motralec 4 rue Lavoisier. ZA Lavoisier. 95223 HERBLAY CEDEX Tel. : 01.39.97.65.10 / Fax. : 01.39.97.68.48

More information

PWD. PWD API 610 BB1 Single Stage Pump

PWD. PWD API 610 BB1 Single Stage Pump PWD PWD API 610 BB1 Single Stage Pump HYDRAULIC PERFORMANCE COVERAGE FLOW (m 3 /h) 50 Hz Performance Coverage Visit our web site at www.pumpworks610.com and specify flow and performance needs and obtain

More information

Axially Split Case Pumps

Axially Split Case Pumps Axially Split Case Pumps A-C Pump A-C SPL Standard Design Features for a Wide Range of Heavy Duty In STUFFING BOX Packing is standard on the A-C products. A wide variety of mechanical seals, including

More information

High Temperature Chemical Process Inline Pumps

High Temperature Chemical Process Inline Pumps Bulletin C-1.2.21. Dean Pump Division High Temperature Chemical Process Inline Pumps Series DL Series DL High Temperature Chemical Process Inline Pumps Capacities to 6 GPM (182 m 3 /hr) Heads to feet (167

More information

VSC /VSCS Pumps Technical Brochure

VSC /VSCS Pumps Technical Brochure VSC /VSCS Pumps Technical Brochure BX-4C VSC/VSCS Construction Materials STANDARD SEAL CONFIGURATION PART NAME STANDARD CONSTRUCTION ASTM NO. Casing Cast iron A159 Class G0 Volute cover plate (Outboard)

More information

ZPP and Z22 Double Suction Axially Split Single Stage Centrifugal Pumps

ZPP and Z22 Double Suction Axially Split Single Stage Centrifugal Pumps ZPP and Z22 Double Suction Axially Split Single Stage Centrifugal Pumps Main Applications Features and Benefits ZPP and Z22 double suction axially split single stage centrifugal pumps are used for demanding

More information

3800 Series. Single Stage End Suction Pumps. Capacities to 4200 G.P.M. (954 m 3 /hr) Heads to 520 Feet (180 Meters) Temperatures to 300 F (149 C)

3800 Series. Single Stage End Suction Pumps. Capacities to 4200 G.P.M. (954 m 3 /hr) Heads to 520 Feet (180 Meters) Temperatures to 300 F (149 C) 3800 Series Single Stage End Suction Pumps Capacities to 200 G.P.M. (95 m 3 /hr) Heads to 520 Feet (180 Meters) Temperatures to 300 F (19 C) MODEL 380 Aurora 3800 Pump Setting New Standards of Efficiency

More information

1100 Series Multi-Stage Vertical Turbine Pumps

1100 Series Multi-Stage Vertical Turbine Pumps 1100 Series Multi-Stage Vertical Turbine Pumps Capacities to 40,000 GPM Heads to 1,500 Feet Temperatures to 200 F Water Lubricated Open Lineshaft Vertical Hollow Shaft Motor The vertical hollow shaft motor

More information

NORTHWESTERN UNIVERSITY PROJECT NAME JOB # ISSUED: 03/29/2017

NORTHWESTERN UNIVERSITY PROJECT NAME JOB # ISSUED: 03/29/2017 SECTION 23 2123 - PUMPS PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 01 Specification Sections,

More information

Fire Protection. FP-XA End Suction

Fire Protection. FP-XA End Suction Fire Protection FP-XA End Suction PRODUCT BULLETIN MODEL FP-XA END SUCTION CPS Model FP-XA End Suction pumps are used in a variety of fire fighting applications. These rugged and efficient centrifugal

More information

barmesapumps.com WHAT IS AN ANSI PUMP

barmesapumps.com WHAT IS AN ANSI PUMP WHAT IS AN ANSI PUMP In 1977, the American National Standard Institue (ANSI) established criteria for centrifugal pumps in terms of dimension, chemical composition of the materials and safety specifications,

More information

SECTION PUMPS GENERAL PUMPS PART RELATED DOCUMENTS

SECTION PUMPS GENERAL PUMPS PART RELATED DOCUMENTS SECTION 15160 - PUMPS PART 1 - GENERAL 1.01 RELATED DOCUMENTS A. Basic Requirements: Provisions of Section 15010, BASIC MECHANICAL REQUIREMENTS and Section 15030, ELECTRICAL REQUIREMENTS FOR MECHANICAL

More information

Goulds API th Edition/ISO nd Edition API OH3 Overhung. Vertical In-Line with Bearing Frame. An ITT Brand

Goulds API th Edition/ISO nd Edition API OH3 Overhung. Vertical In-Line with Bearing Frame. An ITT Brand Goulds 3910 API-610 11th Edition/ISO 13709 2 nd Edition API OH3 Overhung. Vertical In-Line with Bearing Frame An ITT Brand 3910 Designed to Handle High-Temperature and High-Pressure Services of the Oil

More information

Goulds High-Pressure Multi-Stage Pumps

Goulds High-Pressure Multi-Stage Pumps Goulds 3311 High-Pressure Multi-Stage Pumps Goulds Model 3311 Multistage Pumps Designed for a Wide Range of High Pressure Services Goulds Model 3311 is a radial split, segmented ring multistage pump...

More information

PUMPS FOR INDUSTRY. The Vertical Pump Specialists CONTENTS: Introduction & User List. Product Overview. Vertical Process Pumps...

PUMPS FOR INDUSTRY. The Vertical Pump Specialists CONTENTS: Introduction & User List. Product Overview. Vertical Process Pumps... PUMPS FOR INDUSTRY CONTENTS: The Vertical Pump Specialists Introduction & User List Product Overview Vertical Process Pumps... Series 600 Vertical Sewage Pumps... Series 700 Vertical Sump Pumps... Series

More information

PWA ANSI / ASME B73.1 PROCESS PUMP

PWA ANSI / ASME B73.1 PROCESS PUMP PWA ANSI / ASME B73.1 PROCESS PUMP COMPETITIVE ADVANTAGES Carbon Steel vs. Ductile Iron n High strength, impact resistant Carbon Steel liquid ends for improved durability and pressure containment at no

More information

XFLO XS SERIES. Single Stage Double Suction Split Casing Centrifugal Pump

XFLO XS SERIES. Single Stage Double Suction Split Casing Centrifugal Pump XFLO P U M P S XS SERIES Single Stage Double Suction Split Casing Centrifugal Pump General and Construction 1. Applications Waterworks, Irrigation, Drainage pumping stations, Power stations, Industrial

More information

ITT. Goulds Pumps. G&L Series SSH S & M-Group 316 Stainless Steel End Suction Pumps. Engineered for life. Commercial Water.

ITT. Goulds Pumps. G&L Series SSH S & M-Group 316 Stainless Steel End Suction Pumps. Engineered for life. Commercial Water. ITT Goulds Pumps G&L Series SSH S & M-Group 316 Stainless Steel End Suction Pumps www.goulds.com Engineered for life A Full Range of Product Features Superior Materials of Construction: AISI Type 316L

More information

EFQT/EFQU. EBARA Self Priming Trash Pump. Contents Project: Model: Chk d: Date:

EFQT/EFQU. EBARA Self Priming Trash Pump. Contents Project: Model: Chk d: Date: Contents Section Page Model Designation 2 Features 3 Standard Specifications 5 Specifications 6 Selection Chart 7 Suction Speed Flow Chart 9 Performance Curves 10 Dimension Drawings 20 Model Designation

More information

THOMAS DREDGE PUMP RANGES

THOMAS DREDGE PUMP RANGES THOMAS DREDGE PUMP RANGES Pump Technologies Thomas Dredge The Metso Thomas Dredge Pumps are designed for hydraulic dredging and mining applications. These rugged pumps feature extra heavy metal sections

More information

Product Numbering System Typical Specifi cations, Models 4AC, 4AE, 6AC, 6AE, 8AC Pump Assembly, Types AC & AE

Product Numbering System Typical Specifi cations, Models 4AC, 4AE, 6AC, 6AE, 8AC Pump Assembly, Types AC & AE Index Sheet ITEM S Bulletin Product Numbering System... 1 Typical Specifi cations, Models 4AC, 4AE, 6AC, 6AE, 8AC... 2 Pump Assembly, Types AC & AE... 3-4 Dimensions, Types AC & AE... 5-8 Selection Curves,

More information

ANSI Centrifugal Process Pumps. 911 Series

ANSI Centrifugal Process Pumps. 911 Series ANSI Centrifugal Process Pumps 9 Series WHAT IS AN ANSI PUMP In 977, the American National Standard Institue (ANSI) established criteria for centrifugal pumps in terms of dimension, chemical composition

More information

PUMP TYPE Single stage, axially split volute casing pump with double entry radial impeller, for horizontal installation.

PUMP TYPE Single stage, axially split volute casing pump with double entry radial impeller, for horizontal installation. SKD SERIES PRODUCT DESCRIPTION AND TECHNICAL DATA PUMP TYPE Single stage, axially split volute casing pump with double entry radial impeller, for horizontal installation. APPLICATION Water supply systems,

More information

Dry installed end-suction pumps, LSN-series. according to ISO 2858 / ISO 5199

Dry installed end-suction pumps, LSN-series. according to ISO 2858 / ISO 5199 Dry installed end-suction pumps, LSN-series according to ISO 2858 / ISO 5199 Technical characteristics Performance 50 Hz 60 Hz Capacity up to 600 m 3 /h 2900 USgpm Head up to 170 m 800 feet Speed up to

More information

Regenerative Turbine Pumps

Regenerative Turbine Pumps Bulletin M M Series Regenerative Turbine Pumps Capacities to 8 GPM Heads to Feet MTH M Series Vertical base mount and horizontal pedestal mounted multi-stage regenerative turbine pumps represent the most

More information

University of Houston Master Construction Specifications Insert Project Name

University of Houston Master Construction Specifications Insert Project Name SECTION 23 30 00 - HVAC PUMPS PART 1 - GENERAL 1.1 RELATED DOCUMENTS: A. The Conditions of the Contract and applicable requirements of Division 1, "General Requirements", and Section 23 01 00, "Mechanical

More information

PWA-LF LOW FLOW ANSI PROCESS PUMP

PWA-LF LOW FLOW ANSI PROCESS PUMP PWA-LF LOW FLOW ANSI PROCESS PUMP COMPETITIVE ADVANTAGES Carbon Steel vs. Ductile Iron n High strength, impact resistant Carbon Steel liquid ends for improved durability and pressure containment at no

More information

PROJ. NO SECTION HYDRONIC PUMPS

PROJ. NO SECTION HYDRONIC PUMPS SECTION 23 21 23 HYDRONIC PUMPS PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 01 Specification Sections,

More information

Series Split Coupled Vertical In-Line Pumps. File no.: 43.10in Date: august 14, 2013 Supersedes: 43.10in Date:

Series Split Coupled Vertical In-Line Pumps. File no.: 43.10in Date: august 14, 2013 Supersedes: 43.10in Date: Series 00 Split Coupled Vertical In-Line Pumps File no.:.0in Date: august, 0 Supersedes:.0in Date: february 0, 0 Series 00 Best commercial hvac pump design available since 99 Life cycle value at every

More information

Bulletin BX-420C Bell & Gossett. VSC /VSCS Pumps Technical Bulletin. Bell & Gossett. Part of the. Equipment Selection Program

Bulletin BX-420C Bell & Gossett. VSC /VSCS Pumps Technical Bulletin. Bell & Gossett. Part of the. Equipment Selection Program Bulletin BX-4C Bell & Gossett VSC /VSCS Pumps Technical Bulletin Part of the Bell & Gossett Equipment Selection Program VSC/VSCS Construction Materials STANDARD SEAL CONFIGURATION PART NAME STANDARD CONSTRUCTION

More information

GH General Horizontal, Close Coupled and Frame Mounted Pumps

GH General Horizontal, Close Coupled and Frame Mounted Pumps GH General Horizontal, Close Coupled and Frame Mounted Pumps Technical Specification Pages This page left intentionally blank. 1.0 Overview. The GH Series is Carver s horizontal, end suction pump for handling

More information

Bulletin C Dean Pump Division. Heavy Duty, High Temperature Process Pumps. R4140 Telescoping Guard. R4140 C-Face Motor Support

Bulletin C Dean Pump Division. Heavy Duty, High Temperature Process Pumps. R4140 Telescoping Guard. R4140 C-Face Motor Support Bulletin C 1.4.43 Dean Pump Division Heavy Duty, High Temperature Process Pumps R4140 Telescoping Guard R4140 C-Face Motor Support Dean Pump Series R Centrifugal Process Pumps Capacities to 5000 GPM (1135

More information

MAXIMUM RECOMMENDED RPM NUMBER OF GUIDE BEARINGS FOR PIT DEPTHS TO 19' - 6" ADDITIONAL HP REQUIREMENTS FOR PUMP WITH INTERMEDIATE GUIDE BEARINGS

MAXIMUM RECOMMENDED RPM NUMBER OF GUIDE BEARINGS FOR PIT DEPTHS TO 19' - 6 ADDITIONAL HP REQUIREMENTS FOR PUMP WITH INTERMEDIATE GUIDE BEARINGS SUSPENDED SOLIDSHANDLING WETPIT PUMPS MAXIMUM RECOMMENDED RPM NUMBER OF BEARINGS FOR PIT DEPTHS TO 9' 6" ADDITIONAL HP REQUIREMENTS FOR PUMP WITH INTERMEDIATE BEARINGS PIT DEPTH 6'0" AND UNDER 6'" TO 0'6"

More information

Series 1510 Centrifugal Pumps

Series 1510 Centrifugal Pumps Series 1 Centrifugal Pumps B-207H Table of Contents Useful Pump Formulas... 2 Standard Features... 3 Technical Data... Materials of Construction... Selection Charts... 6 Performance Curves... 7 Centrifugal

More information

PumPs. jacketed molten sulfur PumPs. Pumps Mixers Strainers Engineered Systems and Controls.

PumPs. jacketed molten sulfur PumPs. Pumps Mixers Strainers Engineered Systems and Controls. Pumps Mixers Strainers Engineered Systems and Controls jacketed molten sulfur PumPs PumPs for molten sulfur and other fluids requiring pumping at controlled temperatures. www.haywardgordon.com introduction

More information

EBARA Submersible Propeller Pumps Contents Project: Model: Chk d: Date: Model

EBARA Submersible Propeller Pumps Contents Project: Model: Chk d: Date: Model Contents Model A0553 C1125 V0494 A0713 C1285 V0554 A0843 C1455 V0754 A03 C15 V0854 C1915 V0974 C2185 V1154 C2905 Section Page Specifications 3-3 Model Designation 3-6 Impeller Data 3-8 Material Specifications

More information

Regenerative Turbine Pumps

Regenerative Turbine Pumps Bulletin 40 October 008 40 40 80 80 Series Regenerative Turbine Pumps Capacities to 60 GPM Heads to 800 Feet MTH PUMPS 40 40 80 80 Series regenerative turbine pumps represent the most economical, high

More information

RS Multi-Stage, Ring Section Pumps

RS Multi-Stage, Ring Section Pumps RS Multi-Stage, Ring Section Pumps Technical Specification Pages This page left intentionally blank. 1.0 Overview. The RS Series is Carver s multi-stage pump for fluids at moderate to high pressures. The

More information

M50 L50 Series Multistage Regenerative Turbine Pumps

M50 L50 Series Multistage Regenerative Turbine Pumps Page M- MTH PUMPS M L Series Multistage Regenerative Turbine Pumps Capacities to 4 GPM Heads to Feet Single or Multi-stage Units (up to stages) Vertical Close Coupled Horizontal Close Coupled Horizontal

More information

Ductile Iron, Jacketed Pumps: Catalog Section 1602 Cast Iron, Non-Jacketed Pumps: Catalog Section 1401 HL4126A

Ductile Iron, Jacketed Pumps: Catalog Section 1602 Cast Iron, Non-Jacketed Pumps: Catalog Section 1401 HL4126A Page 1601.1 TABLE OF CONTENTS Features & Benefits...2 Port Location Options...2 Model Number Key...3 Standard Materials of Construction...3 Cutaway View & Pump Features...4 Special Materials & Options

More information

PWM. API 610 BB3 Multistage Pump

PWM. API 610 BB3 Multistage Pump PWM API 610 BB3 Multistage Pump HYDRAULIC PERFORMANCE COVERAGE FLOW (m 3 /h) 60 Hz Performance Coverage Visit our web site at www.pumpworks610.com and specify flow and performance needs and obtain pump

More information

PWA-LF LOW FLOW ANSI PROCESS PUMP

PWA-LF LOW FLOW ANSI PROCESS PUMP PWA-LF LOW FLOW ANSI PROCESS PUMP COMPETITIVE ADVANTAGES Carbon Steel vs. Ductile Iron n High strength, impact resistant Carbon Steel liquid ends for improved durability and pressure containment at no

More information

PWM APi 610 BB3 Multistage Pump

PWM APi 610 BB3 Multistage Pump PWM APi 610 BB3 Multistage Pump HyDrAUliC PerfOrMAnCe COVerAge FLOW (m 3 /h) 60 Hz Performance Coverage Visit our web site at www.pumpworks610.com and specify flow and performance needs and obtain pump

More information

Trash Hog II Self Priming Solids Handling Centrifugal Pumps

Trash Hog II Self Priming Solids Handling Centrifugal Pumps Trash Hog II Self Priming Solids Handling Centrifugal Pumps Marlow Pumps ITT Industries Trash Hog II A Full Range of Product Features Industrial Duty Power End Provides rigid shaft support. Ample oil

More information

Performance curves. Performance dare To compare

Performance curves. Performance dare To compare Performance curves Performance dare To compare table of contents Pump Size RPM PAGE # 1 1/2 x 1-6AA 1800 1 3600 1 3 x 1 1/2-6AB 1800 1 3600 1 3 x 2-6AC 1800 1 3600 1 LF 1 1/2 x 1-8AA 1800 2 3600 2 1 1/2

More information

Volute Casing Pumps LSN. according to iso 2828 / iso Jansen Pompentechniek T: +31(0) E:

Volute Casing Pumps LSN. according to iso 2828 / iso Jansen Pompentechniek T: +31(0) E: Volute Casing Pumps LSN according to iso 2828 / iso 5199 Technical Data Performance Range: m Capacity up to 500m 3 /h (1980USgpm) m Head up to 150m (492feet) m Speed 2950/3550rpm Pump Sizes: m DN 25 up

More information

ASME END SUCTION PUMPS Catalogue K-90

ASME END SUCTION PUMPS Catalogue K-90 ASME END SUCTION PUMPS Catalogue K-90 ASME B3.1-01 ISO 9001:008 REGISTERED COMPANY Engineered Pumps for Industrial and Municipal Services ASME B3.1 / ANSI END SUCTION PUMPS This catalogue provides the

More information

Application & Reference Data Typical Specifications. Section 914 Vertical Turbine Fire Pump

Application & Reference Data Typical Specifications. Section 914 Vertical Turbine Fire Pump Section 914 Page 101 Supersedes Section 913 Page 101 Dated November 1, 199p Application & Reference Data Typical Specifications Section 914 Section 914 Page 102 Supersedes Section 913 Page 102 Dated November

More information

PWM API 610 BB3 Multistage Pump

PWM API 610 BB3 Multistage Pump PWM API 610 BB Multistage Pump PWM API 610 BB MULTISTAGE PUMP HYDRAULIC PERFORMANCE COVERAGE 60 Hz Performance Coverage FLOW (m /h) Visit our web site at www.pumpworks610.com and specify flow and performance

More information

DSZ3. EBARA Submersible Propeller Pumps Contents Project: Model: Chk d: Date: Model

DSZ3. EBARA Submersible Propeller Pumps Contents Project: Model: Chk d: Date: Model Contents Model A0553 C1125 V0494 A0713 C1285 V0554 A0843 C1455 V0754 A1003 C1605 V0854 C1915 V0974 C2185 V1154 C2905 Section Page Specifications 3-203 Model Designation 3-206 Impeller Data 3-208 Material

More information

Bristol: A History & Future.

Bristol: A History & Future. Fire Pumps Bristol: A History & Future. In 1971, seven emirates joined forces to create the United Arab Emirates, with the goal of becoming a growing leader on an international scale. The UAE s focus has

More information

Bulletin C Dean Pump Division. ANSI/ASME B73.1 Horizontal Process. ph2140 Telescoping Guard. ph2140 C-Face Adapter

Bulletin C Dean Pump Division. ANSI/ASME B73.1 Horizontal Process. ph2140 Telescoping Guard. ph2140 C-Face Adapter Bulletin C 1.2.34.5 Dean Pump Division ANSI/ASME B73.1 Horizontal Process ph2140 Telescoping Guard ph2140 C-Face Adapter Dean Pump Series ph Centrifugal Process Pumps Capacities to 3200 GPM (726 m 3 /hr)

More information

CENTRIFUGAL PUMPS SAE ENGINE DRIVE 10" FEATURES

CENTRIFUGAL PUMPS SAE ENGINE DRIVE 10 FEATURES FEATURES Volute: Heavy ductile iron construction; back pullout design; can be rotated for ease of installation Impeller: Ductile iron enclosed design for high efficiency; superior NPSH characteristics

More information

High Temperature Air-Cooled Hot Oil Pumps

High Temperature Air-Cooled Hot Oil Pumps Bulletin C 1.4.42 Dean Pump Division High Temperature Air-Cooled Hot Oil Pumps No Water Cooling Required RA3 RA2 DEAN PUMP SERIES RA FAN COOLED HIGH TEMPERATURE HOT OIL PUMPS No Liquid Cooling Required

More information

CRANE-DEMING VERTICAL IN-LINE INDUSTRIAL BULLETIN 3180 SECTION 38

CRANE-DEMING VERTICAL IN-LINE INDUSTRIAL BULLETIN 3180 SECTION 38 CRANE-DEMING VERTICAL IN-LINE INDUSTRIAL BULLETIN 3180 SECTION 38 1 ease of installation & maintenance Install like a valve Mount in the pipeline Support on pipe or foundation... Save space - save time

More information

ITT. Goulds Pumps 65L, 95L, 120L, 160L, 250L, 320L 6" Stainless Steel Submersible Pumps. Engineered for life B65-320L. Residential Water Systems

ITT. Goulds Pumps 65L, 95L, 120L, 160L, 250L, 320L 6 Stainless Steel Submersible Pumps. Engineered for life B65-320L. Residential Water Systems B65-32L ITT Residential Water Systems Goulds s 65L, 95L, 12L, 16L, 2L, 32L 6" Stainless Steel Submersible s 6 Hz High Capacity For 6" and larger wells Goulds s is a brand of ITT Corporation. www.goulds.com

More information

Regenerative Turbine Pumps

Regenerative Turbine Pumps Bulletin E4 November 009 E4 T4 Series Regenerative Turbine Pumps Capacities to GPM Heads to 600 Feet Temperatures to 00 F MTH PUMPS MTH E4 T4 Series Close-coupled and pedestal mounted regenerative turbine

More information

CITY OF TAMPA ADDENDUM NO. 2. DATE: June 27, Contract 15-C-00021; Howard F. Curren AWTP HPO Gearbox/Mixer Upgrades and Piping Replacement

CITY OF TAMPA ADDENDUM NO. 2. DATE: June 27, Contract 15-C-00021; Howard F. Curren AWTP HPO Gearbox/Mixer Upgrades and Piping Replacement CITY OF TAMPA Bob Buckhorn, Mayor CONTRACT ADMINISTRATION DEPARTMENT Michael W. Chucran, Director ADDENDUM NO. 2 DATE: June 27, 2016 Contract 15-C-00021; Howard F. Curren AWTP HPO Gearbox/Mixer Upgrades

More information

UNIVERSAL PRODUCT LINE: STEEL EXTERNALS JACKETED PUMPS TABLE OF CONTENTS SERIES DESCRIPTION RELATED PRODUCTS OPERATING RANGE

UNIVERSAL PRODUCT LINE: STEEL EXTERNALS JACKETED PUMPS TABLE OF CONTENTS SERIES DESCRIPTION RELATED PRODUCTS OPERATING RANGE SERIES 4223, 4323 (API 682 Seal) Section 304 Page 304. TABLE OF CONTENTS Features & Benefits...2 Revolvable Pump Casings...2 Materials of Construction...2 Cutaway View & Pump Features...3 Key...4 Specifications...4

More information

TECHNICAL HANDBOOK. Heavy Duty ASME B73.1. Wilfley Sealing Technology. No Flush Water Required

TECHNICAL HANDBOOK. Heavy Duty ASME B73.1. Wilfley Sealing Technology. No Flush Water Required TECHNICAL HANDBOOK Heavy Duty ASME B73.1 A9 Wilfley Sealing Technology No Flush Water Required WILFLEY SEALING TECHNOLOGY Wilfley Sealing Technology is the premier sealing solution for the toughest pumping

More information

Goulds Double Suction Pumps

Goulds Double Suction Pumps Double uction Pumps Designing and Manufacturing Dependable Centrifugal Pumps for Over 125 Years. Model 3498 pumping drinking water through a distribution network in the Western United tates. All 316 stainless

More information

griswold 811 performance curves

griswold 811 performance curves griswold 811 performance curves pump size rpm page # 1 1/2 x 1-6AA 1800 1 3600 1 3 x 1 1/2-6AB 1800 1 3600 1 3 x 2-6AC 1800 1 3600 1 LF 1 1/2 x 1-8AA 1800 2 3600 2 1 1/2 X 1-8AA 1800 2 3600 2 3 X 1 1/2-8AB

More information

3340 Series Single Stage End Suction Pumps

3340 Series Single Stage End Suction Pumps 3340 Series Single Stage End Suction Pumps Bulletin 3340/Rev. A Model 3344 Aurora 3340 Pump Setting New Standards of Efficiency Liquid handling requirements are much more involved than they were five years

More information

Series HSC-S Pumps Technical Brochure

Series HSC-S Pumps Technical Brochure Series HSCS Pumps Technical Brochure BX512L Table of Contents Useful Pump Formulas 2 60 Cycle Performance Curves Series HSCS 3 50 Cycle Performance Curves Series HSCS 4 Series HSCS Materials of Construction

More information

1. Wiring Diagrams: Power, signal, and control wiring.

1. Wiring Diagrams: Power, signal, and control wiring. Page 232123-1 SECTION 232123 - PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 01 Specification Sections,

More information

One & Two Stage Turbine Type Pumps

One & Two Stage Turbine Type Pumps 0A Series APO One & Two Stage Turbine Type Pumps apacities to 0 GPM Heads to 700 Feet Temperatures to 7 F Standard Bronze fitted construction Hydraulically balanced bronze impeller Right- or left-hand

More information

Goulds 3410 Small Capacity Double Suction Pumps

Goulds 3410 Small Capacity Double Suction Pumps Goulds Pumps Goulds 3410 Small Capacity Double Suction Pumps Lenntech info@lenntech.com Tel. +31-152-610-900 www.lenntech.com Fax. +31-152-616-289 Goulds 3410 Double Suction Pumps Designed for a Wide Range

More information

UNIVERSAL PRODUCT LINE: DUCTILE IRON JACKETED PUMPS TABLE OF CONTENTS SERIES DESCRIPTION RELATED PRODUCTS OPERATING RANGE

UNIVERSAL PRODUCT LINE: DUCTILE IRON JACKETED PUMPS TABLE OF CONTENTS SERIES DESCRIPTION RELATED PRODUCTS OPERATING RANGE Page 1602.1 TABLE OF CONTENTS Features & Benefits...2 Porting & Sealing...2 Jacketing...2 Revolvable Pump Casings...2 Cutaway View & Pump Features...3 Model Number Key...4 Standard Materials of Construction...4

More information

Model 133 Models 134 & 135 AURORA 130 SERIES SINGLE STAGE TURBINE TYPE PUMPS

Model 133 Models 134 & 135 AURORA 130 SERIES SINGLE STAGE TURBINE TYPE PUMPS Model Models 4 & AURORA 0 SERIES SINGLE STAGE TURBINE TYPE PUMPS WWW.AURORAPUMP.COM AURORA 0 SERIES Single Stage Turbine Type Pumps Capacities to 0 G.P.M. Heads to 700 Ft. Temperatures to F A Pioneer in

More information

UNIVERSAL PRODUCT LINE: STEEL EXTERNALS JACKETED PUMPS TABLE OF CONTENTS SERIES DESCRIPTION RELATED PRODUCTS OPERATING RANGE

UNIVERSAL PRODUCT LINE: STEEL EXTERNALS JACKETED PUMPS TABLE OF CONTENTS SERIES DESCRIPTION RELATED PRODUCTS OPERATING RANGE SERIES 223A, 4223A, 323A, 4323A Page 1302.1 Issue B TABLE OF CONTENTS Features & Benefits...2 Jacketing...2 Relief Valve Configurations...3 Porting & Sealing...3 Revolvable Pump Casings...3 Cutaway View

More information

CLOSED COUPLED CENTRIFUGAL PUMPS

CLOSED COUPLED CENTRIFUGAL PUMPS SECTION B PAGE 0 ISSUED /0 REPLACES /0 www.pumpagents.com PumpAgents.com - Click here for Pricing/Ordering SERIES: G6--/ thru G9-F 0 Third Street Piqua, Ohio 6-060 CLOSED COUPLED CENTRIFUGAL PUMPS 00RPM

More information

CENTRIFUGAL PROCESS PUMPS MODEL A100 ANSI B73.1

CENTRIFUGAL PROCESS PUMPS MODEL A100 ANSI B73.1 CENTRIFUGAL PROCESS PUMPS MODEL A ANSI B7.1 Heavy Duty Design Features Permit a Wide Range of Process Services All EAGLE A pumps have 1 lb. raised face flanges as standard except 1" and " casings which

More information

D51 D61 D71 D91 Series

D51 D61 D71 D91 Series MTH PUMPS D51 D61 D71 D91 Series Page D-1 Capacities to 24 GPM Heads to 36 Feet Horizontal Close Coupled Close-coupled centrifugal pumps from MTH provide economical performance up to 24 GPM applications

More information

Data sheet. Customer item no.: Communication dated: Number: ES Doc. no.: Item no.: 100 Quantity: 1 Date: 19/03/2015 Page: 1 / 6

Data sheet. Customer item no.: Communication dated: Number: ES Doc. no.: Item no.: 100 Quantity: 1 Date: 19/03/2015 Page: 1 / 6 Data sheet Item no.: Page: 1 / 6 Operating data Operating data determined for maximum inlet pressure Pumped medium Water Clean water Not containing chemical and mechanical substances which affect the materials

More information