Mounting and Assembly of Sandwich Bodies
|
|
- Coleen Sims
- 6 years ago
- Views:
Transcription
1 Mounting and ssembly of Sandwich odies Mounting of ISO 0 (CEO ) Sandwiches Many of Sun s ISO 0 (CEO ) sandwich bodies are designed for multi-functional use to permit maximum circuit flexibility. With the exception of a limited range of sandwich bodies, Sun ISO 0 (CEO ) sandwich bodies do not have a counterbore for installing O-ring seals. Instead, Sun uses a special seal plate with a raised and a locating NOCH. Sun bodies incorporate oversize, symmetrical mounting holes to allow the bodies to be rotated about the Y axis and the X axis as shown in Figure. Rotation about the Y axis enables the and port connections to be interchanged and rotation about the X axis enables the and ports to be interchanged. ll Sun seal plates are manufactured to accommodate current industry standards regarding port and mounting bolt locations. Each Sun ISO 0 (CEO ) sandwich body is supplied with a locating hole which is drilled on each mounting face to position the body in the correct relationship to the ports and mounting holes. o further ensure that all bodies are located properly, all ISO 0 (CEO ) sandwich bodies are stamped with an arrow (or arrows) to show the relationship to the notch in the seal plate (see Figure ). Multi-function bodies are NOCH stamped for all possible mounting positions and all positions should be carefully inspected to be sure the intended function is correctly installed. ISO 0 (CEO ) Sandwich odies stamped with numbers to orient body for desired function he function symbols on the data pages for Sun s ISO 0 (CEO ) sandwich bodies (see Figure on page ) are shown with numbers (,,,) in the upper right and lower left hand corners. hese numbers correspond to numbers stamped on the face of the bodies and designate the functionality of the product. ecause many of these bodies can be used for different functions, the bodies are stamped to help the user orient the body for the function desired. he Meter-out and Meter-in functions are shown in the symbols with the numbers and, which stamped on the opposite face of the body. Sun Hydraulics echnical ips Sun offers sandwich and subplate mounted bodies for most of its cartridge functions. hese mounting configurations are complete circuit elements that mount under directional control valves. Similar to other Sun mounting configurations, the sandwich and subplate bodies are available in aluminum and ductile iron material. 50 (,7mm) Diameter, laces for -- 0 O-rings ssembly of ISO 0 (CEO ) Sandwiches.... NOCH.05 (,7mm) Y Rotation xis 0 (5,mm) Diameter, laces X Rotation xis Locating in Hole.0 (,0mm) Locating in Figure. ody Rotation Reference Rotation on the Y xis X Rotation xis lace the seal plate on the subplate mounting surface with the nib facing outward or away from the subplate and the locating pin hole on the seal plate aligned with the pin hole on the subplate mounting surface. t this point, the NOCH in the seal plate should be adjacent to the port of the valve interface. See Figure. osition the Sun sandwich body so that the control NOCH arrow for the required function points to the NOCH in the seal plate. See Figure. Move the sandwich body as required to engage the on the seal plate with the clearance hole in the body. NOE: In every installation, the seal plate nib must be oriented toward the directional control valve and away from the subplate or manifold. ll locating S in the sandwich valve stack must point away from the subplate. fter determining the correct alignment of the sandwich body to the seal plate, lift the body and plate together, turn Meter-in NOCH ssembly Figure. ssembly Sun Sandwich Locking in Sun Seal late Subplate or Manifold Sandwich ody ech ips: Web # Rev. 0-R-5 00 Sun Hydraulics Corporation
2 Sun Hydraulics echnical ips the assembly over and locate the correct hole in which to press the locating pin. he locating pin is shipped separately. ress the pin, serrated end first, into the body until it stops. he pin must protrude below the seal plate to positively align with the mounting surface. If a valve stack requires disassembly at anytime, the pin should not be removed. It will simplify the reassembly of the valve stack. NOE: Not all manufacturers of subplates offer a pin clearance hole which requires the pin to be omitted. 5. fter all the body alignments have been determined and all pins installed, assemble the valve stack in the required functional order. Make sure all the O-rings are properly positioned. Install the directional control valve on top of the stack and tighten the stud nuts alternately to the proper torque of 0-5 lb.in. (,5 5,0 Nm). Steps to void Seal late Leaks Make sure the mounting surface is flat and without burrs. Do not polish the mounting surface. (Machining marks help to keep the O-rings from acting as pumps.) Remove any dings on the corners of seal plates that could create gaps. Studrods or cap screws must not bottom out in the threaded mounting holes. It is very important to keep all of the o-ring sealing surfaces dry. he hydrostatic properties of an oil film under the o-rings, and at the seal plate interface, can SE SE egin with body view showing stamped number in lower left corner. Note the location of,,, and ports and the position of the cavity. his position places the port of the sandwich nearest to the viewer. he sandwich is now oriented for the meter out function. Rotate the sandwich on the X axis to orient body for meter-in function. Meter-out Function Meter-in Function function symbol for G NOCH in function symbol for G NOCH in SE SE Rotate the sandwich on the Y axis to orient body for meter-out function. Rotate the sandwich on the X axis to orient body for meter-in function. Meter-out Function Meter-in Function function symbol for G NOCH in function symbol for G NOCH in Figure : Steps through : Orientation Example for ISO 0 (CEO ) Sandwich ody G Sandwich ody ech ips: Web # Rev. 0-R-5 00 Sun Hydraulics Corporation
3 Sun Hydraulics echnical ips create a fluid path leading from the pressurized port to the outside edge of the stack. (Under this condition, as noted in step, an O-ring can actually act as a pump.) Warning: If you start with a wet seal interface in your stack, there s a good chance it will always stay wet! Orientation Example for ISO 0 (CEO ) bodies Steps through in Figure on page describe in detail the steps for the orientation of a G sandwich body. Mounting ISO 05 (CEO 5) Sandwich odies Sun ISO 05 (CEO 5) sandwich bodies are available for many mounting configurations. he standard ISO 05 (CEO 5)/NF D05 is offered with two methods of sealing the fluid interface. he sealing method depends on the ability of the body to be rotated about its Y axis. Sandwich bodies that can be rotated will use a Sun seal plate supplied with the body. Non rotating bodies will have counterbores machined into the body sealing surface for O-ring placement. he ISO 05 (CEO 5) sandwich body can only be rotated about the Y axis referred to in the ISO 0 (CEO ) sandwich section. (here is no on the ISO 05 (CEO 5) subplate,) X axis rotation is not possible due to the lack of symmetry of the fluid ports. Mounting ISO 05 (CEO 5) x, y Sandwich odies Sun ISO 05 (CEO 5) x, y sandwich bodies are furnished with pilot and drain connections. Due to the differences in the U.S. and European seal plates, none are supplied with these bodies. hey must be ordered separately to correctly match the other valve bodies in the stack. See able for Retainers on page. Sandwich ody ech ips: Web # Rev. 0-R-5 00 Sun Hydraulics Corporation
4 Sun Hydraulics echnical ips REINERS ND SELS FOR SNDWICH VLVES attern Interface Seal Retainer Only Seal Retainer Retainer Number Seals Seal Kit Only Seal and Seal Retainer Kit Kit Container Kit Number Kit Number ISO 0 (CEO ) NF D0 Was NF D0: ISO 0 (CEO ) 99-0 ) ) ISO 05 (CEO 5) NF D05 Was NF D0: ISO 05 (CEO 5) ISO 05 x, y 0H U.S ISO 05 x, y (CEO 5) RS5H ISO 07 (CEO 7) NF D07 Was NF D0: ISO 07 (CEO 7) ISO 08 (CEO 8) NF D08 Was NF D06: ISO 08 (CEO 8) ) ) ) ) ) ) ) ) ) ) ) ) ) ) ) ) ) ) Sandwich ody ech ips: Web # Rev. 0-R-5 00 Sun Hydraulics Corporation
5 Sun Hydraulics echnical ips SUDNUS ND SUDKIS FOR SNDWICH ODIES Studkits for ISO 0 (CEO ) and ISO 05 (CEO 5) Sandwich odies o simplify the installation of ISO 0 (CEO ) and ISO 05 (CEO 5) sandwiches, Sun offers uncut (can be cut to length in the field) or precut studkits in both inch and metric standard threaded rod. Once the rods are installed in a subplate or manifold, they act as a guide in assembling the sandwich body stack. fter the directional control valve is assembled on top of a stack, Sun studnuts are used to retain the assembled stack. he inch and metric studrods are both made of high tensile, fully threaded SM--9 Grade material with the following mechanical properties: 5,000 psi (86 Ma) minimum tensile strength. 05,000 psi (7 Ma) minimum yield point. 6 Rc hardness. he studnuts are special hex socket nuts with the following features: n outside diameter equivalent to a standard socket head cap screw. Full thread engagement as shown below. Mechanical stop between the internal hex and the thread to prevent the hex wrench from being pushed out of its socket. See Figure.. (0, mm).65 (5,9 mm).56 (, mm).000 (5, mm) Figure. Studnuts Internal Hex Size 5/ ( mm) 0- (art #50005) and M5 (art #50009) Studnuts Internal Hex Size /6 (5 mm) /-0 (art #5000) and M6 (art #50008) Studnuts ISO 0 (CEO ) SUDKIS: RECOMMENDED ORQUE: 0-5 lb. in. (,5-5,0 Nm) ) 0- Studnuts INCH SNDRDS MERIC SNDRDS Kit Contents Kit Number Kit Contents Kit Number 7 (78 mm) long 0- Studrods ) 0- Studnuts (05 mm) long 0- Studrods 50) 0- Studnuts 0- Studrods ) M5 Studnuts 7 (78 mm) long M5 Studrods ) M5 Studnuts long (05 mm) long M5 Studrods 50) M5 Studrods M5 Studrods ) 0- Studrods ) M5 Studnuts ) 0- Studnuts ) 0- Studnuts ) 0- Studrods length +.06 (+,5 mm) ) M5 Studnuts ) M5 Studrods length: +.06 (+,5 mm) Sandwich ody ech ips: Web # Rev. 0-R-5 00 Sun Hydraulics Corporation
6 Sun Hydraulics echnical ips ISO 05 (CEO 5) SUDKIS: RECOMMENDED ORQUE: 05-0 lb. in. (,0-,5 Nm) INCH SNDRDS MERIC SNDRDS Kit Contents Kit Number Kit Contents Kit Number 7 (78 mm) long /-0 Studrods (05 mm) long /-0 Studrods 50) /-0 Studnuts /-0 Studrods ) M6 Studnuts 7 (78 mm) long M6 Studrods ) M6 Studnuts long (05 mm) long M6 Studrods 50) M6 Studrods M6 Studrods ) /-0 Studrods ) M6 Studnuts ) /-0 Studrods length: +.06 (+,5 mm) ) M6 Studnuts ) M6 Studrods length: +.06 (+,5 mm) SUDROD LENGH DEERMINION CHR orque: 0 lb. in. (,0 Nm) Solenoid orque: 5 lb. in. (5,5 Nm).0 (0, mm) rojection into Studnut Solenoid.56 (, mm) rojection into Studnut Sandwich X* otal Height of Stack Effective olt otal Studrod +.06 (+,5 mm) Sandwich X* otal Height of Stack otal Studrod +.06 (+,5 mm) Effective olt Subplate.8 (9,7 mm) rojection into Subplate Subplate. (, mm) rojection into Subplate ISO 0 (CEO ) ISO 05 (CEO 5) ISO 05 x,y (CEO 5 x,y) Model X inches* X mm* Model X inches* X mm* Continental E0M.65 5,9 VSM., Continental VS5M.65 5,9 ED05M., Double (Vickers) Q*-.56 6,9 Q* ,7 arker-hannifin DVW.50 8, DW.9 8,5 Racine osch.5ng6.87, /.8 5, Rexroth WR6.6,0 WE0, WEH0.8 0,0 Dynex/Rivett 6500 Series 0., ,7 Vickers/0 DGV.56 9, DGS.05 6,7 Vicker/60 DGV.8, DGV5.8 0,0 Nachi SSG0. 6,6 SSG0, E0, E0.8 60,5 * he X dimension was accurate as of the publication date of this information. Verify in the applicable manufacturers literature. Sandwich ody ech ips: Web # Rev. 0-R-5 00 Sun Hydraulics Corporation
Sandwich Bodies TECHNICAL PRODUCT INFORMATION
Sun offers sandwich and subplate mounted bodies for most of its cartridge functions. hese mounting configurations are complete circuit elements that mount under directional control valves. Similar to other
More informationDirectional Control Valves. General Description. Operation. Features
echnical Information General Description W directional control valves are 5-chamber, pilot operated, solenoid controlled valves, hey are available in 2 or 3-position styles. hese valves are manifold or
More informationDirectional Control Valves. Features. Application. Operation
Introduction pplication hydraulic directional control valves are high performance, solenoid controlled, pilot operated, 2-stage, 4-way valves. hey are available in 2 or 3-position styles and are manifold
More informationDirectional Control Valves Series D81V. General Description. Operation. Features. Specifications
echnical Information General Description W directional control valves are 5-chamber, pilot operated, solenoid controlled valves. hey are available in 2 or 3-position styles. hese valves are manifold or
More informationDirectional Controls
VICKERS Directional Controls Solenoid Operated Directional Control Valves NF D05, ISO-4401-05 DG4S*-01**-5* ir Gap ype Revised 8/97 671 able of Contents DG4S*-01 Model Code..................................................................................
More informationDirectional Control Valves. Features. Application. Operation
Catalog HY14-2502/US Introduction pplication Series D31 hydraulic directional control valves are high performance, solenoid controlled, pilot operated, 2-stage 4-way valves. hey are available in 2 or 3-
More informationDirectional Control Valves. General Description. Operation. Features
echnical Information Series D61VW General Series D61VW directional control valves are 5-chamber, pilot operated, solenoid controlled valves, hey are available in 2 or 3-position styles. hese valves are
More informationAccessories. Subplates and Connection Plates for Four-Port Directional Valves. Vickers. ISO 4401, 02/03/05/07/08 General Description.
Vickers ccessories Subplates and Connection lates for Four-ort Directional Valves ISO 4401, 02/03/05/07/08 General Description his range of subplates and auxiliary connection plates offers an economical
More informationDirectional Control Valves. General Description. Operation. Features
echnical Information Series D101VW General Series D101VW directional control valves are 5-chamber, pilot operated, solenoid controlled valves. hey are available in 2 or 3-position styles. hese valves are
More informationDirectional Control Valves. Application. Features. Operation
Catalog HY14-2502/US Introduction pplication Series D81 hydraulic directional control valves are high performance, solenoid controlled, pilot operated, 2-stage, 4-way valves. hey are available in 2 or
More informationDirectional Control Valves. Application. Features. Operation. D3W Solenoid Operated Conduit Cavity Style. D3W Solenoid Operated Hirschmann (DIN) Style
Catalog HY14-2500/US Introduction pplication Series D3 hydraulic directional control valves are high performance, direct operated 4-way valves, available in 2 or 3-position. hey are manifold mounted which
More informationHydraulics 1. Directional Control Valves Series D1M. Features. Application. Operation. D1MW Solenoid Operated Free Lead Wire
ulletin 2544-1/US Introduction pplication arker D1M Series hydraulic directional control valves are high performance, direct operated 4-way valves. hey are available in 2 or 3 position styles. hey are
More informationProduct Tips and Features
2.00.01 02/2002. Manifolds & Valve acks roduct ips and Features apping lates apping lates are sandwich adapters designed to provide a means to easily take pressure readings from the work ports. 1. Standard
More informationDirectional Controls
Vickers Directional Controls Mechanical ctuators Directional Control Valves Directional Control Valves 310 bar (4500 psi) Flows to 114 l/min (30 USgpm) NF D05, ISO-4401-05 DG1V4-01**-10 Knob Operated DG17V4-01**-10
More informationDirectional Control Valves. Application. Features. Operation
Catalog HY14-2500/US Introduction pplication Series D81 hydraulic directional control valves are high performance, solenoid controlled, pilot operated, 2-stage, 4-way valves. hey are available in 2 or
More informationEManually Operated Directional Valves
DIRECIONL CONROLS hese valves may be used to manually shift the spool position and change the direction of oil flow. hreaded Connections Sub-late Mounting Specifications DM--C - DM--D - DM--D - DM-- -
More informationIndustrial Hydraulic Valves. Directional Control, Pressure Control, Sandwich, Subplates & Manifolds, Accessories. Catalog HY /US
LH SECION Industrial Hydraulic Valves Directional Control, ressure Control, Sandwich, Subplates & Manifolds, ccessories echnical Information General Description Series D61VW directional control valves
More informationDirectional Control Valves
echnical Information General Description he D1VW Series directional control valves are highperformance, 4-chamber, direct operated, wet armature solenoid controlled, 3 or 4-way valves. hey are available
More informationManapak Sandwich Valves. General Description
echnical Information Series RM General Description RM Series relief valves limit system pressure by opening to tank when system pressure reaches the valve setting. With D3 size, they can also be configured
More informationDirectional Control Valves. Application. Features. Operation.
Catalog HY14-2500/US Introduction pplication Series D101 hydraulic directional control valves are high performance, solenoid controlled, pilot operated, 2-stage, 4-way valves. hey are available in 2 or
More informationOperation. D1VW Solenoid Operated Plug-In Conduit Box Style
Introduction pplication hydraulic directional control valves are high performance, direct operated 4-way valves. hey are available in 2 or 3-position styles. hey are manifold mounted valves, which conform
More informationOperation. D3W Solenoid Operated Conduit Box Style. D3W Solenoid Operated Hirschmann (DIN) Style
Catalog HY14-252/US Introduction pplication arker D3 Series hydraulic directional control valves are high performance, direct operated 4-way valves, available in 2 or 3 position. hey are manifold mounted
More informationUSA Headquarters. Dynex/Rivett Inc. 770 Capitol Drive Pewaukee, WI U.S.A. Tel: FAX:
SECIFICIONS D05H attern Directional Control Valves lso refer to "Directional Valve Features, Selection and Operating Recommendations" (dynexdcvoperating.pdf) CONC INFORMION US Headquarters 770 Capitol
More informationSeries Shockless Type Solenoid Controlled Pilot Operated Directional Valves
Solenoid Controlled ilot Operated Directional Valves Electronic Circuit X Specifications Descriptions G-DSHG-4-3C - - - -/9 G-DSHG-6-3C - - - -/9 Max. Flow /min (U.S.GM) 16 (4.3) (66.1) 1 1 Max. Operating
More informationELECTRICAL OPERATED DIRECTIONAL CONTROL VALVE
ELECTRICAL OPERATED DIRECTIONAL Working pressure: 315 bar Size: Cetop 3 and Cetop 5 Interchangeable to all the major hydraulic directional valves: Rexroth 4WE6-4WE10 Vickers DG4V-3 - DG4V-5 Denison 4D01-4D02
More informationVickers. Service Data. Vane Pumps. Vane Type Triple Pump (F3) 2520VQSV10* ***** ******* 20* M 2492 S. Released
Service ata Vickers Vane Pumps Vane Type Triple Pump (F3) 2520VQSV10* ***** ******* 20* Released 08 01 95 M 2492 S 10 SE rated capacity (V10 cover end cartridge) USgpm Rotor Vane Kit Ring Pin Pin olt olt
More informationVickers. Service Data. Vane Pumps. Vane Type Triple Pump (F3) 4525VQSV10* ***** ******* 20* Released M 2496 S
Service ata Vickers Vane Pumps Vane Type Triple Pump (F3) 4525VQSV10* ***** ******* 20* Released 08 01 95 M 2496 S 10 SE rated capacity (V10 cover end cartridge) USgpm Rotor Vane Kit Ring Pin Pin olt olt
More informationEManually Operated Directional Valves
DIRECIONL CONROLS hese valves may be used to manually shift the spool position and change the direction of oil flow. hreaded Connections Sub-late Mounting Specifications DM--C - DM--D - DM--D - DM--B -
More informationHigh Pressure, Subplate Mounted Directional Control Valves
ENGINEERING SECIFICIONS High ressure, Subplate Mounted Directional Control Valves MODEL H05 5 gpm (19 L/min) nominal 8000 psi (560 bar) Sliding-spool H05 valves provide true four-way control in a simple
More informationDirectional Control Valves
Frequently sked Questions Frequently sked Questions What is the function of a directional control valve? directional control valve is the extend and retract control for your hydraulic cylinders. It provides
More informationAppendix ISO /03/05/07/08
ppendix ISO4401 02/03/05/07/08 Fluid Recommendations Viscosity & Cleanliness Recommendation Minimum Optimum Maximum ISO Cleanliness 6.0 cst 20 43 cst 2158 cst 20/18/15 (45 SUS) (100-200 SUS) (10000 SUS)
More informationProportional Valves. Auxiliary Function Modules for Proportional Valves. Hydrostat, Parallel-Flow-Path, Pilot Shuttle and Tapping Modules
June 1996 G-459 VICKERS roportional Valves uxiliary Function Modules for roportional Valves Hydrostat, arallel-flow-ath, ilot Shuttle and Tapping Modules Functional Symbols For typical applications of
More informationOperation. D1VW Solenoid Operated Plug-In Conduit Box Style
Introduction pplication hydraulic directional control valves are high performance, direct operated 4-way valves. hey are available in 2 or 3-position styles. hey are manifold mounted valves, which conform
More informationDirectional Control Valves
Frequently sked Questions N-1 Frequently sked Questions What is the function of a directional control valve? directional control valve is the extend and retract control for your hydraulic cylinders. It
More informationUSA Headquarters. Dynex/Rivett Inc. 770 Capitol Drive Pewaukee, WI U.S.A. Tel: FAX:
SECIFICIONS D0H attern Directional Control Valves lso refer to "Directional Valve Features, Selection and Operating Recommendations" (dynexdcvoperating.pdf) CONC INFORMION US Headquarters 770 Capitol Drive
More informationDirectional Control Valves. Features. Application. Operation
Introduction pplication Series D31 hydraulic directional control valves are high performance, solenoid controlled, pilot operated, 2-stage, 4-way valves. hey are available in 2 or 3-position styles and
More informationIndustrial Hydraulic Valves. Directional Control, Pressure Control, Sandwich, Subplates & Manifolds, Accessories. Catalog HY /US
LH Industrial Hydraulic Valves Directional Control, ressure Control, Sandwich, Subplates & Manifolds, ccessories Catalog HY14-2500/US echnical Information General Description Series D1VW directional control
More information"G" SERIES SHOCKLESS TYPE SOLENOID OPERATED DIRECTIONAL VALVES G-DSG-01/03 (1/8, 3/8) "G" SERIES SHOCKLESS TYPE
"G" SRIS SHOCKLSS Y NOID ORD DIRCIL VLVS G-DSG-1/3 (1/, 3/) "G" SRIS SHOCKLSS Y NOID CROLLD ILO ORD DIRCIL VLVS G-DSHG-/ (1/, 3/) Mounting Up to 5 Ma (33 SI), 5 L /m in (.1 U.S.GM) ub. C-5 DIRCIL CROLS
More informationDirectional Controls
Vickers Directional Controls ilot Operated Directional Valves DG3V-10 Hydraulic ilot Operated; 1100 l/min (290 USgpm) 350 bar (5000 psi) DG5V-10 Solenoid ilot Operated; 1100 l/min (290 USgpm) 350 bar (5000
More informationISO 05 SANDWICH BODIES
ISO 5 SNDWICH ODIES luminum rated to 3 psi and Ductile Iron rated to 5 psi. See page viii for ordering cartridge/body and seals. ressure ratings, material specifications on page xiv. FUNCION 3..81 to 1
More informationHigh Pressure, High Flow Rate Modular Valves
eatures Installation and mounting space can be minimized. No special skill is required for assembly and any addition or alternation of the hydraulic circuit can be made quickly and easily. roblems such
More informationISO 05 SANDWICH BODIES
ISO 5 SNDWICH ODIES luminum rated to 3 psi and Ductile Iron rated to 5 psi. See page viii for ordering cartridge/body and seals. ressure ratings, material specifications on page xiv. FUNCION 3. 1. ir leed
More informationISO 4401 size 07; 315 bar (4500 psi); up to 200 L/min (53 USgpm) General Description
Vickers SystemStak SystemStak Valves ISO 441 size 7; 315 bar (45 psi); up to 2 L/min (53 USgpm) General Description This range of stackable hydraulic controls are designed to be mounted under a size 7
More informationDT (700 Series) Hydraulic Motor
DT (700 Series) Hydraulic Motor shafts 45 60mm Tapered 47 2-1/4 Straight 16.0 [.631] 15.9 [.629] 10.0 [.395] 9.9 [.391] 35 [1.37] 7 [.29] *120 [4.73] 70 [2.75] 38.9 [1.530] 37.6 [1.480] 12.7 [.501] 12.7
More informationHigh Response Type Proportional Electro-Hydraulic Directional and Flow Control Valves
igh Response ype roportional Electro-ydraulic s igh response, high precision and high reliability are achieved by a combination of compact and powerful solenoid and spool-position-detection LVD. Direct
More informationRA / Pressure Reducing Valve, Pilot Operated Model DR (Series 5X) Ordering code 1/ PSI (350 bar) GPM (400 L/min)
R 26 892/06.98 Pressure Reducing Valve, Pilot Operated Model DR (Series 5) Size 10 to 0... 5000 PSI (50 bar)... 105 GPM (400 L/min) R 26 892/06.98 Replaces: 05.94 Pilot operated pressure reducing valve
More informationUSA Headquarters. Dynex/Rivett Inc. 770 Capitol Drive Pewaukee, WI U.S.A. Tel: FAX:
SPECIFICAIONS D05 Pattern Directional Control Valves Also refer to "Directional Valve Features, Selection and Operating Recommendations" (dynexdcvoperating.pdf) CONAC INFORMAION USA Headquarters Dynex/Rivett
More informationD03 FluiDyne Valves. ENGINEERING DATA
ENGINEERING D D3 FluiDyne Valves 4 Way, and 3 Postion Solenoid Operated Variety of Voltage and Spool Configurations Same Day Shipments 1 Month Warranty www.fluidynefp.com D3 FluiDyne Valves: 4 Way, and
More informationOperation. D1VW Solenoid Operated Plug-In Conduit Box Style
Catalog HY14-2500/US Introduction pplication hydraulic directional control valves are high performance, direct operated 4-way valves. hey are available in 2 or 3-position styles. hey are manifold mounted
More information8.5 Service of the Actuator PNC4508M02 Series
8.5 Service of the ctuator N4508M02 Series 8.5.1 echnical Data N4508M02-F, N4508M02-R Doc003635.png Doc003653.png () (B) () LOSED O OOLING ctuator, bolted to manifold. Valve pin operation Operation medium
More information155 CARTRIDGE SINGLE SEAL
MECHANICAL SEAL INSTALLATION INSTRUCTIONS 155 CARTRIDGE SINGLE SEAL SEAL INSTALLATION Preparation Determine if the pump is in good condition. A. Check the shaft or sleeve. 1. Remove all burrs and sharp
More informationUSA Headquarters. Dynex/Rivett Inc. 770 Capitol Drive Pewaukee, WI U.S.A. Tel: FAX:
SPECIFICIONS D08H Pattern Directional Control Valves lso refer to "Directional Valve Features, Selection and Operating Recommendations" (dynexdcvoperating.pdf) CONC INFORMION US Headquarters 770 Capitol
More informationEMechanically Operated Directional Valves
E DIRECIONL CONROLS Cam Operated Directional Valves hese valves may be used to shift the direction of oil flow by depressing the spool by way of a cam. Specifications Max. Operating Max. -Line Max. Flow
More information01 SERIES MODULAR VALVES. Pub. EC-1402
SERIES General Information Mounting Surface : ISO --3--, CEO-3, N-D Up to 3.5 Ma (57 SI), 35 L /m in (9.5 U.S.GM) ub. EC- MODULR VLVES he modular valves are functional elements with which a hydraulic system
More information03 SERIES. General Information Mounting Surface : ISO 4401-AC-05-4-A, CETOP-5, NFPA-DO2 Up to 25 MPa (3630 PSI), 70 L /min (18.5 U.S.
3 SERIES General Information Mounting Surface : ISO 44-C--4-, CETO-, N-DO Up to Ma (363 SI), 7 L /min (8. U.S.GM) ub. EC-43 MODULR VLVES The modular valves are functional elements with which a hydraulic
More informationDirectional Controls
VICKERS Directional Controls DG3V-7, 20 Series, ilot Operated DG5V-7, 40 Series, Solenoid Controlled, ilot Operated ISO 440 Size 07 ypical Section DG5V-7-2C Spring-Centered Valve Example Basic Characteristics
More information4 Flow Control Valves. Notes
Flow Control alves Content Flow Control alves Notes Example Flow l/min (GM) ressure bar (I) Code Cartridge ize ; D ize ; D ize ; D Line Mounted age Data heet Needle - Restrictor alves and alves with Reverse
More informationProduct Tips and Features
5.00.01 anifolds & Valve Packs Product Tips and Features Circuits Relief from P to T are designed to provide a means to connect a single solenoid valve to field piping either on the power unit or near
More informationDirect Operated Proportional DC Valves
echnical Information Direct Operated roportional DC Valves Series D1F and D3F General Series D1F and D3F directional control valves of nominal sizes NG6 (CEO 3) and NG10 (CEO 5) respectively, provide variable
More informationMRK 25 M a r k 2 5 d i r e c t s o l e n o i d a c t u a t e d v a l v e s T C H N C L T V L V M
MRK 25 SRS direct solenoid actuated valves MRK 25 MRK 25 M a r k 2 5 d i r e c t s o l e n o i d a c t u a t e d v a l v e s T C H N C L T................................................... 3 V L V M O
More informationBankable Control Valves
Hydraulics ankable Control Valves Catalog 3123/US Catalog 3123/US Contents ankable Control Valves WRNING FILURE OR IMROER SELECION OR IMROER USE OF HE RODUCS ND/OR SYSEMS DESCRIED HEREIN OR RELED IEMS
More informationPilot Operated Directional Valves
ilot Operated Directional Valves Catalog DG3V-10 Hydraulic ilot Operated; 1100 l/min (290 USgpm) 350 bar (5000 psi) DG5V-10 Solenoid ilot Operated; 1100 l/min (290 USgpm) 350 bar (5000 psi) NF D10, ISO-4401-10,
More informationVER03MP CONTINENTAL HYDRAULICS PROPORTIONAL PRESSURE RELIEF VALVES PILOT OPERATED VER03MP - PROPORTIONAL PRESSURE RELIEF VAVLES PILOT OPERATED
CONTINENTAL HYDRAULICS VER03MP PROPORTIONAL PRESSURE RELIEF VALVES PILOT OPERATED VER03MP - PROPORTIONAL PRESSURE RELIEF VAVLES PILOT OPERATED 5505 WEST 123RD STREET SAVAGE, MN 55378-1299 / PH: 952.895.6400
More information3/2 and 4/2 directional poppet valve with solenoid actuation
Courtesy of CM/Flodyne/Hydradyne Motion Control Hydraulic neumatic Electrical Mechanical (800) 426-5480 www.cmafh.com 3/2 and 4/2 directional poppet valve with solenoid actuation ype M-.SED Size 10 Component
More informationPROPORTIONAL PRESSURE RELIEF VALVES PILOT OPERATED WITH OBE
CONTINENTAL HYDRAULICS VER03MPG PROPORTIONAL PRESSURE RELIEF VALVES PILOT OPERATED WITH OBE VER03MPG - PROPORTIONAL PRESSURE RELIEF VAVLES PILOT OPERATED WITH OBE 5505 WEST 123RD STREET SAVAGE, MN 55378-1299
More informationDirectional control valves NG6...NG32 D03...D10 6
Directional control valves NG6...NG32 D03...D10 6 DIRECIONL CONROL VLVES 1 Index DO3 (NG6) age 2 to 22 D05 (NG10) age 23 to 42 D07 (NG16) age 43 to 54 D08 (NG25) 3000 SI age 55 to 65 D08 (NG25) 4600 SI
More informationAir Valve AIR-PILOTED VALVES
K-UV002 Ver.1.0 ir Valve I-ILOTED VLVES INSTUCTI MNUL Ver.1.0 ir-piloted Valves Features Since the unit requires air piping only, with no need for electrical wiring, it can be handled by a person without
More informationREPAIR PROCEDURES MANUAL
REPAIR PROCEDURES MANUAL PVX Series Vane Pumps A Design Series Step-by-Step Guide to Troubleshooting and Repairing PVX Series Vane Pumps Introduction Thank you for choosing Continental Hydraulics PVX Vane
More informationRelief Valves 24,6. T 10A Cavity Locating Shoulder Depth 0,8 .25 NPTF CBE CBE/S.25 BSPP CBE/M CBE/T. Relief Valves 49,3 25,1 27,2
ISO 5 SNDWICH ODIES luminium rated to 1 bar and S Iron rated to 35 bar. See page viii for ordering cartridge/body and seals. ressure ratings, material specifications on page xiv. FUNCION to 4,6 4,6 3,
More informationDirectional Control Valves. General Description. Features. Specifications
echnicl Informtion Generl Description directionl control vlves re high performnce, 5-chmer, direct operted, wet rmture, solenoid controlled, 3 or 4-wy vlves. hey re ville in 2 or 3-position nd conform
More informationRelief Valves 43,2 21,6. T 10A Cavity Locating Shoulder 1,3 Depth 0,8 .25 NPTF FBP FBP/S.25 BSPP FBP/M FBP/T
ISO 3 SNDWICH ODIES luminium rated to bar and S Iron rated to 35 bar. See page viii for ordering cartridge/body and seals. ressure ratings, material specifications on page xiv. 3 x y X Y Model Code List
More informationRA / Accumulator unloading valve, pilot operated, Model DA 6 V.., series 4X. Ordering details DA 6 V 4X. Preferred models 1/8.
R 26 404/06.9 ccumulator unloading valve, pilot operated, Model D 6 V.., series 4X Size 6 up to 4500 SI (315 bar) up to.00 GM (30 L/min) R 26 404/04.9 Features: For subplate mounting: porting pattern to
More informationHydraulic Fluids. Note: For use with hydraulic fluids other than those listed above, please consult your Yuken representatives in advance.
Hydraulic Fluids Fluid Types Any type of hydraulic fluids listed in the table below can be used. Petroleum base oils Use fluids equivalent to ISO VG 32 or VG 46. Use phosphate ester or polyol ester fluid.
More informationHigh Pressure, Subplate Mounted Directional Control Valves
ENGINEERING SECIFICIONS High ressure, Subplate Mounted Directional Control Valves MODEL H03 5 gpm (19 L/min) nominal 10 000 psi (700 bar) H03 valves are rated for 5 gpm (19 L/min) nominal flow at pressures
More informationProportional pressure reducing valve of 3-way design
Courtesy of CM/Flodyne/Hydradyne Motion Control Hydraulic neumatic Electrical Mechanical (800) 426-5480 www.cmafh.com Electric Drives and Controls Hydraulics Linear Motion and ssembly echnologies neumatics
More informationVRN2-10. Functional Description HA /2008. Pilot Operated Pressure Reducing Valves. Replaces HA /2003
Pilot Operated Pressure Reducing Valves VRN2-0 HA 554 7/2008 Size 0 p max up to 20 bar Q max up to 50 (80) L/min Replaces HA 554 2/200 Screw-in cartridge valve for manifold mounting and stacking assemblies
More informationPump Safety Block Model DBA... / DBAW, Series 1X
ump Safety lock odel D... / DW, Series X Sizes to 6 SI ( bar) 7 G (65 L/min) R 5 88/.95 Replaces:.9 ermits low pressure start-up and by-pass of pump Direct mounting to SE pressure port of pump Light biasing
More informationDirectional Controls
Vickers Directional Controls Pilot Operated Directional Control Valves DG5S4-10**-53 DG4S4-01-50 Air Gap Pilot Valve DG5S4-10**-80 DG4S4-01-60 Wet Armature Pilot Valve DG5S4-10** -90 DG4V-3S-60 Pilot Valve
More informationILD LOCK CYLINDER CHANGE-OUT INSTRUCTIONS REVISION 2_012505
1. TOOLS REQUIRED for ILD LOCK CYLINDER CHANGE-OUT a. 3/16 Hex Allen Wrench b. Phillips Screwdriver c. 1-3/8 Deep Socket or Adjustable Wrench d. Blocks to support ILD 2. LOCK CYLINDER ASSEMBLY REMOVAL,
More informationHigh Pressure, High Flow Rate Modular Valves
High Pressure, High Modular Valves EIC-F-14- MODULR VLVES The modular valves are functional elements with which a hydraulic system can be composed and built easily by stacking them with the mounting bolts.
More informationMEMORY SEAL BALL VALVES MAINTENANCE MANUAL 2 12, Class 150 & 300, Regular Port, Flanged Unibody
MEMORY SEAL BALL VALVES MAINTENANCE MANUAL 2 12, Class 150 & 300, Regular Port, Flanged Unibody I INTRODUCTION These rugged, versatile, high performance, regular port, ball valves meet all requirements
More informationIndustrial Hydraulic Valves. Directional Control, Pressure Control, Sandwich, Subplates & Manifolds, Accessories. Catalog HY /US
LH Industrial Hydraulic Valves Directional Control, ressure Control, Sandwich, Subplates & Manifolds, ccessories Catalog HY14-2500/US Industrial Hydraulic Valves LH WRNING USER RESONSIILIY FILURE OR IMROER
More information8.2 Service of the Actuator HYC4018M Series
8.2 Service of the ctuator HY4018M Series 8.2.1 echnical Data HY4018M03-F/-R, HY4018M04-F/-R, HY4018M05-F/-R ctuator, bolted to manifold. Valve pin operation Operation medium Operating pressure ressure
More informationIndustrial Hydraulic Valves. Directional Control, Pressure Control, Sandwich, Subplates & Manifolds, Accessories. Catalog HY /US
Industrial Hydraulic Valves Directional Control, ressure Control, Sandwich, Subplates & Manifolds, ccessories Catalog HY14-2500/US Industrial Hydraulic Valves WRNING USER RESONSIILIY FILURE OR IMROER SELECION
More informationHousings and Miscellaneous Parts
Housings and Miscellaneous Parts Standard and Special Valve Housings, Orifice Disks, Orifice Sizing harts, Pilot Pistons, dapters, djustment Kits and Seal Kits ETON Vickers Screw-in artridge Valves V-VLOV-M001-E1
More informationBar 35 PSI 500. Pressure Drop L/M GPM. Flow
NF D3 O E R I N G N D E C H N I C L D RINGS Maximum Flow... See Chart Maximum Operating ressure (, and orts)... 3 ar ( SI) Maximum ank Line ressure... 13 ar (1 SI) Mounting attern... ISO 441--3-4-, NF-D3
More informationInstallation Instructions TH700-R4 (4L60) Transkit Part No thru 1986 Part No thru 1993 non-electronic models
Installation Instructions TH700-R4 (4L60) Transkit Part No. 70232 1982 thru 1986 Part No. 70233 1987 thru 1993 non-electronic models B&M Racing and Performance Products 2009 Congratulations! You have just
More informationUSA Headquarters. Dynex/Rivett Inc. 770 Capitol Drive Pewaukee, WI U.S.A. Tel: FAX:
DIRECIONL VLVE OERION Directional Valve Features, Selection and Operating Recommendations CONC INFORMION US Headquarters Dynex/Rivett Inc. 770 Capitol Drive ewaukee, WI 3072 U.S.. el: 262-69-2222 FX: 262-69-032
More informationLWCV ACTUATOR ASSEMBLY AND MAINTENANCE INSTRUCTIONS
LWCV ACTUATOR ASSEMBLY AND MAINTENANCE INSTRUCTIONS CANDOC LWCV ACTUATOR MANUAL COPYRIGHT 2009 CANRIG DRILLING TECHNOLOGY LTD. ALL RIGHTS RESERVED Information in this document is subject to change without
More informationDirectional Valves. Pilot Operated Directional Valves. Vickers. Service Data
Service Data Vickers Directional Valves Pilot Operated Directional Valves Eaton Hydraulics, Incorporated 14615 Lone Oak Road Eden Prairie, Minnesota 55344-2287 U.S.A. 5007.04/EN/0799/S DG5V - 8 - S/H -
More information235/245400, , 28N
Models 235/245400, 287000, 28N thru W, 310/312/313700 These carburetors have a fixed high speed main jet with adjustable idle, Fig 183. The different carburetors are identified as LMT 1 and up. The letters
More informationVickers 45. VMQ Series 30 Vane Pumps. Fixed Displacement, For Industrial and Mobile Applications (4.188)
[ (4.188) 49,4 (1.94) /21,8 /.86) 174,7/172,3 (6.88/6.78) 332,9/33,5 (13.11/13.1) "M" is marked if metric port threads No marking if inch port threads AS-568-152 O-ring Vickers 45 65,3 (2.57) 13 (5.1 VMQ
More informationH Low Torque Impact Wrench
SERVICE MANUAL H8508-3 Low Torque Impact Wrench Serial Code AKW Read and understand all of the instructions and safety information in this manual before operating or servicing this tool. Register this
More informationSize 06 (D03) Q max 100 l/min (26.4 GPM) p max 250 bar (4600 PSI) RPE*-06 PRM*-06
Modular Load Sensing System MLS3-06 Size 06 (D03) Q max 00 l/min (26.4 GM) p max 250 bar (4600 SI) ossible Applications riority module riority module 2 ase module Section module REK distributors Section
More informationDrVanos.com Stage II Installation Instructions. Tool rental is available with the purchase of a vanos kit *See website for more info*
DrVanos.com Stage II Installation Instructions Special Tools Needed: Camshaft locking tool TDC Crank pin Sprocket turning tool Tool rental is available with the purchase of a vanos kit *See website for
More information4/3 and 4/2 on-off directional valve elements D8_5 with or (EDD-XZ) without secondary relief valves and with or without LS connections D8_5 (EDD-XZ)
4/3 and 4/2 on-off directional valve elements D8_5 with or (EDD-XZ) without secondary relief valves and with or without LS connections D8_5 (EDD-XZ) RE 18301-12 Edition: 02.2016 Replaces: 07.12 07.2012
More informationCVH103P. Check Valve Series CVH103P. Technical Information. General Description
Catalog HY-351/US Information Cartridge Style Valve. For additional information see Tips on pages 1-4. Valve Series H13P Spherical poppet for low leakage D -Ring eliminates back-up rings Dual sense paths
More informationOpen center control block in mono block design MO-16, 22, 32
Open center control block in mono block design MO-,, 3 RE 35 Edition: 0.0 Replaces: 0.003 Sizes,, 3 Series X Maximum working pressure on the pump side 350 bar on the consumer side 0 bar Maximum flow MO-:
More informationSolenoid Operated Directional Valves
We have made it easy for you to find a PDF Ebooks without any digging. And by having access to our ebooks online or by storing it on your computer, you have convenient answers with solenoid operated directional
More information4/2 Directional valve elements with or without secondary relief valves, with or without LS connections, and with 2/2 solenoid cartridge valve
4/2 Directional valve elements with or without secondary relief valves, with or without LS connections, and with 2/2 solenoid cartridge valve RE 183-54/7.12 Replaces: 1.9 1/8 8_58 (EDZ-VEI) Size 4 Series
More information