Rack & Panel Rectangular Miniature Subminiature Environmental Removable Contacts

Transcription

1 Rack & Panel Rectangular Miniature Subminiature Environmental Removable ontacts Table Of ontents Series Description Page MR Miniature Rectangular onnectors With Removable ontacts 2-10 X External Miniature Rectangular onnectors With Removable ontacts TMR TX Heavy Duty, Industrial and ommercial, Miniature Rectangular Rack and Panel onnectors With Removable ontacts Heavy Duty, Industrial and ommercial, External Miniature Rectangular Rack and Panel onnector With Removable ontacts MR Miniature Rectangular / #16 ontacts /.062" Dia. / 13 mps MRE Miniature Rectangular / #20 ontacts /.040" Dia. / 7.5 mps XMR and XMRE External Miniature Rectangular / #16 ontacts /.062" Dia. / 13 mps #20 ontacts /.040" Dia. / 7.5 mps SLE, SME and SRE.030" Dia. / 5 mps.040" Dia. / 7.5 mps Sub Miniature / High Density Rectangular /.025" Dia. / 3 mps SRE Sub Miniature Rectangular onnector With Removable ontacts Panel Mount Miniature / 22 WG /.030" Dia. / 5 mps SRM Sub Miniature Rectangular / #20 ontacts /.040" Dia. / 7.5 mps PM1 High Voltage, Single ontact / #20 ontacts /.040" Dia. / 7.5 mps 71 PM6 High Voltage Miniature / #20 ontacts /.040" Dia. / 7.5 mps 72 SM Sub Miniature / #20 ontacts / 3 and 7.5 mps M High Voltage Miniature / #20 ontacts /.040" Dia. / 7.5 mps JF Miniature Side Mount / #20 ontacts /.040" Dia. / 7.5 mps JF Miniature Side Mount / #16 ontacts /.062" Dia. / 13 mps Removable ontacts Tools and ccessories Locations Global Sales Support 94 ontact a Winchester Electronics sales representative for your V.35 Rack & Panel Data ommunications onnectors While the information in this publication is believed to be accurate and reliable, all data presented is subject to change without notice. Winchester Electronics disclaims responsibility for any damages resulting from application or any incompleteness or inaccuracies in the information presented. onsult factory for specific information on the latest design specifications. 1999, Winchester Electronics RP / 1

2 MR Series Miniature Rectangular, Removable ontacts FETURES losed Entry Removable Socket and Pin ontacts. onnector Inserts with 9 to 104 ontacts. Quick rimp... Snap in Place! To remove... insert removal tool Push Out ontact! Removable contacts offer a substantial savings of time, labor and a great flexibility in the choice of circuitry. The contact is easily removed with the hand tool depicted and then placed by hand or with a simple insertion tool. The MR Series is an important extension of the MR line featuring a variety of crimp and solder removable contact styles. Except for body thickness, they are similar and interchangeable with the MR Series. SPEIFITIONS MILITRY ROSS REFERENE urrent Rating: Up to 13 amps No. of ontacts: 9, 14, 18, 20, 26, 34, 41, 42, 50, 66, 75, 104 ontacts: ontact Identificaiton: Must be ordered separately. Select from crimp, solder, dip solder, shielded or Wire- Wrap termination contacts. See 100 Series contact section. Standard contact identification is alphabetical except for MR66 and 75 which have numerical identification. To order numerical identification on MR 34, 50 or 104, specify MN**P or S. Electrical Data: Meets high potential performance of MIL The dielectric withstanding voltage is one minute electrification at 2000 V (sea level). Dielectric: MR Series: Standard glass filled diallyl phthalate, per MIL- M-14, SDG-F, color gray. Qualification: Military Versions are QPL d to M28748/3 and M28748/4. Polarization: Gold plated guides provide positive polarization. Polarized nickel-plated brass and/or passivated stainless steel with anodized aluminum knobs available. Hoods: nodized aluminum. May be applied to either plug or receptacle. oth top and side opening hoods available. TLOG NO. MR 9P MS MR 9S MS MR 14P MS MR 14S MS MR 20P MS MR 20S MS MR 26P MS MR 26S MS MR MS34P MS MR MS34S MS TLOG NO. MR 42P MS MR 42S MS MR 50P MS MR 50S MS MR 66P MS MR 66S MS MR 75P MS MR 75S MS MR 104P MS MR 104S MS RP / 2

3 MR Series Miniature Rectangular, Removable ontacts Dimensions are for reference only and are subject to change. Outline drawings on request UN 2 THD..81 Drawings and corresponding part numbers show G type guide sockets. It is recommended that guides be used wherever Slot.038 Wide UN 2 THD possible for positive polarization and for protection of contacts except for the MR 104 where the jackscrew locking device is recommended Slot Wide R R.130 MR 9S-G MR 9P-G MR 14S-G MR 14P-G 4-40 UN 2 THD Slot.038 Wide R UN 2 THD Slot.038 Wide R.13R.52.09R.13R MR 18S-G MR 18P-G MR 20S-G MR 20P-G PHYSIL DT GUIDE SOKETS Plug Recepticle No. of Wt. in Ozs. ode ode ontactsw/o ontacts No. No. Plug Rec. MR9P MR9S MR14P MR14S MR18P MR18S MR20P MR20S MR26P MR26S MR34P MR34S Plug Recepticle No. of Wt. in Ozs. ode ode ontactsw/o ontacts No. No. Plug Rec. MR41 MR41S MR42P MR42S MR50P MR50S MR66P MR66S MR75P MR75S MR104P MR104S How To Order: To obtain K or N guides in place of the standard G type, substitute the desired socket style code letter ( K or N ) for G in both the Plug and Receptacle ode Numbers. Guide Socket ode Letter G* ctual Size Photo For General Use Phosphor ronze K* For High Electrical onductivity eryllium opper Standard Guide Pin mates with all types rass N* For Extra Mechanical Strength rass * For passivated stainless steel add SS suffix RP / 3

4 MR Series Miniature Rectangular, Removable ontacts Dimensions are for reference only and are subject to change. Outline drawings on request. Typ UN 2 THD Slot.038 Wide Typ R 4-40 UN 2 THD Slot.038 Wide Mounting holes for number 4 machine screws R.13R.130 Typ Typ MR 26S-G MR 26P-G MR 34S-G MR 34P-G Typ UN 2 THD Slot.038 Wide Typ R 4-40 UN 2 THD.86 Slot Wide Mounting holes for number 4 machine screws R R Typ.180 Typ MR 41S-G MR 41P-G MR 42S-G MR 42P-G Drawings and corresponding part numbers show G type guide sockets except for the MR104P and S which show JT hardware. Mounting Note: onnectors MR 26, MR 20 and smaller, use guides for mounting in a hood or on a panel. onnectors MR 34, MR 42, MR 50, MR 66, and MR 75 use four #4 machine screws, in addition to guides, for mounting in a hood or on a panel. Guides are not recommended for use with MR 104. MR 104 uses four #6 machine screws for mounting. *For numerical contact identification instead of alphabetical, order MN. P or S available in sizes 34, 50 and 104. Example MN 34P. MR 66 and 75 have numerical contact identification as standard. RP / 4

5 MR Series Miniature Rectangular, Removable ontacts Dimensions are for reference only and are subject to change. Outline drawings on request..47 Typ UN 2 THD Slot.038 Wide Typ 4-40 UN 2 THD Slot.038 Wide Mounting holes for number 4 machine screws R.180 Typ Mounting holes for number 4 machine screws R.180 Typ MR 50S-G MR 50P-G MR 66S-G MR 66P-G Typ UN 2 THD Slot.038 Wide Typ Dia. holes for safety wire UN 2 THD UN 2 THD. Mounting holes for number 4 machine screws R Typ Mounting holes for number 6 machine screws R.180 Typ MR 75S-G MR 75P-G MR 104S-JT * MR 104P-J Drawings and corresponding part numbers show G type guide sockets except for the MR104P and S which show JT hardware. Mounting Note: onnectors MR 26, MR 20 and smaller, use guides for mounting in a hood or on a panel. onnectors MR 34, MR 42, MR 50, MR 66, and MR 75 use four #4 machine screws, in addition to guides, for mounting in a hood or on a panel. Guides are not recommended for use with MR 104. MR 104 uses four #6 machine screws for mounting. *For numerical contact identification instead of alphabetical, order MN. P or S available in sizes 34, 50 and 104. Example MN 34P. MR 66 and 75 have numerical contact identification as standard. RP / 5

6 MR Series Miniature Rectangular, Removable ontacts JKSREWS & JKSOKETS Dimensions are for reference only and are subject to change. Outline drawings on request. Polarized jackscrews give the ease and assurance of threaded positive coupling. The actuating side consists of two turnable screws, one male and one female, each with knurled and slotted knobs. On the mating half are the two fixed screws required to complete the locking action. When mated, the jackscrews may be locked with a safety wire through the hole in the self-locking pin (in the jackscrew shaft) UN except size 104/6-32 UN Jacksocket 6-32 UN THD. except size 104/8-32 UN Mono- Side able Opening Opening Jackscrew Side able Top able Opening Top able Opening Jackscrew onnector with fixed Jackscrews ode designation: J DIMENSIONS D ND Mating connector half with turnable Jackscrews-with-Knobs. ode designation: JT.16 Self Locking Hood Pin E OR Mating connector half with Hood and turnable Long Jackscrews-with- Knobs. ode designation: JT H, JT H1 Mono- 052 Dia. Safety Jacksocket Wire Hole F OR Mating connector half with Hood and turnable Monojacks. ode designation: JTDH, JTDH1 onnector Dimension Dimension Dimension E Dimension F Size H H1 H8 H9 H13 H H1 H8 H9 D H H1 H8 H9 H13 H H1 H8 H9 MR MR MR MR MR MR MR MR MR MR MR MR New Monojacks ssemble and Disassemble With Remarkable Ease and Speed To free the connector from the hood, simply remove four screws. Monojacks may be used on miniature rectangular connectors with from 34 to 104 contacts and with molds featuring guide hole and two mounting holes on both ends. Molds have 2 center thru holes and 4 mounting holes. RP / 6 MOLDINGS HVE STRIGHT THRU HOLES MONOJKS RE PTIVTED IN KEYHOLE SLOT OF HOOD S SHOWN OVE. WHEN USING SHELLS, MONOJKS RE PTIVTED IN KEYHOLE OF SHELL ND LERNE HOLES RE PLED IN HOODS.

7 MR Series Miniature Rectangular, Removable ontacts JKSREW & JKSOKETS Dimensions are for reference only and are subject to change. Outline drawings on request..19 Dia..22 Dia Dia..078 INT. HEX..25 HEX. JTW JTU JTX JTZ.19 Dia..22 Dia INT. HEX HEX. JTW JTU JTX 6-32 UN 2 THD. () UN 2 THD. DIMENSIONS Hood Type ll jackscrews and sockets are stainless steel, passivated except J & JTD which are nickel plated brass. ll knobs are aluminum, anodized except JTW and JTW which are stainless steel, passivated. JZ Size Type JTW H H1 H8 H9 H13 Dimension Size Type JTU Size Type JTX Size H H1 H8 H9 H13 H H1 H8 H9 H13 Dimension Dimension Type JTZ H H1 H8 H9 H13 Dimension RP / 7

8 MR Series Miniature Rectangular, Removable ontacts FORMED LUMINUM HOODS Dimensions are for reference only and are subject to change. Outline drawings on request. Hoods shown are MRE Hoods for use with MR onnectors DIMENSIONS Formed Hoods for MR onnectors are available in top and side opening for most MR onnectors - Deep Drawn Hoods are available for MR 34, MR 66 and MR 104 connectors... providing additional strength. Hoods and cable clamps are of anodized aluminum. They provide support and strain relief for the cable and may be applied to either Plug or Receptacle. Hoods may be ordered separately (see code numbers in the tables below) or assembled on connectors. Top able Opening ode No. DIMENSIONS able Opening Wt. Fits D E F G Oz. onnector MRE9H MR9 (P or S) MRE14H MR14 (P or S) MRE18H MR18 (P or S) MRE20H MR20 (P or S) MRE26H MRE26H MR26 (P or S) MRE34H D.6 MRE34H MR34 (P or S) MRE41H MR41 (P or S) MRE42H D.7 MRE42H MR42 (P or S) MRE50H D.8 MRE50H MR50 (P or S) MRE75H MRE75H MR75 (P or S) RP / 8 Side able Opening able ode DIMENSIONS Opening Wt. Fits No. D E F G Oz. onnector MRE9H D.3 MRE9H MR9 (P or S) MRE14H D.3 MRE14H MR14 (P or S) MRE18H D.3 MRE18H MR18 (P or S) MRE20H D.3 MRE20H MR20 (P or S) MRE26H MRE26H MR26 (P or S) MRE34H D.6 MRE34H MR34 (P or S) MRE41H MR41 (P or S) MRE42H MRE42H MR42 (P or S) MRE50H MRE50H MR50 (P or S) MRE75H MRE75H MR75 (P or S)

9 MR Series Miniature Rectangular, Removable ontacts VIRTION LOKS Lock Tabs (MRE-V shown) Lever & Pivot ssemblies (MRE-VL shown) Nomenclature Lever & Pilot ssembly MRE-VL MRE-VL2 Lock Tabs (See Note) MRE-V MRE-V2 Used on onnectors MR 9, 14, 18, 20, 26, 34, 41, and 42 MR 50 MR 75 DIMENSIONS / DRWN LUMINUM HOODS Designed for MR connectors, this vibration lock features genuine simplicity of design, plus complete locking effectiveness. ssembly of either the lever-and-pivot assembly or the lock parts to the plug and receptacle is quick and easy. The unit locks automatically when the mating plug and receptacle are engaged. Unlocking and disengaging can be done with one hand. Note 1:When panel mounting the lock-tab half of a MR 34, MR 42 or MR 50 connector, flat washers (.033 minimum thickness) should be used on the mounting screws to shim the molding away from the panel. Note 2: Each code number indicates two units, i.e., the MRE-VL consists of two levers and two pivots (unassembled*), and the MRE-V consists of two tabs. Note 3: These units are supplied unassembled to facilitate handling. The pivot is easily assembled to the lever merely by inserting the hooked end through the lever opening. It will automatically snap into proper position. Patent #2,760,174. Hoods shown are MR Hoods for use with MR onnectors DIMENSIONS - Top Opening Wt. Fits ode No. Oz. onnector D E H G MR 34H x MR 34P MR 34S MR 66P MR 66H Dia MR 66S MR 104P MR 104H Dia MR 104S Dimensions are for reference only and are subject to change. Outline drawings on request..08 D DIMENSIONS - Side Opening Wt. Oz. ode No. D E H G MR 34H x MR 66H Dia MR 104H Dia For MR; 66; Dia. 2 Holes (.228 Dia. 2 Holes For 104) Fits onnector MR 34P MR 34S MR 66P MR 66S MR 104P MR 104S H DIMENSIONS / MOUNTING RKETS.08 Top able Opening G E able Opening For MR 34 Only.08 G D Side able Opening E able Opening H E F G ode No. DIMENSIONS D E F G H.128 Dia 3 Holes MRE (No. 4 Mounting Screw) Wt. Oz..4 D MRE Dia 3 Holes (No. 6 Mounting Screw).6.11R Panel Opening MR 50 and MR 75 connectors use the standard MRE 50 and MRE 75 mounting brackets. RP / 9

10 MR Series Miniature Rectangular, Removable ontacts ORDERING INFORMTION Omit steps not required MR 34 S G H VL Step 1 Series: MR MN Numerical contact identification on sizes 34, 50, and 104. Step 2 Number of ontacts: 9, 14, 18, 20, 26, 34, 41, 42, 50, 66, 75, 104 See note 1 below. Step 3 ontact Designation: P - Pin S - Socket When ordering moldings less hardware to be used with monojacks, see note 2 below. Step 4 Guides and Jackscrew Locks: (See bottom hart) Step 5 Hoods: H - Standard top opening. Sizes 26 thru 104 only. H1 - Standard side opening. vailable all sizes. H8 - Large top opening. Sizes 26 thru 104 only. H9 - Large side opening. vailable all sizes. H13 -Large top opening, high hood. Sizes 9, 14, 18 & 20 only. Step 6 Vibration Locks: Step 7 Special V - Lock Tab Options: V2 - Lock Tab onsult Sales (Size 50 Department & 75) VL - Lever & Pivot ss y VL2 - Lever & Pivot ss y (Size 50 & 75) Step 4 Guides G* Phosphor ronze ylindrical Guides K eryllium opper ylindrical Guides N* rass ylindrical Guides Guides are not recommended for Size 104 P indicates two guide pins or two jackscrews (EX. JTP) S indicates two guide sockets or two jacksockets (Ex. GS) Jackscrew Locks ***J Polarized Fixed Jackscrew and Jacksocket JT Polarized Short Turning Jackscrew and Jacksocket JT Polarized Long Turning Jackscrew and Jacksocket *** JTD Polarized Long Turning Mono-Jackscrew and Mono-Jacksocket for Sizes 34, 42, 50, 66, 75, and 104 only. **JZ Same as J but with 6-32 mtg. thd. (Std. on 104) **JTW Same as JT but with knurled round knob with internal hex (not avail. 104) **JTU Same as JT but with knurled round knob with screwdriver slot (not avail. 104) **JTX Same as JT but with hex knob (not avail. 104) **JTW Same as JT but with knurled round knob with internal hex (not avail. 104) **JTU Same as JT but with knurled round knob with screwdriver slot (not avail. 104) **JTX Same as JT but with hex knob (not avail. 104) **JTZ Same as JT but with prybar knob (not avail. 104) * For passivated stainless steel add SS suffix. ** Request availablity information. ***Material: Nickel Plated rass standard Notes: 1. ontacts are ordered separately. See 100 Series contact section of Rack & Panel 2. When ordering molding less hardware and hood for use with JTD Monojacks, connectors must be ordered as follows: Pin connector = MR 34P8, MR 42P8, etc. Socket connector = MR 34S8, MR 42S8, etc. The number 8 indicates special housing for use with the JTD Monojack hardware (available on sizes 34, 42, 50, 66, 75 and 104). RP / 10

11 X Series External Miniature Rectangular, Removable ontacts X34SF2010 X34PM1000 X34P1700 SPEIFITIONS Designed for external installation, the X is the MR removable contact connector equipped with protective shells and mounting plates for chassis or cable mounting on metal containers, bulkheads, or any outside surface equipment. Lighter and smaller than other external connectors, they provide dependable service under adverse conditions. Inserts are housed in protective shells and there is screw lock coupling of plug and receptacle. urrent Rating: Up to 13 amps No. of ontacts: 9, 14, 18, 20, 26, 34, 42, 50, 66, 75, 104 ontacts: ontacts must be ordered separately. Select from crimp, solder, dip solder, shielded or wire wrap terminations. Electrical Data: Meets high potential performance requirements of MIL The dielectric withstanding voltage is one minute electrification at 2000 V. Military versions are QPL d to M28748/3 and M28748/4. TLOG NO. X9-0300X MS T8 X X MS T1 X X MS T2 XMRE9-0400X MS S8 XMRE X MS S1 XMRE X MS S2 XMRE X MS18192-T9 XMRE X MS S9 XMRE X MS18192-T3 XMRE X MS S3 XMRE X MS T4 XMRE X MS S4 XMRE X MS18192-T5 XMRE X MS S5 XMRE XP MS T6 XMRE XS MS TXX Dielectric: Polarization: ccessories: TLOG NO. XMRE XS MS 18192SXX XMRE XP MS S6 XMR MS T1 XMR MS S1 XMR MS T2 XMR MS S2 XJTMS605P MS XJTMS605S MS XJTMS608P MS XJTMS608S MS XJTMS605P MS XJTMS605S MS XJTMS606P MS XJTMS606S MS XJMS602P MS XJMS602S MS Diallyl Phthalate, MIL-M-14, Type SDG-F, olor Gray Seven positions available for pin and slot polarization on shells. dditional polarization can be provided with various arrangements of jackscrews and guides. Shells, formed and drawn hoods, mounting plates, jackscrews and jacksockets. TLOG NO. XJMS603P MS XJMS603S MS XNMS700P MS XNMS700S MS XNMS702P MS XNMS702-S MS XMR MS XMR MS XMR MS XMR MS XMR MS XMR MS XMR MS XMR MS RP / 11

12 X Series External Miniature Rectangular, Removable ontacts ONNETOR SSEMLIES Self-locking pins Turnable Jacksocket Turnable Jackscrew Male Insert Plug Shell Jackscrew and Jacksocket Knobs Fixed Jackscrew Mounting Plate Receptacle Shell Female Insert Fixed Jacksocket Receptacle DEFINITIONS OF ONNETOR TERMS RP / 12 Plug: The complete connector half which has the plug shell as part of its assembly. Receptacle: The complete connector half which has the receptacle shell as part of its assembly. Shell: The metal housing in which a male or female insert is assembled. shell is either a plug shell or a receptacle shell: Plug Shell - one which is designed to be inserted into a receptacle shell. Receptacle Shell - one which is designed to receive and enclose the plug shell upon engagement. Male Insert: The molded insulator body containing pin contacts. Female Insert: The molded insulator body containing socket contacts. Pin ontacts: Male ontacts that fit into the socket contacts. Socket ontacts: Female ontacts tubular in shape, which receive the pin contacts and retain them by spring tension. Polarization: means of controlling the engagement of a plug and receptacle so that correct mating of the contacts is achieved. ccessories: Those components such as hoods and mounting plates which are attachable to a plug or receptacle to facilitate mounting and/or handling of the connector, and to prevent inadvertent cross-mating.

13 X Series External Miniature Rectangular, Removable ontacts ONTT RRNGEMENTS Dimensions are for reference only and are subject to change. Outline drawings on request. Views are rear (wiring end) of female inserts. (Male inserts are opposite.) Typ Typ Typ Typ R.172 Typ.09R.13R.130 Typ.09R.13R.130 Typ.09R.13R.130 Typ X 9 X 14 X 18 X 20 Typ.56 Typ R Typ R Typ R.13R.130 Typ X 26 Mounting Holes For No. 4 Machine Screws X 34*.180 Typ Mounting Holes For No. 4 Machine Screws.73 X Typ Mounting Holes For No. 4 Machine Screws.73.16R.180 Typ X 50*.150 Typ Typ Typ Mounting Holes For No. 4 Machine Screws Mounting Holes For No R Machine Screws.180 Typ R.180 Typ Mounting Holes For No. 6 Machine Screws R.180 Typ X 66 X 75 X 104* *For numerical contact identification instead of alphabetical, order XN**P or S available in sizes 34, 50, and 104. Sizes 66 and 75 have numerical contact identification as standard. The spacing, arrangement, and identificaion of contacts of the X inserts are the same as those found on the Series MR removable contact connectors for the same number of contacts. RP / 13

14 X Series External Miniature Rectangular, Removable ontacts JKSREW & JKSOKETS Dimensions are for reference only and are subject to change. Outline drawings on request. Views are rear (wiring end) of female inserts. (Male inserts are opposite.).73 Fixed Jackscrews (F) Long Turning Jackscrews () Used With Hoods Short Turning Jackscrews (M) Used Only Without Hoods Monojacks (D) Used With Hoods SPEIFITIONS Turnable jackscrew-jacksocket combination (M,, or D) assembles on either Plug or Receptacle; the mating connector-half (either Receptacle or Plug) must then contain fixed jackscrew-jacksocket combination (F). oth short and long turning jackscrews (M and ) have knurled and slotted knobs for locking by hand or screwdriver. Knob is assembled on shaft with hollow, removable, self-locking pin. Safety wiring of engaged halves is achieved by using the through-hole in self-locking pin in the knob. Monojacks (D) are long turning one-peice locking devices with slotted and knurled head. Shaft has through-hole for safety wire. available with hoods only, in sizes 34, 42, 50, 66, 75, and 104. Drawings show extension of standard knobs beyond shell and beyond hood. PPLITIONS Jackscrew locking device assures positive coupling of engaged connectors to prevent accidental disconnecting from vibration or physical shock. It also aids easy connection and separation of connector plug and receptacle. Mounted connector-half houses one non-turnable fixed jackscrew and jacksocket to insure connector polarization. Mating-half houses one of the three types of turning jackscrew and jacksocket (M,, or D). DIMENSIONS LOKING DEVIE SPEIFITIONS WT. OZ. ODE See Notes MTERIL ND LETTER 1 & 2 FINISH Jackscrew Nickel Plated rass Fixed F 0.15 Jacksocket } Jackscrew Short Stainless Steel with M 0.30 Jacksocket } Turnable Passivating Dip Jackscrew Long Stainless Steel with 0.45 Jacksocket } Turnable Passivating Dip Mono-Jackscrew Long Turnable D 1.07 Nickel Plated rass Mono-Jacksocket Knob Standard luminum nodized Note 1: Weights are for pairs; i.e. for a jackscrew and jacksocket, etc., so weight figure may be added once to weights of other accessories when computing total weight of plug or receptacle. Note 2: Weights of turnable jackscrews and turnable jacksockets include knob and rollpins, except mono-jackscrew and mono-jacksocket, which is a one-piece construction (shaft and knob made in one piece); weight of fixed jackscrew and jacksocket includes nuts. Standard Knobs - Extension Dimension Dimension eyond Hood X 9* 14* 18* 20* *On sizes 9, 14, 18, and 20, only large top opening hoods are available when (c) long turning jackscrews are used. atalog Number for large top opening hoods is X. Example: X X RP / 14

15 X Series External Miniature Rectangular, Removable ontacts - JKSREWS.19 Dia..078 INT. HEX..22 Dia..25 HEX Dia. W.19 Dia. U X.22 Dia. Z Dimensions are for reference only and are subject to change. Outline drawings on request..25 HEX. MW MU UN 2 THD. (TYP.) DIMENSIONS MX FZ ll jackscrews and sockets are stainless steel, passivated (except F & D which are nickel plated brass). ll knobs are aluminum, anodized except MW and W which are stainless steel, passivated. Hoods Size X 0400X Dimension Type W Dimension Type U Hoods Size X 0400X Dimension Type X Dimension Type Z RP / 15

16 X Series External Miniature Rectangular, Removable ontacts HOODS - DRWN LUMINUM Dimensions are for reference only and are subject to change. Outline drawings on request. The X Series uses standard XMR/ XMRE protective hardware. To order separately, use XMRE/XMR catalog numbers indicated DIMENSIONS Top able Opening XMR Drawn Hoods for use with X onnectors. Hoods - Side able Opening ForUse With Type Jack Sockets and Jackscrews Hood Part No. (If ordered separately) DIMENSIONS D E F G XMR x XMR D XMR D Side able Opening Type D Jack Sockets and Jackscrews Type F Jackscrews XMR D x XMR D D XMR D D XMR x XMR D 1.34 XMR D 1.63 Hoods - Top able Opening ForUse With Type Jack Sockets and Jackscrews Type D Jack Sockets and Jackscrews Type F Jackscrews Hood Part No. (If ordered separately) DIMENSIONS D E F XMR x XMR D XMR D XMR D x XMR D D XMR D D XMR x.75 XMR D XMR D RP / 16

17 X Series External Miniature Rectangular, Removable ontacts HOODS - FORMED LUMINUM Dimensions are for reference only and are subject to change. Outline drawings on request. DIMENSIONS XMRE Formed Hoods for use with X onnectors Top able Opening Hoods - Top able Opening For use with Monojacks For use with Monojacks For use with Type Jacksockets & Jackscrews For use with Type Jacksockets & Jackscrews For use with Fixed Jackscrews* For use with Fixed Jackscrews* Dimensions Hood Part No. (If ordered separately) D able Opening E Dia. F Dia. XMRE XMRE J XMRE X XMRE XJ XMRE XMRE J XMRE X XMRE XJ XMRE XMRE J XMRE X XMRE XJ XMRE XMRE J XMRE X XMRE XJ XMRE XMRE J XMRE X XMRE XJ XMRE D XMRE XMRE J XMRE XD XMRE X XMRE XJ XMRE D XMRE XMRE J XMRE XD XMRE X XMRE XJ XMRE D XMRE XMRE J XMRE XD XMRE X XMRE XJ XMRE D XMRE XMRE J XMRE XD XMRE X XMRE XJ * For use with G, K, or N guides, eliminate letter J from part number Dimensions Hood Part No. (If ordered separately) D able Opening E Dia. F Dia. Wt. Oz. (Inc. 2 able lamps and Screws) X X X XJ X X X XJ X X X XJ X X X XJ XMRE XMRE J XMRE X XMRE XJ XMRE D XMRE XMRE J XMRE XD XMRE X XMRE XJ XMRE D XMRE XMRE J XMRE XD XMRE X XMRE XJ XMRE D XMRE XMRE J XMRE XD XMRE X XMRE XJ XMRE D XMRE XMRE J XMRE XD XMRE X XMRE XJ * For use with G, K, or N guides, eliminate letter J from part number Hoods - Side able Opening Large Top able Opening Side able Opening Wt. Oz. (Inc. 2 able lamps and Screws) RP / 17

18 X Series External Miniature Rectangular, Removable ontacts SHELLS - REEPTLES Dimensions are for reference only and are subject to change. Outline drawings on request..06r.03r..140 Dia. 4 Holes.20 R..421 R. F.28.06R Mtg. Hole Style 9.14R.120 Dia. ED.384 R. ED ED ED.156 ED.06R.06R.06R.06R.06R.312 Polarizing Slot.120 Dia. 2 Holes DIMENSIONS SHELLS - REEPTLES.14R.114 G G Dia. 6 Holes For ll X For X 9 to 26 For X 34, 42, For X 66 For X 75 For X 104 onfigurations and Dia. 4 Holes G Dia. 6 Holes Important Note When Ordering Plug and Receptacle Shells The shell part numbers given in the table show an asterisk (*) where the code letter for the desired polarizing position belongs - example: XMRE9-2*000 becomes XMRE when polarization in position is desired. Specify the same position on the mating shell. For non-polarized shells, merely omit this position, e.g. XMRE TYPIL SHELLS FOR MONOJKS STYLE No Shells are.040 in. thick. Shells are aluminum, anodized for protection against corrosion. Either shell style - plug or receptacle - may be used to house the female insert, thus allowing the live socket contacts to be cable or panel mounted, as desired. Shells also provide a means by which connector polarization is accomplished - the receptacle shell is slotted for engaging a polarizing pin on the plug shell. ny of seven positions (,,, D, E, F or G) may be specified for polarization; non-polarized shells have the slot and pin omitted. RP / 18 For onnector Size 34, 42, 50, 66, R R Shell Part No. (If ordered DIMENSIONS Wt. separately) D E F G Oz. XMRE 9-2* XMRE 14-2* XMRE 18-2* XMRE 20-2* XMRE 26-2* XMRE 34-2*000 XMRE 34-4* XMRE 42-2*000 XMRE 42-4* XMRE 50-2*000 XMRE 50-4* XMR 66-2*000 XMR 66-4* XMRE 75-2*000 XMRE 75-4* XMR 104-2*000 XMR 104-4* Dia. 4 orner Holes Dia. 4 orner Holes 2 Slots 4 Slots For X 34, 42, 50, 66, For X 75 Receptacle Shell and 104 onfigurations onfiguration Style No Shells are.040 in. thick.

19 X SERIES External Miniature Rectangular, Removable ontacts SHELLS - PLUGS Dimensions are for reference only and are subject to change. Outline drawings on request..140 Dia. 4 Holes.06R.03R DE DE DE.120 Dia. 4 Holes DE.14R.06R Mtg. Hole Style 9 F R.06R.06R.06R DE.06R Dia. 6 Holes.120 Dia. Polarizing Pin G.372 R..120 Dia. G.14R.421 R..120 Dia..20 R. G Holes.120 Dia. 4 Holes 2 Holes Holes.766 For X 104 For X 75 For X 66 For X 34, 42, For X 75 For ll X and 50 For X 9 to 26 onfigurations DIMENSIONS Important Note When Ordering Plug Shells The shell part numbers given in the table shows an asterisk (*) where the code letter for the desired polarizing position belongs - example: XMRE9-1*000 becomes XMRE when polarization in position is desired. Specify the same position on the mating shell. For non-polarized shells, merely omit this position, e.g. XMRE Shells are.040 in. thick. Stainless steel shells available for 66 and 104 sizes. Dimensions vary from those shown for aluminum shells. heck sales for availability and dimensions on all sizes. TYPIL SHELLS FOR MONOJKS STYLE No Shells are aluminum, anodized for protection against corrosion. Either shell style - plug or receptacle - may be used to house the female insert, thus allowing the live socket contacts to be cable or panel mounted, as desired. Shells also provide a means by which connector polarization is accomplished - the receptacle shell is slotted for engaging a polarizing pin on the plug shell. ny of seven positions (,,, D, E, F or G) may be specified for polarization; non-polarized shells have the slot and pin omitted. For onnector Size 34, 42, 50, 66, R R Shell Part No. (If ordered DIMENSIONS Wt. separately) D E F G Oz. XMRE 9-1* XMRE 14-1* XMRE 18-1* XMRE 20-1* XMRE 26-1* XMRE 34-1*000 XMRE 34-3* XMRE 42-1*000 XMRE 42-3* XMRE 50-1*000 XMRE 50-3* XMR 66-1*000 XMR 66-3* XMRE 75-1*000 XMRE 75-3* XMR 104-1*000 XMR 104-3* Slots Dia. 4 orner Holes Dia. 4 orner Holes For X 75 For X 34, 42, 50, 66, Plug Shell onfiguration and 104 onfigurations Style No Shells are.040 in. thick. 2 Slots RP / 19

20 X SERIES External Miniature Rectangular, Removable ontacts ORDERING INFORMTION Omit steps not required X 9 P M Step 1 Series: X, XN Numerical contact identification on sizes 34, 50, and 104. Step 2 No. of ontacts: 9, 14, 18, 20, 26, 34, 42, 50, 66, 75, and 104 See note 1 below Step 3 Pin or Socket ontacts: P - Pin S - Socket Step 4 Jackscrews (See bottom chart) Step 5 Shell Type: ** 0 No shell ** 1 Plug shell, style 1 * 000. ** 2 Receptacle shell, style 2 * 000. ** 3 Plug shell, monojack type, style 3 * 000. ** 4 Receptacle, monojack type, style 4 * 000. ** 7 Stainless Steel Plug shell, style 7 * 000. ** 8 Stainless Steel Receptacle shell, style 8 * 000. ** Polarizing Position ** Request availability ** information Step 6 Polarization Position:,,, D, E, F or G. Omit letter when polarization is not required. Step 7 (See bottom chart) Step 8 Mounting Plate: 00- When no mounting plate is required *10- Mounting plate, style #0010. Note: See section XMR/E RP/57. *Mounting plates are not used with M, or D jackscrews. Step 9 Special Gaskets: Omit letter when gaskets are not required. ** G- ulkhead gasket, style #0000G. Use only when mounting plate is specified. ** F- Face gasket, style #0000F. Use with male insert only. ** - If both gasket #0000G and gasket #0000F are desired. ** heck plant for availability ** on all gaskets. Step 4 Step 7 Guides ** G- ylindrical guide with single spring member. Recommended for ground only. ** K- ylindrical guide with four spring members. May be used for electrical contact. ** N- ylindrical guide without spring member. Recommended for extra mechanical strength. Jackscrews and Jacksockets *** M- Polarized short turnable jackscrew and jacksocket. annot be used with hoods. *** - Polarized long turnable jackscrew and jacksocket for use with hoods. *** D- Polarized one-piece mono-jackscrew and mono-jacksocket (no separate knob); to be used with hoods on sizes: 34, 42, 50, 66, 75, and 104. ***F- Polarized fixed jackscrew and jacksocket usable with or without hood; (no knob required). ** MW- Same as M but with knurled round knob with internal hex. ** MU- Same as M but with knurled round knob with screwdriver slot. ** MX- Same as M but with hex knob. ** W- Same as but with knurled round knob with internal hex. ** U- Same as but with knurled round knob with screwdriver slot. ** X- Same as but with hex knob. ** Z- Same as but with prybar knob. ** Request availability information *** Material: Nickel Plated rass standard Formed Hoods: 0- No Hood. 3- Hood, top opening, style #0300, for use with Type or D jackscrews. 4- Hood, side opening, style #0400, for use with Type or D jackscrews. 5- Hood, top opening, style #0500J, for use with F style jackscrews. 6- Hood, side opening, style #0600J, for use with F style jackscrews. Deep Drawn Hoods: 7- Hood, top opening, style #0700, for use with Type or D jackscrews. 8- Hood, side opening, style #0800, for use with Type or D jackscrews. 9- Hood, top opening, style #0900, for use with F jackscrews. 2- Hood, side opening, style #0200, for use with F jackscrews. Note: ddition of X to code # indicates cable opening larger than std. See hoods for cable opening size. Example: X20P1300 X Note: 1. ontacts are ordered separately. See 100 Series contact section of Rack & Panel RP / 20

21 TMR Series TM Heavy Duty, Industrial and ommercial, Miniature Rectangular Rack & Panel onnectors, Removable ontacts TMR 34S-G TMR 34P-G Removable contacts offer a substantial savings of time, labor and a great flexibility in the choice of circuitry. The contact is easily removed with the hand tool depicted and then placed by hand or with a simple insertion tool. The TMR Series was designed specifically for the industrial/commercial customer for application in high temperature, rough service operations. This series features the same military-type anodized aluminum hoods, rugged polyester thermoplastic insulators, screw-machine removable contacts, guide and hardware as the MR Series. SPEIFITIONS Insulators: Polyester thermoplastic, black color. High potential performance: withstanding voltage is one minute electrification at 2000 V (sea level). Insulation Resistance: 500V Thermal Shock: -55 o F to +150 o F Hoods: nodized aluminum. May be applied on plug or receptable. oth top and side opening hoods available. Polarization: Gold plated guides provide positive polorization. Polarized nickel-plated brass and/or passivated stainless steel jackscrews with anodized aluminum knobs are available. Number of ontacts: Eight size connectors: 9-, 14-, 18-, 20-, 26-, 34-, 42- and 50-contact, available in either.040" or.062" diameter. ontacts: ontact Identification: Must be ordered separately. Select from crimp, solder, dip solder, shielded or Wire-Wrap termination contacts. See 100 Series contact section. Standard contact identification is alphabetical. Sizes:.040" diameter and.062" diameter contacts in 7.5-amp and 13-amp current ratings. Termination Types: rimp, dip-solder, solder removable in.040" and.062" diameter. Wire Wrap tails and stabilizing bushings for.025" and.045" square. urrent Rating: 7.5 amps maximum for.040" contacts. 13 amps maximum for.062" contacts. S ertified File No. LR34182 Recognized under the omponent Program of Underwriters Laboratories Inc. File No. E31650 RP / 21

22 TMR Series TM ORDERING INFORMTION Omit steps not required Heavy Duty, Industrial and ommercial, Miniature Rectangular Rack & Panel onnectors, Removable ontacts TMR 34 S G H VL Step 1 Insert Series ode: TMR Step 2 Number of ontacts: 9, 14, 18, 20, 26, 34, 42, 50, See note 1 below. Step 3 ontact Designation: P - Pin S - Socket When ordering moldings less hardware for use with mono-jacks, see note 2 below. Step 4 Guides and Jackscrew Locks: (See bottom hart) Step 5 Hoods: H - Standard top opening. Sizes 26, 34, 42 & 50 only. H1 - Standard side opening. vailable all sizes. H8 - Large top opening. Sizes 26, 34, 42 & 50 only. H9 - Large side opening. vailable all sizes. H13 -Large top opening, high hood. Sizes 9, 14, 18 & 20 only. Step 6 Vibration Locks: V - Lock Tab V2 - Lock Tab (Size 50) VL - Lever & Pivot ss y VL2- Lever & Pivot ss y (Size 50) Step 7 Special Options: onsult Sales Department Step 4 Guides G* Phosphor ronze ylindrical Guides K eryllium opper ylindrical Guides N* rass ylindrical Guides P indicates two guide pins or two jackscrews (EX. JTP) S indicates two guide sockets or two jacksockets (Ex. GS) * For passivated stainless steel add SS suffix. Jackscrew Locks ***J Polarized Fixed Jackscrew and Jacksocket JT Polarized Short Turning Jackscrew and Jacksocket JT Polarized Long Turning Jackscrew and Jacksocket *** JTD Polarized Long Turning Mono-Jackscrew and Mono-Jacksocket for Sizes 34, 42, and 50 only. **JZ Same as J but with 6-32 mtg. thd. **JTW Same as JT but with knurled round knob with internal hex **JTU Same as JT but with knurled round knob with screwdriver slot **JTX Same as JT but with hex knob **JTW Same as JT but with knurled round knob with internal hex **JTU Same as JT but with knurled round knob with screwdriver slot **JTX Same as JT but with hex knob **JTZ Same as JT but with prybar knob ** Request availablity information. ***Material: Nickel Plated rass standard Notes: 1. ontacts are ordered separately. See 100 Series contact section of Rack & Panel 2. When ordering hoods, hardware and connectors separately for use with JTD Monojacks, connectors must be ordered as follows: Pin connector = TMR34P8, TMR42P8, etc. Socket connector = TMR34S8, TMR42S8, etc. The number 8 indicates special housing for use with the JTD Monojack hardware (available on sizes 34, 42, and 50). DIMENSIONS ll dimensions for TMR housings are the same as MR housings. ll hoods, hardware, and accesories used on the TMR Series are the same as those used on the MR Series. See MR Series section for part numbers and dimensions. Note the TMR Series maximum number of contacts is 50. RP / 22

23 TX Series TM Heavy Duty, Industrial and ommercial, External Miniature Rectangular Rack & Panel onnectors, Removable ontacts TX34SF2010 TX34PM1000 TX34P1700 SPEIFITIONS The TX Series was designed for external installation specifically for the industrial/ commercial customer in high temperature, rough service applications. This series features the same military-type anodized aluminum hoods, rugged polyester thermo- plastic insulators, screw-machine removable contacts, guide and jack hardware, and protective, anodized aluminum shells as the X Series. These features make this Series suitable for chassis mounting, bulkheads, or any outside surface equipment. Insulators: Polyester thermoplastic, green color. High potential performance: withstanding voltage is one minute electrification at 2000 V (sea level). Insulation Resistance: 500V Thermal Shock: -55 o F to +150 o F Hoods: nodized aluminum. May be applied on plug or receptable. oth top and side opening hoods available. Polarization: Gold Plated guides provide positive polarization. Polarized nickel-plated brass and/or passivated stainless steel with anodized aluminum knobs are available. 7-position pin and slot polarization on shells. Number of ontacts: Eight size connectors: 9-, 14-, 18-, 20-, 26-, 34-, 42- and 50- contact, available in either.040" or.062" diameter. ontacts: Must be ordered separately. Select from crimp, solder, dip solder, shielded or Wire- Wrap termination contacts. See 100 Series contact section. ontact Identification: Standard contact identification is alphabetical. Sizes:.040" diameter and.062" diameter contacts in 7.5-amp and 13-amp current ratings. ontact Resistance: Termination 7.5 amps, 14 millivolts 13 amps, 10 millivolts max. rimp, dip-solder, solder removable in.040" and.062" diameter. Wire Wrap tails and stabilizing bushings for.025" and.045" square. urrent Rating: 7.5 amps maximum for.040" contacts. 13 amps maximum for.062" contacts. S ertified File No. LR34182 Recognized under the omponent Program of Underwriters Laboratories Inc. File No. E31650 RP / 23

24 TX Series TM ORDERING INFORMTION Omit steps not required Heavy Duty, Industrial and ommercial, External Miniture Rectangular Rack & Panel onnectors, Removable ontacts TX 34 S D Step 1 Insert Series ode: TX Step 2 Step 3 No. of Pin or Socket ontacts: ontacts: 9, 14, 18, 20, P - Pin 26, 34, 42, S - Socket and 50 See note 1 below. Step 4 Jackscrews (See bottom chart) Step 5 Shell Type: ** 0 No shell ** 1 Plug shell, style 1 * 000. ** 2 Receptacle shell, style 2 * 000. ** 3 Plug shell, monojack type, style 3 * 000. ** 4 Receptacle, monojack type, style 4 * 000. ** 7 Stainless Steel Plug shell, style 7 * 000. ** 8 Stainless Steel Receptacle shell, style 8 * 000. ** Polarizing Position ** Request availability ** information Step 6 Polarization Position:,,, D, E, F or G. Omit letter when polarization is not required. Step 4 Jackscrews and Jacksockets *** M- Polarized short turnable jackscrew and jacksocket. annot be used with hoods. *** - Polarized long turnable jackscrew and jacksocket for use with hoods. *** D- Polarized one-piece mono-jackscrew and mono-jacksocket (no separate knob); to be used with hoods on sizes: 34, 42, and 50. *** F- Polarized fixed jackscrew and jacksocket usable with or without hood (no knob required). Sizes: 34, 42, and 50. ** MW- Same as M but with knurled round knob with internal hex. ** MU- Same as M but with knurled round knob with screwdriver slot. ** MX- Same as M but with hex knob. ** W- Same as but with knurled round knob with internal hex. ** U- Same as but with knurled round knob with screwdriver slot. ** X- Same as but with hex knob. ** Z- Same as but with prybar knob. Step 7 (See bottom chart) Step 8 Mounting Plate: 00- When no mounting plate is required *10- Mounting plate, style #0010. *Mounting plates are not used with M, or D jackscrews. Step 9 Special Gaskets: Omit letter when gaskets are not required. ** G- ulkhead gasket, style #0000G. Use only when mounting plate is specified. ** F- Face gasket, style #0000F. Use with male insert only. ** - If both gasket #0000G and gasket #0000F are desired. ** heck plant for availability ** on all gaskets. Step 7 Formed Hoods: 0- No Hood. 3- Hood, top opening, style #0300, for use with Type or D jackscrews. 4- Hood, side opening, style #0400, for use with Type or D jackscrews. 5- Hood, top opening, style #0500J, for use with F style jackscrews. 6- Hood, side opening, style #0600J, for use with F style jackscrews. Deep Drawn Hoods: 7- Hood, top opening, style #0700, for use with Type or D jackscrews. 8- Hood, side opening, style #0800, for use with Type or D jackscrews. 9- Hood, top opening, style #0900, for use with F jackscrews. 2- Hood, side opening, style #0200, for use with F jackscrews. Note: ddition of X to code # indicates cable opening larger than std. See hoods for cable opening size. Example: TX20P1300 X *** Request availability information *** Material Nickel plated brass - standard Note: 1. ontacts are ordered separately. See 100 Series contact section of Rack & Panel DIMENSIONS RP / 24 ll dimensions for TX housing are the same as MR housings. ll hoods, shells, hardware, and accesories used on the TX Series are the same as those used on the X Series. See the X Series section for part numbers and dimensions. Note the TX Series maximum number of contacts is 50.

25 MR Series Miniature Rectangular / #16 ontacts /.062" Dia. / 13 mps Receptacle MR 34S-G Plug MR 34P-G Hood The MR Series offers compact, lightweight and self-aligning plugs and receptacles with unusually high current and voltage ratings for their size. Performance tests show them to well exceed military standards. Except for contact size, the MR and MRE Series share the same hoods, hardware and accessories. Right angle, dip solder, pin or socket contacts are available. onsult factory. Dimensions are for reference only and are subject to change. Outline drawings on request. SPEIFITIONS urrent Rating:13 amps Number of contacts: 9, 14, 20, 34, 41, 42, 50, 50-8, 66, 75, 104 Pin ontacts:.062 diameter, gold plated brass Socket ontacts: Phosphor bronze, gold plated Terminations:.070 dia. solder cup is standard. Will accommodate up to #16 WG stranded wire. Pin and Socket contacts available with.030 diameter dip solder terminations. onsult Sales Dept. for lengths available. Electrical Data:Meets high potential performance of MIL Military versions are QPL d to M28748/1 and M28748/2. The minimum dielectric withstanding voltage is one minute electrification 1000 V, sea level. Dielectric: Polarization: Hoods: Gray glass filled diallyl phthalate, per MIL-M-14, SDG-F. Gold plated guides provide polarization. Polarized nickelplated brass and/or passivated stainless steel jackscrews with anodized aluminum knobs are available. nodized aluminum. May be applied to either plug or receptacle. oth top and side opening hoods available. RP / 25

26 MR Series Miniature Rectangular / #16 ontacts /.062" Dia. / 13 mps TERMINTION TYPES Solder up For pin and socket contacts,.070 diameter solder cup is the standard termination for cable and panel mount applications. Wire accommodation: up to #16 WG stranded. Dip Solder For pin and socket contacts,.030 diameter dip solder terminations, straight or right angle for mounting to printed circuit board or for use with flexible cable. GUIDE SOKETS 3 Types of Guide Sockets are vailable Guide Socket ode Letter pplication ctual Size Photo G* The G type socket is the standard guide supplied. It has good physical strength and may be used electrically in a low current circuit or as a contact for ground leads. G Type For General Use Phosphor K* N* The K guide socket is an excellent electrical conductor. Its extra spring-tension provides a high normal force uniformily distributed along the surface of the engaged pilot guide, thus minimizing electrical resistance. The multivolt drop across extreme ends of the engaged pilot and socket guide is 10 mv. at 20 amps. The high physical strength of the N guide socket allows a greater degree of forcible tightening against a mounting surface than is permitted by the other guide sockets. This feature is particularly desirable for mounting connectors which will be subject to severe vibration in service. N guides are not to be used electrically. * For passivated stainless steel add SS suffix K Type For High Electrical onductivity eryllium opper N Type For extra Mechanical Strength rass Standard Guide Pin mates with all types rass PHYSIL DT WEIGHT IN OZ. PLUG REEPTLE NUMER OF ONTTS SPEIL MR-50-8 with 8, 20 amp solder cup contacts and 50, 13 amp solder cup contacts ONTTS URRENT PIN MX. WIRE SOLDER RTING DIMETER SIZE UP DI 8 20 amps.093 #12 WG.106 D amps.062 #16 WG.070 D RP / 26

27 MR Series Miniature Rectangular / #16 ontacts /.062" Dia. / 13 mps Dimensions are for reference only and are subject to change. Outline drawings on request. Drawings and corresponding part numbers show G type guide sockets Dia. Solder up Receptacle MR 9S-G 4-40 UN-2 THD. Slot.038 Wide Plug MR 9P-G Dia Dia. Solder up Dia. Slot.038 Wide Dia. Solder up.150 Slot.038 Wide Receptacle MR 14S-G 4-40 UN-2 THD. Type Plug MR 14P-G UN-2 THD. Type Receptacle MR 20S-G Plug MR 20P-G Dia. Solder up Dia. Solder up Slot.038 Wide Mounting Holes For No. 4 Machine Screws.180 Receptacle MR 34S-G 4-40 UN-2 THD. Type Slot.038 Wide Plug MR 34P-G UN-2 THD. Type Receptacle MR 41S-G Plug MR 41P-G RP / 27

28 MR Series Miniature Rectangular / #16 ontacts /.062" Dia. / 13 mps Dimensions are for reference only and are subject to change. Outline drawings on request. Drawings and corresponding part numbers show G type guide sockets r Dia Dia. Solder up Dia. Solder up Mounting Holes For No. 4 Machine Screws Receptacle MR 42S-G UN-2 THD. Slot.038 Wide Plug MR 42P-G Mounting Holes For No. 4 Machine Screws Receptacle MR 50S-G UN-2 THD. Slot.038 Wide Plug MR 50P-G Dia. Solder up Dia. Solder up Mounting Holes For No. 4 Machine Screws.180 Receptacle MR 50-8S-G 4-40 UN-2 THD. Slot.038 Wide Plug MR 50-8P-G Mounting Holes For No. 4 Machine Screws Receptacle MR 75S-G UN-2 THD. Slot.038 Wide Plug MR 75P-G R.070 Dia. Solder up UN-2 Thd Dia. hole for safety wire Mounting Holes For No. 4 Machine Screws Receptacle MR 66S-G RP / Slot.038 Wide UN-2 THD. Plug MR 66P-G UN-2 THD. Receptacle MR 104S-J Plug MR 104P-JT

29 MR Series Miniature Rectangular / #16 ontacts /.062" Dia. / 13 mps JKSREWS & JKSOKETS Polarized jackscrews give the ease and assurance of threaded positive coupling. The actuating side consists of two turnable screws, one male and one female, each with knurled and slotted knobs. On the mating half are the two fixed screws required to complete the locking action. When mated, the jackscrews may be locked with a safety wire through the hole in the self-locking pin (in the jackscrew shaft). The drawings show the extension of the jackscrew knobs beyond a typical MR connector and beyond the connector-and-hood assembly (center drawings). Dimensions given are constant for all connectors except as noted. Other dimensions applicable to various hood styles are detailed in the chart UN 2 Thread except size 104 which is 6-32 UN for size Mono- Jackscrew Jacksocket Jackscrew 6-32 UN 2 Thread except size 104 which is 8-32 UN2 D.16 Hood Self Locking Pin E Mono- Jacksocket.052 Dia. Safety Wire Hole F onnector with fixed Jackscrews. ode designation: J Mating connector half with turnable Jackscrews-with-Knobs. ode designation: JT Mating connector half with Hood and turnable Long Jackscrews-with Knobs. ode designation: JTH, JTH1 Mating connector half with Hood and turnable Monojacks. ode designation: JTDH, JTDH1 DIMENSIONS Dimensions are for reference only and are subject to change. Outline drawings on request. onnector Size Dimension Dimension Dimen Dimen Dimension E Dimension F H H1 H8 H9 H H1 H8 H9 D H H1 H8 H9 H H1 H8 H9 MR MR MR MR MR MR MR MR MR MR MR New Monojacks ssemble and Disassemble With Remarkable Ease and Speed To free the connector from the hood, simply remove four screws. Monojacks may be used on miniature rectangular connectors with from 34 to 104 contacts, molds have 2 center thru holes and 4 mounting holes. MOLDINGS HVE STRIGHT THRU HOLES MONOJKS RE PTIVTED IN KEYHOLE SLOT OF HOOD S SHOWN OVE. WHEN USING SHELLS, MONOJKS RE PTIVTED IN KEYHOLE OF SHELL ND LERNE HOLES RE PLED IN HOODS. RP / 29

30 MR Series Miniature Rectangular / #16 ontacts /.062" Dia. / 13 mps JKSREWS & JKSOKETS Dimensions are for reference only and are subject to change. Outline drawings on request..19 Dia..22 Dia Dia..078 Int. Hex..25 Hex JTW JTU JTX JTZ.19 Dia..22 Dia Int. Hex 1 JTW JTU Hex 6-32 UN 2 THD. (Typ).80 JTX UN 2 THD. (Typ) JZ DIMENSIONS ll jackscrews and sockets are stainless steel, passivated, except J & JTD which are nickel-plated brass. ll knobs are aluminum, anodized except JTW and JTW which are stainless steel, passivated. Hood Type Size Type JTW Size Type JTU Size Type JTX Size Type JTZ H H1 H8 H9 H H1 H8 H9 H H1 H8 H9 H H1 H8 H9 Dimension Dimension Dimension Dimension RP / 30

31 MR Series Miniature Rectangular / #16 ontacts /.062" Dia. / 13 mps HOODS - DRWN LUMINUM Dimensions are for reference only and are subject to change. Outline drawings on request..08 D Y Style.228 Dia. 2 Holes For 104*.191 Dia. 2 Holes* H G E D G.08 Z Style.08 E (cable opening) DIMENSIONS Top able Opening Side able Opening DIMENSIONS TOP OPENING Wt. atalog Fits D E F G Oz. No. onnector MR 34H x MR 34P MR 34S MR 50-8H D MR 50-8P MR 50-8S MR 66H MR 66P MR 66S MR 104H D MR 104P MR 104S HOODS - FORMED LUMINUM MRE Series hoods for use with MR Series connectors Style Z Y Y Y atalog No. DIMENSIONS SIDE OPENING D E H G MR 34H x MR 50-8H D MR 66H D MR 104H D Wt. Fits Oz. onnector MR 34P MR 34S MR 50-8P MR 50-8S MR 66P MR 66S MR 104P MR 104S Style Z Y Y Y DIMENSIONS Top able Opening Side able Opening H and H-8 able lamps (Top Opening) ode No. able Dimensions Opening Wt. D E F G Oz. Winchester hardware. Use H8 hoods. Electronics Fits onnector MRE 9H* D.3 MR 9 (P or S) MRE 9H MR 9 (P or S) MRE 14H* D.3 MR 14 (P or S) MRE 14H MR 14 (P or S) MRE 20H* D.3 MR 20 (P or S) MRE 20H MR 20 (P or S) MRE 34H D.6 MR 34 (P or S) MRE 34H MR 34 (P or S) MRE 41H MR 41 (P or S) MRE 42H D.7 MR 42 (P or S) MRE 42H MR 42 (P or S) MRE 50H D.8 MR 50 (P or S) MRE 50H MR 50 (P or S) MRE 75H MR 75 (P or S) MRE 75H D 1.0 MR 75 (P or S) * H Hoods for MR 9, 14, and 20 will not accept JT H-1 and H-9 able lamps (Side Opening) ode No. able Dimensions Opening Wt. D E F G Oz. Fits onnector MRE 9H D.3 MR 9 (P or S) MRE 9H MR 9 (P or S) MRE 14H D.3 MR 14 (P or S) MRE 14H MR 14 (P or S) MRE 20H D.3 MR 20 (P or S) MRE 20H MR 20 (P or S) MRE 34H D.6 MR 34 (P or S) MRE 34H MR 34 (P or S) MRE 41H MR 41 (P or S) MRE 42H MR 42 (P or S) MRE 42H MR 42 (P or S) MRE 50H MR 50 (P or S) MRE 50H MR 50 (P or S) MRE 75H MR 75 (P or S) MRE 75H MR 75 (P or S) RP / 31

32 MR Series Miniature Rectangular / #16 ontacts /.062" Dia. / 13 mps HOODS - LOKING Lock Tabs (MRE-V shown) Lever & Pivot ssemblies (MRE-VL shown) Lever & Pilot ssembly MRE-VL MRE-VL2 Lock Tabs (See Note) MRE-V MRE-V2 Used on onnectors MR 9, 14, 20, 34, 41, 42, 66 MR 50,75 Vibration Locks* Vibration locks offer simplicity of design and positive locking in excess of 50G shock impact and 10G vibration acceleration. Mating halves automatically lock when engaged. To unlock, depress the levers. Drilled holes in the levers are provided for safety wiring. Vibration locks are available separately for assembly on connectors now in service. Each code number indicates two units: two levers with two pivots, and two lock tabs. *US Patent Number Note: When panel mounting the lock-tab half of a MR 34, MR 42 or MR 50 and MR 66 connector, flat washers (.033 minimum thickness) should be used on the mounting screws to shim the moulding away from the panel. DIMENSIONS / MOUNTING RKETS ode No. DIMENSIONS D E F G H MRE Dia 3 Holes (No. 4 Mounting Screw) Wt. Oz..4 H E F G MRE Dia 3 Holes (No. 6 Mounting Screw).6 D DIMENSIONS / PRE-SHPED NYLON POTTING FORMS Dimensions are for reference only and are subject to change. Outline drawings on request. Each form matches the back opening contour of its appropriate shell, and stays easily in place during the potting operation. Of negligible weight, it need not be removed from the.11r Panel Opening MR 50 and MR 75 connectors use the standard MRE 50 and MRE 75 mounting brackets connector after potting. ecause of floating contacts, connector halves should always be engaged during the potting operation to preserve contact alignment. Potting Form Fig. Dimensions ode No. MR 9 FM MR 14 FM MR 20 FM MR 26 FM MR 34 FM MR 41 FM MR 42 FM MR 50 FM MR 75 FM Figure 1 Figure 2 Figure 3 RP / 32

33 MR Series Miniature Rectangular / #16 ontacts /.0262" Dia. / 13 mps ORDERING INFORMTION Omit steps not required MR 34 S G H VL Step 1 Step 2 Insert Series ode y adding ML to the series code, connector is supplied with diallyl phthalate type SDG-F and mil plated contacts. Example: MRML Number of ontacts: 9, 14, 20, 34, 41, 42, 50, 50-8, 66, 75, 104 Step 3 ontact Designation: P - Pin S - Socket When ordering molding less hardware to be used with mono-jacks, see Note below. Step 4 Step 5 Type of Guides and ontact: Jackscrew lank = Locks: Standard (See bottom Solder up hart) Straight Dip Solder.030" dia.: D3 =.094" D4 =.125" D5 =.156" For additional lengths in 1/32" increments, contact Winchester s Sales Department. Step 6 Hoods: H - Standard Top Opening* H1 - Standard Side Opening H8 - Large Top Opening H9 - Large Side Opening See Hood Section for vailability *(Note: H Hoods for MR 9, 14 and 20 will not accept JT hardware. Use H8 hoods.) Step 7 Vibration Locks: V - Lock Tab V2 - Lock Tab (Size 50 & 75) VL - Lever & Pivot ss y VL2 - Lever & Pivot ss y (Size 50 & 75) Step 8 ccessories: FM - Potting Forms. annot be Used with Hoods. Request availability information. Step 9 Special Options: onsult Sales Department Step 5 Guides *G Phosphor ronze ylindrical Guides* *K eryllium opper ylindrical Guides *N rass ylindrical Guides* Guides are not recommended for Size 104 P indicates two guide pins or two jackscrews (EX. JTP) S indicates two guide sockets or two jacksockets. (Ex. GS) Jackscrew Locks *** J Polarized Fixed Jackscrew and Jacksocket JT Polarized Short Turning Jackscrew and Jacksocket JT Polarized Long Turning Jackscrew and Jacksocket *** JTD Polarized Long Turning Mono-Jackscrew and Mono-Jacksocket for Sizes 34, 42, 50, 66, 75, and 104 only. **JZ Same as J but with 6-32 mtg. thd. (Std. on 104) **JTW Same as JT but with knurled round knob with internal hex (not avail. 104) **JTU Same as JT but with knurled round knob with screwdriver slot (not avail. 104) **JTX Same as JT but with hex knob (not avail. 104) **JTW Same as JT but with knurled round knob with internal hex (not avail. 104) **JTU Same as JT but with knurled round knob with screwdriver slot (not avail. 104) **JTX Same as JT but with hex knob (not avail. 104) **JTZ Same as JT but with prybar knob (not avail. 104) ** Request availablity information. ***Material: Nickel-plated brass - standard. * For passivated stainless steel add SS suffix. (Example: MR34SGSS) Mounting Note: onnectors MR 9, MR 14, MR 20 and MR41 use guides or fixed jacks for mounting in a hood or on a panel. onnectors MR 34, MR 42, MR 50, MR 66, MR 75 use four #4 machine screws, and MR 104 uses four #6 machine screws for mounting in a hood or on a panel. Guides are not recommended for use with MR 104. Note: When ordering hoods, hardware and connectors separately for use with JTD Monojacks, connectors must be ordered as follows: Pin connector = MR34P8, MR42P8, etc. Socket connector = MR34S8, MR42S8, etc. The number 8 indicates special housing for use with the JTD Monojack hardware (available on sizes 34, 42, 50, 66, 75 and 104). RP / 33

34 MRE Series Miniature Rectangular / #20 ontacts /.040" Dia. / 7.5 mps Receptacle MRE 14S-G Plug MRE 14P-G Hood MRE 14H MRE Series plugs and receptacles are the accepted standard for rectangular-shaped, miniature, internal-type connectors. They embody all of the features expected of true miniaturization: maximum utility of space, extremely lightweight and unusually high working voltage and current ratings. Their long life and trouble-free service continue to make them highly popular for use in aircraft, instrumentation and portable equipment. The MRE and MR series share the same hoods, hardware and accessories. SPEIFITIONS urrent Rating:7.5 amps No. of ontacts: 7, 8, 9, 11, 14, 18, 20, 21, 26, 34, 41, 42, 50, 75, 104 Pin ontacts:.040 dia., gold plated brass Socket ontacts: Phosphor bronze plated gold. Termination Types:.048 dia. solder cup is standard. It will accept up to #20 WG stranded wire. Pin and Socket ontacts available with dip solder terminations,.025 Dia. heck Sales Dept. for lengths available. Electrical Data:Meets high potential performance requirements of MIL Military versions are QPL d to M28748/5 and M28748/6. The dielectric withstanding voltage is one minute at 1200 Dielectric: Polarization: Hoods: volts. rown mineral filled diallyl phthalate. lso available in gray glass filled diallyl phthalate, per MIL-M-14, SDG-F. Gold plated guides provide positive polarization. Polarized nickel-plated brass and/or passivated stainless steel jackscrews with anodized aluminum knobs are available. nodized aluminum. May be applied to either plug or receptacle. oth top and side openings are available. RP / 34

35 MRE Series Miniature Rectangular / #20 ontacts /.040" Dia. / 7.5 mps TERMINTION TYPES GUIDE SOKETS 3 Types of Guide Sockets are vailable Solder up.048 diameter solder cup is the standard termination for cable and panel mounting applications. It will accept up to #20 WG stranded wire. Dip Solder For mounting on printed circuit boards,.025 diameter straight dip solder terminations (for Pin ontacts and Socket ontacts) are available. onsult the Sales Department for available lengths. Guide Socket ode Letter pplication ctual Size Photo G* The G type socket is the standard guide supplied. It has good physical strength and may be used electrically in a low current circuit or as a contact for ground leads. G Type For General Use Phosphor K* N* The K guide socket is an excellent electrical conductor. Its extra spring-tension provides a high normal force uniformily distributed along the surface of the engaged pilot guide, thus minimizing electrical resistance. The multivolt drop across extreme ends of the engaged pilot and socket guide is 10 mv. at 20 amps. The high physical strength of the N guide socket allows a greater degree of forcible tightening against a mounting surface than is permitted by the other guide sockets. This feature is particularly desirable for mounting connectors which will be subject to severe vibration in service. N guides are not to be used electrically. K Type For High Electrical onductivity eryllium opper N Type For extra Mechanical Strength rass Standard Guide Pin mates with all types rass * For passivated stainless steel add SS suffix PHYSIL DT HOW TO ORDER: To obtain K or N guides in place of the standard G type, substitute the desired socket style code letter ( K or N ) for G in both the Plug and Receptacle ode Numbers. (See ode Numbers in table at right. Total No. of ontacts Plug Winchester Electronics ode No. Recept. Winchester Electronics ode No. No. Standard ontacts, 7.5 mps (.048 dia. solder cup for #20 WG) No. Standard ontacts, 10 mps (.052 dia. solder cup for #18 WG) Weight Oz. 7 MRE 7P-G MRE 7S-G 7 none MRE 8P-N MRE 8S-N 8 none MRE 9P-G MRE 9S-G 9 none MRE 11 P-G MRE 11S-G 11 none MRE14P-G MRE 14S-G 14 none MRE 18P-G MRE 18S-G 18 none MRE 20P-G MRE 20S-G 20 none MRE 21P-G MRE 21S-G 21 none.5.5 Total No. of Plug Rec. ontacts Plug Winchester Electronics ode No. Recept. Winchester Electronics ode No. No. Standard ontacts, 7.5 mps (.048 dia. solder cup for #20 WG) No. Standard ontacts, 10 mps (.052 dia. solder cup for #18 WG) Weight Oz. Plug Rec. 26 MRE 26P-G MRE 26S-G 26 none MRE 34P-G MRE 34S-G 34 none MRE 41P-G MRE 41S-G 41 none MRE 42P-G MRE 42S-G 42 none MRE 50P-G MRE 50S-G 50 none MRE 75 P-G MRE 75S-G 75 none MRE 104P-JT MRE 104S-G 104 none RP / 35

36 MRE Series Miniature Rectangular / #20 ontacts /.040" Dia. / 7.5 mps Dimensions are for reference only and are subject to change. Outline drawings on request R Receptacle MRE 7S-G 4-40 N-2 THD. Slot.038 Wide Plug MRE 7P-G R R N-2 THD. Slot.020 Wide Note: For MRE8, "G" guides not available Receptacle MRE 8S-N Plug MRE 8P-N R 4-40 N-2 THD. Slot.038 Wide RP / 36 Receptacle MRE 9S-G Plug MRE 9P-G

37 MRE Series Miniature Rectangular / #20 ontacts /.040" Dia. / 7.5 mps Dimensions are for reference only and are subject to change. Outline drawings on request r R.09R.130 Receptacle MRE 14S-G 4-40 N-2 THD. SLOT 0.38 WIDE Plug MRE 14P-G.13R.130 Receptacle MRE 18S-N 4-40 N-2 THD. SLOT.038 WIDE Plug MRE 18P-N R R.130 Receptacle MRE 20S-N 4-40 N-2 THD. Plug MRE 20P-N SLOT 0.38 WIDE R 4-40 N-2 THD. Receptacle MRE 21S-N SLOT.038 WIDE Plug MRE 21P-N R R R N-2 THD. SLOT 0.38 WIDE MOUNTING HOLES FOR NO.4 MHINE SREWS N-2 THD. SLOT.038 WIDE Receptacle MRE 26S-N Plug MRE 26P-N Receptacle MRE 34S-N Plug MRE 34P-N RP / 37

38 MRE Series Miniature Rectangular / #20 ontacts /.040" Dia. / 7.5 mps Dimensions are for reference only and are subject to change. Outline drawings on request r r R.130 Receptacle MRE 41S-N SLOT 0.38 WIDE 4-40 N-2 THD. Plug MRE 41P-N MOUNTING HOLES FOR NO.4 MHINE SREWS.180 Receptacle MRE 42S-G 4-40 N-2 THD. SLOT 0.38 WIDE Plug MRE 42P-G R R.16R MOUNTING HOLES FOR NO.4 MHINE SREWS.180 Receptacle MRE 75S-N 4-40 N-2 THD. SLOT 0.38 WIDE Plug MRE 75P-N MOUNTING HOLES FOR NO.4 MHINE SREWS.180 Receptacle MRE 50S-N 4-40 N-2 THD. SLOT 0.38 WIDE Plug MRE 50P-N UN 2 THD 6-32 UN 2 THD MOUNTING HOLES FOR NO.4 MHINE SREWS RP / Receptacle MRE 104S-JT 062 DI HOLE FOR SFETY WIRE Plug MRE 104P-J.13R.09R N-2 THD. Receptacle MRE 11S-G SLOT 0.38 WIDE Plug MRE 11P-G

39 MRE Series JKSREWS & JKSOKETS Miniature Rectangular / #20 ontacts /.040" Dia. / 7.5 mps Polarized jackscrews give the ease and assurance of threaded positive coupling. The actuating side consists of two turnable screws, one male and one female, each with knurled and slotted knobs. On the mating half are the two fixed screws required to complete the locking action. When mated, the jackscrews may be locked with a safety wire through the hole in the self-locking pin (in the jackscrew shaft). The drawings show the extension of the jackscrew knobs beyond a typical MR connector and beyond the connector-and-hood assembly (center drawings). Dimensions given are constant for all connectors except as noted. Other dimensions applicable to various hood styles are detailed in the chart N-2 THD. EXEPT SIZE 104 WHIH IS 6-32 N For Size MONO JKSREW JKSOKET 6-32 UN 2 THRED EXEPT SIZE 104 WHIH IS 8-32 UN 2 ND OR OR JKSREW MONO.16 HOOD SELF LOKING PIN JKSOKET 052 DI SFETY WIRE HOLE D E E DIMENSIONS onnector with fixed Jackscrews. ode designation: J Mating connector half with turnable Jackscrews-with-Knobs. ode designation: JT Mating connector half with Hood and turnable Long Jackscrewswith Knobs. ode designation: JTH, JTH1 Mating connector half with Hood and turnable Monojacks. ode designation: JTDH, JTDH1 Dimensions are for reference only and are subject to change. Outline drawings on request. onnector Size Dimension Dimension Dimen Dimen Dimension E Dimension F H H1 H8 H9 H H1 H8 H9 D H H1 H8 H9 H H1 H8 H9 MRE MRE MRE MRE MRE MRE MRE MRE MRE MRE MRE MRE MRE MRE New Monojacks ssemble and Disassemble With Remarkable Ease and Speed To free the connector from the hood simply remove four screws. Monojacks may be used on miniature rectangular connectors with from 34 to 104 contacts. Molds have 2 center thru holes and 4 mounting holes. MOLDINGS HVE STRIGHT THRU HOLES MONOJKS RE PTIVTED IN KEYHOLE SLOT OF HOOD S SHOWN OVE. WHEN USING SHELLS, MONOJKS RE PTIVTED IN KEYHOLE OF SHELL ND LERNE HOLES RE PLED IN HOODS. RP / 39

40 MRE Series Miniature Rectangular / #20 ontacts /.040" Dia. / 7.5 mps JKSREWS & JKSOKETS.19 DI DI..22 DI..078 INT. HEX..25 HEX. JTW JTZ JTX JTU.22 DI..22 DI..078 INT. HEX..36 1" Dimensions are for reference only and are subject to change. Outline drawings on request. JTW JTU HEX UN 2 THD. (TYP.).80 TYP..16 TYP UN 2 THD. (TYP.) DIMENSIONS JTX JZ ll jackscrews and sockets are stainless steel, passivated, except for J & JTD which are nickel-plated brass. ll knobs are aluminum, anodized except JTW and JTW which are stainless steel, passivated. Hood Type Size Type JTW Type JTU Type JTX Type JTZ Size Size Size H H1 H8 H9 H H1 H8 H9 H H1 H8 H9 H H1 H8 H9 Dimension Dimension Dimension Dimension RP / 40

41 MRE Series Miniature Rectangular / #20 ontacts /.040" Dia. / 7.5 mps HOODS - FORMED LUMINUM Dimensions are for reference only and are subject to change. Outline drawings on request. DIMENSIONS Top able Opening ode No. able Dimensions Opening Wt. D E F G Oz. Fits onnector MRE 7H* D.3 MRE 7 (P or S) MRE 7H MRE 7 (P or S) MRE 8H* D.2 MRE 8 (P or S) MRE 8H D.2 MRE 8 (P or S) MRE 9H* D.3 MRE 9 (P or S) MRE 9H MRE 9 (P or S) MRE 14H* D.3 MRE 14 (P or S) MRE 14H MRE 14 (P or S) MRE 18H* D.4 MRE 18 (P or S) MRE 18H MRE 18 (P or S) MRE 20H* D.3 MRE 20 (P or S) MRE 20H MRE 20 (P or S) MRE 21H MRE 21 (P or S) MRE 21H MRE 21 (P or S) MRE 26H MRE 26 (P or S) MRE 26H MRE 26 (P or S) MRE 34H D.6 MRE 34 (P or S) MRE 34H MRE 34 (P or S) MRE 41H MRE 41 (P or S) MRE 42H D.7 MRE 42 (P or S) MRE 42H MRE 42 (P or S) MRE 50H D.8 MRE 50 (P or S) MRE 50H MRE 50 (P or S) MRE 75H MRE 75 (P or S) MRE 75H MRE 75 (P or S) MR104H FOR DIMENSIONS SEE PGE RP/36 * H Hoods for MRE 7, 8, 9, 14, 18 and 20 will not accept JT hardware. Use H8 hoods. Side able Opening ode No. able Dimensions Opening Wt. D E F G Oz. Fits onnector MRE 7H D.3 MRE 7 (P or S) MRE 8H MRE 8 (P or S) MRE 8H MRE 8 (P or S) MRE 9H D.3 MRE 9 (P or S) MRE 9H MRE 9 (P or S) MRE 14H D.3 MRE 14 (P or S) MRE 14H MRE 14 (P or S) MRE 18H D.3 MRE 18 (P or S) MRE 18H MRE 18 (P or S) MRE 20H D.3 MRE 20 (P or S) MRE 20H MRE 20 (P or S) MRE 21H MRE 21 (P or S) MRE 21H MRE 21 (P or S) MRE 26H MRE 26 (P or S) MRE 26H MRE 26 (P or S) MRE 34H D.6 MRE 34 (P or S) MRE 34H MRE 34 (P or S) MRE 41H MRE 41 (P or S) MRE 42H MRE 42 (P or S) MRE 42H MRE 42 (P or S) MRE 50H MRE 50 (P or S) MRE 50H MRE 50 (P or S) MRE 75H MRE 75 (P or S) MRE 75H MRE 75 (P or S) MR104H-9 FOR DIMENSIONS SEE PGE RP/36 RP / 41

42 MRE Series Miniature Rectangular / #20 ontacts /.040" Dia. / 7.5 mps HOODS - LOKING Lock Tabs (MRE-V shown) Lever & Pivot ssemblies (MRE-VL shown) Lever & Pilot ssembly MRE-VL MRE-VL2 Lock Tabs (See Note) MRE-V MRE-V2 Used on onnectors MR 9, 14, 20, 34, 41, 42, 66 MRE 50,75 Vibration Locks* Vibration locks offer simplicity of design and positive locking in excess of 50G shock impact and 10G vibration acceleration. Mating halves automatically lock when engaged. To unlock, depress the levers. Drilled holes in the levers are provided for safety wiring. Vibration locks are available separately for assembly on connectors now in service. Each code number indicates two units: two levers with two pivots, and two lock tabs. *US Patent Number Note: When panel mounting the lock-tab half of a MRE 34, MRE 42 or MRE 50 and MRE 66 connector, flat washers (.033 minimum thickness) should be used on the mounting screws to shim the molding away from the panel. DIMENSIONS / MOUNTING RKETS ode No. DIMENSIONS D E F G H MRE Dia 3 Holes (No. 4 Mounting Screw) Wt. Oz..4 H E F G MRE Dia 3 Holes (No. 6 Mounting Screw).6 D DIMENSIONS / PRE-SHPED NYLON POTTING FORMS Dimensions are for reference only and are subject to change. Outline drawings on request. Each form matches the back opening contour of its appropriate shell, and stays easily in place during the potting operation. Of negligible weight, it need not be removed from.11r Panel Opening MRE 50 and MRE 75 connectors use the standard MRE 50 and MRE 75 mounting brackets the connector after potting. ecause of floating contacts, connector halves should always be engaged during the potting operation to preserve contact alignment. Potting Form Fig. Dimensions ode No. MRE 7 FM MRE 8 FM MRE 9 FM MRE 14 FM MRE 18 FM MRE 20 FM MRE 21 FM MRE 26 FM MRE 34 FM MRE 41 FM MRE 42 FM MRE 50 FM MRE 75 FM Figure 1 Figure 2 Figure 3 RP / 42

43 MRE Series Miniature Rectangular / #20 ontacts /.040" Dia. / 7.5 mps ORDERING INFORMTION Omit steps not required MRE 34 S G H VL Step 1 Step 2 Insert Series Number of ode: ontacts: MRE 7, 8, 9, 11, y adding ML 14, 18, 20, to the series 21, 26, 34, code, connector 41, 42, 50, is supplied with 75, 104 diallyl phthalate type SDG-F and mil plated contacts. Example: MREML Step 3 ontact Designation: P - Pin S - Socket When ordering molding less hardware to be used with mono-jacks, see note below. Step 4 Step 5 Type of Guides and ontact: Jackscrew lank = Locks: Standard (See bottom Solder up hart) Straight Dip Solder.025" dia.: D3 =.094" D4 =.125" D5 =.156" For additional lengths in 1/32" increments, contact Winchester s Sales Department. Step 6 Hoods: H - Standard Top Opening* H1 - Standard Side Opening H8 - Large Top Opening H9 - Large Side Opening *For MRE 7, 8, 9, 14, 18 and 20, JT hardware may not be used with H hoods. Use H8 hoods. Step 7 Vibration Locks: V - Lock Tab V2 - Lock Tab (Size 50 & 75) VL - Lever & Pivot ss y VL2 - Lever & Pivot ss y (Size 50 & 75) Step 8 ccessories: FM - Potting Forms. annot be Used with Hoods. Request availability information. Step 9 Special Options: onsult Sales Department Step 5 Guides *G Phosphor ronze ylindrical Guides* *K eryllium opper ylindrical Guides *N rass ylindrical Guides* Guides are not recommended for Size 104 P indicates two guide pins or two jackscrews (Ex. JTP) S indicates two guide sockets or two jacksockets. (Ex. GS) Jackscrew Locks ***J Polarized Fixed Jackscrew and Jacksocket JT Polarized Short Turning Jackscrew and Jacksocket JT Polarized Long Turning Jackscrew and Jacksocket *** JTD Polarized Long Turning Mono-Jackscrew and Mono-Jacksocket for Sizes 34, 42, 50, 75, and 104 only. **JZ Same as J but with 6-32 mtg. thd. (Not available 5-3, 8) (Std. on 104) **JTW Same as JT but with knurled round knob with internal hex (not avail. 5-3, 8, 104) **JTU Same as JT but with knurled round knob with screwdriver slot (not avail. 5-3, 8, 104) **JTX Same as JT but with hex knob (not avail. 5-3, 8, 104) **JTW Same as JT but with knurled round knob with internal hex (not avail. 5-3, 8, 104) **JTU Same as JT but with knurled round knob with screwdriver slot (not avail. 5-3, 8, 104) **JTX Same as JT but with hex knob (not avail. 5-3, 8, 104) **JTZ Same as JT but with prybar knob. ** Request availablity information. ***Material: Nickel-plated brass - standard Example: MRE34SJTDH8 * For passivated stainless steel add SS suffix (Example: MRE34SGSS) Mounting Note: onnectors MRE 41, MRE 26, and smaller use guides for mounting in a hood or on a panel. onnectors MRE 34, MRE 42, MRE 50, MRE 75, use four #4 machine screws, in addition to guides, for mounting in a hood or on a panel. Note: When ordering hoods, hardware and connectors separately for use with JTD Monojacks, connectors must be ordered as follows: Pin connector = MRE34P8, MRE42P8, etc. Socket connector = MRE34S8, MRE42S8, etc. The number 8 indicates special housing for use with the JTD Monojack hardware (available on sizes 34, 42, 50, 66, 75 and 104). RP / 43

44 XMR & XMRE Series External Miniature Rectangular / #16 ontacts /.062" Dia. 13 mps #20 ontacts /.040" Dia. / 7.5 mps typical Series XMRE Receptacle and Plug fully wired and potted. SPEIFITIONS The XMRE and XMR Series connectors are designed to provide a sturdy, space-saving, lightweight electrical connection. Inserts are housed in protective shells with screw lock coupling plus wall and cable mounting accessories available. urrent Rating:XMR - 13 amps XMRE amps No. of ontacts: XMR - 9, 14, 20, 34, 42, 50, 50-8, 66, 75, 104 XMRE - 9, 14, 18, 20, 26, 34, 42, 50, 75, 104 Pin ontacts: XMR diameter, gold plated brass XMRE diameter, gold plated brass Socket ontacts: Phosphor bronze plated gold. Termination Types: XMR dia. solder cup will accept up to #16 WG stranded wire. XMRE dia. solder cup will accept up to #20 WG stranded wire. Electrical Data: oth XMRE and XMR meet high potential performance requirements of MIL Military versions are QPL d to M28748/1 and M28748/2 (XMR) and to M28748/5 and M28748/6 (XMRE) The minimum dielectric withstanding voltage is one minute electrification at 1000 V (sea level) for XMR and 1200 V for XMRE Series. Dielectric: Polarization: Hoods: rown mineral filled diallyl phthalate. lso available in gray glass filled diallyl phthalate, per MIL-M-14, SDG-F. polarizing stud in the plug shell and a mating slot in the receptacle shell eliminates misalignment. Jackscrews and jacksockets or guide pins and sockets are alternative methods of polarization. nodized luminum. May be applied to both plug and receptacles. oth top and side opening hoods are available. RP / 44

45 XMR & XMRE Series External Miniature Rectangular / #16 ontacts /.062" Dia. 13 mps #20 ontacts /.040" Dia. / 7.5 mps ONNETOR SSEMLIES ONNETOR TERMS Plug: The complete connector half which has the plug shell as part of its assembly. Receptacle: The complete connector half which has the receptacle shell as part of its assembly. Shell: The metal housing in which a male or female insert is assembled. shell is either a plug shell or a receptacle shell. Plug Shell: One which is designed to be inserted into a receptacle shell. Receptacle Shell: One which is designed to receive and enclose the plug shell upon engagement. Male Insert: The molded insulator body containing pin contacts. Femal Insert: The molded insulator body containing socket contacts. Pin ontacts: Male metal conductors that fit into the socket contacts. Socket ontacts: Female metal conductors, tubular in shape, which receive the pin contacts and retain them by spring tension. Polarization: means of controlling the engagement of a plug and receptacle so that correct mating of the contacts is achieved. Potting Form: plastic mold used to retain and shape the sealing compound during the moisture-proofing, or potting operation. Potting: method of moisture-proofing the back of a plug or receptacle and the soldered wire connections by injecting a free flowing sealing compound into a pre-shaped form and allowing it to set. The result is a homogeneous mass, chemically bonded to the back of the insert and around the soldered connections. ccessories: Those components such as hoods, mounting plates and finger grips which are attachable to a plug or receptacle to facilitate mounting and/or handling of the connector. RP / 45

46 XMR & XMRE Series External Miniature Rectangular / #16 ontacts /.062" Dia. 13 mps #20 ontacts /.040" Dia. / 7.5 mps Dimensions are for reference only and are subject to change. Outline drawings on request. ontact rrangements R R R R.09R.13R R ontacts 14 ontacts 18 ontacts 20 ontacts XMRE 9 or XMR9 XMRE 14 or XMR 14 XMRE 18 XMRE 20 0r XMR R R R R R 26 ontacts XMRE Mounting holes for No. 4 machine screws.180 Mounting holes for No. 4 machine screws.180 Mounting holes for No. 4 machine screws.180 Mounting holes for No. 4 machine screws ontacts 50 ontacts 34 ontacts XMR ontacts XMRE 34 XMRE 42 or XMR 42 XMRE 50 or XMR R Mounting holes for No. 4 machine screws RP / Mounting holes for No. 4 machine screws r Mounting holes for No ontacts machine screws 58 ontacts 66 ontacts XMR 104 XMR 50-8 XMR ontacts XMRE 75 or XMR 75 XMRE Views are rear (wiring end) of female inserts (male inserts are mirror image). The spacing, arrangement, and identification of contacts of the XMRE inserts are the same as found on the Series MRE onnectors for the same number of contacts.

47 XMR & XMRE Series External Miniature Rectangular / #16 ontacts /.062" Dia. 13 mps #20 ontacts /.040" Dia. / 7.5 mps JKSREWS & JKSOKETS Jackscrew Locking Devices Polarized jackscrews offer the ease and assurance of threaded positive coupling. They are particularly desirable for the larger connectors (XMRE 34 and larger) whenever they are to be used in locations that make it difficult to apply enough direct pull to separate the two halves of the connector. Type (long-turning jackscrews and jacksockets) or Type D (monojacks) must be specified if both jackscrews and hood are required on the same connector half. Monojacks eliminate the need for roll pins, spacers and washers. Jacksocket.73 Shell Mono- Jackscrew 4-40 UN Except size 104 which is 6-32 Jackscrew 6-32 UN Except 104 Which is 8-32 UN onnector with fixed Jackscrews ode designation: F ND Mating connector half with turnable Jackscrews-with-Knobs ode designation: M Hood Self locking pin OR Mating connector half with Hood and turnable Long Jackscrews-with- Knobs Mono- Jacksocket.052 Dia. safety wire hole ode designation: -0300, OR Mating connector half with Hood and turnable Monojacks ode designation: D-0300, D-0400 Drawings show extension of knobs beyond shell (left) and beyond hood. Refer to details of shells and hoods for the other dimensions which vary according to connector size. DIMENSIONS Dimension SERIES ODE X XMRE X XMR Dimension ODE Part Jackscrews Jacksockets Jackscrews Jacksockets Jackscrews Jacksockets Knobs (except Monojacks Monojackscrews Monojacksockets ode Letter Turntable M Long Turntable Fixed Turning Turning F D Wt. Oz. See Notes 1 & Material and Finish stainless steel with passivating dip stainless steel with passivating dip nickel-plated brass al. anodized nickel-plated brass Note 1: Weights are given for pairs, i.e., for a jackscrew and a jacksocket, etc., so that the weight figure may be added once to the weights of other accessories when computing the total weight of a plug or receptacle. Note 2: Weights of turnable jackscrews and turnable jacksockets include knobs and roll pins; weights of fixed hardware include nuts. Guide Socket ode Letter G K N MTERILS "G" Socket: "K" Socket: "N" Socket: Guide Pin: G Type For General Use ctual Size Photo K Type For High Electrical onductivity Standard Guide Pin mates with all types N Type For Extra Mechanical Strength FINISH Phosphor Gold over Nickel bronze. eryllium copper. rass. rass RP / 47

48 XMR & XMRE Series External Miniature Rectangular / #16 ontacts /.062" Dia. 13 mps #20 ontacts /.040" Dia. / 7.5 mps JKSREW & JKSOKETS Dia..078 Int. Hex.25 Hex. W U X Z Dia..078 Int. Hex Dimensions are for reference only and are subject to change. Outline drawings on request..25 Hex MW MU UN 2 THD. (Typ) DIMENSIONS MX FZ ll jackscrews and sockets are stainless steel, passivated, except F & D which are nickel-plated brass. ll knobs are aluminum, anodized except MW and W which are stainless steel, passivated. RP / 48 Jackscrew Locking For Series XMRE, XMR Size X 0400X Dimension - Type W Size X 0400X Dimension - Type X Size X 0400X Dimension - Type U Size X 0400X Dimension - Type Z

49 Rack & Panel XMR & XMRE Series External Miniature Rectangular / #16 ontacts /.062" Dia. 13 mps #20 ontacts /.040" Dia. / 7.5 mps DIMENSIONS HOODS - DRWN LUMINUM D Top able Opening Hood For use with Type Jacksockets & Jackscrews For use with Type D Jacksockets & Jackscrews For use with G, K, or N, Type Guides or Type F Jackscrews Dimensions are for reference only and are subject to change. Outline drawings on request. Dimensions Part Number D E G XMR x XMR D XMR D XMR D XMR D x XMR D D XMR D D XMR D D XMR x.75 XMR D XMR D XMR D DIMENSIONS HOODS - FORMED LUMINUM Side able Opening Hood For use with Type Jacksockets & Jackscrews For use with Type D Jacksockets & Jackscrews For use with G, K, or N, Type Guides or Type F Jackscrews For use with For use with Type G, K, or N, Type able Jacksockets & Dimensions Guides Opening For use * with Jackscrews Monojacks Hood Part No. E F (If ordered separately) D Dia. Dia. XMRE XMRE X XMRE X XMRE D XMRE X XMRE X XMRE D XMRE X XMRE X XMRE D XMRE X XMRE X XMRE XMRE XMRE X XMRE X XMRE D XMRE XMRE D XMRE XD XMRE X XMRE X XMRE D XMRE XMRE D XMRE XD XMRE X XMRE X XMRE D XMRE XMRE D XMRE XD XMRE X XMRE X XMRE D XMRE XMRE XMRE XD XMRE X XMRE X For use with Monojacks.1935 Dia. 2 Holes (.228 Dia. For XMR Only) Style Y G Style Z For use with Type Jacksockets & Jackscrews E (cable opening) For use with G, K, or N, Type Guides * Dimensions Dimensions Part Number D E H G XMR x XMR D XMR D XMR D XMR D x XMR D D XMR D D XMR D D XMR X XMR D 1.34 XMR D 1.34 XMR D 1.63 able Opening Hood Part No. (If ordered separately) D E Dia. F Dia. XMRE XMRE D XMRE X XMRE X XMRE XMRE D XMRE X XMRE X XMRE XMRE D XMRE X XMRE X XMRE XMRE D XMRE X XMRE X XMRE XMRE XMRE X XMRE X XMRE D XMRE XMRE XMRE XD XMRE X XMRE X XMRE D XMRE XMRE XMRE XD XMRE X XMRE X XMRE D XMRE XMRE XMRE XD XMRE X XMRE X XMRE D XMRE XMRE XMRE XD XMRE X XMRE X * dd J to hood P/N when used with F jackscrews..191 Dia. 2 Holes (.228 Dia. For XMR Only) Side able Opening G H Wt. Oz Wt. Oz Top able Opening D E & F (cable opening) E (cable opening) 0300X & 0500X Style able lamp D F E Drilled for long jackscrews and jacksockets (type ) in Hood style 0300 only E F E & F (cable opening) 0400X & 0600X Style able lamp RP / 49 D

50 XMR & XMRE Series External Miniature Rectangular / #16 ontacts /.062" Dia. 13 mps #20 ontacts /.040" Dia. / 7.5 mps SHELLS - REEPTLE Important Note When Ordering Plug and Receptacle Shells The shell part numbers given in table show an asterisk (*) where the code letter for the desired polarizing position belongs - example: XMRE9-2*000 becomes XMRE when polarization in position is desired. Specify the same position on the mating shell. For non-polarized shells, merely omit this position, e.g. XMRE TYPIL SHELLS FOR MONOJKS Shells are aluminum, anodized for protection against corrosion. Either shell style - plug or receptacle - may be used to house the female insert, thus allowing the live socket contacts to be cable or panel mounted, as desired. Shells also provide a means by which connector polarization is accomplished - the receptacle shell is slotted for engaging a polarizing pin on the plug shell. ny of seven positions (,,, D, E, F, or G) may be specified for polarization; non-polarized shells have the slot and pin omitted. Stainless steel shells available for 66 and 104 sizes. Dimensions vary from those shown for aluminum shells, heck Sales for availability and dimensions on all sizes. For onnector Size 34, 42, 50, 50-8, 66, R R RP / 50 E F G D F.28 Polarizing Slot.156 Typ.312 Typ.06R.03R.06R Mtg Hole Style 9.06R.120 Dia. 2 Holes E D.14R Dimensions are for reference only and are subject to change. Outline drawings on request..14r r G Shell Part No. (if ordered separately).120 Dia. For ll onf. For 9 to 26 For 34, 42, and For 66 and DIMENSIONS SHELLS - REEPTLE E D.06R.384R Dimensions Wt. D E F G Oz. XMRE 9-2* XMRE 14-2* XMRE 18-2* XMRE 20-2* XMRE 26-2* XMRE 34-2*000 XMRE 34-4* XMRE 42-2*000 XMRE 42-4* XMRE 50-2*000 XMRE 50-4* XMR 66-2*000 XMR 66-4*000 XMR *000 XMR * XMRE 75-2*000 XMRE 75-4* XMR 104-2*000 XMR 104-4* Type Dia. 4 orner Holes 2 Slots For 34, 42, 50, 50-8, 66 and 104 onfiguration E D G.120 Dia. 6 Holes Dia. 4 Holes Dia. 4 orner Holes Type 4 Slots.06R.117 For 75 onfiguration.20r E D.120 Dia. 4 Holes.06R G For 75 For 104 Receptacle Shell Style Number R E D.150 Dia. 6 Holes Shells are.040 in. thick.

51 XMR & XMRE Series External Miniature Rectangular / #16 ontacts /.062" Dia. 13 mps #20 ontacts /.040" Dia. / 7.5 mps SHELLS - PLUG Dimensions are for reference only and are subject to change. Outline drawings on request..140 Dia. 4 Holes.06R.03R.120 Dia..14R.06R Mtg. Hole Style 9 F.508 D E.06R D E.06R D E.06R D E.06R D E.06R E F G D.150 Dia. 6 Holes G.875 For R.120 Dia. 4 Holes For 75.20R.120 Dia. 6 Holes G.500 For 66 and R.120 Dia. 6 Holes G.468 For 34, 42, and 50.14R.120 Dia. 2 Holes For 9 to 26 Polarizing Pin For ll onfig. DIMENSIONS Typical Shells For Monojacks For onnector Size 34, 42, 50, 50-8, 66, R R Shell Part No. (if ordered Dimensions Wt. separately) D E F G Oz. XMRE 9-1* XMRE 14-1* XMRE 18-1* XMRE 20-1* XMRE 26-1* XMRE 34-1*000 XMRE 34-3* XMRE 42-1*000 XMRE 42-3* XMRE 50-1*000 XMRE 50-3* XMR 66-1*000 XMR 66-3* XMR *000 XMR *000 XMRE 75-1*000 XMRE 75-3* XMR 104-1*000 XMR 104-3* Type Dia. 4 orner Holes Dia. 4 orner Holes 4 Slots 2 Slots Type For 75 onfiguration For 34, 42, 50, 50-8, 66 and 104 onfiguration Plug Shell Style Number 1000 Shells are.040 in. thick. RP / 51

52 XMR & XMRE Series External Miniature Rectangular / #16 ontacts /.062" Dia. 13 mps #20 ontacts /.040" Dia. / 7.5 mps MOUNTING PLTES Dimensions are for reference only and are subject to change. Outline drawings on request. Mounting Plates for External Miniature Rectangular onnectors, Potting Forms Mounting Plates enable attachment of a connector to a wall, bulkhead, or other supporting surface. The plate is assembled to the back of a plug or receptacle by employing the same hardware and/or guides used to retain the insert in the shell; No. 4 machine screws are then used to mount the complete assembly against the required surface. Mounting plates are aluminum, anodized to resist corrosion..16r.125 Dia. 4 Holes.06R G Mounting plate plan view for 9 to 26 contacts D F E.040 Stock.125 Dia. 10 Holes.125 Dia. 12 Holes.125 Dia. (66 & 50-8).150 Dia. (104) 10 Holes.06R F.23.06R D E F H D E.16R G Panel ut Out.040 Stock H Dimension 50-8 = = =.437 G Panel ut Out DIMENSIONS Left half shows holes for 34, 42, 50 contacts; right half for 75 contacts only. Each plate is symmetrical about the indicated center line. Mounting Plate Plan View for 50-8, 66 & 104 ontacts Note:.19R for 104 and.16r for 50-8 & 66 for panel cutout..050 Stock POTTING FORMS DIMENSIONS RP / 52 Mounting Plate Part No. (If Ordered Separately) Dimensions Wt. D E F G Oz. XMRE XMRE XMRE XMRE XMRE XMRE XMRE XMRE XMRE XMR XMR XMR Potting Forms for External Miniature Rectangular onnectors Nylon Potting Forms: Each form matches the back opening contour of its appropriate shell. Stays easily in place during the potting operation. Of negligible weight, the form need not be removed from the connector after potting. XMRE and XMR connector-halves should always be engaged during the potting operation to preserve the contact alignment. Potting Form Part No. (If Ordered Separately) Dimensions XMRE XMRE XMRE XMRE XMRE XMRE XMRE XMRE XMRE Panel utout Potting Form Part No. (If Ordered Separately) Dimensions XMR XMR * XMR XMR XMR XMR XMR XMR XMR XMR Potting form plan view for 9 to 26 contacts.025 Wall Thick.50 Potting form plan view for 34, 42, 50, 50-8, 66, and 104 contacts *Stepped construction not shown or dimensioned. ut-outs to clear XMR barriers not shown.

53 XMR & XMRE Series External Miniature Rectangular / #16 ontacts /.062" Dia. 13 mps #20 ontacts /.040" Dia. / 7.5 mps ORDERING INFORMTION Omit steps not required XMRE 34 S -F XMR 34 S -F Step 1 Insert ode No. of ontacts: XMR 9, 14, 20, 34, 42, 50, 50-8, 66, 75, 104 XMRE 9, 14, 18, 20, 26, 34, 42, 50, 75, 104 y adding ML to the series code, connector is supplied with diallyl phthalate type SDG-F and mil plated contacts. Example: XMREML XMRML Step 2 Pin or Socket ontacts: P - Pin S - Socket Step 3 Type of ontact: lank = Standard Solder up Straight Dip Solder.030" dia.= XMR.025" dia.= XMRE D3 =.094" D4 =.125" D5 =.156" For additional lengths in 1/32" increments, contact Winchester s Sales Department. Step 4 Guides Jackscrews and Jacksockets (See bottom chart) Step 4 Step 5 Shell Type: 0 No shell. 1 Plug shell, style 1 * Receptacle shell, style 2 * Plug shell, monojack type, style 3 * Receptacle, monojack type, style 4 * 000. ** 7 Stainless Steel Plug shell, style 7 * 000 (66 & 104 only) ** 8 Stainless Steel Receptacle shell, style 8 * 000 (66 & 104 only) * Polarizing Position ** Request availablity information. Step 6 Polarization Position:,,, D, E, F or G. Omit letter when polarization is not required. Guides G- ylindrical guide with single spring member. Recommended for ground only. K- ylindrical guide with four spring members. May be used for electrical contact. N- ylindrical guide without spring member. Recommended for extra mechanical strength. Jackscrews and Jacksockets *** M- Polarized short turnable jackscrew and jacksocket. annot be used with hoods. *** - Polarized long turnable jackscrew and jacksocket for use with hoods. *** D- Polarized turnable jackscrew and jacksocket for use with hoods for sizes 34 thru 104 excluding 41. *** F- Polarized fixed jackscrew and jacksocket. *** J- Non-polarized short turnable jackscrews. annot be used with hoods. *** L- Non-polarized long turnable jackscrews. *** R- Non-polarized fixed jacksocket. *** FZ- Same as F but with 6-32 mtg thd (std on 104). *** MW-Same as M but with knurled round knob with internal hex (not avail. 104). *** MU- Same as M but with knurled round knob with screwdriver slot (not avail. 104). *** MX- Same as M but with hex knob (not avail 104). *** W- Same as but with knurled round knob with internal hex (not avail. 104). *** U- Same as but with knurled round knob with screwdriver slot (not avail. 104). *** X- Same as but with hex knob (not avail. 104). *** Z- Same as but with prybar knob (not avail. 104). *** Request availablity information. *** Material: Nickel-plated brass - standard Step 7 (See bottom chart) Step 7 Step 8 Mounting Plate or Finger Grips: Step 9 Special Gaskets: Omit letter when gaskets 00- When no are not required. mounting ** G- ulkhead gasket, style plate is #0000G. Use only required when mounting plate is *10- Mounting specified. plate, style ** F- Face gasket, style #0010. #0000F. Use with *Mounting plates male insert only. are not used with ** - If both gasket #0000G M,, D, J, and gasket #0000F or L jackscrews. are desired. ** heck plant for availability ** on all gaskets. Potting Form or Hoods: 0- When no potting form or hood is required. 1- Potting form style #0100. annot be used with hood. Request availability information. annot be used Formed Hoods: 3- Hood, top opening, style #0300, for use with Type or D jackscrews. 4- Hood, side opening, style #0400, for use with Type or D jackscrews. 5- Hood, top opening, style #0500, for use with G, K, or N type guides only and F style jackscrews. 6- Hood, side opening, style #0600, for use with G, K, or N type guides only and F style jackscrews. Deep Drawn Hoods: 7- Hood, top opening, style #0700, for use with Type or D jackscrews. 8- Hood, side opening, style #0800, for use with Type or D jackscrews. 9- Hood, top opening, style #0900, for use with G, K, and N type guides or F jackscrews. 2- Hood, side opening, style #0200, for use with G, K, or N type guides or F jackscrews. Note: ddition of X to end of code # indicates cable opening larger than std. See hoods for cable opening size. Example: XMRE34PD3300X RP / 53

54 SLE-SME-SRE Series Sub Miniature / High Density Rectangular /.025" Dia. / 3 mps.030" Dia. / 5 mps /.040" Dia. / 7.5 mps SLE.025 Diameter ontacts 3 mps. SRE.030 Diameter ontacts 5 mps SME.040 Diameter ontacts 7.5 mps Within this series, you ll find a standard size connector for which you can select one of three current ratings: 3, 5 or 7.5 amps. ompact and lightweight, they are especially suited for aircraft, instrumentation and portable equipment applications. Right angle, dip solder, pin or socket contacts are available. onsult factory. SPEIFITIONS urrent Rating:SLE - 3 amps: SRE - 5 amps; SME amps. No. of ontacts: 4, 5, 7, 9, 11, 14, 20, 26, 29, 34, 44, 50. Pin ontacts: rass, gold plated except for SLE which is phosphor bronze, gold plated. Socket ontacts: Termination Types: Phosphor bronze, gold plated..037 diameter solder cup will accept up to #22 WG stranded wire. Solder cup adaptor (Part No. S45) will accept up to #20 WG stranded wire. Dip solder terminations available for SRE Series,.030 Dia. heck Sales Department for available lengths. Military versions of SRE are QPL d to M28748/7 and M28748/8. Electrical Data:The dielectric withstanding voltage is one minute Dielectric: Guides: Jackscrews: Hoods: electrification at 1000 V. Green glass-filled diallyl phthalate per MIL-M-14, SDG-F. Type NSS stainless steel, passivated or Type N rass, gold plated. Stainless steel, passivated. luminum knobs on the jackscrews are equipped with set screws, except JTU jackscrews which have stainless steel knobs equipped with groove pins. nodized aluminum. May be applied to either plug or receptacle. oth top and side openings are available for use with either guides or jackscrews. RP / 54

55 SLE-SME-SRE Series ONTT RRNGEMENT Sub Miniature / High Density Rectangular /.025" Dia. / 3 mps.030" Dia. / 5 mps /.040" Dia. / 7.5 mps Mating Face of Female Moldings - Male Moldings Reverse Image Dimensions are for reference only and are subject to change. Outline drawings on request. RP / 55

56 SLE-SME-SRE Series Sub Miniature / High Density Rectangular /.025" Dia. / 3 mps.030" Dia. / 5 mps /.040" Dia. / 7.5 mps Dimensions are for reference only and are subject to change. Outline drawings on request. F D J F E Dia. K Dia Dia. Solder up N Dia UN-2 THD..24 G Slot.031 Wide H Slot.020 Wide M Except Size 44 & 50 Which is 2.34 L THD. N Dia..16 N Dia..16 N Dia Dia. Solder up L THD..032 Dia. Hole L THD. L THD. M 2-56 UN M J Jackscrews JT Jackscrews JTU Jackscrews JT Jackscrews M DIMENSIONS The stainless steel guide pin and socket have good physical strength and are particularly desirable for mounting connectors which will be subject to severe vibration in service, but not for electrical applications. Optional gold plated brass available for electrical applications. No. of ontacts Series D E Dia F G H J K L Thd M N SLE UN* SRE UN* SME UN* *2-56 UN Thread also available. See ordering information for part number suffix. RP / 56

57 SLE-SME-SRE Series Hoods Formed luminum Sub Miniature / High Density Rectangular /.025" Dia. / 3 mps.030" Dia. / 5 mps /.040" Dia. / 7.5 mps Dimensions are for reference only and are subject to change. Outline drawings on request. H E x F able Opening F D G D E.22 Style H9 Side able Opening H.22 Style H8 / H13 Top able Opening DIMENSIONS ORDERING INFORMTION Hood Style Hood atalog Number Dimensions able Opening No. of onacts Guides Only* D G H E F H8 SRE11H H8 SRE50H H9 SRE11H H9 SRE50H H13 SRE4&7H & 7 H13 SRE14H H13 SRE20H H13 SRE26H H13 SRE34H NOT VILLE 9 H13 SRE29H NOT VILLE 44 * dd J to hood part number when used with fixed jackscrews dd JT to hood part number when used with long turning jackscrews. SRE 34 S JT H13 Step 1 Insert ode Series: SLE-.025 Dia. ontact SME-.040 Dia. ontact SRE-.030 Dia. ontact Step 2 Number of ontacts: 4, 5, 7, 9, 11, 14, 20, 26, 29, 34, 44, 50 Step 3 Step 4 ontact Special ontacts: Designation: This step to be used P- Pin only when a special S- Socket material, finish, or style is required. Omit when standard contacts are used. onsult sales department for proper designation. Order Solder up dapter for #20 WG Stranded wire. Use Part No. S45. Must be ordered separately. Step 5 Step 6 Jackscrew Locks: J- Polarized Fixed Screw & Socket JT- Polarized Short Turning Screw & Socket JT- Polarized Long Turning Screw & Socket JTU- Polarized Short Turning Screw & Socket with Round Knob Guides: NSS-Stainless Steel ylindrical Polarized Guides N- Gold Plated rass Polarized Guides Mounting: H8- Large Top Opening H13- Large Top Opening (High) H9- Large Side Opening *When ordering hoods separately use atalog Number in hart Step 7 For Special 2-56 thds add -859 suffix on Series SRE part numbers RP / 57

58 SRE Series Sub Miniature Rectangular, Removable ontacts SRE 14SN SRE 14PNH13 Tool The SRE series is the first family of subminiature crimp contact rack and panel connectors. While retaining all of the important features of true connector miniaturization, the SRE offers.030 diameter crimp (4 indents) type removable contacts with.094 center to center spacing. ontacts are precision machined to assure solid pin and socket reliability. ompact and light in weight, the SRE Series is especially suitable for aircraft, instrumentation, computer and portable equipment applications. SPEIFITIONS urrent Rating: 5 amps No. of ontacts: 7, 11, 14, 18, 20, 26, 34, 44, 50 Pin ontacts:.030 dia. 4 indent crimp. Leaded commercial bronze, gold plated. Socket ontacts: Termination Types: Dielectric: Phosphor bronze, gold plated. rimp or.025 sq. wire wrap. rimp contacts will accommodate #20- #28 WG stranded wire. Glass-filled diallyl phthalate per MIL-M-14, SDG-F. Electrical Data: The dielectric withstanding voltage is one minute electrification at 1400 V. Jackscrews: Long and short turning, passivated stainless steel. nodized aluminum knurled knobs equipped with set screws for long turning jackscrews. Stainless steel knobs with groove pins for short turning jackscrews. Guides: Hoods: Type N is standard - brass for extra mechanical strength. Type K - beryllium copper for high electrical conductivity. Type NSS - stainless steel Top opening hoods are available in all sizes. Side opening available for SRE 50 only. RP / 58

59 SRE Series Sub Miniature Rectangular, Removable ontacts Dimensions are for reference only and are subject to change. Outline drawings on request UN.58 2 THD G H.032 Dia. Hole UN 2 THD. SRE-SJ SRE-PJT SRE-JTH H UN 2 THD..61 SRE-SN/K.23 Slot.031 Wide Slot.020 Wide.44 SRE-PN/K DIMENSIONS PHYSIL DT ONTTS DIMENSION HRT No. of ontacts G H SRE 11, 18 and 44 outline drawings on request Weight in Ounces (w/o contacts) SRE 7 SRE 14 SRE 20 SRE 26 SRE 34 SRE 50 Plug Plug omponent Parts Guide Pin Guide Socket L Washer (2) Nut (2) Weight in Ounces ontact Wire Size Dimensions urrent Part No. Type (Stranded) D Rating P P (Male) S S (Female) mp P P (Male) S S (Female) Polarizing Pin: rass, Gold Plated, Part No RP / 59

60 SRE Series Sub Miniature Rectangular, Removable ontacts FORMED LUMINUM HOODS Dimensions are for reference only and are subject to change. Outline drawings on request. H F E able Opening D E D H DIMENSIONS SRE/ SRE Large Top Opening Hoods ode No.* Dimensions able Opening D E F H SRE7H SRE14H SRE20H SRE26H SRE34H SRE50H ORDERING INFORMTION Fits onnector SRE 7 P/ S SRE 7 P/S SRE 14 P/S SRE 14 P/S SRE 20 P/S SRE 20 P/S SRE 26 P/S SRE 26 P/S SRE 34 P/S SRE 34 P/S SRE 50 P/S SRE 50 P/S SRE/ SRE Large Side Opening Hoods ode Fits No.* D E H onnector SRE50H x SRE 50 P/S SRE 50 P/S * ode numbers shown are for use with guides. For use with jackscrews, add J or JT to hood part number. Omit steps not required SRE 34 S JT H Step 1 Insert Series ode: SRE RP / 60 Step 2 Number of ontacts: 7, 11, 14, 18, 20, 26, 34, 44, 50 Step 3 ontact Designation: P - Pin Molding S - Socket Molding Step 4 ontact Wire Size. Omit this step if contacts are to be ordered separately. Use only when contacts are supplied with connector dd: 20 - for WG 24 - for WG 28 - for WG Step 5 (See bottom chart) Step 5 Guides K- eryllium opper ylindrical Guides Step 6 Step 7 Hood Type: For 2-56 UN H8 - Large Top 2 Threads on Opening Jackscrews, add (50 size only) suffix Omit if not required. H9 - Large Side Opening (50 size only) H13 -Higher Top Opening (all others) See Hood Section For vailability N- rass ylindrical Guides (Standard) NSS- Same style as above but Stainless Steel Jackscrew Locks J- Polarized Fixed Jackscrew and Jacksocket JT- Polarized Short Turning Jackscrew and Jacksocket JT- Polarized Long Turning Jackscrew and Jacksocket

61 42 Series Panel Mount Miniature 22 WG -.030" Diameter - 5 mps TERMINTION TYPES POLRIZTION Dip Solder: Grid Spacing:.125" or.156" standard lengths with other lengths available on special order..100" x.100" grid 50 or 74 contact positions on.100" centers in 3 rows. Two outboard rows for 25 contacts each. enter row either for 24 additional contacts or polarizing pins in specified positions. Solder up: ccommodates up to #22 WG stranded wire. rimp Removable: rimp contacts available for #20 through #30 WG stranded wire. Designed for four indent crimp. See crimp tooling. SPEIFITIONS RIMP TOOLING vailable in 50 contact configuration only. hoice of any combination of 24, center positions. Specify polarizing positions required. Positions top to bottom are:,,, urrent Rating: 5.0 amps. Pin ontacts:.030" dia. gold plated brass conforming to specification QQ Socket ontacts: Gold plated phosphor bronze. Termination Types: Solder cup, dip solder and crimp removable contacts. Housing Material: Red diallyl phthalate for Dip Solder and Solder up Housings. Green diallyl phthalate for rimp Removable Housings utomatic rimping Machine: at. No Hand rimping Tool: at. No Locator: at. No D, E, F, H, J, K, L, M, N, P, R, S, T, U, V, W, X, Y, Z, a.b. When 74 contacts are required no polarization other than hardware polarization is available. Dielectric: Polarization: Jackscrews: Hoods: ontact Removal Tool: at. No ontact Insertion Tool: at. No Minimum withstanding voltage is one minute electrification at 1200 V. Polarizing pins may be used in any combination in center row. Passivated stainless steel, anodized aluminum knobs. nodized aluminum, top opening only. RP / 61

62 42 Series Panel Mount Miniature 22 WG -.030" Diameter - 5 mps Dimensions are for reference only and are subject to change. Outline drawings on request R () 6-32 UN 2- THD Solder up.035 Dia..38 x 1.41 able Opening 4-40 UN 2- THD. Typ.030 Dia ORDERING INFORMTION Solder up, lipped-in ontacts /74 P/S Step 1 Series ode: Series 42 Step 2 Hardware and ccessories: (See bottom chart) Step 3 No. of ontacts: 50 or 74 SOLDER UP PLUG (lipped-in ontacts) 34 = Molding, No Hardware 35 = Molding, With Guides 36 = Molding, With Fixed Jackscrews 52 = Molding, With Short-Turning Jackscrews 53 = Molding, With Long-Turning Jackscrews 54 = Molding, With Guides and Hood 55 = Molding, With Long-Turning Jackscrews 55 = and Hood Step 4 ontact Type: S = Socket P = Pin Step 5 Polarization Positions: lank = Non-Polarized Polarization available in 50 contact configuration only. hoice of any combination of 24 center positions. Specify polarizing positions required. Positions top to bottom are:,,, D, E, F, H, J, K, L, M, N, P, R, S, T, U, V, W, X, Y, Z, a, b. When 74 contacts are required no polarization other than hardware polarization is available. RP / 62 SOLDER UP REEPTLE (lipped-in ontacts) 40 = Molding, No Hardware 41 = Molding, With Guides 42 = Molding, With Short-Turning Jackscrews, 42 = No Hood 43 = Molding, With Long-Turning Jackscrews, 42 = No Hood 44 = Molding, With Guides and Hoods 45 = Molding, With Long-Turning Jackscrews 42 = and Hood 46 = Molding, With Fixed Jackscrews

63 42 Series Panel Mount Miniature 22 WG -.030" Diameter - 5 mps Dimensions are for reference only and are subject to change. Outline drawings on request. Dip Solder Receptacle Shown: 74 contact right angle configuration. enter row eliminated for 50 contact connector UN 2- THD. Typ Dip Solder, Molded-in ontacts ORDERING INFORMTION P 4 Step 1 Step 2 Step 3 Step 4 Step 5 Step 6 Series ode: Series 42 Hardware and ccessories: DIP SOLDER (Molded-in ontacts) 30 = No Hardware 31 = Guide Pin and Socket 32 = Fixed Jackscrew and Jacksocket No. of ontacts: 50 or 74 ontact Type: P = Pin Polarization Positions: lank = Non-Polarized Polarization available in 50 contact configuration only. hoice of any combination of 24 center positions. Specify polarizing positions required. Positions top to bottom are:,,, D, E, F, H, J, K, L, M, N, P, R, S, T, U, V, W, X, Y, Z, a, b. When 74 contacts are required no polarization other than hardware polarization is available. Termination Type: 4 = Dip Solder ontacts...125" 5 = Dip Solder ontacts...156" 852 = Right ngle Dip Solder ontacts.205" RP / 63

64 42 Series Panel Mount Miniature 22 WG -.030" Diameter - 5 amps #6-32 UN #6-32 UN ORDERING INFORMTION P Step 1 Series ode: Series 42 Step 2 1 = rimp onnector Molding Step 3 Hardware and ccessories: (See bottom chart) Step 4 No. of ontacts: 50 or 74 rimp Removable Pin ontacts 34 = Molding, No Hardware 35 = Molding, With Guides 36 = Molding, With Fixed Jackscrews 52 = Molding, With Short-Turning Jackscrews 53 = Molding, With Long-Turning Jackscrews 54 = Molding, With Guides and Hood 55 = Molding, With Long-Turning Jackscrews 55 = and Hood rimp Removable Socket ontacts 40 = Molding, No Hardware 41 = Molding, With Guides 42 = Molding, With Short-Turning Jackscrews, 42 = No Hood 43 = Molding, With Long-Turning Jackscrews, 42 = No Hood 44 = Molding, With Guides and Hoods 45 = Molding, With Long-Turning Jackscrews 42 = and Hood 46 = Molding, With Fixed Jackscrews Step 5 ontact Type: S = Socket P = Pin rimp removable contacts are ordered separately. Pin ontacts: P P P Socket ontacts: S S S Socket ontacts (losed Entry): S S S See 100 Series ontact Section of Rack & Panel Step 6 Polarization Positions: lank = Non-Polarized Polarization available in 50 contact configuration only. hoice of any combination of 24 center positions. Specify polarizing positions required. Positions top to bottom are:,,, D, E, F, H, J, K, L, M, N, P, R, S, T, U, V, W, X, Y, Z, a, b. When 74 contacts are required no polarization other than hardware polarization is available. RP / 64

65 SRM Series Sub Miniature Rectangular #20 ontacts /.040" Dia. / 7.5 mps SRM Series connectors are particularly suitable where current rating and voltage drop requirements dictate a larger wire size than can be used with other subminiature connectors. XSRM14PNSS2500 XSRM14PNSS1000 SRM14SNSS0000 SRM26SO300 XSRM26SM2000 SRM26PF0000 SPEIFITIONS urrent Rating: 7.5 mps No. of ontacts: 5, 7, 11, 14, 20, 26, 34, 50, 75, 104 Pin ontacts:.040 dia. brass, gold plated. Socket ontacts: Termination Types: Phosphor, bronze, gold plated..048 dia. solder cups will accept up to #20 WG stranded wire. Dip Solder ontacts,.030 dia. heck Sales Dept. for available lengths. Electrical Data: Minimum dielectric withstanding voltage is one minute at 1500 V when tested in accordance with MIL Dielectric: Glass-filled diallyl phthalate - grey- per MIL-M-14, SDG-F. Guides: NSS Type, stainless steel; or N Type, brass. Jackscrews: Stainless steel with knurled and slotted aluminum knobs. Hoods: nodized aluminum. May be applied to either plug or receptacle. oth top and side openings are available. Shells: Polarized shells are available. SRM connector assembled with a shell changes part number from SRM _ to XSRM. RP / 65

66 SRM Series Sub Miniature Rectangular #20 ontacts /.040" Dia. / 7.5 mps ONTT RRNGEMENTS Dimensions are for reference only and are subject to change. Outline drawings on request r 2-56 UN - 2 THD R R DI..133 SLOT.025 WIDE Dia. Solder up SRM5P-NSS SRM7S-NSS SRM7P-NSS SRM11P-NSS R R R.34.09R R Mounting holes for.343 No. 2 machine screws () SRM14P-NSS SRM20P-NSS SRM26S-NSS SRM34P-NSS SRM50P-NSS 2-56 UN. 2 THD DI Dia. Solder up r UN THD R.040 Dia Dia. Solder up RP / 66 SLOT.025 WIDE UN. Mounting holes THD. for No. 2 machine screws () *enter guides are.038 x.062 SRM75S-NSS SRM75P-NSS SRM104S-NSS SRM104P-NSS SLOT.025 WIDE.159

67 SRM Series Sub Miniature Rectangular #20 ontacts /.040" Dia. / 7.5 mps JKSREWS & JKSOKETS Dimensions are for reference only and are subject to change. Outline drawings on request. Jacksocket Solder ups Jacksocket F Mating thread size 2-56 UN except size 104 which is 6-32 UN. onnector with fixed Jackscrews ode designation F ESolder ups ND Mating connector half with turnable Jackscrews-with-Knobs ode designation M.11 Hood Set Screw OR Mating connector half with Hood and turnable Long Jackscrews-with-Knobs ode designation -0300, DIMENSIONS ODES Note: Jackscrews and jacksockets are stainless steel with passivating dip. Knob is anodized aluminum. Jackscrew locking device assures positive coupling of engaged connectors to prevent accidental disconnecting from vibration or physical shock. It also aids easy connection and separation of connector plug and receptacle. Mounted connector-half houses one non-turnable fixed jackscrew and jacksocket to insure connector polarization. Mating-half houses one of the two types of turning jackscrew and jacksocket (M or ) Turnable jackscrew-jacksocket combination (M or ) assembles on either Plug or Standard onnector Size Long Turning Short Fixed ode Turning Jacks X ode M ode F E F SRM SRM SRM SRM SRM SRM SRM SRM SRM SRM TYPE ode Letter Jackscrew Jacksocket Fixed F Jackscrew Short Jacksocket Turnable M Jackscrew Long Jacksocket Turnable Knob Standard Receptacle, the mating connector-half (either Receptacle or Plug) must then contain fixed jackscrew-jacksocket combination (F). oth short and long turning jackscrews (M and ) have knurled and slotted knobs for locking by hand or screwdriver. Knob is assembled on shaft with a socket setscrew. Safety wiring of engaged halves is achieved by using the through-holes. Drawings show extension of standard knobs beyond hood. RP / 67

68 SRM Series Sub Miniature Rectangular #20 ontacts /.040" Dia. / 7.5 mps HOODS - FORMED LUMINUM Dimensions are for reference only and are subject to change. Outline drawings on request. Top able Opening Hoods D F Side able Opening Hoods G E F & G (able Opening) (0300 Only) F & G (able Opening) G (0400 Only) D F DIMENSIONS Top able Opening Hoods 2-26 UN-2 THD. (0500 Only) 0300X able lamp 0300X Hood is identical to 0300 Hood except for cable clamp style and cable opening in the hood. ode able No. Dimensions Opening * D E F G SRM X SRM SRM X SRM X SRM SRM X SRM X SRM SRM X SRM X SRM SRM X SRM SRM X SRM SRM X X able lamp 0400X Hood is identical to 0400 Hood except for cable clamp style and cable opening in the hood. ode No. able Dimensions Opening * D E F G Hoods may be ordered separately (see code numbers in above tables) or assembled on connectors. If desired assembled to connectors, see ode Numbering System for complete catalog number. Prefix hood code numbers with X for use with shells. Example: XSRM E 2-56 UN-2 THD. (0600 Only) SRM SRM X SRM SRM X SRM SRM X SRM SRM X SRM Dia. SRM X SRM Dia. SRM X SRM SRM X** SRM SRM X** Side able Opening Hoods RP / 68 ode able No. Dimensions Opening * D E F G SRM SRM X SRM SRM X SRM SRM X SRM SRM X SRM SRM X** SRM SRM X** SRM SRM X SRM SRM X ode No. * * Note: This dimension does not apply when shells are used. Tab is removed. **Request availability information. able Dimensions Opening * D E F G SRM SRM X SRM SRM X SRM SRM X SRM SRM X SRM Dia. SRM X SRM Dia. SRM X SRM SRM X SRM SRM X

69 SRM Series Sub Miniature Rectangular #20 ontacts /.040" Dia. / 7.5 mps PLUG SHELLS Dimensions are for reference only and are subject to change. Outline drawings on request. For Use With XSRM onnectors.05r () Dia. 4 Holes.14R F H D E REEPTLE SHELLS D E.14R.06R.05R 2 Slots For XSMR 7 to Typ D E F G Polarizing Slot For ll XSRM onfig. D E.06R.05R G (.07R for 104) 2 Slots For XSRM 34, 50, and R.093 Dia. 4 Holes.203 G For XSRM 75.14R Dimensions are for reference only and are subject to change. Outline drawings on request. For Use With XSRM onnectors Dia. 4 Holes.14R.093 Dia. 4 Holes F H D E.06R D E D E F G.125 Typ.06R D E.06R MTERIL.14R.05R 2 Slots For XSMR 7 to 26 Polarizing Slot For ll XSRM onfig. G.05R (.07R for 104) 2 Slots For XSRM 34, 50, and R G.203 For XSRM 75.05R () POLRIZTION Shells are.031 thick aluminum, anodized for protection against corrosion. Either style - plug or receptacle - may be used to house a female insert, thus allowing live socket contacts to be cable or panel mounted. Shells also provide a means by which connector polarization is accomplished - receptacle shell is slotted for engaging a polarizing pin on plug shell. Non-polarized shells have the slot and pin omitted. DIMENSIONS The shell part numbers given in table show an asterisk (*) where the code letter for the desired polarizing position belongs - example: XSRM14-2*000 becomes XSRM Shell Size vailable Polarization Shell Size Positions 7,,,D 11,,,D 14,,,D,E 20,,,D,E,F,G 26,,,D,E,F,G when polarization in position is desired. Specify the same position on the mating shell. For non-polarized shells, merely omit this position, e.g. XSRM vailable Polarization Positions 34,,,D,E,F,G 50,,,D,E,F,G 75,,,D,E,F,G 104,,,D,E,F,G Plug Shells (.031" thick) Shell Part No. (if ordered separately) Winchester Electronics Dimensions D E F G H XSRM 7-1* XSRM 11-1* XSRM 14-1* XSRM 20-1* XSRM 26-1* XSRM 34-1* XSRM 50-1* XSRM 75-1* XSRM 104-1* Receptacle Shells (.031" thick) Shell Part No. (if ordered separately) Dimensions D E F G H XSRM 7-2* XSRM 11-2* XSRM 14-2* XSRM 20-2* XSRM 26-2* XSRM 34-2* XSRM 50-2* XSRM 75-2* XSRM 104-2* RP / 69

70 SRM Series Sub Miniature Rectangular #20 ontacts /.040" Dia. / 7.5 mps ORDERING INFORMTION Omit steps not required SRM 26 P Step 1 Step 2 Insert Series Number of ode: ontacts: SRM - When 5, 7, 11, protective 14, 20, 26, shells are not 34, 50, 75 required. and 104. XSRM - When protective shells are required. Step 3 ontact Designation: P - Pin S - Socket Step 4 Step 5 Type of Guides: ontact: (See bottom lank = hart) Standard Solder up This step to be used only when a special material, finish, or style is required. Omit when standard contacts are used. onsult Sales Department for proper designation of Dip Solder Terminations Step 6 Shell Type: 0 -Shell not required SRM Series 1 -Plug shell XSRM Series 2 -Receptacle shell XSRM Series Step 7 Polarization Position:,,, D, E, F or G. Omit letter when polarization of shell is not required. Step 5 Guides NSS - Standard stainless steel cylindrical guides. N - rass cylindrical guides. Plated, gold over copper. Jackscrews and Jacksockets - Polarized long turning jackscrew and jacksocket for use with hoods. F - Polarized fixed jackscrew and jacksocket. M - Polarized short turning jackscrew and jacksocket. J - Non-polarized short turning jackscrews. L - Non-polarized long turning jackscrews. R - Non-polarized fixed jacksockets. Step 8 Hoods: 0 -When no hood required. 3 -Standard size top cable opening. If extra large cable opening is desired, add X to end of catalog number. 4 -Standard size side cable opening. If extra large cable opening is desired, add X to end of catalog number. 5 -Top opening hood for use with guides. 6 -Side opening hood for use with guides. Step 9 0 fill to complete part number Step 10 0 fill to complete part number RP / 70

71 PM1 Series High Voltage, Single ontact / # 20 ontacts /.040" Dia. / 7.5 mps N Nylon Nut PM1SLR Plug with lock ring PM1PLS Receptacle with lock spring H10 Hood Dimensions are for reference only and are subject to change. Outline drawings on request O This connector was developed for applications requiring moderately high voltage ratings, this single contact connector is particularly well adapted to Photo-Flash, ircraft, Instumentation and ommunications Equipment Hex able Opening.16 Panel Drilling.048 Dia. Solder up 3/8-24 UNF - 2THD. PM1SLRN Plug with lock ring PM1PLS Receptacle with lock spring H10 Hood SPEIFITIONS ORDERING INFORMTION urrent Rating: 7.5 amps No. of ontacts: 1 Pin ontacts:.040 dia. brass, gold plated Socket ontacts: Phosphor bronze, gold plated Terminations:.048 solder cup will accept up to # 20 WG stranded wire. Electrical Data: Dielectric withstanding voltage is one minute electrification at 5650 V. Dielectric: Molded Diallyl phthalate per MIL-M-14, type SDG-F. olor Gray. Polarization: Permits one engaging position only and prevents rotation of the plug and PM1PLR- onnector, plug with lock ring PM1SLS- onnector, receptacle with lock spring PM1PLS- onnector, plug with lock spring PM1SLR- onnector, receptacle with lock ring PM1P- onnector, plug without vibration lock PM1S- onnector, receptacle without vibration lock * dd H10- to above numbers when ordering hoods * dd H10- to above numbers for hood with cable clamp dd N- to above numbers when ordering nylon nut receptacle with respect to each other. Mounting: able or panel mounted. Use nylon nut applied to either plug or receptacle. Lock Ring (and lock spring): pplied to plug or receptacle. Prevents connector rotation on panel and when engaged with lock spring, prevents accidental disconnection due to vibration, etc. Hood: Diallyl Phthalate cable hood Weight in Ounces: Receptacle.05, Plug.05, Washer.005, Hood.07, Lock Ring.017, Lock Spring.019, Nut.015 * When ordering hoods separately specify P/N H10T34 or H10T34 RP / 71

72 PM6 Series High Voltage Miniature / # 20 ontacts /.040" Dia. / 7.5 mps N Nylon Nut PM6SLR Receptacle with lock ring PM6PLS Plug with lock spring PM6H Hood This connector was developed for applications requiring moderately high voltage ratings, this connector of minimum bulk and weight is particularly well adapted to Photo- Flash, ircraft, Instumentation and ommunications Equipment. Dimensions are for reference only and are subject to change. Outline drawings on request Dia O.875 Dia Molding Nut.048 Dia. Solder up Hex.22 7/8 20 UNEF Dia. able Opening.78 Dia. Panel Drilling PM6SLRN Receptacle PM6PLS Plug PM6H Hood SPEIFITIONS ORDERING INFORMTION RP / 72 urrent Rating: 7.5 amps No. of ontacts: 6 Pin ontacts:.040 dia. brass, gold plated Socket ontacts: Spring temper phosphor bronze, gold plated Terminations:.048 dia. solder cup accepts up to # 20 WG stranded wire. Electrical Data: Dielectric withstanding voltage is one minute electrification at 3560 V. Dielectric: Molded Diallyl phthalate per MIL-M-14, type SDG-F. olor Gray. PM6PLS- onnector, plug with lock spring PM6SLR- onnector, receptacle with lock ring PM6PLR- onnector, plug with lock ring PM6SLS- onnector, receptacle with lock spring PM6P- onnector, plug without vibration lock PM6S- onnector, receptacle without vibration lock dd H- to above numbers when ordering hoods dd N- to above numbers when ordering nylon nut Polarization: ody design makes it impossible to make connection except in proper position. Mounting: able or panel mounted. Use nylon nut applied to either plug or receptacle. Lock Ring (and lock spring): Prohibits connector rotation on panel mounting and when engaged with lock spring, prevents accidental disconnection due to vibration, etc. Hood: Molded diallyl phthalate cable hood may be applied to either plug or receptacle.

73 SM Series Sub Miniature / # 20 - # 24 ontacts / 3 nd 7.5 mps N Nylon Nut SM2 Receptacle SM2P Plug SMH Hood Extreme compactness and lightweight of these subminiature connectors make them ideal for limited space application in ircraft. Portable Equipment and Instrumentation. SPEIFITIONS PHYSIL ND ELETRIL DT urrent Rating: SM1-7.5 amps; SM2, SM3-3 amps No. of ontacts: 1, 2, 3 Pin ontacts: SM dia. brass, gold plated SM2, SM dia. brass, gold plated Socket ontacts: Phosphor bronze, gold plated Terminations: SM dia. solder cup will accept up to # 20 WG stranded wire. SM2, SM dia. solder cup will accept up to # 24 WG stranded wire. urrent Rating Weight in Ounces P. R. * Wire Range SM1-7.5 mp SM1 - # 20 SM2-3 mp SM2 - #24 SM3-3 mp SM3 - # 24 Electrical Data: Dielectric withstanding voltage is one minute electrification at 1200 V. Dielectric: Diallyl Phthalate per MIL-M-14, type SDG-F. olor Gray. Polarization: ody design allows engagement in only one position. Mounting: Either plug or receptacle may be mounted on chassis or bulkhead with 1 /4-28 cadmium plated brass nut. dd N to code number to order. Hood: able hood may be applied to both plug and receptacle. dd H to code number. When ordering a hood separately, order P/N SMH. * Stranded RP / 73

74 SM Series Sub Miniature / # 20 - # 24 ontacts / 3 nd 7.5 mps Dimensions are for reference only and are subject to change. Outline drawings on request Hex Panel Opening.048 Dia. Solder up 1/4-28 UNF-2 THD..040 Dia. Receptacle SM1SN Plug SM1P Hood SMH /4-28 UNF-2 THD. 1/4-28 UNF-2 THD. Receptacle SM2SN Plug SM2P Hood SMH Receptacle SM3SN 1/4-28 UNF - 2 THD. Plug SM3P Hood SMH ORDERING INFORMTION SM 3 S H Step 1 Series ode: Series SM Step 3 No. of ontacts: 1, 2, 3 Step 4 ontact Type: P = Pin S = Socket Step 4 Type: N = Nut H = Hood RP / 74

75 M Series High Voltage Miniature / # 20 ontacts /.040" Dia. / 7.5 mps M4PLSH10 Plug with lock spring and hood M4SLRGN Receptacle with lock ring, ground lug and nut M10SLRN Receptacle with lock ring and nut M10PLSH19 Plug with lock spring and hood N Nylon Nut M12SLS12 Receptacle with lock spring M12P Plug M12H Hood with lock shell The extreme compactness and lightweight of M connectors make them ideal for such applications as strain gauges, telemetry and pressure pick-up installations in aircraft, portable equipment and instrumentation. SPEIFITIONS urrent Rating: 7.5 amps No. of ontacts: 4, 5, 7, 9, 10, 12 Pin ontacts:.040 dia. brass, gold plated Socket ontacts: Spring temper phosphor bronze, gold plated Terminations:.048 dia. solder cup accepts up to # 20 WG stranded wire. M dia. solder cup accepts up to # 20 WG stranded wire. Electrical Data: The dielectric withstanding voltage is one minute electrification at 1500 V. (2250 V for M12). Dielectric: rown mineral filled diallyl phthalate. lso available in gray glass filled diallyl phthalate, per MIL-M-14, SDG-F. Polarization: ody design permits engagement in proper position only. Mounting: For 1 /16" panel mounting of either plug or receptacle use cadmium plated brass nut for M4-10, nylon nut for M12. dd N to code number. Lock Ring (and lock spring): May be applied to plug or receptacle to stop connector rotation on panel. When engaged with lock spring, prevents accidental disconnection due to vibration, etc. Ground Lug: an be used to ground any of the 4 contacts on M4 connector. dd G to code number. Hood: nodized aluminum or brown mineral filled diallyl phthalate hoods may be applied to plug or receptacle of M4-M10. With or without cable clamps to provide additional strain relief for the cable. RP / 75

76 M Series High Voltage Miniature / # 20 ontacts /.040" Dia. / 7.5 mps Dimensions are for reference only and are subject to change. Outline drawings on request Dia Dia. Panel Opeming.09 Lock Ring (LR) Nut M21S Dia. Solder up /8-20 THD O Panel Drilling.50 3/8-24 UNF THD Receptacle M4S-LRGN Ground Lug (G).25 Nut & Lockwasher (N).69 3/8-24 UNF THD Lock Spring (LS) Plug M4P-LS (See Views elow) Dia. Solder up ccessory ode LR Lock Ring LS Lock Spring LN Nut & Lockwasher LN to be used as suffixes LN when required..56 /F Hex Nut Receptacle M*S-LRN Lockwasher 1/2-20 UNF THD. Plug M*P-LS 1/2-20 UNF THD Dia. 30 O.099 Dia. Panel Drilling (Viewed from Front of Panel) ontact rrangement M5S ontact rrangement M7S ontact rrangement M9S ontact rrangement M10S PHYSIL ND ELETRIL DT ontact locations are shown from terminal sides NOTE: ontact arrangement of M* P are reversed * Insert number, indicating number of contacts (5, 7, 9, 10) RP / 76 Weight In Ounces Solder Number up atalog of Lock Lock Lock Hole urrent Number ontacts Plug Rec. Nut Spring Ring Washer Dia./in. Rating M4P M4S amps M5P M5S amps M7P M7S amps M9P M9S amps M10P M10S amps M12P M12S amps

77 M Series High Voltage Miniature / # 20 ontacts /.040" Dia. / 7.5 mps MOLDED DILLYL PHTHLTE ND LUMINUM HOODS Molded diallyl phthalate cable hoods protect soldered wires and facilitate disengagement of connectors. able clamps provide additional strain relief and support. They are supplied on hoods with in the code number. lamps are cadmium plated with olive drab iridite finish. nodized aluminum hoods are precision machined from bar stock to give greater strength than die cast units. able clamps are machined as an integral part of the connector. The set screw prevents accidental disassembly from vibration, etc. polyethylene sleeve liner provides added insulation in the terminal area. Dimensions are for reference only and are subject to change. Outline drawings on request. standard hoods MX D F E WIDE x.313 HIGH LE OPENING SLOT 0.38 WIDE H9, H10, H19 M12H hood with cable clamps modified hoods F E H9, H10, H19, H19S D LE OPENING F D LE OPENING H9S, H19S special hoods special hood with cable clamps Used on onnectors M5, M7, M9, M10 D F.14 HG9, HG18 LE OPENING 1 /2-20 NF LE OPENING aluminum hoods HG WHEN ONNETED DI 4-40 SET SREW WHEN ONNETED.94 SET SREW (4-40) H14 For M4.22 LE OPENING.66 H16 For M5, M7, M9, M10.25 LE OPENING RP / 77

78 M Series High Voltage Miniature / # 20 ontacts /.040" Dia. / 7.5 mps PHYSIL DT Hood Used on DIMENSIONS ode of Weight In Number onnectors D E F-Thds Ounces H9 M5, 7, 9, / H10 M / H19 M5, 7, 9, / H9 M5, 7, 9, / H10 M / H19 M5, 7, 9, / H19S M5, 7, 9, / H9S M5, 7, 9, / H19S M5, 7, 9, / HG9 M5, 7, 9, / HG18 M5, 7, 9, / HG9 M5, 7, 9, 10 See Drawing.14 H14 M4 See Drawing.25 H16 M5, 7, 9, 10 See Drawing.25 H12H M12 See Drawing 1.10 ORDERING INFORMTION Omit steps not required M P/S Step 1 Series ode: M series Step 2 No. of ontacts: 4, 5, 7, 9, 10, 12 Step 3 ontact Type: P = Pin S = Socket Step 4 LS = lock spring LR = lock ring LS6 = M12 lock spring LR6 = M12 lock ring LS12 = lock spring for M12H hood Step 5 N = Nut Step 6 G = Ground lug (M4 only) Step 7 Hoods: See hood code number above. RP / 78

79 JF Series Miniature Side Mount / # 20 ontacts /.040" Dia. / 7.5 mps Dimensions are for reference only and are subject to change. Outline drawings on request. Side Mounting, 4 Position Rectangular 2 and 4 Position In-Line JF Series, PIN and Socket, 2 Position In-Line onnectors Dimensions shown are typical for all standard 2 position in-line connectors JF1S1P.09 Thru 'Sink x 82o JF1P1S.05 Solder up JF Series, PIN and Socket, 4 Position In-Line onnectors Dimensions shown are typical for all standard 4 position in-line connectors Solder up x JF4S.10 Thru 'Sink x 82o JF4P Side Mounting, 4 Position Rectangular, 2 and 4 Position In-Line JF Series, PIN and Socket, 4 Position Rectangular onnectors Dimensions shown are typical for all standard 4 position rectangular connectors Thru 'Sink x 82o Solder up JF2S2P JF2P2S RP / 79

80 D JF1S1PD4.343 R o.437 2x x.237 ±.015 Rack & Panel JF Series Miniature Side Mount / # 20 ontacts /.040" Dia. / 7.5 mps J F-2P 20 connectors assembled The versitile JF Series has a countersunk mounting hole and narrow width permitting exceptionally flat mounting. Maximum circuit density is provided with many positive polarizations. ustom multi-contact connectors are readily available by using the building block technique shown above. Dimensions are for reference only and are subject to change. Outline drawings on request. Typical onnector With DIP Solder Termination Straight Dip Solder Right ngle Dip Solder JF Series connectors may be ordered with dip solder and right angle terminations. onsult factory for availability. Typical onnectors ssemblies PIN ontact Pos. Socket ontact Pos. PIN ontact Pos. & D Socket ontact Pos. & D PIN ontact Pos., & D Socket ontact Pos., & D Socket Molding Socket ontact Pos. PIN Molding PIN ontact Pos. Socket Molding Socket ontact Pos. & PIN ontact Pos. & PIN Molding Socket Molding Socket ontact Pos. PIN Molding PIN ontact Pos. JF1S1P JF1P1S JF4S JF4 JF1S3P JF1P3S RP / 80

81 JF Series Miniature Side Mount / # 20 ontacts /.040" Dia. / 7.5 mps ORDERING INFORMTION 2 Position In-Line onnector JF 1S 1P Step 1 Series ode JF Step 2 ** Primary ontact and Molding Type Step 3 Secondary ontact ode Description ode If Step 2 equals 1S or 2S* Number of socket contacts 1P = 1S and socket molding. 1P or 2P* Number of pin contacts and 1S = 1P pin molding. 2SR* Number of socket contacts pin moldings. 2PR* Number of pin contacts socket moldings. *For two same type contacts, skip Steps 3 & 4. 4 Position In-Line onnectors JF4 S Step 4 Primary ontact Location ode = or Step 1 Series ode JF4 Step 2 ** Primary ontact and Molding Type ode Description S Socket contact and socket molding. P Pin contact and pin molding. Step 3 Primary ontact Location ode Number Of Primary ontacts,, or D = 1,, D,, D, or D = 2, D, D, or D = 3 For four same type contacts: omit step For four same type contacts with molding gender reversed, add R 4 Position Rectangular onnector JF 2S 2P Step 1 Series ode JF SPEIFITIONS Step 2 ** Primary ontact and Molding Type ode Description 1S, 2S, 3S or 2S2S Number of socket contacts and socket molding. 1P, 2P, 3P or 2P2P* Number of pin contacts and pin molding. 2S2SR* Number of socket contacts and pin molding. 2P2PR Number of pin contacts and socket molding. *For four same type contacts, skip Steps 3 & 4. Materials Moldings (PIN and Socket): Diallyl Orthophthalate Pin ontacts:.040 rass, gold plated Socket ontacts: Phosphor bronze, gold plated Step 3 Secondary ontact ode If Step 2 equals 3P = 1S 2P = 2S 1P = 3S 3S = 1P 2S = 2P 1S = 3P Step 4 Primary ontact Location ode Number Of Primary ontacts,, or D = 1,, D,, D, or D = 2, D, D, or D = 3 **For Pictorial Presentation, see RP/84 and RP/85 Performance haracteristics Dielectric Withstanding Voltage: 1500 V (at sea level) urrent Rating: 7.5 mps Operating Temperature Range: -55 O to +125 O Termination Type:.050 dia. solder cup to accept # 20 WG stranded wire. RP / 81

82 JF Series Miniature Side Mount / # 16 ontacts /.062" Dia. / 13 mps JF2H JF2P Hood and plug JF2S Receptacle JF2H Hood SPEIFITIONS For applications in electronic and communications equipment requiring miniature connectors with high current capacity. Series JF miniature connectors may be used in television, radio and communications urrent Rating: 13 amps No. of ontacts: 2 Pin ontacts:.062 dia. brass, gold plated Socket ontacts: Phosphor bronze, gold plated Terminations:.070 dia. solder cup will accept up to # 16 WG stranded wire. equipment. The countersunk side mounting hole and narrow width permits exceptionally flat mounting thereby minimizing connector protrusion when installed on equipment Electrical Data:Dielectric withstanding voltage is one minute electrification at 2925 V. Dielectric: Molded diallyl phthalate per MIL-M-14 Hood: Locked to connector by means of two side mounted straps. Dimensions are for reference only and are subject to change. Outline drawings on request JF 2 JF2H DI SOLDER UP DI DI HOLE.203 DI. X 82 O 'SINK OTH SIDE S (TYP) PHYSIL DT ND ORDERING INFORMTION RP / 82 J F-2S Receptacle Physical Data Number urrent Wire ode of Rating Size Weight Number ontacts mps.w.g. Ozs. JF-1P1S 1 Pin 1 Socket.082 JF-2PH 2 Pins 13 # JF-2SH 2 Sockets.046 (with hoods) JF-1S1P 1 Pin 1 Socket.082 JF-2P 2 Pins 13 # JF-2S 2 Sockets.046 (no-strapson hoods) JF2H Hood used on any of above 3 parts JF-2P Plug Mating ombinations JF-2H Hood JF2P mates with JF2S JF2PH mates with JF2SH JF1P1S- mates with JF1S1P- JF1P1S- mates with JF1S1P- JF1P1SH- mates with JF1S1PH- JF1P1SH- mates with JF1S1PH-

83 100 Series Removable ontacts 6x ctual Size Typical Removable ontact Winchester Electronics removable contacts allow quick, easy removal and replacement of any contact without disturbing another - and without discarding the connector. They offer exceptional flexibility in both the choice and revision of circuitry for rack and panel equipment... at substantial savings in replacement and installation time. In addition, wiring costs are significantly lowered, as wires may be assembled away from the connector itself. ssembly of contacts to wires is further simplified by crimp type contacts. contact is slipped on the wire, inserted in the crimping tool, and crimped securely in place in seconds. ompact and self-aligning, these removable contacts provide high retention force and exceptional mechanical and electrical reliability. Solder type removable contacts are available for connectors using MR contacts. SPEIFITIONS Pin ontacts: Socket ontacts: Tools: Military opper lloy, gold plated. losed entry type machined from copper alloy, gold plated. omplete line available. Includes automatic pneumatic, pneumatic hand operated, hand operated crimping tools, insertion and removal tools. Specifications: onforms to applicable portions of MIL Wire Sizes: From a minimum 28 to a maximum 14 WG. ll contacts are designed to accept a minimum WG conductor up to two sizes below maximum gage (each contact.) Termination Types: rimp, solder, dip solder or wire-wrap urrent Rating: 7.5 mps maximum for.040 contacts. 13 mps maximum for.062 contacts. To Order: Specify by catalog number Note: Series 100 Removable ontacts are not supplied with the connector. They must be ordered as a separate item. RP / 83

84 100 Series Removable ontacts 100 SERIES ONTTS 100 SERIES ONTTS RP / 84 Reeled Diameter For Loose ontacts For Loose ontacts For Reeled ontacts Loose ontact ccom- (See Drawings) ontact Part modates Used In Mating Description See MPS Gage Plug Hand Tool Positioner Gage Plug Pneumatic Depth Gage Plug Part Number onductor onnector Pin of Figure per Locator Hand Pneumatic Part Part Part Part Tool Part lock Part Part Number 2,000/Reel Sizes Series Diameter ontacts Number ont Tool Tool Number Number Number Number Number Number Number MR, TMR, rimp X, TX ontact P P MR, TMR, rimp X, TX ontact S S MR, TMR, rimp X, TX ontact P P MR, TMR, rimp X, TX ontact S S MR, TMR, rimp X, TX ontact P P MR, TMR, rimp X, TX ontact S S MR, TMR, rimp X, TX ontact P P MR, TMR, rimp X, TX ontact S S MR, TMR, rimp X, TX ontact P P MR, TMR, rimp X, TX ontact S S MR, TMR, rimp X, TX ontact P P MR, TMR, rimp X, TX ontact S S MR, TMR, rimp X, TX ontact P P MR, TMR, rimp X, TX ontact S S MR, TMR, rimp X, TX ontact P P MR, TMR, rimp X, TX ontact S S MR, TMR, rimp X, TX ontact P P MR, TMR, rimp X, TX ontact S S MR, TMR, rimp X, TX ontact P P MR, TMR, rimp X, TX ontact S S MR, TMR, rimp X, TX ontact P P MR, TMR, rimp X, TX ontact S S MR, TMR, rimp X, TX ontact P P MR, TMR, rimp X, TX ontact S S ontinued on page RP /85

85 100 Series Removable ontacts 100 SERIES ONTTS 100 SERIES ONTTS Reeled Diameter For Loose ontacts For Loose ontacts For Reeled ontacts Loose ontact ccom- (See Drawings) ontact Part modates Used In Mating Description See MPS Gage Plug Hand Tool Positioner Gage Plug Pneumatic Depth Gage Plug Part Number onductor onnector Pin of Figure per Locator Hand Pneumatic Part Part Part Part Tool Part lock Part Part Number 2,000/Reel Sizes Series Diameter ontacts Number ont Tool Tool Number Number Number Number Number Number Number 5 13 N/ Solder ontact Not MR, TMR, Solder vailable X, TX ontact P 6 13 N/ Solder ontact Not MR, TMR, Solder vailable X, TX ontact S 5 13 N/ Solder ontact Not MR, TMR, Solder vailable X, TX ontact P Not MR, TMR, Solder vailable X, TX ontact 6 13 N/ Solder ontact S 5 13 N/ Solder ontact Not MR, TMR, Solder vailable X, TX ontact P 6 13 N/ Solder ontact Not MR, TMR, Solder vailable X, TX ontact S 5 13 N/ Solder ontact Not MR, TMR, Solder vailable X, TX ontact P 6 13 N/ Solder ontact Not MR, TMR, Solder vailable X, TX ontact S 5 13 N/ Solder ontact Not MR, TMR, Solder vailable X, TX ontact P 6 13 N/ Solder ontact Not MR, TMR, Solder vailable X, TX ontact S 5 13 N/ Solder ontact Not MR, TMR, Solder vailable X, TX ontact P Not MR, TMR, Solder vailable X, TX ontact 6 13 N/ Solder ontact S N/ Solder ontact Not MR, TMR, Solder vailable X, TX ontact P N/ Solder ontact Not MR, TMR, Solder vailable X, TX ontact S N/ Solder ontact Not MR, TMR, Solder vailable X, TX ontact P N/ Solder ontact S Not MR, TMR, Solder vailable X, TX ontact rimp P P SRE, 42 Series See Drawing.030 ontact S S SRE, 42 Series See Drawing.030 rimp ontact P P SRE, 42 Series See Drawing.030 rimp ontact rimp S S SRE, 42 Series See Drawing.030 ontact rimp P P SRE, 42 Series See Drawing.030 ontact S S SRE, 42 Series See Drawing.030 rimp ontact MR, TMR, 3 Piece X, TX rimp S S MR, TMR, Piece X, TX rimp S S MR, TMR, 3 Piece X, TX rimp S S MR, TMR, Piece X, TX rimp S S ontinued on page RP /86 RP / 85

86 100 Series Removable ontacts 100 SERIES ONTTS 100 SERIES ONTTS RP / 86 Reeled Diameter For Loose ontacts For Loose ontacts For Reeled ontacts Loose ontact ccom- (See Drawings) ontact Part modates Used In Mating Description See MPS Gage Plug Hand Tool Positioner Gage Plug Pneumatic Depth Gage Plug Part Number onductor onnector Pin of Figure per Locator Hand Pneumatic Part Part Part Part Tool Part lock Part Part Number 2,000/Reel Sizes Series Diameter ontacts Number ont Tool Tool Number Number Number Number Number Number Number MR, TMR, Piece X, TX rimp S S MR, TMR, Piece X, TX rimp S S MR, TMR, Piece X, TX rimp S S Piece rimp S S SRE, 42 Series See Drawing Piece rimp S S SRE, 42 Series See Drawing Not SRE, 42 Series See Drawing Piece vailable rimp S Inner Outer ontact ontact Not RG178, MR, TMR, See Drawing.078 Shielded vailable 196/U X, TX rimp P Not RG178, MR, TMR, See Drawing.078 Shielded vailable 196/U X, TX rimp S Not RG161,179 MR, TMR, See Drawing.078 Shielded Not vailable 187/U X, TX rimp Required P Not RG161,179 MR, TMR, See Drawing.078 Shielded Not vailable 187/U X, TX rimp Required S Not RG174,188 MR, TMR, See Drawing.078 Shielded Not vailable 316/U X, TX rimp Required P Not RG174,188 MR, TMR, See Drawing.078 Shielded Not vailable 316/U X, TX rimp Required S 9 13 N/ Dip Solder Not Dip MR, TMR Not pplicable.062 Dip vailable Solder Solder N/ Dip Solder Not Dip MR, TMR Not pplicable.062 Dip vailable Solder Solder N/ Wire Wrap Not Wire SRE Not pplicable.030 Wire vailable Wrap Wrap N/ Wire Wrap Not Wire Wire SRE Not pplicable.030 vailable Wrap Wrap N/ Dip Solder Not Dip MR, TMR Not pplicable.062 Dip vailable Solder Solder N/ Dip Solder Not Dip MR, TMR Not pplicable.062 Dip vailable Solder Solder N/ Wire Wrap Not Wire MR, TMR Not pplicable.062 Wire vailable Wrap Wrap N/ Wire Wrap Not Wire Wire MR, TMR Not pplicable.062 vailable Wrap Wrap N/ Wire Wrap Not Wire MR, TMR Not pplicable.062 Wire vailable Wrap Wrap N/ Wire Wrap 8106 Not Wire MR, TMR Not pplicable.062 Wire vailable Wrap Wrap 100-S = Military ontacts ontinued on page RP /87

87 100 Series Removable ontacts MIL ONTTS MIL ONTTS ccom- Diameter M39029 Winchester modates Used In Mating Description See MPS MIL Spec Winchester Insertion Insertion Removal Removal MIL Spec Part Part onductor onnector Pin of Figure per rimp rimp Winchester Tool Tool Tool Tool Number Number Sizes Series Dia. ontacts Number ont Tool Tool Positioner Positioner MIL Winchester MIL Winchester M22520/ M22520/ M81969/ M81969/ R1001 rimp ontact M39029/ R-2020P M M22520/ M22520/ M81969/ M81969/ R1001 rimp ontact M39029/ R-1020P M M22520/ M22520/ M81969/ M81969/ R1001 rimp ontact M39029/ P M M22520/ uchn M81969/18-02 IT2857 M81969/20-02 RT2855 rimp ontact M39029/ M M22520/ M22520/ M81969/ M81969/ R1001 rimp ontact M39029/ R-2020S M M22520/ M22520/ M81969/ M81969/ R1001 rimp ontact M39029/ R-51020S M M22520/ M22520/ M81969/ M81969/ R1001 rimp ontact M39029/ S M M22520/ uchn M81969/18-02 IT2857 M81969/20-02 RT2855 rimp ontact M39029/ M RP / 87

88 100 Series Removable ontacts Figure 1 Figure 2 Figure 3 Figure 4 Figure 5 Figure 6 Figure 7 Figure 8 Figure 9 Figure 10 RP / 88

89 100 Series Removable ontacts Figure 11 Figure 12 Figure 13 Figure Figure 15 Figure Figure 17 Figure 18 ccepts O.062 pin. Figure 19 Figure 20 RP / 89

90 100 Series Removable ontacts Figure 21 Figure 22 Figure 23 Figure 24 Figure 25 Figure 26 Figure 27 Figure 28 ccepts.030 pin. Figure 29 Figure 30 RP / 90

91 100 Series Removable ontacts Figure 31 Figure 32 ORDERING INFORMTION atalog Dimensions Style able Sizes Number D E F G P Pin S Socket P Pin S Socket P Pin S Socket RG178/U RG196/U RG161/U RG179/U RG187/U RG174/U RG188/U RG316/U RP / 91

92 107 Series rimping Tools nd ccessories PNEUMTI ND HND RIMPING TOOLS utomatic Feed rimping Tool 600/1200 rimps Per Hour atalog Number ir operated tool provides for a large capacity reel and foot valve control. rimp depths are accurately controlled by interchangeable snap-in depth blocks when the tool is bench mounted. Leaves operator s hands free. (Does not include reel or foot valve control.) Includes crimp depth blocks. utomatic rimp Tool made up of bench mount ( ) and crimp t ool ( ). Used to crimp **P/S, **P/S, **S Series. Pneumatic Hand rimping Tool 400 rimps Per Hour atalog Number Requires 80/120 psi. rimp depth adjustment made by internal screw. Locators, adaptor sleeves, and gage plugs should be ordered separately. Locator and adapter supplied with tool. Miniature Hand Operated rimping Tool atalog Number This miniature version of the MS crimping tool is suited for the smaller crimp contacts such as the SRE series. It is only 7 1 /2 inches long and weighs 10 1 /2 ounces. Positioners are ordered separately. Hand Operated rimping Tool 200/300 rimps Per Hour atalog Number (Mil-T lass II Equivalent) Gage plugs should be ordered separately. Locator and Spanner wrench supplied with tool. Miniature Hand Operated rimping Tool atalog Number Miniature tool with a continuously variable crimp depth adjustment. Locators must be ordered separately. Hand Operated rimping Tool 200/500 rimps Per Hour atalog Number MS (Mil-T lass I) Ruggedly built hand tools with forged body, and four indentors machined from high grade tool steel. Size approximately 9 inches long. Weight approximately 19 ounces. Tool Kit atalog Number 107K4 Includes crimping tool , locator , insertion tool , removal tool 107R-1001, spanner wrench and go/no-go gages RP / 92