Specification Sheet Form Rev

Transcription

1 Sales Administration Use Only Quote Name Quote Revision Shop Order Number Serial Number(s) Date Customer : Customer Name Salesperson : Salesperson Name Model : HB S1, Hybrid Duty Petroleum Trailer Part / Drawing Number : Customer Furnished Tractor Data Required Weights to Include Driver, Fuel, Tools, Equipment, etc. Enable Track Changes on the Review Tab to identify deviation from the Base Model Specification A. VESSEL A1. Shell Material Aluminum alloy. All sizes/gauges are nominal. Top: Sides: Bottom: Notes: A2. Shell and Head Finish 0.182in front section, 0.194in center section, 0.182in rear section 0.182in 0.204in front section, 0.250in rear section Outriggers and pads to be Standard Duty configuration. Enhanced mill finish bulk trailer sheet. A3. Shape Elliptical, GPI A4. Specification DOT 406 A5. Vapor Testing Tested at 5 PSI rated at 3.3 PSI. Vapor tested and certified to EPA Method 27-CA Air Resources Board standards and manholes sealed. A6. Nominal Capacity 9,000 Gallons plus 3% outage. 60 gallons is the minimum outage for any size compartment. A7. Compartments 1 Compartments, front to rear 9000 gallons A8. Bulk Heads Aluminum alloy. All sizes/gauges are nominal. Front: 0.204in stiffened and shoed Rear: 0.204in stiffened and shoed A9. Surge Heads Aluminum alloy. All sizes/gauges are nominal. All surge heads are dished & flanged with (1) 20" man way center, (2) 12" drain holes 6 and 12 o'clock, and (2) 3" emergency drain 3 and 9 o'clock. Over Kingpin: Over Rungear: Middle of Tank: 0.204in stiffened and shoed 0.204in stiffened and shoed 0.204in unstiffened A10. Flashing Full length, double leg extrusions. Dams front and rear with transverse overturn protection rails as required by code. Page 1 of 6

2 A11. Documentation Computer generated calibration charts 1/2" increments. HM-183 documentation w/markings on front head. Vapor test decal with documentation. Unit hydrostatically tested. A12. Operating -20 F to 180 F Temperature A13. Lading Gasoline, Diesel Fuel, or similar A14. Miscellaneous None B. TANK FITTINGS AND PIPING B1. Manholes (1) 20" Civacon offset manhole per compartment. Includes NV3000 PV Valve,10 aluminum vent, and Buna N gaskets. Meets HM 183 and CFR venting requirements. Install emergency drain plug in manhole assembly. B2. Capacity Indicators Indicator Rods: Additional Discs: If ordered, each capacity indicator rod will come with one disc. Additional discs may be ordered. (1) Pemex aluminum indicator rod assembly with Bronze indicator disc (1) per compartment B3. Internal Ground (1) 1/8" stainless steel static ground wire per compartment. B4. Venting DOT406 venting in manhole. Additional venting is required to meet DOT406 regulations. Locate additional venting in the shell, on the top of the trailer. B5. Cleanouts/ Fill Covers B6. Vapor Recovery Vent Materials: B7. Vapor Recovery Connection B8. Vapor Recovery Piping None (1) 3" Civacon air operated inward opening sequential vent per compartment. Located in each manhole cover. Aluminum vent with stainless trim & Viton seats. Black Nylon vapor recovery nipple connected to flashing rail A hose connects the vapor recovery vent to the vapor recovery nipple 4" Aluminum External vapor line from rear curbside down curbside rear head. Line to continue to the following locations: (1) curbside outlet 18 forward of discharge, inside cabinet. (4" outlet). (1) curbside outlet to rear of rear head. (4" outlet). B9. Vapor Recovery Fittings (1) 4in adapter and dust cap, curbside, 18" forward of discharge (1) 4in adapter and dust cap, curbside, rear of rear head All vapor adapters are eight (8) bolt TTMA flange mounted and located per API RP Page 2 of 6

3 1004, where applicable. B10. Additional Venting None B11. Emergency Valve (1) Civacon 5 x 4 MaxAir II TM, internal cylinder, EV per compartment Materials: Aluminum body with Teflon seat. Splash shield-vortex breaker over each EV. B12. Operator System Civacontrol II air control kit. To simplify piping, a straight valve may be used in place of an elbow style. Mounted in curbside cabinet, centered between API and Vapor fitting One emergency trip located street side, front of tank. B13. Piping/Piping Gasket 4" Schedule #10 aluminum discharge piping with large radius formed sweeps to curbside of tank, located per API standards. Piping to terminate inside curbside cabinet. Flanged: Grooved: Grooved: Viton gaskets on flanged piping connections Dixon Aluminum couplers on groove-groove connections Baylast gaskets on groove-groove connections B14. Discharge Valve (1) 4" Civacon openable adapter per compartment B15. Discharge Accessories Materials: Aluminum handle and Viton seals Inside curbside cabinet. (1) 4" API to 4" cam style hose adapters and caps B16. Streetside None Discharge B17. Pump Off-Line None B18. Overfill System Civacon Five Wire system with #3100 controller and probe. Monitor Mounted on trailer frame. Probe: Socket: Socket Socket: Socket (1) top probe per compartment Installed in manhole cover (1) Optic socket (Ref. SJ6W-WOGA). On bracket adjacent to monitor, not in enclosure. Ground proving device is included with the socket. (1) Thermistor socket (Ref. SJ6S). On bracket adjacent to monitor, not in enclosure. Ground proving device is included with the socket Page 3 of 6

4 Ground: Ground Ground (2) Single static ground lugs. Mount (1) on flashing rail, curbside, at centerline Mount (1) on bumper B19. Brake Interlock Curbside cabinet door activates (1) brake interlock valve. B20. Overfill Interlock None Rear vapor outlet to have separate interlock valve B21. Miscellaneous (1) Protective enclosure for manhole. Cannot be vapor tight. OEM enclosure should be functionally the same as HTS design. See attached photo and Pemex drawing. C. ACCESSORIES C1. Ladder Rear aluminum ladder, center of head, with serrated rungs and platform top step. Step below bumper C2. Walkway Adhesive backed, skid-resistant tape between flashing rails. Walkway drains through rear ladder C3. Hose Carriers None C4. Stick Tube None C5. Cabinets (1) 33"W x 30"H x 28"D aluminum cabinet, single door, stainless steel hinge Mounted curbside in front of rungear frame D-ring latch and welded sealing brackets for additional security C6. Splash Guard Front and rear, HEIL, anti-sail, anti-spray flaps. C7. Fenders (2) Single contour front fenders. (2) Double contour rear fenders. (4) Bolt on fenders for export. C8. Placards\Doc. Holders Location(s): (3) Label Master #80SM "Slidemaster" single piece placard holders and brackets. (1) placard on curbside rear fender (1) placard on streetside rear fender (1) placard mounted facing rear. C9. Lights 12 Volt Truck Lite flange mount LED lamp system complying to FMVSS with conspicuity markings each side and rear. Combination mid-tank clearance and turn signals, one each side One oval third stop light, located rear center of trailer. (2) Aluminum light boxes at rear, one each side of tank. C10. Wiring (1) 7 way ATA (#SAE J560) connector in nose box Located at lower streetside front head Page 4 of 6

5 12 Volt system, 7 wire, molded conduit throughout All connections made in junction boxes C11. Miscellaneous Tire carrier, steel basket type, mounted streetside front. Fire extinguisher bracket mounted streetside front. (2) Flag holders Location(s): (1) streetside and (1) curbside at the extreme rear outside corner of the rear fenders (reference drawing # ). D. CHASSIS D1. Upper Fifth Wheel Heavy Duty hi-tensile steel, bolted and adjustable with 2" forged kingpin. Kingpin setting to be 36 D2. Skid Plate Aluminum skid plate. D3. Landing Legs Jost model A-HEIL magnum 2-speed, sealed gear box with arctic grade grease, 70,000 lbs. rated lift capacity with 10 x 12 sand shoes and street side crank. D4. Landing Legs Finish Powder coat gray finish for improved durability. D5. Suspension Heil s R2R value package includes Hendrickson AAT 30K air ride suspension & brake system, 77.5" track 5.75 diameter axle, parallel spindle, 30,000 lb. beam rating, 49" spacing, with single leveling valve. D6. Suspension Finish D7. Suspension Frame Bumper: (RIG) Underride: D8. Suspension Frame Finishing Suspension Towers painted DuPont Imron Gray Integrated axle painted DuPont Imron Gray Hi-tensile steel subframe. Suspension bolted to subframe. Pintle hitch frame with air and electrical connections Aluminum DOT compliance bumper per FMVSS223 Underride is typically not required per wheels back exemption; however, it will be added if required by suspension location. Steel suspension frame painted DuPont Imron Gray D9. Brake System Aluminum tank air system meeting FMVSS 121 requirements ECU Configuration: Glad Hands Constant Power: Wabco 2S/1M ABS 16.5" x 7" (quick change) S-cam type drum brake system Philips "Quick Release" gladhand on service line. Auxiliary, blue circuit, center pin of SAE J560 7-way. Page 5 of 6

6 D10. Brake Chamber OEM type parking-emergency spring brake D11. Brake Lining OEM brake lining D12. Slack Adjuster OEM slack adjuster D13. Drums (4) Cast - outboard mount brake drums (16.5" x 7"). D14. Axles (2) Integral with air ride D15. Paint Unless otherwise specified, steel parts will be painted DuPont Imron 5000 series gray. D16. Accessories Install English and Spanish decals D17. Miscellaneous None E. HUBS AND DRUMS E1. Warranty Heil s R2R 3H warranty package which includes Hendricksons s 3-year wheel end warranty E1. Hubs (4) ADI 10 Stud, hub pilot (single nut mount) hub for outboard drum E2. Oil Seals Preset bearings with premium oil seals for Heil's R2R package F. WHEELS F1. Wheels (8) Customer to specify G. TIRES G1 Tires (8) Customer to specify H. MISCELLANEOUS H1. Customer None Supplied Parts H2. Warranty Heil s 3 year limited BRONZE Warranty - one year bumper to bumper coverage with some other areas being pro-rated up to 3 years. Heil s value package includes Jost s 5 year maintenance free landing gear warranty. Heil s value package includes Civacon s 3 year System3 component warranty. Heil s value package includes Dupont s prorated 3 year warranty on steel parts and prorated 4 year warranty on aluminum parts. H3. Notes Operational manual and information CD is included and shipped with each trailer. H4. Other None Page 6 of 6