Technical Documentation Pressure Independent Characterized Control Valves (PICCV) Patented Effective December 2007

Transcription

1 Technical Documentation Pressure Independent Characterized Control Valves (PICCV) Patented Effective December 2007 Belimo Project: 1100 Peachtree, Atlanta, Georgia

2 Control Valve Product Range Electronic Pressure Independent Characterized Control Valves U.S. Patent Electronic Characterized Control Valves U.S. Patent Electronic Zone Valves PICCV CCV PICCV Service: Flow Rate: Material: Control: Two-way 1/2 to 2 Chilled/Hot Water, 60% glycol GPM Brass Body Brass/Stainless Trim Floating Multi-Function Technology Spring Return or Non-Spring Return Typical Application Air Handling Units: Heating Coils Cooling Coils Unit Ventilators VAV Box Re-heat Coils Heat Pumps B2 Series B3 Series B6 Series Two-way Three-way Mixing/Diverting Two-way Flanged 1/2 to 3 Service: Chilled/Hot Water, 60% glycol C v Range: Material: Stainless Trim or Brass Trim Control: On/Off, Floating, 2-10 VDC Multi-Function Technology Spring Return or Non-Spring Return Typical Application Air Handling Units: Heating Coils Cooling Coils Fan Coil Units: Heating Coils Cooling Coils Unit Ventilators VAV Box Re-heat Coils Bypass Loops ZONE2 N Series Two-way NPT ZONE2 S Series Two-way Sweat ZONE3 N Series Three-way Diverting NPT ZONE3 S Series Three-way Diverting Sweat Service: Chilled/Hot Water, 50% glycol C v Range: Material: Brass Body Control: On/Off Spring Return Typical Application Fan Coil Units: 1/2 to 1 Baseboard Radiation Heating Coils Cooling Coils For detailed information and submittal data, see Technical Documentation at or on CD-ROM. 2

3 Control Valve Product Range Electronic Globe Valves Electronic Butterfly Valves Electronic Ball Valves VS Series G2 (S) Two-way Screwed Series Bronze or Stainless Trim G6 C (S) Two-way Flanged ANSI 125 Series Bronze or Stainless Trim G6 (S) Two-way Flanged ANSI 125 Series Bronze or Stainless Trim G6 (S)-250 Two-way Flanged ANSI 250 Series Bronze or Stainless Trim G3 (D) Three-way Screwed Series Bronze Trim G7 D (S) Three-way Flanged Series ANSI 125 Bronze or Stainless Trim G7 D (S)-250 Three-way Flanged Series ANSI 250 Bronze or Stainless Trim Three-way Valves available in Mixing or Diverting Service: C v Range: Material: Control: 1/2 to 6 Chilled/Hot Water, 60% Glycol, Steam (Two-way) (Three-way Mix.) (Three-way Div.) Stainless Steel Stem, Bronze Trim or Stainless Trim On/Off, Floating, 2-10 VDC Multi-Function Technology Spring Return or Non-Spring Return Typical Application Air Handling Units: Heating Coils Cooling Coils Fan Coil Units: Heating Coils Cooling Coils Unit Ventilators VAV Box Re-heat Coils Bypass Loops F6 Series (HS,HSU) F7 Series (HS,HSU) Two-way Three-way Mixing/Diverting F6 SHP Two-way ANSI 150/300 Series F7 SHP Three-way ANSI 150/300 Series Mixing/Diverting Typical Application Chiller and Cooling Tower Isolation Change-over Systems Large Air Handler Coil Control Bypass Control Applications B2 VS Series B3 VS Series B2 VSS Series B6 VS Series 2 to 30 1/2 to 10 Service: Chilled/Hot Water, 50% Glycol C v Range: ,426 Material: Stainless Shaft Stainless Disc Cast Iron, Full Lug Body EPDM Liner Control: On/Off, Floating, 2-10 VDC On/Off, Floating 2-10 VDC, 1-5 VDC, 4-20mA (NEMA 4 Actuator) Multi-Function Technology Spring Return or Non-Spring Return Two-way Screwed Stainless Steel Trim Three-way Mixing/ Diverting Screwed Stainless Steel Trim Two-way Screwed Stainless Steel Body and Trim Two-way Flanged Stainless Steel Trim Service: Chilled/Hot Water, 50% Glycol, Steam C v Range: 1 to 12,400 Material: Bronze or Stainless Body Stainless Steel Trim RPTFE Seats Control: On/Off, Floating, 2-10 VDC On/Off, Floating 2-10 VDC, 1-5 VDC, 4-20mA (NEMA 4 Actuator) Multi-Function Technology Spring Return or Non-Spring Return Typical Application Unit Ventilators Humidifiers Heating and Cooling Coils For detailed information and submittal data, see Technical Documentation at or on CD-ROM. Call Customer Service to discuss your application. 3

4 Valve/Actuator Selection At A Glance Base product nomenclature PICCV PT + LRX24-MFT VALVE ACTUATOR PICCV PT LRX24 - MFT VALVE SIZES GPM Ex: 003 = 3.0 GPM 24 VAC/DC Power* Valve Designation Sizes PICCV 15 1/2 20 3/ / /2 Non-Spring Return Actuator LR AR Rotary DESIGNATOR MFT DESCRIPTION Multi-Function Technology (MFT) 2 10 VDC Control or Selectable (See MFT chart opposite) TYPE OF VALVE 50 2 PRESSURE INDEPENDENT CHARACTERIZED CONTROL VALVE (PICCV) PICCV 2-way Chrome Plated Brass Ball & Brass Stem Spring Return Actuator TF LF AF Rotary -3 Floating control Description PT with P/T ports to measure delta P to verify the flow rate without P/T ports 4

5 Valve/Actuator Selection At A Glance Specify upon ordering P NO+AHU MFT CONFIGURATION SET-UP TAGGING P NO AHU SET UP* Non-Spring Models NO = Normally Open NC = Normally Closed Spring Return Models NO/FO = Normally Open/Fail Open NO/FC = Normally Open/Fail Closed NC/FO = Normally Closed/Fail Open NC/FC = Normally Closed/Fail Closed *Refers to valve port inlet to outlet, per flow arrow designation TAGGING Valves may be tagged per customer specification Example: AHU FCU-2 Valve set up required prior to ordering. Multi-Function Technology Model Control Input Running Time Built-in Feedback List Price P VDC VDC No Charge P VDC VDC No Charge P VDC VDC No Charge P VDC VDC No Charge P VDC VDC No Charge P sec. PWM VDC No Charge P sec. PWM VDC No Charge P sec. PWM VDC No Charge P Floating Point VDC No Charge P-10019* On/Off VDC No Charge Example: LRX24-MFT is the basic model. Add the P pre-set MFT configuration number and list price to the actuator when ordering, as needed. Note: Most popular configurations available at no additional cost. All other configurations carry a $3 list price. *Please Note: For On/Off control input, please order P and wire as on/off. ORDERING EXAMPLE 1 2 Choose the desired valve/actuator combination based on valve ratings and actuator control parameters from the following pages. PICCV PT + LRX24-MFT Specify Configuration (important) Multi-Function Technology: P (2-10 VDC input / 2-10 VDC feedback) Set-up: NO (Normally Open) Tagging: AHU PICCV PT+LRX24-MFT+P NO+AHU Total List Price 5

6 Pressure Independent Characterized Control Valves (PICCV) Features and Benefits Characterizing disc made of Tefzel known for excellent strength and chemical resistance Thermal isolating adapter between flange and actuator Easy direct coupling of actuator with a single screw Vent holes reduce condensation build-up Actuator can be mounted in four different positions Perpendicular mounting flange and square drive head eliminate lateral forces on the stem Blow-out proof stem with thrust-bearing Teflon disc and double O-ring design for long service life* Forged brass valve body no pin-hole leaks Teflon seats with O-rings provide constant seating force against the ball and reduce torque requirement* Regulator Assembly Non-corroding chrome-plated brass Patented Disadvantages of Today s Systems Advantages of the PICCV Time consuming balancing effort Rebalancing required when adding to system or remodeling Poor valve authority at average or low load Balancing procedure dictates quality Potential spreading of control problems can occur when one or more loops are instable, due to interactive nature of circuits Low T reduces efficiency of chillers, condensing boilers, or coils Starving of terminals in less favored spaces results in long start-up time Features Automatic dynamic system balancing Field adjustable flow rate 5 50 PSI differential pressure operating range (gradual flow will increase from 0-5 PSI) GPM (1/2 2 ) 5 year warranty Easy selection, no Cv calculation required Hydronic balancing is simplified, as the circuits are not interactive Flexible commissioning One piece installation saves 50% of labor costs, installation space, and investment for for balancing valve Reduces pumping costs Maintains T for higher efficiency of chillers and condensing boilers Visualizes flow in a BMS system and provides accurate flow for each degree of opening Prevents overflow or underflow for fast start-up Options P/T ports for flow or temperature measurement Belimo PC-Tool for commissioning Customized Flows Certified Factory Calibrated Flows Weather shields Auxiliary switches Metric threads *Teflon is a registered product of Dupont 6

7 Pressure Independent Characterized Control Valve TM (PICCV) The Best Way to Control Flow Maintain design flow independent of pressure variations The PICCV is a two-way valve that will supply a specific flow for each degree of ball opening regardless of pressure variations in a system. Flow accuracy ± 5% (5 to 50 PSI) (absolute) Variation due to ± 5% (5 to 50 PSI) manufacturing tolerances Hysteresis 1% (absolute) Flow Rate (GPM) PICCV Performance Operating Differential Range of 5 50 PSI Differential Pressure PSI 100% 90% 80% 70% 60% 50% 40% % Ball Opening Operation PICCV consists of a differential pressure regulator in series with a control valve. Regulator Section Control Valve Section The amount of flow that passes through the valve is controlled by the use of a pressure regulator that moves according to the change in pressure above and below it. All pressure changes are absorbed by the pressure regulator allowing the differential pressure to be held constant over the control valve section thereby giving the same flow. Water enters valve pressure is P1 (high) Water passes through regulator, disc, and ball pressure drops Low pressure pulls regulator down against the spring force hence reducing the regulator opening, reducing the flow. Water exits valve pressure is P2 (low) Ports sense pressure drop and transfer it through this channel below regulator 7

8 P2 Series Pressure Independent Characterized Control Valve with MFT, Non-Spring Return Actuator Two-way Valve with Chrome Plated Brass Ball and Brass Stem, NPT Female Ends Service: Flow Characteristic: Media Temp Range: chilled or hot water, 60% glycol equal percentage 0 F to 212 F [-18 C to 100 C] Ambient Temp Range: -22 F to 122 F [-30 C to 50 C] Differential Pressure Across Valve Range (ΔP): 5 to 50 psid Maximum Flow Setting: Manual Field Adjustable LRB24-3 Actuators PC Tool Field Adjustable MFT Actuators LRB P2 Pressure Independent Characterized Control Valve, Chrome Plated Brass Ball and Brass Stem Valve Non-Spring Return Actuator Model Valve Floating Proportional/MFT # Flow Rate Nominal Size Close- PICCV Liter/ DN Off Valve GPM sec Inches mm psi LRB24-3 LRX24-MFT PICCV * / Pg 12 Pg 13 PICCV * / Pg 12 Pg 13 PICCV * / Pg 12 Pg 13 PICCV * / Pg 12 Pg 13 PICCV * / Pg 12 Pg 13 PICCV * / Pg 12 Pg 13 PICCV * / Pg 12 Pg 13 PICCV / Pg 12 Pg 13 PICCV / Pg 12 Pg 13 PICCV / Pg 12 Pg 13 PICCV / Pg 12 Pg 13 PICCV / Pg 12 Pg 13 PICCV ** Pg 12 Pg 13 PICCV ** Pg 12 Pg 13 PICCV ** Pg 12 Pg 13 PICCV ** Pg 12 Pg 13 Electrical 3 ft cable 3 ft cable Connection 1/2 conduit fitting 1/2 conduit fitting When ordering MFT, see configuration codes under MFT Adjustment Tables (for example, see page 14). Note: FlowSetR only available on (-3) actuator. Refer to page 53 for customized flows and certified factory calibration flows. Options (add to list price) LRB24-3-S Built-in aux. switch (-S) Pg 12 *1/2 body has two different disc sizes (.50 GPM to 1 GPM) (1.5 GPM to 5.5 GPM) **1 body has two different disc sizes (11 GPM to 16 GPM) (17 GPM to 19 GPM) LRB24-3 LRX24-MFT 8

9 P2 Series Pressure Independent Characterized Control Valve with MFT, Spring Return Actuator Two-way Valve with Chrome Plated Brass Ball and Brass Stem, NPT Female Ends Service: Flow Characteristic: Media Temp Range: chilled or hot water, 60% glycol equal percentage 0 F to 212 F [-18 C to 100 C] Ambient Temp Range: -22 F to 122 F [-30 C to 50 C] Differential Pressure Across Valve Range (ΔP): 5 to 50 psid Maximum Flow Setting: PC Tool Field Adjustable MFT Actuators TF LF P2 Pressure Independent Characterized Control Valve, Chrome Plated Brass Ball and Brass Stem Valve Spring Return Actuator Model Valve Proportional/MFT # Flow Rate Nominal Size Close- PICCV Liter/ DN Off Valve GPM sec Inches mm psi TF24-MFT US LF24-MFT US PICCV * / Pg 17 Pg 19 PICCV * / Pg 17 Pg 19 PICCV * / Pg 17 Pg 19 PICCV * / Pg 17 Pg 19 PICCV * / Pg 17 Pg 19 PICCV * / Pg 17 Pg 19 PICCV * / Pg 17 Pg 19 PICCV / Pg 19 PICCV / Pg 19 PICCV / Pg 19 PICCV / Pg 19 PICCV / Pg 19 PICCV ** Pg 19 PICCV ** Pg 19 PICCV ** Pg 19 PICCV ** Pg 19 Electrical 3 ft cable 3 ft cable Connection 1/2 conduit fitting 1/2 conduit fitting TF24-MFT US LF24-MFT US When ordering MFT, see configuration codes under MFT Adjustment Tables (for example, see page 18). Refer to page 53 for customized flows and certified factory calibration flows. Options (add to list price) LF24-MFT-S US Built-in aux. switch (-S) Pg 19 *1/2 body has two different disc sizes (.50 GPM to 1 GPM) (1.5 GPM to 5.5 GPM) **1 body has two different disc sizes (11 GPM to 16 GPM) (17 GPM to 19 GPM) 9

10 P2 Series Pressure Independent Characterized Control Valve with MFT, Non-Spring Return Actuator Two-way Valve with Chrome Plated Brass Ball and Brass Stem with P/T ports, NPT Female Ends Service: Flow Characteristic: Media Temp Range: chilled or hot water, 60% glycol equal percentage 0 F to 212 F [-18 C to 100 C] Ambient Temp Range: -22 F to 122 F [-30 C to 50 C] Differential Pressure Across Valve Range ( P): 5 to 50 psid Maximum Flow Setting: Manual Field Adjustable LRB24-3 Actuators PC Tool Field Adjustable MFT Actuators ARX P2 Pressure Independent Characterized Control Valve, Chrome Plated Brass Ball and Brass Stem, P/T ports Valve Non-Spring Return Actuator Model Valve Floating Proportional/MFT # Flow Rate Nominal Size Close- PICCV Liter/ DN Off LRB24-3 LRX24-MFT Valve GPM sec Inches mm psi ARX24-MFT PICCV PT* / Pg 12 Pg 13 PICCV PT* / Pg 12 Pg 13 PICCV PT* / Pg 12 Pg 13 PICCV PT* / Pg 12 Pg 13 PICCV PT* / Pg 12 Pg 13 PICCV PT* / Pg 12 Pg 13 PICCV PT* / Pg 12 Pg 13 PICCV PT / Pg 12 Pg 13 PICCV PT / Pg 12 Pg 13 PICCV PT / Pg 12 Pg 13 PICCV PT / Pg 12 Pg 13 PICCV PT / Pg 12 Pg 13 PICCV PT** Pg 12 Pg 13 PICCV PT** Pg 12 Pg 13 PICCV PT** Pg 12 Pg 13 PICCV PT** Pg 12 Pg 13 PICCV PT / Pg 23 PICCV PT / Pg 23 PICCV PT / Pg 23 PICCV PT / Pg 23 PICCV PT / Pg 23 PICCV PT / Pg 23 PICCV PT / Pg 23 PICCV PT / Pg 23 PICCV PT / Pg 23 PICCV PT Pg 23 PICCV PT Pg 23 PICCV PT Pg 23 PICCV PT Pg 31 PICCV PT Pg 31 PICCV PT Pg 31 PICCV PT Pg 31 PICCV PT Pg 31 PICCV PT Pg 31 PICCV PT Pg 31 PICCV PT Pg 31 PICCV PT Pg 31 PICCV PT Pg 31 PICCV PT Pg 31 Electrical 3 ft cable 3 ft cable Connection 1/2 conduit fitting 1/2 conduit fitting When ordering MFT, see configuration codes under MFT Adjustment Tables (for example, see page 14). Note: FlowSetR only available on (-3) actuator. Refer to page 53 for customized flows and certified factory calibration flows. Options (add to list price) LRB24-3-S Built-in aux. switch (-S) Pg 12 *1/2 body has two different disc sizes (.50 GPM to 1 GPM) (1.5 GPM to 5.5 GPM) **1 body has two different disc sizes (11 GPM to 16 GPM) (17 GPM to 19 GPM) LRB24-3 ARX24-MFT LRX24-MFT 10

11 P2 Series Pressure Independent Characterized Control Valve with MFT, Spring Return Actuator Two-way Valve with Chrome Plated Brass Ball and Brass Stem with P/T ports, NPT Female Ends Service: chilled or hot water, 60% glycol Flow Characteristic: equal percentage Media Temp Range: 0 F to 212 F [-18 C to 100 C] Ambient Temp Range: -22 F to 122 F [-30 C to 50 C] Differential Pressure Across Valve Range ( P): 5 to 50 psid Maximum Flow Setting: PC Tool Field Adjustable MFT Actuators AF P2 Pressure Independent Characterized Control Valve, Chrome Plated Brass Ball and Brass Stem, P/T ports Valve Spring Return Actuator Model Valve Proportional/MFT # Flow Rate Nominal Size Close- PICCV Liter/ DN Off TF24-MFT US LF24-MFT US Valve GPM sec Inches mm psi AF24-MFT US PICCV PT* / Pg 17 Pg 19 PICCV PT* / Pg 17 Pg 19 PICCV PT* / Pg 17 Pg 19 PICCV PT* / Pg 17 Pg 19 PICCV PT* / Pg 17 Pg 19 PICCV PT* / Pg 17 Pg 19 PICCV PT* / Pg 17 Pg 19 PICCV PT / Pg 19 PICCV PT / Pg 19 PICCV PT / Pg 19 PICCV PT / Pg 19 PICCV PT / Pg 19 PICCV PT** Pg 19 PICCV PT** Pg 19 PICCV PT** Pg 19 PICCV PT** Pg 19 PICCV PT / Pg 27 PICCV PT / Pg 27 PICCV PT / Pg 27 PICCV PT / Pg 27 PICCV PT / Pg 27 PICCV PT / Pg 27 PICCV PT / Pg 27 PICCV PT / Pg 27 PICCV PT / Pg 27 PICCV PT Pg 27 PICCV PT Pg 27 PICCV PT Pg 27 PICCV PT Pg 33 PICCV PT Pg 33 PICCV PT Pg 33 PICCV PT Pg 33 PICCV PT Pg 33 PICCV PT Pg 33 PICCV PT Pg 33 PICCV PT Pg 33 PICCV PT Pg 33 PICCV PT Pg 33 PICCV PT Pg 33 Electrical 3 ft cable 3 ft cable Connection 1/2 conduit fitting 1/2 conduit fitting When ordering MFT, see configuration codes under MFT Adjustment Tables (for example, see page 18). Refer to page 53 for customized flows and certified factory calibration flows. TF24-MFT US LF24-MFT US AF24-MFT US Options (add to list price) LF24-MFT-S US AF24-MFT-S US Built-in aux. switch (-S) Pg 19 Pg 27 & 33 *1/2 body has two different disc sizes (.50 GPM to 1 GPM) (1.5 GPM to 5.5 GPM) **1 body has two different disc sizes (11 GPM to 16 GPM) (17 GPM to 19 GPM) 11

12 Pressure Independent Characterized Control Valve with Floating, Non-Spring Return Actuator, P/T Ports (Optional) Application: The Pressure Independent Characterized Control Valve is typically used in air handling units on heating and cooling coils and fan coil unit heating or cooling coils. Some other common applications include unit ventilators and VAV re-heat coils. This valve is suitable for use in a hydronic system with constant or variable flow. Valve Specifications Service chilled or hot water, 60% glycol Flow characteristic equal percentage Size 1/2, 3/4, 1 Type of end fitting female, NPT Materials: Body forged brass, nickel plated Ball chrome plated brass Stem chrome plated brass Seat O-rings Viton Seat fiberglass reinforced teflon PTFE Characterizing disc TEFZEL Packing 2 EPDM O-rings, lubricated Diaphragm polyester reinforced silicone Regulator components stainless steel/brass/delrin 500 AF Spring stainless steel Pete s Plugs* (Qty 2) 1/4 brass/nortel (Optional-P/T) Body pressure rating 600 PSI Media temp. range 0 F to 212 F [-18 C to 100 C] Close off pressure 200 PSI Leakage ANSI Class IV (0.01% of rated valve capacity at 50 psi differential) Flow rate 1/2 0.5 GPM [.03 l/s], 1 GPM [.06 l/s], 1.50 GPM [0.09 l/s], 2 GPM [.13 l/s], 3 GPM [.19 l/s], 4 GPM [.25 l/s], 5 GPM [.32 l/s] Flow rate 3/4 6 GPM [0.37 l/s], 7 GPM [0.44 l/s], 8 GPM [0.50 l/s], 9 GPM [0.57 l/s], 10 GPM [0.63 l/s] Flow rate 1 12 GPM [0.76 l/s], 14 GPM [0.88 l/s], 16 GPM [1.01 l/s], 18 GPM [1.14 l/s] Rangeability 100 : 1 Differential pressure 5 to 50 PSI operating range Flow accuracy (absolute) ± 5% (5 to 50 PSI) Variation due to ± 5% (5 to 50 PSI) manufacturing tolerances Hysteresis (absolute) 1% Weight of valve body 1/2 = 2.52 lbs 3/4 = 3.05 lbs 1 = 4.98 lbs Tefzel and Teflon are registered trademarks of Dupont Actuator Specifications LRB24-3 on/off-floating Power Supply 24 VAC ± 20% 50/60 Hz 24 VDC ± 10% Power Consumption 1.5 W (0.2 W) Transformer Sizing 3 VA (Class 2 power source) Electrical Connection 3 ft, 18 GA plenum rated cable 3 ft, 18 GA appliance rated cable (-S) 1/2 conduit connector Overload Protection electronic throughout 0 to 95 rotation Control on/off, floating point Input Impedance 600Ω Direction of Rotation reversible with switch Position Indication handle Manual Override external push button and handle Running Time 95 seconds, constant independent of load Humidity 5 to 95% RH non condensing (EN ) Ambient Temperature -22 F to +122 F [-30 C to +50 C] Storage Temperature -40 F to +176 F [-40 C to +80 C] Housing NEMA 2/IP54 Housing Material UL94-5VA Agency Listings culus acc. to UL A/-2-14, CAN/CSA E , CSA C22.2 No , CE acc. to 89/336/EEC and (-S Models) 2006/95/EC Noise Level <35dB(A) Servicing maintenance free Quality Standard ISO 9001 Weight 1.1lbs [0.5 Kg], LRB24-3-S Auxiliary switch 1 x SPDT, 3A (0.5A 250 VAC Weight of actuator 1.4 lbs [0.64 Kg] Rated Impulse Voltage 800V, Type of action 1, (1.B for -S version), Control Pollution Degree 3. 12

13 Pressure Independent Characterized Control Valve with MFT, Non-Spring Return Actuator, P/T Ports (Optional) Application: The Pressure Independent Characterized Control Valve is typically used in air handling units on heating and cooling coils and fan coil unit heating or cooling coils. Some other common applications include unit ventilators and VAV re-heat coils. This valve is suitable for use in a hydronic system with constant or variable flow. This valve is designed with MFT functionality which facilitates the use of various control input. Valve Specifications Service chilled or hot water, 60% glycol Flow characteristic equal percentage Size 1/2, 3/4, 1 Type of end fitting female, NPT Materials: Body forged brass, nickel plated Ball chrome plated brass Stem chrome plated brass Seat O-rings Viton Seat fiberglass reinforced teflon PTFE Characterizing disc TEFZEL Packing 2 EPDM O-rings, lubricated Diaphragm polyester reinforced silicone Regulator components stainless steel/brass/delrin 500 AF Spring stainless steel Pete s Plugs* (Qty 2) 1/4 brass/nortel (Optional-P/T) Body pressure rating 600 PSI Media temp. range 0 F to 212 F [-18 C to 100 C] Close off pressure 200 PSI Leakage ANSI Class IV (0.01% of rated valve capacity at 50 psi differential) Flow rate 1/2 0.5 GPM [.03 l/s], 1 GPM [.06 l/s], 1.50 GPM [0.09 l/s], 2 GPM [.13 l/s], 3 GPM [.19 l/s], 4 GPM [.25 l/s], 5 GPM [.32 l/s] Flow rate 3/4 6 GPM [0.37 l/s], 7 GPM [0.44 l/s], 8 GPM [0.50 l/s], 9 GPM [0.57 l/s], 10 GPM [0.63 l/s] Flow rate 1 12 GPM [0.76 l/s], 14 GPM [0.88 l/s], 16 GPM [1.01 l/s], 18 GPM [1.14 l/s] Rangeability 100 : 1 Differential pressure 5 to 50 PSI operating range Flow accuracy (absolute) ± 5% (5 to 50 PSI) Variation due to ± 5% (5 to 50 PSI) manufacturing tolerances Hysteresis (absolute) 1% Weight of valve body 1/2 = 2.52 lbs 3/4 = 3.05 lbs 1 = 4.98 lbs Tefzel and Teflon are registered trademarks of Dupont Actuator Specifications LRX24-MFT Power Supply 24 VAC ± 20% 50/60 Hz 24 VDC ± 10% Power Consumption 2 W (1.2 W) Transformer Sizing 3.5 VA (Class 2 power source) Electrical Connection 18 GA plenum rated cable 1/2 conduit connector 3 ft [1m] 10 ft [3m] 16 ft [5m] Overload Protection electronic throughout 0 to 95 rotation Operating Range Y 2 to 10 VDC, 4 to 20 ma (default) Variable (VDC, PWM, Floating Point, On/Off) Input Impedance 100kΩ (0.1 ma), 500Ω 1500Ω (PWM, Floating Point, On/Off) Feedback Output U 2 to 10 Vdc, 0.5mA max VDC Variable Torque 45 in-lb [5 Nm] Direction of Rotation reversible with switch Position Indication reflective visual indicator (snap-on) Manual Override external push button Running Time Motor* 100 sec constant Humidity 5 to 95% RH non condensing (EN ) Ambient Temperature -22 F to +122 F [-30 C to +50 C] Storage Temperature -40 F to +176 F [-40 C to +80 C] Housing NEMA 2/IP54 Housing Material UL94-5VA Agency Listings culus acc. to UL A/-2-14, CAN/CSA E , CSA C22.2 No , CE acc. to 89/336/EEC Noise Level <35dB(A) Servicing maintenance free Quality Standard ISO 9001 Weight 1.10 lbs [0.50 kg] *PICCV/LRX24-MFT must remain at 100 sec constant run time Rated Impulse Voltage 800V, Type of action 1, Control Pollution Degree 3. MFT 13

14 Pressure Independent Characterized Control Valve with MFT, Non-Spring Return Actuator, P/T Ports (Optional) 1/2, GPM The PICCV has a unique feature in that the GPM can be adjusted by adjusting the minimum and maximum settings. Selecting the Proper Flow Rate: The PICCV (-PT) can be ordered in 0.50 GPM or 1.0 GPM flow rates. The PICCV (-PT) can be ordered in 1.5 GPM to 5.5 GPM flow rate increments, as stated in the table below. If you wish to re-program to the values listed in the table below: Example 1: The application requires a 2 GPM flow rate. Solution: Order the PICCV Example 2: The application requires a 3.5 GPM flow rate. Solution: Order the PICCV and re-program to the below setting for 3.5 GPM. As a standard, the PICCV is available in flows of 4 GPM and 3 GPM. If you desire 3.5 GPM and have a Normally Closed (NC) valve, simply reprogram the maximum setting to 71%, and minimum setting of 0% as indicated on the chart below. Please note that the settings are different for Normally Closed (NC) and Normally Open (NO) operation. When ordering, please specify NO or NC operation. Selecting the Proper Control Signal Select one of the MFT codes below for the signal required. Example: A 3 GPM flow rate is required, non-spring return actuator, 2-10 VDC signal. Solution: PICCV LRX24-MFT + P Engineering Note: The 1/2 PICCV utilizes two uniquely engineered valve bodies to achieve the listed flow rate offerings. Variable GPMs are further realized using Belimo s registered Multi- Function Technology. The PICCV offers nominal flow rates that are adjustable from 0.5 to 1.0 GPM. The PICCV offers nominal flow rates that are adjustable from 1.5 to 5.5 GPM range. Please follow MFT guideline settings when configuring the PICCV MFT actuators in the field. MFT Adjustment Table NC will open as voltage increases (no flow at 0-2V) - actuator switch on Y2 Default* Flow Adjustable** Flow rate Flow rate MFT angle of MFT angle of Product Range GPM l/s GPM l/s rotation max. setting rotation min. setting PICCV (-PT) + LRX24-MFT % 0% NEW PICCV (-PT) + LRX24-MFT % 0% NEW PICCV (-PT) + LRX24-MFT % 0% PICCV (-PT) + LRX24-MFT % 0% PICCV (-PT) + LRX24-MFT % 0% PICCV (-PT) + LRX24-MFT % 0% % 0% PICCV (-PT) + LRX24-MFT % 0% % 0% PICCV (-PT) + LRX24-MFT % 0% % 0% PICCV (-PT) + LRX24-MFT % 0% % 0% MFT Adjustment Table NO will close as voltage increases (no flow at 10V) - actuator switch on Y1 Default* Flow Adjustable** Flow rate Flow rate MFT angle of MFT angle of Product Range GPM l/s GPM l/s rotation max. setting rotation min. setting PICCV (-PT) + LRX24-MFT % 33% NEW PICCV (-PT) + LRX24-MFT % 12% NEW PICCV (-PT) + LRX24-MFT % 55% PICCV (-PT) + LRX24-MFT % 37% PICCV (-PT) + LRX24-MFT % 43% PICCV (-PT) + LRX24-MFT % 40% % 37% PICCV (-PT) + LRX24-MFT % 35% % 32% PICCV (-PT) + LRX24-MFT % 28% % 25% PICCV (-PT) + LRX24-MFT % 20% % 18% *Preprogrammed at factory **Customer reprogrammable using MFT PC tool / or can be factory set. Note: 1/2 valve has 2 disc sizes (.5 to 1 GPM) (1.5 to 5.5 GPM) For replacement or re-programming, please contact Technical Support Multi-Function Technology Model Control Input Running Time Built-in Feedback List Price P VDC VDC No Charge P VDC VDC No Charge P sec. PWM VDC No Charge P sec. PWM VDC No Charge P sec. PWM VDC No Charge P Floating Point VDC No Charge P-10019* On/Off VDC No Charge Example: LRX24-MFT is the basic model. Add the P pre-set MFT configuration number and list price to the actuator when ordering, as needed. Note: Most popular configurations available at no additional cost. All other configurations carry a $3 list price. *Please Note: For On/Off control input, please order P and wire as on/off. 14 For complete technical information and list of configuration codes refer to Product Documentation Multi-Function Technology For Damper and Control Valve Applications

15 Pressure Independent Characterized Control Valve with MFT, Non-Spring Return Actuator, P/T Ports (Optional) 3/4, 6 10 GPM The PICCV has a unique feature in that the GPM can be adjusted by adjusting the minimum and maximum settings. Selecting the Proper Flow Rate: The PICCV (-PT) can be ordered in 6 GPM to 10 GPM flow rate increments, as stated in the table below. If you wish to re-program to the values listed in the table below: Example 1: The application requires a 6 GPM flow rate. Solution: Order the PICCV Example 2: The application requires a 8.5 GPM flow rate. Solution: Order the PICCV and re-program to the below setting for 8.5 GPM. As a standard, the PICCV is available in flows of 8 GPM and 9 GPM. If you desire 8.5 GPM and have a Normally Closed (NC) valve, simply reprogram the maximum setting to 82%, and minimum setting of 0% as indicated on the chart below. Please note that the settings are different for Normally Closed (NC) and Normally Open (NO) operation. When ordering, please specify NO or NC operation. Selecting the Proper Control Signal Select one of the MFT codes below for the signal required. Example: A 6 GPM flow rate is required, non-spring return actuator, 2-10 VDC signal. Solution: PICCV LRX24-MFT + P Engineering Note: The 3/4 PICCV utilizes a uniquely engineered valve body to achieve the listed flow rate offerings. Variable GPMs are further realized using Belimo s registered Multi-Function Technology. The PICCV offers nominal flow rates that are adjustable from 6 to 10 GPM. Please follow MFT guideline settings when configuring the PICCV MFT actuators in the field. MFT Adjustment Table NC will open as voltage increases (no flow at 0-2V) - actuator switch on Y 2 Default* Flow Adjustable** Flow rate Flow rate MFT angle of MFT angle of Product Range GPM l/s GPM l/s rotation max. setting rotation min. setting PICCV (-PT) + LRX24-MFT % 0% % 0% PICCV (-PT) + LRX24-MFT % 0% % 0% PICCV (-PT) + LRX24-MFT % 0% % 0% PICCV (-PT) + LRX24-MFT % 0% % 0% PICCV (-PT) + LRX24-MFT % 0% MFT Adjustment Table NO will close as voltage increases (no flow at 10V) - actuator switch on Y 1 Default* Flow Adjustable** Flow rate Flow rate MFT angle of MFT angle of Product Range GPM l/s GPM l/s rotation max. setting rotation min. setting PICCV (-PT) + LRX24-MFT % 31% % 28% PICCV (-PT) + LRX24-MFT % 27% % 25% PICCV (-PT) + LRX24-MFT % 24% % 22% PICCV (-PT) + LRX24-MFT % 19% % 18% PICCV (-PT) + LRX24-MFT % 13% *Preprogrammed at factory Multi-Function Technology **Customer reprogrammable using MFT PC tool / or can be factory set. For complete technical information and list of configuration codes refer to Product Documentation Multi-Function Technology For Damper and Control Valve Applications Model Control Input Running Time Built-in Feedback List Price P VDC VDC No Charge P VDC VDC No Charge P sec. PWM VDC No Charge P sec. PWM VDC No Charge P sec. PWM VDC No Charge P Floating Point VDC No Charge P-10019* On/Off VDC No Charge Example: LRX24-MFT is the basic model. Add the P pre-set MFT configuration number and list price to the actuator when ordering, as needed. Note: Most popular configurations available at no additional cost. All other configurations carry a $3 list price. *Please Note: For On/Off control input, please order P and wire as on/off. 15

16 Pressure Independent Characterized Control Valve with MFT, Non-Spring Return Actuator, P/T Ports (Optional) 1, GPM The PICCV has a unique feature in that the GPM can be adjusted by adjusting the minimum and maximum settings. Selecting the Proper Flow Rate: The PICCV can be ordered in 2 ways. The PICCV can be reprogrammed to offer flows from 11 GPM 16 GPM. Example 1: The application requires a 14 GPM flow rate. Solution: Order the PICCV Example 2: The application requires a 15 GPM flow rate. Solution: Order the PICCV and re-program to the below setting for 15 GPM. As a standard, the PICCV is available in flows of 14 GPM and 16 GPM. If you desire 15 GPM and have a Normally Closed (NC) valve, simply reprogram the maximum setting to 83%, and minimum setting of 0% as indicated on the chart below. Please note that the settings are different for Normally Closed (NC) and Normally Open (NO) operation. When ordering, please specify NO or NC operation. Selecting the Proper Control Signal Select one of the MFT codes below for the signal required. Example: A 14 GPM flow rate is required, non-spring return actuator, 2-10 VDC signal. Solution: PICCV LRX24-MFT+ P Engineering Note: The 1 PICCV utilizes two uniquely engineered valve bodies to achieve the listed flow rate offerings. Variable GPMs are further realized using Belimo s registered Multi-Function Technology. The PICCV offers nominal flow rates that are adjustable from 11 to 16 GPM. The PICCV offers nominal flow rates that are adjustable from 17 to 19 GPM range. Please follow MFT guideline settings when configuring the PICCV MFT actuators in the field. MFT Adjustment Table NC will open as voltage increases (no flow at 0-2V) - actuator switch on Y 2 Default* Flow Adjustable** Flow rate Flow rate MFT angle of MFT angle of Product Range GPM l/s GPM l/s rotation max. setting rotation min. setting % 0% PICCV (-PT) + LRX24-MFT % 0% % 0% PICCV (-PT) + LRX24-MFT % 0% % 0% PICCV (-PT) + LRX24-MFT % 0% PICCV (-PT)+ LRX24-MFT % 0% % 0% % 0% MFT Adjustment Table NO will close as voltage increases (no flow at 10V) - actuator switch on Y 1 Default* Flow Adjustable** Flow rate Flow rate MFT angle of MFT angle of Product Range GPM l/s GPM l/s rotation max. setting rotation min. setting % 26% PICCV (-PT) + LRX24-MFT % 24% % 20% PICCV (-PT) + LRX24-MFT % 16% % 9% PICCV (-PT) + LRX24-MFT % 0% PICCV (-PT) + LRX24-MFT % 22% % 15% % 11% *Preprogrammed at factory **Customer reprogrammable using MFT PC tool / or can be factory set. 1 valve has 2 disc sizes (11 GPM to 16 GPM) (17 GPM to 19 GPM) Multi-Function Technology For complete technical information and list of configuration codes refer to Product Documentation Multi-Function Technology For Damper and Control Valve Applications Model Control Input Running Time Built-in Feedback List Price P VDC VDC No Charge P VDC VDC No Charge P sec. PWM VDC No Charge P sec. PWM VDC No Charge P sec. PWM VDC No Charge P Floating Point VDC No Charge P-10019* On/Off VDC No Charge Example: LRX24-MFT is the basic model. Add the P pre-set MFT configuration number and list price to the actuator when ordering, as needed. Note: Most popular configurations available at no additional cost. All other configurations carry a $3 list price. *Please Note: For On/Off control input, please order P and wire as on/off. 16

17 Pressure Independent Characterized Control Valve with MFT, Spring Return Actuator, P/T Ports (Optional) Valve Specifications Service chilled or hot water, 60% glycol Flow characteristic equal percentage Size 1/2 Type of end fitting female, NPT Materials: Body forged brass, nickel plated Ball chrome plated brass Stem chrome plated brass Seat O-rings Viton Seat fiberglass reinforced teflon PTFE Characterizing disc TEFZEL Packing 2 EPDM O-rings, lubricated Diaphragm polyester reinforced silicone Regulator components stainless steel/brass/delrin 500 AF Spring stainless steel Pete s Plugs* (Qty 2) 1/4 brass/nortel (Optional-P/T) Body pressure rating 600 PSI Media temp. range 0 F to 212 F [-18 C to 100 C] Close off pressure 200 PSI Leakage ANSI Class IV (0.01% of rated valve capacity at 50 psi differential) Flow rate 1/2 0.5 GPM [.03 l/s], 1 GPM [.06 l/s], 1.50 GPM [0.09 l/s], 2 GPM [.13 l/s], 3 GPM [.19 l/s], 4 GPM [.25 l/s], 5 GPM [.32 l/s] Rangeability 100 : 1 Differential pressure 5 to 50 PSI operating range Flow accuracy (absolute) ± 5% (5 to 50 PSI) Variation due to ± 5% (5 to 50 PSI) manufacturing tolerances Hysteresis (absolute) 1% Weight of valve body 1/2 = 2.52 lbs 3/4 = 3.05 lbs 1 = 4.98 lbs Application: The Pressure Independent Characterized Control Valve is typically used in air handling units on heating and cooling coils and fan coil unit heating or cooling coils. Some other common applications include unit ventilators and VAV re-heat coils. This valve is suitable for use in a hydronic system with constant or variable flow. This valve is designed with MFT functionality which facilitates the use of various control input. Actuator Specifications TF24-MFT US Power supply 24 VAC ± 20% 50/60 Hz 24 VDC ± 10% Power consumption running: 2.5 W; holding: 1 W Transformer sizing 4 VA (class 2 power source) Electrical connection TF24-MFT US 3 ft, 18 GA plenum rated cable 1/2 conduit connector Overload protection electronic throughout 0 to 95 rotation Operating range Y 2 to 10 VDC 4 to 20 ma (w/500ω, 1/4 W resistor) ZG-R01 Input impedance 100kΩ for 2 to 10 VDC (0.1 ma) 500Ω for 4 to 20 ma 1500Ω for PWM, Floating point and On-Off control Feedback output U 2 to 10 VDC, 0.5 ma max Torque min 18 in-lb (2 Nm) Direction of rotation spring: reversible with cw/ccw mounting motor: reversible with built-in switch Mech. angle of rotation max 95, adjust with mechanical stop Running time motor* 100 sec constant Running time spring <25 F to F [-20 C to +50 C] <60 F [-30 C] Angle of Rotation Off (Default) Adaptation Override control Min. (Min Position) = 0% - ZS (Mid. Position) = 50% - Max. (Max. Position) = 100% Position indication visual indicator, 0 to 95 Humidity 5 to 95% RH, non-condensing Ambient temperature -22 to +122 F (-30 to +50 C) Storage temperature -40 to +176 F (-40 to +80 C) Housing NEMA 2, IP42 Housing material UL 94-5VA Noise level Max: <35 db (A) Spring Return <65 db (A) Agency listings culus acc. to UL A/-2-14, CAN/CSA E , CSA C22.2 No.24-93, CE acc. to 89/336/EEC Quality standard ISO 9001 Servicing maintenance free Weight 1.4 lbs. (0.6 kg.) *PICCV/TF24-MFT US must remain at 100 sec constant run time Rated Impulse Voltage 800V, Type of action 1.AA (1.AA.B for -S version), Control Pollution Degree 3. Tefzel and Teflon are registered trademarks of Dupont MFT 17

18 Pressure Independent Characterized Control Valve with MFT, Spring Return Actuator, P/T Ports (Optional) 1/2, GPM The PICCV has a unique feature in that the GPM can be adjusted by adjusting the minimum and maximum settings. Selecting the Proper Flow Rate: The PICCV (-PT) can be ordered in 0.50 GPM or 1.0 GPM flow rates. The PICCV (-PT) can be ordered in 1.5 GPM to 5.5 GPM flow rate increments, as stated in the table below. If you wish to re-program to the values listed in the table below: Example 1: The application requires a 2 GPM flow rate. Solution: Order the PICCV Example 2: The application requires a 3.5 GPM flow rate. Solution: Order the PICCV and re-program to the below setting for 3.5 GPM. As a standard, the PICCV is available in flows of 4 GPM and 3 GPM. If you desire 3.5 GPM and have a Normally Closed, Fail Open (NC, FO) valve, simply reprogram the maximum setting to 75%, and minimum setting of 0% as indicated on the chart below. Please note that the settings are different for Normally Closed, Fail Open or Fail Closed (NC, FO or FC) and Normally Open, Fail Open or Fail Closed (NO, FO or FC) operation. When ordering, please specify NO or NC operation. Selecting the Proper Control Signal Select one of the MFT codes below for the signal required. Example: A 3 GPM flow rate is required, spring return actuator, 2-10 VDC signal. Solution: PICCV TF24-MFT US + P Engineering Note: The 1/2 PICCV utilizes two uniquely engineered valve bodies to achieve the listed flow rate offerings. Variable GPMs are further realized using Belimo s registered Multi- Function Technology. The PICCV offers nominal flow rates that are adjustable from 0.5 to 1.0 GPM. The PICCV offers nominal flow rates that are adjustable from 1.5 to 5.5 GPM range. Please follow MFT guideline settings when configuring the PICCV MFT actuators in the field. MFT Adjustment Table NC will open as voltage increases (no flow at 0-2V) - actuator switch on W Default* Flow Adjustments** Flow rate Flow rate MFT angle of MFT angle of Product Range GPM l/s GPM l/s rotation max. setting rotation min. setting PICCV (-PT)+ TF24-MFT US FO 80%, FC 73% FO, FC 0% PICCV (-PT) + TF24-MFT US FO 94%, FC 90% FO, FC 0% PICCV (-PT)+ TF24-MFT US FO 62%, FC 58% FO, FC 0% PICCV (-PT) + TF24-MFT US FO 66%, FC 62% FO, FC 0% FO 69%, FC 65% FO, FC 0% PICCV (-PT) + TF24-MFT US FO 72%, FC 69% FO, FC 0% FO 75%, FC 71% FO, FC 0% PICCV (-PT) + TF24-MFT US FO 77%, FC 73% FO, FC 0% FO 81%, FC 77% FO, FC 0% PICCV (-PT) + TF24-MFT US FO 85%, FC 81% FO, FC 0% FO 89%, FC 85% FO, FC 0% MFT Adjustment Table NO will close as voltage increases (no flow at 10V) - actuator switch on CW Default* Flow Adjustments** Flow rate Flow rate MFT angle of MFT angle of Product Range GPM l/s GPM l/s rotation max. setting rotation min. setting PICCV (-PT)+ TF24-MFT US FO, FC 100% FO 29%, FC 34% PICCV (-PT) + TF24-MFT US FO, FC 100% FO 13%, FC 15% PICCV (-PT)+ TF24-MFT US FO, FC 100% FO 43%, FC 47% PICCV (-PT) + TF24-MFT US FO, FC 100% FO 39%, FC 43% FO, FC 100% FO 36%, FC 41% PICCV (-PT) + TF24-MFT US FO, FC 100% FO 34%, FC 38% FO, FC 100% FO 31%, FC 36% PICCV (-PT) + TF24-MFT US FO, FC 100% FO 28%, FC 33% FO, FC 100% FO 25%, FC 29% PICCV (-PT) + TF24-MFT US FO, FC 100% FO 20%, FC 25% FO, FC 100% FO 17%, FC 22% *Preprogrammed at factory **Customer reprogrammable using MFT PC tool / or can be factory set. Note: 1/2 valve has 2 disc sizes (.5 GPM to 1 GPM) (1.5 GPM to 5.5 GPM) Multi-Function Technology Model Control Input Running Time Built-in Feedback List Price P VDC VDC No Charge P VDC VDC No Charge P sec. PWM VDC No Charge P sec. PWM VDC No Charge P sec. PWM VDC No Charge P Floating Point VDC No Charge P-10019* On/Off VDC No Charge Example: TF24-MFT US is the basic model. Add the P pre-set MFT configuration number and list price to the actuator when ordering, as needed. Note: Most popular configurations available at no additional cost. All other configurations carry a $3 list price. *Please Note: For On/Off control input, please order P and wire as on/off. 18 For complete technical information and list of configuration codes refer to Product Documentation Multi-Function Technology For Damper and Control Valve Applications

19 Pressure Independent Characterized Control Valve with MFT, Spring Return Actuator, P/T Ports (Optional) Application: The Pressure Independent Characterized Control Valve is typically used in air handling units on heating and cooling coils and fan coil unit heating or cooling coils. Some other common applications include unit ventilators and VAV re-heat coils. This valve is suitable for use in a hydronic system with constant or variable flow. This valve is designed with MFT functionality which facilitates the use of various control input. Valve Specifications Service chilled or hot water, 60% glycol Flow characteristic equal percentage Size 1/2, 3/4, 1 Type of end fitting female, NPT Materials: Body forged brass, nickel plated Ball chrome plated brass Stem chrome plated brass Seat O-rings Viton Seat fiberglass reinforced teflon PTFE Characterizing disc TEFZEL Packing 2 EPDM O-rings, lubricated Diaphragm polyester reinforced silicone Regulator components stainless steel/brass/delrin 500 AF Spring stainless steel Pete s Plugs* (Qty 2) 1/4 brass/nortel (Optional-PT) Body pressure rating 600 PSI Media temp. range 0 F to 212 F [-18 C to 100 C] Close off pressure 200 PSI Leakage ANSI Class IV (0.01% of rated valve capacity at 50 psi differential) Flow rate 1/2 0.5 GPM [.03 l/s], 1 GPM [.06 l/s], 1.50 GPM [0.09 l/s], 2 GPM [.13 l/s], 3 GPM [.19 l/s], 4 GPM [.25 l/s], 5 GPM [.32 l/s] Flow rate 3/4 6 GPM [0.37 l/s], 7 GPM [0.44 l/s], 8 GPM [0.50 l/s], 9 GPM [0.57 l/s], 10 GPM [0.63 l/s] Flow rate 1 12 GPM [0.76 l/s], 14 GPM [0.88 l/s], 16 GPM [1.01 l/s], 18 GPM [1.14 l/s] Rangeability 100 : 1 Differential pressure 5 to 50 PSI operating range Flow accuracy (absolute) ± 5% (5 to 50 PSI) Variation due to ± 5% (5 to 50 PSI) manufacturing tolerances Hysteresis (absolute) 1% Weight of valve body 1/2 = 2.52 lbs, 3/4 = 3.05 lbs 1 = 4.98 lbs Tefzel and Teflon are registered trademarks of Dupont Actuator Specifications LF24-MFT US Control MFT Control signal Y 2 to 10 VDC (Default) Power supply 24 VAC ± 20% 50/60 Hz, 24 VDC ± 10% Power consumption 2.5 W running, 1 W holding Transformer sizing 5 VA (Class 2 power source) Electrical connection 3 ft, 18 GA, plenum rated cable, 1/2 conduit Overload protection electronic throughout 0 to 95 rotation Operating range 2 to 10 VDC, 4 to 20 ma (w/500 Ω, 1/4 W resistor) ZG-R01 Input impedance 100kΩ for 2 to 10 VDC (0.1 ma) 500Ω for 4 to 20 ma, 1500Ω for PWM, Floating point and On-Off control Feedback output U 2 to 10 VDC, 0.5 ma max Direction of rotation spring return reversible with CW/CCW mounting. Control direction selected by switch: CW=CW with decrease in signal CCW=CCW with a decrease in signal Running time motor* 100 sec constant Running time spring <25 F to F [-20 C to +50 C] <60 F [-30 C] Position indication visual indicator, 0 to 95 Humidity 5 to 95% RH, non-condensing Operating temp. -22 to +122 F (-30 to +50 C) Storage temp. -40 to +176 F (-40 to +80 C) Housing NEMA 2, IP54 Housing material zinc coated metal Noise level Max: <30 db (A) Spring Return <62 db (A) Agency listings UL 873 listed, CE, CSA C22.2 No. 24 certified Quality standard ISO 9001 Servicing maintenance free LF24-MFT-S US Auxiliary switch 1 SPDT, 3A (0.5A VAC Weight of actuator 3.26 lbs [1.48 Kg] *PICCV/LF24-MFT US must remain at 100 sec constant run time LISTED 94D5 TEMP. IND & REG. EQUIP. UL MFT 19

20 Pressure Independent Characterized Control Valve with MFT, Spring Return Actuator, P/T Ports (Optional) 1/2, GPM The PICCV has a unique feature in that the GPM can be adjusted by adjusting the minimum and maximum settings. Selecting the Proper Flow Rate: The PICCV (-PT) can be ordered in 0.50 GPM or 1.0 GPM flow rates. The PICCV (-PT) can be ordered in 1.5 GPM to 5.5 GPM flow rate increments, as stated in the table below. If you wish to re-program to the values listed in the table below: Example 1: The application requires a 2 GPM flow rate. Solution: Order the PICCV Example 2: The application requires a 3.5 GPM flow rate. Solution: Order the PICCV and re-program to the below setting for 3.5 GPM. As a standard, the PICCV is available in flows of 4 GPM and 3 GPM. If you desire 3.5 GPM and have a Normally Closed (NC) valve, simply reprogram the maximum setting to 71%, and minimum setting of 0% as indicated on the chart below. Please note that the settings are different for Normally Closed (NC) and Normally Open (NO) operation. When ordering, please specify NO or NC operation. Selecting the Proper Control Signal Select one of the MFT codes below for the signal required. Example: A 3 GPM flow rate is required, spring return actuator, 2-10 VDC signal. Solution: PICCV LF24-MFT US + P Engineering Note: The 1/2 PICCV utilizes two uniquely engineered valve bodies to achieve the listed flow rate offerings. Variable GPMs are further realized using Belimo s registered Multi- Function Technology. The PICCV offers nominal flow rates that are adjustable from 0.5 to 1.3 GPM. The PICCV offers nominal flow rates that are adjustable from 1.5 to 5.5 GPM range. Please follow MFT guideline settings when configuring the PICCV MFT actuators in the field. MFT Adjustment Table NC will open as voltage increases (no flow at 0-2V) - actuator switch on CW Default* Flow Adjustments** Flow rate Flow rate MFT angle of MFT angle of Product Range GPM l/s GPM l/s rotation max. setting rotation min. setting PICCV (-PT) + LF24-MFT US FO 72%, FC 68% FO, FC 0% NEW PICCV (-PT) + LF24-MFT US FO 91%, FC 88% FO, FC 0% NEW PICCV (-PT) + LF24-MFT US % 0% PICCV (-PT) + LF24-MFT US % 0% PICCV (-PT) + LF24-MFT US % 0% PICCV PT + LF24-MFT US % 0% % 0% PICCV (-PT) + LF24-MFT US % 0% % 0% PICCV (-PT) + LF24-MFT US % 0% % 0% PICCV (-PT) + LF24-MFT US % 0% % 0% MFT Adjustment Table NO will close as voltage increases (no flow at 10V) - actuator switch on CCW Default* Flow Adjustments** Flow rate Flow rate MFT angle of MFT angle of Product Range GPM l/s GPM l/s rotation max. setting rotation min. setting PICCV (-PT) + LF24-MFT US FO, FC 100% FO 30%, FC 33% NEW PICCV (-PT) + LF24-MFT US FO, FC 100% FO 11%, FC 15% NEW PICCV (-PT) + LF24-MFT US % 55% PICCV (-PT) + LF24-MFT US % 37% PICCV (-PT) + LF24-MFT US % 43% PICCV (-PT) + LF24-MFT US % 40% % 37% PICCV (-PT) + LF24-MFT US % 35% % 32% PICCV (-PT) + LF24-MFT US % 28% % 25% PICCV (-PT) + LF24-MFT US % 20% % 18% *Preprogrammed at factory **Customer reprogrammable using MFT PC tool / or can be factory set. FO = Fail Open, FC = Fail Closed Note: 1/2 valve has 2 disc sizes (.5 to 1 GPM) (1.5 to 5.5 GPM) For replacement or re-programming, please contact Technical Support Multi-Function Technology For complete technical information and list of configuration codes refer to Product Documentation Multi-Function Technology For Damper and Control Valve Applications Model Control Input Running Time Built-in Feedback List Price P VDC VDC No Charge P VDC VDC No Charge P sec. PWM VDC No Charge P sec. PWM VDC No Charge P sec. PWM VDC No Charge P Floating Point VDC No Charge P-10019* On/Off VDC No Charge Example: LF24-MFT US is the basic model. Add the P pre-set MFT configuration number and list price to the actuator when ordering, as needed. Note: Most popular configurations available at no additional cost. All other configurations carry a $3 list price. *Please Note: For On/Off control input, please order P and wire as on/off. 20

21 Pressure Independent Characterized Control Valve with MFT, Spring Return Actuator, P/T Ports (Optional) 3/4, 6 10 GPM The PICCV has a unique feature in that the GPM can be adjusted by adjusting the minimum and maximum settings. Selecting the Proper Flow Rate: The PICCV (-PT) can be ordered in 6 GPM to 10 GPM flow rate increments, as stated in the table below. If you wish to re-program to the values listed in the table below: Example 1: The application requires a 6 GPM flow rate. Solution: Order the PICCV Example 2: The application requires a 8.5 GPM flow rate. Solution: Order the PICCV and re-program to the below setting for 8.5 GPM. As a standard, the PICCV is available in flows of 8 GPM and 9 GPM. If you desire 8.5 GPM and have a Normally Closed (NC) valve, simply reprogram the maximum setting to 82% and minimum setting of 0% as indicated on the chart below. Please note that the settings are different for Normally Closed (NC) and Normally Open (NO) operation. When ordering, please specify NO or NC operation. Selecting the Proper Control Signal Select one of the MFT codes below for the signal required. Example: A 6 GPM flow rate is required, spring return actuator, 2-10 VDC signal. Solution: PICCV LF24-MFT US + P Engineering Note: The 3/4 PICCV utilizes a uniquely engineered valve body to achieve the listed flow rate offerings. Variable GPMs are further realized using Belimo s registered Multi-Function Technology. The PICCV offers nominal flow rates that are adjustable from 6 to 10 GPM. Please follow MFT guideline settings when configuring the PICCV MFT actuators in the field. MFT Adjustment Table NC will open as voltage increases (no flow at 0-2V) - actuator switch on CW Default* Flow Adjustments** Flow rate Flow rate MFT angle of MFT angle of Product Range GPM l/s GPM l/s rotation max. setting rotation min. setting PICCV (-PT) + LF24-MFT US % 0% % 0% PICCV (-PT) + LF24-MFT US % 0% % 0% PICCV (-PT) + LF24-MFT US % 0% % 0% PICCV (-PT) + LF24-MFT US % 0% % 0% PICCV (-PT) + LF24-MFT US % 0% MFT Adjustment Table NO will close as voltage increases (no flow at 10V) - actuator switch on CCW Default* Flow Adjustments** Flow rate Flow rate MFT angle of MFT angle of Product Range GPM l/s GPM l/s rotation max. setting rotation min. setting PICCV (-PT) + LF24-MFT US % 31% % 28% PICCV (-PT) + LF24-MFT US % 27% % 25% PICCV (-PT) + LF24-MFT US % 24% % 22% PICCV (-PT) + LF24-MFT US % 19% % 18% PICCV (-PT) + LF24-MFT US % 13% *Preprogrammed at factory **Customer reprogrammable using MFT PC tool / or can be factory set. Multi-Function Technology For complete technical information and list of configuration codes refer to Product Documentation Multi-Function Technology For Damper and Control Valve Applications Model Control Input Running Time Built-in Feedback List Price P VDC VDC No Charge P VDC VDC No Charge P sec. PWM VDC No Charge P sec. PWM VDC No Charge P sec. PWM VDC No Charge P Floating Point VDC No Charge P-10019* On/Off VDC No Charge Example: LF24-MFT US is the basic model. Add the P pre-set MFT configuration number and list price to the actuator when ordering, as needed. Note: Most popular configurations available at no additional cost. All other configurations carry a $3 list price. *Please Note: For On/Off control input, please order P and wire as on/off. 21

22 Pressure Independent Characterized Control Valve with MFT, Spring Return Actuator, P/T Ports (Optional) 1, GPM The PICCV has a unique feature in that the GPM can be adjusted by adjusting the minimum and maximum settings. Selecting the Proper Flow Rate: The PICCV (-PT) can be ordered in 11 GPM to 16 GPM flow increments, as stated in the table below. The PICCV (-PT) can be ordered in 17 GPM to 19 GPM flow rate increments, as stated in the table below. If you wish to re-program to the values listed in the table below: Example 1: The application requires a 14 GPM flow rate. Solution: Order the PICCV Example 2: The application requires a 15 GPM flow rate. Solution: Order the PICCV and re-program to the below setting for 15 GPM. As a standard, the PICCV is available in flows of 14 GPM and 16 GPM. If you desire 15 GPM and have a Normally Closed (NC) valve, simply reprogram the maximum setting to 83%, and minimum setting of 0% as indicated on the chart below. Please note that the settings are different for Normally Closed (NC) and Normally Open (NO) operation. When ordering, please specify NO or NC operation. Selecting the Proper Control Signal Select one of the MFT codes below for the signal required. Example: A 14 GPM flow rate is required, non-spring return actuator, 2-10 VDC signal. Solution: PICCV LF24-MFT US + P Engineering Note: The 1 PICCV utilizes two uniquely engineered valve bodies to achieve the listed flow rate offerings. Variable GPMs are further realized using Belimo s registered Multi-Function Technology. The PICCV offers nominal flow rates that are adjustable from 11 to 16 GPM. The PICCV offers nominal flow rates that are adjustable from 17 to 19 GPM range. Please follow MFT guideline settings when configuring the PICCV MFT actuators in the field. MFT Adjustment Table NC will open as voltage increases (no flow at 0-2V) - actuator switch on CW Default* Flow Adjustable** Flow rate Flow rate MFT angle of MFT angle of Product Range GPM l/s GPM l/s rotation max. setting rotation min. setting % 0% PICCV (-PT) + LF24-MFT US % 0% % 0% PICCV (-PT) + LF24-MFT US % 0% % 0% PICCV (-PT) + LF24-MFT US % 0% PICCV (-PT) + LF24-MFT US % 0% % 0% % 0% MFT Adjustment Table NO will close as voltage increases (no flow at 10V) - actuator switch on CCW Default* Flow Adjustable** Flow rate Flow rate MFT angle of MFT angle of Product Range GPM l/s GPM l/s rotation max. setting rotation min. setting % 26% PICCV (-PT) + LF24-MFT US % 24% % 20% PICCV (-PT) + LF24-MFT US % 16% % 9% PICCV (-PT) + LF24-MFT US % 0% PICCV (-PT) + LF24-MFT US % 22% % 15% % 11% *Preprogrammed at factory **Customer reprogrammable using MFT PC tool / or can be factory set. 1 valve has 2 disc sizes (11 to 16 GPM) (17 to 19 GPM) Multi-Function Technology For complete technical information and list of configuration codes refer to Product Documentation Multi-Function Technology For Damper and Control Valve Applications Model Control Input Running Time Built-in Feedback List Price P VDC VDC No Charge P VDC VDC No Charge P sec. PWM VDC No Charge P sec. PWM VDC No Charge P sec. PWM VDC No Charge P Floating Point VDC No Charge P-10019* On/Off VDC No Charge Example: LF24-MFT US is the basic model. Add the P pre-set MFT configuration number and list price to the actuator when ordering, as needed. Note: Most popular configurations available at no additional cost. All other configurations carry a $3 list price. *Please Note: For On/Off control input, please order P and wire as on/off. 22

23 Pressure Independent Characterized Control Valve with P/T Ports and MFT, Non-Spring Return Actuator Application: The Pressure Independent Characterized Control Valve is typically used in air handling units on heating and cooling coils, and fan coil unit heating or cooling coils. Some other common applications include unit ventilators and VAV re-heat coils. This valve is suitable for use in a hydronic system with constant or variable flow. This valve is designed with MFT functionality which facilitates the use of various control input. Valve Specifications Service chilled or hot water, 60% glycol Flow characteristic equal percentage Size 1-1/4, 1-1/2, 2 Type of end fitting female, NPT Materials: Body forged brass, nickel plated Ball chrome plated brass Stem chrome plated brass Seat O-rings Viton Seat fiberglass reinforced teflon PTFE Characterizing disc TEFZEL Packing 2 EPDM O-rings, lubricated Diaphragm polyester reinforced silicone Regulator stainless steel/brass/delrin 500 AF Spring stainless steel Pete s Plugs* (Qty 2) 1/4 brass/nortel (Standard) Pressure rating 400 PSI Media temp. range 0 F to 212 F [-18 C to 100 C] Close off pressure 200 PSI Leakage ANSI Class IV (0.01% of rated valve capacity at 50 psi differential) Flow rate 1-1/4 18 GPM [1.14 l/s], 20 GPM [1.26 l/s], 22 GPM [1.33 l/s], 24 GPM [1.51 l/s], 26 GPM [1.64 l/s] Flow rate 1-1/2 26 GPM [1.64 l/s], 28 GPM [1.77 l/s], 30 GPM [1.89 l/s], 33 GPM [2.08 l/s] Flow rate 2 33 GPM [2.08 l/s], 36 GPM [2.27 l/s], 40 GPM [2.52 l/s] Rangeability 100 : 1 Differential pressure 5 to 50 PSI range Flow accuracy (absolute) ± 5% (5 to 50 PSI) Variation due to ± 5% (5 to 50 PSI) manufacturing tolerances Hysteresis (absolute) 1% Weight of valve body 1-1/4 = 8.31 lbs 1-1/2 = 7.70 lbs 2 = 9.38 lbs *Consult page 51 and 52 for flow verification data. Tefzel and Teflon are registered trademarks of Dupont Actuator Specifications ARX24-MFT Power Supply 24 VAC ± 20% 50/60 Hz 24 VDC ± 10% Power Consumption 4 W (1.25 W) Transformer Sizing 6 VA (Class 2 power source) Electrical Connection 18 GA plenum rated cable 1/2 conduit connector 3 ft [1m] 10 ft [3m] 16 ft [5m] Overload Protection electronic throughout 0 to 95 rotation Operating Range Y 2 to 10 VDC, 4 to 20 ma (default) Variable (VDC, PWM, Floating Point, On/Off) Input Impedance 100 kω (0.1 ma), 500Ω 1500 Ω (PWM, Floating Point, On/Off) Feedback Output U 2 to 10 VDC, 0.5 ma max VDC Variable Direction of Rotation reversible with switch Position Indication handle Manual Override external push button and handle Running Time Motor* 100 sec constant Humidity 5 to 95% RH non condensing (EN ) Ambient Temperature -22 F to +122 F [-30 C to +50 C] Storage Temperature -40 F to +176 F [-40 C to +80 C] Housing NEMA 2/IP54 Housing Material UL94-5VA Agency Listings culus acc. to UL A/-2-14, CAN/CSA E , CSA C22.2 No , CE acc. to 89/336/EEC Noise Level <45dB(A) Servicing maintenance free Quality Standard ISO 9001 Weight of Actuator 2.02 lbs [0.92 kg] *PICCV/ARX24-MFT must remain at 100 sec constant run time Rated Impulse Voltage 800V, Type of action 1, Control Pollution Degree 3. MFT 23

24 Pressure Independent Characterized Control Valve with P/T Ports and MFT, Non-Spring Return Actuator 1-1/4, GPM The PICCV has a unique feature in that the GPM can be adjusted by adjusting the minimum and maximum settings. Selecting the Proper Flow Rate: The PICCV PT can be ordered in 26 GPM to 33 GPM flow rate increments, as stated in the table below. If you wish to re-program to the values listed in the table below: Example 1: The application requires a 22 GPM flow rate. Solution: Order the PICCV PT Example 2: The application requires a 25 GPM flow rate. Solution: Order the PICCV PT and re-program to the below setting for 25 GPM. As a standard, the PICCV is available in flows of 18, 20, 22, 24 and 26 GPM. If you desire 25 GPM and have a Normally Closed (NC) valve, simply reprogram the maximum setting to 87%, and minimum setting of 0% as indicated on the chart below. Please note that the settings are different for Normally Closed (NC) and Normally Open (NO) operation. When ordering, please specify NO or NC operation. Selecting the Proper Control Signal Select one of the MFT codes below for the signal required. Example: A 22 GPM flow rate is required, non-spring return actuator, 2-10 VDC signal. Solution: PICCV PT + ARX24-MFT + P Engineering Note: The 1-1/4 PICCV utilizes a uniquely engineered valve body to achieve the listed flow rate offerings. Variable GPMs are further realized using Belimo s registered Multi-Function Technology. Please follow MFT guideline settings when configuring the PICCV MFT actuators in the field. Note: Minimum and Maximum Settings differ for the ARX24-MFT and AF24-MFT US actuators. MFT Adjustment Table NC will open as voltage increases (no flow at 0-2V) - actuator switch on Y 2 Default* Flow Adjustable** Flow rate Flow rate MFT angle of MFT angle of Product Range GPM l/s GPM l/s rotation max. setting rotation min. setting PICCV PT + ARX24-MFT % 0% % 0% PICCV PT + ARX24-MFT % 0% % 0% PICCV PT + ARX24-MFT % 0% % 0% PICCV PT + ARX24-MFT % 0% % 0% PICCV PT + ARX24-MFT % 0% MFT Adjustment Table NO will close as voltage increases (no flow at 10V) - actuator switch on Y 1 Default* Flow Adjustable** Flow rate Flow rate MFT angle of MFT angle of Product Range GPM l/s GPM l/s rotation max. setting rotation min. setting PICCV PT + ARX24-MFT % 25% % 24% PICCV PT + ARX24-MFT % 23% % 22% PICCV PT + ARX24-MFT % 19% % 18% PICCV PT + ARX24-MFT % 17% % 14% PICCV PT + ARX24-MFT % 11% * Preprogrammed at factory ** Customer reprogrammable using MFT PC tool / or can be factory set. Multi-Function Technology For complete technical information and list of configuration codes refer to Product Documentation Multi-Function Technology For Damper and Control Valve Applications Model Control Input Running Time Built-in Feedback List Price P VDC VDC No Charge P VDC VDC No Charge P sec. PWM VDC No Charge P sec. PWM VDC No Charge P sec. PWM VDC No Charge P Floating Point VDC No Charge P-10019* On/Off VDC No Charge Example: ARX24-MFT is the basic model. Add the P pre-set MFT configuration number and list price to the actuator when ordering, as needed. Note: Most popular configurations available at no additional cost. All other configurations carry a $3 list price. *Please Note: For On/Off control input, please order P and wire as on/off. 24

25 Pressure Independent Characterized Control Valve with P/T Ports and MFT, Non-Spring Return Actuator 1-1/2, GPM The PICCV has a unique feature in that the GPM can be adjusted by adjusting the minimum and maximum settings. Selecting the Proper Flow Rate: The PICCV PT can be ordered in 26 GPM to 33 GPM flow rate increments, as stated in the table below. If you wish to re-program to the values listed in the table below: Example 1: The application requires a 28 GPM flow rate. Solution: Order the PICCV PT Example 2: The application requires a 31 GPM flow rate. Solution: Order the PICCV PT and re-program to the below setting for 31 GPM. As a standard, the PICCV is available in flows of 26, 28, 30, and 33 GPM. If you desire 31 GPM and have a Normally Closed (NC) valve, simply reprogram the maximum setting to 89%, and minimum setting of 0% as indicated on the chart below. Please note that the settings are different for Normally Closed (NC) and Normally Open (NO) operation. When ordering, please specify NO or NC operation. Selecting the Proper Control Signal Select one of the MFT codes below for the signal required. Example: A 26 GPM flow rate is required, non-spring return actuator, 2-10 VDC signal. Solution: PICCV PT + ARX24-MFT + P Engineering Note: The 1-1/2 PICCV utilizes a uniquely engineered valve body to achieve the listed flow rate offerings. Variable GPMs are further realized using Belimo s registered Multi-Function Technology. Please follow MFT guideline settings when configuring the PICCV MFT actuators in the field. Note: Minimum and Maximum Settings differ for the ARX24-MFT and AF24-MFT US actuators. MFT Adjustment Table NC will open as voltage increases (no flow at 0-2V) - actuator switch on Y 2 Default* Flow Adjustable** Flow rate Flow rate MFT angle of MFT angle of Product Range GPM l/s GPM l/s rotation max. setting rotation min. setting PICCV PT + ARX24-MFT % 0% % 0% PICCV PT + ARX24-MFT % 0% % 0% PICCV PT + ARX24-MFT % 0% % 0% % 0% PICCV PT + ARX24-MFT % 0% MFT Adjustment Table NO will close as voltage increases (no flow at 10V) - actuator switch on Y 1 Default* Flow Adjustable** Flow rate Flow rate MFT angle of MFT angle of Product Range GPM l/s GPM l/s rotation max. setting rotation min. setting PICCV PT + ARX24-MFT % 25% % 24% PICCV PT + ARX24-MFT % 22% % 20% PICCV PT + ARX24-MFT % 16% % 12% % 10% PICCV PT + ARX24-MFT % 6% * Preprogrammed at factory ** Customer reprogrammable using MFT PC tool / or can be factory set. Multi-Function Technology For complete technical information and list of configuration codes refer to Product Documentation Multi-Function Technology For Damper and Control Valve Applications Model Control Input Running Time Built-in Feedback List Price P VDC VDC No Charge P VDC VDC No Charge P sec. PWM VDC No Charge P sec. PWM VDC No Charge P sec. PWM VDC No Charge P Floating Point VDC No Charge P-10019* On/Off VDC No Charge Example: ARX24-MFT is the basic model. Add the P pre-set MFT configuration number and list price to the actuator when ordering, as needed. Note: Most popular configurations available at no additional cost. All other configurations carry a $3 list price. *Please Note: For On/Off control input, please order P and wire as on/off. 25

26 Pressure Independent Characterized Control Valve with P/T Ports and MFT, Non-Spring Return Actuator 2, GPM The PICCV has a unique feature in that the GPM can be adjusted by adjusting the minimum and maximum settings. Selecting the Proper Flow Rate: The PICCV PT can be ordered in 33 GPM to 40 GPM flow rate increments, as stated in the table below. If you wish to re-program to the values listed in the table below: Example 1: The application requires a 33 GPM flow rate. Solution: Order the PICCV PT Example 2: The application requires a 34 GPM flow rate. Solution: Order the PICCV PT and re-program to the below setting for 34 GPM. As a standard, the PICCV is available in flows of 33 GPM and 36 GPM. If you desire 34 GPM and have a Normally Closed (NC) valve, simply re-program the maximum setting to 79%, and a minimum setting of 0% as indicated on the chart below. Please note that the settings are different for Normally Closed (NC) and Normally Open (NO) operation. When ordering, please specify NO or NC operation. Selecting the Proper Control Signal: Select one of the MFT codes below for the signal required. Example: A 33 GPM, flow rate is required, non-spring return actuator, 2-10 VDC signal. Solution: PICCV PT + ARX24-MFT + P Engineering Note: The 2" PICCV utilizes a uniquely engineered valve body to achieve the listed flow rate offerings. Variable GPMs are further realized using Belimo s registered Multi-Function Technology. The PICCV PT offers nominal flow rates that are adjustable from 33 to 40 GPM. Please follow MFT guideline settings when configuring the PICCV MFT actuators in the field. Note: Minimum and Maximum Settings differ for the ARX24-MFT and AF24-MFT US actuators. MFT Adjustment Table NC will open as voltage increases (no flow at 0-2V) - actuator switch on Y 2 Default* Flow Adjustable** Flow rate Flow rate MFT angle of MFT angle of Product Range GPM l/s GPM l/s rotation max. setting rotation min. setting PICCV PT + ARX24-MFT % 0% % 0% % 0% PICCV PT + ARX24-MFT % 0% % 0% % 0% % 0% PICCV PT + ARX24-MFT % 0% MFT Adjustment Table NO will close as voltage increases (no flow at 10V) - actuator switch on Y 1 Default* Flow Adjustable** Flow rate Flow rate MFT angle of MFT angle of Product Range GPM l/s GPM l/s rotation max. setting rotation min. setting PICCV PT + ARX24-MFT % 23% % 22% % 20% PICCV PT + ARX24-MFT % 19% % 18% % 17% % 16% PICCV PT + ARX24-MFT % 15% *Preprogrammed at factory **Customer reprogrammable using MFT PC tool / or can be factory set. Multi-Function Technology For complete technical information and list of configuration codes refer to Product Documentation Multi-Function Technology For Damper and Control Valve Applications Model Control Input Running Time Built-in Feedback List Price P VDC VDC No Charge P VDC VDC No Charge P sec. PWM VDC No Charge P sec. PWM VDC No Charge P sec. PWM VDC No Charge P Floating Point VDC No Charge P-10019* On/Off VDC No Charge Example: ARX24-MFT is the basic model. Add the P pre-set MFT configuration number and list price to the actuator when ordering, as needed. Note: Most popular configurations available at no additional cost. All other configurations carry a $3 list price. *Please Note: For On/Off control input, please order P and wire as on/off. 26

27 Pressure Independent Characterized Control Valve with P/T Ports and MFT, Spring Return Actuator Application: The Pressure Independent Characterized Control Valve is typically used in air handling units on heating and cooling coils, and fan coil unit heating or cooling coils. Some other common applications include unit ventilators and VAV re-heat coils. This valve is suitable for use in a hydronic system with constant or variable flow. This valve is designed with MFT functionality which facilitates the use of various control input. Valve Specifications Service chilled or hot water, 60% glycol Flow characteristic equal percentage Size 1-1/4, 1-1/2, 2 Type of end fitting female, NPT Materials: Body forged brass, nickel plated Ball chrome plated brass Stem chrome plated brass Seat O-rings Viton Seat fiberglass reinforced teflon PTFE Characterizing disc TEFZEL Packing 2 EPDM O-rings, lubricated Diaphragm polyester reinforced silicone Regulator stainless steel/brass/delrin 500 AF Spring stainless steel Pete s Plugs* (Qty 2) 1/4 brass/nortel (Standard) Pressure rating 400 PSI Media temp. range 0 F to 212 F [-18 C to 100 C] Close off pressure 200 PSI Leakage ANSI Class IV (0.01% of rated valve capacity at 50 psi differential) Flow rate 1-1/4 18 GPM [1.14 l/s], 20 GPM [1.26 l/s], 22 GPM [1.33 l/s], 24 GPM [1.51 l/s], 26 GPM [1.64 l/s] Flow rate 1-1/2 26 GPM [1.64 l/s], 28 GPM [1.77 l/s], 30 GPM [1.89 l/s], 33 GPM [2.08 l/s] Flow rate 2 33 GPM [2.08 l/s], 36 GPM [2.27 l/s], 40 GPM [2.52 l/s] Rangeability 100 : 1 Differential pressure 5 to 50 PSI range Flow accuracy (absolute) ± 5% (5 to 50 PSI) Variation due to ± 5% (5 to 50 PSI) manufacturing tolerances Hysteresis (absolute) 1% Weight of valve body Weight of valve body 1-1/4 = 8.31 lbs, 1-1/2 = 7.70 lbs 2 = 9.38 lbs *Consult page 51 and 52 for flow verification data. Tefzel and Teflon are registered trademarks of Dupont Actuator Specifications AF24-MFT US Control MFT Control signal: 2 to 10 VDC, (4 to 20 ma with 500Ω resistor) Power supply 24 VAC ± 20% 50/60 Hz 24 VDC ± 10% Power consumption: 6 W running, 2.5 W holding Transformer sizing: 10 VA, class 2 power Electrical connection: 3 ft, 18 GA appl. cable, 1/2 conduit fit. Electrical protection: Aux. switches double insulated Overload protection: electronic throughout rotation Input impedance: 100 KΩ for 2 to 10 VDC (0.1 ma) 500Ω for 4 to 20 ma 750Ω for PWM 1500Ω for on/off and floating point Feedback output: 2 to 10 VDC, 0.5 ma max Angle of rotation: 95 Direction of rotation: selected by switch: CW=CW with decrease signal CCW=CCW with decrease signal Spring return direction: CW/CCW mounting Position indication: visual indicator Manual override: hex crank Running time motor:* 100 sec constant Ambient temperature: -22 F to 122 F [-30 C to 50 C] Housing: NEMA 2 / IP54 Agency listings: UL 873, CSA C22.2 No. 24 certified, CE Noise level: max. 45 db(a) AF24-MFT-S US Auxiliary switch 2 x SPDT 5 fixed/25 to 85, 7A 250 VAC Weight of actuator 6.28 lbs [2.85 Kg] *PICCV/AF24-MFT US must remain at 100 sec constant run time 27

28 Pressure Independent Characterized Control Valve with P/T Ports and MFT, Spring Return Actuator 1-1/4, GPM The PICCV has a unique feature in that the GPM can be adjusted by adjusting the minimum and maximum settings. Selecting the Proper Flow Rate: The PICCV PT can be ordered in 18 GPM to 26 GPM flow rate increments, as stated in the table below. If you wish to re-program to the values listed in the table below: Example 1: The application requires a 22 GPM flow rate. Solution: Order the PICCV PT Example 2: The application requires a 25 GPM flow rate. Solution: Order the PICCV PT and re-program to the below setting for 25 GPM. As a standard, the PICCV is available in flows of 18, 20, 22, 24 and 26 GPM. If you desire 25 GPM and have a Normally Closed (NC) valve, simply reprogram the maximum setting to 87%, and minimum setting of 0% as indicated on the chart below. Please note that the settings are different for Normally Closed (NC) and Normally Open (NO) operation. When ordering, please specify NO or NC operation. Selecting the Proper Control Signal Select one of the MFT codes below for the signal required. Example: A 22 GPM flow rate is required, non-spring return actuator, 2-10 VDC signal. Solution: PICCV PT + AF24-MFT US + P Engineering Note: The 1-1/4 PICCV utilizes a uniquely engineered valve body to achieve the listed flow rate offerings. Variable GPMs are further realized using Belimo s registered Multi-Function Technology. Please follow MFT guideline settings when configuring the PICCV MFT actuators in the field. Note: Minimum and Maximum Settings differ for the ARX24-MFT and AF24-MFT US actuators. MFT Adjustment Table NC will open as voltage increases (no flow at 0-2V) - actuator switch on CW Default* Flow Adjustable** Flow rate Flow rate MFT angle of MFT angle of Product Range GPM l/s GPM l/s rotation max. setting rotation min. setting PICCV PT + AF24-MFT US % 0% % 0% PICCV PT + AF24-MFT US % 0% % 0% PICCV PT + AF24-MFT US % 0% % 0% PICCV PT + AF24-MFT US % 0% % 0% PICCV PT + AF24-MFT US % 0% MFT Adjustment Table Multi-Function Technology NO will close as voltage increases (no flow at 10V) - actuator switch on CCW Default* Flow Adjustable** Flow rate Flow rate MFT angle of MFT angle of Product Range GPM l/s GPM l/s rotation max. setting rotation min. setting PICCV PT + AF24-MFT US % 25% % 24% PICCV PT + AF24-MFT US % 23% % 22% PICCV PT + AF24-MFT US % 19% % 18% PICCV PT + AF24-MFT US % 17% % 14% PICCV PT + AF24-MFT US % 11% * Preprogrammed at factory ** Customer reprogrammable using MFT PC tool / or can be factory set. For complete technical information and list of configuration codes refer to Product Documentation Multi-Function Technology For Damper and Control Valve Applications Model Control Input Running Time Built-in Feedback List Price P VDC VDC No Charge P VDC VDC No Charge P sec. PWM VDC No Charge P sec. PWM VDC No Charge P sec. PWM VDC No Charge P Floating Point VDC No Charge P-10019* On/Off VDC No Charge Example: AF24-MFT US is the basic model. Add the P pre-set MFT configuration number and list price to the actuator when ordering, as needed. Note: Most popular configurations available at no additional cost. All other configurations carry a $3 list price. *Please Note: For On/Off control input, please order P and wire as on/off. 28

29 Pressure Independent Characterized Control Valve with P/T Ports and MFT, Spring Return Actuator 1-1/2, GPM The PICCV has a unique feature in that the GPM can be adjusted by adjusting the minimum and maximum settings. Selecting the Proper Flow Rate: The PICCV PT can be ordered in 26 GPM to 33 GPM flow rate increments, as stated in the table below. If you wish to re-program to the values listed in the table below: Example 1: The application requires a 28 GPM flow rate. Solution: Order the PICCV PT Example 2: The application requires a 31 GPM flow rate. Solution: Order the PICCV PT and re-program to the below setting for 31 GPM. As a standard, the PICCV is available in flows of 26, 28, 30, and 33 GPM. If you desire 31 GPM and have a Normally Closed (NC) valve, simply reprogram the maximum setting to 89%, and minimum setting of 0% as indicated on the chart below. Please note that the settings are different for Normally Closed (NC) and Normally Open (NO) operation. When ordering, please specify NO or NC operation. Selecting the Proper Control Signal Select one of the MFT codes below for the signal required. Example: A 26 GPM flow rate is required, non-spring return actuator, 2-10 VDC signal. Solution: PICCV PT + AF24-MFT US + P Engineering Note: The 1-1/2 PICCV utilizes a uniquely engineered valve body to achieve the listed flow rate offerings. Variable GPMs are further realized using Belimo s registered Multi-Function Technology. Please follow MFT guideline settings when configuring the PICCV MFT actuators in the field. Note: Minimum and Maximum Settings differ for the ARX24-MFT and AF24-MFT US actuators. MFT Adjustment Table NC will open as voltage increases (no flow at 0-2V) - actuator switch on CW Default* Flow Adjustable** Flow rate Flow rate MFT angle of MFT angle of Product Range GPM l/s GPM l/s rotation max. setting rotation min. setting PICCV PT + AF24-MFT US % 0% % 0% PICCV PT + AF24-MFT US % 0% % 0% PICCV PT + AF24-MFT US % 0% % 0% % 0% PICCV PT + AF24-MFT US % 0% MFT Adjustment Table NO will close as voltage increases (no flow at 10V) - actuator switch on CCW Default* Flow Adjustable** Flow rate Flow rate MFT angle of MFT angle of Product Range GPM l/s GPM l/s rotation max. setting rotation min. setting PICCV PT + AF24-MFT US % 25% % 24% PICCV PT + AF24-MFT US % 22% % 20% PICCV PT + AF24-MFT US % 16% % 12% % 10% PICCV PT + AF24-MFT US % 6% * Preprogrammed at factory ** Customer reprogrammable using MFT PC tool / or can be factory set. Multi-Function Technology For complete technical information and list of configuration codes refer to Product Documentation Multi-Function Technology For Damper and Control Valve Applications Model Control Input Running Time Built-in Feedback List Price P VDC VDC No Charge P VDC VDC No Charge P sec. PWM VDC No Charge P sec. PWM VDC No Charge P sec. PWM VDC No Charge P Floating Point VDC No Charge P-10019* On/Off VDC No Charge Example: AF24-MFT US is the basic model. Add the P pre-set MFT configuration number and list price to the actuator when ordering, as needed. Note: Most popular configurations available at no additional cost. All other configurations carry a $3 list price. *Please Note: For On/Off control input, please order P and wire as on/off. 29

30 Pressure Independent Characterized Control Valve with P/T Ports and MFT, Spring Return Actuator 2, GPM The PICCV has a unique feature in that the GPM can be adjusted by adjusting the minimum and maximum settings. Selecting the Proper Flow Rate: The PICCV PT can be ordered in 33 GPM to 40 GPM flow rate increments, as stated in the table below. If you wish to re-program to the values listed in the table below: Example 1: The application requires a 33 GPM flow rate. Solution: Order the PICCV PT Example 2: The application requires a 34 GPM flow rate. Solution: Order the PICCV PT and re-program to the below setting for 34 GPM. As a standard, the PICCV is available in flows of 33 GPM and 36 GPM. If you desire 34 GPM and have a Normally Closed (NC) valve, simply re-program the maximum setting to 79%, and a minimum setting of 0% as indicated on the chart below. Please note that the settings are different for Normally Closed (NC) and Normally Open (NO) operation. When ordering, please specify NO or NC operation. Selecting the Proper Control Signal: Select one of the MFT codes below for the signal required. Example: A 33 GPM, flow rate is required, non-spring return actuator, 2-10 VDC signal. Solution: PICCV PT + AF24-MFT US + P Engineering Note: The 2" PICCV utilizes a uniquely engineered valve body to achieve the listed flow rate offerings. Variable GPMs are further realized using Belimo s registered Multi-Function Technology. The PICCV PT offers nominal flow rates that are adjustable from 33 to 40 GPM. Please follow MFT guideline settings when configuring the PICCV MFT actuators in the field. Note: Minimum and Maximum Settings differ for the ARX24-MFT and AF24-MFT US actuators. MFT Adjustment Table NC will open as voltage increases (no flow at 0-2V) - actuator switch on CW Default* Flow Adjustable** Flow rate Flow rate MFT angle of MFT angle of Product Range GPM l/s GPM l/s rotation max. setting rotation min. setting PICCV PT + AF24-MFT US % 0% % 0% % 0% PICCV PT + AF24-MFT US % 0% % 0% % 0% % 0% PICCV PT + AF24-MFT US % 0% MFT Adjustment Table NO will close as voltage increases (no flow at 10V) - actuator switch on CCW Default* Flow Adjustable** Flow rate Flow rate MFT angle of MFT angle of Product Range GPM l/s GPM l/s rotation max. setting rotation min. setting PICCV PT + AF24-MFT US % 23% % 22% % 20% PICCV PT + AF24-MFT US % 19% % 18% % 17% % 16% PICCV PT + AF24-MFT US % 15% *Preprogrammed at factory Multi-Function Technology **Customer reprogrammable using MFT PC tool / or can be factory set. For complete technical information and list of configuration codes refer to Product Documentation Multi-Function Technology For Damper and Control Valve Applications Model Control Input Running Time Built-in Feedback List Price P VDC VDC No Charge P VDC VDC No Charge P sec. PWM VDC No Charge P sec. PWM VDC No Charge P sec. PWM VDC No Charge P Floating Point VDC No Charge P-10019* On/Off VDC No Charge Example:AF24-MFT US is the basic model. Add the P pre-set MFT configuration number and list price to the actuator when ordering, as needed. Note: Most popular configurations available at no additional cost. All other configurations carry a $3 list price. *Please Note: For On/Off control input, please order P and wire as on/off. 30

31 2 Pressure Independent Characterized Control Valve with P/T Ports and MFT, Non-Spring Return Actuator Application: The Pressure Independent Characterized Control Valve is typically used in air handling units on heating and cooling coils, and fan coil unit heating or cooling coils. Some other common applications include unit ventilators and VAV re-heat coils. This valve is suitable for use in a hydronic system with constant or variable flow. This valve is designed with MFT functionality which facilitates the use of various control input. Valve Specifications Service Flow characteristic Size Type of end fitting Materials: Body Ball Stem Seat O-rings Seats Characterizing disc Packing Diaphragm Regulator components Spring Pete s Plugs* Qty (2) Body pressure rating Media temp. range chilled or hot water, 60% glycol equal percentage 2 (44 GPM to 100 GPM) female, NPT forged brass, nickel plated chrome plated brass chrome plated brass Viton fiberglass reinforced teflon PTFE TEFZEL 2 EPDM O-rings, lubricated polyester reinforced silicone stainless steel/brass/delrin 500 AF stainless steel 1/4 brass/nortel (Standard) 400 PSI 0 F to 212 F [-18 C to 100 C] Close off pressure 200 PSI Leakage ANSI Class IV (0.01% of rated valve capacity at 50 psi differential) Flow rate 2 44 GPM [2.78 l/s], 48 GPM [3.03 l/s], 52 GPM [3.28 l/s], 56 GPM [3.53 l/s], 60 GPM [3.79 l/s], 65 GPM [4.10 l/s], 70 GPM [4.42 l/s], 75 GPM [4.73 l/s], 80 GPM [5.05 l/s], 90 GPM [5.68 l/s], 100 GPM [6.31 l/s] Rangeability 100 : 1 Differential pressure 5 to 50 PSI range Flow accuracy (absolute) ± 5% (5 to 50 PSI) Variation due to ± 5% (5 to 50 PSI) manufacturing tolerances Hysteresis (absolute) 1% Weight of valve body 29.1 lbs Tefzel and Teflon are registered trademarks of Dupont *Consult page 51 and 52 for flow verification data. Actuator Specifications ARX24-MFT Power Supply 24 VAC ± 20% 50/60 Hz 24 VDC ± 10% Power Consumption 4 W (1.25 W) Transformer Sizing 6 VA (Class 2 power source) Electrical Connection 18 GA plenum rated cable 1/2 conduit connector 3 ft [1m] 10 ft [3m] 16 ft [5m] Overload Protection electronic throughout 0 to 95 rotation Operating Range Y 2 to 10 VDC, 4 to 20 ma (default) Variable (VDC, PWM, Floating Point, On/Off) Input Impedance 100 kω (0.1 ma), 500Ω 1500 Ω (PWM, Floating Point, On/Off) Feedback Output U 2 to 10 VDC, 0.5 ma max VDC Variable Direction of Rotation reversible with switch Position Indication handle Manual Override external push button and handle Running time motor* 100 sec constant Humidity 5 to 95% RH non condensing (EN ) Ambient Temperature -22 F to +122 F [-30 C to +50 C] Storage Temperature -40 F to +176 F [-40 C to +80 C] Housing NEMA 2/IP54 Housing Material UL94-5VA Agency Listings culus acc. to UL A/-2-14, CAN/CSA E , CSA C22.2 No , CE acc. to 89/336/EEC Noise Level <45dB(A) Servicing maintenance free Quality Standard ISO 9001 Weight of actuator 2.02 lbs [0.92 kg] *PICCV/ARX24-MFT US must remain at 100 sec constant run time Rated Impulse Voltage 800V, Type of action 1, Control Pollution Degree 3. LISTED 94D5 TEMP. IND & REG. EQUIP. UL MFT 31

32 2 Pressure Independent Characterized Control Valve with P/T Ports and MFT, Non-Spring Return Actuator 2, GPM The PICCV has a unique feature in that the GPM can be adjusted by adjusting the minimum and maximum settings. Selecting the Proper Flow Rate: The PICCV PT can be ordered in 44 GPM to 80 GPM flow rate increments, as stated in the table below. If you wish to re-program to the values listed in the table below: Example 1: The application requires a 50 GPM flow rate, and a Normally Closed valve. Solution: Order the PICCV PT Example 2: The application requires a 56 GPM flow rate. Solution: Order the PICCV PT and re-program to a maximum setting of 87%, and a minimum setting of 0% as indicated on the chart below. Please note that the settings are different for Normally Closed (NC) and Normally Open (NO) operation. When ordering, please specify NO or NC operation. Selecting the Proper Control Signal: Select one of the MFT codes below for the signal required. Example: A 50 GPM, flow rate is required, non-spring return actuator, 2-10 VDC signal. Solution: PICCV PT + ARX24-MFT + P Engineering Note: The 2" PICCV utilizes a uniquely engineered valve body to achieve the listed flow rate offerings. Variable GPMs are further realized using Belimo s registered Multi-Function Technology. The PICCV PT offers nominal flow rates that are adjustable from 44 to 80 GPM. Please follow MFT guideline settings when configuring the PICCV MFT actuators in the field. Note: Minimum and Maximum Settings differ for the ARX24-MFT and AF24-MFT US actuators. MFT Adjustment Table NC will open as voltage increases (no flow at 0-2V) - actuator switch on Y 2 Default* Flow rate MFT angle of MFT angle of Product Range GPM l/s rotation max. setting rotation min. setting PICCV PT + ARX24-MFT % 0% PICCV PT + ARX24-MFT % 0% PICCV PT + ARX24-MFT % 0% PICCV PT + ARX24-MFT % 0% PICCV PT + ARX24-MFT % 0% PICCV PT + ARX24-MFT % 0% PICCV PT + ARX24-MFT % 0% PICCV PT + ARX24-MFT % 0% PICCV PT + ARX24-MFT % 0% PICCV PT + ARX24-MFT % 0% PICCV PT + ARX24-MFT % 0% MFT Adjustment Table NO will close as voltage increases (no flow at 10V) - actuator switch on Y 1 Default* Flow rate MFT angle of MFT angle of Product Range GPM l/s rotation max. setting rotation min. setting PICCV PT + ARX24-MFT % 28% PICCV PT + ARX24-MFT % 26% PICCV PT + ARX24-MFT % 24% PICCV PT + ARX24-MFT % 22% PICCV PT + ARX24-MFT % 20% PICCV PT + ARX24-MFT % 17% PICCV PT + ARX24-MFT % 13% PICCV PT + ARX24-MFT % 10% PICCV PT + ARX24-MFT % 1% PICCV PT + ARX24-MFT % 11% PICCV PT + ARX24-MFT % 0% *Preprogrammed at factory **Customer reprogrammable using MFT PC tool / or can be factory set. Note: 2 valves has 2 disc sizes (44 GPM to 80 GPM) (90 GPM to 100 GPM) Multi-Function Technology For complete technical information and list of configuration codes refer to Product Documentation Multi-Function Technology For Damper and Control Valve Applications Model Control Input Running Time Built-in Feedback List Price P VDC VDC No Charge P VDC VDC No Charge P sec. PWM VDC No Charge P sec. PWM VDC No Charge P sec. PWM VDC No Charge P Floating Point VDC No Charge P-10019* On/Off VDC No Charge Example: ARX24-MFT is the basic model. Add the P pre-set MFT configuration number and list price to the actuator when ordering, as needed. Note: Most popular configurations available at no additional cost. All other configurations carry a $3 list price. *Please Note: For On/Off control input, please order P and wire as on/off. 32

33 2 Pressure Independent Characterized Control Valve with P/T Ports and MFT, Spring Return Actuator Application: The Pressure Independent Characterized Control Valve is typically used in air handling units on heating and cooling coils, and fan coil unit heating or cooling coils. Some other common applications include unit ventilators and VAV re-heat coils. This valve is suitable for use in a hydronic system with constant or variable flow. This valve is designed with MFT functionality which facilitates the use of various control input. Valve Specifications Service chilled or hot water, 60% glycol Flow characteristic equal percentage Size 2 (44 GPM GPM) Type of end fitting female, NPT Materials: Body forged brass, nickel plated Ball chrome plated brass Stem chrome plated brass Seat O-rings Viton Seats fiberglass reinforced teflon PTFE Characterizing disc TEFZEL Packing 2 EPDM O-rings, lubricated Diaphragm polyester reinforced silicone Regulator components stainless steel/brass/delrin 500 AF Spring stainless steel Pete s Plugs* (Qty 2) 1/4 brass/nortel (Standard) Body pressure rating 400 PSI Media temp. range 0 F to 212 F [-18 C to 100 C] Close off pressure 200 PSI Leakage ANSI Class IV (0.01% of rated valve capacity at 50 psi differential) Flow rate 2 44 GPM [2.78 l/s], 48 GPM [3.03 l/s], 52 GPM [3.28 l/s], 56 GPM [3.53 l/s], 60 GPM [3.79 l/s], 65 GPM [4.10 l/s], 70 GPM [4.42 l/s], 75 GPM [4.73 l/s], 80 GPM [5.05 l/s], 90 GPM [5.68 l/s], 100 GPM [6.31 l/s] Rangeability 100 : 1 Differential pressure 5 to 50 PSI range Flow accuracy (absolute) ± 5% (5 to 50 PSI) Variation due to ± 5% (5 to 50 PSI) manufacturing tolerances Hysteresis (absolute) 1% Weight of valve body 29.1 lbs Tefzel and Teflon are registered trademarks of Dupont *Consult page 51 and 52 for flow verification data. Actuator Specifications AF24-MFT US Control Control signal: Power supply Power consumption: Transformer sizing: Electrical connection: Electrical protection: MFT 2 to 10 VDC, (4 to 20 ma with 500Ω resistor) 24 VAC ± 20% 50/60 Hz 24 VDC ± 10% 6 W running, 2.5 W holding 10 VA, class 2 power 3 ft, 18 GA appl. cable, 1/2 conduit fit. Aux. switches double insulated Overload protection: electronic throughout rotation Input impedance: 100 KΩ for 2 to 10 VDC (0.1 ma) 500Ω for 4 to 20 ma 750Ω for PWM 1500Ω for on/off and floating point Feedback output: 2 to 10 VDC, 0.5 ma max Angle of rotation: 95 Direction of rotation: selected by switch: CW=CW with decrease signal CCW=CCW with decrease signal Spring return direction: CW/CCW mounting Position indication: visual indicator Manual override: hex crank Auxiliary switches: 2 x SPDT. 5 fixed/25 to 85 (-S) Running time motor:* 100 sec constant Ambient temperature: -22 F to 122 F [-30 C to 50 C] Housing: NEMA 2 / IP54 Agency listings: UL 873, CSA C22.2 No. 24 certified, CE Noise level: max. 45 db(a) AF24-MFT-S US Auxiliary switch 2 x SPDT 5 fixed/25 to 85, 7A 250 VAC Weight of actuator 6.28 lbs [2.85 Kg] *PICCV/AF24-MFT US must remain at 100 sec constant run time LISTED 94D5 TEMP. IND & REG. EQUIP. UL MFT 33

34 2 Pressure Independent Characterized Control Valve with P/T Ports and MFT, Spring Return Actuator 2, GPM The PICCV has a unique feature in that the GPM can be adjusted by adjusting the minimum and maximum settings. Selecting the Proper Flow Rate: The PICCV PT can be ordered in 44 GPM to 80 GPM flow rate increments, as stated in the table below. If you wish to re-program to the values listed in the table below: Example 1: The application requires a 50 GPM flow rate, and a Normally Closed valve. Solution: Order the PICCV PT Example 2: The application requires a 56 GPM flow rate. Solution: Order the PICCV PT and re-program to a maximum setting of 81%, and a minimum setting of 0% as indicated on the chart below. Please note that the settings are different for Normally Closed (NC) and Normally Open (NO) operation. When ordering, please specify NO or NC operation. Selecting the Proper Control Signal: Select one of the MFT codes below for the signal required. Example: A 50 GPM, flow rate is required, spring return actuator, 2-10 VDC signal. Solution: PICCV PT + AF24-MFT US + P Engineering Note: The 2" PICCV utilizes a uniquely engineered valve body to achieve the listed flow rate offerings. Variable GPMs are further realized using Belimo s registered Multi-Function Technology. The PICCV PT offers nominal flow rates that are adjustable from 44 to 80 GPM. Please follow MFT guideline settings when configuring the PICCV MFT actuators in the field. Note: Minimum and Maximum Settings differ for the ARX24-MFT and AF24-MFT US actuators. MFT Adjustment Table NC will open as voltage increases (no flow at 0-2V) - actuator switch on CW Default* Flow rate MFT angle of MFT angle of Product Range GPM l/s rotation max. setting rotation min. setting PICCV PT + AF24-MFT US % 0% PICCV PT + AF24-MFT US % 0% PICCV PT + AF24-MFT US % 0% PICCV PT + AF24-MFT US % 0% PICCV PT + AF24-MFT US % 0% PICCV PT + AF24-MFT US % 0% PICCV PT + AF24-MFT US % 0% PICCV PT + AF24-MFT US % 0% PICCV PT + AF24-MFT US % 0% PICCV PT + AF24-MFT US FO 93%, FC 89% FO, FC 0% PICCV PT + AF24-MFT US FO, FC 100% FO, FC 0% MFT Adjustment Table NO will close as voltage increases (no flow at 10V) - actuator switch on CCW Default* Flow rate MFT angle of MFT angle of Product Range GPM l/s rotation max. setting rotation min. setting PICCV PT + AF24-MFT US % 24% PICCV PT + AF24-MFT US % 22% PICCV PT + AF24-MFT US % 21% PICCV PT + AF24-MFT US % 19% PICCV PT + AF24-MFT US % 17% PICCV PT + AF24-MFT US % 13% PICCV PT + AF24-MFT US % 11% PICCV PT + AF24-MFT US % 2% PICCV PT + AF24-MFT US % 0% PICCV PT + AF24-MFT US FO, FC 100% FO 12%, FC 16% PICCV PT + AF24-MFT US FO, FC 100% FO, FC 0% *Preprogrammed at factory **Customer reprogrammable using MFT PC tool / or can be factory set. Note: 2 valves has 2 disc sizes (44 GPM to 80 GPM) (90 GPM to 100 GPM) Multi-Function Technology For complete technical information and list of configuration codes refer to Product Documentation Multi-Function Technology For Damper and Control Valve Applications Model Control Input Running Time Built-in Feedback List Price P VDC VDC No Charge P VDC VDC No Charge P sec. PWM VDC No Charge P sec. PWM VDC No Charge P sec. PWM VDC No Charge P Floating Point VDC No Charge P-10019* On/Off VDC No Charge Example: AF24-MFT US is the basic model. Add the P pre-set MFT configuration number and list price to the actuator when ordering, as needed. Note: Most popular configurations available at no additional cost. All other configurations carry a $3 list price. *Please Note: For On/Off control input, please order P and wire as on/off. 34

35 Feedback Charts for PICCVs with MFT Actuator PICCV (-PT) to PICCV (-PT) (.5 to 1 GPM) PICCV (-PT) Normally Closed PICCV (-PT) Normally Open PICCV (-PT) Normally Closed PICCV (-PT) Normally Open NEW NEW NEW NEW Note: Set point does not equal feedback on the TF24-MFT US, LF24-MFT US and AF24-MFT US. Set point does equal the feedback for the New Generation LRX24-MFT and ARX24-MFT. Please use NEW if the order was placed after July 24,

36 Feedback Charts for PICCVs with MFT Actuator PICCV (-PT) to PICCV (-PT) (1.5 to 3 GPM) PICCV (-PT) Normally Closed PICCV (-PT) Normally Open PICCV (-PT) Normally Closed PICCV (-PT) Normally Open PICCV (-PT) Normally Closed PICCV (-PT) Normally Open Note: Set point does not equal feedback on the TF24-MFT US, LF24-MFT US and AF24-MFT US. Set point does equal the feedback for the New Generation LRX24-MFT and ARX24-MFT. 36

37 Feedback Charts for PICCVs with MFT Actuator PICCV (-PT) to PICCV (-PT) (4 to 5 GPM) PICCV (-PT) Normally Closed PICCV (-PT) Normally Open PICCV (-PT) Normally Closed PICCV (-PT) Normally Open Note: Set point does not equal feedback on the TF24-MFT US, LF24-MFT US and AF24-MFT US. Set point does equal the feedback for the New Generation LRX24-MFT and ARX24-MFT. 37

38 Feedback Charts for PICCVs with MFT Actuator PICCV (-PT) to PICCV (-PT) (6 to 8 GPM) PICCV (-PT) Normally Closed PICCV (-PT) Normally Open PICCV (-PT) Normally Closed PICCV (-PT) Normally Open PICCV (-PT) Normally Closed PICCV (-PT) Normally Open Note: Set point does not equal feedback on the TF24-MFT US, LF24-MFT US and AF24-MFT US. Set point does equal the feedback for the New Generation LRX24-MFT and ARX24-MFT. 38

39 Feedback Charts for PICCVs with MFT Actuator PICCV (-PT) to PICCV (-PT) (9 to 10 GPM) PICCV (-PT) Normally Closed PICCV (-PT) Normally Open PICCV (-PT) Normally Closed PICCV (-PT) Normally Open Note: Set point does not equal feedback on the TF24-MFT US, LF24-MFT US and AF24-MFT US. Set point does equal the feedback for the New Generation LRX24-MFT and ARX24-MFT. 39

40 Feedback Charts for PICCVs with MFT Actuator PICCV (-PT) to PICCV (-PT) (12 to 14 GPM) PICCV (-PT) Normally Closed PICCV (-PT) Normally Open PICCV (-PT) Normally Closed PICCV (-PT) Normally Open Note: Set point does not equal feedback on the TF24-MFT US, LF24-MFT US and AF24-MFT US. Set point does equal the feedback for the New Generation LRX24-MFT and ARX24-MFT. 40

41 Feedback Charts for PICCVs with MFT Actuator PICCV (-PT) to PICCV (-PT) (16 to 18 GPM) PICCV (-PT) Normally Closed PICCV (-PT) Normally Open PICCV PT Normally Closed PICCV PT Normally Open Note: Set point does not equal feedback on the TF24-MFT US, LF24-MFT US and AF24-MFT US. Set point does equal the feedback for the New Generation LRX24-MFT and ARX24-MFT. 41

42 Feedback Charts for PICCVs with MFT Actuator PICCV PT to PICCV PT (18 to 22 GPM) PICCV PT Normally Closed PICCV PT Normally Open PICCV PT Normally Closed PICCV PT Normally Open PICCV PT Normally Closed PICCV PT Normally Open Note: Set point does not equal feedback on the TF24-MFT US, LF24-MFT US and AF24-MFT US. Set point does equal the feedback for the New Generation LRX24-MFT and ARX24-MFT. 42

43 Feedback Charts for PICCVs with MFT Actuator PICCV PT to PICCV PT (24 to 26 GPM) PICCV PT Normally Closed PICCV PT Normally Open PICCV PT Normally Closed PICCV PT Normally Open Note: Set point does not equal feedback on the TF24-MFT US, LF24-MFT US and AF24-MFT US. Set point does equal the feedback for the New Generation LRX24-MFT and ARX24-MFT. 43

44 Feedback Charts for PICCVs with MFT Actuator PICCV PT to PICCV PT (26 to 28 GPM) PICCV PT Normally Closed PICCV PT Normally Open PICCV PT Normally Closed PICCV PT Normally Open Note: Set point does not equal feedback on the TF24-MFT US, LF24-MFT US and AF24-MFT US. Set point does equal the feedback for the New Generation LRX24-MFT and ARX24-MFT. 44

45 Feedback Charts for PICCVs with MFT Actuator PICCV PT to PICCV PT (30 to 33 GPM) PICCV PT Normally Closed PICCV PT Normally Open PICCV PT Normally Closed PICCV PT Normally Open Note: Set point does not equal feedback on the TF24-MFT US, LF24-MFT US and AF24-MFT US. Set point does equal the feedback for the New Generation LRX24-MFT and ARX24-MFT. 45

46 Feedback Charts for PICCVs with MFT Actuator PICCV PT to PICCV PT (33 to 40 GPM) PICCV PT Normally Closed PICCV PT Normally Open PICCV PT Normally Closed PICCV PT Normally Open PICCV PT Normally Closed Note: Set point does not equal feedback on the TF24-MFT US, LF24-MFT US and AF24-MFT US. Set point does equal the feedback for the New Generation LRX24-MFT and ARX24-MFT PICCV PT Normally Open 46

47 Feedback Charts for PICCVs with MFT Actuator PICCV PT to PICCV PT (44 to 52 GPM) PICCV PT Normally Closed PICCV PT Normally Open PICCV PT Normally Closed PICCV PT Normally Open PICCV PT Normally Closed PICCV PT Normally Open Note: Set point does not equal feedback on the TF24-MFT US, LF24-MFT US and AF24-MFT US. Set point does equal the feedback for the New Generation LRX24-MFT and ARX24-MFT. 47

48 Feedback Charts for PICCVs with MFT Actuator PICCV PT to PICCV PT (56 to 65 GPM) PICCV PT Normally Closed PICCV PT Normally Open PICCV PT Normally Closed PICCV PT Normally Open PICCV PT Normally Closed PICCV PT Normally Open Note: Set point does not equal feedback on the TF24-MFT US, LF24-MFT US and AF24-MFT US. Set point does equal the feedback for the New Generation LRX24-MFT and ARX24-MFT. 48

49 Feedback Charts for PICCVs with MFT Actuator PICCV PT to PICCV PT (70 to 80 GPM) Note: Set point does not equal feedback on the TF24-MFT US, LF24-MFT US and AF24-MFT US. Set point does equal the feedback for the New Generation LRX24-MFT and ARX24-MFT. 49

50 Feedback Charts for PICCVs with MFT Actuator PICCV PT to PICCV PT (90 to 100 GPM) Note: Set point does not equal feedback on the TF24-MFT US, LF24-MFT US and AF24-MFT US. Set point does equal the feedback for the New Generation LRX24-MFT and ARX24-MFT. 50

51 Field Adjustable Flow Ranges and P/T Port Pressure Flow Data Procedure: (1) Adjust valve to its full rated GPM opening. (2) Measure pressure across P/T ports. (3) For default flow rate, compare DeltaP to chart value. P/T ports to verify flow P/T Port Pressure Flow Data Model # Flow Rate DeltaP across Valve (GPM) P/T Ports PICCV (-PT) PICCV (-PT) PICCV (-PT) NEW PICCV (-PT) NEW PICCV (-PT) PICCV (-PT) PICCV (-PT) PICCV (-PT) PICCV (-PT) Field Adjustable Flow Ranges with the LRB24-3 and FlowSetR Default Model # Flow Rate Field Adjustable Valve (GPM)* Design Flow (GPM)** PICCV (-PT) 0.5 PICCV (-PT) 1 PICCV (-PT) 1.5 PICCV (-PT) to 1.3 PICCV (-PT) to 5.5 PICCV (-PT) 4 PICCV (-PT) 5 PICCV (-PT) 6 PICCV (-PT) 7 PICCV (-PT) 8 2 to 10 PICCV (-PT) 9 PICCV (-PT) 10 PICCV (-PT) 12 PICCV (-PT) 14 2 to 16 PICCV (-PT) 16 PICCV (-PT) 18 6 to 19 *The indicated default flows are maximum flow values at 100% actuator travel. However, the PICCV maintains a steady flow at any degree of ball opening and balances the system dynamically from 0 to 100% of the heating or cooling load. **Specified accuracy not guaranteed. PICCV (-PT) PICCV (-PT) PICCV (-PT) PICCV (-PT) PICCV (-PT) PICCV (-PT) PICCV (-PT) PICCV (-PT) PICCV (-PT) PICCV PT PICCV PT PICCV PT PICCV PT PICCV PT PICCV PT PICCV PT PICCV PT PICCV PT PICCV PT PICCV PT PICCV PT PICCV PT PICCV PT PICCV PT PICCV PT PICCV PT PICCV PT PICCV PT PICCV PT PICCV PT PICCV PT PICCV PT Please use NEW readings if order was placed after July 24,

52 Field Adjustable Flow Ranges and P/T Port Pressure Flow Data for Customized Flows Procedure: (1) Adjust valve to its full rated GPM opening. (2) Measure pressure across P/T ports. (3) For default flow rate, compare DeltaP to chart value. P/T Port Pressure Flow Data Model # Flow Rate DeltaP across Valve (GPM) P/T Ports PICCV (-PT) PICCV (-PT) PICCV (-PT) PICCV (-PT) P/T ports to verify flow PICCV (-PT) PICCV (-PT) PICCV (-PT) PICCV (-PT) Field Adjustable Flow Ranges with the LRB24-3 and FlowSetR Default Model # Flow Rate Field Adjustable Valve (GPM)* Design Flow (GPM)** PICCV (-PT) 2.5 PICCV (-PT) 3.5 PICCV (-PT) to 5.5 PICCV (-PT) 5.5 PICCV (-PT) 6.5 PICCV (-PT) 7.5 PICCV (-PT) 8.5 PICCV (-PT) to 10 PICCV (-PT) 11 PICCV (-PT) 13 2 to 16 PICCV (-PT) 15 PICCV (-PT) 17 6 to 19 PICCV (-PT) 19 *The indicated default flows are maximum flow values at 100% actuator travel. However, the PICCV maintains a steady flow at any degree of ball opening and balances the system dynamically from 0 to 100% of the heating or cooling load. **Specified accuracy not guaranteed. PICCV (-PT) PICCV (-PT) PICCV (-PT) PICCV (-PT) PICCV (-PT) PICCV PT PICCV PT PICCV PT PICCV PT PICCV PT PICCV PT PICCV PT PICCV PT PICCV PT PICCV PT PICCV PT PICCV PT PICCV PT

53 Available Customized Flows and Certified Factory Calibrated Flows Customized Flows* PICCV s are available in a wide variety of the standard maximum flow rates as listed. This allows you to match the design flow rate much more accurately then it was possible with the selection of Cv-value of a conventional valve. If you want to customize the maximum flow rate of a PICCV you can do so, as noted in the increments in the table below. In an additional process we will set the PICCV to a specific flow rate to match your design flow, as noted in the table below. The smallest available increment is 0.50 GPM and the smallest flow is 0.50 GPM. Certified Factory Calibrated Flows (ZP-PICCV-CAL) Factory calibrated PICCV s will be programmed to a customized flow setting as mentioned in the opposite paragraph. Additionally, each single valve will be installed in a calibration rig to verify the flow rate with a high quality flow measurement device, calibrated to the requirements of ANSI/ISA , with traceability to NIST standards. For each PICCV calibrated you will receive a test certificate. Using this procedure allows for the highest flow accuracy in the field. Operating pressure ranges are 5-10 psi,10-30 psi, psi. Default pressure range is 5-30 psi. Expected flow accuracy ±5% (related to nominal valve flow). This service is available for the 1/2 to 1-1/4 PICCV (-PT) to PICCV PT. Available Customized Flows* Valve Size GPM Custom Flow Rates Actuator selections 1/2 2.5, 3.5, 4.5, 5.5 LRB24-3, LRCX24-3, LRX24-MFT, ARX24-MFT TF24-MFT US, LF24-MFT US, AF24-MFT US 3/4 6.5, 7.5, 8.5, 9.5 LRB24-3, LRCX24-3, LRX24-MFT, ARX24-MFT LF24-MFT US, AF24-MFT US 1 11, 13, 15, 17, 19 LRB24-3, LRCX24-3, LRX24-MFT, ARX24-MFT LF24-MFT US, AF24-MFT US 1-1/4 19, 21, 23, 25 ARX24-MFT, AF24-MFT US 1-1/2 27, 29, 31, 32 ARX24-MFT, AF24-MFT US 2 34, 35, 37, 38, 39 ARX24-MFT, AF24-MFT US *Part numbers for the valve body custom flows are noted in the charts on page 52. Actuator selections are the same as the standard offerings. ORDERING EXAMPLE 1 2 Choose the desired valve/actuator combination based on valve ratings and actuator control parameters. PICCV PT + LRX24-MFT Specify Configuration (important) Multi-Function Technology: Set-up: Tagging: Calibration Charge: P (2-10 VDC input / 2-10 VDC feedback) NC (Normally Closed) AHU ZP-PICCV-CAL PICCV LRX24-MFT+P NC+AHU+ZP-PICCV-CAL 53

54 PICCV Running Times All MFT actuators have constant running time of 100 seconds. Whether they are set for on/off, floating or proportional control, the running time remains constant. Note for Floating Point Control with LRB24-3: These actuators have a constant running time. The running time is dependent on the model number or FlowSetR position as indicated in the table below. Some DDC controllers need an adjustment of the running time, otherwise they lose the position information. In any case, we recommend a position reset once a day. Running Time (sec.) Running Time (sec.) Model # Flow Rate LRX24-MFT, ARX24-MFT Valve (GPM) LRB24-3 TF24-MFT US, LF24-MFT US, AF24-MFT US PICCV (-PT) PICCV (-PT) PICCV (-PT) PICCV (-PT) PICCV (-PT) PICCV (-PT) PICCV (-PT) PICCV (-PT) PICCV (-PT) PICCV (-PT) PICCV (-PT) PICCV (-PT) PICCV (-PT) PICCV (-PT) PICCV (-PT) PICCV (-PT) PICCV PT 18 na 100 PICCV PT 20 na 100 PICCV PT 22 na 100 PICCV PT 24 na 100 PICCV PT 26 na 100 PICCV PT 26 na 100 PICCV PT 28 na 100 PICCV PT 30 na 100 PICCV PT 33 na 100 PICCV PT 33 na 100 PICCV PT 36 na 100 PICCV PT 40 na 100 PICCV PT 44 na 100 PICCV PT 48 na 100 PICCV PT 52 na 100 PICCV PT 56 na 100 PICCV PT 60 na 100 PICCV PT 65 na 100 PICCV PT 70 na 100 PICCV PT 75 na 100 PICCV PT 80 na 100 PICCV PT 90 na 100 PICCV PT 100 na

55 PICCV Customized Flow Rate Running Times Running Time (sec.) Running Time (sec.) Model # Flow Rate LRX24-MFT, ARX24-MFT Valve (GPM) LRB24-3 TF24-MFT US, LF24-MFT US, AF24-MFT US PICCV (-PT) PICCV (-PT) PICCV (-PT) PICCV (-PT) PICCV (-PT) PICCV (-PT) PICCV (-PT) PICCV (-PT) PICCV (-PT) PICCV (-PT) PICCV (-PT) PICCV (-PT) PICCV (-PT) PICCV PT 19 na 100 PICCV PT 21 na 100 PICCV PT 23 na 100 PICCV PT 25 na 100 PICCV PT 27 na 100 PICCV PT 29 na 100 PICCV PT 31 na 100 PICCV PT 32 na 100 PICCV PT 34 na 100 PICCV PT 35 na 100 PICCV PT 37 na 100 PICCV PT 38 na 100 PICCV PT 39 na

56 Instructions for Field Adjustment of Flow and Valve Sizing and Selection Instructions for Non-Spring Actuator Utilizing the FlowSetR Non-Spring Return Actuator: LRB24-3 Default set-up: FlowSetR The factory setting corresponds to the ordered flow rate (selected from Belimo s standard product range). The valves factory setting is in open position (valve always closes in CW direction). PICCV flow can be field adjusted by using a hex tool. Therefore, the maximum flow can be increased or decreased within the valves adjustable flow range. Integrated Hex Tool To set or adjust desired maximum flow (actuator, FlowSetR and valve are connected): 1. Fully close the valve via actuator control signal or via manual override (press button and turn handle in clockwise direction). Note: The FlowSetR fixed clockwise end stop purposely prevents the actuator from returning to its full zero-degree position, eliminating excess rotation. 2. Use the integrated hex tool in the actuator lever to turn adjustment screw in plus (+) or minus (-) direction in order to move scale indicator to desired flow rate. A standard hex tool (i.e. Allen wrench) size 5/32 or 4mm can also be used to turn adjustment screw. FlowSetR Adjustable with hex tool size 5/32 [4mm] GPM 0.5 Sample scale PICCV On Floating Point actuators, the running time is constant but dependent on the overall angle of rotation. 1 Avoid disconnecting FlowSetR from actuator or valve! If necessary, refer to instruction sheet on how to install FlowSetR to valve, and actuator to FlowSetR. Sizing and Selection of PICCVs To select the proper flow rate and actuation for your application: Sizing of the Pressure Independent Characterized Control Valves is based on GPM, and there is no need to calculate Cv rating. Pressure Independent Characterized Control Valves are 2-way valves that operate between a 5-50 PSI operating range. For example: If an application requires 4 GPM: Select the valve rated for 4 GPM. In the catalog, this part number is the PICCV For example: If you wish to narrow the flow to 3.5 GPM: Narrowing the flow to 3.5 GPM can be achieved with the use of the FlowSetR if you have the LRB24-3 actuator. With the use of a 5/32" or 4 mm hex tool, the flow can be adjusted in the field. For all other MFT actuators, you may reprogram to 3.5 GPM using the PC software and following the MFT guidelines. Note: Please note that PICCV bodies have a range of flow. Consult page 51 and 52 for details. For example, the valve body PICCV can maintain flows from 0.50 GPM to 1.0 GPM, and the PICCV can maintain flows between 1.5 GPM to 5.5 GPM. There will be two Pressure/Temperature ports as a standard offering for the 1-1/4" valves and larger, and available as an option for the 1" valves and smaller. The Pressure/Temperature ports will be reflected in the part number as "PT". i.e PICCV PT + LF24-MFT US. The remaining step is to select the type of actuation, based on your requirements. Prior to ordering, please provide whether you wish to have the valve normally open or normally closed, and if spring return actuation is required, please note whether the valve is to spring open or spring closed upon power loss. For example: If your application for the above valve requires spring return, 2-10 VDC input signal, 100 sec run time and 2-10 VDC feedback signal, select LF24-MFT US and MFT programming code P

57 PICCV Test and Balance Procedure, Troubleshooting PICCV Test and Balance Procedure 1. Verify that the system is purged and filled to the proper pressure. 2. Verify pump rotation. 3. Open all valves through the building management system if the total connected load➀ matches the pump GPM. Systems with diversity must have a percent of the valves closed to match the pump GPM. 4. Test total flow by accurate method.* 5. Decrease the pump speed until a flow decrease occurs. 6. Increase the pump speed until the original flow is reestablished. 7. Record system ΔP and provide this value to the ATC contractor. 8. Perform a Practical Test to verify that the designer s intent has been met. Taking a leaving air temperature can quickly verify the operation. * Accurate Methods Calibrated circuit setters on main lines Orifice Venturi Equipment pressure drops if the components are clean Ultrasonic Flowmeter Pump curves and triple duty valves have less accuracy than the above listed items PICCV Troubleshooting 1. Is the pump on and rotating properly? 2. Is the pressure differential adequate to produce design GPM? 3. Is the water temperature at the required level? GOOD IDEAS: Install taps on at least one valve with the largest DP requirement, or near the end run or near the DP transmitter. 4. Is the PICCV installed in the right direction? 5. Is there too much diversity in the system? 6. Does the valve tag GPM match the listed design GPM? 7. Does the ATC signal stroke the valve in the right direction? 8. Are strainers plugged? 9. Is the coil installed counterflow? 10. Discharge temperature not to required rating: A. Is reset temperature high enough? B. Is air by-passing the coil? C. Are all coil areas heating/cooling uniformly? 11. Room cold complaints: A. Is there enough throw➁ to penetrate air to the occupancy level? ➁Throw is the distance discharge air is propelled in order to reach the occupant level. B. Test discharge air temperature and stratification. C. Is the building under a negative pressure? D. Is the hot water temperature at design? Resets may not be effective for reheat coils. ➀Total connected load is the summation of all terminal GPM. Often, engineers will design a pumping system for the total GPM as listed for all of the coils. Some engineers will take advantage of diversity and realize that no more than ± 80% of the valves will be calling at any one time during normal operation. For instance, if you have 100 GPM of total connected load, a pump sized for 80 GPM could be installed. In this case, if all valves open after a weekend of being closed, none of the valves will handle the design flow rate. A requirement of 20% of the valves would have to be closed to match the pump to the total connected load. 57

58 Parallel Piping the PICCV to Achieve an Increase in Flow Rate Typical Parallel Piping in Relation to The Input and Output (Scale: None) The Pressure Independent Characterized Control Valves can be be piped in a parallel orientation to achieve increased flow rates. Our PICCV valves are available in flows to 100 GPM. To achieve flows larger than this, it is recommended to connect two of these valves in parallel leading to a common manifold. To correctly operate these valves, the Belimo Multi Function Technology (MFT) will be employed to utilize one common control signal. For example, the first valve will be outfitted with an MFT actuator that will correspond to a 2-5 or 2.6 VDC signal. The second valve would be outfitted with an MFT actuator that would correspond to a 6-10 VDC signal. Therefore, through a single 2-10 VDC output, the full flow range will be achieved. The actuators will be wired in a parallel arrangement. The established configured P Codes are P for 2-5 VDC, P for 2-6 VDC, and P for 6-10 VDC. This recommended application provides the control of flows up to 200 GPM by using two valves. The top diagram details valves piped in a parallel arrangement. The bottom diagram features a typical single piping arrangement. BELIMO PICCV (TYP.) PARALLEL PIPING ARRANGEMENT FOR PICCV VALVES H/C COIL P/T PORT FLOW P/T PORT P/T PORT FLOW TEE (TYP.) AIR VENT FLOW P/T PORT P/T PORT FLOW SHUT OFF VALVE H/C COIL FLOW DRAIN Typical Piping in Relation to The Input and Output (Scale: None) AIR VENT P/T PORT FLOW FLOW BELIMO PICCV (TYP.) P/T PORT STRAINER P/T PORT UNION CONNECTION (TYP.) FLOW FLOW SHUT OFF VALVE SHUT OFF VALVE UNION CONNECTION (TYP.) FLOW DRAIN P/T PORT FLOW STRAINER FLOW SHUT OFF VALVE 58

59 Dimensions Pressure Independent Characterized Control Valve with Non-Spring Return Actuator Dimension with LRB24-3, LRX24-3 Dimensions with LRX24-MFT 2.6" [66] 6.5" [165] D " [66] 7.5" [191] D " [82] 1.69" [42] 0.78" [20] 2.34" [59.4] FlowSetR Dimensions 3.22" [82] 1.69" [42] 2.34" [59.4] C C D D E F B A E F B A Dimensions (All ratings in brackets are in millimeters.) Valve A B C D E F 1/2" NPT 4.80 [122] 4.6 [117] 4.02 [102] 2.28 [58] 1.04 [24.4] 1.3 [33] 3/4" NPT 5.25 [133] 5.03 [128] 4.22[107] 2.38 [61] 1.04 [24.4] 1.3 [33] 1" NPT 7.05 [179] 6.85 [174] 4.80 [122] 3.23 [82] 1.60 [40.6] 1.60 [40.6] Dimensions with LRB24-3, LRX24-3 with P/T Ports Dimensions (All ratings in brackets are in millimeters.) Valve A B C D E F 1/2" NPT 4.80 [122] 4.6 [117] 4.02 [102] 2.28 [58] 1.04 [24.4] 1.3 [33] 3/4" NPT 5.25 [133] 5.03 [128] 4.22 [107] 2.38 [61] 1.04 [24.4] 1.3 [33] 1" NPT 7.05 [179] 6.85 [174] 4.80 [122] 3.23 [82] 1.60 [40.6] 1.60 [40.6] Dimensions with LRX24-MFT with P/T Ports 2.6" [66] 6.5" [165] D " [66] 7.5" [191] D " [82] 1.69" [42] 2.34" [59.4] 0.78" [20] FlowSetR Dimensions 3.22" [82] 1.69" [42] 2.34" [59.4] C C D D E F Dimensions (All ratings in brackets are in millimeters.) Valve A B C D E F 1/2" NPT 5.3 [135] 4.6 [117] 5.4 [137] 3.69 [94] 1.04 [24.4] 2.60 [66] 3/4" NPT 5.8 [147] 5.03 [128] 5.7 [145] 3.69 [94] 1.04 [24.4] 2.60 [66] 1" NPT 7.05 [179] 6.85 [174] 6.05 [154] 4.0 [102] 1.60 [40.6] 2.90 [73.65] Dimensions with ARX24-MFT with P/T ports 3.46" [88] 2.5" [64] 3.3" [84] D 1.35" [35] 8.0" [203] B A C 2.49" [63.4] D158 E F Dimensions (All ratings in brackets are in millimeters.) Valve A B C D E F 1/2" NPT 5.3 [135] 4.6 [117] 5.4 [137] 3.69 [94] 1.04 [24.4] 2.60 [66] 3/4" NPT 5.8 [147] 5.03 [128] 5.7 [145] 3.69 [94] 1.04 [24.4] 2.60 [66] 1" NPT 7.05 [179] 6.85 [174] 6.05 [154] 4.0 [102] 1.60 [40.6] 2.90 [73.65] Dimensions with ARX24-MFT with P/T ports 3.46" [88] 2.5" [64] 2.49" [63.4] C D 8.0" [203] B A H 3.3" 1.35" [84] [35] BELIMO DN 50 2 G D159 E F B A E F B A Dimensions (All ratings in brackets are in millimeters.) Valve A B C D E F 1-1/4" NPT 8.75 [222] 8.75 [222] 6.62 [168] 4.33 [110] 1.77 [45] 3.03 [77] 1-1/2" NPT 8.00 [203] 8.00 [203] 6.62 [168] 4.33 [110] 1.77 [45] 3.03 [77] 2" NPT* 8.5 [216] 8.5 [216] 6.62 [168] 4.4 [112] 1.77 [45] 3.03 [77] *Flows to 40 GPM. Dimensions (All ratings in brackets are in millimeters.) Valve* A B C D E F G H 2" NPT [416.2] 15.6 [396.2] 9.38 [238.3] 6.31 [160.3] 2.65 [67.3] 3.05 [77.5] [337.1] 20.6 [523.24] 2" NPT with larger flows from 44 GPM to 100 GPM 59

60 Dimensions Pressure Independent Characterized Control Valve with Spring Return Actuator TF24-MFT US TF24-MFT US with P/T ports 3.0" [76.2] 6.28" [159.55] D " [76.2] 6.28" [159.55] D " [74.5] 2.40" [61] 2.93" [74.5] 2.40" [61] C C D D E F B A E F B A Dimensions (All ratings in brackets are in millimeters.) Valve A B C D E F 1/2" NPT 4.80 [122] 4.6 [117] 4.02 [102] 2.28 [58] 1.04 [24.4] 1.3 [33] Dimensions (All ratings in brackets are in millimeters.) Valve A B C D E F 1/2" NPT 5.3 [135] 4.6 [117] 5.4 [137] 3.69 [94] 1.04 [24.4] 2.60 [66] LF24-MFT US AF24-MFT US with P/T ports 3.78" [96] 7.64" [194] D " [98] 10.47" [266] D " [114] 2.28" [58] 3.66" [93] 2.24" [57] C C D D E F Dimensions (All ratings in brackets are in millimeters.) Valve A B C D E F 1/2" NPT 4.80 [122] 4.6 [117] 4.02 [102] 2.28 [58] 1.04 [24.4] 1.3 [33] 3/4" NPT 5.25 [133] 5.03 [128] 4.22 [107] 2.38 [61] 1.04 [24.4] 1.3 [33] 1" NPT 7.05 [179] 6.85 [174] 4.80 [122] 3.23 [82] 1.60 [40.6] 1.60 [40.6] LF24-MFT US with P/T ports 3.78" [96] 4.49" [114] D B A 7.64" [194] C 2.28" [58] D130 E F Dimensions (All ratings in brackets are in millimeters.) Valve A B C D E F 1-1/4" NPT 8.75 [222] 8.75 [222] 6.62 [168] 4.33 [110] 1.77 [45] 3.03 [77] 1-1/2" NPT 8.0 [203] 8.0 [203] 6.62 [168] 4.33 [110] 1.77 [45] 3.03 [77] 2" NPT 8.5 [216] 8.5 [216] 6.62 [168] 4.4 [112] 1.77 [45] 3.03 [77] *Flows to 40 GPM. AF24-MFT US with P/T ports 3.86" [98] 2.24" [57] C D 10.47" [266] B A H 3.66" [93] BELIMO DN 50 2 G D125 E F B A E F B A Dimensions (All ratings in brackets are in millimeters.) Valve A B C D E F 1/2" NPT 5.3 [135] 4.6 [117] 5.4 [137] 3.69 [94] 1.04 [24.4] 2.60 [66] 3/4" NPT 5.8 [147] 5.03 [128] 5.7 [145] 3.69 [94] 1.04 [24.4] 2.60 [66] 1" NPT 7.05 [179] 6.85 [174] 6.05 [154] 4.0 [102] 1.60 [40.6] 2.90 [73.65] Dimensions (All ratings in brackets are in millimeters.) Valve* A B C D E F G H 2" NPT [416.2] 15.6 [396.2] 9.38 [238.3] 6.31 [160.3] 2.65 [67.3] 3.05 [77.5] [328.2] 21.9 [556.3] 2" NPT with larger flows from 44 GPM to 100 GPM 60

61 Wiring Diagrams for LRB24-3 Actuator W431 On/Off Floating Point 1 24 VAC Transformer VAC Transformer Line Volts Blk (1) Common Red (2) + Line Volts Blk (1) Common Red (2) + a open a closed a Wht (3) + Wht (3) The indication of direction is valid for switch position 1. LRB24-3 The indication of direction is valid for switch position 1. LRB_24-3 Notes: 1 2 Provide overload protection and disconnect as required. Actuators may be connected in parallel. Power consumption and input impedance must be observed. 3 Actuators may also be powered by 24 VDC. 4 Meets culus or UL and CSA requirements without the need of an electrical ground connection. 5 Actuators with plenum rated cable do not have numbers on wires; use color codes instead. Actuators with appliance cables are numbered. 61

62 Wiring Diagrams for LRX24-MFT and ARX24-MFT Actuators Actuators: LMX, LRX, NMX, AMX, ARX, GMX24-MFT W400 Hazard Identification Warnings and Cautions appear at appropriate sections throughout this manual. Read these carefully. CAUTION Indicates a potentially hazardous situation which, if not avoided, may result in minor or moderate injury. It may also be used to alert against unsafe practices. 2 VDC/4-20 ma Equipment damage! Actuators may be connected in parallel if not mechanically mounted to the same shaft. Power consumption and input impedance must be observed. WARNING Live Electrical Components! During installation, testing, servicing and troubleshooting of this product, it maybe necessary to work with live electrical components. Have a qualified licensed electrician or other individual who has been Line Volts Control Signal 4 to 20 ma or 2 to 10 VDC 24 VAC Transformer ( ) (+) Ω 500Ω 1/4 watt properly trained in handling live electrical components perform these tasks. Failure to follow all electrical safety precautions when exposed to live electrical components could result in death or serious injury Blk (1) Common Red (2) + Hot Wht (3) Y 1 Input, 2 to 10V Grn (5) U Output, 2 to 10V CCW CW 9 3 Actuators may also be powered by 24 VDC. Actuators with plenum rated cable do not have numbers on 5 wires; use color codes instead. Actuators with appliance cables are numbered. Control signal may be pulsed from either the Hot (Source) 8 or Common (Sink) 24 VAC line. For triac sink the Common connection from the actuator 10 must be connected to the Hot connection of the controller Two Position INSTALLATION NOTES APPLICATION NOTES Meets culus or UL and CSA requirements without the need of an electrical ground connection. A 500Ω resistor converts the 4 to 20 ma control signal to 2 to 10 VDC. Contact closures A & B also can be triacs. A & B should both be closed for triac source and open for triac sink. Position feedback cannot be used with a Triac sink controller. The actuator internal common reference is not compatible. Floating Point WARNING 24 VAC Transformer Live Electrical Components! During installation, testing, Line Volts servicing and troubleshooting of this product, it maybe necessary to work with live electrical components. Have a 8 A B qualified licensed electrician or other individual who has been properly trained in handling live electrical components perform these tasks. Failure to follow all electrical safety 2 to 10 VDC Feedback Signal 9 11 CCW precautions when exposed to live electrical CW components could result in death or serious injury. A B 5 PWM WARNING Live Electrical Components! During installation, testing, servicing and troubleshooting of this product, it maybe necessary to work with live electrical components. Have a qualified licensed electrician or other individual who has been Line Volts 24 VAC Transformer (AC only) Position Feedback VDC ( ) (+) Direction of rotation switch CCW CW properly trained in handling live electrical components perform these tasks. Failure to follow all electrical safety precautions when exposed to live electrical components could result in death or serious injury. 8 A B Blk (1) Common Red (2) Hot + 10 Wht (3) Y1 Input Pnk (4) Y2 Input Org (5) U Output 2 to 10V 2 Blk (1) Common Red (2) + Hot Wht (3) Y Input Org (5) U Output WARNING Live Electrical Components! 24 VAC/DC Transformer During installation, testing, servicing and troubleshooting Line of this product, it maybe necessary Volts to work with live electrical components. Have a qualified a Position ( ) licensed electrician or other individual who has been properly Feedback VDC (+) trained in handling live electrical components perform these tasks. Failure to follow all electrical safety precautions when exposed to live electrical components could result in death or serious injury. Override control to min, mid, max, positions WARNING Live Electrical Components! During installation, testing, servicing and trouble shooting of this product, it maybe necessary to work with live electrical components. Have a qualified licensed electrician or other individual who has been properly trained in handling live electrical components perform these tasks. Failure to follow all electrical safety precautions when exposed to live electrical components could result in death or serious injury. Line Volts 24 VAC Transformer Ω Control Signal ( ) 2-10 VDC or (+) 4 to 20 ma 500Ω 1/4 watt 7 Min* Mid* Max* Normal** A B C Functions 0% 50% 100% Control mode acc. to Y Blk (1) Common Red (2) Hot Wht (3) Y Input Org (5) U Output Blk (1) Common Red (2) + Hot Wht (3) Y 1 Input, 2 to 10V a b c * Default selectable 0-100%. See Configuration Data Sheet. ** Customizable. See Configuration Data Sheet

63 Wiring Diagrams for TF24-MFT US Actuators Wiring Diagrams 24 VAC Transformer 1 Line Volts 3 Control Signal ( ) 2 to 10 VDC (+) 2 to 10 VDC Feedback Signal Standard Wiring 2 Blk (1) Common Red (2) + Hot 3 Wht (3) Y 1 Input, 2 to 10V Grn (5) U Output, 2 to 10V W VAC Transformer 1 Line Volts 3 Ω 500Ω 1/4 watt Control Signal 4 to 20 ma ( ) (+) 4 Standard Wiring 2 Blk (1) Common Red (2) + Hot 3 Wht (3) Y 1 Input, 2 to 10V Grn (5) U Output, 2 to 10V W025 CCW(L) CW(R) CCW(L) CW(R) 24 VAC Transformer 1 Line Volts 3 Control Signal ( ) A 2 2 to 10 VDC (+) A Open = 0 V Position A Closed = Normal Operation Override to zero position Blk (1) Common Red (2) + Hot Wht (3) Y 1 Input, 2 to 10V Override to zero position 24 VAC Transformer 1 Line Volts Blk (1) Common Red (2) + Hot 3 Ω 500Ω 1/4 watt 2 Control Signal ( ) 4 to 20 ma (+) 4 A Wht (3) Y 1 Input, 2 to 10V A Open = 4 ma Position A Closed = Normal Operation 24 VAC Transformer 1 Line Volts 3 Control Signal ( ) B 2 2 to 10 VDC (+) C B Closed = 10 V Position C Closed = Normal Operation 1 Line Volts 3 Override to 10 V position Ω Blk (1) Common Red (2) + Hot Wht (3) Y 1 Input, 2 to 10V Override control to min, mid, max, positions 24 VAC Transformer Control Signal ( ) 2-10 VDC or 4 to 20 ma (+) 500Ω 4 1/4 watt A B C Blk (1) Common Red (2) + Hot Wht (3) Y 1 Input, 2 to 10V Functions a b c Min* Mid* Max* Normal** 0% 50% 100% Control mode acc. to Y * Default selectable 0-100%. See Configuration Data Sheet. ** Customizable. See Configuration Data Sheet. Override to 20 ma position 24 VAC Transformer 1 Line Blk (1) Common Volts Red (2) + Hot 3 Ω 2 B Control Signal ( ) 4 to 20 ma (+) Wht (3) Y 1 Input, 2 to 10V 500Ω C 4 1/4 watt B Closed = 20 ma Position C Closed = Normal Operation 4 to 20 ma Control Signal Notes With a 4-20 ma Input, up to 4 actuators may be wired in parallel. A 2% shift in the signal is seen when using a 500Ω resistor. Power consumption must be observed. Provide overload protection and disconnect as required. Actuators may be connected in parallel if not mechanically mounted to the same shaft. Power consumption and input impedance must be observed. Actuator may also be powered by 24 VDC. ZG-R01 may be used. 2 to 10 VDC Control Signal 63

64 Wiring Diagrams for LF24-MFT US and AF24-MFT US Actuators 24 VAC Transformer 1 Line Volts 3 Control Signal ( ) 2 to 10 VDC (+) 2 to 10 VDC Feedback Signal Standard Wiring 2 Blk (1) Common Red (2) + Hot 3 Wht (3) Y 1 Input, 2 to 10V Wht (5) U Output, 2 to 10V CCW(L) CW(R) W VAC Transformer 1 Line Volts 3 Ω 500Ω 1/4 watt Control Signal 4 to 20 ma ( ) (+) 4 Standard Wiring 2 Blk (1) Common Red (2) + Hot 3 Wht (3) Y 1 Input, 2 to 10V Wht (5) U Output, 2 to 10V CCW(L) CW(R) W VAC Transformer 1 Line Volts 3 Control Signal ( ) A 2 2 to 10 VDC (+) A Open = 0 V Position A Closed = Normal Operation Override to zero position Blk (1) Common Red (2) + Hot Wht (3) Y 1 Input, 2 to 10V Override to zero position 24 VAC Transformer 1 Line Volts Blk (1) Common Red (2) + Hot 3 Ω 500Ω 1/4 watt 2 Control Signal ( ) 4 to 20 ma (+) 4 A Wht (3) Y 1 Input, 2 to 10V A Open = 4 ma Position A Closed = Normal Operation VAC Transformer 1 Line Volts 3 Control Signal ( ) B 2 2 to 10 VDC (+) C B Closed = 10 V Position C Closed = Normal Operation 1 Line Volts 3 Override to 10 V position Ω Blk (1) Common Red (2) + Hot Wht (3) Y 1 Input, 2 to 10V Override control to min, mid, max, positions 24 VAC Transformer Control Signal ( ) 2-10 VDC or 4 to 20 ma (+) 500Ω 4 1/4 watt Min* Mid* Functions 0% 50% A B C Blk (1) Common Red (2) + Hot Wht (3) Y 1 Input, 2 to 10V a b c Max* 100% Normal** Control mode acc. to Y * Default selectable 0-100%. See Configuration Data Sheet. ** Customizable. See Configuration Data Sheet. 2 to 10 VDC Control Signal Override to 20 ma position 24 VAC Transformer 1 Line Blk (1) Common Volts Red (2) + Hot 3 Ω 2 B Control Signal ( ) 4 to 20 ma (+) Wht (3) Y 1 Input, 2 to 10V 500Ω C 4 1/4 watt B Closed = 20 ma Position C Closed = Normal Operation 4 to 20 ma Control Signal With a 4-20 ma Input, up to 4 actuators may be wired in parallel. A 2% shift in the signal is seen when using a 500Ω resistor. Power consumption must be observed. Notes Provide overload protection and disconnect as required. 1 Actuators may be connected in parallel if not mechanically mounted 2 to the same shaft. Power consumption and input impedance must be observed S1 S2 S3 S4 S5 S6 NC NO NC NO to 85 Auxiliary Switch AF24-MFT-S US 4 Actuator may also be powered by 24 VDC. ZG-R01 may be used. W014 S1 NC S2 S3 NO For end position indication, interlock control, fan startup, etc., AF24-MFT-S US incorporates two built-in auxiliary switches: 2 x SPDT, 7A VAC, UL listed, one switch is fixed at +5, one is adjustable 25 to 85. LF24-MFT-S US incorporates one built-in auxiliary switch: 1 x SPDT, 6A VAC, UL listed, adjustable 0 to 95. Meets UL and CSA requirements without the need of an electrical ground connection. 5 0 to 95 Auxiliary Switch LF24-MFT-S US 6 W026

65 Pressure Independent Characterized Control Valve Heat Pump Applications Optimize Your Heat Pump Application by Using a Pressure Independent Characterized Control Valve What are the benefits? A balanced system is achieved without the need for a balancer to manually balance each circuit. Because the system is dynamic and the PICCV performs dynamic balancing, Differential Pressures are no longer an issue to be concerned with. The PICCV will maintain a constant flow at part load and during morning warm-up when all loops become critical. With the PICCV, each terminal gets the required flow, no over-flow or under-flow at this critical time. The PICCV allows a mechanic to easily commission additional circuits after the initial system is up and running, again thanks to dynamic balancing capability. The PICCV is available in flow rates from.5 GPM to 19 GPM. Choosing the right PICCV is as easy as determining the appropriate flow for your heat pump and then choosing the valve that satisfies the flow requirement. How does it work? Keep with the same idea of a conventional heat pump system, then add the Belimo PICCV (2-way Pressure Independent Characterized Control Valve). Think savings, and not necessarily first cost of equipment. Add a VFD (with its known and accepted benefits) and a Belimo PICCV as your flow control valve, and you have now optimized your system flow for very little additional cost. expansion device expansion device refrigerant-to-air heat exchanger refrigerant-to-air heat exchanger Heat Pump in Heating Mode refrigerant-to-water heat exchanger pump Heat Pump in Cooling Mode refrigerant-to-water heat exchanger compressor reversing valve pump compressor reversing valve water loop water loop 65

66 P2 Series PICCV for Water Source Heat Pumps for Fast Running Time with Switch Options and On/Off, Non-Spring Return Actuator Two-way Valve with Chrome Plated Brass Ball and Brass Stem Service: Flow Characteristic: Media Temp Range: Ambient Temp Range: Differential Pressure Across Valve Range (ΔP): chilled or hot water, 60% glycol equal percentage 0 F to 212 F [-18 C to 100 C] -22 F to 122 F [-30 C to 50 C] 5 to 50 psid Actuator: Running Time: Power Supply 40 sec 24 VAC/VDC LRCB P2 Pressure Independent Characterized Control Valve, Chrome Plated Brass Ball and Brass Stem Valve Non-Spring Return Actuator Model Valve On/Off # Flow Rate Nominal Size Close- PICCV Liter/ DN Off Valve GPM sec Inches mm psi LRCB24-3 PICCV * / Pg 66 PICCV * / Pg 66 PICCV * / Pg 66 PICCV * / Pg 66 PICCV * / Pg 66 PICCV * / Pg 66 PICCV * / Pg 66 PICCV / Pg 66 PICCV / Pg 66 PICCV / Pg 66 PICCV / Pg 66 PICCV / Pg 66 PICCV ** Pg 66** PICCV ** Pg 66 PICCV ** Pg 66 PICCV ** Pg 66 Electrical 3 ft cable Connection 1/2 conduit fitting LRCB24-3 Note: Other actuator options including switch options are available. Please contact your Belimo Account Manager or call for assistance. Options (add to list price) LRCB24-3-S Built-in aux. switch (-S) Pg 68 *1/2 body has two different disc sizes (.50 GPM to 1 GPM) (1.5 GPM to 5.5 GPM) **1 body has two different disc sizes (12 GPM to 16 GPM) (17 GPM to 19 GPM) 66

67 Service: Flow Characteristic: Media Temp Range: Ambient Temp Range: Differential Pressure Across Valve Range (ΔP): P2 Series PICCV for Water Source Heat Pumps for Fast Running Time with Switch Option and On/Off, Non-Spring Return Actuator Two-way Valve with Chrome Plated Brass Ball and Brass Stem with P/T Ports, NPT Female Ends chilled or hot water, 60% glycol equal percentage 0 F to 212 F [-18 C to 100 C] -22 F to 122 F [-30 C to 50 C] 5 to 50 psid Actuator: Running Time: Power Supply 40 sec 24 VAC/VDC LRCB P2 Pressure Independent Characterized Control Valve, Chrome Plated Brass Ball and Brass Stem, P/T Ports Valve Non-Spring Return Actuator Model Valve On/Off # Flow Rate Nominal Size Close- PICCV Liter/ DN Off Valve GPM sec Inches mm psi LRCB24-3 PICCV PT* / Pg 66 PICCV PT* / Pg 66 PICCV PT* / Pg 66 PICCV PT* / Pg 66 PICCV PT* / Pg 66 PICCV PT* / Pg 66 PICCV PT* / Pg 66 PICCV PT / Pg 66 PICCV PT / Pg 66 PICCV PT / Pg 66 PICCV PT / Pg 66 PICCV PT / Pg 66 PICCV PT** Pg 66 PICCV PT** Pg 66 PICCV PT** Pg 66 PICCV PT** Pg 66 Electrical 3 ft cable Connection 1/2 conduit fitting LRCB24-3 Options (add to list price) LRCB24-3-S Built-in aux. switch (-S) Pg 68 *1/2 body has two different disc sizes (.50 GPM to 1 GPM) (1.5 GPM to 5.5 GPM) **1 body has two different disc sizes (12 GPM to 16 GPM) (17 GPM to 19 GPM) 67

68 Pressure Independent Characterized Control Valve with On/Off, Non-Spring Return Actuator, P/T Ports (Optional) Application: The Pressure Independent Characterized Control Valve along with the LRCB24-3 is paired together specifically for use in Heat Pump applications to precisely control the flow of condenser water. This assembly is suitable for use in a hydronic system with constant or variable flow. Valve Specifications Service chilled or hot water, 60% glycol Flow characteristic equal percentage Size 1/2, 3/4, 1 Type of end fitting female, NPT Materials: Body forged brass, nickel plated Ball chrome plated brass Stem chrome plated brass Seat O-rings Viton Seat fiberglass reinforced teflon PTFE Characterizing disc TEFZEL Packing 2 EPDM O-rings, lubricated Diaphragm polyester reinforced silicone Regulator components stainless steel/brass/delrin 500 AF Spring stainless Steel Pete s Plug* (Qty 2) 1/4 brass/nortel (Optional P/T) Body pressure rating 600 PSI Media temp. range 0 F to 212 F [-18 C to 100 C] Close off pressure 200 PSI Leakage ANSI Class IV (0.01% of rated valve capacity at 50 psi differential) Flow rate 1/2 0.5 GPM [.03 l/s], 1 GPM [.06 l/s], 1.50 GPM [0.09 l/s], 2 GPM [.13 l/s], 3 GPM [.19 l/s], 4 GPM [.25 l/s], 5 GPM [.32 l/s] Flow rate 3/4 6 GPM [0.37 l/s], 7 GPM [0.44 l/s], 8 GPM [0.50 l/s], 9 GPM [0.57 l/s], 10 GPM [0.63 l/s] Flow rate 1 12 GPM [0.76 l/s], 14 GPM [0.88 l/s], 16 GPM [1.01 l/s], 18 GPM [1.14 l/s] Rangeability 100 : 1 Differential pressure 5 to 50 PSI operating range Flow accuracy (absolute) ± 5% (5 to 50 PSI) Variation due to ± 5% (5 to 50 PSI) manufacturing tolerances Hysteresis (absolute) 1% Weight of valve body 1/2 = 2.52 lbs, 3/4 = 3.05 lbs 1 = 4.98 lbs Tefzel and Teflon are registered trademarks of Dupont *Pete s Plugs offered as an option on 1/2, 3/4 and 1 valves. Actuator Specifications LRCB24-3 On/Off Power Supply 24 VAC ± 20% 50/60 Hz 24 VDC ± 10% Power Consumption 1.5 W (0.2 W) Transformer Sizing 3 VA (Class 2 power source) Electrical Connection 18 GA plenum rated cable 1/2 conduit connector 3 ft [1m] 10 ft [3m] 16 ft [5m] Overload Protection electronic throughout 0 to 95 rotation Control On/Off Input Impedance 600Ω Angle of Rotation 95 Direction of Rotation reversible with protected switch Position Indication handle Manual Override external push button and handle Running Time 40 second constant independent of load Humidity 5 to 95% RH non condensing (EN ) Ambient Temperature -22 F to +122 F [-30 C to +50 C] Storage Temperature -40 F to +176 F [-40 C to +80 C] Housing NEMA 2/IP54 Housing Material UL94-5VA Agency Listings culus acc. to UL A/-2-14, CAN/CSA E , CSA C22.2 No , CE acc. to 89/336/EEC and (-S Models) 2006/95/EC Noise Level <35dB(A) Quality Standard ISO 9001 LRCB24-3-S Auxiliary Switch 1 SPDT, 3A (0.5A 250 V Weight of Actuator 1.08 lbs [0.49 Kg] Rated Impulse Voltage 800V, Type of action 1 (1.B for -S version), Control Pollution Degree 3. 68

69 Pressure Independent Characterized Control Valve with On/Off, Non-Spring Return Actuator Dimensions LRCB24-3 LRCB24-3 with P/T Ports 2.6" [66] 6.5" [165] D " [66] 6.5" [165] D " [82] 1.69" [42] 2.34" [59.4] 3.22" [82] 1.69" [42] 2.34" [59.4] 0.78" [20] FlowSetR Dimensions 0.78" [20] FlowSetR Dimensions C C D D E F B A E F B A Dimensions (All ratings in brackets are in millimeters.) Valve A B C D E F 1/2" NPT 4.80 [122] 4.6 [117] 4.02 [102] 2.28 [58] 1.04 [24.4] 1.3 [33] 3/4" NPT 5.25 [133] 5.03 [128] 4.22[107] 2.38 [61] 1.04 [24.4] 1.3 [33] 1" NPT 7.05 [179] 6.85 [174] 4.80 [122] 3.23 [82] 1.60 [40.6] 1.60 [40.6] Dimensions (All ratings in brackets are in millimeters.) Valve A B C D E F 1/2" NPT 5.3 [135] 4.6 [117] 5.4 [137] 3.69 [94] 1.04 [24.4] 2.60 [66] 3/4" NPT 5.8 [147] 5.03 [128] 5.7 [145] 3.69 [94] 1.04 [24.4] 2.60 [66] 1" NPT 7.05 [179] 6.85 [174] 6.05 [154] 4.0 [102] 1.60 [40.6] 2.90 [73.65] Wiring Diagram Line Volts WARNING Live Electrical Components! During installation, testing, servicing and troubleshooting of this product, it maybe necessary to work with live electrical components. Have a qualified licensed electrician or other individual who has been properly trained in handling live electrical components perform these tasks. Failure to follow all electrical safety precautions when exposed to live electrical components could result in death or serious injury VAC Transformer a open a closed The indication of direction is valid for switch position 1. 3 a 3 Blk (1) Common Red (2) + Wht (3) LRCX24-3 Notes: 1 Provide overload protection and disconnect as required. Actuators may also be powered by 24 VDC. Meets culus requirements without the need of an electrical ground connection. W569 LRCB24-3 On/Off 69

70 ZS-CCV New Control Valve Weather Shield Installation Instructions APPLICATION The ZS-CCV weather shield provides moderate protection for valves which are mounted outdoors. This product is designed as a water tight enclosure. The housing allows easy mounting over the actuator, while allowing easy viewing of the actuator in operation. Weather shield for PICCV/CCV to provide protection for actuators in outdoor applications. Specifications Cover Perimeter Gasket Rubber Gasket Spring Clips Temperature limitations: Plate (ZS-CCV-100) Plate PARTS LIST PETG with UV resistant smoke tint Silicon Rubber Silicon Rubber Stainless Steel -22 F to 122 F (-30 C to 50 C) Aluminum Galvaneal w/black powder coat WEATHER SHIELDS* ZS-CCV-60 Pressure Independent Characterized Control Valves (PICCV) ZS-CCV-90 Pressure Independent Characterized Control Valves (PICCV) ZS-CCV-100 Pressure Independent Characterized Control Valves (PICCV) *Designed for NEMA 4 specifications Cover including Rubber Perimeter Gasket, Rubber Gasket Back Plate Anti-Rotation Post with screw and lock washer Valve Gasket Part Number L W H ZS - CCV [254] 7.75 [197] 4 [100] ZS - CCV [413] 8.75 [222] 4.5 [114] ZS - CCV [398] 7.61 [193] 4.0 [102] LR (B) (X) (CX) AR (X) (CX) LF AF List Price with CCV EXT-KIT Assorted Cap plugs for unused holes Screws: LF - 2 screws provided AF - 2 bolts with nylon insert locking nuts LR(B)(X)(CX), AR(X)(CX) - 1 screw, 1 washer 70

71 Flexible Products Introduction Table of Contents Flexible Section Introduction...73 Ordering...74 Non-Spring Return At A Glance...75 MFT Programming Codes...76 Non-Spring Return Base Actuator Table...76 Multi-Functional Technology Belimo damper actuators and control valves with Multi-Function Technology (MFT) include standard 2 to 10 VDC proportional control functions, plus they can be re-programmed. Parameters can be changed on-site to optimize/enable application. Parameters can be set for voltage control (VDC), time proportional control (PWM), floating point, on-off or feedback signal. You can also set, modify or read position, running time, mechanical working range, address, status, and diagnostics. MFT allows you to adapt the actuator to your system for service replacement and to improve system functionality. 71

72 Flexible Products Ordering Ordering example Non-Spring Return The ordering process for the new Flexible non-spring return actuators is very simple. First select a base actuator that meets the needs of the application and then simply add the desired options. 1. Valve Assembly PICCV PT+ARX24-MFT (AR100) OC1 A19 Flexible list add Select a valve assembly Torque or linear force, control input, position feedback, power supply 2. Clamp option Default valve linkage (O) 3. Electrical Connection option 16 ft. [5m] 18 GA, plenum rated cable (C5) Default connection is a 3 ft. [1m] long cable. 10 ft [3m] or 16ft [5m] cables are also available. 4. Programming P (A19) For MFT type actuators refer to page 79 for available configurations. 5. Total PICCV PT+ARX24-MFT (AR100 OC5 A19) Ordering example Spring Return 1. Valve Assembly PICCV PT+AF24-MFT-S US Select a base actuator 2. Programming P (A19) 2 10 VDC input / 2 10 VDC feedback Select pre-set programming code P-100xx (Axx) P-200xx (Wxx) P-300xx (Fxx) Control voltage applications Pulse width modulation applications Floating point applications Or create custom MFT configuration codes, see page 82 Or create custom MFT configurations in the field with MFT-Actuate PC software. 3. Total PICCV PT+AF24-MFT-S US+P10019 (A19) 72

73 Flexible Valve/Actuator Selection At A Glance Base product nomenclature PICCV + Non-Spring Return MFT, Multi-Functional Technology Model Description Reorder for actuator PICCV PT ARX 24 MFT AR 100 O C1 A19 VALVE SIZES Valve Designation Sizes PICCV Valve = 1/2 2 Power Supply VAC/DC Electrical Connection The reorder# is a complete description of the flexible actuator, including all custom options. blank 3 ft cable TYPE OF VALVE PRESSURE INDEPENDENT CHARACTERIZED CONTROL VALVE (CCV) P2 2-way Stainless Steel Ball & Stem Actuator family and torque/force output Actuator LR AR Torque 45 in-lb 180 in-lb Control Type MFT Multi-Function technology 3 On/Off-Floating Point Reorder number break-down Base Actuator Linkage Electrical connector options Programming codes AR 100 O C1 A19 See Base Actuators Page 74 Electrical connector options Code Description* C1 Default, 3 ft [1m] cable C3 10 ft [3m] cable C5 16 ft [5m] cable *24V actuators supplied with 18GA plenum rated cable. Options Codes Description (MFT Only) A19 P-10019* A28 P AAJ P AAK P AD5 P W31 P W32 P W34 P F03 P *For On/Off control input, please order P and wire as on/off. 73

74 Flexible Products MFT Programming Codes PRODUCTS Base Actuator Running Angle of Power VA Weight Built-in Model Codes Control Input Feedback Time Rotation/Stroke Supply Rating (lb) Aux. Switch 180 in-lb [20 Nm] LRX24-3 LR000 Floating Point 2-10 VDC 90 (Default) 95 deg 24 VAC/DC LRX24-3-S LR020 Floating Point 2-10 VDC 90 (Default) 95 deg 24 VAC/DC Yes LRX120-3 LR060 Floating Point 2-10 VDC 95 (Default) 95 deg 120 VAC LRX24-MFT LR VDC (Default) 2-10 VDC 100 (Default) 95 deg 24 VAC/DC LRCB24-3 LR000 on/off 2-10 VDC deg 24 VAC/DC LRCB24-3-S LR020 on/off 2-10 VDC deg 24 VAC/DC Yes ARX24-MFT AR VDC (Default) 2-10 VDC 100 (Default) 95 deg 24 VAC/DC For correct code please call Belimo Customer Service Multi-Function Technology Description Code Control Input Built-in Feedback Running Time DC Voltage P-10019* A VDC 2-10 VDC 100 P A VDC 0-10 VDC 100 P AAJ 2-6 VDC 2-10 VDC 100 P AAK 6-10 VDC 2-10 VDC 100 P AD5 2-5 VDC 2-10 VDC 100 Pulse Width Modulation P W sec. PWM 2-10 VDC 100 P W sec. PWM 2-10 VDC 100 P W sec. PWM 2-10 VDC 100 Floating Point P F03 Floating Point 2-10 VDC 100 On/Off P-10019* J13 On/Off 2-10 VDC 100 **Please Note: For On/Off control input, please order P and wire as on/off. 74

75 Specifying Pressure Independent Characterized Control Valves (1/2 2 ) Specifying Pressure Independent Characterized Control Valves Master Format To be inserted into Section HVAC Instrumentation and Controls 2.16 CONTROL VALVES A. Control Valves: Factory fabricated of type, body material, and pressure class based on maximum pressure and temperature rating of the piping system, unless otherwise indicated. B. Pressure Independent Control Valves a. Manufacturers: i. BELIMO AIRCONTROLS (USA), INC. b. The modulating control valves shall be pressure independent. c. The control valves shall accurately control the flow from 0 to 100% full rated flow with an equal percentage flow characteristic. The flow shall not vary more than +/- 5% due to system pressure fluctuations across the valve with a minimum of 5 PSID across the valve. d. Forged brass body rated at no less than 400 PSI, chrome plated brass ball and stem, female NPT union ends, dual EPDM lubricated O-rings and TEFZEL characterizing disc. e. Combination of actuator and valve shall provide a minimum close-off pressure rating of 200 PSID. f. The control valve shall require no maintenance and shall not include replaceable cartridges. g. All actuators shall be electronically programmed by use of a handheld programming device or external computer software. Programming using actuator mounted switches or multi-turn actuators are NOT acceptable. [Actuators for 3-wire floating (tri-state) on 1/2 1 pressure independent control valves shall fail in place and have a mechanical device inserted between the valve and the actuator for the adjustment of flow.] [Actuators for two-position 1/2 1 pressure independent control valves shall fail in place and have a mechanical device inserted between the valve and the actuator for the adjustment of flow.] [Actuators shall be provided with an auxiliary switch to prove valve position.] h. The actuator shall be of the same manufacturer as the valve, integrally mounted to the valve at the factory via a single screw on a four-way DIN mounting-base. i. The control valve shall require no maintenance and shall not include replaceable cartridges. j. The manufacturer shall warrant all components for a period 5 years from the date of production, with the first two years unconditional. k. The use of pressure independent valves piped in parallel to achieve the rated coil flow shall be permitted. Actuators shall be electronically programmed to permit sequencing the flow with a single control output point. The use of external devices to permit sequencing is NOT acceptable. To be inserted into Section HYDRONIC PIPING 2.6 CONTROL VALVES K. Calibrated Balancing Valves and Automatic Flow-Control Valves shall not be required on devices where pressure independent control valves are installed. NOTE TO BE ADDED TO THE PIPING DETAIL: Strainers shall not be required in front of each pressure independent control valve. A Type 20 strainer (or equivalent) should be installed in the system, in additional to other system strainers. To be inserted into Section TESTING, ADJUSTING, AND BALANCING 3.11 PROCEDURE FOR HYDRONIC SYSTEMS [CHOOSE ONE OF THE FOLLOWING TWO PARAGRAPHS] H. Systems installed with pressure independent control valves shall not require hydronic system balancing. H. Systems installed with pressure independent valves shall require verification of flow for [10%] [20%] [25%] <Insert Percentage> of the total installed product. Exact locations of tested product to be coordinated with the design engineer. 75

76 Specifying Pressure Independent Characterized Control Valves (1/2 2 ) Specifying Pressure Independent Characterized Control Valves - Master Format To be inserted into Section INSTRUMENTATION AND CONTROL FOR HVAC 2.16 CONTROL VALVES A. Control Valves: Factory fabricated of type, body material, and pressure class based on maximum pressure and temperature rating of the piping system, unless otherwise indicated. B. Pressure Independent Control Valves a. Manufacturers: i. BELIMO AIRCONTROLS (USA), INC. b. The modulating control valves shall be pressure independent. c. The control valves shall accurately control the flow from 0 to 100% full rated flow with an equal percentage flow characteristic. The flow shall not vary more than +/- 5% due to system pressure fluctuations across the valve with a minimum of 5 PSID across the valve. d. Forged brass body rated at no less than 400 PSI, chrome plated brass ball and stem, female NPT union ends, dual EPDM lubricated O-rings and TEFZEL characterizing disc. e. Combination of actuator and valve shall provide a minimum close-off pressure rating of 200 PSID. f. The control valve shall require no maintenance and shall not include replaceable cartridges. g. All actuators shall be electronically programmed by use of a handheld programming device or external computer software. Programming using actuator mounted switches or multi-turn actuators is NOT acceptable. [Actuators for 3-wire floating (tri-state) on 1/2 1 pressure independent control valves shall fail in place and have a mechanical device inserted between the valve and the actuator for the adjustment of flow.] [Actuators for two-position 1/2 1 pressure independent control valves shall fail in place and have a mechanical device inserted between the valve and the actuator for the adjustment of flow.] [Actuators shall be provided with an auxiliary switch to prove valve position.] h. The actuator shall be of the same manufacturer as the valve, integrally mounted to the valve at the factory via a single screw on a four-way DIN mounting-base. i. The control valve shall require no maintenance and shall not include replaceable cartridges. j. The manufacturer shall warrant all components for a period of 5 years from the date of production, with the first two years unconditional. k. The use of pressure independent valves piped in parallel to achieve the rated coil flow shall be permitted. Actuators shall be electronically programmed to permit sequencing the flow with a single control output point. The use of external devices to permit sequencing is NOT acceptable. To be inserted into Section HYDRONIC PIPING 2.6 CONTROL VALVES K. Calibrated Balancing Valves and Automatic Flow-Control Valves shall not be required on devices where pressure independent control valves are installed. NOTE TO BE ADDED TO THE PIPING DETAIL: Strainers shall not be required in front of each pressure independent control valve. A Type 20 strainer (or equivalent) should be installed in the system, in additional to other system strainers. To be inserted into Section TESTING, ADJUSTING, AND BALANCING FOR HVAC 3.11 PROCEDURE FOR HYDRONIC SYSTEMS [CHOOSE ONE OF THE FOLLOWING TWO PARAGRAPHS] H. Systems installed with pressure independent control valves shall not require hydronic system balancing. H. Systems installed with pressure independent valves shall require verification of flow for [10%] [20%] [25%] <Insert Percentage> of the total installed product. Exact locations of tested product to be coordinated with the design engineer. 76

77 Actuator/Valve Specification Download specifications at I. GENERAL A. Warranty all actuators for a period of two or five years from the production date as stated in the Terms and Conditions of Sale and Warranty. B. Electronic valve and damper actuators shall be as manufactured, brand labeled, or distributed by Belimo. C. Electronic control valves, as specified, shall be Belimo or other brands manufactured, brand labeled or distributed by Belimo. D. Other manufacturers must be approved, in writing, 10 days prior to the bid date. II. PRODUCTS A. Electronic Damper Actuators 1. Electronic actuators, less than 600 in-lb. of rated torque, shall have ISO 9001 quality certification and be culus listed under standard or UL listed under standard 873, CSA C22.2 No. 24 and have CE certification. 2. Electronic actuators used on dampers shall be designed to directly couple and mount to a stem, shaft or ISO style-mounting pad. Actuator mounting clamps shall be a V-bolt with a toothed V-clamp creating a cold weld, positive grip effect. Single point, bolt, or single screw actuator type fastening techniques or direct-coupled actuators requiring field assembly of the universal clamp is not acceptable. 3. Actuators shall be fully modulating/proportional, pulse width,floating/tristate, or two position as required and be factory or field selectable. Actuators shall have visual position indicators and shall operate in sequence with other devices if required. 4. Optional auxiliary switches shall be available. 5. Actuators shall have an operating range of 22 to 122 F. 6. Proportional actuators shall accept a 0-10 VDC or 0-20 ma input signal and provide a 2-10 VDC or 4-20 ma (with a 500 W load resistor) operating range. 7. Actuators shall be capable of operating on 24, 120 or 230VAC, or 24VDC and Class 2 wiring as dictated by the application. Power consumption shall not exceed 10 VA for AC, including 120VAC actuators, and 8 watts per actuator for DC applications. 8. NEMA 2 rated actuators shall be provided with a three foot (minimum), pre-wired, electrical cable. Actuators requiring removal of the actuator cover for access to wiring terminals, exposing electronic, printed circuit boards to damage, are unacceptable. 9. Actuators shall have electronic overload protection or digital rotation sensing circuitry to prevent actuator damage throughout the entire rotation. End switches to deactivate the actuator at the end rotation or magnetic clutches are not acceptable. 10. For power-failure/safety applications, an internal mechanical spring return mechanism shall be built into the actuator housing. Spring return actuators shall be capable of CW or CCW mounting orientation. Spring return models > 60 in-lbs. and non-spring return models > 90 in-lbs. will be capable of mounting on shafts up to 1.05"in diameter. Spring return actuators with more than 60 in-lb. of torque shall have a metal, manual override crank. 11. Actuators using "on-board" chemical storage systems, capacitors, or other "on-board" non-mechanical forms of fail-safe operation are unacceptable. 12. Upon loss of control signal, a proportional actuator shall fail open or closed based on the minimum control signal. Upon loss of power, a nonspring return actuator shall maintain the last position. 13. Actuators shall be capable of being mechanically and electrically paralleled to increase torque if required. Valves and dampers requiring greater torque or higher close off may be assembled with multiple low torque actuators. 14. Dual mounted actuators using additional anti-rotation strap mechanical linkages, or special factory wiring to function are not acceptable. Actuators in a tandem pair must be "off the shelf," standard actuators ready for field wiring. 15. Damper and valve actuators will not produce more than 62 db (A) when furnished with a mechanical fail-safe spring. Non-spring return actuators shall conform to a maximum noise rating of 45 db(a) with power on or in the running or driving mode. 16. Proportional actuators shall be fully programmable. Control input, position feedback and running time shall be factory or field programmable. Diagnostic feedback shall provide indications of hunting or oscillation, mechanical overload, mechanical travel and mechanical load limit. The actuators shall also provide actuator service data, at minimum, number of hours powered and number of hours in motion. 17. Proportional actuators shall be capable of digital communication, as built. B. Smoke and Combination Fire and Smoke Actuators In Section or equivalent 1. All smoke and combination fire and smoke dampers shall be provided with Belimo Aircontrols FSLF (30 in-#), FSNF (70 in-#), or FSAF (133 in-#) actuators. 2. Equals shall be approved 10 days prior to submission of bid. 3. Actuator shall carry a manufacturer s 5-year warranty and be manufactured under ISO 9001 quality control. 4. Actuator shall have microprocessor or electronic based motor controller providing: a. Electronic cut off at full open so that no noise can be generated while holding open. Holding noise level shall be inaudible. b. Protection so that actuator shall be incapable of burning out if stalled before full rotation is reached. 5. Housing shall be steel and gears shall be permanently lubricated. 6. The actuators shall be direct coupled and employ a steel toothed coldweld clamp for connecting to damper or jack shafts. Aluminum clamps or set-screw attachment are not acceptable. 7. Actuator shall have UL555S Listing by the damper manufacturer for 250 F. 8. FSLF shall be applied on dampers up to 6 sq. ft. Current draw shall be no more than.15a at 120V running, or.06a holding at 120V (5 VA and 3.5 VA respectively for 24V power).fsnf shall be applied on dampers up to 16 sq.ft. Current draw shall be no more than.23a at 120V running, or.1a holding at 120V (27 VA and 10 VA respectively for 24V power). 9. FSAF shall be applied on dampers up to 20 sq.ft. Current draw shall be no more than.1a at 120V running, or.05a holding at 120V (10 VA and 3 VA respectively for 24V power). 10. Dampers shall be installed straight and true, level in all planes, and square in all dimensions. Dampers shall move freely without undue stress due to twisting, racking, bowing, or other installation error. 11. Do not install in area where moisture can penetrate damper or actuator nor where actuator temperature exceeds 120 F. Note: FSLF and FSNF are 350 F actuators, 15 seconds open and close. UBC and UL555S FSAF is a 250F actuator, 75 seconds open, 20 seconds close. UL555S. C. Electronic Valve Actuators 1. Electronic actuators, less than 600 in-lb. of rated torque, shall have ISO 9001 quality certification and be culus listed under standard or UL listed under standard 873, CSA C22.2 No. 24 and have CE certification. 2. Electronic actuators used on valves shall be designed to directly couple and mount to a stem, shaft or ISO style-mounting pad. 3. Actuators shall be fully modulating/proportional, floating/tri-state, or two position as required and be factory or field selectable. 4. Optional auxiliary switches shall be available. 5. Actuators shall have an operating range of 22 to 122 F. 6. Proportional actuators shall accept a 0-10 VDC or 0-20 ma input signal and provide a 2-10 VDC or 4-20 ma (with a load resistor) operating range. 7. Actuators shall be capable of operating on 24VAC, 120VAC or 230VAC, or 24VDC and Class 2 wiring as dictated by the application. Power consumption shall not exceed 10 VA for AC, including 120VAC actuators, and 8 watts per actuator for DC applications. 8. NEMA 2 rated actuators shall be provided with either a covered terminal strip, or a three, six, or ten foot pre-wired, electrical cable. 9. For power-failure/safety applications, an internal mechanical spring return mechanism shall be built into the actuator housing. Spring return actuators shall be capable of CW or CCW mounting orientation. Spring return actuators with more than 60 in-lb. of torque shall have a metal, manual override crank. 10. Actuators using "on-board" chemical storage systems, capacitors, or other "on-board" non-mechanical forms of fail-safe operation are unacceptable. 11. Upon loss of control signal, a proportional actuator shall fail open or closed based on the minimum control signal. Upon loss of power, a nonspring return actuator shall maintain the last position. 12. Actuators utilizing brushless DC technology shall be capable of being mechanically and electrically paralleled to increase torque if required. Valves requiring greater torque or higher close off may be assembled with two low torque actuators. 77

78 Actuator/Valve Specification 13. Dual mounted actuators using additional anti-rotation strap mechanical linkages, or special factory wiring to function are not acceptable. Actuators in a tandem pair must be "off the shelf," standard actuators ready for field wiring. 14. Valve actuators will not produce more than 62 db (A) when furnished with a mechanical fail-safe spring. Non-spring return actuators shall conform to a maximum noise rating of 45 db(a) with power on or in the running or driving mode. 15. Proportional actuators shall be fully programmable. Control input, position feedback and running time shall be factory or field programmable. Diagnostic feedback shall provide indications of hunting or oscillation, mechanical overload, mechanical travel and mechanical load limit. The actuators shall also provide actuator service data, at minimum, number of hours powered and number of hours in motion. 16. Proportional actuators shall be capable of digital communication, as built. D. Industrial Actuators 1. Belimo SY Series Industrial Electric Actuators a. The valve actuator shall consist of a thermally protected capacitor-type reversible electric motor, a patented planetary worm combination drive, heater, limit switches and wiring termination blocks, all contained in a die cast aluminum enclosure. The drive system will provide continuous, smooth torque transmission throughout a 90 degree travel. Adjustable stops provide mechanical adjustment of end-of-travel. The transmission shall allow continuous duty operation of a manual override handwheel without the need to remove power, or de-clutch the manual system. b. Enclosure shall be designed to meet NEMA 4, 4X (weatherproof) requirements, or CSA approved for non-hazardous locations. c. The actuator shall employ ISO5211 mounting standards to provide for a wide range of international applications. d. The enclosure will have an industrial quality coating. e. Actuator shall have a motor rated for a minimum of 25% duty cycle in modulating applications. f. Actuator shall be suitable for operation in ambient temperature ranging from -4 F to +150 F [-20 C to +65 C]. g. The motor shall be fractional horsepower; permanent split capacitor type designed to operate on 24 VAC, 110 VAC or 220 VAC, 1 ph, 50/60 Hz supply. A self resetting thermal switch shall be imbedded in the motor for overload protection. h. Internal terminal blocks shall be clearly marked for field wiring. A wiring diagram shall be permanently attached to the OUTSIDE of the actuator housing. i. Actuator will have a suitable sized NPT entry for external connections. j. Gears shall be hardened alloy steel, permanently lubricated. The worm drive system negates the need for a brake. k. Two adjustable cam actuated end travel limit switches shall be provided to control electrical movement of the actuator. l. 2 SPDT auxiliary switches, rated 10A at 250 VAC shall be included. The switches are factory pre-set at 3 degrees and 87 degrees rotation, and may be field adjusted. m. Actuator shall be equipped with a hand wheel or shaft for manual override to permit operation of the actuator in the event of electrical power failure or system malfunction. Hand wheel, where applicable, must be permanently attached to the actuator. (SY2 and larger) n. The handwheel override shall be continuously operational regardless of the powered state of the actuator, without the need to remove electrical power if present during the override phase. (SY2 and larger) o. The hand wheel will not rotate while the actuator is electrically driven. p. The actuator shall provide a visual indicator beacon on the top of the housing for position status of the actuator and attached devices. q. Actuator shall have an internal heater and thermostat to minimize the build-up of moisture inside the sealed enclosure. r. Modulating units shall operate under 2-10 VDC, 4-20mA, and 1-5 VDC control modes. The default shall be 2-10 VDC control. E. Electronic Control Valves 1. General a. The manufacturer shall be capable of providing individual valve identification tagging on each printed valve label. Valve tag identification shall be documented on the approved, submitted valve schedule. b. Valves shall be designed and provided with the proper actuators to provide the rated valve close-off. 2. Pressure Independent Characterized Control Valves a. Control valves shall be pressure independent. Balancing valves and associated balancing shall not be required on devices where pressure independent control valves are installed. Balancing valves and balancing are required if self-contained pressure independent control valves are not installed. b. The absolute flow accuracy through the valve shall be +/- 5 % due to system pressure fluctuations across the valve in the selected operating range, and +/- 5% variation due to manufacturing tolerances. c. The control valves shall be available with floating or proportional actuators. The actuator shall be directly coupled to the valve at the factory. Proportional actuators shall be Multi Function Technology as manufactured by Belimo. Multi-turn actuators are not acceptable. d. The valve shall have an equal percentage characteristic and shall accurately control the flow from 0 to 100% full rated flow. e. A minimum of 5 PSI shall be required to operate the valve pressure independently. f. Valves shall require no maintenance and shall not include replaceable cartridges. g. Valves shall be available with optional pressure/temperature ports to allow flow verification. h. Control valves shall be by Belimo. 3. Characterized Control Valves a. Control valves shall be of the Characterized Control Valve type provided by Belimo. b. Characterized Control Valves shall be used for all water applications requiring equal percentage characteristics. c. A TEFZEL flow-characterizing disc shall be installed in the inlet of Twoway characterized control valves and in the control port of Three-way valves. The valve trim shall utilize a stainless steel ball and stem for all water or glycol solutions up to 60%. For water applications, an optional chrome plated brass ball and brass stem may be used for sizes 3/4 and smaller. d. Valve bodies shall be nickel-plated, forged brass with female NPT threads. Bodies to 1-1/4" shall be rated at 600 psi and sizes 1-1/2" to 3" at 400 psi. e. Characterized Control Valves shall have a self-aligning, blowout proof, brass stem with a dual EPDM O-ring packing design. Fiberglass reinforced Teflon seats shall be used. f. The valves shall have a four bolt mounting flange to provide a 4 position, field changeable, electronic actuator mounting arrangement. g. A non-metallic coupling, constructed of high temperature, continual use material shall provide a direct, mechanical connection between the valve body and actuator. The coupling shall be designed to provide thermal isolation and eliminate lateral and rotational stem forces. Vent hole shall be provided to reduce condensation build-up. 4. Globe Valves a. Globe valves, as specified, shall be by Belimo. b. Two-way and Three-way globe valves may be used only if characterized control valves do not fit the sizing criteria or application. c. Globe valves may be used for chilled or hot water, steam, or glycol solutions to 60%. Screwed and flanged water valves shall have equal percentage or linear flow characteristics for Two-way or Three-way valves, respectively. All stems shall be stainless steel. d. Screwed globe valves 1/2" through 2" shall have bronze bodies rated at ANSI Class 250. For water up to 35 psi or steam up to 15 psi, trim shall include a brass plug, a spring-loaded TFE packing, and a bronze seat. The maximum differential shall be 35 psi for water and 15 psi for steam. e. Two-way and Three-way flanged globe valves 2-1/2" to 6" shall have cast iron bodies rated for ANSI Class 125 or ANSI 250. The maximum differential shall be 25 psi for water and 10 psi for steam. Trim shall include stainless steel stems, bronze plugs, bronze seats, and a NLP packaging or a complete stainless steel trim and a TFE V-ring packaging. f. For steam inlet pressures higher than those stated above, furnish globe valves with stainless steel trim specifically rated for the application. 78

79 Actuator/Valve Specification 5. Direct Coupled Globe Valve Actuator and Adaptor Bracket a. Actuator shall be designed with an integrated adaptor bracket that will direct mount to the valve. b. Actuator shall provide a linear force capable of fulfilling the required close-off of the valve. c. Actuator shall include an automatic valve coupling device that shall lock securely to the valve stem. d. Proportional and spring return actuators shall adapt upon powering the actuator. This adaptation will determine stroke length and enable the actuator to set the minimum and maximum limits of the supplied control signal, thereby utilizing the entire control signal range. Feedback, running time and other parameters are automatically adjusted to the effective stroke. e. Actuator shall have a manual override equipped with an interlocking device to protect the actuator from over-torque of the manual override. 6. Butterfly Valves Resilient Seat a. Butterfly valves, as specified, shall be by Belimo. b. Butterfly valves 2" to 12" shall have a fully lugged, drilled and tapped, cast iron body, rated to 200 psi body pressure, with 14" and larger valves having a body pressure rating of 150 psi. Flanges shall meet ANSI 125/150 standards. The one-piece body shall feature an extended neck allowing sufficient clearance for flanges and 2" of piping insulation. The disc shall be 304 stainless steel and provide bi-directional bubble-tight close off in either direction for chilled or hot water or 50% glycol applications. The disc shall be polished and contoured to minimize torque and wear. Shaft shall be mechanically retained in valve body using split-thrust washer and internal retaining-ring design for ease of service. The valve body shall employ ISO5211 actuator mounting and shaft connection standards. c. The disc shall have full 360-degree concentric seating. Valves up through 12" shall utilize an internal spline for the disc-to-stem connection. External mechanical methods to achieve this mechanical connection, such as pins or screws, shall not be employed. Valves 14" and larger will utilize a dualpin method to prevent the heavy disc from settling onto the liner, causing distortion. A phenolic backed, non-collapsing, EPDM seat shall be field replaceable and shall create a positive seal between flange face and valve body. No gaskets shall be required between the valve and flange faces. The shaft shall be supported at four locations by RPTFE bushings. d. The flow characteristic shall be modified equal percentage for Two-way valves and linear for Three-way valves. Valves 2" through 12" shall be rated for standard HVAC service of up to 50 psi close-off, or for heavy commercial service of up to 200 psi close-off. Valves 14" and larger shall be rated for up to 150 psi close-off. e. A permanent metal tag shall designate manufacturer, series number and materials of construction. f. Butterfly valves may be used in all two-position applications and modulating applications larger than 2", or where the close off rating of other valve styles does not meet the design requirements. g. Butterfly valves shall be sized primarily by using velocity calculations to prevent fluid velocities from exceeding 12 feet per second. For modulating applications, CV factors at sixty (60) degrees shall be used for determining delta P once size has been determined by the velocity calculations. h. High torque industrial valve actuators, >300 in-lb. of rated torque, may be used where low torque actuators are not suitable. High torque actuators shall be as manufactured or provided by Belimo. 7. Butterfly Valves High Performance a. Butterfly valves, as specified, shall be by Belimo. b. Butterfly valves 2" to 30" shall have a fully lugged, drilled and tapped, carbon steel body conforming to ANSI class 150 or class 300 standards. Flanges shall meet ANSI 150 or ANSI 300 standards. The one-piece body shall feature an extended neck allowing sufficient clearance for flanges and 2" of piping insulation. c. The disc shall be 316 stainless steel and provide bi-directional bubbletight close off in either direction for chilled or hot water, 50% glycol applications or steam applications up to the ANSI class limits. The disc shall employ a 360 degree uninterrupted spherical edge for sealing. The disc profile shall be designed for maximum flow and equal percentage control. d. Shaft shall be mechanically retained in the valve body using an adjustable gland flange. This flange also serves to prevent leakage out the valve neck by applying a load against TFE Chevron design washers. These washers provide full ANSI hydrostatic seal to 150% of CWP rating. e. The RTFE bi-directional seat shall employ an encapsulated elastomeric o-ring core for resiliency. The seat is retained in the valve body by use of a retaining ring. The outside diameter of the retaining ring is recessed within the gasket sealing surface to prevent external leakage. The retaining ring is held in place by means of a stainless wedge ring. f. A permanent metal tag shall designate manufacturer, recommended flow direction, series number and materials of construction. g. Butterfly valves may be used in all two-position applications and modulating applications larger than 2", or where the close off rating of other valve styles does not meet the design requirements. h. Butterfly valves shall be sized primarily by using velocity calculations to prevent fluid velocities from exceeding 32 feet per second. For modulating applications, CV factors at sixty (60) degrees shall be used for determining delta P once size has been determined by the velocity calculations. i. High torque industrial valve actuators, >300 in-lb. of rated torque, may be used where low torque actuators are not suitable. High torque actuators shall be as manufactured or provided by Belimo. 8. Zone Valves a. Zone valves, as specified, shall be by Belimo. b. Zone valves shall be used in terminal unit water applications requiring a Two-way or Three-way diverting valve in sizes 1 and smaller. c. Zone valves shall have brass bodies with female NPT or sweat ends and a stainless steel stem. d. Zone valve actuators shall on/off and shall be available in 24VAC or 120VAC. e. Zone valve actuators shall have a minimum of 20 psi close-off rating. f. Zone valves shall have push button for quick removal of actuator. g. Zone valves shall have a leakage rate of 0.1% or lower 9. Industrial Ball Valves a. Ball valves, as specified, shall be by Belimo. b. Two-way and three-way ball valves may be used only if characterized control valves do not fit the sizing criteria or application. c. Ball valves may be used for chilled or hot water, steam, or glycol solutions to 50%. Screwed or flanged water valves shall have modified equal percentage or modified linear flow characteristics for two-way and threeway valves, respectively. The ball and stem shall be stainless steel, and seats will be RPTFE. d. VS Series screwed ball valves 1/2" through 3" shall have bronze bodies rated to at least 400 WOG. Flanged ball valves 2" through 10" shall have cast iron bodies rated to at least 200 WOG. The maximum differential rating will match the respective valve close-off rating. e. VSS Series screwed ball valves 1/2" through 3" shall have stainless steel bodies rated to at least 600 WOG. The maximum differential rating will match the respective valve close-off rating. f. VS and VSS series ball valves shall provide bubble-tight close-off capabilities on all ports up to the specified close-off rating. 79

80 Terms and Conditions of Sale and Warranty I. General 1.1. The following Terms and Conditions of Sale ( Terms ) apply to the sale of products described in this Product Guide ( Products ). As used herein, Seller or Belimo refers to Belimo Aircontrols (USA) Inc. or Belimo Aircontrols (CAN) Inc., as applicable, and Client refers to the individual or business entity that purchases the Products from Seller. These Terms shall apply unless the parties mutually agree to different terms and memorialize such agreement in a writing signed by both Client and Seller. II. III. IV. Price 2.1. The Seller s price for Products (the Price ) is net, F.O.B. Point of Origin, and is calculated in US currency for sales made by Belimo Aircontrols (USA), Inc. and calculated in Canadian currency for sales made by Belimo Aircontrols (CAN) Inc. 2.1.The Price, unless otherwise agreed upon, does not include freight and packaging (wooden crates, pallets, etc), the costs of which will be charged to Client at cost for each shipment and shall be payable with payment of the Price Orders for Products with a net value of less than US$300 (CAN$450) will be subject to a US$20 (CAN$35) handling fee (the Handling Fee ). The Handling Fee will not be charged for orders of Products with a net value equal to or greater than US$300 (CAN$450) or for Products ordered through Seller s internet ordering system at: Seller reserves the right to make partial deliveries of orders of Products, each of which deliveries may be invoiced separately by Seller The Price does include charges for wiring diagrams, installation, and commissioning, which will be charged to Client separately and will be payable on demand. Payment 3.1. Invoices are payable in US currency for sales made by Belimo Aircontrols (USA), Inc. and in Canadian currency for sales made by Belimo Aircontrols (CAN) Inc. and are due no later than 30 days from the date of invoice, without any deductions If Client fails to pay the entire invoice balance within 60 days from the date of the invoice, Client will be subject to an interest charge of 2% per month (or the maximum rate permitted by law, whichever is less) on the outstanding unpaid balance due to Seller Clients who maintain outstanding balances for 45 days or more after the date of invoice may be subject to restricted shipments of Products or may be required to pay for all future deliveries of Products on a cash-on-delivery basis. Title and Risk 4.1. Title to all Products shall remain with Seller and shall not pass to Client until Seller has received full payment for the Products. V. Damage or Loss in Transit 5.1. Seller assumes no liability for damage or loss of shipment of Products, which risk shall at all times remain with the carrier. All shipments must be unpacked and examined by Client immediately upon receipt. Any external evidence of loss or damage must be noted on the freight bill accompanying the shipment of Products or carrier s receipt and signed by the carrier s agent at the time of delivery. Failure to do so will result in the carrier s refusal to honor any claim relating to damage of Products. Client must also notify Seller of such damage by providing Seller with a copy of the freight bill or damage report so that VI. VII. Seller can file a claim for loss or damage in transit with the carrier. If the damage does not become apparent until the shipment is unpacked, customer must make a request for inspection by the carrier s agent and file with the carrier within 15 days after receipt of product and notify Seller of the same. Seller is not liable for consequential damage to Client s property or a third-party s property resulting from the installation of damaged Products. Delivery 6.1. Seller undertakes to make every attempt to adhere to its stated delivery parameters and to make a timely delivery of the Products but does not guarantee any delivery specifications. Each contract entered into for the purchase of Products is not cancelable nor is Seller liable for any direct or indirect losses that may arise, for any reason whatsoever, due to Seller s failure to meet any stated or assumed delivery schedules. Return of Goods 7.1. Products received by Client cannot be returned unless: (i) Client alerts Seller that it intends to return such Products, (ii) Seller agrees to accept the return of such Products, (iii) Client obtains a Return Material Authorization ( RMA ) number from Seller for the return of such Products, and (iv) Client follows all return instructions provided by the Seller. The RMA number must be clearly written on the outside of all packaging for any returned Products. Only Products returned to proper the location as instructed by Seller and identified with an RMA number will be considered for credit Only Products that are returned in original packaging may be accepted for return. Such returned Products must be received in good condition, adequate for resale as new Products to qualify for credit. Client will be responsible for payment of a restocking charge for all returned Products in an amount no less than 20% of the invoice value of the Products ( Restocking Charges ). All return Products must be shipped to Seller at Client s cost Returns that result from Seller errors will be credited in full and will not be subject to Restocking Charges. VIII. Warranty VIII.A 5-year Warranty 8.1. Products that are listed in this Product Guide as carrying a 5-year warranty and shipped after May 1, 2000 to a location in the United States or Canada shall carry a 5-year warranty. The 5-year warranty is unconditional for the first two years from the date of production of the Products. After the first two years from the date of Production, the warranty shall be conditional and the warranty coverage shall not apply to damage to Products caused by ordinary wear and tear, negligence or improper use by Client, or other causes beyond the control of the Seller. Product -specific terms of warranty with regard to warranty period or conditions of warranty may apply to certain specified Products as stated in the documentation for those Products. VIII.B 2-year Conditional Warranty 8.2. Products that are listed in this Product Guide as carrying a 2-year warranty and shipped after May 1, 2005 to a location in the United States or Canada shall carry a 2-year warranty. The 2-year warranty is conditional and the warranty coverage shall not apply to damage to Products caused by ordinary wear and tear, negligence or improper use by Client, or other causes beyond the control of the Seller. Product -specific terms of warranty with regard to warranty period or conditions of warranty 80

81 Terms and Conditions of Sale and Warranty may apply to certain specified Products as stated in the documentation for those Products. VIII.C General Warranty Terms 8.3. Seller s warranty may be null and void in the event of any: (a) modification or unauthorized repairs of Products by Client, (b) unauthorized incorporation or integration of Products into or with Client s equipment, (c) use of Products in an unauthorized manner, or (d) damage to Products not caused by Seller Client must promptly notify Seller of Products alleged defect and provide Seller with other evidence and documentation reasonably requested by Seller. Before removing Products from service, Client should contact a Seller-authorized support technician by calling Belimo customer service. The contact information for Belimo customer service is listed on the back page of Belimo s Product Guide and Price List ( PGPL ) or may be found at Belimo customer service will work with field technicians to troubleshoot problems. Many problems can be resolved over the phone If a problem cannot be resolved over the phone, an RMA number will be issued by Seller for return of the Products. Prior to returning any Products under a warranty, Client must obtain an RMA number from Seller, along with shipping instructions for the return. The RMA number must be clearly written on the outside of the box containing the returned Products. Only Products returned to the proper location and identified with an RMA number will be accepted by the Seller All returned Products should be packaged appropriately to prevent further damage. Seller reserves the right to refuse any returned material if improperly packaged or labeled (without an RMA number). Products returned without proper RMA documentation will void Seller s warranty Products found to be defective for which a warranty is applicable will either be replaced or repaired at the Seller s discretion. Seller is not responsible for charges that Client may incur as a result of the removal or replacement of Products Repaired or replacement Products are shipped from Seller via ground shipment. Other shipping methods are available at the sole expense of the Client Repaired, replaced or exchanged Products will carry a warranty for a period of time equal to the greater of: (i) the remainder of the original 5-year warranty or 2-year warranty that was applicable to the repaired, replaced or exchanged Products, or (ii) six months, effective from the date the repaired, exchanged or replaced Products are shipped by Seller (the Replacement Warranty Period ) Advanced replacement Products for Products covered under warranty may be obtained from Seller after the Belimo customer service troubleshooting process has been completed. For industrial products (such as butterfly valves), a purchase order is required. The purchase order will be credited upon the receipt and verification by Seller of the returned defective Products. For non-industrial products, an invoice will be issued and shall be due and payable is the returned Products are not received by Seller within 60 days from the date of that the replacement Products are shipped. Additional charges may apply if the nature of the problem has been misrepresented by Client Both the conditional and unconditional warranties cover the Products only, and do NOT cover labor associated with the troubleshooting, removal or replacement of such Products New Products ordered in an attempt to circumvent the warranty process may NOT be reimbursed if, upon receipt of returned Products, it is determined that the defect in the returned Products is actually field related, or the Products IX. have been returned for cosmetic reasons only Advanced replacement Products for butterfly valve actuators may not be new, but have been verified by the Seller for electrical and mechanical operation. Such Products carry the full warranty for the entire Replacement Warranty Period. No Warranty for Non-HVAC Application 9.1. All Seller warranties shall extend only to HVAC use of the Products. If Products are used in non-hvac application (e.g., aircraft, industrial processes, etc.), Seller s warranties shall not cover such Products. Client will be solely responsible for any damage to or malfunction of Products or for any damage resulting from such use of Products. X. Liability Disclaimer These Terms constitute the entire understanding and agreement between Seller and Client regarding the warranties that cover Products and supersedes all previous understandings, agreements, communications and representations. Seller shall not be responsible for and Client does not have any right to make any claim for, damage that occurs to any property other than Products. Seller shall in no way be responsible for any costs incurred by Client in the determination of the causes of damage to any of Client s property, for expert opinions, or for any punitive or special, incidental or consequential damages of any kind whatsoever. XI Seller shall not be liable for any damage resulting from or contributed by Client or third parties acting within the scope of responsibility of Client or such third party when: 1. Products are used for non-hvac applications, such as in aircrafts, industrial processes, etc.; 2. Client uses the Products without complying with applicable law or institutional regulations or Belimo data and installation sheets or Client uses the Products without following good industry practice; 3. Products are used by personnel who have not received suitable instruction; or 4. Products are modified or repaired without the written approval of Seller. When requested to do so, Client shall immediately release Seller in full from any possible third party claims resulting in connection with the circumstances listed above. This also applies to claims in connection with product liability If Client becomes aware that any third party has made or appears likely to make any claim regarding Products (including, without limitation, regarding Product defects or rights infringed by Products), then Client shall immediately inform Seller and afford to Seller all assistance that Seller may require to enforce its rights and defend such claim. Proper Law and Jurisdiction All sales of Products under these Terms and the warranties described herein shall be governed by the laws of the State of Connecticut, and the parties agree to submit to the exclusive jurisdiction of the Federal and state courts located in the State of Connecticut with respect to any dispute arising from the subject matter hereof. The parties hereby waive all rights to a jury trial in connection with any claims relating to the subject matter hereof. 81

82 Custom MFT Configuration Order Form FAX: USA Toll Free #1 Select an Actuator (use one sheet for each unique actuator/configuration) AF24-MFT US AF24-MFT-S US NF24-MFT US LF24-MFT US LF24-MFT-S US AF24-MFT95 US NV24-MFT US NVF24-MFT US NVF24-MFT-E US NVFD24-MFT US NVFD24-MFT-E US Quantity GMX24-MFT AMX24-MFT NMX24-MFT LMX24-MFT LRX24-MFT GMX24-MFT95 AMX24-MFT95 NMX24-MFT95 LMX24-MFT95 (-S=Auxiliary Switch) Quantity Name Company Address City State Zip Phone Fax Field Labeling: LBL-MFT Custom configuration labels required 1-3/8 X 1-1/4 orange labels preprinted to your specifications 12 label sets per sheet. Includes configuration code and wiring labels. #2 Create a Custom Configuration Angle of rotation setting ➀ Deactivated (Default) Activated ➁ ➄ The following settings - refer to the full angle of rotation of 95º. The following settings ➁ - ➄ are automatically adapted to the effective mechanical angle of rotation. Manual triggering by pressing the pushbutton twice Automatic triggering each time the unit is powered up or by pressing the pushbutton twice. Control Types ➁ Feedback signals U 5 ➂ Running time ➃ VDC PWM Floating On/Off to 5.0 sec to 25.5 sec. Variable Start. Running time 0.59 to 2.93 sec. Variable Stop. Start. Position Feedback U Position Feedback U Position Feedback U 150 s (Default) Stop. DC V (Default) DC V Note: The sound power level [db(a)] increases when the running time is below 150 s. Start DC. V (0...8 V) Finish DC. V ( V) s ( s) (in 5 sec. increments) LM s NM s AM s GM s Others s The finish must be at least 2 V above the start! Override control and electronic angle of rotation limiting ➄ Min. (min. position) = % ( %) (beginning of working range) default 0 ZS (intermediate position) = % ( %) (0% = Min.; 100% = Max.) default 50 Max.(max. position) = % ( %) (end of working range) default

83 Belimo Platinum Distributors USA ACR Supply Company Inc Hillsborough Road Durham, NC Phone: With branches in NC Aireco Supply 9120 Washington Boulevard Savage, MD Phone: With branches in MD, VA Amcon Controls, Inc Warfield Street San Antonio,TX Phone: With branch in Houston, TX Applied Automation A Wilson Mohr Company 3186 South Washington Street, #230 Salt Lake City, UT Phone: Boston Aircontrols, Inc. 8 Blanchard Road Burlington, MA Phone: Charles D. Jones Co. 445 Bryant Street, Unit #1 Denver, CO Phone: With branches in CO, MO, KS Climatic Control Co., Inc W. State Street Milwaukee, WI Phone: With branches in WI, IL Cochrane Supply and Engineering, Inc Stephenson Highway Madison Heights, MI Phone: With branches in MI Columbus Temperature Control 1053 E. 5th Avenue Columbus, OH Phone: Controlco 5600 Imhoff Drive, Suite G Concord, CA Phone: With branches in CA Edward C. Smyers & Co. 223 Fort Pitt Boulevard Pittsburgh, PA Phone: First Source Distributors, LLC 710 Peninsula Lane, Suite E Charlotte, NC Phone: G & O Thermal Supply 5435 N. Northwest Highway Chicago, IL Phone: With branches in IL Industrial Controls Distributors LLC 1776 Bloomsbury Avenue Wanamassa, NJ Phone: With branches in KY, ME, NC, NY, OH, PA, TN, MA, GA, WI, IL Interstate HVAC Controls 30 Vineland Street Brighton, MA Phone: Jackson Controls 1708 E. 10th Street Indianapolis, IN Phone: M & M Controls 9E West Aylesbury Road Timonium, MD Phone: Meier Supply 123 Brown Street Johnson City, NY Phone: With branches in NY, PA MICONTROLS, Inc th Place South Seattle, WA Phone: With branches in WA, OR Minvalco, Inc Gorham Avenue Minneapolis, MN Phone: With branches in MN RSD/Total Control Atlantic Ocean Drive Lake Forest, CA Phone: With branches in CA, NV, OR, AK, AZ, ID, UT, WA Saint Louis Boiler Supply, Co. 617 Hanley Industrial Court St. Louis, MO Phone: South Side Control Supply, Co. 488 N. Milwaukee Avenue Chicago, IL Phone: With branches in IL, IN Stromquist and Company 4620 Atlanta Road Smyrna, GA Phone: With branch in FL Temperature Control Systems Brockwood Road Dallas, TX Phone: With branches in OK, TX Tower Equipment Co., Inc West Broad Street Stratford, CT Phone: Twinco Supply Corporation 55 Craven Street Huntington Station, NY Phone: With branches in NY CANADA Airex C - 5 Sandhill Court Brampton, ON, L6T 5J5 Phone: Baymar Supply Co Jefferson Boulevard Windsor, ON, N8T 2W8 Phone: With branch in London, ON Le Groupe Master 1675 de Montarville Boucherville, QC, J4B 7W4 Phone: With branches across Eastern Canada O Dell Associates Inc. # Cooke Boulevard Burlington, ON, L7T 4A8 Phone: Prokontrol 1989 Michelin Laval, QC, H7L 5B7 Phone: With branches in Ville Vanier and Ontario Refrigerative Supply 3958 Myrtle Street, Burnaby, BC, V5C 4G2 Phone: With branches in British Columbia, Alberta, Saskatchewan,Manitoba Regal Controls 1156 Kingsway Vancouver, BC V5V 3C8 Phone: With branch in Langley Regulvar Laval 1985 Boul Industriel Laval, QC, H7S-1P6 Phone: With branches in Sherbrooke, St. Hubert, Lachine, Quebec City Regulvar Ottawa Inc. 170 Laurier Ax West Suite 714 Ottawa, Ontario, K1P-5V6 Phone: With branch in Gatineau Sinclair Supply Street Edmonton, AB, T5H 3P7 Phone: With branches in British Columbia, Alberta, Saskatchewan SCI 3311 Boul Industriel Laval, QC, H7L 4S3 Phone: Wiles & Legault #5-505 Industriel Avenue Ottawa, ON, K1G 0Z1 Phone: Yorkland Controls 2689 Steeles Avenue, W. Downsview, ON, M3J 2Z8 Phone: With branch in Mississauga USA CANADA LATIN AMERICA

84 HVACDivision t.(81) (81)