BUTTERFLY VALVES SHP SERIES. High Performance for a Wide Range of Applications. Advancedd seat and disc design provides zero

Transcription

1 UTTRLY VLVS SHP SRIS High Performance for a Wide Range of pplications dvancedd seat and disc design provides zero percent leakage capability at each valve s rated temperature/pressure while maintaining a low seating torque. Stainlesss steel disc and shaft on SHP series are standard for superior durability and long lasting operation.

2 utterfly Valve Nomenclature SHP SY2-24 MT Valve 6 = 2-way 7 = 3-way Valve Size 50 = 2 65 = 2½ 80 = = = = = = = = = = = = 24 Trim Material -150SHP = NSI lass 150, Stainless Disc, Steel Lug ody, RPT Seat, 0% Leakage up to 285 psi -300SHP = NSI lass 300, Stainless Disc, Steel Lug ody, RPT Seat, 0% Leakage up to 600 psi ctuator Type Non-Spring Return M... N4(H) M(X) SY lectronic ail-safe K Spring Return Power Supply -24 = 24 V/D -110 = 110/120 V -120 = 120 V -230 = 230 V UP = V or VD ontrol -3-X1 = On/Off, loating Point MT or MT-X1 = Multi-unction Technology -S = uilt-in uxiliary Switch N4 = NM 4/4X N4H = NM 4 with Heater Ordering xample 1 hoose the valve actuator combination SHP+SY2-24MT 2 2-way Preference Specify preference or confi guration. Set-Up 3 +NO or MT orders only - select programming code (consult factory) +Tagging (if needed) 3-way onfiguration 4 Does order require tagging? Non-Spring Return Spring Return 2 Pos. Modulating N NO NO/O N/ NO/ N/O Set Up Required ield Logic Determines Normal Position (Normally losed) 0.5 VD/2VD/4m = losed (Normally Open) 0.5 VD/2VD/4m = Open (Normally Open/ail Open) ield Logic Determines Normal Position Spring ails Valve OPN (Normally losed/ail losed) ield Logic Determines Normal Position Spring ails Valve LOSD (Normally Open/ail losed) 0.5 VD/2VD/4m = Open Spring ails Valve LOSD (Normally losed/ail Open) 0.5 VD/2VD/4m = losed Spring ails Valve OPN 2 Pos. Non-Spring Return Modulating Spring Return Modulating 2 Pos. Specify low Pattern S pecify low Pattern No Set Up Required ield Logic Determines Normal Position Master (ctuated) Valve N (Normally losed) 0.5 VD/2VD/4m = losed Master (ctuated) Valve NO (Normally Open) 0.5 VD/2 VD/4m = Open NO/O (Normally Open/ail Open) ield Logic Determines Normal Position Spring ails Master Valve OPN N/ (Normally losed/ail losed) ield Logic Determines Normal Position Spring ails Master Valve LOSD NO/O (Normally Open/ail Open) 0.5 VD/2 VD/4m = Master Valve Open Spring ails Master Valve OPN NO/ (Normally Open/ail losed) 0.5 VD/2 VD/4m = Maser Valve Open Spring ails Master Valve LOSD N/O (Normally losed/ail Open) 0.5 VD/2 VD/4m = Master Valve losed Spring ails Master Valve OPN N/ (Normally losed/ail losed) 0.5 VD/2 VD/4m = Master Valve losed Spring ails Master Valve LOSD Tagging: Valves may be tagged per customer specifi cation. ($10.00 per tag) xample: hiller 1 3rd loor ast Part number for tagging: omplete Ordering xample: SHP+SY2-24MT+NO + onsult factory

3 ontrol Valve Product Range High Performance utterfly Valve Product Range v 90 v 60 Valve Nominal Size Inches 2-way Valves NSI way Type NSI way SHP SHP ½ SHP SHP SHP SHP SHP SHP SHP SHP SHP SHP SHP SHP SHP SHP SHP SHP SHP SHP SHP SHP SHP SHP SHP SHP SHP SHP Non-Spring Return Suitable ctuators Spring Return lectronic ail-safe Note: v values listed for NSI lass 150 utterfly Valves. Please consult the technical documentation for NSI lass 300 v values and configurations. M Series M Series SY Series SY Series Series Series K Series K Series Mode of Operation High performance butterfly valves are designed for modulating and isolation service and feature a machined seat design and blow out proof solid shaft, providing better torque consistency, which offers longer actuator life and reduced risk of leakage. vailable for a variety of high temperature and pressure ratings i.e., SM/NSI lass 300 or 150. Valve sizes range from 2 to 24 inches, with rangebilities of 100:1, 0% leakage ratings, and a maximum valve velocity of 32 PS. Product eatures Unique body seat and double offset disc design ensures positive valve sealing to help assure leak free performance in water applications while maintaining low seating torque. ctuator Specifications ontrol type Manual override lectrical connection on/off, fl oating point, modulating, 2-10 VD, multi-function technology (MT) all models 3 ft. [1 m] cable terminal block Tech.Doc - 03/16 - Subject to change. elimo ircontrols (US), Inc. v 90 v 60 Valve Nominal Size Inches 3-way Valves NSI way Type NSI way SHP SHP ½ SHP SHP SHP SHP SHP SHP SHP SHP SHP SHP SHP SHP SHP SHP SHP SHP SHP SHP SHP SHP SHP SHP SHP SHP SHP SHP Suitable ctuators Non-Spring Return lectronic ail-safe Note: v values listed for NSI lass 150 utterfly Valves. Please consult the technical documentation for NSI lass 300 v values and configurations. M Series M SY Series SY Series K Series K Series Valve Specifications Service chilled or hot water, 60% glycol, steam to 50 psi low characteristic 6 modified equal percentage, unidirectional 7 modifi ed linear, unidirectional Sizes 2 to 24 nd fi tting SM/NSI lass 150 or 300 Materials ody carbon steel full lug Disc 316 stainless steel Shaft 17-4 PH stainless Seat RT land seal T earings glass backed PT Media temp. range -20 to +400 [-30 to +204 ] ody pressure rating 150 SHP: SM/NSI lass SHP: SM/NSI lass 300 lose-off pressure Rangeability 100:1 Maximum velocity Leakage 0% 150: 285 psi, 300: 600 psi 32 PS Double Dead nd Service: Utilizes larger retainer ring set screws to allow the valve to be placed at the end of the line without a down stream flange in either flow direction while still holding full pressure US ND LTIN MRI 3

4 eatures and enefits SHP Series High Performance utterfly Valves Valve Design eatures elimo SHP... Series utterfl y Valves are designed for use in NSI lass 150 and NSI lass 300 piping systems and are supplied in standard lug style body designs. Unique seat and disc design provides i-directional bubble tight shutoff at rated pressure/temperatures The Soft Seat design creates a self-energized seal in vacuum-to-low pressure applications Under high pressure conditions, the seat is also designed to permit, confi ne and direct movement of the seat against the disc edge, up to the full NSI lass 150 or 300 old Working Pressures The Soft Seat is designed for high services with minimal wear and low torque Seat replacement is a simple operation, requiring no special tools Valve ody is ull Lug type cast in arbon Steel Disc is cast in 8M Stainless Steel Shaft is 17-4pH Stainless for superior strength Soft Seat is RPT for increased wear resistance and low torque Top Mounted land lange easily accessible without removing actuator or mounting brackets KY Square key valve-to-operator connection provides an externally controlled failure point upon over-torquing. LND LN pplies load against packing gland to prevent external leakage. ully adjustable. PKIN hevron design T prevents external leakage out valve neck to full NSI hydrostatic shell test pressures (150% of.w.p.). WD RIN Stainless steel band wedged between valve body and retainer ring by set screws to lock seat and retainer ring in position on valve sizes 2 through 30. Socket head cap screws are used on valve sizes and larger. ST SRWS one point screws force wedge ring outward to lock seat retainer in position on valve sizes 2 through 30. Socket head cap screws are used on valve sizes and larger. OVRTRVL STOP Prevents disc from rotating into wrong quadrant. SOT-ST Patented bidirectional seat with encapsulated elastomeric o-ring core for resiliency. ommon seat materials include T, RT and UHMWP. LOW OUT PROO SHT Solid shaft provides alignment and rigid support for disc. PKIN LND Separate part from gland fl ange, preventing uneven load distribution against packing. RINS oth above and below the disc, bearings are of composite design: PT bonded to epoxy-glass fi lament wound ring. Used to align shaft, with high capacity, low wear and low friction coeffi cient. DIS SPRS Disc is centered by use of thrust spacers around shaft in sizes 2 to 5. Disc position stops or thrust bolt arrangements are used for larger valve sizes. WD PINS Provide positive mechanical attachment of disc to shaft. ODY NSI design in either wafer or lug configuration. DIS 0 uninterrupted spherical edge for sealing. Profile is designed for maximum fl ow and equal percentage control. RTINR RIN Retains seat in valve. Standard surface fi nish is 125 to 200 RH and is compatible with both standard gaskets and spiral wound gasket designs. Outside diameter is recessed within gasket sealing surface to prevent external leakage. Tech.Doc - 03/16 - Subject to change. elimo ircontrols (US), Inc US ND LTIN MRI / RIN

5 SHP Series utterfly Valves verage ssembly Weights NSI way 3-way TUTOR NON-SPRIN RTURN SPRIN RTURN LTRONI IL-S Size Valve Max PM OP M(X) 2*M(X) 2* K 2*K SHP lbs SHP lbs. 19 lbs. 2½ SHP lbs. 2½ SHP lbs 19 lbs SHP lbs SHP lbs. 21 lbs SHP lbs. 33 lbs SHP lbs. 42 lbs SHP lbs. 69 lbs. 2½ SHP lbs. 80 lbs SHP lbs. 90 lbs SHP lbs. 139 lbs. Tech.Doc - 03/16 - Subject to change. elimo ircontrols (US), Inc. NSI way 3-way TUTOR NON-SPRIN RTURN SPRIN RTURN LTRONI IL-S Size Valve Max PM OP M(X) 2*M(X) 2* K 2*K SHP lbs SHP lbs. 19 lbs. 2½ SHP lbs. 2½ SHP lbs. 19 lbs SHP lbs SHP lbs. 25 lbs SHP lbs. 32 lbs SHP lbs SHP lbs. 94 lbs. 2½ SHP lbs. 114 lbs SHP lbs. 1 lbs SHP lbs. 193 lbs. Max PM = Maximum US gallons of water (gpm) per minute, at room temperature, that will flow through the fully open valve without exceeding design velocity limits. OP = lose-off Pressure stated in psi. This is the maximum differential pressure the valve will close-off against while maintaining a bubble tight seal. ll SY series actuators are NM 4X rated and include 2 auxiliary switches and a heater US ND LTIN MRI / RIN 5

6 SHP Series utterfly Valves with Industrial ctuation NSI way 3-way TUTOR NON-SPRIN RTURN Size Valve Model Max PM OP SY2-110 SY3-110 SY4-110 SY5-110 SY7-110 SY8-110 SY9-110 SY SY SY SHP lbs. 2½ SHP lbs SHP lbs SHP lbs SHP lbs SHP lbs SHP lbs SHP lbs SHP lbs SHP lbs SHP lbs SHP lbs SHP lbs SHP lbs SHP lbs SHP lbs SHP lbs SHP lbs SHP lbs SHP lbs SHP lbs. 2½ SHP lbs SHP lbs SHP lbs SHP lbs SHP lbs SHP lbs SHP lbs SHP lbs SHP lbs SHP lbs SHP lbs SHP lbs lbs SHP lbs SHP lbs SHP lbs SHP lbs SHP lbs. Max PM = Maximum US gallons of water (gpm) per minute, at room temperature, that will flow through the fully open valve without exceeding design velocity limits. i OP = lose-off Pressure stated in psi. This is the maximum differential pressure the valve will close-off against while maintaining a bubble tight seal. ll SY series actuators are NM 4X rated and include 2 auxiliary switches and a heater. Tech.Doc - 03/16 - Subject to change. elimo ircontrols (US), Inc US ND LTIN MRI / RIN

7 SHP Series utterfly Valves with Industrial ctuation verage ssembly Weights Tech.Doc - 03/16 - Subject to change. elimo ircontrols (US), Inc. NSI way TUTOR NON-SPRIN RTURN Size Valve Model Max PM OP SY2-110 SY3-110 SY4-110 SY5-110 SY7-110 SY8-110 SY9-110 SY SY SHP lbs. 2½ SHP lbs SHP lbs SHP lbs SHP lbs SHP lbs SHP lbs SHP lbs SHP lbs SHP lbs SHP lbs SHP lbs SHP lbs SHP lbs SHP lbs SHP lbs SHP lbs SHP lbs SHP lbs SHP lbs SHP lbs SHP lbs SHP lbs SHP lbs SHP lbs SHP lbs SHP lbs SHP lbs SHP lbs SHP lbs. Max PM = Maximum US gallons of water (gpm) per minute, at room temperature, that will flow through the fully open valve without exceeding design velocity limits. OP = lose-off Pressure stated in psi. This is the maximum differential pressure the valve will close-off against while maintaining a bubble tight seal. ll SY series actuators are NM 4X rated and include 2 auxiliary switches and a heater US ND LTIN MRI / RIN 7

8 SHP Series utterfly Valves with Industrial ctuation verage ssembly Weights NSI way TUTOR NON-SPRIN RTURN Size Valve Model Max PM OP SY2-110 SY3-110 SY4-110 SY5-110 SY7-110 SY8-110 SY9-110 SY SY SY SHP lbs SHP lbs 2½ SHP lbs. 2½ SHP lbs SHP lbs SHP lbs SHP lbs SHP lbs SHP lbs SHP lbs SHP lbs SHP lbs SHP lbs SHP lbs SHP lbs SHP lbs SHP lbs SHP lbs SHP lbs SHP lbs SHP lbs SHP lbs SHP lbs SHP lbs SHP lbs SHP lbs SHP lbs SHP lbs SHP lbs SHP lbs SHP lbs SHP lbs SHP lbs. Max PM = Maximum US gallons of water (gpm) per minute, at room temperature, that will flow through the fully open valve without exceeding design velocity limits. OP = lose-off Pressure stated in psi. This is the maximum differential pressure the valve will close-off against while maintaining a bubble tight seal. ll SY series actuators are NM 4X rated and include 2 auxiliary switches and a heater. Tech.Doc - 03/16 - Subject to change. elimo ircontrols (US), Inc US ND LTIN MRI / RIN

9 utterfly Valve Selection-Velocity hart 150 SHP/300 SHP Series Valves SHP Series Valves are low Direction Specifi c MIXIN MSTR LOW OMMON OMMON LOW MSTR SLV LOW MSTR D145 OMMON SLV SLV DIVRTIN MSTR LOW OMMON OMMON MSTR SLV LOW MSTR OMMON SLV SLV Tech.Doc - 03/16 - Subject to change. elimo ircontrols (US), Inc. ONI OD M(D)10 M(D)11 M(D)12 M(D)13 M(D)14 ON/O OR MOD@2VD MSTR VLV IS OPN OPN OPN LOSD LOSD MSTR IL NON-IL OPN LOSD NON-IL OPN M(D)15 LOSD LOSD M Specifies MIXIN, D Specifies DIVRTIN ONI OD M(D)20 M(D)21 M(D)22 M(D)23 M(D)24 M(D)25 Notes: 1. Slave Valve operates inversely of the Master Valve. 2. The Master Valve is always located on the run. 3. The Slave Valve may also have an actuator if required (Direct oupled). ON/O OR MOD@2VD MSTR VLV IS OPN OPN OPN LOSD LOSD LOSD MSTR IL NON-IL OPN LOSD NON-IL OPN LOSD ONI OD M(D)30 M(D)31 M(D)32 M(D)33 M(D)34 M(D)35 ON/O OR MOD@2VD MSTR VLV IS OPN OPN OPN LOSD LOSD LOSD MSTR IL NON-IL OPN LOSD NON-IL OPN LOSD 4. On/Off actuator normal position is a function of field logic. 5. Proportional actuator normal position is a function of the W/W swit 6. ll 3-way assemblies are designed for 90 degree actuator rotation. low in Std Weight Pipe (luid Velocity in PM). Use with SHP Series Valves. SIZ 4 PS 8 PS 12 PS 16 PS 20 PS 24 PS 28 PS 32 PS PS ½ It is not recommended to exceed 32 feet per second through high performance butterfly valves. Velocities greater than 32 fps may damage the valve US ND LTIN MRI / RIN 9

10 eatures / enefits utterfly Valves SY Series ctuators elimo s SY series electric actuators have been designed to mate with our HD(U), rooved and SHP series butterfly valves and other quarter turn valve applications. The patented gear drive mechanism provides for efficient, smooth operation while allowing easy manual override at any time. Drawing upon years of experience in the actuation industry, we have incorporated the most desirable features into the SY product range. ll units have NM 4X ratings, easily visible position indicators, international standard ISO5211 mounting systems, internal thermal motor overload protection, heater, dual auxiliary orm switches, and easily accessible wiring termination points. Wiring diagrams, included in all printed documentation, are also affixed to the outside of the housing on the permanently attached product label. The units are easily visible in mechanical rooms with their characteristic elimo Orange color. Torque ranges are available from 310 to 31,150 in lbs. Domed Position Indicator ast luminum over Powder oated NM 4X Rated Housing our over Screws for asy ccess asily ccessible ield Wiring Terminal Positive Locking Switch ams ISO 5211Mounting System Thermally Protected Drive Motor Simple, Single Handed Override Wheel (SY2~12) Tech.Doc - 03/16 - Subject to change. elimo ircontrols (US), Inc. earing Seals Hardened Steel ear Sets US ND LTIN MRI / RIN

11 SY... Series Non-Spring Return ctuator Dimensions D SY-2~6... SY-1... D D SY-9~12... Tech.Doc - 03/16 - Subject to change. elimo ircontrols (US), Inc. MODL DIM (MX) SY-7~8... dd to Dim for cover removal DIM DIM (MX) DIM D Inches [mm] Inches [mm] Inches [mm] Inches [mm] Inches [mm] SY [155] 3.94 [100] 4.25 [108] 8mm - SY2~ [255] 7.48 [190] 7.87 [200] [330] 7.87 [200] SY4~ [315] 8.86 [225] 9.21 [234] [380] [300] SY7~ [420] 8.86 [225] 9.21 [234] [450] [340] SY9~ [590] 8.86 [225] [260] [470] [350] Note: ~ indicates range of actuator i.e., SY2~3 = SY-2 and SY US ND LTIN MRI / RIN 11

12 Wire Size vs. Length of Run for SY Series ctuators SY1 SY2 SY3 SY4 SY5 mps mps mps mps mps wire gauge MX Distance between ctuator and Supply (feet) V SY1 SY2 SY3 SY4 SY5 SY6 SY7 SY8 SY9 SY10 SY11 SY12 mps mps mps mps mps mps mps mps mps mps mps mps wire gauge MX Distance between ctuator and Supply (feet) V SY1 SY2 SY3 SY4 SY5 SY6 SY7 SY8 SY9 SY10 SY11 SY12 mps mps mps mps mps mps mps mps mps mps mps mps wire gauge MX Distance between ctuator and Supply (feet) V The N mandates that 24 V over 100 V power requires LSS 1 wiring conduit. Local codes may vary. Do NOT mix LSS 1 & LSS 2 circuits in the same conduit. enerally, 24 V actuators over 100 V should be changed to 120 V models. Tech.Doc - 03/16 - Subject to change. elimo ircontrols (US), Inc US ND LTIN MRI / RIN

13 utterfly Valve SY ctuators Power Supply Model Torque Speed 50 Hz/60 Hz urrent Draw urrent Draw 24 V/VD Single Phase W W V* SY in-lbs/ 35 Nm 20 seconds V* Override 8 mm Wrench Required Weight 2.0 kg/4.9 lbs. SY in-lbs/ 90 Nm 16 seconds Hand Wheel 11 kg/24.5 lbs. SY in-lbs/ 150 Nm 25 seconds Hand Wheel 11 kg/24.5 lbs. SY in-lbs/ 400 Nm 30 seconds Hand Wheel 22 kg/48.5 lbs. SY in-lbs/ 500 Nm 35 seconds Hand Wheel 22 kg/48.5 lbs. UTTRLY VLVS Power Supply Model Torque Speed 50 Hz Speed 60 Hz urrent Draw 120 V Single Phase urrent Draw SY in-lbs/ 35 Nm 17 seconds 12 seconds mm Wrench Required 2.0 kg/4.9 lbs. SY in-lbs/ 90 Nm 19 seconds 16 seconds Hand Wheel 11 kg/24.5 lbs. SY in-lbs/ 150 Nm 30 seconds 25 seconds Hand Wheel 11 kg/24.5 lbs. SY in-lbs/ 400 Nm 21 seconds 18 seconds Hand Wheel 22 kg/48.5 lbs. SY in-lbs/ 500 Nm 29 seconds 25 seconds Hand Wheel 22 kg/48.5 lbs. SY in-lbs/ 650 Nm 37 seconds 32 seconds Hand Wheel 22 kg/48.5 lbs. SY in-lbs/ 1000 Nm 59 seconds 49 seconds Hand Wheel kg/79.5 lbs. SY in-lbs/ 1500 Nm 60 seconds 50 seconds Hand Wheel kg/79.5 lbs. SY in-lbs/ 2000 Nm 68 seconds 57 seconds Hand Wheel 72 kg/176.4 lbs. SY in-lbs/ 2500 Nm 75 seconds 62 seconds Hand Wheel 72 kg/176.4 lbs. SY in-lbs/ 3000 Nm 78 seconds 69 seconds Hand Wheel 72 kg/176.4 lbs. SY in-lbs/ 3500 Nm 72 seconds 60 seconds Hand Wheel 72 kg/176.4 lbs. W W V* V* Override Weight Power Supply Model Torque Speed 50 Hz Speed 60 Hz urrent Draw 230 V Single Phase urrent Draw SY in-lbs/ 35 Nm 14 seconds 11 seconds mm Wrench Required 2.0 kg/4.9 lbs. SY in-lbs/ 90 Nm 19 seconds 15 seconds Hand Wheel 11 kg/24.5 lbs. SY in-lbs/ 150 Nm 30 seconds 25 seconds Hand Wheel 11 kg/24.5 lbs. SY in-lbs/ 400 Nm 21 seconds 18 seconds Hand Wheel 22 kg/48.5 lbs. SY in-lbs/ 500 Nm 29 seconds 25 seconds Hand Wheel 22 kg/48.5 lbs. SY in-lbs/ 650 Nm 38 seconds 31 seconds Hand Wheel 22 kg/48.5 lbs. SY in-lbs/ 1000 Nm 58 seconds 48 seconds Hand Wheel kg/79.5 lbs. SY in-lbs/ 1500 Nm 59 seconds 49 seconds Hand Wheel kg/79.5 lbs. SY in-lbs/ 2000 Nm 68 seconds 57 seconds Hand Wheel 72 kg/176.4 lbs. SY in-lbs/ 2500 Nm 73 seconds 62 seconds Hand Wheel 72 kg/176.4 lbs. SY in-lbs/ 3000 Nm 46 seconds 64 seconds Hand Wheel 72 kg/176.4 lbs. SY in-lbs/ 3500 Nm 74 seconds 61 seconds Hand Wheel 72 kg/176.4 lbs. W W V* V* Override Weight R /16 - Subject to change. elimo ircontrols (US), Inc. ll prices are in US Dollars (USD) *25% safety factor included in the V rating US ND LTIN MRI/RIN

14 utterfly Valve SY ctuators Power Supply Model Torque Speed 50 Hz/60 Hz urrent Draw urrent Draw 24 V/VD Single Phase W W V* SY1-24P 310 in-lbs/ 35 Nm 15 seconds V* Override 8 mm Wrench Required Weight 2.0 kg/4.9 lbs. SY2-24MT 800 in-lbs/ 90 Nm 16 seconds Hand Wheel 11 kg/24.5 lbs. SY3-24MT 1330 in-lbs/ 150 Nm 24 seconds Hand Wheel 11 kg/24.5 lbs. SY4-24MT 3540 in-lbs/ 400 Nm 23 seconds Hand Wheel 22 kg/48.5 lbs. SY5-24MT 4430 in-lbs/ 500 Nm 30 seconds Hand Wheel 22 kg/48.5 lbs. Power Supply Model Torque Speed 50 Hz Speed 60 Hz urrent Draw 120 V Single Phase urrent Draw SY1-120P 310 in-lbs/ 35 Nm 18 seconds 18 seconds mm Wrench Required 2.0 kg/4.9 lbs. SY2-120MT 800 in-lbs/ 90 Nm 14 seconds 15 seconds Hand Wheel 11 kg/24.5 lbs. SY3-120MT 1330 in-lbs/ 150 Nm 21 seconds 23 seconds Hand Wheel 11 kg/24.5 lbs. SY4-120MT 3540 in-lbs/ 400 Nm 16 seconds 17 seconds Hand Wheel 22 kg/48.5 lbs. SY5-120MT 4430 in-lbs/ 500 Nm 21 seconds 21 seconds Hand Wheel 22 kg/48.5 lbs. SY6-120MT 5750 in-lbs/ 650 Nm 28 seconds 29 seconds Hand Wheel 22 kg/48.5 lbs. SY7-120MT 8850 in-lbs/ 1000 Nm 41 seconds 44 seconds Hand Wheel kg/79.5 lbs. SY8-120MT in-lbs/ 1500 Nm 48 seconds 48 seconds Hand Wheel kg/79.5 lbs. SY9-120MT in-lbs/ 2000 Nm 47 seconds 47 seconds Hand Wheel 72 kg/176.4 lbs. SY10-120MT in-lbs/ 2500 Nm 52 seconds 51 seconds Hand Wheel 72 kg/176.4 lbs. SY11-120MT in-lbs/ 3000 Nm 55 seconds 56 seconds Hand Wheel 72 kg/176.4 lbs. SY12-120MT in-lbs/ 3500 Nm 61 seconds 62 seconds Hand Wheel 72 kg/176.4 lbs. W W V* V* Override Weight UTTRLY VLVS R /16 - Subject to change. elimo ircontrols (US), Inc. ll prices are in US Dollars (USD) Power Supply Model Torque Speed 50 Hz Speed 60 Hz urrent Draw 230 V Single Phase urrent Draw SY1-230P 310 in-lbs/ 35 Nm 16 seconds 16 seconds mm Wrench Required 2.0 kg/4.9 lbs. SY2-230MT 800 in-lbs/ 90 Nm 14 seconds 14 seconds Hand Wheel 11 kg/24.5 lbs. SY3-230MT 1330 in-lbs/ 150 Nm 23 seconds 23 seconds Hand Wheel 11 kg/24.5 lbs. SY4-230MT 3540 in-lbs/ 400 Nm 16 seconds 17 seconds Hand Wheel 22 kg/48.5 lbs. SY5-230MT 4430 in-lbs/ 500 Nm 22 seconds 22 seconds Hand Wheel 22 kg/48.5 lbs. SY6-230MT 5750 in-lbs/ 650 Nm 32 seconds 32 seconds Hand Wheel 22 kg/48.5 lbs. SY7-230MT 8850 in-lbs/ 1000 Nm 44 seconds 44 seconds Hand Wheel kg/79.5 lbs. SY8-230MT in-lbs/ 1500 Nm 55 seconds 57 seconds Hand Wheel kg/79.5 lbs. SY9-230MT in-lbs/ 2000 Nm 61 seconds 61 seconds Hand Wheel 72 kg/176.4 lbs. SY10-230MT in-lbs/ 2500 Nm 72 seconds 70 seconds Hand Wheel 72 kg/176.4 lbs. SY11-230MT in-lbs/ 3000 Nm 44 seconds 48 seconds Hand Wheel 72 kg/176.4 lbs. SY12-230MT in-lbs/ 3500 Nm 47 seconds 51 seconds Hand Wheel 72 kg/176.4 lbs. W W V* V* Override Weight *25% safety factor included in the V rating US ND LTIN MRI/RIN 19-9

15 Interface Wiring Detail SYx-MT, 24V, 120/230V ctuators: SYx-MT INSTLLTION NOTS UTION Notes: 1. Motor MS have been factory calibrated and should not be moved. 2. n adaption must be performed if any limit switch is adjusted. This will calibrate the beginning and end stopping points. Press the adaption button for 3 seconds and release. 3. New SY actuators must have an adaption performed before operation. P Tool Service Jack onnection ontrol Signal + ontrol Signal - DK + DK - Power Supply om - Power Supply Hot + daption ontrol Signal + ontrol Signal - DK + DK - Direction of Rotation 24V N - Power Supply ommon H - Power Supply Hot P Tool Service Jack daption Tech.Doc - 03/16 - Subject to change. elimo ircontrols (US), Inc. Direction of Rotation 120/230V US ND LTIN MRI / RIN

16 Interface Wiring Detail SYx-P LD Open LD lose N Power Supply (4) + Power Supply (5) ontrol Signal (6) ontrol Signal (7) Sensitivity switch setting is position #3 for factory default. To widen deadband, select a higher number (up to 9). Sensitivity eedback (11) eedback (12) VR2 VR1 INSTLLTION NOTS UTION Notes: 1. Do not change sensitivity or dip switch settings with power applied! 2. VR1 and VR2 are factory calibrated and should not be moved. 3. Motor MS have been factory calibrated and should not be moved. Dip Switch Settings O ON INPUT = 2-10 VD O ON RSPONS = DIRT O INPUT = 4-20m O RSPONS = RVRS ON ON Tech.Doc - 03/16 - Subject to change. elimo ircontrols (US), Inc. WRNIN Potentiometer (actory Pre-set) O ON O ON O ON INPUT = 1-5 VD OUTPUT = 4-20m OUTPUT = 2-10 VD or 2-position actuators with 1k feedback option Potentiometer points 1, 2, 3 are wired to terminal blocks 8, 9, 10. When a valve is closed: 8, 9 1k Ω 9, 10 0k Ω When a valve is opened: 8, 9 0k Ω 9, 10 1k Ω O ON O ON O ON LOSS O SINL = LOSD (Direct cting) LOSS O SINL = OPN (Reverse cting) LOSS O SINL = OPN (Direct cting) LOSS O SINL = LOSD (Reverse cting) LOSS O SINL = STOP *On modulating actuators DO NOT master/ slave using optional potentiometer. or modulating actuators with 1k feedback option* Potentiometer points 1, 2, 3 are wired to terminal blocks 8, 9, 10. When a valve is closed: 8, 9 1k Ω 9, 10 0k Ω When a valve is opened: 8, 9 0k Ω 9, 10 1k Ω US ND LTIN MRI / RIN 15

17 SY... Series Non-Spring Return ctuator UTION lectrical Travel djustment (actory Pre-set) SY-1 actory pre-set see chart below. ield adjustable if required uxiliary Switch for losed Indication LS2 LS1 uxiliary Switch for Opened Indication actory pre-set and calibrated. Do not adjust - warranty voided LS2 LOS lockwise Decrease losed ngle ounter-clockwise Increase losed ngle LS1 OPN lockwise Increase Opening ngle ounter-clockwise Decrease Opening ngle UTION lectrical Travel djustment SY-2-12 actory pre-set see chart below. ield adjustable if required uxiliary Switch for losed Indication uxiliary Switch for Opened Indication WRNIN D LS2 LS1 actory pre-set and calibrated. Do not adjust - warranty voided LS2 LOS LS1 OPN Switches at left are shown with actuator fully open D - D - lockwise Decrease losed ngle ounter-clockwise Increase losed ngle lockwise Increase Opening ngle ounter-clockwise Decrease Opening ngle Tech.Doc - 03/16 - Subject to change. elimo ircontrols (US), Inc. INSTLLTION NOTS UTION Notes: 1. n adaption must be performed when the limit switches are adjusted. or the SYx-MT actuators. This will calibrate the beginning and end stopping points. Press the adaption button for 3 seconds and release US ND LTIN MRI / RIN

18 W546_12 Wiring for ontrol Valves On/Off, 24V, 120/230V SY ctuator Wiring Diagram, SY1 5-24V On/Off SY V or 230V On/Off Tech.Doc - 03/16 - Subject to change. elimo ircontrols (US), Inc. Hazard Identification Warnings and autions appear at appropriate sections throughout this manual. Read these carefully. UTION Indicates a potentially hazardous situation which, if not avoided, may result in minor or moderate injury. It may also be used to alert against unsafe practices. Indicates an action or condition that may cause irreversible damage to the actuator(s) or associated equipment. quipment damage! Power consumption and input impedance must be observed. NOTS SY ach actuator should be powered by a single, isolated 33 control transformer. using a common control signal input. Line Volts Line Volts V Transformer 24V D Transformer Open lose Open lose round 1 ommon 3 Open 4 losed HTR round 1 Hot 3 Open 4 losed HTR INSTLLTION NOTS Observe class 1 and class 2 wiring restrictions. Transformer sizing = SY actuator draw X 1.25 (safety margin) (x. SY2-24 requires 3.0 x 1.25 = 3.75, 3.75 X 24 V = 90V Transformer). NOTS SY V or 230V aution: Power Supply Voltage using a common control signal input. 120V or 230V /D N L1 H L2 Open lose - (Open Indication) ontact Rating: V Max V Max. - (losed Indication) SY (Open Indication) ontact Rating: V Max V Max. - (losed Indication) SY1-110 (220) SY1 ontact rrangements round 1 ommon 3 Open 4 losed HTR D - (Open Indication) D- (losed Indication) ontact Rating: V Max. SY V or 230V US ND LTIN MRI / RIN 17

19 W547_11 Wiring for ontrol Valves Proportional, 24V, 120/230V SY ctuator Wiring Diagram, SY1-24P and SY1-110P (220P) Hazard Identification this manual. Read these carefully. UTION may result in minor or moderate injury. It may also be used to alert against unsafe practices. Indicates an action or condition that may cause irreversible damage to the actuator(s) or associated equipment. INSTLLTION NOTS 34 PPLITION NOTS round shielded wire at control panel chassis. Tape back ground at actuator. Use of feedback is optional. NOTS SY1 24P ach actuator should be powered by a single, isolated 33 control transformer. " " wiring to a common is prohibited. Terminals 4 and 6 need to be wired separately. NOTS SY1 110P (220P) aution: " " wiring to a common is prohibited. Terminals 4 and 6 need to be wired separately V /D Transformer round 120 or 230 V round Line Voltage 4 Power Supply om 5 Power Supply Hot N L1 H L2 4 Power Supply om 5 Power Supply Hot ontrol signal eedback 34 6 ontrol Signal (-) 7 ontrol Signal (+) eedback (-) 12 eedback (+) SY1-24P ontrol signal eedback 34 6 ontrol Signal (-) 7 ontrol Signal (+) eedback (-) 12 eedback (+) SY1-110P (220P) Tech.Doc - 03/16 - Subject to change. elimo ircontrols (US), Inc US ND LTIN MRI / RIN

20 W547_2_11 Wiring for ontrol Valves Proportional, 24V, 120/230V ctuator: SY2 5-24MT SY MT SY MT Hazard Identification this manual. Read these carefully. UTION Indicates a potentially hazardous situation which, if not avoided, may result in minor or moderate injury. It may also be used to alert against unsafe practices. Indicates an action or condition that may cause irreversible damage to the actuator(s) or associated equipment. INSTLLTION NOTS 34 PPLITION NOTS round shielded wire at control panel chassis. Tape back ground at actuator. Use of feedback is optional. NOTS SY MT ach actuator should be powered by a single, isolated 33 control transformer. " " wiring to a common is prohibited. NOTS SY MT (230MT) aution: P Tool Service Jack ontrol Signal eedback ontrol Signal (+) ontrol Signal (-) eedback Signal (+) Y 1 U5 ddress /- ~/+ Power Supply om Power Supply Hot 24V /D eedback Signal (-) Not Used daption 8 9 Tech.Doc - 03/16 - Subject to change. elimo ircontrols (US), Inc. ontrol Signal eedback 34 Not Used - P ontrol Signal (+) ontrol Signal (-) eedback Signal (+) eedback Signal (-) Not Used - Not Used - P 2 Y 1 U P Tool Service Jack 10 Y2 Y1 SYx-24MT Power Supply om 120v (N) / 230v (L1) Power Supply Hot 120v (H) / 230v (L2) N L daption ddress 8 Y1 9 Y2 SYx-120MT 10 SYx-230MT SY MT SY MT (230MT) US ND LTIN MRI / RIN 19

21 W549_11 Wiring for ontrol Valves On/Off, 24V, 110/120/230V SY ctuator Wiring Diagram, SY Multiple Wiring SY (220) Multiple Wiring Hazard Identification Warnings and autions appear at appropriate sections throughout this manual. Read these carefully. UTION Indicates a potentially hazardous situation which, if not avoided, may result in minor or moderate injury. It may also be used to alert against unsafe practices. Indicates an action or condition that may cause irreversible damage to the actuator(s) or associated equipment. quipment damage! Power consumption and input impedance must be observed. Isolation relays are required in parallel applications. The reason parallel applications need isolation relays is that the motor uses two sets of windings, one for each direction. When one is energized to turn the actuator in a specific direction a voltage is generated in the other due to the magnetic field created from the first. It s called back M. This is OK with one actuator because the voltage generated in the second winding isn t connected to anything so there is no flow; it has no magnetic effect on the motor. On parallel applications without isolation, this M voltage energizes the winding it is connected to on the other actuators in the system, the actuators are then trying to turn in both directions at once. The M voltage is always less than the supply voltage due to the resistance of the windings, so while the actuator still turns in the commanded direction, the drag from the other reduces the torque output and causes overheating. Line Voltage 24V Transformer Open lose K1 K1- K1- * * round 1 ommon 3 Open 4 losed HTR D - (Open Indication) D- (losed Indication) ontact Rating: V Max. SY round 1 ommon 3 Open 4 losed HTR D - (Open Indication) ctuator ctuator D- (losed Indication) ontact Rating: V Max. INSTLLTION NOTS Observe class 1 and class 2 wiring restrictions. Transformer sizing = SY actuator draw X 1.25 (safety margin) (x. SY2-24 requires 3.0 x 1.25 = 3.75, 3.75 X 24 V = 90V Transformer). NOTS aution: Power Supply Voltage. Isolation relays must be used in parallel connection of multiple actuators using a common control signal input. Should be DPDT. "H" (L2) cannot be connected to terminal #3 and #4 simultaneously. Required: Terminal #7 needs to be field wired to enable heater circuit. 120 or 230 V N L1 H L2 - (Open Indication) ontact Rating: V Max V Max. - (losed Indication) SY1-24 Open lose K1 SY1-110 (220) K1- K1- - (Open Indication) ontact Rating: V Max V Max. - (losed Indication) SY1 ontact rrangements round 1 ommon 3 Open 4 losed HTR D - (Open Indication) D- (losed Indication) ontact Rating: V Max. round 1 ommon 3 Open 4 losed HTR D SY (220) - (Open Indication) ctuator ctuator D- (losed Indication) ontact Rating: V Max. SY (220) Tech.Doc - 03/16 - Subject to change. elimo ircontrols (US), Inc. SY US ND LTIN MRI / RIN

22 W550_11 Wiring for ontrol Valves Proportional, 24V SY ctuator Wiring Diagram, SY1-24P Multiple Wiring Hazard Identification Warnings and autions appear at appropriate sections throughout this manual. Read these carefully. UTION Indicates a potentially hazardous situation which, if not avoided, may result in minor or moderate injury. It may also be used to alert against unsafe practices. 35 PPLITION NOTS Recommended twisted shielded pair for control wiring. round shielded wire at control panel chassis. Tape back ground at actuator. Use of feedback is optional. Tech.Doc - 03/16 - Subject to change. elimo ircontrols (US), Inc. Indicates an action or condition that may cause irreversible damage to the actuator(s) or associated equipment. quipment damage! Power consumption and input impedance must be observed. Isolation relays are required in parallel applications. The reason parallel applications need isolation relays is that the motor uses two sets of windings, one for each direction. When one is energized to turn the actuator in a specific direction a voltage is generated in the other due to the magnetic field created from the first. It s called back M. This is OK with one actuator because the voltage generated in the second winding isn t connected to anything so there is no flow; it has no magnetic effect on the motor. On parallel applications without isolation, this M voltage energizes the winding it is connected to on the other actuators in the system, the actuators are then trying to turn in both directions at once. The M voltage is always less than the supply voltage due to the resistance of the windings, so while the actuator still turns in the commanded direction the drag from the other reduces the torque output and causes overheating. INSTLLTION NOTS Observe class 1 and class 2 wiring restrictions. Transformer sizing = SY actuator draw X 1.25 (safety margin) (x. SY2-24 requires 3.0 x 1.25 = 3.75, 3.75 X 24 V = 90V Transformer). NOTS SY1-24P ach actuator should be powered by a single, isolated 33 control transformer. SY1-24P notes: Power supply om/neutral and ontrol Signal " " wiring to a common is prohibited. Terminals 4 and 6 need to be wired separately otherwise irreversible damage will occur. Do not change sensitivity or dip switch settings with power applied V /D Transformer Line Voltage 24V /D Transformer Line Voltage ontrol Signal 35 eedback () 35 eedback () round 4 Power Supply om 5 Power Supply Hot 6 ontrol Signal (-) 7 ontrol Signal (+) eedback (-) 12 eedback (+) SY1-24P round ctuator - (Open Indication) ontact Rating: V Max V Max. - (losed Indication) ctuator 4 Power Supply om 5 Power Supply Hot 6 ontrol Signal (-) 7 ontrol Signal (+) eedback (-) 12 eedback (+) - (Open Indication) ontact Rating: V Max V Max. - (losed Indication) SY1-24P US ND LTIN MRI / RIN 21

23 W550_2_11 Wiring for ontrol Valves Proportional, Multiple Wiring, 24V ctuators: SY MT Hazard Identification Warnings and autions appear at appropriate sections throughout this manual. Read these carefully. UTION Indicates a potentially hazardous situation which, if not avoided, may result in minor or moderate injury. It may also be used to alert against unsafe practices. Indicates an action or condition that may cause irreversible damage to the actuator(s) or associated equipment. quipment damage! Power consumption and input impedance must be observed. Isolation relays are required in parallel applications. The reason parallel applications need isolation relays is that the motor uses two sets of windings, one for each direction. When one is energized to turn the actuator in a specific direction a voltage is generated in the other due to the magnetic field created from the first. It s called back M. This is OK with one actuator because the voltage generated in the second winding isn t connected to anything so there is no flow; it has no magnetic effect on the motor. On parallel applications without isolation, this M voltage energizes the winding it is connected to on the other actuators in the system, the actuators are then trying to turn in both directions at once. The M voltage is always less than the supply voltage due to the resistance of the windings, so while the actuator still turns in the commanded direction, the drag from the other reduces the torque output and causes overheating. D - (Open Indication) D- (losed Indication) ontact Rating: V Max. SY2 5-24MT ontrol Signal eedback 35 ontrol Signal (+) ontrol Signal (-) eedback Signal (+) eedback Signal (-) Not Used - Not Used - ontrol Signal (+) ontrol Signal (-) P INSTLLTION NOTS Observe class 1 and class 2 wiring restrictions. Transformer sizing = SY actuator draw X 1.25 (safety margin) (x. SY2-24 requires 3.0 x 1.25 = 3.75, 3.75 X 24 V = 90V Transformer) ctuator Y 1 U ctuator Y 1 NOTS SY MT ach actuator should be powered by a single, isolated control transformer. PPLITION NOTS Recommended twisted shielded pair for control wiring. round shielded wire at control panel chassis. Tape back ground at actuator. Use of feedback is optional. ddress daption Y1 Y2 P Tool Service Jack P Tool Service Jack SYx-24MT ~/ /- /- ~/+ Power Supply om Power Supply Hot Power Supply om Power Supply Hot 24V /D 24V /D 33 Tech.Doc - 03/16 - Subject to change. elimo ircontrols (US), Inc. eedback eedback Signal (+) U5 ddress eedback Signal (-) Not Used daption 8 9 Not Used - 2 Y1 Y2 SYx-24MT 10 P US ND LTIN MRI / RIN

24 W552_1_11 Proportional, 110/220V, 120/230V ctuators: SY1-110P SY1-220P Hazard Identification 120 or 230 V round Warnings and autions appear at appropriate N L1 4 Power Supply om sections throughout this manual. Read these carefully. H L2 5 Power Supply Hot UTION 6 ontrol Signal (-) Indicates a potentially hazardous situation which, if 7 ontrol Signal (+) not avoided, may result in minor or moderate injury. It may also be used to alert against unsafe practices Indicates an action or condition that may cause irreversible damage to the actuator(s) or associated equipment. quipment damage! Power consumption and input impedance must be observed. INSTLLTION NOTS Observe class 1 and class 2 wiring restrictions. eedback () ctuator eedback (-) 12 eedback (+) - (Open Indication) ontact Rating: V Max V Max. - (losed Indication) SY1-110P (220P) PPLITION NOTS round ctuator Tech.Doc - 03/16 - Subject to change. elimo ircontrols (US), Inc. 35 Recommended twisted shielded pair for control wiring. round shielded wire at control panel chassis. Tape back ground at actuator. Use of feedback is optional. NOTS SY1-110P (220P) aution: Power supply voltage. power applied. ontrol Signal 35 eedback () 4 Power Supply om 5 Power Supply Hot 6 ontrol Signal (-) 7 ontrol Signal (+) eedback (-) 12 eedback (+) - (Open Indication) ontact Rating: V Max V Max. - (losed Indication) SY1-110P (220P) US ND LTIN MRI / RIN 23

25 W552_2 Wiring for ontrol Valves Proportional, Multiple Wiring, 120/230V ctuators: SY MT SY MT Hazard Identification Warnings and autions appear at appropriate sections throughout this manual. Read these carefully. UTION Indicates a potentially hazardous situation which, if not avoided, may result in minor or moderate injury. It may also be used to alert against unsafe practices. Indicates an action or condition that may cause irreversible damage to the actuator(s) or associated equipment. quipment damage! Power consumption and input impedance must be observed. Isolation relays are required in parallel applications. The reason parallel applications need isolation relays is that the motor uses two sets of windings, one for each direction. When one is energized to turn the actuator in a specific direction a voltage is generated in the other due to the magnetic field created from the first. It s called back M. This is OK with one actuator because the voltage generated in the second winding isn t connected to anything so there is no flow; it has no magnetic effect on the motor. On parallel applications without isolation, this M voltage energizes the winding it is connected to on the other actuators in the system, the actuators are then trying to turn in both directions at once. The M voltage is always less than the supply voltage due to the resistance of the windings, so while the actuator still turns in the commanded direction, the drag from the other reduces the torque output and causes overheating. ontrol Signal (+) INSTLLTION NOTS Observe class 1 and class 2 wiring restrictions. 35 PPLITION NOTS Recommended twisted shielded pair for control wiring. round shielded wire at control panel chassis. Tape back ground at actuator. Use of feedback is optional. NOTS SY MT (230MT) aution: Power supply voltage. Y P Tool Service Jack N L Power Supply om 120 V (N) / 230 V (L1) Power Supply Hot 120 V (H) / 230 V (L2) 1 ontrol Signal (-) (Open Indication) D D- (losed Indication) ontact Rating: V Max. SY MT SY MT ontrol Signal eedback eedback eedback Signal (+) eedback Signal (-) Not Used - Not Used - P ontrol Signal (+) ontrol Signal (-) eedback Signal (+) eedback Signal (-) Not Used - Not Used - U ctuator Y 1 U P Tool Service Jack daption SYx-120MT SYx-230MT daption N L 3 ddress 8 Y1 9 Y2 10 Power Supply om 120 V (N) / 230 V (L1) Power Supply Hot 120 V (H) / 230 V (L2) ddress Tech.Doc - 03/16 - Subject to change. elimo ircontrols (US), Inc. 8 P ctuator SYx-120MT SYx-230MT Y1 Y US ND LTIN MRI / RIN

26 Installation Recommendations SHP Series utterfly Valves Valve Design 1. The SHP Series High Performance utterfly Valve features a double offset (or, double eccentric) shaft design to minimize seat abrasion and lower torque. This double offset design allows the disc to lift off and cam away from the seat as it rotates open. 2. The SHP valve always rotates clockwise to close (when viewed from above) and counterclockwise to open. 3. The valve body has an Overtravel Stop which prevents the disc from over rotating into the wrong quadrant. This stop is not to be used as a disc position stop; if the disc contacts the Overtravel Stop, this means it has rotated beyond the seat. 4. The SHP valve is bidirectional, but the preferred installation position is with the seat in the upstream position (SUS). Note the arrow on the metal tag attached to the valve body. Safety Precautions 1. e sure the line is depressurized and drained. 2. e sure of the pipeline media. Proper care should be taken for protection against toxic and/or flammable fluids. 3. Never install the valve without an Operator (Manual or utomatic) already attached to the valve shaft. 4. Never remove the Operator from the valve while the valve is in the pipeline under pressure. 5. lways be sure that the disc is in the full-closed position before installing the valve. 6. Take care in handling the valve; if you treat it like a machine, it will operate like a machine if you treat it like a piece of pipe, it may work like a piece of pipe. Pipe Schedule ompatibility The SHP valve is designed to allow the disc edge to rotate into the open position without interference with the pipeline I.D. in the following pipe schedules: SIZ NSI 150 NSI SH 80 SH SH 40 SH SH 30 SH STD WT 48 XS Product Identification 1. very SHP valve has a metal identification tag attached to the valve body. Information includes the igure Number, the Size and Pressure lass, the Materials of onstruction, and the Operating Pressures and Temperatures. 2. very SHP valve is hydrostatically tested before it is shipped. The metal tag also includes a Serial Number; this number, unique for each valve, is recorded by the elimo Quality ontrol Department along with the test results and material certification data, for individual traceability and verification of every valve produced. SHP series valves have a preferred flow direction. Preferredlowrate Tech.Doc - 03/16 - Subject to change. elimo ircontrols (US), Inc. lange ompatibility The SHP valve is designed to fit between flanges as follows: NSI lass to 24 MSS SP-44 lass to 48 NSI lass 150 langes NSI lass to 24 MSS SP-44 lass NSI lass 200 langes asket ompatibility The SHP valve is designed to accommodate the use of standard fiber gaskets (such as non-asbestos, flexible graphite, asbestos or equivalent gasket materials) of 1/16 or less, meeting the dimensional requirements of NSI Thick elastomeric gaskets are not recommended. Metallic wound (lexitallic) gaskets may also be used. UNPKIN ND STOR INSTRUTIONS 1. heck the packing list against the valve received to verify that the quantities, sizes and materials are correct. 2. heck to make sure that the valve and operator were not damaged during shipment. 3. If the valve is to be stored before being installed, it should be protected from harsh environmental conditions. 4. Store the valve with the disc in the closed position to protect the sealing edge and the seat. 5. Keep the valve in a clean location, away from dirt, debris and corrosive materials. 6. Keep the valve in a dry area with the flange protectors attached. 7. Keep the valve in a cool location if possible, out of direct sunlight. 8. If not in use, exercise the butterfly valve (full open and close) at least once a month US ND LTIN MRI / RIN 25

27 Installation Recommendations SHP Series utterfly Valves SHP Series utterfly Valves Storage of utterfly Valve ssemblies ssemblies must be stored indoors, protected from the elements. Materials received on job sites that have long installation lead times should receive extra protection from construction damage. Valve faces must be protected from abrasion, cutting and nicking, as this will damage the face and may cause flange area leaks. lectric actuators cannot be stored in wet, damp or caustic areas. Do not store construction material on top of valve assemblies. Installation Practices SHP series butterfly valves are designed to be installed between NSI 125/150 flat-faced or raised face, slip-on weld neck flanges. Valve should be installed a minimum of 6 pipe diameters from upstream or downstream elbows, strainers, pumps, etc. or chilled water, condenser water or hot water applications, the valve should be installed with the stem in a vertical orientation, with the actuator mounted above the valve. or applications in which there is a possibility of sediment in the flow, the valve should be installed with the stem in a horizontal position and the bottom of the disc should close ROM the downstream side, rather than from the upstream side. lange gaskets must be used on SHP series valves. Make sure the flange faces are clean and free of rust, scale and debris to prevent damage to the flange gasket. ollow the recommended flange bolting sequence found in the Installation Recommendations section of this guide. Installation using Welded langes Mount flanges on both sides of valve body and install bolts to properly align valve body and both flanges. Make sure the valve I.D. and flange internal diameters are in alignment. Take valve body / flange pair assembly and align with piping ends. TK weld the flanges to the piping in several places. Do NOT seam weld at this time! Remove the lug bolts and carefully remove the valve body from the flanges. Seam weld the entire flange / piping connection for both flanges. Let the piping components cool completely before re-inserting the valve body. WRNIN! Seam welding with the valve body installed between the flanges can damage the valve seats due to heat migration through the flange to the valve body. utterfl y Sizing and Selection ONSULT HRT ON P 21 (low in Standard Weight Pipe-luid Velocity in PM). or SHP Series utterfly Valves, the 32 ft/second column is applied. or example: pplication requires a 2-way, 600 PM utterfly valve, a valve of 3 minimum would be selected. The 3 valve at 32 ft/second would be able to withstand a capacity of 705 PM, without damage to the seat. Notes 1. Most utterflies are line size and piping geometry is not considered. If valve size must be reduced, a recommendation is to select a valve only one size less than the pipe. (Do not exceed velocity limit) 2. or a modulating utterfly valve, the v rating is determined at 60 open. or a 2-position utterfly valve, the v is determined at 90 open. onsult elimo Technical Support for applications involving steam, high velocity requirements, etc. Tech.Doc - 03/16 - Subject to change. elimo ircontrols (US), Inc US ND LTIN MRI / RIN

28 Installation Recommendations SHP Series utterfly Valves Pre-Installation Procedure 1. Remove the protective face covers from the valve. 2. Inspect the valve to be certain the waterway is free from dirt and foreign matter. e certain the adjoining pipeline is free from any foreign material such as rust and pipe scale or welding slag that could damage the seat and disc sealing surfaces. 3. ctuators should be mounted on the valve prior to installation to facilitate proper alignment of the disc in the valve seat. 4. The valve should be in the closed position. Make sure the open and closed positions of the actuator correspond to the counter-clockwise to open direction of rotation of the valve. 5. ycle the valve to the fully open position, then back to the fully closed position, checking the actuator travel stop settings for proper disc alignment. 6. heck the valve identifi cation tag for valve class, materials, and operating pressure to be sure they are correct for the application. WRNIN! Personal injury or property damage may result if the valve is installed where service conditions could exceed the valve ratings. 7. heck the flange bolts or studs for proper size, threading, and length. RMMR: Install the valve with the disc in the full-closed position using the appropriate flange gaskets on OTH valve flange faces. NOT ctuator must be mounted at or above pipe center line for all actuator types Valve Installation Procedure The SHP High Performance utterfl y Valve can be installed in the pipeline with the shaft in the vertical, horizontal, or other intermediate position. ased on applications experience, however, in media with concentrations of solid or abrasive particles or media subject to solidifi cation buildup, valve performance and service life will be enhanced by mounting the valve with the shaft in the horizontal position. ig. 8 Tech.Doc - 03/16 - Subject to change. elimo ircontrols (US), Inc. ll SHP valves are bidirectional and can be mounted in the pipeline in either fl ow direction; however, the preferred fl ow direction for all seat styles and materials is with the seat retainer ring located upstream (sus) to provide maximum seat protection. or SHP Series valves a. Noting the fl ow direction arrow on the tag, place the valve between the fl anges, making sure the arrow on the tag points in the direction of the fl ow. b. Install the lower fl ange bolts loosely, leaving space for the fl ange gaskets. c. fter inserting the fl ange gaskets, install the remaining bolts. 3. Using the sequence shown to the right, tighten the fl ange bolts evenly to assure uniform gasket compression. UTION: The SHP valve should be centered between the fl anges and gaskets to prevent damage to the disc edge and shaft as a result of the disc striking the fl ange, gasket, or pipe. 4. lectricity should be connected to the unit as specifi ed by the actuator manufacturer. 5. The valve is now ready for operation US ND LTIN MRI / RIN 27

29 Installation Recommendations SHP Series utterfly Valves LN OLTIN ROMMNDTIONS Lug Valves, 2 30, NSI 125/150 olt Pattern STUDS & NUTS MHIN OLTS Valve Size Thread Size QTY LNTH D QTY LNTH QTY LNTH QTY LNTH 2 5/ /2 5/ / / / / / / / / / /8-8 4** ** * ** / / /4-8 4** ** * ** 4.63 LU ODY HX HD MHIN OLTS LU ODY STUDS and NUTS olting and torque recommendations are made without warranty, and apply only to steel weld-neck or slip-on flanges. The use of lock washers and/or lubrication with the bolting will affect stated torque values. Length of machine bolts based on: 1. asket thickness of 0.06 inches. 2. Minimum flange thickness of weld-neck flanges per NSI 16.5 and Series. * Variation to specified bolting length may result in improper installation. LN OLTIN ROMMNDTIONS lange Detail for NSI Pipe langes 150 SHP Series utterfly Valves LNS DRILLIN OLTIN Nominal Diameter of Diameter of Number olt ircle olt Holes of olts Pipe Size lange Diameter lange Thickness D Diameter of olts 2 6 3/4 4-3/4 3/4 4 5/8 2-1/2 7 7/8 5-1/2 3/4 4 5/ /2 15/16 6 3/4 4 5/ /16 7-1/2 3/4 8 5/ /16 8-1/2 7/8 8 3/ /2 7/8 8 3/ /2 1-1/8 11-3/4 7/8 8 3/ / / / / / /8 18-3/4 1-1/ /2 1-7/ /4 1-1/ /8 22-3/4 1-1/ / /2 1-11/ / / /8 29-1/2 1-3/ /4 Tech.Doc - 03/16 - Subject to change. elimo ircontrols (US), Inc. very effort is made to provide accurate information, but no liability for claims arising from erroneous data will be accepted by elimo US ND LTIN MRI / RIN

30 Installation Recommendations SHP Series utterfly Valves LN OLTIN ROMMNDTIONS Lug Valves, 2-24, NSI 250/300 olt Pattern OLT NMNT IN VLV* STUDS & NUTS MHIN OLTS Valve Size Thread Size QTY LNTH QTY LNTH QTY LNTH D QTY LNTH QTY LNTH QTY LNTH 2 5/ /2 5/ / / / / / / / /8-8 4** ** ** ** ** ** / /4-8 4** ** ** ** ** ** / /4-8 4** ** ** ** ** ** / /4-8 4** ** ** ** ** ** / /2-8 4** ** ** ** ** ** 4.50 LU ODY HX HD MHIN OLTS LU ODY STUDS and NUTS * olt lengths & are from face of valve body to minimum depth in lug. lange & gasket thickness must be added to calculate minimum bolt length. **Special length required for tapped blind holes on either side of the valve shaft at the top and bottom ends of the valve body. Tech.Doc - 03/16 - Subject to change. elimo ircontrols (US), Inc. LN OLTIN ROMMNDTIONS lange Detail for NSI Pipe langes 300 SHP Series utterfl y Valves LNS DRILLIN OLTIN Nominal Diameter of Diameter of Number olt ircle olt Holes of olts Pipe Size lange Diameter lange Thickness D Diameter of olts /8 2-1/ / / / / / / / / / / / / US ND LTIN MRI / RIN 29