ATMAPC 67 ATMAPC 710

Transcription

1 ATMAPC 67 ATMAPC 710 Four-Post Screen Printer (new G6 version) ( This photo is for reference only ) ISO 9001 & ISO14001 認證通過 1993~2004 年榮獲台灣精品獎 2000 年榮獲小巨人獎 1997 年榮獲創新研究獎 歐洲安全規格認證 國家磐石獎 1996 年榮獲台灣產品形象銀質獎 248 台灣台北縣五股工業區五權七路 65 號 65, W uchuen 7th Roa d., W uku I nd. Z one, T aipei, T aiwan, 248 Tel : Fax: Web : E - mail: 1

2 APPLICATION : Suitable for precision screen printing on rigid and flexible non-deforming material flat film / sheet / thin board, such as Mylar Overlay, Name Plate, Poster, Sticker, Decal, Sign, Flexible Circuit, etc. CHARACTERISTIC : Stencil Structure Adopted German motor + chain to transmit four-post synchronously with encoder digital control screen level positioning. Mechanism of screen vertical leveling adjustment is equipped at four corners of lateral left and right frame holder, enable to adjust screen leveling individually to compensate mesh tension and to secure mesh parallel with table surface. Screen frame holder is equipped with registration pin at rear side to achieve quick positioning at center location. Air locking is equipped for screen micro-adjustment and frame holder to obtain fast installing / removing screen as well as positioning. And check valve is attached to secure locking while air and power supply is terminated at abnormal condition. Preset servo peel-off avoids screen mesh to get stuck with substrate, speed and height and distance (start / end point) of peel-off can be preset thru touch-screen to coordinate with synchronous printing stroke. GERMAN MOTOR + ENCODER 2

3 Quick Positioning Screen Frame Insert Quick Lock EASY TO ADJUST 3

4 Table Structure German motor + swivel arm to drive sliding table in/outward leaded by Linear Guide Rail to achieve accurate positioning within ± 0.05 mm. Linear Guide Rail is protected and supported by new type high rigidity Aluminum extrusion profile, mounting surface was machined precisely to secure extreme parallel. Aluminum alloyed table top lamination achieves extreme strength and accurate even flatness (tolerance of flatness within ±0.10mm) Vacuum hole sizeψ1.5mm with pitch 20x20mm to assure substrate flatness laid on table top. Printing Structure Fast and precise printing stroke is driven by servomotor, which is directly connected the driving pulley without tolerance to generate the best efficiency of transmission. Enables to preset speed and distance of squeegee / flood coater traveling thru touch-screen panel. Speed and Stroke to be controlled by Servomotor Air Pressure Equalizing System 4

5 Safety Device In case of front safety bar is not at home position, sliding table doesn t come out to protect operator health and safety. (bilateral sides of machine and front of both sides are equipped with safety bar to protect operator safety.) Screen cleaning button switch is located at rear side of guide rail profile for sliding table, which is pressed to stop machine operation to protect operator cleaning screen at rear side. Safety Bar Screen Cleaning Push Button FRL unit with auto pressure detection, insufficient air pressure source may cause to stop machine running in order to secure all printing to be done in condition of sufficient air pressure. Light on for insufficient air pressure 5

6 Electrical System Adopts 7 inch colored touch-screen for versatile setting various function and parameters, quick save and retrieve 100 groups of memory to obtain the digitalized control printing quality. Safety guard loop, if setting or operation was failed or malfunction, machine stops immediately, error message and restoration icon are shown onto touch-screen. 7 inch touch-screen panel with graphic UI Special Option : Dripless squeegee (swivel type) : If dripless squeegee is applied, squeegee swings onto flood coater to prevent residue ink drip onto mesh to cause uneven ink spot. Anti-static bar : before table enters into printing section, static on substrate surface can be eliminated. Adhesive paper tape roller : before table enters into printing section, dusts or particles on substrate are removed to secure printing quality. Gripper take-off : pneumatic registration pins will be added onto table top at location next to each gripper, if optional gripper take-off is required. 6

7 Specification : Descriptions ATMAPC 67 ATMAPC 710 Table size (WxD mm) 800 x x 950 Pneumatic pins 6 pcs (square shaped) 7 pcs (square shaped) Vacuum area (WxD mm) 740 x x 760 Max printing area (WxD mm) 750 x x 750 Max frame O/D size (WxD mm) 1100 x x 1250 Min frame O/D size (WxD mm) 900 x x 900 Frame height ( mm ) 25 ~ 45 Screen fine adjustment ( mm ) X/Y = ±10 ; Z = ± 2 Peel-off height ( mm ) 25 Peel-off type Preset servo peel-off on touch panel Screen cleaning height ( mm ) 350 Substrate thickness ( mm ) 0 ~ 30 mm ( 3/4 auto : 0 ~ 4 mm) Working table height ( mm ) Print head speed ( mm/ sec ) 50 ~ 1250 Max. capacity (pcs / hour) 850 P/H (3/4 auto : 780 P/H) ±4 Print head skew angle ±5 ±4 Pneumatic type gripper 4 pcs 5 pcs Conveyor speed ( mm / sec ) Compressed air source 5 ~ 7 kgf / cm² Power source 220 / 380V, 50 / 60 Hz Machine dimension ( cm ) 164 x 245 x x 275 x 143 Control panel Touch screen control panel 7