Technical Documentation Ball Valves

Transcription

1 Technical Documentation all Valves Effective October 2008 elimo Project: ssisi Heights in ochester, Minnesota

2 all Valves all Valve Features and enefits 2...VS/VSS, 3...VS, 6...VS K /08 - Subject to change. elimo ircontrols (US), Inc. 2-way and 3-ay configuration ronze with stainless steel trim educed and full port capacities Two piece construction Electronic actuation NPT and Flanged connections ide C v range ir gap for use with hot water and steam systems Live load low maintenance stem packing 2 Year arranty 1

3 Flow Pattern, Operation and Installation all Valves Flow Pattern Closed CC Flow Direction Open C C to Flow Direction CC to Note: 3 VS are piped differently than 3 CCV Valves. VS Series all Valve Piping Diagrams Piping/Mounting Orientation ssembly can be mounted horizontally or vertically. Do not install with actuator below pipe. K /08 - Subject to change. elimo ircontrols (US), Inc. 2

4 Piping Sizing Geometry all Valves Pipe Valve Valve Part C Size v Type Number FpCv FpCv FpCv FpCv FpCv FpCv FpCv FpCv FpCv FpCv FpCv FpCv ½ 1 2 NPT 2VS ½ 2 2 NPT 3VS ½ 4 2 NPT 4VS ½ 15 2 NPT 5VS ¾ 30 2 NPT 9VS ¾ 51 2 NPT 220VS NPT 224VS NPT 225VS ¼ 48 2 NPT 2VS ½ 84 2 NPT 9VS ½ NPT 240VS NPT 249VS NPT 250VS ½ NPT 265VS NPT 280VS ½ 5 3 NPT 315VS ¾ 11 3 NPT 320VS NPT 325VS ¼ 33 3 NPT 332VS ½ 49 3 NPT 340VS NPT 350VS FLG 650VS ½ FLG 665VS FLG 680VS FLG 6100VS FLG 6150VS FLG 6200VS FLG 6250VS Fp Cv also apply to VSS where applicable. K /08 - Subject to change. elimo ircontrols (US), Inc. 3

5 iring Instructions all Valves General iring Instructions NING The wiring technician must be trained and experienced with electronic circuits. Disconnect power supply before attempting any wiring connections or changes. Make all connections in accordance with wiring diagrams and follow all applicable local and national codes. Provide disconnect and overload protection as required. Use copper, twisted pair, conductors only. If using electrical conduit, the attachment to the actuator must be made with flexible conduit. lways read the controller manufacturer s installation literature carefully before making any connections. Follow all instructions in this literature. If you have any questions, contact the controller manufacturer and/or elimo. Transformer(s) Typically actuators require a 24 VC class 2 transformer and draw a maximum of 10 V per actuator. The actuator enclosure cannot be opened in the field, there are no parts or components to be replaced or repaired. EMC directive: 89/336/EEC Software class : Mode of operation type 1 Low voltage directive: 73//EEC Typical transformer sizing ctuator Series Voltage Max. V Per ctuator F NF LF 24 6 GM 24 7 M 24 6 NM 24 4 LM 24 3 CUTION It is good practice to power electronic or digital controllers from a separate power transformer than that used for actuators or other end devices. The power supply design in our actuators and other end devices use half wave rectification. Some controllers use full wave rectification. hen these two different types of power supplies are connected to the same power transformer and the DC commons are connected together, a short circuit is created across one of the diodes in the full wave power supply, damaging the controller. Only use a single power transformer to power the controller and actuator if you know the controller power supply uses half wave rectification. Multiple actuators, one transformer Multiple actuators may be powered from one transformer provided the following rules are followed: 1. The TOTL current draw of the actuators (V rating) is less than or equal to the rating of the transformer. 2. Polarity on the secondary of the transformer is strictly followed. This means that all No. 1 wires from all actuators are connected to the common leg on the transformer and all No. 2 wires from all actuators are connected to the hotleg. Mixing wire No. 1 & 2 on one leg of the transformer will result in erratic operation or failure of the actuator and/or controls. Multiple actuators, multiple transformers Multiple actuators positioned by the same control signal may be powered from multiple transformers provided the following rules are followed: 1. The transformers are properly sized. 2. ll No. 1 wires from all actuators are tied together and tied to the negative leg of the control signal. See wiring diagram. ire Type and ire Installation Tips For most installations, 18 or 16 Ga. cable works well with elimo actuators. Use code-approved wire nuts, terminal strips or solderless connectors where wires are joined. It is good practice to run control wires unspliced from the actuator to the controller. If splices are unavoidable, make sure the splice can be reached for possible maintenance. Tape and/or wire-tie the splice to reduce the possibility of the splice being inadvertently pulled apart. ire length for actuator installation Keep power wire runs below the lengths listed in the following tables. If more than one actuator is powered from the same wire run, divide the allowable wire length by the number of actuators to determine the maximum run to any single actuator. See section 1 for specific transformer sizing information for the actuator selected. Example: 3 actuators, 16 Ga wire 350 Ft 3 ctuators = 117 Ft. Maximum wire run K /08 - Subject to change. elimo ircontrols (US), Inc. 4

6 Nomenclature all Valves 2 24 VS MX 24 -MFTX1 Valve 2 = 2-way 3 = 3-way 6 = 2-way Flanged Valve Size = 1/ = 2 10 (Flanged) Trim Material VS = ronze or Cast Iron ody, Stainless Steel all and Stem VSS = Stainless Steel ody, all and Stem ctuator Type Non-Spring eturn LM NM M GM SY SY P Spring eturn LF NF F SY Power Supply 24 = 24 VC/DC 120 = 120 VC 0 = 0 VC Control -3X1 = On/Off, Floating Point -MFTX1 = Multi-Function Technology -MFT95 = Ω -S = uilt-in uxiliary Switch Ordering Example K /08 - Subject to change. elimo ircontrols (US), Inc. 1 Choose the valve actuator combination. 224VS+MX24-MFTX1 +NO +Tagging (if needed) 2 Specify preference or configuration. Non-Spring Models NO = Normally Open NC = Normally Closed Spring eturn Models NO/FO = Normally Open/Fail Open NO/FC = Normally Open/Fail Closed NC/FO = Normally Closed/Fail Open NC/FC = Normally Closed/Fail Closed efers to valve ports to. 3 Set-Up For MFT orders only - select programming code P (01) P-100xx (xx) Control voltage applications P-200xx (xx) Pulse width modulation applications P-300xx (Fxx) P-400xx (Jxx) X-XXXXX X-XXXXX Floating Point applications On/Off applications Create custom MFT configuration code Create custom MFT configuration in the field with MFT-actuator PC software Does order require tagging? Tagging: Valves may be tagged per customer specification. Example: HU-1 FCU Complete Ordering Example: 224VS+MX24-MFTX1+NO+01 5

7 2...VS Series, 2-ay, all Valve ronze ody, Stainless Steel all and Stem Live-load packing set Stainless steel ball & stem low-out proof stem design Technical Data Media Chilled or hot water, glycol, 35# steam Flow Characteristic Modified equal percentage ction 90 rotation valve open C, valve closed CC Sizes ½, ¾, 1, 1¼, 1½, 2, 2½, 3 Type of end fitting SE NPT (Female Connections) Materials: 1 Stem Packing einforced PTFE 2 Stem earing einforced PTFE 3 all 316 Stainless Steel 4 Seat (x2) einforced PTFE w/ Durafill 5 etainer 16 (¾ - 1 ) rass 584 (1¼ - 3 ) rass 6 Gland 16 rass 7 Stem 316 Stainless Steel 8 Jam Nut Stainless Steel 9 ody Seal PTFE (1-1/4 to 3 ) 10 ody 584-C84400 ronze pplication This valve is typically used in air handling units on heating or cooling coils, and fan coil unit heating or cooling coils. Some other common applications include Unit Ventilators, VV ox re-heat coils and bypass loops. This valve is suitable for use in a hydronic system with variable flow. This valve is designed with MFT functionality which facilitates the use of various control input. Up to 35 psi steam 1/2-600 PSIG OG, Cold Non-Shock. Federal Specification: -V-35C,Type II Composition: Z Style: 3 Valve Nominal Size Type Suitable eturn ctuators C v Inches DN [mm] 2-way NPT Spring Non-Spring 1 ½ 15 2VS 2 ½ 15 3VS 4 ½ 15 4VS 15 ½ 15 5VS 30 ¾ 20 9VS 51 ¾ VS VS VS 48 1¼ 32 2VS 84 1½ 40 9VS 177 1½ VS VS VS 503 2½ VS VS LF Series NF F Series LM Series NM M Series GM Series SY Series Pressure rating 600 psig OG Media temp. range -22 F to 280 F (-30 C to 138 C) Close-off pressure F Maximum differential <600 psig pressure ( P) Flow Patterns K /08 - Subject to change. elimo ircontrols (US), Inc. 6

8 2...VSS Series, 2-ay, all Valve Stainless Steel ody, all and Stem Live-load packing set Stainless steel ball & stem low-out proof stem design pplication These threaded valves are designed to provide modulating or two position control of hot or chilled water and saturated steam systems under 50 psi. Typical applications include reheat coils, vav terminal control, unit ventilators, and air handlers, especially in areas which have minimum profile requirements. Up to 50 psi steam 1/ PSIG OG, Cold Non-Shock. Federal Specification: -V-35C,Type II, Composition: SS Style: 3 Technical Data Media Chilled or hot water, glycol, 50# steam Flow Characteristic Modified equal percentage ction 90 rotation valve open C, valve closed CC Sizes ½, ¾, 1, 1¼, 1½, 2, 2½ Type of end fitting SE NPT (Female Connections) Materials: 1 Stem Packing einforced PTFE 2 Stem earing einforced PTFE 3 all 316 Stainless Steel 4 Seat (x2) einforced PTFE w/ Durafill 5 etainer 16 (¾ - 1 ) rass 584 (1¼ - 3 ) rass 6 Gland Stem 316 Stainless Steel 8 Jam Nut Stainless Steel 9 ody Seal PTFE (1¼ to 3 ) 10 ody 351-CF8M 316 Stainless Steel Valve Nominal Size Type Suitable eturn ctuators C v Inches DN [mm] 2-way NPT Spring Non- Spring 15 ½ 15 5VSS 30 ¾ 20 9VSS VSS 48 1¼ 32 2VSS 84 1½ 40 9VSS VSS 503 2½ VSS LF Series F Series NM Series M Series GM Series SY Series K /08 - Subject to change. elimo ircontrols (US), Inc. Pressure rating 2000 psig OG (½ - 1 ) Media temp. range -22 F to 298 F (-30 C to 148 C) Close-off pressure F Maximum differential <600 psig pressure ( P) Flow Patterns 7

9 3...VS Series, 3-ay, all Valve ronze ody, Stainless Steel all and Stem 316 Stainless all and Stem einforced PTFE seats and stuffing box low-out proof stem design djustable packing gland pplication These threaded valves are designed to provide modulating or two position control of hot or chilled water. Typical applications include reheat coils, vav terminal control, unit ventilators, and air handlers, especially in areas which have minimum profile requirements. 400 PSIG OG, Cold Non-Shock Technical Data Media Chilled or hot water, glycol Flow Characteristic Modified equal percentage ction 90 rotation to open CC, to open C Sizes ½, ¾, 1, 1¼, 1½, 2 Type of end fitting SE NPT (Female Connection) Materials: 1 Stem Packing PTFE 2 Stem earing PTFE 3 all 316 Stainless Steel 4 Seat (x2) PTFE w/ Durafill 5 etainer 16 (½ - 1 ) rass 584 (1¼ - 2 ) rass 6 Gland STM 16 rass 7 Stem 316 Stainless steel 8 Jam Nut PTFE (1¼ - 2 ) 9 ody Seal 584-C84400 ronze Valve Nominal Size Type Suitable eturn ctuators C v Inches DN [mm] 3-way NPT Spring Non-Spring 4.8 ½ VS 11 ¾ VS VS 33 1¼ VS 49 1½ VS VS LF NF F Series NF LM NM Series M GM Series Pressure rating 400 psig OG Media temp. range -22 F to 250 F (-30 C to 120 C) Close-off pressure F Maximum differential <75 psig pressure ( P) Flow Patterns K /08 - Subject to change. elimo ircontrols (US), Inc. 8

10 6...VS Series, 2-ay, all Valve Cast Iron ody, Stainless Steel all and Stem Same end to end dimension as conventional flanged iron gate valve Fast quarter turn open or closed operation Stainless steel ball and stem Positive shut-off Two-piece body construction Technical Data Media Chilled or hot water, glycol, 50# steam Flow Characteristic Modified equal percentage ction 90% rotation valve open C, valve closed CC Sizes 2, 2½, 3, 4, 6, 8, 10 Type of end fittings Flanged 125# NSI olt Pattern Materials: 1 ody Cast Iron - STM 126 Class 2 End Cap Cast Iron - STM 126 Class 3 all 304 Stainless Steel - STM Seats PTFE 5 Stem 304 Stainless Steel - ISI Packing PTFE 7 Gland Cast Iron - STM 126 Class 8 Gasket PTFE 9 Nut Steel - STM 6 pplication Ideal for water service where a non-corrosive, clean cosmetic appearance is required. Optional FD approval, suitable for potable water and food contact. Sizes: 2-10 (50-250mm) 200 psi CP (cold water pressure) (non-shock) pproved valves shall comply with the merican Standard for face-to-face dimensions (NSI 16.10) for Class 125 cast iron flanged gate valves. The dimensions and drilling of end flanges conform to the merican cast iron flange standard, Class 125 (NSI 16.1). Suitable eturn Valve Nominal Size Type ctuators C v Inches DN [mm] 2-way NPT Non-Spring VS 420 2½ VS VS VS VS VS VS SY Series K /08 - Subject to change. elimo ircontrols (US), Inc. Pressure rating 200 psig OG Media temp. range -22 F to 298 F (-30 C to 148 C) Close-off pressure F Maximum differential <200 psi pressure ( P) 9

11 K /08 - Subject to change. elimo ircontrols (US), Inc. 10

12 all Valve Product ange Overview VS/VSS all Valve Product ange 2...VS/VSS, 3...VS, 6...VS K /08 - Subject to change. elimo ircontrols (US), Inc. Valve Nominal Size Type Suitable ctuators C v Inches DN [mm] 2-way NPT 1 ½ 15 2VS 2 ½ 15 3VS 4 ½ 15 4VS 15 ½ 15 5VS 30 ¾ 20 9VS 51 ¾ VS VS VS 48 1¼ 32 2VS 84 1½ 40 9VS 177 1½ VS VS VS 503 2½ VS VS 15 ½ 15 5VSS 30 ¾ 20 9VSS VSS 48 1¼ 32 2VSS 84 1½ 40 9VSS VSS 503 2½ VSS 3-way NPT 4.8 ½ VS 11 ¾ VS VS 33 1¼ VS 49 1½ VS VS 2-ay Flanged VS 420 2½ VS VS VS VS VS VS LF Spring eturn LF Series NF Series F Series LF Series F Series NF F Series NF Non-Spring eturn LM Series NM Series M Series GM Series NM Series M Series GM Series LM NM Series M GM Series SY Series SY Series pplications ater-side control of air handling apparatus in ventilation and air-conditioning systems ater/steam control in heating systems Mode of Operation The control valve is operated by an electronic actuator that responds to a standard voltage for on/off control, by a proportional VDC/4 20 m, or 3-point control system. The actuator will then move the ball to the valve to the position dictated by the contol signal thus change the flow. Product Features Modified equal percentage of flow for 2, 3 and 6. Modified linear flow for 3. ctuator Specifications Control type M Manual override Electrical connection Valve Specifications Service Flow characteristic On/Off, Floating Point, Proportional, 2-10 VDC multi-function Technology (MFT) LM, NM, GM, M, SY, F 3 ft [1m] cable with ½ conduit fitting chilled or hot water, 60% glycol or steam modified equal percentage (2-way), modified linear (3-way) Sizes 1 to 10 Type of end fitting NPT (2 & 3 VS) flanged (6VS) Materials ody bronze (2 & 3VS), stainless steel (2VSS), cast iron (6VS) Stem stainless steel Seats PTFe Packing PTFE Pressure rating 600 psi Media temp range 2, 3VS -22 F to 280 F [-30 C to 138 C] 2VSS -22 F to 298 F [-30 C to 148 C] Maximum inlet pressure Steam 35 psi 2VS 50 psi 2VSS, 6VS 11

13 LF ctuators, On/Off Dimensions with 2-ay Valve Models LF24 US LF24-S US LF120 US LF120-S US w/built-in ux. Switch w/built-in ux. Switch Technical Data Control On/Off, Floating Power supply LF24(-S) US 24 VC ± 20% 50/60 Hz 24 VDC ± 10% LF120(-S) US 120 VC ± 10% 50/60 Hz Power consumption LF24(-S) US running 5 holding 2.5 LF120(-S) US running 5.5 holding 3.5 Transformer sizing LF24(-S) US 7 V, class 2 power source LF120(-S) US Electrical connection (-S models have 2 cables) ½ conduit connector 3 ft [1m], 18 G appliance cable Electrical protection 120V actuators double insulated Overload protection electronic throughout rotation ngle of rotation 95 Spring return direction reversible with C/CC mounting Position indication visual indicator 0 to 90 unning time <40 to 75 sec. (on-off) spring <25 F to 122 F [-20 C to 50 C] <60 F [-30 C] mbient temperature -22 F to 122 F [-30 C to 50 C] Housing NEM 2 gency listings UL 873, CS C22.2 No. 24 certified, CE Quality standard ISO 9001 Noise level max. 62 d() LF...-S US uxiliary switch 1 x SPDT, VC, UL Listed, adjustable 0 to 95 (double insulated) ated impulse voltage 800V (4kV for 120V model), Control pollution degree 3, Type of action 1. (1.. for -S models) Valve Nominal Size Dimensions (Inches) Valve ody COP Inches DN [mm] C D F 2VS 50 ½ VS 50 ½ VS 50 ½ VS 50 ½ VSS 1000 ½ Dimensions with 3-ay Valve Valve Nominal Size Dimensions (Inches) Valve ody COP Inches DN [mm] C D E F 315VS 75 ½ PGE11 K /08 - Subject to change. elimo ircontrols (US), Inc. 12

14 LF ctuators, On/Off iring Diagrams 1 Provide overload protection and disconnect as required. 2 CUTION Equipment damage! ctuators may be connected in parallel. Power consumption must be observed. 3 ctuator may also be powered by 24 VDC. 4 For end position indication, interlock control, fan startup, etc., LF24-S US and LF120-S US incorporates a built-in auxiliary switch: 1 x SPDT, VC, UL listed, adjustable 0 to Common 2 + Hot 3 LF24 US 2 On/Off wiring for 24 VC/DC LF-08 Meets culus or UL and CS requirements without the need of an electrical ground connection. NING Live Electrical Components! During installation, testing, servicing and troubleshooting of this product, it may be necessary to work with live electrical components. Have a qualified licensed electrician or other individual who has been properly trained in handling live electrical components perform these tasks. Failure to follow all electrical safety precautions when exposed to live electrical components could result in death or serious injury. On/Off wiring for 120 VC 048-UX uxiliary Switch K /08 - Subject to change. elimo ircontrols (US), Inc. 13

15 LF24-MFT US ctuators, Multi-Function Technology Dimensions with 2-ay Valve Models LF24-MFT US LF24-MFT-S US w/built-in ux. Switch Technical Data Control MFT Control signal 2 to 10 VDC (4-20m with 500 Ω resistor) Power consumption running 2.5 holding 1 Transformer sizing 5 V (class 2 power source) Electrical connection (-S models have 2 cables) ½ conduit connector 3 ft [1m], 18 G appliance cable Overload protection electronic throughout 0 to 95 rotation Input impedance 100 kω for 2 to 10 VDC (0.1 m) 500 Ω for 4 to 20m 750 Ω for PM 500 Ω for on/off and floating point Feedback 2 to 10 VDC, 0.5 m max ngle of rotation 95 Direction of rotation spring reversible with C/CC mounting motor reversible with built-in switch Position indication visual indicator unning time <40 to 75 sec. (on-off) 150 sec. independent of load (proportional) spring <25 F to 122 F [-20 C to 50 C] <60 F [-30 C] mbient temperature -22 F to 122 F [-30 C to 50 C] Housing NEM 2 gency listings UL 873, CS C22.2 No. 24 certified, CE Noise level max. 62 d() Quality standard ISO 9001 LF24-MFT-S US uxiliary switch 1 x SPDT, VC, UL Listed, adjustable 0 to 95 (double insulated) Valve Nominal Size Dimensions (Inches) Valve ody COP Inches DN [mm] C D F 2VS 50 ½ VS 50 ½ VS 50 ½ VS 50 ½ VSS 1000 ½ Dimensions with 3-ay Valve Valve Nominal Size Dimensions (Inches) Valve ody COP Inches DN [mm] C D E F 315VS 75 ½ K /08 - Subject to change. elimo ircontrols (US), Inc. 14

16 LF24-MFT US ctuators, Multi-Function Technology iring Diagrams 24 VC/DC Transformer CUTION Equipment damage! ctuators may be connected in parallel if not mechanically mounted to the same shaft. Power consumption and input impedance must be observed. Position ( ) Feedback VDC (+) a (1) Common (2) Hot (3) y input (5) u output 3 ctuators may also be powered by 24 VDC. CC C MFT 4 IN4004 or IN4007 diode (IN4007 supplied, elimo part number 40155). 5 Triac and can also be contact closures. 6 7 Control signal may be pulsed from either the Hot (Source) or Common (Sink) 24 VC line. Position feedback cannot be used with Triac sink controller. The actuators internal common reference is not compatible. On/Off control (C only) 7 Position Feedback VDC ( ) (+) 6 (1) Common (2) + Hot (3) y input (5) u output 041 The ZG Ω resistor converts the 4 to 20 m control signal to 2 to 10 VDC, up to 2 actuators may be connected in parallel. CC C MFT NING Live Electrical Components! During installation, testing, servicing and troubleshooting of this product, it may be necessary to work with live electrical components. Have a qualified licensed electrician or other individual who has been properly trained in handling live electrical components perform these tasks. Failure to follow all electrical safety precautions when exposed to live electrical components could result in death or serious injury. PM, triac source and sink 302 K /08 - Subject to change. elimo ircontrols (US), Inc. Floating Point control Propotional 2 to 10 or 4 to 20 m control signal

17 NF ctuators, On/Off Dimensions with 2-ay Valve Models NF24 US NF24-S US NF120 US NF120-S US w/built-in ux. Switch w/built-in ux. Switch Valve Nominal Size Dimensions (Inches) Valve ody COP Inches DN [mm] C D F 9VS 400 ¾ VS 200 ¾ Technical Data Control On/Off Power consumption NF24(-S) US running 5 holding 2.6 NF120(-S) US running 6 holding 3.5 Transformer sizing 10 V, class 2 power Electrical connection (-S model has 2 cables) ½ conduit connector 3 ft [1m], 18 G appliance cables Electrical protection 120 V actuators double insulated Overload protection electronic throughout 0 to 95 rotation ngle of rotation 95 Position indication visual indicator unning time control <75 sec. spring <60 sec. mbient temperature -22 F to 122 F [-30 C to 50 C] Housing NEM 2 / IP54 gency listings UL 873, CS C22.2 No. 24 certified, CE Noise level max. 45 d() NF...-S US uxiliary switch 1 x SPDT, VC, UL listed, adjustable 5 to 85 Dimensions with 3-ay Valve Valve Nominal Size Dimensions (Inches) Valve ody COP Inches DN [mm] C D E F 320VS 75 ¾ K /08 - Subject to change. elimo ircontrols (US), Inc. 16

18 NF ctuators, On/Off iring Diagrams 1 Provide overload protection and disconnect as required. 2 CUTION Equipment damage! ctuators may be connected in parallel. Power consumption must be observed. 3 ctuators may also be powered by 24 VDC. 4 For end position indication, interlock control, fan startup, etc., NF24-S US incorporates a built-in auxiliary switch: 1 x SPDT, VC, UL listed, adjustable 5 to Common 2 + Hot 3 NF24 US 2 On/Off iring for 24 VC/DC 194_NF 003-NF-08 Meets culus or UL and CS requirements without the need of an electrical ground connection. NING Live Electrical Components! During installation, testing, servicing and troubleshooting of this product, it may be necessary to work with live electrical components. Have a qualified licensed electrician or other individual who has been properly trained in handling live electrical components perform these tasks. Failure to follow all electrical safety precautions when exposed to live electrical components could result in death or serious injury. On/Off iring for 120 VC S1 NF120 US S2 S3 NC NO 5 to 85 NF -S US uxiliary Switch K /08 - Subject to change. elimo ircontrols (US), Inc. 17

19 NF ctuators, Multi-Function Technology Dimensions with 2-ay Valve Models NF24-MFT US Technical Data Control MFT Control signal 2 to 10 VDC, (4 to 20 m with 500 Ω resistor) Power supply 24 VC ± 20% 50/60 Hz 24 VDC ± 10% Power consumption running 6 holding 1.8 Transformer sizing 10 V, class 2 power Electrical connection ½ conduit connector 3 ft [1m], 18 G appliance cable Overload protection electronic throughout rotation Input impedance 100 kω for 2 to 10 VDC (0.1 m) 500 Ω for 4 to 20 m 1500 Ω for on/off and floating point Feedback output 2 to 10 VDC, 0.5 m max ngle of rotation 95 Direction of otation spring reversible with C/CC mounting motor reversible with built-in switch Position indication visual indicator, 0 to 95 unning time control 150 sec. constant spring <60 sec. mbient temperature -22 F to 122 F [-30 C to 50 C] Housing NEM 2 / IP54 gency listings UL 873 listed, CS C22.2 No. 24 certified, CE Noise level less than 45 d() Valve Nominal Size Dimensions (Inches) Valve ody COP Inches DN [mm] C D F 9VS 400 ¾ VS 200 ¾ Dimensions with 3-ay Valve Valve Nominal Size Dimensions (Inches) Valve ody COP Inches DN [mm] C D E F 320VS 75 ¾ K /08 - Subject to change. elimo ircontrols (US), Inc. 18

20 NF ctuators, Multi-Function Technology iring Diagrams to live electrical components could result in death or serious injury. 24 VC/DC Transformer CUTION Equipment damage! ctuators may be connected in parallel if not mechanically mounted to the same shaft. Power consumption and input impedance must be observed. Position ( ) Feedback VDC (+) a (1) Common (2) Hot (3) y input (5) u output 3 ctuators may also be powered by 24 VDC. 4 IN4004 or IN4007 diode (IN4007 supplied, elimo part number 40155). On/Off control CC C MFT 5 Triac and can also be contact closures. 6 7 Control signal may be pulsed from either the Hot (Source) or Common (Sink) 24 VC line. Position feedback cannot be used with Triac sink controller. The actuators internal common reference is not compatible. (C only) 7 Position Feedback VDC ( ) (+) 6 (1) Common (2) + Hot (3) y input (5) u output 041 The ZG Ω resistor converts the 4 to 20 m control signal to 2 to 10 VDC, up to 2 actuators may be connected in parallel. Meets culus or UL and CS requirements without the need of an electrical ground connection. NING Live Electrical Components! During installation, testing, servicing and troubleshooting of this product, it may be necessary to work with live electrical components. Have a qualified licensed electrician or other individual who has been properly trained in handling live electrical components perform these tasks. Failure to follow all electrical safety precautions when exposed to live electrical components could result in death or serious injury. PM, triac source and sink CC C MFT 302 K /08 - Subject to change. elimo ircontrols (US), Inc. Floating Point control Propotional 2 to 10 or 4 to 20 m control signal

21 F ctuators, On/Off Dimensions with 2-ay Valve Models F24 US F24-S US F120 US F120-S US w/built-in ux. Switches w/built-in ux. Switches Technical Data Control On/Off Power consumption F24(-S) US running 5 holding 1.5 F120(-S) US running 6 holding 2.3 Transformer sizing 10 V, class 2 power Electrical connection (-S model has 2 cables) ½ conduit connector 3 ft [1m], 18 G appliance cables Electrical protection 120 V actuators double insulated Overload protection electronic throughout 0 to 95 rotation ngle of rotation 95 Position indication visual indicator Manual override hex crank unning time control 150 sec. independent of load spring <20 sec. mbient temperature -22 F to 122 F [-30 C to 50 C] Housing NEM 2 / IP54 gency listings UL 873, CS C22.2 No. 24 certified, CE Noise level max. 45 d() F...-S US uxiliary switches * Dual Mounted ctuators 2 x SPDT, VC, UL listed, one switch is fixed at +5, one is adjustable 25 to 85 (double insulated) Valve Nominal Size Dimensions (Inches) Valve ody COP Inches DN [mm] C D F 224VS VS VS 200 1¼ *9VS 400 1½ *240VS 50 1½ *249VS VSS 1000 ¾ VSS VSS 400 1¼ *2VSS ¼ *9VSS ½ *249VSS Dimensions with 3-ay Valve Valve Nominal Size Dimensions (Inches) Valve ody COP Inches DN [mm] C D E F 325VS VS 75 1¼ VSS VSS 200 1¼ *340VS 75 1½ *350VS K /08 - Subject to change. elimo ircontrols (US), Inc. 20

22 F ctuators, On/Off iring Diagrams 1 Provide overload protection and disconnect as required. 2 CUTION Equipment damage! ctuators may be connected in parallel. Power consumption must be observed. 3 ctuators may also be powered by 24 VDC. 4 For end position indication, interlock control, fan startup, etc., F24-S US incorporates two built-in auxiliary switches: 2 x SPDT, VC, UL listed, one switch is fixed at +5, one is adjustable 25 to 85. to live electrical components could result in death or serious injury. 1 Common 2 + Hot 3 F24 US 2 On/Off iring for 24 VC/DC F-08 Meets culus or UL and CS requirements without the need of an electrical ground connection. NING Live Electrical Components! During installation, testing, servicing and troubleshooting of this product, it may be necessary to work with live electrical components. Have a qualified licensed electrician or other individual who has been properly trained in handling live electrical components perform these tasks. Failure to follow all electrical safety precautions when exposed to live electrical components could result in death or serious injury. On/Off iring for 120 VC 195-UX uxiliary Switches K /08 - Subject to change. elimo ircontrols (US), Inc.

23 F ctuators, Multi-Function Technology Dimensions with 2-ay Valve Models F24-MFT US F24-MFT-S US F24 w/built-in ux. Switches Technical Data Control MFT Control signal 2 to 10 VDC, (4 to 20 m with 500 Ω resistor) Ω (MFT95) Power supply 24 VC ± 20% 50/60 Hz 24 VDC ± 10% Power consumption running 6 holding 2.5 Transformer sizing 10 V, class 2 power Electrical connection (-S model has 2 cables) ½ conduit connector 3 ft [1m], 18 G appliance cable Overload protection electronic throughout rotation Input impedance 100 kω for 2 to 10 VDC (0.1 m) 500 Ω for 4 to 20 m 750 Ω for PM 1500 Ω for on/off and floating point Feedback output 2 to 10 VDC, 0.5 m max ngle of rotation 95 Direction of otation spring reversible with C/CC mounting motor reversible with built-in switch Position indication visual indicator Manual override hex crank unning time control 150 sec. independent of load spring <20 sec. mbient temperature -22 F to 122 F [-30 C to 50 C] Housing NEM 2 / IP54 gency listings UL 873, CS C22.2 No. 24 certified, CE Noise level max. 45 d() F24-MFT-S US uxiliary switches * Dual Mounted ctuators 2 x SPDT, VC, UL listed, one switch is fixed at +5, one is adjustable 25 to 85 (double insulated) Valve Nominal Size Dimensions (Inches) Valve ody COP Inches DN [mm] C D F 224VS VS VS 200 1¼ *9VS 400 1½ *240VS 50 1½ *249VS VSS 1000 ¾ VSS VSS ¼ *2VSS ¼ *9VSS ½ *249VSS Dimensions with 3-ay Valve Valve Nominal Size Dimensions (Inches) Valve ody COP Inches DN [mm] C D E F 325VS VS 75 1¼ *325VS *332VS 200 1¼ *340VS 75 1½ *350VS K /08 - Subject to change. elimo ircontrols (US), Inc. 22

24 F ctuators, Multi-Function Technology iring Diagrams to live electrical components could result in death or serious injury. 24 VC/DC Transformer CUTION Equipment damage! ctuators may be connected in parallel if not mechanically mounted to the same shaft. Power consumption and input impedance must be observed. Position ( ) Feedback VDC (+) a (1) Common (2) Hot (3) y input (5) u output 3 ctuators may also be powered by 24 VDC. 4 IN4004 or IN4007 diode (IN4007 supplied, elimo part number 40155). On/Off control CC C MFT 5 Triac and can also be contact closures. 6 7 Control signal may be pulsed from either the Hot (Source) or Common (Sink) 24 VC line. Position feedback cannot be used with Triac sink controller. The actuators internal common reference is not compatible. (C only) 7 Position Feedback VDC ( ) (+) 6 (1) Common (2) + Hot (3) y input (5) u output 041 The ZG Ω resistor converts the 4 to 20 m control signal to 2 to 10 VDC, up to 2 actuators may be connected in parallel. Meets culus or UL and CS requirements without the need of an electrical ground connection. NING Live Electrical Components! During installation, testing, servicing and troubleshooting of this product, it may be necessary to work with live electrical components. Have a qualified licensed electrician or other individual who has been properly trained in handling live electrical components perform these tasks. Failure to follow all electrical safety precautions when exposed to live electrical components could result in death or serious injury. PM, triac source and sink CC C MFT 302 K /08 - Subject to change. elimo ircontrols (US), Inc. Floating Point control Propotional 2 to 10 or 4 to 20 m control signal UXMFT uxiliary Switches

25 F ctuators, Multi-Function Technology Override INSTLLTION NOTES Provide overload protection and disconnect as required. ctuators and controller must have separate transformers. Consult controller instruction data for more detailed information. esistor value depends on the type of controller and the number of actuators. No resistor is used for one actuator. Honeywell resistor kits may also be used. To reverse control rotation, use the reversing switch. Switch Switch Damper Position Damper Open Damper Closed The direction of rotation switch is set so that the fail safe position and the position of the damper is closed with no signal at wire. 22 Low Limit Control 22 Series 90 Controller 135 Controller Series 90 low limit control 135 for 0 to 50% control 280 for 0 to 100% control lk (1) Common ed (2) + Hot ht (3) 24 ht (4) ht (5) lk (1) Common ed (2) + Hot ht (3) 24 ht (4) ht (5) lk (1) Common ed (2) + Hot ht (3) 24 ht (4) ht (5) High Limit Control 22 Series 90 Controller iring Multiple ctuators to a Series 90 Controller lk (1) Common ed (2) + Hot Series 90 high limit control Shunting esistor 24 Series 90 Controller No. of actuators esistance esistor Kit No. ZG-03 To other actuators lk (1) Common ed (2) + Hot ht (3) 24 ht (4) ht (5) ht (3) 25 ht (4) ht (5) lk (1) Common ed (2) + Hot ht (3) 25 ht (4) ht (5) iring Multiple ctuators to a Series 90 Controller using a Minimum Position Potentiometer Series 90 Controller 22 Shunting esistor H205 Changeover Controller Occupied Contact To other actuators S963 Minimum Position Potentiometer lk (1) Common ed (2) + Hot 25 ht (3) ht (4) ht (5) lk (1) Common ed (2) + Hot ht (3) 25 ht (4) ht (5) Typical wiring diagrams for multiple actuators used with the 973, 7100 and T775 controllers H205 Changeover Controller 22 Shunting esistor 973, 7100 Controller No. of actuators esistance esistor Kit No. ZG Shunting esistor 22 Y 973, 7100 T775 Q209 Minimum Position Potentiometer To other actuators To other actuators lk (1) Common ed (2) + Hot ht (3) 25 ht (4) ht (5) Occupied Contact Honeywell T675 Morning armup lk (1) Common ed (2) + Hot ht (3) 25 ht (4) ht (5) Used with the 973 and 7100 controllers Honeywell T675 Morning armup Honeywell Q209 Minimum Position Potentiometer lk (1) Common ed (2) + Hot ht (3) 25 ht (4) ht (5) lk (1) Common ed (2) + Hot 020 ht (3) 25 ht (4) ht (5) K /08 - Subject to change. elimo ircontrols (US), Inc. 24

26 LM()X24-3X1 ctuators, On/Off, Floating Point Dimensions with 2-ay Valve PGE7 H2 H1 C F K /08 - Subject to change. elimo ircontrols (US), Inc. Models LM24-3X1 LMX24-3X1 Technical Data Control On/Off, Floating Point Power supply 24 VC ± 20% 50/60 Hz 24 VDC ± 10% Power consumption running 1.5 holding 0.2 Transformer sizing 3 V (class 2 power source) Electrical connection LM24-3X1 ½ conduit connector 3 ft, 18 G plenum rated cables Overload protection electronic throughout 0 to 95 rotation Input Impedance 600 Ω ngle of rotation 95 Torque 45 in-lb [5 Nm] Direction of rotation reversible with switch Position indication reflective visual indicator (snap-on) Manual override external push button unning time 95 seconds, constant independent of load Humidity 5 to 95% H non-condensing (EN ) mbient temperature -22 F to 122 F [-30 C to 50 C] Storage temperature -40 F to 176 F [-40 C to 80 C] Housing NEM type 2/IP54 Housing material UL94-5V gency listings culus acc. to UL /-2-14, CN/CS C22.2 No. 24 certified, CE acc. to 73//EEC Noise level <35 db() Servicing maintenance free Quality standard ISO 9001 D Valve Nominal Size Dimensions (Inches) Valve ody COP Inches DN [mm] C D F H1 H2 2VS 50 ½ VS 50 ½ VS 50 ½ VS 50 ½ Dimensions with 3-ay Valve C D Valve Nominal Dimensions (Inches) Size DN Valve ody COP Inches C D E F H1 H2 [mm] 315VS 75 ½ H1 H2 E F PGE11 25

27 LM()X24-3X1 ctuators, On/Off, Floating Point iring Diagrams Provide overload protection and disconnect as required. 3 ctuators may also be powered by 24 VDC. Meets culus or UL and CS requirements without the need of an electrical ground connection. NING Live Electrical Components! During installation, testing, servicing and troubleshooting of this product, it may be necessary to work with live electrical components. Have a qualified licensed electrician or other individual who has been properly trained in handling live electrical components perform these tasks. Failure to follow all electrical safety precautions when exposed to live electrical components could result in death or serious injury. On/Off control Floating Point or On/Off control Piping The valve should be mounted in a weather-protected area in a location that is within the ambient limits of the actuator. llow sufficient room for valve with actuator and for service. llow 6 for cover removal and 12 for complete actuator removal. The assembly can be mounted with the actuator vertical or horizontal in relation to the pipe. The actuators should never be mounted underneath the valve, as condensation can build up and result in a failure of the actuators. Do not reverse flow direction. K /08 - Subject to change. elimo ircontrols (US), Inc. 26

28 LMX24-MFTX1 ctuators, Multi-Function Technology Dimensions with 2-ay Valve PGE7 H2 H1 C F K /08 - Subject to change. elimo ircontrols (US), Inc. Models LMX24-MFTX1 Technical Data Power supply 24 VC ± 20% 50/60 Hz 24 VDC ± 10% Power consumption 2 Transformer sizing 3.5 V (class 2 power source) Electrical connection 3 ft [1m] 10 ft [3m] 16 ft [5m] 18 G plenum rated cable ½ conduit connector Overload protection electronic throughout 0 to 95 rotation Input Impedance 100k Ω for 2 to 10 VDC (0.1 m) 500 Ω for 4 to 20 m 750 Ω for PM 1500 Ω for On/Off and Floating Point Feedback 2 to 10 VDC, 0.5 m max VDC variable ngle of rotation 95 Torque 45 in-lb [5 Nm] Direction of rotation reversible with switch Position indication reflective visual indicator (snap-on) Manual override external push button unning time 150 seconds (default) Variable (35 to 150 secs) Humidity 5 to 95% H non-condensing (EN ) mbient temperature -22 F to 122 F [-30 C to 50 C] Storage temperature -40 F to 176 F [-40 C to 80 C] Housing NEM type 2/IP54 Housing material UL94-5V gency listings culus acc. to UL /-2-14, CN/CS E , CS C22.2 No , CE acc. to 89/336/EEC Noise level <35 db() Servicing maintenance free Quality standard ISO 9001 D Valve Nominal Dimensions (Inches) Size Valve ody COP Inches DN [mm] C D F H1 H2 2VS 50 ½ VS 50 ½ VS 50 ½ VS 50 ½ Dimensions with 3-ay Valve C D Valve Nominal Size Dimensions (Inches) Valve ody COP Inches DN [mm] C D E F H1 H2 315VS 75 ½ H1 H2 E F PGE11 27

29 LMX24-MFTX1 ctuators, Multi-Function Technology iring Diagrams 1 Provide overload protection and disconnect as required. 3 ctuators may also be powered by 24 VDC. 4 5 Position feedback cannot be used with Triac sink controller. The actuator internal common reference is not compatible. Control signal may be pulsed from either the Hot (source) or the Common (sink) 24 VC line. 6 ZG-01 may be used. 7 8 Contact closures & also can be triacs. & should both be closed for triac source and open for triac sink. For triac sink the common connection from the actuator must be connected to the hot connection of the controller. On/Off control 1 24 VC/DC Transformer 1 3 a Position ( ) Feedback VDC (+) 2 2 lk (1) Common red (2) Hot wht (3) y input org (5) u output MFT lk (1) Common red (2) Hot to 10 VDC Feedback Signal a 7 4 wht (3) y 1 input 8 Pnk (4) y 2 input org (5) u output 2 to 10V MFT Floating Point 1 3 Ω 500Ω 1/4 watt Control Signal 4 to 20 m or 2 to 10 VDC ( ) (+) 6 2 lk (1) Common red (2) + Hot wht (3) y 1 input, 2 to 10V org (5) u output, 2 to 10V 399 MFT VDC/4-20 m PM 1 (C only) 2 Position Feedback VDC ( ) (+) 5 lk (1) Common red (2) + Hot wht (3) y input org (5) u output MFT 399 K /08 - Subject to change. elimo ircontrols (US), Inc. 28

30 NM()X24-3X1 ctuators, On/Off, Floating Point Dimensions with 2-ay Valve PGE7 H2 H1 C F K /08 - Subject to change. elimo ircontrols (US), Inc. Models NM24-3X1 NMX24-3X1 Technical Data Control On/Off, Floating Point Power supply 24 VC ± 20% 50/60 Hz 24 VDC ± 10% Power consumption running 2.0 holding 0.2 Transformer sizing 4 V (class 2 power source) Electrical connection NM24-3X1 3 ft, 18 G plenum rated cable ½ conduit connector Overload protection electronic throughout 0 to 95 rotation Input Impedance 600 Ω ngle of rotation max 95, adjustable with mechanical stop Torque 90 in-lb [10 Nm] Direction of rotation reversible with switch =CC with decreasing control signal (10-2V) =C with decreasing control signal (10-2V) Position indication reflective visual indicator (snap-on) Manual override external push button unning time 95 seconds, constant independent of load Humidity 5 to 95% H non-condensing (EN ) mbient temperature -22 F to 122 F [-30 C to 50 C] Storage temperature -40 F to 176 F [-40 C to 80 C] Housing NEM type 2/IP54 Housing material UL94-5V gency listings culus acc. to UL /-2-14, CN/CS C22.2 No. 24 certified, CE acc. to 73//EEC Noise level <45 db() Servicing maintenance free Quality standard ISO 9001 D Valve Nominal Dimensions (Inches) Size Valve ody COP Inches DN [mm] C D F H1 H2 9VS 400 ¾ VS 400 ¾ VSS 1000 ½ VSS 1000 ¾ Dimensions with 3-ay Valve C D Valve Nominal Dimensions (Inches) Size Valve ody COP Inches DN [mm] C D E F H1 H2 320VS 75 ¾ VS H1 H2 E F PGE11 29

31 NM()X24-3X1 ctuators, On/Off, Floating Point iring Diagrams Provide overload protection and disconnect as required. 3 ctuators may also be powered by 24 VDC. Meets culus or UL and CS requirements without the need of an electrical ground connection. NING Live Electrical Components! During installation, testing, servicing and troubleshooting of this product, it may be necessary to work with live electrical components. Have a qualified licensed electrician or other individual who has been properly trained in handling live electrical components perform these tasks. Failure to follow all electrical safety precautions when exposed to live electrical components could result in death or serious injury. On/Off control Floating Point or On/Off control Piping The valve should be mounted in a weather-protected area in a location that is within the ambient limits of the actuator. llow sufficient room for valve with actuator and for service. llow 6 for cover removal and 12 for complete actuator removal. The assembly can be mounted with the actuator vertical or horizontal in relation to the pipe. The actuators should never be mounted underneath the valve, as condensation can build up and result in a failure of the actuators. Do not reverse flow direction. K /08 - Subject to change. elimo ircontrols (US), Inc. 30

32 NMX24-MFTX1 ctuators, Multi-Function Technology Dimensions with 2-ay Valve PGE7 H2 H1 C F Models NMX24-MFTX1 K /08 - Subject to change. elimo ircontrols (US), Inc. Technical Data Power supply 24 VC ± 20% 50/60 Hz 24 VDC ± 10% Power consumption 3.5 (1.25 ) Transformer sizing 5.5 V (class 2 power source) Electrical connection 3 ft [1m] 10 ft [3m] 16 ft [5m] 18 G plenum rated cable ½ conduit connector Overload protection electronic throughout 0 to 95 rotation Input Impedance 100k Ω for 2 to 10 VDC (0.1 m) 500 Ω for 4 to 20 m 750 Ω for PM 1500 Ω for On/Off and Floating Point Feedback 2 to 10 VDC, 0.5 m max VDC variable ngle of rotation max 95, adjust. with mechanical stop electronically variable Torque 90 in-lb [10 Nm] Direction of rotation reversible with switch Position indication reflective visual indicator (snap-on) Manual override external push button unning time 150 seconds (default) Variable (45 to 170 secs) Humidity 5 to 95% H non-condensing (EN ) mbient temperature -22 F to 122 F [-30 C to 50 C] Storage temperature -40 F to 176 F [-40 C to 80 C] Housing NEM type 2/IP54 Housing material UL94-5V gency listings culus acc. to UL /-2-14, CN/CS E , CS C22.2 No , CE acc. to 89/336/EEC Noise level <45 db() Servicing maintenance free Quality standard ISO 9001 D Valve Nominal Dimensions (Inches) Size Valve ody COP Inches DN [mm] C D F H1 H2 9VS 400 ¾ VS 400 ¾ VSS 1000 ½ VSS 1000 ¾ Dimensions with 3-ay Valve C D Valve Nominal Dimensions (Inches) Size Valve ody COP Inches DN [mm] C D E F H1 H2 320VS 75 ¾ VS H1 H2 E F PGE11 31

33 NMX24-MFTX1 ctuators, Multi-Function Technology iring Diagrams 1 Provide overload protection and disconnect as required. 3 ctuators may also be powered by 24 VDC. 4 5 Position feedback cannot be used with Triac sink controller. The actuator internal common reference is not compatible. Control signal may be pulsed from either the Hot (source) or the Common (sink) 24 VC line. 6 ZG-01 may be used. 7 8 Contact closures & also can be triacs. & should both be closed for triac source and open for triac sink. For triac sink the common connection from the actuator must be connected to the hot connection of the controller. On/Off control 1 24 VC/DC Transformer 1 3 a Position ( ) Feedback VDC (+) 2 2 lk (1) Common red (2) Hot wht (3) y input org (5) u output MFT lk (1) Common red (2) Hot to 10 VDC Feedback Signal a 7 4 wht (3) y 1 input 8 Pnk (4) y 2 input org (5) u output 2 to 10V MFT Floating Point 1 3 Ω 500Ω 1/4 watt Control Signal 4 to 20 m or 2 to 10 VDC ( ) (+) 6 2 lk (1) Common red (2) + Hot wht (3) y 1 input, 2 to 10V org (5) u output, 2 to 10V 399 MFT VDC/4-20 m PM 1 (C only) 2 Position Feedback VDC ( ) (+) 5 lk (1) Common red (2) + Hot wht (3) y input org (5) u output MFT 399 K /08 - Subject to change. elimo ircontrols (US), Inc. 32

34 M()X24-3X1 ctuators, On/Off, Floating Point Dimensions with 2-ay Valve PGE7 H2 H1 C F K /08 - Subject to change. elimo ircontrols (US), Inc. Models M24-3X1 MX24-3X1 Technical Data Control On/Off, Floating Point Power supply 24 VC ± 20% 50/60 Hz 24 VDC ± 10% Power consumption running 2.5 holding 0.2 Transformer sizing 5.5 V (class 2 power source) Electrical connection M24-3X1 ½ conduit connector 3 ft, 18 G plenum rated cable Overload protection electronic throughout 0 to 95 rotation Input Impedance 600 Ω ngle of rotation max 95, adjustable with mechanical stop Torque 180 in-lb [20 Nm] Direction of rotation reversible with switch Position indication reflective visual indicator (snap-on) Manual override external push button unning time 95 seconds, constant independent of load Humidity 5 to 95% H non-condensing (EN ) mbient temperature -22 F to 122 F [-30 C to 50 C] Storage temperature -40 F to 176 F [-40 C to 80 C] Housing NEM type 2/IP54 Housing material UL94-5V gency listings culus acc. to UL /-2-14, CN/CS C22.2 No. 24 certified, CE acc. to 73//EEC Noise level <45 db() Servicing maintenance free Quality standard ISO 9001 D Valve Nominal Dimensions (Inches) Size Valve ody COP Inches DN [mm] C D F H1 H2 224VS VS VS 400 1¼ VSS VSS ¼ Dimensions with 3-ay Valve C D Valve Nominal Dimensions (Inches) Size Valve ody COP Inches DN [mm] C D E F H1 H2 320VS 75 ¾ VS VS 75 1¼ H1 H2 E F PGE11 33

35 M()X24-3X1 ctuators, On/Off, Floating Point iring Diagrams Provide overload protection and disconnect as required. 2 CUTION Equipment damage! ctuators may be connected in parallel. Power consumption and input impedance must be observed. 3 ctuators may also be powered by 24 VDC. 5 Only connect common to neg. ( ) leg of control circuits. On/Off control Meets culus or UL and CS requirements without the need of an electrical ground connection NING Live Electrical Components! During installation, testing, servicing and troubleshooting of this product, it may be necessary to work with live electrical components. Have a qualified licensed electrician or other individual who has been properly trained in handling live electrical components perform these tasks. Failure to follow all electrical safety precautions when exposed to live electrical components could result in death or serious injury. Floating Point or On/Off control Piping The valve should be mounted in a weather-protected area in a location that is within the ambient limits of the actuator. llow sufficient room for valve with actuator and for service. llow 6 for cover removal and 12 for complete actuator removal. The assembly can be mounted with the actuator vertical or horizontal in relation to the pipe. The actuators should never be mounted underneath the valve, as condensation can build up and result in a failure of the actuators. Do not reverse flow direction. K /08 - Subject to change. elimo ircontrols (US), Inc. 34

36 MX24-MFTX1 ctuators, Multi-Function Technology Dimensions with 2-ay Valve PGE7 H2 H1 C F K /08 - Subject to change. elimo ircontrols (US), Inc. Models MX24-MFT MX24-MFT95 Technical Data Power supply 24 VC ± 20% 50/60 Hz 24 VDC ± 10% Power consumption 4 (1.25 ) Transformer sizing 6 V (class 2 power source) Electrical connection 3 ft [1m] 10 ft [3m] 16 ft [5m] 18 G plenum rated cable ½ conduit connector Overload protection electronic throughout 0 to 95 rotation Input Impedance 100 kω for 2 to 10 VDC (0.1 m) 500 Ω for 4 to 20 m 750 Ω for PM 1500 Ω for On/Off and Floating Point Feedback 2 to 10 VDC, 0.5 m max VDC variable ngle of rotation max 95, adjust. with mechanical stop electronically variable Torque 180 in-lb [20 Nm] Direction of rotation reversible with switch Position indication reflective visual indicator (snap-on) Manual override external push button unning time 150 seconds (default) Variable (90 to 350 secs) Humidity 5 to 95% H non-condensing (EN ) mbient temperature -22 F to 122 F [-30 C to 50 C] Storage temperature -40 F to 176 F [-40 C to 80 C] Housing NEM type 2/IP54 Housing material UL94-5V gency listings culus acc. to UL /-2-14, CN/CS E , CS C22.2 No , CE acc. to 89/336/EEC Noise level <45 db() Servicing maintenance free Quality standard ISO 9001 D Valve Nominal Dimensions (Inches) Size Valve ody COP Inches DN [mm] C D F H1 H2 224VS VS VS 400 1¼ VSS VSS ¼ Dimensions with 3-ay Valve C D Valve Nominal Dimensions (Inches) Size Valve ody COP Inches DN [mm] C D E F H1 H2 320VS 75 ¾ VS VS 75 1¼ H1 H2 E F PGE11 35

37 MX24-MFTX1 ctuators, Multi-Function Technology iring Diagrams 1 Provide overload protection and disconnect as required. 3 ctuators may also be powered by 24 VDC. 4 5 Position feedback cannot be used with Triac sink controller. The actuator internal common reference is not compatible. Control signal may be pulsed from either the Hot (source) or the Common (sink) 24 VC line. 6 ZG-01 may be used. 7 8 Contact closures & also can be triacs. & should both be closed for triac source and open for triac sink. For triac sink the common connection from the actuator must be connected to the hot connection of the controller. On/Off control 1 24 VC/DC Transformer 1 3 a Position ( ) Feedback VDC (+) 2 2 lk (1) Common red (2) Hot wht (3) y input org (5) u output MFT lk (1) Common red (2) Hot to 10 VDC Feedback Signal a 7 4 wht (3) y 1 input 8 Pnk (4) y 2 input org (5) u output 2 to 10V MFT Floating Point 1 3 Ω 500Ω 1/4 watt Control Signal 4 to 20 m or 2 to 10 VDC ( ) (+) 6 2 lk (1) Common red (2) + Hot wht (3) y 1 input, 2 to 10V org (5) u output, 2 to 10V 399 MFT VDC/4-20 m PM 1 (C only) 2 Position Feedback VDC ( ) (+) 5 lk (1) Common red (2) + Hot wht (3) y input org (5) u output MFT 399 K /08 - Subject to change. elimo ircontrols (US), Inc. 36

38 MX24-MFTX1 ctuators, Multi-Function Technology K /08 - Subject to change. elimo ircontrols (US), Inc Override INSTLLTION NOTES Provide overload protection and disconnect as required. ctuators and controller must have separate transformers. Consult controller instruction data for more detailed information. esistor value depends on the type of controller and the number of actuators. No resistor is used for one actuator. Honeywell resistor kits may also be used. To reverse control rotation, use the reversing switch. Switch Switch Damper Position Damper Open Damper Closed The direction of rotation switch is set so that the fail safe position and the position of the damper is closed with no signal at wire. 22 Low Limit Control 22 Series 90 Controller 135 Controller Series 90 low limit control 135 for 0 to 50% control 280 for 0 to 100% control lk (1) Common ed (2) + Hot ht (3) 24 ht (4) ht (5) lk (1) Common ed (2) + Hot ht (3) 24 ht (4) ht (5) lk (1) Common ed (2) + Hot ht (3) 24 ht (4) ht (5) High Limit Control 22 Series 90 Controller iring Multiple ctuators to a Series 90 Controller lk (1) Common ed (2) + Hot Series 90 high limit control Shunting esistor 24 Series 90 Controller No. of actuators esistance esistor Kit No. ZG-03 To other actuators lk (1) Common ed (2) + Hot ht (3) 24 ht (4) ht (5) ht (3) 25 ht (4) ht (5) lk (1) Common ed (2) + Hot ht (3) 25 ht (4) ht (5) iring Multiple ctuators to a Series 90 Controller using a Minimum Position Potentiometer Series 90 Controller 22 Shunting esistor H205 Changeover Controller Occupied Contact To other actuators S963 Minimum Position Potentiometer lk (1) Common ed (2) + Hot 25 ht (3) ht (4) ht (5) lk (1) Common ed (2) + Hot ht (3) 25 ht (4) ht (5) Typical wiring diagrams for multiple actuators used with the 973, 7100 and T775 controllers H205 Changeover Controller 22 Shunting esistor 973, 7100 Controller No. of actuators esistance esistor Kit No. ZG Shunting esistor 22 Y 973, 7100 T775 Q209 Minimum Position Potentiometer To other actuators To other actuators lk (1) Common ed (2) + Hot ht (3) 25 ht (4) ht (5) Occupied Contact Honeywell T675 Morning armup lk (1) Common ed (2) + Hot ht (3) 25 ht (4) ht (5) Used with the 973 and 7100 controllers Honeywell T675 Morning armup Honeywell Q209 Minimum Position Potentiometer lk (1) Common ed (2) + Hot ht (3) 25 ht (4) ht (5) lk (1) Common ed (2) + Hot 020 ht (3) 25 ht (4) ht (5) 37

39 GM24-3X1 ctuators, On/Off, Floating Point Dimensions with 2-ay Valve PGE7 H2 H1 C F Models GM24-3X1 2xGM24-3X1 Technical Data Control On/Off, Floating Point Power supply 24 VC ± 20% 50/60 Hz 24 VDC ± 10% Power consumption running 4 holding 2 Transformer sizing 6 V (Class 2 power source) Electrical connection 3 ft [1m] 18 G plenum rated cable ½ conduit connector Overload protection electronic throughout stroke ngle of rotation 95 Direction of rotation reversible with switch Position indication reflective visual indicator (snap-on) unning time 150 seconds, constant independent of load Humidity 5 to 95% H non-condensing mbient temperature -22 F to 122 F [-30 C to 50 C] Housing NEM 2/IP54 with cable entry down Housing material UL94-5V (flammability rating) gency listings culus acc. to UL /-2-14, CN/CS E , CS C22.2 No , CE acc. to 89/336/EEC Noise level <45 d() Quality standard ISO 9001 D Valve Nominal Dimensions (Inches) Size Valve ody COP Inches DN [mm] C D F H1 H2 9VS 400 1½ VS VSS ½ VSS Dimensions with 3-ay Valve C D Valve Nominal Dimensions (Inches) Size Valve ody COP Inches DN [mm] C D E F H1 H2 340VS 75 1½ VS H1 H2 E F PGE11 K /08 - Subject to change. elimo ircontrols (US), Inc. 38

40 GM24-3X1 ctuators, On/Off, Floating Point Dimensions with 2xGM... and 2-ay Valve iring Diagrams H2 PGE7 1 Provide overload protection and disconnect as required. 2 ctuators may be connected in parallel if not mechanically mounted to the same shaft. Power consumption and input impedance must be observed. 3 ctuators may also be powered by 24 VDC. H1 C F Position feedback cannot be used with Triac sink controller. The actuator internal common reference is not compatible. Control signal may be pulsed from either the Hot (source) or the Common (sink) 24 VC line. Contact closures & also can be triacs. & should both be closed for triac source and open for triac sink. For triac sink the common connection from the actuator must be connected to the hot connection of the controller. K /08 - Subject to change. elimo ircontrols (US), Inc. D Valve Nominal Dimensions (Inches) Size Valve ody COP Inches DN [mm] C D F H1* H2* 240VS 400 1½ VS VS 100 2½ VS VSS VSS 200 2½ *Handles not available on spring return series or dual mounted actuators Dimensions with 2xGM... and 3-ay Valve C D Valve Nominal Dimensions (Inches) Size Valve ody COP Inches DN [mm] C D E F H1* H2* 350VS *Handles not available on spring return series or dual mounted actuators H1 H2 E F PGE11 On/Off control 1 Floating Point Piping 3 24 VC/DC Transformer 1 3 a Position ( ) Feedback VDC (+) 5 2 to 10 VDC Feedback Signal a lk (1) Common red (2) Hot wht (3) y input org (5) u output MFT lk (1) Common red (2) Hot + wht (3) y 1 input Pnk (4) y 2 input org (5) u output 2 to 10V MFT The valve should be mounted in a weather-protected area in a location that is within the ambient limits of the actuator. llow sufficient room for valve with actuator and for service. llow 6 for cover removal and 12 for complete actuator removal. The assembly can be mounted with the actuator vertical or horizontal in relation to the pipe. The actuators should never be mounted underneath the valve, as condensation can build up and result in a failure of the actuators. Do not reverse flow direction

41 GMX24-MFTX1 ctuators, Multi-Function Technology Dimensions with 2-ay Valve PGE7 H2 H1 C F Models GMX24-MFTX1 *2xGMX24-MFTX1 GMX24-MFT95 Technical Data Control On/Off, Floating Point, 2 to 10 VDC Power supply 24 VC ± 20% 50/60 Hz 24 VDC ± 10% Power consumption running 4.5 holding 3 Transformer sizing 7 V (Class 2 power source) Electrical connection 3 ft [1m] 18 G plenum rated cable ½ conduit connector Overload protection electronic throughout stroke Input impedance 100k Ω for 2 to 10 VDC (0.1 m) 500 Ω for 4 to 20 m 750 Ω for PM 1500 Ω for On/Off and Floating Point Feedback 2 to 10 VDC, 0.5 m max VDC variable ngle of rotation 95 Direction of rotation reversible with switch Position indication reflective visual indicator (snap-on) unning time 150 seconds, constant independent of load Humidity 5 to 95% H non-condensing mbient temperature -22 F to 122 F [-30 C to 50 C] Housing NEM 2/IP54 with cable entry down Housing material UL94-5V (flammability rating) gency listings culus acc. to UL /-2-14, CN/CS E , CS C22.2 No , CE acc. to 89/336/EEC Noise level <45 d() Quality standard ISO 9001 D Valve Nominal Dimensions (Inches) Size Valve ody COP Inches DN [mm] C D F H1 H2 9VS 400 1½ VS VSS ½ VSS Dimensions with 3-ay Valve C D Valve Nominal Dimensions (Inches) Size Valve ody COP Inches DN [mm] C D E F H1 H2 340VS 75 1½ VS H1 H2 E F PGE11 K /08 - Subject to change. elimo ircontrols (US), Inc. 40