Belimo is the Worldwide Leader in Fire and Smoke Actuation

Transcription

1 FS Series Fire and Smoke Direct Coupled Actuators Belimo is the Worldwide Leader in Fire and Smoke Actuation Gateway Base II, Hong Kong Belimo first produced actuators for the European fire and smoke damper market in 978. Belimo has consistently offered new technology since entering the market. Since 978 Belimo s market share has grown as actuator variations were released to meet various worldwide requirements. The FSLF and FSAF are the latest models to be introduced for the United States and regions of the world requiring UL 555 and UL 555S listing. Belimo is the dominant fire and smoke actuator manufacturer in Europe today with 80% market share and is growing in the rest of the world. Canary Wharf, London Pier Imports Corporate Headquarters, Fort Worth, TX FS Series At A Glance FSAF4 US * (p. 40) FSAF4-S US (p. 40) FSAF0 US (p. 40) FSAF0-S US (p. 40) FSAF30 US (p. 4) FSAF30-S US (p. 4) FSAF-SR-S US (p. 44) FSNF4 US (p. 46) FSNF4-S US (p. 46) FSNF0 US (p. 46) FSAF-SR US (p. 44) Torque: 33 in-lb 70 in-lb FSNF0-S US (p. 46) FSNF30 US (p.48) FSNF30-S US (p.48) FSLF4 US (p. 50) FSLF4-S US (p. 50) FSLF0 US (p. 50) FSLF0-S US (p. 50) 30 in-lb Power supply: 4 VAC ** 0 VAC 30 VAC Control signal: On/Off Running time motor: <5 sec <75 sec spring: <5 sec <0 sec Built-in auxiliary switch Manual override FSLF30 US (p. 5) FSLF30-S US (p. 5) L /09 - Subject to change. Belimo Aircontrols (USA), Inc. * FSNF30 VAC data sheets are available at ** FSAF4 is 4 VDC also USA CANADA LATIN AMERICA

2 FS Series Fire and Smoke Direct Coupled Actuators A CLOSER LOOK True mechanical spring return the most reliable failsafe. Reverse mount for clockwise or counterclockwise fail-safe. Check damper position easily with clear position indicator. Overload-proof throughout rotation. Easy mechanical stop to adjust angle of rotation (add ZDB-AF US accessory/fsaf and FSNF only). Built-in auxiliary switch is easy to use, offers feedback or signal for additional device (-S models). Manual override crank speeds installation (only on FSAF models). The same 00% steel toothed cold-weld clamp that Belimo uses on all actuators is used on the FS Series. No slipping on damper shafts will occur. Tested at high torque load for a minimum of 0,000 cycles per UL555(S). Reliable DC motor low current draw. Permanently lubricated gears. FSNF and FSLF actuators meet Uniform Building Code (UBC) requirements. L /09 - Subject to change. Belimo Aircontrols (USA), Inc. Belimo actuator is silent when holding at end position. The Belimo Difference Customer Commitment. Extensive product range. Application assistance. Same-day shipments. Free technical support. Five year warranty. Low Installation and Life-Cycle Cost. Easy installation. Accuracy and repeatability. Low power consumption. No maintenance. Long Service Life. Components tested before assembly. Every product tested before shipment. 30+ years direct coupled actuator design USA CANADA LATIN AMERICA 39

3 FSAF0(-S) US, FSAF4(-S) US On/Off, Spring Return, Meets 50 F [ C] for Half Hour, 75 Second Torque min. 33 in-lb, for control of air dampers Technical Data FSAF0(-S) US, FSAF4(-S) US Power supply FSAF0(-S) US 0 VAC ± 0%, 50/60 Hz FSAF4(-S) US 4 VAC ± 0%, 4 VDC -0% +0% Power consumption FSAF0(-S) US running 50/60Hz: 9.5 W, VA,. A holding 3.5 W, 6 VA,.05 A FSAF4(-S) US running 7.5 W, 0 VA,.4 A holding W, 4 VA,.5 A Transformer sizing 0 VA (Class power source 4V only) Electrical connection motor 3 ft, 8 ga, color coded leads / conduit connectors -S models 3 ft, 8 ga, 4 leads appliance cable / conduit connectors Overload protection electronic throughout 0 to 95 rotation Angle of rotation mechanically limited to 95 Torque 33 in-lb [5 Nm] constant Direction of rotation spring reversible with cw/ccw mounting Position indication visual indicator, 0 to 95 (0 is spring return position) Manual override 3mm hex crank (shipped w/actuator) Running time <75 sec. constant, independent of load spring <0 seconds nominal Humidity 5 to 95% RH non-condensing Ambient temperature normal duty - F to F [-30 C to 50 C] safety duty 3 on/off cycles after 30 minutes at ambient temperature of 50 F [ C] Storage temperature -40 F to 76 F [-40 C to 80 C] Housing NEMA type / IP40 Housing material zinc coated metal Gears permanently lubricated Agency listings culus listed to UL873 and CAN/CSA C. No.4 Noise level (max) 45 db (A) spring return 6 db Servicing Maintenance free Quality standard ISO 900, 5 year Belimo warranty Weight (standard / -S model) FSAF0(-S) US 6. / 6.6 lbs (.8 / 3 kg) FSAF4(-S) US 5.7 / 6. lbs (.6 /.8 kg) Application For two position control of UL555S rated dampers in HVAC. Actuator sizing should be done in accordance with the damper manufacturer s specifications. The actuator is mounted directly to a damper shaft or jackshaft 3/8 to.05 in diameter by means of its universal clamp. A crankarm and mounting brackets are available if the actuator cannot be direct coupled to the jackshaft or damper shaft. Square footage of damper operated will depend on make and model of damper. Typically sq.ft. minimum up to 4 sq.ft maximum will be operated for UL555S applications. Operation The FSAF series actuators provide true spring return operation for reliable failsafe application and positive close-off on UL555S dampers. The spring return system provides constant torque to the damper with, and without, power applied to the actuator. The FSAF series provides 95 of rotation and is provided with a graduated position indicator showing 0 to 95. The FSAF has a manual positioning mechanism which allows the setting of any damper position within its 95 of rotation. The actuator is shipped in the zero fail-safe position to provide automatic compression against damper gaskets for tight shut-off. When power is applied, the manual mechanism is released and the actuator drives toward the open position where it stops rotating. The manual override can also be released physically by the use of a crank supplied with the actuator. SAFETY NOTE Screw a conduit fi tting into the actuator s bushing. Jacket the actuator s input and output wiring with suitable fl exible conduit. Properly terminate the conduit in a suitable junction box. Dimensions (Inches [mm]) Standard: /" to.05" Optional* 3/8" to 3/4" 3/8" to 5/8" *with K4 US clamp 0.65" [6.5] 3.5" [8.7].4" [57] 0.39" [0] 0.35" [9] 3.86" [98] 0.9" [5] 3.5" [80].64" [67].97" [50] 0.59" [69] 5.85" [48.5] 0.6" [6.5] 004 D0.93" [49] L /09 - Subject to change. Belimo Aircontrols (USA), Inc. FSAF0-S US, FSAF4-S US Auxiliary Switch xspst 7A resistive,.5a inductive at 0V or 50V, UL Approved, double-insulated, one switch at 0, one adjustable from 30 to USA CANADA LATIN AMERICA

4 FSAF0(-S) US, FSAF4(-S) US On/Off, Spring Return, Meets 50 F [ C] for Half Hour, 75 Second Accessories (AF series accessories may be employed) IND-AF Damper position indicator K4 US Universal clamp for 3/8 to 3/4 shafts K4- US Universal clamp for up to.05 dia. jackshafts K4-H Universal clamp for hexshafts 3/8 to 5/8 KH-AF Crankarm for up to 3/4 round shaft (Series ) KH-AF- Crankarm for up to.05 jackshaft (Series ) KH-AFV V-bolt kit for KH-AF and KH-AF- Tool-0 0 mm wrench ZDB-AF US Angle of rotation limiter ZG-00 Universal mounting bracket ZG-0 Universal mounting bracket ZG-0 Multiple actuator mounting bracket ZG-03 Universal mounting bracket ZG-04 Universal mounting bracket ZG-06 Mounting bracket for Honeywell Mod IV replacement or new crankarm type installations ZG-07 Mounting bracket for Honeywell Mod III or Johnson Series 00 replacement or new crankarm type installations ZG-08 Mounting bracket for Barber Colman MA 3../4.., Honeywell Mod III or IV or Johnson Series 00 replacement or new crankarm type installations ZG-AF Crankarm adaptor kit for AF/NF ZG-AF08 Crankarm adaptor kit for AF/NF ZS-00 Weather shield (metal) ZS-50 Weather shield (polycarbonate) ZS-300 NEMA 4X housing mm form fit square shaft adaptor For an overview of how to apply the accessories, see Belimo Mechanical Accessories and refer to the Belimo Mounting Methods Guide. NOTE: When using FSAFxx (-S) US actuators, only use accessories listed on this page. Wiring Diagrams Provide overload protection and disconnect as required. CAUTION Equipment Damage! Actuators may be connected in parallel. Power consumption and input impedance must be observed. 3 Actuator may also be powered by 4 VDC. 4 No ground connection required. Double insulated. For end position indication, interlock control, fan startup, etc., the 5 FSAF4-S US and FSAF0-S US incorporates two built-in auxiliary switches: x SPST, 7A resistive,.5 VAC, UL Approved, one switch is fi xed at 0, one is adjustable from 30 to 90. Meets UL requirements without the need of an electrical ground connection. Meets culus or UL and CSA Standard requirements without the need of an electrical ground connection. WARNING Live Electrical Components! During installation, testing, servicing and troubleshooting of this product, it may be necessary to work with live electrical components. Have a qualified licensed electrician or other individual who has been properly trained in handling live electrical components perform these tasks. Failure to follow all electrical safety precautions when exposed to live electrical components could result in death or serious injury. Typical Specification Large combination fi re and smoke dampers are to be operated by Belimo FSAF series actuators. Manufacturer shall provide 5 year warranty. L /09 - Subject to change. Belimo Aircontrols (USA), Inc. Actuators shall draw no more than VA at 0V or 4V. Where auxiliary switches are required for signaling, starting fans, or position indication, -S model actuators, damper blade, or proximity switches shall be provided. Smaller dampers shall employ Belimo FSLF or FSNF actuators per damper manufacturer recommendations. FSAF4 US and FSAF0 US W9_08 Auxiliary switch USA CANADA LATIN AMERICA 4

5 FSAF30(-S) US, FSAF4(-S) US On/Off, Spring Return, 50 F [ C] for Half Hour, 75 Second Torque min. 33 in-lb, for control of air dampers Technical Data FSAF30(-S) US, FSAF4(-S) US Power supply FSAF30(-S) US 30 VAC ± 4%, 50/60 Hz FSAF4(-S) US 4 VAC ± 0%, 4 VDC -0% +0% Power consumption FSAF30(-S) US running 50/60Hz: W, VA,.07 A holding 3.5 W, 6 VA,.03 A FSAF4(-S) US running 7.5 W, 0 VA,.4 A holding W, 4 VA,.5A Transformer sizing 0 VA (Class power source 4V only) Electrical connection motor 3 ft, 8 ga, color coded leads / conduit connectors -S models 3 ft, 8 ga, 4 leads appliance cable / conduit connectors Overload protection electronic throughout 0 to 95 rotation Angle of rotation mechanically limited to 95 Torque 33 in-lb [5 Nm] constant Direction of rotation spring reversible with cw/ccw mounting Position indication visual indicator, 0 to 95 (0 is spring return position) Manual override 3mm hex crank (shipped w/actuator) Running time <75 sec. constant, independent of load spring <0 seconds nominal Humidity 5 to 95% RH non-condensing Ambient temperature normal duty - F to F [-30 C to 50 C] safety duty 3 on/off cycles after 30 minutes at ambient temperature of 50 F [ C] Storage temperature -40 F to 76 F [-40 C to 80 C] Housing NEMA type / IP40 with fl exible conduit Housing material zinc coated metal Gears permanently lubricated Agency listings culus listed to UL873 and CAN/CSA C. No.4 Noise level (max) 45 db (A) spring return 6 db Servicing Maintenance free Quality standard ISO 900, 5 year Belimo warranty Weight FSAF30(-S) US 6.9 lbs (3. kg) FSAF4(-S) US 6.0 lbs (.7 kg) Application For two position control of UL555S rated dampers in HVAC. Actuator sizing should be done in accordance with the damper manufacturer s specifications. The actuator is mounted directly to a damper shaft or jackshaft 3/8 to.05 in diameter by means of its universal clamp. A crankarm and mounting brackets are available if the actuator cannot be direct coupled to the jackshaft or damper shaft. Square footage of damper operated will depend on make and model of damper. Typically sq.ft. minimum up to 4 sq.ft maximum will be operated for UL555S applications. Operation The FSAF series actuators provide true spring return operation for reliable failsafe application and positive close-off on UL555S dampers. The spring return system provides constant torque to the damper with, and without, power applied to the actuator. The FSAF series provides 95 of rotation and is provided with a graduated position indicator showing 0 to 95. The FSAF has a manual positioning mechanism which allows the setting of any damper position within its 95 of rotation. The actuator is shipped in the zero fail-safe position to provide automatic compression against damper gaskets for tight shut-off. When power is applied, the manual mechanism is released and the actuator drives toward the open position where it stops rotating. The manual override can also be released physically by the use of a crank supplied with the actuator. SAFETY NOTE Screw a conduit fi tting into the actuator s bushing. Jacket the actuator s input and output wiring with suitable fl exible conduit. Properly terminate the conduit in a suitable junction box. Dimensions (Inches [mm]) Standard: /" to.05" Optional* 3/8" to 3/4" 3/8" to 5/8" *with K4 US clamp 0.65" [6.5] 3.5" [8.7].4" [57] 0.39" [0] 0.35" [9] 3.86" [98] 0.9" [5] 3.5" [80].64" [67].97" [50] 0.59" [69] 5.85" [48.5] 0.6" [6.5] 004 D0.93" [49] L /09 - Subject to change. Belimo Aircontrols (USA), Inc. FSAF30-S US, FSAF4-S US Auxiliary Switch xspst 7A resistive,.5a inductive at 0V or 50V, UL Approved, double-insulated, one switch at <0, one adjustable from >30 to USA CANADA LATIN AMERICA

6 FSAF30(-S) US, FSAF4(-S) US On/Off, Spring Return, 50 F [ C] for Half Hour, 75 Second Accessories (AF series accessories may be employed) IND-AF Damper position indicator K4 US Universal clamp for 3/8 to 3/4 shafts K4- US Universal clamp for up to.05 dia. jackshafts K4-H Universal clamp for hexshafts 3/8 to 5/8 KH-AF Crankarm for up to 3/4 round shaft (Series ) KH-AF- Crankarm for up to.05 jackshaft (Series ) KH-AFV V-bolt kit for KH-AF and KH-AF- Tool-0 0 mm wrench ZDB-AF US Angle of rotation limiter ZG-00 Universal mounting bracket ZG-0 Universal mounting bracket ZG-0 Multiple actuator mounting bracket ZG-03 Universal mounting bracket ZG-04 Universal mounting bracket ZG-06 Mounting bracket for Honeywell Mod IV replacement or new crankarm type installations ZG-07 Mounting bracket for Honeywell Mod III or Johnson Series 00 replacement or new crankarm type installations ZG-08 Mounting bracket for Barber Colman MA 3../4.., Honeywell Mod III or IV or Johnson Series 00 replacement or new crankarm type installations ZG-AF Crankarm adaptor kit for AF/NF ZG-AF08 Crankarm adaptor kit for AF/NF ZS-00 Weather shield (metal) ZS-50 Weather shield (polycarbonate) ZS-300 NEMA 4X housing mm form fit square shaft adaptor For an overview of how to apply the accessories, see Belimo Mechanical Accessories and refer to the Belimo Mounting Methods Guide. NOTE: When using FSAFxx (-S) US actuators, only use accessories listed on this page. Wiring Diagrams Provide overload protection and disconnect as required. CAUTION Equipment Damage! Actuators may be connected in parallel. Power consumption and input impedance must be observed. 3 Actuator may also be powered by 4 VDC. 4 No ground connection required. Double insulated. For end position indication, interlock control, fan startup, etc., the 5 FSAF4-S US and FSAF30-S US incorporates two built-in auxiliary switches: x SPST, 7A resistive,.5 VAC, UL Approved, one switch is fi xed at 0, one is adjustable from 30 to 90. Meets UL requirements without the need of an electrical ground connection. Meets culus or UL and CSA Standard requirements without the need of an electrical ground connection. WARNING Live Electrical Components! During installation, testing, servicing and troubleshooting of this product, it may be necessary to work with live electrical components. Have a qualified licensed electrician or other individual who has been properly trained in handling live electrical components perform these tasks. Failure to follow all electrical safety precautions when exposed to live electrical components could result in death or serious injury. Typical Specification Large combination fi re and smoke dampers are to be operated by Belimo FSAF series actuators. Manufacturer shall provide 5 year warranty. L /09 - Subject to change. Belimo Aircontrols (USA), Inc. Actuators shall draw no more than VA at 30V or 0 VA at 4V. Where auxiliary switches are required for signaling, starting fans, or position indication, -S model actuators, damper blade, or proximity switches shall be provided. Smaller dampers shall employ Belimo FSLF or FSNF actuators per damper manufacturer recommendations. FSAF4 US and FSAF30 US W439_08 Auxiliary switch USA CANADA LATIN AMERICA 43

7 FSAF4-SR(-S) US Proportional, Spring Return, 4 V, to 0 VDC or 4 to 0 ma control signal Operation at 50 F for limited time per UL555S testing Torque min. 33 in-lb, for control of air dampers Technical Data Power supply Power consumption Transformer sizing Electrical connection FSAF4-SR FSAF4-SR(-S) US 4 VAC ± 0% 50/60 Hz 4 VDC ± 0% running 7 W, VA holding 3 W, 5 VA 5 VA (class power source) 3 ft, 8 GA, 4 color coded leads (4V) / conduit connector FSAF4-SR-S 3 ft, 8 GA appliance cable / conduit connector Overload protection electronic throughout 0 to 95 rotation Operating range to 0 VDC, 4 to 0mA Input impedance 00 kω (0. ma), 500 Ω Feedback output U to 0 VDC (max. 0.5 ma) for 95 Angle of rotation mechanically limited to 95 Torque 33 in-lb [5 Nm] constant Direction of rotation spring reversible with cw/ccw mounting The control direction switch is not present. Direct acting only. VDC=Fail-safe position. Position indication visual indicator, 0 to 95 (0 spring return position) Manual override 3mm hex crank (shipped w/actuator) Running time motor <75 sec. constant, independent of load spring < 0 seconds Humidity 5 to 95% RH non-condensing Ambient temperature normal duty - F to F [-30 C to 50 C] safety duty 3 on/off cycles after 30 minutes at ambient temperature of 50 F [ C] Storage temperature -40 F to 76 F [-40 C to 80 C] Housing NEMA type / IP40 Housing material zinc coated metal Agency listings culus to UL873 and CSA C. No Noise level (max) running 45 db (A) Servicing maintenance free Quality standard ISO 900, 5 year Belimo warranty Weight 6.0 lbs (.7 kg.) Application For proportional modulation of UL555S rated dampers in HVAC. Actuator sizing should be done in accordance with the damper manufacturer s specifications. The actuator is mounted directly to a damper shaft or jackshaft up to.05 in diameter by means of its universal clamp. A crankarm and mounting brackets are available if the actuator cannot be direct coupled to the jackshaft or damper shaft. The actuator operates in response to a to 0 VDC, or with the addition of a 500 Ω resistor, a 4 to 0 ma control input from an electronic controller or positioner. A to 0 VDC feedback signal is provided for position indication or master-slave applications. See Application Bulletin for details. Operation The FSAF series actuators provide spring return operation. There is no reversing switch on the FSAF4-SR. It is direct acting only. A reverse acting signal is required if it must spring open while V signal drives it closed. The torque is asymmetrical giving 80 in-lb drive and 33 in-lb spring. The FSAF resets after being driven or springing closed to the 0 position. There is a possible hysteresis of every 000 changes in signal. This can cause a position shift. It is recommended that power or signal be reset once a week. A manual override winder and locking mechanism is provided. If the manual winder is used when the actuator is powered, the actuator will release and drive closed to reset the 0 degree position. The actuator may not be mechanically parallelled or piggybacked. Each damper section should be controlled by a separate actuator. The wire 5 feedback can be used to parallel up to five additional actuators. If less than. V or greater than 9.9V is given wire 3, actuator drives all the way to the respective end stop. The FSAF uses a DC motor which is controlled by a microchip The actuator may be stalled anywhere during its rotation without damage. If power is removed, the damper will spring closed. Interlocks must be provided as necessary for life safety functions and to shut down fan if required. SAFETY NOTE Screw a conduit fi tting into the actuator s bushing. Jacket the actuator s input and output wiring with suitable fl exible conduit. Properly terminate the conduit in a suitable junction box. Dimensions (Inches [mm]) Standard: /" to.05" Optional* 3/8" to 3/4" *with K4 US clamp 0.65" [6.5] 3.86" [98] 3.0" [78] 3.5" [80].4" [57] 0.9" [5] 0.39" [0] 0.35" [9].64" [67] 0.59" [69] 5.85" [48.5] 0.6" [6.5].93" [49] D00(old) L /09 - Subject to change. Belimo Aircontrols (USA), Inc. FSAF4-SR-S US Auxiliary switch x SPDT 7A resistive,.5a inductive at 0/50VAC. UL Approved, double-insulated, one set at =+0, one adjustable 30 to 90.97" [50] USA CANADA LATIN AMERICA

8 FSAF4-SR(-S) US Proportional, Spring Return, 4 V, to 0 VDC or 4 to 0 ma control signal Operation at 50 F for limited time per UL555S testing Accessories (AF series accessories may be employed) IND-AF Damper position indicator K4 US Universal clamp for 3/8 to 3/4 shafts K4- US Universal clamp for up to.05 dia. jackshafts K4-H Universal clamp for hexshafts 3/8 to 5/8 KH-AF Crankarm for up to 3/4 round shaft (Series ) KH-AF- Crankarm for up to.05 jackshaft (Series ) KH-AFV V-bolt kit for KH-AF and KH-AF- Tool-0 0 mm wrench SGA4 Min. and/or max. positioner in NEMA 4 housing SGF4 Min. and/or max. positioner for flush panel mounting ZG-R0 500 Ω resistor for 0 to 0 ma control signal ZDB-AF US Angle of rotation limiter ZG-00 Universal mounting bracket ZG-0 Universal mounting bracket ZG-0 Multiple actuator mounting bracket ZG-03 Universal mounting bracket ZG-04 Universal mounting bracket ZG-06 Mounting bracket for Honeywell Mod IV replacement or new crankarm type installations ZG-07 Mounting bracket for Honeywell Mod III or Johnson Series 00 replacement or new crankarm type installations ZG-08 Mounting bracket for Barber Colman MA 3../4.., Honeywell Mod III or IV or Johnson Series 00 replacement or new crankarm type installations ZG-AF Crankarm adaptor kit for AF/NF ZG-AF08 Crankarm adaptor kit for AF/NF ZS-00 Weather shield (metal) ZS-50 Weather shield (polycarbonate) ZS-60 Explosion-proof housing ZS-300 NEMA 4X housing For an overview of how to apply the accessories, see Belimo Mechanical Accessories and refer to the Belimo Mounting Methods Guide. NOTE: When using FSAF4-SR(-S) US actuators, only use accessories listed on this page. 3 Actuator may also be powered by 4 VDC. 4 No ground connection required. Double insulated. 5 Only connect common to neg. ( ) leg of control circuits. For end position indication, interlock control, fan startup, etc., 6 FSAF4-SR-S US incorporates two built-in auxiliary switches: x SPDT, 7A resistive,.5a inductive 0/50 VAC, UL Approved, one switch is fixed at 0, one is adjustable 30 to 90. Meets UL requirements without the need of an electrical ground connection. The ZG-R0 500 Ω resistor converts the 4 to 0 ma control signal to to 0 VDC. WARNING Live Electrical Components! During installation, testing, servicing and troubleshooting of this product, it may be necessary to work with live electrical components. Have a qualified licensed electrician or other individual who has been properly trained in handling live electrical components perform these tasks. Failure to follow all electrical safety precautions when exposed to live electrical components could result in death or serious injury. W88_08 Typical Specification L /09 - Subject to change. Belimo Aircontrols (USA), Inc. Proportional smoke, and combination fi re and smoke dampers, shall be controlled by Belimo FSAF4-SR actuators. The control signal shall provide proportional damper control in response to a to 0 VDC or, with the addition of a 500 Ω resistor, a 4 to 0 ma control input from an electronic controller or positioner. The actuators must be designed so that they may be used for either clockwise or counter clockwise fail-safe operation. Actuator shall open damper in <75 seconds per UL555S and shall spring closed in under 0 seconds. Actuators shall be UL Approved, have a 5-year warranty, and be manufactured under ISO 900 International Quality Control Standards. Actuators shall be as manufactured by Belimo. Actuators with auxiliary switches must be constructed to meet the requirement for double insulation so an electrical ground connection is not required to meet agency listings. Replacement Application The number one equal or better requirement for use as a replacement for obsolete defective motors is the UL555S listing of the Belimo actuator with the damper for the application. The local authority having jurisdiction sets the requirements since UL has stated that they do not regulate replacements. Wiring Diagrams Proportional control W57_08 Provide overload protection and disconnect as required. CAUTION Equipment Damage! Actuators may be connected in parallel. Power consumption and input impedance must be observed. Auxiliary switch USA CANADA LATIN AMERICA 45

9 FSNF0(-S) US, FSNF4(-S) US On/Off, Spring Return, 350 F for half hour, 5 sec. cycle time Application The type FSNF spring-return actuator is intended for the operation of smoke and combination fire and smoke dampers in ventilation and air-conditioning systems. The actuator will meet requirements of UL555 and UL555S when tested as an assembly with the damper and will meet requirements of UBC for 5 second opening and closing at 350 F. Square footage of damper operated will depend on make and model and the temperature required. Operation Mounting of the actuator to the damper axle shaft or jackshaft (3/8 to.05 ) is via a cold-weld clamp. Teeth in the clamp and V-bolt dig into the metal of both solid and hollow shafts maintaining a perfect connection. The specially designed clamp will not crush hollow shafts. The bottom end of the actuator is held by an anti-rotation strap or by a stud provided by the damper manufacturer. The actuator is mounted in its fail safe position with the damper blade(s) closed. Upon applying power, the actuator drives the damper to the open position. The internal spring is tensioned at the same time. If the power supply is interrupted, the spring moves the damper back to its fail-safe position. Technical Data FSNF0(-S) US, FSNF4(-S) US Power supply FSNF0(-S) US 0 VAC ± 0%, 50/60 Hz FSNF4(-S) US 4 VAC ± 0%, 50/60 Hz Power consumption running 7 VA,.3 A 0 VAC holding 0 VA,.09 A Transformer sizing 4 VAC 7 VA Class power supply Electrical connection FSNF0(-S) US 3 ft, 8 ga, 3 color coded leads FSNF4(-S) US 3 ft, 8 ga, color coded leads FSNF...-S US 3 ft, 8 ga, appliance cable Overload protection Electronic throughout 0 to 95 rotation grounded enclosure, 0V Control microprocessor Angle of rotation 95 Torque 70 in-lb [7.9 Nm] minimum from 3 F to 350 F [0 C to 77 C] Direction of rotation spring can be selected by CCW/CW mounting Position indication visual indicator, 0 to 95 Running time between 3 F and 350 F [0 C to 77 C] motor <75 sec. constant, independent of load spring <0 seconds nominal Humidity 5 to 95% RH non-condensing Ambient temperature 3 F to F [0 C to 50 C] Storage temperature -40 F to 76 F [-40 C to 80 C] Housing NEMA type Housing material zinc coated steel Gears steel, permanently lubricated Agency listings culus listed to UL873 and CAN/CSA C. No. 4 Servicing Maintenance free Quality standard ISO 900 Weight FSNF0(-S) US 6.7 lbs (3.0 kg) FSNF4(-S) US 6.0 lbs (.75 kg) FSNF...-S US +0.5 lbs (+.3 kg) FSNF0-S US, FSNF4-S US Auxiliary Switch xspst 7A resistive,.5a inductive at 0V or 50V, UL Approved, double-insulated, one switch at <0, one adjustable from >30 to 90 SAFETY NOTES The actuator contains no components which the user can replace or repair. /" Threaded Connector Screw a conduit fi tting into the actuator s metal bushing. Jacket the actuator s input wiring with suitable flexible conduit. Properly terminate the conduit in a suitable junction box. 3/8" Flexible Connector Models (-FC Screw Connector) Mount the fl exible conduit into the actuator s metal bushing by means of the provided screw with a torque of. Nm. Jacket the actuator s input wiring with suitable fl exible conduit. Properly terminate the conduit in a suitable junction box. Dimensions (Inches [mm]) Standard: /" to.05" Optional* 3/8" to 3/4" *with K4 US clamp 0.65" [6.5] 3.5" [8.7] 3.86" [98].4" [57] 0.9" [5] 0.39" [0] 0.35" [9] 3.5" [80].64" [67].97" [50] 7.54" [9.6] 0.0" [59] 5.85" [48.5] 0.6" [6.5] Accessories All AF/NF linkages and parts may be employed. ø.6" [ø4.] 0.9" [5].93" [49] -S models only.89" [73.5] L /09 - Subject to change. Belimo Aircontrols (USA), Inc USA CANADA LATIN AMERICA

10 FSNF0(-S) US, FSNF4(-S) US On/Off, Spring Return, 350 F for half hour, 5 sec. cycle time Typical Applications Multi-section Damper Assemblies The typical fi re and smoke damper requires from 5-5 in-lb of torque per square foot at 50 F 350 F under dynamic load (400 fpm velocity). The FSNF will operate multi-section dampers using multiple actuators for multiple sections. Some of the methods used are shown below. This is a direct coupled actuator. If linkages are needed use the FSNF series. Square shaft adaptors are available: , , for the 8mm, 0mm, and mm, form fi t respectively. Wiring Diagrams Provide overload protection and disconnect as required. 4 CAUTION Equipment Damage! Actuators may be connected in parallel. Power consumption and input impedance must be observed. For end position indication, interlock control, fan startup, etc., FSNF4-S US and FSNF0-S US incorporate two built-in auxiliary switches: x SPDT, 7A (.5A inductive)@5/50 VAC, UL Approved, 5 and 85. Switch rating is for 50F / hour only. Single section for one FSNF actuator Blank-off Channel Blank-off Channel Meets culus or UL and CSA Standard requirements without the need of an electrical ground connection. WARNING Live Electrical Components! During installation, testing, servicing and troubleshooting of this product, it may be necessary to work with live electrical components. Have a qualified licensed electrician or other individual who has been properly trained in handling live electrical components perform these tasks. Failure to follow all electrical safety precautions when exposed to live electrical components could result in death or serious injury. Use of blank-offs between damper sections to provide space for actuator mounting. Large multi-section assembly Wht Blk 4V C H 0V N L Neutral Hot 3 Ground W77 Typical Specification Smoke Control and Combination Fire and Smoke Control Damper Actuators No ground on 4 V models FSNF4 US FSNF0 US L /09 - Subject to change. Belimo Aircontrols (USA), Inc. All smoke and combination fi re and smoke dampers shall be provided with Belimo FSLF, FSNF, or FSAF actuators. No substitutions allowed. Damper and actuator shall have UL555S Listing for 50 F (350 F) and shall comply with UBC if required by local codes. Where proof of closure switches are required, blade switches, actuator auxiliary switches, or proximity switches are allowed. Replacement Applications The number one "equal or better" requirement for use as a replacement for obsolete defective motors is the UL555S listing of the Belimo actuator with the damper for the application. The local authority having jurisdiction sets the requirements. In some cases a permit and inspection may be required. Contact Belimo for a list of damper manufacturers with UL555S listing with Belimo FSAF, FSLF, & FSNF actuators. CAUTION Caution must be used when replacing failed motors with new Belimo actuators. Many old motors did not have internal springs and depended on external springs on the side of the damper or wrapped around the damper shaft to close the damper. In some cases, the damper must be replaced because the damper would have to undergo major modifications to replace an actuator. Wht Blk 4V C H 0V N L Parallel Actuator Wiring Gnd Gnd No ground on 4 V models FSNF Multi-Sec ApplicBLK W75_08 In many cases, replacing the actuator voids the UL555S listing of the damper. Auxiliary switch wiring for FSNF4-S US, FSNF0-S US USA CANADA LATIN AMERICA 47

11 FSNF30(-S) US, FSNF4(-S) US On/Off, Spring Return, 350 F [77 C] for limited time, nominal 5 sec. operation Technical Data FSNF30(-S) US, FSNF4(-S) US Power supply FSNF30(-S) US 30 VAC ± 0%, 50/60 Hz FSNF4(-S) US 4 VAC ± 0%, 50/60 Hz Power consumption running 8 W, 7 VA,.3 A 30 VAC holding 6 W, 0 VA,.04 A Transformer sizing 4 VAC 7 VA Class power supply Electrical connection FSNF30(-S) US 3 ft [m], 8 ga, 3 color coded leads FSNF4(-S) US 3 ft [m], 8 ga, color coded leads FSNF...-S US 3 ft [m], 8 ga, appliance cable Overload protection Electronic throughout 0 to 95 rotation auto-restart after temporary overload Electrical protection grounded enclosure, 30V Control microprocessor Angle of rotation 95 Torque 70 in-lb [7.9 Nm] minimum from 3 F to 350 F [0 C to 77 C] Direction of rotation spring can be selected by CCW/CW mounting Position indication visual indicator, 0 to 95 Running time between 3 F and 350 F [0 C to 77 C] motor approx. 5 sec at rated voltage and torque spring approx. 5 sec Humidity 5 to 95% RH non-condensing Ambient temperature 3 F to F [0 C to 50 C] Storage temperature -40 F to 76 F [-40 C to 80 C] Housing NEMA type Housing material zinc coated steel Gears steel, permanently lubricated Agency listings culus listed to UL873 and CAN/CSA C. No. 4 Servicing Maintenance free Quality standard ISO 900 Weight FSNF30(-S) US 6.7 lbs (3.0 kg) FSNF4(-S) US 6.0 lbs (.75 kg) FSNF...-S US +0.5 lbs (+.3 kg) Application The type FSNF spring-return actuator is intended for the operation of smoke and combination fire and smoke dampers in ventilation and air-conditioning systems. The actuator will meet requirements of UL555 and UL555S when tested as an assembly with the damper and will meet requirements of UBC for 5 second opening and closing. Square footage of damper operated will depend on make and model and the temperature required. Operation Mounting of the actuator to the damper shaft or jackshaft (3/8 to.05 ) is via a cold-weld clamp. Teeth in the clamp and V-bolt dig into the metal of both solid and hollow shafts maintaining a perfect connection. The specially designed clamp will not crush hollow shafts. The bottom end of the actuator is held by an anti-rotation strap or by a stud provided by the damper manufacturer. The actuator is mounted in its fail safe position with the damper blade(s) closed. Upon applying power, the actuator drives the damper to the open position. The internal spring is tensioned at the same time. If the power supply is interrupted, the spring moves the damper back to its fail-safe position. SAFETY NOTES The actuator contains no components which the user can replace or repair. /" Threaded Connector Screw a conduit fi tting into the actuator s metal bushing. Jacket the actuator s input wiring with suitable flexible conduit. Properly terminate the conduit in a suitable junction box. 3/8" Flexible Connector Models (-FC Screw Connector) Mount the fl exible conduit into the actuator s metal bushing by means of the provided screw with a torque of. Nm. Jacket the actuator s input wiring with suitable fl exible conduit. Properly terminate the conduit in a suitable junction box. Dimensions (Inches [mm]) Standard: /" to.05" Optional* 3/8" to 3/4" *with K4 US clamp 0.65" [6.5] 3.5" [8.7] 3.86" [98].4" [57] 0.9" [5] 0.39" [0] 0.35" [9] 3.5" [80].64" [67].97" [50] 7.54" [9.6] 0.0" [59] 5.85" [48.5] 0.6" [6.5] Accessories All AF/NF linkages and parts may be employed. Order part for square shafts. ø.6" [ø4.] 0.9" [5].93" [49] -S models only.89" [73.5] L /09 - Subject to change. Belimo Aircontrols (USA), Inc. FSNF30-S US, FSNF4-S US Auxiliary Switch x SPDT 7A (.5A inductive)@ 5/50VAC, UL Approved, 5 and 85, double insulated USA CANADA LATIN AMERICA

12 FSNF30(-S) US, FSNF4(-S) US On/Off, Spring Return, 350 F [77 C] for limited time, nominal 5 sec. operation Typical Applications Multi-section Damper Assemblies The typical US fi re-smoke damper requires from 5-5 in-lb torque per square ft. [6-7 Nm per square meter] at 350 F [7 C] under dynamic load (400 fpm [m/s] velocity). Some of the methods used for multi-section dampers with the FSNF actuators are shown below. Wiring Diagrams Provide overload protection and disconnect as required. CAUTION Equipment Damage! Actuators may be connected in parallel. Power consumption and input impedance must be observed. For end position indication, interlock control, fan startup, etc., 4 FSNF4-S and FSNF30-S incorporate two built-in auxiliary switches: x SPDT, 7A (.5A inductive)@5/50 VAC, UL Approved, 5 and 85. Switch rating 50 F [ C] / hour only. Single section for one FSNF actuator Blank-off Channel Meets culus or UL and CSA Standard requirements without the need of an electrical ground connection. Blank-off Channel WARNING Live Electrical Components! During installation, testing, servicing and troubleshooting of this product, it may be necessary to work with live electrical components. Have a qualified licensed electrician or other individual who has been properly trained in handling live electrical components perform these tasks. Failure to follow all electrical safety precautions when exposed to live electrical components could result in death or serious injury. Use of blank-offs between damper sections to provide space for actuator mounting. Large multi-section assembly W9_08 Typical Specification Smoke Control and Combination Fire and Smoke Control Damper Actuators All smoke and combination fi re and smoke dampers shall be provided with Belimo FSLF, FSNF, or FSAF actuators. No substitutions allowed. L /09 - Subject to change. Belimo Aircontrols (USA), Inc. Damper and actuator shall have UL555S Listing for 50 F (350 F) and shall comply with UBC if required by local codes. Where proof of closure switches are required, blade switches, actuator auxiliary switches, or proximity switches are allowed. Replacement Applications The number one "equal or better" requirement for use as a replacement for obsolete defective motors is the UL555S listing of the Belimo actuator with the damper for the application. The local authority having jurisdiction sets the requirements. In some cases a permit and inspection may be required. Contact Belimo for a list of damper manufacturers with UL555S listing with Belimo FSAF, FSLF, & FSNF actuators. CAUTION Caution must be used when replacing failed motors with new Belimo actuators. Many old motors did not have internal springs and depended on external springs on the side of the damper or wrapped around the damper shaft to close the damper. In some cases, the damper must be replaced because the damper would have to undergo major modifi cations to replace an actuator. In many cases, replacing the actuator voids the UL555S listing of the damper. Wht Blk 4V C H 30V Eu US 3Φ N L L L Parallel Actuator Wiring Gnd g Gnd No ground on 4 V models S S S3 S4 S5 NC NO NC 5 4 FSNF Multi-Sec ApplicBLK30 W436_08 S6 NO 85 FSNF4-S US FSNF30-S US Auxiliary switch wiring for FSNF4-S US, FSNF30-S US USA CANADA LATIN AMERICA 49

13 FSLF0(-S) US, FSLF4(-S) US On/Off, Spring Return, 350 F [77 C] for half hour, 5 sec. operation Technical Data FSLF0(-S) US, FSLF4(-S) US Power supply FSLF0(-S) US 0 VAC, 50/60 Hz nominal voltage range 08-3 VAC FSLF4(-S) US 4 VAC, 50/60 Hz nominal voltage range VAC Power consumption 0 VAC running 50 Hz, 0 VA / 60 Hz, 8 VA holding 50 Hz, VA / 60 Hz, 6.5 VA 4 VAC running 50/60 Hz, 5.0 VA holding 50/60 Hz, 3.5 VA Transformer sizing Safety Note, connect via safety isolating 4 VAC transformer, class supply Electrical connection FSLF0(-S) US 3 ft [m], 8 ga, 3 color coded leads FSLF4(-S) US 3 ft [m], 8 ga, color coded leads FSLF...-S US 3 ft [m], 8 ga, appliance cable Overload protection Electronic throughout 0 to 95 rotation auto-restart after temporary overload Electrical protection grounded enclosure, 0V Control microprocessor Angle of rotation 95 Torque 30 in-lb [3.5 Nm] minimum from 3 F to 350 F [0 C to 77 C] Direction of rotation spring can be selected by CCW/CW mounting Position indication visual indicator, 0 to 95 Running time motor < 5 sec at rated voltage and torque 3 F and F [0 C to 50 C] spring < 5 sec at ambient temperature Humidity 5 to 95% RH non-condensing Ambient temperature normal duty 3 F to F [0 C to 50 C] safety duty 3 on/off cycles after 30 minutes at ambient temperature of 350 F [77 C] Storage temperature -40 F to 76 F [-40 C to 80 C] Housing NEMA type, zinc coated steel Type of action Type.B Software class A Shaft 3/8 -/ rnd (7/6 sq) / -3/4 rnd w/k6- Gears permanently lubricated Agency listings culus listed to UL and CAN/CSA. No 4 Servicing Maintenance free Quality standard ISO 900 Weight FSNF30(-S) US 4.0 lbs (.8 kg) FSNF4(-S) US 3.4 lbs (.7 kg) FSNF...-S US +0.3 lbs (+.4 kg) Application: The type FSLF spring-return actuator is intended for the operation of smoke and combination fire and smoke dampers in ventilation and air-conditioning systems. The actuator will meet requirements of UL555 and UL555S when tested as an assembly with the damper and will meet requirements of UBC for 5 second opening and closing. Square footage of damper operated will depend on make and model and the temperature required. Operation Mounting of the actuator to the damper axle shaft or jackshaft is via a cold-weld clamp. Teeth in the clamp and V-bolt dig into the metal of both solid and hollow shafts maintaining a perfect connection. The specially designed clamp will not crush hollow shafts. The bottom end of the actuator is held by an anti-rotation strap or by a stud provided by the damper manufacturer. The actuator is mounted in its fail safe position with the damper blade(s) closed. Upon applying power, the actuator drives the damper to the open position. The internal spring is tensioned at the same time. If the power supply is interrupted, the spring moves the damper back to its fail-safe position. SAFETY NOTES The actuator contains no components which the user can replace or repair. /" Threaded Connector Screw a conduit fi tting into the actuator s metal bushing. Jacket the actuator s input wiring with suitable flexible conduit. Properly terminate the conduit in a suitable junction box. 3/8" Flexible Connector Models (-FC Screw Connector) Mount the fl exible conduit into the actuator s metal bushing by means of the provided screw with a torque of. Nm. Jacket the actuator s input wiring with suitable fl exible conduit. Properly terminate the conduit in a suitable junction box. Dimensions (Inches [mm]).37" [60] 0. [5] 0.45" FSLF0-S US, FSLF4-S US Auxiliary Switch [] 7.03" [79] 6.8" [73] 5.4" [38]." [8] max 0.79" [0] min 0.5" [.7] 0.75" [9].4" [57] 0.4" [6] 3.86" " [98] x SPST 0.5 A 0/50 V, 5 VDC, 3 A 0/50 V, UL Approved, 0 and 85, double insulated L /09 - Subject to change. Belimo Aircontrols (USA), Inc USA CANADA LATIN AMERICA

14 FSLF0(-S) US, FSLF4(-S) US On/Off, Spring Return, 350 F [77 C] for half hour, 5 sec. operation Typical Applications Multi-section Damper Assemblies The typical fi re and smoke damper requires from 5-5 in-lb of torque per square foot at 50 F F under dynamic load (000 fpm velocity). The FSLF is a single section damper actuator. For the multi section dampers, use the FSNF series. This is a direct coupled actuator. If linkages are needed use the FSNF series. Square shaft adaptors are available: , , for the 8mm, 0mm, and mm, form fi t respectively. Wiring Diagrams Provide overload protection and disconnect as required. CAUTION Equipment Damage! Actuators may be connected in parallel. Power consumption and input impedance must be observed. 3 No ground connection required. Double insulated. For end position indication, interlock control, fan startup, etc., 4 FSNF4-S and FSNF30-S incorporate two built-in auxiliary switches: x SPDT, 7A (.5A inductive)@5/50 VAC, UL Approved, 5 and 85. Switch rating 50 F [ C] / hour only. Single section for one FSLF actuator Two section for two FSLF actuators Meets culus or UL and CSA Standard requirements without the need of an electrical ground connection. WARNING Live Electrical Components! During installation, testing, servicing and troubleshooting of this product, it may be necessary to work with live electrical components. Have a qualified licensed electrician or other individual who has been properly trained in handling live electrical components perform these tasks. Failure to follow all electrical safety precautions when exposed to live electrical components could result in death or serious injury. Maximum area one actuator Maximum area for two actuators 4V C=Blk H=Red 0V N=Wht L=Blk Common, Neutral Hot W0 Typical Specification Smoke Control and Combination Fire and Smoke Control Damper Actuators All smoke and combination fi re and smoke dampers shall be provided with Belimo FSLF, FSNF, or FSAF actuators. No substitutions allowed. No ground on 4 V models 3 Ground FSLF4 US FSLF0 US Damper and actuator shall have UL555S Listing for 50 F (350 F) and shall comply with UBC if required by local codes. L /09 - Subject to change. Belimo Aircontrols (USA), Inc. Where proof of closure switches are required, blade switches, actuator auxiliary switches, or proximity switches are allowed. Replacement Applications The number one "equal or better" requirement for use as a replacement for obsolete defective motors is the UL555S listing of the Belimo actuator with the damper for the application. The local authority having jurisdiction sets the requirements. Contact Belimo for a list of damper manufacturers with UL555S listing with Belimo FSAF, FSNF, & FSLF actuators. CAUTION Caution must be used when replacing failed motors with new Belimo actuators. Many old motors did not have internal springs and depended on external springs on the side of the damper or wrapped around the damper shaft to close the damper. In some cases, the damper must be replaced because the damper would have to undergo major modifi cations to replace an actuator. 4V 0V C=Blk N=Wht H=Red L=Blk Parallel Actuator Wiring Gnd Gnd No ground on 4 V models W00 Most codes require that equal or better actuators be used to replace defectives. Auxiliary switch wiring for FSLF4-S US, FSLF0-S US USA CANADA LATIN AMERICA 5

15 FSLF30(-S) US, FSLF4(-S) US On/Off, Spring Return, 350 F [77 C] for half hour, 5 sec. operation Technical Data FSLF30(-S) US, FSLF4(-S) US Power supply FSLF30(-S) US 30 VAC, 50/60 Hz nominal voltage range VAC FSLF4(-S) US 4 VAC, 50/60 Hz nominal voltage range VAC Power consumption 30 VAC running 50 Hz, 7 VA / 60 Hz, 7 VA holding 50 Hz, 8 VA / 60 Hz, 6 VA 4 VAC running 50/60 Hz, 5.0 VA holding 50/60 Hz, 3.5 VA Transformer sizing Safety Note, connect via safety isolating 4 VAC transformer, class supply Electrical connection FSLF30(-S) US 3 ft [m], 8 ga, 3 color coded leads FSLF4(-S) US 3 ft [m], 8 ga, color coded leads FSLF...-S US 3 ft [m], 8 ga, appliance cable Overload protection Electronic throughout 0 to 95 rotation auto-restart after temporary overload Electrical protection grounded enclosure, 30V Control microprocessor Angle of rotation 95 Torque 30 in-lb [3.5 Nm] minimum from 3 F to 350 F [0 C to 77 C] Direction of rotation spring can be selected by CCW/CW mounting Position indication visual indicator, 0 to 95 Running time motor < 5 sec at rated voltage and torque 3 F and F [0 C to 50 C] spring < 5 sec Humidity 5 to 95% RH non-condensing Ambient temperature normal duty 3 F to F [0 C to 50 C] safety duty 3 on/off cycles after 30 minutes at ambient temperature of 350 F [77 C] Storage temperature -40 F to 76 F [-40 C to 80 C] Housing NEMA type / IP0, zinc coated steel Type of action Type.B Software class A Shaft 3/8 -/ rnd (7/6 sq) / -3/4 rnd w/k6- Gears permanently lubricated Agency listings culus listed to UL and CAN/CSA. No 4 Servicing Maintenance free Quality standard ISO 900 Weight FSNF30(-S) US 4.0 lbs (.8 kg) FSNF4(-S) US 3.4 lbs (.7 kg) FSNF...-S US +0.3 lbs (+.4 kg) Application The type FSLF spring-return actuator is intended for the operation of smoke and combination fire and smoke dampers in ventilation and air-conditioning systems. The actuator will meet requirements of UL555 and UL555S when tested as an assembly with the damper and will meet requirements of UBC for 5 second opening and closing. Square footage of damper operated will depend on make and model and the temperature required. Operation Mounting of the actuator to the damper axle shaft or jackshaft is via a cold-weld clamp. Teeth in the clamp and V-bolt dig into the metal of both solid and hollow shafts maintaining a perfect connection. The specially designed clamp will not crush hollow shafts. The bottom end of the actuator is held by an anti-rotation strap or by a stud provided by the damper manufacturer. The actuator is mounted in its fail safe position with the damper blade(s) closed. Upon applying power, the actuator drives the damper to the open position. The internal spring is tensioned at the same time. If the power supply is interrupted, the spring moves the damper back to its fail-safe position. SAFETY NOTES The actuator contains no components which the user can replace or repair. /" Threaded Connector Screw a conduit fi tting into the actuator s metal bushing. Jacket the actuator s input wiring with suitable flexible conduit. Properly terminate the conduit in a suitable junction box. 3/8" Flexible Connector Models (-FC Screw Connector) Mount the fl exible conduit into the actuator s metal bushing by means of the provided screw with a torque of. Nm. Jacket the actuator s input wiring with suitable fl exible conduit. Properly terminate the conduit in a suitable junction box. Dimensions (Inches [mm]).37" [60] 0. [5] 0.45" FSLF30-S US, FSLF4-S US Auxiliary Switch [] 7.03" [79] 6.8" [73] 5.4" [38]." [8] max 0.79" [0] min 0.5" [.7] 0.75" [9].4" [57] 0.4" [6] 3.86" " [98] x SPST 0.5 A 0/50 V, 5 VDC, 3 A 0/50 V, UL Approved, 0 and 85, double insulated L /09 - Subject to change. Belimo Aircontrols (USA), Inc USA CANADA LATIN AMERICA