G6 C(S)(LCS) 2-way Pressure Compensated Flanged Globe Valve

Transcription

1 G6 C(S)(LCS) -way Pressure Compensated Flanged Globe Valve pplication This valve is typically used in Large ir Handling Units on heating or cooling coils. This valve is suitable for use in a hydronic system with variable fl ow. ronze or stainless steel trim valves can be used for steam applications, depending on actuator and close-off combination. Technical Data G6...C G6...CS G6...LCS Service chilled or hot water, 60% glycol, steam chilled or hot water, 60% glycol, steam chilled or hot water, 60% glycol, steam Flow characteristic modifi ed equal percentage linear ction stem up - open to Sizes ½ to 6 End fi tting 15 lb. fl anged Materials ody Seat Stem Plug Packing iron bronze stainless steel bronze NLP (no lip packing) iron stainless steel stainless steel stainless steel NLP (no lip packing) iron stainless steel stainless steel stainless steel NLP (no lip packing) NSI class NSI 15 Leakage Class III Max inlet Steam 35 psi (41kPa) 100 psi (680kPa) 100 psi (680kPa) Water Media temperature Water Steam 150 psi 50 F 3 F to 300 F (0 C to 149 C) 3 F to 80 F (0 C to 138 C) Maximum ΔP* Water 5 psi (17kPa) Steam 15 psi (103kPa) Rangeability G665C 85:1 G680C 91:1 Valve weights G665C(S)(LCS) G680C(S)(LCS) G6100C(S)(LCS) G615C(S)(LCS) G6150C(S)(LCS) *(50% or more open) G6...C(S)(LCS) -way Flow Patterns 150 psi 50 F 50 psi (340kPa) 50 psi (340kPa) G6100C 98:1 G615C 100:1 Flow arrow shown on rear of valve 57 lbs 75 lbs 17 lbs 149 lbs 197 lbs 3 F to 350 F (0 C to 176 C) 3 F to 338 F (0 C to 170 C) 150 psi 50 F 50 psi (340kPa) 50 psi (340kPa) G6150C 98:1 Stem Up - Open to Valve Nominal Size Type Suitable ctuators C v Inches -way Flanged Non- Spring Return Electronic Spring Fail-Safe 65 ½ G665C(S) 90 3 G680C(S) G6100C(S) 63 5 G615C(S) G6150C(S) 65 ½ G665LCS 90 3 G680LCS G6100LCS 63 5 G615LCS G6150LCS Dimensions EV Series F F *F Series *F Series Valve Nominal Size Valve ody Inches DN [mm] G665C(S) ½ [65] 9 [9] 4.75 [10] G680C(S) 3 [80] 10 [54] 5.37 [137] G6100C(S) 4 [100] 13 [330] 6.87 [175] G615C(S) 5 [15] [400] 7.87 [00] G6150C(S) 6 [150] [451] 8.50 [16] G665LCS ½ [65] 9 [9] 4.75 [10] G680LCS 3 [80] 10 [54] 5.37 [137] G6100LCS 4 [100] 13 [330] 6.87 [175] G615LCS 5 [15] [400] 7.87 [00] G6150LCS 6 [150] [451] 8.50 [16] Piping The valves should be mounted in a weather-protected area in a location that is within the ambient limits of the actuator. llow suffi cient room for valve with actuator and for service. Please allow 1 for complete actuator removal. The G6/G7 preferred mounting position of the valve is with the valve stem vertical above the valve body, for maximum life. However, the assemblies can be mounted with valve stem vertical above the valve or up to 45 degrees in relation to the horizontal pipe. The actuators should never be mounted underneath the valve, as condensation can build up and result in a failure of the actuators. Do not reverse fl ow direction. VK Series D166-WF N /13 - Subject to change. elimo ircontrols (US), Inc US CND LTIN MERIC

2 EV4-3 On/Off, Floating Point, Non-Spring Return, ar, 4 V Technical Data Power supply 4 VC ± 0% 50/60 Hz, 4 VDC ± 10% Power consumption running 6 W Power consumption holding 3.5 W Transformer sizing 7 V (class power source) Electrical connection 3 ft, G plenum rated cable with 1/" conduit connector protected NEM (IP54) Overload protection electronic throughout full stroke Electrical protection actuators are double insulated Control on/off, floating point Operating Range Y on/off, floating point Input impedance 100 k (0.1 m), 500, 1000 (on/off) Feeback Output U No Feedback Stroke " [50 mm] ar Force 56 lbf [500 N] Direction of rotation reversible with switch Position indication stroke indicator on bracket Manual override 5 mm hex crank (3/16" llen), supplied Running time motor 90 seconds (default), variable (90 to 150 seconds) Humidity 5 to 95% RH non condensing mbient temperature - F to +1 F [-30 C to +50 C] Storage temperature -40 F to +176 F [-40 C to +80 C] Housing NEM, IP54, UL enclosure type Housing material luminum die cast and plastic casing gency listings culus acc. to UL /--14, CN/CS E :0, CE acc. to 004/108/EC and 006/95/EC Noise level <65d() Servicing maintenance free Quality standard ISO 9001 Weight 9 lbs Use flexible metal conduit. Push the Listed conduit fitting device over the actuator s cable to butt against the enclosure. Screw in conduit connector. Jacket the actuators input wiring with Listed flexible conduit. Properly terminate the conduit in a suitable junction box. Rated impulse Voltage 800V. Type of action 1. Control Pollution Degree 3. pplication For On/Off and floating control types of globe valves in HVC steam and hydronic systems. ctuator sizing will be dictated by the valve size selection. ll valve selections should be done in accordance with the flow parameters and system specifications. The actuator is mounted directly to the globe valve bonnet by means of its universal clamp and collar. The actuator operates in response to a 4 volt signal being applied from an electronic controller or positioner. Operation The actuator is not provided with and does not require any limit switches, but is electronically protected against overload. The EV series provides 50 mm of downward travel and a visual indicator indicates position of the actuator. When reaching the valve end position, the actuator automatically stops. The gears can be manually disengaged with a button on the actuator cover. The EV series actuators use a sensorless brushless DC motor. The SIC inside monitors and controls the actuator s rotation and provides a digital rotation sensing (DRS) function to prevent damage to the actuator in a stall condition. Power consumption is reduced in holding mode. dd-on auxiliary switches are easily fastened directly onto the actuator body for signaling and switching functions..1 [53] 9. [33] 10. [59] 10.9 [76] 5.5 [140] P /13 - Subject to change. elimo ircontrols (US), Inc US CND LTIN MERIC / CRIEN

3 EV4-3 On/Off, Floating Point, Non-Spring Return, ar, 4 V Typical Specification On/Off, floating control globe valve actuators shall be electronic and direct coupled to the globe valve bonnet via an integrated linkage, which requires no secondary linkage and be capable of mounting to valves.5 to 6 in size. ctuators must provide control in response to a control input from an electronic controller or positioner. ctuators shall have brushless DC motor technology and be protected from overload at all angles of rotation. ctuators shall have reversing switch and manual override on the cover. Run time shall be constant and independent of torque. ctuators shall be culus listed, have a 5-year warranty, and be manufactured under ISO 9001 International Quality Control Standards. ctuators shall be as manufactured by elimo. Wiring Diagrams CUTION Equipment Damage! ctuators may be connected in parallel. Power consumption and input impedance must be observed. 3 ctuators may also be powered by 4 VDC. ctuators with plenum cable do not have numbers; use color codes instead. Meets culus or UL and CS Standard requirements without the need of an electrical ground connection. WRNING Live Electrical Components! During installation, testing, servicing and troubleshooting of this product, it may be necessary to work with live electrical components. Have a qualifi ed licensed electrician or other individual who has been properly trained in handling live electrical components perform these tasks. Failure to follow all electrical safety precautions when exposed to live electrical components could result in death or serious injury. 3 Red () + Wht (3) + P /13 - Subject to change. elimo ircontrols (US), Inc. On/Off Triac Sink (C only) Hot Controller Com lk (1) Common Wht (3) Y 1 Input (C only) Hot Com lk (1) Common Controller Wht (3) Y 1 Input Triac Source US CND LTIN MERIC / CRIEN 74

4 EV4-MFT Proportional, Non-Spring Return, ar, 4 V, Multi-Function Technology Technical Data Power supply 4 VC ± 0% 50/60 Hz, 4 VDC ± 10% Power consumption running 6 W Power consumption holding 3.5 W Transformer sizing 7 V (class power source) Electrical connection 3 ft, G plenum rated cable with 1/" conduit connector protected NEM (IP54) Overload protection electronic throughout full stroke Electrical protection actuators are double insulated Control Proportional/MFT Operating Range Y to 10 VDC, 4 to 0 m (default), variable (VDC, PWM, floating point, on/off) Input impedance 100 k for to 10 VDC (0.1 m), 500 for 4 to 0 m, 1500 for PWM, floating point and On/Off Feeback Output U to 10 VDC, 0.5 m max, VDC variable Stroke " [50 mm] ar Force 56 lbf [500 N] Direction of rotation reversible with switch Position indication stroke indicator on bracket Manual override 5 mm hex crank (3/16" llen), supplied Running time motor 90 seconds (default), variable (90 to 150 seconds) Humidity 5 to 95% RH non condensing mbient temperature - F to +1 F [-30 C to +50 C] Storage temperature -40 F to +176 F [-40 C to +80 C] Housing NEM, IP54, UL enclosure type Housing material luminum die cast and plastic casing gency listings culus acc. to UL /--14, CN/CS E :0, CE acc. to 004/108/EC and 006/95/EC Noise level <65d() Servicing maintenance free Quality standard ISO 9001 Weight 9 lbs Use flexible metal conduit. Push the Listed conduit fitting device over the actuator s cable to butt against the enclosure. Screw in conduit connector. Jacket the actuators input wiring with Listed flexible conduit. Properly terminate the conduit in a suitable junction box. Rated impulse Voltage 800V. Type of action 1. Control Pollution Degree 3. pplication For multiple control types of globe valves in HVC steam and hydronic systems. ctuator sizing will be dictated by the valve size selection. ll valve selections should be done in accordance with the flow parameters and system specifications. The actuator is mounted directly to the globe valve bonnet by means of its universal clamp and collar. The actuator operates in response to many controls types as desired by the customer and/or design control input from an electronic controller or positioner. to 10 VDC feedback signal is provided for position indication. Operation The actuator is not provided with and does not require any limit switches, but is electronically protected against overload. The EV series provides 50 mm of downward travel and a visual indicator indicates position of the actuator. When reaching the valve end position, the actuator automatically stops. The gears can be manually disengaged with a button on the actuator cover. The EV series actuators use a sensorless brushless DC motor. The SIC inside monitors and controls the actuator s rotation and provides a digital rotation sensing (DRS) function to prevent damage to the actuator in a stall condition. Power consumption is reduced in holding mode. dd-on auxiliary switches are easily fastened directly onto the actuator body for signaling and switching functions. -SR and MFT models will have an illuminated green daption/power button to reset and relearn the valve stroke as well as indicate the actuator is powered. This feature allows the actuator to rescale itself based on the actual travel. long with the daption button on MFT models will have a yellow Status light to confirm communication..1 [53] 9. [33] 10. [59] 10.9 [76] 5.5 [140] P /13 - Subject to change. elimo ircontrols (US), Inc US CND LTIN MERIC / CRIEN

5 EV4-MFT Proportional, Non-Spring Return, ar, 4 V, Multi-Function Technology Typical Specification Proportional control globe valve actuators shall be electronic and direct coupled to the globe valve bonnet via an integrated linkage, which requires no secondary linkage and be capable of mounting to valves.5 to 6 in size. ctuators must provide control in response to a control input from an electronic controller or positioner. ctuators shall have brushless DC motor technology and be protected from overload at all angles of rotation. ctuators shall have reversing switch and manual override on the cover. Run time shall be constant and independent of torque. ctuators shall be culus listed, have a 5-year warranty, and be manufactured under ISO 9001 International Quality Control Standards. ctuators shall be as manufactured by elimo. ( ) to 10 VDC Feedback Signal (+) 3 Red () Hot Wht (3) Y Input Org (5) U Output Wiring Diagrams On/Off CUTION Equipment Damage! ctuators may be connected in parallel if not mechanically mounted to the same shaft. Power consumption and input impedance must be observed. 3 ctuators may also be powered by 4 VDC. 7 a 500 resistor converts the 4-0 m control signal to -10 VDC 8 ( ) to 10 VDC 9 (+) Feedback Signal 1 10 lk (1) Common Wht (3) Y1 Input Org (5) U Output to 10V 8 Control signal may be pulsed from either the Hot (Source) or Common (Sink) 4 VC line. Direction of rotation switch P /13 - Subject to change. elimo ircontrols (US), Inc For triac sink the common connection from the actuator must be connected to the hot connection of the controller. Contact closures & also can be triacs. & should both be closed for the triac source and open for triac sink. For triac sink the common connection from the actuator must be connected to the hot connection of the controller. Position feedback cannot be used with a triac sink controller. The actuator internal common reference is not compatible. IN4004 or IN4007 diode. (IN4007 supplied, elimo part number 40155) ctuators with plenum cable do not have numbers; use color codes instead. Meets culus or UL and CS Standard requirements without the need of an electrical ground connection. WRNING Live Electrical Components! During installation, testing, servicing and troubleshooting of this product, it may be necessary to work with live electrical components. Have a qualifi ed licensed electrician or other individual who has been properly trained in handling live electrical components perform these tasks. Failure to follow all electrical safety precautions when exposed to live electrical components could result in death or serious injury. VDC/4-0 m ( ) Control Signal (+) VDC/m ( ) Control Signal (+) VDC/m Ω Ω Ω 1/4 watt 500 Ω 1/4 watt (C Only) 7 C 3 Wht (3) Y 1 Input, to 10V Org (5) U Output, to 10V Wht (3) Y 1 Input, to 10V Org (5) Min* Functions 0% a b c Mid* Max* Normal** 50% 100% Control mode acc. to Y * Default selectable 0-100%. See Configuration Data Sheet. ** Customizable. See Configuration Data Sheet. Override US CND LTIN MERIC / CRIEN 80

6 EVX4-3 On/Off, Floating Point, Non-Spring Return, ar, 4 V Technical Data Power supply 4 VC ± 0% 50/60 Hz, 4 VDC ± 10% Power consumption running 6 W Power consumption holding 3.5 W Transformer sizing 7 V (class power source) Electrical connection 3 ft, G plenum rated cable with 1/" conduit connector protected NEM (IP54) Overload protection electronic throughout full stroke Electrical protection actuators are double insulated Control on/off, floating point Operating Range Y on/off, floating point Input impedance 100 k (0.1 m), 500, 1000 (on/off) Feeback Output U No Feedback Stroke " [50 mm] ar Force 56 lbf [500 N] Direction of rotation reversible with switch Position indication stroke indicator on bracket Manual override 5 mm hex crank (3/16" llen), supplied Running time motor 90 seconds (default), variable (90 to 150 seconds) Humidity 5 to 95% RH non condensing mbient temperature - F to +1 F [-30 C to +50 C] Storage temperature -40 F to +176 F [-40 C to +80 C] Housing NEM, IP54, UL enclosure type Housing material luminum die cast and plastic casing gency listings culus acc. to UL /--14, CN/CS E :0, CE acc. to 004/108/EC and 006/95/EC Noise level <65d() Servicing maintenance free Quality standard ISO 9001 Weight 9 lbs Use flexible metal conduit. Push the Listed conduit fitting device over the actuator s cable to butt against the enclosure. Screw in conduit connector. Jacket the actuators input wiring with Listed flexible conduit. Properly terminate the conduit in a suitable junction box. Rated impulse Voltage 800V. Type of action 1. Control Pollution Degree 3. pplication For On/Off and floating control types of globe valves in HVC steam and hydronic systems. ctuator sizing will be dictated by the valve size selection. ll valve selections should be done in accordance with the flow parameters and system specifications. The actuator is mounted directly to the globe valve bonnet by means of its universal clamp and collar. The actuator operates in response to a 4 volt signal being applied from an electronic controller or positioner. Operation The actuator is not provided with and does not require any limit switches, but is electronically protected against overload. The EV series provides 50 mm of downward travel and a visual indicator indicates position of the actuator. When reaching the valve end position, the actuator automatically stops. The gears can be manually disengaged with a button on the actuator cover. The EV series actuators use a sensorless brushless DC motor. The SIC inside monitors and controls the actuator s rotation and provides a digital rotation sensing (DRS) function to prevent damage to the actuator in a stall condition. Power consumption is reduced in holding mode. dd-on auxiliary switches are easily fastened directly onto the actuator body for signaling and switching functions..1 [53] 9. [33] 10. [59] 10.9 [76] 5.5 [140] P /13 - Subject to change. elimo ircontrols (US), Inc US CND LTIN MERIC / CRIEN

7 EVX4-3 On/Off, Floating Point, Non-Spring Return, ar, 4 V Typical Specification On/Off, floating control globe valve actuators shall be electronic and direct coupled to the globe valve bonnet via an integrated linkage, which requires no secondary linkage and be capable of mounting to valves.5 to 6 in size. ctuators must provide control in response to a control input from an electronic controller or positioner. ctuators shall have brushless DC motor technology and be protected from overload at all angles of rotation. ctuators shall have reversing switch and manual override on the cover. Run time shall be constant and independent of torque. ctuators shall be culus listed, have a 5-year warranty, and be manufactured under ISO 9001 International Quality Control Standards. ctuators shall be as manufactured by elimo. Wiring Diagrams CUTION Equipment Damage! ctuators may be connected in parallel. Power consumption and input impedance must be observed. 3 ctuators may also be powered by 4 VDC. ctuators with plenum cable do not have numbers; use color codes instead. Meets culus or UL and CS Standard requirements without the need of an electrical ground connection. WRNING Live Electrical Components! During installation, testing, servicing and troubleshooting of this product, it may be necessary to work with live electrical components. Have a qualifi ed licensed electrician or other individual who has been properly trained in handling live electrical components perform these tasks. Failure to follow all electrical safety precautions when exposed to live electrical components could result in death or serious injury. 3 Red () + Wht (3) + P /13 - Subject to change. elimo ircontrols (US), Inc. On/Off Triac Sink (C only) Hot Controller Com lk (1) Common Wht (3) Y 1 Input (C only) Hot Com lk (1) Common Controller Wht (3) Y 1 Input Triac Source US CND LTIN MERIC / CRIEN 76

8 EVX10-3 On/Off, Floating Point, Non-Spring Return, ar, 100 to 40 VC Technical Data Power supply VC ± 0%, 50/60 Hz Power consumption running 5 W Power consumption holding 1 W Transformer sizing 10 V (class power source) Electrical connection 3 ft, G appliance rated cable with 1/" conduit connector protected NEM (IP54) Overload protection electronic throughout full stroke Electrical protection actuators are double insulated Control on/off, floating point Operating Range Y on/off, floating point Input impedance 100 k (0.1 m), 500, 1000 (on/off) Feeback Output U No Feedback Stroke " [50 mm] ar Force 56 lbf [500 N] Direction of rotation reversible with switch Position indication stroke indicator on bracket Manual override 5 mm hex crank (3/16" llen), supplied Running time motor 90 seconds (default), variable (90 to 150 seconds) Humidity 5 to 95% RH non condensing mbient temperature - F to +1 F [-30 C to +50 C] Storage temperature -40 F to +176 F [-40 C to +80 C] Housing NEM, IP54, UL enclosure type Housing material luminum die cast and plastic casing gency listings culus acc. to UL /--14, CN/CS E :0, CE acc. to 004/108/EC and 006/95/EC Noise level <65d() Servicing maintenance free Quality standard ISO 9001 Weight 9 lbs Use flexible metal conduit. Push the Listed conduit fitting device over the actuator s cable to butt against the enclosure. Screw in conduit connector. Jacket the actuators input wiring with Listed flexible conduit. Properly terminate the conduit in a suitable junction box. Rated impulse Voltage.5 KV. Type of action 1. Control Pollution Degree 3. pplication For On/Off and floating control types of globe valves in HVC steam and hydronic systems. ctuator sizing will be dictated by the valve size selection. ll valve selections should be done in accordance with the flow parameters and system specifications. The actuator is mounted directly to the globe valve bonnet by means of its universal clamp and collar. The actuator operates in response to a 10 volt signal being applied from an electronic controller or positioner. Operation The actuator is not provided with and does not require any limit switches, but is electronically protected against overload. The EV series provides 50 mm of downward travel and a visual indicator indicates position of the actuator. When reaching the valve end position, the actuator automatically stops. The gears can be manually disengaged with a button on the actuator cover. The EV series actuators use a sensorless brushless DC motor. The SIC inside monitors and controls the actuator s rotation and provides a digital rotation sensing (DRS) function to prevent damage to the actuator in a stall condition. Power consumption is reduced in holding mode. dd-on auxiliary switches are easily fastened directly onto the actuator body for signaling and switching functions..1 [53] 9. [33] 10. [59] 10.9 [76] 5.5 [140] P /13 - Subject to change. elimo ircontrols (US), Inc US CND LTIN MERIC / CRIEN

9 EVX10-3 On/Off, Floating Point, Non-Spring Return, ar, 100 to 40 VC Typical Specification Wiring Diagrams On/Off, floating control globe valve actuators shall be electronic and direct coupled to the globe valve bonnet via an integrated linkage, which requires no secondary linkage and be capable of mounting to valves.5 to 6 in size. ctuators must provide control in response to a control input from an electronic controller or positioner. ctuators shall have brushless DC motor technology and be protected from overload at all angles of rotation. ctuators shall have reversing switch and manual override on the cover. Run time shall be constant and independent of torque. ctuators shall be culus listed, have a 5-year warranty, and be manufactured under ISO 9001 International Quality Control Standards. ctuators shall be as manufactured by elimo. ctuators with appliance cables are numbered. CUTION Equipment Damage! ctuators may be connected in parallel. Power consumption and input impedance must be observed. Meets culus or UL and CS Standard requirements without the need of an electrical ground connection. WRNING Live Electrical Components! During installation, testing, servicing and troubleshooting of this product, it may be necessary to work with live electrical components. Have a qualifi ed licensed electrician or other individual who has been properly trained in handling live electrical components perform these tasks. Failure to follow all electrical safety precautions when exposed to live electrical components could result in death or serious injury. N L1 100 to 40 VC lu (1) Common Hot H L rn () + Wht (3) + On/Off P /13 - Subject to change. elimo ircontrols (US), Inc. 100 to 40 VC N L1 Hot H L Floating Point lu (1) Common rn () + Wht (3) US CND LTIN MERIC / CRIEN 78

10 EVX4-MFT Proportional, Non-Spring Return, ar, 4 V, Multi-Function Technology Technical Data Power supply 4 VC ± 0% 50/60 Hz, 4 VDC ± 10% Power consumption running 6 W Power consumption holding 3.5 W Transformer sizing 7 V (class power source) Electrical connection 3 ft, G plenum rated cable with 1/" conduit connector protected NEM (IP54) Overload protection electronic throughout full stroke Electrical protection actuators are double insulated Control Proportional/MFT Operating Range Y to 10 VDC, 4 to 0 m (default), variable (VDC, PWM, floating point, on/off) Input impedance 100 k for to 10 VDC (0.1 m), 500 for 4 to 0 m, 1500 for PWM, floating point and On/Off Feeback Output U to 10 VDC, 0.5 m max, VDC variable Stroke " [50 mm] ar Force 56 lbf [500 N] Direction of rotation reversible with switch Position indication stroke indicator on bracket Manual override 5 mm hex crank (3/16" llen), supplied Running time motor 90 seconds (default), variable (90 to 150 seconds) Humidity 5 to 95% RH non condensing mbient temperature - F to +1 F [-30 C to +50 C] Storage temperature -40 F to +176 F [-40 C to +80 C] Housing NEM, IP54, UL enclosure type Housing material luminum die cast and plastic casing gency listings culus acc. to UL /--14, CN/CS E :0, CE acc. to 004/108/EC and 006/95/EC Noise level <65d() Servicing maintenance free Quality standard ISO 9001 Weight 9 lbs Use flexible metal conduit. Push the Listed conduit fitting device over the actuator s cable to butt against the enclosure. Screw in conduit connector. Jacket the actuators input wiring with Listed flexible conduit. Properly terminate the conduit in a suitable junction box. Rated impulse Voltage 800V. Type of action 1. Control Pollution Degree 3. pplication For multiple control types of globe valves in HVC steam and hydronic systems. ctuator sizing will be dictated by the valve size selection. ll valve selections should be done in accordance with the flow parameters and system specifications. The actuator is mounted directly to the globe valve bonnet by means of its universal clamp and collar. The actuator operates in response to many controls types as desired by the customer and/or design control input from an electronic controller or positioner. to 10 VDC feedback signal is provided for position indication. Operation The actuator is not provided with and does not require any limit switches, but is electronically protected against overload. The EV series provides 50 mm of downward travel and a visual indicator indicates position of the actuator. When reaching the valve end position, the actuator automatically stops. The gears can be manually disengaged with a button on the actuator cover. The EV series actuators use a sensorless brushless DC motor. The SIC inside monitors and controls the actuator s rotation and provides a digital rotation sensing (DRS) function to prevent damage to the actuator in a stall condition. Power consumption is reduced in holding mode. dd-on auxiliary switches are easily fastened directly onto the actuator body for signaling and switching functions. -SR and MFT models will have an illuminated green daption/power button to reset and relearn the valve stroke as well as indicate the actuator is powered. This feature allows the actuator to rescale itself based on the actual travel. long with the daption button on MFT models will have a yellow Status light to confirm communication..1 [53] 9. [33] 10. [59] 10.9 [76] 5.5 [140] P /13 - Subject to change. elimo ircontrols (US), Inc US CND LTIN MERIC / CRIEN

11 EVX4-MFT Proportional, Non-Spring Return, ar, 4 V, Multi-Function Technology Typical Specification Proportional control globe valve actuators shall be electronic and direct coupled to the globe valve bonnet via an integrated linkage, which requires no secondary linkage and be capable of mounting to valves.5 to 6 in size. ctuators must provide control in response to a control input from an electronic controller or positioner. ctuators shall have brushless DC motor technology and be protected from overload at all angles of rotation. ctuators shall have reversing switch and manual override on the cover. Run time shall be constant and independent of torque. ctuators shall be culus listed, have a 5-year warranty, and be manufactured under ISO 9001 International Quality Control Standards. ctuators shall be as manufactured by elimo. ( ) to 10 VDC Feedback Signal (+) 3 Red () Hot Wht (3) Y Input Org (5) U Output Wiring Diagrams On/Off CUTION Equipment Damage! ctuators may be connected in parallel if not mechanically mounted to the same shaft. Power consumption and input impedance must be observed. 3 ctuators may also be powered by 4 VDC. 7 a 500 resistor converts the 4-0 m control signal to -10 VDC 8 ( ) to 10 VDC 9 (+) Feedback Signal 1 10 lk (1) Common Wht (3) Y1 Input Org (5) U Output to 10V 8 Control signal may be pulsed from either the Hot (Source) or Common (Sink) 4 VC line. Direction of rotation switch P /13 - Subject to change. elimo ircontrols (US), Inc For triac sink the common connection from the actuator must be connected to the hot connection of the controller. Contact closures & also can be triacs. & should both be closed for the triac source and open for triac sink. For triac sink the common connection from the actuator must be connected to the hot connection of the controller. Position feedback cannot be used with a triac sink controller. The actuator internal common reference is not compatible. IN4004 or IN4007 diode. (IN4007 supplied, elimo part number 40155) ctuators with plenum cable do not have numbers; use color codes instead. Meets culus or UL and CS Standard requirements without the need of an electrical ground connection. WRNING Live Electrical Components! During installation, testing, servicing and troubleshooting of this product, it may be necessary to work with live electrical components. Have a qualifi ed licensed electrician or other individual who has been properly trained in handling live electrical components perform these tasks. Failure to follow all electrical safety precautions when exposed to live electrical components could result in death or serious injury. VDC/4-0 m ( ) Control Signal (+) VDC/m ( ) Control Signal (+) VDC/m Ω Ω Ω 1/4 watt 500 Ω 1/4 watt (C Only) 7 C 3 Wht (3) Y 1 Input, to 10V Org (5) U Output, to 10V Wht (3) Y 1 Input, to 10V Org (5) Min* Functions 0% a b c Mid* Max* Normal** 50% 100% Control mode acc. to Y * Default selectable 0-100%. See Configuration Data Sheet. ** Customizable. See Configuration Data Sheet. Override US CND LTIN MERIC / CRIEN 8

12 FUP-X1, FUP-S-X1 ctuators, On/Off Dimensions with G...(S) Series -Way Valve D0 C N /13 - Subject to change. elimo ircontrols (US), Inc. Models FUP-X1 FUP-S-X1 w/built-in ux. Switch Technical Data Power supply VC -0% / +10%, 50/60 Hz VDC ±10% Power consumption running 7 W holding 3.5 W Transformer sizing 7 4 VC (Class power source) VC 40 VC Electrical connection 3 ft, G appliance cable, ½" conduit connector -S models: two 3 ft, gauge appliance cables with ½ conduit connectors Overload protection electronic throughout 0 to 95 rotation Control on/off Torque 0 in-lb [10 Nm] minimum Direction of rotation spring reversible with CW/CCW mounting Mechanical angle of rotation 95 (adjustable with mechanical end stop, 35 to 95 ) Running time motor <75 sec spring 0 -4 F to 1 F [-0 C to 50 C]; <60 - F [-30 C] Position indication visual indicator, 0 to 95 (0 is full spring return position) Manual override 5 mm hex crank (³ ₁₆" llen), supplied Humidity max. 95% RH non-condensing mbient temperature - F to 1 F [-30 C to 50 C] Housing Nema, IP54, Enclosure Type Housing material Zinc coated metal and plastic casing gency listings culus acc. to UL /--14, CN/CS E :0, CE acc. to 004/108/EC & 006/95/EC Noise level <50d() 75 seconds 6d() spring return Quality standard ISO 9001 Weight 4.6 lbs (.1 kg), 4.9 lbs (.5 kg) with switches Rated Impulse Voltage 4kV, Type of action 1. (1.. for -S version), Control Pollution Degree 3. FUP-S-X1 uxiliary switches x SPDT 3 50 VC, UL approved one set at +10, one adjustable 10 to 90 Valve Nominal Size Valve ody Inches DN [mm] C G(S) [117] 1.1 [9] 8.1 [06] G(S) 1¼ " [117] 1.37 [35] 8.37 [13] Dimensions with G3...(D) Series 3-Way Valve C Valve Nominal Size Valve ody Inches DN [mm] C G3(D) [117] 1.56 [40] 8.56 [17] G3(D) 1¼ [117] 1.6 [41] 8.6 [19] D US CND LTIN MERIC 73

13 FUP-X1, FUP-S-X1 ctuators, On/Off Dimensions with G6/G6C NSI 15 and G6/G6C NSI 50 Series -Way Valve Dimensions with G7 and G7D NSI 15/50 Series 3-Way Valve G G D167_GM_NG D167_GM_NG_3 Valve Nominal Size Valve ody Inches DN [mm] C G6 NSI 15 ½ [9] 4.75 [11] [343] G6 NSI 15 3" [54] 5.37 [136] [354] G6 NSI 50 ½ [44] 4.75 [11] [356] G6 NSI 50 3" [73] 5.37 [136] 14.1 [359] G6C NSI 15 ½ [0] 4.75 [11] [343] G6C NSI [54] 5.37 [136] [354] G6C NSI 50 ½ [44] 4.75 [11] [343] G6C NSI [54] 5.37 [136] [354] Valve Nominal Size Valve ody Inches DN [mm] C G7 & G7D NSI 15 ½ [9] 7.1 [1] [35] G7 & G7D NSI [54] 8.00 [03] [367] G7D NSI [330] 9.87 [51] 15.5 [387] G7 & G7D NSI 50 ½ [44] 7.37 [7] [356] G7 & G7D NSI [73] 8.37 [13] 14.6 [371] G7D NSI [346] 10.5 [60] 15.5 [387] Valve Nominal Size Valve ody Inches DN [mm] C-x G6 NSI 15 ½ " [9] 4.75" [11].5" [464] G6 NSI " [54] 5.37" [136] 19." [487] G6 NSI 50 ½ " [44] 4.75" [11].5" [464] G6 NSI 50 3" " [73] 5.37" [136] 19." [487] G6C NSI 15 4" " [330] 6.87" [175] 0.5 [514] G6C NSI 15 5" " [400] 7.87" [00] 0.87 [530] G6C NSI 15 6" " [451] 8.50" [16] 1.50 [546] G6C NSI 50 4" " [346] 6.87" [175] 0.5" [514] G6C NSI 50 5" " [4] 7.87" [00] 0.87 [530] G6C NSI 50 6" 150.6" [473] 8.50 [16] 1.50 [546] Valve Nominal Size Valve ody Inches DN [mm] C-x G7 NSI 15 ½ [9] 7.1 [1].5 [464] G7 NSI [54] 8.00 [03] 19. [487] G7 NSI [330.] 9.87 [51] 0.00 [508] G7D NSI [305] [67].37 [467] G7D NSI [359] 11.1 [8] 19. [487] G7 NSI 50 ½ [44] 7.37 [7].75 [476] G7 NSI [73] 8.37 [13] [49] G7 NSI [346] 10.5 [60] 0.37 [517] G7D NSI [37] [79] 0.56 [5] G7D NSI [368] [9] 1.5 [540] N /13 - Subject to change. elimo ircontrols (US), Inc US CND LTIN MERIC

14 FUP-X1, FUP-S-X1 ctuators, On/Off Wiring Diagrams 1 Provide overload protection and disconnect as required. CUTION Equipment Damage! ctuators may be connected in parallel. Power consumption and input impedance must be observed. 3 No ground connection is required. 4 For end position indication, interlock control, fan startup, etc., FUP-S-X1 incorporates two built-in auxiliary switches: x SPDT, 3 VC, UL pproved, one switch is fixed at +10, one is adjustable 10 to 90. NFUP-X1 NFUP-S-X1 W066_NF(X)UP On/Off wiring for FUP-X1 Meets culus requirements without the need of an electrical ground connection. WRNING Live Electrical Components! During installation, testing, servicing and troubleshooting of this product, it may be necessary to work with live electrical components. Have a qualifi ed licensed electrician or other individual who has been properly trained in handling live electrical components perform these tasks. Failure to follow all electrical safety precautions when exposed to live electrical components could result in death or serious injury. W067_NF(X)UP-S NFUP-S-X1 N /13 - Subject to change. elimo ircontrols (US), Inc. uxiliary Switches for FUP-S-X US CND LTIN MERIC 75

15 FX4-MFT-X1 ctuators, Multi-Function Technology Dimensions with G...(S) Series -Way Valve D0 C Models FX4-MFT-X1 FX4-MFT-S-X1 w/built-in ux. Switch Technical Data Power supply 4 VC, +/- 0%, 50/60 Hz 4 VDC, +0% / -10% Power running 7.5 W consumption holding 3 W Transformer sizing 10 V (Class power source) Electrical connection 3 ft [1m], 10 ft [3m] or 16 ft [5m] G appliance or plenum cables, with or without ½ conduit connector -S models: two 3 ft [1m], 10 ft [3m] or 16 ft [5m] appliance cables with or without ½ conduit connectors Overload protection electronic throughout 0 to 95 rotation Operating range Y* to 10 VDC, 4 to 0 m (default) variable (VDC, PWM, floating point, on/off) Input impedance 100 kω for to 10 VDC (0.1 m) 500 Ω for 4 to 0 m 1500 Ω for PWM, floating point and on/off control Feedback output U* to 10 VDC, 0.5 m max Torque minimum 0 in-lb (0 Nm) Direction of spring reversible with cw/ccw mounting rotation* motor reversible with built-in switch Mechanical 95 (adjustable with mechanical end stop, 35 to 95 ) angle of rotation* Running time spring <0 -4 F to 1 F [-0 C to 50 C]; <60 - F [-30 C] motor* 150 seconds (default), variable (70 to 0 seconds) ngle of rotation off (default) adaptation Override control* min position = 0% mid. position = 50% max. position = 100% Position indication visual indicator, 0 to 95 (0 is spring return position) Manual override 5 mm hex crank (³ ₁₆ llen), supplied Humidity max. 95% RH, non-condensing mbient temperature - to 1 F (-30 to 50 C) Housing NEM, IP54, Enclosure Type Housing material zinc coated metal and plastic casing Noise level 40d() 150 seconds, run time dependent 6d() spring return gency listings culus acc. to UL /--14, CN/CS E :0, CE acc. to 004/108/EC & 006/95/EC Quality standard ISO 9001 Weight 4. lbs. (1.9 kg), 4.3 lbs. ( kg) with switch * Variable when configured with MFT options Rated Impulse Voltage 800V, Type of action 1. (1.. for -S version), Control Pollution Degree 3. Programmed for 70 sec motor run time. t 150 sec motor run time, transformer sizing is 8.5 V and power consumption is 6 W running / 3 W holding. FX4-MFT-S-X1 uxiliary switches x SPDT 3 50 VC, UL approved one set at +10, one adjustable 10 to 90 Valve Nominal Size Valve ody Inches DN [mm] C G(S) 1½ [137] 1.50 [38] 8.50 [16] G(S) " [156] 1.56 [40] 8.56 [17] Dimensions with G3...(D) Series 3-Way Valve C Valve Nominal Size Valve ody Inches DN [mm] C G3(D) 1½ [137] 1.6 [41] 8.6 [19] G3(D) [156] 1.87 [48] 8.87 [5] D5 N /13 - Subject to change. elimo ircontrols (US), Inc US CND LTIN MERIC

16 FX4-MFT-X1 ctuators, Multi-Function Technology Dimensions with G6/G6C NSI 15 and G6/G6C NSI 50 Series -Way Valve Dimensions with G7 and G7D NSI 15/50 Series 3-Way Valve D167_GM_NG D167_GM_NG_3 Valve Nominal Size Valve ody Inches DN [mm] C G6 NSI 15 ½ [9] 4.75 [11] [343] G6 NSI 15 3" [54] 5.37 [136] [354] G6 NSI 50 ½ [44] 4.75 [11] [356] G6 NSI 50 3" [73] 5.37 [136] 14.1 [359] G6C NSI 15 ½ [0] 4.75 [11] [343] G6C NSI [54] 5.37 [136] [354] G6C NSI 50 ½ [44] 4.75 [11] [343] G6C NSI [54] 5.37 [136] [354] Valve Nominal Size Valve ody Inches DN [mm] C G7 & G7D NSI 15 ½ [9] 7.1 [1] [35] G7 & G7D NSI [54] 8.00 [03] [367] G7D NSI [330] 9.87 [51] 15.5 [387] G7 & G7D NSI 50 ½ [44] 7.37 [7] [356] G7 & G7D NSI [73] 8.37 [13] 14.6 [371] G7D NSI [346] 10.5 [60] 15.5 [387] N /13 - Subject to change. elimo ircontrols (US), Inc. Valve Nominal Size Valve ody Inches DN [mm] C-x G6 NSI 15 ½ " [9] 4.75" [11].5" [464] G6 NSI " [54] 5.37" [136] 19." [487] G6 NSI 50 ½ " [44] 4.75" [11].5" [464] G6 NSI 50 3" " [73] 5.37" [136] 19." [487] G6C NSI 15 4" " [330] 6.87" [175] 0.5 [514] G6C NSI 15 5" " [400] 7.87" [00] 0.87 [530] G6C NSI 15 6" " [451] 8.50" [16] 1.50 [546] G6C NSI 50 4" " [346] 6.87" [175] 0.5" [514] G6C NSI 50 5" " [4] 7.87" [00] 0.87 [530] G6C NSI 50 6" 150.6" [473] 8.50 [16] 1.50 [546] Valve Nominal Size Valve ody Inches DN [mm] C-x G7 NSI 15 ½ [9] 7.1 [1].5 [464] G7 NSI [54] 8.00 [03] 19. [487] G7 NSI [330.] 9.87 [51] 0.00 [508] G7D NSI [305] [67].37 [467] G7D NSI [359] 11.1 [8] 19. [487] G7 NSI 50 ½ [44] 7.37 [7].75 [476] G7 NSI [73] 8.37 [13] [49] G7 NSI [346] 10.5 [60] 0.37 [517] G7D NSI [37] [79] 0.56 [5] G7D NSI [368] [9] 1.5 [540] US CND LTIN MERIC 77

17 FX4-MFT-X1 ctuators, Multi-Function Technology Wiring Diagrams 1 Provide overload protection and disconnect as required. CUTION Equipment Damage! ctuators may be connected in parallel if not mechanically mounted to the same shaft. Power consumption and input impedance must be observed. W600_F_FX 3 ctuators may also be powered by 4 VDC Position feedback cannot be used with Triac sink controller. The actuator internal common reference is not compatible. Control signal may be pulsed from either the Hot (source) or the Common (sink) 4 VC line. Contact closures & also can be triacs. & should both be closed for triac source and open for triac sink. For triac sink the common connection from the actuator must be connected to the hot connection of the controller. uxiliary Switches for FX4-MFT-S-X1 FX4-MFT-S-X1 W399_08 Meets UL requirements without the need of an electrical ground connection. The ZG-R Ω resistor may be used. WRNING Live Electrical Components! During installation, testing, servicing and troubleshooting of this product, it may be necessary to work with live electrical components. Have a qualifi ed licensed electrician or other individual who has been properly trained in handling live electrical components perform these tasks. Failure to follow all electrical safety precautions when exposed to live electrical components could result in death or serious injury. VDC/4-0 m W399_08 PWM On/Off control W399_08 W399_08 N /13 - Subject to change. elimo ircontrols (US), Inc. Floating Point control US CND LTIN MERIC

18 FX4-MFT-X1 ctuators, Multi-Function Technology Wiring Diagrams for Multiple MFT ctuators 3 ctuators may also be powered by 4 VDC 5 ctuators with plenum rated cable do not have numbers on wires; use color codes instead. ctuators with appliance cable are numbered. WRNING Live Electrical Components! During installation, testing, servicing and troubleshooting of this product, it may be necessary to work with live electrical components. Have a qualifi ed licensed electrician or other individual who has been properly trained in handling live electrical components perform these tasks. Failure to follow all electrical safety precautions when exposed to live electrical components could result in death or serious injury. 3 Control Signal to 10 VDC or 4 to 0 m ( ) (+) 500 Ω 1/4 watt Master 5 Wht (3) Y Input, to 10 V Org (5) U Output to 10 V CCW CW Slave 5 W34 FX4_MFT_X1 Wiring multiple...mft actuators to a single shaft and/or on valves. ll MFT actuators are wired in master-slave confi guration. MFT actuator confi gurations should also coordinate with each other. Meaning the master input = controllers output. Master output = slave output. Slave output = controller input. Maximum 4 actuators per shaft. Wht (3) Y Input, to 10 V Org (5) U CCW CW Example Controller Output Master Feedback Slave Input Slave Feedback to 10 VDC to 10 VDC to 10 VDC 0 to 5 VDC VDC/4-0 m N /13 - Subject to change. elimo ircontrols (US), Inc US CND LTIN MERIC 79

19 FX4-MFT95-X1 ctuators, Ω Dimensions with G...(S) Series -Way Valve D0 C Models FX4-MFT95-X1 Technical Data Power supply 4 VC, +/- 0%, 50/60 Hz 4 VDC, +0% / -10% Power running 7.5 W consumption holding 3 W Transformer sizing 10 V (Class power source) Electrical connection 3 ft [1m], G plenum cable, with or without ½ conduit connector Overload protection electronic throughout 0 to 95 rotation Operating range Y 0 to 135 Ω Honeywell Electronic Series 90, 0 to 135 Ω input Feedback output U* to 10 VDC, 0.5 m max Torque minimum 0 in-lb (0 Nm) Direction spring reversible with CW/CCW mounting of rotation* motor reversible with built-in switch Mechanical 95 (adjustable with mechanical end stop, 35 to 95 ) angle of rotation* Running time spring <0 -4 F to 1 F [-0 C to 50 C]; <60 - F [-30 C] motor* 150 seconds (default), variable (70 to 0 seconds) ngle of rotation off (default) adaptation Position indication visual indicator, 0 to 95 (0 is spring return position) Manual override 5 mm hex crank (³ ₁₆ llen), supplied Humidity max. 95% RH, non-condensing mbient temperature - to 1 F (-30 to 50 C) Housing NEM, IP54, Enclosure Type Housing material zinc coated metal and plastic casing Noise level 40d() 150 seconds, run time dependant 6d() spring return gency listings culus acc. to UL /--14, CN/CS E :0, CE acc. to 004/108/EC & 006/95/EC Quality standard ISO 9001 Weight 4. lbs. (1.9 kg) * Variable when configured with MFT options Rated Impulse Voltage 800V, Type of action 1. (1.. for -S version), Control Pollution Degree 3. Programmed for 70 sec motor run time. t 150 sec motor run time, transformer sizing is 8.5 V and power consumption is 6 W running / 3 W holding. Valve Nominal Size Valve ody Inches DN [mm] C G(S) 1½ [137] 1.50 [38] 8.50 [16] G(S) " [156] 1.56 [40] 8.56 [17] Dimensions with G3...(D) Series 3-Way Valve C Valve Nominal Size Valve ody Inches DN [mm] C G3(D) 1½ [137] 1.6 [41] 8.6 [19] G3(D) [156] 1.87 [48] 8.87 [5] D5 N /13 - Subject to change. elimo ircontrols (US), Inc US CND LTIN MERIC

20 FX4-MFT95-X1 ctuators, Ω Dimensions with G6/G6C NSI 15 and G6 NSI 50 Series -Way Valve Dimensions with G7 and G7D NSI 15/50 Series 3-Way Valve D167_GM_NG N /13 - Subject to change. elimo ircontrols (US), Inc. D167_GM_NG_3 Valve Nominal Size Valve ody Inches DN [mm] C G6 NSI 15 ½ [9] 4.75 [11] [343] G6 NSI 15 3" [54] 5.37 [136] [354] G6 NSI 50 ½ [44] 4.75 [11] [356] G6 NSI 50 3" [73] 5.37 [136] 14.1 [359] G6C NSI 15 ½ [9] 4.75 [11] [343] G6C NSI [54] 5.37 [136] [354] Valve Nominal Size Valve ody Inches DN [mm] C-x G6 NSI 15 ½ " [9] 4.75" [11].5" [464] G6 NSI " [54] 5.37" [136] 19." [487] G6 NSI 50 ½ " [44] 4.75" [11].5" [464] G6 NSI 50 3" " [73] 5.37" [136] 19." [487] G6C NSI 15 4" " [330.] 6.87" [175] 0.5 [514] G6C NSI 15 5" " [400] 7.87" [00] 0.87 [530] G6C NSI 15 6" " [451] 8.50" [16] 1.50 [546] Valve Nominal Size Valve ody Inches DN [mm] C G7 & G7D NSI 15 ½ [9] 7.1 [1] [35] G7 & G7D NSI [54] 8.00 [03] [367] G7D NSI [330] 9.87 [51] 15.5 [387] G7 & G7D NSI 50 ½ [44] 7.37 [7] [356] G7 & G7D NSI [73] 8.37 [13] 14.6 [371] G7D NSI [346] 10.5 [60] 15.5 [387] Valve Nominal Size Valve ody Inches DN [mm] C-x G7 NSI 15 ½ [9] 7.1 [1].5 [464] G7 NSI [54] 8.00 [03] 19. [487] G7 NSI [330.] 9.87 [51] 0.00 [508] G7D NSI [305] [67].37 [467] G7D NSI [359] 11.1 [8] 19. [487] G7 NSI 50 ½ [44] 7.37 [7].75 [476] G7 NSI [73] 8.37 [13] [49] G7 NSI [346] 10.5 [60] 0.37 [517] G7D NSI [37] [79] 0.56 [5] G7D NSI [368] [9] 1.5 [540] US CND LTIN MERIC 81

21 FX4-MFT95-X1 ctuators, Ω Proportional Potentiometric Control - Wiring Diagrams 5 ctuators with plenum rated cable do not have numbers on wires; use color codes instead. ctuators with appliance cables are numbered. 1 Provide overload protection and disconnect as required. WRNING Live Electrical Components! During installation, testing, servicing and troubleshooting of this product, it may be necessary to work with live electrical components. Have a qualifi ed licensed electrician or other individual who has been properly trained in handling live electrical components perform these tasks. Failure to follow all electrical safety precautions when exposed to live electrical components could result in death or serious injury. ctuators and controller must have separate transformers. 3 Consult controller instruction data for more detailed information. Resistor value depends on the type of controller and the number of actuators. No 4 resistor is used for one actuator. Honeywell resistor kits may also be used. 5 To reverse control rotation, use the reversing switch. Wire Colors 1 = lack = Red Override Switch Switch Damper Position Damper Open Damper Closed The direction of rotation switch is set so that the fail safe position and the position of the damper is closed with no signal at wire R. Low Limit Control Series 90 Controller 135 Ω W R W R Controller W Series 90 low limit control 135 Ω for 0 to 50% control 80 Ω for 0 to 100% control High Limit Control Series 90 Controller 3 = White 4 = Pink R W R Series 90 high limit control - 80 Ω R W 5 = Gray 6 = Orange Pnk (4) W Wht (3) R Gry (5) Org (6) U5 Output to 10 VDC -MFT95-X1 Pnk (4) W Wht (3) R Gry (5) Org (6) U5 Output to 10 VDC -MFT95-X1 Pnk (4) W Wht (3) R Gry (5) Org (6) U5 Output to 10 VDC -MFT95-X1 Pnk (4) W Wht (3) R Gry (5) Org (6) U5 Output to 10 VDC -MFT95-X1 W015 W016 W017 Wiring Multiple ctuators to a Series 90 Controller Shunting Resistor W R Series 90 Controller No. of actuators Resistance 140 Ω Ω Ω Ω 6 8 Ω To other actuators Pnk (4) W Wht (3) R Gry (5) Org (6) U5 Output to 10 VDC -MFT95-X1 Pnk (4) W Wht (3) R Gry (5) Org (6) U5 Output to 10 VDC -MFT95-X1 Wiring Multiple ctuators to a Series 90 Controller using a Minimum Position Potentiometer Series 90 Controller R W R W R W H05 Changeover Occupied Controller Contact S963 Minimum Position Potentiometer Pnk (4) W Wht (3) R Gry (5) Org (6) U5 Output to 10 VDC -MFT95-X1 Pnk (4) W Wht (3) R Gry (5) Org (6) U5 Output to 10 VDC -MFT95-X1 W0 W019 Typical wiring diagrams for multiple actuators used with the W973, W7100 and T775 controllers H05 Changeover Controller W Shunting Resistor No. of actuators Resistance 1300 Ω Ω Ω W973, W7100 Controller Y R W973, W7100 T775 W R R R W W R W Q09 Minimum Position Potentiometer To other actuators Pnk (4) W Wht (3) R Gry (5) Org (6) U5 Output to 10 VDC -MFT95-X1 Occupied Contact Honeywell T675 Morning Warmup Pnk (4) W Wht (3) R Gry (5) Org (6) U5 Output to 10 VDC Honeywell Q09 Minimum Position Potentiometer -MFT95-X1 Used with the W973 and W7100 controllers R R W W Honeywell T675 Morning Warmup Pnk (4) W Wht (3) R Gry (5) Org (6) U5 Output to 10 VDC -MFT95-X1 Pnk (4) W Wht (3) R Gry (5) Org (6) U5 Output to 10 VDC -MFT95-X1 W00 N /13 - Subject to change. elimo ircontrols (US), Inc US CND LTIN MERIC