Directional control valves NG6...NG32 D03...D10 6

Transcription

1 Directional control valves NG6...NG32 D03...D10 6

2 DIRECIONL CONROL VLVES 1 Index DO3 (NG6) age 2 to 22 D05 (NG10) age 23 to 42 D07 (NG16) age 43 to 54 D08 (NG25) 3000 SI age 55 to 65 D08 (NG25) 4600 SI age 66 to 77 D10 (NG32) 3000 SI age 78 to 86 ccessories age 87 to 90

3 2 Directional control valve D03 (NG6) Features and enefits n n n n 3 chamber design with additional spool guide for high performance Wet pin solenoid with increased solenoid forces Optimized flow passages result in lower pressure drop Manual override n Solenoid identification per NSI (energize results in pressure to ) n Certified

4 Directional control valve D03 (NG6) 3 Order Guide his order code describes the desired model variances of the DO3 (NG 6) directional control valves. Standard models are assigned a 10-digit number. See pages 4, 5, & W V V WS** S / D 51 SIZE 06 D03 (NG 6, ISO ) SELS V VION SD. DDIIONL INFORMION 09 MNUL USH IN WIH RUER COVER 11 SOOL WIH MEERING NOCHES CONROL YE 1 ELECRICL 2 HYDRULIC ILO 4 MECHNICL (ROLLER) 6 NEUMIC ILO SOLENOID IDENIFICION 51 U.S. SNDRD (U.S. NSI 93.9 SD.) DESIGN SERIES D - SD *E - 24 VDC LED WIRE COILS 7 MNUL LEVER 7 MNUL LEVER (WIH DEEN G **) SOOL CODE *** SEE SOOL CHR (GES 4, 5 & 6) ELECRICL CONNECIONS WS DIN 43650/ISO4400 KL WIRING OX + SEN. LIGHS K WIRING OX KD WIRING OX + QUICK CONN. (NSI 93.55M IN SINGLE SOL. & 5 IN. DOULE. SOL.) KE WIRING OX + QUICK CONN. + SEN. LIGHS KG WIRING OX + QUICK CONN. (SINGLE SOL. 5 IN) KM WIRING OX + QUICK CONN. + SEN. LIGHS (SINGLE SOL. 5 IN) G DEEN CONROL YE 7 ONLY EX FLME ROOF SOLENOID VOLGES C DC 115/60 012/00 230/60 024/00 Series D Dual Freq. 096/00 SOLENOID OIONS OMI: If standard (manual override) C COVERED USH IN * QUICK CONNEC FOR E SERIES IS MINI CONNECOR (G 89) roduct Literature Disclaimer SECIFICIONS ND/OR DIMENSIONS RE SUJEC O CHNGE WIHOU RIOR NOICE. LESE CONSUL FCORY.

5 4 Directional control valve D03 (NG6) art Numbers Standard types are assigned a 10-digit part number. Describe unassigned valve combinations with the alpha-numeric order code. K KD KE KG KL KM WS WS SOOL SYMOLS RNSIION 110/ / / / / / / VDC. NO. 220/ / / / / / / VDC. 024/00 024/00 024/00 024/00 96 VDC. Z069 Z201 Z267 Z135 Z003 Z Z102 Z234 Z300 Z168 Z036 Z430 Z Z K WIRING OX KD WIRING OX + QUICK CONNEC ( 3 IN SING. & 5 IN DL. SOL.) KE WIRING OX + QUICK CONNEC + SENINEL LIGHS KG WIRING OX + QUICK CONNEC (SINGLE SOLENOID 5 IN) KL WIRING OX + SENINEL LIGHS KM WIRING OX + QUICK CONNEC + SENINEL LIGHS (SINGLE SOL. 5 IN) WS LUG CONNECER (DIN / ISO 4400) D11 SOOL WIH MEERING NOCHES* Z070 Z202 Z268 Z136 Z004 Z Z103 Z235 Z301 Z169 Z037 Z431 Z511 Z477 Z463 Z * Z521 Z071 Z203 Z269 Z137 Z005 Z Z104 Z236 Z302 Z170 Z038 Z432 Z531 Z * Z464 Z072 Z204 Z270 Z138 Z006 Z Z105 Z497 Z237 Z303 Z478 Z171 Z516 Z039 Z * Z465 Z073 Z205 Z271 Z139 Z007 Z Z106 Z238 Z304 Z172 Z040 Z434 Z074 Z206 Z272 Z140 Z008 Z Z107 Z239 Z305 Z173 Z041 Z435 Z075 Z207 Z273 Z333 Z141 Z365 Z009 Z Z108 Z240 Z306 Z349 Z174 Z381 Z042 Z436 Z508 Z491 Z076 Z208 Z274 Z334 Z142 Z366 Z010 Z * Z109 Z241 Z307 Z350 Z175 Z382 Z043 Z437 Z487 Z077 Z209 Z275 Z335 Z143 Z367 Z011 Z Z110 Z242 Z308 Z351 Z176 Z383 Z044 Z438 Z480 Z078 Z210 Z276 Z336 Z144 Z368 Z012 Z Z111 Z243 Z309 Z352 Z177 Z384 Z045 Z439 Z079 Z211 Z277 Z337 Z145 Z369 Z013 Z Z112 Z244 Z310 Z353 Z178 Z385 Z046 Z * Z467 * Metering notches

6 Directional control valve D03 (NG6) 5 K KD KE KG KL KM WS WS SOOL SYMOLS RNSIION 110/ / / / / / / VDC. NO. 220/ / / / / / / VDC. 024/00 024/00 96 VDC. Z080 Z212 Z278 Z146 Z014 Z Z113 Z245 Z311 Z179 Z047 Z441 Z479 Z * Z468 Z081 Z213 Z279 Z147 Z015 Z Z114 Z246 Z312 Z180 Z048 Z442 Z481 Z518 Z082 Z214 Z280 Z338 Z148 Z370 Z016 Z Z115 Z247 Z313 Z354 Z181 Z386 Z049 Z443 Z525 Z525 Z083 Z215 Z281 Z149 Z017 Z Z116 Z248 Z314 Z182 Z050 Z444 Z084 Z216 Z282 Z339 Z150 Z371 Z018 Z Z117 Z249 Z315 Z355 Z183 Z387 Z051 Z Z474 Z475 Z496 Z085 Z217 Z283 Z340 Z151 Z372 Z019 Z Z118 Z250 Z316 Z356 Z184 Z388 Z052 Z446 Z086 Z218 Z284 Z341 Z152 Z373 Z020 Z Z119 Z251 Z317 Z357 Z185 Z389 Z053 Z447 Z087 Z219 Z285 Z342 Z153 Z374 Z021 Z Z120 Z252 Z318 Z358 Z186 Z390 Z054 Z448 Z488 Z546 Z Z493 Z088 Z220 Z286 Z154 Z022 Z Z121 Z253 Z319 Z187 Z055 Z449 Z089 Z221 Z287 Z155 Z023 Z Z122 Z254 Z320 Z188 Z056 Z450 Z090 Z222 Z288 Z156 Z024 Z Z123 Z255 Z321 Z189 Z057 Z451 Z091 Z223 Z289 Z343 Z157 Z375 Z025 Z Z124 Z256 Z322 Z359 Z190 Z391 Z058 Z452 Z092 Z224 Z290 Z158 Z026 Z Z125 Z257 Z323 Z191 Z059 Z453 Z093 Z225 Z291 Z344 Z159 Z376 Z027 Z Z126 Z258 Z324 Z360 Z192 Z392 Z060 Z454 Z094 Z226 Z292 Z345 Z160 Z377 Z028 Z Z127 Z259 Z325 Z361 Z193 Z393 Z061 Z455 Z095 Z227 Z293 Z346 Z161 Z378 Z029 Z Z128 Z260 Z326 Z362 Z194 Z394 Z062 Z456 Z096 Z228 Z294 Z162 Z030 Z Z129 Z261 Z327 Z195 Z063 Z457 Z097 Z229 Z295 Z347 Z163 Z379 Z031 Z Z130 Z262 Z328 Z363 Z196 Z395 Z064 Z458 * Metering notches

7 6 Directional control valve D03 (NG6) art Numbers (continued) K KD KE KG KL KM WS WS SOOL SYMOLS RNSIION 110/ / / / / / / VDC. NO. 220/ / / / / / / VDC. 96 VDC. Z472 Z473 Z Z489 ressure port leakage Z098 Z230 Z296 Z164 Z032 Z bleeds to tank in the Z131 Z263 Z329 Z197 Z065 Z459 center position Z099 Z231 Z297 Z165 Z033 Z Z132 Z264 Z330 Z198 Z066 Z460 Z100 Z232 Z298 Z348 Z166 Z380 Z034 Z Z133 Z265 Z331 Z364 Z199 Z396 Z067 Z Z SOOL NO. SYMOLS RNSIION Z365 Z Z379 *Z372 Z366 Z Z380 *Z373 Z367 Z Z382 *Z374 Z368 Z Z384 *Z375 Z Z541 Z333 Z386 *Z544 Z358 Z334 Z369 Z Z388 *Z361 *Z Z335 Z370 Z Z359 *Z378 Z Z391 *With 7/16-20 orts (SE #4)

8 Directional control valve D03 (NG6) 7 Weights DC C Ex. 3.3 lbs 3.1 lbs 5.1 lbs 1.5 kg 1.4 kg 2.3 kg 3.3 lbs 1.5 kg DC C Ex. 4.2 lbs 3.8 lbs 8.8 lbs 1.9 kg 1.7 kg 4.0 kg 2.9 lbs 1.3 kg 2.9 lbs 1.3 kg 3.3 lbs 1.5 kg 3.3 lbs 1.5 kg 4.4 lbs 2.0 kg

9 8 Directional control valve D03 (NG6) Characteristics General Design Spool valve (three chamber system) Mounting type Subplate, DO3 (NG 6) ISO 4401 Mounting osition mbient temperature Seals as desired (Horizontal preferred) 4 to 120 F (-20 to 50 C) Viton CS Certified File Number LR Hydraulic Fluid Viscosity Fluid temperature remium quality petroleum and water glycol fluids. Refer to the following bulletins for recommendations: S106 - etroleum Fluids S107 - Fire Resistant Fluids Consult factory for use of water in oil emulsions, high water content and synthentic fluids. Mineral-oil based hydraulic-fluids (DIN/ISO) others on request SUS ( cst) 4 to 175 F ( 20 to 80 C) Filtration Contamination class 19/16, according to ISO 4406 to be realized with filter ß25=75 Direction of flow Operating pressure Rated flow s shown on symbol ort,, : 4600 SI (315 bar) ort * : 2300 SI (160 bar) See p/q-curves Maximum flow Up to 23 GM (90 L) see operating limits * For control type 1 EX 1500 SI (100 bar) Electric Duty factor 100% Solenoid identification Enclosure type Meets NSI (R 1988) Standards *I 65 to IEC and DIN (DIN Connectors) Insulation class C VDE 5 Voltage and frequency See table on page 88 C-solenoids 230/60 can be used with 220/50 and 115/60 can be used with 110/50 voltage supply Voltage tolerance UNOM±10% ower rating DC 33W C (115/60) In Rush: ~ 1.5 Holding: ~ 0.54 Response time** DC Switch-on: 20 to 60 ms Switch-off: 10 to 60 ms C Switch-on: 10 to 25 ms Switch-off: 50 to 65 ms Switching frequency max. 1800/h ower supply lug connector to DIN Wiring ox 5 & 3 in QC ISO 4400 w/ Lead Wires per NSI 93.55M *Note: I 65 rotected against low pressure water jets from all direction Dust tight ** Response time measured from the switching signal to opening of control edge.

10 Directional control valve D03 (NG6) 9 erformance Characteristics Valve ressure vs. Flow erformances Curve Reference Numbers Spool Curve Numbers Number RESSURE SI(R) 360(25) RESSURE vs. FLOW CURVES Spool Number (20) 215(15) 146(10) 70(5) 0(0) (0) 4(15) 8(30) 12(45) 16(60) 20(75) 24(90) FLOW GM(L/M) Viscosity = 164 SUS (35 Centistokes)

11 10 Directional control valve D03 (NG6) erformance Characteristics SERIES E DC Solenoids Curve Reference Numbers Spool Number () Curve Numbers () MLFUNCION CURVES 3600 (250) Switch-on 1 RESSURE SI (R) 2900 (200) 2200 (150) 1450 (100) (50) (10) 5 (20) 8 (30) 10 (40) 13 (50) Flow GM (L/min) 3600 (250) Switch-off 1 RESSURE SI (R) 2900 (200) 2200 (150) 1450 (100) (50) (10) 5 (20) 8 (30) 10 (40) 13 (50) Flow GM (L/min) Operating limits he curves refer to applications with symmetrical flow. In the case of asymmetric flow (e.g. one port not used) reduced values may result.

12 Directional control valve D03 (NG6) 11 erformance Characteristics DC-Solenoids Curve Reference Numbers Spool Curve Numbers Number () () RESSURE SI (R) 4300 (300) 2900 (200) 1450 (100) RESSURE SI (R) 0 (0) 0(0) 8(30) 16(60) 24(90) 4300 (300) () Switch On () Switch Off MLFUNCION CURVES FLOW GM (L/M) (200) (100) 0 (0) 0(0) 8(30) 16(60) 24(90) FLOW GM (L/M) Operating limits he curves refer to applications with symmetrical flow. In the case of asymmetric flow (e.g. one port not used) reduced values may result.

13 12 Directional control valve D03 (NG6) erformance Characteristics C-Solenoids Curve Reference Numbers Spool Curve Numbers Number RESSURE SI (R) 4300 (300) 2900 (200) 1450 (100) 0 (0) MLFUNCION CURVES 6 0(0) 8(30) 16(60) 24(90) FLOW GM (L/M) Operating limits he curves refer to applications with symmetrical flow. In the case of asymmetric flow (e.g. one port not used) reduced values may result.

14 Directional control valve D03 (NG6) 13 Valve With DC Solenoid DIN Seal Kit Inches (Millimeters) Clearance needed to remove connector.47 (12.0) 3.73 (94.7) MNUL USH IN.94 (24.0).87 (22.0) Solenoids can be rotated ± (37.2) 2.93 (74.4) ORQUE 5.0 lbft (7.0 Nm) 2.56 (65.0) Note: Min. depth of fastener engagement is based on 1-1/2 times bolt diameter for ferrous subplates or manifolds and 2-1/2 times for nonferrous. Note: Clearance to remove coil 2.93 (74.4) With Rubber Cover (30) Covered O RING (4) 9.25mm x 1.78mm (46.0) 1.22 (31.0) 4 x ø.21 (4 x ø5.3) 1.59 (40.5).53 (13.5) 1.28 (32.5) 5.93 Single Solenoid (150.6) 8.43 (214.1) Note: Mounting surface should comply with NF 3.5 IM RI-1984 & NSI 93.7M specifications.

15 14 Directional control valve D03 (NG6) Valve With C Solenoid DIN Seal Kit Inches (Millimeters) Clearance needed to remove connector.47 (12.0) MNUL USH IN 3.70 (94.0).94 (24.0).87 (22.0) Solenoids can be rotated ± (66.9) ORQUE 5.0 lbft (7.0 Nm) 2.56 (65.0) Note: Min. depth of fastener engagement is based on 1-1/2 times bolt diameter for ferrous subplates or manifolds and 2-1/2 times for nonferrous. Note: Clearance to remove coil 2.63 (66.9) 1.46 (37.2) With Rubber Cover (30) Covered O RING (4) 9.25mm x 1.78mm (46.0) 1.22 (31.0) 4 x ø.21 (4 x ø5.3) 1.59 (40.5).53 (13.5) 1.28 (32.5) 5.63 Single Solenoid (143.1) 7.82 (198.7) Note: Mounting surface should comply with NF 3.5 IM RI-1984 & NSI 93.7M specifications.

16 Directional control valve D03 (NG6) 15 Valve with C/DC Solenoid and Wiring Seal Kit Inches (Millimeters) OIONL SENINEL LIGHS HREDED CONN. 1/2 N * OIONL QUICK CONNEC.62 (15.9) * SEE CCESSORY SECION FOR DEILS MNUL USH IN 3.74 (95.0) 2.81 (71.5).94 (24.0).87 (22.0) 1.46 (37.2) 2.63 (66.9) ORQUE 5.0 lbft (7.0 Nm) 2.56 (65.0) With Rubber Cover Note: Min. depth of fastener engagement is based on 1-1/2 times bolt diameter for ferrous subplates or manifolds and 2-1/2 times for nonferrous. Note: rad Harrison connector installed on cylinder port side on double solenoid valves and on solenoid side on single solenoid valves. Note: Clearance to remove coil 2.63 (66.9).1.18 (30) Covered O RING (4) 9.25mm x 1.78mm (46.0) 1.22 (31.0) 4 x ø.21 (4 x ø5.3) 1.59 (40.5).53 (13.5) 1.28 (32.5) 5.63 Single Solenoid (143.1) 7.82 (198.7) Note: Mounting surface should comply with NF 3.5 IM RI-1984 & NSI 93.7M specifications.

17 16 Directional control valve D03 (NG6) Flame roof Solenoid Conversion from the standard solenoid to the flame-proof version is not possible. he solenoid is mounted on the valve body (optional version) with 4 socket-head cap screws. Note: Not CS pproved Consult factory for application support and part numbers. Specifications ype of enclosure I 65 to IEC and DIN VDE 0470 Flame proof ype of protection (Ex) sg4 mbient temperature 4 to 122 F ( 20 to 50 C) Cyclic duration factor ED 100% ower rating 11 W Voltage tolerance ±10% Fuses Response according to ISO 6403 Switch on/off time 40/120 ms ower supply ower gland G 16 DIN for cabel ø mm Switching frequency max. 18,000/h ressure in port (Solenoid armature) max SI (100 bar) Inches (Millimeters) 8.78 (223) (359) 2.28 (58) 1.22 (31) 1.28 (32.5) 1.81 (46) 1.59 (40.5).53 (13.5) 4.33 (110).94 (24) 1.93 (49) 3.50 (89) 2.56 (65) 9.25 x 1.78

18 Directional control valve D03 (NG6) 17 neumatic Control 150 (10) p = f (p ) St ilot pressure S is a function of tank line pressure 120 (8) 90 (6) St p 60 (4) 40 (2) 0 (0) (0) (40) (80) (120) (160) (200) p SI (R) Specifications Control pressure 30 SI (2bar) min,, 150 SI (10 bar) max. ilot volume per valve side.12 in 3 (2cm 3 ) Response according to ISO 6403 Switch on 20 to 200 ms Switch off 30 to 300 ms Dependent on pilot pressure and line length Hydraulic Control 1500 (100) p = f (p ) St ilot pressure S is a function of tank line pressure 1300 (80) 900 (60) St p 600 (40) 300 (20) 0 (0) (0) (40) (80) (120) (160) (200) SI (R) p Specifications Control pressure 290 SI ( 20bar) min, p 3000 SI (210 bar) max. ilot volume per valve side.02 in 3 (0.3cm 3 ) Response according to ISO 6403 pst = 700 SI pst = 3000 SI (50 bar) (200 bar) Switch on 50 to 100 ms 15 to 30 ms Switch off 60 to 150 ms 60 to 150 ms Dependent on pilot pressure and line length. When ps > 1500 SI (100 bar), orifice ø 1mm is necessary.

19 18 Directional control valve D03 (NG6) Inches (Millimeters) 2.01 (51.0).94 (24.0).87 (22.0) G 1/4 daptor to #4 SE (53.1) ORQUE 5.0 lbft (7.0 Nm) 2.56 (65.0) O RING (4) 9.25mm x 1.78mm Note: Min. depth of fastener engagement is based on 1-1/2 times bolt diameter for ferrous subplates or manifolds and 2-1/2 times for nonferrous (46.0) 1.22 (31.0) 4 x ø.21 (4 x ø5.3) 1.59 (40.5) 5.09 Single Solenoid (143.1) 6.73 (170.9).53 (13.5) 1.28 (32.5) Note: Mounting surface should comply with NF 3.5 IM RI-1984 & NSI 93.7M 1986 specifications. Kit Numbers for the conversion of solenoid control to hydraulic or pneumatic. Spool ype of Control Number Hydraulic neumatic D D Spool ype of Control Number Hydraulic neumatic

20 Directional control valve D03 (NG6) 19 Directional Control Valve Mechanical Operated 50 (200) F = lbs (N ) 40 (160) FORCE 30 (120) 20 (80) 10 (40) 0 (0) (20) (60) (100) (140) (180) SI (R) p (tank pressure) 5.04 (128) Inches (Millimeters) 1.77 (45).87 (22).39 (10) 1.22 (31) 1.28 (32.5) 1.81 (46) SROKE.35 (9).79 (20).43 (11) 2.46 (62.4) 1.59 (40.5) 1.59 (40.5).47 (12).87 (22).94 (24) 1.93 (49).35 max..51 (13) 1.47 (37.4) ø.21 (5.3) 2.56 (65) 9.25 x 1.78

21 20 Directional control valve D03 (NG6) Directional Control Valve Manual Operated Specifications ctuating force 7.8 lbs. (35 N) ngular movement +_23 Inches (Millimeters) 5.80 (147.3) 1.22 (31) 1.28 (32.5) 1.81 (46) 1.14 (29) 6.30 max. (160) 1.59 (40.5).53 (13.5) 7.36 (187) Lever Knob max. b.23 max. a.87 (22).94 (24) 1.93 (49) 1.73 (43.9) 2.41 (61.2) ø.21 (5.3) 2.56 (65) 9.25 x 1.78

22 Directional control valve D03 (NG6) 21 Subplates, ottom orted.343 Drill hru 2 laces (94.4) Inches (Millimeters).548 (13.9) ottom orted ort art Size in(mm) in(mm) Number 1/4" NF (51.2) (21.0) 3/8" NF (52.8) (19.5) 1/2" NF (54.1) (18.0) #6 SE (52.0) (20.2) #8 SE (54.1) (18.0) (72.1) (54) Note: Max. pressure = 4600 psi (315 R) 4.62 (117.3).359 (9.1) 1.50 (38.1).50 (12.7) (88.6) (61.2) (33.5) (36.1) When a subplate is not used a machined pad must be provided. he mounting surface should comply with NF 3.5.1M R and NSI 93.7M specifications.

23 22 Directional control valve D03 (NG6) Subplates, Side orted Inches (Millimeters) Side orted ort art Size in(mm) Number 1/4" NF (12.0) 3/8" NF (12.0).850 (21.59) 1/2" NF (14.7) #6 SE (12.0) #8 SE (14.7).850 (21.59) Note: Max. pressure = 4600 psi (315 R).343 Drill hru 2 laces (94.13).548 (13.92) 2.84 (72.14) (54.10) 3.59 (9.12) (55.22) (40.87).850 (21.59) 1.50 (38.1) 4.62 (117.35).850 (21.59).5 (12.7) When a subplate is not used a machined pad must be provided. he mounting surface should comply with NF 3.5.1M R and NSI 93.7M specifications.

24 Directional control valve D05 (NG10) 23 Features and enefits n n n n n 5 chamber design with additional spool guide lands for increased performance Retained guide tube design for easy interchange of coils Larger.710 in. (18mm) spool diameter provides lower pressure drop Soft shift feature can be retrofitted in the field Optional manual overrides available n Certified n Solenoid identification per NSI standards (energize results in pressure to )

25 24 Directional control valve D05 (NG10) Order Guide his order code describes the desired model variances of the DO5 (NG 10) directional control valves. Standard models are assigned a 10-digit number. See pages 25, 26, & W V V WS** S / D 51 SIZE 10 D05 (NG 10, ISO ) SELS V VION SD. DDIIONL INFORMION 09 MNUL USH IN WIH RUER COVER 11 SOOL WIH MEERING NOCHES CONROL YE 1 ELECRICL 2 HYDRULIC ILO 4 MECHNICL (ROLLER) 6 NEUMIC ILO 7 MNUL LEVER 7 MNUL LEVER (WIH DEEN G **) SOOL CODE *** SEE SOOL CHR (GES 25, 26, & 27) ELECRICL CONNECIONS WS DIN 43650/ISO4401 KL WIRING OX + SEN. LIGHS K WIRING OX KD WIRING OX + QUICK CONN. (NSI 93.55M IN SINGLE SOL. & 5 IN. DOULE. SOL.) KE WIRING OX + QUICK CONN. + SEN. LIGHS KG WIRING OX + QUICK CONN. (SINGLE SOL. 5 IN) KM WIRING OX + QUICK CONN. + SEN. LIGHS (SINGLE SOL. 5 IN) G DEEN CONROL YE 7 ONLY EX FLME ROOF SOLENOID VOLGES C DC 115/60 012/00 230/60 024/00 Series D Dual Freq. 096/00 SOLENOID IDENIFICION 51 U.S. SNDRD (NSI ) DESIGN SERIES (GENERION) D - SD *E - 24VDC LED WIRE COILS SOLENOID OIONS OMI: If standard (manual override) C COVERED USH IN * QUICK CONNEC FOR E SERIES IS MINI CONNECOR (G 89) roduct Literature Disclaimer SECIFICIONS ND/OR DIMENSIONS RE SUJEC O CHNGE WIHOU RIOR NOICE. LESE CONSUL FCORY.

26 Directional control valve D05 (NG10) 25 art Numbers Standard types are assigned a 10-digit part number. Describe unassigned valve combinations with the alpha-numeric order code. K KD KE KG KL KM WS WS --D11 SOOL SYMOLS RNSIION 110/ / / / / / / VDC. 12 VDC. NO. 220/ / / / / / / VDC. 24 VDC. 024/00 024/00 024/00 96 VDC. 96 VDC. Z069 Z201 Z267 Z135 Z003 Z397 Z Z102 Z234 Z300 Z168 Z036 Z430 Z467 Z484** Z070 Z202 Z268 Z136 Z004 Z398 Z Z103 Z235 Z301 Z169 Z037 Z431 Z468 Z490 Z485** Z071 Z203 Z269 Z137 Z005 Z * Z104 Z236 Z302 Z170 Z038 Z432 Z526 Z072 Z204 Z270 Z138 Z006 Z Z105 Z237 Z303 Z171 Z039 Z433 Z498 Z529 Z491 Z472 Z073 Z205 Z271 Z139 Z007 Z Z106 Z238 Z304 Z172 Z040 Z434 Z074 Z206 Z272 Z140 Z008 Z Z107 Z239 Z305 Z173 Z041 Z435 Z075 Z207 Z273 Z333 Z141 Z365 Z009 Z Z108 Z240 Z306 Z349 Z174 Z381 Z042 Z436 Z508 Z076 Z208 Z274 Z334 Z142 Z366 Z010 Z404 Z Z109 Z241 Z307 Z350 Z175 Z382 Z043 Z437 Z469 Z481** Z077 Z209 Z275 Z335 Z143 Z367 Z011 Z Z110 Z242 Z308 Z351 Z176 Z383 Z044 Z438 Z513 Z493 Z471 Z078 Z210 Z276 Z336 Z144 Z368 Z012 Z * Z111 Z243 Z309 Z352 Z177 Z384 Z045 Z439 Z079 Z211 Z277 Z337 Z145 Z369 Z013 Z Z112 Z244 Z310 Z353 Z178 Z385 Z046 Z440 Z080 Z212 Z278 Z146 Z014 Z408 Z Z113 Z245 Z311 Z179 Z047 Z441 Z470 Z492 Z483** Z K WIRING OX KD WIRING OX + QUICK CONNEC (RD HRR. 3 IN SING. & 5 IN DL. SOL.) KE WIRING OX + QUICK CONNEC + SENINEL LIGHS KG WIRING OX + QUICK CONNEC (SINGLE SOLENOID 5 IN) KL WIRING OX + SENINEL LIGHS KM WIRING OX + QUICK CONNEC + SENINEL LIGHS (SINGLE SOL. 5 IN) WS LUG CONNECER (DIN / ISO 4401) D11 SOOL WIH MEERING NOCHES Z081 Z213 Z279 Z147 Z015 Z Z114 Z246 Z312 Z180 Z048 Z442 Z528 Z494 Z525** Z082 Z214 Z280 Z338 Z148 Z370 Z016 Z Z115 Z247 Z313 Z354 Z181 Z386 Z049 Z443 Z494 * Metering notches Std. ** Soft shift with 1 mm orifice Z480** Z489 Z482**

27 26 Directional control valve D05 (NG10) K KD KE KG KL KM WS WS --D11 SOOL 110/ / / / / / / VDC. 12 VDC. NO. SYMOLS RNSIION 220/ / / / / / / VDC. 24 VDC. 96 VDC. 96 VDC. Z083 Z215 Z281 Z149 Z017 Z Z116 Z248 Z314 Z182 Z050 Z444 Z084 Z216 Z282 Z339 Z150 Z371 Z018 Z Z117 Z249 Z315 Z355 Z183 Z387 Z051 Z Z488 Z085 Z217 Z283 Z340 Z151 Z372 Z019 Z Z118 Z250 Z316 Z356 Z184 Z388 Z052 Z446 Z086 Z218 Z284 Z341 Z152 Z373 Z020 Z Z119 Z251 Z317 Z357 Z185 Z389 Z053 Z447 Z087 Z219 Z285 Z342 Z153 Z374 Z021 Z Z120 Z252 Z318 Z358 Z186 Z390 Z054 Z448 Z088 Z220 Z286 Z154 Z022 Z Z121 Z253 Z319 Z187 Z055 Z449 Z089 Z221 Z287 Z155 Z023 Z Z122 Z254 Z320 Z188 Z056 Z450 Z090 Z222 Z288 Z156 Z024 Z Z123 Z255 Z321 Z189 Z057 Z451 Z091 Z223 Z289 Z343 Z157 Z375 Z025 Z Z124 Z256 Z322 Z359 Z190 Z391 Z058 Z452 Z092 Z224 Z290 Z158 Z026 Z Z125 Z257 Z323 Z191 Z059 Z453 Z093 Z225 Z291 Z344 Z159 Z376 Z027 Z Z126 Z258 Z324 Z360 Z192 Z392 Z060 Z454 Z094 Z226 Z292 Z345 Z160 Z377 Z028 Z Z127 Z259 Z325 Z361 Z193 Z393 Z061 Z455 Z095 Z227 Z293 Z346 Z161 Z378 Z029 Z Z128 Z260 Z326 Z362 Z194 Z394 Z062 Z456 Z096 Z228 Z294 Z162 Z030 Z Z129 Z261 Z327 Z195 Z063 Z457 Z097 Z229 Z295 Z347 Z163 Z379 Z031 Z Z130 Z262 Z328 Z363 Z196 Z395 Z064 Z458 ressure port leakage Z098 Z230 Z296 Z164 Z032 Z bleeds to tank in the Z131 Z263 Z329 Z197 Z065 Z459 center position Z099 Z231 Z297 Z165 Z033 Z Z132 Z264 Z330 Z198 Z066 Z460 Z100 Z232 Z298 Z348 Z166 Z380 Z034 Z Z133 Z265 Z331 Z364 Z199 Z396 Z067 Z461 Z101 Z233 Z299 Z167 Z035 Z Z134 Z266 Z332 Z200 Z068 Z462 Z487

28 Directional control valve D05 (NG10) Z SOOL NO. SYMOLS RNSIION Z Z857 Z905 Z Z853 Z906 Z Z907 Z929 Z Z Z876 Z Z859 Z877 Z Z Z858 Z883 Z Z863 Weights DC 13.4 lbs 6.1 kg C 12.3 lbs 5.6 kg Ex lbs 7.2 kg DC 17.0 lbs 7.7 kg C 14.8 lbs 6.7 kg Ex lbs 11.7 kg 8.8 lbs 4.0 kg 11.7 lbs 5.3 kg 6.6 lbs 3.0 kg 7.5 lbs 3.4 kg

29 28 Directional control valve D05 (NG10) Function Five chamber spool type valve with wet pin solenoid he coil is rotateable and can be mounted in 3 different positions (3 x 90 offset). Caution: Exchange of DC coil for C coil not possible. ypical Code: Soft Shift djustment Data orque = 3.5 ft./lbs. When retrofitting, the screw plug is replaced by a throttle screw. Make sure that the internal cavity of the valve is completely filled with oil, since this is a prerequisite for the proper operation of the soft shift adjustment. ll air must be removed from this cavity by bleeding. o do this remove throttle screw and apply a max of 100 SI to valve tank port. **Caution: For use with DC solenoids only. Not to be used with C solenoids. If C applications are required, please use valves with 96 VDC solenoids and rectifier package For best performance use spools with open cross over or throttled spool W V V W S 0 9 6** / 0 0 D 5 1 * 11 HROLE SOOL Soft Shift djustment* * Note: hrottle screw must be ordered separately. See G 88 for details.

30 Directional control valve D05 (NG10) 29 Characteristics General Design Spool valve (five chamber system) Mounting type Subplate, DO5 (NG 10) ISO 4401 Mounting osition mbient temperature Seals as desired (Horizontal preferred) 4 to 120 F (-20 to 50 C) Viton CS Certified File Number LR Hydraulic Fluid Viscosity Fluid temperature remium quality petroleum and water glycol fluids. Refer to the following bulletins for recommendations: S106 - etroleum Fluids S107 - Fire Resistant Fluids Consult factory for use of water in oil emulsions, high water content and synthentic fluids. Mineral-oil based hydraulic-fluids (DIN/ISO) others on request SUS ( cst) 4 to 175 F ( 20 to 80 C) Filtration Contamination class 19/16, according to ISO 4406 to be realized with filter ß25=75 Direction of flow Operating pressure Rated flow Maximum flow * For control type s shown on symbol ort,, : 4600 SI (315 bar) ort * : 2300 SI (160 bar) See p/q-curves Up to 34 GM (130 L) see operating limits Electric Duty factor 100% Solenoid identification Meets NSI (R 1988) Standards Enclosure type *I 65 to IEC and DIN Insulation class C VDE 5 Voltage and frequency See table on page 88 C-solenoids 230/60 can be used with 220/50 and 115/60 can be used with 110/50 voltage supply Voltage tolerance UNOM±10% ower rating DC 42W C In Rush: ~3.5 Holding: ~1.14 Response time DC Switch-on:** 65 to 100 ms Switch-off:** 30 to 80 ms C Switch-on:** 10 to 25 ms Switch-off:** 50 to 65 ms Switching frequency max. 1800/h ower supply lug connector to DIN Wiring box 5 & 3 pin Q.C. ISO 4400 w/lead wires per NSI 93.55M *Note: I 65 rotected against low pressure water jets from all direction Dust tight ** Valves without soft shift adjustment, measured from the switching signal to opening of control edge.

31 30 Directional control valve D05 (NG10) erformance Characteristics Valve ressure vs. Flow erformances Curve Reference Numbers Spool Curve Numbers Number Spool Number RESSURE SI(R) 290(20) 260(18) 230(16) 200(14) 175(12) 145(10) 116(8) 87(6) 58(4) 29(2) 0(0) RESSURE vs. FLOW CURVES 0(0) 5.5(20) 10.5(40) 16.0(60) 21.0(80) 26.0(100) 32.0(120) 34.0(130) FLOW GM(L/M) Note: Viscosity = 164 SUS (35 Centistokes)

32 Directional control valve D05 (NG10) 31 erformance Characteristics DC-Solenoids Curve Reference Numbers Spool Curve Numbers Number RESSURE SI(R) 4600(315) 4300(300) 2900(200) 1450(100) MLFUNCION CURVES 8 0(0) 0(0) 5.5(20) 10.5(40) 16.0(60) 21.0(80) 26.0(100) 32.0(120) 34.0(130) FLOW GM(L/M) Operating limits he curves refer to applications with symmetrical flow. In the case of asymmetric flow (e.g. one port not used) reduced values may result

33 32 Directional control valve D05 (NG10) erformance Characteristics C-Solenoids Curve Reference Numbers Spool Curve Numbers Number RESSURE SI(R) 4600(315) 4300(300) 2900(200) 1450(100) MLFUNCION CURVES 0(0) 6 0(0) 5.5(20) 10.5(40) 16.0(60) 21.0(80) 26.0(100) 32.0(120) 34.0(130) FLOW GM(L/M) Operating limits he curves refer to applications with symmetrical flow. In the case of asymmetric flow (e.g. one port not used) reduced values may result

34 Directional control valve D05 (NG10) 33 Valve With DC Solenoid DIN Seal Kit Inches (Millimeters) Clearance needed to remove connector.47 (12) Manual ush in 4.65 (118) 1.53 (38.9) 1.18 * (30) 8.43 Single Solenoid (214).47 (12) 5.12 (130) (313) orque olts (4) 100 in. lbs. (11 +3 Nm) 1.37 (35) 2.75 (70) orque 70 in. lbs. (8 Nm) O Ring (5) 12 mm x 2 mm (8) Optional manual push pins 1.10 (28) Covered *olt length change from series. Note: Min. depth of fastener engagement is based on 1 1/2 times bolt dia. for ferrous subplates or manifolds and 2 1/2 times for nonferrous. Note: Clearance to remove coil 3.66 (93) With rubber cover Note: Mounting surface should comply with NF 3.51M R NSI 93.7M-1986 specifications.

35 34 Directional control valve D05 (NG10) Valve With C Solenoid DIN Seal Kit Inches (Millimeters) Clearance needed to remove connector.47 (12) Manual ush in 4.60 (117) 1.53 (38.9) 1.18 * (30) 7.36 Single Solenoid (187).47 (12) 4.06 (103) (259) orque olts (4) 100 in. lbs. (11 +3 Nm) 1.37 (35) 2.75 (70) orque 70 in. lbs. (8 Nm) O Ring (5) 12 mm x 2 mm Optional manual push pins.31 (8) Covered *olt length change from series. Note: Min. depth of fastener engagement is based on 1 1/2 times bolt dia. for ferrous subplates or manifolds and 2 1/2 times for nonferrous. Note: Clearance to remove coil 2.75 (70) 1.10 (28) With rubber cover Note: Mounting surface should comply with NF 3.51M R NSI 93.7M-1986 specifications.

36 Directional control valve D05 (NG10) 35 Valve With C/DC Solenoid nd Wiring Seal Kit Inches (Millimeters) 2.53 (64.2) Optional sentinel lites hreaded conn. 1/2 N Manual ush in 5.41 (137.5) 4.37 (111.0) 1.53 (38.9) Solenoid 1.18 * (30) Solenoid 7.33 Single Solenoid (186.3).47 (12.0) 4.06 (103.21) (260.42) orque olts (4) 100 in. lbs. (11 +3 Nm) 1.37 (35.0) 2.75 (70) orque 70 in. lbs. (8 Nm) Optional manual push pins O Ring (5) 12 mm x 2 mm *olt length change from series..31 (8) 1.10 (28) Covered Note: Min. depth of fastener engagement is based on 1 1/2 times bolt dia. for ferrous subplates or manifolds and 2 1/2 times for nonferrous. Note: rad Harrison connector installed on cylinder port side on double solenoid valves and on solenoid side on single solenoid valves. (See age 79 for details.) With rubber cover Note: Clearance to remove coil 2.75 (70) Note: Mounting surface should comply with NF 3.51M R NSI 93.7M-1986 specifications.

37 36 Directional control valve D05 (NG10) Flame roof Solenoid Not CS pproved. Consult factory for application support and part numbers..c. Solenoid D.C. Solenoid 110/50 024/00 220/50 110/00 190/00 Specifications ype of enclosure mbient temperature Cyclic duration factor ED 100% ower rating I 65 to IEC and DIN ype of protection (Ex) sg4 4 to 110 F ( 20 to 40 C) 20 W Insulation clas C VDE Voltage tolerance ±10% Switch on/off time 100/40 ms ower supply ower gland G 16 DIN Switching frequency max. 8000/h ressure in port max SI (70 bar) 7.00 (178) 3.66 (93).83 (21) 2.76 (70) Ground terminal.57 +_ 0,15 (14,5) +_.69 0,2 (17,6).39 (10 ) 2.76 Ø(70).24 Ø(6) 1.26 Ø(32).99 (25,2) 1.52 (38,1) 1.30 (32.5) 2.69 (68,2) 3.98 (101) 3.13 (79.4) 0, (125) 2.31 (58,7) 2.76 (70) Emergency manual control M5

38 Directional control valve D05 (NG10) 37 Hydraulic Control erformance Characteristics ilot pressure st is a function of tank line ressure t st SI (ar) 580(40) 430(30) 280(20) 145(10) 0(0) 0(0) 580(40) 1160(80) 1750(120) 2300(160) 2 SI (ar) dapter to #4 SE Seal Kit (54) Inches (Millimeters) 2.76 (70) 1.61 (41) 1.81 (46).47 (12).95 (24) orque 100 in. lbs. G 1/4 iston.47 in (12 mm) Dia. orque 450 in. lbs. orque 310 in. lbs (81) 1.53 (38.9) 1.18 (30).26 Ø(6.6) (12)x(2) 2.32 (59) 4.02 (102) 8.62 (219) dapter to #4 SE (.928) ype of control 2 hydraulic ilot pressure (st) 200 SI (14 bar) min x tank pressure 3600 SI (250 bar) max. ilot volume per valve side.03 in 3 (0.4 cm 3 ) Response times p c = 725 SI (50 bar) p c = 2900 SI (200 bar) Switch-on 50 to 100 ms 15 to 30 ms Switch-off 60 to 150 ms 60 to 150 ms Dependent on pilot pressure and line length Conversion Kit # * Except 020 Spool *SE ort

39 38 Directional control valve D05 (NG10) neumatic Control erformance Characteristics 6 ilot pressure st is a function of tank line ressure t st SI (ar) 145(10) 131(9) 116(8) 102(7) 87(6) 73(5) 58(4) 44(3) 28(2) 15(1) 0(0) 0(0) 580(40) 1160(80) 1750(120) 2300(160) SI (ar) dapter to #4 SE Seal Kit Inches (Millimeters) 2.13 (54) 2.76 (70) 1.61 (41) 1.81 (46).47 (12).95 (24) orque 100 in. lbs. G 1/4 iston 1.2 in (30 mm) Dia. orque 450 in. lbs. orque 310 in. lbs (81) 1.53 (38.9) 1.18 (30).26 Ø(6.6) (12)x(2) 2.32 (59) 4.02 (102) 8.62 (219) dapter to #4 SE (.928) ype of control 6 pneumatic ilot pressure (st) 35 SI (2,5 bar) min x tank pressure 145 SI (10 bar) max. ilot volume per valve side.125 in 3 (2 cm 3 ) Response time Switch-on 20 to 200 ms Switch-off 80 to 300 ms Dependent on pilot pressure and line length Conversion Kit # * Except 020 Spool *SE ort

40 Directional control valve D05 (NG10) 39 Lever Operated 2.13 (54) 2.00 (50.8).95 (24) 1.47 (37.3).47 (12).53 (13.5) 1.06 (16.7).13 (3.2) 2.75 (70) 1.81 (46) 1.36 (39.7).96 (24.5) 2.31 (58.7) Lever Knob (172) 24 x (80) 2.68 (65.2) 3.23 (82) 3.38 (86) 1.53 (38.9) 1.18 (30) 3.01 (76.5) 2.40 (61) 4.02 (102) 4.80 (122) 12 x (216)

41 40 Directional control valve D05 (NG10) Cam Operated CM NGLE max x M5x20 DIN = Nm 2.13 (54) 2.00 (50.8).13 (3.2) 1.47 (37.3) 1.06 (27).66 (16.7).95 (24) 2.75 (70) 1.81 (46) 1.56 (39.7) 2.31 (58.7).96 (24.5).53 (13.5).47 (12) Y 1.53 (38.9) 1.18 (30) 3.38 (86) 3.23 (82) 3.19 (81) 2.68 (68.2) 12x2 X 1.46 (37) Ø.26 (6.6) 4.02 (102) 6.25 (159) Normal ctuated X.421 (10.7).263 (6.7)

42 Directional control valve D05 (NG10) 41 Subplates, ottom orted (71.42).625 (15.88) 3.44 (87.38).660 (16.76).130 (3.3) (51.89) (53.98) (37.34) (27.0).413 (10.5) Dia. 4 Holes Inches (Millimeters) (28.58).250 (6.35).840 (21.34) (32.51) (46.02) olt Kit Kit art Number -180 valve only Subplate ort Size art Number 1/2" N /4" N SE SE NOE: Max. ressure = 4600 SI (315 ar) Subplate mounting holes (2).344 (87.4) Dia. hru.438 (11.12) 4.34 (110.24) (135.74) Valve Mounting Holes (4) 1/4" 20 unc,.69 (17.5) deep.50 (12.7) 1.81 (45.97) (157.73) (73.03) 4.06 (103.12) (51.56) (30.12) (41.28) (79.38) (117.48) When a subplate is not used a machined pad must be provided. he mounting surface should comply with NF 3.5.1M R NSI 93.7M-1986 specification.

43 42 Directional control valve D05 (NG10) Subplates, Side orted Inches (Millimeters) olt Kit Kit art Number -180 valve only (23.82) Subplate ort Size art Number 1/2" N (15.88).750 (19.05).660 (16.76).130 (3.3) (51.89) (32.54) (53.98) (37.34) (27.0).413 (10.5) Dia. 4 Holes (28.58).250 (6.35) 3/4" N SE SE NOE: Max. ressure = 4600 SI (315 ar) 4.06 (103.12) (71.42) 3.44 (87.38).840 (21.34) (32.51) (46.02) Valve Mounting Holes (4) 1/4" 20 unc,.69 (17.5) deep Subplate mounting holes (2).344 (87.4) Dia. hru.438 (11.12) 4.34 (110.24) (135.74).792 (20.12) (52.4).938 (23.82).50 (12.7) 1.81 (45.97) 6.21 (157.73) When a subplate is not used a machined pad must be provided. he mounting surface should comply with NF 3.5.1M R NSI 93.7M-1986 specification.

44 Directional control valve D07 (NG16) 43 Features and enefits n n n Retained guide tube for easy replacement of coils Solenoid identification per U.S. standard. when solenoid is energized Optional manual overrides available n Certified n n n Dual frequency solenoids (50 or 60 Hertz) hrottling spools are standard ilot pressure valve in port is optional

45 44 Directional control valve D07 (NG16) Order Code his order code describes the desired model variances of the DO7 (NG 16) directional control valves. Standard models are assigned a 10-digit number. See page W V V 3 D 5 1 / SIZE 16 D07 (NG 16) SELS V VION SD. CONROL YE 2 HYDRULIC 3 ELECRICL SOOL CODE REFER O SOOL CHR ON GE MNUL USH IN WIH RUER COVER* 51 SOLENOID IDENIFICION ER U.S. SNDRD WHEN SOLENOID IS ENER- GIZED (NSI 93.9) D DESIGN SERIES D - SD **E - 24VDC LED WIRE COILS SOLENOID OIONS* C COVERED USH IN ILO CHOKES* F FIXED DJUSLE * If these options are not needed, omit them from the code R ILO RESSURE VLVE IN * H DJUSLE SOOL SOS* ILO ND DRIN XY EX. ILO EX. DRIN IN. ILO IN. DRIN Y IN. ILO EX. DRIN X EX. ILO IN. DRIN ** QUICK CONNEC FOR E SERIES IS MINI CONNECOR (G 89) ELECRICL CONNECIONS WS DIN 43650/ISO4400 KL WIRING OX + SEN. LIGHS K WIRING OX KD WIRING OX + QUICK CONN. (NSI 93.55m IN SINGLE SOL. & 5 IN. DOULE. SOL.) KE WIRING OX + QUICK CONN. + SEN. LIGHS KG WIRING OX + QUICK CONN. (SINGLE SOL. 5 IN) KM WIRING OX + QUICK CONN. + SEN. LIGHS (SINGLE SOL. 5 IN) EX FLME ROOF SOLENOID SOLENOID VOLGES C DC 115/60 012/00 230/60 024/00 Series D Dual Frequency roduct Literature Disclaimer SECIFICIONS ND/OR DIMENSIONS RE SUJEC O CHNGE WIHOU RIOR NOICE. LESE CONSUL FCORY.

46 Directional control valve D07 (NG16) 45 art Numbers Standard valves are assigned a 10-digit part number. Describe unassigned valve combinations with the alpha-numeric order code. IN. ILO X EX. ILO IN. DRIN Y EX. DRIN Z K WIRING OX KD WIRING OX + QUICK CONNEC (3 IN SINGLE & 5 IN DOULE SOLENOID) KE WIRING OX + QUICK CONNEC + SENINEL LIGHS KG WIRING OX + QUICK CONNEC (SINGLE SOLENOID 5 IN) KL WIRING OX + SENINEL LIGHS KM WIRING OX + QUICK CONNEC + SENINEL LIGHS (SINGLE SOL. 5 IN) WS LUG CONNECER (DIN / ISO 4400) K KD KE KG KL KM WS WS SOOL SYMOLS RNSIION ILO 110/ / / / / / / VDC. NO. & DRIN 000 XY Z033 Z047 Z059 Z005 Z Y Z104 Z099 XY Z034 Z048 Z060 Z006 Z021 Z035 Z049 Z061 Z007 Z022 HXY Z008 Z023 FX Z076 Z103 F Z036 Z XY Z037 Z050 Z062 Z010 Z024 XY Z038 Z051 Z063 Z011 Z025 X Z Z039 Z052 Z064 Z012 Z026 F Z040 Z013 FXY Z XY Z041 Z053 Z065 Z014 Z XY Z042 Z054 Z066 Z015 Z028 Z043 Z055 Z067 Z082 Z016 Z029 Y Z085 X Z092 Y Z XY Z044 Z056 Z068 Z017 Z030 Z089 XY Z045 Z057 Z069 Z018 Z FY Z019 Z097 Z046 Z058 Z070 Z Y Z098 Z081 XY FY Z079 Z083 Z F Z075 Y Z087 Z F Z074

47 46 Directional control valve D07 (NG16) Specifications General Design Spool valve Mounting type Subplate, DO7 (NG 16) Mounting osition as desired (Horizontal only for detented valves) mbient temperature 4 to 120 F (-20 to 50 C) Seals Viton CS Certified File Number LR (Except flame proof solenoids) Weights Hydraulic 17.6 lbs (8 kg) Electrical 1 Solenoid 19.8 lbs (9 kg) Electrical 2 Solenoid 20.9 lbs (9.5 kg) Response time adjustment 2.4 lbs (1.1 kg) Hydraulic Fluid etroleum hydraulic fluids and most fire resistant fluids Viscosity SUS ( cst) Fluid temperature 4 to 175 F ( 20 to 80 C) Filtration Contamination class 19/16, according to ISO 4406 to be realized with filter ß25 = 75 Direction of flow s shown on symbol Operating pressure ort,,,: 5075 SI (350 bar) max. ort : 4060 SI (280 bar) max. w/flame proof solenoids ilot pressure ilot port X or 114 psi (8 bar) min psi (250 bar) max. Drain port Y or 2300 psi (160 bar) max. for solenoid operated 3625 psi (250 bar) max. for hydraulic piloted 1450 psi (100 bar) max. for flame proof solenoid Maximum flow 80 GM (300 L/min) see /Q curve page 47 Control volume 0.37 in 3 (6 cm 3 ) for 3 position valves 0.61 in 3 (10 cm 3 ) for 2 position valves otal response time Switch-on ilot = 700 psi ms Switch-off ressure (50 bar) = DC ms Switch-on ilot = 2900 psi ms Switch-off ressure (200 bar) ms Switch-on ilot = 700 psi ms Switch-off ressure (50 bar) C ms Switch-on ilot = 2900 psi ms Switch-off ressure (200 bar) ms Electric Duty factor 100% Solenoid identification Meets NSI (R 1988) Standards* when Sol. is energized. Enclosure type *I 65 to IEC and DIN (DIN Connectors) Insulation class C VDE 5 Voltage and frequency See table on page 88 C-solenoids 230/60 can be used with 220/50 and 115/60 can be used with 110/50 voltage supply Voltage tolerance Nominal Voltage ±10% ower rating DC In Rush: 33W Holding: 33W C In Rush: ~ 1.5 Holding: ~ 0.54 *Note: I 65 rotected against low pressure water jets from all direction Dust tight

48 Directional control valve D07 (NG16) 47 erformance Data Curve Viscosity = 142 SUS (30.2 cst) Symbol ar psi ressure Drop GM L/min Flow

49 48 Directional control valve D07 (NG16) ilot & Drain Options Max. ressure in or X: 3625 psi (250 bar) Max. ressure in or Y: 3045 psi (210 bar) for type 3 control 3625 psi (250 bar) for type 2 control 1450 psi (100 bar) when using flame proof solenoid ilot oil supply and drain are either external via the X and Y ports or internal via the and ports. Conversion is possible by removing or installing plugs which are accessible after removing the pilot valve. When using internal pilot and drain, the X and Y ports in the subplate must be plugged. Y IN. ILO, EX. DRIN; LUG ORS 2 & 3 IN. ILO, IN. DRIN; LUG ORS 3 & 4 XY EX. ILO, EX. DRIN; LUG ORS 1 & 2 X EX. ILO, IN. DRIN; LUG ORS 1 & 4 XY HYDRULIC ILO; LUG ORS 1 & 2 Sol Sol v v 1 x Y X Y 3 4 lug art No M6 DIN Fixed ilot Chokes fixed pilot choke is an orifice placed in the pilot line to increase the spool shift time. Metering notches on the spool are standard and by increasing the shift time of the spool, the flow paths are opened and closed more gradually which reduces system shock. Fixed pilot chokes can be added to a standard valve at any time by simply removing the pilot valve and inserting the choke in the port. he flange machined on the choke holds it captive in the counter-bore for the O-ring. he chokes can be inserted in any of the ports of the pilot valve depending on the desired result. hen a valve is ordered with a fixed pilot choke the (Imm) diameter orifice is installed in the port. Chokes with other size orifice are available and are listed below. Orifice Sismeter art Number ilot valve (0.8mm) (1mm) (1.2mm) Fixed pilot choke (2mm) Main valve

50 Directional control valve D07 (NG16) 49 djustable ilot Chokes djustable chokes consist of a modular flow control valve which contains two non-pressure compensated throttle valves with free flow checks. It provides independent control of the spool shift time in both direc-tions. ecause the port pattern is symmet-rical and a seal plate is used, the module can be turned 180 to provide either meter-in or meter-out control. Meter-out is standard. If meter-in is needed, the pilot valve must be removed and the flow control module rotated 180 on its longitudi-nal axis. he locating pin in the bottom mount-ing surface of the flow control module must be removed and installed on the opposite side before reassembly. he seal plate always remains on top of the main valve body. orque value for the mounting bolts of the pilot valve is 5.0 lb/ft (7.0 Nm). MEER-OU (SNDRD) MEER-IN (URN MODULR VLVE 180º) SOL SOL SOL SOL X Y X Y ILO CHOKE DJUSING SCREW (OH ENDS) 6mm (40.0) 883 RCINE, WI U.S.. max psi For Conversion Description art number NG6 Flow control module w/seal plate (meter out) Seal plate x M5 x 70, DIN (art number is for one bolt)

51 50 Directional control valve D07 (NG16) ilot ressure Valve D Sol Sol X Y v ar psi ressure Drop GM L/min Flow he pilot pressure valve is a slip-in cartridge which fits into a machined cavity in the pressure port of the main valve. It is used to create pilot pressure when using open center spools (000 and 002). ilot pressure is fed internally to the pilot valve. he pressure drop across the pilot pressure valve is additive to the pressure drop across the main valve. he machined cavity, to accept the pilot pressure cartridge, is standard on all valves. For Conversion Description art Number ilot pressure valve cartidge

52 Directional control valve D07 (NG16) 51 djustable Spool Stops djustable spool stops are used to limit the stroke of the spool and are located on both ends of the valve. hey provide independent control of the actuator speed in either directions. Limiting the spool stroke creates an orifice between the body and spool in either flow path and turning the screw in will reduce the size of the orifice. If the flow through both flow paths is equal, the valve will meter-in and out at the same time. When a differential cylinder is used, the stops can be adjusted to obtain the same speed in both directions. Y Germany 0.35 (9) djustment range 4.02 (102) (304) 7.95 (202) Inches (Millimeters) For Conversion Description art number Complete end cap assembly including mounting bolts

53 RCINE, WI U.S.. RCINE, WI U.S.. max psi max psi 52 Directional control valve D07 (NG16) Valve With C/DC Solenoid nd Wiring 2.63 (66.9) Name ag describes complete valve (198.7) 5.63 (143.1) Inches (Millimeters) Name ag describes pilot valve. Name ag describes main valve (189) 6.56 (166.5) 1.34 (34) 3.74 (95) Spool 11 & (20) 5.51 (140) 9.33 (237) 9.33 (237) 8.43 (214) Spool 9 & (69.9) (89) 2x 9 x 2 4x 23 x 2.5 2x 1/4-20 x 1.75" long = 10 lb/ft (13Nm) 4x 3/8-16 x 2.00" long = 40 lb/ft (54Nm) Valve With C Solenoid (DIN) 2.63 (66.9).47(12.0) 7.82 (198.7) 5.63 (143.1) Name ag describes complete valve. Inches (Millimeters) Name ag describes pilot valve. Name ag describes main valve (189) 1.34 (34) 3.74 (95) Spool 11 & (20) 5.51 (140) 9.33 (237) 9.33 (237) 8.43 (214) Spool 9 & (69.9) (89) 2x 9 x 2 4x 23 x 2.5 2x 1/4-20 x 1.75" long = 10 lb/ft (13Nm) 4x 3/8-16 x 2.00" long = 40 lb/ft (54Nm)

54 883 RCINE, WI U.S.. max psi Directional control valve D07 (NG16) 53 Valve With DC Solenoid (DIN) 2.63 (66.9).47(12.0) 7.82 (198.7) 5.63 (143.1) Name ag describes complete valve. Inches (Millimeters) Name ag describes pilot valve. Name ag describes main valve (189.7) 1.34 (34) 3.74 (95) Spool 11 & (20) 5.51 (140) 9.33 (237) 9.33 (237) 8.43 (214) Spool 9 & (69.9) (89) 2x 9 x 2 4x 23 x 2.5 2x 1/4-20 x 1.75" long = 10 lb/ft (13Nm) 4x 3/8-16 x 2.00" long = 40 lb/ft (54Nm) Hydraulic Controlled (ype 2) Inches (Millimeters) Name ag describes complete valve (34) (117) 3.74 (95) RCINE, WI U.S.. max psi 0.79 (20) 5.51 (140) 9.33 (237) 8.43 (214) 2x 1/4-20 x 1.75" long 4x 3/8-16 x 2.00" long = 10 lb/ft (13Nm) = 40 lb/ft (54Nm) Spool (69.9) (89) 2x 9 x 2 4x 23 x 2.5

55 54 Directional control valve D07 (NG16) Subplates, ottom orted C port is used for load sensing when using proportional valves. Inches (Millimeters) When a subplate is not used, a machined pad must be provided for mounting which is flat to within in./in. and has a surface finish of 63 RMS (150.8).5 (12.7) 4.0 (101.6) 1.5 (38.1) (71.5) 2.25 (57.1) 2.19 (55.6) 1.37 (34.8).56 (14.2) (92.1) 2.75 (69.8).62 (15.7).063 (1.6) 1.97 (50.0) 2.6 (66.0) (76.6) 3.47 (88.1).72 (18.3) (34.0).938 (23.8).50 (12.7).75 (19.0) 2.62 (64.0) (33.3) 6.94 (176.3) (84.2) (77.8) (39.6) X Y C (58.6) 4.62 (117.3) (46.8) (62.7) (97.6) (113.5) (153.8) SE.750 (19.0) N.812 (20.6),,,, X,Y,C, Maximum pressure Weight art Number 3/4 NF 1/4 NF 5000 psi 15 lbs NF (350 bar) (6.8 kg) #12 SE #6 SE #16 SE olt kit -231 (Valve only) 4x 3/8-16 x 2 long 2x 1/4-20 x 1-3/4 long

56 Directional control valve D08 (NG25) 3000 SI 55 Features and enefits n n n Retained guide tube for easy replacement of coils Solenoid identification per U.S. standard. when solenoid is energized Optional manual overrides available n Certified ilot Valve Main section certification pending n n n Dual frequency solenoids (50 or 60 Hertz) hrottling notches in body are standard Optional load check

57 56 Directional control valve D08 (NG25) 3000 SI Order Code his order code describes the desired model variances of the DO8 (NG 25) directional control valves. Standard models are assigned a 10-digit number. See page W V V 3 D 5 1 / 5 5 / SIZE 06 D08 (NG 25) SELS V VION SD. CONROL YE 2 HYDRULIC 3 ELECRICL SOOL CODE REFER O SOOL CHR ON GE 57 ILO CHOKES* F FIXED DJUSLE R LOD CHECK IN OR* 09 MNUL USH IN WIH RUER COVER* 55 LOW RESSURE VERSION 51 SOLENOID IDENIFICION ER U.S. SNDRD WHEN SOLENOID IS ENERGIZED (NSI 93.9) D DESIGN SERIES D SD **E 24VDC LED WIRE COIL SOLENOID OIONS* C COVERED USH IN * If these options are not needed, omit them from the code H DJUSLE SOOL SOS* ILO ND DRIN XY EX. ILO EX. DRIN IN. ILO IN. DRIN Y IN. ILO EX. DRIN X EX. ILO IN. DRIN ** QUICK CONNEC FOR E SERIES IS MINI CONNECOR (See G 89) ELECRICL CONNECIONS WS DIN 43650/ISO4400 KL WIRING OX + SEN. LIGHS K WIRING OX KD WIRING OX + QUICK CONN. (NSI 93.55m IN SINGLE SOL. & 5 IN. DOULE. SOL.) KE WIRING OX + QUICK CONN. + SEN. LIGHS KG WIRING OX + QUICK CONN. (SINGLE SOL. 5 IN) KM WIRING OX + QUICK CONN. + SEN. LIGHS (SINGLE SOL. 5 IN) EX FLME ROOF SOLENOID SOLENOID VOLGES C DC 115/60 012/00 230/60 024/00 Series D Dual Frequency roduct Literature Disclaimer SECIFICIONS ND/OR DIMENSIONS RE SUJEC O CHNGE WIHOU RIOR NOICE. LESE CONSUL FCORY.

58 Directional control valve D08 (NG25) 3000 SI 57 art Numbers Standard valves are assigned a 10-digit part number. Describe unassigned valve combinations with the alpha-numeric order code. IN. ILO X EX. ILO IN. DRIN Y EX. DRIN Z K WIRING OX KD WIRING OX + QUICK CONNEC (3 IN SINGLE & 5 IN DOULE SOLENOID) KE WIRING OX + QUICK CONNEC + SENINEL LIGHS KG WIRING OX + QUICK CONNEC (SINGLE SOLENOID 5 IN) KL WIRING OX + SENINEL LIGHS KM WIRING OX + QUICK CONNEC + SENINEL LIGHS (SINGLE SOL. 5 IN) WS LUG CONNECER (DIN / ISO 4400) K KD KE KG KL KM WS WS SOOL SYMOLS RNSIION ILO 110/ / / / / / / VDC. NO. & DRIN Y Z506 Z XY Z583 X Z578 Z505 Z517 Z628 Z547 Z Y Z553 Z576 Z631 Z536 XY Z629 Z626 Z588 Y Z507 Z530 Z XY Z562 Z573 Z613 X Z563 Z568 Z Z508 Z531 Z545 Z544 Z575 Y Z555 Z611 Z581 Z594 XY Z667 FY Z621 Z Y Z608 XY Z564 Z532 Z Y Z577 XY Z570 Z617 Z543 Z512 Z518 Z625 Z551 Z571 Y Z558 Z XY Z560 Z627 Z668 X Z624 F Z659 Z511 Z643 Z550 Z Y Z633 Z620 Z513 Z528 Z642 Z542 Z XY Z561 Y Z675 Z639 Z510 Z548 Z612 Z Y Z614 Z XY Z674 F Z654 Y Z598 Z514 Z597 D4 F Z660

59 58 Directional control valve D08 (NG25) 3000 SI Specifications General Design Spool valve Mounting type Subplate, DO8 (NG 25) Mounting osition mbient temperature Seals CS Certified as desired (Horizontal only for detented valves) 4 to 120 F (-20 to 50 C) Viton File Number LR (Except flame proof solenoids) Weights Hydraulic 25.0 (11.3) Electrical 1 Solenoid 26.6 (12.1) Electrical 2 Solenoid 27.3 ( 12.4) djustable ilot Chokes 2.4 lbs (1.1kg) Hydraulic Fluid Viscosity Fluid temperature etroleum hydraulic fluids and most fire resistant fluids SUS ( cst) 4 to 175 F ( 20 to 80 C) Filtration Contamination class 19/16, according to ISO 4406 to be realized with filter ß25=75 Direction of flow Operating pressure ilot pressure s shown on symbol ort,,,: 3000 SI (210 bar) max. ort : 1500 SI (100 bar) max. w/flame proof solenoids 65 SI (4.5 bar)min SI (210 bar) max. Maximum flow 75 GM (284 L/min) see /Q curve page 59 Control volume 0.5 in 3 (8 cm 3 ) for 3 position valves Electric Duty factor 100% Solenoid identification Enclosure type Meets NSI/ (R 1988) Standards* when Sol. is energized. *I 65 to IEC and DIN (DIN Connectors) Insulation class C VDE 5 Voltage and frequency See table on page 88 C-solenoids 230/60 can be used with 220/50 and 115/60 can be used with 110/50 voltage supply Voltage tolerance Nominal Voltage ±10% ower rating DC In Rush: 33W Holding: 33W C In Rush: ~ 1.5 Holding: ~ 0.54 Response time 25 90ms Dependent on control pressure and spool Switching frequency max. 1800/h *Note: I 65 rotected against low pressure water jets from all direction Dust tight

60 Directional control valve D08 (NG25) 3000 SI 59 erformance Data RESSURE DRO R SI LL SOOLS EXCE 002 ll Flow aths GM L/min. FLOW R SI SOOL RESSURE DRO to to to GM L/min. FLOW Viscosity = 142 SUS (30.2 cst)

61 60 Directional control valve D08 (NG25) 3000 SI ressure ort Check he pressure port check is a load check which prevents the load from dropping when several valves are connected in parallel. It will not create pilot pressure for internal pilot when using open center spools. he standard valve body is not machined for the check valve cartridge. SOL SOL ressure ort Check Cartridge X Y ilot & Drain Options ilot oil supply and drain are either external via the X and Y ports or internal via the and ports. here are four threaded ports and only two plugs (1/16 N). he installations of the plugs determines the source of the pilot oil and where it drains. Valves can be converted in the field. When installing plugs in port 1 and 2, care must be taken that the plug is screwed in all the way or both passages will be blocked. Y IN. ILO, EX. DRIN; LUG ORS 2 & 3 IN. ILO, IN. DRIN; LUG ORS 3 & 4 XY EX. ILO, EX. DRIN; LUG ORS 1 & 2 X EX. ILO, IN. DRIN; LUG ORS 1 & 4 XY HYDRULIC ILO; LUG ORS 1 & O VIEW WIH ILO SECION REMOVED EX. ILO (X) EX. DRIN (Y) OOM VIEW

62 Directional control valve D08 (NG25) 3000 SI 61 djustable ilot Chokes djustable chokes consist of a modular flow control valve which contains two non-pressure compensated throttle valves with free flow checks. It provides independent control of the spool shift time in both direc-tions. ecause the port pattern is symmet-rical and a seal plate is used, the module can be turned 180 to provide either meter-in or meter-out control. Meter-out is standard. If meter-in is needed, the pilot valve must be removed and the flow control module rotated 180 on its longitudi-nal axis. he locating pin in the bottom mount-ing surface of the flow control module must be removed and installed on the opposite side before reassembly. he seal plate always remains on top of the main valve body. orque value for the mounting bolts of the pilot valve is 5.0 lb/ft (7.0 Nm). MEER-OU (SNDRD) MEER-IN (URN MODULR VLVE 180º) SOL SOL SOL SOL X Y X Y ILO CHOKE DJUSING SCREW (OH ENDS) 6mm (40.0) 9.20 (233.7) 8.33 (211.6) 6.46 (164.1) 4.78 (123.9) 3.94 (100.0) ILO CYL CYL SEL LE For Conversion Description art number NG6 Flow control module w/seal plate (meter out) Seal plate x x 2 3/4 Long (olt kit -215)

63 62 Directional control valve D08 (NG25) 3000 SI djustable Spool Stops djustable spool stops are used to limit the stroke of the spool and are located on both ends of the valve. hey provide independent control of the actuator speed in either directions. Limiting the spool stroke creates an orifice between the body and spool in either flow path and turning the screw in will reduce the size of the orifice. If the flow through both flow paths is equal, the valve will meter-in and out at the same time. When a differential cylinder is used, the stops can be adjusted to obtain equal speed in both directions. Complete end cap assemblies are available to convert standard valves. ( is the number for one end cap) DJUSLE SOOL SOS Limit stroke at either end. dd 5" (127mm) to valve length. EX. ILO EX. DRIN Fixed ilot Chokes Fixed pilot chokes consist of two orifices, 1/16 N pipe plug with a.040 (1.0) hole (405420), installed in the pilot lines going to each end cap. he orifices restrict the pilot oil and will increase the spool shift time. Metering notches in the body are standard and by slowly shifting the spool, the flow paths are opened and closed more gradually which reduces system shock. Chokes can be added to a standard valve at any time but an 1/8 N plug on each end of the main valve must be removed to gain access to the threaded pilot line. CHOKE 1/16" N LUG 1/8" N

64 Directional control valve D08 (NG25) 3000 SI 63 Valve With C/DC Solenoid & Wiring Inches (Millimeters) 1.67 (42.4) required to remove coil Name ag describes complete valve 9.35 (237.5) 5.63 (143.0) 1.52 (38.6) Name ag describes pilot valve 1/2" N ELECRICL CONNECION (both ends) 2.87 (72.9) ILO CYL CYL (275.8) 3.31 (84.1) Name ag describes main valve 7.62 (193.5) 6.75 (171.4) 4.88 (123.9) 3.94 (100.0).16 (4.1).44 (11.2) 4.50 (114.3) 2.25 (57.2) MNUL OVERRIDE (both ends) (standard) 1.04 (26.4) 2x 1/8" C.S. x 13/16" I.D. 4x 1/8" C.S. x 1" I.D. 6x 1/2-13 x 1.75" long = 70 lb/ft (95Nm) Valve With C Solenoid (DIN) Inches (Millimeters) 1.74 (44.2) required to remove coil.47 (11.9) required to remove connector 9.35 (237.5) 5.63 (143.0) Name ag describes complete valve 1.52 (38.6) Name ag describes pilot valve 1.81 (45.9).91 (23.1) MNUL OVERRIDE (both ends) (standard) 2.87 (72.9) ILO CYL CYL (275.8) 3.31 (84.1) Name ag describes main valve 7.61 (193.3) 4.88 (123.9) 3.94 (100.0).16 (4.1) (11.2) (57.1) 4.50 (114.3) 1.04 (26.4) 2x 1/8" C.S. x 13/16" I.D. 4x 1/8" C.S. x 1" I.D. 6x 1/2-13 x 1.75" long = 70 lb/ft (95Nm)

65 64 Directional control valve D08 (NG25) 3000 SI Valve With DC Solenoid (DIN) Inches (Millimeters) 1.97 (50.0).47 (11.9) 9.65 (245.1) 5.93 (150.6) Name ag describes complete valve 1.22 (30.9) Name ag describes pilot valve 1.81 (45.9).91 (23.1) 2.87 (72.9) ILO CYL CYL (275.8) Name ag describes main valve 3.31 (84.1) 7.64 (194.1) 4.88 (123.9) 3.94 (100.0).16 (4.1).44 (11.2) 4.50 (114.3) MNUL OVERRIDE (both ends) (standard) 2.25 (57.2) 1.04 (26.4) 2x 1/8" C.S. x 13/16" I.D. 4x 1/8" C.S. x 1" I.D. 6x 1/2-13 x 1.75" long = 70 lb/ft (95Nm) Hydraulically Controlled (ype 2) Inches (Millimeters) (193.8) 4.43 (112.5) 3 4 EX. ILO 1.75 (44.5) EX. DRIN 5.12 (130.0) 3.94 (100.1) ILO CYL CYL (270.8) 4.50 (114.3) 2x 1/8" C.S. x 13/16" I.D. 4x 1/8" C.S. x 1" I.D. 6x 1/2-13 x 1.75" long = 70 lb/ft (95Nm)

66 Directional control valve D08 (NG25) 65 Subplates, ottom orted 6 HOLES 1/2-13 UNC-2 HD.94 ±.03 DEE (30.0).688 (17.5) (29.4) (100.8) (94.5) (76.9) (53.2) (130.2).75 (19.0).188 (4.8) Inches (Millimeters) (46.1) (74.6) (152.4) (92.1) 4.5 (114.3).530 (13.5) (45.8) (5.7) (124.5) (195.1) 4 HOLES.5625 DRILL HRU.75 (19.0) 3.0 (76.2) 8.74 (22.2) X C Y (110.9) (103.1) 3.0 (76.2) (49.2) (34.8) (64.9) (88.8) (133.1) (156.9) (187.1) (41.3) When a subplate is not used, a machined pad must be provided for mounting which is flat to within in./in. and has a surface finish of 63 RMS. C port is used for load sensing when using proportional valves.,,, X,Y,C max SI (bar) Weight Lbs. (kg) art Number 1 NF 1/4 NF 5000 (350) (Subplate only) 25(11.3) /4 NF /2 NF #16 SE #6 SE #20 SE #24 SE olt kit 114 (valve only) 6x 1/2 13 x 1.75 Long

67 66 Directional control valve D08 (NG25) 4600 SI Features and enefits n n n Retained guide tube for easy replacement of coils Solenoid identification per U.S. standard. when solenoid is energized Optional manual overrides available n Certified n n n Dual frequency solenoids (50 or 60 Hertz) hrottling spools are standard ilot pressure valve in port is optional

68 Directional control valve D08 (NG25) 4600 SI 67 Order Code his order code describes the desired model variances of the DO8 (NG 25) directional control valves. Standard models are assigned a 10-digit number. See page W V V 3 D 5 1 / SIZE 25 D08 (NG 25) SELS V VION SD. CONROL YE 2 HYDRULIC 3 ELECRICL SOOL CODE REFER O SOOL CHR ON GE 68 DJUSLE ILO CHOKES* F FIXED [ (1mm) dia. orifice] DJUSLE 09 MNUL USH IN WIH RUER COVER* 51 SOLENOID IDENIFICION ER U.S. SNDRD WHEN SOLENOID IS ENER- GIZED (NSI 93.9) D DESIGN SERIES D SD **E 24VDC LED WIRE COIL SOLENOID OIONS* C COVERED USH IN * If these options are not needed, omit them from the code R CK RESSURE VLVE IN * H DJUSLE SOOL SOS* ILO ND DRIN XY EX. ILO EX. DRIN IN. ILO IN. DRIN Y IN. ILO EX. DRIN X EX. ILO IN. DRIN ** QUICK CONNEC FOR E SERIES IS MINI CONNEC- OR (See G 89) ELECRICL CONNECIONS WS DIN 43650/ISO4400 KL WIRING OX + SEN. LIGHS K WIRING OX KD WIRING OX + QUICK CONN. (NSI 93.55m IN SINGLE SOL. & 5 IN. DOULE. SOL.) KE WIRING OX + QUICK CONN. + SEN. LIGHS KG WIRING OX + QUICK CONN. (SINGLE SOL. 5 IN) KM WIRING OX + QUICK CONN. + SEN. LIGHS (SINGLE SOL. 5 IN) EX FLME ROOF SOLENOID SOLENOID VOLGES C DC 115/60 ll solenoids 012/00 230/60 are dual frequency 024/00 (50 or 60hz) roduct Literature Disclaimer SECIFICIONS ND/OR DIMENSIONS RE SUJEC O CHNGE WIHOU RIOR NOICE. LESE CONSUL FCORY.

69 68 Directional control valve D08 (NG25) 4600 SI art Numbers Standard valves are assigned a 10-digit part number. Describe unassigned valve combinations with the alpha-numeric order code. IN. ILO X EX. ILO IN. DRIN Y EX. DRIN Z K WIRING OX KD WIRING OX + QUICK CONNEC (3 IN SINGLE & 5 IN DOULE SOLENOID) KE WIRING OX + QUICK CONNEC + SENINEL LIGHS KG WIRING OX + QUICK CONNEC (SINGLE SOLENOID 5 IN) KL WIRING OX + SENINEL LIGHS KM WIRING OX + QUICK CONNEC + SENINEL LIGHS (SINGLE SOL. 5 IN) WS LUG CONNECER (DIN / ISO 4400) K KD KE KG KL KM WS WS SOOL SYMOLS RNSIION ILO 110/ / / / / / / VDC. NO. & DRIN 000 XY Z033 Z047 Z059 Z005 Z020 Y Z077 Z085 XY Z034 Z048 Z060 Z006 Z021 Z035 Z049 Z061 Z007 Z a b Y HXY Z079 Z008 Z023 FX Z076 F Z036 Z009 Z XY Z037 Z050 Z062 Z010 Z024 Y Z XY Z038 Z039 Z051 Z052 Z063 Z064 Z011 Z012 Z025 Z026 F Z040 Z XY Z041 Z053 Z065 Z014 Z027 XY Z042 Z054 Z066 Z015 Z X Z081 Z043 Z055 Z067 Z016 Z029 Y Z XY Z044 Z056 Z068 Z017 Z030 Y Z099 XY Z045 Z057 Z069 Z018 Z FY Z019 Z046 Z058 Z070 Z032

70 Directional control valve D08 (NG25) 4600 SI 69 Specifications General Design Spool valve Mounting type Subplate, DO8 (NG 25) Mounting osition as desired (Horizontal only for detented valves) mbient temperature 4 to 120 F (-20 to 50 C) Seals Viton CS Certified File Number LR (Except flame proof solenoids) Weights Hydraulic 35.3 lbs (16 kg) Electrical 1 Solenoid 37.5 lbs (17 kg) Electrical 2 Solenoid 38.5 lbs (17.5) Response time adjustment 2.4 lbs (1.1 kg) Hydraulic Fluid etroleum hydraulic fluids and most fire resistant fluids Viscosity SUS ( cst) Fluid temperature 4 to 175 F ( 20 to 80 C) Filtration Contamination class 19/16, according to ISO 4406 to be realized with filter ß25 = 75 Direction of flow s shown on symbol Operating pressure ort,,, : 5075 SI (350 bar) max. ort : 4060 SI (280 bar) max. w/flame proof solenoids ilot pressure ilot port X or 114 psi (8 bar) min psi (250 bar) max. Drain port Y or 2300 psi (160 bar) max. for solenoid operated 3625 psi (250 bar) max. for hydraulic piloted 1450 psi (100 bar) max. for flame proof solenoid Maximum flow 185 GM (700 L/min) see /Q curve page 70 Control volume 0.92 in 3 (15 cm 3 ) for 3 position valves 1.34 in 3 (22 cm 3 ) for 2 position valves otal response time Switch-on Switch-off ilot ressure = 700 psi (50 bar) = DC ms ms Switch-on ilot = 2900 psi ms Switch-off ressure (200 bar) ms Switch-on ilot = 700 psi ms Switch-off ressure (50 bar) C ms Switch-on ilot = 2900 psi ms Switch-off ressure (200 bar) ms Electric Duty factor 100% Solenoid identification Meets NSI (R 1988) Standards* when Sol. is energized. Enclosure type *I 65 to IEC and DIN (DIN Connectors) Insulation class C VDE 5 Voltage and frequency See table on page 88 C-solenoids 230/60 can be used with 220/50 and 115/60 can be used with 110/50 voltage supply Voltage tolerance Nominal Voltage ±10% ower rating DC In Rush: 33W Holding: 33W C In Rush: ~ 1.5 Holding: ~ 0.54 *Note: I 65 rotected against low pressure water jets from all direction Dust tight

71 70 Directional control valve D08 (NG25) 4600 SI erformance Data Curve Symbol Viscosity = 142 SUS (30.2 cst) ar psi ressure Drop ` GM Flow L/min

72 Directional control valve D08 (NG25) 4600 SI 71 ilot & Drain Options Max. ressure in or X: 3625 psi (250 bar) Max. ressure in or Y: 3045 psi (210 bar) for type 3 control 3625 psi (250 bar) for type 2 control 1450 psi (100 bar) when using flame proof solenoid ilot oil supply and drain is either external via the x and y ports or internal via the and ports. Conversion is possible by removing or installing plugs. lug no. 1 is accessible from the bottom of the main valve. he pilot valve must be removed to gain access to plug No. 2. When using internal pilot and drain, the X and Y ports in the subplate must be plugged. Y IN. ILO, EX. DRIN; LUG ORS 2 & 3 IN. ILO, IN. DRIN; LUG ORS 3 & 4 XY EX. ILO, EX. DRIN; LUG ORS 1 & 2 X EX. ILO, IN. DRIN; LUG ORS 1 & 4 XY HYDRULIC ILO; LUG ORS 1 & 2 Sol Sol X Y 3 4 lug art No /4 S 7 3 ND 4 RE EXERNL OF HE VLVE M6 DIN Fixed ilot Chokes fixed pilot choke is an orifice placed in the pilot line to increase the spool shift time. Metering notches on the spool are standard and by increasing the shift time of the spool, the flow paths are opened and closed more gradually which reduces system shock. Fixed pilot chokes can be added to a standard valve at any time by simply removing the pilot valve and inserting the choke in the port. he flange machined on the choke holds it captive in the counterbore for the O-ring. he chokes can be inserted in any of the ports of the pilot valve depending on the desired result. hen a valve is ordered with a fixed pilot choke the (lmm) diameter orifice is installed in the port. Chokes with other size orifice are available and are listed below. Orifice Diameter art Number ilot valve (0.8mm) (1mm) (1.2mm) (2mm) Fixed pilot choke Main valve

73 Directional control valve D08 (NG25) 4600 SI djustable ilot Chokes djustable chokes consist of a modular flow control valve which contains two non-pressure compensated throttle valves with free flow checks. It provides independent control of the spool shift time in both directions. ecause the port pattern is symmetrical and a seal plate is used, the module can be turned 180 to provide either meter-in or meter-out control. Meter-out is standard. If meter-in is needed, the pilot valve must be removed and the flow control module rotated 180 on its longitudinal axis. he locating pin in the bottom mounting surface of the flow control module must be removed and installed on the opposite side before reassembly. he seal plate always remains on top of the main valve body. orque value for the mounting bolts of the pilot valve is 5.0 lb/ft (7.0 Nm). MEER-OU (SNDRD) MEER-IN (URN MODULR VLVE 180º) SOL SOL SOL SOL X Y X Y ILO CHOKE DJUSING SCREW (OH ENDS) 6mm (40.0) X RCINE, WI U.S.. max psi SEL LE For Conversion Description art number NG6 Flow control module w/seal plate (meter out) Seal plate x M 5 x 70, DIN (art number is for one bolt)

74 Directional control valve D08 (NG25) 4600 SI 73 ilot ressure Valve D Sol Sol X Y v ar psi ressure Drop GM L/min Flow he pilot pressure valve is a slip-in cartridge which fits into a machined cavity in the pressure port of the main valve. It is used to create pilot pressure when using open center spools (000 and 002). ilot pressure is fed internally to the pilot valve. he pressure drop across the pilot pressure valve is additive to the pressure drop across the main valve. he machined cavity, to accept the pilot pressure cartridge, is standard on all valves. For Conversion Description art Number ilot pressure valve cartidge

75 74 Directional control valve D08 (NG25) 4600 SI djustable Spool Stops djustable spool stops are used to limit the stroke of the spool and are located on both ends of the valve. hey provide independent control of the actuator speed in either directions. Limiting the spool stroke creates an orifice between the body and spool in either flow path and turning the screw is will reduce the size of the orifice. If the flow through both flow paths is equal, the valve will meter-in and out at the same time. When a differential cylinder is used, the stops can be adjusted to obtain the same speed in both directions. X 883 RCINE, WI U.S.. max psi 0.39 (10) djustment range 4.53 (115) (384) (269) Inches (Millimeters) For Conversion Description art number Complete end cap assembly including mounting bolts

76 RCINE, WI U.S.. max psi RCINE, WI U.S.. max psi Directional control valve D08 (NG25) 4600 SI 75 Valve With C/DC Solenoid nd Wiring 2.63 (66.9) 7.82 (198.7) 5.63 (143.1) Name ag describes complete valve. Inches (Millimeters) Name ag describes pilot valve. X Name ag describes main valve (220) 7.74 (196.5) 4.92 (125) 1.69 (43) 3.46 (88) 0.71 (18) (305) 7.48 (190) 3.63 (92.1) 4.58 (116.4) 6x 1/2-13 x 2.5" long = 70 lb/ft (95Nm) 2x 15 x 2.5 4x 28 x 3 Valve With C Solenoid (DIN) 2.63 (66.9).47 (12.0) 7.82 (198.7) 5.63 (143.1) Name ag describes complete valve. Inches (Millimeters) Name ag describes pilot valve. X Name ag describes main valve (219) 1.69 (43) 4.92 (125) 3.46 (88) 0.71 (18) (305) 7.48 (190) 3.63 (92.1) 4.58 (116.4) 6x 1/2-13 x 2.5" long = 70 lb/ft (95Nm) 2x 15 x 2.5 4x 28 x 3

77 RCINE, WI U.S.. max psi 76 Directional control valve D08 (NG25) 4600 SI Valve With DC Solenoid (DIN) 2.93 (74.4).47 (12.0) 8.43 (214.1) 5.93 (150.6) Name ag describes complete valve. Inches (Millimeters) Name ag describes pilot valve. X Name ag describes main valve (219.7) 4.92 (125) 1.69 (43) 3.46 (88) 0.71 (18) (305) 7.48 (190) 3.63 (92.1) 4.58 (116.4) 6x 1/2-13 x 2.5" long = 70 lb/ft (95Nm) 2x 15 x 2.5 4x 28 x 3 Hydraulic Controlled (ype 2) Inches (Millimeters) Name ag describes complete valve. X 1.69 (43) RCINE, WI U.S.. max psi 5.79 (147) 4.92 (125) 3.46 (88) 0.71 (18) (305) 7.48 (190) 3.63 (92.1) 4.58 (116.4) 6x 1/2-13 x 2.5" long = 70 lb/ft (95Nm) 2x 15 x 2.5 4x 28 x 3

78 Directional control valve D08 (NG25) 4600 SI 77 Subplates, ottom orted C port is used for load sensing when using proportional valves. 6 HOLES 1/2-13 UNC-2 HD.94 ±.03 DEE.688 (17.5) (30.0) (29.4) (100.8) (94.5) (76.9) (53.2) (130.2).75 (19.0).188 (4.8) Inches (Millimeters) (46.1) (74.6) (152.4) (92.1) 4.5 (114.3).530 (13.5) (45.8) (5.7) (124.5) (195.1) 4 HOLES.5625 DRILL HRU.75 (19.0) 3.0 (76.2) 8.74 (22.2) X C Y (110.9) (103.1) 3.0 (76.2) (49.2) When a subplate is not used, a machined pad must be provided for mounting which is flat to within in./in. and has a surface finish of 63 RMS (34.8) (64.9) (88.8) (133.1) (156.9) (187.1) (41.3),,,, X,Y,C, Maximum ressure Weight art Number 1 NF 1/4 NF 5000 psi 25 lbs /4 NF (350 bar) (11.3 kg) /2 NF #16 SE #6 SE #20 SE #24 SE olt kit -228 (Valve only) 6 x 1/2 13 x 2.5 Long

79 78 Directional control valve D10 (NG32) 3000 SI Features and enefits n n n Retained guide tube for easy replacement of coils Solenoid identification per U.S. standard. when solenoid is energized Optional manual overrides available n Certified ilot Valve Main section certification pending n n n Dual frequency solenoids (50 or 60 Hertz) hrottling spools are available Optional load check

80 Directional control valve D10 (NG32) 3000 SI 79 Order Code his order code describes the desired model variances of the D10 (NG 32) directional control valves. Standard models are assigned a 10-digit number. See page W V V 3 D 5 1 / 5 5 / SIZE 32 - D10 (NG32) SELS V VION SD. CONROL YE 2 HYDRULIC 3 ELECRICL SOOL CODE REFER O SOOL CHR ON GE 80. ILO CHOKES* F FIXED DJUSLE R LOD CHECK IN OR* 09 MNUL USH IN WIH RUER COVER* 55 LOW RESSURE VERSION 51 SOLENOID IDENIFICION ER U.S. SNDRD WHEN SOLENOID IS ENERGIZED (NSI 93.9) D DESIGN SERIES D SD **E 24VDC LED WIRE COIL SOLENOID OIONS* C COVERED USH IN * If these options are not needed, omit them from the code H DJUSLE SOOL SOS* ILO ND DRIN XY EX. ILO EX. DRIN IN. ILO IN. DRIN Y IN. ILO EX. DRIN X EX. ILO IN. DRIN ** QUICK CONNEC FOR E SERIES IS MINI CONNECOR (See G 89) ELECRICL CONNECIONS WS DIN 43650/ISO4400 KL WIRING OX + SEN. LIGHS K WIRING OX KD WIRING OX + QUICK CONN. (NSI 93.55m IN SINGLE SOL. & 5 IN. DOULE. SOL.) KE WIRING OX + QUICK CONN. + SEN. LIGHS KG WIRING OX + QUICK CONN. (SINGLE SOL. 5 IN) KM WIRING OX + QUICK CONN. + SEN. LIGHS (SINGLE SOL. 5 IN) EX FLME ROOF SOLENOID SOLENOID VOLGES C DC 115/60 012/00 230/60 024/00 Series D Dual Frequency roduct Literature Disclaimer SECIFICIONS ND/OR DIMENSIONS RE SUJEC O CHNGE WIHOU RIOR NOICE. LESE CONSUL FCORY.

81 80 Directional control valve D10 (NG32) 3000 SI art Numbers Standard valves are assigned a 10-digit part number. Describe unassigned valve combinations with the alpha-numeric order code. IN. ILO X EX. ILO IN. DRIN Y EX. DRIN Z K WIRING OX KD WIRING OX + QUICK CONNEC (3 IN SINGLE & 5 IN DOULE SOLENOID) KE WIRING OX + QUICK CONNEC + SENINEL LIGHS KG WIRING OX + QUICK CONNEC (SINGLE SOLENOID 5 IN) KL WIRING OX + SENINEL LIGHS KM WIRING OX + QUICK CONNEC + SENINEL LIGHS (SINGLE SOL. 5 IN) WS LUG CONNECER (DIN / ISO 4400) K KD KE KG KL KM WS WS SOOL SYMOLS RNSIION ILO 110/ / / / / / / VDC. NO. & DRIN 000 XY Z529 Z505 Z538 Z XY Z508 Z536 X Z509 Y Z XY Z513 X Z512 Z516 Z527 Z Y Z XY Z528 Z517 Z XY Z Z520 Z Y Z Z Z525

82 Directional control valve D10 (NG32) 3000 SI 81 Specifications General Design Spool valve Mounting type Subplate, D10 (NG 32) Mounting osition mbient temperature Seals CS Certified as desired (Horizontal only for detented valves) 4 to 120 F (-20 to 50 C) Viton File Number LR (Except flame proof solenoids) Weights Hydraulic Electrical 1 Solenoid Electrical 2 Solenoid djustable ilot Chokes 83.2 lbs. (37.8 kg) 98 lbs. (44.5 kg) 99 lbs. (44.9 kg) 4.4 lbs. (2 kg) Hydraulic Fluid Viscosity Fluid temperature etroleum hydraulic fluids and most fire resistant fluids SUS ( cst) 4 to 175 F ( 20 to 80 C) Filtration Contamination class 19/16, according to ISO 4406 to be realized with filter ß25=75 Direction of flow Operating pressure ilot pressure s shown on symbol ort,,,: 3000 SI (210 bar) max. ort : 1500 SI (100 bar) max. w/flame proof solenoids 75 SI (5.2 bar)min SI (210 bar) max. Maximum flow 175 GM (660 L/min) see /Q curve page 82 Control volume 3.04 in 3 (50 cm 3 ) for 3 position valves Electric Duty factor 100% Solenoid identification Enclosure type Meets NSI/ (R 1988) Standards* when Sol. is energized. *I 65 to IEC and DIN (DIN Connectors) Insulation class C VDE 5 Voltage and frequency See table on page 88 C-solenoids 230/60 can be used with 220/50 and 115/60 can be used with 110/50 voltage supply Voltage tolerance Nominal Voltage ±10% ower rating DC In Rush: 42W C In Rush: ~ 3.5 Holding: ~ 1.14 Response time ms Dependent on control pressure and spool Switching frequency max. 1800/h *Note: I 65 rotected against low pressure water jets from all direction Dust tight

83 82 Directional control valve D10 (NG32) 3000 SI erformance Data LL SOOLS EXCE (6) 80 (5.5) er ath 70 (4.8) SI (bar) 60 (4) 50 (3.4) 40 (2.7) 30 (2) 20 (1.4) 10 (.7) 0 50 (190) 75 (215) 100 (380) 125 (475) 150 (570) 175 (665) GM (L/min.) 002 SOOL 200 (13.8) 180 (12) (11) 140 (36) SI (bar) 120 (8) 100 (6.9) 80 (5.5) 60 (4) 40 (2.7) 20 (1.4) 0 50 (190) 75 (215) 100 (380) 125 (475) 150 (570) 175 (665) GM (L/min.) Viscosity = 142 SUS (30.2 cst)

84 Directional control valve D10 (NG32) 3000 SI 83 ilot & Drain Options ilot oil supply and drain are either external via the X and Y ports or internal via the and ports. he 1 and D 2 ports are 1/8" N). he installations of the plugs determines the source of the pilot oil and where it drains. Valves can be converted in the field. Y IN. ILO, EX. DRIN; LUG ORS 2 & D 2 IN. ILO, IN. DRIN; LUG ORS 2 & D 1 XY EX. ILO, EX. DRIN; LUG ORS 1 & D 2 D 2 (LUG FOR EXERNL DRIN) -ORIFICE LUG (OIONL) 1 (LUG FOR EXERNL ILO) ORIFICE LUG (OIONL) 2 ILO OR (LUG FOR INERNL ILO) NK CYLINDER D 1 DRIN OR (LUG FOR INERNL DRIN) CYLINDER RESSURE djustable Choke Option 1.58 (40.3) 5.54 (140.7)

85 84 Directional control valve D10 (NG32) 3000 SI Valve With C/DC Solenoid & Wiring 4.25 (108.0) REQ'D. O REMOVE SOLENOID Y. OH ENDS 8.11 (206.0) 2.11 (53.6) 2.72 (69.1) Inches (Millimeters) 1.35 (34.3) 5.54 (140.7) (278.9) 9.91 (251.7).18 (4.6) 2.48 (63.0) 5.29 (134.4) 7.07 (179.6) 1.54 (39.1).42 (10.7) CYLINDER GGES CONNECIONS 1.69 (42.9) 9.00 (228.6) ().75 (19.1) 4.25 (108.0) ().79 (20.1).16 (4.1) 3.87 (98.3) 7.75 (196.8) SEL LE & SELS SULIED 2 LOCING INS, 0.25 (6.3) SEE SU-LE DEIL FOR LOCION Valve With C Solenoid (DIN) Inches (Millimeters) 4.25 (108.0) REQ'D. O REMOVE SOLENOID Y. OH ENDS.47 (11.9) 8.11 (206.0) 2.11 (53.6) (257.8) 5.54 (140.7) 5.29 (134.4) 9.00 (228.6) ().75 (19.1) () 6.25 (158.8) 7.75 (196.8)

86 Directional control valve D10 (NG32) 3000 SI 85 Valve With DC Solenoid (DIN) Inches (Millimeters) 4.25 (108.0) REQ'D. O REMOVE SOLENOID Y. OH ENDS 9.20 (233.7) 3.19 (81.0) (258.6) 5.54 (140.7) 5.29 (134.4) 9.00 (228.6) ().75 (19.1) () 6.25 (158.8) 7.75 (196.8) Hydraulically Controlled (ype 2) Inches (Millimeters) 1/4" NF ILO OR 'Y' 3.47 (88.1) 1/4" NF ILO OR 'X' 3.20 (81.3) 7.55 (191.8) 6.83 (173.5) 6.08 (154.4)

87 86 Directional control valve D10 (NG32) 3000 SI Subplates, ottom orted Inches (Millimeters) (266.7) NK - N (76.20) C (147.62) 2 HOLES FOR LOCING INS RESSURE - N 6 VLVE MG. HOLES 3/4-10 HD., (33.34) DEE (17.46) 7.75 (196.8) (158.75) D CYLINDER -N CYLINDER -N (28.57) F ILO DRIN - M (114.30) K O OOM E E (19.05) (41.27) 4 HOLES (16.67) DI. HRU L (38.10) G (114.30) H (190.50) ILO RESSURE - M (304.8) MODEL NO. C D E F G H J K L M N ottom (168.27) (114.30) (41.27) (123.82) (34.92) (41.27) (82.55) (147.64) (34.92) (123.82) (44.45) 1/4" NF 1-14" N ottom (168.27) (114.30) (41.27) (123.82) (34.92) (41.27) (82.55) (147.64) (34.92) (123.82) (44.45) 1/4" NF 1-1/2" N op (168.27) (114.30) (41.27) (123.82) (34.92) (41.27) (82.55) (147.64) (34.92) (123.82) (53.97) ottom /8" N 2" N (177.80) (130.17) (26.99) (114.3) (23.81) (15.87) (68.26) (160.34) (39.69) (130.17) (53.97)

88 Directional control valve accessories 87 ccessories Sentinel light assembly D03 (NG6) D05 (NG10) ort C ort Double C C Wiring ox Kit ort ort Double DC DC DC Quick connect Quick Connect female plug w/3 ft. pigtail for flexible conduit Quick Connect male plug for wiring box Quick Connect male plug for wiring box lug connector, Standard lug connector with LED indicator lamp VDC Single Sol. C Double Sol. C Single Sol. C Double Sol. C Single Sol. DC Double Sol. DC Grey () lack () Grey () lack () Rectifier lug Subplates D03 (NG6) D05 (NG10) D07 (NG16) D08 (NG25) D10 (NG32) 1.4 N NF 3.51M 3/8 N 1/2 N ottom orted 3/4 NF 1 NF 1 1/4 NF 1 1/2 NF 2" NF #6 SE #8 SE #12 SE #16 SE #20 SE #24 SE 1/4 N Side orted 3/8 N 1/2 N 3/4 N #6 SE #8 SE #12 SE

89 88 Directional control valve accessories SEL KIS Set of Seals (Viton) D03 (NG6) D05 (NG10) D07 (NG16) D08 (NG25/55) D08 (NG25) D10 (NG32) OL KIS Kit (valve only) hrottle Screw For Soft Shift djustment hrottle Screw for soft shift adjustment djustable Wt. Lbs (kg).001 (0.005) art Number Fixed.024 (0.6mm).040 (1mm) djustable * * * For speed adjustment when spool is moving in reference to cylinder parts Solenoid Nut Standard With Rubber Cover Covered 0.94 (24) 1.46 (37.2).1.18 (30) Inches (Milimeters) D03 (NG6) D05 (NG10) D03 (NG6) D05 (NG10) D03 (NG6) D05 (NG10) Solenoid Coil Voltage/Frequency 115/60 (Dual Frequency) 230/60 (Dual Frequency) 12VDC 24VDC 96VDC 125VDC 240VDC Flying Leads Din D03 (NG6) N/ N/ D05 (NG10) N/ D03 (NG6) N/ N/ D05 (NG10) N/ N/

90 Directional control valve accessories 89 Quick Connect Male lug C Solenoids Inches (Milimeters) he quick connect male plug is a standard three or five pole electrical connector with 3.25 leads except the ground lead which is 4. ll valves ordered with a quick connect are wired to an industry standard (NF Standard M) which is shown below. he wiring box has a 1/2 N electrical connection on each end in which the quick connect can be installed. On single solenoid valves, the quick connect will be located above the solenoid. On double solenoid valves, it is located on the port end of the valve. he five pin connector for a single solenoid valve is offered for consumers that use both single and double solenoid valves but want to standardize on one female quick connect plug..47 (11.9) CONNECOR FOR SINGLE SOLENOID 1 Green Lead (Ground) 3 Lead (o Solenoid).38 (9.6) Lead (o Solenoid) 1.00 (25.4) Hex. 1/2 N 1 Lead (o Sol. ) 1 Lead (o Solenoid) 5 Lead (o 2 Lead (Capped) Sol. ) 5 Lead (o Solenoid) 2 Lead (o Sol. ) Lead (o Sol. ) 3 Green Lead (Ground) Lead (Capped) 3 Green Lead (Ground) FIVE IN CONNECOR FOR DOULE SOLENOID FIVE IN CONNECOR FOR SINGLE SOLENOID DC Solenoids Inches (Milimeters) 1/2" - 14 N Receptacle ".313" " pigtails 1/2" N FCE OF MLE CONNECOR MOUNED ON VLVE FCE VIEW OF FEMLE CONNECOR IN #1 - + SOLENOID IN #2 - VLVE GROUND IN #3 - COMMON IN #4 - + SOLENOID NOE: SINGLE SOLENOID VLVES WIRED ON SOLENOID IN.

91 90 Directional control valve accessories Standard lug & lug With Lite 2.09 (53) 1.08 (27.5) Inches (Millimeters) 1.35 (34.2) G 11 M3.22 (5.5) Rectifier lug ~ UE 220/50 110/50 VDR = U 190/00 96/ U [V=] UE [V~] Sentinel Lite D03 (NG6) 3 (76.2) Double 2-7/8 (70.6) Single.35 (9) Sentinel Lite D08 (NG10) 5 (127) Double 4-1/2 (114.3) Single 1/2 (12.7) Female lug C Wire lead length 3 ft. ± 3 in. (.9m ± 7cm) Quick Connect C.62 (15.9) Quick Connect DC.54 (13.7)