* (Electrical entry D or DZ only)

Transcription

1 Pilot pressure (MPa) VNB-TFM92EN-A Instruction Manual VNB-Series, 2 Port Process Valve Solenoid or The intended use of this valve is to control the air in the down-stream pneumatic circuit. according to ISO1389. Refer to specification section for details. 1 Safety Instructions ORIGINAL INSTRUTIONS These safety instructions are intended to prevent hazardous situations and/or equipment damage. These instructions indicate the level of potential hazard with the labels of, or Danger. They are all important notes for safety and must be followed in addition to International s (ISO/IE) *1), and other safety regulations. *1) ISO 1: Pneumatic fluid power - - General rules relating to systems. ISO 13: Hydraulic fluid power - - General rules relating to systems. IE : Safety of machinery - - Electrical equipment of machines. (Part 1: General requirements) ISO : Manipulating industrial robots -Safety. etc. * ( D or DZ only) 1 Safety Instructions continued Only personnel with appropriate training should operate machinery and equipment. The product specified here may become unsafe if handled incorrectly. The assembly, operation and maintenance of machines or equipment including our products must be performed by an operator who is appropriately trained and experienced. Do not service or attempt to remove product and machinery/equipment until safety is confirmed. 1) The inspection and maintenance of machinery/equipment should only be performed after measures to prevent falling or runaway of the driven objects have been confirmed. 2) When the product is to be removed, confirm that the safety measures as mentioned above are implemented and the power from any appropriate source is cut, and read and understand the specific product precautions of all relevant products carefully. 3) Before machinery/equipment is restarted, take measures to prevent unexpected operation and malfunction. ontact SM beforehand and take special consideration of safety measures if the product is to be used in any of the following conditions. 1) onditions and environments outside of the given specifications, or use outdoors or in a place exposed to direct sunlight. 2) Installation on equipment in conjunction with atomic energy, railways, air navigation, space, shipping, vehicles, military, medical treatment, combustions and recreation, or equipment in contact with food and beverages, emergency stop circuits, clutch and brake circuits in press applications, safety equipment or other applications unsuitable for the standard specification described in the product catalogue. 3) An application which could have negative effects on people, property, or animals requiring special safety analysis outside the scope of ISO 1389 described in this document. ) Use in an interlock circuit, which requires the provision of double interlock for possible failure by using a mechanical protective pilot air Air quality VNB to 0.7 MPa Pressure VNB x (Operating pressure) to x (Operating pressure) MPa Note 3) (Refer to Figure 1) Note ) Lubrication Not required (Refer to Section 3.) Temperature -5 to +50 ( type: +60 ) 5 µm filtration or smaller Flow Refer to Table 5, Table 6 Mounting orientation Note 5) Unrestricted 1 VNB2 3 Max. operating 30 times per minute frequency VNB times per minute Min. operating frequency Duty cycle Response time VNB7 15 times per minute Once every 30 days 3 million cycles Please contact SM. Weight Refer to Table 7, Table 8 Vibration resistance 30 m/s 2 Impact resistance 150 m/s 2 s omplies with the basic and well-tried safety principles of ISO :2012 B 10 Note 6) 2 million cycles B 10D Note 6) million cycles Rated Voltage Voltage Tolerance Refer to marking on coil -15% to +10% of rated voltage Polarity Refer to Figure 2, Figure 3 Table 1 Notes: No freezing Note 2) The pressure differential between Port 1 (A) and 2 (B) must not exceed the maximum operating pressure. Note 3) Adjust the operating pressure range from MPa to MPa for low vacuum. 2.3 Specifications: Pilot Solenoid Valve Port size 6A to 25A 32A to 50A SF- -23 VO307-1 Pilot valve SF- DZ D -23-Q VO307- DZ D 1-Q Rated coil voltage (50/60 Hz) Allowable voltage fluctuation Temperature rise Apparent power Power consumption Notes: Inrush Holding Grommet, Grommet terminal, onduit terminal DIN terminal Grommet, DIN terminal 100 V, 200 V, Other voltage (Semi-standard) 2 V, Other voltage (Semi-standard) -15 % to +10 % of rated voltage 35 or less (When 50 or less (When rated voltage is rated voltage is applied.) applied.) 5.6 VA (50 Hz), VA (50 Hz), VA (50 Hz), VA (50 Hz), W (without light), 2 W (without light), W (with light).2 W (with light) -push type push Other (Semi-standard) type Table 3 For How to Order pilot valves, refer to the catalogue. Note 2) Vacuum pilot type pilot valves will become VO301V-00 Note 3) Vacuum pilot type E-compliant pilot valves will become VO307V- D DZ -Q This manual contains essential information for the protection of users and others from possible injury and/or equipment damage. Read this manual before using the product, to ensure correct handling, and read the manuals of related apparatus before use. Keep this manual in a safe place for future reference. To ensure safety of personnel and equipment the safety instructions in this manual must be observed, along with other relevant safety practices. Danger indicates a hazard with a low level of risk which, if not avoided, could result in minor or moderate injury. indicates a hazard with a medium level of risk which, if not avoided, could result in death or serious injury. Danger indicates a hazard with a high level of risk which, if not avoided, will result in death or serious injury. The compatibility of the product is the responsibility of the person who designs the equipment or decides its specifications. Since the product specified here is used under various operating conditions, its compatibility with specific equipment must be decided by the person who designs the equipment or decides its specifications based on necessary analysis and test results. The expected performance and safety assurance of the equipment will be the responsibility of the person who has determined its compatibility with the product. This person should also continuously review all specifications of the product referring to its latest catalogue information, with a view to giving due consideration to any possibility of equipment failure when configuring the equipment. function, and periodical checks to confirm proper operation. Always ensure compliance with relevant safety laws and standards. All electrical work must be carried out in a safe manner by a qualified person in compliance with applicable national regulations. The product is provided for use in manufacturing industries. The product herein described is basically provided for peaceful use in manufacturing industries. If considering using the product in other industries, consult SM beforehand and exchange specifications or a contract if necessary. If anything is unclear, contact your nearest sales branch. 2 Specifications 2.1 General Specifications Series Ambient Temperature Temperature Proof pressure Applicable pressure Note 2) range VNB Water, Oil, Air, Vacuum, etc. (Refer to Table ) -5 to +50 ( type:60 ) VNB A, VNB 1 B -5 to +60 VNB 0 B -5 to +99 (Water, Oil etc. only) VNB 1 VNB MPa Low vacuum to 0.5 MPa Low vacuum to 1 MPa Note ) Lubrication is not allowed in the case of seal material EPR. Note 5) For external pilot, it is recommended that the pilot valve be oriented either vertically upward or horizontally. Note 6) Under SM test conditions. The B 10 figure is estimated from SM life tests. The B 10D figure is derived from B 10 using the assumption in EN ISO :2015Annex. ontact SM for details. Figure Specifications: Vacuum pilot type Vacuum Operating pressure range -101 kpa to Atmospheric pressure Pilot pressure range -101 to -7.9 kpa Table 2 The pilot pressure should be within the range of A against the operating pressure. Operating pressure (MPa) It is used when the valve is to be operated by the main vacuum in the absence of pressurized air. 2. Applicable s heck List Wetted part Body material Wetted part Seal material Air (, Dry) Low vacuum (Up to -101 kpa) arbon dioxide (O2, 0.7 MPa or less) arbon dioxide (O2, 0.7 to 1 MPa) Nitrogen gas (N2) Argon Helium Water (standard, up to 60 ) Water (up to 99 air operated type only) opper alloy: FKM : B Turbine oil Spindle oil Fuel oil lass 3 ( fuel oil) Silicone oil Naphtha Ethylene glycol (up to 80 ) Boiler water Table EPR : Aluminium: L FKM : B EPR : Stainless steel: S FKM EPR : B : Page 1 of 5

2 2.5 Flow characteristics Measured by air Measured by water [dm 3 b v Av x 10-6 m 2 /(bar s)] VNB1-6A VNB1-8A VNB1-10A VNB2-10A VNB2-10A VNB2-15A VNB2-15A VNB3-20A VNB3-20A Table 5 v Effective area (mm 2 ) VNB -25A VNB -25A VNB5-32A VNB5-32A VNB5-32F VNB5-32F VNB6-0A VNB6-0A VNB6-0F VNB6-0F VNB7-50A VNB7-50A VNB7-50F VNB7-50F Table Polarity VNB1 to (Valve size 1 to ) Figure VNB5 to 7 (Valve size 5 to 7), Vacuum pilot type (Valve size 2 to 7) (+,-) (-,+) (+) (-) Vacuum type Valve type Type pilot Normally closed VNB 01 V VNB 11 V Table 10 N.O. Normally open VNB 02 V VNB 12 V Normally opened Return spring *.O. type does not have a return spring VNB 02, 12 (N.O) In contrast with the, when the power to the pilot valve is turned off (or when air is exhausted from the port P2 of the air operated style), the valve is held open by the return spring. When the pilot valve is energised (or when pressurised air enters through the port P2 of the air operated style), the valve element closes. VNB 03 (.O.) The valve element for the.o. type, which has no return spring, is in an arbitrary position when air is exhausted through the ports P1 and P2. When pressurised air enters the port P1 (exhaust from the port P2), the valve element opens and it closes when pressurised air enters the port P2 (exhaust from port P1). Special products might have specifications different from those shown in this section. ontact SM for specific drawings. These drawings will give the appropriate specification details and compliance with the safety principles of ISO 1389, if applicable. 2.6 Port size and Weight Port size Orifice dia. Ø (mm) Air operated Weight (kg) pilot VNB1-6A ⅛ VNB1-8A ¼ VNB1-10A VNB2-10A ⅜ 11 VNB2-10A VNB2-15A 11 ½ VNB2-15A 15 VNB3-20A 1 ¾ VNB3-20A Table 7 Port size Orifice dia. Ø (mm) VNB -25A 16 1 VNB -25A 25 VNB5-32A 22 1¼ VNB5-32A 32 VNB5-32F VNB5-32F 32 VNB6-0A 28 1½ VNB6-0A 0 VNB6-0F 28 0 VNB6-0F 0 VNB7-50A 33 2 VNB7-50A 50 VNB7-50F VNB7-50F 50 Table 8 Air operated Weight (kg) pilot The flange should be JIS B K (ordinary style) or its equivalent. 2.8 s type Type Valve type pilot Figure 3 N.O..O. Normally closed Normally open Double acting VNB 0 1 VNB 1 1 VNB 02 VNB 12 VNB 03 Flow direction should be from port 1(A) to port 2(B) for vacuum applications. Table Working principle Normally closed VNB 0 1, 11 Pilot Solenoid Valve Port 12(P1) Return Spring Piston Assembly Valve Element Port 1(A) Port 10(P2) Port 2(B) When the pilot valve is not energised (or when air is exhausted from the port P1 of the air operated type), the valve element linked to the piston is closed by the return spring. When valve opens: When the pilot valve is energised (or when pressurised air enters through the port P1 of the air operated valve style), the pilot air that has entered the piston moves upward to open the valve element. When valve closes: When the power to the pilot valve is turned off (or when fluid is exhausted from the port P1 of the air operated style), the pilot air under the piston is exhausted, and the return spring closes the valve element 3 Installation 3.1 Installation Do not install the product unless the safety instructions have been read and understood. If it is intended to energize the valve for an extended period of time, please consult SM. If air leakage causes associated equipment to malfunction cease using valve and inspect for cause. heck fixings while pressure and power are applied. Initial function and leakage tests should be performed after installation. Allow sufficient space for maintenance and inspection. Do not paint any part of this product. 3.2 Environment Do not use in an environment where corrosive gases, chemicals, salt water or steam are present. Do not use in an explosive atmosphere. Do not expose to direct sunlight. Use a suitable protective cover. Do not install in a location subject to vibration or impact. heck the product specifications. Do not mount in a location exposed to radiant heat. If this valve is exposed to water or oil droplets, ensure that it is protected. 3.3 Piping Before piping make sure to clean up chips, cutting oil, dust etc. When installing piping or fittings, ensure sealant material does not enter inside the port. When using seal tape, leave 1.5 to 2 threads exposed on the end of the pipe/fitting. Tighten fittings to the specified tightening torque. Page 2 of 5

3 Settings Thread Appropriate tightening torque [N m] ⅛ 7 to 9 ¼ 12 to 1 ⅜ 22 to 2 ½ 28 to 30 ¾ 28 to to 38 1 ¼ 0 to 2 1 ½ 8 to to 50 Table Pilot ports P1 an P2 Pilot port piping 12(P1) and 10(P2) piping should be as follows according to the model. Port VNB 0(1,) VNB 02 VNB 03 VNB 1(1,2,) 12 (P1) pilot Bleed port pilot* pilot 10 (P2) Bleed port pilot pilot* Pilot exhaust *If the pilot air is not supplied, the valve position will not be held. Pressurize Port 12(P1) or Port 10(P2) when using product. Table 12 Vacuum pilot Port VNB 01V VNB 02V VNB 1(1,2)V 12 (P1) Bleed port pilot pilot 10 (P2) pilot Bleed port Pilot exhaust Table 13 If excessive carbon powder is generated, eliminate it by installing mist separators at the upstream side of valves. If excessive carbon powder is generated by the compressor, it may adhere to the inside of the valves and cause malfunction. 3.6 Electrical connection When power is connected to a valve equipped with light and/or surge voltage suppressor, check for polarity indications. For polarity indications: Valve sizes 5 to 7 have diodes to protect polarity: If the polarity connection is wrong then the valve will not switch. In addition to this, damage could be caused in the diode in the valve, the switching device at the control equipment or, the power supply DIN onnector (see Figure 5) Loosen the fixing screw and remove the connector housing from the terminal spades on the. Remove the housing screw and insert a screwdriver into the slot on the underside of the DIN cap and carefully remove the block. Insert the cable through the gland nut, washer, grommet and housing. Loosen the terminal screws on the block and insert the stripped ends of the leads. Secure each lead by re-tightening the appropriate terminal screw. Tighten the housing gland nut to secure the cable. Reassemble the DIN connector in reverse order of removal. onnections for DIN connector are shown below; Valve series 1, 2, 3 and can be mounted using a bracket (optional) VNB1 Pilot port 2-1/8 (Back side P2) Figure 6 2-Ø.5 Bracket Main port 2-2-Mx0.7 depth 7.1 Manual Override Ensure conditions are safe, since connected equipment will operate when manual override is performed..1.1 push type VNB1- Push on the manual override button using a small bladed screwdriver until it stops ON. Hold this position for the duration of the check (ON position). See Figure 9, Release the button and the override will re-set to OFF position VNB5-7 No tool needed. See Figure 10 Push type Push type push type Figure 9 Installing a silencer to the exhaust port and the bleed port is recommended for noise reduction and for dust entry prevention. Figure 7 Figure 10 Port 12 (P1) Port 10 (P2) (If available) Port 2 (B) DIN onnector Gland nut Grommet Washer Fixing screw Housing Pilot port 2-1/8 (Back side P2) VNB2~ -ØP.1.2 Push-locking slotted type (see Figure 11) To lock Using a small-bladed screwdriver in the slot, push the manual override button until it stops. Turn the override button 90 in the direction of the arrow until it stops (ON position). Remove the screwdriver 3. Lubrication Figure SM products have been lubricated for life at manufacture, and do not require lubrication in service. If a lubricant is used in the system, use turbine oil lass 1 (no additive), ISO VG32. Once lubricant is used in the system, lubrication must be continued because the original lubricant applied during manufacturing will be washed away. 3.5 Air supply When extremely dry air is used as the fluid, degradation of the lubrication properties inside the equipment may occur, resulting in reduced reliability (or reduced service life) of the equipment. Please contact SM. Install an air filter Install an air filter upstream near the valve. Select an air filter with a filtration size of 5 μm or smaller. Take measures to ensure air quality, such as by installing an aftercooler, air dryer, or water separator. ompressed air that contains a large amount of drainage can cause malfunction of pneumatic equipment such as valves. Therefore, take appropriate measures to ensure air quality, such as by providing an aftercooler, air dryer or water separator. Ground 3.7 Mounting Figure 5 Block Do not apply external force to the coil section. When tightening is performed, apply a wrench or other tool to the outside of the piping connection parts. Mount a valve with its coil position upwards, not downwards. When mounting a valve with its coil positioned downwards, foreign objects in the fluid will adhere to the iron core leading to malfunction. Especially for strict leakage control, such as with vacuum applications and non-leak specifications, the coil must be positioned upwards. Main port 2- Figure 8 Main port M N P R S U VNB21-10A ⅜ VNB21-15A ½ VNB21-20A ¾ VNB21-25A Table 1 Thread Appropriate tightening torque [N m] M 1.5 M5 3.0 M6 5.2 Table 15 Bracket In this position the manual override is in the locked ON position. To unlock Place a small-bladed screwdriver in the slot and push the manual override button. Turn the override button 90 in the reverse direction of the arrow. Remove the screwdriver and the manual override will reset to the OFF position. Twist locking, Slotted type Figure 11 Page 3 of 5

4 5 How to Order 6 Outline Dimensions (mm) Valve size Valve type Port size Orifice dia. (mm) N.O..O. 1 MPa 1 MPa 0.5 MPa 1 MPa Port size 6A 1/8 1 Ø7 8A 1/ 10A 3/8 2 Ø11 Ø15 10A 3/8 Ø11 Ø15 15A 1/2 3 Ø1 Ø20 20A 3/ Ø16 Ø25 25A Seal material A seals B FKM seals EPR seals pilot Ø22 Ø32 Ø22 Ø32 Ø28 Ø0 Ø28 Ø0 Ø33 Ø50 Ø33 Ø50 32A 1 1/ 32F 1 1/ B 0A 1 1/2 0F 1 1/2 B 50A 2 50F 2B only Note 2) The valve type symbols for vacuum pilot type are 1 () and 2 (N.O.) only. Nil Body material option S* Stainless steel body L* Aluminum body *Threaded port only Rated voltage /With light/surge voltage suppressor Valve size Valve size 1 to 5 to 7 G Grommet GS Grommet with surge voltage suppressor E Grommet terminal EZ Grommet terminal with light/surge voltage suppressor T onduit terminal TZ onduit terminal with light/surge voltage suppressor D DIN terminal DZ DIN terminal with light/surge voltage suppressor E-compliant V 50/60 Hz V 50/60 Hz 3 Note 2) 110 V 50/60 Hz Note 2) 220 V 50/60 Hz 5 2 V 6 Note 2) 12 V 7 Note 2) 20 V 50/60 Hz : D or DZ only. Note 2) Semi-standard Note 3) For other rated voltages, please consult with SM. Pilot system option Nil V Vacuum pilot type V is for vacuum pilot valve specification, for both main pressure and pilot pressure, valve size 2 to 7. VNB A 15A Thread type Nil F G N NPT T NPTF VNB A 15A 1 T Valve size 1 to Valve size 5 to 7 Nil: Nonlocking push type D DIN terminal DZ DIN terminal with light/surge voltage suppressor E-compliant Nil Q E-compliant * * : D or DZ only Valve size 1 to A: push type A (projecting) B: Slotted locking type B (tool required) Semi-standard Bracket (Valve size: 1/2/3/) Nil None B With bracket Only valve sizes 1, 2, 3 and. Shipped after assembled at our factory. Bracket part no. Valve size 1: VN1-A16 (with thread) Valve sizes 2 to : VN to Valve size 5 to 7 Nil: push type Refer to the catalogue. 7 Maintenance 7.1 General Maintenance Not following proper maintenance procedures could cause the product to malfunction and lead to equipment damage. If handled improperly, compressed air can be dangerous. Maintenance of pneumatic systems should be performed only by qualified personnel. Before performing maintenance, turn off the power supply and be sure to cut off the supply pressure. onfirm that the air is released to atmosphere. After installation and maintenance, apply operating pressure and power to the equipment and perform appropriate functional and leakage tests to make sure the equipment is installed correctly. If any electrical connections are disturbed during maintenance, ensure they are reconnected correctly and safety checks are carried out as required to ensure continued compliance with applicable national regulations. Do not make any modification to the product. Do not disassemble the product, unless required by installation or maintenance instructions. Vacuum Pilot: When using VNB 0 1 1V vacuum pilot, maintain the specified pilot pressure by providing a tank with an appropriate capacity or by acquiring the pilot pressure from an area near the vacuum pump. Filters and strainers: Be careful regarding clogging of filters and strainers. Replace filter elements after one year of use, or earlier, if the pressure drop reaches 0.1 MPa lean strainers when the pressure drop reaches 0.1 MPa. Storage: In case of long term storage after use with heated water, thoroughly remove all moisture to prevent corrosion, and deterioration of rubber materials etc. Drain flushing: Remove drainage from air filters regularly. (Refer to the specifications) Page of 5

5 7 Maintenance - continued 8 Limitations of Use 7.2 Replacing Spare Parts Mounting Screw 8.1 Limited warranty and Disclaimer/ompliance Requirements The product used is subject to the following Limited warranty and Disclaimer and ompliance Requirements. Read and accept them before using the product. Pilot Valve Mounting Screw (over) Piston, over Plate Assembly Valve Element Nut Body Figure 12 Limited warranty and Disclaimer 1) The warranty period of the product is 1 year in service or 1.5 years after the product is delivered, whichever is first (1). Also, the product may have specified durability, running distance or replacement parts. Please consult your nearest sales branch. 2) For any failure or damage reported within the warranty period which is clearly our responsibility, a replacement product or necessary parts will be provided. This limited warranty applies only to our product independently, and not to any other damage incurred due to the failure of the product. 3) Prior to using SM products, please read and understand the warranty terms and disclaimers noted in the specified catalogue for the particular products. (1) Vacuum pads are excluded from this 1 year warranty. A vacuum pad is a consumable part, so it is warranted for a year after it is delivered. Also, even within the warranty period, the wear of a product due to the use of the vacuum pad or failure due to the deterioration of rubber material are not covered by the limited warranty. ompliance Requirements 1) The use of SM products with production equipment for the manufacture of weapons of mass destruction (WMD) or any other weapon is strictly prohibited. 2) The exports of SM products or technology from one country to another are governed by the relevant security laws and regulations of the countries involved in the transaction. Prior to the shipment of a SM product to another country, assure that all local rules governing that export are known and followed. 9 ontacts AUSTRIA BELGIUM BULGARIA ROATIA ZEH REP. DENMARK ESTONIA FINLAND FRANE GERMANY GREEE HUNGARY IRELAND ITALY LATVIA SM Pneumatik GmbH,Girakstrasse 8, AT-2100 Korneuburg, Austria SM Pneumatics N.V. S.A. Nijverheidsstraat 20, B-2160 Wommelgem, Belgium SM Industrial Automation Bulgaria EOOD, Business Park Sofia, Building 8-6th floor, BG-1715 Sofia, Bulgaria SM IndustrijskaAutomatikad.o.o. ZagrebačkaAvenija 10, Zagreb SM Industrial Automation Z s.r.o. Hudcova 78a, Z Brno, zech Republic SM Pneumatik A S,Egeskovvej 1, DK-8700 Horsens, Denmark SM Pneumatics Estonia Oü,Laki 12, EE Tallinn, Estonia SM Pneumatics Finland Oy, PL72, Tiistinniityntie, SF Espoo, Finland SM Pneumatique SA.1, Boulevard de Strasbourg, Parc Gustave Eiffel, Bussy Saint Georges, F Marne La Valleeedex 3, France SM Pneumatik GmbH, Boschring 13-15, Egelsbach, Germany SM Italia Hellas Branch, Anagenniseos 7-9-P N.Philadelphia, Athens, Greece SM Hungary IpariAutomatizálásiKft.Torbágy u. 19, HU- 205 Törökbálint, Hungary SM Pneumatics (Ireland) Ltd.2002 itywest Business ampus, Naas Road, Saggart, o. Dublin, Ireland SM Italia S.p.A.Via Garibaldi 62, I-20061arugate, (Milano), Italy SM Pneumatics Latvia SIA, Dzelzavas str. 120g, Riga, LV-1021, Latvia Replacing Plate Assembly and valve element (see Figure 12) 1. Remove body mounting screws. 2. Apply sufficient air pressure to pilot port to release plate assembly. 3. Place well-fitting slotted screwdriver into slot in piston rod and unscrew seal mounting nut with spanner.. If spring pin is used, slide pin out and remove valve element. 5. Slide off valve element, washers and plate assembly. 6. Refitting is reverse of removal (use correct tightening torque) Replacing Pilot Valve Assembly (see Figure 12) 1. Remove pilot valve mounting screws. 2. Remove pilot valve (retain DIN plug if necessary). 3. Fitting of new pilot valve is reverse of removal assembly (use correct tightening torque). Never remove inner circlip from valve. When replacing external pilot valve, ensure it is mounted in the correct direction. If mounted in the wrong direction, it may malfunction or leak air. Tightening Torque (N m) Valve size VNB1 VNB2 VNB3 VNB VNB5 VNB6 VNB7 Seal Mounting Nut Piston over Mounting Screw Pilot Valve Mounting Screw Table 16 SM products are not intended for use as instruments for legal metrology. Measurement instruments that SM manufactures or sells have not been qualified by type approval tests relevant to the metrology (measurement) laws of each country. Therefore, SM products cannot be used for business or certification ordained by the metrology (measurement) laws of each country. Do not exceed any of the specifications laid out in section 2 of this document or the specific product catalogue. Danger Any use in an EN ISO 1389 system must be within the specified limits and application condition. The user is responsible for the specification, design, implementation, validation and maintenance of the safety system (SRP/S). LITHUANIA NETHERLANDS NORWAY POLAND PORTUGAL ROMANIA RUSSIA SLOVAKIA SLOVENIA SPAIN SWEDEN SWITZERLAND TURKEY UK UAB SM Pneumatics, Oslo g. 1, LT-0123 Vilnius, Lithuania SM Pneumatics B.V.De Ruyterkade 120, NL-1011 AB Amsterdam, the Netherlands SM Pneumatics Norway AS, Vollsveien 13, GranfosNæringspark, N-1366 Lysaker, Norway SM Industrial Automation, Polska Sp z o.o Warszawa, ul. Poloneza 89, Poland SM España S.A. Zuazobidea 1, Vitoria, Spain SM Romania S.r.l. StrFrunzei 29, Sector 2, Bucharest, Romania SM Pneumatik LL. Business centre, building 3, 15 Kondratjevskij prospect, St.Petersburg, Russia, SM PriemyselnáAutomatizáciaSpols.r.o. Fantranská 1223, Teplickanadvahom, 01301, Slovakia SM IndustrijskaAvtomatikad.o.o. Mirnskacesta 7, SLO Trebnje, Slovenia SM España S.A. Zuazobidea 1, Vitoria, Spain SM Pneumatics Sweden AB,Ekhagsvägen 29-31, SE Segeltorp, Sweden SM Pneumatik AG,Dorfstrasse 7, Postfach, 88 Weisslingen, Switzerland SM PnömatikSanayiTicaretveServis A.Ş. Gülbaharaddesi, Aydın Plaza, No: 9 Güneşli 3212, Istanbul SM Pneumatics (U.K.) Ltd. Vincent Avenue, rownhill, Milton Keynes, Buckinghamshire MK8 0AN, United Kingdom URL : http// (Global) http// (Europe) 'SM orporation, Akihabara UDX15F, -1-1, Sotokanda, hiyoda-ku, Tokyo Specifications are subject to change without prior notice from the manufacturer SM orporation All Rights Reserved. Template DKP5007-F-085D Page 5 of 5