HD(U) Series Valves HVAC Service Butterfly Valves 2-way and 3-way Assemblies

Transcription

1 Features / enefits utterfly Valves H(U) Series Valves HV Service utterfly Valves 2-way and 3-way ssemblies elimo resilient seat H(U)... Series utterfly Valves are designed for use in NSI lass 150 piping systems and are supplied in standard lug style body designs. VLVE ESIGN FETURES Unique seat and disc design ensures positive valve sealing while maintaining low seating torque utterfly valve discs are precision machined to half ball profile, providing a precise disc-to-seat relationship artridge style seat incorporates an elastomer bonded to a phenolic stabilizing ring, eliminating elastomer movement and reducing seat tearing or fatiguing due to bunching artridge seat has a much smaller mass of elastomer than traditional boot seat designs, limiting seat swell and the accompanying variations in seating torque The five bushing design completely isolates the valve shaft from the body, resulting in increased control of the valve disc, lower valve seating torque, and longer valve life uctile Iron Full Lug odies EPM liner Stainless Steel isc Two Models to suit the application: HU Series provides economical HV solutions up to 50 psi close-off with a 200 psi body rating H Series provides full-rated close-off to 200 psi (2 12 ) or 150 psi (14 30 ) 2-way and 3-way applications ISO5211 ESIGN UTILE IRON OY I TG RPTFE TOP USHING EPM O-RING RPTFE USHINGS NSI OLT PTTERN EPM SET PIN 304SS IS 416SS SHFT RPTFE LOWER USHING 1

2 ...H(U) Series utterfly Valves Standard ctuation (verage ssembly Weights) UNERUT MOELS FULL RTE MOELS 3-WY 2-WY 3-WY 2-WY TUTOR NON-SPRING RETURN SPRING RETURN Size Valve Max GPM OP M(X) GM(X) 2*GM(X) F... 2*F... 2 F650HU lbs. 14 lbs. 2.5 F665HU lbs. 14 lbs. 3 F680HU lbs. 25 lbs. 4 F6100HU lbs. 34 lbs. 5 F6125HU lbs. 39 lbs. 6 F6150HU lbs. 2 F750HU lbs. 46 lbs. 2.5 F765HU lbs. 65 lbs. 3 F780HU lbs. 72 lbs. 4 F7100HU lbs. 5 F7125HU lbs. 6 F7150HU lbs. NON-SPRING RETURN SPRING RETURN Size Valve Max GPM OP M(X) GM(X) 2*GM(X) F... 2*F... 2 F650H lbs. 14 lbs. 2.5 F665H lbs. 24 lbs. 3 F680H lbs. 25 lbs. 4 F6100H lbs. 2 F750H lbs. 46 lbs. 2.5 F765H lbs. 65 lbs. 3 F780H lbs. 4 F7100H lbs. 2

3 ...H Series utterfly Valves Industrial ctuation (verage ssembly Weights) UNERUT MOELS 2-WY 3-WY TUTOR NON-SPRING RETURN Size Valve Max GPM OP SY1 SY2 SY3 SY4 2 F650HU lbs. 2.5 F665HU lbs. 3 F680HU lbs. 4 F6100HU lbs. 5 F6125HU lbs. 6 F6150HU lbs. 8 F6200HU lbs. 10 F6250HU lbs. 12 F6300HU lbs. 2 F750HU lbs 2.5 F765HU lbs. 3 F780HU lbs. 4 F7100HU lbs. 5 F7125HU lbs. 6 F7150HU lbs. 8 F7200HU lbs. 10 F7250HU lbs. 12 F7300HU lbs. Max GPM = Maximum US gallons of water (gpm) per minute, at room temperature, that will flow through the fully open valve without exceeding design velocity limits. OP = lose-off Pressure stated in psi. This is the maximum differential pressure the valve will close-off against while maintaining a bubble tight seal. ll SY series actuators are NEM 4X rated and include 2 auxiliary switches and a heater. FULL RTE MOELS 2-WY 3-WY TUTOR NON-SPRING RETURN Size Valve Max GPM OP SY2 SY3 SY4 SY6 SY7 SY8 SY10 SY12 2 F650H lbs. 2.5 F665H lbs. 3 F680H lbs. 4 F6100H lbs. 5 F6125H lbs. 6 F6150H lbs. 8 F6200H lbs. 10 F6250H lbs. 12 F6300H lbs. 14 F6350H lbs. 16 F6400H lbs. 18 F6450H lbs. 20 F6500H lbs. 24 F6600H lbs. 30 F6750H lbs. 2 F750H lbs. 2.5 F765H lbs. 3 F780H lbs. 4 F7100H lbs. 5 F7125H lbs. 6 F7150H lbs. 8 F7200H lbs. 10 F7250H lbs. 12 F7300H lbs. 14 F7350H lbs. 16 F7400H lbs. 18 F7450H lbs. 20 F7500H lbs. 24 F7600H lbs. 3

4 utterfly Valve Selection-Velocity hart HU/H Series Valves MSTER OMMON OMMON MSTER SLVE MSTER 163 OMMON SLVE SLVE ONFIG OE X10 ON/OFF OR MSTER VLVE IS MSTER FIL NON-FIL ONFIG OE X20 ON/OFF OR MO@2V MSTER VLVE IS MSTER FIL NON-FIL ONFIG OE X30 ON/OFF OR MO@2V MSTER VLVE IS MSTER FIL NON-FIL X11 X21 X31 X12 LOSE X22 LOSE X32 LOSE X13 LOSE NON-FIL X23 LOSE NON-FIL X33 LOSE NON-FIL X14 LOSE X24 LOSE X34 LOSE X15 LOSE LOSE X25 LOSE LOSE X35 LOSE LOSE X Specifies i-irectional Flow apability Notes: 1. Slave Valve operates inversely of the Master Valve. 2. The Master Valve is always located on the run. 3. The Slave Valve may also have an actuator if required (irect oupled). 4. On/Off actuator normal position is a function of field logic. 5. Proportional actuator normal position is a function of the W/W 6. ll 3-way assemblies are designed for 90 degree actuator rotation. Flow in Std Weight Pipe (Fluid Velocity in GPM). Use with Resilient Seat F Valves. Size 2 FPS 4 FPS 6 FPS 8 FPS 10 FPS 12 FPS 14 FPS 16 FPS ½ It is not recommended to exceed 12 feet per second through resilient seat butterfly valves. Velocities greater than 12 fps may damage the valve liner and disc. If the maximum recommended velocity is exceeded, the valve may be damaged and/or the torque increased potentially exceeding the actuators capacity. 4

5 utterfly Valve Selection-Velocity hart 150 SHP/300 SHP Series Valves SHP Series Valves are Flow irection Specific MIXING MSTER FLOW OMMON OMMON FLOW MSTER SLVE FLOW MSTER 145 OMMON SLVE SLVE IVERTING MSTER FLOW OMMON OMMON FLOW MSTER SLVE FLOW MSTER OMMON SLVE SLVE ONFIG OE M()10 M()11 M()12 M()13 M()14 ON/OFF OR MSTER VLVE IS LOSE LOSE MSTER FIL NON-FIL LOSE NON-FIL M()15 LOSE LOSE M Specifies MIXING, Specifies IVERTING ONFIG OE M()20 M()21 M()22 M()23 M()24 M()25 Notes: 1. Slave Valve operates inversely of the Master Valve. 2. The Master Valve is always located on the run. 3. The Slave Valve may also have an actuator if required (irect oupled). ON/OFF OR MO@2V MSTER VLVE IS LOSE LOSE LOSE MSTER FIL NON-FIL LOSE NON-FIL LOSE ONFIG OE M()30 M()31 M()32 M()33 M()34 M()35 ON/OFF OR MO@2V MSTER VLVE IS LOSE LOSE LOSE MSTER FIL NON-FIL LOSE NON-FIL LOSE 4. On/Off actuator normal position is a function of field logic. 5. Proportional actuator normal position is a function of the W/W switc 6. ll 3-way assemblies are designed for 90 degree actuator rotation. Flow in Std Weight Pipe (Fluid Velocity in GPM). Use with SHP Series F Valves. SIZE 4 FPS 8 FPS 12 FPS 16 FPS 20 FPS 24 FPS 28 FPS 32 FPS 36 FPS ½ It is not recommended to exceed 32 feet per second through high performance butterfly valves. Velocities greater than 32 fps may damage the valve. 5

6 utterfly Valve Nomenclature F6 50 H SY2-24 MFT Valve F6 = 2-way F7 = 3-way Valve Size = 2 to 30 Trim Material HU = Stainless isc, ast uctile Iron Full Lug ody, EPM Liner, ubble Tight lose-off to 50 psi H = Stainless isc, ast uctile Iron Full Lug ody, EPM Liner, ubble Tight lose-off to 200 psi (2 to 12 ), 150 psi (14 +) -150SHP = NSI lass 150, Stainless isc, ast Steel Full Lug ody, RPTFE Seat, ubble Tight loseoff up to 285 psi -300SHP = NSI lass 150, Stainless isc, ast Steel Full Lug ody, RPTFE Seat, ubble Tight loseoff up to 600 psi ctuator Type Non-Spring Return R... GR... GM(X) SY Electronic Fail- Safe GK... Spring Return F Power Supply -24 = 24 V/ -110 = 110/120 V -120 = 120 V -230 = 230 V ontrol lank = On/Off -3-X1 = On/Off, Floating Point MFT or MFT-X1 = Multi-Function Technology -S = uilt-in uxiliary Switch ORERING EXMPLE Non-Spring Return Spring Return 2 Pos. Modulating 1 hoose the valve actuator combination. N NO NO/FO N/F NO/FO NO/F N/FO N/F 2 2-way Preference F650H+SY2-24MFT +NO +Tagging (if needed) Set Up Required Field Logic etermines Normal Position (Normally losed) 1 V/2 V/4m = losed (Normally Open) 1 V/2 V/4m = Open Specify preference or configuration. (Normally Open/Fail Open) Field Logic etermines Normal Position Spring Fails Valve (Normally losed/fail losed) Field Logic etermines Normal Position Spring Fails Valve LOSE (Normally Open/Fail Open) 1 V/2 V/4m = Open Spring Fails Valve (Normally Open/Fail losed) 1 V/2 V/4m = Open Spring Fails Valve LOSE (Normally losed/fail Open) 1 V/2 V/4m = losed Spring Fails Valve (Normally losed/fail losed) 1 V/2 V/4m = losed Spring Fails Valve LOSE Non-Spring Return Spring Return Set-Up 2 Pos. Modulating Modulating 2 Pos. 3 Specify Flow Pattern [10-35] Specify Flow Pattern [10-35] For MFT orders only - select programming code (consult factory) 3-way onfiguration No Set Up Required Field Logic etermines Normal Position Master (ctuated) Valve N (Normally losed) 1 V/2 V/4m = losed Master (ctuated) Valve NO (Normally Open) 1 V/2 V/4m = Open NO/FO (Normally Open/Fail Open) Field Logic etermines Normal Position Spring Fails Master Valve N/F (Normally losed/fail losed) Field Logic etermines Normal Position Spring Fails Master Valve LOSE NO/FO (Normally Open/Fail Open) 1 V/2 V/4m = Master Valve Open Spring Fails Master Valve NO/F (Normally Open/Fail losed) 1 V/2 V/4m = Maser Valve Open Spring Fails Master Valve LOSE N/FO (Normally losed/fail Open) 1 V/2 V/4m = Master Valve losed Spring Fails Master Valve N/F (Normally losed/fail losed) 1 V/2 V/4m = Master Valve losed Spring Fails Master Valve LOSE 4 oes order require tagging? Tagging: Valves may be tagged per customer specification. ($10.00 per tag) Example: hiller 1 3rd Floor East Part number for tagging: omplete Ordering Example: F650H+SY2-24MFT+NO +E onsult factory 6

7 F6 HU utterfly Valves 2 12 uctile Iron Lug ody Resilient Seat, 304 Stainless isc 50 psi bubble tight shut-off Long stem design allows for 2 insulation Valve face-to-face dimensions comply with PI 609 & MSS-SP-67 ompletely assembled and tested, ready for installation pplication These valves are designed to meet the needs of HV and commercial applications requiring bubble tight shut-off for liquids. Typical applications include chiller isolation, cooling tower isolation, change-over systems, large air handler coil control, bypass and process control applications. The large v values provide for an economical control valve solution for larger flow applications. esigned for use in Victaulic piping systems when mated to Victaulic 41 series flange nipples. Jobsite Note Valves should be stored in a weather protected area prior to construction. omplete installation recommendations can be found in elimo s Installation and Maintenance Instructions for F6/F7 H/HU utterfly Valves. Technical ata Service chilled, hot water, 60% glycol Flow characteristic modified equal percentage ction 90 rotation Sizes 2 to 12 Type of end fitting for use with NSI lass 125/150 flanges Materials ody ductile iron STM 536 ody finish epoxy powder coated isc 304 stainless steel Seat EPM Shaft 416 stainless steel O-ring EPM Upper bushing RPTFE Middle bushings RPTFE Lower bushing RPTFE Media temperature range -22 F to 250 F [-30 to 120 ] Operation ambient temperature range -22 F to 122 F [-30 to 50 ] ody pressure rating SME/NSI lass 125/150 (200 psi at -30 F to 275 F) lose-off pressure 50 psi Rangeability 10:1 (for 30 to 70 range) Maximum velocity 12 FPS Valve Nominal Size Type Suitable ctuators v v IN N [mm] 2-way Spring Non-Spring F650HU ½ 65 F665HU F680HU F6100HU F6125HU F6150HU F6200HU F6250HU F6300HU MO ON/OFF Valve Size v F650HU F665HU 2½ F680HU F6100HU F6125HU F6150HU F6200HU F6250HU F6300HU F Series M Series GM GM SY Series 7

8 F6 HU utterfly Valves 2 12 uctile Iron Lug ody Resilient Seat, 304 Stainless isc Maximum imensions (Inches) Valve Size v 90 v 60 (Max) H No. of Holes Lug olt ctuator lose-off (PSI) F650HU /8-11UN 50 F F665HU 2½ /8-11UN 50 F680HU /8-11UN 50 F6100HU /8-11UN 2*F 50 F6125HU /4-10UN 50 F650HU /8-11UN 50 F665HU 2½ /8-11UN M(X) 50 F680HU /8-11UN 50 F6100HU /8-11UN 50 GM(X) F6125HU /4-10UN 50 F6150HU /4-10UN GM(X) 50 F650HU /8-11UN 50 F665HU 2½ /8-11UN SY F680HU /8-11UN 50 F6100HU /8-11UN 50 F6125HU /4-10UN SY F6150HU /4-10UN 50 F6200HU /4-10UN 50 F6250HU /8-9UN SY F6300HU /8-9UN 50 Fail Safe Non-Fail Safe imension is compressed, add.125 for relaxed state. F, M and GM maximum actuator ambient temperature is 122 F. SY maximum actuator ambient temperature is 150 F. Model SY1 does not have handwheel - override is via 8mm wrench on bottom side of actuator. imensions pplication Notes 1. Valves are rated at 50 psi differential pressure in the closed position. 2. Valves are furnished with lugs tapped for use with NSI lass 125/150 flanges. Installation flanges and hardware are not included way assemblies are furnished assembled and tested, ready for installation. 4. imension allows for actuator removal without the need to remove the valve from the pipe. 5. Weather shields are available, dimensional data upon request. 6. ual actuated valves have actuators mounted on a common valve shaft. 7. elimo SY Series actuators are NEM 4X rated. Flow Pattern % OF MXIMUM FLOW F2WUIM % OF VLVE ING 100 8

9 F7 HU utterfly Valves 2 12 uctile Iron Lug ody Resilient Seat, 304 Stainless isc 50 psi bubble tight shut-off Long stem design allows for 2 insulation Valve face-to-face dimensions comply with PI 609 & MSS-SP-67 ompletely assembled and tested, ready for installation Tees comply with SME/NSI 16.1 lass 125 flanges pplication These valves are designed to meet the needs of HV and commercial applications requiring bubble tight shut off for liquids. Typical applications include chiller isolation, cooling tower isolation, change-over systems, large air handler coil control, bypass and process control applications. The large v values provide for an economical control valve solution for larger flow applications. esigned for use in Victaulic piping systems when mated to Victaulic 41 series flange nipples. Jobsite Note Valves should be stored in a weather protected area prior to construction. omplete installation recommendations can be found in elimo s Installation and Maintenance Instructions for F6/F7 H/HU utterfly Valves. Technical ata Service chilled, hot water, 60% glycol Flow characteristic modified linear ction 90 rotation Sizes 2 to 12 Type of end fitting for use with NSI 125/150 flanges Materials ody ductile iron STM 536 ody finish epoxy powder finish isc 304 stainless steel Seat EPM standard Shaft 416 stainless steel O-ring EPM Upper bushing RPTFE Middle bushings RPTFE Lower bushing RPTFE Media temperature range -22 F to 250 F [-30 to 120 ] Operation ambient temperature range -22 F to 122 F [-30 to 50 ] ody pressure rating SME/NSI lass 125/150 (200 psi at -30 F to 275 F) lose-off pressure 50 psi Rangeability 10:1 (for 30 to 70 range) Maximum velocity 12 FPS Valve Nominal Size Type Suitable ctuators v v IN N [mm] 3-way Spring Non-Spring F750HU ½ 65 F765HU F780HU F7100HU F7125HU F7150HU F7200HU F7250HU F7300HU MO ON/OFF Valve Size v F750HU F765HU 2½ F780HU F7100HU F7125HU F7150HU F7200HU F7250HU F7300HU F Series M GM Series SY Series 9

10 0 F7 HU utterfly Valves 2 12 uctile Iron Lug ody Resilient Seat, 304 Stainless isc Maximum imensions (Inches) Valve Size v 90 (Max) H No. of Holes Lug olt ctuator lose-off (PSI) F750HU /8-11UN F 50 F765HU 2½ /8-11UN 50 2*F F780HU /8-11UN 50 F750HU /8-11UN 50 SY1 F765HU 2½ /8-11UN 50 F780HU /8-11UN 50 F7100HU /8-11UN 50 SY2 F7125HU /4-10UN 50 F7150HU /4-10UN 50 F7200HU /4-10UN SY3 50 F7250HU /8-9UN 50 SY4 F7300HU /8-9UN 50 Fail Safe Non-Fail Safe F maximum actuator ambient temperature is 122 F. SY... maximum actuator ambient temperature is 150 F. Model SY1 does not have hand wheel-override is via 8mm wrench on bottom side of actuator. imensions HS WGP15 pplication Notes 1. Valves are rated at 50 psi differential pressure in the closed position. 2. Valves are furnished with lugs tapped for use with NSI lass 125/150 flanges. Installation flanges and hardware are not included way assemblies are furnished assembled and tested, ready for installation. ll 3-way assemblies require the customer to specify the 3-way configuration prior to order entry to guarantee correct placement of valves and actuators on the assembly. 4. imension allows for actuator removal without the need to remove the valve from the pipe. 5. Weather shields are available, dimensional data upon request. 6. ual actuated valves have single actuators mounted on each valve shaft. 7. olts supplied are for shipping purposes only. Upon installation replace with an appropriate SE grade 5 or better hardware. 8. elimo SY Series actuators are NEM 4X rated. S 10

11 F6 H utterfly Valves 2 30 uctile Iron Lug ody Resilient Seat, 304 Stainless isc 200 psi (2 to 12 ) and 150 psi (14-30 ) bubble tight shut-off Long stem design allows for 2 insulation Valve face-to-face dimensions comply with PI 609 & MSS-SP-67 ompletely assembled and tested, ready for installation pplication These valves are designed to meet the needs of HV and commercial applications requiring bubble tight shut-off for liquids. Typical applications include chiller isolation, cooling tower isolation, change-over systems, large air handler coil control, bypass and process control applications. The large v values provide for an economical control valve solution for larger flow applications. esigned for use in Victaulic piping systems when mated to Victaulic 41 series flange nipples. Jobsite Note Valves should be stored in a weather protected area prior to construction. omplete installation recommendations can be found in elimo s Installation and Maintenance Instructions for F6/F7 H/HU utterfly Valves. Technical ata Service chilled, hot water, 60% glycol Flow characteristic modified equal percentage ction 90 rotation Sizes 2 to 30 Type of end fitting for use with NSI 125/150 flanges Materials ody ductile iron STM 536 ody finish epoxy powder coated isc 304 stainless steel Seat EPM standard Shaft 416 stainless steel O-ring EPM Upper bushing RPTFE Middle bushings RPTFE Lower bushing RPTFE Media temperature range -22 F to 250 F [-30 to 120 ] Operation ambient temperature range -22 F to 122 F [-30 to 50 ] ody pressure rating SME/NSI lass 125/150 (200 psi at -30 F to 275 F) lose-off pressure 200 psi (2-12 ), 150 psi (14-30 ) Rangeability 10:1 (for 30 to 70 range) Maximum velocity 12 FPS Valve Nominal Size Type Suitable ctuators v v IN N [mm] 2-way Spring Non-Spring F650H ½ 65 F665H F680H F6100H F6125H F6150H F6200H F6250H F6300H F6350H F6400H F6450H F6500H F6600H F6750H MO ON/OFF Valve Size v F650H F665H 2-1/ F680H F6100H F6125H F6150H F6200H F6250H F6300H F6350H F6400H F6450H F6500H F6600H F6750H F Series M GM SY Series 11

12 F6 H utterfly Valves 2 30 uctile Iron Lug ody Resilient Seat, 304 Stainless isc Maximum imensions (Inches) Valve Size v 90 v 60 (Max) H No. of Holes Lug olt ctuator lose-off (PSI) F650H /8-11UN F 200 F665H 2½ /8-11UN 200 F680H /8-11UN 2*F 200 F650H /8-11UN 200 M(X) F665H 2½ /8-11UN 200 F680H /8-11UN GM(X) 200 F6100H /8-11UN 2*GM(X) 200 Valve Size v 90 v 60 (Max) (Max) (Max) (Max) H No. of Holes Lug olt ctuator lose-off (PSI) F650H /8-11UN 200 F665H 2½ /8-11UN 200 F680H /8-11UN SY2 200 F6100H /8-11UN 200 F6125H /4-10UN 200 F6150H /4-10UN SY3 200 F6200H /4-10UN 200 F6250H /8-9UN SY4 200 F6300H /8-9UN 200 F6350H UN SY5 150 F6400H UN SY6 150 F6450H /8-7UN 150 SY8 F6500H /8-7UN 150 F6600H /4-7UN SY F6750H /4-7UN SY Fail Safe Non-Fail Safe Non-Fail Safe imension is compressed, add.125 for relaxed state. SY6 and larger available in 110/220 V versions only. F, M and GM maximum actuator ambient temperature is 122 F. SY... maximum actuator ambient temperature is 150 F. imensions F2WUIM pplication Notes 1. Valves are rated at 200 psi differential pressure in the closed position (SY psi 14 +). 2. Valves are furnished with lugs tapped for use with NSI lass 125/150 flanges. Installation flanges and hardware are not included way assemblies are furnished assembled and tested, ready for installation. 4. imension allows for actuator removal without the need to remove the valve from the pipe. 5. Weather shields are available, dimensional data upon request. 6. ual actuated valves have actuators mounted on a common valve shaft. 7. elimo SY Series actuators are NEM 4X rated. Flow Pattern % OF MXIMUM FLOW % OF VLVE ING 12

13 F7 H utterfly Valves 2 24 uctile Iron Lug ody Resilient Seat, 304 Stainless isc 200 psi (2 to 12 ) and 150 psi (14-30 ) bubble tight shut-off Long stem design allows for 2 insulation Valve face-to-face dimensions comply with PI 609 & MSS-SP-67 ompletely assembled and tested, ready for installation Tees comply with SME/NSI 16.1 lass 125 flanges pplication These valves are designed to meet the needs of HV and commercial applications requiring bubble tight shut off for liquids. Typical applications include chiller isolation, cooling tower isolation, change-over systems, large air handler coil control, bypass and process control applications. The large v values provide for an economical control valve solution for larger flow applications. esigned for use in Victaulic piping systems when mated to Victaulic 41 series flange nipples. Fail safe operation is possible with NSV-SY series battery backup systems. Jobsite Note Valves should be stored in a weather protected area prior to construction. omplete installation recommendations can be found in elimo s Installation and Maintenance Instructions for F6/F7 H/HU utterfly Valves. Technical ata Service chilled, hot water, 60% glycol Flow characteristic modified linear ction 90 rotation Sizes 2 to 24 Type of end fitting for use with NSI 125/150 flanges Materials: ody ductile iron STM 536 ody finish epoxy powder coated isc 304 stainless steel Seat EPM standard Shaft 416 stainless steel O-ring EPM Upper bushing RPTFE Middle bushings RPTFE Lower bushing RPTFE Media temperature range -22 F to 250 F [-30 to 120 ] Operation ambient temperature range -22 F to 122 F [-30 to 50 ] ody pressure rating SME/NSI lass 125/150 (200 psi at -30 F to 275 F) lose-off pressure 200 psi (2-12 ), 150 psi (14-24 ) Rangeability 10:1 (for 30 to 70 range) Maximum Velocity 12 FPS Valve Nominal Size Type Suitable ctuators v v IN N [mm] 2-way Spring Non-Spring F750H ½ 65 F765H F780H F7100H F7125H F7150H F7200H F7250H F7300H F7350H F7400H F7450H F7500H F7600H MO ON/OFF Valve Size v F750H F765H 2½ F780H F7100H F7125H F7150H F7200H F7250H F7300H F7350H F7400H F7450H F7500H F7600H F Series M GM Series SY Series 13

14 F7 H utterfly Valves 2 24 uctile Iron Lug ody Resilient Seat, 304 Stainless isc Maximum imensions (Inches) Valve Size v 90 (Max) H No. of Holes Lug olt ctuator lose-off (PSI) F750H /8-11UN F 200 F765H 2½ /8-11UN 2*F 200 F750H /8-11UN 200 F765H 2½ /8-11UN 200 SY2 F780H /8-11UN 200 F7100H /8-11UN 200 F7125H /4-10UN 200 SY3 F7150H /4-10UN 200 F7200H /4-10UN 200 SY4 F7250H /8-9UN 200 F7300H /8-9UN SY5 200 F7350H UN SY6 150 F7400H UN SY7 150 F7450H /8-7UN 150 SY9 F7500H /8-7UN 150 F7600H /4-7UN SY Fail Safe Non-Fail Safe F maximum actuator ambient temperature is 122 F. SY... maximum actuator ambient temperature is 150 F. SY6 and larger available in 110/220 V versions only. pplication Notes 1. Valves are rated at 200 psi differential pressure in the closed position. 2. Valves are furnished with lugs tapped for use with NSI lass 125/150 flanges. Installation flanges and hardware are not included way assemblies are furnished assembled and tested, ready for installation. ll 3-way assemblies require the customer to specify the 3-way configuration prior to order entry to guarantee correct placement of valves and actuators on the assembly. 4. imension allows for actuator removal without the need to remove the valve from the pipe. 5. elimo SY Series actuators are NEM 4X rated. 5. Weather shields are available, dimensional data upon request. 6. ual actuated valves have single actuators mounted on each valve shaft. 7. olts supplied are for shipping purposes only. Upon installation replace with an appropriate SE grade 5 or better hardware Way onfiguration odes MSTER Note: For tee configuration, please refer to page 4. SLVE ON/OFF OR ONFIG MO@2V MSTER MSTER VLVE OE VLVE FIL X10 NON-FIL X11 X12 LOSE X13 LOSE NON-FIL X14 LOSE X15 LOSE LOSE X Specifies i-irectional Flow apability OMMON ONFIG OE X20 X21 X22 X23 OMMON X24 X25 SLVE ON/OFF OR MO@2V MSTER VLVE IS LOSE LOSE LOSE MSTER MSTER FIL NON-FIL LOSE NON-FIL LOSE SLVE ONFIG OE X30 X31 X32 X33 X34 X35 OMMON LOSE LOSE LOSE imensions ON/OFF OR MO@2V MSTER VLVE IS MSTER FIL NON-FIL LOSE NON-FIL LOSE MSTER NOTES 1. Slave Valve operates inversely of the Master Valve. 2. The Master Valve is always located on the run. 3. The Slave Valve may also have an actuator if required (irect oupled). 4. On/Off actuator normal position is a function of field logic. 5. Proportional actuator normal position is a function of the W/W switch. 6. ll 3-way assemblies are designed for 90 degree actuator rotation. ORERING INFORMTION Please note that H series F valves over 18 and LL sizes 3-way tee assemblies ordered with onfiguration odes are special order/custom built and are NOT returnable. HS WG11 14

15 Features and enefits SHP Series High Performance utterfly Valves Valve esign Features elimo SHP... Series utterfly Valves are designed for use in NSI lass 150 and NSI lass 300 piping systems and are supplied in standard lug style body designs. Unique seat and disc design provides i-irectional bubble tight shutoff at rated pressure/temperatures The Soft Seat design creates a self-energized seal in vacuum-to-low pressure applications Under high pressure conditions, the seat is also designed to permit, confine and direct movement of the seat against the disc edge, up to the full NSI lass 150 or 300 old Working Pressures The Soft Seat is designed for high services with minimal wear and low torque Seat replacement is a simple operation, requiring no special tools Valve ody is Full Lug type cast in arbon Steel isc is cast in F8M Stainless Steel Shaft is 17-4pH Stainless for superior strength Soft Seat is RPTFE for increased wear resistance and low torque Top Mounted Gland Flange easily accessible without removing actuator or mounting brackets KEY Square key valve-to-operator connection provides an externally controlled failure point upon over-torquing. GLN FLNGE pplies load against packing gland to prevent external leakage. Fully adjustable. PKING hevron design TFE prevents external leakage out valve neck to full NSI hydrostatic shell test pressures (150% of.w.p.). WEGE RING Stainless steel band wedged between valve body and retainer ring by set screws to lock seat and retainer ring in position on valve sizes 2 through 30. Socket head cap screws are used on valve sizes 36 and larger. SET SREWS one point screws force wedge ring outward to lock seat retainer in position on valve sizes 2 through 30. Socket head cap screws are used on valve sizes 36 and larger. OVERTRVEL STOP Prevents disc from rotating into wrong quadrant. SOFT-SET Patented bidirectional seat with encapsulated elastomeric o-ring core for resiliency. ommon seat materials include TFE, RTFE and UHMWPE. LOW OUT PROOF SHFT Solid shaft provides alignment and rigid support for disc. PKING GLN Separate part from gland flange, preventing uneven load distribution against packing. ERINGS oth above and below the disc, bearings are of composite design: PTFE bonded to epoxy-glass filament wound ring. Used to align shaft, with high capacity, low wear and low friction coefficient. IS SPERS isc is centered by use of thrust spacers around shaft in sizes 2 to 5. isc position stops or thrust bolt arrangements are used for larger valve sizes. WEGE PINS Provide positive mechanical attachment of disc to shaft. OY NSI design in either wafer or lug configuration. IS 360 uninterrupted spherical edge for sealing. Profile is designed for maximum flow and equal percentage control. RETINER RING Retains seat in valve. Standard surface finish is 125 to 200 RH and is compatible with both standard gaskets and spiral wound gasket designs. Outside diameter is recessed within gasket sealing surface to prevent external leakage. 15

16 utterfly Valves Pressure/Temperature Ratings Pressure/Temperature Ratings s temperature increases, the pressure retaining capability of materials decreases. The graph below illustrates the pressure/temperature ratings of the elimo NSI lass 150 and lass 300 valves. The heavy lines define the ratings of the carbon steel and stainless steel valve body (or shell ) in conformance to NSI The shaded areas define the ratings of the PTFE and RPTFE Seat materials. Seat ratings are based on differential pressure with the disc in the fully closed position. NSI ody and Flowseal Soft Pressure - Temperature Ratings Steam Service RPTFE seated valves are rated for 50 psi saturated steam. 16

17 ...SHP Series utterfly Valves verage ssembly Weights NSI way 3-way Non-Spring Return Spring Return Size Valve Model Max GPM OP ctuator Weight 2*F Weight 2 F SHP *F24 US 24 lbs. 285 GM(X)24 18 lbs. 2.5 F SHP *F24 US 24 lbs. 285 GM(X)24 18 lbs *F24 US 26 lbs. 3 F SHP GM(X)24 20 lbs *F24 US 38 lbs. 4 F SHP GM(X)24 32 lbs *GM(X)24 40 lbs. 2 F SHP *GM(X)24 67 lbs. 2.5 F SHP *GM(X)24 78 lbs. 3 F SHP *GM(X)24 88 lbs. 4 F SHP *GM(X) lbs. NSI way 3-way 2 F SHP *F24 US 24 lbs. 285 GM(X)24 18 lbs. 2.5 F SHP *F24 US 24 lbs. 285 GM(X)24 18 lbs *F24 US 30 lbs. 3 F SHP GM(X)24 24 lbs *F24 US 37 lbs. 4 F SHP GM(X)24 31 lbs *GM(X)24 39 lbs. 2 F SHP *GM(X)24 89 lbs. 2.5 F SHP *GM(X) lbs. 3 F SHP *GM(X) lbs. 4 F SHP *GM(X) lbs. Max GPM = Maximum US gallons of water (gpm) per minute, at room temperature, that will flow through the fully open valve without exceeding design velocity limits. OP = lose-off Pressure stated in psi. This is the maximum differential pressure the valve will close-off against while maintaining a bubble tight seal. ll SY series actuators are NEM 4X rated and include 2 auxiliary switches and a heater. 17

18 SHP Series utterfly Valves with Industrial ctuation verage ssembly Weights NSI way 3-way Non-Spring Return Size Valve Model Max GPM OP SY2-* Weight 2 F SHP SY lbs. 2.5 F SHP SY lbs. 3 F SHP SY lbs. 4 F SHP SY lbs. 5 F SHP SY lbs. 6 F SHP SY lbs. 8 F SHP SY lbs. 285 SY lbs. 10 F SHP SY lbs. 12 F SHP SY lbs. 285 SY lbs. 14 F SHP SY lbs. 285 SY lbs. 16 F SHP SY lbs. 18 F SHP SY lbs. 285 SY lbs. 20 F SHP SY lbs. 285 SY lbs. 24 F SHP SY lbs. 30 F SHP SY lbs. 2 F SHP SY lbs. 2.5 F SHP SY lbs. 3 F SHP SY lbs. 4 F SHP SY lbs. 5 F SHP SY lbs. 6 F SHP SY lbs. 8 F SHP SY lbs. 10 F SHP SY lbs. 285 SY lbs. 12 F SHP SY lbs. 285 SY lbs. 14 F SHP SY lbs. 16 F SHP SY lbs. 150 SY lbs. 18 F SHP SY lbs. 285 SY lbs. 20 F SHP SY lbs. 285 SY lbs. 24 F SHP SY lbs. Max GPM = Maximum US gallons of water (gpm) per minute, at room temperature, that will flow through the fully open valve without exceeding design velocity limits. OP = lose-off Pressure stated in psi. This is the maximum differential pressure the valve will close-off against while maintaining a bubble tight seal. ll SY series actuators are NEM 4X rated and include 2 auxiliary switches and a heater. 18

19 SHP Series utterfly Valves with Industrial ctuation verage ssembly Weights NSI way Non-Spring Return Size Valve Model Max GPM OP ctuator Weight 2 F SHP SY lbs. 2.5 F SHP SY lbs. 3 F SHP SY lbs. 4 F SHP SY lbs. 5 F SHP SY lbs. 600 SY lbs. 6 F SHP SY lbs. 600 SY lbs. 150 SY lbs. 8 F SHP SY lbs. 285 SY lbs. 400 SY lbs. 10 F SHP SY lbs. 150 SY lbs. 285 SY lbs. 12 F SHP SY lbs. 150 SY lbs. 400 SY lbs. 14 F SHP SY lbs. 150 SY lbs. 285 SY lbs. 400 SY lbs. 16 F SHP SY lbs. 150 SY lbs. 285 SY lbs. 400 SY lbs. 18 F SHP SY lbs. 150 SY lbs. 20 F SHP SY lbs. 400 SY lbs. 24 F SHP SY lbs. Max GPM = Maximum US gallons of water (gpm) per minute, at room temperature, that will flow through the fully open valve without exceeding design velocity limits. OP = lose-off Pressure stated in psi. This is the maximum differential pressure the valve will close-off against while maintaining a bubble tight seal. ll SY series actuators are NEM 4X rated and include 2 auxiliary switches and a heater. 19

20 SHP Series utterfly Valves with Industrial ctuation verage ssembly Weights NSI way Non-Spring Return Size Valve Model Max GPM OP ctuator Weight 2 F SHP SY lbs. 600 SY lbs. 2.5 F SHP SY lbs. 600 SY lbs. 3 F SHP SY lbs. 600 SY lbs. 4 F SHP SY lbs. 600 SY lbs. 5 F SHP SY lbs. 600 SY lbs. 6 F SHP SY lbs. 600 SY lbs. 400 SY lbs. 8 F SHP SY lbs. 150 SY lbs. 285 SY lbs. 10 F SHP SY lbs. 150 SY lbs. 400 SY lbs. 12 F SHP SY lbs. 150 SY lbs. 400 SY lbs. 14 F SHP SY lbs. 150 SY lbs. 285 SY lbs. 16 F SHP SY lbs. 600 SY lbs. 150 SY lbs. 285 SY lbs. 18 F SHP SY lbs. 150 SY lbs. 20 F SHP SY lbs. 24 F SHP SY lbs. Max GPM = Maximum US gallons of water (gpm) per minute, at room temperature, that will flow through the fully open valve without exceeding design velocity limits. OP = lose-off Pressure stated in psi. This is the maximum differential pressure the valve will close-off against while maintaining a bubble tight seal. ll SY series actuators are NEM 4X rated and include 2 auxiliary switches and a heater. 20

21 F6 NSI lass 150 Reinforced Teflon Seat, 316 Stainless isc ubble tight shut-off to NSI lass 150 Standards Long stem design allows for 2 insulation minimum Valve Face-to-face dimensions comply with PI 609 & MSS-SP-68 esigned to be installed between SME/NSI 16.5 Flanges ompletely assembled and tested, ready for installation pplication These valves are designed to meet the needs of HV and ommercial applications requiring positive shut-off for liquids at higher pressures and temperatures. Typical applications include chiller isolation, cooling tower isolation, change-over systems, large air handler coil control, bypass and process control applications. The large v values provide for an economical control valve solution for larger flow applications. Technical ata Media service chilled, hot water, 60% glycol, steam to 50 psi Valve service double dead end service Flow characteristic modified equal percentage, unidirectional Recommended install SUS (Seat Up Stream) ction quarter turn, mechanically limited Sizes 2" to 24" Type of end fitting for use with SME/NSI 16.5 flanges Materials ody isc Seat Shaft Gland seal ushings carbon steel full lug 316 stainless steel RPTFE 17-4 PH stainless PTFE glass backed PTFE Media temperature range NSI lass 150 limitations Operation ambient temperature range -22 F to 122 F [-30 to 50 ] ody pressure rating SME/NSI lass 150 limitations lose-off pressure NSI lass 150 to F Rangeability 10:1 (for 30 deg to 70 deg range) Maximum velocity 32 FPS Valve Nominal Size Type Suitable ctuators v v IN NSI way Spring Non-Spring F SHP ½ F SHP F SHP F SHP F SHP F SHP F SHP F SHP F SHP F SHP F SHP F SHP F SHP F SHP F SHP MO ON/OFF Valve Size v F SHP F SHP F SHP F SHP F SHP F SHP F SHP F SHP F SHP F SHP F SHP F SHP F SHP F SHP F SHP F Series GM Series SY Series 21

22 F6 NSI lass 150 Reinforced Teflon Seat, 316 Stainless isc Maximum imensions (Inches) Valve Size v 90 (Max) H No. of Holes Lug olt ctuator lose-off (PSI) F SHP / F SHP / *F F SHP / F SHP / F SHP / F SHP / GM F SHP / F SHP / F SHP /8-11 2*GM 285 F SHP /8-11 UN 285 F SHP /8-11 UN 285 F SHP /8-11 UN 285 SY2 F SHP /8-11 UN 285 F SHP /4-10 UN 285 F SHP /4-10 UN 285 F SHP /4-10 UN SY3 150 SY4 285 F SHP /8-9 UN SY4 285 F SHP /8-9 UN SY4 150 SY5 285 SY5 150 F SHP UN SY7 285 SY7 150 F SHP UN SY8 285 F SHP /8-8 UN SY7 150 SY8 285 F SHP /8-8 UN SY8 150 SY F SHP /4-8 UN SY F SHP /4-8 UN SY Fail Safe Non-Fail Safe imensions Pressure/temperature chart for NSI class butterfly valves. H imension does not include flange gaskets. (2 required per valve) pplication Notes 1. Valves are rated at 285 psi differential pressure in the closed 100 F media temperature. 2. Valves are furnished with lugs tapped for use between NSI lass 125/150 flanges conforming to NSI 16.5 Standards way assemblies are furnished assembled, calibrated and tested, ready for installation. 4. imension allows for actuator(s) removal without the need to remove the valve from the pipe. 5. Weather shields are available, dimensional data furnished upon request. 6. Flange gaskets (2 required, not provided with valve) MUST be used between valve and NSI flange. 7. Flange bolts are not included with the valve. These are furnished by others. 102 Pressure PSIG Temperature NSI 600 S 1400 NSI 600 SS SHP series valves have a preferred flow direction. RPTFE RNGE -20F LOW TEMP S LIMIT NSI 300 S NSI 300 SS TFE RNGE NSI 150 S NSI 150 SS Temperature F Pressure RG F14_ PreferredFlowrate 22

23 F7 NSI lass 150 Reinforced Teflon Seat, 316 Stainless isc ubble tight shut-off to NSI lass 150 Standards Long stem design allows for 2 insulation minimum Valve Face-to-face dimensions comply with PI 609 & MSS-SP-68 esigned to be installed between SME/NSI 16.5 Flanges ompletely assembled and tested, ready for installation Tees comply with SME/NSI 16.1 lass 125 Flanges pplication These valves are designed to meet the needs of HV and ommercial applications requiring positive shut-off for liquids at higher pressures and temperatures. Typical applications include chiller isolation, cooling tower isolation, change-over systems, large air handler coil control, bypass and process control applications. The large v values provide for an economical control valve solution for larger flow applications. Technical ata Media service chilled, hot water, 60% glycol, steam to 50 psi Valve service double dead end service Flow characteristic modified linear, unidirectional Recommended install SUS (Seat Up Stream) ction quarter turn, mechanically limited Sizes 2" to 24" Type of end fitting for use with SME/NSI 16.5 flanges Materials ody isc Seat Shaft Gland seal ushings carbon steel full lug 316 stainless steel RPTFE 17-4 PH stainless PTFE glass backed PTFE Media temperature range NSI lass 150 limitations Operation ambient temperature range -22 F to 122 F [-30 to 50 ] ody pressure rating SME/NSI lass 150 limitations lose-off pressure NSI lass 150 to F Rangeability 10:1 (for 30 deg to 70 deg range) Maximum velocity 32 FPS Valve Nominal Size Type Suitable ctuators v v IN NSI way Spring Non-Spring F SHP ½ F SHP F SHP F SHP F SHP F SHP F SHP F SHP F SHP F SHP F SHP F SHP F SHP F SHP MO ON/OFF Valve Size v F SHP F SHP F SHP F SHP F SHP F SHP F SHP F SHP F SHP F SHP F SHP F SHP F SHP F SHP F Series GM Series SY Series 23

24 0 F7 NSI lass 150 Reinforced Teflon Seat, 316 Stainless isc Maximum imensions (Inches) Valve Size v 90 (Max) H No. of Holes Lug olt ctuator lose-off (PSI) F SHP / F SHP / GM(X) F SHP / F SHP / F SHP / F SHP /8-11 2*GM(X) 285 F SHP / F SHP /8-11 UN 285 F SHP /8-11 UN 285 SY2 F SHP /8-11 UN 285 F SHP /8-11 UN 285 F SHP /4-10 UN 285 SY3 F SHP /4-10 UN 285 F SHP /4-10 UN SY4 150 F SHP /8-9 UN SY4 150 SY5 285 F SHP /8-9 UN SY5 150 SY7 285 F SHP UN SY7 285 F SHP UN SY7 150 SY9 285 F SHP /8-8 UN SY8 150 SY F SHP /8-8 UN SY9 150 SY F SHP /4-8 UN SY Non-Fail Safe imensions Pressure/temperature chart for NSI class butterfly valves. imensions, and do not include flange gaskets. (3 required per valve) pplication Notes 1. Valves are rated at 285 psi differential pressure in the closed 100 F media temperature. 2. Valves are furnished with lugs tapped for use between NSI lass 125/150 flanges conforming to NSI 16.5 Standards way assemblies are furnished assembled with Tee, calibrated and tested, ready for installation. ll 3-way assemblies require the customer to specify the 3-way configuration code prior to order entry to guarantee correct placement of valves and actuator(s) on the assembly. 4. imension allows for actuator(s) removal without the need to remove the valve from the pipe. 5. Weather shields are available, dimensional data furnished upon request. 6. ual actuated valves have single actuators mounted on each valve shaft. 7. Flange gaskets (3 required, not provided with valve) MUST be used between valve and NSI flange. 8. Flange bolts are not included with the valve. These are furnished by others. S 104 Pressure PSIG Temperature NSI 600 S 1400 NSI 600 SS SHP series valves have a preferred flow direction. RPTFE RNGE -20F LOW TEMP S LIMIT NSI 300 S NSI 300 SS TFE RNGE NSI 150 S NSI 150 SS Temperature F Pressure RG F14_ PreferredFlowrate Note: For tee configuration, please refer to page 5. 24

25 F6 NSI lass 300 Reinforced Teflon Seat, 316 Stainless isc ubble tight shut-off to NSI lass 300 Standards Long stem design allows for 2 insulation minimum Valve Face-to-face dimensions comply with PI 609 & MSS-SP-68 esigned to be installed between SME/NSI 16.5 Flanges ompletely assembled and tested, ready for installation pplication These valves are designed to meet the needs of HV and ommercial applications requiring positive shut-off for liquids at higher pressures and temperatures. Typical applications include chiller isolation, cooling tower isolation, change-over systems, large air handler coil control, bypass and process control applications. The large v values provide for an economical control valve solution for larger flow applications. Technical ata Media service chilled, hot water, 60% glycol, steam to 50 psi Valve service double dead end service Flow characteristic modified equal percentage, unidirectional Recommended install SUS (Seat Up Stream) ction quarter turn, mechanically limited Sizes 2" to 24" Type of end fitting for use with SME/NSI 16.5 flanges Materials ody isc Seat Shaft Gland seal ushings carbon steel full lug 316 stainless steel RPTFE 17-4 PH stainless PTFE glass backed PTFE Media temperature range NSI lass 300 limitations Operation ambient temperature range -22 F to 122 F [-30 to 50 ] ody pressure rating SME/NSI lass 300 limitations lose-off pressure NSI lass 300 to F Rangeability 10:1 (for 30 deg to 70 deg range) Maximum velocity 32 FPS Valve Nominal Size Type Suitable ctuators v v IN NSI way Spring Non-Spring F SHP ½ F SHP F SHP F SHP F SHP F SHP F SHP F SHP F SHP F SHP F SHP F SHP F SHP F SHP MO ON/OFF Valve Size v F SHP F SHP F SHP F SHP F SHP F SHP F SHP F SHP F SHP F SHP F SHP F SHP F SHP F SHP F Series GM Series SY Series 25

26 F6 NSI lass 300 Reinforced Teflon Seat, 316 Stainless isc Maximum imensions (Inches) Valve Size v 90 (Max) H No. of Holes Lug olt ctuator lose-off (PSI) F SHP /8-11 UN 150 F SHP /4-10 UN 150 2*F F SHP /4-10 UN 150 F SHP /4-10 UN 150 F SHP /8-11 UN 285 F SHP /4-10 UN 285 GM(X) F SHP /4-10 UN 285 F SHP /4-10 UN 150 F SHP /8-11 UN 600 F SHP /4-10 UN 600 2*GM(X) F SHP /4-10 UN 600 F SHP /4-10 UN 400 F SHP /8-11 UN 600 F SHP /4-10 UN 600 SY2 F SHP /4-10 UN 600 F SHP /4-10 UN 600 F SHP /4-10 UN SY SY3 600 F SHP /4-10 UN SY2 285 SY3 600 SY3 150 F SHP /8-9 UN SY4 600 SY4 285 SY5 400 F SHP UN SY7 600 SY4 150 SY5 285 F SHP /8-8 UN SY7 600 SY5 150 SY7 400 F SHP /8-8 UN SY8 600 SY7 150 SY8 285 F SHP /4-8 UN SY9 400 SY SY7 150 SY8 285 F SHP /4-8 UN SY9 400 SY SY8 150 F SHP /4-8 UN SY SY F SHP /2-8 UN SY imensions 102 imension does not include flange gaskets. (2 required per valve) pplication Notes 1. Valves are rated at 725 psi differential pressure in the closed 100 F media temperature. 2. Valves are furnished with lugs tapped for use between NSI lass 250/300 flanges conforming to NSI 16.5 Standards way assemblies are furnished assembled, calibrated and tested, ready for installation. 4. imension allows for actuator(s) removal without the need to remove the valve from the pipe. 5. Weather shields are available, dimensional data furnished upon request. 6. ual actuated valves have actuators mounted on a single common shaft. 7. Flange gaskets (2 required, not provided with valve) MUST be used between valve and NSI flange. 8. Flange bolts are not included with the valve. These are furnished by others. Fail Safe Non-Fail Safe H 26

27 F7 NSI lass 300 Reinforced Teflon Seat, 316 Stainless isc ubble tight shut-off to NSI lass 300 Standards Long stem design allows for 2 insulation minimum Valve Face-to-face dimensions comply with PI 609 & MSS-SP-68 esigned to be installed between SME/NSI 16.5 Flanges ompletely assembled and tested, ready for installation Tees comply with SME/NSI 16.5 lass 250/300 Flanges pplication These valves are designed to meet the needs of HV and ommercial applications requiring positive shut-off for liquids at higher pressures and temperatures. Typical applications include chiller isolation, cooling tower isolation, change-over systems, large air handler coil control, bypass and process control applications. The large v values provide for an economical control valve solution for larger flow applications. Technical ata Media service chilled, hot water, 60% glycol, steam to 50 psi Valve service double dead end service Flow characteristic modified linear, unidirectional Recommended install SUS (Seat Up Stream) ction quarter turn, mechanically limited Sizes 2" to 24" Type of end fitting for use with SME/NSI 16.5 flanges Materials ody isc Seat Shaft Gland seal ushings carbon steel full lug 316 stainless steel RPTFE 17-4 PH stainless PTFE glass backed PTFE Media temperature range NSI lass 300 limitations Operation ambient temperature range -22 F to 122 F [-30 to 50 ] ody pressure rating SME/NSI lass 300 limitations lose-off pressure NSI lass 300 to F Rangeability 10:1 (for 30 deg to 70 deg range) Maximum velocity 32 FPS Valve Nominal Size Type Suitable ctuators v v IN NSI way Spring Non-Spring F SHP ½ F SHP F SHP F SHP F SHP F SHP F SHP F SHP F SHP F SHP F SHP F SHP F SHP F SHP MO ON/OFF Valve Size v F SHP F SHP F SHP F SHP F SHP F SHP F SHP F SHP F SHP F SHP F SHP F SHP F SHP F SHP F Series GM Series SY Series 27

28 F7 NSI lass 300 Reinforced Teflon Seat, 316 Stainless isc Maximum imensions (Inches) Valve Size v 90 (Max) H No. of Holes Lug olt ctuator lose-off (PSI) F SHP /8-11 UN 285 F SHP /4-10 UN 285 2*GM(X) F SHP /4-10 UN 285 F SHP /4-10 UN 150 F SHP /8-11 UN SY2 400 SY3 600 F SHP /4-10 UN SY2 400 SY3 600 F SHP /4-10 UN SY2 400 SY3 600 F SHP /4-10 UN SY2 285 SY3 600 F SHP /4-10 UN SY3 285 SY4 600 F SHP /4-10 UN SY3 285 SY4 600 SY4 400 F SHP /8-9 UN SY5 600 SY4 150 SY5 285 F SHP UN SY7 600 SY5 150 SY7 400 F SHP /8-8 UN SY8 600 SY7 150 SY8 400 F SHP /8-8 UN SY SY7 150 SY9 285 F SHP /4-8 UN SY SY SY8 150 F SHP /4-8 UN SY SY F SHP /4-8 UN SY9 150 SY F SHP /2-8 UN SY imensions 101 imensions, and do not include flange gaskets. (3 required per valve) pplication Notes 1. Valves are rated at 725 psi differential pressure in the closed 100 F media temperature. 2. Valves are furnished with lugs tapped for use between NSI lass 250/300 flanges conforming to NSI 16.5 Standards way assemblies are furnished assembled with Tee, calibrated and tested, ready for installation. ll 3 way assemblies require the customer to specify the 3-way configuration code prior to order entry to guarantee correct placement of valves and actuator(s) on the assembly. 4. imension allows for actuator(s) removal without the need to remove the valve from the pipe. 5. Weather shields are available, dimensional data furnished upon request. 6. ual actuated valves have single actuators mounted on each valve shaft. 7. Flange gaskets (3 required, not provided with valve) MUST be used between valve and NSI flange. 8. Flange bolts are not included with the valve. These are furnished by others. Non-Fail Safe Note: For tee configuration, please refer to page 5. 28

29 F6 H utterfly Valves 2 30 uctile Iron Lug ody Resilient Seat, 304 Stainless isc with Manual Handle or Gear Wheel Operator 200 psi (2 to 12 ) and 150 psi (14-30 ) bubble tight shut-off Long stem design allows for 2 insulation Valve face-to-face dimensions comply with PI 609 & MSS-SP-67 ompletely assembled and tested, ready for installation pplication These valves are designed to meet the needs of HV and commercial applications requiring bubble tight shut-off for liquids. Typical applications include chiller isolation, cooling tower isolation, change-over systems, large air handler coil control, bypass and process control applications. esigned for use in Victaulic piping systems when mated to Victaulic 41 series flange nipples. Jobsite Note Valves should be stored in a weather protected area prior to construction. omplete installation recommendations can be found in elimo s Installation and Maintenance Instructions for F6/F7 H/HU utterfly Valves. Technical ata Service chilled, hot water, 60% glycol Flow characteristic modified equal percentage ction 90 rotation Sizes 2 to 30 Type of end fitting for use with NSI 125/150 flanges Materials ody ductile iron STM 536 isc 304 stainless steel Seat EPM standard Shaft 416 stainless steel O-ring EPM Upper bushing RPTFE Middle bushings RPTFE Lower bushing RPTFE Handle material mild steel Gear operator materials Housing ductile iron Gears hardened steel Media temperature range -22 F to 250 F [-30 to 120 ] Operation ambient temperature range -22 F to 122 F [-30 to 50 ] ody pressure rating SME/NSI lass 125/150 (200 psi at -30 F to 275 F) lose-off pressure 200 psi (2-12 ), 150 psi (14-30 ) Rangeability 10:1 (for 30 to 70 range) Maximum velocity 12 FPS Valve Nominal Size Type Manual Operators v v IN N [mm] 2-way F650H ½ 65 F665H F680H F6100H F6125H F6150H F6200H F6250H F6300H F6350H F6400H F6450H F6500H F6600H F6750H Valve Size v F650H F665H 2-1/ F680H F6100H F6125H F6150H F6200H F6250H F6300H F6350H F6400H F6450H F6500H F6600H F6750H Handle Gear Wheel OP 29

30 F6 H utterfly Valves 2 30 uctile Iron Lug ody Resilient Seat, 304 Stainless isc with Manual Handle or Gear Wheel Operator Maximum imensions (Inches) Valve Size v 90 v 60 E H No. of Holes Lug olt Operator lose-off (PSI) Wt. lbs (kg) F650H n/a n/a /8-11UN HN [5.1] F665H 2½ n/a n/a /8-11UN HN [6.0] F680H n/a n/a 6 4 5/8-11UN HN [6.1] F6100H n/a n/a /8-11UN HN [8.7] F6125H n/a n/a /4-10UN HN [11.0] F6150H n/a n/a /4-10UN HN [13.2] F6200H n/a n/a /4-10UN HN [19.7] Valve Size v 90 v 60 E H No. of Holes Lug olt Operator lose-off (PSI) Wt. lbs (kg) F650H /8-11UN GW [8.6] F665H 2½ /8-11UN GW [9.5] F680H /8-11UN GW [9.5] F6100H /8-11UN GW [12.2] F6125H /4-10UN GW [14.5] F6150H /4-10UN GW [16.7] F6200H /4-10UN GW [26.3] F6250H /8-9UN GW [37.6] F6300H /8-9UN GW [59.0] F6350H UN GW [81.4] F6400H UN GW [122.4] F6450H /8-7UN GW [142.4] F6500H /8-7UN GW [216.5] F6600H /4-7UN GW [329.0] F6750H /4-7UN GW [568.1] imensions Manual Handle imensions Gear Wheel.H. imension is compressed, add for relaxed state. elimovalve_handle_assymodel E.H. elimovalve_handle_assymodel pplication Notes 1. Valves are rated at 200 psi differential pressure in the closed position (SY psi 14 +). 2. Valves are furnished with lugs tapped for use with NSI lass 125/150 flanges. Installation flanges and hardware are not included way assemblies are furnished assembled and tested, ready for installation. 30

31 F6 NSI lass 150 Reinforced PTFE Seat, 316 Stainless isc with Manual Handle or Gear Wheel Operator ubble tight shut-off to NSI lass 150 Standards Long stem design allows for 2 insulation minimum Valve face-to-face dimensions comply with PI 609 & MSS-SP-68 esigned to be installed between SME/NSI 16.5 Flanges ompletely assembled and tested, ready for installation pplication These valves are designed to meet the needs of HV and ommercial applications requiring positive shut-off for liquids at higher pressures and temperatures. Typical applications include chiller isolation, cooling tower isolation, change-over systems, large air handler coil control, bypass and process control applications. Jobsite Note Valves should be stored in a weather protected area prior to construction. omplete installation recommendations can be found in elimo s Installation and Maintenance Instructions for F6/F7 H/HU utterfly Valves. Technical ata Media service chilled, hot water, 60% glycol, steam to 50 psi Valve service double dead end service Flow characteristic modified equal percentage, unidirectional Recommended install SUS (Seat Up Stream) ction quarter turn, mechanically limited Sizes 2" to 24" Type of end fitting for use with SME/NSI 16.5 flanges Materials ody carbon steel full lug isc 316 stainless steel Seat RPTFE Shaft 17-4 PH stainless Gland seal PTFE ushings glass backed PTFE Handle Material ductile iron Gear Operator Materials Housing ductile iron Gears hardened steel Media temperature range NSI lass 150 limitations Operation ambient temperature range -22 F to 122 F [-30 to 50 ] ody pressure rating SME/NSI lass 150 limitations lose-off pressure NSI lass 150 to F Rangeability 10:1 (for 30 deg to 70 deg range) Maximum velocity 32 FPS Valve Nominal Size Type v v IN N [mm] NSI way F SHP ½ 65 F SHP F SHP F SHP F SHP F SHP F SHP F SHP F SHP F SHP F SHP F SHP F SHP F SHP F SHP Manual Operators Valve Size v F SHP F SHP F SHP F SHP F SHP F SHP F SHP F SHP F SHP F SHP F SHP F SHP F SHP F SHP F SHP Handle Gear Wheel OP 31

32 F6 NSI lass 150 Reinforced PTFE Seat, 316 Stainless isc with Manual Handle or Gear Wheel Operator Maximum imensions (Inches) Valve Size v 90 E H No. of Holes Lug olt Operator Wt. lbs (kg) F SHP n/a n/a /8-11 UN HN05 18 [8.2] F SHP n/a n/a /8-11 UN HN05 18 [8.2] F SHP n/a n/a 6 4 5/8-11 UN HN06 20 [9.1] F SHP n/a n/a /8-11 UN HN06 32 [14.5] F SHP n/a n/a /4-10 UN HN07 38 [17.2] F SHP n/a n/a /4-10 UN HN07 46 [20.9] F SHP n/a n/a /4-10 UN HN08 59 [26.8] Valve Size v 90 E H No. of Holes Lug olt Operator Wt. lbs (kg) F SHP /8-11 UN GW10 25 [11.3] F SHP /8-11 UN GW10 25 [11.3] F SHP /8-11 UN GW11 28 [12.7] F SHP /8-11 UN GW11 38 [17.2] F SHP /4-10 UN GW12 48 [21.8] F SHP /4-10 UN GW12 49 [22.2] F SHP /4-10 UN GW13 58 [26.3] F SHP /8-9 UN GW [50.8] F SHP /8-9 UN GW [73.9] F SHP UN GW [97.5] F SHP UN GW [129.3] F SHP /8-8 UN GW [161.0] F SHP /8-8 UN GW [226.8] F SHP /4-8 UN GW [371.9] F SHP /4-8 UN GW [612.3] lose-off (PSI) NSI lass 150 Limitations lose-off (PSI) NSI lass 150 Limitations imensions Manual Handle.H. imension does not include flange gaskets. (2 required per valve) pplication Notes 1. Valves are rated at 285 psi differential pressure in the closed 100 F media temperature. 2. Valves are furnished with lugs tapped for use between NSI lass 125/150 flanges conforming to NSI 16.5 Standards way assemblies are furnished assembled and ready for installation. 4. Flange gaskets (2 required, not provided with valve) MUST be used between valve and NSI flange. 5. Flange bolts are not included with the valve. These are furnished by others. elimouto_handle imensions Gear Wheel E SHP series valves have a preferred flow direction..h. elimo uto_gear PreferredFlowrate 32

33 F6 NSI lass 300 Reinforced PTFE Seat, 316 Stainless isc with Manual Handle or Gear Wheel Operator ubble tight shut-off to NSI lass 300 Standards Long stem design allows for 2 insulation minimum Valve face-to-face dimensions comply with PI 609 & MSS-SP-68 esigned to be installed between SME/NSI 16.5 Flanges ompletely assembled and tested, ready for installation pplication These valves are designed to meet the needs of HV and ommercial applications requiring positive shut-off for liquids at higher pressures and temperatures. Typical applications include chiller isolation, cooling tower isolation, change-over systems, large air handler coil control, bypass and process control applications. Jobsite Note Valves should be stored in a weather protected area prior to construction. omplete installation recommendations can be found in elimo s Installation and Maintenance Instructions for F6/F7 H/HU utterfly Valves. Technical ata Media service chilled, hot water, 60% glycol, steam to 50 psi Valve service double dead end service Flow characteristic modified equal percentage, unidirectional Recommended install SUS (Seat Up Stream) ction quarter turn, mechanically limited Sizes 2" to 24" Type of end fitting for use with SME/NSI 16.5 flanges Materials ody carbon steel full lug isc 316 stainless steel Seat RPTFE Shaft 17-4 PH stainless Gland seal PTFE ushings glass backed PTFE Handle Material ductile iron Gear Operator Materials Housing ductile iron Gears hardened steel Media temperature range NSI lass 300 limitations Operation ambient temperature range -22 F to 122 F [-30 to 50 ] ody pressure rating SME/NSI lass 300 limitations lose-off pressure NSI lass 300 to F Rangeability 10:1 (for 30 deg to 70 deg range) Maximum velocity 32 FPS Valve Nominal Size Type v v IN N [mm] NSI way F SHP ½ 65 F SHP F SHP F SHP F SHP F SHP F SHP F SHP F SHP F SHP F SHP F SHP F SHP F SHP Manual Operators Valve Size v F SHP F SHP F SHP F SHP F SHP F SHP F SHP F SHP F SHP F SHP F SHP F SHP F SHP F SHP Handle Gear Wheel OP 33

34 F6 NSI lass 300 Reinforced PTFE Seat, 316 Stainless isc with Manual Handle or Gear Wheel Operator Maximum imensions (Inches) Valve Size v 90 E H No. of Holes Lug olt Operator Wt. lbs (kg) lose-off (PSI) F SHP n/a n/a /8-11 UN HN05 15 [6.8] F SHP n/a n/a /4-10 UN HN05 15 [6.8] F SHP n/a n/a 6 8 3/4-10 UN HN06 21 [9.5] F SHP n/a n/a /4-10 UN HN06 29 [13.2] F SHP n/a n/a /4-10 UN HN07 38 [17.2] F SHP n/a n/a /4-10 UN HN07 62 [28.1] Valve Size v 90 E H No. of Holes Lug olt Operator Wt. lbs (kg) lose-off (PSI) F SHP /8-11 UN GW10 23 [10.4] F SHP /4-10 UN GW10 23 [10.4] F SHP /4-10 UN GW11 29 [13.2] F SHP /4-10 UN GW11 35 [15.9] F SHP /4-10 UN GW12 41 [18.6] F SHP /4-10 UN GW13 63 [28.6] F SHP /8-9 UN GW14 93 [42.2] F SHP UN GW [68.0] F SHP /8-8 UN GW [104.3] F SHP /8-8 UN GW [163.3] F SHP /4-8 UN GW [197.3] F SHP /4-8 UN GW [276.7] F SHP /4-8 UN GW [415.0] F SHP /2-8 UN GW [544.3] NSI lass 300 Limitations NSI lass 300 Limitations imensions Manual Handle imensions Gear Wheel.H. imension does not include flange gaskets. (2 required per valve) pplication Notes 1. Valves are rated at 725 psi differential pressure in the closed 100 F media temperature. 2. Valves are furnished with lugs tapped for use between NSI lass 250/300 flanges conforming to NSI 16.5 Standards way assemblies are furnished assembled and ready for installation. 4. Flange gaskets (2 required, not provided with valve) MUST be used between valve and NSI flange. 5. Flange bolts are not included with the valve. These are furnished by others. elimouto_handle E SHP series valves have a preferred flow direction..h. elimo uto-gear PreferredFlowrate 34

35 Features / enefits utterfly Valves SY Series ctuators elimo s SY series electric actuators have been designed to mate with our H(U) and SHP series butterfly valves and other quarter turn valve applications. The patented gear drive mechanism provides for efficient, smooth operation while allowing easy manual override at any time. rawing upon years of experience in the actuation industry, we have incorporated the most desirable features into the SY product range. ll units have NEM 4X ratings, easily visible position indicators, international standard ISO5211 mounting systems, internal thermal motor overload protection, heater, dual auxiliary Form switches, and easily accessible wiring termination points. Wiring diagrams, included in all printed documentation, are also affixed to the outside of the housing on the permanently attached product label. The units are easily visible in mechanical rooms with their characteristic elimo Orange color. Torque ranges are available from 310 to 31,150 in lbs. omed Position Indicator ast luminum over Powder oated NEM 4X Rated Housing Four over Screws for Easy ccess Easily ccessible Field Wiring Terminal Positive Locking Switch ams ISO 5211Mounting System Thermally Protected rive Motor Simple, Single Handed Override Wheel (SY2~12) earing Seals Hardened Steel Gear Sets 35

36 SY 24 Series Non-Spring Return ctuator Technical ata - 24 V pplication: The SY actuators are NEM 4X rated and designed to meet the needs of HV and ommercial applications. Offered on elimo standard and high performance valve series, these actuators are available for on/off and modulating applications. epending on the application, they are available in 24 V/ V, 120 V and 230 V. Technical ata Electrical connection Overload protection Motor protection Gear train Operating range Sensitivity Reversal hysteresis Feedback ngle of rotation 90 irection of rotation Position indication Internal humidity control uxiliary switches mbient temperature ½ conduit connector, screw terminals thermally protected 135 cut-out H lass insulation (SY-1), F lass (SY-2 5) high alloy steel gear sets, self locking (SY -24) on/off, floating point (SY...24MFT) 2-10 V, 4-20m, 0-10 V (SY 24MFT) 0.4m/200mV (SY 24MFT)1.0m/500mV (SY 24MFT) 2-10 V reversible Humidity range up to 95% Housing type Housing material gency listings top mounted domed indicator resistive heating element (2) SPT, V factory set for 5 and 85 change of state -22 F to +150 F [-30 to +65 ] IP67, NEM 4X die cast aluminum alloy ISO, E, csus Power Supply 24 V/V 50/60Hz, single phase Power uty ycle Model Torque Speed onsumption On/Off MFT Override Weight SY1-24(P) 35Nm/310 in-lbs 15s % 75% 8mm Wrench 2.0kg/4.9 lb. SY2-24(MFT) 90Nm/801 in-lbs 15s % 75% Hand Wheel 11kg/24.5 lb. SY3-24(MFT) 150Nm/1335 in-lbs 22s % 75% Hand Wheel 11kg/24.5 lb. SY4-24(MFT) 400Nm/3560 in-lbs 16s % 75% Hand Wheel 22kg/48.5 lb. SY5-24(MFT) 500Nm/4450 in-lbs 22s % 75% Hand Wheel 22kg/48.5 lb. 36

37 SY 120 Series Non-Spring Return ctuator Technical ata V pplication: The SY actuators are NEM 4X rated and designed to meet the needs of HV and ommercial applications. Offered on elimo standard and high performance valve series, these actuators are available for on/off and modulating applications. epending on the application, they are available in 24 V/ V, 120 V and 230 V. Technical ata Electrical connection Overload protection Motor protection Gear train Operating range Sensitivity Reversal hysteresis Feedback ngle of rotation 90 irection of rotation Position indication Internal humidity control uxiliary switches mbient temperature ½ conduit connector, screw terminals thermally protected 135 cut-out H lass insulation (SY-1), F lass (SY-2 12) high alloy steel gear sets, self locking (SY -110) on/off, floating point (SY...120MFT) 2-10 V, 4-20m, 0-10 V (SY 120MFT) 0.4m/200mV (SY 120MFT) 1.0m/500mV (SY 120MFT) 2-10 V reversible Humidity range up to 95% Housing type Housing material gency listings Power Supply Model top mounted domed indicator resistive heating element (2) SPT, V factory set for 5 and 85 change of state -22 F to +150 F [-30 to +65 ] IP67, NEM 4X die cast aluminum alloy ISO, E, csus 120 V 50/60Hz, single phase Torque Speed 60Hz Speed 50Hz Power onsumption On/Off uty ycle Proportional Override SY1-110(P) 35Nm/310 in-lbs 12s 13s % 75% 8mm Wrench 2.0kg/4.9 lb. SY2-120(MFT) 90Nm/801 in-lbs 15s 17s % 75% Hand Wheel 11kg/24.5 lb. SY3-120(MFT) 150Nm/1335 in-lbs 22s 26s % 75% Hand Wheel 11kg/24.5 lb. SY4-120(MFT) 400Nm/3560 in-lbs 16s 18s % 75% Hand Wheel 22kg/48.5 lb. SY5-120(MFT) 500Nm/4450 in-lbs 22s 25s % 75% Hand Wheel 22kg/48.5 lb. SY6-120(MFT) 650Nm/5785 in-lbs 28s 31s % 75% Hand Wheel 22kg/48.5 lb. SY7-120(MFT) 1000Nm/8900 in-lbs 46s 55s % 75% Hand Wheel 36kg/79.5 lb. SY8-120(MFT) 1500Nm/13350 in-lbs 46s 55s % 75% Hand Wheel 36kg/79.5 lb. SY9-120(MFT) 2000Nm/17800 in-lbs 58s 70s % 50% Hand Wheel 56kg/123.5 lb. SY10-120(MFT) 2500Nm/22250 in-lbs 58s 70s % 50% Hand Wheel 56kg/123.5 lb. SY11-120(MFT) 3000Nm/26700 in-lbs 58s 70s % 50% Hand Wheel 56kg/123.5 lb. SY12-120(MFT) 3500Nm/31150 in-lbs 58s 70s % 50% Hand Wheel 56kg/123.5 lb. Weight 37

38 SY 230 Series Non-Spring Return ctuator Technical ata V pplication: The SY actuators are NEM 4X rated and designed to meet the needs of HV and ommercial applications. Offered on elimo standard and high performance valve series, these actuators are available for on/off and modulating applications. epending on the application, they are available in 24 V/ V, 120 V and 230 V. Technical ata Electrical connection Overload protection Motor protection Gear train Operating range Sensitivity Reversal hysteresis Feedback ngle of rotation 90 irection of rotation Position indication Internal humidity control uxiliary switches mbient temperature ½ conduit connector, screw terminals thermally protected 135 cut-out H lass insulation (SY-1), F lass (SY-2 12) high alloy steel gear sets, self locking (SY -220) on/off, floating point (SY...230MFT) 2-10 V, 4-20m, 0-10 V (SY 230MFT) 0.4m/200mV (SY 230MFT) 1.0m/500mV (SY 230MFT) 2-10 V reversible Humidity range up to 95% Housing type Housing material gency listings top mounted domed indicator resistive heating element (2) SPT, V factory set for 5 and 85 change of state -22 F to +150 F [-30 to +65 ] IP67, NEM 4X die cast aluminum a lloy ISO, E, csus Power Supply 230 V 50/60Hz, single phase Speed Speed Power uty ycle Model Torque 60Hz 50Hz onsumption On/Off MFT Override Weight SY1-220(P) 35Nm/310 in-lbs 12s 13s % 75% 8mm Wrench 2.0kg/4.9 lb. SY2-230(MFT) 90Nm/801 in-lbs 15s 17s % 75% Hand Wheel 11kg/24.5 lb. SY3-230(MFT) 150Nm/1335 in-lbs 22s 26s % 75% Hand Wheel 11kg/24.5 lb. SY4-230(MFT) 400Nm/3560 in-lbs 16s 18s % 75% Hand Wheel 22kg/48.5 lb. SY5-230(MFT) 500Nm/4450 in-lbs 22s 25s % 75% Hand Wheel 22kg/48.5 lb. SY6-230(MFT) 650Nm/5785 in-lbs 28s 31s % 75% Hand Wheel 22kg/48.5 lb. SY7-230(MFT) 1000Nm/8900 in-lbs 46s 55s % 75% Hand Wheel 36kg/79.5 lb. SY8-230(MFT) 1500Nm/13350 in-lbs 46s 55s % 75% Hand Wheel 36kg/79.5 lb. SY9-230(MFT) 2000Nm/17800 in-lbs 58s 70s % 50% Hand Wheel 56kg/123.5 lb. SY10-230(MFT) 2500Nm/22250 in-lbs 58s 70s % 50% Hand Wheel 56kg/123.5 lb. SY11-230(MFT) 3000Nm/26700 in-lbs 58s 70s % 50% Hand Wheel 56kg/123.5 lb. SY12-230(MFT) 3500Nm/31150 in-lbs 58s 70s % 50% Hand Wheel 56kg/123.5 lb. 38

39 SY Series Non-Spring ctuator imensions SY-2~6... SY-1... SY-9~12... SY-7~8... MOEL IM (MX) dd to im for cover removal IM IM (MX) IM Inches [mm] Inches [mm] Inches [mm] Inches [mm] Inches [mm] SY [155] 3.94 [100] 4.25 [108] 8mm - SY2~ [255] 7.48 [190] 7.87 [200] [330] 7.87 [200] SY4~ [315] 8.86 [225] 9.21 [234] [380] [300] SY7~ [420] 8.86 [225] 9.21 [234] [450] [340] SY9~ [590] 8.86 [225] [260] [470] [350] Note: ~ indicates range of actuator i.e., SY2~3 = SY-2 and SY-3 39

40 Wire Size vs. Length of Run for SY Series ctuators SY1 SY2 SY3 SY4 SY5 mps mps mps mps mps wire gauge MX istance between ctuator and Supply (feet) V SY1 SY2 SY3 SY4 SY5 SY6 SY7 SY8 SY9 SY10 SY11 SY12 mps mps mps mps mps mps mps mps mps mps mps mps wire gauge MX istance between ctuator and Supply (feet) V SY1 SY2 SY3 SY4 SY5 SY6 SY7 SY8 SY9 SY10 SY11 SY12 mps mps mps mps mps mps mps mps mps mps mps mps wire gauge MX istance between ctuator and Supply (feet) V The NE mandates that 24 V over 100 V power requires LSS 1 wiring conduit. Local codes may vary. o NOT mix LSS 1 & LSS 2 circuits in the same conduit. Generally, 24 V actuators over 100 V should be changed to 120 V models. 40

41 Interface Wiring etail SYx-MFT, 24V, 120/230V ctuators: SYx-MFT INSTLLTION NOTES UTION Notes: 1. Motor MS have been factory calibrated and should not be moved. 2. n adaption must be performed if any limit switch is adjusted. This will calibrate the beginning and end stopping points. Press the adaption button for 3 seconds and release. P Tool Service Jack onnection ontrol Signal + ontrol Signal - FK + FK - Power Supply om - Power Supply Hot + daption ontrol Signal + ontrol Signal - FK + FK - 24V irection of Rotation N - Power Supply ommon H - Power Supply Hot P Tool Service Jack daption irection of Rotation 120/230V 41

42 SYx-P Interface Wiring etail Open LE losed LE Sensitivity VR2 VR1 ip Switch N Supply H - SIG + IN - F + OUT Sensitivity switchsetting is position #3 for factory default. To widen deadband, select a higher number (up to 9). INSTLLTION NOTES UTION Notes: 1. pplicable to the SY1 and legacy SY2-12 actuators. 2. o not change sensitivity or dip switch settings with power applied! 3. VR1 and VR2 are factory calibrated and should not be moved. 4. Motor MS have been factory calibrated and should not be moved. ip Switch Settings OFF ON INPUT = 2-10 V OFF ON RESPONSE = IRET OFF INPUT = 4-20m OFF RESPONSE = REVERSE ON ON WRNING Potentiometer (Factory Pre-set) OFF ON OFF ON OFF ON INPUT = 1-5 V OUTPUT = 4-20m OUTPUT = 2-10 V For 2-position actuators with 1k feedback option Potentiometer points 1, 2, 3 are wired to terminal blocks 8, 9, 10. When a valve is closed: 8, 9 1k Ω 9, 10 0k Ω When a valve is opened: 8, 9 0k Ω 9, 10 1k Ω OFF ON OFF ON OFF ON LOSS OF SIGNL = LOSE (irect cting) LOSS OF SIGNL = (Reverse cting) LOSS OF SIGNL = (irect cting) LOSS OF SIGNL = LOSE (Reverse cting) LOSS OF SIGNL = STOP *On modulating actuators O NOT master/slave using optional potentiometer. For modulating actuators with 1k feedback option* Potentiometer points 1, 2, 3 are wired to terminal blocks 8, 9, 10. When a valve is closed: 8, 9 1k Ω 9, 10 0k Ω When a valve is opened: 8, 9 0k Ω 9, 10 1k Ω 42

43 SY Series Non-Spring ctuators UTION Electrical Travel djustment (Factory Pre-set) SY-1 Factory pre-set see chart below. Field adjustable if required LS4 uxiliary Switch for losed Indication LS4 LS3 LS2 LS1 LS3 uxiliary Switch for Opened Indication Factory pre-set and calibrated. o not adjust - warranty voided LS2 LOSE lockwise ecrease losed ngle ounter-clockwise Increase losed ngle LS1 lockwise Increase Opening ngle ounter-clockwise ecrease Opening ngle UTION Electrical Travel djustment SY-2-12 Factory pre-set see chart below. Field adjustable if required LS4 uxiliary Switch for losed Indication LS3 uxiliary Switch for Opened Indication LS4 WRNING F E LS4 LS3 LS3 LS2 LS1 Factory pre-set and calibrated. o not adjust - warranty voided LS2 LOSE LS1 Switches at left are shown with actuator fully open LS LS4 - F - E lockwise ecrease losed ngle ounter-clockwise Increase losed ngle lockwise Increase Opening ngle ounter-clockwise ecrease Opening ngle INSTLLTION NOTES UTION Notes: 1. n adaption must be performed when the limit switches are adjusted. For the SYx-MFT actuators. This will calibrate the beginning and end stopping points. Press the adaption button for 3 seconds and release. 43

44 Wiring for amper ctuators and ontrol Valves On/Off, 24V, 120/230V ctuators: SY1-24 SY1-110 SY SY W546 Hazard Identification Warnings and autions appear at appropriate sections throughout this manual. Read these carefully. UTION Indicates a potentially hazardous situation which, if not avoided, may result in minor or moderate injury. It may also be used to alert against unsafe practices. Indicates an action or condition that may cause irreversible damage to the actuator(s) or associated equipment. Equipment damage! Power consumption and input impedance must be observed. NOTES SY Each actuator should be powered by a single, isolated 33 control transformer. Isolation relays must be used in parallel connection of multiple actuators using a common control signal input. "H" cannot be connected to terminal #3 and #4 simultaneously. Required: Terminal #7 needs to be field wired to enable heater circuit. INSTLLTION NOTES Observe class 1 and class 2 wiring restrictions. Transformer sizing = SY actuator draw X 1.25 (safety margin) (Ex. SY2-24 requires 3.0 x 1.25 = 3.75, 3.75 X 24 V = 90V Transformer). NOTES SY (220) aution: Power Supply Voltage Isolation relays must be used in parallel connection of multiple actuators using a common control signal input. "H" (L2) cannot be connected to terminal #3 and #4 simultaneously. Required: Terminal #7 needs to be field wired to enable heater circuit V Transformer G G Ground 120 and 230 V G G Ground Line Volts LS3 Open lose LS3 1 ommon 3 Open 4 losed onnect to #1 for fully 5 open indication 6 onnect to #1 for fully closed indication 7 HTR E F LS3 - (Open Indication) LS4 -F (losed Indication) ontact Rating: V Max. SY N L1 H L2 Open lose 1 ommon 3 Open 4 losed onnect to #1 for fully 5 open indication 6 onnect to #1 for fully closed indication 7 HTR E F LS3 - (Open Indication) LS4 -F (losed Indication) ontact Rating: V Max. SY (220) E - (Open Indication) ontact Rating: V Max V Max. LS4 E - (Open Indication) ontact Rating: V Max V Max. LS4 F -E (losed Indication) F -E (losed Indication) SY1-24 SY1-110 (220) SY1 ontact rrangements 44

45 Wiring for amper ctuators and ontrol Valves Proportional, 24V, 120/230V ctuators: SY1-24P SY1-110P SY1-220P W547 Hazard Identification Warnings and autions appear at appropriate sections throughout this manual. Read these carefully. UTION Indicates a potentially hazardous situation which, if not avoided, may result in minor or moderate injury. It may also be used to alert against unsafe practices. Indicates an action or condition that may cause irreversible damage to the actuator(s) or associated equipment. Equipment damage! Power consumption and input impedance must be observed. INSTLLTION NOTES Observe lass 1 and lass 2 wiring restrictions. Transformer sizing = SY actuator draw X 1.25 (safety margin) (Ex. SY2-24 requires 3.0 x 1.25 = 3.75, 3.75 X 24 V = 90V Transformer) PPLITION NOTES Ground shielded wire at control panel chassis. Tape back ground at actuator. Use of feedback is optional. NOTES SY1 24P Each actuator should be powered by a single, isolated 33 control transformer. Power supply om/neutral and ontrol Signal " " wiring to a common is prohibited. Terminals 4 and 6 need to be wired separately. o not change sensitivity or dip switch settings with power applied. NOTES SY1 110P (220P) aution: Power supply voltage. Power supply om/neutral and ontrol Signal " " wiring to a common is prohibited. Terminals 4 and 6 need to be wired separately. o not change sensitivity or dip switch settings with power applied V Transformer G G Ground 120 and 230 V G G Ground Line Volts 4 Power Supply om 5 Power Supply Hot N L1 H L2 4 Power Supply om 5 Power Supply Hot ontrol signal Feedback ontrol Signal (-) 7 ontrol Signal (+) 8 Internal Use Only 9 Internal Use Only 10 Internal Use Only 11 Feedback (-) 12 Feedback (+) E F LS3 - (Open Indication) ontact Rating: V Max V Max. LS4 -E (losed Indication) SY1-24P ontrol signal Feedback ontrol Signal (-) 7 ontrol Signal (+) 8 Internal Use Only 9 Internal Use Only 10 Internal Use Only 11 Feedback (-) 12 Feedback (+) E F LS3 - (Open Indication) ontact Rating: V Max V Max. LS4 -E (losed Indication) SY1-110P (220P) 45

46 Wiring for amper ctuators and ontrol Valves Proportional, 24V, 120/230V ctuators: SY MFT SY MFT SY MFT Hazard Identification Warnings and autions appear at appropriate sections throughout this manual. Read these carefully. UTION Indicates a potentially hazardous situation which, if not avoided, may result in minor or moderate injury. It may also be used to alert against unsafe practices. Indicates an action or condition that may cause irreversible damage to the actuator(s) or associated equipment. Equipment damage! Power consumption and input impedance must be observed. INSTLLTION NOTES Observe lass 1 and lass 2 wiring restrictions. Transformer sizing = SY actuator draw X 1.25 (safety margin) (Ex. SY2-24 requires 3.0 x 1.25 = 3.75, 3.75 X 24 V = 90V Transformer) PPLITION NOTES Ground shielded wire at control panel chassis. Tape back ground at actuator. Use of feedback is optional. W547-2 W549 NOTES SY MFT Each actuator should be powered by a single, isolated 33 control transformer. Power supply om/neutral and ontrol Signal " " wiring to a common is prohibited. NOTES SY MFT (230MFT) aution: Power supply voltage. Internal Use Only Internal Use Only P Tool Service Jack 1 Internal Use Only 2 Internal Use Only 3 Internal Use Only ontrol Signal Feedback ontrol Signal (+) ontrol Signal (-) Feedback Signal (+) Y 1 U5 ddress /- ~/+ Power Supply om Power Supply Hot 24V Feedback Signal (-) Not Used daption 8 9 Internal Use Only Internal Use Only E ontrol Signal Feedback 36 LS3 - (Open Indication) ontact Rating: V Max V Max. LS4 G G 34 Not Used - PE ontrol Signal (+) ontrol Signal (-) Feedback Signal (+) Feedback Signal (-) Not Used - Not Used - PE Y 1 U P Tool Service Jack Y2 Y1 daption SYx-120MFT SYx-230MFT SYx-24MFT 10 Internal Use Only Power Supply om 120v (N) / 230v (L1) Power Supply Hot 120v (H) / 230v (L2) Internal Use Only N L Internal Use Only 1 Internal Use Only 2 Internal Use Only 3 Internal Use Only ddress 8 Internal Use Only Y1 9 Internal Use Only Y2 10 Internal Use Only F -E (losed Indication) SY MFT SY MFT (230MFT) 46

47 Wiring for amper ctuators and ontrol Valves On/Off, 24V, 110/120/230V ctuators: SY SY SY Hazard Identification Warnings and autions appear at appropriate sections throughout this manual. Read these carefully. UTION Indicates a potentially hazardous situation which, if not avoided, may result in minor or moderate injury. It may also be used to alert against unsafe practices. Indicates an action or condition that may cause irreversible damage to the actuator(s) or associated equipment. Equipment damage! Power consumption and input impedance must be observed. INSTLLTION NOTES Observe class 1 and class 2 wiring restrictions. Transformer sizing = SY actuator draw X 1.25 (safety margin) (Ex. SY2-24 requires 3.0 x 1.25 = 3.75, 3.75 X 24 V = 90V Transformer). NOTES aution: Power Supply Voltage. Isolation relays must be used in parallel connection of multiple actuators using a common control signal input. "H" (L2) cannot be connected to terminal #3 and #4 simultaneously. Required: Terminal #7 needs to be field wired to enable heater circuit. 24 V Transformer G G Ground ctuator 120 and 230 V G G Ground ctuator Line Volts Open lose K1 K1-1 ommon 3 Open 4 losed HTR N L1 H L2 Open lose K1 K1-1 ommon 3 Open 4 losed HTR LS3 LS3 G K1- E F G LS3 - (Open Indication) LS4 -F (losed Indication) ontact Rating: V Max. SY ctuator Ground 1 ommon 3 Open 4 losed HTR LS3 - (Open Indication) LS4 E -F (losed Indication) F ontact Rating: V Max. SY K1- G LS3 - (Open Indication) LS4 E -F (losed Indication) F ontact Rating: V Max. SY (220) G Ground ctuator 1 ommon 3 Open 4 losed HTR LS3 - (Open Indication) LS4 E -F (losed Indication) F ontact Rating: V Max. SY (220) E - (Open Indication) ontact Rating: V Max V Max. LS4 E - (Open Indication) ontact Rating: V Max V Max. LS4 F -E (losed Indication) F -E (losed Indication) SY1-24 SY1-110 (220) SY1 ontact rrangements 47

48 Wiring for ontrol Valves Proportional, 24V ctuators: SY1-24P W550 Hazard Identification 33 Warnings and autions appear at appropriate sections throughout this manual. Read these carefully. UTION Indicates a potentially hazardous situation which, if not avoided, may result in minor or moderate injury. It may also be used to alert against unsafe practices. Indicates an action or condition that may cause irreversible damage to the actuator(s) or associated equipment. Equipment damage! Power consumption and input impedance must be observed. INSTLLTION NOTES Observe class 1 and class 2 wiring restrictions. 24 V Transformer Line Volts G 35 Feedback () 36 G Ground ctuator 4 Power Supply om 5 Power Supply Hot 6 ontrol Signal (-) 7 ontrol Signal (+) 8 Internal Use Only 9 Internal Use Only 10 Internal Use Only 11 Feedback (-) 12 Feedback (+) E F LS3 - (Open Indication) ontact Rating: V Max V Max. LS4 -E (losed Indication) SY1-24P Transformer sizing = SY actuator draw X 1.25 (safety margin) (Ex. SY2-24 requires 3.0 x 1.25 = 3.75, 3.75 X 24 V = 90V Transformer) V Transformer G G Ground ctuator NOTES SY1-24P Each actuator should be powered by a single, isolated 33 control transformer. SY1-24P notes: Power supply om/neutral and ontrol Signal " " wiring to a common is prohibited. Terminals 4 and 6 need to be wired separately otherwise irreversible damage will occur. o not change sensitivity or dip switch settings with power applied PPLITION NOTES Recommended twisted shielded pair for control wiring. Ground shielded wire at control panel chassis. Tape back ground at actuator. Use of feedback is optional. Line Volts ontrol Signal 35 Feedback () 36 4 Power Supply om 5 Power Supply Hot 6 ontrol Signal (-) 7 ontrol Signal (+) 8 Internal Use Only 9 Internal Use Only 10 Internal Use Only 11 Feedback (-) 12 Feedback (+) E F LS3 - (Open Indication) ontact Rating: V Max V Max. LS4 -E (losed Indication) SY1-24P 48

49 Wiring for ontrol Valves Proportional, Multiple Wiring, 24V ctuators: SY MFT W550-2 Hazard Identification Warnings and autions appear at appropriate sections throughout this manual. Read these carefully. UTION Indicates a potentially hazardous situation which, if not avoided, may result in minor or moderate injury. It may also be used to alert against unsafe practices. INSTLLTION NOTES Observe class 1 and class 2 wiring restrictions. Transformer sizing = SY actuator draw X 1.25 (safety margin) (Ex. SY2-24 requires 3.0 x 1.25 = 3.75, 3.75 X 24 V = 90V Transformer). Indicates an action or condition that may cause irreversible damage to the actuator(s) or associated equipment. Equipment damage! Power consumption and input impedance must be observed NOTES SY MFT Each actuator should be powered by a single, isolated control transformer. PPLITION NOTES Recommended twisted shielded pair for control wiring. Ground shielded wire at control panel chassis. Tape back ground at actuator. 36 Use of feedback is optional. ctuator Internal Use Only P Tool Service Jack 1 Internal Use Only Internal Use Only 2 3 Internal Use Only Internal Use Only ontrol Signal (+) ontrol Signal (-) Y 1 /- ~/+ Power Supply om Power Supply Hot 24V ontrol Signal LS3 - (Open Indication) Feedback 36 Feedback G 35 Feedback Signal (+) Feedback Signal (-) Not Used - Not Used - PE ontrol Signal (+) ontrol Signal (-) Feedback Signal (+) Feedback Signal (-) Not Used - Not Used - U ctuator Y 1 U ddress daption Y1 Y2 P Tool Service Jack ddress daption Y1 Y2 SYx-24MFT SYx-24MFT /- ~/ Internal Use Only Internal Use Only Internal Use Only Internal Use Only Internal Use Only Internal Use Only Internal Use Only Internal Use Only Power Supply om Power Supply Hot Internal Use Only Internal Use Only Internal Use Only 33 24V 33 E F LS4 -F (losed Indication) ontact Rating: V Max. G PE SY2 5-24MFT 49

50 Wiring for ontrol Valves Proportional, 110/220V, 120/230V ctuators: SY1-110P SY1-220P W552-1 Hazard Identification 120 and 230 V G G Ground Warnings and autions appear at appropriate N L1 4 Power Supply om sections throughout this manual. Read these carefully. H L2 5 Power Supply Hot UTION 6 ontrol Signal (-) Indicates a potentially hazardous situation which, if 7 ontrol Signal (+) not avoided, may result in minor or moderate injury. It may also be used to alert against unsafe practices Internal Use Only 9 Internal Use Only Indicates an action or condition that may cause irreversible damage to the actuator(s) or associated equipment. Equipment damage! Power consumption and input impedance must be observed. INSTLLTION NOTES Observe class 1 and class 2 wiring restrictions. Feedback () Internal Use Only 11 Feedback (-) 12 Feedback (+) E F LS3 ctuator - (Open Indication) ontact Rating: V Max V Max. LS4 -E (losed Indication) SY1-110P (220P) PPLITION NOTES G G Ground ctuator Recommended twisted shielded pair for control wiring. Ground shielded wire at control panel chassis. Tape back ground at actuator. Use of feedback is optional. NOTES SY1-110P (220P) aution: Power supply voltage. o not change sensitivity or dip switch settings with power applied. ontrol Signal 35 Feedback () 36 4 Power Supply om 5 Power Supply Hot 6 ontrol Signal (-) 7 ontrol Signal (+) 8 Internal Use Only 9 Internal Use Only 10 Internal Use Only 11 Feedback (-) 12 Feedback (+) E F LS3 - (Open Indication) ontact Rating: V Max V Max. LS4 -E (losed Indication) SY1-110P (220P) 50

51 Wiring for ontrol Valves Proportional, Multiple Wiring, 120/230V ctuators: SY MFT SY MFT W552-2 Hazard Identification Warnings and autions appear at appropriate sections throughout this manual. Read these carefully. UTION Indicates a potentially hazardous situation which, if not avoided, may result in minor or moderate injury. It may also be used to alert against unsafe practices. Indicates an action or condition that may cause irreversible damage to the actuator(s) or associated equipment. Equipment damage! Power consumption and input impedance must be observed. INSTLLTION NOTES Observe class 1 and class 2 wiring restrictions PPLITION NOTES Recommended twisted shielded pair for control wiring. Ground shielded wire at control panel chassis. Tape back ground at actuator. Use of feedback is optional. NOTES SY MFT (230MFT) aution: Power supply voltage. Power Supply om 120V (N) / 230V (L1) Power Supply Hot 120V (H) / 230V (L2) N L Internal Use Only ontrol Signal (+) Y P Tool Service Jack 1 Internal Use Only Internal Use Only ontrol Signal (-) 1 2 Internal Use Only Feedback 36 Feedback Signal (+) Feedback Signal (-) Not Used - U Internal Use Only E F ontrol Signal LS3 - (Open Indication) LS4 -F (losed Indication) ontact Rating: V Max. Feedback 36 G G Not Used - PE ontrol Signal (+) ontrol Signal (-) Feedback Signal (+) Feedback Signal (-) Not Used - Not Used - PE 2 ctuator Y 1 U ctuator P Tool Service Jack daption SYx-120MFT SYx-230MFT daption SYx-120MFT SYx-230MFT N L ddress 8 Internal Use Only Y1 9 Internal Use Only Y2 10 Internal Use Only Power Supply om 120V (N) / 230V (L1) Power Supply Hot 120V (H) / 230V (L2) Internal Use Only Internal Use Only 1 Internal Use Only 2 Internal Use Only 3 Internal Use Only ddress 8 Internal Use Only Y1 9 Internal Use Only Y2 10 Internal Use Only SY MFT SY MFT 51

52 F ctuators, On/Off imensions with 2-Way Valve F2WUIM_ H Models F24 US F24-S US F120 US F120-S US w/built-in ux. Switches w/built-in ux. Switches Technical ata ontrol on/off Power consumption F24(-S) US running 5 W holding 1.5 W F120(-S) US running 6 W holding 2.3 W Transformer sizing 10 V, class 2 power Electrical connection 3 ft, 18 G appliance cables (-S model has 2 cables) ½ conduit connector Electrical protection 120 V actuators double insulated Overload protection electronic throughout 0 to 95 rotation ngle of rotation 95 Position indication visual indicator Manual override hex crank Running time control 150 sec. independent of load spring < 20 sec. mbient temperature -22 F to 122 F [-30 to 50 ] Housing NEM 2 / IP54 gency listings UL 873, S 22.2 No. 24 certified, E Noise level max. 45 d() F...-S US uxiliary switches 2 x SPT, V, UL listed, one switch is fixed at +5, one is adjustable 25 to 85 (double insulated) imensions (Inches) Fail Safe (psi) Valve Size (Max) H F 2*F F650H F650HU F665H 2½ F665HU 2½ F680H F680HU F6100HU F6125HU F SHP F SHP 2½ F SHP F SHP F SHP F SHP 2½ F SHP F SHP

53 F ctuators, On/Off imensions with 3-Way Valve HS WGP11 to live electrical components could result in death or serious injury. 24 V Transformer Line Volts 1 ommon 2 + Hot 3 W194 F24 US 2 On/Off Wiring W195-UX imensions (Inches) Fail Safe (psi) Valve Size (Max) H F 2*F F750H F750HU F765H 2½ F765HU 2½ F780HU uxiliary Switches Wiring iagrams 2 UTION Equipment damage! ctuators may be connected in parallel. Power consumption must be observed. 3 ctuators may also be powered by 24 V. For end position indication, interlock control, fan startup, etc., F24-S US incorporates two built-in auxiliary switches: 2 x SPT, 7 (2.5) 250 V, UL listed, one switch is fixed at +5, one is adjustable 25 to 85. Meets culus or UL and S requirements without the need of an electrical ground connection. WRNING Live Electrical omponents! uring installation, testing, servicing and troubleshooting of this product, it may be necessary to work with live electrical components. Have a qualified licensed electrician or other individual who has been properly trained in handling live electrical components perform these tasks. Failure to follow all electrical safety precautions when exposed to live electrical components could result in death or serious injury. 53

54 F ctuators, Multi-Function Technology imensions with 2-Way Valve F2WUIM_ Models FX24-MFT-X1 FX24-MFT-S-X1 w/built-in ux. Switches Technical ata Power supply 24 V, +/- 20%, 50/60 Hz 24 V, +20% / -10% Power running 7.5 W consumption holding 3 W Transformer sizing 10 V (lass 2 power source) Electrical connection FX... 3 ft [1m] default, 10 ft [3m] or 16 ft [5m] 18 G appliance or plenum cables, with or without 1/2 conduit connector -S models: two 3 ft [1m] default, 10 ft [3m] or 16 ft [5m] appliance cables with or without 1/2" conduit connectors Overload protection electronic throughout 0 to 95 rotation Operating range Y* 2 to 10 V, 4 to 20 m (default) variable (V, PWM, floating point, on/off) Input impedance 100 kw for 2 to 10 V (0.1 m) 500 W for 4 to 20 m 1500 W for PWM, floating point and on/off control Feedback output U* 2 to 10 V, 0.5 m max Torque minimum 180 in-lb (20 Nm) irection of spring reversible with cw/ccw mounting rotation* motor reversible with built-in switch Mechanical 95 (adjustable with mechanical end stop, 35 to 95 ) angle of rotation* Running time spring <20 -4 F to 122 F [-20 to 50 ]; < F [-30 ] motor* 150 seconds (default), variable (70 to 220 seconds) ngle of Rotation off (default) adaptation Override control* min position = 0% mid. position = 50% max. position = 100% Position indication visual indicator, 0 to 95 (0 is spring return position) Manual override 5 mm hex crank (³ ₁₆" llen), supplied Humidity max. 95% RH, non-condensing mbient temperature -22 to 122 F (-30 to 50 ) Storage temperature -40 to 176 F (-40 to 80 ) Housing NEM 2, IP54, Enclosure Type 2 Housing material zinc coated metal and plastic casing Noise level 40d() 150 seconds, run time dependent 62d() spring return gency listings culus acc. to UL /-2-14, N/S E :02, E acc. to 2004/108/E & 2006/95/E Quality standard ISO 9001 Servicing maintenance free Weight 4.6 lbs. (1.9 kg), 4.9 lbs. (2 kg) with switch * Variable when configured with MFT options Rated Impulse Voltage 800V, Type of action 1. (1.. for -S version), ontrol Pollution egree 3. Programmed for 70 sec motor run time. t 150 sec motor run time, transformer sizing is 8.5 V and power consumption is 6 W running / 3 W holding. FX24-MFT-S-X1 uxiliary switches 2 x SPT V, UL approved one set at +10, one adjustable 10 to 90 H imensions (Inches) Fail Safe (psi) Valve Size (Max) H F 2*F F650H F650HU F665H 2½ F665HU 2½ F680H F680HU F6100HU F6125HU F SHP F SHP 2½ F SHP F SHP F SHP F SHP 2½ F SHP F SHP imensions with 3-Way Valve imensions (Inches) Fail Safe (psi) Valve Size (Max) H F 2*F F750H F750HU F765H 2½ F765HU 2½ F780HU HS WGP11 54

55 F ctuators, Multi-Function Technology Wiring iagrams 3 ctuators may also be powered by 24 V. 4 IN4004 or IN4007 diode (IN4007 supplied, elimo part number 40155). 5 Triac and can also be contact closures. ontrol signal may be pulsed from either the Hot (Source) or 6 ommon (Sink) 24 V line. Position feedback cannot be used with Triac sink controller. 7 The actuators internal common reference is not compatible. The ZG-R W resistor converts the 4 to 20 m control signal to 2 to 10 V, up to 2 actuators may be connected in parallel. Meets culus or UL and S requirements without the need of an electrical ground connection. WRNING Live Electrical omponents! uring installation, testing, servicing and troubleshooting of this product, it may be necessary to work with live electrical components. Have a qualified licensed electrician or other individual who has been properly trained in handling live electrical components perform these tasks. Failure to follow all electrical safety precautions when exposed to live electrical components could result in death or serious injury. V/4-20 m PWM W399_utterfly W399_utterfly Master/Slave Wiring 24 V Transformer Master 5 Master_Slave W399_utterfly Line Volts 3 ontrol Signal 2 to 10 V ( ) (+) lk (1) ommon Red (2) + Hot Wht (3) Y Input, 2 to 10 V Org (5) U Output 2 to 10 V W W Slave 5 lk (1) ommon Red (2) + Hot Wht (3) Y Input, 2 to 10 V Org (5) U W W On/Off control Floating Point control W399_utterfly W600_F_FX Master/Slave F24-MFT-S FX24-MFT-S-X1 FX24-MFT-S uxiliary Switches for FX24-MFT-S-X1 55

56 10 GK24-3-X1 ctuators, On/Off, Floating Point imensions with 2-Way Valve M_GM_LineRevised H Technical ata GK24-3-X1 Power supply 24V ±20% 50/60Hz 24V ±10% Power consumption 12W (3W) Transformer sizing 21V (class 2 power source) Electrical connection 18 G plenum rated cable ½" conduit connector protected NEM 2 (IP54) 3 ft [1m] 10 ft [3m] 16 ft [5m] Overload protection electronic throughout 0 to 95 rotation Operation range Y on/off, floating point Input impedance 100kW (0.1 m), 500W 1500W (floating point, on/off) Feedback output U 2 to 10V, 0.5m max, V variable ngle of rotation max. 95, adjustable with mechanical stop electronically variable irection of rotation reversible with switch Fail-safe position adjustable with dial or tool 0 to 100% in 10% increments Position indication reflective visual indicator (snap-on) Manual override external push button Running time normal operation fail-safe 150 seconds (default), variable 90 to 150 seconds 35 seconds Humidity 5 to 95% RH non-condensing (EN ) mbient temperature -22 F to +122 F [-30 to +50 ] Storage temperature -40 F to +176 F [-40 to +80 ] Housing NEM2, IP54, UL enclosure type 2 Housing material UL94-5V gency list culus acc. to UL /-2-14 N/S E :02 E acc. to 2004/108/EE and 2006/95/E Noise level < 45d() Servicing maintenance free Quality standard ISO 9001 imensions (Inches) Non-Fail Safe (psi) Valve Size (Max) H GK F680H F6100HU F6125HU F SHP F SHP 2½ F SHP F SHP F SHP F SHP 2½ F SHP F SHP imensions with 3-Way Valve imensions (Inches) Non-Fail Safe (psi) Valve Size (Max) H GM F765H 2½ F780HU F SHP F SHP 2½ F SHP F SHP Single_utterfly 0 06/10 - Subject to change. elimo ircontrols (US), Inc. 56

57 GK24-3-X1 ctuators, On/Off, Floating Point Electrical Installation Wiring iagrams Wiring diagram Note onnect via safety isolation transformer.! Parallel connection of other actuators possible. Note performance data for supply. able lengths T ~ T ~ Y U Y U L V V L tot 1 Provide overload protection and disconnect as required. 3 ctuators may also be powered by 24 V Position feedback cannot be used with Triac sink controller. The actuator internal common reference is not compatible. ontrol signal may be pulsed from either the Hot (source) or the ommon (sink) 24 V line. ontact closures & also can be triacs. & should both be closed for triac source and open for triac sink. For triac sink the common connection from the actuator must be connected to the hot connection of the controller. Note When several actuators are connected in parallel, the maximum cable length must be divided by the number of actuators N L 230 V 24 V T Y L 1 U Meets UL requirements without the need of an electrical ground connection. WRNING Live Electrical omponents! uring installation, testing, servicing and troubleshooting of this product, it may be necessary to work with live electrical components. Have a qualified licensed electrician or other individual who has been properly trained in handling live electrical components perform these tasks. Failure to follow all electrical safety precautions when exposed to live electrical components could result in death or serious injury. L 1 Note There are no special restrictions on installation if the supply and data cable are routed separately NOTE: Wiring diagrams shown are for single actuator mounted solutions able colors: 1 = black 2 = red 3 = white 5 = orange = ctuator = ontrol unit L1 = elimo connecting cable, 1 m (4 x 0.75 mm 2 ) L2 = ustomer cable Ltot = Maximum cable length ross section L2 Max. cable length Example for Ltot = L1 + L2 / 0.75 mm 2 <30 m <5 m 1 m (L1) + 4 m (L 2) 1.00 mm 2 <40 m <8 m 1 m (L1) + 7 m (L 2) 1.50 mm 2 <70 m <12 m 1 m (L1) + 11 m (L 2) 2.50 mm 2 <100 m <20 m 1 m (L1) + 19 m (L 2) T ~ = ctuator = ontrol unit L1 = elimo connecting cable, 1 m (4 x 0.75 mm 2 ) W399_10 06/10 - Subject to change. elimo ircontrols (US), Inc. On/Off control W399_10 Floating Point control 57

58 10 GKX24-MFT-X1 ctuators, Multi-Function Technology imensions with 2-Way Valve M_GM_LineRevised H Technical ata GKX24-MFT-X1 Power supply 24V ±20% 50/60Hz 24V ±10% Power consumption 12W (3W) Transformer sizing 21V (class 2 power source) Electrical connection 18 G plenum rated cable ½" conduit connector protected NEM 2 (IP54) 3 ft [1m] 10 ft [3m] 16 ft [5m] Overload protection electronic throughout 0 to 95 rotation Operation range Y 2 to 10 V, 4 to 20m (default) variable (V,PWM, floating point, on/off) Input impedance 100kW (0.1 m), 500W 1500W (PWM, floating point, on/off) Feedback output U 2 to 10V, 0.5m max, V variable ngle of rotation max. 95, adjustable with mechanical stop electronically variable irection of rotation reversible with switch Fail-safe position adjustable with dial or tool 0 to 100% in 10% increments Position indication reflective visual indicator (snap-on) Manual override external push button Running time normal operation fail-safe 95 seconds (default), variable 90 to 150 seconds 35 seconds Humidity 5 to 95% RH non-condensing (EN ) mbient temperature -22 F to +122 F [-30 to +50 ] Storage temperature -40 F to +176 F [-40 to +80 ] Housing NEM2, IP54, UL enclosure type 2 Housing material UL94-5V gency list culus acc. to UL /-2-14 N/S E :02 E acc. to 2004/108/EE and 2006/95/E Noise level < 45d() Servicing maintenance free Quality standard ISO 9001 imensions (Inches) Non-Fail Safe (psi) Valve Size (Max) H GK F680H F6100HU F6125HU F SHP F SHP 2½ F SHP F SHP F SHP F SHP 2½ F SHP F SHP imensions with 3-Way Valve imensions (Inches) Non-Fail Safe (psi) Valve Size (Max) H GK F780HU F SHP F SHP 2½ F SHP Single_utterfly 06/10 - Subject to change. elimo ircontrols (US), Inc. 58

59 GKX24-MFT-X1 ctuators, Multi-Function Technology Wiring iagrams 1 Provide overload protection and disconnect as required. W399_utterfly 3 ctuators may also be powered by 24 V. 4 Position feedback cannot be used with Triac sink controller. The actuator internal common reference is not compatible. 5 ontrol signal may be pulsed from either the Hot (source) or the ommon (sink) 24 V line. 8 ontact closures & also can be triacs. & should both be closed for triac source and open for triac sink. 9 For triac sink the common connection from the actuator must be connected to the hot connection of the controller. Meets UL requirements without the need of an electrical ground connection. V/4-20 m W399_utterfly The ZG-R W resistor may be used. WRNING Live Electrical omponents! uring installation, testing, servicing and troubleshooting of this product, it may be necessary to work with live electrical components. Have a qualified licensed electrician or other individual who has been properly trained in handling live electrical components perform these tasks. Failure to follow all electrical safety precautions when exposed to live electrical components could result in death or serious injury. NOTE: Wiring diagrams shown are for single actuator mounted solutions PWM W399_utterfly 06/10 - Subject to change. elimo ircontrols (US), Inc. On/Off control W399_utterfly Floating Point control 59

60 10 M Series ctuators, On/Off, Floating Point imensions with 2-Way Valve M_GM_LineRevised H Models M24-3-X1 Technical ata Power supply 24 V ± 20% 50/60 Hz 24 V ± 10% Power consumption running 2.0 W holding 0.2 W Transformer sizing 5.5 V (class 2 power source) Electrical connection 3 ft, 18 G plenum rated cable ½ conduit connector Overload protection electronic throughout 0 to 95 rotation ontrol on/off, floating point Input impedance 600 W ngle of rotation 95, adjustable with mechanical stop irection of rotation reversible with protected switch Position indication handle Manual override external push button Running time 95 seconds Humidity 5 to 95% RH non condensing (EN ) mbient temperature -22 F to +122 F [-30 to +50 ] Storage temperature -40 F to +176 F [-40 to +80 ] Housing NEM 2/IP54 Housing material UL94-5V gency listings culus according to UL /-2-14, N/S E , S 22.2 No , E according to 89/336/EE (and 2006/95/E for line voltage and/or -S versions) Noise level <45d() Quality standard ISO 9001 imensions (Inches) Non-Fail Safe (psi) Valve Size (Max) H H HU F650H(U) F665H(U) 2½ F680HU imensions with 3-Way Valve imensions (Inches) Non-Fail Safe (psi) Valve Size (Max) H H HU F750H F765HU 2½ Single_utterfly 60

61 M Series ctuators, On/Off, Floating Point Wiring iagrams r serious injury. 24 V Transformer W557_10 2 UTION Equipment damage! ctuators may be connected in parallel. Power consumption and input impedance must be observed. 4 ctuators may also be powered by 24 V. Line Volts a open a closed The indication of direction is valid for switch position 1. a lk (1) ommon Red (2) + Wht (3) M24-3-X1 Meets culus or UL and S requirements without the need of an electrical ground connection. WRNING Live Electrical omponents! uring installation, testing, servicing and troubleshooting of this product, it may be necessary to work with live electrical components. Have a qualified licensed electrician or other individual who has been properly trained in handling live electrical components perform these tasks. Failure to follow all electrical safety precautions when exposed to live electrical components could result in death or serious injury. On/Off control erious injury. Line Volts 24 V Transformer lk (1) ommon Red (2) + Wht (3) + W557_10 The indication of direction is valid for switch position M24-3-X1 Floating Point or On/Off control 61

62 10 M Series ctuators, Multi-Function Technology imensions with 2-Way Valve M_GM_LineRevised H Models MX24-MFT-X1 imensions (Inches) Valve Size (Max) H F650H(U) F665H(U) 2½ F680HU Non-Fail Safe (psi) Technical ata Power supply 24 V ± 20% 50/60 Hz 24 V ± 10% Power consumption running 4 W holding 1.25 W Transformer sizing 6 V (class 2 power source) Electrical connection 3 ft [1m] 10 ft [3m] 16 ft [5m] 18 G plenum rated cable ½ conduit connector Overload protection electronic throughout 0 to 95 rotation Operating range Y 2 to 10 V, 4 to 20 m (default) Variable (V, PWM, Floating Point, On/Off) Input impedance 100k W (0.1 m), 500 W 1500 W (PWM, Floating Point, On/Off) Feedback output U 2 to 10 V, 0.5 m max V Variable ngle of rotation 95 electronically variable irection of rotation reversible with protected switch Position indication handle Manual override external push button Running time 150 seconds (default) variable (90 to 350 secs) Humidity 5 to 95% RH non condensing (EN ) mbient temperature -22 F to +122 F [-30 to +50 ] Storage temperature -40 F to +176 F [-40 to +80 ] Housing NEM 2/IP54 Housing material UL94-5V gency listings culus according to UL /-2-14, N/S E , S 22.2 No , E according to 89/336/EE Noise level <45d() Quality standard ISO 9001 Rated impulse voltage 4kV, ontrol pollution degree 3, Type of action 1 imensions with 3-Way Valve imensions (Inches) Non-Fail Safe (psi) Valve Size (Max) H H HU F750H F765HU 2½ Single_utterfly 62

63 M Series ctuators, Multi-Function Technology Wiring iagrams 3 ctuators may also be powered by 24 V Position feedback cannot be used with Triac sink controller. The actuator internal common reference is not compatible. ontrol signal may be pulsed from either the Hot (source) or the ommon (sink) 24 V line. ontact closures & also can be triacs. & should both be closed for triac source and open for triac sink. For triac sink the common connection from the actuator must be connected to the hot connection. The ZG-R W resistor converts the 4 to 20 m control signal to 2 to 10 V, up to 2 actuators may be connected in parallel. WRNING Live Electrical omponents! uring installation, testing, servicing and troubleshooting of this product, it may be necessary to work with live electrical components. Have a qualified licensed electrician or other individual who has been properly trained in handling live electrical components perform these tasks. Failure to follow all electrical safety precautions when exposed to live electrical components could result in death or serious injury. Two Position Line Volts Position 24 V/ Transformer ( ) Feedback V (+) Line Volts 24 V Transformer to 10 V Feedback Signal 11 a irection of rotation switch W W W W lk (1) ommon Red (2) Hot Wht (3) Y Input Org (5) U Output 3 lk (1) ommon Red (2) Hot + 10 Wht (3) Y1 Input Pnk (4) Y2 Input Org (5) U Output 2 to 10V W558_utterfly W558_utterfly Floating Point Line Volts ontrol Signal 4 to 20 m or 2 to 10 V 24 V Transformer ( ) (+) Ω 500Ω 1/4 watt lk (1) ommon Red (2) + Hot Wht (3) Y 1 Input, 2 to 10V Org (5) U Output, 2 to 10V W558_utterfly W W V/4-20 m PWM Line Volts 24 V Transformer ( only) Position Feedback V ( ) (+) 8 lk (1) ommon Red (2) + Hot Wht (3) Y Input Org (5) U Output W558_utterfly 63

64 GM24-3-X1 ctuators, On/Off, Floating Point imensions with 2-Way Valve M_GM_LineRevised H Models GM24-3-X1 Technical ata Power supply 24 V ± 20% 50/60 Hz 24 V ± 10% Power consumption running 4.0 W holding 2 W Transformer sizing 6 V (class 2 power source) Electrical connection 3 ft, 18 G appliance cable, 1/2 conduit connector Overload protection electronic throughout 0 to 95 rotation ontrol signal On/Off, Floating Point Input impedance 600 W ngle of rotation mechanically limited to 95 irection of rotation reversible with switch / Position indication 0 to 1 and reversible indicator Running time 150 sec. Humidity 5 to 95% RH non-condensing mbient temperature -22 F to 122 F [-30 to 50 ] Storage temperature -40 F to 176 F [-40 to 80 ] Housing NEM 2/IP54 Housing material UL94-5V (flammability rating) gency listings culus according to UL /-2-14, N/S E , S 22.2 No.24-93, E according to 89/336/EE Noise level max. 45 d () Servicing maintenance free Quality standard ISO 9001 imensions (Inches) Non-Fail Safe (psi) Valve Size (Max) H GM 2*GM F680H F6100H F6100HU F6125HU F6150HU F SHP F SHP 2½ F SHP F SHP F SHP F SHP 2½ F SHP F SHP

65 GM24-3-X1 ctuators, On/Off, Floating Point imensions with 3-Way Valve V Transformer W559 Line Volts lk (1) ommon Red (2) + a open a closed a Wht (3) The indication of direction is valid for switch position 1. GM24-3-X1 imensions (Inches) Non-Fail Safe (psi) Valve Size (Max) H GM 2*GM F765H 2½ F780H F780HU F7100H F7100HU F7125HU F7150HU F SHP F SHP 2½ F SHP On/Off Floating Point erious injury. Line Volts 24 V Transformer The indication of direction is valid for switch position lk (1) ommon Red (2) + Wht (3) GM24-3-X1 W559 F SHP F SHP F SHP 2½ F SHP F SHP Wiring iagrams 2 UTION Equipment damage! ctuators may be connected in parallel. Power consumption and input impedance must be observed. 3 ctuators may also be powered by 24 V. ctuators with plenum rated cable do not have numbers on wires; use 5 color codes instead. ctuators with appliance cables are numbered. Meets culus or UL and S requirements without the need of an electrical ground connection. WRNING Live Electrical omponents! uring installation, testing, servicing and troubleshooting of this product, it may be necessary to work with live electrical components. Have a qualified licensed electrician or other individual who has been properly trained in handling live electrical components perform these tasks. Failure to follow all electrical safety precautions when exposed to live electrical components could result in death or serious injury. 65

66 GMX24-MFT-X1 ctuators, Multi-Function Technology imensions with 2-Way Valve M_GM_LineRevised Models GMX24-MFT-X1 Technical ata Power supply 24 V ± 20% 50/60 Hz 24 V ± 10% Power consumption running 4.5 W holding 2 W Transformer sizing 7 V (class 2 power source) Electrical connection 3 ft, 18 G appliance cable, 1/2 conduit connector Overload protection electronic throughout 0 to 95 rotation ontrol signal 2 to 10 V, 4 to 20 m (with 500 W, 1/4 W resistor) ZG-R01 Input impedance 100 k W for 2 to 10V (0.1 m) 500 W for 4 to 20 m 750 W for PWM 1500 W for on/off and floating point ngle of rotation mechanically limited to 95 irection of rotation reversible with switch / Position indication 0 to 1 and reversible indicator Running time 150 sec. Humidity 5 to 95% RH non-condensing mbient temperature -22 F to 122 F [-30 to 50 ] Storage temperature -40 F to 176 F [-40 to 80 ] Housing NEM 2/IP54 Housing material UL94-5V (flammability rating) gency listings culus according to UL /-2-14, N/S E , S 22.2 No.24-93, E according to 89/336/EE Noise level max. 45 d () Servicing maintenance free Quality standard ISO 9001 H imensions (Inches) Non-Fail Safe (psi) Valve Size (Max) H GM 2*GM F680H F6100H F6100HU F6125HU F6150HU F SHP F SHP 2½ F SHP F SHP F SHP F SHP 2½ F SHP F SHP imensions with 3-Way Valve imensions (Inches) Non-Fail Safe (psi) Valve Size (Max) H GM 2*GM F765H 2½ F780H F780HU F7100H F7100HU F7125HU F7150HU F SHP F SHP 2½ F SHP F SHP F SHP F SHP 2½ F SHP F SHP

67 GMX24-MFT-X1 ctuators, Multi-Function Technology Wiring iagrams 3 ctuators may also be powered by 24 V ctuators with plenum rated cable do not have numbers on wires; use color coded instead. ctuators with appliance rated cable use numbers. ontrol signal may be pulsed from either the Hot (Source) or ommon (Sink) 24 V line. For triac sink the ommon connection from the actuator must be connected to the Hot connection of the controller. Line Volts ontrol Signal 4 to 20 m or 2 to 10 V 24 V Transformer ( ) (+) Ω 500Ω 1/4 watt lk (1) ommon Red (2) + Hot Wht (3) Y 1 Input, 2 to 10V Org (5) U Output, 2 to 10V W W W545_No_2 V/4-20 m Meets culus or UL and S requirements without the need of an electrical ground connection. ontact closures & also can be triacs. & should 9 both be closed for triac source and open for triac sink. Position feedback cannot be used with a Triac sink controller. The 11 actuator internal common reference is not compatible. WRNING Live Electrical omponents! uring installation, testing, servicing and troubleshooting of this product, it may be necessary to work with live electrical components. Have a qualified licensed electrician or other individual who has been properly trained in handling live electrical components perform these tasks. Failure to follow all electrical safety precautions when exposed to live electrical components could result in death or serious injury. Line Volts 3 ontrol Signal 2 to 10 V 24 V Transformer ( ) (+) Master lk (1) ommon Red (2) + Hot Wht (3) Y Input, 2 to 10 V Org (5) U Output 2 to 10 V W W Slave W W 5 5 lk (1) ommon Red (2) + Hot Wht (3) Y Input, 2 to 10 V Org (5) U Master_Slave Two Position Floating Point PWM Line Volts Position 24 V/ Transformer ( ) Feedback V (+) Line Volts Line Volts 24 V Transformer 8 2 to 10 V Feedback Signal a irection of rotation switch W W W W 5 24 V Transformer ( only) Position Feedback V ( ) (+) 8 3 lk (1) ommon Red (2) Hot Wht (3) Y Input Org (5) U Output 3 lk (1) ommon Red (2) Hot + 10 Wht (3) Y 1 Input Pnk (4) Y 2 Input Org (5) U Output 2 to 10V lk (1) ommon Red (2) + Hot Wht (3) Y Input Org (5) U Output W545_No_2 W545_No_2 W545_No_2 Master/Slave 67

68 NSV-SY attery ack-up System For elimo SY Series Electric ctuators, 2 Position or Modulating pplication Typically, applications requiring fail-safe operation of actuated devices have had to rely on either the limited power of mechanical spring return actuators, or use costly high pressure pneumatic devices to provide fail-safe positioning. Model NSV series computer-grade UPS back-up systems designed for use with SY Series electric industrial quarter-turn actuators provides the power necessary to drive these actuators to a field selectable fail-safe position. The system consists of a painted steel key lock hinged door controls cabinet which houses the logic switching, all field wiring terminal points and a computer-grade back-up system. The back-up system is a component-level device which utilizes a replaceable spill-proof battery pack that can be readily purchased at most office-supply centers. Provides Fail-Safe Operation for SY Series Industrial Electric ctuators, SY1 thru SY12. Field Selectable Fail irection Readily vailable Sealed Lead-cid attery Packs Provides 500% of Power Requirements for Full Load ycle Safety in Numbers The system is designed to provide at a minimum up to 500% of the power required to drive the various actuators through their full 90 degree rotation at full running amperage draws. However, when the actuators have reached their field-selectable end-of-travel positions, current draw drops to zero and the back-up system sits idle until either the time-out function integral to the battery is reached or the mains power returns, whichever occurs first. Simple User Interface Key Lock Hinged Front Steel ontrols Enclosure Indicator lights visible through the viewport on the front and side of the control cabinet give status indication of mains power, back-up system charging and fail-safe operation. The NSV series is powered from building power and all power and logic interface wiring passes through the control cabinet. There are two different series produced, one is used for actuators which operate under 2 position or on/off control schemes, while the second series is used for actuators operating under proportional control schemes. Various models are available within these two series to provide the most cost effective and efficient means of providing fail-safe operation for these actuators. 68

69 NSV-SY attery ack-up System For elimo SY Series Electric ctuators, 2 Position or Modulating T1 MINS POWER G N GN L2 (NEUTRL) 120V.. LINE VOLTGE H L1 (HOT) ONTROL LOGI M3 8 M2 FIEL LOGI LOSE LINE SENSE SWITHING GRN G T 7 GREEN GROUNING SREW +t HETER (OPT.) NOTE: TERMINL #7 LSO POWERS OTHER ELETRONIS & MUST E WIRE WVEFORM GENERTOR 1 THERML OVERLO UTOMTI RESET M1 120V SY TUTOR M2 M M3 7 5 NO PITOR TUTOR RIVE 1 5 LOSE OM OM N NO N SWITH 1 SWITH 2 NO 6 OM N SWITH 3 NOTE: SWITHES SHOWN WITH TUTOR FULLY F NO OM SWITH 4 N E K-UP SYSTEM INET Sequence of Operation - 2 Position ontrol FIEL WIRING TUTOR WIRING The back up system is wired in series between the mains power and the actuator. Under normal operation, power supplied to T1 H & N terminals will illuminate the green LINE IN indicator light and provide charging voltage to the battery system. While under mains power, the field select switch (or form contacts) are enabled to control the positioning of the actuator. The end user can install a center-off switch for 3 point floating control, a SPT toggle switch for 2 position control, or interface through an automation system s form contacts. ny method of operation will not affect the back up unit s operation. While under mains power, the blue T HRGING indicator light is illuminated while the yellow /U POWER indicator light remains off. While under mains power, the position of the FIL POSITION SELET switch is irrelevant. Power is supplied through the interface cabinet and the actuator heater is enabled. No current is being drawn from the battery system during this mode of operation. When the mains power is lost, charging power is no longer supplied to the battery system, and the green LINE IN indicator light is turned off. The battery system automatically generates modified-sine wave line voltage to provide power for the actuator. The blue T HRGING indicator light is turned off, and the yellow /U POWER indicator light is turned on. The FIL POSITION SELET switch becomes active, and depending on its position, drives the actuator either fully open or fully closed. uring this mode of operation, the heater is NOT energized, and the position of any field interface switching is irrelevant. The battery system will provide ample power to drive the actuator more than 5 full torque cycles. However, once the actuator reaches its end-of-travel limit switch, power drain from the back-up system is reduced to the requirements of the yellow /U POWER indicator light. fter 15 minutes, the battery system turns itself off and waits for the mains power to return. The gear train design of the SY actuator provides automatic locking of the actuator position after the battery system shuts down. Normal operation is resumed when mains power returns. 69

70 NSV-SY attery ack-up System For elimo SY Series Electric ctuators, 2 Position or Modulating Sequence of Operation - Modulating ontrol Note: This Model requires modification to SY-MFT Model interface wiring inside the SY actuator. The back up system is wired in series between the mains power and the actuator. Under normal operation, power supplied to T1 H & N terminals will illuminate the green LINE IN indicator light and provide charging voltage to the battery system. While mains power is present, the SY drive logic interface card is enabled and provides proportional positioning of the SY actuator in response to incoming signals from customer supplied field automation devices. While under mains power, the blue T HRGING indicator light is illuminated while the yellow /U POWER indicator light remains off. While under mains power, the position of the FIL POSITION SELET switch is irrelevant. Power is supplied through the interface cabinet and the actuator heater is enabled. ll internal actuator controls are otherwise not affected by the backup system. ll movement of the actuator is controlled by the automation control system. No current is being drawn from the battery system during this mode of operation. When the mains power is lost, charging power is no longer supplied to the battery system, and the green LINE IN indicator light is turned off. The battery system automatically generates modified-sine wave line voltage to provide power for the actuator. The blue T HRGING indicator light is turned off, and the yellow /U POWER indicator light is turned on. The FIL POSITION SELET switch becomes active, and depending on its position, drives the actuator either fully open or fully closed. uring this mode of operation the incoming proportional signal is irrelevant. The battery system will provide ample power to drive the actuator more than 5 full torque cycles. However, once the actuator reaches its end-of-travel limit switch, power drain from the back-up system is reduced to the requirements of the yellow /U POWER indicator light. fter 15 minutes, the battery system turns itself off and waits for the mains power to return. The gear train design of the SY actuator provides automatic locking of the actuator position after the battery system shuts down. Normal operation is resumed when mains power returns. 70

71 NSV-SY attery ack-up System For elimo SY Series Electric ctuators, 2 Position or Modulating Key ccess and Status Viewports attery System Status Indicators ll onnections to P ackup are Modular onnection to P Interface SIZING N PERFORMNE HRT ctuator Model Torque Output Runtime (secs) raw (amps) 2 Position Model Modulating Model Runtime at 50% apacity (minutes) % apacity Used at Full Runtime Replacement attery SY1-110(P) NSV-SY-01 NSV-SY % R2 SY2-110(MFT) NSV-SY-01 NSV-SY % R2 SY3-110(MFT) NSV-SY-01 NSV-SY % R2 SY4-110(MFT) NSV-SY-01 NSV-SY % R2 SY5-110(MFT) NSV-SY-01 NSV-SY % R2 SY6-110(MFT) NSV-SY-01 NSV-SY % R2 SY7-110(MFT) NSV-SY-03 NSV-SY % R2 SY8-110(MFT) NSV-SY-05 NSV-SY % R32 SY9-110(MFT) NSV-SY-05 NSV-SY % R32 SY10-110(MFT) NSV-SY-05 NSV-SY % R32 SY11-110(MFT) NSV-SY-05 NSV-SY % R32 SY12-110(MFT) NSV-SY-05 NSV-SY % R32 SY1-24(P) NSV-SY-11 NSV-SY % R2 SY2-24(MFT) NSV-SY-11 NSV-SY % R2 SY3-24(MFT) NSV-SY-11 NSV-SY % R2 SY4-24(MFT) NSV-SY-11 NSV-SY % R2 SY5-24(MFT) NSV-SY-11 NSV-SY % R2 SY1-220(P) NSV-SY-21 NSV-SY % R2 SY2-220(MFT) NSV-SY-21 NSV-SY % R2 SY3-220(MFT) NSV-SY-21 NSV-SY % R2 SY4-220(MFT) NSV-SY-21 NSV-SY % R2 SY5-220(MFT) NSV-SY-21 NSV-SY % R2 SY6-220(MFT) NSV-SY-21 NSV-SY % R2 SY7-220(MFT) NSV-SY-23 NSV-SY % R32 SY8-220(MFT) NSV-SY-23 NSV-SY % R32 SY9-220(MFT) NSV-SY-23 NSV-SY % R32 SY10-220(MFT) NSV-SY-25 NSV-SY % R32 SY11-220(MFT) NSV-SY-25 NSV-SY % R32 SY12-220(MFT) NSV-SY-25 NSV-SY % R32 71

72 NSV-SY attery ack-up System Wiring iagrams UTOMTION SYSTEM OR SWITH M3 LOSE M2 8 H 110V ~ N G LOSE 1 TUTOR #1 G G UX SW TERMINLS E F Open = H to 3 Opened = to NSV-SY-01 NSV-SY-03 NSV-SY-05 FIEL WIRING lose = Hot = H to 4 losed = to F H to V MX SY(1-12)-110 Wiring diagram for a single on/off SY series 110vac actuator. uilding mains power is connected to G, N & H terminals. control switch or dry contacts are connected between terminal 8 and M2 or M3 to control the positioning of the actuator under power. Terminals G, 1, 5, 6 & 7 are connected to the SY actuator as shown. Observe wire size rules for longer wire runs. 72

73 NSV-SY attery ack-up System Wiring iagrams UTOMTION SYSTEM OR SWITH M3 LOSE M2 8 H K1-110V ~ TUTOR #1 UX SW TERMINLS N G E F Open = H to 3 Opened = to G lose = H to 4 losed = to F Hot = H to V MX 7 6 LOSE 5 K1 K1-1 G NSV-SY-01 Max Load 150V NSV-SY-03 Max Load 300V NSV-SY-05 Max Load 500V FIEL WIRING NOTES: K1 OIL MUST MTH SUPPLY VOLTGE. IN THIS SENRIO, TUTOR #1 WORKS OPPOSITE TUTOR #2. IN THIS EXMPLE, K1 IS 4PT RELY. NOTE: o NOT exceed total V capacity of NSV-SY backup system. Wiring diagram for multiple on/off SY series 110vac actuators. G TUTOR #2 UX SW TERMINLS E F Open = H to 3 lose = H to 4 Hot = H to V MX SY(1-12)-110 OSERVE POLRITY OF ONTROL SIGNLS N POWER Opened = to losed = to F o NOT exceed the Max Loads as stated above when connecting multiple actuators. ctuators connected in this manner operate in parallel from the common automation control switch and will fail-safe position together. uilding mains power is connected to G, N & H terminals. control switch or dry contacts are connected between terminal 8 and M2 or M3 to control the positioning of the actuator under power. Terminals G, 1, 5, 6 & 7 are connected to the SY actuator as shown. Observe wire size rules for longer wire runs. 73

74 NSV-SY attery ack-up System Wiring iagrams Wiring diagram for a single proportional SY series 110vac actuator. uilding mains power is connected to G, N & H terminals. The control signal from the automation system is wired directly to the SY actuator. Terminals G, 2, 5, 6, M2 & M3 are connected to the SY actuator as shown. Observe wire size rules for longer wire runs. 74

75 NSV-SY attery ack-up System Wiring iagrams Wiring diagram for multiple proportional SY series 110vac actuators. o NOT exceed the Max Loads as stated above when connecting multiple actuators. ctuators connected in this manner operate in parallel from the common automation control signal and will fail-safe position together. uilding mains power is connected to G, N & H terminals. The control signal from the automation system is wired directly to the SY actuator. Terminals G, 2, 5, 6, M2 & M3 are connected to the SY actuators as shown. Observe wire size rules for longer wire runs. 75

76 NSV-SY attery ack-up System Wiring iagrams UTOMTION SYSTEM OR SWITH M3 LOSE M2 8 H 110V ~ N G LOSE 1 TUTOR #1 G G UX SW TERMINLS E F NSV-SY-11 FIEL WIRING Open = H to lose = H to Hot = H to Opened = to losed = to F 5 250V MX SY(1-5)-24 OSERVE POLRITY OF ONTROL SIGNLS N POWER Wiring diagram for a single on/off SY series 24vac actuator. uilding mains power is connected to G, N & H terminals. control switch or dry contacts are connected between terminal 8 and M2 or M3 to control the positioning of the actuator under power. Terminals G, 1, 5, 6 & 7 are connected to the SY actuator as shown. Observe wire size rules for longer wire runs. The 24vac transformer required to run the SYxxx-24 actuator is built in to the NSV cabinet. 76

77 NSV-SY attery ack-up System Wiring iagrams UTOMTION SYSTEM OR SWITH M3 LOSE M2 8 H K1-110V ~ TUTOR #1 UX SW TERMINLS N G E F Open = H to 3 Opened = to G lose = H to 4 losed = to F Hot = H to V MX 7 6 LOSE 5 K1 K1-1 G G TUTOR #2 UX SW TERMINLS E F NSV-SY-11 Max Load 150V FIEL WIRING NOTES: K1 OIL MUST MTH SUPPLY VOLTGE. IN THIS SENRIO, TUTOR #1 WORKS OPPOSITE TUTOR #2. IN THIS EXMPLE, K1 IS 4PT RELY. Open = H to 3 Opened = to lose = H to 4 losed = to F Hot = H to V MX SY(1-5)-24 OSERVE POLRITY OF ONTROL SIGNLS N POWER NOTE: o NOT exceed total V capacity of NSV-SY backup system. Wiring diagram for multiple on/off SY series 24vac actuators. o NOT exceed the Max Loads as stated above when connecting multiple actuators. ctuators connected in this manner operate in parallel from the common automation control switch and will fail-safe position together. uilding mains power is connected to G, N & H terminals. control switch or dry contacts are connected between terminal 8 and M2 or M3 to control the positioning of the actuator under power. Terminals G, 1, 5, 6 & 7 are connected to the SY actuator as shown. Observe wire size rules for longer wire runs. The 24vac transformer required to run the SYxxx-24 actuator is built in to the NSV cabinet. 77

78 NSV-SY attery ack-up System Wiring iagrams Wiring diagram for a single proportional SY series 24vac actuator. uilding mains power is connected to G, N & H terminals. The control signal from the automation system is wired directly to the SY actuator. Terminals G, 2, 5, 6, M2 & M3 are connected to the SY actuator as shown. Observe wire size rules for longer wire runs. The 24vac transformer required to run the SYxxx-24 actuator is built in to the NSV cabinet. 78

79 NSV-SY attery ack-up System Wiring iagrams Wiring diagram for multiple proportional SY series 24vac actuators. o NOT exceed the Max Loads as stated above when connecting multiple actuators. ctuators connected in this manner operate in parallel from the common automation control signal and will fail-safe position together. uilding mains power is connected to G, N & H terminals. The control signal from the automation system is wired directly to the SY actuator. Terminals G, 2, 5, 6, M2 & M3 are connected to the SY actuators as shown. Observe wire size rules for longer wire runs. The 24vac transformer required to run the SYxxx-24 actuator is built in to the NSV cabinet. 79

80 NSV-SY attery ack-up System Wiring iagrams UTOMTION SYSTEM OR SWITH M3 LOSE M2 8 L1 220V ~ L2 G LOSE 1 TUTOR #1 G G UX SW TERMINLS E F Open = to 3 Opened = to NSV-SY-21 NSV-SY-23 NSV-SY-25 FIEL WIRING lose = Hot = to 4 losed = to F to V MX SY(1-12)-220 Wiring diagram for a single on/off SY series 220vac actuator. uilding mains power is connected to G, N & H terminals. control switch or dry contacts are connected between terminal 8 and M2 or M3 to control the positioning of the actuator under power. Terminals G, 1, 5, 6 & 7 are connected to the SY actuator as shown. Observe wire size rules for longer wire runs. 80

81 NSV-SY attery ack-up System Wiring iagrams UTOMTION SYSTEM OR SWITH M3 LOSE M2 8 L1 K1-220V ~ TUTOR #1 UX SW TERMINLS L2 G E F Open = to 3 G 4 F Hot = to V MX 7 6 LOSE 5 K1 K1-1 G NSV-SY-21 Max Load 150V NSV-SY-23 Max Load 300V NSV-SY-25 Max Load 500V FIEL WIRING NOTES: K1 OIL MUST MTH SUPPLY VOLTGE. IN THIS SENRIO, TUTOR #1 WORKS OPPOSITE TUTOR #2. IN THIS EXMPLE, K1 IS 4PT RELY. NOTE: o NOT exceed total V capacity of NSV-SY backup system. Wiring diagram for multiple on/off SY series 220vac actuators. G Open = Hot = to to TUTOR #2 UX SW TERMINLS SY(1-6)-220 OSERVE POLRITY OF ONTROL SIGNLS N POWER E 5 250V MX o NOT exceed the Max Loads as stated above when connecting multiple actuators. ctuators connected in this manner operate in parallel from the common automation control switch and will fail-safe position together. uilding mains power is connected to G, N & H terminals. control switch or dry contacts are connected between terminal 8 and M2 or M3 to control the positioning of the actuator under power. Terminals G, 1, 5, 6 & 7 are connected to the SY actuator as shown. Observe wire size rules for longer wire runs. F F 81

82 NSV-SY attery ack-up System Wiring iagrams Wiring diagram for a single proportional SY series 220vac actuator. uilding mains power is connected to G, N & H terminals. The control signal from the automation system is wired directly to the SY actuator. Terminals G, 2, 5, 6, M2 & M3 are connected to the SY actuator as shown. Observe wire size rules for longer wire runs. 82

83 NSV-SY attery ack-up System Wiring iagrams Wiring diagram for multiple proportional SY series 220vac actuators. o NOT exceed the Max Loads as stated above when connecting multiple actuators. ctuators connected in this manner operate in parallel from the common automation control signal and will fail-safe position together. uilding mains power is connected to G, N & H terminals. The control signal from the automation system is wired directly to the SY actuator. Terminals G, 2, 5, 6, M2 & M3 are connected to the SY actuators as shown. Observe wire size rules for longer wire runs. 83

84 attery ack-up System For elimo SY Series Electric ctuators, 2 Position or Modulating K-UPS S 350V/PRT NUMER: K350 vailability: North merica, Latin merica Product Overview escription P ack-ups, 350V/210W, Input 120V/ Output 120V General Features ddl Surge Protected Outlets, udible larms, ord Management, Intelligent attery Management, Internet FX - modem - SL protection, Overload Indicator, Replace att Indicator, Site wiring fault indicator, Software, User Replaceable batteries ocumentation User Manual K-UPS S 500V/PRT NUMER: K500 vailability: North merica, Latin merica Product Overview escription P ack-ups, 500V/300W, Input 120V/ Output 120V General Features ddl Surge Protected Outlets, udible larms, ord Management, Intelligent attery Management, Internet FX - modem - SL protection, Overload Indicator, Replace att Indicator, Site wiring fault indicator, Software, User Replaceable batteries ocumentation User Manual Technical Specifications Input Nominal input 120 V Input frequency 50/60 Hz +/- 5 Hz (auto sensing) Input onnection Type NEM 5-15P ord Length 6 feet Input voltage range for main operations V Output Output power capacity 350 V Output power capacity 210 Watts Nominal output voltage 120 V Waveform type Stepped approximation to a sinewave Output onnections (3) NEM 5-15R (3) NEM 5-15R (Surge) atteries Typical backup time at half load 11.4 minutes attery type Maintenance-free sealed Lead-cid battery with suspended electrolyte: leakproof Typical recharge time ** 8 hour(s) Replacement battery cartridge (1) R2 ommunications & Management ontrol panel LE status display with On Line: On attery: Replace attery and Overload indicators udible alarm larm when on battery: distinctive low battery alarm : overload continuous tone alarm Surge Protection and Filtering Surge energy rating 480 joules Filtering Full time multi-pole noise filtering: 5% IEEE surge letthrough: zero clamping response time: meets UL 1449 ataline protection RJ-11 Modem/Fax/SL protection (two wire single line) Technical Specifications Input Nominal input 120 V Input frequency 50/60 Hz +/- 5 Hz (auto sensing) Input onnection Type NEM 5-15P ord Length 6 feet Input voltage range for main operations V Output Output power capacity 500 V Output power capacity 300 Watts Nominal output voltage 120 V Waveform type Stepped approximation to a sinewave Output onnections (3) NEM 5-15R (3) NEM 5-15R (Surge) atteries Typical backup time at half load 11.4 minutes attery type Maintenance-free sealed Lead-cid battery with suspended electrolyte: leakproof Typical recharge time ** 8 hour(s) Replacement battery cartridge (1) R2 ommunications & Management ontrol panel LE status display with On Line: On attery: Replace attery and Overload indicators udible alarm larm when on battery: distinctive low battery alarm: overload continuous tone alarm Surge Protection and Filtering Surge energy rating 480 joules Filtering Full time multi-pole noise filtering: 5% IEEE surge letthrough: zero clamping response time: meets UL 1449 ataline protection RJ-11 Modem/Fax/SL protection (two wire single line) 84

85 attery ack-up System For Powered elimo SY Series Electric ctuators, 2 Position or Modulating K-UPS 900V/PRT NUMER: R900 vailability: North merica, Latin merica Product Overview escription P ack-ups, 900V/540W, Input 120V/ Output 120V General Features udible larms, utomatic Voltage Regulation (VR), Easy Overload Recovery, Ethernet Protection, Hot Swap atteries, Modem Protection, Overload Indicator, Replace att Indicator, Site wiring fault indicator, User Replaceable batteries ocumentation User Manual PHYSIL IMENSIONS NSV-SY Series ack-up Systems Maximum imensions NSV NSV-SY NSV-SY 01, 02 21, 22 03, 04, 11 12, 23, 24 05, 06 25, 26 Height Width epth Net weight 36# 42# 44# Technical Specifications Input Nominal input voltage 120 V Input frequency 50/60 Hz +/- 3 Hz (auto sensing) Input onnection Type NEM 5-15P ord Length 6 feet Input voltage range for main operations V Output Output power capacity 900 V Output power capacity 540 Watts Nominal output voltage 120 V Waveform type Stepped approximation to a sinewave Shipping Weight 38# 44# 48# Environmental Operating Relative Humidity 0-95% Operating Elevation feet ( m) Storage Temperature (5-113 F) Storage Relative Humidity 0-95% Storage Elevation feet ( m) udible noise at 1 meter from surface of unit 45 d Online thermal dissipation 24 TU/hr Output onnections (7)NEM 5-15R atteries Typical backup time at half load 17.6 minutes attery type Maintenance-free sealed Lead-cid battery with suspended electrolyte: leakproof Typical recharge time ** 8 hour(s) Replacement battery cartridge (1) R32 ommunications & Management ontrol panel LE status display with On Line: On attery: Replace attery and Overload indicators udible alarm larm when on battery: distinctive low battery alarm: overload continuous tone alarm Surge Protection and Filtering Surge energy rating 320 joules Filtering Full time multi-pole noise filtering: 5% IEEE surge letthrough: zero clamping response time: meets UL 1449 ataline protection RJ-11 Modem/Fax/SL protection (two wire single line) plus RJ-45 ethernet onformance - P ack UP Module pprovals S, F, UL 1778 pprovals F Part 15 lass, Industry anada, UL 1778, cul Listed ** The time to recharge to 90% of full battery capacity following a discharge to shutdown using a load rated for 1/2 the full load rating of the UPS. 85