2. Compartments 2 compartments with gallons front to rear with double bulkheads

Transcription

1 January 10, 2016 STE # & (Ref. QT 3098/STE# ) ST&E SPECIFICATIONS FOR 4,000 US GALLON DOT-407 DOUBLE CONICAL STAINLESS STEEL INSULATED TWO COMPARTMENT TANDEM TRANSPORT TANK PREPARED FOR STOCK TANK QUANTITY 2 UNITS 1. Capacity 4,000 US Gallon shell full 2. Compartments 2 compartments with gallons front to rear with double bulkheads 3. Shape Round double conical with 12 pitch to center 4. Products Various Acids 5. Maximum Product Weight 16 pounds per gallon 6. Weight Laws 80,000 GVW 42 OAL Tank States of Operation- Canadian Weight Laws 7. Product Temperature 250 degrees F maximum temperature 8. Code DOT Working Pressure 25 PSI with 40 PSI test 10. Tank Shell & Finish 8 gauge 304 2B stainless steel 11. Tank Head 8 gauge 304 2B stainless steel ASME flanged & dished head 12. Inside Weld Finish Ground & polished #4 finish Outside Weld Finish All outside welds snag free 13. Baffles (2) full dished only baffles with drain at bottom, vent at top, & 20 diameter reinforced walk-through opening at center, (1) located equally spaced between heads in each compartment 14. Rings Stainless steel fully welded to inner tank 15. Bolsters Stainless steel 16. Frame Stainless steel sub frame 17. Heat Section 24 wide full length dimple heat section full length of each compartment with individual control for each compartment for Webasto heater STE & Page 1

2 18. Insulation 6" thick fiberglass compressed to 5" 19. Wrapper Top Back-up 15 Aluminum hard top between end heads and spill dam rollover & 15 at bottom and at side walkway full length 20. Wrapper lap back-up Polyurethane foam with maximum of Outer Jacket 22 gauge stainless steel bright annealed buff with lapped seams 22. Outer Heads 18 gauge stainless steel bright annealed finish with lock seam joints 23. Manhole (2) 20 x 10 diameter Betts chemical style full opening manhole, hypalon gaskets and hold-downs, with 10 fill with 3 hold downs & hinge pin at front located near center of each compartment 24. Spill Dam One full length stainless steel fully welded floor spill dam from front 10 fill to rear 10 fill 25. Spill Dam Hose (2) 1 l/2 diameter Tigerflex drain hoses located one each side at rear of spill dam 26. Roll Over At rear of spill dam & at front of spill dam 27 Clean Outs (2) 3" threaded flange with blind flange, one located in each compartment in spill dam. (2) Betts 10 pressure fills with hypalon gasket located (1) between baffle & end head in each compartment 28. Vents (2) 3 Fort Vale ANSI flanged 407 pressure/vacuum vent rated at 30 PSI bolted on 3 threaded flange located one near center of each compartment in spill dam with ¾ ball valve air inlet with Chicago coupler, cap and cable & 0-60 PSI pressure gauge 29. Vapor Recovery None 30. Air Unloading Line None 31. Emergency Valve 4 stainless disc and stem air to open, spring to close butterfly valve with Buna-n seat on 4 ANSI 150# threaded flange located at bottom rear of compartment #1 and at bottom front of compartment#2 32. Emergency Valve Operator (4) Air toggle valves in pump cabinet for outlet and load valves and (1) remote toggle valve at street side front head 33. Outlet Valve 4 stainless disc and stem lever operated butterfly valve with Buna-n seat 34. Valve Gaskets Buna-n 35. Outlet Fitting 4 stainless pipe nipples with stainless solid caps at outlet valves and pump outlet STE & Page 2

3 36. Piping 4 stainless steel piping grouped together at street side center with tee to 4 valve to pump and valve to street side outlet. Stainless steel under ride guard and pump platform at outlet valves (see drawing) 37. Load Line (1) 4 stainless disc and stem air to open, spring to close butterfly valve with Buna-n seat on ANSI 150# threaded flange with 4 elbow at top ahead of baffle in front compartment with 4 stainless steel piping down curb side to outlet area with tee to 4 stainless disc and stem lever operated butterfly valve with Buna-n seat at 90 degrees with stainless nipples and stainless caps at curbside and street side and (1) 4 stainless disc and stem air to open, spring to close butterfly valve with Buna-n seat on ANSI 150# threaded flange 4 elbow behind the baffle at the rear compartment with 4 piping down curbside to outlet area with tee to 4 stainless disc and stem lever operated butterfly valve with Buna-n seat at 90 degrees with stainless nipple with stainless caps (see drawing) at curbside and street side 38. Government Seals On all openings (none on outlet stainless nipples and caps) 39. Walkway 12 wide aluminum grip strut on street side centerline of tank from front of front spill dam to rear of rear spill dam, stainless outside rail 42 high full length with 3 stainless steel toe rail at outside of walkway and additional center rail 40. Ladder (1) 16 wide stainless steel ladder with channel rungs located street side rear half of walkway above ladder 41. Rear Light Box Stainless steel bolt on 42. Lights & Wiring Truck-Lite LED lights in stainless boxes with wire harness system, two work lights, one at front rollover with switch at street side front head and one at rear rollover with switch at street side running gear & center side marker tied in turn signal 43. Nose Box 7 way receptacle on stainless bracket with glad hands located below centerline of front head 44. Fenders Aluminum contour 96 on front and 102 on rear with stainless supports 45. Mud Flaps STE black stainless steel supports at front of tandem & rear of tandem and full width mud flaps behind front fenders with stainless steel supports. Use anti sail brackets at mud flaps at front of tandem only 46. Bumper 4 x 8 x 21 DOT split stainless steel channel type with 4 x 4 x 95 stainless steel Canadian under ride guard. 47. Tire Carrier None STE & Page 3

4 48. Landing Gear 2 speed, heavy-duty Jost A400T leg with sand shoes with crank on curbside & stainless steel frame 49. Fifth Wheel Heavy-duty 5/16 thick STE bolted adjustable plate 50. Suspension Hendrickson Intraax #AAT-23K-17 Tandem air ride with manual dump valve in small stainless steel box located at curbside landing gear frame & 44 wide 7 gauge stainless steel frame (102 width, 49 spread) 51. Axles (2) Intraax round axle (23,000# rating) with HP spindles x 77.5" track 52. Brake System Brakes: Spring brakes & equipment to meet 121 standards, S-Cam, 16 l/2 x 7 Slack Adjusters: Automatic Dust Shields: YES ABS System: Meritor Wabco 4S/2M ABS Roll Stability: NONE Air Tanks: Steel air tanks 53. Hubs 10 stud cast hub piloted with outboard mounted cast drums 54. Wheel Seals Oil seals 55. Hub odometer Stemco in kilometer located at curb side front axle 56. Wheels (8) 8.25 x hole hub piloted aluminum disc, mill finish 57. Tires (8) 11R-24.5 (G) General ply radials Tire Pressure System None 58. Hose Carrier (2) 8 dia x 16 long aluminum hose tubes located one per side with cast aluminum doors both ends 59. Thermometer (2) F clip on bulb type thermometer located curb side eye level below manhole each compartment 60. Calibration Theoretical 1 increments in paper chart based on innage 61. Paint Prime and Paint all mild steel parts DuPont black 99X DO NOT PAINT STAINLESS STEEL 62. Conspicuity 2 wide Retro-Reflective Red/White stripes on both sides and rear 63. Customer Decals None 64. Placard Holders (8) stainless steel placard holders mounted curbside and street side doors 1 each door and (2) on front hydraulic hose pipe and (2) on running gear side rail 65. ID Holder Betts PS-1 mounted curbside on landing gear frame STE & Page 4

5 66. Pump Cabinet 71 L x 58 W x 28 D non insulated stainless steel cabinet with 2 doors on curbside and street side with dairy style latch and moonlight springs 67. Level Indicator ¼ x 1 T304SS plate etched in 1 increments at manhole collar x 12 long 68. Top Agitator flange (4) total, 6" ANSI 150# flange with blind flange located at 15 at top located (2) in each compartment 69. Level gauge 4 SCH 40 stainless pipes x 4 long with flat top & 1 pipe Coupling located in top of tank directly next to the outlet valve opening in the bottom of the tank away from the center heads with the Titan TD80 installed in the coupling with bottom support cone welded to tank bottom and wire from top down street side to the 2 monitors located one front and rear on street side wall in bottom pump cabinet. Gauge will provide liquid level read out only. Power for gauges and monitor is powered from blue circuit. 70. Tow Plate 1 thick mild steel full width at bottom of running gear frame x about 10 long with 1 ½ hole at rear 71. Pump Hydraulic powered pump and motor. Install ST&E supplied ball valve between pressure and return lines. 1 stainless steel hydraulic pressure pipe and 1 stainless steel hyraulic return line full length on curbside. 4 butterfly valve on pump outlet with 4 stainless steel pipe nipple with stainless cap on street side 72. Heater Install Webasto DBW 300 diesel 12 volt tractor pre-heater mounted in enclosure ahead of belly cabinet. Install 30 gallon diesel fuel tank on street side ahead of belly cabinet. Insulated aluminum reservoir tank for glycol on curbside ahead of belly cabinet for Webasto heater 73. Hose Hook Stainless steel swivel hook at street side front head at top of vertical support from skid plate to top of ring side for hydraulic hose 74. Hydraulic Hose Fitting (2) 1 stainless pipe couplings (on 3 ½ vertical centers) above skid plate on hose hook vertical support 75. Fitting Basket 1 ½ x 9 (10)-11 stainless steel expanded and flattened metal located between rings behind ladder approx. 17 high x 34 wide x 32 long with door on curbside and hinge on bottom and pad lock tabs at top CUSTOMER APPROVAL DATED NOTE: Any changes to the above specifications must be made in writing to Stainless Tank and Equipment Co. STE & Page 5

6 53.5 Fifth wheel, 244 wheel base, Front Rear AXLE WEIGHTS #50 was AANT CHANGES MADE: 11/19/14 #36 Changed mild steel piping to stainless steel 1/14/15 #31,#37,#68 was weld neck 1/20/15 Revised per last tank and review 1/23/15 Dished only baffles STE & Page 6