Series PW

Transcription

1 Series Filter Regulator Specifications H U Model Port size Rc(PT)/NPT 1/8", 1/4" 1/4", 3/8" 3/8", 1/2" 3/4", 1" Max. Supply Pressure 1.5MPa(213 PSI) Max. Operating Pressure 1MPa(150 PSI) Regulating Range 0.05~0.85MPa(7~125 PSI) Port size for 1/8" (Rc(PT)/NPT) Ambient and Media Temperature 5~60C(40~140F) Filtration Standard : 10μm / Option :5μm Bowl Capacity (oz) Bowl Material Construction/Regulator Polycarbonate Relieving type Weight kgf(lbs) 0.3(0.66) 0.56(1.23) 1.15(2.54) 1.41(3.11) 5000 Accessories Symbol Name Pressure gauge Auto Part No TAR TAC TAC TAR / U A-6039 TAF A-6008 TAF A A Min. operating pressure:n O-14.2PSI (Float type) Differential Pressure type How to Order U BG Port Blank : Rc(PT) U : NPT Body Size Rc(PT)/NPT 20 : NPT 1/4 30 : NPT 3/8 40 : NPT 1/2 50 : NPT 1 Port Blank : Rc(PT) G : Rc() 01 : 1/8 02 : 1/4 03 : 3/8 04 : 1/2 06 : 3/4 10 : 1 Accessory B : D : Auto drain:float type(n.o) DF : Auto drain:thread Type U2000 : Differential Pressure type G : Pressure gauge Bowl Guard C : With Bowl Guard (2000, 3000 only) 4000, 5000 : Standard Special Option Blank : None(Standard Type) XC16 : Copper-free C - 41

2 Series Construction/Parts List Symbol Main Parts Material No. Name Note Body Zinc die casting Aluminum Die Cast Baked Enamel Paint(Powder Coating) Bonnet Polyacetal Polyacetal Aluminum Die Cast Black Paint Parts List Part No. No. Parts Name Material Valve Ass y Brass NBR TAW A-6009 TAW A A-6074 Filter Element Bronze TAF TAF TAF Baffle ABS TAF TAF Diaphragm Ass y NBR TAR TAR TAR Deflector ABS TAF TAF Bowl Ass y Polycarbonate TAF TAF Valve Spring Stainless steel TAW TAW TAW Case O-ring NBR V TAF TAF TAF Valve O-ring NBR V TAW TAW TAW O-ring NBR - TAR TAR TAR Note) Bowl assemblies of are fitted with bowl guards(s) Piston Type C - 44

3 Series (53) 2.15 (54.7) 1.18 (30) 1.57 (40) 1.57 (40) 0.24 (6) 0.21 (5.4) Gauge Port Rc(PT)/NPT 1/ (68.8) 6.08 (154.4) 0.09 (2.3) 1.57 (40) 2- Rc(PT)/NPT 1/4" or 1/8" 6.53 (165.8) H U M5/UNF DF:Auto Type DRA 1.97 (50) Auto Type mm(inch) (50) 1.73(68) 3.15(80) 2.70(70) 2.17(55) 0.41(10.5) 11.67(296.5) 0.09(2.3) Port size Rc(PT)/NPT 1(3/4) 0.33(8.5) 1.08(27.5) 2.62(66.5) 4.63(117.5) Gauge Rc(PT)/NPT 1/8 0.83(21) 2.62(66.5) 1.06(27) 11.75(298.5) ф22.5 Rc(PT)/NPT 1/4 Auto Type C - 45

4 Series 3000 L G K E D F M Panel Cut Hole C J фn H 3000:Max.0.14t B Gauge Rc(PT)/NPT 1/8" 1/4, 3/8-Rc(PT)/NPT A 1.57(40) N.O:Rc(PT)/NPT 1/4 Maintenance space With Auto (Float type) Panel Cut Hole L G K E D F M фn :Max.0.2t C J H B Gauge Rc(PT)/NPT 1/8" 1/4, 3/8-Rc(PT)/NPT A 1.57(40) P Maintenance space N.O:Rc(PT)/NPT 1/4" With Auto (Float type) With Auto Model A B C D E F G H J K L M фn P Float type N.O Rc(PT)/NPT /4 3/8 3/8 1/ (53) (211) (92.5) (53) (61.5) (41) (40) (46) (6.5) (8) (53) (2.3) (42.5) (236.5) (70) (266) (112) (70) (68) (50) (54) (54) (8.5) (10.5) (70) (2.3) (52.5) (73) (288) C - 46

5 Series selection Piping Operating Environment Pull the adjustment handle to release the lock and push the handle to engage the lock. If it does not lock easily, tum the handle slightly clockwise or counterclockwise before pushing it. Thming the pressure adjustment handle clockwise increases the secondary pressure and tuming it counterclockwise decreases the pressure. Make sure to check the supply ressure before setting the pressure. The range for setting the secondary pressure is 85% of the supply pressure. Make sure to clean up chips, cutting oil, dust, etc., before piping. When instaling piping or fitting into a port, ensure that sealant material does not enter the port inside. When using seal tape, leave 1.5 to 2 threads exposed on the end of pipe/fitting. Maintenance Inspection Warning Replace the filter element within 2 years of operation or before the pressure drop reaches 0.1MPa. Failure to observe this precaution could damage the filter element. Installation and Adjustment Warning The bowi and the sight dome material is polycarbonate. Therefore, this product cannot be used in an environment or location that is exposed to synthetic oils, organic solvenis, chemicals, or a threadlock agent, etc., which attect the strength of polycarbonate and could cause damage to the product. Do not use in a press machine. It causes damage and maifunction. Auto Pressure Differential auto drain (N.O) When marking drain exhaust piping, Do NOT pipe upwards. Use Compressor with capacity more than 0.75kw [100Nl /min] Set Pressure more than 0.1Mpa H U Set up the regulator while verifying the pressure that is indicated on the supply and the secondary pressure gauges. Turning the handle excessively could damage the internal parts. The pressure gauge that is provided with the product for setting a pressure between 0.02 to 0.2MPa is the 0.2MPa style. To prevent damage to the pressure gauge, make sure that pressure in excess of 0.2MPa is not applied. The adjustment handle must be operated manually. Using a tool to turn the handle could lead to damage. C - 47