03 SERIES. General Information Mounting Surface : ISO 4401-AC-05-4-A, CETOP-5, NFPA-DO2 Up to 25 MPa (3630 PSI), 70 L /min (18.5 U.S.

Transcription

1 3 SERIES General Information Mounting Surface : ISO 44-C--4-, CETO-, N-DO Up to Ma (363 SI), 7 L /min (8. U.S.GM) ub. EC-43 MODULR VLVES The modular valves are functional elements with which a hydraulic system can be composed and built easily by stacking them with the mounting bolts. Therefore, no piping is required for the manufacture of the hydraulic systems. Yuken's 3 Series Modular Valves are widely used to compose the hydraulic systems for the various industrial and marine equipment including machine tools, special purpose machines, steel mill equipment and ships. The valves have standardized mounting surface conforming to ISO 44-C--4- and optimum thickness for the stacking. Example of Stacking Configuration T W 3/8, Solenoid Operated Directional Valve (DSG-3) Modular Valves ase late (MMC-3) No.

2 3 SERIES Type of Modular Valve MODULR VLVES Type of Modular Valve Class Class Graphic age Graphic T age Solenoid Operated Directional Valve (S-)DSG /9 T-DSG G-DSG /9 T low Control Valves (for "-Line") M-3-/9 low Control and Check Valves (for "-Line", Metre-out) M-3-X-/9 Releif Valves (for "-Line") M-3- -3/39 7 low Control and Check Valves (for "-Line", Metre-in) M-3-Y-/9 Releif Valves (for "-Line") M-3- -3/39 7 low Control and Check Valves (for "-Line", Metre-out) M-3-X-/9 Releif Valves (for "-Line") M-3- -3/39 7 low Control and Check Valves (for "-Line", Metre-in) M-3-Y-/9 Releif Valves (for "&-Lines") MW-3- -3/39 7 low Control and Check Valves (for "&-Lines", Metre-out) MW-3-X-/9 Reducing Valves (for "-Line") MR-3- -3/39 low Control and Check Valves (for "&-Lines", Metre-in) MW-3-Y-/9 ressure Control Valves Reducing Valves (for "-Line") MR-3- -3/39 Reducing Valves (for "-Line") MR-3- -3/39 Reducing Valves for Low ressure Setting (for "-Line") MRL-3-/8/9 3 low Control Valves Temperature Compensated Throttle and Check Valves (for "-Line", Metre-out) MST-3-X-/9 Temperature Compensated Throttle and Check Valves (for "-Line", Metre-out) MST-3-X-/9 Temperature Compensated Throttle and Check Valves (for "&-Lines", Metre-out) MSTW-3-X-/ Reducing Valves for Low ressure Setting (for "-Line") MRL-3-/8/9 3 Throttle Valves (for "-Line") MS-3-3/39 7 Reducing Valves for Low ressure Setting (for "-Line") MRL-3-/8/9 3 Check and Throttle Valves (for "-Line") MSC-3-/9 9 Sequence Valves (for "-Line") MH-3- -/9 7 Throttle and Check Valves (for "-Line", Metre-out) MS-3-X-4/49 3 Counterbalance Valves (for "-Line") MH-3- -/9 7 Throttle and Check Valves (for "-Line", Metre-in) MS-3-Y-4/49 3 Counterbalance Valves (for "-Line") MH-3- -/9 7 Throttle and Check Valves (for "-Line", Metre-out) MS-3-X-4/49 3 or the details of solenoid operated directional valves, see the following catalogues: (S-)DSG-3- - T-DSG-3- -/9 - G-DSG-3- - ub.ec /9 : ub.ec-4 Throttle and Check Valves (for "-Line", Metre-in) MS-3-Y-4/49 Throttle and Check Valves (for "&-Lines", Metre-out) MSW-3-X-4/49 Throttle and Check Valves (for "&-Lines", Metre-in) MSW-3-Y-4/ No.

3 3 SERIES Type of Modular Valve MODULR VLVES Type of Modular Valve Class Graphic age Solenoid Operated Directional Valve (S-)DSG /9 T-DSG G-DSG /9 T Check Valves (for "-Line") MC-3- -/9 34 Check Valves (for "-Line") MC-3- -/9 34 Check Valves (for "-Line") MC-3- -/9 34 Directional Control Valves Check Valves (for "T-Line") MCT-3- -/9 Check Valves (for "&T-Lines") MCT-3- -T -/9 nti-cavitation Valves MC-3-/ ilot Operated Check Valves (for "-Line") M-3- -/9 39 ilot Operated Check Valves (for "-Line") M-3- -/9 39 ilot Operated Check Valves (for "&-Lines") MW-3- -/9 39 Modular lates and Mounting olts End lates (locking plates) MDC-3--/9 End lates (ypass plates) MDC-3--/9 Connecting lates MDS-3-/9 ase lates MMC-3-T- -/8/9 olt Kits MK-3- -/ or the details of solenoid operated directional valves, see the following catalogues: (S-)DSG-3- - T-DSG-3- -/9 - G-DSG-3- - ub.ec /9 : ub.ec-4 No.3

4 3 SERIES Instructions MODULR VLVES Instructions Caution in the selection of valves and circuit designing The selection of modular valves, to suit a particular function or hydraulic circuit, are made in exactly the same way as conventional valves, taking into account of the flow and pressure of each valve to be used. In some cases, the stacking system may be restricted, so please refer to the following instructions for stacking sequence. lease note, that when designing a system using modular stacking valves, due consideration should be given to working space for future maintenance. Stacking sequence when using reducing valves (for "" or "" line) and pilot operated check valves. ecause reducing valves are spool type, there is an internal leakage. In the stacking sequence shown in the drawing left (incorrect), the cylinder moves due to leakage through the pilot pressure line. Consequently, retaining the position of the cylinder using a pilot operated check valve becomes impossible. The stacking sequence shown in the drawing right (correct) is required in order to retain the cylinder position. Solenoid Operated Directional Valve ilot Operated Check Valve (for "&-Lines") Reducing Valve (for "-Line") (Incorrect) (Correct) T T Stacking sequence when using reducing valves (for "" or "" line) and throttle and check valves (for metreout). In to T flow in the drawing left (incorrect), pressure is generated at part with a throttle effect of the throttle and check valve. Depending upon the pressure so generated, the reducing valve may perform a pressure reducing function which causes a shortage of output power of the cylinder and spoils the smooth operation of the cylinder. Therefore, stacking sequence in the drawing right (correct) is required in this combination. Solenoid Operated Directional Valve Throttle and Check Valve (for "&-Lines, Metre-out") Reducing Valve (for "-Line") (Incorrect) (Correct) T T Stacking sequence when using pilot operated check valves and throttle and check valves (metre-out). In to T flow in the drawing left (incorrect), pressure is generated at part with a throttle effect of the throttle and check valve. The pressure so generated acts to shut the pilot operated check valve and eventually creates an open and shut operation of the valve repeatedly which may cause the cylinder to have a knocking effect (the same effect will occur in the case of to T flow). Therefore, the stacking sequence in the drawing right (correct) is required in this combination. Solenoid Operated Directional Valve Throttle and Check Valve (for "&-Lines, Metre-out") ilot Operated Check Valve (for "&-Lines") (Incorrect) (Correct) T T No.4

5 3 SERIES Specifications / Hydraulic luids / Others MODULR VLVES Specifications Max. Operating ressure... Ma (363 SI) Max. low... 7 L/min (8. U.S. GM) Number of Stack to stacks. 3. Ma (47 SI) for relief moduler valve (M/M/M/MW). L /min (3.7 U.S.GM) for throttle and check moduler valve (MS/MS/MSW) 3. Solenoid operated directional valve is included in the number of stack. 3 3/8 Solenoid Operated Directional Valves YUKEN 3 SERIES MODULR VLVES are designed for use with solenoid operated directional valve having an ISO 44-C--4- (CETO-, N-D) interface such as Yuken's DSG-3. lease refer to the Catalogue No. ub. EC-43 for details. Hydraulic luids luid Types ny type of hydraulic fluid listed in the table below can be used. etroleum base oils Synthetic fluids Water containing fluids Use fluids equivalent to ISO VG 3 or VG 46. Use phosphate ester or polyol ester fluid. When phosphate ester fluid is used, prefix "-" to the model number because the special seals (fluororubber) are required to be used. Use water-glycol fluid. Note: or use with hydraulic fluids other than those listed above, please consult your Yuken representatives in advance. Recommended Viscosity and Temperatures lways be sure to use hydraulic fluids within the stipulated conditions shown below: Viscosity: to 4 mm /s (77 to 8 SSU), Temperature: - to +7 C ( to 6 ) Control of Contamination Due caution must be paid to maintaining control over contamination of the hydraulic fluids which may otherwise lead to breakdowns and shorten the life of the valve. lease maintain the degree of contamination within NS 638-Grade. Use m or finer line filter. ase lates and Sub-lates When mounting the modular valves, use base plates and sub-plates specified below. If these base plates and the subplates are not used, ensure that the mounting surface has a good machined finish. ase lates MMC-3-T- -/8/9 age 44 Sub-lates DSGM-3-4/8/9 or the details of Sub-late, see the following DSG-3 solenoid operated directional valve catalogues: Catalogue No. ub. EC-43. age Mounting olts 3 Series modular valves are mounted using stud bolts which are supplied in a kit form. When mounting, see the following table for tightening torque. fter the test run, be sure to tighten again firmly within the specified torque. olt Kit Tightening torque Nm (in. lbs.) MK-3- - MK (6-33) No.

6 3 SERIES ssembly / ressure Drop MODULR VLVES ssembly ssembly should be carried out in clean conditions and in accordance with the following procedure. Cautious attention should be paid to ensure that the interface of the valves are clean and free from dirt or other foreign materials. ssembly rocedure: ) Screw-in the four stud bolts, fully into the tapped holes on the mounting surface of the specified base plate, sub-plate or manifold. ) Stack the modular valves and solenoid operated directional valves in accordance with the hydraulic circuit, place the O-ring inserted surface face onto the base plate and make sure that the port arrangement of the modular valves are in the correct position before stacking the valves onto the stud bolts. 3) lign both the end of the valves stacked. 4) Screw-in the four nuts onto the stud bolts and tighten with the specified torque. fter the test run, be sure to re-tighten the nuts firmly within the specified torque. Nut Stud olt Mounting olt Kits Solenoid Operated Directional Valve ase late Modular Valves CUTION Keep all installation holes and surface clean. ailure to do this may cause fire due to oil leakage. efore installing the product, be sure that all specified bolts are tightened to the specified torque levels. Tightening to levels outside specifications may cause improper operation, damage, oil leakage, etc. 3 Series Modular Valves ressure Drop ressure drop curves of the modular valves are those based on viscosity of 3 mm /s (64 SSU) and specific gravity of.8. When using the modular valves in conditions other than the above mentioned, find the appropriate values referring to the following table and formula. or any other viscosity, multiply the factors in the table below. mm /s Viscosity SSU actor or any other specific gravity (G'), the pressure drop ( ') may be obtained from the following formula. '= (G'/.8) No.6

7 3/8, Relief Valves or "" Line : M-3- -3/39 or "" Line : M-3- -3/39 or "" Line : M-3- -3/39 or "&" Lines : MW-3- -3/39 Specifications / Others MODULR VLVES Specifications M-3- M-3- -3/39 M-3- -3/39 MW-3- -3/39-3/39 Max. Operating ressure Ma (SI) Max. low L/min (U.S.GM) 3. (47) 7 (8.) Model Number Designation - M -3 - Special Seals : Special Seals for hosphate Ester Type luids (Omit if not required) Series Number M : Relief Valve for -Line M : Relief Valve for -Line M : Relief Valve for -Line MW : Relief Valve for &-Lines Valve Size. See the "Minimum djustment ressure" of the next page for the item marked.. Design Standards: None... Japanese Standard "JIS" and European Design Standard 9... N. merican Design Standard 3 res. dj. Range Ma (SI) : ( -7 -) H: 3.- (-363) -3 Design Number Design Standard 3 Refer to Instructions The minimum adjustment pressure equals the value obtained from the minimum adjustment pressure characteristics plus the tank line back pressure of the next page. This back pressure should include the value of the T-line pressure drop characteristics of the valves stacked to the base plate side of the modular valve. To make pressure adjustment, loosen the lock nut and turn the pressure adjustment screw clockwise or anticlockwise. or an increase of pressure, turn the screw clockwise. e sure to re-tighten the lock nut firmly after making adjustment to the pressure. In case of a small flow, the setting pressure may become unstable. To avoid this, refer to the minimum flow characteristic curve of the next page and use the valve within a range as shown with. Model Numbers M-3 M-3 M-3 MW-3 Graphic Detailed Graphic T T T T T T T T T T T T No.7

8 3/8, Relief Valves or "","","" and "&" Lines Typical erformance Characteristics MODULR VLVES Hydraulic luid: Viscosity 3 mm /s (64 SSU), Specific Gravity.8 ressure SI Nominal Override Characteristics Ma Min. djiustment ressure SI Min. djustment ressure Ma L/min U.S.GM L/min U.S.GM. Min. low U.S.GM Min. low vs. djustment ressure L/min 6 4 Ma ressure Drop SI Ma..4.3 ressure Drop T-Line: M/M/ MW-3 -Line: M-3. -Line: M-3. T-Line: M-3 -Line: M-3,&-Line: M/M/ MW-3 L/min U.S.GM 3 SI ressure 3 No.8

9 3/8, Relief Valves or "","","" and "&" Lines Installation Drawing / Spare arts List MODULR VLVES MW-3- -3/39 DIMENSIONS IN MILLIMETRES (INCHES) M-3- -3/39 M-3- -3/39 ully Extended 4(8.43) Lock Nut 4(.) Hex. 9 (.7) 9(3.6) 4 (.3) (.98) (.47) ully Extended 34(.8) T T 46 (.8) 7 (.76) T T ressure dj. Screw (for -Line) 4(.) Hex. INC. ully Extended 34(.8) ully Extended 3(.68).8(.7) ressure dj. Screw (for -Line) 4(.) Hex. INC. pprox. Mass...3. kg (7.7 lbs.) or other dimensions, refer to "MW-3" drawing left. M-3- -3/39 ully Extended 4(8.43) 6(.) 7. (.8) (.7) pprox. Mass...4. kg (9.3 lbs.) T T pprox. Mass...3. kg (7.7 lbs.) or other dimensions, refer to "MW-3" drawing left. Spare arts List M-3- -3/39 M-3- -3/39 M-3- -3/ MW-3- -3/39 List of Seals List of Seal Kits Item Name of arts art Numbers Quantity M-3 M-3 M-3 MW-3 M-3 Seal kit Numbers SO-N-4 M-3 KS-M SO-N-6 M-3 7 SO-N-6 MW-3 KS-MW SO-N-6 Note: When ordering seals, please specify the seal kit number from the table right. CUTION When making replacement of seals, please do it carefully after reading through the relevant instructions in the Operator's Manual. No.9

10 or "" or "" or "" 3/8, Reducing Valves Line: Line: Line: MR-3- -3/39 MR-3- -3/39 MR-3- -3/39 Specifications / Others MODULR VLVES Specifications Max. Operating ressure Ma(SI) Max. low L/min (U.S.GM) MR-3- -3/39 MR-3- -3/39 MR-3- -3/39 (363) 7 (8.) In pressure adjustment range "H", if the pressure in the primary side is set above Ma (9 SI) and the pressure in the secondary side is set below Ma (4 SI), the maximum flow is limited to L /min (3. U.S.GM). Model Number Designation - MR -3 - Special Seals : Special Seals for hosphate Ester Type luids (Omit if not required) Series Number MR : Reducing Valve for -Line MR: Reducing Valve for -Line MR: Reducing Valve for -Line Valve Size Design Standards: None... Japanese Standard "JIS" and European Design Standard 9... N. merican Design Standard 3 res. dj. Range Ma (SI) : -7 (4-) H: (-3) -3 Design Number 3 Design Standard Refer to Instructions The minimum adjustment pressure equals the lower limit of either pressure adjustment range (, H) plus the tank line back pressure of the next page. This back pressure should include the value of the T-line pressure drop characteristics of the values stacked to the base plate side of the modular valve. To make pressure adjustment, loosen the lock nut and turn the pressure adjustment screw clockwise or anticlockwise. or an increase of pressure, turn the screw clockwise. e sure to re-tighten the lock nut firmly after making adjustment to the pressure. Model Numbers MR-3 MR-3 MR-3 Graphic T T T Detailed Graphic T T T T T T No.

11 3/8, Reducing Valves or "","" and "" Lines Typical erformance Characteristics MODULR VLVES Hydraulic luid: Viscosity 3 mm /s (64 SSU), Specific Gravity.8 ressure Drop SI 4 3 Ma.3.. ressure Drop &-Line T-Line L/min U.S.GM cu.in./min 3 cm /min 8 ilot low 4 6 ilot low 3 4 Ma 3 3 Differential ressure (rimary pressure - Secondary pressure) SI ressure Drop res. Drop at Spool ully Open (-Line) SI Ma L/min U.S.GM No.

12 3/8, Reducing Valves or "","" and "" Lines Installation Drawing / Spare arts List MODULR VLVES MR-3- -3/39 MR-3- -3/39 DIMENSIONS IN MILLIMETRES (INCHES) 4(.) Lock Nut 4(.) Hex. 9 (.7) T 9(3.6) 4 (.3) T 7(.8) Dia. Through 4 laces (.47) 46 (.8) 7 (.76) M M Thread Size "C" Thd. Rc /4 = /4 S.Tr /4 NT ressure dj. Screw 4(.) Hex. INC. (.7) ully Extended 3(.) ully Extended 33.(9.9).8 (.7) ressure Gauge Connection "C" Thd. 7. (.8) pprox. Mass kg (8.4 lbs.) MR-3- -3/39 ressure Gauge Connection "C" Thd. 47. (.87) ully Extended 33.(9.) T T pprox. Mass kg (8.4 lbs.) or other dimensions, refer to "MR-3" drawing above. Spare arts List MR-3- -3/39 MR-3- -3/ MR-3- -3/39 List of Seals Item Name of arts art Numbers Qty SO-N-4 SO-N-6 SO-N-6 SO-N-8 SO-N-6 Remarks Included in Seal Kit Kit No.: KS-MR-3-3 CUTION When making replacement of seals, please do it carefully after reading through the relevant instructions in the Operator's Manual. No.

13 Low ressure Setting Type 3/8, Reducing Valves or "" Line: MRL-3-/8/9 or "" Line: MRL-3-/8/9 or "" Line: MRL-3-/8/9 Specifications / Others MODULR VLVES Specifications Max. Operating ressure Ma (SI) res. dj. Range Ma (SI) Max. low L/min (U.S.GM) MRL-3-/8/9 MRL-3-/8/9 MRL-3-/8/9 7 ().-6. (9-94) (3.) When pressure setting is less than.8 Ma (6 SI), maximum pressure decreases. See "Min. djustment ressure vs. Max. low" on the next page for the appropriate range. Model Number Designation - MRL -3 Special Seals Series Number Valve Size - Design Number Design Standard : Special Seals for hosphate Ester Type luids (Omit if not required) MRL : Low ressure Setting Type Reducing Valve for -Line MRL : Low ressure Setting Type Reducing Valve for -Line MRL : Low ressure Setting Type Reducing Valve for -Line 3 Refer to Design Standards: None... Japanese Standard "JIS" 8... European Design Standard 9... N. merican Design Standard Instructions If there is a pressure in drain line, it is added to the secondary setting pressure. Hence, drain line must be connected to tank directly with a low back pressure close to atmospheric pressure. Model Numbers MRL-3 V Graphic DR V Detailed Graphic DR To make pressure adjustment, loosen the lock nut and turn the pressure adjustment handle clockwise or anticlockwise. or an increase of pressure, turn the handle clockwise. e sure to re-tighten the lock nut firmly after making adjustment to the pressure. MRL-3 MRL-3 V V T T DR DR V V T T T T DR DR T T T No.3

14 Low ressure Setting Type 3/8, Reducing Valves or "", "" and "" Lines Typical erformance Characteristics MODULR VLVES Hydraulic luid: Viscosity 3 mm /s (64 SSU), Specific Gravity.8 ressure Drop SI res. Drop at Spool ully Open (-Line) Ma L/min U.S.GM ressure Drop SI ressure Drop Ma.. &-Line T-Line 3 4 L/min U.S.GM Min. djustment res. SI Min. djustment ressure vs. Max. low Ma L/min U.S.GM No.4

15 Low ressure Setting Type 3/8, Reducing Valves or "", "" and "" Lines Installation Drawing MODULR VLVES MRL-3-/8/9 MRL-3-/8/9 47 (.8) 4 (.) 4 Dia. (.77) Vent ort "V" "D" Thd. Lock Nut 4(.) Hex. 8 Design Only 6 (.4) 9 (.7) 9(3.6) 4 (.3) T T 7(.8) Dia. Through 4 laces (.47) 46 (.8) 7(.76) Drain ort "DR" "C" Thd. ully Extended.(.96) 3 (.9) ully Extended 9.(.).8 (.7) ressure dj. Handle INC. ressure Gauge Connection "E" Thd. 7. (.8) (.7) pprox. Mass...4. kg (9.9 lbs.) MRL -3- MRL -3-8 MRL -3-9 Thread Size "C" Thd. "D" Thd. "E" Thd. Rc /4 /4 S. /4 NT Rc /8 /8 S. /8 NT Rc /4 /4 S.Tr /4 NT DIMENSIONS IN MILLIMETRES (INCHES) MRL-3-/8/9 ressure Gauge Connection "E" Thd. 4 (.3) T ully Extended 9.(.) 8 (4.) T Vent ort "V" "D" Thd. Drain ort "DR" "C" Thd. pprox. Mass...4. kg (9.9 lbs.) or other dimensions, refer to "MRL-3" drawing above. No.

16 Low ressure Setting Type 3/8, Reducing Valves or "", "" and "" Lines Spare arts List MODULR VLVES Spare arts List MRL-3-/8/9 MRL-3-/8/9 T T MRL-3-/8/ List of Seals Item Name of arts art Numbers Qty. Remarks onded Seal SO-N-6 SO-N-6 SO-N-4 SO-N- SO-N-3 SG--/8 Included in Seal Kit Kit No.:KS-MRL-3- Note: No bonded seal are included in seal kits. CUTION When making replacement of seals, please do it carefully after reading through the relevant instructions in the Operator's Manual. No.6

17 3/8, Sequence Valves or "" Line: MH-3- -/9 3/8, Counterbalance Valves or "" Line: MH-3- -/9 or "" Line: MH-3- -/9 Specifications / Others MODULR VLVES Specifications MH-3- -/9 MH-3- MH-3- -/9 -/9 Max. Operating ressure Ma (SI) Max. low L/min (U.S.GM) (363) (3.) Max. ree low L/min (U.S.GM) 7 (8.) MH-3 Model Number Designation - MH -3 -C Special Seals Series Number Valve Size res. dj. Range Ma (SI) MH/ MH-3 - Design Number Design Standard : MH : Sequence Valve for -Line Special Seals for hosphate Ester Type luids (Omit MH: Counterbalance Valve for -Line if not required) MH: Counterbalance Valve for -Line 3 N: -.8 ( -6) :.8-3. (6-) : 3.-7 (-) C: 7-4 (-3) Refer to. See the "Minimum djustment ressure" of the next page for the item marked.. Design Standards: None... Japanese Standard "JIS" and European Design Standard 9... N. merican Design Standard Instructions The minimum adjustment pressure equals the value obtained from the minimum adjustment pressure characteristics plus the tank line back pressure of the next page. This back pressure should include the value of the T-line pressure drop characteristics of the valves stacked to the base plate side of the modular valve. To make pressure adjustment, loosen the lock nut and turn the pressure adjustment screw clockwise or anticlockwise. or an increase of pressure, turn the screw clockwise. e sure to re-tighten the lock nut firmly after making adjustment to the pressure. Model Numbers MH-3 MH-3 MH-3 Graphic Detailed Graphic T T T T T T T T T No.7

18 3/8, Sequence Modular Valves or "" Line 3/8, Counterbalance Modular Valves or "" and "" Lines Typical erformance Characteristics MODULR VLVES Hydraulic luid: Viscosity 3 mm /s (64 SSU), Specific Gravity.8 Min. djustment ressure SI Min. djustment ressure Ma MH/MH/MH L/min ressure Drop SI 4 3 Ma ressure Drop for ree low MH/MH L/min U.S.GM U.S.GM ressure Drop SI ressure Drop SI Ma Ma. MH-3....,-Line. T-Line 3 4 L/min ressure Drop ressure Drop MH/MH-3 -Line:MH-3 -Line:MH-3 T-Line:MH-3 -Line T-Line:MH L/min U.S.GM U.S.GM No.8

19 3/8, Sequence Valves or "" Line 3/8, Counterbalance Valves or "" and "" Lines Installation Drawing / Spare arts List MODULR VLVES MH-3- -/9 4 (.) Lock Nut 4(.) Hex. 9(3.6) 9(.7) T 4 (.3) T 7(.8) Dia. Through 4 laces (.47) 46 (.8) 7(.76) ressure dj. Screw 4(.6) Hex. Soc. INC. ully Extended 34(.8) ully Extended 4(9.3).8 (.7) (.7) MH-3- -/9 7. (.8) DIMENSIONS IN MILLIMETRES (INCHES) pprox. Mass...3. kg (7.7 lbs.) MH-3- -/9 7 (.67) ully Extended 8(8.98) ully Extended 34(.8) 4 (.7) T T T ully Extended 8(8.98) T 7 (.67) pprox. Mass kg (7.7 lbs.) pprox. Mass kg (7.7 lbs.) or other dimensions, refer to "MH-3" drwaing above. Spare arts List MH-3- -/ CUTION When making replacement of seals, please do it carefully after reading through the relevant instructions in the Operator's Manual. List of Seals Item Name of arts art Numbers Qty SO-N-4 SO-N-6 SO-N-9 SO-N-3 Remarks Included in Seal Kit Kit No.:KS-MH-3- MH-3- -/9 MH-3- -/ No.9

20 ressure and Temperature Compensated 3/8, low Control (and Check) Valves or "" Line: M-3-/9 or "" Line: M-3- -/9 or "" Line: M-3- -/9 or "&" Lines: MW-3- -/9 Specifications / Others MODULR VLVES Specifications Max. Operating ressure Ma (SI) Max. Metred low L/min (U.S.GM) Max. ree low L/min (U.S.GM) M-3-/9 M-3- M-3- -/9 MW-3- -/9 -/9 6 (3) (3.) 7 (8.) Model Number Designation - M Special Seals Series Number : M : low Control Valve for -Line Special Seals for hosphate Ester M : low Control and Check Valve for -Line Type luids (Omit M : low Control and Check Valve for -Line if not required) MW : low Control and Check Valve for &-Lines -3 -X Valve Size Design Standards: None... Japanese Standard "JIS" and European Design Standard 9... N. merican Design Standard 3 Direction of low X: Metre-out Y: Metre-in - Design Number Design Standard Refer to Instructions To make flow rate adjustment, loosen locking screw for the dial and turn the flow adjustment dial clockwise or anti-clockwise. or a decrease of flow, turn the dial clockwise. e sure to re-tighten the locking screw firmly after the adjustment of the flow rate. Model No. Graphic Detailed Graphic M-3 Model No. T T Metre-out T Model No. Graphic Metre-in Detailed Graphic M-3-X M-3-Y T T T T T T M-3-X M-3-Y T T T T T T MW-3-X MW-3-Y T T T T T T No.

21 ressure and Temperature Compensated 3/8, low Control and Check Valves or "", "", "" and "&" Lines Typical erformance Characteristics MODULR VLVES Hydraulic luid: Viscosity 3 mm /s (64 SSU), Specific Gravity.8 Min. Metred low Differential ressure Min. Required ressure Difference SI Ma 6. M-3..8 M -3 W L/min 3 cu.in./min cm /min Min. Metred low Metred low vs. Dial osition SI Ma (ully Open) Turn of low dj. Dial 6 Ma SI Differential ressure U.S.GM ressure Drop ressure Drop U.S.GM SI SI 4 3 ressure Drop for ree low Ma Ma Metred low vs. Differential ressure L/min U.S.GM 8 ressure Drop L/min -Line:M-3 -Line:M-3 T-Line:M -3 &-Line:M-3 T-Line:M-3 7 L/min. 7. U.S.GM 6 Ma U.S.GM Metred low vs. Viscosity L/min Differential ressure SI mm /s 4 Viscosity 6 7 SSU No.

22 ressure and Temperature Compensated 3/8, low Control (and Check) Valves or "", "", "" and "&" Lines Installation Drawing MODULR VLVES M-3-/9 (.9) 9(3.6) 9(.7) 4 (.3) (.47) 7(.8) Dia. Through 4 laces 8 9 T T 46 (.8) 7(.76) low dj. Dial ully Extended 33(9.7) INC. 3(.6) Dia. ully Extended 6(6.3).8 (.7) LOCK (.7) 33(.3) 3 4 Locking Screw (.8) Hex. Soc. pprox. Mass...4. kg (9.3 lbs.) MW-3- X-/9 Y.4 (.84) 3(.6) Dia. low dj. Dial (for -Line) INC. ully Extended 3 (6.) 9(3.6) 9(.7) 4 (.3) T T ully Extended 36(4.7) (.47) 46(.8) 7(.8) Dia. Through 4 laces 7(.76).8 (.7) DIMENSIONS IN MILLIMETRES (INCHES) low dj. Dial (for -Line) INC. (.7) LOCK MW-3-X (.3) MW-3-Y (.87) Locking Screw (.8) Hex. Soc. pprox. Mass... kg (. lbs.) M-3- X-/9 Y M-3- X-/9 Y ully Extended 63(.3) ully Extended 3 (6.) 6 (.) ully Extended 63(.3) T T T T pprox. Mass...4. kg (9. lbs.) pprox. Mass...4. kg (9. lbs.) or other dimensions, refer to "MW-3" drawing above. No.

23 Spare arts List M-3-/9 ressure and Temperature Compensated 3/8, low Control (and Check) Valves or "", "", "" and "&" Lines Spare arts List MODULR VLVES M-3- X-/9 Y M-3- X-/9 Y MW-3- X-/9 Y List of Seals Item Name of arts art Numbers Quantity M-3 M-3 M-3 MW-3 ack Up Ring SO--6 6 SO-N-6 7 SO-N-4 8 SO-N-8 Note: When ordering seals, please specify the seal kit number from the table right. List of Seal Kits Seal Kit Numbers M-3 KS-M-3- M-3 M-3 KS-M-3- MW-3 KS-MW-3- CUTION When making replacement of seals, please do it carefully after reading through the relevant instructions in the Operator's Manual. No.3

24 Temperature Compensated 3/8, Throttle and Check Valves or "" Line: MST-3-X-/9 or "" Line: MST-3-X-/9 or "&" Lines: MSTW-3-X-/9 Specifications / Others MODULR VLVES Specifications MST-3-X-/9 MST-3-X-/9 MSTW-3-X-/9 Max. Max. Operating Differential ressure ressure Ma (SI) (363) Ma (SI) (363) Max. Metred low L/min (U.S.GM) 7 (8.) Min. Metred low L/min (U.S.GM) (.3) { (.6)} Max. ree low L/min (U.S.GM) 7 (8.) The figures in parentheses are the values when the differential pressure is less than 3. Ma ( SI). Model Number Designation - MST Special Seals Series Number -3 -X Valve Size Direction of low - Design Number Design Standard : Special Seals for hosphate Ester Type luids (Omit if not required) MST : Temperature Compensated Throttle and Check Valve for -Line MST : Temperature Compensated Throttle and Check Valve for -Line MSTW : Temperature Compensated Throttle and Check Valve for &-Lines 3 X:Metre-out Refer to Design Standards: None... Japanese Standard "JIS" and European Design Standard 9... N. merican Design Standard Instructions To make flow rate adjustment, loosen locking screw for the dial and turn the flow adjustment dial clockwise or anti-clockwise. or a decrease of flow, turn the dial clockwise. e sure to re-tighten the locking screw firmly after the adjustment of the flow rate. Model No. MST-3-X Graphic Metre-out Detailed Graphic T T T MST-3-X T T T MSTW-3-X T T T No.4

25 Temperature Compensated 3/8, Throttle and Check Valves or "", "" and "&" Lines Typical erformance Characteristics MODULR VLVES Hydraulic luid: Viscosity 3 mm /s (64 SSU), Specific Gravity.8 ressure Drop SI 3 Ma.... ressure Drop Line:MST-3 -Line:MST-3 -Line T-Line L/min U.S.GM 7... L/min 7 6 Metred low vs. Dial osition : Differential ressure Ma(SI) : 4(3) : (363) U.S.GM : 7() : (73) : (9) ressure Drop SI Ma ressure Drop for ree low Throttle ully Open Throttle Closed L/min. : (4) :.(7) Turn of low dj. Dial (ully Open) Metred low vs. Viscosity ressure Drop SI U.S.GM ressure Drop at Throttle ully Open Ma L/min U.S.GM L/min mm /s Viscosity SSU U.S.GM No.

26 Temperature Compensated 3/8, Throttle and Check Valves or "", "" and "&" Lines Installation Drawing / Spare arts List MODULR VLVES MSTW-3-X-/9.4 (.84) (.7) low dj. Dial (for -Line) INC. 3(.6) Dia. 33 (.3) (.7) 4 (.3) T 9(3.6) T ully Extended 6(4.7) ully Extended 66(.47) DIMENSIONS IN MILLIMETRES (INCHES) 7(.8) Dia. Through 4 laces (.47) 46 (.8) 7(.76).8 (.7) low dj. Dial (for -Line) INC. LOCK Locking Screw (.8) Hex. Soc. pprox. Mass kg (8. lbs.) MST-3-X-/9 ully Extended (8.3) ully Extended 6(4.7) 8 9 T T pprox. Mass...3. kg (7.7 lbs.) or other dimensions, refer to "MSTW-3" drawing left. MST-3-X-/9 (.97) T T ully Extended (8.3) pprox. Mass...3. kg (7.7 lbs.) or other dimensions, refer to "MSTW-3" drawing left. 8 9 Spare arts List MST-3-X-/9 MST-3-X-/ MSTW-3-X-/9 List of Seals Item Name of arts art Numbers Quantity MST-3 MST-3 ack Up Ring 9-VK49-3 SO-N-7 4 SO-N-4 SO-N-4 MSTW-3 Note: When ordering seals, please specify the seal kit number from the table right. List of Seal Kits Seal Kit Numbers MST-3 KS-MST-3- MST-3 MSTW-3 KS-MSTW-3- CUTION When making replacement of seals, please do it carefully after reading through the relevant instructions in the Operator's Manual. No.6

27 3/8, Throttle Valves or "" Line: MS-3-3/39 Specifications / Others MODULR VLVES Specifications Max. Operating ressure Ma (SI) Max. low L/min (U.S.GM) MS-3-3/39 (363) 7 (8.) Maximum flow decreases when the differential pressure is less than Ma (4 SI). See "ressure Drop at Throttle ully Open". Model Number Designation - MS -3 Special Seals : Special Seals for hosphate Ester Type luids (Omit if not required) Series Number MS : Throttle Valve for -Line Valve Size -3 Design Number Design Standards: None... Japanese Standard "JIS" and European Design Standard 9... N. merican Design Standard 3 3 Design Standard Refer to Graphic Symbol T Detailed Graphic Symbol Typical erformance Characteristics T T Hydraulic luid: Viscosity 3 mm /s (64 SSU), Specific Gravity.8 ressure Drop SI U.S.GM Ma.. ressure Drop Line &T-Line L/min U.S.GM Metred low vs. Dial osition : Differential ressure Ma (SI) L /min =(363) 7 =(9) 6 =4(3) 4 =(4) =(73) 3 =3(44) =(9) =(4) =.(7) Turn of low dj. Dial (ully Open) ressure Drop SI ressure Drop at Throttle ully Open Ma L/min U.S.GM Instructions To make flow rate adjustment, loosen locking screw for the dial and turn the flow adjustment dial clockwise or anti-clockwise. or a decrease of flow, turn the dial clockwise. e sure to re-tighten the locking screw firmly after the adjustment of the flow rate. No.7

28 3/8, Throttle Valves or "" Line Installation Drawing / Spare arts List MODULR VLVES MS-3-3/39 DIMENSIONS IN MILLIMETRES (INCHES) 9 (.7) 9(3.6) 4 (.3) 7(.8) Dia. Through 4 laces (.47) 8 9 T T ully Extended 7(4.) ully Extended 8(7.3) low dj. Dial INC. (.7) 33 (.3) 3. (.3) 46 (.8) 7(.76) 3 Dia. (.6).8 (.7) Locking Screw (.8) Hex. Soc. pprox. Mass...3. kg (6.6 lbs.) Spare arts List MS-3-3/ List of Seals Item Name of arts art Numbers Qty. 8 9 ack Up Ring 9-VK49- SO-N-7 SO-N-4 SO-N-4 Remarks Included in Seal Kit Kit No.: KS-MS-3-3 CUTION When making replacement of seals, please do it carefully after reading through the relevant instructions in the Operator's Manual. No.8

29 3/8, Check and Throttle Valves or "" Line: MSC-3-/9 Specifications / Others MODULR VLVES Specifications Max. Operating ressure Ma (SI) Max. low L/min (U.S.GM) MSC-3-/9 (363) 7 (8.) Maximum flow decreases when the differential pressure is less than.8 Ma ( SI). See "ressure Drop at Throttle ully Open". Model Number Designation - MSC -3 Special Seals Series Number Valve Size - Design Number Design Standard : Special Seals for hosphate Ester Type luids (Omit if not required) MSC : Check and Throttle Valve for -Line Design Standards: None... Japanese Standard "JIS" and European Design Standard 9... N. merican Design Standard 3 Refer to Graphic Symbol T Detailed Graphic Symbol Typical erformance Characteristics ressure Drop Hydraulic luid: Viscosity 3 mm /s (64 SSU), Specific Gravity.8 ressure Drop SI Ma SI. -Line. -Line T-Line L/min ressure Drop ressure Drop at Throttle ully Open Ma T T L/min U.S.GM U.S.GM Metred low vs. Dial osition : Differential ressure Ma (SI) =(363) =(9) =4(3) U.S.GM L/min =(4) =(73). 4 =3(44) 3 =(9). =(4) =.(7) Dial osition (ully Open) Instructions To make flow rate adjustment, loosen locking screw for the dial and turn the flow adjustment dial clockwise or anticlockwise. or a decrease of flow, turn the dial clockwise. e sure to re-tighten the locking screw firmly after the adjustment of the flow rate. No.9

30 3/8, Check and Throttle Valves or "" Line Installation Drawing / Spare arts List MODULR VLVES MSC-3-/9 DIMENSIONS IN MILLIMETRES (INCHES) 9 (.7) 9(3.6) 4 (.3) (.47) 7(.8) Dia. Through 4 laces 6. (.6) 8 9 T T 46 (.8) 7(.76) ully Extended 9.7 (4.3).8 (.7) ully Extended 8.7 (7.9) low dj. Dial INC. LOCK (.7) 7. (.8) 3 Dia. (.6) 3 4 Locking Screw (.8) Hex. Soc. pprox. Mass...3. kg (6.6 lbs.) Spare arts List MSC-3-/ List of Seals Item Name of arts art Numbers Qty. 3 4 ack Up Ring 9-VK49- SO-N-7 SO-N-4 SO-N-4 Remarks Included in Seal Kit Kit No.: KS-MS-3-3 CUTION When making replacement of seals, please do it carefully after reading through the relevant instructions in the Operator's Manual. No.3

31 3/8, Throttle and Check Valves or "" Line: MS-3- -4/49 or "" Line: MS-3- -4/49 or "&" Lines: MSW-3- -4/49 Specifications / Others MODULR VLVES Specifications Max. Operating ressure Ma (SI) Max. low L/min (U.S.GM) MS-3- -4/49 MS-3- -4/49 MSW-3- -4/49 3. (47) (3.7) Model Number Designation - Special Seals MSW -3 Series Number Valve Size -X Direction of low -4 Design Number Design Standard : Special Seals for hosphate Ester Type luids (Omit if not required) MS : Throttle and Check Valve for -Line MS : Throttle and Check Valve for -Line MSW : Throttle and Check Valve for &-Lines 3 X: Metre-out Y: Metre-in 4 Refer to Design Standards: None... Japanese Standard "JIS" and European Design Standard 9... N. merican Design Standard Instructions To make flow rate adjustment, loosen locking screw for the dial and turn the flow adjustment dial clockwise or anti-clockwise. or a decrease of flow, turn the dial clockwise. e sure to re-tighten the locking screw firmly after the adjustment of the flow rate. Model No. Graphic Metre-out Detailed Graphic Model No. Graphic Detailed Graphic Metre-in MS-3-X MS-3-Y T T T T T T MS-3-X MS-3-Y T T T T T T MSW-3-X MSW-3-Y T T T T T T No.3

32 3/8, Throttle and Check Valves or "", "" and "&" Lines Typical erformance Characteristics MODULR VLVES Hydraulic luid: Viscosity 3 mm /s (64 SSU), Specific Gravity.8 ressure Drop SI 4 4 Ma ressure Drop Line:MS-3 -Line:MS-3 T-Line -Line 8 L /min U.S.GM ressure Drop SI ressure Drop for ree low Ma...8 Throttle Closed.6.4. Throttle ully Open L /min 3 U.S.GM ressure Drop ressure Drop at Throttle ully Open SI Ma L/min 3 U.S.GM Metred low vs Dial osition SI 3 Ma :7() :4(3) : (363) :3 (43) 3 4 : Differential ressure Ma (SI) :(9) :(4) :.(7) 6 7 Turn of low dj Dial 8 :(73) 9 ully Open No.3

33 3/8, Throttle and Check Valves or "", "" and "&" Lines Installation Drawing / Spare arts List MODULR VLVES MSW-3- X-4/49 Y.4 (.84) (.7) low dj. Dial (for -Line) INC. 3(.6) Dia 9 (.7) T 9(3.6) 4 (.3) ully Extended 9. (3.6) ully Extended T 37 (9.33) DIMENSIONS IN MILLIMETRES (INCHES) 7(.8) Dia. Through 4 laces (.47) 46 (.8) 7 (.76).8 (.7) low dj. Dial (for -Line) INC. LOCK MS-3- X-4/49 Y ully Extended 93. (7.6) ully Extended 9. (3.6) T MS-3- X-4/49 Y T pprox. Mass...3. kg (7.7 lbs.) or other dimensions, refer to "MSW-3" drawing left. ully Extended 93. (7.6) 48 (.89) 4 (.94) Locking Screw (.8) Hex. Soc. pprox. Mass kg (8. lbs.) T T pprox. Mass...3. kg (7.7 lbs.) or other dimensions, refer to "MSW-3" drawing left. Spare arts List MS-3- X-4/49 Y MS-3- X-4/49 Y 9 MSW-3- X-4/49 Y CUTION When making replacement of seals, please do it carefully after reading through the relevant instructions in the Operator's Manual. List of Seals Item Name of arts art Numbers Quantity MS-3 MS-3 MSW-3 9 ack Up Ring SO--8 SO-N-8 SO-N-4 SO-N-8 Note: When ordering seals, please specify the seal kit number from the table right. List of Seal Kits Seal Kit Numbers MS-3 KS-MS-3-4 MS-3 MSW-3 KS-MSW-3-4 No.33

34 3/8, Check Valves or "" Line: MC-3- -/9 or "" Line: MC-3- -/9 or "" Line: MC-3- -/9 or "T" Line: MCT-3- -/9 Specifications / Others MODULR VLVES Specifications MC-3- MC-3- -/9 MC-3- -/9 MCT-3- -/9 -/9 Max. Operating ressure Ma (SI) Max. low L/min (U.S.GM) (363) 7 (8.) Model Number Designation - MC -3 Cracking ressure Special Seals Series Number Valve Size Ma(SI) MC : Check Valve for -Line : Special Seals for hosphate :.3() MC: Check Valve for -Line Ester Type luids 3 (Omit if not required) MC: Check Valve for -Line :.(9) MCT : Check Valve for T-Line Design Standards: None... Japanese Standard "JIS" and European Design Standard 9... N. merican Design Standard - - Design Number Design Standard Refer to Typical erformance Characteristics Hydraulic luid: Viscosity 3 mm /s (64 SSU), Specific Gravity.8 Model No. Graphic Detailed Graphic ressure Drop SI ressure Drop or ree low Ma L/min MC -3- MC MCT -3- MC -3- MC MCT -3- MC-3 MCÁ-3 MC-3 MCT-3 T T T T T T T T T T T T ressure Drop SI Ma U.S.GM ressure Drop Line:MC/MCT-3 -Line:MC-3 &-Line:MC-3 T-Line:MC/MC-3 -Line:MC/MC/MCT-3 -Line:MCT-3 T-Line:MC-3 7 L/min Instructions Tank Line Used Check valve function of MCT-3 is included in T - Line. Therefore, the tank line for a circuit that uses this valve must be T -line U.S.GM No.34

35 MC-3- -/9 9 (.7) 7(.8) Dia. Through 4 laces 9(3.6) 4 (.3) T T (.47) 46 (.8) 7 (.76) 3/8, Throttle and Check Valves or "", "", "" and "T" Lines Installation Drawing / Spare arts List MC-3- -/9 MC-3- -/9 9 (.7) T 9(3.6) 4 (.3) T 7(.8) Dia. Through 4 laces (.47) 46 (.8) 7 (.76) MCT-3- -/9 (Check valve is included) 9 (.7) T MODULR VLVES 9(3.6) 4 (.3) T 7(.8) Dia. Through 4 laces (.47) 46 (.8) 7 (.76) 3 (.9) (3.94).8 (.7) 6 (.36) 74(6.8).8 (.7) 44 (.73) 7(4.6) (.7) (.7) (.7).8 (.7) pprox. Mass.... kg (. lbs.) pprox. Mass...3. kg (7.7 lbs.) DIMENSIONS IN MILLIMETRES (INCHES) pprox. Mass....8 kg (6. lbs.) Spare arts List MC-3- -/9 CUTION When making replacement of seals, please do it carefully after reading through the relevant instructions in the Operator's Manual. MCT-3- -/ List of Seals List of Seals Item 8 9 Name of arts art Numbers Qty. SO-N-4 SO-N-4 Remarks Included in Seal Kit Kit No.: KS-MC-3- Item 7 8 Name of arts art Numbers Qty. SO-N-4 SO-N- Remarks Included in Seal Kit Kit No.: KS-MC-3- MC-3- -/ MC-3- -/9 List of Seals Item Name of arts art Numbers Qty. 6 7 SO-N-4 SO-N-4 Remarks Included in Seal Kit Kit No.: KS-MC-3- No.3

36 3/8, Check Valves or "&T" Lines: MCT-3- -T -/9 Specifications / Others MODULR VLVES Specifications MCT-3- -T -/9 Max. Operating ressure Ma (SI) Max. low L/min (U.S.GM) (363) 7 (8.) Model Number Designation - MCT -3 Special Seals Series Number Valve Size - Cracking res. of -Line Ma(SI) -T Cracking res. of T-Line Ma(SI) - Design Number Design Standard : Special Seals for hosphate Ester Type luids (Omit if not required) MCT : Check Valve for &T-Lines 3 :.3() :.(9) T :.3() T :.(9) Refer to Design Standards: None... Japanese Standard "JIS" and European Design Standard 9... N. merican Design Standard Typical erformance Characteristics Hydraulic luid: Viscosity 3 mm /s (64 SSU), Specific Gravity.8 Graphic Symbol ressure Drop SI ressure Drop or ree low Ma MCT-3- -T MCT-3--T MCT-3- -T MCT-3--T 7 L/min U.S.GM T Detailed Graphic Symbol T T Instructions Tank Line Used Check valve function of Tank Line is included in T -Line. Therefore, the tank line for a circuit that uses this valve must be T -line. ressure Drop SI Ma.. ressure Drop 3 4 6,-Line 7 L/min U.S.GM No.36

37 3/8, Check Valves or "&T" Lines Instllations Drawing / Spare arts List MODULR VLVES MCT-3- -T -/9 9 (.7) (Check valve is included) T 9(3.6) 4 (.3) T (.47) 46 (.8) 7(.8) Dia. Through 4 laces 7 (.76) 6 (.36) 33 (.4).8 (.7) (.7) DIMENSIONS IN MILLIMETRES (INCHES) pprox. Mass...7 kg (6. lbs.) Spare arts List MCT-3- -T -/ Y Y Y-Y Section List of Seals Item 9 Name of arts art Numbers Qty. SO-N-4 SO-N- Remarks Included in Seal Kit Kit No.: KS-MCT-3- CUTION When making replacement of seals, please do it carefully after reading through the relevant instructions in the Operator's Manual. No.37

38 3/8, nti-cavitation Valves MC-3-/9 Specifications / Others MODULR VLVES Specifications MC-3-/9 Max. Operating ressure Ma (SI) Max. low L/min (U.S.GM) (363) 7 (8.) Model Number Designation - MC -3 Special Seals Series Number Valve Size - Design Number Design Standard : Special Seals for hosphate Ester Type luids (Omit if not required) MC : nti-cavitation Valve 3 Refer to Design Standards: None... Japanese Standard "JIS" and European Design Standard 9... N. merican Design Standard ressure Drop Hydraulic luid: Viscosity 3 mm /s (64 SSU), Specific Gravity.8 Graphic Symbol ressure Drop SI Ma. 3 &-Line &T-Line L/min T Detailed Graphic Symbol U.S.GM T T MC-3-/9 9(3.6) 9(.7) 4 (.3) 7(.8) Dia Through 4 laces (.47) Spare arts List MC-3-/ T T 46 (.8) 7(.76) 48 (.89) (.9) (.7).8 (.7) List of Seals Item Name of arts art Numbers Qty. SO-N-4 SO-N- Remarks Included in Seal Kit Kit No.: KS-MC-3- DIMENSIONS IN MILLIMETRES (INCHES) pprox. Mass kg (8.4 lbs.) CUTION When making replacement of seals, please do it carefully after reading through the relevant instructions in the Operator's Manual. No.38

39 3/8, ilot Operated Check Valves or "" Line: M-3- -/9 or "" Line: M-3- -/9 or "&" Lines: MW-3- -/9 Specifications / Model Number Designation MODULR VLVES Specifications M-3- M-3- -/9 MW-3- -/9 -/9 Max. Operating ressure Ma (SI) Max. low L/min (U.S.GM) (363) 7 (8.) Model Number Designation - M -3 Special Seals Series Number Valve Size - Cracking ressure Ma (SI) - Design Number Design Standard : Special Seals for hosphate Ester Type luids (Omit if not required) M : ilot Operated Check Valve for -Line M : ilot Operated Check Valve for -Line MW : ilot Operated Check Valve for &-Lines 3 :. (9) 4:.4 (8) Refer to Design Standards: None... Japanese Standard "JIS" and European Design Standard 9... N. merican Design Standard Model No. Graphic Detailed Graphic M-3 T T T M-3 T T T MW-3 T T T No.39

40 3/8, ilot Operated Check Valves or "", "" and "&" Lines Typical erformance Characteristics MODULR VLVES Hydraulic luid: Viscosity 3 mm /s (64 SSU), Specific Gravity.8 ressure Drop SI 4 3 Ma.4.3. ressure Drop -Line:M-3 -Line:M-3 T-Line. -Line L/min ressure Drop ressure Drop or Reversed Controlled low SI 4 3 Ma L/min U.S.GM...7. U.S.GM ressure Drop SI ressure Drop or ree low Ma L/min M -3-4 M -3- Min. ilot ressure () SI Ma Min. ilot ressure M -3-4 M -3- Ma...7. U.S.GM 33 SI Supply ressure () No.4

41 3/8, ilot Operated Check Valves or "", "" and "&" Lines Installation Drawing / Spare arts List MODULR VLVES M-3- -/9 M-3- -/9 MW-3- -/9 9 (.7) 9(3.6) 4 (.3) 7(.8) Dia. Through 4 laces (.47) DIMENSIONS IN MILLIMETRES (INCHES) T T 46 (.8) 7 (.76) 6 (.36) 74(6.8).8 (.7) (.7) pprox. Mass...3. kg (7.7 lbs.) Spare arts List M-3- -/9 M-3- -/ MW-3- -/9 List of Seals Item 8 9 Name of arts art Numbers Qty. SO-N-4 SO-N-4 Remarks Included in Seal Kit Kit No.: KS-M-3- CUTION When making replacement of seals, please do it carefully after reading through the relevant instructions in the Operator's Manual. No.4

42 End lates or 3/8 Modular Valve MDC-3- -/9 Specifications / Others MODULR VLVES locking plates are used for auxiliary mounting surfaces or for closing unnecessary circuit. ypass plates are used for one-way flow circuit that requires no solenoid operated directional valves. Specifications MDC-3- -/9 Max. Operating ressure Ma (SI) Max. low L/min (U.S.GM) (363) 7 (8.) Model Number Designation - MDC -3 Special Seals : Special Seals for hosphate Ester Type luids (Omit if not required) Series Number Valve Size - Type of late - Design Number : locking late MDC: End late 3 : ypass late Design Standard None: Japanese Standard "JIS" and European Design Standard 9: N. merican Design Standard ressure Drop Hydraulic luid: Viscosity 3 mm /s (64 SSU), Specific Gravity.8 Model No. Graphic Detailed Graphic xressure Drop SI 4 3 Ma.3.. MDC-3- T T MDC-3- T L/min Line T-Line U.S.GM MDC-3- MDC-3- -/9 9 (.7) T T T 9(3.6) 4 (.3) for ort (SO-N-4: cs.) (.47) 7(.8) Dia. Through (.43) Dia. Spotface 4 laces T T 7 (.6) 46 (.8) 7 (.76) 8 (.).8 (.7) pprox. Mass :. kg (.6 lbs.) DIMENSIONS IN MILLIMETRES (INCHES) No.4

43 Connecting lates or 3/8 Modular Valve MDS-3-/9 Specifications / Others MODULR VLVES Specifications MDS-3-/9 Max. Operating ressure Ma (SI) Max. low L/min (U.S.GM) (363) 7 (8.) Model Number Designation - MDS -3 Special Seals Series Number Valve Size - Design Number Design Standard : Special Seals for hosphate Ester Type luids (Omit if not required) ressure Drop MDS : Connecting late 3 Hydraulic luid: Viscosity 3 mm /s (64 SSU), Specific Gravity.8 None: Japanese Standard "JIS" and European design Standard 9 : N.merican Design Standard Graphic Symbol ressure Drop SI Ma..,, &T-Line L/min T Detailed Graphic Symbol U.S.GM T T MDS-3-/9 for ort (SO-N-4: cs.) 4(.7) (.9) 6 (.63) 9 (.7) 9(3.6) 4 (.3).(.4) 7(.8) Dia. Through 4 laces.(.89) (.47) (.9) (.7) 4 (.7) 3(.38) T T 46 (.8) 7(.76) -Line ressure Gauge Connection "C" Thd. T -Line ressure Gauge Connection "C" Thd. 3 (.9) (3.94).8 (.7) pprox. Mass... kg (. lbs.) -Line ressure Gauge Connection "C" Thd. -Line ressure Gauge Connection "C" Thd. MDS-3- MDS-3-9 iping Size "C" Thd. Rc /4 = /4 S.Tr /4 NT DIMENSIONS IN MILLIMETRES (INCHES) No.43

44 ase lates or 3/8 Modular Valve MMC-3- -/8/9 Specifications / Others MODULR VLVES Specifications Max. Operating ressure Ma (363 SI) Model Number Designation MMC Series Number -3 late Size -T Type of Connection -6 Number of Stations - Design Number : Station : Stations MMC : ase late 3 T:Threaded : Stations 6:6 Stations Connection 3:3 Stations 7:7 Stations 4:4 Stations Design Standard None: Japanese Standard "JIS" 8 : European Design Standard 9 : N.merican Design Standard ressure Drop Hydraulic luid: Viscosity 3 mm /s (64 SSU), Specific Gravity.8 SI Ma.3 4 ressure Drop 3.. T ' T' ' ' ' L/min T ' T T' ' U.S.GM () T Graphic Symbol () T (T) T () MMC-3-T- Graphic Symbol MMC-3-T--7 Detailed Graphic Symbol T (T) (T) Mounting Surface Dimensions for 3/8 Modular Valve When the standard base plate (MMC-3) is not used, the following mounting surface must be prepared. lso, the mounting surface must have a good machined finish. Min. itch: 7(.9) 46(.8).4 (.84) 3. (.8) 6.4 (.) "C" Thd. 3(.) Deep 4 laces Instructions lthough two ports are provided for both pressure port "" and tank port "T", either may be used. However, the ports having () or (T) in the drawing are normally plugged. Remove the plugs of the ports when they are used. Make sure that the ports that are not currently used are properly plugged. 9 (3.6) 9 (.7) 6.7(.66) 7(.6) 37.3(.47) 4(.3) 3. (.3) DIMENSIONS IN MILLIMETRES (INCHES) Design Std. "C" Thd. 7(.76) (.47) (.43) Dia. (Max.) 4 laces Japanese Standard "JIS" and European Design Standard N.merican Design Standard M6 /4- UNC No.44

45 ase lates or 3/8 Modular Valve Installation Drawing MODULR VLVES MMC-3-T--/9 (3.94) 8.8(.3) Dia. Through 4(.) C' bore "" Deep 4 laces 79(3.) 3(.6) (.39) 46 (.8) (.39) (4.33) 9(3.4) T (.7) 46 3 (.8) (.6) 8 4 (.7) (.3) "E" Thd. 3(.) Deep 4 laces (.43) Dia. 4 laces Cylinder ort "" "D" Thd. 79(3.) 3(.6) DIMENSIONS IN MILLIMETRES (INCHES) 6 (.36) T () 47. (.87) 9(3.74) 7.(.8) 47. (.87) (T) 6 (.36) Tank ort "T" "C" Thd. MMC-3-T- -/9 Number of Station (-7 Stations) 79(3.) 4(.7) 3(.6) (3.94) (.39) 46 (.8) (.39) T 3 (.6) (.7) 7 (.9) itch. (.89) Threaded Holes 4 laces ort Holes 4 laces itch 7 (.9) 7 (.9) 7 (.9) Cylinder ort "" "D" Thd. L L Each Station ressure ort "" "C" Thd. 3/8-6 UNC Thd. 8(.7) Deep oth Ends or Eye olts or bove Three Stations Type [MMC-3-T- -9 Models Only] M Thd..6(.86) Deep laces or Eye olts. or bove Three Stations Type [MMC-3-T- - Models Only] 8.(.33) Dia. Through 4(.) C' bore "" Deep 4 laces 3(.6) 79(3.) 4(.7) (.9) 6 (.36) T () (.9) 47. (.87) 9(3.74) 7.(.8) 47. (.87) (T) 6 (.36) Tank ort "T" "C" Thd.. (.89) Cylinder ort "" Each Station "D" Thd. Cylinder ort "" Each Station "D" Thd. or other dimensions, refer to above Model MMC-3-T-. ressure ort "" "C" Thd. MMC-3-T-- MMC-3-T--9 MMC-3-T-- MMC-3-T--9 MMC-3-T-3- MMC-3-T-3-9 MMC-3-T-4- MMC-3-T-4-9 MMC-3-T-- MMC-3-T--9 MMC-3-T-6- MMC-3-T-6-9 MMC-3-T-7- MMC-3-T-7-9 "C" Thd. Rc 3/4 3/4 NT Rc 3/4 3/4 NT Rc 3/4 3/4 NT Rc 3/4 3/4 NT Rc 3/4 3/4 NT Rc 3/4 3/4 NT Rc 3/4 3/4 NT Thread Size "D" Thd. "E" Thd. Rc / M6 / NT /4- UNC Rc / M6 / NT /4- UNC Rc / M6 / NT /4- UNC Rc / M6 / NT /4- UNC Rc / M6 / NT /4- UNC Rc / M6 / NT /4- UNC Rc / M6 / NT /4- UNC Dimensions mm (Inches) L L 8.6 (.34) (.87) 8.6 (.34) 8 6 (.87) (7.8) (6.) 8.6 (.34) 6 4 (.87) (.4) (9.4) 8.6 (.34) 33 3 (.87) (3.9) (.4) 8.6 (.34) 4 39 (.87) (6.4) (.3) 8.6 (.34) (.87) (9.9) (8.3) 8.6 (.34) 6 4 (.87) (.) (.6) pprox. Mass kg (lbs.) 8. (8.7) 4 (3.8) 9. (43.) (.) 3. (67.) 36 (79.3) 4 (9.4) No.4