POWER PRODUCT Disconnect Switches Contents

Transcription

1 4 POWER PRODUCT Disconnect es Contents Compact Non-Fusible es 4-2 Rotary and Toggle Selection 4-4 Dimensions and Wire Ranges 4-5 Type VBII (0-A) Features and Ordering Information 4-6 and Handle Selection 4-7 Accessories Dimensions and Lug Wire Ranges 4-10 Type MCS (0-0A) es, Fuse, and No Fuse KitSelection 4-11 Handle Operators and Accessories Type CFS Compact Fusible es Features and Ordering Information 4-16 and HandleSelection 4-17 Accessories & -800 Handle Selection 4-18 Dimensions and Technical Characteristics 4-19 Type HCP board Units Selection/Accessories 4- Dimensions DISCONNECT Base Mount VBFS61 Panelboard Unit

2 4 DISCONNECT Disconnect es Compact Non-Fusible Rotary and Toggle Features b 16 2 Ampere, to hp, 480V & V b Rotary and Toggle actuation models b LBR Type switches are padlockable in the OFF position and are UL & cul listed under File No. E as manual motor controllers per UL Standard UL8 b LD2 Type switches are padlockable in the OFF position and are UL listed under File No. E47705 per UL8 and are CSA certified under File No. 576 b Base, DIN-rail and door mounting b Multiple conductor, distribution terminal type rating LBR & LBT Type (40A -A only) b IEC rated, CE marked b Listed and marked suitable as motor disconnect per NEC Section Application Siemens Load Break es are listed as manual motor controllers and are suitable as motor disconnects. They are load break rated and act as enclosure disconnects when short circuit protection is provided upstream of the switch. If upstream over current protection is not provided, use a Siemens fusible Type VBII, CFS or MCS Disconnect. Ordering Information Door Mounted es (Rotary Type Only) Order either complete LD2 assemblies or individual LBR components as follows: Complete Assemblies include switch, handle, and shaft. Certain 25 and 2A assemblies are also available with factory installed neutral blocks and/or aux. contacts. These accessories can also be ordered as field installed kits. Individual Components are ordered as follows: 25A LBR + LBRH or 4 handle. 40 A LBR switch + LBRH or 4 handle + LBRD1. Notes: (LBR Type switches only) 1. Aux contacts are available as field installed kits on 25A units only. 2. Lugs on 25A units face to the rear and lugs on 40 A units face toward the front. Type LBR Rotary es LD2254-0TK51 Base/DIN Rail Mounted es (Rotary or Toggle Type) Order individual components as follows: Toggle Order the LBT switch required and a toggle switch cover plate if needed. Rotary, Base Mounted with Door Mounted Handle Order LBR switch + door mounted handle + shaft + any accessories. Rotary, Base Mounted with Direct Mounted Handle Order LBR switch + direct mounted handle. Door Mounted Complete Assemblies Operator, Shaft, & ) V AC Max. b Type LBT Toggle es Selection Short Circuit Withstand Ratings Note: LD2 switches are also rated 5kA at V AC Max. when protected by a RV motor starter with a FLA rating equal to or less than the switch ampere rating. Shaft Mounted 4 Hole Mounted AC Horsepower Ratings Ampere 1V 240V 480V V c c of Poles Rating 1Ø 1Ø Ø Ø Ø LD0-1TP5 a /2 10 LD24-0TK LD24-1TP LD24-1TL LD24-2EP LD2254-0TK LD2254-1TL LD2555-0TK LD210-0TK LD210-1TP LD210-1TL LD210-2EP LD2-0TK LD2-1TL LD24-0TK LD2704-0TK LD2804-0TK a + N + N a / N Rating & Type Max. Line Side Fuse Rating 5kA with Line Side Class H, K, or RK5 Fuses 25 & 2A LD2 80A Max. at V AC Max. 6A LD2 175A Max. at V AC Max. 10kA with Line Side Class H, K, or RK5 Fusesd d 25A LBR 0A Max. at 480V AC Max. 40A, 4P A Max. at 480V AC Max. LBR & LBT 40 & A, P A Max. at 480V AC Max. LBR & LBT 80 & A 0A Max. at 480V AC Max. LBR & LBT 18kA with Line Side Class J, T, or CC Fuses 40 A, P LBR & LBT A Max. at 480V AC Max a Includes auxiliary contacts (1 NO and 1 NC). b Handles are IP65 rated and are also CSA certified for Type 1, 4X and 12 applications. c Add 51 for a black handle or 5 for a red & yellow handle to the end of the catalog number. d -2A LD2 switches are rated 10kA when protected by 0A Max. Class RK5 fuses. 4-2 Siemens Canada Limited Power Product

3 Disconnect es Compact Non-Fusible Rotary and Toggle LD Type Base Mounted Complete Assemblies (Operator, Shaft, & ) V AC Max. b Selection Handle Mounting Shaft (center hole) LD2144-0TK5 LD2144-1TL5 LD2244-0TK5 LD2244-1TL5 LD2545-0TK5 4 Hole (no defeat) LD1-0TK5 LD211-0TK5 LD211-1TL5 LD221-0TK5 LD221-1TL5 LD2514-0TK5 4 Hole (with defeat) LD17-0TK1 LD17-1TL1 LD2217-0TK1 LD2217-1TL1 LD2517-0TK1 LD2517-1TL1 a Handles and line side terminal covers are supplied as standard with LD2 switches. b Add suffix 1 for a black or for a red & yellow handle to the catalog number (except LD2244-1TL5 & LD221-1TL5). Handles are IP65 rated and are also CSA certified for Type 1, 4X and 12 applications. of Poles + N + N + N + N Ampere Rating AC Horsepower Ratings 1V 240V 480V V 1Ø 1Ø Ø Ø Ø / LD2714-0TK LD2814-0TK LD218-0TK LD2418-0TK Accessories for Front Mounted LD2 es Description es used with LD90-5B c LD90-5BF c LD92-2B LD92-2BA LD9280-2B LD92-0B LD92-0BA LD9280-0B LD9224-1B a LD9284-1B a LD9224-B a LD9284-B a LD9224-1D a LD9284-1D a LD9224-D a LD9284-D a LD9221-2A a LD9221-0A a LD9251-0A a 1 NO, 1 NC Aux. Contact 1 NO, 1 NC Aux. with Gold Plated Contacts Neutral/Ground Terminal Neutral/Ground Terminal Neutral/Ground Terminal 4th Pole (leading ON, lagging OFF) 4th Pole (leading ON, lagging OFF) 4th Pole (leading ON, lagging OFF) Black Handle (4 hole mtg.) Black Handle (4 hole mtg.) Red/Yellow Handle (4 hole mtg.) Red/Yellow Handle (4 hole mtg.) Black Handle (shaft mtg.) d Black Handle (shaft mtg.) d Red/Yellow Handle (shaft mtg.) d Red/Yellow Handle (shaft mtg.) d Terminal Cover 1P (Pack of 4) Terminal Cover P (Pack of 4) Terminal Cover P (Pack of 4) Accessories for Base Mounted LD2 es LD90-5C c LD90-5CF c LD92-2C LD92-2CA LD9280-2C LD9240-2C LD92-0C LD92-0CA LD9280-0C LD9240-0C LD9224-1B a LD9284-1B a LD9224-B a LD9284-B a LD9224-1D a LD9284-1D a LD9224-D a LD9284-D a LD9221-2A a LD9221-0A a LD9251-0A a 1 NO, 1 NC Aux. Contact 1 NO, 1 NC Aux. with Gold Plated Contacts Neutral/Ground Terminal Neutral/Ground Terminal Neutral/Ground Terminal Neutral/Ground Terminal 4th Pole (leading ON, lagging OFF) 4th Pole (leading ON, lagging OFF) 4th Pole (leading ON, lagging OFF) 4th Pole (leading ON, lagging OFF) Black Handle (4 hole mtg. no defeat) Black Handle (4 hole mtg. no defeat) Red/Yellow Handle (4 hole mtg. no defeat) Red/Yellow Handle (4 hole mtg. no defeat) Black Handle (shaft mtg.) Black Handle (shaft mtg.) Red/Yellow Handle (shaft mtg.) Red/Yellow Handle (shaft mtg.) Terminal Cover 1P (Pack of 4) Terminal Cover P (Pack of 4) Terminal Cover P (Pack of 4) A A 25 & 2A 6A & 125A 25 & 2A 6A & 125A 25 & 2A 6-125A 25 & 2A 6-125A 25 & 2A 6-125A 25 & 2A 6-125A 25 & 2A 25 & 2A 6A 25-2A 25-2A 25 & 2A 6A & 125A 1 & 2A 25 & 2A 6A & 125A 1 & 2A 25 & 2A 6-125A 25 & 2A 6-125A 25 & 2A 6-125A 25 & 2A 6-125A 25 & 2A 25 & 2A 6A c Aux. contacts break about 0 Ms before and make about Ms after main switch contacts. Ratings 10A at 1V AC 6A at 240V AC 1.4A at 480V AC Base Mount LD2217-0TK1 LD92-2C LD9251-0A Note: LD2 shaft lengths allow the following maximum enclosure depths from the switch mounting surface to the outside of the cover: 16-2A,.25" 6-125A,.75" 1 & 2A, 2.70" d Can be used as replacement handles on enclosed LD2 switches. e Base mounted switches with direct mount handles are also available (LD-0TK1 _ b rated 1A and LD240-0TK1_ b rated 2). 4 DISCONNECT Siemens Canada Limited Power Product 4-

4 Disconnect es Compact Non-Fusible Rotary and Toggle Individual Components and Assemblies Recommended for Basemount. For Door mounting only, use LBRD1. Rotary and Toggle es LBR040 g LBR0 g LBR080 g LBR g LBR4040 LBT040 LBT0 LBT080 LBT LBT4040 Type Rotary Rotary Rotary Rotary Rotary Toggle Toggle Toggle Toggle Toggle No of Poles 4 4 Ampere Rating Max AC Volt AC Horsepower Ratings 1V 240V 480V V 1Ø 1Ø Ø Ø Ø Standard and Heavy Duty Rotary Door Handles LBRH LBRH6 LBRH4 CFSH10B12 Selection 4 DISCONNECT LBR Type Handles Standard Duty LBRH2 b LBRH b LBRH4 b LBRH9 b LBRH10 b LBRH5 LBRH6 LBRH7 LBRH8 Heavy Duty CFSH10B12 CFSH10R12 Used on Rotary es NEMA Type Mounting Marking Colour All All All All (Pistol Grip Type) All (Pistol Grip Type) 25 Amps -Pole, 40- Amps -Pole, 80- Amps 4-Pole, 40- Amps All All 1 1, R, 12, 4X 1, R, 12, 4X 1, R, 12, 4X 1, R, 12, 4X , R, 12 1, R, 12 Door Door Door Door Door Direct Mount Direct Mount Direct Mount Direct Mount Door Door ON/OFF O/I, ON/OFF O/I, ON/OFF O/I, ON/OFF O/I, ON/OFF O/I O/I O/I O/I O/I, ON/OFF O/I, ON/OFF Black Black Red/Yel Black Red/Yel Black Black Black Black Black Red/Yel Cover Interlock Supplied No a a Padlockable No LBR Type Rotary Shafts Length - In. (mm) For Standard Duty Handles LBRS040 LBRS0 LBRS055 LBRS080 LBRS1 LBRS180 LBRS05 For Heavy Duty Handles CFSSH CFSS5400H Auxiliary Kits LBRA1 cd LBRA2 cd Used on Rotary es LBR040, LBR0 LBR080, LBR 1.57 (40) 1.97 () 2.17 (55). (80) 4.72 (1) 7.09 (180) (05) LBR Type Toggle Cover Plate LBTCP1 LBTCP2 LBTCP 7.9 (0).7 (400) Contact Arrangement 1 NO/1 NC with common point 1 NO/1 NC with common point Used on Toggle es LBT040, LBT0 LBT080,LBT LBT4040 Rotary Shafts LBRS1 LBRS080 LBRS040 LBR Type Rotary Door Mounting Kit (For use with LBRH & LBRH4 only) Used on Rotary es LBRD1 h 40- Amps LBR/LBT Neutral Kit e HF6CX Used with Catalog All LBR Type Handles LBRH6 Rotary and Toggle es LBT080 LBT0 a No cover interlock defeat mechanism provided. To eliminate cover interlock, order additional catalog number LBRDC1. b LBRH2 is IP54 rated. All others are IP65. c Ratings.1A resistive at 2V AC max..5a at 125V DC.25A at 2V DC.5 HP at 2V AC max. d Auxiliary switch contacts break about 0 Ms before and make about Ms after main switch contacts. e Lug wire ranges: HF6CX (1) #14-2 AWG /75 C Cu only f Only door mountable and for use with LBRH & 4 handles only. g For door mounting of 40 A LBR switches use door mounting kit LBRD1 & LBRH or 4 handle. LBRD1 does not require shaft. 4-4 Siemens Canada Limited Power Product

5 Disconnect es Compact Non-Fusible Rotary and Toggle Dimension Drawings and Wire Ranges Selection Dimension J Minimum Depth a Dimension J LBR 40-A.5 (85) LD2 25 & 2A Front Shaft Mounted.07 (78) LD2 6 Front Shaft Mounted.5 (85) LD2 16-2A Front 4-hole Mounted 2.1 (54) LD2 6A Front 4-hole Mounted 2.48 (6) LD2 & 125A Front 4-hole Mounted 2.56 (65) LD2 25 & 2A Base w/shaft Mtg. Handle 6.46 (164) LD2 6A Base w/shaft Mtg. Handle 6.77 (172) LD2 16-2A Base w/4-hole Mtg. Handle 5.59 (142) LD2 6A Base w/4-hole Mtg. Handle 5.99 (2) LD2-2A Base w/4-hole Mtg. Handle 6.07 (4) C a J E A F D LBR 025 Wire Ranges /75 C Cu only (1) #14 - #10 AWG Solid 25 Amps LBR (1) #14 - #8 AWG Stranded 40 & Amps LBR & LBT 80 & Amps LBR & LBT 16A, LD 25A, LD21 2A, LD22 6A, LD25, 125A, LD2 1, 2A, LD2 (1) #14 - #10 AWG Solid (1) #14 - #4 AWG Stranded UP to (4) #12 AWG Solid Up to () #12 AWG Stranded Up to (6) #14 AWG Stranded Up to (4) #14 AWG Stranded with (1) #10 AWG Stranded (1) #14 - #10 AWG Solid (1) #14 - #1 AWG Stranded (2) #6 AWG Stranded Up to () #8 AWG Stranded Up to (6) #10 AWG Stranded Up to (6) #12 AWG Solid (1) #18-10 AWG (1) #14-8 AWG (1) #14-8 AWG (1) #14-6 AWG (1) #12-1 AWG (1) #1-400 MCM a Drilling Pattern.125 (.2).877 (22.5).95 (24.1) Shaft Mounted LD2 Handle Cutout (4-hole pattern) 0.1 in. (8 mm) B LBR 40- Amps & LD2 16-2A.00 in. (76 mm) Minimum Depth F E C 0.1 in. (8 mm) B LBT Toggle 40- Amps A D 0.16 in. (4 mm) 0.16 in. (4 mm) G H G H 4 DISCONNECT Type Rotary Rotary Rotary Rotary Rotary Rotary Front Mtg. Rotary Front Mtg. Rotary Front Mtg. Rotary Front Mtg. Rotary Base Mtg. Rotary Base Mtg. Rotary Base Mtg. Rotary Base Mtg. Rotary Base Mtg. Toggle Toggle Toggle Toggle Toggle LBR040 LBR0 LBR080 LBR LBR4040 LD b LD21 & 2 b LD25? LD27 & 8 b LD b LD21 & 2 b LD25 b LD27 & 8 b LD2 & 4 LBT040 LBT0 LBT080 LBT LBT4040 a Depth from outside of cover to back of switch. Dimensions - Inches (mm) A B C D E F G H 2.00 (51) 2.00 (51) 2.09 (5) 2.09 (5) 2.42 (61) 1.89 (48) 1.81 (46) 2.6 () 2.40 (61) 1.89 (48) 1.81 (46) 2.6 () 2.80 (71) 4.41 (112) 2.00 (51) 2.00 (51) 2.09 (5) 2.09 (5) 2.42 (61) 2.72 (69) 2.72 (69).2 (84).2 (84) 2.72 (69) 1.97 () 2.17 (55) 2.52 (64).27 (8) 1.97 () 2.17 (55) 2.52 (64).27 (8) 5.8 (148) 2.72 (69) 2.72 (69).2 (84).2 (84) 2.72 (69) 2.72 (69) 2.72 (69) 2.92 (74) 2.92 (74) 2.72 (69) 1.97 () 1.97 () 2.2 (59) 2.40 (61) 2.29 (58) 2.29 (58) 2.68 (68) 2.76 (70) 4.10 (104) 2.75 (70) 2.75 (70) 2.90 (74) 2.90 (74) 2.75 (70) 1.78 (45) 1.78 (45) 1.97 () 1.97 () 2.28 (58) 1.78 (45) 1.78 (45) 1.97 () 1.97 () 2.28 (58) 2.16 (55) 2.16 (55) 2.29 (58) 2.29 (58) 2.16 (55) 2.16 (55) 2.16 (55) 2.29 (58) 2.29 (58) 2.16 (55) b Handle front plate dimensions: LD 16-2A2.64 inches square LD inches square 1.67 (42) 1.67 (42) 1.69 (42) 1.69 (42) 1.67 (42) 1.67 (42) 1.67 (42) 1.69 (42) 1.69 (42) 1.67 (42) 1. (8) 1. (8) 1.66 (42) 1.66 (42) 1. (8) 1. (8) 1. (8) 1.66 (42) 1.66 (42) 1. (8) 1.22 (1) 1.22 (1) 1.66 (42) 1.66 (42) 1.22 (1) 1.22 (1) 1.22 (1) 1.66 (42) 1.66 (42) 1.22 (1) Siemens Canada Limited Power Product 4-5

6 Disconnect es Type VBII (0-A) with Flange Mounted Operating Handle Features b 0-A, VAC and DC ratings b 240 & V AC switches are UL Recognized under file number E1212, Vol. and CSA certified under file number 4852 b Visible blade quick make and break switching action b Panel and Flange mounted assemblies facilite installation b Panel mounted switches are variable depth b Short circuit rating of 10,000 AIC with class H fuse, and of 0,000 AIC with class R or J fuses. b Flange mounted handles rated as Type 1, R & 12 or 4X are padlockable in the off position with up to () padlocks with 5/16 hasps b Meets UL98 requirements and suitable for both main and branch circuit applications b A complete line of aux contacts are available Features and Ordering Information b Load break and horsepower rated b Defeatable cover interlock standard with all handles b Meets NFPA79 requirements b Seismic qualified complies with the 10 California Building Code (CBC) and with the International Building Code (IBC) Compliance Level SDS = 1.85 g DISCONNECT 4 VBFS61, VBLK1 & VBH1 VBFS6F VBNFS65, VBLK4 & VBH2 Ordering Information 1. Determine the ratings required (amps, volts, HP, Fusible, NF), the mounting needed (Panel or Flange), and select the appropriate switch. 2. For panel mounted switches with a rigid operating shaft (0-A), order panel mounted switch, flange mounted operating handle & rigid linkage kit based on depth required.. For panel mounted switches with a Max-Flex operator, order panel mounted switch, Max-Flex Handle & Adapter Kit and drive cable. 4. Select accessories if required. 4-6 Siemens Canada Limited Power Product

7 Disconnect es Type VBII (0-A) with Flange Mounted Operating Handle Selection esfor Standard V Max AC or DC Applications Horsepower Rating, es and -Phasedd Amperage Rating Max. AC Voltage Rating 240 Volts AC 480 Volts AC Volts AC Std. Max. Std. Max. Std. Max. Volts DC (max)d Fusible Panel Mounted Variable Depth es - -Pole e VBFS21 VBFS22 VBFS61 VBFS62 VBFS6 VBFS64 VBFS65 VBFS a b c 0 c c i i Non-fusible Panel Mounted Variable Depth es - -Pole e VBNFS61 VBNFS62 VBNFS6 VBNFS64 VBNFS65 VBNFS66 Fusible Flange Mounted es - -Pole g VBFS21F VBFS22F VBFS61F VBFS62F VBFS6F VBFS64F c 0 c c i i a b c 0 c c 4 DISCONNECT Non-fusible Flange Mounted es -Pole g 0 0 VBNFS61F VBNFS62F VBNFS6F VBNFS64F c 0c c Note: Fusible switches include fuse provisions for Class H Fuses. The load base can be moved to pre-drilled holes for Class J Fuses on all V switches. If Class R Fuses are required, add a Class R Fuse Clip Kit. VBNFS61, VBHM1 & FHOEC06 Max-Flex TM Handle and Adapter Kit (Type 1, 12, R & 4X) Use with 0-0A panel mounted switches and cable kit. Plastic Handles VBHM1 Operating Handle Description 0-0A Type 1, R, 12 and 4X Metal Handles VBHM2 0-0A Type 1, R and 12 VBHM2X 0-0A Type 4X Cable Kit For use with 0-0A panel mounted switches and Max-Flex handle and adapter kit. FHOEC06 FHOEC048 Description 6" long drive cable 48" long drive cable a Rated 5 HP at 2V DC. b Rated 10 HP at 2V DC. c V DC & V DC horsepower rating shown requires (2) poles to be connected in series. d Std. - applies when non-time delay fuses are used. Max. - applies when time delay fuses are used. f Includes line base, load base, operating mechanism and line and load lugs. Order operating handle and linkage kits from tables on pages 4-7 or 4-8. g Please add letter "M" to the end of catalog number for metal handle. Siemens Canada Limited Power Product 4-7

8 4 DISCONNECT Disconnect es Type VBII (0-A) with Flange Mounted Operating Handle Flange Mounted Operating Handles For use with Panel Mounted es. Plastic handle is included with Flange Mounted es as standard. Plastic Handles Operating Handle Description VBH1 0-0A Type 1, R & 12 VBH14X Metal Handles 0-0A Type 4X VBH A Type 1, R & 12 VBH14 0-0A Type 4X VBH2 400A Type 1 & 12 VBH2R 400 & A Type 1, R & 12 VBH24X HR612 Class R Fuse Clip Kits These kits prevent the installation of Class H and K fuses (one kit required per switch). Class R Fuse Clip Kits HR21 HR612 HR62 HR6 HR64 HR656 Internal Door Latch Kits For use with enclosures with door mounted latching bar. Required when a flange mounted switch is mounted in a Hoffmann or Rittal enclosure provided with an AB cutout. DKR2 DKR 400 & A Type 4X Description 0A, 240V Kit (HD only) 0A, V Kit/A, 240V Kit A, V Kit A Kit 0A Kit 400A/A Kit Description 2 point (for use with enclosures less than 40" high) point (for use with enclosures 40" or larger in height) Rigid Linkage Kits For use with Panel Mounted es. Not required for Flange Mounted es. Ampere Rating HT6 Enclosure Depth Min Class T Fuse Adapter Kits -A fusible switches are field convertible to accept Class T fuses. 400-A switches are field convertible to accept Class T fuses by moving the load base to a pre-drilled T fuse position. Class T Fuse Adapter Kits Max. VBLK ? VBLK VBLK 400 & VBLK4 400 & HT2 HT6 HT24 HT64s Class J Fuse Provisions All 0-A, V fusible switches are field convertible to accept Class J fuses by moving the load base to a pre-drilled J fuse position. Window Kits (Type 1, 12, R and 4x) Allows viewing of visible blades and of indicating fuses through 0A. VBWK1 VBWK2 VBWK Description A, 240V Kit A, V Kit 0A, 240V Kit 0A, V Kit Description 0A Window Kit & A Window Kit 0-A Window Kit NEW Selection & Accessories Quick Connects They provide two point control power take-off capability and are normally used on two poles on the line side when it is required to have control power available when the switch is in the OFF position. They provide a mounting provision for standard ¼ quick connect terminal. Installed in the line or load side. 0A VBII switches have lugs to accept (2) wires per pole as standard so a 0A kit is not required. HCQ62 HCQ6 HCQ64 HN612 Neutral Kits Standard Neutral Kits can be field installed in 0-A switches. Neutral Kits Ampere Rating 0A V, A 240V 0% Neutral Kits CSA listed 0% Neutrals are available on & A switches. They are typically used with non-linear transformers or where increased neutral ampacity/lug capacity is required. 0% Neutral Kits Kit HNC612 A, V & A HNC62 Ampere Rating Description A 2 wire quick connect kit A 2 wire quick connect kit 0A 2 wire quick connect kit Kit Wire Range Line & Load Lugs (Cu/Al) & A HNC26 (2) #14-1/0 AWG s Built to order. Allow 6 8 weeks for delivery. Dimensions (min. & max.) from enclosure mounting pan to outside surface of enclosure handle mounting flange for 0A switches. One kit per pole required. 4-8 Siemens Canada Limited Power Product

9 Disconnect es Type VBII (0-A) with Flange Mounted Operating Handle Accessories Auxiliary Contacts The auxiliary contacts are available in 1 normally open and 1 normally closed or 2 normally open and 2 normally closed configurations. Siemens offers a PLC Auxiliary (0-0A) that has very low resistance for low voltage and current typical in PLC circuits. All auxiliary contacts make after and break before main switch contacts. HA16124 Ampere Rating Aux. Kit Ampere Rating With 1 NO & 1 NC Isolated Contacts Kit Horsepower Rating 125V AC 2V AC 28V DC 125V AC 2V AC 28V AC Max. Max. Max. Max. Max. Max. 0-0 HA /2 / HA /2 /4 With 2 NO & 2 NC Isolated Contacts 0-0 HA / HA /4 HA26124 Low Current PLC Type with 1 NO & 1 NC Gold Plated Contacts 0-0 HA /2 / HA /2 /4 Fuse Puller Kits Fuse Puller Kits are field installable in 0-A Type VBII Heavy Duty es (one kit required per -pole switch). 4 DISCONNECT HP61 HLC612 Ampere Rating 00 HP61 0 HP62s HP6s Fuse Puller Kit Copper Lug Kits All switches are CSA approved to accept field installed copper lug kits. Ampere Rating Copper Lug Cat. No. Description 0 HLC612 (9) Lugs/Kit #14-4 AWG Cu HLC6s (9) Lugs/Kit #14-1/0 AWG Cu 0 HLC64s (9) Lugs/Kit #6 AWG-00 Kcmil Cu 400 A HLC65678 (1) Lugs/Kit #1/0 AWG- Kcmil Cu Equipment Ground Kits Equipment Ground Lug Kits are available for all switches. Ampere Rating of Terminals Wire Range Per Terminal (Cu/AI) 0 0 HG #14-4 AWG 400 & HG656 4 #6 AWG-2 Kcmil HSK61 NEW Internal Shield Kits (for fusible switches) Kits provide a skirt that encloses the VBII switch and also a clear plastic inner door to prevent accidental contact with live parts. Test probe holes are provided and fuses can be replaced without removal of kit. Ampere Rating 0A Shield Kit HSK61 -A HSK62 0A HSK64 s Built to order. Allow 6 8 weeks for delivery. Siemens Canada Limited Power Product 4-9

10 Disconnect es Type VBII (0-A) with Flange Mounted Operating Handle Lugs 0 & A switches are suitable for use with or 75 C wire. A switches are suitable for use with 75 C rated wire. All switches are supplied with factory installed line and load lugs. Selection Wire Ranges (Line, Load and Standard Neutral) Ampere Rating Lug Wire Range 0 #14-2 AWG (Cu/Al) #14-2 AWG (Cu/Al) 4 #14-1/0 AWG (Cu/Al) 0 #6 AWG-00 Kcmil (Cu/Al) 400 (1) 1/0 AWG-7 Kcmil (Cu/Al) or (2) 1/0 AWG-2 Kcmil (Cu/Al) (2) 1/0 AWG-7 Kcmil (Cu/Al) or (4) 1/0 AWG-2 Kcmil (Cu/Al) DISCONNECT Approximate Dimensions Mounting bracket shown with handle installed is supplied with Flange Mounted es only. All Panel Mounted es have a L shaped mounting pan with a line base, load base (if fusible) and mechanism installed. Dimensions A B C a D (min) D (max) Fusible, Panel Mounted VBFS VBFS VBFS VBFS N/A VBFS VBFS VBFS VBFS Non-fusible, Panel Mounted VBNFS VBNFS VBNFS N/A VBNFS VBNFS VBNFS Fusible, Flange Mounted VBFS21F VBFS22F VBFS61F VBFS62F N/A VBFS6F VBFS64F Non-fusible, Flange Mounted VBNFS61F VBNFS62F VBNFS6F N/A VBNFS64F D A C a Dimension C for panel mounted switches indicates the minimum width from the left hand edge of the switch mounting pan to the right hand inside surface of the enclosure Siemens Canada Limited Power Product

11 Disconnect es Type MCS (0-0A) es, Fuse and No Fuse Kits Features b 0,, and 0 Ampere es b UL Recognized (file # E1212 vol. 1 & 2) and CSA Certified under file #84625 b Simple Mounting with an integral switch and over center mechanism b Horsepower & load break rated b Compact Size b Visible Blade Contacts b Rugged Construction with a short circuit current rating of 10,000 amps with Class H or 0,000 amps at V maximum AC, when fused with Class R or Class J fuses Selection b Available with three operator handle options, allowing flexible placement of switch b Field Installable Auxiliary Contacts b Flexible Fuse Class Configurations b Flange mounted handles meet NFPA79 requirements Type MCS Disconnect with Max-Flex handle operator Ordering Information 1. Select the basic switch size you need (0,, or 0 ampere). 2. Check the switch selected against the maximum horsepower rating required for our application. L or R suffix on switch catalog numbers denotes left or right-handed mechanism drive. Basic es Ampere Rating Max. Voltage Rating Right Hand Left Hand Type MCS Disconnect with fixed-depth, flange-mounted handle. Choose either fuse or no fuse kit from chart below. Information 4. Check Minimum Dimensions on page 5-12 for installation space requirements. Standard Fuse Max. Horespower Rating, Phase d Type MCS Disconnect with rotary handle 5. Select from the list of handle operators, the type which best suits your application. Handle operators can be selected from the next page. 240 Volts AC 480 Volts AC Volts AC Time Delay Fuse Standard Fuse Time Delay Fuse Standard Fuse Time Delay Fuse 0 MCSR MCSL 5 MCS6R MCS6L 0 10 MCS610R MCS610Ls MCS6R MCS6Ls Volts (max) d 4 DISCONNECT Fuse And No Fuse Kits (Includes load base plus line and load fuse clips) a No Fuse Kits For Class H For Class J For Class R Basic Standard Cu Only b Ampere Kit Rating Description a a a No Fuse TMK6 MCSR 0A, 2V FCKs FCRK 10 or 0A, V FCK6 FCJK FCRK6 MCSL A, 2V FCK6 FCRK6 A, V FCK6 FCJK6 FCRK6 No Fuse TMK6 MCS6R A, 2V FCK6 FCRK6 1 or A, V FCK6 FCJK6 FCRK6 MCS6L A, 2V OFCK661s OFCK661s c A, V OFCK661s OFCK661s c 0 MCS610R or MCS610L MCS6R or MCS6L No Fuse A, 2V A, V 0A, 2V TMK610 s Built to order. Allow 6 8 weeks for delivery. a For copper only connectors, order as follows: Fusibleorder standard switch, standard fuse kit and copper only no fuse kit. TMK610C FCK610 FCK610 OFCK6 Non-Fusibleorder standard switch and copper only no fuse kit. b Includes both line and load lugs. FCK610 FCK610 OFCK6 c c c Lug Wire Size #14 to #4 AWG Cu/AI #14 to #4 AWG Cu/AI #14 to #2/0 AWG Cu/AI 0A, V OFCK6 OFCK6 c No Fuse TMK6 TMK6Cs #6 to 0A, 2V FCK6 FCK6 c 00 kcmil 0A, V FCK6 FCK6 c Cu/AI c For Class R fuses order Class H kit from this table and the Class R conversion kit from the next page. d HP ratings for time delay fuses and for 2V DC also apply to Non-fusible switches. Siemens Canada Limited Power Product 4-11

12 4 DISCONNECT Disconnect es Type MCS (0-0A) Auxiliary Kits Contact Arrangement 1 NO/1 NC 2 NO/2 NC MCSR MCSAKR16 MCSAKR26 MCSL MCSAKL16 MCSAKL26s MCS6R MCSAKR16 MCSAKR26 MCS6L MCSAKL16 MCSAKL26s MCS610R MCSAK116 MCSAK216 MCS610L MCSAK116 MCSAK216 MCS6R MCSAK126 MCSAK226 MCS6L MCSAK126 MCSAK226 Handle Operators Fixed Depth, Flange Mounted, Types 1,, R, 12 af Class R Fuse Conversion Kits Fuse Clip Rating A, V SSRK 0A, V SSRK4 Fuse Ejector Kits MCS610 MCS6 Complete Handle Mechanism Handle Only Operator Only MCSR FDFS06R FDH10 FDS06R MCSL FDFS06L FDH10 FDS06L MCS6R FDFS06R FDH10 FDS06R MCS6L FDFS06L FDH10 FDS06L MCS610R FDFS06R FDH10 FDS06R MCS610L FDFS06L FDH10 FDS06L MCS6R FDFSR FDH FDSR MCS6L FDFSL FDH FDSL Variable Depth, Flange Mounted Max-Flex, Types 1,, R, 12 b Fuse Ejector Kit FEs FE0s Complete Handle Mechanism Handle Only Operator Only Cable Only c MCSR FHOS06R FHOHS FHOS06R FHOEC06 MCSL FHOS06L FHOHS FHOS06L FHOEC06 MCS6R FHOS06R FHOHS FHOS06R FHOEC06 MCS6L FHOS06L FHOHS FHOS06L FHOEC06 MCS610R FHOS06R FHOHS FHOS06R FHOEC06 MCS610L FHOS06L FHOHS FHOS06L FHOEC06 MCS6R FHOS06R FHOHS FHOSR FHOJC06 MCS6L FHOS06L FHOHS FHOSL FHOJC06 Accessories Variable Depth Rotary, Through-The-Door-Mounted, Types 1, 12 de Variable Depth Shaft Only Variable Depth MCSR CRHOS06VD CRHOH RHOS06 RHOSVD MCS6R CRHOS06VD CRHOH RHOS06 RHOSVD MCS610R CRHOS06VD CRHOH RHOS06 RHOSVD MCS6R CRHOSVD RHOH RHOS RHOSVD MCS Disconnect Panel Space Requirements Panel Space Requirements Minimum Dimensions (inches*) Size "A" "B" "C" MCS MCS6 MCS610 MCS6 0A/240V 0A/V 0A/V A/240V A/V A/V A/240V A/V A/V 0A/240V 0A/V 0A/V Fuse Clases H, K, R H, K, R J H, K, R H, K, R J H, K, R H, K, R J H, K, R H, K, R J A Dimension is measured from each cross bail pin. B Dimension is measured from line side barrier to load side barrier. C Dimension is measured from line side terminal of switch to load side terminal of fuse load base. s Built to order. Allow 6 8 weeks for delivery. a For Type 4 and 4X applications, order handle only A - FDH104 0A - FDH4 b For Type 4 and 4X applications, order handle only FHOHS4 c Standard cable length is 6 inches. Alternate lengths are available as follows: Length Amps Cat. No. 48" 0 FHOEC048 " 0 FHOEC0 48" 0 FHOJC048 " 0 FHOJC0 d For Type 4 and 4X applications, order handle only Catalog RHOH4 e For Type and R applications, order handle only Catalog RHOH f Min. enclosure depth from mounting pan to handle mounting surfaces: 0-A 6.44 Inches 0A 10.9 Inches *For millimeters multiply inches by Siemens Canada Limited Power Product

13 Disconnect es Motor Control Disconnect Outline Drawing 0/A Mechanism Selection Dimensional Data for Fused Applications - Inches (mm) Basic Size A B Fuse Class 0A/240V 8.11 (6).6 (92) H, K, R MCS 0A/V (257) 5.6 (14) H, K, R 0A/V 8.48 (2) 4.00 (102) J A/240V 7.86 (0).8 (86) H, K, R MCS6 A/V 10.6 (26) 5.88 (149) H, K, R A/V 8.6 (212).88 (99) J a Overall Width Using Auxiliary Single Pole (182) Double Pole (194) b Auxiliary switch mounts on opposite side from mechanism. Auxiliary Detail 4 DISCONNECT Outline Drawing A Mechanism Dimensional Data for Fused Applications - Inches (mm) Basic Size A B C MCS610 Fuse Class A/240V (01) (290) 6.66 (169) H, K, R A/V 1.85 (52) 1.41 (41) 8.66 (2) H, K, R A/V 10. (296) (258) 5.41 (17) J a Overall Width Using Auxiliary Single Pole (192) Double Pole () b Auxiliary switch mounts on opposite side from mechanism. Siemens Canada Limited Power Product 4-1

14 Disconnect es Motor Control Disconnect Outline Drawing 0A Mechanism Dimensional Data for Fused Applications - Inches (mm) Basic Size A B Fuse Class 0A/240V (7) 6.00 (2) H, K, R MCS6 0A/V 17. (47) 8. (216) H, K, R 0A/V 1.2 (8) 4.62 (117) J Selection a Overall Width Using Auxiliary Single Pole (26) Double Pole (248) b Auxiliary switch mounts on opposite side from mechanism. 4 DISCONNECT Auxiliary Detail Rotary Handle Operator Dimensions - Inches (mm) A B C D CRHOH 1.18 (0) 2.6 ().00 (76) (4) RHOH 1.59 (40).18 (81). (89) (7) Dimensions - Inches (mm) : CRHOS06 CRHOS RHOS06 RHOS Enclosure Min (18) 6.17 (7) 4.75 (121) 5. (140) Depth (K) Max..7 (400) (414) 16.0 (419) (428) Shaft Length (L) K-2.77 (70) K-.42 (87) K-2.25 (57) K-2.90 (74) Dimensions - Inches (mm) A B C D MCSR, MCS6R 1.89 (48) 1. (8) 4.0 (102) 1.10 (28) MCS610R.00 (76) 1.81 (46) 4.7 (111) 1.17 (0) MCS6R 5.44 (18) 7.85 (199) 2.5 (64) 1.41 (6) MCSR, MCS6R, MCS610R MCS6R 4-14 Siemens Canada Limited Power Product

15 Disconnect es Motor Control Disconnect Fixed Depth Handle Operator Dimensions - Inches (mm) X1 X2 Y1 Y2 Z1 MCS, MCS6.52 (89) 1. (8) 0.00 (0) 1.89 (48) 6.44 (164) MCS (99) 1.81 (46) 0.1 ().00 (76) 6.44 (164) MCS (8) 7.86 (0) 0.8 (10) 5.44 (18) 10.9 (278) Selection 4 DISCONNECT Max Flex TM Variable Depth Handle Operator Dimensions - Inches (mm) A B C D E F MCS, MCS (51) 1.69 (4) 5.10 (10) 2.88 (7) 1. (8) 1.89 (48) MCS (51) 0.82 (21) 5.10 (10).21 (82) 1.81 (46).00 (76) MCS6 2. (64) (-25) 5. (140) 1.00 (25) 7.86 (0) 5.44 (18) Maximum E Dimension a Cable Enclosure Depth inches (mm) MCS, MCS6 FHOEC (406) 1.0 (0) 1.5 (4) 8.0 () MCS610 FHOEC (6) 26.0 (6) 26.0 (6) 2.0 (584) 21.0 (5) 18.0 (457) 17.0 (42) MCS6 FHOJC06.0 (81) 12.0 (05) 12.5 (18) 7.0 (178) FHOJC (65) 25.0 (65) 25.0 (65) 22.0 (559).0 (8) 17.0 (42) 16.0 (406) Enclosure Depth in. (mm) 6 Cable 48 Cable Fmin. Fmax. Fmin. Fmax. 8 () 7.0 (178) 14.5 (68) 16.1 (409) 2.9(7) 10 (254) 5.5 (140) 1.1 () 16.0 (406) 2.6(599) 12 (05) 5.0 (127) 12.0 (05).9 (404) 22.8(579) 16 (406) 4.0 (102) 9.4 (29) 14.7 (7) 22.0(559) 18 (457) 14.6 (71) 21.9 (556) (8) 1. (8) 19.9 (5) 24 (610) 12.0 (05) 16.9 (429) a Maximum E Dimension only if F max = 4.6 (117) Siemens Canada Limited Power Product 4-

16 Disconnect es Type CFS Compact Fusible es Features b 0-800A ratings b UL Listed under file #E1212 & CSA Certified under file # b Door mounted rotary handles with defeatable cover interlock b Meets UL/CSA requirements for both main and branch circuit applications b Compact size b ka with Class CC fuses or up to 0kA with Class J fuses b Load break and horsepower rated b Quick make and break operation b All handles are padlockable with up to () padlocks with 5/16 hasps in the OFF position Features and Ordering Information b number CFS61C5, CFS61J5 and CNFS61 can be DIN-rail mounted and can be either front or side operated with standard rotary handles. b All CFS part numbers ending in N can be either front or side operated with standard rotary handles. b Handles are available in Type 1, R, 4/4X & 12 ratings b NFPA 79 field installed kits are available b 0-400A, 0kA switches are provided with quick connect terminal provisions for voltage sensing or for 10A max. control circuits b Fusible switches, -pole V AC Max. 0-A & -800A switches are also rated 2V DC Max when poles are field connected in series. 4 DISCONNECT Shaft Handle Lugs/Accessories CFS6JN with (2) CFSAUX1NO CFSSHN CFSH10BL12N CFSL0 Ordering information 1. Select the panel mounted switch required based on Ampere, HP and AIC requirements. es with a right hand mechanism are standard, 0-A switches with a left hand mechanism are available. 2. Select handle based on environmental rating required.. Select operating shaft (0 or 400mm in length). For enclosure depths of 9.0 or less from panel mounting surface to inside of door use 0mm long shafts. For deeper enclosures use 400mm long shafts. 0A ka switches can be used in 10 deep enclosures (panel to inside of door) with 0mm shaft and CFSH5N handles. Note: Be sure to check shaft and handle compatibility with the switch selected by using information provided in the selection tables. 4. Line & load lugs are provided as standard on 0-A switches. Terminal kits are available for 0-800A switches if needed. 5. Auxiliary contact are available if needed as follows. A. 0A switch CFS61C5 and non-fusible 0A switch CNFS61 will accept up to (4) aux contacts B. 0A switch CFS61J5 will accept up to (2) aux contacts without an aux contact holder. If more than (2) aux contacts are required order aux contacts PLUS aux contact holder kit CFSAUXH1. All other switches will accept up to (4) aux contacts. 6. If non-fusible switch is required order a shorting bar for -A switches or catalog number CNFS61 for 0A A switches are designed to prevent inadvertent contact with live parts and shields are not required. 0 & 400A switches are not supplied with terminal shields. They are available as field installed kits for both line and load terminals A switches are supplied as standard with line shields and terminal shroud kits are available for the load side Siemens Canada Limited Power Product

17 Disconnect es Type CFS Compact Fusible es Fusible switches, -pole V AC Max. 0-A & -800A switches are also rated 2V DC Max when poles are field connected in series e ampere rating Fuse provisions provided Standard with right hand mounted mechanism 0 a 0 a 0 a 0 a CFS61C5 CFS61J5 CFS61JN CNFS61 hk Class CC Class J Class J None Max horsepower ratings 240V Ø AC 480V Ø AC V Ø AC 2V DC 5 c 5 c 5 c 5 c AC short circuit rating ka ka 0kA 65kA a CFS62JN1 Class J 0 10 c ka a a 0 b 400 b b CFS62JN CFS6JN CFS64JN d CFS65JN d CFS66J ij Class J c c 0kA 800 b CFS67L ij Class L kA Optional with left hand mounted mechanism d 0 a a a CFS61JLN CFS62JLN CFS6JLN Class J Operating shafts for 0-400A switches e CFSSN CFSS5400N CFSSHN CFSS5400HN CFSSHN CFSS10400HN Shaft length in. (mm) 7.9 (0).7 (400) 7.9 (0).7 (400) 7.9 (0).7 (400) & handle compatibility 75 5 c 10 c c 0kA 5mm x 5mm for use with CFS61C5, CFS61J5 &CNFS61 switches & with CFSH5 handles only 5mm x 5mm for use with all CFSH10 handles & with CFS61C5, CFS61J5 & CNFS61 switches only 10mm x 10mm for use with all CFSH10 handles & with all 0-400A switches except CFS61C5, CFS61J5 & CNFS61 and Handle Selection CFS61J5 CFSS5400N 4 DISCONNECT Compact rotary operating handles door mounted (for use with CFS61C5, CFS61J5 & CNFS61 switches only) f Colour Type Operating shaft compatibility CFSH5B12N CFSH5R12N CFSH5B4N CFSH5R4N Blue & Black Yellow & Red Blue & Black Yellow & Red 1, R & 12 1, R, 12 & 4/4X CFSSN or CFSS5400N Rotary operating handles - door mounted (for use with CFSSHN, CFSS5400HN, CFSSHN & CFSS10400HN) Colour Description Type 1, R & 12 g CFSH5B12N CFSH10B12N Blue & Black Heavy duty pistol grip (2.75 long for use CFSH10R12N Yellow & Red with 0A switches & CFS62JN1) CFSH10BL12N Blue & Black Heavy duty pistol grip CFSH10RL12N Yellow & Red (4.92 long for 0-400A switches) Type 1, R, 4/4X & 12 g CFSH10B4N Blue & Black Heavy duty pistol grip (2.75 long for use CFSH10R4N Yellow & Red with 0A switches & CFS62JN1) CFSH10BL4N Blue & Black Heavy duty pistol grip CFSH10RL4N Yellow & Red (4.92 long for 0-400A switches) a Line and load lugs included. b Line and load lugs are not included. Order from table on next page if required. c DC HP rating shown requires () poles to be connected in series. d CFS64JN & CFS65JN can be rotated 180º for left hand operation as standard. e Catalog numbers CFS61C5, CFS61J5 & CNFS61 accept 5mm x 5mm operating shafts. All other 0-400A switches accept 10mm x 10mm operating shafts. f Compact pistol grip design (2.75 long) with defeatable cover interlock. Cover can be opened when handle is padlocked in the OFF position. g Defeatable cover interlock provided. Cover cannot be opened when handle is padlocked in the OFF position. h Catalog number CNFS61 is a non-fusible switch. i 4 pole & 800A switches, CFS466J & CFS467L are also available. j CFS66J and CFS67L are rated 2 & V DC when (2) poles are connected in series. k CNFS61 is rated 65kA when protected by Class J or CC 0A max. fuses. Siemens Canada Limited Power Product 4-17

18 4 DISCONNECT Disconnect es Type CFS Compact Fusible es & 800A rotary operating handles - door mounted (8.27 long) g number Colour Type CFSH12BL12 CFSH12RL12 Blue & Black Yellow & Red 1, R & 12 1, R & 12 CFSH12BL4 CFSH12RL4 Blue & Black Yellow & Red 1, R, 12 & 4/4X 1, R, 12 & 4/4X & 800A operating shafts (cross section 12 x 12 mm) CFSS120H CFSS12400H Shaft length in. (mm) ().75 (400) Type CFS fusible switch accessories Terminals a CFSL0 CFSL400N CFSL400 Shorting Bars (no fuse kits) CFSSB CFSSB CFSSB0 CFSSB400 CFSSB680 Description Enclosure depth (switch mounting surface to door OD) in in. 0A lug kit (6 lugs per kit) (1)#6-/0 400A lug kit (6 lugs per kit) (1)#2-kcmil (for CFS65JN only) -800A lug kit (6 lugs per kit) (2)#2-kcmil A shorting bar kit ( links per kit) A shorting bar kit ( links per kit) 0A shorting bar kit ( links per kit) 400A shorting bar kit ( links per kit) & 800A shorting bar kit (1 link per kit) Auxiliary Contacts (NEMA ratings AC A DC N) CFSAUXH1 b CFSAUX1NO CFSAUX1NC CFS11AUX CFS22AUX Terminal Shrouds (line or load) Aux contact holder (CFS61J5, CFS61C5 & CNFS61) Aux contact 1 NO (0-800A Sws) Aux contact 1 NC (0-800A Sws) 1NO, 1NC aux contact kit (side mount for 0kA switches) 2NO, 2NC aux contact kit (side mount for 0kA switches) CFSTS0N h 0A shroud kit (line or load -pole kit) CFSTS400N h 400A shroud kit (line or load -pole kit for CFS65JN only) CFSTS680 f /800A -pole shroud kit CFSTS6804 f /800A 4-pole shroud kit 0A compact switch kits CFSPLK Shaft padlocking kit for 0A compact switch when door is open c CFSH5CDM Direct mount handle kit for CFS61C5 & CNFS61 CFSH5JDM Direct mount handle kit for CFS61J5 NFPA 79 kits (if auxiliary contacts are needed, see table on page 7) Kits provide an operating shaft suitable for use with all heavy duty handles (not for use with CFSH5 handles). Kits also provide an internal operating handle and an internal OFF padlocking provision. CFSNFPA1 d CFSNFPA2N e CFSNFPAN e For use with CFS61C5, CFS61J5 & CNFS61 For use with CFS61JN, CFS61CN, CFS62JN1, CFS62JN, CFS6JN & CFS64JN For use with CFS65JN only Selection and Accessories CFSL0 & 400 CFSAUX1NC CFSSB - CFSSB400 a Supplied as standard on 0-A switches b CFS61C5 and CNFS61 will accept (4) aux contacts without an aux contact holder. CFS61J5 will accept (2) aux contacts without an aux contact holder. c Supplied as standard on all but 0A, 65kA & ka compact switches. d 12.6 in. ( mm) long operating shaft included e 12.7 in. (2 mm) long operating shaft included f Line side terminal shrouds supplied with switch g Defeatable cover interlock included. Cover cannot be opened when the handle is padlocked in the OFF position. h Neither line or load terminal shrouds are supplied as standard with new style 0 & 400A switches Siemens Canada Limited Power Product

19 Disconnect es Type CFS Compact Fusible es Dimensions and Technical Characteristics UL & CSA technical characteristics and panel space requirements Amps Fuse Class AC short circuit rating Electrical endurance Mechanical endurance Panel space requirements - in. (mm) Height Width Depth a CFS61C5 0 CC ka (116).78 (96) 6.00 (2) CFS61J5 0 J ka (116) 4. (105) 6.00 (2) CFS61JN 0 J 0kA (16) 5.89 (0) 6.00 (2) CFS61JLN 0 J 0kA (16) 5.89 (0) 6.00 (2) CNFS61 0 None 65kA b (116).78 (96) 6.00 (2) CFS62JN1 J ka (16) 5.89 (0) 6.00 (2) CFS62JN J 0kA (186) 5.89 (0) 6.00 (2) CFS62JLN J 0kA (186) 5.89 (0) 6.00 (2) CFS6JN J 0kA (186) 5.89 (0) 6.00 (2) CFS6JLN J 0kA (186) 5.89 (0) 6.00 (2) CFS64JN 0 J 0kA (291) 7.72 (196) 6.00 (2) CFS65JN 400 J 0kA (90) (259) 8.00 () CFS66J J 0kA (00) 14. (64) 11 (280) CFS466J J 0kA (00) 18.0 (458) 11 (280) CFS67L 800 L 0kA (00) 14. (64) 11 (280) CFS467L 800 L 0kA (00) 18.0 (458) 11 (280) Wire ranges line & load lugs Amperage Rating Wire size (75º C) CFS61J5 0 (1)#14-10 CFS61C5 0 (1)#14-10 CNFS61 0 (1)#14-10 CFS61JN 0 (1)#14-6 CFS62JN1 (1)#14-6 CFS62JN (1)#12-1 CFS6JN (1)#12-1 CFS64JN 0 (1)#/0 CFS65JN 400 (1)MCM CFS66J (2) MCM CFS67L 800 (2) MCM Auxiliary contact capability when an NFPA79 kit is used NFPA79 kit Aux contacts that can be installed CNFS61 CFSNFPA1 (2) Total, CFSAUX1NO CFS61C5 or CFSAUX1NC CFS61J5 (1) CFSAUX1NO or (1) CFSAUX1NC CFS61JN CFSNFPA2N (2) Total, CFSAUX1NO or CFSAUX1NC c CFS62JN1 CFS62JN CFS6JN CFS64JN CFS65JN CFSNFPAN (2) Total, CFSAUX1NO or CFSAUX1NC c 4 DISCONNECT a Minimum dimensions from mounting surface to inside of cover. Dimensions shown can be decreased if aux contacts are not required. b CNFS61 is rated 65kA when protected by 0A max. Class J or CC fuses. c For additional auxiliary contacts use side mounted CFS11AUX or CFS22AUX. Siemens Canada Limited Power Product 4-19

20 Two Speed Starters Non-Combination Features b CSA certified under file #2456 and UL Listed under file #E6849 Vol 1, Sect. 8 b A ratings b Visible contacts b Field installable shunt trip and auxiliary switch accessory kits b Installs in existing Siemens switchboards and power panelboards b Suitable for use on systems with up to 0,000A available fault current, RMS symmetrical when equipped with Class J or Class L fuses b Group mounts with other 0A through A switches, and through 10 amp frame breakers b Allows 800A and 10A switches in standard 8" wide distribution sections in either main or branch configurations b " mounting height is the smallest 10A design in the industry, allowing up to 4 units in one vertical section b Field reversible horizontal mounting design for left or right hand cabling b Handle can be padlocked in the OFF position with up to three padlocks with 5/16" hasps. A cover padlocking provision is also supplied Selection 4 DISCONNECT -Pole, Horizontal Mount a Horsepower Rating Max. Max. Ampere AC Voltage Fuse Dimensions - Inches* 240V 480V V 2V Rating Rating b Class H W D Std Max Std Max Std Max DC HCP67HJ J HCP67HJ 1 J HCP27HT T HCP67H 1800 L HCP28HT T HCP68H 10 L Pole, Vertical Mount HCP67VJ J HCP67VJs 1 J HCP27VT T HCP67V 1800 L HCP28VT T HCP68V 10 L HCP67HJ J HCP67HJ J HCP67HJ J Accessories Terminal Connectors (one lug per kit) Ampere Rating Connector Wire Range 400 A TA2K0 (2) #1 AWG 0 kcmil (Cu or AI) 400 A TC2K0 (2) #1 AWG 0 kcmil (Cu only) A TAK0 () #1 AWG 0 kcmil (Cu or AI) A TCK () #1 AWG kcmil (Cu only) A TA4H0 (4) #2 AWG 0 kcmil (Cu or AI) A TAH7 () 0 7 kcmil (Cu or AI) Auxiliary Kits Contact Maximum Voltage Ampere Rating AC DC Shunt Trip Kit Control Voltage AC DC 1 HCPST1 240 HCPST240s 277 HCPST HCPST480s Mounting Contacts Catalog A Left Pole 1NO/1NC A01HCPL4s A Right Pole 1NO/1NC A01HCPR4 board Connection Strap Kit a Ampere Rating Catalog A F6162DSCAN T Fuse Adapter Kits (one per pole) Description TFAK A, 00V AC TFAK A, V AC TFAK82 10A, 00V AC HCP Replacement Handle Kit (For use on all HCP switches) SW Ampere Rating A HCPHK Compression Lug Adapter Kit The use of this kit provides for the mounting of up to four lugs per phase. Each kit accepts lugs with (2) /8" diameter mounting holes on 1" centers. One kit per pole line or load is required. Lugs are not provided. Ampere Rating A HCPCLP *For inches / millimeters conversion, multiply inches by s Built to order. Allow 6 8 weeks for delivery. a For horizontal mounting only in either 8" wide min switchboards or S5/F2 power panelboards. b Both 240 and V AC switches are also rated 2V DC max. 4- Siemens Canada Limited Power Product

21 Disconnect es Type HCP board Units Dimensions 4 DISCONNECT Siemens Canada Limited Power Product 4-21

22 Notes DISCONNECT Siemens Canada Limited Power Product