AM Series Direct Coupled Actuator

Transcription

1 AM Series Direct Coupled Actuator Versatile and Powerful Minimum 60 in-lb torque in a compact package. For damper areas up to 0 sq-ft*. Areas of Application Direct Coupled up to / standard shafts or Jackshafts to.0 (with K- Clamp) Mounting with linkage (ZG-AM accessory kit) /" min Short shaft mounting (with AV clamp) AV Kit specification ball joints KG8 (00) Spacer (7) Crank arm (6) Front mounting bracket (67) ear mounting bracket (06) Screws M6 x 6 (600) 7 Self-tapping screws, x (990) Fits Jackshafts also. Actuators in bold have DCM AM Series at a glance Torque: 60 in-lb in-lb Power supply: VAC/DC Control signal: on-off/floating On/Off proportional to 0 VDC 0 Ω or Honeywell Electronic Series 90 0 to 0 V phasecut Multi-function** Feedback: to 0 VDC VDC variable** unning time motor: 0 sec constant 0 to 0 sec load dependent Adj. 7 to 00 sec*** load dependent 6 to 9 sec load dependent AM US (p. 8) External direction of rotation switch Conduit fitting Appliance cable uilt-in auxiliary switches UL listed, CSA certified, CE Auxiliary switches and feedback potentiometer(p.9-0) Installation instructions...(p. -) General wiring...(p. ) Start-up and checkout (p. 6) AM-S US (p. 8) AM-S US (p. 0) AM-PC US (p. ) AM-MFT US (p. ) AM-MFT9 US (p.6) SM-S US (p. 8) G09-IG-Subject to change. elimo Aircontrols (USA), Inc. *ased on in-lb/ft damper torque loading. Parallel blade. No edge seals. **Default to 0 VDC. ***Default 0 seconds. 6

2 AM Series Direct Coupled Actuator A CLOSE LOOK LISTED 9D TEMP. IND & EG. EQUIP. UL 0% more torque than SM. Fits inside damper frame. Full stroke overload protection. Electronic deadband for accuracy and stability (modulating actuators). Easy direct coupled mounting, including jackshafts to.0. Check damper position with clear position indicator. Set actuator to compensate for damper seal wear and compression (modulating actuators). Constant running time aids control loop tuning (modulating actuators). AM Added flexibility with built-in mechanical stops. Fully adjustable, built-in auxiliary switches (AM-S US only). Auxiliary switch add-on mounts on clamp, includes conduit fitting (SA US, SA US). Push button manual override Easily reverse control direction with switch on housing G09-Subject to change. elimo Aircontrols (USA), Inc. cable speeds installations Micro processor controlled rushless DC Motor The elimo Difference Customer Commitment. Extensive product range. Application assistance. Same-day shipments. Free technical support. Five year warranty. Low Installation and Life-Cycle Cost. Easy installation. Accuracy and repeatability. Low power consumption. No maintenance. Long Service Life. Components tested before assembly. Every product tested before shipment. 0+ years direct coupled actuator design. 7

3 AM (-S) US On-off/ floating point control, non-spring return, direct coupled, V Torque min. 60 in-lb, for control of air dampers. AM US AM-S US Application For on-off and floating point control of dampers in HVAC systems. Actuator sizing should be done in accordance with the damper manufacturer s specifications. LISTED 9D TEMP. IND & EG. EQUIP. UL The actuator is mounted directly to a damper shaft up to.0 in diameter by means of its universal clamp. A crankarm and several mounting brackets are available for applications where the actuator cannot be direct coupled to the damper shaft. AM US Operation The actuator is not provided with and does not require any limit switches, but is electronically protected against overload. The angle of rotation is mechanically limited to 9. hen reaching the damper or actuator end position, the actuator automatically stops. The gears can be manually disengaged with a button on the actuator cover. The position of the actuator is indicated by a visual pointer. The anti-rotation strap supplied with the actuator will prevent lateral movement. Technical Data AM US, AM-S US Power supply VAC ± 0% 0/60 Hz VDC ± 0% Power consumption running:. ; holding:. Transformer sizing. VA (Class power source) The AM-S US version is provided with two built-in auxiliary switches. These SPDT switches are provided for safety interfacing or signaling. The switching function is adjustable between 0 and 9. Electrical connection ft, 8 GA, appliance cable, / conduit connector Overload protection electronic throughout 0 to 9 rotation Angle of rotation Torque Direction of rotation Position indication unning time Manual override Humidity Ambient temperature Storage temperature Housing type Housing material rating Noise level 0 to 9, adjust with mechanical stops min 60 in-lb [8 Nm] reversible with switch C/CC clip-on indicator 0 to 0 sec. for 0 to 60 in-lb external push button to 9% H, non-condensing - F to + F [-0 C to +0 C] -0 F to +76 F [-0 C to +80 C] NEMA (IP with cable entry down) UL9-V (flammability rating) less than d (A) Servicing maintenance free Agency listings UL 87 listed, CSA C. No. certified, CE Quality standard ISO 900 eight.8 lbs [. kg] Dimensions [All numbers in brackets are in millimeters.] K- US (supplied) /" Centered (Default) /" Centered (Field Selectable).0" Centered (Field Selectable) K- US (optional) /" to.0" Adjustable.0" [76] 8.7" [] 7." [9].8" [6].90" [].77" [] G09-IG-Subject to change. elimo Aircontrols (USA), Inc. AM-S US Auxiliary switches adj. 0 to 9, x SPDT A VAC K US (optional) /8" to /" Adjustable.6" [9] D0 8

4 AM (-S) US On-off/ floating point control, non-spring return, direct coupled, V Accessories AV Damper shaft extension for AM AV0-8 Universal shaft extension K US Universal clamp for /8 to / shafts K- US Clamp for / to.0 jackshafts K-H Hex shaft clamp, for /8 -/8 shafts KH-AM Crankarm SA US, SA US Auxiliary switches PA US 0 Ω, 00 Ω, 000 Ω, 800 Ω feedback potentiometers Tool-06 8mm and 0 mm wrench ZA-AM US SM to AM retrofit bracket ZG-AM US Crank arm adaptor kit ZG-00 Mounting bracket ZG-0 Mounting bracket ZG-0 Mounting bracket ZG-0 Mounting bracket ZS-00 eather shield (metal) ZS-0 eather shield (polycarbonate) ZS-60 Explosion-proof housing ZS-00 NEMA X housing AM (-S) US - Typical Specification: Control damper actuators shall be electronic direct coupled type which require no crank arm and linkage and be capable of direct mounting to a jackshaft up to a.0 diameter. Actuators shall be UL and CSA listed, have a year warranty, and be manufactured under ISO 900 International Quality Control Standards. Actuators shall have reversing switch and manual override on the cover, and be protected from overload at all angles of rotation. If required, two adjustable SPDT auxiliary switches shall be provided (AM-S US). Actuators shall be as manufactured by elimo. NOTE: hen using AM-(-S) US actuators, use only the accessories listed on this page. AM iring diagrams G09-Subject to change. elimo Aircontrols (USA), Inc. VAC Transformer a open a closed The indication of direction is valid for switch position C. On-off control VAC Transformer The indication of direction is valid for switch position C. a lk () Common ht () + ht () + CC C AM (-S) US lk () Common ht () + ht () + CC C AM (-S) US S S S S S S6 Auxiliary switch wiring for AM-S US Notes NC NO NC NO 0 to 9 0 to 9 AM (-S) US Provide overload protection and disconnect as required. Actuators may also be powered by VDC. For end position indication, interlock control, fan startup, etc., AM-S US incorporates two built-in auxiliary switches: x SPDT, A VAC, UL listed, adjustable between 0 and Floating point or on-off control Meets UL and CSA requirements without the need of an electrical ground connection. 9

5 AM-S US Proportional damper actuator, non-spring return, direct coupled, V, for to 0 VDC and to 0 ma control signal Torque min. 60 in-lb, for control of air dampers. Application For proportional modulation of dampers in HVAC systems. Actual actuator sizing should be done in accordance with the damper manufacturer s specifications. The actuator is mounted directly to a damper shaft up to.0 in diameter by means of its universal clamp. A crankarm and several mounting brackets are available for applications where the actuator cannot be direct coupled to the damper shaft. LISTED 9D TEMP. IND & EG. EQUIP. UL Operation The actuator operates in response to a to 0 VDC, or, with the addition of a 00Ω resistor, a to 0 ma control input from an electronic controller or positioner. A to 0 VDC feedback signal is provided for position indication or master-slave applications. Technical Data Power supply Power consumption Transformer sizing Operating range Y Input impedance Feedback output 'U' Electrical connection Overload protection Torque Direction of rotation Position indication Manual override Angle of rotation unning time un time stability ± % Humidity AM-S US VAC, ± 0%, 0/60 Hz VDC, ±0% running:. ; holding:. VA (Class power source) to 0 VDC, to 0 ma 00kΩ (0. ma), 00Ω for to 0mA to 0 VDC, 0. ma max ft, 8 GA, appliance cable, / conduit connector electronic throughout 0 to 9 rotation min 60 in-lb (8 Nm) reversible with switch C/CC C with a decrease in voltage CC with a decrease in voltage clip on indicator external push button 0 to 9, adjust with mechanical stops 0 secs. constant, independent of load to 9% H, non-condensing Operating temperature - to + F (-0 to +0 C) Storage temperature -0 to +76 F (-0 to +80 C) Housing Housing material NEMA (IP with cable entry down) UL 9-V (flammability rating) Noise level less than d (A) Agency listings UL 87 listed, CSA C. No. certified, CE Quality standard ISO 900 Servicing maintenance free eight.8 lbs. (.kg.) AM-S US The actuator has a constant running time of 0 seconds. A functional test of the actuator-damper assembly may be done by pressing in the manual override button, this will activate the actuators test mode and cycle the actuator fully closed and back to control point. The microprocessor will correct for compression of tight close-off gaskets with age, providing the actuator is not on its mechanical stops. A to 0 VDC feedback (U) is provided with full 8 volt output range proportional to the operational rotation of the damper. A digital rotation sensing circuit protects the actuator in a stall anywhere in its 9 operating range without the need of limit switches. Add on auxiliary switches are easily fastened directly onto the actuator body for signalling and switching functions. Dimensions [All numbers in brackets are in millimeters.] K- US (supplied) /" Centered (Default) /" Centered (Field Selectable).0" Centered (Field Selectable) K- US (optional) /" to.0" Adjustable K US (optional) /8" to /" Adjustable.0" [76] 8.7" [] 7." [9].8" [6].90" [].77" [].6" [9] D007 G09-IG-Subject to change. elimo Aircontrols (USA), Inc. 0

6 AM-S US Proportional damper actuator, non-spring return, direct coupled, V, for to 0 VDC and to 0 ma control signal Accessories AV Damper shaft extension for AM AV0-8 Universal shaft extension K US Universal clamp for /8 to / shafts K- US Clamp for / to.0 jackshafts K-H Hex shaft clamp, for /8 -/8 shafts KH-AM Crankarm SA US, SA US Auxiliary switches PA US 0 Ω, 00 Ω, 000 Ω, 800 Ω feedback potentiometers PTA-0 Pulse width modulation interface Tool-06 8mm and 0 mm wrench SGA Min. and/or man. positioner in NEMA housing SGF Min. and/or man. positioner for flush panel mounting ZG-0 00Ω resistor for to 0 ma control signal ZA-AM US SM to AM retrofit bracket ZG-AM US Crank arm adaptor kit ZG-00 Mounting bracket ZG-0 Mounting bracket ZG-0 Mounting bracket ZG-0 Mounting bracket ZS-00 eather shield ZS-0 eather shield ZS-60 Explosion-proof housing ZS-00 NEMA X housing AM-S US - Typical Specification: Control damper actuators shall be electronic direct coupled type which require no crank arm and linkage and be capable of direct mounting to a jackshaft up to a.0 diameter. Actuators shall be UL and CSA listed, have a year warranty, and be manufactured under ISO 900 International Quality Control Standards. The actuator must provide proportional damper control in response to a to 0 VDC, or, with the addition of a 00Ω resistor, a to 0 ma control input from an electronic controller or positioner. Actuators shall have reversing switch and gear disengagement button on the cover, and be electronically protected from overload at all angles of rotation. Actuators shall respond to to 0VDC output relative to position regardless of the amount of damper rotation. un time shall be constant and independent of torque. A to 0 VDC feedback signal shall be provided for position indication or master-slave applications. Actuators shall be as manufactured by elimo. AM NOTE: hen using AM-S US actuators, use only the accessories listed on this page. iring diagrams VAC Transformer 077 lk () Common ed () Hot + G09-Subject to change. elimo Aircontrols (USA), Inc. Control Signal ( ) to 0 VDC (+) VAC Transformer to 0 ma Control Signal to 0 VDC Feedback Signal ( ) (+) ( ) (+) Ω 00Ω To other actuators ht () Y Input, to 0V ht () U Output, to 0V AM-S US Provide overload protection and disconnect as required. Actuators may be connected in parallel. Power consumption and input impedance must be observed. Actuator may also be powered by VDC. The ZG-0 00Ω resistor converts the to 0 ma control signal to to 0 VDC, up to actuators may be connected in parallel. Only connect common to neg. ( ) leg of control circuits. lk () Common ed () Hot + ht () Y Input, to 0V ht () U Output, to 0V AM-S US

7 AM-PC US Proportional damper actuator, non-spring return, direct coupled, V, for 0 to 0 V phasecut control signal Torque min. 60 in-lb, for control of air dampers. Application For proportional modulation of dampers in HVAC systems. Actual actuator sizing should be done in accordance with the damper manufacturer s specifications. The actuator is mounted directly to a damper shaft up to.0 in diameter by means of its universal clamp. A crankarm and several mounting brackets are available for applications where the actuator cannot be direct coupled to the damper shaft. LISTED 9D TEMP. IND & EG. EQUIP. UL Operation The actuator operates in response to 0 to 0 V phasecut control input from an electronic controller or positioner. A to 0 VDC feedback signal is provided for position indication or master-slave applications. Technical Data Power supply Power consumption Transformer sizing Operating range Y Input impedance Feedback output 'U' Electrical connection Overload protection Torque Direction of rotation Position indication Manual override Angle of rotation unning time un time stability ± % Humidity AM-PC US VAC, ± 0%, 0/60 Hz VDC, ±0% running:. ; holding:. VA (Class power source) 0 to 0 V, phasecut 8kΩ (0 m) to 0 VDC, 0. ma max ft, 8 GA, appliance cable, / conduit connector electronic throughout 0 to 9 rotation min 60 in-lb (8 Nm) reversible with switch C/CC C with a decrease in voltage CC with a decrease in voltage clip on indicator external push button 0 to 9, adjust with mechanical stops 0 secs. constant, independent of load to 9% H, non-condensing Operating temperature - to + F (-0 to +0 C) Storage temperature -0 to +76 F (-0 to +80 C) Housing Housing material NEMA (IP with cable entry down) UL 9-V (flammability rating) Noise level less than d (A) Agency listings UL 87 listed, CSA C. No. certified, CE Quality standard ISO 900 Servicing maintenance free eight.8 lbs. (.kg.) AM-PC US The actuator has a constant running time of 0 seconds. A functional test of the actuator-damper assembly may be done by pressing in the manual override button, this will activate the actuators test mode and cycle the actuator fully closed and back to control point. The microprocessor will correct for compression of tight close-off gaskets with age, providing the actuator is not on its mechanical stops. A to 0 VDC feedback (U) is provided with full 8 volt output range proportional to the operational rotation of the damper. A digital rotation sensing circuit protects the actuator in a stall anywhere in its 9 operating range without the need of limit switches. Add on auxiliary switches are easily fastened directly onto the actuator body for signalling and switching functions. Dimensions [All numbers in brackets are in millimeters.] K- US (supplied) /" Centered (Default) /" Centered (Field Selectable).0" Centered (Field Selectable) K- US (optional) /" to.0" Adjustable K US (optional) /8" to /" Adjustable.0" [76] 8.7" [] 7." [9].8" [6].90" [].77" [].6" [9] D007 G09-IG-Subject to change. elimo Aircontrols (USA), Inc.

8 AM-PC US Proportional damper actuator, non-spring return, direct coupled, V, for 0 to 0 V phasecut control signal Accessories AV Damper shaft extension for AM AV0-8 Universal shaft extension K US Universal clamp for /8 to / shafts K- US Clamp for / to.0 jackshafts K-H Hex shaft clamp, for /8 -/8 shafts KH-AM Crankarm SA US, SA US Auxiliary switches PA US 0 Ω, 00 Ω, 000 Ω, 800 Ω feedback potentiometers PTA-0 Pulse width modulation interface Tool-06 8mm and 0 mm wrench SGA Min. and/or man. positioner in NEMA housing SGF Min. and/or man. positioner for flush panel mounting ZG-0 00Ω resistor for to 0 ma control signal ZA-AM US SM to AM retrofit bracket ZG-AM US Crank arm adaptor kit ZG-00 Mounting bracket ZG-0 Mounting bracket ZG-0 Mounting bracket ZG-0 Mounting bracket ZS-00 eather shield ZS-0 eather shield ZS-60 Explosion-proof housing ZS-00 NEMA X housing AM-PC US - Typical Specification: Control damper actuators shall be electronic direct coupled type which require no crank arm and linkage and be capable of direct mounting to a jackshaft up to a.0 diameter. Actuators shall be UL and CSA listed, have a year warranty, and be manufactured under ISO 900 International Quality Control Standards. The actuator must provide proportional damper control in response to a 0 to 0 V phasecut control input from an electronic controller or positioner. Actuators shall have reversing switch and gear disengagement button on the cover, and be electronically protected from overload at all angles of rotation. Actuators shall respond to to 0VDC output relative to position regardless of the amount of damper rotation. un time shall be constant and independent of torque. A to 0 VDC feedback signal shall be provided for position indication or master-slave applications. Actuators shall be as manufactured by elimo. AM NOTE: hen using AM-PC US actuators, use only the accessories listed on this page. G09-Subject to change. elimo Aircontrols (USA), Inc. iring diagrams VAC Transformer Control Signal ( ) 0 to 0 V Phasecut (+) lk () Common ed () Hot + ht () Y Input, 0 to 0V phasecut ht () U Output, to 0V AM-PC US 8 Provide overload protection and disconnect as required. Actuators may be connected in parallel. Power consumption and input impedance must be observed. Actuator may also be powered by VDC.

9 AM-MFT US Proportional damper actuator, non-spring return, Multi-Function Technology Torque min. 60 in-lb Control to 0 VDC (DEFAULT) Feedback to 0 VDC (DEFAULT) Application For proportional modulation of dampers in HVAC systems. The AM-MFT US is a non-spring return type actuator. hen supply power is removed the actuator will maintain its last position. LISTED 9D TEMP. IND & EG. EQUIP. Technical Data Power supply Power consumption Transformer sizing Electrical connection Overload protection Operating range Y* Input impedance Feedback output U* Torque* AM-MFT US VAC, ± 0%, 0/60 Hz VDC, ±0% running:. ; holding:. VA (Class power source) ft, 8 GA, appliance cable, / conduit connector electronic throughout 0 to 9 rotation to 0 VDC, to 0 ma (w/00 Ω, / resistor) ZG-0 00kΩ for to 0 VDC (0. ma) 00Ω for to 0 ma 00Ω for PM, Floating point and On-Off control to 0 VDC, 0. ma max min 60 in-lb (8 Nm) Direction of rotation* reversible with switch C/CC C=C with decrease in signal CC=CC with a decrease in signal Angle of rotation* 0 to 9, adjust with mechanical stops unning time* 0 seconds constant Angle of otation Off (Default) Adaptation* Override control* Min. (Min Position) = 0% ZS (Mid. Position) = 0% Max. (Max. Position) = 00% Manual override Manual push button Position indication clip on indicator Humidity to 9% H, non-condensing Ambient temperature - to + F (-0 to +0 C) Storage temperature -0 to +76 F (-0 to +80 C) Housing UL Housing material AM-MFT US NEMA, IP (with cable entry down) UL 9-V (flammability rating) Noise level less than d (A) Agency listings UL 87 listed, CE, CSA C. No. certified Quality standard ISO 900 Servicing maintenance free eight.8 lbs. (.kg.) * Variable when configured with MFT options Default/Configuration The default parameters for to 0 VDC applications of the AM-MFT US actuator are assigned during manufacturing. If necessary, custom versions of the actuators can be ordered. The parameters noted in the Technical Data table are variable. These parameters can be changed by three means: Pre-set configurations from elimo Custom configurations from elimo Configurations set by the customer using the MFT-Handy or the MFT-Actuate PC software application. Operation The AM-MFT US actuator provides 9 of rotation and is provided with a position indicator. The actuator will synchronize it s mechanical stop or the damper or valves mechanical stop and use this point for its zero position during normal control operations. The actuator uses a brushless DC motor which is controlled by an Application Specific Integrated Circuit (ASIC) and a microprocessor. The microprocessor provides the intelligence to the ASIC to provide a constant rotation rate and to know the actuator s exact position. The ASIC monitors and controls the brushless DC motor s rotation and provides a Digital otation Sensing (DS) function to prevent damage to the actuator in a stall condition. The position feedback signal is generated with out the need for mechanical feedback potentiometers using DS. The actuator may be stalled anywhere in its normal rotation without the need of mechanical end switches. The AM-MFT US is mounted directly to control shafts up to.0 diameter by means of its universal clamp and anti-rotation bracket. A crankarm and several mounting brackets are available for damper applications where the actuator cannot be direct coupled to the damper shaft. The actuator provides constant torque to the application with and without power applied to the actuator. The AM-MFT US actuator is shipped in a Mid position, compression against seats or gaskets for tight shut-off is accomplished manually. Dimensions [All numbers in brackets are in millimeters.] K- US (supplied) /" Centered (Default) /" Centered (Field Selectable).0" Centered (Field Selectable) K- US (optional) /" to.0" Adjustable K US (optional) /8" to /" Adjustable.0" [76] 8.7" [] 7." [9].8" [6].90" [].77" [].6" [9] D007 G09-IG-Subject to change. elimo Aircontrols (USA), Inc.

10 AM-MFT US Proportional damper actuator, non-spring return, Multi-Function Technology VAC Transformer Control Signal ( ) to 0 VDC (+) to 0 VDC Feedback Signal Standard iring lk () Common ed () + Hot ht () Y Input, to 0V Grn () U Output, to 0V 0 VAC Transformer Control Signal to 0 ma ( ) (+) Standard iring Ω 00Ω / watt to 0 VDC Feedback Signal lk () Common ed () + Hot ht () Y Input, to 0V Grn () U Output, to 0V 0 CC(L) C() CC(L) C() VAC Transformer Control Signal ( ) A to 0 VDC (+) A Open = 0 V Position A Closed = Normal Operation Override to zero position lk () Common ed () + Hot ht () Y Input, to 0V Override to zero position VAC Transformer lk () Common ed () + Hot Ω 00Ω / watt Control Signal ( ) to 0 ma (+) A ht () Y Input, to 0V A Open = ma Position A Closed = Normal Operation AM G09-Subject to change. elimo Aircontrols (USA), Inc. VAC Transformer Control Signal ( ) to 0 VDC (+) C Closed = 0 V Position C Closed = Normal Operation Override to 0 V position Ω Control Signal ( ) -0 VDC or to 0 ma (+) 00Ω / watt C lk () Common ed () + Hot ht () Y Input, to 0V Override control to min, mid, max, positions VAC Transformer A lk () Common ed () + Hot ht () Y Input, to 0V Functions a b c Min* Mid* Max* Normal** 0% 0% 00% Control mode acc. to Y * Default selectable 0-00%. See Configuration Data Sheet. ** Customizable. See Configuration Data Sheet. Override to 0 ma position VAC Transformer lk () Common ed () + Hot Ω Control Signal ( ) to 0 ma (+) ht () Y Input, to 0V 00Ω C / watt Closed = 0 ma Position C Closed = Normal Operation to 0 ma Control Signal Notes ith a -0 ma Input, up to actuators may be wired in parallel. A % shift in the signal is seen when using a 00Ω resistor. Power consumption must be observed. Provide overload protection and disconnect as required. Actuators may be connected in parallel if not mechanically mounted to the same shaft. Power consumption and input impedance must be observed. S S S NC NO SA US Auxiliary Switches for AM-MFT US Actuator may also be powered by VDC. ZG-0 may be used. S S S S S S6 NC NO NC NO SA US 0

11 AM-MFT9 US Proportional damper actuator, non-spring return, V for use with Honeywell electronic Series 90, or a 0 to Ω input Torque min. 60 in-lb Control 0 to Ω Feedback to 0 VDC (DEFAULT) Application For proportional modulation of dampers in HVAC systems. The AM-MFT9 US is a non-spring return type actuator. hen supply power is removed the actuator will maintain its last position. LISTED 9D TEMP. IND & EG. EQUIP. Technical Data Power supply Power consumption Transformer sizing Electrical connection AM-MFT9 US VAC, ± 0%, 0/60 Hz VDC, ±0%. running;. holding VA (Class power source) ft, 8 GA, appliance cable, / conduit connector Overload protection electronic throughout 0 to 9 rotation Operating range 0 to Ω Honeywell electronic series (Not selectable via MFT) 90, or a 0 to Ω input Feedback output U* Torque* Direction of rotation* Angle of rotation* to 0 VDC, 0. ma max min 60 in-lb (8 Nm) reversible with switch C/CC C=C with decrease in signal CC=CC with a decrease in signal 0 to 9, adjust with mechanical stops unning time* 0 seconds constant Angle of otation Off (Default) Adaptation* Override control* Min. (Min Position) = 0% ZS (Mid. Position) = 0% Max. (Max. Position) = 00% Manual override Manual push button Position indication clip on indicator Humidity to 9% H, non-condensing Ambient temperature - to + F (-0 to +0 C) Storage temperature -0 to +76 F (-0 to +80 C) Housing UL Housing material NEMA, IP (with cable entry down) UL 9-V (flammability rating) Noise level less than d (A) Agency listings UL 87 listed, CE, CSA C. No. certified Quality standard ISO 900 Servicing maintenance free eight.8 lbs. (.kg.) * Variable when configured with MFT options AM-MFT9 US Default/Configuration The default parameters for 0 to Ω input applications of the AM-MFT9 US actuator are assigned during manufacturing. If necessary, custom versions of the actuators can be ordered. However the control input cannot be modified via MFT-Handy tool or PC-software. The parameters noted in the Technical Data table are variable. These parameters can be changed by three means: Pre-set configurations from elimo Custom configurations from elimo Configurations set by the customer using the MFT-Handy or the MFT-Actuate PC software application. Operation The AM-MFT9 US actuator provides 9 of rotation and is provided with a position indicator. The actuator will synchronize it s mechanical stop or the damper or valves mechanical stop and use this point for its zero position during normal control operations. The actuator uses a brushless DC motor which is controlled by an Application Specific Integrated Circuit (ASIC) and a microprocessor. The microprocessor provides the intelligence to the ASIC to provide a constant rotation rate and to know the actuator s exact position. The ASIC monitors and controls the brushless DC motor s rotation and provides a Digital otation Sensing (DS) function to prevent damage to the actuator in a stall condition. The position feedback signal is generated with out the need for mechanical feedback potentiometers using DS. The actuator may be stalled anywhere in its normal rotation without the need of mechanical end switches. The AM-MFT9 US is mounted directly to control shafts up to.0 diameter by means of its universal clamp and anti-rotation bracket. A crankarm and several mounting brackets are available for damper applications where the actuator cannot be direct coupled to the damper shaft. The actuator provides constant torque to the application with and without power applied to the actuator. The AM-MFT9 US actuator is shipped in a Mid position, compression against seats or gaskets for tight shut-off is accomplished manually. Dimensions [All numbers in brackets are in millimeters.] K- US (supplied) /" Centered (Default) /" Centered (Field Selectable).0" Centered (Field Selectable) K- US (optional) /" to.0" Adjustable K US (optional) /8" to /" Adjustable.0" [76] 8.7" [] 7." [9].8" [6].90" [].77" [].6" [9] D007 G09-IG-Subject to change. elimo Aircontrols (USA), Inc. 6

12 AM-MFT9 US Proportional damper actuator, non-spring return, V for use with Honeywell electronic Series 90, or a 0 to Ω input Proportional Potentiometric Control G09-Subject to change. elimo Aircontrols (USA), Inc. Switch A Switch Damper Position Damper Open Damper Closed The direction of rotation switch is set so that the fail safe position and the position of the damper is closed with no signal at wire. VAC Transformer Ω Controller Override of AM-MFT9 US A VAC Transformer A Common, lk + Hot, ed, ht, ht, ht 6 U Output -0 VDC AM-MFT9 US Common, lk + Hot, ed, ht, ht, ht 6 U Output -0 VDC AM-MFT9 US Provide overload protection and disconnect as required. Actuators and controller must have separate transformers. Consult controller instruction data for more detailed installation information. To reverse control rotation, use the reversing switch. Series 90 Controller VAC Transformer Series 90 low limit control Ω for 0 to 0% control 80Ω for 0 to 00% control Common, lk + Hot, ed, ht, ht, ht 6 U Output -0 VDC AM-MFT9 US Provide overload protection and disconnect as required. Actuators and controller must have separate transformers. Consult controller instruction data for more detailed installation information. To reverse control rotation, use the reversing switch. AM-MFT9 US used with a Series 90 controller and a Series 90 low limit control Series 90 Controller VAC Transformer Common, lk + Hot, ed, ht, ht, ht 6 U Output -0 VDC Series 90 high limit control - 80Ω AM-MFT9 US Provide overload protection and disconnect as required. Actuators and controller must have separate transformers. Consult controller instruction data for more detailed installation information. To reverse control rotation, use the reversing switch Shunting esistor VAC Transformer Series 90 Controller No. of actuators esistance 0Ω 7.Ω 7.Ω 7.Ω 6 8Ω esistor Kit No. ZG-0 To other actuators Common, lk + Hot, ed, ht, ht, ht 6 U Output -0 VDC AM-MFT9 US Common, lk + Hot, ed, ht, ht, ht 6 U Output -0 VDC Provide overload protection and disconnect as required. Actuators and controller must have separate transformers. Consult controller instruction data for more detailed installation information. esistor value depends on the type of controller and the number of actuators. No resistor is used for one actuator. Honeywell resistor kits may also be used. To reverse control rotation, use the reversing switch. AM-MFT9 US iring multiple actuators to a Series 90 controller. VAC Transformer Series 90 Controller Shunting esistor H0 Changeover Controller Occupied Contact S96A Minimum Position Potentiometer To other actuators Common, lk + Hot, ed, ht, ht, ht 6 U Output -0 VDC AM-MFT9 US Common, lk + Hot, ed, ht, ht, ht 6 U Output -0 VDC AM-MFT9 US Provide overload protection and disconnect as required. Actuators and controller must have separate transformers. Consult controller instruction data for more detailed installation information. esistor value depends on the type of controller and the number of actuators. No resistor is used for one actuator. Honeywell resistor kits may also be used. To reverse control rotation, use the reversing switch. H0 Changeover Controller Shunting esistor VAC Transformer Y 97, 700 Controller No. of actuators esistance 00Ω 90Ω 768Ω esistor Kit No. ZG-06 Shunting esistor VAC Transformer Q09A Minimum Position Potentiometer To other actuators Honeywell Q09A Minimum Position Potentiometer To other actuators Common, lk + Hot, ed, ht, ht, ht 6 U Output -0 VDC AM-MFT9 US Occupied Contact Honeywell T67A Morning armup Common, lk + Hot, ed, ht, ht, ht 6 U Output -0 VDC AM-MFT9 US Used with the 97 and 700 controllers. 97, 700 T77 Honeywell T67A Morning armup Common, lk + Hot, ed, ht, ht, ht 6 U Output -0 VDC Common, lk + Hot, ed, ht, ht, ht 6 U Output -0 VDC AM-MFT9 US AM-MFT9 US Provide overload protection and disconnect as required. Actuators and controller must have separate transformers. Consult controller instruction data for more detailed installation information. esistor value depends on the type of controller and the number of actuators. No resistor is used for one actuator. Honeywell resistor kits may also be used. To reverse control rotation, use the reversing switch. AM AM-MFT9 US used with a Series 90 controller and a Series 90 high limit control iring multiple actuators to a Series 90 controller using a minimum position potentiometer. Typical wiring diagrams for multiple actuators used with the 97, 700 and T77 controllers. 7

13 SM-S US On-off, non-spring return, direct coupled, fast running, V with built-in auxiliary switches iring diagram VAC/VDC ( ) (+) 6 ire No COM + + a 80 0 a open a closed SM-S For end position indication, interlock control, etc., SM-S incorporates built-in auxiliary switches x SPST (A) V UL listed Parallel connection of several actuators is possible: The indication of direction is valid for switch position A Technical Data SM -S Power supply VAC ± 0% 0/60 Hz VDC ± 0% Power consumption AC Stand-by. Full Load 9. Transformer sizing VA Electrical connection ft, 8 GA cable /" conduit connector Angle of rotation mechanically limited to 9 Torque at rated voltage in-lb [ Nm] Direction of rotation reversible with switch A / Position indication and reversible indicator unning time Load Free approx. 6 seconds Full Load approx. 9 seconds Auxiliary switch Open/Closed SPST A, V Humidity to 9% H non-condensing Housing type NEMA type Housing material rating UL 9V-0 (flammability rating) Ambient temperature - F to + F [-0 C to +0 C] Storage temperature -0 F to +76 F [-0 C to +80 C] Noise level d (A) Servicing maintenance free Service life minimum 0,000 operations eight. lbs. [. kg] LISTED 9D TEMP. IND & EG. EQUIP. UL Torque min. in-lb, for control of damper surface up to ft. Application For on-off, fast-acting, control of dampers up to approximately ft [ m ] (based on in-lb per sq. ft.). Actual actuator sizing should be done in accordance with the damper manufacturer s specifications. Control is on-off, two position, from an auxiliary contactor or a manual switch. The direction of rotation is reversible by the use of a switch located on the actuator cover. Operation The actuator is, by means of a special clamp, directly mounted onto the damper shaft. The universal mounting bracket supplied with the actuator will prevent lateral movement of the actuator. The damper actuator is not provided with and does not require any limiting switches, but is protected against overloading. The angle of rotation is mechanically limited to 9. hen reaching the damper or actuator end position, the motor stops automatically. The gears can be manually disengaged by simply pressing down the spring loaded button on the actuator cover. hen the button is pressed down, the damper blades can be adjusted by hand. The position of the actuator is indicated by means of a scale reading For end position indication, interlock control, etc., two built-in, non-adjustable auxiliary switches are provided with the actuator. Accessories ZG-SM Crank arm adaptor kit ZD Angle of rotation limiter ZG-00 Universal mounting bracket ZG-0 Universal mounting bracket ZG-0 Multiple actuator mounting bracket ZG-H Actuator operator handle ZS-00 eather shield, metal ZG-0 eather shield, polycarbonate Dimensions [All numbers in brackets are in millimeters.] / [0] / [7] 7/ [] /8 to / [0 0] /8 to /8 [0 6] /6 [0] 7 / [96] 8 /6 [7] 9/6 [6] D0 G09-IG-Subject to change. elimo Aircontrols (USA), Inc. 8

14 Auxiliary Switches SA US, SA US For the direct coupled actuator AM Operation The SA US and SA US auxiliary switches are used to indicate when a desired position of a damper is reached or to interface additional controls for a specific control sequence. They are modular units that mount directly onto the AM type actuators and held in place with a prefitted screw. A driver disk is attached to the actuator clamp and offers direct transmission of the actuator position to the microswitch operating cams. The switching points can be set over the full scale of 0 to simply by adjusting the slotted discs. iring Diagrams G09-Subject to change. elimo Aircontrols (USA), Inc. Technical Data SA US SA US No. of switches xspdt xspdt Switching capacity 6 A (.A) 0 VAC Switching point adjustable over full actuator rotation 0 to. Pre-setting with scale possible. Electrical connection ft, 8 GA appliance cable / conduit connector Humidity to 9% H non-condensing Ambient temperature - F to + F [-0 C to +0 C] Storage temperature -0 F to +76 F [-0 C to +80 C] Housing type NEMA type Housing material rating UL 9-VA (flammability rating) Agency listings UL 87 listed, CSA C. No. certified, CE eight 8 oz [ g] 9. oz [6 g] Electrical protection auxiliary switches are double insulated S NC N.C. S S NO N.O. SA US N.C. N.O. N.C. N.O. SA US Mounting Instructions. emove pointer assembly from the actuator. Press down the manual override button and rotate the actuator fully counter-clockwise.. Invert SA US switch and turn the driver disk fully clockwise as indicated.. Slide SA US switch onto actuator and check for the correct mating of the driver disk to the universal clamp. Secure with screw.. Adjust switch dials as necessary. emount the white plastic pointer only onto SA US switch. S S S S S S6 Voltage esistive Inductive A.0 A A. A AM 9

15 Feedback Potentiometer PA US For the direct coupled actuator AM Application The PA US feedback potentiometers are used with AM actuators to provide a resistive signal which varies with damper position. The PA US units are applied with commercial proportional temperature controllers to provide feedback of the damper position, or with electric or electronic meters to provide position indication. The signal can also be used as a positioner for parallel operation of multiple actuators. Operation The PA US feedback potentiometer is mounted onto the damper actuator. A driver disk is attached to the actuator clamp and offers direct transmission of the actuator to the potentiometer. iring diagram Mounting Instructions P 0. emove pointer assembly from the actuator. Press down the manual override button and rotate the actuator fully counter-clockwise. P. Invert PA US and turn the driver disk fully clockwise as indicated. P 0 PA. Slide PA US onto actuator and check for the correct mating of the driver disk to the universal clamp. Secure with screw. Types PA00 US Feedback potentiometer 00Ω PA000 US Feedback potentiometer 000Ω PA800 US Feedback potentiometer 800Ω Technical Data esistance values Output PA US as above Tolerance ± % arity ± % esolution min. % esidual resistance Electrical connection Humidity Ambient temperature Storage temperature max. % on both sides ft, 8 GA appliance cable / conduit connector Housing NEMA type Housing rating to 9% H non-condensing - F to + F [-0 C to +0 C] -0 F to +76 F [-0 C to +80 C] UL9-V (flammability rating) Servicing maintenance free Agency listings UL 87 listed, CSA C. No. certified, CE Quality standard ISO 900 eight 8.8 oz [0 g] Electrical protection Class circuits. emount the white plastic pointer only, from the pointer assembly, onto PA US. G09-IG-Subject to change. elimo Aircontrols (USA), Inc. 0

16 AM Series Installation Instructions Quick-Mount Visual Instructions min..88 [8] min /8 / /8 /8 M AM L M /6" - /8" /" [6.] G09-Subject to change. elimo Aircontrols (USA), Inc. ➁ ➀. Turn damper blade to its fully closed position. ith manual override button depressed, rotate actuator clamp to about /6 - /8 between actuator stop and clamp, depending on damper seal design. Slide actuator over shaft and fingertighten nuts.. Using a screwdriver, Select clockwise or counterclockwise rotation. (Example shown is for clockwise closing damper). Slide anti-rotation bracket up under actuator engaging center cut-out on actuator back. Secure bracket with self-tapping screws. 9 Nm ➂. Tighten the two nuts on the universal clamp with 0 mm wrench, 6-8 ft-lb torque. (On dampers with edge seals, actuator will compress damper blades when reaching end position for air-tight damper.). Adjust end stops, if required.

17 Installation Instructions Actuator sizing/preliminary steps Preliminary steps. elimo actuators should be mounted indoors in dry, relatively clean environment free from corrosive fumes. If the actuator is to be mounted outdoors, a protective enclosure must be used to shield the actuator. (See Mechanical Accessories Section). For new construction work, order dampers with extended shafts. Instruct the installing contractor to allow space for mounting and service of the elimo actuator on the shaft.. The AM Series actuator requires a minimum shaft length of.88. Use the AV for short shaft installations on / diameter shafts. AV eplacement or mounting of optional mounting clamp. Squeeze tabs of retaining ring and lift off of actuator.. emove clamp.. eplacement clamp has an alignment mark. Match this mark with the similar mark on the actuator and mount clamp.. Squeeze tabs of retaining ring and fit it into the retaining slot. Note: If retaining ring is not fully seated, the clamp may come loose from the actuator. Alignment points AM actuators which may be used on one shaft: Max Quantity Model Per Shaft AM (-S) US AM-S US AM-MFT US G09-IG-Subject to change. elimo Aircontrols (USA), Inc.

18 Installation Instructions General iring ANING The wiring technician must be trained and experienced with electronic circuits. Disconnect power supply before attempting any wiring connections or changes. Make all connections in accordance with wiring diagrams and follow all applicable local and national codes. Provide disconnect and overload protection as required. Use copper, twisted pair, conductors only. If using electrical conduit, the attachment to the actuator must be made with flexible conduit. Always read the controller manufacturer's installation literature carefully before making any connections. Follow all instructions in this literature. If you have any questions, contact the controller manufacturer and/or elimo. Transformer(s) The AM Series actuators require a VAC class transformer and draw a maximum of VA. The actuator enclosure cannot be opened in the field, there are no parts or components to be replaced or repaired. EMC directive: 89/6/EEC Software class A: Mode of operation type Low voltage directive: 7//EEC Multiple actuators, multiple transformers Multiple actuators positioned by the same control signal may be powered from multiple transformers provided the following rules are followed:. The transformers are properly sized.. All No. wires from all actuators are tied together and tied to the negative leg of the control signal. See wiring diagram. ire length for AM Series actuators Keep power wire runs below the limits listed in the Fig.. If more than one actuator is powered from the same wire run, divide the allowable wire length by the number of actuators to determine the maximum run to any single actuator. Maximum wire length: ire Size Max. Feet. ire Size Max. Feet Ga 800 Ft. 8 Ga 0 Ft. Ga 00 Ft. 0 Ga 7 Ft 6 Ga 700 Ft. Ga Ft Fig. G09-Subject to change. elimo Aircontrols (USA), Inc. CAUTION: It is good practice to power electronic or digital controllers from a separate power transformer than that used for actuators or other end devices. The power supply design in our actuators and other end devices use half wave rectification. Some controllers use full wave rectification. hen these two different types of power supplies are connected to the same power transformer and the DC commons are connected together, a short circuit is created across one of the diodes in the full wave power supply, damaging the controller. Only use a single power transformer to power the controller and actuator if you know the controller power supply uses half wave rectification. Multiple actuators, one transformer Multiple actuators may be powered from one transformer provided the following rules are followed:. The TOTAL current draw of the actuators (VA rating) is less than or equal to the rating of the transformer.. Polarity on the secondary of the transformer is strictly followed. This means that all No. wires from all actuators are connected to the common leg on the transformer and all No wires from all actuators are connected to the hotleg. Mixing wire No. & on one leg of the transformer will result in erratic operation or failure of the actuator and or controls. Operational Information for AM-S US and AM-MFT US Initialization The AM-S US and AM-MFT US must go through an initialization procedure to learn the zero signal position. hen the power is first applied to the actuator, or the gear release button is depressed, the actuator will move to its zero signal position. After the actuator learns this, it will drive to its control position. Example for AM US: actuators, 8 Ga wire 0 Ft Actuators = 0 Ft. Maximum wire run. ire Type and ire Installation Tips For most installations, 8 or 6 Ga. cable works well with the AM type actuators. Use code approved wire nuts, terminal strips or solderless connectors where wires are joined. It is good practice to run control wires unspliced from the actuator to the controller. If splices are unavoidable, make sure the splice can be reached for possible maintenance. Tape and/or wire tie the splice to reduce the possibility of the splice being inadvertently pulled apart. Overload protection All elimo actuators are electronically protected against overload. In the AM series an electronic circuit maintains the current at a level which will not damage the motor while providing adequate holding torque. Motor position detection elimo brushless DC motors eliminate the need for potentiometers for positioning. Inside the motor are three Hall Effect sensors. These sensors detect the spinning rotor and send pulses to the microprocessor which counts the pulses and calculates the position to within / of a revolution of the motor. AM Note: If power is lost to the actuator, and the actuator is moved by use of its manual override, the actuator must be re-initialized when power is returned, by pushing the override button.

19 M Installation Instructions Feature operation Manual Override A button on the actuator cover disengages the gear train so the damper shaft can be moved manually. elease the button and the gear train is re-engaged. Use the manual override to test the installation without power. For tight shut-off the damper should close with of actuator stroke left. Gear release button C CC M Direction of otation Switch AM actuators have a reversing switch on the cover labeled C/CC. Switch position indicates start point. For the AM-S US, with the switch in position C, the actuator rotates clockwise with an decrease in voltage or current. ith the switch in position CC, the actuator rotates counterclockwise with an decrease in voltage or current. During checkout, the switch position can be temporarily reversed and the actuator will reverse its direction. This allows the technician a fast and easy way to check the actuator operation without having to switch wires or change settings on the thermostat. hen the check-out is complete, make sure the switch is placed back to its original position. The AM (-S) US rotates clockwise when the switch is in the C position and power is applied to wire #. hen power is applied to wire # the actuator rotates counter clockwise. otating the C/CC switch to CC reverses the control logic. C CC M 0 VDC VDC M C CC M VDC 0 VDC M AM-S US, AM-SS US Mechanical Angle of otation Limiting The adjustable stops are needed when there is no damper stop or if you want the damper to stop rotating before it reaches its stops. The AM actuator can be indefinitely stalled in any position without harm.. Loosen the two end stops with a No. Phillips head screwdriver being careful not to unscrew the captive nut under the slot.. Move the stops (in. steps) to the desired position and retighten the screws. Control Accuracy and Stability Adjust angle-of-rotation in steps of. AM Series proportional actuators have built-in brushless DC motors which provide better accuracy and longer service life. The AM Series actuators are designed with a unique non-symmetrical deadband. The actuator follows an increasing or decreasing control signal with a 80 mv resolution. If the signal changes in the opposite direction, the actuator will not respond until the control signal changes by 00 mv. This allows these actuators to track even the slightest deviation very accurately, yet allowing the actuator to wait for a much larger change in control signal due to control signal instability. AM Actuator responds to a 80 mv signal when not changing direction from stop position. Satisfied Control Position AM Actuator responds to a 00 mv signal when reversing direction from stop position. Minimum eversed Control Deadband Prior to Normal Control 00 mv G09-IG-Subject to change. elimo Aircontrols (USA), Inc. 80 mv Minimum Control esolution The AM-MFT US control accuracy and stability can be found in the MFT specifications, page 87. Satisfied Control Position

20 L M M L M M Installation Instructions and Accessories Feature operation and additional accessories Adjustable Auxiliary Switches The AM-S US actuator is equipped with two adjustable auxiliary switches used to indicate damper position or to interface additional controls or equipment. Switching positions can be set over the full scale of 0 to 9 simply by setting switch on the actuator cover. Method. Use manual override to position universal clamp to desired switch position.. Turn switch pointer to 0. Method A. Push the manual override button and rotate the clamp to the 0 position.. Set the desired switch position: example: 0% of rotation is. on the setting scale.. Check the switch operation. As the indicator passes the 0 switch position, the contact between S and S, or S and S, is broken and the contact between S and S, or S and S6 is made. Switch ating Voltage esistive load Inductive load VAC A 0. A (switch function may also be monitored by a meter for precise setting) S S S.8 0 S S.6.. S.6.8. S S6. 0 S S S6 0% 0% 00% S Accessories Clamp is in the 0 position AM Mounting brackets ZG-AM - Crank arm adaptor kit ZG-00 ZG-0 ZG-0 ZG-0 Mounting bracket Mounting bracket Mounting bracket Mounting bracket For use when the actuator cannot be mounted directly to the damper shaft. G09-Subject to change. elimo Aircontrols (USA), Inc. AV Short shaft adaptor Used on /8 to /" diameter shafts that are shorter than.87" and mounting space is minimal. AV 0-8 Shaft extension For damper shafts /8 to /6 in [0 to 8] dia or /8 to 9/6 in [0 to ] square. /" min AV Kit specification ball joints KG8 (00) Spacer (7) Crank arm (6) Front mounting bracket (67) ear mounting bracket (06) Screws M6 x 6 (600) 7 Self-tapping screws, x (990) SA US Auxiliary switches, PA US Feedback potentiometers SGA/SGF Dimensions [All numbers in brackets are in millimeters.] 9. 0 [9.8] Minimum and/or manual positioner (electronic), SGA is enclosed in a NEMA housing. The SGF is for flush panel mounting. SGA SGF