74 Series Combination Filter/Regulator and Lubricator Unit, featuring an in-line shut-off valve, and Quikclamp system.

Transcription

1 NCA-33 January 1998 Supersedes November 199 EXCELON Series System Features...2 EXCELON Series Product Features... Filters F72G General Purpose Filters... F73G General Purpose Filters...8 F7G General Purpose Filters...1 F72C Oil Removal (Coalescing) Filters...12 F73C Oil Removal (Coalescing) Filters...1 F7C and F7H Oil Removal (Coalescing) Filters...1 F7V Oil Vapor Removal (Adsorbing) Filters...18 R72G/R/M Pressure Regulators...2 R73G/R Pressure Regulators...22 R7G/R Pressure Regulators...2 B72G General Purpose Filter/Regulators...2 B73G General Purpose Filter/Regulators...28 B7G General Purpose Filter/Regulators...3 L72M Micro-Fog and L72C Oil-Fog Lubricator...32 L73M Micro-Fog and L73C Oil-Fog Lubricator...3 L7M Micro-Fog and L7C Oil-Fog Lubricators...3 V72G Pressure Relief Valves...38 V7G Pressure Relief Valves... T72 Lockout and Shut-Off Valves...2 T73 Lockout and Shut-Off Valves... T7 Lockout and Shut-Off Valves... Combination Units Series 72 Filter-Filter...8 Series 73 Filter-Filter...5 Series 7 Filter-Filter...52 Series 72 Filter-Regulator-Lubricator...5 Series 73 Filter-Regulator-Lubricator...5 Series 7 Filter-Regulator-Lubricator...58 Directional Control Valves P7 Solenoid Operated Directional Control Valves... P7 Air Operated Directional Control Valves 2/2...2 P7 Air Operated Directional Control Valves 3/2... P7 Smooth Start Poppet Valves... P72F Smooth Start/Exhaust Valves...8 P7F Smooth Start/Exhaust Valves...7 EXCELON Accessories and System Components...72 Product Numbering System Charts F72/F73/F7 General Purpose Filters...7 F72/F73/F7 Oil removal (Coalescing) Filters...77 F7V Oil Vapor Removal...78 R72/R73/R7 Pressure Regulators...79 B72/B73/B7 Filter/Regulators...8 L72/L73 Lubricators...81 L7 Lubricators...82 V72/V7 Relief Valves...83 T72/T73/T7 Shut-Off Valves /73/7 Filter-Filter Combinations Units /73/7 F-R-L Combination Units...8 P7 Directional Control Valves...87 P72/P73/P7 Directional Control Valves...88 Warning and Warranty Series Combination Filter/Regulator and Lubricator Unit, featuring an in-line shut-off valve, and Quikclamp system. 1/98 Littleton, CO USA Phone Fax

2 EXCELON Series System Features Features The EXCELON Series, Norgren's premier line of filters, regulators, lubricators, and accessories, is available in 1/", 3/8", 1/2" or 3/" pipe sizes. This newest line of Norgren products features a modular design that allows conventional in-line installation using pipe threads, or modular installation using the patented Quikclamp System. The one-piece Quikclamp assembly allows installation and removal of EXCELON Units and Combination Units without breaking a pipe connection. Aesthetic Appearance External surfaces are protected with a baked on, satin black epoxy paint over a chromate conversion coating, providing excellent corrosion protection and chip resistance. These products have an attractive, contemporary design that will complement the appearance of any OEM equipment. A Wide Range of Options and Accessories The EXCELON Series is available with a wide range of options and accessories, including wall and panel mounting brackets, shut-off valves to isolate and exhaust pressure from downstream equipment, porting blocks to provide auxiliary outlets, electrical pressure switches that monitor system pressure, metal bowl or polycarbonate bowl with metal guard, and many more. These options and accessories allow costefficient customizing for your specific application. piece ball valve that opens and closes with a quick quarter turn. The threaded outlet provides quick, easy connection of a 1/" drain line if desired. The liquid level indicator utilizes a high visibility prismatic lens that allows liquid level monitoring up to 3-feet away at angles up to 2. Nitrile or Fluorocarbon Seals Elastomer seals and diaphragms can be selected for superior compatibility and wear characteristics. Durable, Aluminum Construction The 73 and 7 Series body and metal bowl are manufactured from lightweight, high strength, corrosion resistant aluminum. The 72 Series utilizes zinc, providing high strength and corrosion resistance. Performance Tested The EXCELON Series provides high flow with minimum pressure losses and the accuracy you expect from Norgren Products. In-line installation with a shut-off valve, filter/regulator, pressure switch, and oil removal filter. In-line Installation We designed the EXCELON Series so individual products could be installed directly into the air line with threaded connections if desired. Wall mounting bracket can be used for in-line installation of all EXCELON Series products. Individual units in combinations are connected to each other with the patented Quikclamp. Service Life Indicator Quarter Turn Manual Drain and Liquid Level Indicator The patented quarter turn manual drain and the unique liquid level indicator on metal bowls were designed with the end user in mind. The manual drain is a miniature one- Venting Type Lockout Valve Pressure Switch Prismatic Lens Liquid Level Indicator Rugged 1/ Turn Manual Drain 2 Littleton, CO USA Phone Fax /98

3 EXCELON Series System Features Modular Installation The EXCELON modular system provides a unique and time-saving method of connecting and replacing air line products (filters, regulators, lubricators, valves, etc). The heart of the system is the patented Quikclamp - a simple and unique clamping device that holds the various products in rigid combinations. Flanges on the products slide into V Grooves in the Quikclamp. Two face-sealing o-rings provide a positive seal when the clamp is closed and the captive screw is tightened. Quikclamp Features: True one-piece assembly. No loose parts - nothing to drop on the floor when replacing a unit. The Quikclamp and the EXCELON Series Products can be installed in 9 increments, providing unmatched versatility in orientation. Audible air leak warns of air pressure if the quick release screw is backed off when the unit is pressurized. Wall mounting bracket attaches to the back of the Quikclamp, providing quick, easy installation to a panel, wall, or machine surface. Other Norgren products can be connected to the EXCELON Series using Quikclamps and pipe adapters. The Quikclamp with mounting bracket will actually hold the Excelon components for you, thus freeing your other hand to tighten or adjust the assembly. The 72 Series uses a 3 mm allen wrench, and the 73 and 7 Series use a 5/32" ( mm) allen wrench. Quikclamp Quikclamp Modular System shown includes a filter, regulator, lubricator, smooth-start valve, pipe adapters, and wall mounting brackets. 1/98 Littleton, CO USA Phone Fax

4 EXCELON Series Product Features Filters (General Purpose, Coalescing, and Adsorbing) Regulators Filter/Regulators General purpose filters have a depthtype element with an extra large surface area for extended service life. The elements, available in 5, 25, and µm ratings, can be cleaned in soap and water. High performance oil removal (coalescing) filters have a coalescing element that removes solid particles down to.1 µm. Maximum remaining oil content of air leaving the filter is.1 ppm at 7 F (21 C) with an inlet concentration of 17 ppm. Oil vapor removal (adsorbing) filters have an activated carbon element that acts as an adsorbent in the removal of oil vapors and odors. Maximum remaining oil content of air leaving the filter is.3 ppm at 7 F (21 C) when installed with proper prefilters to remove solids and liquids. Easy to Service Filters can be disassembled for servicing without removal from the air line. The quick release bayonet type bowl can be removed and installed with a quick 1/8 turn. An interlock helps prevent removal when bowl is pressurized. Optional Features General purpose and oil removal filters are available with manual, semiautomatic (72 Series), or automatic drain, metal bowl with liquid level indicator, transparent bowl (72/73 Series), or transparent bowl with metal guard, and a red/green service life indicator that provides a visual indication of the filter element condition. Easy to Service and Adjust Regulator can be disassembled for servicing without removal from the air line. The standard nonrising pressure adjustment knob and the optional T-handle provide easy adjustment at any pressure. Pressure settings are locked by merely pushing on the knob or tightening the T-handle lock nut. Balanced Valve Design The balanced valve provides superior regulation by reducing the effect of variations in inlet pressure on the outlet pressure. Large Area Diaphragm The new, large area diaphragm provides excellent sensitivity for a general purpose regulator. Optional Features Available with or without a pressure gauge, three outlet pressure ranges up to 25 psig (73/7 Series), and relieving or nonrelieving diaphragms. Regulators with a relieving diaphragm reduce the outlet pressure when the pressure setting is reduced, even when the downstream system is dead-ended. Pressure settings on regulators with knob adjustment can be made tamper resistant by the installation of a new tamper resistant shroud. Easy to Service and Adjust Filter/Regulator can be disassembled for cleaning and servicing without removal from the air line. The quick release bayonet type bowl can be removed and installed with a quick 1/8 turn. An interlock helps prevent removal when bowl is pressurized. The depthtype element, which can be cleaned, has an extra large surface area for extended service life. The standard nonrising pressure adjustment knob and the optional T-handle provide easy adjustment at any pressure. Pressure settings are locked by merely pushing down on the knob or tightening the T-handle lock nut. Pressure settings on filter/regulators with knob adjustment can be made tamper resistant by the installation of a new tamper resistant shroud. Balanced Valve Design The balanced valve provides superior regulation by reducing the effect of variations in inlet pressure on the outlet pressure. Optional Features The filter section is available with manual, automatic, or semiautomatic (72 Series) drain, metal bowl with liquid level indicator, transparent bowl (72/73 Series), or transparent bowl with metal guard, 5, 25, or -micron filter element. The regulator section is available with or without a pressure gauge, three outlet pressure ranges up to 25 psig, and a relieving or nonrelieving diaphragm. Filter/regulators with a relieving diaphragm reduce the outlet pressure when the pressure setting is reduced, even when the downstream system is dead-ended. Littleton, CO USA Phone Fax /98

5 EXCELON Series Product Features Lubricators Relief Valve Directional Control, Smooth Start, and Lock Out Valves Easy to Service Lubricator can be disassembled for servicing without removal from the air line. The quick release bayonet type bowl can be removed and installed with a quick 1/8 turn. An interlock prevents removal when bowl is pressurized. Most working parts are contained in a single, removable capsule. The sight lens optically changes when liquid is present, clearly indicating oil level. Micro-Fog and Oil-Fog Micro-Fog and Oil-Fog configurations are available. Micro-Fog lubricators, identified by a red adjustment, are used for applications containing one or more points of lubrication, cylinders, and multiple or single tools. Oil-Fog lubricators, identified by a green adjustment, are commonly used for lubricating a single air tool, cylinder, or air motor, and are located as near the device as possible. Optional Features Available with a transparent reservoir (72/73 Series), metal reservoir with liquid level indicator, transparent reservoir with metal guard, 1-quart metal reservoir (7 Series), and a bidirectional Oil-Fog unit (7 Series). The bidirectional unit is designed for use when the lubricator will be located downstream of frequently cycling directional control valves. Easy to Service and Adjust Relief valve can be disassembled for servicing without removal from the air line. The nonrising pressure adjustment knob provides easy hand adjustment at any pressure range and is locked by merely pushing on the knob. Optional Features Available with or without a pressure gauge and three relief pressure ranges up to 25 psig (7 Series). Shut-Off Valve The 3-way EXCELON Shut-Off Valve, typically attached to the inlet end of a combination unit, is particularly useful for isolating and depressurizing a downstream unit requiring maintenance. These are slide type valves that operate with a quick movement of the slide. The 3-way valve, which is color coded yellow, can be locked only in the closed position. Two-way valves are also available. Subbase Mounted Pressure Switch The modular pressure switch monitors air pressure and provides an electrical output when the pressure drops below or exceeds an adjustable preset pressure. The switch mounts on a subbase that also provides two auxiliary outlets. Configurations Available The modular EXCELON Directional Control Valves are available in 2-port/2- position and in 3-port/2-position configurations with solenoid or air operators (7 Series). Smooth start/ exhaust valves (72/7 Series), and combination smooth start/exhaust valves with lockout option (7 Series) are also available. Connector Options A cable grip connector with or without indicator lights and surge protection is available. Porting Block The modular porting block provides three auxiliary outlets. Manifold Block The modular manifold block provides manifolding capability for up to three components, allowing the system designer to customize each application. 1/98 Littleton, CO USA Phone Fax

6 F72G General Purpose Filter 1/" and 3/8" Port Sizes Excelon design allows in-line or modular installation with other 72, 73, and 7 Series products. High efficiency water and particle removal. Particle removal per ISO , Class 5 and Class 3. See Technical Data. Highly visible, prismatic liquid level indicator lens Optional mechanical service indicator turns from green to red when the filter element needs to be replaced. Optional electrical service indicator provides electrical output when the filter element needs to be replaced. Quick release bayonet bowl Patented quarter turn manual drain Ordering Information Standard Models Model Numbers - Without service indicator: includes automatic drain, Port and 2.2 oz. transparent bowl. Size Weight Flow * PTF lbs. (kg) scfm (dm 3 /s) µm Element 5µm Element. 1/" 1.8 (.9) 5 (2) F72G-2AN-AL3 F72G-2AN-AL1 3/8" 1.8 (.9) 5 (2) F72G-3AN-AL3 F72G-3AN-AL1 * Approximate flow with µm element at 1 psig (.2 bar) inlet pressure and 5 psid (.3 bar) pressure drop. Options - Select the desired filter from the preceding order table, then change the model number as shown in the following diagram to obtain the desired option. Also see Product Numbering Chart on page 7 for additional options. F72G - - Optional Threads Optional Bowl B ISO Rc taper D 1.9 oz metal with liquid G ISO G parallel level indicator* Optional Service Indicator W 2.2 oz. transparent with D With service indicator guard E With electrical service indicator Optional Drain Q 1/ turn manual S Semiautomatic *Automatic drain not available with D bowl option. For other bowl options (shorter and lower 1.9 oz. capacity) consult factory. ISO Symbols Automatic and Semiautomatic drain Operation Manual drain Service Kits Seal and gasket kit: 38-5 Liquid level indicator repair kit: 38-3 Filter element, 5µm: Filter element, µm: Manual drain: 19-5 Semiautomatic drain: Automatic drain: -5R For accessories see pages 72 thru 75. Littleton, CO USA Phone Fax /98

7 Pressure Drop bar,d psid Pressure Drop bar,d psid Technical Data Fluid: Compressed air Maximum Pressure Transparent bowl: 15 psig (1 bar) Metal bowl: 25 psig (17 bar) Operating Temperature* Transparent bowl: to 125 F (-18 to 5 C) Metal bowl: to 15 F (-18 to 5 C) *Air supply must be dry enough to avoid ice formation at temperatures below 35 F (2 C) Particle Removal: 5µm or µm filter element Air Quality: Within ISO , Class 3 and Class 5 Manual drain connection: 7/1-2 UNS male for 1/" tube nut and ferrule Approximate flow at 9 psig (.2 bar) inlet pressure and 5 psid (.3 bar) pressure drop: 5µm element: scfm (22 dm 3 /s) µm element: 5 scfm (2 dm 3 /s) Semiautomatic drain connection: Push on 5/1" (8mm) ID tube Semiautomatic drain operating conditions: Pressure operated Bowl pressure required to close drain: Greater than 1.5 psig (.1 bar) Bowl pressure required to open drain: Less than 1.5 psig (.1 bar) Minimum air flow required to close drain: 1 scfm (.5 dm 3 /s) Manual operation: Lift stem to drain bowl Automatic drain connection: Accepts 1/8 PTF and ISO R1/8 Automatic drain operating conditions: Float operated Bowl pressure required to close drain: Greater than 5 psig (.3 bar) Bowl pressure required to open drain: Less than 3 psig (.2 bar) Minimum air flow required to close drain:.2 scfm (.1 dm 3 /s) Manual operation: Depress pin inside drain outlet to drain bowl NOTE Water vapor will pass through these units and could condense into liquid form downstream as air temperature drops. Install a Norgren air dryer if water condensation could have a detrimental effect on the application. Materials Body: Zinc Bowl Transparent: Polycarbonate Transparent with guard: Polycarbonate, Zinc guard Metal: Zinc Metal Bowl Liquid Level Indicator Lens: Transparent nylon Element: Sintered polypropylene Elastomers: Neoprene & nitrile Optional Service Indicator Body: Transparent nylon Internal parts: Acetal Spring: Stainless steel Elastomers: Nitrile Flow Curve, F72G Port Size: 1/" Inlet psig 25 Pressure bar Flow Curve, F72G Port Size: 1/" Air Flow F72G Performance Characteristics Inlet Pressure psig bar µm Element 8 1 scfm Air Flow µm Element dm 3 /s 8 1 scfm dm 3 /s Dimensions in Inches (mm) * Add 1.7" (3) for semiautomatic drain. ** Add 1.97" (5) for semiautomatic drain, and.28'' (7) for 1/ turn manual drain (5) 1.91 (8) Optional Service Indicator Optional Service Indicator 7.3 (189) Minimum clearance required to remove bowl** 5.3 (138)** 7.27 (185) minimum clearance required to remove bowl* 5.27 (13)*.75 (19) 2.1 (53).75 (19) 2.1 (53) 2.2 ounce bowl with automatic drain 1.9 ounce bowl with 1/ turn manual drain. 1/98 Littleton, CO USA Phone Fax

8 F73G General Purpose Filter 1/", 3/8", 1/2" Port Sizes Excelon design allows in-line or modular installation with other 72, 73, and 7 Series products. High efficiency water and particle removal. Particle removal per ISO , Class 5 and Class 3. See Technical Data. Highly visible, prismatic liquid level indicator lens Optional mechanical service indicator turns from green to red when the filter element needs to be replaced. Optional electrical service indicator provides electrical output when the filter element needs to be replaced. Quick release bayonet bowl Patented quarter turn manual drain Ordering Information ISO Symbols Standard Models Model Numbers - Without service indicator: includes automatic drain, Port and metal bowl with liquid level Size Weight Flow* indicator PTF lbs. (kg) scfm (dm 3 /s) µm Element 5µm Element. 1/" 1.1 (.5) 2 (29) F73G-2AN-AD3 F73G-2AN-AD1 3/8" 1.1 (.5) 75 (35) F73G-3AN-AD3 F73G-3AN-AD1 1/2" 1.1 (.5) 8 (38) F73G-AN-AD3 F73G-3AN-AD1 * Approximate flow with µm element at 1 psig (.2 bar) inlet pressure and 5 psid (.3 bar) pressure drop. Options - Select the desired filter from the preceding order table, then change the model number as shown in the following diagram to obtain the desired option. Also see Product Numbering Chart on page 7 for additional options. Automatic Drain Operation Manual Drain Optional Threads B ISO Rc taper G ISO G parallel F73G - - Optional Bowl T Transparent P Transparent with guard Optional Service Indicator D With mechanical service indicator E With electrical service indicator Optional Drain Q 1/ turn manual Service Kits Seal and gasket kit: 38- Liquid level indicator repair kit: 38-2 Filter element, 5µm: 38-1 Filter element, µm: 38-3 Manual drain: 19-5 Automatic drain: -51R For accessories see pages 72 thru Littleton, CO USA Phone Fax /98

9 F73G Technical Data Fluid: Compressed air Maximum pressure Transparent bowl: 15 psig (1 bar) Metal bowl: 25 psig (17 bar) Operating temperature* Transparent bowl: to 125 F (-2 to 5 C) Metal bowl: to +175 F (-2 to +8 C) *Air supply must be dry enough to avoid ice formation at temperatures below 35 F (2 C.) Typical flow with a µm element at 9 psig (.3 bar) inlet pressure and 7 psig (.5 bar) pressure drop: 75 scfm (35 dm 3 /s) Particle removal: 5µm, 25µm, or µm filter element Air quality: Within ISO , Class 3 and Class 5 (particulates) Manual drain connection: 7/1-2 UNS male for 1/" tube nut and ferrule Automatic drain connection: Accepts 1/8 PTF and ISO R1/8 Automatic drain operating conditions: Float operated Bowl pressure required to close drain: Greater than 5 psig (.3 bar) Bowl pressure required to open drain: Less than 3 psig (.2 bar) Minimum air flow required to close drain:.2 scfm (.1 dm 3 /s) Manual operation: Depress pin inside drain outlet to drain bowl Performance Characteristics Flow Curve, F73G Port Size: 3/8" PRESSURE DROP bar d...2 psid Flow Curve, F73G Port Size: 3/8" Inlet Pressure psig bar 5µm Element scfm dm 3 /s AIR FLOW Materials Body: Aluminum Bowl: Transparent: Polycarbonate Transparent with guard: Polycarbonate, steel guard Metal: Aluminum Metal bowl liquid level indicator lens: Transparent nylon Element: Sintered polypropylene Elastomers: Neoprene and nitrile Mechanical service indicator materials: Body: Transparent nylon Internal parts: Acetal Spring: Stainless steel Elastomers: Nitrile PRESSURE DROP bar d...2 psid Inlet Pressure psig bar µm Element scfm dm 3 /s AIR FLOW Dimensions in Inches (mm) * Minimum clearance required to remove bowl. 2.8 (8) Optional Mechanical Service Indicator 8.15 (27) * 2.3 () 5.8 (17) 8.5 (21) *.15 (15) 1. (25) 1.22 (31) 2.5 (2) Automatic Drain 1/ Turn Manual Drain 1/98 Littleton, CO USA Phone Fax

10 F7G General Purpose Filter 3/8", 1/2", 3/" Port Sizes Excelon design allows in-line or modular installation with other 72, 73, and 7 Series products. High efficiency water and particle removal. Particle removal per ISO , Class 5 and Class 3. See Technical Data. Highly visible, prismatic liquid level indicator lens Optional mechanical service indicator turns from green to red when the filter element needs to be replaced. Optional electrical service indicator provides electrical output when the filter element needs to be replaced. Quick release bayonet bowl Patented quarter turn manual drain Ordering Information Standard Models Model Numbers - Without service indicator: Includes automatic drain and Port metal bowl with liquid level indicator. Size Weight Flow * PTF lbs. (kg) scfm (dm 3 /s) µm Element. 5µm Element. 3/8" 1.82 (.83) 12 (57) F7G-3AN-AD3 F7G-3AN-AD1 1/2" 1.79 (.81) 15 (71) F7G-AN-AD3 F7G-AN-AD1 3/" 1.75 (.79) 15 (71) F7G-AN-AD3 F7G-AN-AD1 * Approximate flow with µm element at 1 psig (.9 bar) inlet pressure and 5 psid (.3 bar) pressure drop. Options - Select the desired filter from the preceding order table, then change the model number as shown in the following diagram to obtain the desired option. Also see Product Numbering Chart on page 7 for additional options. Optional Threads B ISO Rc taper G ISO G parallel Optional Service Indicator D With service indicator E With electrical service indicator Service Kits Seal and gasket kit: 38-7 Liquid level indicator repair kit: 38-5 Filter element, 5µm: 338- Filter element, µm: Manual drain: 19-5 Automatic drain: 3-1 F7G - - Optional Bowl P Transparent with metal guard Optional Drain Q 1/ turn manual ISO Symbols Automatic Drain Operation Manual Drain For accessories see pages 72 thru Littleton, CO USA Phone Fax /98

11 Pressure Drop bar,d psid Pressure Drop bar,d psid F7G Technical Data Fluid: Compressed air Maximum inlet pressure Transparent bowl: 15 psig (1.3 bar) Metal bowl: 25 psig (17.2 bar) Operating temperature* Transparent bowl: to 125 F (-18 to 5 C) Metal bowl: to 175 F (-18 to 79 C) *Air supply must be dry enough to avoid ice formation at temperatures below 35 F (2 C.) Particle removal: 5µm, 25µm, or µm filter element Air quality: Within ISO , Class 3 and Class 5 (particulates) Manual drain connection: 7/1-2 UNS male (for 1/" tube nut and ferrule) Automatic drain connection: Accepts 1/8 PTF Automatic drain operating conditions: Float operated Bowl pressure required to close drain: Greater than 5 psig (.3 bar) Bowl pressure required to open drain: Less than 3 psig (.2 bar) Minimum air flow required to close drain: 2. scfm (1. dm 3 /s) Manual operation: Depress pin inside drain outlet to drain bowl. NOTE Water vapor will pass through these units and could condense into liquid form downstream as air temperature drops. Install a Norgren air dryer if water condensation could have a detrimental effect on the application. Materials Body: Aluminum Bowl Transparent: Polycarbonate with zinc bowl guard Metal: Aluminum Metal bowl liquid level indicator lens: Transparent nylon Element: Sintered polypropylene Elastomers: Nitrile and neoprene Optional service indicator Body: Transparent nylon Internal parts: Acetal Spring: Stainless steel Elastomers: Nitrile Performance Characteristics Flow Curve, F7G Port Size: 1/2" Flow Curve, F7G Port Size: 1/2" Inlet Pressure psig bar 5µm Element scfm dm 3 /s Inlet Pressure psig bar µm Element Air Flow 2.8 Air Flow scfm dm 3 /s Dimensions in Inches (mm) * Minimum clearance required to remove bowl. 1.5 (37) 2.89 (7) 3.15 (8) 3.15 (8) 2.3 () 2.3 () 1. (25) 1. (25) 9.1* (231).35 (11) Automatic Drain 9.7* (2).95 (177) 1/ Turn Manual Drain 1/98 Littleton, CO USA Phone Fax

12 F72C Oil Removal Filter 1/" and 3/8" Port Sizes Excelon design allows in-line or modular installation with other 72, 73, and 7 Series products. High efficiency particle and oil removal, within ISO : Class See Technical Data. Highly visible, prismatic liquid level indicator lens. Patented quarter turn manual drain. Standard mechanical service indicator turns from green to red when the filter element needs to be replaced. Optional electrical service indicator provides electrical output when the filter element needs to be replaced. Quick release bayonet bowl. Patented quarter turn manual drain. Ordering Information Standard Models Flow* Flow* Model Numbers - Port Saturated Dry Service life indicator, Size Weight Element Element automatic drain, 2.2 oz PTF lbs. (kg) scfm (dm 3 /s) scfm (dm 3 /s) transparent bowl 1/".88 (.) 1.5 (.) 1 (8) F72C-2AD-AL 3/8".88 (.) 1.5 (.) 23 (11) F72C-3AD-AL *Approximate flow at 1 psig (.3 bar) inlet pressure and 3. psid (.2 bar) pressure drop. Dry flows good only for systems with all oil, water, and other aerosols removed. Options - Select the desired filter from the preceding order table, then change the model number as shown in the following diagram to obtain the desired option. Also see Product Numbering Chart on page 77 for additional options. Optional Threads B ISO Rc taper G ISO G parallel Standard Service Indicator N Without service indicator E With electrical service indicator F72C - - Optional Bowl D 1.9 oz. metal with liquid level indicator* W 2.2 oz. transparent with guard Optional Drain Q 1/ turn manual S Semiautomatic *Automatic drain not available with D bowl option. For other bowl options (shorter and lower 1.9 oz. capacity) consult factory. Service Kits Seal and gasket kit: 38-5 Liquid level indicator repair kit: 38-3 Filter element, (coalescing): Manual drain: 19-5 Semiautomatic drain: Automatic drain: -5R NOTE For maximum service life, install a general purpose filter with a 5µm element upstream of the oil removal filter. ISO Symbols Automatic and Semiautomatic drain Operation Manual drain For accessories see pages 72 thru Littleton, CO USA Phone Fax /98

13 Pressure Drop bar,d psid Pressure Drop bar,d psid Technical Data Fluid: Compressed air Maximum Pressure Transparent bowl: 15 psig (1 bar) Metal bowl: 25 psig (17 bar) Operating Temperature* Transparent bowl: to 125 F (-18 to 5 C) Metal bowl: to 15 F (-18 to 5 C) *Air supply must be dry enough to avoid ice formation at temperatures below 35 F (2 C). Particle removal down to.1 µm. Air quality: Within ISO , Class 1 (particulates) and Class 2 (oil content) Maximum remaining oil aerosol content of air leaving the filter:.1 ppm at 7 F (21 C) with an inlet concentration of 17 ppm. Approximate flow at 9 psig (.3 bar) inlet pressure: Saturated element: 1.5 scfm (. dm 3 /s) at 3 psid (.2 bar) pressure drop Dry element: 23 scfm (11 dm 3 /s) at 5 psid (.3 bar) pressure drop ** **Dry flows apply only when all oil, water, and other aerosols are removed. Manual Drain Thread: 7/1-2 UNS for 1/" tube nut and ferrule Semiautomatic Drain Connection: Push on 5/1" (8mm) ID tube Semiautomatic drain operating conditions: Pressure operated Bowl pressure required to close drain: Greater than 1.5 psig (.1 bar) Bowl pressure required to open drain: Less than 1.5 psig (.1 bar) Minimum air flow required to close drain: 1 scfm (.5 dm 3 /s) Manual operation: Lift stem to drain bowl Automatic drain connection: Accepts 1/8PTF and ISO R1/8 Automatic drain operating conditions: Float operated Bowl pressure required to close drain: Greater than 5 psig (.3 bar) Bowl pressure required to open drain: Less than 3 psig (.2 bar) Minimum air flow required to close drain:.2 scfm (.1 dm 3 /s) Manual operation: Depress pin inside drain outlet to drain bowl Materials Body: Zinc Bowl Transparent: Polycarbonate Transparent with guard: Polycarbonate, Zinc guard Metal: Zinc Metal Bowl Liquid Level Indicator Lens: Transparent nylon Element: Synthetic fiber and polyurethane foam Elastomers: Neoprene & nitrile Service Indicator Body: Transparent nylon Internal parts: Acetal Spring: Stainless steel Elastomers: Nitrile Flow Curve, F72C (Oil Removal) Port Size: 1/" Filter Element: Coalescing, Saturated Inlet psig 15 Pressure bar Air Flow F72C Performance Characteristics Flow Curve, F72C (Particle Removal) Port Size: 1/" Filter Element: Coalescing, Dry Inlet psig Pressure bar Saturated Element scfm Air Flow Dry Element dm 3 /s scfm dm 3 /s Dimensions in Inches (mm) * Add 1.7'' (3) for semiautomatic drain. ** Add 1.97'' (5) for semiautomatic drain, and.28 (7) for 1/ turn manual drain (5) 1.91 (8) Service Indicator Service Indicator 7.3 (189) Minimum clearance required to remove bowl** 5.3 (138)** 7.27 (185) minimum clearance required to remove bowl* 5.27 (13)*.75 (19) 2.1 (53).75 (19) 2.1 (53) 2.2 ounce bowl with automatic drain 1.9 ounce bowl with 1/ turn manual drain. 1/98 Littleton, CO USA Phone Fax

14 F73C Oil Removal Filter 1/", 3/8", 1/2" Port Sizes Excelon design allows in-line or modular installation with other 72, 73, and 7 Series products. High efficiency particle and oil removal, within ISO : Class See Technical Data. Highly visible, prismatic liquid level indicator lens. Patented quarter turn manual drain. Standard mechanical service indicator turns from green to red when the filter element needs to be replaced. Optional electrical service indicator provides electrical output when the filter element needs to be replaced. Quick release bayonet bowl. Patented quarter turn manual drain. Ordering Information Standard Models Flow* Flow* Model Numbers - Port Saturated Dry mech. service indicator, Size Weight Element Element automatic drain, metal bowl PTF lbs. (kg) scfm (dm 3 /s) scfm (dm 3 /s) w/ liquid level indicator 1/" 1.2 (.5) 21.2 (1.) 28 (13) F73C-2AD-AD 3/8" 1.2 (.5) 21.2 (1.) 3 (1) F73C-3AD-AD 1/2" 1.2 (.5) 21.2 (1.) 37 (17) F73C-AD-AD *Approximate flow at 1 psig (.3 bar) inlet pressure and 3. psid (.2 bar) pressure drop. Dry flows good only for systems with all oil, water, and other aerosols removed. Options - Select the desired filter from the preceding order table, then change the model number as shown in the following diagram to obtain the desired option. Also see Product Numbering Chart on page 77 for additional options. ISO Symbols Automatic Drain Operation Manual Drain Optional Threads B ISO Rc taper G ISO G parallel Standard Service Indicator E With electrical service indicator N Without service indicator F73C - - Optional Bowl T Transparent P Transparent with guard Optional Drain Q 1/ turn manual Service Kits Seal and gasket kit: 38-2 Liquid level indicator repair kit: 38-2 Filter element, (coalescing): -1 Manual drain: 19-5 Automatic drain: -51R NOTE For maximum service life, install a general purpose filter with a 5µm element upstream of the oil removal filter. For accessories see pages 72 thru Littleton, CO USA Phone Fax /98

15 F73C Technical Data Fluid: Compressed air Maximum pressure Transparent bowl: 15 psig (1 bar) Metal bowl: 25 psig (17 bar) Operating temperature* Transparent bowl: to 125 F (-2 to 5 C) Metal bowl: to 15 F (-2 to 5 C) *Air supply must be dry enough to avoid ice formation at temperatures below 35 F (2 C). Maximum flow for 3/8'' ported filters at 9 psig (.3 bar) inlet pressure to maintain consistent oil removal performance: 21.2 scfm (1 dm 3 /s. Particle removal down to.1 µm. Air quality: Within ISO , Class 1 (particulates) and Class 2 (oil content) Maximum remaining oil aerosol content of air leaving the filter:.1 ppm at 7 F (21 C) with an inlet concentration of 17 ppm. Manual drain connection: 7/1-2 UNS male for 1/" tube nut and ferrule Automatic drain connection: Accepts 1/8 PTF and ISO R1/8 Automatic drain operating conditions: Float operated Bowl pressure required to close drain: Greater than 5 psig (.3 bar) Bowl pressure required to open drain: Less than 3 psig (.2 bar) Minimum air flow required to close drain:.2 scfm (.1 dm 3 /s) Manual operation: Depress pin inside drain outlet to drain bowl Recommended prefilter: General purpose filter with a 5µm element Materials Body: Aluminum Bowl: Transparent: Polycarbonate Transparent with guard: Polycarbonate, steel guard Metal: Aluminum Metal bowl liquid level indicator lens: Transparent nylon Element: Synthetic fiber and polyurethane foam Elastomers: Neoprene and nitrile Mechanical service indicator materials: Body: Transparent nylon Internal parts: Acetal Spring: Stainless steel Elastomers: Nitrile Performance Characteristics PRESSURE DROP PRESSURE DROP Flow Curve, F73C (Oil Removal) Port Size: 3/8" Filter Element: Coalescing, Saturated bar d psid Inlet Pressure psig bar Saturated Element scfm dm 3 /s AIR FLOW Flow Curve, F73C (Oil Removal) Port Size: 3/8" Filter Element: Coalescing, Dry bar d psid Inlet Pressure psig bar Dry Element scfm dm 3 /s AIR FLOW Dimensions in Inches (mm) * Minimum clearance required to remove bowl. 2.8 (8) Mechanical Service Indicator 8.15 (27) * 5.8 (17) 8.5 (21) * 1. (25) 2.3 ().15 (15) 1.22 (31) 2.5 (2) Automatic Drain 1/ Turn Manual Drain 1/98 Littleton, CO USA Phone Fax

16 F7C and F7H Oil Removal Filters 3/8", 1/2", 3/" Port Sizes Excelon design allows in-line or modular installation with other 72, 73, and 7 Series products. High efficiency particle and oil removal, within ISO : Class See Technical Data. Highly visible, prismatic liquid level indicator lens. Patented quarter turn manual drain. Standard mechanical service indicator turns from green to red when the filter element needs to be replaced. Optional electrical service indicator provides electrical output when the filter element needs to be replaced. Quick release bayonet bowl. Patented quarter turn manual drain. Ordering Information Standard Models Model Numbers - Flow * Flow * Service life Port Saturated Dry indicator, automatic Size Body and Weight Element Element drain, metal bowl with PTF Element lbs.(kg) scfm (dm 3 /s) scfm (dm 3 /s) liquid level indicator. 3/8" Standard 1.88 (.85) 2 (7) 7 (33) F7C-3AD-AD 1/2" Standard 1.8 (.83) 35 (17) 75 (35) F7C-AD-AD 1/2" High Flow 2.5 (1.11) (28) 1 (7) F7H-AD-AD 3/" High Flow 2. (1.1) (28) 12 (57) F7H-AD-AD * Approximate flow at 1 psig (.9 bar) inlet pressure and 5. psid (.3 bar) pressure drop. Dry flows good only for systems with all oil, water, and other aerosols removed. Options - Select the desired filter from the preceding order table, then change the model number as shown in the following diagram to obtain the desired option. Also see Product Numbering Chart on page 77 for additional options. ISO Symbols Automatic Drain Operation Manual Drain Optional Threads B ISO Rc taper G ISO G parallel Standard Service Indicator N Without service indicator E With electrical service indicator F7C - - Optional Bowl P Transparent with metal guard Optional Drain Q 1/ turn manual Service Kits Seal and gasket kit: Liquid level indicator repair kit: 38-5 Filter element, standard: 3-1 Filter element, high flow: 3-2 Manual drain: 19-5 Automatic drain: 3-1 NOTE For maximum service life, install a general purpose filter with a 5µm element upstream of the oil removal filter. For accessories see pages 72 thru Littleton, CO USA Phone Fax /98

17 Pressure Drop bar,d psid Pressure Drop bar,d psid Pressure Drop bar,d psid Pressure Drop bar,d psid F7C and F7H Technical Data Fluid: Compressed air Maximum inlet pressure Transparent bowl: 15 psig (1.3 bar) Metal bowl: 25 psig (17.2 bar) Operating temperature Transparent bowl: to 125 F (-18 to 52 C) Metal bowl: to 15 F (-18 to 7 C) Air Quality: Within ISO , Class Particle removal down to.1 µm. Maximum remaining oil aerosol content of air leaving the filter:.1 ppm at 7 F (21 C) with an inlet concentration of 17 ppm. Manual drain connection: 7/1-2 UNS male (for 1/" tube nut and ferrule) Automatic drain connection: Accepts 1/8 PTF Automatic drain operating conditions: Float operated Bowl pressure required to close drain: Greater than 5 psig (.3 bar) Bowl pressure required to open drain: Less than 3 psig (.2 bar) Minimum air flow required to close drain: 2. scfm (1. dm 3 /s) Manual operation: Depress pin inside drain outlet to drain bowl. Maximum pressure drop across filter for efficient operation: 1 psid (.9 bar) NOTE Water vapor and oil vapor will pass through these filters and could condense into liquid form downstream as air temperature drops. Install a Norgren air dryer and oil vapor removal filter if water and oil vapor could have a detrimental effect on the application. Performance Characteristics Saturated Elements Flow Curve, F7C (Standard Element for Oil Removal) Port Size: 1/2" Filter Element: Coalescing, Saturated Inlet Pressure psig bar scfm Air Flow Flow Curve, F7H (High Flow Element for Oil Removal) Port Size: 1/2" Filter Element: Coalescing, Saturated. Inlet Pressure psig 25 bar Saturated Element dm 3 /s Materials Body: Aluminum Bowl Transparent: Polycarbonate with zinc bowl guard Metal: Aluminum Metal bowl liquid level indicator lens: Transparent nylon Element: Synthetic fiber and polyurethane foam Elastomers: Nitrile and neoprene Service indicator Body: Transparent nylon Internal Parts: Acetal Spring: Stainless steel Elastomers: Nitrile Dimensions in Inches (mm) * Minimum clearance required to remove bowl (8) Dry Elements 8 1 scfm Air Flow Saturated Element Flow Curve, F7C (Standard Element for Particle Removal) Port Size: 1/2" Filter Element: Coalescing, Dry..3 Inlet Pressure psig bar dm 3 /s (37) 2.89 (7) 1. (25) 2.3 () Dry Element 3.15 (8) 1. (25) 2.3 () 11.19* (28) Automatic Drain 11.79* (299) Manual Drain 8. (215) Automatic Drain 9. (23) 1/ Turn Manual Drain scfm Air Flow Flow Curve, F7H (High Flow Element for Particle Removal) Port Size: 1/2" Filter Element: Coalescing, Dry Inlet psig Pressure bar dm 3 /s 9.1* (231) Automatic Drain.35 (11) Automatic Drain * (2) Manual Drain.95 (177) 1/ Turn Manual Drain.2 2 Dry Element scfm dm 3 /s Air Flow 1/98 Littleton, CO USA Phone Fax

18 F7V Oil Vapor Removal Filters 3/8", 1/2", and 3/" Port Sizes Excelon design allows in-line or modular installation with other 72, 73, and 7 Series products. Activated carbon cartridge filter element adsorbs oil vapors and removes most hydrocarbon odors. Filter and element design optimizes air velocity and contact time to reduce oil content of air leaving the filter to.3 ppm at 7 F (21 C). See NOTE at bottom of page. Long service life of carbon cartridge element. F7C and F7V combinations provide air quality within ISO : Class Quick release bayonet bowl. Ordering Information Standard Models Port Model Numbers Size Weight Flow * Closed bottom metal bowl PTF lbs. (kg) scfm (dm 3 /s) without liquid level indicator. 3/8" 2.5 (1.15) 21 (1) F7V-3AN-EMA 1/2" 2.51 (1.1) 21 (1) F7V-AN-EMA 3/" 2. (1.12) 21 (1) F7V-AN-EMA * Approximate flow at 1 psig (.9 bar) inlet pressure and 5 psid (.3 bar) pressure drop. Options - Select the desired filter from the preceding order table, then change the model number as shown in the following diagram to obtain the desired option. Also see Product Numbering Chart on page 78 for additional options. ISO Symbols Operation Closed Bottom Optional Threads B ISO Rc taper G ISO G parallel F7V- N-EMA Service Kits Seal and gasket kit: Filter element: 31-1 NOTE Oil vapor removal filters must be protected upstream by an oil removal filter. Select a NORGREN oil removal filter with equivalent pipe size and flow capacity equal to or greater than the vapor removal filter. See p. 1 for F7C filter. For accessories see pages 72 thru Littleton, CO USA Phone Fax /98

19 Pressure Drop bar,d psid F7V Technical Data Fluid: Compressed air Maximum inlet pressure: 25 psig (17.2 bar) Operating temperature: to 15 F (-18 to C) Maximum pressure drop across filter for efficient operation: 1 psid (.9 bar) Materials Body: Aluminum Bowl: Aluminum Element: Activated carbon and aluminum Elastomers: Nitrile and neoprene Performance Characteristics Flow Curve, F7V Port Size: 1/2" Filter Element: Adsorbing..3.2 Inlet psig 25 Pressure bar Dimensions in Inches (mm) *Minimum clearance required to remove bowl scfm Air Flow dm 3 /s 1.5 (37) 2.89 (7) 3.15 (8) 1. (25) 11.3* (28) 8.28 (21) 1/98 Littleton, CO USA Phone Fax

20 Excelon design allows in-line or modular installation with other 72, 73, and 7 Series products. R72G/R/M Pressure Regulator Standard, Reverse Flow, and Manifolding Regulators in 1/" and 3/8" Port Sizes Balanced valve design minimizes effect of variation in the inlet pressure on the outlet pressure. Standard relieving models allow reduction of downstream pressure when the system is dead-ended. Non-relieving models optional. Push to lock adjusting knob with tamper resistant accessory. High flow capacity with full flow gauge ports. Reverse flow models available for use in applications where air must be exhausted back through the regulator (i.e., downstream of cycling valves). Manifolding models typically allow up to six regulators to be connected without a booster signal. Ordering Information ISO Symbols Standard Models Model Numbers - Relieving diaphragm, with gauge. Outlet Pressure Adjustment Range*, unidirectional flow Port Knob Adjustment Knob Adjustment Size Weight 5 to psig 5 to 15 psig PTF lbs. (kg) (.3 to bar) (.3 to 1 bar) 1/".79 (.3) R72G-2AK-RFG R72G-2AK-RMG 3/8".79 (.3) R72G-3AK-RFG R72G-3AK-RMG * Do not use these regulators to control pressures outside of the specified ranges. Options - Select the desired regulator from the preceding order table, then change the model number as shown in the following diagram to obtain the desired option. Also see Product Numbering Chart on page 79 for additional options. Relieving Operation Nonrelieving Flow Type G Standard R Reverse M Manifold Optional Threads B ISO Rc taper G ISO G parallel Optional Adjustment T T-handle R72G - - Standard Gauge N Without gauge Optional Diaphragm N Nonrelieving Service Kits Relieving Nonrelieving For accessories see pages 72 thru Littleton, CO USA Phone Fax /98

21 Outlet Pressure bar,g psid Outlet Pressure bar,g psid R72G/R/M Technical Data Fluid: Compressed air Maximum Pressure: 3 psig (2 bar) Operating Temperature*: to 15 F (-18 to 5 C) *Air supply must be dry enough to avoid ice formation at temperatures below 35 F (2 C). Approximate flow of 75 scfm (35.dm3/s) at 15 psig (1 bar) inlet pressure, 9 psig (.3 bar) set pressure and a drop of 15 psig (1 bar) from set. Gauge Ports: 1/8" PTF with PTF main ports 1/8" ISO Rc with ISO Rc main ports 1/8" ISO Rc with iso G main ports Materials Body: Zinc Bonnet: Acetal Valve: Brass Elastomers: Nitrile Bottom Plug: Acetal Dimensions in Inches (mm) Panel mounting hole diameter: 1.57" ( mm) Panel thickness:.1" ( mm) maximum 2.8 (3) Performance Characteristics Flow Curve, R72 Port Size: 1/" Inlet Pressure: 15 psig (1 bar) Range: 5. to 15 psig (.3 to 1 bar) 8 1 scfm Air Flow Flow Curve, R72 Port Size: 1/" Inlet Pressure: 1 psig (7 bar) Range: 5. to 15 psig (.3 to 1 bar) dm 3 /s 1.91 (8) 1.91 (8) (35) 1.38 (35) scfm Air Flow dm 3 /s 1.1 (2) 1.31 (33) 2.88 (73) 1.98 (5) 1.98 (5) 1.1 (2).3 (12) 1.31 (33) OUTLET PRESSURE bar g 8 2 psig Flow Curve, R72M Port Size: 3/8'' Inlet Pressure: 15 psig (1 bar) Range: 5. to 15 psig (.3 to 1 bar) scfm dm 3 /s AIR FLOW Manifold Regulators 2.8 (3) Typical Manifold Regulator Application 1/" OR 3/8" INLET PORT OUTLET PRESSURE 1/8" GAUGE PORT 1/" OR 3/8" INLET PORT 1.89 (8) 2.3 () 1.89 (8) 2.3 () Pressure in Booster signal R72M R72M R72M R72M R72M R72M 1/" OUTLET PORT 1/98 Littleton, CO USA Phone Fax

22 R73G/R Pressure Regulators 1/" 3/8", 1/2"Port Sizes Excelon design allows in-line or modular installation with other 72, 73, and 7 Series products. Balanced valve design minimizes effect of variation in the inlet pressure on the outlet pressure. Standard relieving models allow reduction of downstream pressure when the system is dead-ended. Non-relieving models optional. Push to lock adjusting knob with tamper resistant accessory. High flow capacity with full flow gauge ports. Reverse flow models available for use in applications where air must be exhausted back through the regulator (i.e., downstream of cycling valves). Ordering Information Standard Models Model Numbers - Relieving diaphragm, with gauge. Outlet Pressure Adjustment Range*, unidirectional flow Port Knob Adjustment Knob Adjustment Knob Adjustment Size Weight 5 to psig 5 to 15 psig 1 to 25 psig PTF lbs. (kg) (.3 to bar) (.3 to 1 bar) (.7 to 17 bar) 1/" 1.1 (.8) R73G-2AK-RFG R73G-2AK-RMG R73G-2AK-RSG 3/8" 1.1 (.8) R73G-3AK-RFG R73G-3AK-RMG R73G-3AK-RSG 1/2" 1.1 (.8) R73G-AK-RFG R73G-AK-RMG R73G-AK-RSG * Do not use these regulators to control pressures outside of the specified ranges. Options - Select the desired regulator from the preceding order table, then change the model number as shown in the following diagram to obtain the desired option. Also see Product Numbering Chart on page 79 for additional options. ISO Symbols Relieving Operation Non relieving Flow Type G Standard R Reverse Optional Threads B ISO Rc taper G ISO G parallel Optional Adjustment T T-handle R73G - - Standard Gauge N Without gauge Optional Diaphragm N Nonrelieving Service Kits Relieving 381- Nonrelieving For accessories see pages 72 thru Littleton, CO USA Phone Fax /98

23 R73G/R Technical Data Fluid: Compressed air Maximum pressure: 3 psig (2 bar) Operating temperature*: to 175 F (-2 to 8 C) *Air supply must be dry enough to avoid ice formation at temperatures below 35 F (2 C). Approximate flow at 15 psig (1 bar) inlet pressure, 9 psig (.3 bar) set pressure and a drop of 15 psig (1 bar) from set: 127 scfm ( dm3/s) Gauge ports: 1 PTF with PTF main ports ISO Rc1/ with ISO Rc main ports ISO Rc1/8 with ISO G main ports Materials Body: Aluminum Bonnet : Aluminum Valve: Brass Elastomers: Nitrile Bottom plug: Acetal OUTLET PRESSURE Performance Characteristics bar 2 psig Port Size: 3/8" Inlet Pressure: 15 psig (1 bar) Range: 5 to 15 psig (.3 to 1 bar) scfm dm 3 /s AIR FLOW Dimensions in Inches (mm) Panel mounting hole diameter: 1.89" (8 mm) Panel thickness:." to.25" (2 to mm) 2.8 (8) 1.22 (31) 2.5 (2) OUTLET PRESSURE bar 2.2 (5) 2. (5).5 (12) 9 (3.8). (13) 1.22 (31) 1.5 (39) 2 psig Port Size: 3/8" Inlet Pressure: 1 psig (7 bar) Range: 5 to 15 psig (.3 to 1 bar) scfm dm 3 /s AIR FLOW 1/98 Littleton, CO USA Phone Fax

24 Excelon design allows in-line or modular installation with other 72, 73, and 7 Series products. R7G Pressure Regulators 3/8", 1/2" and 3/" Port Sizes Balanced valve design minimizes effect of variation in the inlet pressure on the outlet pressure. Standard relieving models allow reduction of downstream pressure when the system is dead-ended. Non-relieving models optional. Push to lock adjusting knob with tamper resistant accessory. High flow capacity with full flow gauge ports. Reverse flow models available for use in applications where air must be exhausted back through the regulator (i.e., downstream of cycling valves). Ordering Information ISO Symbols Standard Models Model Numbers - Relieving diaphragm, with gauge. Outlet Pressure Adjustment Range * Port Knob Adjustment Knob Adjustment T-Handle Adjustment Size Weight 5 to psig 5 to 15 psig 1 to 25 psig ** PTF lbs.kg (.3 to bar) (.3 to 1 bar) (.7 to 1 bar) 3/8" 1.8 (.82) R7G-3AK-RFG R7G-3AK-RMG R7G-3AT-RSG 1/2" 1.77 (.8) R7G-AK-RFG R7G-AK-RMG R7G-AT-RSG 3/" 1.73 (.78) R7G-AK-RFG R7G-AK-RMG R7G-AT-RSG * Do not use these regulators to control pressures outside of the specified ranges. ** Regulators with the 25 psig spring are not available with the knob adjustment. Options - Select the desired regulator from the preceding order table, then change the model number as shown in the following diagram to obtain the desired option. Also see Product Numbering Chart on page 79 for additional options. Relieving Operation Nonrelieving Optional Flow R Reverse flow Optional Threads B ISO Rc taper G ISO G parallel Optional Adjustment T T-handle R7 - - Service Kits Seal and gasket kit for relieving regulators : Seal and gasket kit for nonrelieving regulators : Standard Gauge N Without gauge Optional Diaphragm N Nonrelieving For accessories see pages 72 thru Littleton, CO USA Phone Fax /98

25 Outlet Pressure bar,g psig Outlet Pressure bar,g psig R7G Technical Data Fluid: Compressed air Maximum inlet pressure: 3 psig (2.7 bar) Operating temperature*: to 175 F (-18 to 79 C). *Air supply must be dry enough to avoid ice formation at temperatures below 35 F (2 C). Approximate flow at 15 psig (1 bar) inlet pressure, 9 psig (.3 bar) set pressure and a drop of 15 psig (1 bar) from set: 225 scfm (1 dm3/s) Gauge ports: 1/" PTF with PTF main ports. 1/" ISO Rc with ISO Rc main ports. 1/8" ISO Rc with ISO G main ports. Performance Characteristics Flow Curve, R7 Port Size: 1/2'' Inlet Pressure: 15 psig (1 bar) Outlet Pressure: 5. to 15 psig (.3 to 1 bar) Materials Body: Aluminum Bonnet: Aluminum Valve: Brass Elastomers: Nitrile Bottom Plug: Acetal scfm dm 3 /s Air Flow Flow Curve, R7 Port Size: 1/2'' Inlet Pressure: 1 (7 bar) Outlet Pressure: 5. to 15 psig (.3 to 1 bar) Dimensions in Inches (mm) Panel mounting hole diameter: 2." (52mm) Panel thickness:." to.25" (2 to mm) (37) 2.89 (7) 1.5 (37) 2.89 (7) scfm dm 3 /s Air Flow 2.2 (5) 2.2 (5) 3.15 (8) 3.15 (8) 1.9 (3) 1.9 (3).98 (127) 5.95 (151) 1/98 Littleton, CO USA Phone Fax

26 Excelon design allows in-line or modular installation with other 72, 73, and 7 Series products. Combines the functions of a filter and pressure regulator into one compact, space saving unit. High efficiency water and particle removal. Highly visible, prismatic liquid level indicator lens Quick release bayonet bowl Balanced valve design minimizes effect of variation in the inlet pressure on the outlet pressure Standard relieving models allow reduction of downstream pressure when the system is dead-ended. Non-relieving models options. High flow capacity with full flow gauge ports B72G General Purpose Filter/Regulator 1/" and 3/8" Port Sizes Low torque, non-rising pressure adjustment knob or sturdy T-handle provide easy hand adjustment at any pressure. The knob has an integral locking device which can be made tamper resistant with the addition of a tamper resistant kit. Ordering Information Standard Models Model Numbers - Automatic drain, knob adjustment, 2.2 oz. transparent bowl without guard, µm element, relieving diaphragm. Port Outlet Pressure Adjustment Range* Size Weight 5 to psig 5 to 15 psig PTF lbs.(kg) (.3 to bar) (.3 to 1 bar) 1/" 1.15 (.52) B72G-2AK-AL3-RFG B72G-2AK-AL3-RMG 3/8" 1.15 (.52) B72G-3AK-AL3-RFG B72G-3AK-AL3-RMG * Do not use these filter/regulators to control pressures outside of the specified ranges. ISO Symbols Automatic, and Semiautomatic Drain, Relieving Automatic, and Semiautomatic Drain, Nonrelieving Manual Drain, Relieving Manual Drain, Nonrelieving Options - Select the desired filter/regulator from the preceding order table, then change the model number as shown in the following diagram to obtain the desired option. Also see Product Numbering Chart on page 8 for additional options. Optional Threads B ISO Rc taper G ISO G parallel Optional Adjustment T T-handle Optional Drain Q 1/ turn manual S Semiautomatic B72G Standard Gauge N Without gauge Optional Diaphragm N Nonrelieving Optional Element 1 5µm Optional Bowl D Metal with liquid level indicator* W 2.2 oz. transparent with guard *Auto drain not available with D bowl option. For other bowl options (shorter and lower 1.9 oz. capacity) consult factory. Service Kits Seal and gasket kit for relieving filter/regulators: Seal and gasket kit for nonrelieving filter/regulators: Liquid level indicator repair kit: 38-3 Filter element, 5µm: Filter element, µm: Manual drain: 19-5 Semiautomatic drain: Automatic drain: -5R Operation For accessories see pages 72 thru Littleton, CO USA Phone Fax /98

27 Outlet Pressure bar,g psid Outlet Pressure bar,g psid B72G Technical Data Fluid: Compressed air Maximum Inlet Pressure Transparent bowl: 15 psig (1 bar) Metal bowl: 25 psig (17 bar) Operating Temperature* Transparent bowl: to 125 F (-18 to 5 C) Metal bowl: to 15 F (-18 to 5 C) *Air supply must be dry enough to avoid ice formation at temperatures below 35 F (2 C). Air Quality: Within ISO , Class 3 and Class 5 Approximate flow at 15 psig (1 bar) inlet pressure, 9 psig (.3 bar) set pressure and a drop of 15 psig (1 bar) from set: 8 scfm (38 dm3/s) Manual drain connection: 7/1-2 UNS male for 1/" tube nut and ferrule Semiautomatic drain connection: Push on 5/1" (8mm) ID tube Semiautomatic drain operating conditions: Pressure operated Bowl pressure required to close drain: Greater than 1.5 psig (.1 bar) Bowl pressure required to open drain: Less than 1.5 psig (.1 bar) Minimum air flow required to close drain: 1 scfm (.5 dm 3 /s) Manual operation: Lift stem to drain bowl Automatic drain connection: Accepts 1/8PTF and ISO R1/8 Automatic drain operating conditions: Float operated Bowl pressure required to close drain: Greater than 5 psig (.3 bar) Bowl pressure required to open drain: Less than 3 psig (.2 bar) Minimum air flow required to close drain:.2 scfm (.1 dm 3 /s) Manual operation: Depress pin inside drain outlet to drain bowl Gauge Ports: 1/8" PTF with PTF main ports 1/8" ISO Rc with ISO Rc main ports 1/8" ISO Rc with iso G main ports NOTE Water vapor will pass through these units and could condense into liquid form downstream as air temperature drops. Install a Norgren air dryer if water condensation could have a detrimental effect on the application. Performance Characteristics Air Flow Flow Curve, B72 Port Size: 1/" Inlet Pressure: 15 psig (1 bar) Range: 5 to 15 psig (.3 to 1 bar) Element: µm 8 1 scfm dm 3 /s Flow Curve, B72 Port Size: 1/'' Inlet Pressure: 1 psig (7 psig) Range: 5. to 15 psig (.3 to 1 bar) Element: µm scfm Materials Body: Zinc Bonnet: Acetal Valve: Brass Bowl: Transparent Polycarbonate Transparent with guard Polycarbonate, Zinc guard Metal Zinc Metal bowl liquid level indicator lens: Transparent nylon Element: Sintered polypropylene Elastomers: Neoprene & nitrile Dimensions in Inches (mm) Panel mounting hole diameter: 1.57" ( mm) Panel thickness: " to.1" ( to mm 7.3 (189) Minimum clearance required to remove bowl** 1.1 (2) 2.89 (73) 5.3 (138) ** 7.27 (185) minimum clearance required to remove bowl* 1.98 (5) 1.1 (2) 1.91 (8) 1.38 (35) 5.27 (13) * 2.89 (73) Air Flow 7.27 (185) minimum clearance required to remove bowl* 2.8 (3) 1.1 (2) dm 3 /s 5.27 (13) * 3.73 (95) 1.38 (35) 1.91 (8) 2.2 ounce bowl with automatic drain 1.9 ounce bowl with 1/ turn manual drain. 1.9 ounce bowl with 1/ turn manual drain. 1/98 Littleton, CO USA Phone Fax

28 Excelon design allows in-line or modular installation with other 72, 73, and 7 Series products. Combines the functions of a filter and pressure regulator into one compact, space saving unit. High efficiency water and particle removal. Highly visible, prismatic liquid level indicator lens Quick release bayonet bowl Balanced valve design minimizes effect of variation in the inlet pressure on the outlet pressure Standard relieving models allow reduction of downstream pressure when the system is dead-ended. Non-relieving models options. High flow capacity with full flow gauge ports Low torque, non-rising pressure adjustment knob or sturdy T-handle provide easy hand adjustment at any pressure. The knob has an integral locking device which can be made tamper resistant with the addition of a tamper resistant kit. B73G General Purpose Filter/Regulator 1/", 3/8", 1/2" Port Sizes Ordering Information Standard Models Model Numbers - Automatic drain, knob adjustment, metal bowl with liquid level indicator, µm element, relieving diaphragm, gauge. Port Outlet Pressure Adjustment Range* Size Weight 5 to psig 5 to 15 psig 1 to 25 psig PTF lbs.(kg) (.3 to bar) (.3 to 1 bar) (.9 to 17 bar) 1/" 1.5 (.7) B73G-2AK-AD3-RFG B73G-2AK-AD3-RMG B73G-2AK-AD3-RSG 3/8" 1.5 (.7) B73G-3AK-AD3-RFG B73G-3AK-AD3-RMG B73G-3AK-AD3-RSG 1/2" 1.5 (.7) B73G-AK-AD3-RFG B73G-AK-AD3-RMG B73G-AK-AD3-RSG * Do not use these filter/regulators to control pressures outside of the specified ranges. Options - Select the desired filter/regulator from the preceding order table, then change the model number as shown in the following diagram to obtain the desired option. Also see Product Numbering Chart on page 8 for additional options. ISO Symbols Automatic Drain, Relieving Automatic Drain, Non-Relieving Manual Drain, Relieving Manual Drain, Non-Relieving Optional Threads B ISO Rc taper G ISO G parallel Optional Adjustment T T-handle Optional Drain Q 1/ turn manual B73G Standard Gauge N Without gauge Optional Diaphragm N Nonrelieving Optional Element 1 5µm 2 25µm 3 µm Optional Bowl P Transparent with guard* T Transparent* *Filter/Regulators with 25 psig spring are not available with T or P bowls. Service Kits Seal and gasket kit for relieving filter/regulators: 383- Seal and gasket kit for nonrelieving filter/regulators: 38-1 Liquid level indicator repair kit: 38-2 Filter element, 5µm: 38-1 Filter element, 25µm: 38-2 Filter element, µm: 38-3 Manual drain: 19-5 Automatic drain: -51R For accessories see pages 72 thru Littleton, CO USA Phone Fax /98

29 B73G Technical Data Fluid: Compressed air Maximum pressure Transparent bowl: 15 psig (1 bar ) Metal bowl: 25 psig (17 bar) Operating temperature* Transparent bowl: to 125 F (-2 to 5 C) Metal bowl: to 175 F (-2 to 8 C) *Air supply must be dry enough to avoid ice formation at temperatures below 35 F (2 C). Approximate flow at 15 psig (1 bar) inlet pressure, 9 psig (.3 bar) set pressure and a drop of 15 psig (1 bar) from set: 1 scfm (5 dm3/s) Particle removal: 5, 25 or µm filter element Air quality: Within ISO , Class 3 and Class 5 (particulates) Manual drain connection: 7/1-2 UNS male for 1/" tube nut and ferrule Automatic drain connection: Accepts ISO R1/8 and 1/8PTF Automatic drain operating conditions: Float operated Bowl pressure required to close drain: Greater than 5 psig (.3 bar) Bowl pressure required to open drain: Less than 3 psig (.2 bar) Minimum air flow required to close drain:.2 scfm (.1 dm 3 /s) Manual operation: Depress pin inside drain outlet to drain bowl Gauge ports: 1 PTF with PTF main ports ISO Rc1/ with ISO Rc main ports ISO Rc1/8 with ISO G main ports Performance Characteristics OUTLET PRESSURE bar 2 bar psig psig 1 FLOW CHARACTERISTICS Port Size: 3/8" Element: µm Inlet Pressure: 15 psig (1 bar) Range: 5 to 15 psig (.3 to 1 bar) scfm dm 3 /s AIR FLOW FLOW CHARACTERISTICS Port Size: 3/8" Element: µm Inlet Pressure: 1 psig (7 bar) Range: 5 to 15 psig (.3 to 1 bar) Materials Body: Aluminum Bonnet: Aluminum Valve: Brass Bowl Transparent: Polycarbonate Transparent with guard: Polycarbonate, steel guard Metal: Aluminum Metal bowl liquid level indicator lens: Transparent nylon Element: Sintered plastic Elastomers: Neoprene and nitrile OUTLET PRESSURE scfm dm 3 /s AIR FLOW Dimensions in Inches (mm) Panel mounting hole diameter: 8 mm (1.89") Panel thickness: 2 to mm (." to.25") * Minimum clearance to remove bowl (31) 2.8 (8) 2.5 (2) 1.22 (31).5 (12) 3.8 (9). (13) 2. (5) 2.2 (5) 8.15 (27) * 5.8 (17) 8.5 (21) *.15 (15) Automatic Drain 1/ Turn Manual Drain 1/98 Littleton, CO USA Phone Fax

30 B7G Filter/Regulator 3/8", 1/2", and 3/" Port Sizes Excelon design allows in-line or modular installation with other 72, 73, and 7 Series products. Combines the functions of a filter and pressure regulator into one compact, space saving unit. High efficiency water and particle removal. Highly visible, prismatic liquid level indicator lens Quick release bayonet bowl Balanced valve design minimizes effect of variation in the inlet pressure on the outlet pressure Standard relieving models allow reduction of downstream pressure when the system is dead-ended. Non-relieving models options. High flow capacity with full flow gauge ports Low torque, non-rising pressure adjustment knob or sturdy T-handle provide easy hand adjustment at any pressure. The knob has an integral locking device which can be made tamper resistant with the addition of a tamper resistant kit. Ordering Information Standard Models Model Numbers - Automatic drain, metal bowl with liquid level indicator, µm element, relieving diaphragm, with pressure gauge. Outlet Pressure Adjustment Range * Port Knob Adjustment Knob Adjustment T-Handle Adjustment ** Size Weight 5 to psig 5 to 15 psig 1 to 25 psig PTF lbs.(kg) (.3 to bar) (.3 to 1 bar) (.7 to 1 bar) 3/8" 2.2 (1.19) B7G-3AK-AD3-RFG B7G-3AK-AD3-RMG B7G-3AT-AD3-RSG 1/2" 2.59 (1.17) B7G-AK-AD3-RFG B7G-AK-AD3-RMG B7G-AT-AD3-RSG 3/" 2.55 (1.1) B7G-AK-AD3-RFG B7G-AK-AD3-RMG B7G-AT-AD3-RSG * Do not use these filter/regulators to control pressures outside of the specified ranges. ** Filter/regulators with 25 psig spring are not available with the knob adjustment or P bowl. ISO Symbols Automatic Drain, Relieving Automatic Drain, Nonrelieving Operation Manual Drain, Relieving Manual Drain, Nonrelieving Options - Select the desired filter/regulator from the preceding order table, then change the model number as shown in the following diagram to obtain the desired option. Also see Product Numbering Chart on page 8 for additional options. B7G Optional Threads Standard Gauge B ISO Rc taper N Without gauge G ISO G parallel Optional Diaphragm Optional Adjustment N Nonrelieving T T-handle Optional Element Optional Drain Q 1/ turn manual Service Kits Seal and gasket kit for relieving filter/regulators: Seal and gasket kit for nonrelieving filter/regulators: Liquid level indicator repair kit: 38-5 Filter element, 5µm: 338- Filter element, µm: Manual drain: 19-5 Automatic drain: µm Optional Bowl P Plastic with metal guard For accessories see pages 72 thru Littleton, CO USA Phone Fax /98

31 Outlet Pressure bar,g psig Outlet Pressure bar,g psig B7G Technical Data Fluid: Compressed air Maximum inlet pressure Transparent bowl: 15 psig (1.3 bar) Metal bowl: 25 psig (17.2 bar) Temperature range* Transparent bowl: to 125 F (-18 to 52 C) Metal bowl: to 175 F (-18 to 79 C) Air Quality: Within ISO , Class 3 and Class 5 *Air supply must be dry enough to avoid ice formation at temperatures below 35 F (2 C). Approximate flow at 15 psig (1 bar) inlet pressure, 9 psig (.3 bar) set pressure and a drop of 15 psig (1 bar) from set: 2 scfm (9 dm3/s). Automatic drain connection: 1/8 NPTF Manual drain connection: 7/1-2 UNS male (for 1/" tube nut and ferrule) Gauge ports: 1/" PTF with PTF main ports. 1/" ISO Rc with ISO Rc main ports. 1/8" ISO Rc with ISO G main ports. Automatic drain minimum operating pressure: 1 psig (.9 bar). The drain is open when the filter is not pressurized and closes when the bowl is pressurized to approximately 5 psig (.35 bar). The automatic drain operates when liquid accumulates above a certain level or when bowl pressure is reduced to zero. NOTE Water vapor will pass through these units and could condense into liquid form downstream as air temperature drops. Install a NORGREN air dryer if water condensation could have a detrimental effect on the application. Performance Characteristics Flow Curve, B7 Port Size: 1/2'' Inlet Pressure: 15 paig (1 bar) Outlet Pressure Adjustment Range: 5. to 15 psig (.3 to 1 bar) scfm dm 3 /s Air Flow Flow Curve, B7 Port Size: 1/2'' Inlet Pressure: 1 psig (7 bar) Outlet Pressure Adjustment Range: 5. to 15 psig Materials Body: Aluminum Bonnet : Aluminum Valve: Brass Bowl: Transparent Polycarbonate with zinc bowl guard Metal Aluminum Metal bowl liquid level indicator lens: Transparent nylon Element: Sintered polypropylene Elastomers: Neoprene & nitrile Dimensions in Inches (mm) Panel mounting hole diameter: 2." (52mm) Panel thickness:." to.25" (2 to mm) * Minimum clearance to remove bowl scfm dm 3 /s Air Flow 1.5 (37) 2.89 (7) 1.5 (37) 2.89 (7) 2.21 (5) 2.21 (5) 3.15 (8) 3.15 (8).98 (127) 5.95 (151) 1.2 (31) 1.2 (31) 9.1* (231) Automatic Drain 1.9 (3).35 (11) Automatic Drain 9.1* (231) Automatic Drain 1.9 (3).35 (11) Automatic Drain 9.7* (2) Manual Drain.95 (177) 1/ Turn Manual Drain 9.7* (2) Manual Drain.95 (177) 1/ Turn Manual Drain 1/98 Littleton, CO USA Phone Fax

32 L72M and L72C Lubricators Micro-Fog and Oil-Fog Lubricators 1/" and 3/8" Port Sizes Excelon design allows in-line or modular installation with other 72, 73, and 7 Series products. Flow sensor design provides a nearly constant oil/air ratio over a wide range of air flows. 3 visibility of the sight-feed dome simplifies installation and adjustment. Highly visible, prismatic liquid level indicator lens. Quick release bayonet bowl with patented quarter turn manual drain. Micro-Fog and Oil-Fog are both available. Use Micro-Fog models to lubricate one or more air driven tools or devices Use Oil-Fog models to lubricate a single air driven tool or device Ordering Information ISO Symbol Standard Models Port Model Numbers - 1/ turn manual drain, Size Weight 2.2 oz. transparent bowl without guard. PTF lbs. (kg) Micro-Fog Oil-Fog 1/" 1.8 (.9) L72M-2AP-QLN L72C-2AP-QLN 3/8" 1.8 (.9) L72M-3AP-QLN L72C-3AP-QLN With drain Options - Select the desired lubricator from the preceding order table, then change the model number as shown in the following diagram to obtain the desired option. Also see Product Numbering Chart on page 81 for additional options. Operation Port Size 2 1/" 3 3/8" Optional Threads B ISO Rc taper G ISO G parallel L72C - P - Q Additional Options P With pyrex dome Optional Bowl* D 1.9 oz. metal with liquid level indicator W 2.2 oz.transparent with guard * For other bowl options consult factory (shorter and lower 1.9 oz. capacity.) Service Kits Seal and gasket kit: Liquid level indicator repair kit: 38-3 Manual drain: 19-5 Micro-Fog Oil-Fog NOTE Models listed in the order table must not be located downstream of frequently cycling directional control valves. Order the optional bidirectional Oil-Fog Lubricator for use under such conditions. For accessories see pages 72 thru Littleton, CO USA Phone Fax /98

33 Pressure Drop bar,d psid L72M/L72C Technical Data Fluid: Compressed air Maximum Pressure Transparent bowl: 15 psig (1 bar) Metal bowl: 25 psig (17 bar) Operating Temperature* Transparent bowl: to 125 F (-18 to 5 C) Metal bowl: to 15 F (-18 to 5 C) *Air supply must be dry enough to avoid ice formation at temperatures below 35 F (2 C). Start point (i.e., minimum airflow required for lubricator operation) Oil-Fog models: 1. scfm (.7 dm3/s) at 9 psig (.3 bar) inlet pressure Micro-Fog models: 2. scfm (.9 dm3/s) at 9 psig (.3 bar) inlet pressure Approximate flow at 9 psig (.3 bar) inlet pressure and 5 psid (.3 bar) pressure drop: 3 scfm (17 dm 3 /s) Nominal Bowl Capacity Long transparent bowl: 2.2 oz (5 ml) Short metal bowl: 1.9 oz (5 ml) Manual Drain Connection: 7/1-2 UNS male for 1/" tube nut and ferrule Recommended lubricants: Use a misting type oil rated 5 to 2 SSU (ISO Grade 7 to ) at 1 F (38 C). The oils used must be compatible with materials of construction. Contact your lubricant supplier and the builder of the equipment to be lubricated to obtain specific lubricant recommendations. Performance Characteristics Flow Curve, L72, Oil-Fog and Micro-Fog Port Size: 1/" Inlet Pressure psig bar Air Flow scfm dm 3 /s Materials Body: Zinc Bowl: Transparent: Polycarbonate Transparent with guard: Polycarbonate, Zinc guard Metal: Zinc Metal bowl liquid level indicator lens: Transparent nylon Sight feed dome: Transparent nylon Elastomers: Neoprene, nitrile, and Geolast Dimensions in Inches (mm) * Minimum clearance required to remove reservoir from unit. Add.5" (1mm) for long (2.2 fluid ounce) reservoir. ** Add.5" (1mm) for long (2.2 fluid ounce) reservoir. Optional pyrex sight feed dome (5) 1.98 (5) Micro-Fog Models 1.91 (8) Oil-Fog Models 8. (215)* 5.27 (13)** 1.91 (8) 8. (215)* 5.27 (13)**.75 (19).75 (19) 1.3 (1) 2.51 () 1.3 (1) 2.51 () Short (1.9 fluid ounce) reservoir Short (1.9 fluid ounce) reservoir 1/98 Littleton, CO USA Phone Fax

34 Excelon design allows in-line or modular installation with other 72, 73, and 7 Series products. L73M and L73C Lubricators Micro-Fog and Oil-Fog Tool Lubricators 1/", 3/8", 1/2" Port Sizes Flow sensor design provides a nearly constant oil/air ratio over a wide range of air flows. 3 visibility of the sight-feed dome simplifies installation and adjustment. Highly visible, prismatic liquid level indicator lens. Quick release bayonet bowl with patented quarter turn manual drain. Micro-Fog and Oil-Fog are both available. Use Micro-Fog models to lubricate one or more air driven tools or devices Use Oil-Fog models to lubricate a single air driven tool or device Ordering Information Standard Models Port Model Numbers - 1/ turn manual drain, Size Weight metal with liquid level indicator PTF lbs. (kg) Micro-Fog Oil-Fog 1/" 1.1 (.5) L73M-2AP-QDN L73C-2AP-QDN 3/8" 1.1 (.5) L73M-3AP-QDN L73C-3AP-QDN 1/2'' 1.1 (.5) L73M-AP-QDN L73C-AP-QDN Options - Select the desired lubricator from the preceding order table, then change the model number as shown in the following diagram to obtain the desired option. Also see Product Numbering Chart on page 81 for additional options. ISO Symbols Operation With Drain Port Size 2 1/" 3 3/8" 1/2'' Optional Threads B ISO Rc taper G ISO G parallel L73C - P - Q Additional Options P With pyrex sight-feed dome Q Quick fill nipple Optional Bowl P Transparent with guard R Metal with Pyrex liquid level indicator T Transparent Service Kits Seal and gasket kit: Liquid level indicator repair kit: 38-3 Manual drain: 19-5 NOTE Models listed in the order table must not be located downstream of frequently cycling directional control valves. Order the optional bidirectional (7 Series) Oil-Fog Lubricator for use under such conditions. For accessories see pages 72 thru Littleton, CO USA Phone Fax /98

35 L73M/L73C Technical Data Fluid: Compressed air Maximum pressure: Transparent bowl: 15 psig (1 bar) Metal bowl: 25 psig (17 bar) Operating temperature* Transparent bowl: to 125 F (-2 to 5 C) Metal bowl: to 175 F (-2 to 8 C) *Air supply must be dry enough to avoid ice formation at temperatures below 35 F (2 C). Start point (minimum flow required for lubricator operation): 1.5 scfm (.71 dm 3 /s) at 9 psig (.3 bar) inlet pressure Maximum recommended flow: scfm (28 dm 3 /s). Air flows above scfm (28 dm3/s) create excessive air velocity, turbulence, and pressure losses. In addition, the fog produced by the lubricator will wet out on the pipe walls and will not be carried by the compressed air to the point of application. Typical flow with 9 psig (.3 bar) inlet pressure and 7 psig (.5 bar) pressure drop: Micro-Fog models: 138 scfm (5 dm 3 /s) Oil-Fog models: 158 scfm (75 dm 3 /s) Nominal bowl size: 3.5 ounce (.1 litre) Manual drain connection: 7/1-2 UNS male (for 1/" tube nut and ferrule) Recommended lubricants: Use a misting type oil rated 5 to 2 SSU (ISO Grade 7 to ) at 1 F (38 C). The oils used must be compatible with materials of construction. Contact your lubricant supplier and the builder of the equipment to be lubricated to obtain specific lubricant recommendations. Materials Body: Aluminum Bowl: Transparent: Polycarbonate Transparent with guard: Polycarbonate, steel guard Metal: Aluminum Metal bowl liquid level indicator lens: Transparent nylon Sight-Feed dome: Transparent nylon Elastomers: Neoprene and nitrile Dimensions in Inches (mm) * Minimum clearance to remove bowl. ** Optional pyrex sight-feed dome. Typical Performance Characteristics PRESSURE DROP PRESSURE DROP Flow Curve, L73, Micro-Fog Port Size: 3/8'' bar d bar d psid psid Inlet Pressure psig bar scfm dm 3 /s Flow Curve, L73, Oil-Fog Port Size: 3/8'' Inlet Pressure psig bar AIR FLOW scfm dm 3 /s AIR FLOW 2.8 (8) 9.29 (23) Closed Bottom * 1. (255) With Drain * 1. (25) 5.38 (137) Closed Bottom.15 (15) With Drain 1.87 (7) 2.7 (7) ** 1.22 (31) 2.5 (2) 1/98 Littleton, CO USA Phone Fax

36 Excelon design allows in-line or modular installation with other 72, 73, and 7 Series products. L7M and L7C Lubricators 3/8", 1/2", and 3/" Port Sizes Micro-Fog and Oil-Fog Tool Lubricators Flow sensor design provides a nearly constant oil/air ratio over a wide range of air flows. 3 visibility of the sight-feed dome simplifies installation and adjustment. Highly visible, prismatic liquid level indicator lens. Quick release bayonet bowl with patented quarter turn manual drain. Micro-Fog and Oil-Fog are both available. Use Micro-Fog models to lubricate one or more air driven tools or devices Use Oil-Fog models to lubricate a single air driven tool or device Ordering Information ISO Symbol Standard Models Model Numbers - 1/ turn manual drain, 7-oz. metal reservoir with Port liquid level indicator. Size Weight * Flow ** PTF lbs. (kg) scfm (dm 3 /s) Micro-Fog Oil-Fog 3/8" 1.7 (.77) 2.5 to (1.2 to 19.) L7M-3AP-QDN L7C-3AP-QDN 1/2" 1.1 (.73) 3.5 to 1 (1.7 to 7.) L7M-AP-QDN L7C-AP-QDN 3/" 1.5 (.71) 3.5 to 1 (1.7 to 7.) L7M-AP-QDN L7C-AP-QDN * Lubricators with 1-quart metal bowl: Add 2.1 lbs (.91 kg). ** Approximate flow at 1 psig (.9 bar) inlet pressure and 5 psid. Options - Select the desired lubricator from the preceding order table, then change the model number as shown in the following diagram to obtain the desired option. Also see Product Numbering Chart on page 82 for additional options. Optional Threads B ISO Rc taper G ISO G parallel Optional Flow Type (Oil-Fog Only) E Bidirectional L7 - - Additional Options Q With quick fill cap P With pyrex dome Optional Reservoirs P 7-oz. transparent with metal guard A 1-qt. metal with pyrex liquid level indicator Operation With drain Service Kits Seal and gasket kit: Liquid level indicator repair kit: 38-5 Manual drain: 19-5 NOTE Models listed in the order table must not be located downstream of frequently cycling directional control valves. Order the optional bidirectional Oil-Fog Lubricator for use under such conditions. Micro-Fog For accessories see pages 72 thru 75. Oil-Fog 3 Littleton, CO USA Phone Fax /98

37 Pressure Drop bar,d psid Pressure Drop bar,d psid L7M/L7C Technical data Maximum inlet pressure Transparent reservoir: 15 psig (1.3 bar) Metal reservoir: 25 psig (17.2 bar) Operating temperature Transparent reservoir: to 125 F (-18 to 52 C) Metal reservoir : to 175 F (-18 to 79 C) Manual drain connection: 7/1-2 UNS male (for 1/" tube nut and ferrule) Recommended lubricants: Use a misting type oil rated 5 to 2 SSU (ISO Grade 7 to ) at 1 F (38 C). The oils used must be compatible with materials of construction. Contact your lubricant supplier and the builder of the equipment to be lubricated to obtain specific lubricant recommendations. Start point (minimum flow required for lubricator operation): 1.5 scfm (.71 dm 3 /s) at 9 psig (.3 bar) inlet pressure Maximum recommended flow: scfm (28 dm 3 /s). Air flows above scfm (28 dm3/s) create excessive air velocity, turbulence, and pressure losses. In addition, the fog produced by the lubricator will wet out on the pipe walls and will not be carried by the compressed air to the point of application. Typical flow with 9 psig (.3 bar) inlet pressure and 7 psig (.5 bar) pressure drop Micro-Fog models: 138 scfm (5 dm 3 /s) Oil-Fog models: 158 scfm (75 dm 3 /s) Performance Characteristics Flow Curve, L7M, Micro-Fog Port Size: 1/2" Inlet Pressure psig bar Air Flow scfm dm 3 /s Materials Body: Aluminum Reservoir Transparent: Polycarbonate with zinc bowl guard Metal: Aluminum Reservoir liquid level indicator lens 7-ounce reservoir: Transparent nylon 1-quart reservoir: Pyrex Sight-Feed dome: Transparent nylon Elastomers: Neoprene and nitrile Dimensions in Inches (mm) *Minimum clearance required to remove bowl..32 (11) Dia (8) Flow Curve, L7C, Oil-Fog Port Size: 1/2" Inlet Pressure psig bar Air Flow scfm dm 3 /s 1.12 (28) 1. (25) 1.5 (37) 2.89 (7) 3.15 (8) 1.12 (28) 1. (25) 2.* (58) 11.9 (33) 1.95* (278).95 (177) 2. (1) 7-Ounce Reservoir 1-Quart Reservoir 1/98 Littleton, CO USA Phone Fax

38 V72G Pressure Relief Valve 1/" and 3/8" Port Sizes Excelon design allows in-line or modular installation with other 72, 73, and 7 Series products. Helps protect air operated equipment from over pressure by retarding excessive pressure build up. Low torque, non-rising pressure adjustment knob or sturdy T-handle provides easy hand adjustment at any pressure. The knob has an integral locking device which can be made tamper resistant with the addition of a temper resistant kit. New design allows for easy inline installation with no tee's required (bottom venting). Ordering Information ISO Symbols Standard Models Model Numbers - Without gauge. Relief Pressure Adjustment Range * Inlet Port Knob Adjustment Knob Adjustment Size Relief Weight 5 to psig 5 to 15 psig PTF Port lbs. kg (.3 to bar) (.3 to 1 bar) 1/" 1/".73 (.33) V72G-2AK-NFN V72G-2AK-NMN 3/8" 1/".73 (.33) V72G-3AK-NFN V72G-3AK-NMN * Do not use these valves to relieve pressures outside of the specified ranges. Operation Options - Select the desired relief valve from the preceding order table, then change the model number as shown in the following diagram to obtain the desired option. Also see Product Numbering Chart on page 83 for additional options. Optional Threads B ISO Rc taper G ISO G parallel Optional Adjustment T T-handle V72G - - Optional Gauge G With gauge Service Kits Diaphragm and seal kit: 29-3 For accessories see pages 72 thru Littleton, CO USA Phone Fax /98

39 Inlet Pressure bar,d psid V72G Technical Data Fluid: Compressed air Operating Temperature*: to 15 F (-18 to 5 C) *Air supply must be dry enough to avoid ice formation at temperatures below 35 F (2 C). Gauge Port: 1/8" PTF with PTF main ports 1/8" ISO Rc with ISO Rc main ports 1/8" ISO Rc with ISO G main ports Relief Ports: 1/" NPT with NPT inlet ports ISO G with ISO G inlet ports ISO Rc with ISO Rc inlet ports Materials Body: Zinc Bonnet: Acetal Valve: Brass Elastomers: Neoprene Performance Characteristics Relief Curve, V72 Port Size: 1/" Range: 5. to 15 psig (.3 to 1 bar) scfm Relief Air Flow dm 3 /s Dimensions in Inches (mm) 2.8 (3) 1.1 (2) 2.88 (73) 1.1 (2).3 (12) 1.38 (35) 1.38 (35) 1.91 (8) 1.91 (8) 1.98 (5).98 (25) 1.98 (5).98 (25) 1/" relief port 1/" relief port 1/98 Littleton, CO USA Phone Fax

40 V7G Pressure Relief Valve 3/8", 1/2", and 3/" Port SIzes Excelon design allows in-line or modular installation with other 72, 73, and 7 Series products. Helps protect air operated equipment from over pressure by retarding excessive pressure build up. Low torque, non-rising pressure adjustment knob or sturdy T-handle provides easy hand adjustment at any pressure. The knob has an integral locking device which can be made tamper resistant with the addition of a tamper resistant kit. Ordering Information ISO Symbol Standard Models Model Numbers - Without gauge. Relief Pressure Adjustment Range * Port Knob Adjustment Knob Adjustment T-Handle Adjustment** Size Weight 5 to psig 5 to 15 psig 1 to 25 psig PTF lbs. kg (.3 to bar) (.3 to 1 bar) (.7 to 17 bar) 3/8" 1.53 (.9) V7G-3AK-NFN V7G-3AK-NMN V7G-3AT-NSN 1/2" 1.5 (.8) V7G-AK-NFN V7G-AK-NMN V7G-AT-NSN 3/" 1.7 (.7) V7G-AK-NFN V7G-AK-NMN V7G-AT-NSN * Relief valve can be adjusted to relieve at pressures in excess of, and less than, those specified. Do not use these valves to relieve pressures outside of the specified ranges. ** Relief valves with the 25 psig spring are not available with the knob adjustment. Operation Options - Select the desired relief valve from the preceding order table, then change the model number as shown in the following diagram to obtain the desired option. Also see Product Numbering Chart on page 83 for additional options. Optional Threads B ISO Rc taper G ISO G parallel Optional Adjustment T T-handle V7G - - Optional Gauge G With gauge Service Kits Diaphragm and seal kit: 38-7 For accessories see pages 72 thru 75. Littleton, CO USA Phone Fax /98

41 Inlet Pressure bar,g psig V7G Technical data Fluid: Compressed air Maximum Pressure: 3 psig (2 bar) Temperature Range*: to 175 F (-18 to 79 C). *Air supply must be dry enough to avoid ice formation at temperatures below 35 F (2 C). Gauge ports: 1/" PTF with PTF main ports. 1/" ISO Rc with ISO Rc main ports. 1/8" ISO Rc with ISO G main ports. Performance Characteristics Relief Curve, V7 Port Size: 1/2" Relief Spring Adjustment Range: 5. to 15 psig Materials Body: Aluminum Bonnet: Aluminum Valve: Aluminum, nitrile Elastomers: Neoprene Bottom Plug: Acetal scfm dm 3 /s Relief Flow Dimensions in Inches (mm) Panel mounting hole diameter: 2." (52mm) Panel thickness:." to.25" (2 to mm) 1.5 (37) 2.89 (7) 1.5 (37) 2.89 (7) 2.2 (5) 2.2 (5) 3.15 (8) 3.15 (8) 1.9 (3) 1.9 (3).98 (127) 5.95 (151) 1/98 Littleton, CO USA Phone Fax

42 T72 Lockout & Shut-off Valves 1/" and 3/8" Port Sizes EXCELON design allows in-line or modular installation with other 72, 73, and 7 Series products Valves can be quickly closed by manually pushing the slide. Valves can be locked in closed position only. T72E 3-port/2-position lockout valves help conform to OSHA Lockout Regulations. Valves block inlet air flow and exhaust downstream air in the closed position. Exhaust outlet is not tapped (yellow slide) T72B 2-port/2-position shutoff valves block inlet air flow in the closed position but do not exhaust downstream air (black slide). T72T 3-port/2-position shutoff valves block inlet air flow and exhaust downstream air in the closed position. Exhaust port is tapped (red slide). Valves can be quickly closed by manually pushing the slide. Valves can be locked in the closed position only with a customer supplied padlock. ISO Symbols Ordering Information Standard Models Lockout valve, Shut-off valve, Shut-off valve, Port yellow slide, black slide, red slide, Size Weight 3-Port/2-position 2-port/2-position 3-port/2-position PTF lbs.(kg) Unthreaded exhaust No exhaust outlet Threaded exhaust port 1/".79 (.3) T72E-2AA-P1N T72B-2AA-P1N T72T-2AA-P1N 3/8".79 (.3) T72E-3AA-P1N T72B-3AA-P1N T72T-3AA-P1N 2-Port/2-Position Operation 3-Port/2-Position Options - Select the desired shutoff valve from the preceding order table, then change the model number as shown in the following diagram to obtain the desired option. Also see Product Numbering Chart on page 8 for additional options. IN OUT IN OUT T72 - A - P1N Optional Threads for T72 Shutoff Valves B ISO Rc taper G ISO G parallel 2-Port/2-Position Service Kits (includes seals and slide) Type Part Number T72E (yellow slide) T72B (black slide) T72T (red slide) IN OUT IN OUT EXHAUST 3-Port/2-Position For accessories see pages 72 thru Littleton, CO USA Phone Fax /98

43 T72 Technical Data Fluid: Compressed air Maximum Inlet Pressure: 25 psig (17 bar) Operating Temperature*: to 15 F (-2 to 5 C) *Air supply must be dry enough to avoid ice formation at temperatures below 2 C (35 F.) Cv factor from IN to OUT ports: 5.7 * Optional threaded exhaust port 1-32 Maximum diameter of customer supplied padlock shackle: 3/1" (5 mm) Dimensions in inches (mm) 1.98 (5) 1.91 (8) *Cv factor from OUT to EXHAUST ports on 3-port/2-position valves is.2. Materials Body: Zinc Slide: Acetal plastic Elastomers: Nitrile 3. (88) 1/98 Littleton, CO USA Phone Fax

44 T73 Lockout & Shut-off Valves 1/", 3/8", 1/2" Port Sizes EXCELON design allows in-line or modular installation with other 72, 73, and 7 Series products Valves can be quickly closed by manually pushing the slide. Valves can be locked in closed position only. T73E 3-port/2-position lockout valves help conform to OSHA Lockout Regulations. Valves block inlet air flow and exhaust downstream air in the closed position. Exhaust outlet is not tapped (yellow slide) T73B 2-port/2-position shutoff valves block inlet air flow in the closed position but do not exhaust downstream air (black slide). T73T 3-port/2-position shutoff valves block inlet air flow and exhaust downstream air in the closed position. Exhaust port is tapped (red slide). Valves can be quickly closed by manually pushing the slide. Valves can be locked in the closed position only with a customer supplied padlock. ISO Symbols Ordering Information Standard Models Lockout valve, Shut-off valve, Shut-off valve, Port yellow slide black slide red slide Size Weight 3-Port/2-position, 2-port/2-position, 3-port/2-position, PTF lbs.(kg) Unthreaded exhaust no exhaust outlet threaded exhaust port 1/".7 (.3) T73E-2AA-P1N T73B-2AA-P1N T73T-2AA-P1N 3/8".7 (.3) T73E-3AA-P1N T73B-3AA-P1N T73T-3AA-P1N 1/2".7 (.3) T73E-AA-P1N T73B-AA-P1N T73T-AA-P1N Operation 2-Port/2-Position 3-Port/2-Position Options - Select the desired shutoff valve from the preceding order table, then change the model number as shown in the following diagram to obtain the desired option. Also see Product Numbering Chart on page 8 for additional options. T73 - A - P1N Optional Threads for T73 Shutoff Valves B ISO Rc taper G ISO G parallel IN OUT IN 2-Port/2-Position OUT Service Kits (includes seals and slide) Type Part Number T73E (yellow slide) T73B (black slide) 38-1 T73T (red slide) IN OUT IN OUT EXHAUST 3-Port/2-Position For accessories see pages 72 thru 75. Littleton, CO USA Phone Fax /98

45 T73 Technical Data Fluid: Compressed air Maximum pressure: 25 psig (17 bar) Operating temperature*: to +15 F (-2 to +5 C) *Air supply must be dry enough to avoid ice formation at temperatures below 35 F (2 C). Cv factor: IN to OUT ports: 1/" ports:. 3/8" ports: 8. 1/2" ports: 7.8 OUT to EXHAUST ports on 3-port/2-position valves:.2 Exhaust port threads on T73T models: 1-32 Maximum diameter of customer supplied padlock shackle: 5/1" (8 mm) Materials Body: Zinc Slide: Acetal plastic Elastomers: Nitrile Dimensions in Inches (mm) 2.13 (5) 88 (3.) 2.32 (59) 1/98 Littleton, CO USA Phone Fax

46 T7 Lockout & Shut-off Valves 3/8", 1/2", and 3/" EXCELON design allows in-line or modular installation with other 72, 73, and 7 Series products Valves can be quickly closed by manually pushing the slide. Valves can be locked in closed position only. T7E 3-port/2-position lockout valves help conform to OSHA Lockout Regulations. Valves block inlet air flow and exhaust downstream air in the closed position. Exhaust outlet is not tapped (yellow slide) T7B 2-port/2-position shutoff valves block inlet air flow in the closed position but do not exhaust downstream air (black slide). T7T 3-port/2-position shutoff valves block inlet air flow and exhaust downstream air in the closed position. Exhaust port is tapped (red slide). Valves can be quickly closed by manually pushing the slide. Valves can be locked in the closed position only with a customer supplied padlock. Ordering Information Standard Models (PTF threads) Port Lockout valve, Yellow Shut-off valve, Black Shut-off valve, Red Size Weight 3-Port/2-position, 2-Port/2-position, 3-Port/2-position, PTF lbs. (kg) unthreaded exhaust no exhaust outlet threaded exhaust port 3/8".9 (.32) T7E-3AA-P1N T7B-3AA-P1N T7T-3AA-P1N 1/2".5 (.3) T7E-AA-P1N T7B-AA-P1N T7T-AA-P1N 3/".2 (.28) T7E-AA-P1N T7B-AA-P1N T7T-AA-P1N ISO Symbol 2-Port/2-Position Operation 3-Port/2/Position Options - Select the desired shutoff valve from the preceding order table, then change the model number as shown in the following diagram to obtain the desired option. Also see Product Numbering Chart on page 8 for additional options. IN OUT IN OUT T7 - A - P1N Optional Threads for T7 Shutoff Valves B ISO Rc taper G ISO G parallel 2-Port/2-Position N OUT IN OUT Service Kits (includes seals and slide) Type Part Number T7E (yellow slide) T7B (black slide) T7T (red slide) Port/2-Position For accessories see pages 72 thru 75. EXHAUST Littleton, CO USA Phone Fax /98

47 T7 Technical Data Fluid: Compressed air Maximum Inlet Pressure: 25 psig (17.2 bar) Operating Temperature: to 15 F (-2 to C) Exhaust port threads on T7T Shut-Off valves: 1/8-27 PTF with PTF main ports 1/8-28 ISO Rc with ISO G and ISO Rc main ports Cv factor: IN to OUT ports: 3/8" ports: 7.1 1/2" ports: 8.1 3/" ports: 7.7 OUT to EXHAUST ports on 3-port/2-position valves:.2 Maximum diameter of customer supplied padlock shackle: 5/1" (8 mm) 1.55 (39) OPEN Dimensions in Inches (mm) 1.22 (31) 2.9 (7) 2.7(7) Materials Body: Zinc Slide: Acetal plastic Elastomers: Nitrile 1/98 Littleton, CO USA Phone Fax

48 72 Series Combination Units Filters 1/" and 3/8" Port Sizes EXCELON design allows in-line or modular installation with other 72, 73, and 7 Series products F72G pre filter and F72C oil removal filter provide high efficiency oil removal and particle removal to.1 µm. Pre filter removes particulate to 5µm. Coalescing filter removes particles down to.1 µm. Maximum remaining oil content of air leaving the filter is.1 ppm at 7 F (21 C) with an inlet concentration of 17 ppm. Provides air quality within ISO : Class Service indicator turns from green to red when the filter element needs to be relaced. Highly visible, prismatic liquid level indicator lens. Quick release bayonet bowl. Patented quarter turn manual drain. Ordering Information Standard Models General Purpose & Coalescing Filters: Automatic drain, 2.2 oz. transparent bowl, and service life indicator, 5µm filter on inlet. Port Model Number - Inline Units Size Body and General Purpose & PTF Element Coalescing Filters 1/" Standard H72A-2AB-AL1-NNN-LNN 3/8" Standard H72A-3AB-AL1-NNN-LNN Options - Select the desired combination unit from the preceding order table, then change the model number as shown in the following diagram to obtain the desired option. Also see Product Numbering Chart on page 85 for additional options. 72A NNN - N Optional Lockout Valve and Quikmount Pipe Adapters H Filter-Filter (standard) J Lockout valve on inlet of combination. M Quikmount pipe adapters. N Lockout valve on inlet and Quikmount pipe adapter on outlet. Port Size 2 1/" 3 3/8" Optional Threads B ISO Rc Taper G ISO G Parallel Service Indicator Options B Service indicator on both filters. C Service indicator only on coalescing filter. D Service indicator only on general purpose filter. N No service indicator. Quikclamp Wall Mounting Brackets B With brackets N Without Coalescing Filter Bowl D 1.9 oz. metal with liquid level indicator* W 2.2 oz. transparent with guard General Purpose Filter Bowl D 1.9 oz. metal with liquid level indicator* W 2.2 oz. transparent with guard General Purpose and Oil Removal Filter Drain Options Q 1/ turn manual S Semiautomatic ISO Symbols Semiautomatic and Automatic drains Operation General Purpose Coalescing Manual drain *Auto drain not available with D bowl option. For other bowl options (shorter and lower 1.9 oz. capacity) consult factory. Service Kits, Specifications, Materials, and Performance. See filter pages, 7, 12, and 13. For accessories see pages 72 thru Littleton, CO USA Phone Fax /98

49 72 Series Combination Units Filters Dimensions in Inches (mm) See pages 7 and 13 for dimensions on individual units. The optional Quikclamp wall mounting bracket is illustrated on the following combination units. H72 Combination Units (Listed in Order Table) J72 Combinations with Lockout Valve (See Alternative Models).22 (18) 2.11 (5) 2.11 (5). (1) 2.11 (5) 2.2 (5) 2.11 (5) 2.32 (59) 2.32 (59) M72 Combinations with Quikmount Pipe Adapters (See Alternative Models). (152) N72 Combinations with Lockout Valve and Quikmount Pipe Adapter (See Alternative Models) 7.35 (187).8 (113) 2.11 (5).8 (113) 2.32 (59) 2.32 (59) 1/98 Littleton, CO USA Phone Fax

50 EXCELON design allows in-line or modular installation with other 72, 73, and 7 Series products F73G pre filter and F73C oil removal filter provide high efficiency oil removal and particle removal to.1 µm. Pre filter removes particulate to 5µm. Coalescing filter removes particles down to.1 µm. Maximum remaining oil content of air leaving the filter is.1 ppm at 7 F (21 C) with an inlet concentration of 17 ppm. Provides air quality within ISO : Class Service indicator turns from green to red when the filter element needs to be relaced. Highly visible, prismatic liquid level indicator lens. Quick release bayonet bowl. Patented quarter turn manual drain. 73 Series Combination Units Filters 1/", 3/8", 1/2" Port Sizes Ordering Information Standard Models General Purpose & Coalescing Filters: Automatic drains, metal bowl with liquid level indicator, and service life indicator, 5µm filter on inlet. Port Model Number - Inline Units Size Body and General Purpose & PTF Element Coalescing Filters 1/" Standard H73A-2AB-AD1-NNN-DNN 3/8" Standard H73A-3AB-AD1-NNN-DNN 1/2" Standard H73A-AB-AD1-NNN-DNN Options - Select the desired combination unit from the preceding order table, then change the model number as shown in the following diagram to obtain the desired option. Also see Product Numbering Chart on page 85 for additional options. 73A NNN - N Optional Lockout Valve and Quikmount Pipe Adapters H Filter-Filter (standard) J Lockout valve on inlet of combination. M Quikmount pipe adapters. N Lockout valve on inlet and Quikmount pipe adapter on outlet. Port Size 2 1/" 3 3/8" 1/2" Optional Threads B ISO Rc Taper G ISO G Parallel Service Indicator Options B Service indicator on both filters. C Service indicator only on coalescing filter. D Service indicator only on general purpose filter. N No service indicator. Quikclamp Wall Mounting Brackets B With brackets N Without Coalescing Filter Bowl D Metal with liquid level indicator P Transparent with metal guard T Transparent General Purpose Filter Bowl D Metal with liquid level indicator P Transparent with guard T Transparent General Purpose, and Oil Removal Filter Drains Q 1/ turn manual A Automatic Service Kits, Specifications, Materials, Performance, and Unit Dimensions - See filter pages thru 15. ISO Symbols Automatic Drain Manual Drain Operation General Purpose Coalescing For accessories see pages 72 thru Littleton, CO USA Phone Fax /98

51 See pages 7 and 15 for dimensions on individual units. Standard Type H73A- Shown with optional Quikclamp wall bracket. 73 Series Combination Units Filters Dimensions in Inches (mm) Alternative Type J73A-Includes Lockout Valve Shown with optional Quikclamp wall brackets (75) 2.95 (75) 2. (1) 3.23 (82) 2.95 (75) 5.91 (15) 8.58 (218) Alternative Type M73A- Includes Quikmount Pipe Adapters Shown with optional Quikclamp wall brackets. Alternative Type N73A- Includes Lockout Valve and Quikmount Pipe Adapters Shown with optional Quikclamp wall brackets..2 (13) 2. (1).2 (13) 8.39 (213) 9.8 (29) 1/98 Littleton, CO USA Phone Fax

52 7 Series Combination Units Filters 3/8", 1/2", and 3/" Port Sizes EXCELON design allows in-line or modular installation with other 72, 73, and 7 Series products F7G pre filter and F7C oil removal filter provide high efficiency oil removal and particle removal to.1 µm. Pre filter removes particulate to 5µm. Coalescing filter removes particles down to.1 µm. Maximum remaining oil content of air leaving the filter is.1 ppm at 7 F (21 C) with an inlet concentration of 17 ppm. Provides air quality within ISO : Class F7C and F7V combinations provide air quality within ISO : Class Service indicator turns from green to red when the filter element needs to be relaced. Highly visible, prismatic liquid level indicator lens. Quick release bayonet bowl. Patented quarter turn manual drain. Ordering Information Standard Models General Purpose Coalescing Filters: Metal bowl with liquid level indicator, automatic drains, and service life indicators. Adsorbing filter: Metal bowl, without liquid level indicator, closed bottom. Model Number - Inline Units Port General Purpose & General Purpose, Size Body and Coalescing Coalescing & Adsorbing PTF Element Filters Filters 3/8" Standard H7A-3AB-AD1-NNN-DNN H7F-3AB-AD1-NNN-DMN 1/2" Standard H7A-AB-AD1-NNN-DNN H7F-AB-AD1-NNN-DMN 1/2" High Flow H7B-AB-AD1-NNN-DNN 3/" High Flow H7B-AB-AD1-NNN-DNN ISO Symbols Operation Automatic Drain Manual Drain General Purpose Coalescing Adsorbing Options - Select the desired combination unit from the preceding order table, then change the model number as shown in the following diagram to obtain the desired option. Also see Product Numbering Chart on page 85 for additional options NNN - M Optional Lockout Valve and Quikmount Pipe Adapters H Filter-Filter (standard) J Lockout valve on inlet of combination. M Quikmount pipe adapters. N Lockout valve on inlet and Quikmount pipe adapter on outlet. Optional Threads B ISO Rc Taper G ISO G Parallel Optional Quikclamp Wall Mounting Brackets B With brackets Optional Bowl (Coalescing Filter) P Transparent with guard Optional Bowl (General Purpose Filter) P Transparent with guard Optional Manual Drain (General Purpose, Coalescing Filters) Q 1/ turn manual Service Indicator Options C Service indicator only on coalescing filter. D Service indicator only on general purpose filter. N No service indicator. Service Kits, Specifications, Materials, Performance, and Unit Dimensions - See filter pages thru 18. For accessories see pages 72 thru Littleton, CO USA Phone Fax /98

53 See pages 11, 17 and 19 for dimensions on individual units. Standard Combination Units Shown with optional Quikclamp wall mounting brackets. H Series Combination Units Filters Dimensions in Inches (mm) Optional Combinations with Lockout Valve Shown with optional Quikclamp wall mounting brackets. J Two Units 3.2 (87) 3.2 (87) Three Units 3.2 (87) 3.8 (9) 3.2 (87) Two Units 3.3 (77) 3.8 (9) 3.2 (87) Three Units 3.3 (77) 7.37 (187) 3.2 (87).8 (17) 1.52 (27) 1.13 (257) (351) Optional Combinations with Quikmount Pipe Adapters Shown with optional Quikclamp wall mounting brackets. M Optional Combinations with Lockout Valve and Quikmount Pipe Adapter - Shown with optional Quikclamp wall mounting brackets. N Two Units 7.37 (187) Three Units 11.5 (281) Two Units 7.37 (187) Three Units 11.5 (281) 3.3 (77) 3.3 (77) 9.32 (237) (289) (33) 15.5 (382) 1/98 Littleton, CO USA Phone Fax

54 72 Series F-R-L Combination Units 1/" and 3/8" Port Sizes EXCELON design allows in-line or modular installation with other 72, 73, and 7 Series products High efficiency water and particle removal. Particle removal within ISO : Class 3 and 5. Regulator balanced valve minimizes effect of variation in the inlet pressure on the outlet pressure. Micro-Fog or Oil-Fog models available. Quick release bayonet bowl. Highly visible, prismatic liquid level indicator lens. Ordering Information Standard Models Filter/Regulator (F/R) and Regulator (R) listed in table are relieving type with knob adjustment, 15 psig (1 bar) regulating spring,* and a gauge. Filter/Regulator (F/R) and Filter (F) listed in table include an automatic drain, transparent bowl, and a µm element. Lubricator (L) listed in table is an Micro-Fog model with manual drain and a transparent bowl. Port Model Numbers Size Filter/Regulator-Lubricator Filter-Regulator-Lubricator Filter-Lubricator PTF (Two Unit F/R-L) (Three Unit F-R-L) (Two Unit F-L) 1/" C72H-2AK-AL3-RMG-QLN C72A-2AK-AL3-RMG-QLN C72C-2AN-AL3-NNN-QLN 3/8" C72H-3AK-AL3-RMG-QLN C72A-3AK-AL3-RMG-QLN C72C-3AN-AL3-NNN-QLN *Do not use these units to control pressures outside of the specified ranges. Options - Select the desired combination unit from the preceding order table, then change the model number as shown in the following diagram to obtain the desired option. Also see Product Numbering Chart on page 8 for additional options Q Optional Lockout Valve and Optional Quikclamp Wall Brackets Quikmount Pipe B With brackets D Lockout Valve on inlet of combination Optional Lubricator Reservoir** E Quikmount pipe adapters D 1.9 oz. metal with liquid level G Lockout valve on inlet and indicator Quikmount pipe adapter on W 2.2 oz. transparent with guard outlet. Optional Lubricator and Porting Block Optional Regulator and J Oil-Fog F/R-L Combination Filter/Regulator Gauge B Oil-Fog F-R-L Combination N Without gauge D Oil-Fog F-L Combination K Optional Regulator and Filter/Regulator L Micro-Fog F/R-L Combination with porting block between filter/regulator and lubricator. OIL-FOG F/R-L Combination with porting block between filter/regulator and lubricator Optional Threads B ISO Rc Taper G ISO G Parallel Optional Regulator and Filter/Regulator Adjustment T T-bar Optional Filter and Filter/Regulator Drain S Semiautomatic Q Manual, 1/ turn Outlet Pressure Adjustment Range* F 5 to psig (.3 to bar) Optional Regulator and Filter/Regulator Diaphragm N Nonrelieving Optional Filter and Filter/Regulator Element 1 5µm Optional Filter and Filter/Regulator Bowl** D 1.9 oz. metal with liquid level indicator W 2.2 oz. transparent with guard ISO Symbols See preceding pages on general purpose filters (page ), regulators (page 1), filter/regulators (pages 1) and lubricators (pages 2). Operation Filter Regulator Micro-Fog Lubricator Service Kits, Specifications, Materials and Performance See preceding pages on general purpose filters (pages and 7), regulators (pages 1 and 17), filter/regulators (pages 2 and 21) and lubricators (pages 2 and 25). For accessories see pages 72 thru 75. **Automatic drain not available with D bowl option. For other bowl options (shorter and lower 1.9 oz. capacity) consult factory. 5 Littleton, CO USA Phone Fax /98

55 See pages 7, 21 and 33 for dimensions on individual units. C72 Combination Units (Listed in Order Table) Two Three Units.22 (18) Units 2.11 (5) 2.11 (5) 2.11 (5). (1) 2.2 (5) 2.11 (5) 72 Series F-R-L Combination Units D72 Combinations with Lockout Valve (See Alternative Models) Two Units 2.11 (5). (1) 2.2 (5) 2.11 (5) Dimensions in Inches (mm) Three Units 2.11 (5) 8.7 (221).8 (113) 2.11 (5) 2.32 (59) 2.32 (59) 2.32 (59) 2.32 (59) E72 Combinations with Quikmount Pipe Adapters (See Alternative Models) Two Units Three Units G72 Combinations with Lockout Valve and Quikmount Pipe Adapter (See Alternative Models) Two Units Three Units 2.11 (5). (1) 2.2 (5) 2.11 (5) 8.2 (29).72 (171) 2.11 (5) 7.35 (187).8 (113) 2.11 (5) 9.59 (2).72 (171) 2.32 (59) 2.32 (59) 2.32 (59) 2.32 (59) C72L Combination Units with Porting Block (See Alternative Models) D72L Combination Units with Porting Block and Lockout Valve (See Alternative Models) E72L Combination Units with Porting Block and Quikmount Pipe Adapters (See Alternative Models) G72L Combination Units with Porting Block, Lockout Valve and Quikmount Pipe Adapter (See Alternative Models) 2.11 (5) 5.1 (13) 1.39 (35) 2.11 (5) 7.85 (2) 2.11 (5) 3.3 (92) 2.11 (5) 7.39 (188) 5.87 (19) 8.7 (222) 2.11 (5) 5.87 (19) 2.32 (59) 2.32 (59) 2.32 (59) 2.32 (59) C72P Combination Units with Porting Block (See Alternative Models) D72P Combination Units with Porting Block and Lockout Valve (See Alternative Models) E72P Combination Units with Porting Block and Quikmount Pipe Adapters (See Alternative Models) G72P Combination Units with Porting Block, Lockout Valve and Quikmount Pipe Adapter (See Alternative Models) 2.11 (5) 7.85 (2) 3.3 (92) 2.11 (5) 1.9 (257) 9.3 (25) 1.98 (279) 2.11 (5) 5.87 (19) 2.11 (5) 8.11 (2) 2.11 (5) 8.11 (2) 2.32 (59) 2.32 (59) 2.32 (59) 2.32 (59) 1/98 Littleton, CO USA Phone Fax

56 EXCELON design allows in-line or modular installation with other 72, 73, and 7 Series products High efficiency water and particle removal. Particle removal within ISO : Class 3 and 5. Regulator balanced valve minimizes effect of variation in the inlet pressure on the outlet pressure. Micro-Fog or Oil-Fog models available. Quick release bayonet bowl. Highly visible, prismatic liquid level indicator lens. 73 Series F-R-L Combination Units 1/", 3/8", 1/2" Port Sizes Ordering Information Standard Models Filter/Regulator (F/R) and Regulator (R) listed in table are relieving type with knob adjustment, 15 psig (1 bar) regulating spring,* and a gauge. Filter/Regulator (F/R) and Filter (F) listed in table include an automatic drain, metal bowl with liquid level indicator, and a µm element. Lubricator (L) listed in table is an Micro-Fog model with manual drain and a metal bowl with liquid level indicator. Port Model Numbers Size Filter/Regulator-Lubricator Filter-Regulator-Lubricator Filter-Lubricator PTF (Two Unit F/R-L) (Three Unit F-R-L) (Two Unit F-L) 1/" C73H-2AK-AD3-RMG-QDN C73A-2AK-AD3-RMG-QDN C73C-2AN-AD3-NNN-QDN 3/8" C73H-3AK-AD3-RMG-QDN C73A-3AK-AD3-RMG-QDN C73C-3AN-AD3-NNN-QDN 1/2" C73H-AK-AD3-RMG-QDN C73A-AK-AD3-RMG-QDN C73C-AN-AD3-NNN-QDN Options - Select the desired combination unit from the preceding order table, then change the model number as shown in the following diagram to obtain the desired option. Also see Product Numbering Chart on page 8 for additional options. ISO Symbols See preceding pages on general purpose filters (page 8), regulators (page 18), filter/regulators (pages 22) and lubricators (pages 2). Operation Filter Regulator Micro-Fog Lubricator Optional Lockout Valve and Quikmount Pipe D Lockout Valve on inlet of combination E Quikmount pipe adapters G Lockout valve on inlet and Quikmount pipe adapter on outlet. Optional Lubricator and Porting Block J Oil-Fog F/R-L Combination B Oil-Fog F-R-L Combination D Oil-Fog F-L Combination K Micro-Fog F/R-L Combination with porting block between filter/regulator and lubricator. L OIL-FOG F/R-L Combination with porting block between filter/regulator and lubricator Optional Threads B ISO Rc Taper G ISO G Parallel Optional Regulator and Filter/Regulator Adjustment T T-bar Q Optional Quikclamp Wall Brackets B With brackets Lubricator Reservoir P...Transparent with guard T...Transparent Optional Regulator and Filter/Regulator Gauge N Without gauge Optional Regulator and Filter/Regulator Outlet Pressure Adjustment Range* F 5 to psig (.3) to bar) S 1 to 25 psig (.7 to 17 bar) Optional Regulator and Filter/Regulator Diaphragm N Nonrelieving Optional Filter and Filter/Regulator Element 1 5µm Service Kits, Specifications, Materials, and Performance. See pages, 7, 12, and 13. Optional Filter and Filter/Regulator Drain Q Manual, 1/ turn Optional Filter and Filter/Regulator Bowl P...Transparent with guard T...Transparent without guard For accessories see pages 72 thru 75. *Do not use these units to control pressures outside of the specified ranges. 5 Littleton, CO USA Phone Fax /98

57 See pages 9, 23, and 35 for dimensions on individual units. 73 Series F-R-L Combination Units Dimensions in Inches (mm) Standard Micro-Fog Type C73A- Standard Oil-Fog Type C73B- Shown with optional gauge and Quikclamp wall bracket (75) 3.23 (82) 2.95 (75) Alternative Micro-Fog Type D73A- Alternative Oil-Fog Type D73B- Includes lockout valve. Shown with optional gauge and Quikclamp wall bracket. 2. (1).2 (13) 2.95 (75) 9.13 (232) (299) Alternative Micro-Fog Type E73A- Alternative Oil-Fog Type E73B- Includes Quikmount pipe adapters. Shown with optional gauge and Quikclamp wall bracket. 9.5 (25) Alternative Micro-Fog Type G73A- Alternative Oil-Fog Type G73B- Includes lockout valve and Quikmount pipe adapter. Shown with optional gauge and Quikclamp wall bracket. 2. (1) 9.5 (25) (29) (33) 1/98 Littleton, CO USA Phone Fax

58 7 Series Combination F-R-L Units 3/8", 1/2", and 3/" Port Sizes EXCELON design allows in-line or modular installation with other 72, 73, and 7 Series products High efficiency water and particle removal. Particle removal within ISO : Class 3 and 5. Regulator balanced valve minimizes effect of variation in the inlet pressure on the outlet pressure. Micro-Fog or Oil-Fog models available. Quick release bayonet bowl. Highly visible, prismatic liquid level indicator lens. Ordering Information Standard Models Regulator and Filter/Regulator: Knob adjustment, relieving, 15 psig spring, gauge. Filter and Filter/Regulator: Automatic drain, metal bowl with liquid level indicator, µm element. Lubricator: Micro-Fog, manual drain, 7-ounce metal bowl with liquid level indicator. Port Model Numbers Size PTF Filter/Regulator-Lubricator Filter-Regulator-Lubricator Filter-Lubricator 3/8" C7H-3AK-AD3-RMG-QDN C7A-3AK-AD3-RMG-QDN C7C-3AN-AD3-NNN-QDN 1/2" C7H-AK-AD3-RMG-QDN C7A-AK-AD3-RMG-QDN C7C-AN-AD3-NNN-QDN 3/" C7H-AK-AD3-RMG-QDN C7A-AK-AD3-RMG-QDN C7C-AN-AD3-NNN-QDN Options - Select the desired combination unit from the preceding order table, then change the model number as shown in the following diagram to obtain the desired option. Also see Product Numbering Chart on page 8 for additional options Q Optional Lockout Valve and Quikmount Pipe Adapters D Lockout valve on inlet of combination. E Quikmount pipe adapters. G Lockout valve on inlet and Quikmount pipe adapter on outlet. Optional Lubricator and Porting Block J Oil-Fog F/R-L Combination B Oil-Fog F-R-L Combination D Oil-Fog F-L Combination K Micro-Fog F/R-L Combination with porting block between filter/regulator and lubricator. L Oil-Fog F/R-L Combination with porting block between filter/regulator and lubricator. Optional Threads B ISO Rc Taper G ISO G Parallel Optional T-Handle Pressure Adjustment T T-handle (Required with the optional 25 psig regulating spring) Optional Element 1 5µm Optional Quikclamp Wall Mounting Brackets B With brackets Optional Lubricator Reservoir P 7-oz. transparent with metal guard Standard Gauge N...Without gauge Optional Regulating Springs F 5 to psig (.3 to bar) S 1 to 25 psig (1 to 17 bar) - The S spring option requires the optional T-handle adjustment and a metal reservoir on the lubricator. Optional Diaphragm N Nonrelieving Optional Bowl (Filter,Filter/Regulator) P Transparent with metal guard Optional Drain (Filter, Filter/Regulator) Q 1/ turn manual ISO Symbols See preceding pages on general purpose filters (page 8), regulators (page 18), filter/regulators (pages 22) and lubricators (pages 2). Operation Filter Regulator Micro-Fog Lubricator Service Kits, Specifications, Materials and Performance See preceding pages on general purpose filters (pages 8 and 9), regulators (pages 18 and 19), filter/regulators (pages 22 and 23) and lubricators (pages 2 and 27). For accessories see pages 72 thru Littleton, CO USA Phone Fax /98

59 See pages 11, 25, and and 37 for dimensions on individual units. 7 Series Combination F-R-L Units Dimensions in Inches (mm) Standard Combination Units Shown with optional Quikclamp wall mounting brackets. C Optional Combinations with Lockout Valve Shown with optional Quikclamp wall mounting brackets. D Two Units 3.2 (87) 3.2 (87) Three Units 3.2 (87) 3.8 (9) 3.2 (87) Two Units 3.3 (77) 3.8 (9) 3.2 (87) Three Units 3.3 (77) 7.37 (187) 3.2 (87).8 (17) 1.52 (27) 1.13 (257) (351) Optional Combinations with Quikmount Pipe Adapters Shown with optional Quikclamp wall mounting brackets. E Optional Combinations with Lockout Valve and Quikmount Pipe Adapter - Shown with optional Quikclamp wall mounting brackets. G Two Units 9.2 (23) Three Units 3.3 (77) 9.2 (23) Two Units 3.3 (77) 7.37 (187) Three Units 3.3 (77) 11.5 (281) 11.1 (283) 13.2 (335) (289) 15.5 (382) Combination Units with Porting Block Shown with optional Quikclamp wall mounting brackets. Standard Combinations C (87) 1.85 (7) 3.2 (87) Combinations With Lockout Valve D (77) 5.52 (1) 3.2 (87) Combinations With Quikmount Pipe Adapters E (23) Combinations With Lockout Valve and Quikmount Pipe Adapter G (77) 9.2 (23) 8.9 (221) (3) 11.1 (283) 13.2 (335) 1/98 Littleton, CO USA Phone Fax

60 P7 Solenoid Operated Directional Control Valves EXCELON design allows in-line or modular installation with other 72, 73, and 7 Series products. Inlet and outlet ports are not threaded. High-flow, spring return valves. 2-port/2-position valves available in normally closed or normally open functional modes. The 3-port/2- position valves available normally closed only. Options include various voltages, low watt coils, and electrical connectors. Short stroke, positive sealing cushioned poppets for long service life. Ordering Information Standard Models Model Numbers - Modular installation,12vhz/11v5hz, 7.5 watt solenoid coil, internal pilot supply, manual locking override, cable grip electrical connector. Installation Weight 2-Port/2-Position 2-Port/2-Position 3-Port/2-Position Type lbs. (kg) Normally Closed Normally Open Normally Closed Modular 1.3 (.7) P7A-NNC-SJA P7B-NNC-SJA P7C-NAC-SJA Options - Select the desired valve from the preceding order table, then change the model number as shown in the following diagram to obtain the desired option. Also see Product Numbering Chart on page 87 for additional options. 7.5 Watt Coils L = 2 VAC K = 2 VAC Q = 12 VDC P = 2 VDC P7 - NNC - S 3.5 Low Watt Coils C = 2 VAC A = 12 VAC D = VDC E = 12 VDC F = 2 VDC B = Cable grip with indicator lights ISO Symbols 2-Port/2-Position 2-Port/2-Position 3-Port/2-Position Normally Closed Normally Open Normally Closed Operation 2-Port/2-Position Normally Closed 2-Port/2-Position Normally Open A (IN) NORMAL Inlet Blocked B (OUT) B (OUT) A (IN) ACTUATED B (OUT) Pressure to Port B B (OUT) Service Kits Seal and gasket kit: Moisture resistant connector seal: Coil retaining clip: Solenoid exhaust port diffuser: 53-1 * For valves with threaded ports, see NCA-12. A (IN) 3-Port/2-Position Normally Closed B (IN) Pressure to Port B Inlet Blocked A (OUT) A (IN) Inlet Blocked B (IN) A (OUT) Pressure to Port A For accessories see pages 72 thru 75. Littleton, CO USA Phone Fax /98

61 P7 Dimensions in inches (mm) Technical Data Fluids: Filtered and lubricated compressed air. Main valve inlet pressure range: 3 to 15 psig (2.1 to 1.3 bar) Operating Temperature*: -18 to 12 F (-28 to 9 C). * Air supply must be dry enough to avoid ice formation at temperatures below 35 F (2 C). Average flow factor (C v ) of 2-port valves:. Average flow factor (C v ) of 3-port valves: In-Out Ports: 2. Out-Exhaust Ports: 5.3 Response times of 3-port valve (elapsed time from solenoid energized to an increase in the main valve pressure): Standard operator: 11 ms at 9 psig Low wattage operator: 13.5 ms at 9 psig Exhaust port on 3-port/2-position valves: 1/2-1 PTF 2-Port/2-Position Valves 2.28 ().12 (15) 3.15 (8) 1.97 (5) Solenoid Operator Electrical Specifications Voltage and power requirements: Wattage Standard Low Watt Voltage Operator Operator 2V/Hz/5Hz V/Hz-11V/5Hz V/Hz-22V/5Hz 7.5 VDC VDC VDC Port/2-Position Valves 2.28 () 1. (37) 3.15 (8) 1.97 (5) Duty: Continuous at 9% to 15% of rated voltage. Coil Type: Molded with three pin plug-in connector. Enclosure Classification: NEMA 1, NEMA and IP 5. Connector Plug: Cable grip for cables 1/" to 5/1" ( to 8 mm) in diameter. Electrical connectors conform to Industry Standard Form B for Three-Pin Electrical Plug Connectors, 11 mm spacing. Override: Manual, locking.3 (13) Materials Body: Zinc Pistons, Poppets: Aluminum Elastomers: Nitrile Operator Housing: PPS Plastic Operator Base: Aluminum Plunger & Spring: Stainless Steel 1.75 (5) 1/98 Littleton, CO USA Phone Fax

62 EXCELON design allows in-line or modular installation with other 72, 73, and 7 Series products. Inlet and outlet ports are not threaded. 2-port/2-position valves available in normally closed or normally open functional modes. The 3-port/2-position valves available only in normally closed mode. Short stroke, positive sealing cushioned poppets for long service life. P7 Directional Control Valves 2-port/2-position and 3-port/2-position Air Operated Directional Control Poppet Valves ISO Symbols Ordering Information Standard Models Model Numbers Installation Weight 2-Port/2-Position 2-Port/2-Position 3-Port/2-Position Type lbs. kg Normally Closed Normally Open Normally Closed Modular 1.2 (.5) P7A-NNA-NNN P7B-NNA-NNN P7C-NAA-NNN See Product Numbering Chart on page 87 for additional options. 2-Port/2-Position 2-Port/2-Position 3-Port/2-Position Normally Closed Normally Open Normally Closed Operation Service Kit Seal and gasket kit: Port/2-Position Normally Closed A (IN) NORMAL B (OUT) A (IN) ACTUATED B (OUT) * For valves with threaded ports, see NCA Port/2-Position Normally Open Inlet Blocked B (OUT) Pressure to Port B B (OUT) A (IN) A (IN) Pressure to Port B Inlet Blocked 3-Port/2-Position Normally Closed B (IN) B (IN) A (OUT) A (OUT) Inlet Blocked Pressure to Port A 2 Littleton, CO USA Phone Fax /98

63 P7 Air Operated Directional Control Valves Dimensions in inches (mm) Technical Data Fluids: Filtered and lubricated compressed air. Main valve inlet pressure range: to 25 psig (17.2 bar). Pilot supply inlet pressure range: Equal to or greater than main valve inlet pressure, but not less than 3 psig (2.1 bar) and not greater than 25 psig (17.2 bar). Operating temperature*: -2 to 13 F (-29 to 5 C). * Air supply must be dry enough to avoid ice formation at temperatures below 35 F (2 C). Average flow factor (C v ) of 2-port valves:. Average flow factor (C v ) of 3-port valves: In-Out Ports: 2. Out-Exhaust Ports: 5.3 Pilot port: 1/-18 PTF Exhaust port on 3-port/2-position valves: 1/2-1 PTF 2-Port/2-Position Valves 2.28 () 3.52 (89) 1. (37) 3.15 (8) Materials Body: Zinc Pistons, Poppets: Aluminum Elastomers: Nitrile Operator: Aluminum 3-Port/2-Position Valves 3.15 (8) 2.28 () 3.83 (97) 1.75 (5) 1/98 Littleton, CO USA Phone Fax

64 EXCELON design allows in-line or modular installation with other 72, 73, and 7 Series products. Inlet and outlet ports are not threaded. High-flow, spring return 3-port/2-position, normally closed solenoid operated poppet valve. Combination lockout and quick exhaust valve. Equipped with a manually operated lockout slide that can be locked only in the closed position with a customer supplied padlock. Slide handle colored yellow for easy identification as a lockout valve. Standard internal pilot supply requires a main valve inlet pressure of 3 to 15 psig, although momentary drops below 3 psig are allowed by a check valve in the internal pilot passage. Optional voltages available. Short stroke, positive sealing, cushioned poppets for long service life. P7 Directional Control Valves 3-Port/2-position Solenoid Operated Valves with Lockout ISO Symbols Ordering Information Standard Models 3-Port/2-Position Normally Closed Model Numbers - Modular installation; 12V/Hz-11V5Hz, 7.5 watt solenoid coil; internal pilot supply; manual nonlocking override; cable grip electrical connector. Installation Weight 3-Port/2-Position Type lbs.kg Normally Closed Modular 2.3(.92) P7C-NAD-PJA Operation 3-Port/2-Position Normally Closed B (IN) A (OUT) B (IN) A (OUT) Options - Select the desired valve from the preceding order table, then change the model number as shown in the following diagram to obtain the desired option. Also see Product Numbering Chart on page 87 for additional options. Standard 7.5 Watt Coils L = 2 VAC K = 2 VAC Q = 12 VDC P = 2 VDC P7C-NAD-P A Service Kit Seal and gasket kit: 537- Moisture resistant connector seal: Coil retaining clip: Solenoid exhaust port diffuser: 53-1 Inlet Blocked Pressure to Port A * For valves with threaded ports, see NA-17. Littleton, CO USA Phone Fax /98

65 P7 Solenoid Operated Directional Control Valves Dimensions in inches (mm). Technical Data Fluids: Filtered and lubricated compressed air. Main valve inlet pressure range: 3 to 15 psig (2.1 to 1.3 bar) Operating temperature*: -2 to 12 F (-29 to 9 C). * Air supply must be dry enough to avoid ice formation at temperatures below 35 F (2 C). Average flow factor (C v ): In-Out Ports: 2. Out-Exhaust Ports: 5.3 Response times (elapsed time from solenoid energized to an increase in the main valve pressure): 11 ms at 9 psig Maximum diameter of customer supplied padlock shackle: 5/1" (8mm) Exhaust port: 1/2-1 PTF Solenoid Operator Electrical Specifications Voltage and power requirements: Voltage Wattage 2V/Hz/5Hz V/Hz-11V/5Hz 7.5 2V/Hz-22V/5Hz VDC 7.5 2VDC 7.5 Duty: Continuous at 9% to 15% of rated voltage. Coil Type: Molded with three pin plug-in connector. Enclosure Classification: NEMA 1, NEMA and IP 5. Connector Plug: Cable grip for cables 1/" to 5/1" ( to 8 mm) in diameter. Electrical connectors conform to Industry Standard Form B for Three-Pin Electrical Plug Connectors, 11 mm spacing. Override: Manual, nonlocking Materials Body: Zinc Pistons, Poppets: Aluminum Elastomers: Nitrile Operator Housing: PPS Plastic Operator Base: Aluminum Plunger & Spring: Stainless Steel 3-Port/2-Position Lock Out Valves.85 (17) 1. (3) 2.99 (7).57 (15) 1.75 () 2.28 () 1.97 (5) Rad (8) 1/98 Littleton, CO USA Phone Fax

66 EXCELON design allows in-line or modular installation with other 72, 73, and 7 Series products. Inlet and outlet ports are not threaded. Controls rate of downstream air pressure buildup at system start up. Cylinders and other air operated devices are eased into normal starting positions, reducing the possibility of equipment damage and hazard to user. Application of downstream pressure can be delayed for as long as 5 seconds, depending on the setting of the adjustable needle valve and downstream air volume. Smooth start valves must be installed downstream of a directional control valve such as a Norgren Poppet or Lockout Valve on the preceding pages. Short stroke, cushioned poppets for long service life. P7 Smooth Start Valves 2-port/2-position Normally Closed Poppet Valves ISO Symbol Ordering Information Standard Models Installation Weight Type lbs. kg Model Number Modular 1.17 (.53) P7E-NNN-NNN Operation See Product Numbering Chart on page 87 for additional options. Service Kit Seal and gasket kit: Normally Closed A (IN) B (OUT) A (IN) B (OUT) * For valves with threaded ports, see NCA-12. Restricted Air Flow to Port B Unrestricted Air Flow to Port B Littleton, CO USA Phone Fax /98

67 P7 Smooth Start Valves Dimensions in inches (mm) Technical Data Fluids: Filtered and lubricated compressed air. Inlet Pressure Range: 3 to 25 psig (2.1 to 17.2 bar). Operating temperature*: -2 to 13 F (-29 to 5 C). * Air supply must be dry enough to avoid ice formation at temperatures below 35 F (2 C). Average Flow Factor (C v ):. Materials Body: Zinc Pistons, Poppets: Aluminum Elastomers: Nitrile 2-Port/2-Position Smooth Start Valves 2.28 () 3.75 (95) 3. (91) 1. (37) 3.15 (8) 1/98 Littleton, CO USA Phone Fax

68 EXCELON design allows in-line or modular installation with other 72, 73, and 7 Series products. High-flow, 3-port/2-position, spring return, normally closed valve Controls rate of downstream air pressure buildup at system start up Available with air or solenoid operator Cylinders and other air operated devices are eased into normal starting positions, reducing the possibility of equipment damage and hazards to the user. High exhaust flow of downstream air when electrical signal or pilot air is removed. P72F Smooth Start/Exhaust Valve 1/'', and 3/8'' Port Sizes Ordering Information Standard Models ISO Symbols Model Numbers - PTF thread, solenoid operated valves include a non-locking manual override, 11/12 VAC coil, and a cable grip connector. Port Solenoid Operated Weight Air Operated Weight Size Model lbs. (kg) Model lbs. (kg) 1/ PTF P72F-2AC-PAA 2. (.91) P72F-2AA-NNN 1.93 (.88) 3/8 PTF P72F-3AC-PAA 1.98 (.9) P72F-3AA-NNN 1.91 (.87) Solenoid Operated Air Operated See Product Numbering Chart on page 88 for additional options. Optional Threads B ISO Rc taper G ISO G parallel Service Kits All models P72F - - Optional Solenoid Operator Electrical Connector B Cable grip with indicator lights (Use only with A and F coils) C 1/2 NPT conduit N No electrical connector Optional Solenoid Coil Voltage & Power Requirement D VDC, 2. watts E 12 VDC, 2. watts F 2 VDC, 2. watts H 11 VDC, 3. watts C 2 VAC, 2.5 Va K 22/2 VAC, 8 VA, 5/ Hz Y No coil, with base for 2.W Z No coil, with base for 2.W, 3., and 2.5 VA coils N No solenoid operator Normally Closed B (IN) A (IN) Exhaust B (OUT) A (OUT) Optional Solenoid Operator Override S...Locking, screwdriver slot N...No solenoid operator 8 Littleton, CO USA Phone Fax /98

69 P72F Smooth Start/Exhaust Valve Technical Data Fluid: Filtered and lubricated compressed air Main valve inlet pressure range: With solenoid operator: to 15 psig (3 to 1 bar) With air operator: to 25 psig (3 to 17 bar) Air operator pilot supply inlet pressure range: Equal to or greater than main valve inlet pressure, but not less than psig (3 bar) and not greater than 25 psig (17 bar). Operating temperature*: With solenoid operator: to +12 F (-18 to +5 C) With air operator: to +15 F (-18 to +5 C) * Air supply must be dry enough to avoid ice formation at temperatures below +35 F (2 C). Maximum flow with 9 psig (.3 bar) inlet pressure and pressure drop of 7.25 psig (.5 bar): 5 scfm (21 dm 3 /s) Average flow factor (Cv): In-out ports: 1. Out-exhaust ports: 1.7 Snap pressure: Full flow when downstream pressure reaches 5 to 8% of inlet pressure Charge time for.53 gallon (2 litre) downstream volume at 9 psig (.3 bar) inlet pressure:.8 to 7 seconds depending on setting of flow adjustment Solenoid operator specifications: DC Voltage and Power AC Voltage and Power VDC, 2W 2 VAC, 2.5 VA 12 VDC, 2W 11/12 VAC, 2.5 VA 2 VDC 2W 22/2 VAC, 8 VA 11 VDC, 3.W Duty: Continuous at 9% to 11% of rated voltage. Coil Type: Molded with three pin plug-in connector. Enclosure Classification: NEMA 1, NEMA and IP 5. Dimensions Inches (mm).95 (2) Solenoid Operated Valve 2.5 (5) 1.89 (8).95 (2) Air Operated Valve 2.5 (5) 1.89 (8) 1-32 pilot port with PTF main ports. M5 pilot port with ISO G and ISO Rc main ports. Connector Plug: Cable grip for cables 1/" to 5/1" ( to 8mm) diameter. Electrical connectors conform to Industry Standard Form B for Three-Pin Electrical Plug Connectors, 11 mm spacing. Solenoid Manual Override: Locking or nonlocking Materials Body: Zinc alloy Operator adapter (top) plate: Aluminum Elastomers: Nitrile Filter discs: Sintered plastic Operator housing: PPS plastic Internal components: Brass, steel NOTE Turn on inlet air to the valve before applying pilot signal to air or solenoid operator. PRESSURE DROP Performance Characteristics Port Size: 1/'' bar g psig Inlet Pressure psig bar g scfm dm 3 /s AIR FLOW MAXIMUM CHARGE TIME.33 (11).1 (15).77 (51) 3.58 (91) OUTLET PRESSURE bar g psig Inlet Pressure psig bar g SNAP POINT.53 gal (2 liter) downstream volume / PTF exhaust port with PTF main ports. ISO Rc 1/ exhaust port with ISO G and ISO Rc main ports. 1/ PTF exhaust port with PTF main ports. ISO Rc 1/ exhaust port with ISO G and ISO Rc main ports CHARGE TIME - SECONDS 1/98 Littleton, CO USA Phone Fax

70 P7F Smooth Start/Exhaust Valve 3/8'', 1/2'', and 3/'' Port Sizes EXCELON design allows in-line or modular installation with other 72, 73, and 7 Series products. High-flow, 3-port/2-position, spring return, normally closed valve Available with air or solenoid operator Controls rate of downstream air pressure buildup at system start up Adjustable rate of downstream pressure buildup Cylinders and other air operated devices are eased into normal starting positions, reducing the possibility of equipment damage and hazards to the user. High exhaust flow of downstream air when electrical signal or pilot air is removed. Optional manual operated lockout slide exhausts downstream air and shuts off pilot air when closed. Can be locked in closed position with a customer supplied padlock. Ordering Information ISO Symbols Model Numbers - Include PTF threads and an operator adapter plate without lockout slide. Solenoid operated valves include a non-locking manual override, 11/12 VAC coil, and a cable grip connector. Port Solenoid Operated Weight Air Operated Weight Size Model lbs. (kg) Model lbs. (kg) 3/8 PTF P7F-3AC-PAA 2.38 (1.8) P7F-3AA-NNN 2.31 (1.5) 1/2 PTF P7F-AC-PAA 2.31 (1.5) P7F-AA-NNN 2.25 (1.2) 3/ PTF P7F-AC-PAA 3.11 (1.1) P7F-AA-NNN 2.98 (1.35) Solenoid Operated Air Operated See Product Numbering Chart on page 88 for additional options. P7F - - Optional Solenoid Operator Electrical Connector B Cable grip with indicator lights (Use only with A and F coils) C 1/2 NPT conduit Optional Threads N No electrical connector A PTF threads, yellow slide B ISO Rc taper thread, red slide G ISO G parallel thread, red slide Optional Solenoid Coil Voltage & Power Requirement D VDC, 2. watts Operator Adapter Plate E 12 VDC, 2. watts A Air pilot F 2 VDC, 2. watts B Air pilot with lockout slide H 11 VDC, 3. watts C Solenoid pilot C 2 VAC, 2.5 Va D Solenoid pilot with lockout slide K 22/2 VAC, 8 VA, 5/ Hz Y No coil, with base for 2.W Z No coil, with base for 2.W, 3., and 2.5 VA coils Service Kits N No solenoid operator All models Optional Solenoid Operator Override S Locking, screwdriver slot* N No solenoid operator Normally Closed B (IN) A (IN) Exhaust B (OUT) A (OUT) * The locking override is not available with the D Operator Adapter Plate. 7 Littleton, CO USA Phone Fax /98