998 Spare Parts Book. McHale, Ballinrobe, Co. Mayo, Ireland. Tel: Fax: Website:

Transcription

1 998 Spare Parts Book McHale, Ballinrobe, Co. Mayo, Ireland. Tel: Fax: Website:

2 This page is intentionally left blank

3 Introduction The which you have purchased has been developed through years of constant research and development. Given proper care and attention the 998 will give years of reliable and dependable performance. However it is important that the operators manual is read and fully understood to achieve this, before the machine is operated. As part of this philosophy it is vital to use only genuine McHale replacement parts, as these are manufactured to the same high standard as the original machine. These may be obtained through your McHale dealer. Ifanypartofthismanualisnotfullyunderstood,pleasecontactyour McHaledealerwhowillbeabletoansweranyquestionsorqueries that you might have. It is important to quote the machine serial number when requiring spare parts or technical assistance. Space is provided below to record the machine details: Serial number: Year of manufacture: Date of delivery: If you require further copies of this spare parts manual please quote part number CLT7 Note: Parts described as left and right are done so according to the direction that the machine normally travels in. Note: Due to a policy of continuous product development and improvement McHale Engineering reserve the right to alter machine specifications without prior notice.

4 Contents Section Page No Document No Section Page No Document No Chassis Chassis (35) Stub axles & Wheels (37) Arch (38) Dispenser arm (39) Dispenser drive (3) Dispenser (3) Cut & Hold back plate (3) Cut & Hold slider (33) Unloading roller (3) Unloading roller table (585) Cradle arm (35) SPD35 SPD37 SPD38 SPD39 SPD3 SPD3 SPD3 SPD33 SPD3 SPD585 SPD35 Air brake kit 998 up to & incl 8 (37) Air brake kit 998 from 9 onwards (9) Electrical components [Up to Serial No 567] (3) Electrical components [Serial No 568 to 587] (33) Electrical components [From Serial No 588] (797) Electrical lighting (3) Remote control options (63) Decals Decals (35) SPD37 SPD9 SPD3 SPD33 SPD797 SPD3 SPD63 SPD35 Rollers (37) 8 SPD37 Drawbar (38) 3 SPD38 Headstock (39) 3 SPD39 PTO shaft (33) 3 SPD33 Hydraulic tank (33) 36 SPD33 Main conveyor main drive (33) 38 SPD33 Bale position sensor arms (33) SPD33 Front conveyor (335) SPD335 Spare film holder (337) SPD337 Round bale kit (36) 6 SPD36 Small bale kit (38) 8 SPD38 Hydraulic & Electrical Hydraulic control valve (338) 5 SPD338 Hydraulic valve roller rotation (339) 5 SPD339 Hydraulic valve dispenser drive (3) 5 SPD3 Hydraulic pipes steel (3) 56 SPD3

5 This page is intentionally left blank

6 Chassis (35) Page 6 SPD35

7 No. Part No Description Qty No. Part No Description Qty ACH CHASSIS 38 CFA35 NUT, M PLAIN Z/P CMH9 BOTTOM RUNNER STRIP (WOOD) 39 ACH39 MAIN CONVEYOR ADJUSTER BOLT 3 CFA7 SETSCREW, Mx3 CUP SQUARE Z/P 6 CZB8 HYDRAULIC VALVES INNER COVER CMH39 CHAIN GUIDE (WOOD) CFA3 SETSCREW, Mx Z/P 9 5 CFA89 BOLT, Mx3 CUP SQUARE Z/P CZF33 INSPECTION COVER 6 CFA38 WASHER, mm FLAT 7 3 ACH HYDRAULIC VALVES REAR COVER 7 CFA NUT, M NYLOC 8 5 CFA5 WASHER, mm SKM 6 8 CZD79 CONVEYOR BOTTOM RUNNER LIP RIGHT 6 CFA9 SETSCREW, M8x SOCKET CAP 6 8 CZD CONVEYOR BOTTOM RUNNER LIP LEFT 7 CZB7 HYDRAULIC VALVES OUTER COVER 9 CFA3 NUT, M NYLOC 8 CFA33 SETSCREW Mx35 Z/P CFA6 NUT, M NYLOC 9 CFA5 WASHER, mm SKM CFA3 NUT, M8 NYLOC 8 5 CFA7 WASHER, mm SPRING CFA5 SETSCREW, M8x Z/P 8 5 ADB DRAWBAR MAIN PIVOT PIN CAP 3 CZD35 FRONT LIGHT BRACKET 5 CMH59 DRAWBAR MAIN PIVOT PIN CFA9 SETSCREW, Mx3 CSK HEX 53 CZF5 WASHER, x85x6 5 CMH7 SHORT WEAR STRIP (PLASTIC) 5 CFA7 BOLT Mx6 Z/P 6 CMH6 LONG WEAR STRIP (PLASTIC) 55 CHY3 ADAPTER, /"-/" 7 CFA3 SETSCREW, Mx BUTTON HEAD 88 FROM SERIAL NO ACH37 MAIN CONV. CHAIN COMPLETE (9,7,8,9) 56 CZD CHAIN RUNNER FROM SERIAL NO CCH MAIN CONV. SINGLE CHAIN C/W JOINER 57 CMH3 BOTTOM BALE LIFT CYLINDER PIN 8 CCH8 JOINER LINK CMH7 MAIN CONVEYOR REAR DRIVE HINGE PIN 8 CCH INNER LINK (ATTACHMENT) ACH53 CHAIN DOWN CLAMP AS REQUIRED 9 CZC FROM SERIAL NO. 9 9 CZC7 UP TO SERIAL NO CFA3 ACH38 CRA8 CSE8 CRA88 CRA89 3 CFA CMH76 5 CMH7 6 CBE 7 CVA3 8 ACH5 9 CFA 3 CFA37 3 ACH 3 CFA8 33 CMH87 3 CHY UP TO SERIAL NO CHY8 UP TO SERIAL NO CHY53 37 CVA3 Page 7 CONVEYOR SLAT 7 CONVEYOR SLAT 7 SETSCREW, Mx5 Z/P 6 HYDRAULIC HOSE TRAY CONVEYOR LIFT CYLINDER COMPLETE LIFT CYLINDER SEAL KIT LIFT CYLINDER ROD LIFT CYLINDER GLAND ROLL PIN, 8x5 Z/P LIFT CYLINDER REAR PIVOT PIN DRAWBAR CYLINDER REAR PIVOT PIN RUBBER BUFFER HYDRAULIC ACCUMULATOR, 3 BAR REAR LIGHT BRACKET SETSCREW, Mx5 Z/P 6 WASHER, mm SPRING 8 CRADLE PIVOT PIN GREASE NIPPLE, M8 STRAIGHT SLOTTED LINK TOP PIN WASHER, 3/8" "DOWTY" ADAPTER, 3/8"-/" WASHER, /" "DOWTY" HYDRAULIC ACCUMULATOR, 7 BAR UP TO SERIAL NO. 955 CTP6 WHEEL CHOCK FROM SERIAL NO. 57 CTP7 WHEEL CHOCK BRACKET FROM SERIAL NO. 57 SPD35

8 Stub axles & Wheels (37) Page 8 SPD37

9 No. Part No Description Qty No. Part No Description Qty CAX STUB AXLE, COMPLETE (HYD + AIR) LEFT LH CAX3 STUB AXLE, COMPLETE (HYD + AIR) RIGHT RH CRA BRAKE OPERATING CYLINDER (HYD) CFA7 BOLT Mx6 Z/P 3 CAX8 BRAKE OPERATING LEVER CFA8 NUT M PLAIN 5 CFA9 NUT M NYLOC 6 6 CFA3 SETSCREW, Mx5 Z/P 6 7 CAX9 BRAKE SHOES (SET)(FAD) FAD 8 ACH7 BEARING KIT ( BEARINGS & SEAL) ADR ADR 8 ACH8 BEARING KIT ( BEARINGS & SEAL) FAD FAD 9 CFA35 WHEEL STUD M8X.5 (FAD) 6 CAX HUB (BRAKED) CWH7 WHEEL COMPLETE (6/7-) CWH WHEEL CENTRE (x) CWH6 TYRE (6/7-) 3 CFA WHEEL NUT 6 CAX HUB NUT (ADR) ADR CAX3 HUB NUT (FAD) FAD 5 CAX HUB CAP (ADR) ADR 5 CAX5 HUB CAP (FAD) FAD 6 CSE HUB SEAL (ADR) ADR 6 CSE7 HUB SEAL (FAD) FAD Page 9 SPD37

10 Arch (38) Page SPD38

11 No. Part No Description Qty No. Part No Description Qty ACH ARCH CZF33 INSPECTION COVER 3 CFA3 SETSCREW, Mx Z/P CFA37 WASHER, MM SPRING 5 CFA5 SETSCREW, M6x Z/P 6 6 CFA8 NUT, M6 NYLOC 6 7 ACH TOP ARM 8 CFA3 SETSCREW Mx5 Z/P 9 CFA39 WASHER M SPRING Z/P 6 CMH7 DOWEL Z/P ATR8 TOP REDUCTION GUIDE CFA SETSCREW M8x5 Z/P 3 CFA3 NUT M8 NYLOC CZF63 SENSOR PLATE 5 CFA36 BOLT M8x3 Z/P 6 CFA9 WASHER SKM8 7 CFA38 BOLT M X 5 Z/P 6 8 CFA9 M8 X SOCKET HEAD BOLT 9 CFA9 WASHER SKM8 CFA5 WASHER SKM CHY7 STEEL HYDRAULIC PIPE ASSEMBLY Page SPD38

12 Dispenser arm (39) Page SPD39

13 No. Part No Description Qty No. Part No Description Qty ADP57 DISPENSER BCK ASSY ADP7 DISP ARM WELDCENTRE ADP97 TRIP ARM TUBE HOLDER ADP6 998 TRIP ARM MESH HOLDER BRACKET 5 CBC5 CAP PLAS INSERT ROUND.MM 6 CEL7 MAGNET BLUE WHEEL 7 CEL6 BUSH SNAP 8.X3 NYLON 8 CEL9 SWITCH LIMIT 9 CFA SETSCREW MX5 Z/P CFA8 BOLT MX65 Z/P CFA5 SETSCREW M8X Z/P CFA99 SETSCREW M6X Z/P 3 CFA3 NUT M NYLOC CFA5 NUT M Z/P 5 CFA8 NUT M6 NYLOC 6 6 CFA9 NUT M NYLOC 7 CFA3 NUT M6 NYLOC 8 CFA WASHER FLAT 6MM Z/P 6 9 CFA WASHER FLAT 6MM Z/P CFA7 WASHER FLAT 8MM Z/P CFA WASHER FLAT MM Z/P CFA9 BOLT M6X Z/P 6 3 CFA5 WASHER SKM CFA97 BOLT MX Z/P 5 CFA3 SETSCREW M5X Z/P 6 CFA3 WASHER FLAT 5MM 7 CFA3 NUT M5 NYLOC 8 CFA383 BOLT MX7 Z/P 9 CFA77 TURNBUCKLE EYE MM 3 CFA86 SETSCREW MX35 Z/P 3 CGD8 DISPENSER SAFETY ARM ALUMINIUM 3 CGD SAFETY ARM DISPENSER 998 PRE USED PRE. REPLACED BY CGD8 3 CGD9 DISPENSER 998 YELLOW PVC 33 CPL8 INSULATION SAFETY BAR 3 CSG3 SPRING TRIP ARM 6.35XX8 35 CXB8 BX 8X8X6 ALUMINIUM BENT9 36 CZB5.5MM L DISPENSER LOOM COVER COMBI 37 CZF356 6MM L DISPENSER ARM ASSY 38 CZF55 6MM L PLATE 39 CZF553 6MM L PLATE CZF5555 6MM L BRACKET 998 CZH8 MM L BALE HANDLER 6 Page 3 SPD39

14 Dispenser drive (3) Page SPD3

15 No. Part No Description Qty No. Part No Description Qty CMT33 GEARBOX DISPENSER ROTATION CMT35 GEARBOX SHAFT TOP/REDU.C 3 CBR8 BEARING6I CMH GEARSPURCOMBIGEARBOX 5 CMH9 GEAR SPUR XM T COMBI GEARBOX 6 CBR7 BEARINGSNR6OIO 7 CFA NUTCOMBIGEARBOX 8 CSE95 SEAL GEARBOX COMBI 9 CMT GEAR BOX COVER PLATE COMBI CFA5 SETSCREWMIOX3O 3 CFA WASHER 39X7X6 CFA5 GRUBSCREW M8XIO 3 CMT BRAKE UNIT HYDRAULIC UP TO SERIAL NO REP5 REPAIR KIT 998 MOTOR + BRAKE SERIAL NO. 56 TO CMT6 BRAKE UNIT HYDRAULIC FROM SERIAL NO. 599 CZF358 6MM L SENSOR BRACKET COMBI 5 CZD7 MM L SENSOR GUARD COMBI 6 CFA9 WASHER SKM I 8 7 CFA398 SETSCREW MIX3O ZIP 8 8 CZH IOMMLWASHERI5X3OXIO 9 CZD66 MM L WASHER I X5X CFA9 WASHER SKM8 CFA SETSCREW M8X5 ZIP CFA76 SETSCREW MI X3 FLD ZP 3 ADP8 TOP MOTOR&VALVE ASY 998 CHAIN UP TO SERIAL NO ADP97 TOP MOTOR&VALVE ASY 998 GEAR SERIAL NO. 56 TO REP5 REPAIR KIT 998 MOTOR + BRAKE SERIAL NO. 536 TO CMT5 MOTOR CC TF 3 SHAFT FROM SERIAL NO. 599 ADP8 TOP MOTOR&VALVE ASY 998 CHAIN UP TO SERIAL NO. 559 ADP97 TOP MOTOR&VALVE ASY 998 GEAR SERIAL NO. 56 TO 535 CVA53 VALVE ASY ARM ROTATION 9983 FROM SERIAL NO CMH756 BUSH IXX 6 CFA535 BOLTMIX5OSOC 7 CEL6 ASY SLIPRING WAY BOTTOM 8 CEL7 SLIPRING ROTARY CON WAY 9 CEL5 CON ASY SLIPRING WAY TOP 3 CSE7 SEAL -RING I8X NBR 8 3 CFA58 BOLT M8 X 7 SOC CAP ZP 3 CFA3 NUT M8 NYLOC Z/P 33 CSE SEALKITFORTESERIESMOTORS 3 CSE SEAL KIT BRAKE UNIT BTM MODEL Page 5 SPD3

16 Dispenser (3) Page 6 SPD3

17 No. Part No Description Qty No. Part No Description Qty ADP86 DISPENSER ASSEMBLY COMPLETE CEL TRANSMITTER EVEN/GEAR COVER CEL TRANSMITTER ODD/GEAR COVER a CZH97 MM L DISPENSER CAP SPACER CFA85 WASHER SPRING 8MM Z/P 3 CFA SETSCREW M8x5 Z/P CFA NUT M NYLOC 3 5 CFA39 WASHER FLAT MM HD Z/P 6 ADP KIT DISPENSER GEARS 6% 6% 6 ADP9 KIT DISPENSER GEARS 55% 55% 8 CFA5 SETSCREW M8x Z/P 8 9 CBR BEARING SLFL CFA53 KEY 6x6x5 CFA3 NUT M8 NYLOC Z/P 8 CZD DISPENSER SPACER 3 CMH3 ROLLER DISPENSER PRIMARY CMH35 ROLLER DISPENSER SECONDARY 5 CFA SETSCREW Mx5 Z/P 6 CFA37 WASHER SPRING MM HD Z/P 7 CZD8 CUT AND TIE SPACER 8 CMH69 PIN 3x8 STEPPED Z/P (75mm FILM) 8 CMH66 PIN 3x535 STEPPED Z/P (5mm FILM) 9 ADP DISPENSER FILM HOLDER ASSEMBLY CSG3 SPRING TOR. 6.35WDx8Dx7.8 COIL CSG SPRING COMP.65x6xx8 CMH97 PIN 6x8 STEPPED Z/P CFA8 GRUBSCREW M6x6 Z/P 3 CFA ROLL PIN 8x5 Z/P CBR68 BEARING 3x3x6 STEPPED PLAS 5 CFA35 WASHER FLAT Z/P 6 CSG9 SPRING COMP.95x37x97x 7 CZC DISPENSER SPACER 8 CBR9 BEARING 65RS 9 CMH87 COIL ROLLER ( BEARING TYPE) 3 CFA CIRCLIP 5MM EXTERNAL Z/P 3 CFA3 SETSCREW Mx3 Z/P 3 CSG3 SPRING EXT..83xx65x.5 33 CZH65 DISPENSER HANDLE PART 3 CBC CAP PLASTIC HANDGRIP 7/8 35 CFA CABLE ROLLER RELEASE ADP5 DISPENSER MAIN FRAME Page 7 SPD3

18 Cut & Hold back plate (3) Page 8 SPD3

19 No. Part No Description Qty No. Part No Description Qty ACT CUT & HOLD COMPLETE CFA NUT M NYLOC 9 CFA39 WASHER MM FLAT (H/D) 6 3 CZD55 BACKPLATE CMH6 ECCENTRIC BEARING HOLDER 5 CMH6 CONCENTRIC BEARING HOLDER 6 CBR BEARING 6RS 3 7 CFA7 SETSCREW Mx5 Z/P 8 CFA7 BOLT Mx5 Z/P 9 CFA69 SETSCREW M6x Z/P CFA68 WASHER 6MM SHAKEPROOF CZC KNIFE CLAMP CBE BUFFER RUBBER 3 CZD8 WASHER xx CSG SPRING PLUNGER 5 CKN KNIFE 6 CZF KNIFE PLATE 7 CFA WASHER 6MM FLAT 8 CFA98 SETSCREW M6x5 Z/P 9 ACT3 PLUNGER BRACKET CFA8 GREASE NIPPLE M8 STRAIGHT CFA3 SETSCREW Mx3 Z/P CBR6 BUSH OILITE 3 CMH3 PLUNGER CHROME CFA37 WASHER MM SPRING 5 CFA SETSCREW Mx5 Z/P 6 CFA3 SETSCREW Mx5 Z/P 7 CFA3 NUT M6 NYLOC 8 CZH9 WASHER XX Page 9 SPD3

20 Cut & Hold slider (33) Page SPD33

21 No. Part No Description Qty No. Part No Description Qty ACT SLIDER BARE (ALUM RAIL TYPE) FROM SERIAL NO. 95 ACT SLIDER (STEEL RAIL) UP TO SERIAL NO. 99 CMH6 RAIL (ALUMINIUM) FROM SERIAL NO CFA89 SETSCREW M8x5 CSK HEX Z/P 5 FROM SERIAL NO CFA36 SETSCREW M8x CSK HEX SS 5 UP TO SERIAL NO. 95 CFA6 NUT M NYLOC 5 CMH33 WASHER RAM DISHED 6 CMH33 WASHER RAM RUBBER 7 CFA NUT / UNF NYLOC 8 CRA7 CUT & HOLD CYLINDER COMPLETE 8 CSE7 SEAL KIT CUT & HOLD CYLINDER 8 CRA3 CYLINDER ROD (TOP) 8 CRA CYLINDER ROD (BOTTOM) 8 CRA5 CYLINDER GLAND (TOP) 8 CRA6 CYLINDER GLAND (BOTTOM) 8 CRA CYLINDER PISTON (TOP) 8 CRA CYLINDER PISTON (BOTTOM) 9 CFA3 NUT M8 NYLOC 7 FROM SERIAL NO. 955 CFA7 WASHER 8MM FLAT 6 FROM SERIAL NO. 955 ALA88 KIT - CUT & HOLD RAIL 998 ROD IRON KIT INCLUDES ITEMS 9,, 3, & 5 CPL9 TUBE.X7.8X5 PVC CONDUIT 3 CPL TUBE 5XX7 PEXOB5 CMH7 PIN X THREAD EACH END 5 CFA33 NUT M8 Page SPD33

22 Unloading roller (3) 3 Page SPD3

23 No. Part No Description Qty No. Part No Description Qty ABD3 REAR ROLLER998 ABD REAR ROLLER998 3 CBR6 BEARING FLANGE UNIT SF 3/" ART3 UNLOADING ROLLER 5 CFA3 WASHER FLAT MM Z/P 6 CFA9 NUT M NYLOC 7 CFA78 BOLT MX5 Z/P 8 CFA8 BOLT M6X5 8 9 CFA8 NUT M6 NYLOC 8 ART3 UNLOADING ROLLER CFA36 SETSCREW MX5 ZP CFA WASHER FLAT MM ZP 3 CFA6 NUT M NYLOC CBR5 BEARING PILLOW BLOCK NP3/" Page 3 SPD3

24 Unloading roller table (585) Page SPD585

25 No. Part No Description Qty No. Part No Description Qty ART37 BALE UNLOADING ROLLER ASSEMBLY ART3 BACK UNLOADING ROLLER 7 ART35 BACK UNLOADING ROLLER STOP ASSEMBLY 3 ART36 BACK UNLOADING ROLLER FRAME CCH7 CHAIN /" MM WIRE ZP 5 CFA5 LINCH PIN MM 6 CFA SETSCREW MX5 Z/P 7 CFA SETSCREW M8X6 Z/P 8 CFA3 NUT M NYLOC 9 CFA3 NUT M8 NYLOC Z/P CFA WASHER FLAT 6MM Z/P 6 CFA LINCH PIN 6MM CFA399 SETSCREW M6X3 Z/P 6 3 CFA57 D SHACKLE.375" GAL CMH38 BUSH X5X3 STEPPED 5 CMH399 SPACER RING 995LM GEARBOX 6 CMH PIN TOP LINK 6X76&7MM C.HOLE. 7 CSG9 SPRING EXT X5.8X69.6X55 8 CTP37 STABILISER ASSEMBLY 5 C/C 9 CZF569 6MM L UNLOADING ROLLER BRACKET 998 Page 5 SPD585

26 Cradle arm (35) Page 6 SPD35

27 No. Part No Description Qty No. Part No Description Qty CFA GREASE NIPPLE, M STRAIGHT 8 9 CCH JOINER LINK CRA87 8mm BORE LIFT CYLINDER COMPLETE (8mm BORE)SLAVE JOINER LINK 9 CCH3 OFFSET LINK CSE87 8mm BORE SEAL KIT (8mm BORE) OFSET LINK 3 CGD5 CHAIN GUARD CRA9 CYLINDER ROD (8mm BORE) 3 CFA9 WASHER, 8mm SKM 8mm BORE 3 CFA SETSCREW, M8x6 Z/P CRA95 CYLINDER GLAND (8mm BORE) 8mm BORE CRA93 CYLINDER PISTON (8mm BORE) 8mm BORE CRA86 LIFT CYLINDER COMPLETE (9mm BORE)MASTER 9mm BORE CSE86 SEAL KIT (9mm BORE) 9mm BORE CRA97 CYLINDER ROD (9mm BORE) 9mm BORE CRA98 CYLINDER GLAND (9mm BORE) 9mm BORE CRA96 CYLINDER PISTON (9mm BORE) 9mm BORE 3 CBR39 BUSH, GLACIER 55 6 CBR7 BUSH, GLACIER ARC6 CRADLE ARM, RIGHT LH 5 ARC7 CRADLE ARM, LEFT RH 6 CFA NUT, M NYLOC 7 CFA38 WASHER, mm FLAT 8 CFA ROLL PIN, 8x5 Z/P CMH76 PIN, TOP RAM PIVOT 3 CFA5 NUT, M PLAIN Z/P CFA3 SETSCREW, Mx Z/P 5 CFA3 SETSCREW, Mx3 Z/P 8 6 CBR3 BEARING, 35mm INSERT 7 CMH5 BEARING RETAINER 8 CFA3 CIRCLIP 9 CMT7 ROLLER DRIVE MOTOR CMH85 SPROCKET, 3/" PITCH 9 TOOTH UP TO SERIAL NO CMH367 SPROCKET, 3/" PITCH TOOTH FROM SERIAL NO. 599 CFA359 KEY, 8x7x3 CFA9 WASHER, 8mm MUDWING 3 CFA85 WASHER, 8mm SPRING CFA SETSCREW, M8x5 Z/P 5 CZF3 MOTOR PLATE 6 CFA33 SETSCREW Mx35 Z/P 7 CFA3 SETSCREW, Mx Z/P 8 CFA37 WASHER, mm SPRING 9 CCH7 CHAIN, 3/" C/W JOINER LINK Page 7 SPD35

28 Rollers (37) Page 8 SPD37

29 No. Part No Description Qty No. Part No Description Qty CFA3 SETSCREW MX3 Z/P 6 CCH8 CHAIN 3/ PITCH C/W JOINER LINK CFA37 WASHER MM SPRING 8 UP TO SERIAL NO CZD WASHER XX 8 7 CCH JOINER LINK 3/ UP TO SERIAL NO. 59 CFA39 KEY X8X 8 7 CCH3 OFFSET LINK 3/ 5 CMH5 SPROCKET 3/ PITCH 6 TOOTH 6 UP TO SERIAL NO CMH37 SPROCKET 3/ PITCH TOOTH 6 FROM SERIAL NO ARC ROLLER CRADLE RIGHT RH 6 ARC ROLLER CRADLE LEFT LH 7 CMH3 CRADLE PIVOT SHAFT 8 CBR3 35MM BEARING INSERT 8 9 CMH5 RETAINER RING 8 CFA3 CIRCLIP 8 CZF ADJUSTMENT CAM UP TO SERIAL NO. 59 ARC7 ADJUSTMENT CAM FROM SERIAL NO. 595 CFA3 SETSCREW MX Z/P 3 CMH7 SPROCKET 3/ PITCH 5/5 T UP TO SERIAL NO CMH6 SPROCKET 3/ PITCH 3/3 T FROM SERIAL NO. 595 CGD CHAIN GUARD UP TO SERIAL NO. 59 CGD3 CHAIN GUARD FROM SERIAL NO CFA9 WASHER SKM8 6 CFA5 SETSCREW M8X Z/P 7 ARC3 ROLLER (STEEL) UP TO SERIAL NO (STEEL ROLLER) 7 CPL3 ROLLER (PLASTIC) UP TO SERIAL NO (PLASTIC ROLLER) 7 ARC93 ROLLER STEEL 998 FROM SERIAL NO (STEEL ROLLER) 8 ARC SLOTTED LINK RIGHT RH 9 ARC5 SLOTTED LINK LEFT LH 9 CMH3 SLOTTED LINK BOTTOM PIN CFA ROLL PIN 8X5 Z/P CZD95 PLATE GUARD SENSOR RHS 998 RH CZD669 PLATE GUARD SENSOR LHS 998 LH CFA3 NUT M NYLOC 3 CZD SUPPORT PLATE CBR9 BEARING 35MM 3 BOLT STEEL 5 CFA7 SETSCREW MX3 CUPHEAD Z/P UP TO SERIAL NO CCH3 FROM SERIAL NO CCH FROM SERIAL NO CCH FROM SERIAL NO CZF7 FROM SERIAL NO a CFA83 FROM SERIAL NO CZC6 FROM SERIAL NO a CFA7 FROM SERIAL NO b CFA83 FROM SERIAL NO c CFA8 FROM SERIAL NO d CEL785 FROM SERIAL NO KST59 UP TO SERIAL NO.587 CHAIN 3/ PITCH LINK 6H CHAIN LINK CONN 3/ ANSI 6H CHAIN LINK OFFSET 3/ ANSI 6H 6MM L CAM ADJUSTMENT BOLT MX6 Z/P 8.8 3MM ANGLE SENSOR BRACKET Z/P SETSCREW MX SOC CAP SS 6 WASHER FLAT MM ZP WASHER MM SHAKEPROOF ANGLE SENSOR DEG.5-.5VOLT 998 CRADLE SENSOR UPGRADE KIT Page 9 SPD37

30 Drawbar (38) Page 3 SPD38

31 No. Part No Description Qty No. Part No Description Qty CFA LINCH PIN, SMALL ADB DRAWBAR SAFETY BAR 3 CFA35 WASHER, " FLAT CFA ROLL PIN, 8x5 Z/P 5 CMH7 PIN, RAM PIVOT ONE ON EACH END OF ITEM (CRA79) 6 ADB9 STAND PIVOT PIN 7 ADB STAND LOCKING PIN 8 CBR39 BUSH,GLACIER 55 9 CFA GREASE NIPPLE M STRAIGHT CVA DRAWBAR CYLINDER VALVE CRA79 DRAWBAR CYLINDER COMPLETE CSE73 SEAL KIT CRA99 CYLINDER ROD CRA9 CYLINDER GLAND CRA9 CYLINDER PISTON ADB7 DRAWBAR BEAM 3 CBR9 BUSH, GLACIER 66 CFA6 GREASE NIPPLE, M8 9 5 ADB8 STAND 6 CFA7 BOLT, MX6 Z/P 7 CFA3 NUT, M NYLOC Page 3 SPD38

32 Headstock (39) Page 3 SPD39

33 No. Part No Description Qty No. Part No Description Qty CFA3 SETSCREW, Mx5 Z/P CFA7 WASHER, MM SPRING 3 CZF PIVOT PIN TOP CAP CMH67 PIVOT PIN (SHORT) 5 ADB HEADSTOCK BARE 6 CFA38 WASHER, MM FLAT 7 CFA3 SETSCREW, Mx3 Z/P 8 CFA3 NUT, M8 NYLOC 9 CFA5 SETSCREW, M8x Z/P ADB HOSE TRAY CFA6 BOLT, M8x Z/P CFA75 SETSCREW, Mx35 FLANGED Z/P 3 CMT PUMP LOAD SENSING UP TO SERIAL NO 59 3 CMT35 PUMP 998 PISTON EATON FROM SERIAL NO 5 CMT GEARBOX 5 CZF5 WASHER x85x6 6 CFA33 SETSCREW, Mx35 Z/P 7 CMT9 PTO COVER 8 CZF6 PTO COVER RING 9 CFA65 SETSCREW, Mx5 Z/P CZF6 WASHER x55x6 CBR8 BUSH, GLACIER CMH5 CAT. LOWER LINK PIN 3 ADB5 HITCH BAR CFA5 LINCH PIN, LARGE 5 ADB6 HORIZONTAL PIVOT PIN 6 CFA8 GREASE NIPPLE, M8 STRAIGHT Page 33 SPD39

34 PTO shaft (33) Page 3 SPD33

35 No. Part No Description Qty No. Part No Description Qty CMT8 PTO SHAFT COMPLETE CMT PLASTIC BEARING RING, LARGE INSIDE CMT9 COVER COMPLETE 3 CMT PLASTIC BEARING RING, SMALL INSIDE CMT QUICK RELEASE BUTTON KIT 5 CMT5 OUTER YOKE (6 SPLINE) 6 SPLINE 5 CMT6 OUTER YOKE ( SPLINE) OPTION SPLINE 6 CMT7 UNIVERSAL JOINT 7 CMT8 INNER YOKE, LARGE PROFILE TUBE 8 CMT9 LARGE PROFILE TUBE 9 CMT3 SMALL PROFILE TUBE CMT3 INNER YOKE, SMALL PROFILE TUBE Page 35 SPD33

36 Hydraulic tank (33) Page 36 SPD33

37 No. Part No Description Qty No. Part No Description Qty CFA SETSCREW Mx5 Z/P 3 CFA37 WASHER MM SPRING 3 3 CHY9 RETURN FILTER COMPLETE 3 CHY3 RETURN FILTER ELEMENT 3 CHY5 RETURN FILTER CARTRIDGE (98) 3a CSE8 SEAL KIT 998 TANK FILTER CHY9 O-RINGS FOR FILTER CPL9 INTERNAL RETURN PIPE 5 CHY8 FILLER CAP 6 ADB HYDRAULIC TANK BARE 7 CHY7 OIL LEVEL GAUGE 8 CHY WASHER 3/ DOWTY 9 CHY DRAIN BUNG CFA8 NUT M6 NYLOC 3 CFA WASHER 6MM FLAT 3 CFA9 SETSCREW M6x35 Z/P 3 3 CSE6 OUTLET PLATE GASKET CHY3 SUCTION STRAINER 5 ADB3 OUTLET PLATE, FLAT FLAT 5 ADB5 OUTLET PLATE STEPPED STEPPED 6 CFA67 SETSCREW M6x5 Z/P 6 7 CHY58 SUCTION PIPE 5mm SUCTION PIPE ASSEMBLY FOR PUMP 8 CHY59 PIPE CLIP SUCTION PIPE ASSEMBLY FOR PUMP 9 CMH38 PUMP SUCTION FLANGE SUCTION PIPE ASSEMBLY FOR PUMP CHY6 O RING SUCTION PIPE ASSEMBLY FOR PUMP CHY6 FLANGE CLAMP SUCTION PIPE ASSEMBLY FOR PUMP CFA7 WASHER mm SPRING SUCTION PIPE ASSEMBLY FOR PUMP 3 CFA33 SETSCREW Mx35 Z/P SUCTION PIPE ASSEMBLY FOR PUMP Page 37 SPD33

38 Main conveyor main drive (33) Page 38 SPD33

39 No. Part No Description Qty No. Part No Description Qty CFA3 SETSCREW, Mx3 Z/P 38 ACN FRAME CFA37 WASHER, mm SPRING FROM SERIAL NO CZD WASHER, x5x 39 CCH5 CHAIN, " C/W JOINER LINK LINK UP TO SERIAL NO. 955 CMH3 ROLLER BUSH (PLASTIC) CGD6 CHAIN GUARD 5 ACN ROLLER FROM SERIAL NO CFA3 SETSCREW, Mx Z/P 6 CMH89 SPROCKET, " PITCH 8 TOOTH 7 CBR33 BEARING, MM BOLT STEP FLANGE FROM SERIAL NO CFA3 NUT, M NYLOC 6 9 CFA358 KEY, x8x7 CFA7 SETSCREW, M6x SOCKET CAP CFA WASHER, 6mm SPRING CMH3 SPROCKET, 75mm PITCH 7 TOOTH 3 CMH3 MAIN CONVEYOR REAR SHAFT CMH6 SPROCKET, " PITCH TOOTH UP TO SERIAL NO CFA63 KEY, x8x55 6 CFA9 SETSCREW M6x35 Z/P 6 7 CZF5 SIDEPLATE, RIGHT UP TO SERIAL NO CFA8 NUT, M6 NYLOC 6 9 CMH37 CHAIN ADJUSTER (PLASTIC) CFA5 WASHER, 6mm SKM CFA35 SETSCREW, M6x5 Z/P ACN FRAME UP TO SERIAL NO CFA8 GREASE NIPPLE, M8 STRAIGHT CMT6 CONVEYOR DRIVE MOTOR a CSE93 SEAL KIT FOR WHITE HYD MOTOR FOR WHITE HYD MOTOR ONLY b CSE SEAL KIT TG+TF PARKER HYD MTR FOR PARKER HYD MOTOR ONLY 5 CFA NUT, M NYLOC 6 ACN3 SIDEPLATE, LEFT UP TO SERIAL NO CFA356 BOLT, Mx5 Z/P 8 CMH77 SPROCKET, " PITCH TOOTH 9 CFA36 SPLITPIN 3 CFA36 MOTOR NUT 3 CFA5 WASHER, mm SKM 3 CFA3 BOLT, Mx5 Z/P 33 CCH9 CHAIN, " C/W JOINER LINK 39 LINK FROM SERIAL NO CCH JOINER LINK 33 CCH OFFSET LINK 3 CGD3 CHAIN GUARD UP TO SERIAL NO CFA3 NUT, M8 NYLOC 36 CZF9 SIDEPLATE, RIGHT FROM SERIAL NO ACN3 SIDEPLATE,LEFT FROM SERIAL NO Page 39 SPD33

40 Bale position sensor arms (33) Page SPD33

41 No. Part No Description Qty No. Part No Description Qty CFA ROLL PIN, 8x5 Z/P 7 CSG TENSION SPRING CFA37 WASHER, MM SPRING ACH5 SENSOR ARM, RIGHT FROM SERIAL NO RH ACH55 SENSOR ARM, LEFT FROM SERIAL NO LH 5 CMH5 ROLLER FROM SERIAL NO CFA3 SETSCREW, Mx3 Z/P FROM SERIAL NO CZD WASHER, xx FROM SERIAL NO CFA359 KEY, 8x7x3 FROM SERIAL NO. 5 9 CMH6 PLASTIC BUSH FROM SERIAL NO. 5 CMH73 BALE SENSOR ARM SHAFT FROM SERIAL NO. 5 Page SPD33

42 Front conveyor (335) Page SPD335

43 No. Part No Description Qty No. Part No Description Qty CFA8 NUT, M6 NYLOC 8 37 CCH7 JOINER LINK (COTTER) ACN BALE GUIDE, RH 37 CCH JOINER LINK (CLEAT) ACN5 BALE GUIDE, LH 37 CCH3 INNER LINK 3 CFA39 U BOLT, 8x8 38 ACN FRONT CONVEYOR REAR SHAFT CFA U BOLT, 8x5 39 CMH69 FRONT LIFT CYLINDER PIN 5 CFA5 SETSCREW, M6x Z/P CFA ROLL PIN, 8x5 Z/P 6 CFA WASHER, 6mm SPRING CFA39 WASHER, mm FLAT HEAVY DUTY 7 CMH3 SPROCKET, 75mm PITCH 7 TOOTH CFA78 SETSCREW, Mx3 CUPHEAD Z/P 8 8 ACN6 CONVEYOR, BARE 3 CFA8 SETSCREW, Mx Z/P 8 ACN7 CONVEYOR, COMPLETE ACN SIDEPLATE, RIGHT 9 CFA3 SETSCREW, Mx3 Z/P 9 UP TO SERIAL NO CFA7 WASHER, mm SPRING 9 5 CMH38 SPROCKET, " DUPLEX TOOTH NLS (6) ACN8 LATCH CLOSER 6 CFA9 NUT, M NYLOC 5 CFA3 NUT, M NYLOC 6 7 CMH36 WASHER, CUP 3 CBR33 BEARING, mm BOLT STEP FLANGE 5 8 CMH3 SPROCKET, mm PITCH 6 TOOTH 5 CFA3 SETSCREW, Mx Z/P 8 9 CBR3 BUSH, GLACIER CFA5 NUT, M PLAIN Z/P 5 CMH35 BUSH, STEEL HARDENED 5 6 CFA7 BOLT, Mx6 Z/P 5 CMH8 PIN, FRONT SPROCKET PIVOT 5 7 CCH3 CHAIN, " DUPLEX & JOINER LINK UP TO SERIAL NO CFA6 GREASE NIPPLE, M8 9 DEGREE 5 7 CCH6 UP TO SERIAL NO. 955 " DUPLEX JOINER LINK 53 ACN 5 CFA SKID WASHER, mm FLAT 7 CCH7 " DUPLEX OFFSET LINK 55 CFA6 NUT, M NYLOC UP TO SERIAL NO CFA WASHER, mm FLAT 8 CMH39 SPROCKET, " DUPLEX TOOTH 57 CFA SETSCREW, Mx Z/P NLS (6) 58 ACN5 SIDEPLATE,LEFT 9 CFA63 KEY, x8x55 FROM SERIAL NO CZD WASHER, x5x 59 ACN6 SIDEPLATE, RIGHT CFA37 WASHER, mm SPRING FROM SERIAL NO CFA3 SETSCREW, Mx3 Z/P 6 CMH SPROCKET, " TOOTH 3 CMH3 CHAIN ADJUSTER DUPLEX (PLASTIC) FROM SERIAL NO CFA5 WASHER, 6mm SKM 6 CMH SPROCKET, " TOOTH FROM SERIAL NO CFA35 SETSCREW M6x5 Z/P 6 CCH CHAIN, " LINK,OFFSET & JOIN 6 CFA5 WASHER, mm SKM FROM SERIAL NO CFA8 BOLT, Mx9 Z/P 6 CCH " JOINER LINK 8 CZD9 CHAIN GUARD 6 CCH " OFFSET LINK 9 CFA38 WASHER, mm FLAT 3 3 CFA NUT, M NYLOC 7 3 CFA358 KEY, x8x7 3 CMH33 MAIN CONVEYOR FRONT SHAFT 33 CFA6 SETSCREW, Mx FINE UP TO SERIAL NO CFA39 WASHER, mm SPRING UP TO SERIAL NO CZF69 WASHER, x5x6 UP TO SERIAL NO ACN9 SIDEPLATE, LEFT UP TO SERIAL NO CCH PICK UP CHAIN C/W JOINER LINK 5 37 CCH5 JOINER LINK (RIVETED) Page 3 SPD335

44 Spare film holder (337) Page SPD337

45 No. Part No Description Qty No. Part No Description Qty ADB SPARE ROLL HOLDER ASM 998 INCLUDES ITEMS THROUGH 6 ADB5 SPARE ROLL HOLDER WELD ASM 998 CBC7 CAP BLACK PLASTIC.3/8" OSF 8 3 CBC CAP SQ PLASTIC INSERT 8 X 5 CFA NUT M NYLOC 6 5 CFA33 BOLT MX3 Z/P 6 6 CZF 6MM L ROLL HOLDER MOUNT BRCKT Page 5 SPD337

46 Round bale kit (36) Page 6 SPD36

47 No. Part No Description Qty No. Part No Description Qty ACH ROUND BALE PIPE ASSEMBLY ACH ROUND BALE PIVOT PIN ASM. 3 ACH WHEEL BRACKET ASSEMBLY ACH6 ROUND BALE KIT ATTACHMENT 5 CFA5 LINCH PIN MM 6 CFA3 SPLIT PIN 5X5 Z/P 6 7 CFA SETSCREW MX5 Z/P 8 CFA ROLL PIN X6 9 CFA3 NUT M NYLOC CFA8 NUT M6 NYLOC 6 CFA WASHER FLAT MM Z/P CFA LINCH PIN 6MM 3 CFA399 SETSCREW M6X3 Z/P CFA8 BOLT M6X3Z/P 5 CMH5 PIN 3/" X35 TOP LINK 6 CMH5 BUSH X58X&MM C 7 CMH39 PIN 5X355&X6MM CH 8 CMH393 PIN 5X75&X6MM CH 9 CTP CAT TOP LINK EXTENDED 998 ROUND BALE KIT REPLACES CTP36 CWH WHEEL ASY./ CXT5 C33.7X3X5 CXT53 C33.7X3X5 3 CZF58 6MM L BALE ATTACHMENT BRCKT. CZF58 6MM L BALE ATTACHMENT BRCKT. 5 CZF58 6MM L FRONT ATTACHMENT BRCKT Page 7 SPD36

48 Small bale kit (38) Page 8 SPD38

49 No. Part No Description Qty No. Part No Description Qty ARC6 ROLLER CRADLE BALAST BRACKET ASSY CFA75 SETSCREW M X 35 FLANGED Z/P 3 CFA WASHER FLAT MM Z/P CFA6 NUT M NYLOC 5 CVA3 FLOW CONTROL VALVE Page 9 SPD38

50 Hydraulic control valve (338) Page 5 SPD338

51 No. Part No Description Qty No. Part No Description Qty CVA6 VALVE CTL DPC3/ CVA69 CLOSED CTR KIT DPC3 OVERALL ASSEMBLY 8 CVA6 CTE SHUTTLE VALVE DPC CFA568 M6x.5-Fc= SCREW 8 CSE38 SEAL KIT DPC3 SHUTTLE VALVE CHY ADAPTOR /" BANJO ASY COMP SEAL KIT FOR SHUTTLE VALVE CVA6 3 CVA3 LEVER PIVOT BOX DPC3 9 CSE SEAL O-RING LEVER BOX DPC3 CVA SPOOL ROTATION WASTE 998 REPLACES EITHER CVA7 OR CVA587 TO IMPROVE SLOW-SPEED PERFORMANCE 5 CVA8 SPOOL, CUT & HOLD 6 CVA9 SPOOL, CONVEYOR 7 CVA SPOOL, BALE LIFT 8 CVA SOLENOID DPC3 9 CVA75 END BLOCK VALVE CHEST CVA76 PLUG BSP /" 5 CVA77 FLOW LIMITER DPC3 CVA78 VALVE SECTION DPC3 D 3 CVA79 VALVE SECTION DPC3 C CVA8 VALVE SECTION DPC3 C 5 CVA86 SECTION COMPENSATOR DPC3 6 CVA87 SEAL KIT DPC3 "O" RINGS 6 7 CVA89 VALVE DPC3 (-8 BAR) 8 CVA9 VALVE DPC3 (8-35BAR) 9 CVA9 FILTER LOAD SENSING DPC3 CVA93 VALVE PRESSURE REDUCING DPC3 CVA9 O-RING SEAL 5 X.MM PARKER CVA95 O-RING SEAL.95MM X.78MM 6 3 CVA96 CONTROL MODULE DPC3 CVA97 SOC CAP M5 X 55MM 8 5 CVA98 WASHER ELASTIC M5 6 CVA99 O-RING SEAL.MM X.78MM 8 7 CVA PRESSURE REDUCER DPC3 8 8 CVA SOC CAP M6 X 55MM 9 CVA3 JOINT DPC3 3 CVA OPEN BUSHING DPC3 8 3 CVA5 SPRING DPC3 3 CVA6 RING. X 3 X 3MM 33 CVA7 PLUG DPC3 3 CVA55 TIE ROD KIT VALVE CHEST 35 CVA3 DPC3/ELP BODY 36 CVA3 DPC3-DPC6 VALVE 37 CVA3 UT/DPC3-SDS PLUG 38 CVA33 LT/DPC6-DPC3-SDM8 PLUG 39 CVA3 BSP / PLUG CVA35 ELP/DPC3-BSP WORKING SECTION CVA36 FE/DPC3/BR-BSP INLET COVER CVA37 DPC3/ELP-SPOOL 3 CVA38 M8x.5 PLUG CVA39 Mx.5 DIN 96 PLUG 5 CVA3 DPC3/ELP-FLANGE 6 CVA3 UNI-593/M6x8-8.8 GALVANIZED Page 5 SPD338

52 Hydraulic valve roller rotation (339) Page 5 SPD339

53 No. Part No Description Qty No. Part No Description Qty CVA ROLLER ROTATION BLOCK COMPLETE CVA38 VALVE "CC" CVA39 VALVE "NFC" CATRIDGE & COIL COMPLETE CVA63 EATON COIL CVA39 COIL ONLY 3 CFA37 WASHER, mm SPRING CFA3 SETSCREW, Mx Z/P Page 53 SPD339

54 Hydraulic valve dispenser drive (3) Page 5 SPD3

55 No. Part No Description Qty No. Part No Description Qty CVA53 VALVE ROTATION 998 CVA87 CTE PRESSURE REDUCING HS & 998 CVA3 OVER CENTRE VALVE ASSY 3 CVA7 CTE 99BJS DETENT VALVE Page 55 SPD3

56 Hydraulic pipes steel (3) Page 56 SPD3

57 No. Part No Description Qty No. Part No Description Qty CFA5 WASHER mm SKM CFA9 WASHER 8mm SKM 5 3 CFA9 SETSCREW M8x SOCKET CAP Z/P CHY39 STEEL PIPE ASSEMBLY REAR RIGHT 5 CHY36 STEEL PIPE ASSEMBLY FRONT RIGHT 6 CHY3 STEEL PIPE ASSEMBLY DRAWBAR TOP 7 CFA36 BOLT M8x3 Z/P 8 CHY33 STEEL PIPE PUMP INTERNAL RETURN 9 CHY3 STEEL PIPE TANK RETURN CHY5 WASHER /" "DOWTY" CHY37 STEEL PIPE ASSEMBLY REAR LEFT CHY38 STEEL PIPE ASSEMBLY FRONT LEFT 3 CHY5 WASHER /" "DOWTY" 3 CHY56 PRESSURE TEST ADAPTOR CVA3 NON RETURN VALVE /" 5 CHY35 STEEL PIPE ASSY DRAWBAR BOTTOM 6 CFA SETSCREW M8x6 Z/P 7 CHY WASHER 3/" "DOWTY" 8 CHY57 ADAPTER 5/8"M - 3/" M Page 57 SPD3

58 Air brake kit 998 up to & incl 8 (37) Page 58 SPD37

59 No. Part No Description Qty No. Part No Description Qty CVA AIR BRAKE ACTUATOR CHY5 HOSE A/B.85M LONG 5MM X 5.5MM 3 CVA8 TEE PIECE AIR BRAKE VALVE CHY8 HOSE A/B M LONG 5MM X.5MM 5 CHY6 HOSE A/B.9M LONG 5MM X 5.5MM 6 CVA3 AIR BRAKE AIR VALVE 7 CHY7 HOSE A/B.9M LONG 5MM X.5MM 8 CHY HOSE A/B 5.3M LONG 5MM X 5.5MM 9 CVA6 AIR BRAKE QUICK FIT COUPLING CVA7 AIR BRAKE QUICK FIT BRACKET (RED) CVA3 AIR BRAKE QUICK FIT BRACKET (YELLOW) CVA5 AIR BRAKE AIR TANK 3 CVA3 RELIEF VALVE, AIR BRAKE TANK CVA3 DRAIN TAP, AIR BRAKE TANK Page 59 SPD37

60 Air brake kit 998 from 9 onwards (9) Page 6 SPD9

61 No. Part No Description Qty No. Part No Description Qty CVA38 COUPLER BRACKET CVA6 PALM QUICK FIT COUPLING (YELLOW) M 3 CVA7 PALM QUICK FIT COUPLING (RED) M CHY557 SERVICE SUZZIE (YELLOW) 5 CHY558 EMERGENCY SUZZIE (RED) 6 CHY559 MM O/D NYLON AIR BRAKE HOSE AR 7 CHY65 CONTROL VALVE AIR BRAKE KIT [TRACTAIR] 8 CVA AIR BRAKE ACTUATOR FUSION 998 F5 9 CVA3 LTR AIR RESERVOIR TANK CVA35 RESERVOIR SADDLE SADDLE BRACKET CVA37 AIR BRAKE M6 TEST POINT CZC36 3MM L AIR BRAKE BRACKET 998 MOUNTING PLATE 3 CZH8 MM L BALEHANDLER WASHER 5 CST88 DECAL KIT FOR CHY567 AIR BRAKE 5 CFA SETSCREW MX5 Z/P 6 CFA7 SETSCREW M6X5 Z/P 7 CFA3 NUT M NYLOC 8 CFA WASHER FLAT MM Z/P 8 9 CFA5 WASHER SKM6 Page 6 SPD9

62 Electrical components [Up to Serial No 567] (3) Page 6 SPD3 3

63 No. Part No Description Qty No. Part No Description Qty CEL CONTROL BOX AUTO 998 KST6 998 CONTROL UNIT ADAPTOR KIT REPLACEMENT ADAPTOR KIT TO EXPERT CONTROL BOX UP TO SERIAL NO 567 CEL3 POWER LEAD 3 CEL6 EURO POWER LEAD CEL PIN EXTENSION 5 CEL MAIN LOOM UP TO SERIAL NO 56 5 CEL5 MAIN LOOM FROM SERIAL NO 56 TO 567 6a CEL9 MODULE SLOW SPEED 998 UP TO SERIAL NO 56 6b CEL5 MODULE SLOW SPEED 998 FROM SERIAL NO 56 TO CEL SENSOR CABLE 3.6M 3 8 CEL9 EXTENSION CRADLE POT CEL8 POTENTIOMETER 998 CRADLE CEL38 SAFETY ARM SWITCH CEL6 SLIPRING LOWER LOOM CEL7 SLIPRING 3 CEL5 CON ASY SLIPRING WAY TOP CEL LOOM SWITCH SAFETY CEL7 MAGNET LARGE BLUE 3 6 CEL59 MAGNET X CEL5 MODULE COMPARATOR 998 Page 63 SPD3 3

64 Electrical components [Serial No 568 to 587] (33) Page 6 SPD33 5

65 No. Part No Description Qty No. Part No Description Qty CEL68 EXPERT CONTROL UNIT CEL88 EXPERT CONTROL BOX SCREEN REPLACEMENT SCREEN FOR EXPERT CONTROL BOX CEL3 SCREEN PROTECTOR EXPERT CEL67 CONTROL UNIT STOP SWITCH CEL67 STOP SWITCH CONTACT BLOCK - FOR CEL67 CEL365 CTRL UNIT CONNECTOR LOCK RING REPLACEMENT LOCK RING TO CONNECT TO MAIN LOOM CPL7 VACUUM PAD FLAT BACK CEL3 POWER LEAD 3 CEL6 EURO POWER LEAD CEL86 37 PIN EXTENSION 5 CEL68 MAIN LOOM 6 CEL93 PWM MODULE 7 CEL6 HEIGHT POTENTIOMETER 8 CEL9 EXTENSION CRADLE POT CEL8 POTENTIOMETER 998 CRADLE KST59 AVAILABLE AS AN UPGRADE KIT CEL38 SAFETY ARM SWITCH CEL6 SLIPRING LOWER LOOM CEL7 SLIPRING 3 CEL5 SLIPRING UPPER LOOM CEL TRANSMITTER EVEN 5 CEL TRANSMITTER ODD 6 CEL69 TOP ARCH LOOM 7 CEL3 FILM BREAK RECEIVER 8 CEL5 MODULE COMPARATOR CEL35 MAGNETIC SENSOR CEL7 MAGNET LARGE BLUE 3 Page 65 SPD33 5

66 Electrical components [From Serial No 588] (797) Page 66 SPD797

67 No. Part No Description Qty No. Part No Description Qty CEL68 EXPERT CONTROL UNIT CEL88 EXPERT CONTROL BOX SCREEN REPLACEMENT SCREEN FOR EXPERT CONTROL BOX CEL3 SCREEN PROTECTOR EXPERT CEL67 CONTROL UNIT STOP SWITCH CEL67 STOP SWITCH CONTACT BLOCK - FOR CEL67 CEL365 CTRL UNIT CONNECTOR LOCK RING REPLACEMENT LOCK RING TO CONNECT TO MAIN LOOM CPL7 VACUUM PAD FLAT BACK CEL3 POWER LEAD 3 CEL6 EURO POWER LEAD CEL86 37 PIN EXTENSION 5 CEL68 MAIN LOOM 6 CEL93 PWM MODULE 7 CEL6 HEIGHT POTENTIOMETER 8 CEL798 ANGLE SENSOR EXTENSION LEFT 9 CEL799 ANGLE SENSOR EXTENSION RIGHT CEL785 ANGLE SENSOR CEL38 SAFETY ARM SWITCH CEL6 SLIPRING LOWER LOOM 3 CEL7 SLIPRING CEL5 SLIPRING UPPER LOOM 5 CEL TRANSMITTER EVEN 6 CEL TRANSMITTER ODD 7 CEL69 TOP ARCH LOOM 8 CEL3 FILM BREAK RECEIVER 9 CEL797 COMPARATOR VERSION- CEL35 MAGNETIC SENSOR CEL7 MAGNET LARGE BLUE 3 Page 67 SPD797

68 Electrical lighting (3) Page 68 SPD3

69 No. Part No Description Qty No. Part No Description Qty CEL7 7 PIN PLUG & LOOM CEL79 FRONT RECTANGULAR REFLECTOR (WHITE) 3 CEL7 FRONT MARKER LIGHT & LOOM CEL73 JOINER LOOM 5 CEL78 SIDE RECTANGULAR REFLECTOR (ORANGE) 6 CEL75 LEFT HAND REAR LIGHT 7 CEL76 RIGHT HAND REAR LIGHT 8 CEL77 REAR TRIANGULAR REFLECTOR (RED) 8 CFA88 SETSCREW, M5x6 PAN HEAD 8 CFA3 NUT, M5 NYLOC 8 CEL WORK LIGHT & LOOM Page 69 SPD3

70 Remote control options (63) Page 7 SPD63 3

71 No. Part No Description Qty No. Part No Description Qty CEL3 REMOTE HAND PIECE CEL REMOTE RECEIVER 3 CZD8 MM L REMOTE POD BRACKET CPL7 VACUUM PAD FLAT BACK 5 KST7 KIT REMOTE + BEACON 99/995 REPLACED BY RADIO REMOTE CONTROL KIT KST (HS)& KST53 (99/995) 5 KST KIT INFARED REMOTE+BEACON 998 USED ON 998 ONLY 6 CZC36 BRACKET REMOTE TRANSMITTER. 7 CEL665 RECEIVER 8 CEL66 HAND PIECE 9 CEL9 BEACON XENON AMBER REPLACES CEL3 CEL93 CABLE EXT.8M BEACON 99/995 USED ON 99/995 ONLY CEL9 CABLE EXT BEACON HS USED ON HS ONLY UP TO SERIAL No 5569 CEL WARNING BUZZER ADP6 BRACKET BEACON XENON KST KIT REMOTE + BEACON HS USED ON HS SERIES ONLY KST53 KIT RADIO REMOTE+BEACON 99/995 USED ON 99/995 SERIES ONLY Page 7 SPD63 3

72 Decals (35) Page 7 SPD35

73 No. Part No Description Qty No. Part No Description Qty CST DECAL SET COMPLETE CST7 HANDS CLEAR OF ROTATING PARTS CST PLASTIC FILM PATH 3 CST WARNING! ROTATING ELEMENTS CST33 DECAL "MCHALE" CST36 DECAL "998" 6 CST6 HYDRAULIC SYSTEM AWARENESS 7 CST5 REMOVE IGNITION KEY 8 CST3 PTO SPEED 9 CST CHECK OIL LEVEL CST DRAWBAR CRUSH AREA CST685 DECAL MAX DISPENSER SPEED 5RPM CST DISPENSER ROTATION WARNING 3 CST3 LIFTING HOOK CST9 HAND CRUSH AREA 5 CST CHECK WHEEL NUTS 6 CST CHECK TYRE PRESSURE 7 CST56 HYDRAULIC ACCUMULATOR WARNING 3 8 CST6 HAND ENTRAPMENT Page 73 SPD35