Dual Post Horizontal Band Saw Model H-18A USAGÉE 2003 FABRICATION NORD AMÉRICAINE

Transcription

1 FABRICATION NORD AMÉRICAINE PROMAX MACHINERIE INC. 255-N Chemin du Tremblay Boucherville, Québec, J4B 7M1 Tel : Fax :

2 TECHNICAL SPECIFICATIONS Capacity 90 Blade Size: Blade Drive: Blade Speed: Hydraulic Drive: Hydraulic Tank Capacity: Coolant Tank Capacity: Shuttle Stroke: Vise Control: Table Height: Workload: Machine Weight: Dimensions (w x l x h) Rectangular 18 x /2 x HP SFM 3 HP 9.5 US GAL. 30 US GAL multi-indexing Hydraulic 31 10,000 lbs 8,500 lbs 127 x 88 x 92 Round 18 standard MACHINE CONSTRUCTION & FEATURES Machine Base - The machine base is designed and produced with electro-welded steel components for maximum rigidity and support. A chip removal auger and 30 US gallon coolant tank are built into the base. Leveling bolts are located at corners of the machine. 10 HP Motor - Heavy-duty 2-stage gearbox and 10 HP motor, which is controlled by an AC inverter drive. Blade speed is easily adjusted from the control console and the wide range of available band speeds allows for efficient cutting of many types of material. Blade Wheels - High quality cast iron wheels with heavy-duty wheel & gearbox shaft bearings. Blade Guides - Replaceable carbide insert guides housed in two heavy duty cast iron guide arms provide cut accuracy of + / per linear inch of material and excellent vibration dampening. Saw guides are automatically set hydraulically. The idler side guide arm is mechanically connected to the front vise moveable jaw and moves in tandem with the opening and closing of the jaw. This provides proper positioning of the guide arm spacing, in relation to material width, at all times. Vising Full capacity, full stroking hydraulic vises with replaceable wear strips provide for efficient vise loading with minimal material vibration. Powered Blade Brush - driven off the blade drive wheel keeps the blade gullets clean, helping to maximize blade performance and life. Blade Tensioning - Hydraulic blade tensioning provides consistent automatic blade tension while allowing quick and easy blade changing.

3 Coolant System - A centrifugal pump immersed in the 30-gallon coolant reservoir delivers ample coolant flow through carbide faced and nozzle guides. Flow cocks are present for coolant quantity adjustment. Work Light A halogen work light provides substantial lighting over work piece / cutting area. Blade Breakage Switch If the blade breaks during operation the machine will be shut down. Hydraulically Driven Chip Auger Built into the base, an auger screw pulls chips from the base and discharges at side of machine. High Resolution Feed Rate Valve - A critical feature when cutting hard to machine materials (special alloys) when a constant feed rate is a necessity. The valve incorporates two multi-turn feed rate control knobs, an extra fine micrometer style and a fine metering valve that offers finer control than the conventional valve. During cutting only one feed control valve is used and the second should be closed. Hydraulic System - A 3HP driven hydraulic pump supplies system pressure. The system pressure through 3-position directional valves controls all vising, head up/down, blade tension, and guide arm and shuttle movement. The pump and motor assembly and hydraulic manifold complete with all function directional valves all swing out with the hydraulic compartment door for easy service access, and minimal downtime. Hyd-Mech s Direct Down feed- (DDF) Provides easy adjustment of both head feed rate and cutting pressure. Machine sawing chart provides proper blade speed, tooth pitch, feed rate and feed force recommendations. Saw head control includes fast approach control feature for quick set ups. Feed rate is displayed on PLC in linear inches per minute during the sawing operation via rotary encoder. Electrical System - The electrical control components are housed in a cabinet at the left rear side of the machine. The operator manual switches and PLC control are conveniently located on a console in the front of the machine. Components and wiring are neatly laid out and labeled for easy troubleshooting. Controls Conveniently located in the front of the machine, to the right of the out feed table, the selector switches and pushbuttons allow the operator to manually control all machine functions including emergency stops. The Mitsubishi PLC 100 controls the Automatic cycle. The operator enters job information through the PLC interface keypad. The information required will be desired part length and quantity of pieces. Up to 99 different jobs can be entered into the PLC memory, and can be called up and performed at any time. Also, a job queue function allows up to 5 jobs to be picked from the memory, and run consecutively. Some unique features of the PLC100 control are blade chamber, which separates the cut part to allow for more back clearance (excellent for carbide blades); adjustable power down timer; coolant saver; trim cut on or off; automatic blade kerf compensation. In Manual mode - The PLC displays blade speed, feed rate and length system readout. A single part operation can also be performed while in the Manual mode. The operator simply enters the desired part length, presses the cycle start button, starts the blade, and the machine will index that length, cut it off and raise the head back up. In Automatic mode - The PLC displays blade speed, feed rate, shuttle vise position, part length, quantity required, and number of pieces cut. Blade Drive - The blade drive motor is controlled by a Mitsubishi AC inverter drive. Provides smooth operation and infinite adjustment from 50 to 350 sfm.

4 OPTIONAL FEATURES Full Capacity Overhead Bundling - Hydraulically powered overhead clamp that moves down on the material from above. Its downward (clamping) and upward (unclamping) movement are controlled and timed with the opening and closing of the side vise. Very effective, and necessary for bundle cutting various material shapes & sizes. Can also be effective in dampening of cutting vibration. Out of Stock Switch - Mounted on the shuttle vise, when the vise closes with no material between its jaws, the machine hydraulics will shut down. (The cut in progress at the time of the switch being tripped is finished before shut down occurs) This option allows the machine to be left unattended with no danger of the machine continuing to cycle with no material left. Vertical Rollers - Two 3 diameter rollers mounted vertically at each side of the end of machines in feed conveyor. Assists in material alignment. Variable Vise Pressure - Allows for adjustment of the clamping pressure of both vises. Recommended for thin wall tubing and other light material applications where standard vise pressure may deform the material Laser Light Projects a crisp line of laser light along the blade line. This feature can be used for fast length measurements or as a cut marker. Mist Lubrication System Air mist system providing blade lubrication and cooling. Alternative to standard flood system. Note: Ordering this option does note eliminate the standard flood coolant system. Idler Roller Conveyors - Type II Conveyor: 26 wide x 31 high Maximum Workload 10,000lbs Available in 5 or 10 lengths. Welded in butt couplers allow sections to be bolted together to form longer lengths as necessary. Powered Roller Conveyors - Type II Conveyor: 26 wide x 31 high Maximum Workload 10,000lbs Available in 5 or 10 lengths. Welded in butt couplers allow sections to be bolted together to form longer lengths as necessary Includes gearbox, drive sprockets, and chain. 3 position, forward/stop/reverse control with choice of variable speed control (0-30 fpm) or fixed speed (30 fpm), mounted on remote pedestal with 10 chord 2 HP VFD is synchronized with machine shuttle movements on automatic machines (NOTE: If more than 30 of powered sections are to be coupled together, extra drive capability may be required contact Hyd-Mech for details/pricing)

5

6

7 CONDITIONS OF SALE H-18A, USED 2003, S/N B S CDN$ $ 35, CDN PRICE FOR EQUIVALENT SAW NEW: $72, CDN OPTIONS : Full Capacity Hydraulic Overhead Bundling (2 étaux, valeur $4,800) INCLUDED TERMS & CONDITIONS OF SALE TERMS : 100% ON DELIVERY F.O.B. : PROMAX, BOUCHERVILLE VOLTAGE : 575V DELIVERY : 1-2 WEEKS TRAINING : 4 HOURS INCLUDED IN PRICE WARRANTY : 3 MONTHS ON PARTS AND LABOUR (EXCLUDING NORMAL WEAR PARTS) OFFER VALID FOR : 30 DAYS Luc Marion Directeur des ventes Bur : lmarion@promaxmachinerie.com 255-N, chemin du Tremblay, Qc, J4B 7M