Butterfly Valves (BFV)

Size: px
Start display at page:

Download "Butterfly Valves (BFV)"

Transcription

1 utterfly Valves (FV) pplication comprehensive line of utterfly Valves is available in sizes ranging from 2 to 30 in both standard and high performance. Victaulic valves are available to 12. ll utterfly Valves fulfill the commercial and industrial HV application requirement for positive shut-off for liquids. pplications Include: hillers Isolation ooling Tower Isolation hange-over Systems Large ir Handlers oil ontrols ypass and Related Process ontrol Standard, grooved and high performance utterfl y Valves meet a wide range of commercial and industrial HV applications dvanced seat and disc designs provide bubble tight shut-off capability at each valves specified temperature and pressure while maintaining a low seating torque elimo offers NEM 2, NEM 4 and NEM 4X actuators to ensure control in a variety of environments. Standard H/HU series valves incorporate a five bushing design to isolate the valve shaft from the body for better control Stainless steel or nickel plated discs are standard for superior strength and durability ensuring a long lasting operation Grooved valves are WW rated for potable water in the United States. heck local laws for anada 1

2 Nomenclature utterfly Valves (FV) F6 H SY2 24 -MFT Valve F6 = 2-way F7 = 3-way Valve Size 50 = 2 65 = 2 1/2 80 = = = = = = = = = = = = = 30 ORERING EXMPLE Trim Material HU = Stainless isc, ast uctile Iron Full Lug ody, EPM Liner, ubble Tight lose-off to 50 psi H = Stainless isc, ast uctile Iron Full Lug ody, EPM Liner, ubble Tight lose-off to 200 psi (2 to 12 ), 150 psi (14 +) -150SHP = NSI lass 150, Stainless isc, ast Steel Full Lug ody, RPTFE Seat, ubble Tight lose-off up to 285 psi -300SHP = NSI lass 300, Stainless isc, ast Steel Full Lug ody, RPTFE Seat, ubble Tight lose-off up to 600 psi -VI = Grooved WW (606) Nickel oated Iron isc, ast uctile Iron STM 536, Grooved Fitting, EPM Seat, ubble Tight lose-off to 200 psi ctuator Type Non-Spring Return R(X)... GR(X)... R... N4 GR/GM... N4 GM(X) SY Electronic Fail- Safe GK... KR...N4 Spring Return F Power Supply -24 = 24 V/ -110 = 110/120 V -120 = 120 V -230 = 230 V UP = V ontrol lank = On/Off -3-X1 = On/Off, Floating Point MFT or MFT-X1 = Multi-Function Technology -S = uilt-in uxiliary Switch -X1=Water onfi guration Non-Spring Return Spring Return 2 Pos. Modulating 1 hoose the valve actuator combination. N NO NO/FO N/F NO/FO NO/F N/FO N/F 2 2-way Preference F650H+SY2-24MFT Set Up Required Field Logic etermines Normal Position (Normally losed) 1 V/2V/4m = losed (Normally Open) 1V/2V/4m = Open Specify preference or confi guration. (Normally Open/Fail Open) Field Logic etermines Normal Position Spring Fails Valve OPEN (Normally losed/fail losed) Field Logic etermines Normal Position Spring Fails Valve LOSE (Normally Open/Fail Open) 1V/2V/4m = Open Spring Fails Valve OPEN (Normally Open/Fail losed) 1V/2V/4m = Open Spring Fails Valve LOSE (Normally losed/fail Open) 1V/2V/4m = losed Spring Fails Valve OPEN (Normally losed/fail losed) 1V/2V/4m = losed Spring Fails Valve LOSE Set-Up 2 Pos. Non-Spring Return Modulating 3 Specify Flow Pattern [10-35] Spring Return Modulating 2 Pos. Specify Flow Pattern [10-35] +NO For MFT orders only - select programming code (consult factory) No Set Up Required Field Logic etermines Normal Position Master (ctuated) Valve N (Normally losed) 1 V/2 V/4m = losed Master (ctuated) Valve NO (Normally Open) 1 V/2V/4m = Open +Tagging (if needed) 3-way onfiguration NO/FO (Normally Open/Fail Open) Field Logic etermines Normal Position Spring Fails Master Valve OPEN N/F (Normally losed/fail losed) Field Logic etermines Normal Position Spring Fails Master Valve LOSE NO/FO (Normally Open/Fail Open) 1 V/2V/4m = Master Valve Open Spring Fails Master Valve OPEN NO/F (Normally Open/Fail losed) 1 V/2V/4m = Maser Valve Open Spring Fails Master Valve LOSE N/FO (Normally losed/fail Open) 1 V/2V/4m = Master Valve losed Spring Fails Master Valve OPEN N/F (Normally losed/fail losed) 1 V/2V/4m = Master Valve losed Spring Fails Master Valve LOSE 4 oes order require tagging? Tagging: Valves may be tagged per customer specifi cation. ($10.00 per tag) Example: hiller 1 3rd Floor East Part number for tagging: omplete Ordering Example: F650H+SY2-24MFT+NO +E onsult factory 2

3 Features / enefits Standard Performance utterfly Valves elimo resilient seat H(U)... Series utterfly Valves are designed for use in NSI lass 150 piping systems and are supplied in standard lug style body designs. VLVE ESIGN FETURES Unique seat and disc design ensures positive valve sealing while maintaining low seating torque utterfly valve discs are precision machined to half ball profile, providing a precise disc-to-seat relationship artridge style seat incorporates an elastomer bonded to a phenolic stabilizing ring, eliminating elastomer movement and reducing seat tearing or fatiguing due to bunching artridge seat has a much smaller mass of elastomer than traditional boot seat designs, limiting seat swell and the accompanying variations in seating torque The five bushing design completely isolates the valve shaft from the body, resulting in increased control of the valve disc, lower valve seating torque, and longer valve life uctile Iron Full Lug odies EPM liner Stainless Steel isc Two Models to suit the application: HU Series provides economical HV solutions up to 50 psi close-off with a 200 psi body rating (2-12 ) H Series provides full-rated close-off to 200 psi (2 12 ) or 150 psi (14 30 ) 2-way and 3-way applications ISO5211 ESIGN UTILE IRON OY I TG RPTFE TOP USHING EPM O-RING RPTFE USHINGS NSI OLT PTTERN PIN 304SS IS 416SS SHFT RPTFE LOWER USHING 3

4 H(U) Series utterfly Valves Standard ctuation (verage ssembly Weights) UNERUT MOELS 2-WY 3-WY TUTOR NON-SPRING RETURN SPRING RETURN ELETRONI FIL-SFE Size Valve Max GPM OP M(X) GM(X) 2*GM(X) F... 2*F... GK... 2*GK... 2 F650HU lbs. 14 lbs. 2.5 F665HU lbs. 14 lbs. 3 F680HU lbs. 25 lbs. 4 F6100HU lbs. 34 lbs. 25 lbs. 5 F6125HU lbs. 39 lbs. 30 lbs. 6 F6150HU lbs. 45 lbs. 2 F750HU lbs. 46 lbs. 2.5 F765HU lbs. 65 lbs. 3 F780HU lbs. 72 lbs. 63 lbs. 4 F7100HU lbs. 124 lbs. 5 F7125HU lbs. 154 lbs. 6 F7150HU lbs. 188 lbs. FULL RTE MOELS 2-WY 3-WY NON-SPRING RETURN SPRING RETURN ELETRONI FIL-SFE Size Valve Max GPM OP M(X) GM(X) 2*GM(X) F... 2*F... GK... 2*GK... 2 F650H lbs. 14 lbs. 2.5 F665H lbs. 24 lbs. 161 lbs. 32 lbs. 3 F680H lbs. 25 lbs. 4 F6100H lbs. 2 F750H lbs. 46 lbs. 2.5 F765H lbs. 65 lbs. 56 lbs. 3 F780H lbs. 74 lbs. 4 F7100H lbs. 124 lbs. Max GPM = Maximum US gallons of water (gpm) per minute, at room temperature, that will flow through the fully open valve without exceeding design velocity limits. OP = lose-off Pressure stated in psi. This is the maximum differential pressure the valve will close-off against while maintaining a bubble tight seal. ll SY series actuators are NEM 4X rated and include 2 auxiliary switches and a heater. 4

5 H Series utterfly Valves Industrial ctuation (verage ssembly Weights) UNERUT MOELS 3-WY 2-WY TUTOR NON-SPRING RETURN Size Valve Max GPM OP SY1 SY2 SY3 SY4 2 F650HU lbs. 2.5 F665HU lbs. 3 F680HU lbs. 4 F6100HU lbs. 5 F6125HU lbs. 6 F6150HU lbs. 8 F6200HU lbs. 10 F6250HU lbs. 12 F6300HU lbs. 2 F750HU lbs 2.5 F765HU lbs. 3 F780HU lbs. 4 F7100HU lbs. 5 F7125HU lbs. 6 F7150HU lbs. 8 F7200HU lbs. 10 F7250HU lbs. 12 F7300HU lbs. FULL RTE MOELS 3-WY 2-WY TUTOR NON-SPRING RETURN Size Valve Max GPM OP SY2 SY3 SY4 SY6 SY7 SY8 SY10 SY12 2 F650H lbs. 2.5 F665H lbs. 3 F680H lbs. 4 F6100H lbs. 5 F6125H lbs. 6 F6150H lbs. 8 F6200H lbs. 10 F6250H lbs. 12 F6300H lbs. 14 F6350H lbs. 16 F6400H lbs. 18 F6450H lbs. 20 F6500H lbs. 24 F6600H lbs. 30 F6750H lbs. 2 F750H lbs. 2.5 F765H lbs. 3 F780H lbs. 4 F7100H lbs. 5 F7125H lbs. 6 F7150H lbs. 8 F7200H lbs. 10 F7250H lbs. 12 F7300H lbs. 14 F7350H lbs. 16 F7400H lbs. 18 F7450H lbs. 20 F7500H lbs. 24 F7600H lbs. Max GPM = Maximum US gallons of water (gpm) per minute, at room temperature, that will flow through the fully open valve without exceeding design velocity limits. OP = lose-off Pressure stated in psi. This is the maximum differential pressure the valve will close-off against while maintaining a bubble tight seal. ll SY series actuators are NEM 4X rated and include 2 auxiliary switches and a heater. 5

6 utterfly Valve Selection-Velocity hart HU/H/VI Series Valves MSTER OMMON OMMON MSTER SLVE MSTER 163 OMMON SLVE SLVE ONFIG OE X10 ON/OFF OR MSTER VLVE IS OPEN MSTER FIL NON-FIL ONFIG OE X20 ON/OFF OR MO@2V MSTER VLVE IS OPEN MSTER FIL NON-FIL ONFIG OE X30 ON/OFF OR MO@2V MSTER VLVE IS OPEN MSTER FIL NON-FIL X11 OPEN OPEN X21 OPEN OPEN X31 OPEN OPEN X12 OPEN LOSE X22 OPEN LOSE X32 OPEN LOSE X13 LOSE NON-FIL X23 LOSE NON-FIL X33 LOSE NON-FIL X14 LOSE OPEN X24 LOSE OPEN X34 LOSE OPEN X15 LOSE LOSE X25 LOSE LOSE X35 LOSE LOSE X Specifies i-irectional Flow apability Notes: 1. Slave Valve operates inversely of the Master Valve. 2. The Master Valve is always located on the run. 3. The Slave Valve may also have an actuator if required (irect oupled). 4. On/Off actuator normal position is a function of field logic. 5. Proportional actuator normal position is a function of the W/W 6. ll 3-way assemblies are designed for 90 degree actuator rotation. Flow in Std Weight Pipe (Fluid Velocity in GPM). Use with Resilient Seat F Valves. Size 2 FPS 4 FPS 6 FPS 8 FPS 10 FPS 12 FPS 14 FPS 16 FPS ½ It is not recommended to exceed 12 feet per second through resilient seat butterfl y valves. Velocities greater than 12 fps may damage the valve liner and disc. If the maximum recommended velocity is exceeded, the valve may be damaged and/or the torque increased potentially exceeding the actuators capacity. 6

7 F6 Series, 2-Way, HU utterfly Valve Resilient Seat, 304 Stainless isc 50 psi bubble tight shut-off Long stem design allows for 2 insulation Valve face-to-face dimensions comply with PI 609 & MSS-SP-67 ompletely assembled and tested, ready for installation pplication These valves are designed to meet the needs of HV and commercial applications requiring bubble tight shut-off for liquids. Typical applications include chiller isolation, cooling tower isolation, change-over systems, large air handler coil control, bypass and process control applications. The large v values provide for an economical control valve solution for larger flow applications. esigned for use in Victaulic piping systems when mated to Victaulic 41 series flange nipples. Jobsite Note Valves should be stored in a weather protected area prior to construction. omplete installation recommendations can be found in elimo s Installation and Maintenance Instructions for F6 HU utterfl y Valves. Technical ata Service chilled, hot water, 60% glycol Flow characteristic modifi ed equal percentage ontrollable flow range 82 Sizes 2 to 12 Type of end fi tting for use with NSI lass 125/150 fl anges Materials ody ductile iron STM 536 ody fi nish epoxy powder coated isc 304 stainless steel Seat EPM Shaft 416 stainless steel O-ring EPM ushings RPTFE Media temperature range -22 F to 250 F [-30 to 120 ] ody pressure rating SME/NSI lass 125 lose-off pressure 50 psi Rangeability 10:1 (for 30 to 70 range) Maximum velocity 12 FPS Leakage bubble tight Valve Nominal Size Type Suitable ctuators v v IN N [mm] 2-way Spring Non-Spring F650HU ½ 65 F665HU F680HU F6100HU F6125HU F6150HU F6200HU F6250HU F6300HU F Series M Series GM Series R SY Series Electronic Fail-Safe KR GK Series MO ON/OFF Valve Size v F650HU F665HU 2½ F680HU F6100HU F6125HU F6150HU F6200HU F6250HU F6300HU

8 F6 Series, 2-Way, HU utterfly Valve Resilient Seat, 304 Stainless isc Maximum imensions (Inches) Valve Size v 90 v 60 (Max) H No. of Holes Lug olt ctuator lose-off (PSI) /8-11 UN 50 F665HU 2½ /8-11 UN F 50 F680HU /8-11 UN 50 F6100HU /8-11 UN 50 2*F F6125HU /4-10 UN 50 F6100HU /8-11 UN 50 GK F6125HU /4-10 UN 50 F6150HU /4-10 UN 2*GK 50 F650HU /8-11 UN F665HU 2½ /8-11 UN M 50 F680HU /8-11 UN 50 F6100HU /8-11 UN 50 GM F6125HU /4-10 UN 50 F6150HU /4-10 UN 2*GM/GK 50 F6150HU /4-10 UN R/KR 50 F650HU /8-11 UN 50 F665HU 2½ /8-11 UN SY F680HU /8-11 UN 50 F6100HU /8-11 UN 50 F6125HU /4-10 UN SY F6150HU /4-10 UN 50 F6200HU /4-10 UN 50 SY3... F6250HU /8-9 UN 50 F6300HU /8-9 UN SY Spring Return Electronic Fail-Safe Non-Spring Return imension is compressed, add.125 for relaxed state. F, M and GM maximum actuator ambient temperature is 122 F. SY maximum actuator ambient temperature is 150 F. Model SY1 does not have handwheel - override is via 8mm wrench on bottom side of actuator. pplication Notes 1. Valves are rated at 50 psi differential pressure in the closed position. 2. Valves are furnished with lugs tapped for use with NSI lass 125/150 fl anges. Installation fl anges and hardware are not included way assemblies are furnished assembled and tested, ready for installation. 4. imension allows for actuator removal without the need to remove the valve from the pipe. 5. Weather shields are available, dimensional data upon request. 6. ual actuated valves have actuators mounted on a common valve shaft. 7. elimo SY Series actuators are NEM 4X rated. imensions F2WUIM Flow Pattern % OF MXIMUM FLOW % OF VLVE OPENING 100 8

9 F7 Series 3-Way, HU utterfly Valve Resilient Seat, 304 Stainless isc 50 psi bubble tight shut-off Long stem design allows for 2 insulation Valve face-to-face dimensions comply with PI 609 & MSS-SP-67 ompletely assembled and tested, ready for installation Tees comply with SME/NSI 16.1 lass 125 fl anges pplication These valves are designed to meet the needs of HV and commercial applications requiring bubble tight shut off for liquids. Typical applications include chiller isolation, cooling tower isolation, change-over systems, large air handler coil control, bypass and process control applications. The large v values provide for an economical control valve solution for larger flow applications. esigned for use in Victaulic piping systems when mated to Victaulic 41 series flange nipples. Jobsite Note Valves should be stored in a weather protected area prior to construction. omplete installation recommendations can be found in elimo s Installation and Maintenance Instructions for F7 HU utterfl y Valves. Technical ata Service chilled, hot water, 60% glycol Flow characteristic modifi ed linear ontrollable fl ow range 82 Sizes 2 to 12 Type of end fi tting for use with NSI 125/150 fl anges Materials ody ductile iron STM 536 ody fi nish epoxy powder fi nish isc 304 stainless steel Seat EPM standard Shaft 416 stainless steel O-ring EPM ushings RPTFE Media temperature range -22 F to 250 F [-30 to 120 ] ody pressure rating SME/NSI lass 125 lose-off pressure 50 psi Rangeability 10:1 (for 30 to 70 range) Maximum velocity 12 FPS Leakage bubble tight Nominal Size Type Suitable ctuators v v IN N [mm] 3-way Spring Non-Spring F750HU ½ 65 F765HU F780HU F7100HU F7125HU F7150HU F7200HU F7250HU F7300HU F Series M GM Series SY Series Electronic Fail-Safe MO ON/OFF Valve Size v F750HU F765HU 2½ F780HU F7100HU F7125HU F7150HU F7200HU F7250HU F7300HU GK Series 9

10 0 F7 Series 3-Way, HU utterfly Valve Resilient Seat, 304 Stainless isc Maximum imensions (Inches) Valve Size v 90 (Max) H No. of Holes Lug olt ctuator lose-off (PSI) F750HU /8-11 UN F 50 F765HU 2½ /8-11 UN 50 2*F F780HU /8-11 UN 50 F780HU /8-11 UN GK 50 F7100HU /8-11 UN 50 F7125HU /4-10 UN 2*GK 50 F7150HU /4-10 UN 50 F750HU /8-11 UN 50 R F765HU 2½ /8-11 UN 50 F780HU /8-11 UN GM 50 F7100HU /8-11 UN 50 F7125HU /4-10 UN 2*GM 50 F7150HU /4-10 UN 50 F750HU /8-11 UN 50 SY1 F765HU 2½ /8-11 UN 50 F780HU /8-11 UN 50 F7100HU /8-11 UN 50 SY2 F7125HU /4-10 UN 50 F7150HU /4-10 UN 50 F7200HU /4-10 UN SY3 50 F7250HU /8-9 UN 50 SY4 F7300HU /8-9 UN 50 Spring Return Electronic Fail-Safe Non-Spring Return F maximum actuator ambient temperature is 122 F. SY... maximum actuator ambient temperature is 150 F. Model SY1 does not have hand wheel-override is via 8mm wrench on bottom side of actuator. imensions HS WGP15 pplication Notes 1. Valves are rated at 50 psi differential pressure in the closed position. 2. Valves are furnished with lugs tapped for use with NSI lass 125/150 fl anges. Installation fl anges and hardware are not included way assemblies are furnished assembled and tested, ready for installation. ll 3-way assemblies require the customer to specify the 3-way confi guration prior to order entry to guarantee correct placement of valves and actuators on the assembly. 4. imension allows for actuator removal without the need to remove the valve from the pipe. 5. Weather shields are available, dimensional data upon request. 6. ual actuated valves have single actuators mounted on each valve shaft. 7. olts supplied are for shipping purposes only. Upon installation replace with an appropriate SE grade 5 or better hardware. 8. elimo SY Series actuators are NEM 4X rated. S 10

11 F6 Series 2-Way, H utterfly Valve Resilient Seat, 304 Stainless isc 200 psi (2 to 12 ) and 150 psi (14-30 ) bubble tight shut-off Long stem design allows for 2 insulation Valve face-to-face dimensions comply with PI 609 & MSS-SP-67 ompletely assembled and tested, ready for installation pplication These valves are designed to meet the needs of HV and commercial applications requiring bubble tight shut-off for liquids. Typical applications include chiller isolation, cooling tower isolation, change-over systems, large air handler coil control, bypass and process control applications. The large v values provide for an economical control valve solution for larger flow applications. esigned for use in Victaulic piping systems when mated to Victaulic 41 series flange nipples. Jobsite Note Valves should be stored in a weather protected area prior to construction. omplete installation recommendations can be found in elimo s Installation and Maintenance Instructions for F6 H utterfl y Valves. Technical ata Service chilled, hot water, 60% glycol Flow characteristic modifi ed equal percentage ontrollable flow range 82 Sizes 2 to 30 Type of end fi tting for use with NSI 125/150 fl anges Materials ody ductile iron STM 536 ody fi nish epoxy powder coated isc 304 stainless steel Seat EPM standard Shaft 416 stainless steel O-ring EPM ushings RPTFE Media temperature range -22 F to 250 F [-30 to 120 ] ody pressure rating SME/NSI lass 125/150 lose-off pressure 200 psi (2-12 ), 150 psi (14-30 ) Rangeability 10:1 (for 30 to 70 range) Maximum velocity 12 FPS Leakage bubble tight Valve Nominal Size Type Suitable ctuators v v N Electronic IN [mm] 2-way Spring Non-Spring Fail-Safe F650H ½ 65 F665H F680H F6100H F6125H F6150H F6200H F6250H F6300H F6350H F6400H F6450H F6500H F6600H F6750H MO ON/OFF Valve Size v F650H F665H 2-1/ F680H F6100H F6125H F6150H F6200H F6250H F6300H F6350H F6400H F6450H F6500H F6600H F6750H F Series M GM R SY Series KR GK 11

12 F6 Series 2-Way, H utterfly Valve Resilient Seat, 304 Stainless isc Maximum imensions (Inches) Valve Size v 90 v 60 (Max) H No. of Holes Lug olt ctuator lose-off (PSI) /8-11 UN F 200 F665H 2½ /8-11 UN 200 2*F F680H /8-11 UN 200 Spring Return F6100H /8-11 UN 2*GK 200 F650H /8-11UN 200 M(X) F665H 2½ /8-11UN 200 F680H /8-11 UN GM(X) 200 F6100H /8-11 UN 2*GM(X) 200 F6100H /8-11 UN R/KR 200 F650H /8-11 UN 200 F665H 2½ /8-11 UN 200 F680H /8-11 UN SY2 200 F6100H /8-11 UN 200 F6125H /4-10 UN 200 F6150H /4-10 UN SY3 200 F6200H /4-10 UN 200 F6250H /8-9 UN SY4 200 F6300H /8-9 UN 200 F6350H UN SY5 150 F6400H UN SY6 150 F6450H /8-7 UN 150 SY8 F6500H /8-7 UN 150 F6600H /4-7 UN SY F6750H /4-7 UN SY Electronic Fail-Safe Non-Spring Return imension is compressed, add.125 for relaxed state. SY6 and larger available in 110/220 V versions only. F, M and GM maximum actuator ambient temperature is 122 F. SY... maximum actuator ambient temperature is 150 F. pplication Notes 1. Valves are rated at 200 psi differential pressure in the closed position (SY psi 14 +). 2. Valves are furnished with lugs tapped for use with NSI lass 125/150 fl anges. Installation fl anges and hardware are not included way assemblies are furnished assembled and tested, ready for installation. 4. imension allows for actuator removal without the need to remove the valve from the pipe. 5. Weather shields are available, dimensional data upon request. 6. ual actuated valves have actuators mounted on a common valve shaft. 7. elimo SY Series actuators are NEM 4X rated. Flow Pattern % OF MXIMUM FLOW imensions F2WUIM % OF VLVE OPENING

13 F7 Series 3-Way, H utterfly Valve Resilient Seat, 304 Stainless isc 200 psi (2 to 12 ) and 150 psi (14-30 ) bubble tight shut-off Long stem design allows for 2 insulation Valve face-to-face dimensions comply with PI 609 & MSS-SP-67 ompletely assembled and tested, ready for installation Tees comply with SME/NSI 16.1 lass 125 fl anges pplication These valves are designed to meet the needs of HV and commercial applications requiring bubble tight shut off for liquids. Typical applications include chiller isolation, cooling tower isolation, change-over systems, large air handler coil control, bypass and process control applications. The large v values provide for an economical control valve solution for larger flow applications. esigned for use in Victaulic piping systems when mated to Victaulic 41 series fl ange nipples. Fail safe operation is possible with NSV-SY series battery backup systems. Jobsite Note Valves should be stored in a weather protected area prior to construction. omplete installation recommendations can be found in elimo s Installation and Maintenance Instructions for F7 H utterfl y Valves. Technical ata Service chilled, hot water, 60% glycol Flow characteristic modifi ed linear ontrollable fl ow range 82 Sizes 2 to 24 Type of end fi tting for use with NSI 125/150 fl anges Materials: ody ductile iron STM 536 ody fi nish epoxy powder coated isc 304 stainless steel Seat EPM standard Shaft 416 stainless steel O-ring EPM ushings RPTFE Media temperature range -22 F to 250 F [-30 to 120 ] ody pressure rating SME/NSI lass 125/150 lose-off pressure 200 psi (2-12 ), 150 psi (14-24 ) Rangeability 10:1 (for 30 to 70 range) Maximum Velocity 12 FPS Nominal Size Type Suitable ctuators v v IN N [mm] 2-way Spring Non-Spring F750H ½ 65 F765H F780H F7100H F7125H F7150H F7200H F7250H F7300H F7350H F7400H F7450H F7500H F7600H F Series M GM SY Series Electronic Fail-Safe MO ON/OFF Valve Size v F750H F765H 2½ F780H F7100H F7125H F7150H F7200H F7250H F7300H F7350H F7400H F7450H F7500H F7600H GK 13

14 F7 Series 3-Way, H utterfly Valve Resilient Seat, 304 Stainless isc Maximum imensions (Inches) Valve Size v 90 (Max) H No. of Holes Lug olt ctuator lose-off (PSI) F750H /8-11 UN F 200 F765H 2½ /8-11 UN 2*F 200 F780H /8-11 UN 2*GM/GK 200 F750H /8-11 UN 200 F765H 2½ /8-11 UN 200 SY2 F780H /8-11 UN 200 F7100H /8-11 UN 200 F7125H /4-10 UN 200 SY3 F7150H /4-10 UN 200 F7200H /4-10 UN 200 SY4 F7250H /8-9 UN 200 F7300H /8-9 UN SY5 200 F7350H UN SY6 150 F7400H UN SY7 150 F7450H /8-7 UN 150 SY9 F7500H /8-7 UN 150 F7600H /4-7 UN SY Spring Return Electronic Fail-Safe Non-Spring Return F maximum actuator ambient temperature is 122 F. SY... maximum actuator ambient temperature is 150 F. SY6 and larger available in 110/220 V versions only. pplication Notes 1. Valves are rated at 200 psi differential pressure in the closed position. 2. Valves are furnished with lugs tapped for use with NSI lass 125/150 fl anges. Installation fl anges and hardware are not included way assemblies are furnished assembled and tested, ready for installation. ll 3-way assemblies require the customer to specify the 3-way confi guration prior to order entry to guarantee correct placement of valves and actuators on the assembly. 4. imension allows for actuator removal without the need to remove the valve from the pipe. 5. elimo SY Series actuators are NEM 4X rated. 5. Weather shields are available, dimensional data upon request. 6. ual actuated valves have single actuators mounted on each valve shaft. 7. olts supplied are for shipping purposes only. Upon installation replace with an appropriate SE grade 5 or better hardware. 163 Note: For tee confi guration, please refer to page 4. 3-Way onfi guration odes MSTER ONFIG OE X10 X11 X12 X13 X14 ON/OFF OR MO@2V MSTER VLVE IS OPEN OPEN OPEN LOSE LOSE SLVE MSTER FIL NON-FIL OPEN LOSE NON-FIL OPEN X15 LOSE LOSE X Specifies i-irectional Flow apability OMMON ONFIG OE X20 X21 X22 X23 X24 X25 OMMON SLVE ON/OFF OR MO@2V MSTER VLVE IS OPEN OPEN OPEN LOSE LOSE LOSE MSTER FIL NON-FIL OPEN LOSE NON-FIL OPEN LOSE MSTER SLVE ONFIG OE X30 X31 X32 X33 X34 X35 OMMON ON/OFF OR MO@2V MSTER VLVE IS OPEN OPEN OPEN LOSE LOSE LOSE imensions MSTER FIL NON-FIL OPEN LOSE NON-FIL OPEN LOSE MSTER NOTES 1. Slave Valve operates inversely of the Master Valve. 2. The Master Valve is always located on the run. 3. The Slave Valve may also have an actuator if required (irect oupled). 4. On/Off actuator normal position is a function of fi eld logic. 5. Proportional actuator normal position is a function of the W/W switch. 6. ll 3-way assemblies are designed for 90 degree actuator rotation. ORERING INFORMTION Please note that H series F valves over 18 and LL sizes 3-way tee assemblies ordered with onfiguration odes are special order/custom built and are NOT returnable. HS WG11 14

15 Features and enefits VI Victaulic utterfly Valves elimo VI.. Series Victaulic utterfl y Valves are designed for pressure ranging from vacuum to 300psi and for dead end services Valve esign Features The valve features a patented seat design that assures full 360 sealing. The pressure enhanced seat compresses to form a larger seating area as the pressure increases. The seat design also contributes to low breakaway torque of the valve. Valves have EPM seats that are L classifi ed to NSI/NSF 61. The disc is ductile iron, conforming to STM -536, grade with electrolysis nickel coating conforming to STM Stem is 416 stainless steel conforming to STM to full working pressure. ll Vitaulic valves are supplied in grooved style body design. RIVE HU esigned to accept nearly all types of actuation. ISO 5211 MOUNTING FLNGE ccepts ISO standard actuators. 2-8 / mm are fl ange size F / mm are fl ange size F10. STEM SELS Prevents leakage of media. GROOVE EN OY Reduces the weight of the valve and makes it easier to install. UPPER N LOWER STEM ERINGS Helps maintain constant low torque values for the life of the valve. THERML RRIER Reduces condensation on gear operators when installed in chilled water applications. SEL RTRIGE Patented seal cartridge houses stem seals. STEM lowout proof design utilizing stainless steel. RETNGULR RIVE Positive rectangular drive eliminates fastners in the flow stream. esign prevents replacement errors. SET Patented pressure enhanced rubber seat design. IS Electroless nickel coated ductile iron. Optional: luminum ronze Stainless Steel 15

16 F6 Series 2-Way, Victaulic utterfly Valve 200 psi (2 to 12 ) bubble tight shut-off Long stem design allows for 2 insulation ompletely assembled and tested, ready for installation pplication These valves are designed to meet the needs of HV and commercial applications requiring bubble tight shut-off for liquids. Typical applications include chiller isolation, cooling tower isolation, change-over systems, large air handler coil control, bypass and process control applications. The large v values provide for an economical control valve solution for larger flow applications. Jobsite Note Valves should be stored in a weather protected area prior to construction. 2-way Suitable ctuators Technical ata Service chilled, hot water, 60% glycol Flow characteristic modifi ed equal percentage ontrollable fl ow range 82 Sizes 2 to 12 Type of end fi tting grooved NSI/WW (606) Valve materials* ody ductile iron STM 536, grade ody fi nish black alkyd enamel isc electroless nickel coated ductile iron Seat EPM Shaft 416 stainless steel earing fi berglass with TFE lining ody pressure rating 300 psi Media temperature range -30 F to 250 F [-34 to 120 ] Rangeability 100:1 Maximum close-off pressure 200 psi Maximum velocity 20 FPS *VI 300 Masterseal as manufactured by Victaulic ompany Valve Size v F650VI F665VI 2-1/ F680VI F6100VI F6125VI F6150VI F6200VI F6250VI F6300VI v 90 v 60 IN Valve Nominal Size N [mm] Type 2-way F650VI ½ 65 F665VI F680VI F6100VI F6125VI F6150VI F6200VI F6250VI F6300VI Spring Return F Series M Non-Spring Return GM Series SY Series Electronic Fail-Safe GK Series 16

17 6.393 [162.38] F6 Series 2-Way, Victaulic utterfly Valve Maximum imensions (Inches) Valve Size v 90 (Max) (Max) (Max) (Max) ctuator lose-off (PSI) F650VI F F665VI 2½ F665VI 2½ *F F680VI F665VI 2½ GK F680VI F6100VI *GK 200 F650VI M... F665VI 2½ F665VI 2½ GM... F680VI F6100VI *GM 200 F650VI F665VI 2½ SY F680VI F680VI SY2... F6100VI F6125VI /200 SY2 / SY3 F6150VI /200 F6200VI SY4 200 F6250VI SY4 / SY5 50/200 F6300VI SY6 200 Spring Return Electronic Fail-Safe Non-Spring Return SY6 and larger available in 110/220 V versions only. SY... maximum actuator ambient temperature is 150 F. pplication Notes 1. Valves are rated at 200 psi differential pressure in the closed position 2. 2-way assemblies are furnished assembled and tested, ready for installation. 3. imension allows for actuator removal without the need to remove the valve from the pipe. 4. elimo SY Series actuators are NEM 4X rated. 5. Provide support for the actuator if it is mounted at any angle other than 90 vertical. 6. Installer is to use rigid type couplings for connecting the valve to the piping. Flow Rate (GPM) Pressure rop - psi /60.3 mm 2 1/2 /73.0 mm & 76.1 mm 3 /88.9 mm 5 /141.3 mm, mm & mm 4 /114.3 mm & mm 6 /168.3 mm &165.1 mm & mm 8 /219.1 mm 10 /273.0 mm 12 /323.9 mm imensions [47.05] [217.25] [97.99] 4 [101.6]

18 F7 Series 3-Way, Victaulic utterfly Valve 200 psi (2 to 12 ) bubble tight shut-off Long stem design allows for 2 insulation ompletely assembled and tested, ready for installation pplication These valves are designed to meet the needs of HV and commercial applications requiring bubble tight shut-off for liquids. Typical applications include chiller isolation, cooling tower isolation, change-over systems, large air handler coil control, bypass and process control applications. The large v values provide for an economical control valve solution for larger fl ow applications. Jobsite Note Valves should be stored in a weather protected area prior to construction. 3-way Suitable ctuators Technical ata Service chilled, hot water, 60% glycol Flow characteristic modifi ed equal percentage ontrollable fl ow range 82 Sizes 2 to 12 Type of end fi tting grooved NSI/WW (606) Valve materials* ody ductile iron STM 536, grade ody fi nish black alkyd enamel isc electroless nickel coated ductile iron Seat EPM Shaft 416 stainless steel earing fi berglass with TFE lining ody pressure rating 300 psi Media temperature range -30 F to 250 F [-34 to 120 ] Rangeability 100:1 Maximum close-off pressure 200 psi Maximum velocity 20 FPS *VI 300 Masterseal as manufactured by Victaulic ompany Valve Nominal Size Valve Size v F750VI F765VI 2½ F780VI F7100VI F7125VI F7150VI F7200VI F7250VI F7300VI v 90 v 60 IN N [mm] Type 2-way F750VI ½ 65 F765VI F780VI F7100VI F7125VI F7150VI F7200VI F7250VI F7300VI Spring Return F Series M Non-Spring Return GM Series SY Series Electronic Fail-Safe GK Series 18

19 F7 Series 3-Way, Victaulic utterfly Valve Maximum imensions (Inches) Valve Size v 90 (Max) (Max) (Max) (Max) ctuator lose-off (PSI) F750VI F 50 F750VI *F F765VI 2½ F750VI GK F765VI 2½ F780VI *GK 50 F750VI M F750VI GM... F765VI 2½ F765VI 2½ *GM F780VI F750VI SY1... F765VI 2½ F765VI 2½ F780VI SY F7100VI F7125VI SY3... F7150VI F7150VI SY4... F7200VI F7250VI SY F7250VI SY7... F7300VI Spring Return Electronic Fail-Safe Non-Spring Return SY6 and larger available in 110/220 V versions only. SY... maximum actuator ambient temperature is 150 F. pplication Notes 1. Valves are rated at 200 psi differential pressure in the closed position 2. 2-way assemblies are furnished assembled and tested, ready for installation. 3. imension allows for actuator removal without the need to remove the valve from the pipe. 4. elimo SY Series actuators are NEM 4X rated. 5. Provide support for the actuator if it is mounted at any angle other than 90 vertical. 6. Installer is to use rigid type couplings for connecting the valve to the piping. Flow Rate (GPM) Pressure rop - psi /60.3 mm 2 1/2 /73.0 mm & 76.1 mm 3 /88.9 mm 5 /141.3 mm, mm & mm 4 /114.3 mm & mm 6 /168.3 mm &165.1 mm & mm 8 /219.1 mm 10 /273.0 mm 12 /323.9 mm imensions [192] [213.51] [115.6] [92.12] [97.99] [92.12]

20 Features and enefits SHP Series High Performance utterfly Valves elimo SHP... Series utterfl y Valves are designed for use in NSI lass 150 and NSI lass 300 piping systems and are supplied in standard lug style body designs. Valve esign Features Unique seat and disc design provides i-irectional bubble tight shutoff at rated pressure/temperatures The Soft Seat design creates a self-energized seal in vacuum-to-low pressure applications Under high pressure conditions, the seat is also designed to permit, confi ne and direct movement of the seat against the disc edge, up to the full NSI lass 150 or 300 old Working Pressures The Soft Seat is designed for high services with minimal wear and low torque Seat replacement is a simple operation, requiring no special tools Valve ody is Full Lug type cast in arbon Steel isc is cast in F8M Stainless Steel Shaft is 17-4pH Stainless for superior strength Soft Seat is RPTFE for increased wear resistance and low torque Top Mounted Gland Flange easily accessible without removing actuator or mounting brackets KEY Square key valve-to-operator connection provides an externally controlled failure point upon over-torquing. GLN FLNGE pplies load against packing gland to prevent external leakage. Fully adjustable. PKING hevron design TFE prevents external leakage out valve neck to full NSI hydrostatic shell test pressures (150% of.w.p.). WEGE RING Stainless steel band wedged between valve body and retainer ring by set screws to lock seat and retainer ring in position on valve sizes 2 through 30. Socket head cap screws are used on valve sizes 36 and larger. SET SREWS one point screws force wedge ring outward to lock seat retainer in position on valve sizes 2 through 30. Socket head cap screws are used on valve sizes 36 and larger. OVERTRVEL STOP Prevents disc from rotating into wrong quadrant. SOFT-SET Patented bidirectional seat with encapsulated elastomeric o-ring core for resiliency. ommon seat materials include TFE, RTFE and UHMWPE. LOW OUT PROOF SHFT Solid shaft provides alignment and rigid support for disc. PKING GLN Separate part from gland fl ange, preventing uneven load distribution against packing. ERINGS oth above and below the disc, bearings are of composite design: PTFE bonded to epoxy-glass fi lament wound ring. Used to align shaft, with high capacity, low wear and low friction coeffi cient. IS SPERS isc is centered by use of thrust spacers around shaft in sizes 2 to 5. isc position stops or thrust bolt arrangements are used for larger valve sizes. WEGE PINS Provide positive mechanical attachment of disc to shaft. OY NSI design in either wafer or lug configuration. IS 360 uninterrupted spherical edge for sealing. Profile is designed for maximum fl ow and equal percentage control. RETINER RING Retains seat in valve. Standard surface fi nish is 125 to 200 RH and is compatible with both standard gaskets and spiral wound gasket designs. Outside diameter is recessed within gasket sealing surface to prevent external leakage. 20

21 SHP Series utterfly Valves verage ssembly Weights NSI way 3-way TUTOR NON-SPRING RETURN SPRING RETURN ELETRONI FIL-SFE Size Valve Max GPM OP GM(X) 2*GM(X) 2*F GK 2*GK 2 F SHP lbs. 2 F SHP lbs. 19 lbs. 2½ F SHP lbs. 2½ F SHP lbs 19 lbs. 3 F SHP lbs. 3 F SHP lbs. 21 lbs. 4 F SHP lbs. 33 lbs. 4 F SHP lbs. 42 lbs 2 F SHP lbs. 69 lbs. 2½ F SHP lbs. 80 lbs. 3 F SHP lbs. 90 lbs. 4 F SHP lbs. 139 lbs. NSI way 3-way TUTOR NON-SPRING RETURN SPRING RETURN ELETRONI FIL-SFE Size Valve Max GPM OP GM(X) 2*GM(X) 2*F GK 2*GK 2 F SHP lbs. 2 F SHP lbs. 19 lbs. 2½ F SHP lbs. 2½ F SHP lbs. 19 lbs. 3 F SHP lbs. 3 F SHP lbs. 25 lbs. 4 F SHP lbs. 32 lbs. 4 F SHP lbs. 2 F SHP lbs. 94 lbs. 2½ F SHP lbs. 114 lbs. 3 F SHP lbs. 136 lbs. 4 F SHP lbs. 193 lbs. Max GPM = Maximum US gallons of water (gpm) per minute, at room temperature, that will flow through the fully open valve without exceeding design velocity limits. OP = lose-off Pressure stated in psi. This is the maximum differential pressure the valve will close-off against while maintaining a bubble tight seal. ll SY series actuators are NEM 4X rated and include 2 auxiliary switches and a heater. 21

22 SHP Series utterfly Valves with Industrial ctuation NSI way 3-way TUTOR NON-SPRING RETURN Size Valve Model Max GPM OP SY2-110 SY3-110 SY4-110 SY5-110 SY7-110 SY8-110 SY9-110 SY SY SY F SHP lbs. 2½ F SHP lbs. 3 F SHP lbs. 4 F SHP lbs. 5 F SHP lbs. 6 F SHP lbs. 8 F SHP lbs. 8 F SHP lbs. 10 F SHP lbs. 12 F SHP lbs. 12 F SHP lbs. 14 F SHP lbs. 14 F SHP lbs. 16 F SHP lbs. 18 F SHP lbs. 18 F SHP lbs. 20 F SHP lbs. 20 F SHP lbs. 24 F SHP lbs. 30 F SHP lbs. 2 F SHP lbs. 2½ F SHP lbs. 3 F SHP lbs. 4 F SHP lbs. 5 F SHP lbs. 6 F SHP lbs. 8 F SHP lbs. 10 F SHP lbs. 10 F SHP lbs. 12 F SHP lbs. 12 F SHP lbs. 14 F SHP lbs. 16 F SHP lbs lbs. 18 F SHP lbs. 18 F SHP lbs. 20 F SHP lbs. 20 F SHP lbs. 24 F SHP lbs. Max GPM = Maximum US gallons of water (gpm) per minute, at room temperature, that will flow through the fully open valve without exceeding design velocity limits. OP = lose-off Pressure stated in psi. This is the maximum differential pressure the valve will close-off against while maintaining a bubble tight seal. ll SY series actuators are NEM 4X rated and include 2 auxiliary switches and a heater. 22

23 SHP Series utterfly Valves with Industrial ctuation verage ssembly Weights NSI way TUTOR NON-SPRING RETURN Size Valve Model Max GPM OP SY2-110 SY3-110 SY4-110 SY5-110 SY7-110 SY8-110 SY9-110 SY SY F SHP lbs. 2½ F SHP lbs. 3 F SHP lbs. 4 F SHP lbs. 5 F SHP lbs. 5 F SHP lbs. 6 F SHP lbs. 6 F SHP lbs. 8 F SHP lbs. 8 F SHP lbs. 8 F SHP lbs. 10 F SHP lbs. 10 F SHP lbs. 10 F SHP lbs. 12 F SHP lbs. 12 F SHP lbs. 12 F SHP lbs. 14 F SHP lbs. 14 F SHP lbs. 14 F SHP lbs. 16 F SHP lbs. 16 F SHP lbs. 16 F SHP lbs. 16 F SHP lbs. 18 F SHP lbs. 18 F SHP lbs. 18 F SHP lbs. 20 F SHP lbs. 20 F SHP lbs. 24 F SHP lbs. Max GPM = Maximum US gallons of water (gpm) per minute, at room temperature, that will flow through the fully open valve without exceeding design velocity limits. OP = lose-off Pressure stated in psi. This is the maximum differential pressure the valve will close-off against while maintaining a bubble tight seal. ll SY series actuators are NEM 4X rated and include 2 auxiliary switches and a heater. 23

24 SHP Series utterfly Valves with Industrial ctuation verage ssembly Weights NSI way TUTOR NON-SPRING RETURN Size Valve Model Max GPM OP SY2-110 SY3-110 SY4-110 SY5-110 SY7-110 SY8-110 SY9-110 SY SY SY F SHP lbs. 2 F SHP lbs 2½ F SHP lbs. 2½ F SHP lbs. 3 F SHP lbs. 3 F SHP lbs. 4 F SHP lbs. 4 F SHP lbs. 5 F SHP lbs. 5 F SHP lbs. 6 F SHP lbs. 6 F SHP lbs. 8 F SHP lbs. 8 F SHP lbs. 8 F SHP lbs. 10 F SHP lbs. 10 F SHP lbs. 10 F SHP lbs. 12 F SHP lbs. 12 F SHP lbs. 12 F SHP lbs. 14 F SHP lbs. 14 F SHP lbs. 14 F SHP lbs. 16 F SHP lbs. 16 F SHP lbs. 16 F SHP lbs. 16 F SHP lbs. 18 F SHP lbs. 18 F SHP lbs. 18 F SHP lbs. 20 F SHP lbs. 24 F SHP lbs. Max GPM = Maximum US gallons of water (gpm) per minute, at room temperature, that will flow through the fully open valve without exceeding design velocity limits. OP = lose-off Pressure stated in psi. This is the maximum differential pressure the valve will close-off against while maintaining a bubble tight seal. ll SY series actuators are NEM 4X rated and include 2 auxiliary switches and a heater. 24

25 utterfly Valve Selection-Velocity hart 150 SHP/300 SHP Series Valves SHP Series Valves are Flow irection Specifi c MIXING MSTER FLOW OMMON OMMON FLOW MSTER SLVE FLOW MSTER 145 OMMON SLVE SLVE IVERTING MSTER FLOW OMMON OMMON MSTER SLVE FLOW MSTER OMMON SLVE SLVE ONFIG OE M()10 M()11 M()12 M()13 M()14 ON/OFF OR MO@2V MSTER VLVE IS OPEN OPEN OPEN LOSE LOSE MSTER FIL NON-FIL OPEN LOSE NON-FIL OPEN M()15 LOSE LOSE M Specifies MIXING, Specifies IVERTING ONFIG OE M()20 M()21 M()22 M()23 M()24 M()25 Notes: 1. Slave Valve operates inversely of the Master Valve. 2. The Master Valve is always located on the run. 3. The Slave Valve may also have an actuator if required (irect oupled). ON/OFF OR MO@2V MSTER VLVE IS OPEN OPEN OPEN LOSE LOSE LOSE MSTER FIL NON-FIL OPEN LOSE NON-FIL OPEN LOSE ONFIG OE M()30 M()31 M()32 M()33 M()34 M()35 ON/OFF OR MO@2V MSTER VLVE IS OPEN OPEN OPEN LOSE LOSE LOSE MSTER FIL NON-FIL OPEN LOSE NON-FIL OPEN LOSE 4. On/Off actuator normal position is a function of field logic. 5. Proportional actuator normal position is a function of the W/W swit 6. ll 3-way assemblies are designed for 90 degree actuator rotation. Flow in Std Weight Pipe (Fluid Velocity in GPM). Use with SHP Series F Valves. SIZE 4 FPS 8 FPS 12 FPS 16 FPS 20 FPS 24 FPS 28 FPS 32 FPS 36 FPS ½ It is not recommended to exceed 32 feet per second through high performance butterfly valves. Velocities greater than 32 fps may damage the valve. 25

26 F6 Series 2-Way, NSI lass 150 utterfly Valve Reinforced Teflon Seat, 316 Stainless isc ubble tight shut-off to NSI lass 150 Standards Long stem design allows for 2 insulation minimum Valve Face-to-face dimensions comply with PI 609 & MSS-SP-68 esigned to be installed between SME/NSI 16.5 Flanges ompletely assembled and tested, ready for installation pplication These valves are designed to meet the needs of HV and ommercial applications requiring positive shut-off for liquids at higher pressures and temperatures. Typical applications include chiller isolation, cooling tower isolation, change-over systems, large air handler coil control, bypass and process control applications. The large v values provide for an economical control valve solution for larger flow applications. Technical ata Service chilled, hot water, 60% glycol, steam to 50 psi Flow characteristic modifi ed equal percentage, unidirectional ontrollable fl ow range 82 Sizes 2" to 24" Type of end fi tting for use with SME/class 125/150 fl ange Materials ody carbon steel full lug isc 316 stainless steel Seat RPTFE Shaft 17-4 PH stainless Gland seal PTFE ushings glass backed PTFE Media temperature range -20 F to 400 F [-30 to 204 ] ody pressure rating NSI lass 150 lose-off pressure 285 psi Rangeability 100:1 (for 30 deg to 70 deg range) Maximum velocity 32 FPS Leakage bubble tight Valve Nominal Size Type Suitable ctuators v v IN 2-way Spring Non-Spring F SHP ½ F SHP F SHP F SHP F SHP F SHP F SHP F SHP F SHP F SHP F SHP F SHP F SHP F SHP F SHP MO ON/OFF Valve Size v F SHP F SHP 2½ F SHP F SHP F SHP F SHP F SHP F SHP F SHP F SHP F SHP F SHP F SHP F SHP F SHP F Series GM Series SY Series 26

27 F6 Series 2-Way, NSI lass 150 utterfly Valve Reinforced Teflon Seat, 316 Stainless isc Maximum imensions (Inches) Valve Size v 90 (Max) H No. of Holes Lug olt ctuator lose-off (PSI) F SHP /8-11 UN 150 F SHP 2½ /8-11 UN 150 2*F F SHP /8-11 UN 150 F SHP /8-11 UN 150 F SHP /8-11 UN 285 F SHP 2½ /8-11 UN 285 GK F SHP /8-11 UN 285 F SHP /8-11 UN 150 F SHP /8-11 UN 2*GK 285 F SHP /8-11 UN 285 F SHP 2½ /8-11 UN 285 GM F SHP /8-11 UN 285 F SHP /8-11 UN 150 F SHP /8-11 UN 2*GM 285 F SHP /8-11 UN 285 F SHP 2½ /8-11 UN 285 F SHP /8-11 UN 285 SY2 F SHP /8-11 UN 285 F SHP /4-10 UN 285 F SHP /4-10 UN 285 F SHP /4-10 UN SY3 150 SY4 285 F SHP /8-9 UN SY4 285 F SHP /8-9 UN SY4 150 SY5 285 SY5 150 F SHP UN 285 SY7 150 F SHP UN SY8 285 F SHP /8-8 UN SY7 150 SY8 285 F SHP /8-8 UN SY8 150 SY F SHP /4-8 UN SY F SHP /4-8 UN SY imension does not include flange gaskets. (2 required per valve) pplication Notes 1. Valves are rated at 285 psi differential pressure in the closed 100 F media temperature. 2. Valves are furnished with lugs tapped for use between NSI lass 125/150 fl anges conforming to NSI 16.5 Standards way assemblies are furnished assembled, calibrated and tested, ready for installation. 4. imension allows for actuator(s) removal without the need to remove the valve from the pipe. 5. Weather shields are available, dimensional data furnished upon request. 6. Flange gaskets (2 required, not provided with valve) MUST be used between valve and NSI fl ange. 7. Flange bolts are not included with the valve. These are furnished by others. imensions H Spring Return Electronic Fail-Safe Non-Spring Return 102 SHP series valves have a preferred flow direction. PreferredFlowrate 27

28 F7 Series 3-Way, NSI lass 150 utterfly Valve Reinforced Teflon Seat, 316 Stainless isc ubble tight shut-off to NSI lass 150 Standards Long stem design allows for 2 insulation minimum Valve Face-to-face dimensions comply with PI 609 & MSS-SP-68 esigned to be installed between SME/NSI 16.5 Flanges ompletely assembled and tested, ready for installation Tees comply with SME/NSI 16.1 lass 125 Flanges pplication These valves are designed to meet the needs of HV and ommercial applications requiring positive shut-off for liquids at higher pressures and temperatures. Typical applications include chiller isolation, cooling tower isolation, change-over systems, large air handler coil control, bypass and process control applications. The large v values provide for an economical control valve solution for larger flow applications. Technical ata Service chilled, hot water, 60% glycol, steam to 50 psi Flow characteristic modifi ed equal percentage, unidirectional ontrollable fl ow range 82 Sizes 2" to 24" Type of end fi tting for use with SME/class 125/150 fl anges Materials ody carbon steel full lug isc 316 stainless steel Seat RPTFE Shaft 17-4 PH stainless Gland seal PTFE ushings glass backed PTFE Media temperature range -20 F to 400 F [-30 to 204 ] ody pressure rating NSI lass 150 lose-off pressure 285 psi Rangeability 100:1 (for 30 deg to 70 deg range) Maximum velocity 32 FPS Leakage bubble tight Valve Nominal Size Type Suitable ctuators IN 3-way Spring Non-Spring Electronic Fail-Safe v 90 v F SHP ½ F SHP F SHP F SHP F SHP F SHP F SHP F SHP F SHP F SHP F SHP F SHP F SHP F SHP MO ON/OFF Valve Size v F SHP F SHP 2½ F SHP F SHP F SHP F SHP F SHP F SHP F SHP F SHP F SHP F SHP F SHP F SHP F Series GM Series SY Series GK Series 28

29 0 F7 Series 3-Way, NSI lass 150 utterfly Valve Reinforced Teflon Seat, 316 Stainless isc Maximum imensions (Inches) Valve Size v 90 (Max) H No. of Holes Lug olt ctuator lose-off (PSI) F SHP /8-11 UN 150 F SHP 2½ /8-11 UN GK 150 F SHP /8-11 UN 150 F SHP /8-11 UN F SHP 2½ /8-11 UN 2*GK 285 F SHP /8-11 UN 285 F SHP /8-11 UN 150 F SHP 2½ /8-11 UN 150 GM F SHP /8-11 UN 150 F SHP /8-11 UN 150 F SHP /8-11 UN 285 F SHP 2½ /8-11 UN 2*GM 285 F SHP /8-11 UN 285 F SHP /8-11 UN 285 F SHP 2½ /8-11 UN 285 SY2 F SHP /8-11 UN 285 F SHP /8-11 UN 285 F SHP /4-10 UN 285 SY3 F SHP /4-10 UN 285 F SHP /4-10 UN SY4 150 F SHP /8-9 UN SY4 150 SY5 285 F SHP /8-9 UN SY5 150 SY7 285 F SHP UN SY7 285 F SHP UN SY7 150 SY9 285 F SHP /8-8 UN SY8 150 SY F SHP /8-8 UN SY9 150 SY F SHP /4-8 UN SY Electronic Fail-Safe Non-Spring Return imensions, and do not include fl ange gaskets. (3 required per valve) pplication Notes 1. Valves are rated at 285 psi differential pressure in the closed 100 F media temperature. 2. Valves are furnished with lugs tapped for use between NSI lass 125/150 fl anges conforming to NSI 16.5 Standards way assemblies are furnished assembled with Tee, calibrated and tested, ready for installation. ll 3-way assemblies require the customer to specify the 3-way confi guration code prior to order entry to guarantee correct placement of valves and actuator(s) on the assembly. 4. imension allows for actuator(s) removal without the need to remove the valve from the pipe. 5. Weather shields are available, dimensional data furnished upon request. 6. ual actuated valves have single actuators mounted on each valve shaft. 7. Flange gaskets (3 required, not provided with valve) MUST be used between valve and NSI fl ange. 8. Flange bolts are not included with the valve. These are furnished by others. Note: For tee confi guration, please refer to page 5. imensions S 104 SHP series valves have a preferred flow direction. PreferredFlowrate 29

30 F6 Series 2-Way, NSI lass 300 utterfly Valve Reinforced Teflon Seat, 316 Stainless isc ubble tight shut-off to NSI lass 300 Standards Long stem design allows for 2 insulation minimum Valve Face-to-face dimensions comply with PI 609 & MSS-SP-68 esigned to be installed between SME/NSI 16.5 Flanges ompletely assembled and tested, ready for installation pplication These valves are designed to meet the needs of HV and ommercial applications requiring positive shut-off for liquids at higher pressures and temperatures. Typical applications include chiller isolation, cooling tower isolation, change-over systems, large air handler coil control, bypass and process control applications. The large v values provide for an economical control valve solution for larger flow applications. Technical ata Service chilled, hot water, 60% glycol, steam to 50 psi Flow characteristic modifi ed equal percentage, unidirectional ontrollable fl ow range 82 Sizes 2" to 24" Type of end fi tting NSI 300 fl anges Materials ody carbon steel full lug isc 316 stainless steel Seat RPTFE Shaft 17-4 PH stainless Gland seal PTFE ushings glass backed PTFE Media temperature range -20 F to 400 F [-30 to 204 ] ody pressure rating NSI lass 300 lose-off pressure 740 psi Rangeability 100:1 (for 30 deg to 70 deg range) Maximum velocity 32 FPS Leakage bubble tight Valve Nominal Size Type Suitable ctuators v v Electronic IN NSI way Spring Non-Spring Fail-Safe F SHP ½ F SHP F SHP F SHP F SHP F SHP F SHP F SHP F SHP F SHP F SHP F SHP F SHP F SHP MO ON/OFF Valve Size v F SHP F SHP 2½ F SHP F SHP F SHP F SHP F SHP F SHP F SHP F SHP F SHP F SHP F SHP F SHP F Series GM Series SY Series GK Series 30

31 F6 Series 2-Way, NSI lass 300 utterfly Valve Reinforced Teflon Seat, 316 Stainless isc Maximum imensions (Inches) Valve Size v 90 (Max) H No. of Holes Lug olt ctuator lose-off (PSI) F SHP /8-11 UN 150 F SHP 2½ /4-10 UN 150 2*F F SHP /4-10 UN 150 F SHP /4-10 UN 150 F SHP /8-11 UN 150 F SHP 2½ /4-10 UN 150 GK F SHP /4-10 UN 150 F SHP /4-10 UN 150 F SHP /8-11 UN 400 F SHP 2½ /4-10 UN 2*GK 400 F SHP /4-10 UN 400 F SHP /8-11 UN 285 F SHP 2½ /4-10 UN 285 GM F SHP /4-10 UN 285 F SHP /4-10 UN 150 F SHP /8-11 UN 600 F SHP 2½ /4-10 UN 600 SY2 F SHP /4-10 UN 600 F SHP /4-10 UN 600 F SHP /4-10 UN SY SY3 600 F SHP /4-10 UN SY2 285 SY3 600 SY3 150 F SHP /8-9 UN 600 SY4 285 SY5 400 F SHP UN SY7 600 SY4 150 SY5 285 F SHP /8-8 UN SY7 600 SY5 150 SY7 400 F SHP /8-8 UN SY8 600 SY7 150 SY8 285 F SHP /4-8 UN SY9 400 SY SY7 150 SY8 285 F SHP /4-8 UN SY9 400 SY SY8 150 F SHP /4-8 UN SY SY F SHP /2-8 UN SY imension does not include fl ange gaskets. (2 required per valve) pplication Notes imensions 1. Valves are rated at 725 psi differential pressure in the closed 100 F media temperature. 2. Valves are furnished with lugs tapped for use between NSI lass 250/300 fl anges conforming to NSI 16.5 Standards way assemblies are furnished assembled, calibrated and tested, ready for installation. 4. imension allows for actuator(s) removal without the need to remove the valve from the pipe. 5. Weather shields are available, dimensional data furnished upon request. 6. ual actuated valves have actuators mounted on a single common shaft. 7. Flange gaskets (2 required, not provided with valve) MUST be used between valve and NSI fl ange. H 8. Flange bolts are not included with the valve. These are furnished by others. Spring Return Electronic Fail-Safe Non-Spring Return

32 F7 Series 3-Way, NSI lass 300 utterfly Valve Reinforced Teflon Seat, 316 Stainless isc ubble tight shut-off to NSI lass 300 Standards Long stem design allows for 2 insulation minimum Valve Face-to-face dimensions comply with PI 609 & MSS-SP-68 esigned to be installed between SME/NSI 16.5 Flanges ompletely assembled and tested, ready for installation Tees comply with SME/NSI 16.5 lass 250/300 Flanges pplication These valves are designed to meet the needs of HV and ommercial applications requiring positive shut-off for liquids at higher pressures and temperatures. Typical applications include chiller isolation, cooling tower isolation, change-over systems, large air handler coil control, bypass and process control applications. The large v values provide for an economical control valve solution for larger flow applications. Technical ata Service chilled, hot water, 60% glycol, steam to 50 psi Flow characteristic modifi ed equal percentage, unidirectional ontrollable fl ow range 82 Sizes 2" to 24" Type of end fi tting NSI 300 fl anges Materials ody carbon steel full lug isc 316 stainless steel Seat RPTFE Shaft 17-4 PH stainless Gland seal PTFE ushings glass backed PTFE Media temperature range -20 F to 400 F [-30 to 204 ] ody pressure rating NSI lass 300 lose-off pressure 740 psi Rangeability 100:1 (for 30 deg to 70 deg range) Maximum velocity 32 FPS Leakage bubble tight v 60 Valve Nominal Size Type Suitable ctuators IN NSI way Spring Non-Spring Electronic Fail-Safe v F SHP ½ F SHP F SHP F SHP F SHP F SHP F SHP F SHP F SHP F SHP F SHP F SHP F SHP F SHP MO ON/OFF Valve Size v F SHP F SHP 2½ F SHP F SHP F SHP F SHP F SHP F SHP F SHP F SHP F SHP F SHP F SHP F SHP F Series GM Series SY Series GK Series 32

33 0 F7 Series 3-Way, NSI lass 300 utterfly Valve Reinforced Teflon Seat, 316 Stainless isc Maximum imensions (Inches) Valve Size v 90 (Max) H No. of Holes Lug olt ctuator lose-off (PSI) F SHP /8-11 UN 285 F SHP 2½ /4-10 UN 285 2*GK F SHP /4-10 UN 285 F SHP /4-10 UN 150 F SHP /8-11 UN 285 F SHP 2½ /4-10 UN 285 2*GM F SHP /4-10 UN 285 F SHP /4-10 UN 150 F SHP /8-11 UN SY2 400 SY3 600 F SHP 2½ /4-10 UN SY2 400 SY3 600 F SHP /4-10 UN SY2 400 SY3 600 F SHP /4-10 UN SY2 285 SY3 600 F SHP /4-10 UN SY3 285 SY4 600 F SHP /4-10 UN SY3 285 SY4 600 SY4 400 F SHP /8-9 UN SY5 600 SY4 150 SY5 285 F SHP UN SY7 600 SY5 150 SY7 400 F SHP /8-8 UN SY8 600 SY7 150 SY8 400 F SHP /8-8 UN SY SY7 150 SY9 285 F SHP /4-8 UN SY SY SY8 150 F SHP /4-8 UN SY SY F SHP /4-8 UN SY9 150 SY F SHP /2-8 UN SY imensions, and do not include fl ange gaskets. (3 required per valve) pplication Notes 1. Valves are rated at 725 psi differential pressure in the closed 100 F media temperature. 2. Valves are furnished with lugs tapped for use between NSI lass 250/300 fl anges conforming to NSI 16.5 Standards way assemblies are furnished assembled with Tee, calibrated and tested, ready for installation. ll 3 way assemblies require the customer to specify the 3-way confi guration code prior to order entry to guarantee correct placement of valves and actuator(s) on the assembly. 4. imension allows for actuator(s) removal without the need to remove the valve from the pipe. 5. Weather shields are available, dimensional data furnished upon request. 6. ual actuated valves have single actuators mounted on each valve shaft. 7. Flange gaskets (3 required, not provided with valve) MUST be used between valve and NSI fl ange. 8. Flange bolts are not included with the valve. These are furnished by others. imensions S Electronic Fail-Safe Non-Spring Return 104 Note: For tee confi guration, please refer to page 5. 33

34 F6 Series 2-Way, H utterfly Valve Resilient Seat, 304 Stainless isc with Manual Handle or Gear Wheel Operator 200 psi (2 to 12 ) and 150 psi (14-30 ) bubble tight shut-off Long stem design allows for 2 insulation Valve face-to-face dimensions comply with PI 609 & MSS-SP-67 ompletely assembled and tested, ready for installation pplication These valves are designed to meet the needs of HV and commercial applications requiring bubble tight shut-off for liquids. Typical applications include chiller isolation, cooling tower isolation, change-over systems, large air handler coil control, bypass and process control applications. esigned for use in Victaulic piping systems when mated to Victaulic 41 series fl ange nipples. Jobsite Note Valves should be stored in a weather protected area prior to construction. omplete installation recommendations can be found in elimo s Installation and Maintenance Instructions for F6 H utterfl y Valves. Technical ata Service chilled, hot water, 60% glycol Flow characteristic modifi ed equal percentage ontrollable fl ow range 82 Sizes 2 to 30 Type of end fi tting for use with NSI 125/150 fl anges Materials ody ductile iron STM 536 ody fi nish epoxy powder coated isc 304 stainless steel Seat EPM standard Shaft 416 stainless steel O-ring EPM ushings RPTFE Media temperature range -22 F to 250 F [-30 to 120 ] ody pressure rating SME/NSI lass 125/150 lose-off pressure 200 psi (2-12 ), 150 psi (14-30 ) Rangeability 10:1 (for 30 to 70 range) Maximum velocity 12 FPS Leakage bubble tight Valve Nominal Size Type Manual Operators v v N IN [mm] 2-way F650H ½ 65 F665H F680H F6100H F6125H F6150H F6200H F6250H F6300H F6350H F6400H F6450H F6500H F6600H F6750H Valve Size v F650H F665H 2½ F680H F6100H F6125H F6150H F6200H F6250H F6300H F6350H F6400H F6450H F6500H F6600H F6750H Handle Gear Wheel OP 34

35 F6 Series 2-Way, H utterfly Valve Resilient Seat, 304 Stainless isc with Manual Handle or Gear Wheel Operator Maximum imensions (Inches) Valve Size v 90 v 60 E H No. of Holes Lug olt Operator lose-off (PSI) Weight (lbs [kg]) n/a n/a /8-11 UN [5.1] F665H 2½ n/a n/a /8-11 UN HN [6.0] F680H n/a n/a /8-11 UN [6.1] F6100H n/a n/a /8-11 UN [8.7] F6125H n/a n/a /4-10 UN HN [11.0] F6150H n/a n/a /4-10 UN [13.2] F6200H n/a n/a /4-10 UN HN [19.7] Valve Size v 90 v 60 E H No. of Holes Lug olt Operator lose-off (PSI) Weight (lbs [kg]) /8-11 UN [8.6] F665H 2½ /8-11 UN GW [9.5] F680H /8-11 UN [9.5] F6100H /8-11 UN [12.2] F6125H /4-10 UN GW [14.5] F6150H /4-10 UN [16.7] F6200H /4-10 UN [26.3] GW03 F6250H /8-9 UN [37.6] F6300H /8-9 UN [59.0] GW04 F6350H UN [81.4] F6400H UN GW [122.4] F6450H /8-7 UN GW [142.4] F6500H /8-7 UN GW [216.5] F6600H /4-7 UN GW [329.0] F6750H /4-7 UN GW [568.1] imensions Manual Handle imensions Gear Wheel.H. imension is compressed, add for relaxed state. elimovalve_handle_assymodel E.H. elimovalve_handle_assymodel pplication Notes 1. Valves are rated at 200 psi differential pressure in the closed position (SY psi 14 +). 2. Valves are furnished with lugs tapped for use with NSI lass 125/150 fl anges. Installation fl anges and hardware are not included way assemblies are furnished assembled and tested, ready for installation. 35

36 F6 Series 2-Way, NSI lass 150 utterfly Valve Reinforced PTFE Seat, 316 Stainless isc with Manual Handle or Gear Wheel Operator ubble tight shut-off to NSI lass 150 Standards Long stem design allows for 2 insulation minimum Valve face-to-face dimensions comply with PI 609 & MSS-SP-68 esigned to be installed between SME/NSI 16.5 Flanges ompletely assembled and tested, ready for installation pplication These valves are designed to meet the needs of HV and ommercial applications requiring positive shut-off for liquids at higher pressures and temperatures. Typical applications include chiller isolation, cooling tower isolation, change-over systems, large air handler coil control, bypass and process control applications. Jobsite Note Valves should be stored in a weather protected area prior to construction. omplete installation recommendations can be found in elimo s Installation and Maintenance Instructions for F6...SHP-150 utterfl y Valves. Technical ata Service chilled, hot water, 60% glycol, steam to 50 psi Flow characteristic modifi ed equal percentage, unidirectional ontrollable fl ow range 82 Sizes 2" to 24" Type of end fi tting for use with SME/class 125/150 fl ange Materials ody carbon steel full lug isc 316 stainless steel Seat RPTFE Shaft 17-4 PH stainless Gland seal PTFE ushings glass backed PTFE Media temperature range -20 F to 400 F [-30 to 204 ] ody pressure rating NSI lass 150 lose-off pressure 285 psi Rangeability 100:1 (for 30 deg to 70 deg range) Maximum velocity 32 FPS Leakage bubble tight Valve Nominal Size Type v v IN N [mm] NSI way F SHP ½ 65 F SHP F SHP F SHP F SHP F SHP F SHP F SHP F SHP F SHP F SHP F SHP F SHP F SHP F SHP Manual Operators Valve Size v F SHP F SHP 2½ F SHP F SHP F SHP F SHP F SHP F SHP F SHP F SHP F SHP F SHP F SHP F SHP F SHP Handle Gear Wheel OP 36

37 F6 Series 2-Way, NSI lass 150 utterfly Valve Reinforced PTFE Seat, 316 Stainless isc with Manual Handle or Gear Wheel Operator Maximum imensions (Inches) Valve Size v 90 E H No. of Holes Lug olt Operator Weight (lbs [kg]) F SHP n/a n/a /8-11 UN 18 [8.2] HN05 F SHP 2½ n/a n/a /8-11 UN 18 [8.2] F SHP n/a n/a /8-11 UN 20 [9.1] HN06 F SHP n/a n/a /8-11 UN 32 [14.5] F SHP n/a n/a /4-10 UN 38 [17.2] HN07 F SHP n/a n/a /4-10 UN 46 [20.9] F SHP n/a n/a /4-10 UN HN08 59 [26.8] Valve Size v 90 E H No. of Holes Lug olt Operator Weight (lbs [kg]) F SHP /8-11 UN 25 [11.3] GW10 F SHP 2½ /8-11 UN 25 [11.3] F SHP /8-11 UN 28 [12.7] GW11 F SHP /8-11 UN 38 [17.2] F SHP /4-10 UN 48 [21.8] GW12 F SHP /4-10 UN 49 [22.2] F SHP /4-10 UN GW13 58 [26.3] F SHP /8-9 UN GW [50.8] F SHP /8-9 UN GW [73.9] F SHP UN GW [97.5] F SHP UN GW [129.3] F SHP /8-8 UN GW [161.0] F SHP /8-8 UN GW [226.8] F SHP /4-8 UN GW [371.9] F SHP /4-8 UN GW [612.3] lose-off (PSI) NSI lass 150 Limitations lose-off (PSI) NSI lass 150 Limitations imensions Manual Handle imensions Gear Wheel.H. imension does not include flange gaskets. (2 required per valve) pplication Notes 1. Valves are rated at 285 psi differential pressure in the closed position. 2. Valves are furnished with lugs tapped for use between NSI lass 125/150 fl anges conforming to NSI 16.5 Standards way assemblies are furnished assembled and ready for installation. 4. Flange gaskets (2 required, not provided with valve) MUST be used between valve and NSI fl ange. 5. Flange bolts are not included with the valve. These are furnished by others. elimouto_handle SHP series valves have a preferred flow direction. E.H. elimo uto_gear PreferredFlowrate 37

38 F6 Series 2-Way, NSI lass 300 utterfly Valve Reinforced PTFE Seat, 316 Stainless isc with Manual Handle or Gear Wheel Operator ubble tight shut-off to NSI lass 300 Standards Long stem design allows for 2 insulation minimum Valve face-to-face dimensions comply with PI 609 & MSS-SP-68 esigned to be installed between SME/NSI 16.5 Flanges ompletely assembled and tested, ready for installation pplication These valves are designed to meet the needs of HV and ommercial applications requiring positive shut-off for liquids at higher pressures and temperatures. Typical applications include chiller isolation, cooling tower isolation, change-over systems, large air handler coil control, bypass and process control applications. Jobsite Note Valves should be stored in a weather protected area prior to construction. omplete installation recommendations can be found in elimo s Installation and Maintenance Instructions for F6...SHP-300 utterfl y Valves. Technical ata Service chilled, hot water, 60% glycol, steam to 50 psi Flow characteristic modifi ed equal percentage, unidirectional ontrollable fl ow range 82 Sizes 2" to 24" Type of end fi tting NSI 300 fl anges Materials ody carbon steel full lug isc 316 stainless steel Seat RPTFE Shaft 17-4 PH stainless Gland seal PTFE ushings glass backed PTFE Media temperature range -20 F to 400 F [-30 to 204 ] ody pressure rating NSI lass 300 lose-off pressure 740 psi Rangeability 100:1 (for 30 deg to 70 deg range) Maximum velocity 32 FPS Leakage bubble tight Valve Nominal Size Type v v IN N [mm] NSI way F SHP ½ 65 F SHP F SHP F SHP F SHP F SHP F SHP F SHP F SHP F SHP F SHP F SHP F SHP F SHP Manual Operators Valve Size v F SHP F SHP 2½ F SHP F SHP F SHP F SHP F SHP F SHP F SHP F SHP F SHP F SHP F SHP F SHP Handle Gear Wheel OP 38

39 F6 Series 2-Way, NSI lass 300 utterfly Valve Reinforced PTFE Seat, 316 Stainless isc with Manual Handle or Gear Wheel Operator Maximum imensions (Inches) Valve Size v 90 E H No. of Holes Lug olt Operator Weight (lbs [kg]) F SHP n/a n/a /8-11 UN 15 [6.8] HN05 F SHP 2½ n/a n/a /4-10 UN 15 [6.8] F SHP n/a n/a /4-10 UN 21 [9.5] HN06 F SHP n/a n/a /4-10 UN 29 [13.2] F SHP n/a n/a /4-10 UN 38 [17.2] HN07 F SHP n/a n/a /4-10 UN 62 [28.1] Valve Size v 90 E H No. of Holes Lug olt Operator Weight (lbs [kg]) F SHP /8-11 UN 23 [10.4] GW10 F SHP 2½ /4-10 UN 23 [10.4] F SHP /4-10 UN 29 [13.2] GW11 F SHP /4-10 UN 35 [15.9] F SHP /4-10 UN GW12 41 [18.6] F SHP /4-10 UN GW13 63 [28.6] F SHP /8-9 UN GW14 93 [42.2] F SHP UN GW [68.0] F SHP /8-8 UN GW [104.3] F SHP /8-8 UN GW [163.3] F SHP /4-8 UN GW [197.3] F SHP /4-8 UN GW [276.7] F SHP /4-8 UN GW [415.0] F SHP /2-8 UN GW [544.3] lose-off (PSI) NSI lass 300 Limitations lose-off (PSI) NSI lass 300 Limitations imensions Manual Handle imensions Gear Wheel.H. imension does not include fl ange gaskets. (2 required per valve) pplication Notes 1. Valves are rated at 600 psi differential pressure in the closed position. 2. Valves are furnished with lugs tapped for use between NSI lass 250/300 fl anges conforming to NSI 16.5 Standards way assemblies are furnished assembled and ready for installation. 4. Flange gaskets (2 required, not provided with valve) MUST be used between valve and NSI fl ange. 5. Flange bolts are not included with the valve. These are furnished by others. elimouto_handle E SHP series valves have a preferred flow direction..h. elimo uto-gear PreferredFlowrate 39

40 Maintenance Instructions SHP Series High Performance utterfly Valves Safety Precautions efore removing the valve from the line or loosening any bolts, it is important to verify the following conditions: 1. e sure the line is depressurized and drained. 2. e sure of the pipeline media. Proper care should be taken for protection against toxic and/or fl ammable fl uids. 3. Never install the valve without an Operator (Manual or utomatic) already attached to the valve shaft. 4. Never remove the Operator from the valve while the valve is in the pipeline under pressure. elimo s valve design may allow line pressure to open the valve if the handle/actuator is not in place while the valve is under pressure. 5. lways be sure that the disc is in the full-closed position before removing or installing the valve. 6. Take care in handling the valve. Personal injury or property damage may result if the valve is damaged or mishandled during maintenance operations. General Maintenance Normal maintenance for a elimo SHP valve is limited to adjustment of the shaft packing by tightening down evenly on the gland fl ange using the gland fl ange studs and nuts. Overtightening of the gland should be avoided since this will shorten the life of the packing. uring commissioning, it is common for dirt and foreign objects to be left in the pipeline during construction. This debris can damage the FV seat or disc edge which will prevent the valve from providing tight shutoff. In such cases seat replacement may be necessary. Packing Replacement 1. Remove the handle or actuator and the mounting hardware from the valve. 2. Remove the gland fl ange nuts and lock washers. 3. Remove the gland fl ange and gland. 4. Replace the old packing with new packing. orrect packing selection is important. On larger valves it may be necessary to compress each stem seal into the stuffi ng box before adding the next one. 5. Reinstall gland, gland fl ange, lock washers and nuts. 6. Tighten the gland fl ange nuts evenly to torque specifi ed in Table Operate the disc several times. 8. Reinstall the handle or actuator and mounting hardware. 9. Set the actuator stops. End ap Seal Replacement (where applicable) 1. Remove the end cap bolts and lock washers. 2. Rotate the end cap to break the seal, then pull the cap out. 3. Remove the old seal. 4. lean the body and end cap prior to installing the new seal. 5. Slide the new seal into place, then guide the end cap into the body. 6. lign the bolt holes and reinstall the lock washers and bolts. 7. Tighten the bolts evenly to the torque specifi ed in Table 2. Table 2 Valve Size (in.) Torque (in-lb) 2 to to to Standard Soft Seat Replacement 1. Place the valve on a bench with the seat retainer facing up. Use blocks to elevate the valve above the work surface to provide enough clearance to prevent the disc from being damaged when the valve is opened. 2. (a) ap Screw Retainer: Remove the cap screws and lift the seat retainer out of the valve. (b) Wedge Ring Retainer: Unlock the retainer by removing the set screws. If diffi culty is experienced in removing the retainer, open the disc approximately 20 degrees and then tap the retainer with a non-metallic hammer. Lift the retainer from the body. 3. Remove the old seat from the seat retainer and discard. 4. Thoroughly clean the seat cavity in the body and the seat retainer prior to installing a new seat. Table 1 Valve Size (in.) Torque (in-lb) 2 to to to to to

41 Maintenance Instructions SHP Series High Performance utterfly Valves elimo uses a wedge pin method of disc/shaft pinning. This method permits the replacement of either a disc or a shaft since they are not required to be matched sets. 1. Remove any actuator and mounting bracket from top of valve. 2. Remove all top and bottom packing and/or end seals as required. 3. To prepare for removal of existing wedge pins, grind away any disc material that has been peened over pin heads. 4. (a) For Through Shaft esign: Using a punch approximately the same size as the wedge pins, drive each pin out of the disc hub from the non-peened side of the disc to the peened side of the disc. (b) For Split Shaft esign: Pull the wedge pins out of the disc hub using the threaded holes on top of each pin and a jack screw. 5. Support the valve body and disc on a fl at surface in the horizontal position. Slowly remove shaft(s). 6. Remove the disc from the body. 7. To remove bearings, cut or grind a slot lengthwise in each bearing in order to be able to collapse bearing prior to removal. e careful not to damage bearing seating bore within the body. 8. lean all components thoroughly. 9. Inspect all parts for damage prior to reassembly. amaged parts should be repaired or replaced with new parts. 10. arefully clean and polish the disc sealing surface with a soft cloth. The disc sealing surface should be free of all grooves and scratches. 11. Install the new bearings by gently tapping them into the body with a soft rod and hammer. The bearings should be installed into the shaft bore firmly against the counterbore or bottom of shaft hole. 12. (a) () Valves 2 through 12 : With the valve body on the edge of the bench, shaft horizontal, and the body overtravel stop nearest to the bench, position the disc in the open position with the fl at face upward. Present the disc to the valve body from the side opposite the seat retainer cavity. (b) () Valves 14 and larger: Support the disc on a bench, fl at side down and elevated above the bench top to a height of approximately 4 inches. Lower the valve body over the disc, seat retainer side facing upward, until the bearing bore and disc hole are aligned. Install the shaft into the body and disc. 13. The shaft keyway when viewed from the top of the valve should be to the right, which is also the direction from which the pins are installed. 14. Line up the shaft fl at to permit the insertion of the wedge pins. Install the fi rst wedge pin in the disc hole closest to the top of the valve. Finger tight installation is appropriate. 15. Move the shaft fully into the valve and against this fi rst installed pin. Insert the second pin. Tap both wedge pins in equal amounts until all play between shaft and disc is removed. are should be taken to not over seat the wedge pins. If the pin is fl ush or protruding after tapping in, tack weld on the opposite side for security. Otherwise, peening of the installing side is recommended. 16. Install a new end seal if applicable with the end cap as described in Steps 4 through 7 of the End ap Seal Replacement procedure. 17. Install new packing box components as described in Steps 4 through 10 of the Packing Replacement procedure. 18. Install new seat as described in the Seat Replacement procedure. 19. ycle the valve several times to ensure the disc is pinned tightly to the shaft and there is no shaft binding or seat damage before reinstalling the valve in the pipeline. 20. Reinstall the actuator mounting hardware and actuator. Remote ctuator (Male rive) djust the stops in the actuator to position the face of the disc parallel with the face of the valve body in the closed position and perpendicular to the face of the valve body in the open position. aution: The overtravel stop in the valve body is not to be used as an actuator stop. isc, Shaft and earing Replacement Parts List Through Shaft esign Item escription Number 1 ody 2 Seat Retainer 3 isc 4 Shaft 5 Seat 6 Seat O-Ring 7 earing 8 Packing 9 Gland 10 Gland Follower 11 isc Thrust Spacer (2 to 5 ) 12 Set Screws 13 Wedge Pins 14 Gland Flange Stud 15 Gland Flange Nut 16 Lock Washer 17 Wedge Ring 41

42 Features / enefits utterfly Valves SY Series ctuators elimo s SY series electric actuators have been designed to mate with our H(U), Grooved and SHP series butterfly valves and other quarter turn valve applications. The patented gear drive mechanism provides for efficient, smooth operation while allowing easy manual override at any time. rawing upon years of experience in the actuation industry, we have incorporated the most desirable features into the SY product range. ll units have NEM 4X ratings, easily visible position indicators, international standard ISO5211 mounting systems, internal thermal motor overload protection, heater, dual auxiliary Form switches, and easily accessible wiring termination points. Wiring diagrams, included in all printed documentation, are also affixed to the outside of the housing on the permanently attached product label. The units are easily visible in mechanical rooms with their characteristic elimo Orange color. Torque ranges are available from 310 to 31,150 in lbs. omed Position Indicator ast luminum over Powder oated NEM 4X Rated Housing Four over Screws for Easy ccess Easily ccessible Field Wiring Terminal Positive Locking Switch ams ISO 5211Mounting System Thermally Protected rive Motor Simple, Single Handed Override Wheel (SY2~12) earing Seals Hardened Steel Gear Sets 42

43 SY...24V Series Non-Spring Return ctuator Tecnhincal ata - 24 V pplication: The SY actuators are NEM 4X rated and designed to meet the needs of HV and ommercial applications. Offered on elimo standard and high performance valve series, these actuators are available for on/off and modulating applications. epending on the application, they are available in 24 V/ V, 120 V and 230 V. Technical ata Electrical connection Motor protection Gear train Operating range Sensitivity ½ conduit connector, screw terminals H lass insulation (SY-1), F lass (SY-2 5) high alloy steel gear sets, self locking (SY -24) on/off, floating point (SY...24MFT) 2-10 V, 4-20m, 0-10 V (SY 24MFT) 0.4m/200mV Reversal hysteresis (SY 24MFT)1.0m/500mV Feedback (SY 24MFT) 2-10 V ngle of rotation 90 irection of rotation reversible Position indication top mounted domed indicator Internal humidity control resistive heating element uxiliary switches (2) SPT, V factory set for 5 and 85 change of state mbient temperature -22 F to +150 F [-30 to +65 ] Humidity range up to 95% Housing type IP67, NEM 4X Housing material die cast aluminum alloy gency listings ISO, E, csus Power Supply Model Torque Speed 24 V/V 50/60Hz, single phase Power onsumption uty ycle Override SY1-24(P) 35Nm/310 in-lbs 15s % 75% 8mm Wrench 2.0kg/4.9 lb. SY2-24(MFT) 90Nm/801 in-lbs 15s % 75% Hand Wheel 11kg/24.5 lb. SY3-24(MFT) 150Nm/1335 in-lbs 22s % 75% Hand Wheel 11kg/24.5 lb. SY4-24(MFT) 400Nm/3560 in-lbs 16s % 75% Hand Wheel 22kg/48.5 lb. SY5-24(MFT) 500Nm/4450 in-lbs 22s % 75% Hand Wheel 22kg/48.5 lb. On/Off MFT Weight 43

44 SY...120V Series Non-Spring Return ctuator Tecnhincal ata V pplication: The SY actuators are NEM 4X rated and designed to meet the needs of HV and ommercial applications. Offered on elimo standard and high performance valve series, these actuators are available for on/off and modulating applications. epending on the application, they are available in 24 V/ V, 120 V and 230 V. Technical ata Electrical connection Motor protection Gear train Operating range Sensitivity ½ conduit connector, screw terminals H lass insulation (SY-1), F lass (SY-2 12) high alloy steel gear sets, self locking (SY -110) on/off, floating point (SY...120MFT) 2-10 V, 4-20m, 0-10 V (SY 120MFT) 0.4m/200mV Reversal hysteresis (SY 120MFT) 1.0m/500mV Feedback (SY 120MFT) 2-10 V ngle of rotation 90 irection of rotation reversible Position indication top mounted domed indicator Internal humidity control resistive heating element uxiliary switches (2) SPT, V factory set for 5 and 85 change of state mbient temperature -22 F to +150 F [-30 to +65 ] Humidity range up to 95% Housing type IP67, NEM 4X Housing material die cast aluminum alloy gency listings ISO, E, csus Note: Leakage current is possible (<3.5 m). onnect ground before applying voltage. Power Supply 120 V 50/60Hz, single phase Speed Speed Power uty ycle Model Torque 60Hz 50Hz onsumption On/Off Proportional Override Weight SY1-110(P) 35Nm/310 in-lbs 12s 13s % 75% 8mm Wrench 2.0kg/4.9 lb. SY2-110(MFT) 90Nm/801 in-lbs 15s 17s % 75% Hand Wheel 11kg/24.5 lb. SY3-110(MFT) 150Nm/1335 in-lbs 22s 26s % 75% Hand Wheel 11kg/24.5 lb. SY4-110(MFT) 400Nm/3560 in-lbs 16s 18s % 75% Hand Wheel 22kg/48.5 lb. SY5-110(MFT) 500Nm/4450 in-lbs 22s 25s % 75% Hand Wheel 22kg/48.5 lb. SY6-110(MFT) 650Nm/5785 in-lbs 28s 31s % 75% Hand Wheel 22kg/48.5 lb. SY7-110(MFT) 1000Nm/8900 in-lbs 46s 55s % 75% Hand Wheel 36kg/79.5 lb. SY8-110(MFT) 1500Nm/13350 in-lbs 46s 55s % 75% Hand Wheel 36kg/79.5 lb. SY9-110(MFT) 2000Nm/17800 in-lbs 58s 70s % 50% Hand Wheel 56kg/123.5 lb. SY10-110(MFT) 2500Nm/22250 in-lbs 58s 70s % 50% Hand Wheel 56kg/123.5 lb. SY11-110(MFT) 3000Nm/26700 in-lbs 58s 70s % 50% Hand Wheel 56kg/123.5 lb. SY12-110(MFT) 3500Nm/31150 in-lbs 58s 70s % 50% Hand Wheel 56kg/123.5 lb. 44

45 SY...230V Series Non-Spring Return ctuator Tecnhincal ata - 23 V pplication: The SY actuators are NEM 4X rated and designed to meet the needs of HV and ommercial applications. Offered on elimo standard and high performance valve series, these actuators are available for on/off and modulating applications. epending on the application, they are available in 24 V/ V, 120 V and 230 V. Technical ata Electrical connection Overload protection Motor protection Gear train Operating range Power Supply Model ½ conduit connector, screw terminals thermally protected 135 cut-out H lass insulation (SY-1), F lass (SY-2 12) high alloy steel gear sets, self locking (SY -220) on/off, floating point (SY...230MFT) 2-10 V, 4-20m, 0-10 V Sensitivity (SY 230MFT) 0.4m/200mV Reversal hysteresis (SY 230MFT) 1.0m/500mV Feedback (SY 230MFT) 2-10 V ngle of rotation 90 irection of rotation reversible Position indication top mounted domed indicator Internal humidity control resistive heating element uxiliary switches (2) SPT, V factory set for 5 and 85 change of state mbient temperature -22 F to +150 F [-30 to +65 ] Humidity range up to 95% Housing type IP67, NEM 4X Housing material die cast aluminum a lloy gency listings ISO, E, csus Torque Speed 60Hz 230 V 50/60Hz, single phase Speed 50Hz Power onsumption uty ycle On/Off MFT Override SY1-220(P) 35Nm/310 in-lbs 12s 13s % 75% 8mm Wrench 2.0kg/4.9 lb. SY2-220(MFT) 90Nm/801 in-lbs 15s 17s % 75% Hand Wheel 11kg/24.5 lb. SY3-220(MFT) 150Nm/1335 in-lbs 22s 26s % 75% Hand Wheel 11kg/24.5 lb. SY4-220(MFT) 400Nm/3560 in-lbs 16s 18s % 75% Hand Wheel 22kg/48.5 lb. SY5-220(MFT) 500Nm/4450 in-lbs 22s 25s % 75% Hand Wheel 22kg/48.5 lb. SY6-220(MFT) 650Nm/5785 in-lbs 28s 31s % 75% Hand Wheel 22kg/48.5 lb. SY7-220(MFT) 1000Nm/8900 in-lbs 46s 55s % 75% Hand Wheel 36kg/79.5 lb. SY8-220(MFT) 1500Nm/13350 in-lbs 46s 55s % 75% Hand Wheel 36kg/79.5 lb. SY9-220(MFT) 2000Nm/17800 in-lbs 58s 70s % 50% Hand Wheel 56kg/123.5 lb. SY10-220(MFT) 2500Nm/22250 in-lbs 58s 70s % 50% Hand Wheel 56kg/123.5 lb. SY11-220(MFT) 3000Nm/26700 in-lbs 58s 70s % 50% Hand Wheel 56kg/123.5 lb. SY12-220(MFT) 3500Nm/31150 in-lbs 58s 70s % 50% Hand Wheel 56kg/123.5 lb. Weight 45

46 SY... Series Non-Spring Return ctuator imensions SY-2~6... SY-1... SY-9~12... SY-7~8... MOEL IM (MX) dd to im for cover removal IM IM (MX) IM Inches [mm] Inches [mm] Inches [mm] Inches [mm] Inches [mm] SY [155] 3.94 [100] 4.25 [108] 8mm - SY2~ [255] 7.48 [190] 7.87 [200] [330] 7.87 [200] SY4~ [315] 8.86 [225] 9.21 [234] [380] [300] SY7~ [420] 8.86 [225] 9.21 [234] [450] [340] SY9~ [590] 8.86 [225] [260] [470] [350] Note: ~ indicates range of actuator i.e., SY2~3 = SY-2 and SY-3 46

47 Wire Size vs. Length of Run for SY Series ctuators SY1 SY2 SY3 SY4 SY5 mps mps mps mps mps wire gauge MX istance between ctuator and Supply (feet) V SY1 SY2 SY3 SY4 SY5 SY6 SY7 SY8 SY9 SY10 SY11 SY12 mps mps mps mps mps mps mps mps mps mps mps mps wire gauge MX istance between ctuator and Supply (feet) V SY1 SY2 SY3 SY4 SY5 SY6 SY7 SY8 SY9 SY10 SY11 SY12 mps mps mps mps mps mps mps mps mps mps mps mps wire gauge MX istance between ctuator and Supply (feet) V The NE mandates that 24 V over 100 V power requires LSS 1 wiring conduit. Local codes may vary. o NOT mix LSS 1 & LSS 2 circuits in the same conduit. Generally, 24 V actuators over 100 V should be changed to 120 V models. 47

48 SY... Series Non-Spring Return ctuator urrent raws 24V / Model Torque Speed (90 ) Motor Power Run Start Lock SY s 10W SY s 70W SY s 70W SY s 180W SY s 180W V Model Torque Speed (90 ) Motor Power Run Start Lock SY s 10W SY s 70W SY s 70W SY s 180W SY s 180W SY s 120W SY s 120W SY s 120W SY s 180W SY s 220W SY s 250W SY s 300W V Model Torque Speed (90 ) Motor Power Run Start Lock SY s 10W SY s 70W SY s 70W SY s 180W SY s 180W SY s 120W SY s 120W SY s 120W SY s 180W SY s 220W SY s 250W SY s 300W RUN- normal operation STRT- initial current draw LOK- power to the actuator but the motor is not moving 48

49 Interface Wiring etail SYx-MFT, 24V, 120/230V ctuators: SYx-MFT INSTLLTION NOTES UTION Notes: 1. Motor MS have been factory calibrated and should not be moved. 2. n adaption must be performed if any limit switch is adjusted. This will calibrate the beginning and end stopping points. Press the adaption button for 3 seconds and release. 3. New SY actuators must have an adaption performed before operation. P Tool Service Jack onnection ontrol Signal + ontrol Signal - FK + FK - Power Supply om - Power Supply Hot + daption ontrol Signal + ontrol Signal - FK + FK - irection of Rotation 24V N - Power Supply ommon H - Power Supply Hot P Tool Service Jack daption irection of Rotation 120/230V 49

50 Interface Wiring etail SYx-P LE Open LE lose N Power Supply (3) + Power Supply (4) ontrol Signal (5) ontrol Signal (6) Sensitivity switch se tting is position #3 for factory default. To widen deadband, select a higher number (up to 9). Sensitivity Feedback (11) Feedback (12) VR2 VR1 INSTLLTION NOTES UTION Notes: 1. o not change sensitivity or dip switch settings with power applied! 2. VR1 and VR2 are factory calibrated and should not be moved. 3. Motor MS have been factory calibrated and should not be moved. ip Switch Settings OFF ON INPUT = 2-10 V OFF ON RESPONSE = IRET OFF INPUT = 4-20m OFF RESPONSE = REVERSE ON ON WRNING Potentiometer (Factory Pre-set) OFF ON OFF ON OFF ON INPUT = 1-5 V OUTPUT = 4-20m OUTPUT = 2-10 V For 2-position actuators with 1k feedback option Potentiometer points 1, 2, 3 are wired to terminal blocks 8, 9, 10. When a valve is closed: 8, 9 1k Ω 9, 10 0k Ω When a valve is opened: 8, 9 0k Ω 9, 10 1k Ω OFF ON OFF ON OFF ON LOSS OF SIGNL = LOSE (irect cting) LOSS OF SIGNL = OPEN (Reverse cting) LOSS OF SIGNL = OPEN (irect cting) LOSS OF SIGNL = LOSE (Reverse cting) LOSS OF SIGNL = STOP *On modulating actuators O NOT master/ slave using optional potentiometer. For modulating actuators with 1k feedback option* Potentiometer points 1, 2, 3 are wired to terminal blocks 8, 9, 10. When a valve is closed: 8, 9 1k Ω 9, 10 0k Ω When a valve is opened: 8, 9 0k Ω 9, 10 1k Ω 50

51 SY... Series Non-Spring Return ctuator UTION Electrical Travel djustment (Factory Pre-set) SY-1 Factory pre-set see chart below. Field adjustable if required LS4 uxiliary Switch for losed Indication LS4 LS3 LS2 LS1 LS3 uxiliary Switch for Opened Indication Factory pre-set and calibrated. o not adjust - warranty voided LS2 LOSE lockwise ecrease losed ngle ounter-clockwise Increase losed ngle LS1 OPEN lockwise Increase Opening ngle ounter-clockwise ecrease Opening ngle SY-2-12 UTION Electrical Travel djustment Factory pre-set see chart below. Field adjustable if required LS4 uxiliary Switch for losed Indication LS3 uxiliary Switch for Opened Indication LS4 WRNING F E LS4 LS3 LS3 LS2 LS1 Factory pre-set and calibrated. o not adjust - warranty voided LS2 LOSE LS1 OPEN Switches at left are shown with actuator fully open LS LS4 - F - E lockwise ecrease losed ngle ounter-clockwise Increase losed ngle lockwise Increase Opening ngle ounter-clockwise ecrease Opening ngle INSTLLTION NOTES UTION Notes: 1. n adaption must be performed when the limit switches are adjusted. For the SYx-MFT actuators. This will calibrate the beginning and end stopping points. Press the adaption button for 3 seconds and release. 51

52 W546_12 Wiring for ontrol Valves On/Off, 24V, 120/230V SY ctuator Wiring iagram, SY1 5-24V On/Off SY V or 230V On/Off Hazard Identification Warnings and autions appear at appropriate sections throughout this manual. Read these carefully. UTION Indicates a potentially hazardous situation which, if not avoided, may result in minor or moderate injury. It may also be used to alert against unsafe practices. Indicates an action or condition that may cause irreversible damage to the actuator(s) or associated equipment. Equipment damage! Power consumption and input impedance must be observed. NOTES SY Each actuator should be powered by a single, isolated 33 control transformer. using a common control signal input. INSTLLTION NOTES Observe class 1 and class 2 wiring restrictions. Transformer sizing = SY actuator draw X 1.25 (safety margin) (Ex. SY2-24 requires 3.0 x 1.25 = 3.75, 3.75 X 24 V = 90V Transformer). NOTES SY V or 230V aution: Power Supply Voltage using a common control signal input V / Transformer G G Ground 120V or 230V / G G Ground Line Volts LS3 Open lose LS3 1 ommon 3 Open 4 losed onnect to #1 for fully 5 open indication 6 7 E F LS3 HTR - (Open Indication) LS4 -F (losed Indication) ontact Rating: V Max. SY N L1 H L2 Open lose 1 ommon 3 Open 4 losed onnect to #1 for fully 5 open indication 6 7 HTR E F LS3 - (Open Indication) LS4 -F (losed Indication) ontact Rating: V Max. SY V or 230V E - (Open Indication) ontact Rating: V Max V Max. LS4 E - (Open Indication) ontact Rating: V Max V Max. LS4 F -E (losed Indication) F -E (losed Indication) SY1-24 SY1-110 (220) SY1 ontact rrangements 52

53 W547_11 Wiring for ontrol Valves Proportional, 24V, 120/230V SY ctuator Wiring iagram, SY1-24P and SY1-110P (220P) Hazard Identification this manual. Read these carefully. UTION may result in minor or moderate injury. It may also be used to alert against unsafe practices. Indicates an action or condition that may cause irreversible damage to the actuator(s) or associated equipment. INSTLLTION NOTES PPLITION NOTES Ground shielded wire at control panel chassis. Tape back ground at actuator. Use of feedback is optional. NOTES SY1 24P Each actuator should be powered by a single, isolated 33 control transformer. " " wiring to a common is prohibited. Terminals 4 and 6 need to be wired separately. NOTES SY1 110P (220P) aution: " " wiring to a common is prohibited. Terminals 4 and 6 need to be wired separately V / Transformer G G Ground 120 or 230 V G G Ground Line Voltage 4 Power Supply om 5 Power Supply Hot N L1 H L2 4 Power Supply om 5 Power Supply Hot ontrol signal Feedback ontrol Signal (-) 7 ontrol Signal (+) 8 Internal Use Only 9 Internal Use Only 10 Internal Use Only 11 Feedback (-) 12 Feedback (+) E F LS3 LS4 SY1-24P ontrol signal Feedback ontrol Signal (-) 7 ontrol Signal (+) 8 Internal Use Only 9 Internal Use Only 10 Internal Use Only 11 Feedback (-) 12 Feedback (+) E F LS3 LS4 SY1-110P (220P) 53

54 W547_2_11 Wiring for ontrol Valves Proportional, 24V, 120/230V ctuator: SY2 5-24MFT SY MFT SY MFT Hazard Identification this manual. Read these carefully. UTION Indicates a potentially hazardous situation which, if not avoided, may result in minor or moderate injury. It may also be used to alert against unsafe practices. Indicates an action or condition that may cause irreversible damage to the actuator(s) or associated equipment. INSTLLTION NOTES PPLITION NOTES Ground shielded wire at control panel chassis. Tape back ground at actuator. Use of feedback is optional. NOTES SY MFT Each actuator should be powered by a single, isolated 33 control transformer. " " wiring to a common is prohibited. NOTES SY MFT (230MFT) aution: Internal Use Only Internal Use Only P Tool Service Jack 1 Internal Use Only 2 Internal Use Only 3 Internal Use Only ontrol Signal Feedback ontrol Signal (+) ontrol Signal (-) Feedback Signal (+) Y 1 U5 ddress /- ~/+ Power Supply om Power Supply Hot 24V / Feedback Signal (-) Not Used daption 8 9 Internal Use Only Internal Use Only E ontrol Signal Feedback 36 LS3 LS4 G G 34 Not Used - PE ontrol Signal (+) ontrol Signal (-) Feedback Signal (+) Feedback Signal (-) Not Used - Not Used - PE 2 Y 1 U P Tool Service Jack 10 Internal Use Only Y2 Y1 SYx-24MFT Power Supply om 120v (N) / 230v (L1) Power Supply Hot 120v (H) / 230v (L2) Internal Use Only N L Internal Use Only 1 Internal Use Only 2 Internal Use Only 3 Internal Use Only daption ddress 8 Internal Use Only Y1 9 Internal Use Only Y2 SYx-120MFT 10 Internal Use Only SYx-230MFT F SY MFT SY MFT (230MFT) 54

55 W549_11 Wiring for ontrol Valves On/Off, 24V, 110/120/230V SY ctuator Wiring iagram, SY Multiple Wiring SY (220) Multiple Wiring Hazard Identification Warnings and autions appear at appropriate sections throughout this manual. Read these carefully. UTION Indicates a potentially hazardous situation which, if not avoided, may result in minor or moderate injury. It may also be used to alert against unsafe practices. Indicates an action or condition that may cause irreversible damage to the actuator(s) or associated equipment. Equipment damage! Power consumption and input impedance must be observed. INSTLLTION NOTES Observe class 1 and class 2 wiring restrictions. Transformer sizing = SY actuator draw X 1.25 (safety margin) (Ex. SY2-24 requires 3.0 x 1.25 = 3.75, 3.75 X 24 V = 90V Transformer). NOTES aution: Power Supply Voltage. Isolation relays must be used in parallel connection of multiple actuators using a common control signal input. Should be PT. "H" (L2) cannot be connected to terminal #3 and #4 simultaneously. Required: Terminal #7 needs to be field wired to enable heater circuit. 24V Transformer G G Ground ctuator 120 or 230 V G G Ground ctuator Line Voltage Open lose K1 K1- * 1 ommon 3 Open 4 losed HTR N L1 H L2 Open lose K1 K1-1 ommon 3 Open 4 losed HTR * The isolation relays may not be needed. ependent on signal LS3 LS3 K1- G * LS3 - (Open Indication) LS4 E F -F (losed Indication) ontact Rating: V Max. SY G Ground ctuator 1 ommon 3 Open 4 losed HTR LS3 - (Open Indication) LS4 E -F (losed Indication) F ontact Rating: V Max. K1- G LS3 - (Open Indication) LS4 E -F (losed Indication) F ontact Rating: V Max. SY (220) G Ground ctuator 1 ommon 3 Open 4 losed HTR LS3 - (Open Indication) LS4 E -F (losed Indication) F ontact Rating: V Max. SY SY (220) E - (Open Indication) ontact Rating: V Max V Max. LS4 E - (Open Indication) ontact Rating: V Max V Max. LS4 F -E (losed Indication) F -E (losed Indication) SY1-24 SY1-110 (220) SY1 ontact rrangements 55

56 W550_11 Wiring for ontrol Valves Proportional, 24V SY ctuator Wiring iagram, SY1-24P Multiple Wiring Hazard Identification 33 Warnings and autions appear at appropriate sections throughout this manual. Read these carefully. UTION Indicates a potentially hazardous situation which, if not avoided, may result in minor or moderate injury. It may also be used to alert against unsafe practices. Indicates an action or condition that may cause irreversible damage to the actuator(s) or associated equipment. Equipment damage! Power consumption and input impedance must be observed. INSTLLTION NOTES Observe class 1 and class 2 wiring restrictions. 24V / Transformer Line Voltage G 35 Feedback () 36 G Ground ctuator 4 Power Supply om 5 Power Supply Hot 6 ontrol Signal (-) 7 ontrol Signal (+) 8 Internal Use Only 9 Internal Use Only 10 Internal Use Only 11 Feedback (-) 12 Feedback (+) E F LS3 - (Open Indication) ontact Rating: V Max V Max. LS4 -E (losed Indication) SY1-24P Transformer sizing = SY actuator draw X 1.25 (safety margin) (Ex. SY2-24 requires 3.0 x 1.25 = 3.75, 3.75 X 24 V = 90V Transformer) V / Transformer G G Ground ctuator NOTES SY1-24P Each actuator should be powered by a single, isolated 33 control transformer. SY1-24P notes: Power supply om/neutral and ontrol Signal " " wiring to a common is prohibited. Terminals 4 and 6 need to be wired separately otherwise irreversible damage will occur. power applied PPLITION NOTES Recommended twisted shielded pair for control wiring. Ground shielded wire at control panel chassis. Tape back ground at actuator. Use of feedback is optional. Line Voltage ontrol Signal 35 Feedback () 36 4 Power Supply om 5 Power Supply Hot 6 ontrol Signal (-) 7 ontrol Signal (+) 8 Internal Use Only 9 Internal Use Only 10 Internal Use Only 11 Feedback (-) 12 Feedback (+) E F LS3 - (Open Indication) ontact Rating: V Max V Max. LS4 -E (losed Indication) SY1-24P 56

57 W550_2_11 Wiring for ontrol Valves Proportional, Multiple Wiring, 24V ctuators: SY MFT Hazard Identification Warnings and autions appear at appropriate sections throughout this manual. Read these carefully. UTION Indicates a potentially hazardous situation which, if not avoided, may result in minor or moderate injury. It may also be used to alert against unsafe practices. INSTLLTION NOTES Observe class 1 and class 2 wiring restrictions. Transformer sizing = SY actuator draw X 1.25 (safety margin) (Ex. SY2-24 requires 3.0 x 1.25 = 3.75, 3.75 X 24 V = 90V Transformer). Indicates an action or condition that may cause irreversible damage to the actuator(s) or associated equipment. Equipment damage! Power consumption and input impedance must be observed NOTES SY MFT Each actuator should be powered by a single, isolated control transformer. PPLITION NOTES Recommended twisted shielded pair for control wiring. Ground shielded wire at control panel chassis. Tape back ground at actuator. 36 Use of feedback is optional. ctuator Internal Use Only Internal Use Only P Tool Service Jack 1 Internal Use Only 2 Internal Use Only 3 Internal Use Only ontrol Signal Feedback 36 Feedback 35 G ontrol Signal (+) ontrol Signal (-) Feedback Signal (+) Feedback Signal (-) Not Used - Not Used - PE ontrol Signal (+) ontrol Signal (-) Feedback Signal (+) Y 1 U ctuator Y 1 U5 ddress daption Y1 ddress Y2 P Tool Service Jack SYx-24MFT /- ~/ /- ~/+ Power Supply om Power Supply Hot Internal Use Only Internal Use Only Internal Use Only Internal Use Only Internal Use Only Internal Use Only Internal Use Only Internal Use Only Power Supply om Power Supply Hot 24V / 33 24V / 33 LS3 - (Open Indication) Feedback Signal (-) Not Used - Not Used daption Y1 Y2 SYx-24MFT Internal Use Only Internal Use Only Internal Use Only E F LS4 -F (losed Indication) ontact Rating: V Max. G PE SY2 5-24MFT 57

58 W552_1_11 Proportional, 110/220V, 120/230V ctuators: SY1-110P SY1-220P Hazard Identification 120 or 230 V G G Ground Warnings and autions appear at appropriate N L1 4 Power Supply om sections throughout this manual. Read these carefully. H L2 5 Power Supply Hot UTION 6 ontrol Signal (-) Indicates a potentially hazardous situation which, if 7 ontrol Signal (+) not avoided, may result in minor or moderate injury. It may also be used to alert against unsafe practices Internal Use Only 9 Internal Use Only Indicates an action or condition that may cause irreversible damage to the actuator(s) or associated equipment. Equipment damage! Power consumption and input impedance must be observed. INSTLLTION NOTES Observe class 1 and class 2 wiring restrictions. Feedback () 36 ctuator 10 Internal Use Only 11 Feedback (-) 12 Feedback (+) E F LS3 - (Open Indication) ontact Rating: V Max V Max. LS4 -E (losed Indication) SY1-110P (220P) PPLITION NOTES G G Ground ctuator Recommended twisted shielded pair for control wiring. Ground shielded wire at control panel chassis. Tape back ground at actuator. Use of feedback is optional. NOTES SY1-110P (220P) aution: Power supply voltage. power applied. ontrol Signal 35 Feedback () 36 4 Power Supply om 5 Power Supply Hot 6 ontrol Signal (-) 7 ontrol Signal (+) 8 Internal Use Only 9 Internal Use Only 10 Internal Use Only 11 Feedback (-) 12 Feedback (+) E F LS3 - (Open Indication) ontact Rating: V Max V Max. LS4 -E (losed Indication) SY1-110P (220P) 58

59 W552_2 Wiring for ontrol Valves Proportional, Multiple Wiring, 120/230V ctuators: SY MFT SY MFT Hazard Identification Warnings and autions appear at appropriate sections throughout this manual. Read these carefully. UTION Indicates a potentially hazardous situation which, if not avoided, may result in minor or moderate injury. It may also be used to alert against unsafe practices. Indicates an action or condition that may cause irreversible damage to the actuator(s) or associated equipment. Equipment damage! Power consumption and input impedance must be observed. INSTLLTION NOTES Observe class 1 and class 2 wiring restrictions PPLITION NOTES Recommended twisted shielded pair for control wiring. Ground shielded wire at control panel chassis. Tape back ground at actuator. Use of feedback is optional. NOTES SY MFT (230MFT) aution: Power supply voltage. Power Supply om 120 V (N) / 230 V (L1) Power Supply Hot 120 V (H) / 230 V (L2) N L Internal Use Only ontrol Signal (+) Y P Tool Service Jack 1 Internal Use Only Internal Use Only ontrol Signal (-) 1 2 Internal Use Only Feedback 36 Feedback Signal (+) Feedback Signal (-) Not Used - U Internal Use Only 35 Not Used - 2 daption ddress E F ontrol Signal LS3 - (Open Indication) LS4 -F (losed Indication) ontact Rating: V Max. Feedback 36 G G 35 PE ontrol Signal (+) ontrol Signal (-) Feedback Signal (+) Feedback Signal (-) Not Used - Not Used - PE ctuator Y 1 U ctuator P Tool Service Jack SYx-120MFT SYx-230MFT daption SYx-120MFT SYx-230MFT N L 8 Internal Use Only Y1 9 Internal Use Only Y2 10 Internal Use Only Power Supply om 120 V (N) / 230 V (L1) Power Supply Hot 120 V (H) / 230 V (L2) Internal Use Only Internal Use Only 1 Internal Use Only 2 Internal Use Only 3 Internal Use Only ddress 8 Internal Use Only Y1 9 Internal Use Only Y2 10 Internal Use Only SY MFT SY MFT 59

60 F ctuators, On/Off imensions with 2-Way Valve F2WUIM_ H Models F24 US F24-S US F120 US F120-S US w/built-in ux. Switches w/built-in ux. Switches Technical ata ontrol on/off Power consumption F24(-S) US running 5 W holding 1.5 W F120(-S) US running 6 W holding 2.3 W Transformer sizing 10 V, class 2 power Electrical connection 3 ft, 18 G appliance cables (-S model has 2 cables) ½ conduit connector Electrical protection 120 V actuators double insulated Overload protection electronic throughout 0 to 95 rotation ngle of rotation 95 Position indication visual indicator Manual override hex crank Running time control 150 sec. independent of load spring < 20 sec. mbient temperature -22 F to 122 F [-30 to 50 ] Housing NEM 2 / IP54 gency listings UL 873, S 22.2 No. 24 certifi ed, E Noise level max. 45 d() F...-S US uxiliary switches 2 x SPT, V, UL listed, one switch is fixed at +5, one is adjustable 25 to 85 (double insulated) imensions (Inches) Fail Safe (psi) Valve Size (Max) H F 2*F F650H F650HU F665H 2½ F665HU 2½ F680H F680HU F6100HU F6125HU F SHP F SHP 2½ F SHP F SHP F SHP F SHP 2½ F SHP F SHP

61 10 10 F ctuators, On/Off imensions with 3-Way Valve 24 V Transformer W194 HS WGP11 Line 1 ommon Volts 2 + Hot 3 On/Off Wiring F24 US 2 W195-UX imensions (Inches) Fail Safe (psi) Valve Size (Max) H F 2*F F750H F750HU F765H 2½ F765HU 2½ F780HU uxiliary Switches Wiring iagrams 2 UTION Equipment damage! ctuators may be connected in parallel. Power consumption must be observed. 3 ctuators may also be powered by 24 V. 4 For end position indication, interlock control, fan startup, etc., F24-S US incorporates two built-in auxiliary switches: 2 x SPT, V, UL listed, one switch is fi xed at +5, one is adjustable 25 to 85. Meets culus or UL and S requirements without the need of an electrical ground connection. WRNING Live Electrical omponents! uring installation, testing, servicing and troubleshooting of this product, it may be necessary to work with live electrical components. Have a qualified licensed electrician or other individual who has been properly trained in handling live electrical components perform these tasks. Failure to follow all electrical safety precautions when exposed to live electrical components could result in death or serious injury. 61

62 FUP(-S)-X1, FXUP(-S)-X1 ctuators, On/Off imensions with 2-Way Valve F2WUIM_ H Models FUP-X1 FUP-S-X1 FXUP-X1 FXUP-S-X1 Technical ata Power supply Power consumption Transformer sizing Electrical connection FUP... FXUP V -20% / +10%, 50/60 Hz V ±10% running 7 W holding 3.5 W 7 24 V (class 2 power source) V V 3 ft, 18 G appliance cable, 1/2" conduit connector -S models: Two 3 ft, 18 gauge appliance cables with 1/2 conduit connectors 3 ft [1m], 10 ft [3m] or 16 ft [5m] 18 G appliance cable, with or without 1/2 conduit connector -S models: Two 3 ft [1m], 10 ft [3m] or 16 ft [5m] appliance cables with or without 1/2" conduit connectors Electronic throughout 0 to 95 rotation On/Off 180 in-lb [20 Nm] minimum spring reversible with W/W mounting Overload protection ontrol Torque irection of rotation Mechanical angle of rotation 95 (adjustable with mechanical end stop, 35 to 95 ) Running time motor < 75 sec spring F to 122 F [-20 to 50 ]; < F [-30 ] Position indication visual indicator, 0 to 95 (0 is full spring return position) Manual override 5 mm hex crank (³ ₁₆" llen), supplied Humidity max. 95% RH non-condensing mbient temperature -22 F to 122 F [-30 to 50 ] Storage temperature -40 F to 176 F [-40 to 80 ] Housing Nema 2, IP54, Enclosure Type2 Housing material Zinc coated metal and plastic casing gency listings culus acc. to UL /-2-14, N/S E :02, E acc. to 2004/108/E & 2006/95/E Noise level <50d() 75 seconds 62d() spring return Servicing maintenance free Quality standard ISO 9001 Weight 4.6 lbs (2.1 kg), 4.9 lbs (2.25 kg) with switches Rated Impulse Voltage 4kV, Type of action 1. (1.. for -S version), ontrol Pollution egree 3. FUP-S-X1, FXUP-S-X1 uxiliary switches 2 x SPT V, UL pproved one set at +10, one adjustable 10 to 90 imensions (Inches) Fail Safe (psi) Valve Size (Max) H F 2*F F650H F650HU F665H 2½ F665HU 2½ F680H F680HU F6100HU F6125HU F SHP F SHP 2½ F SHP F SHP F SHP F SHP 2½ F SHP F SHP F650VI F665VI 2½ F665VI 2½ F680VI

63 10 10 FUP(-S)-X1, FXUP(-S)-X1 ctuators, On/Off imensions with 3-Way Valve Wiring iagrams imensions (Inches) Fail Safe (psi) Valve Size (Max) H F 2*F F750H F750HU F765H 2½ F765HU 2½ F780HU F750VI F750VI F765VI 2½ Provide overload protection and disconnect as required. 2 UTION Equipment amage! ctuators may be connected in parallel. Power consumption and input impedance must be observed. 3 No ground connection is required. 4 For end position indication, interlock control, fan startup, etc., FUP-S-X1 and FXUP-S-X1 incorporates two built-in auxiliary switches: 2 x SPT, 3 V, UL pproved, one switch is fi xed at +10, one is adjustable 10 to 90. Meets culus requirements without the need of an electrical ground connection. WRNING Live Electrical omponents! uring installation, testing, servicing and troubleshooting of this product, it may be necessary to work with live electrical components. Have a qualifi ed licensed electrician or other individual who has been properly trained in handling live electrical components perform these tasks. Failure to follow all electrical safety precautions when exposed to live electrical components could result in death or serious injury. Typical Specification On/Off spring return damper actuators shall be direct coupled type which require no crank arm and linkage and be capable of direct mounting to a jackshaft up to a 1.05 diameter. The actuators must be designed so that they may be used for either clockwise or counterclockwise fail-safe operation. ctuators shall be protected from overload at all angles of rotation. If required, two SPT auxiliary switch shall be provided having the capability of one being adjustable. ctuators with auxiliary switches must be constructed to meet the requirements for ouble Insulation so an electrical ground is not required to meet agency listings. ctuators shall be culus approved and have a 5 year warranty, and be manufactured under ISO 9001 International Quality ontrol Standards. ctuators shall be as manufactured by elimo. On/Off wiring for FUP-X1, FXUP-X1 Wht lk FUP, FUP-S FXUP, FUP-S W066_F(X)UP W067_F(X)UP-S FUP-S FXUP-S uxiliary Switches for FUP-S-X1, FXUP-S-X1 63

64 10 10 F ctuators, Multi-Function Technology imensions with 2-Way Valve F2WUIM_ Models FX24-MFT-X1 FX24-MFT-S-X1 w/built-in ux. Switches 2*FX24-MFT-X1 2*FX24-MFT-S-X1 Technical ata Power supply 24 V, +/- 20%, 50/60 Hz 24 V, +20% / -10% Power running 7.5 W consumption holding 3 W Transformer sizing 10 V (lass 2 power source) Electrical connection FX... 3 ft [1m] default, 10 ft [3m] or 16 ft [5m] 18 G appliance or plenum cables, with or without 1/2 conduit connector -S models: two 3 ft [1m] default, 10 ft [3m] or 16 ft [5m] appliance cables with or without 1/2" conduit connectors Overload protection electronic throughout 0 to 95 rotation Operating range Y* 2 to 10 V, 4 to 20 m (default) variable (V, PWM, floating point, on/off) Input impedance 100 kω for 2 to 10 V (0.1 m) 500 Ω for 4 to 20 m 1500 Ω for PWM, floating point and on/off control Feedback output U* 2 to 10 V, 0.5 m max Torque minimum 180 in-lb (20 Nm) irection of spring reversible with cw/ccw mounting rotation* motor reversible with built-in switch Mechanical 95 (adjustable with mechanical end stop, 35 to 95 ) angle of rotation* Running time spring <20 -4 F to 122 F [-20 to 50 ]; < F [-30 ] motor* 150 seconds (default), variable (70 to 220 seconds) ngle of rotation off (default) adaptation Override control* min position = 0% mid. position = 50% max. position = 100% Position indication visual indicator, 0 to 95 (0 is spring return position) Manual override 5 mm hex crank (³ ₁₆" llen), supplied Humidity max. 95% RH, non-condensing mbient temperature -22 to 122 F (-30 to 50 ) Storage temperature -40 to 176 F (-40 to 80 ) Housing NEM 2, IP54, Enclosure Type 2 Housing material zinc coated metal and plastic casing Noise level 40d() 150 seconds, run time dependent 62d() spring return gency listings culus acc. to UL /-2-14, N/S E :02, E acc. to 2004/108/E & 2006/95/E Quality standard ISO 9001 Servicing maintenance free Weight 4.6 lbs. (1.9 kg), 4.9 lbs. (2 kg) with switch * Variable when configured with MFT options Rated Impulse Voltage 800V, Type of action 1. (1.. for -S version), ontrol Pollution egree 3. Programmed for 70 sec motor run time. t 150 sec motor run time, transformer sizing is 8.5 V and power consumption is 6 W running / 3 W holding. FX24-MFT-S-X1 uxiliary switches 64 2 x SPT V, UL approved one set at +10, one adjustable 10 to 90 H imensions (Inches) Fail Safe (psi) Valve Size (Max) H F 2*F F650H F650HU F665H 2½ F665HU 2½ F680H F680HU F6100HU F6125HU F SHP F SHP 2½ F SHP F SHP F SHP F SHP 2½ F SHP F SHP F650VI F665VI 2½ F680VI imensions with 3-Way Valve imensions (Inches) Fail Safe (psi) Valve Size (Max) H F 2*F F750H F750HU F765H 2½ F765HU 2½ F780HU F750VI F750VI F765VI 2½ HS WGP11

65 F ctuators, Multi-Function Technology Wiring iagrams 3 ctuators may also be powered by 24 V. 4 IN4004 or IN4007 diode (IN4007 supplied, elimo part number 40155). 5 Triac and can also be contact closures. ontrol signal may be pulsed from either the Hot (Source) or 6 ommon (Sink) 24 V line. Position feedback cannot be used with Triac sink controller. 7 The actuators internal common reference is not compatible. The ZG-R Ω resistor converts the 4 to 20 m control signal to 2 to 10 V, up to 2 actuators may be connected in parallel. Meets culus or UL and S requirements without the need of an electrical ground connection. WRNING Live Electrical omponents! uring installation, testing, servicing and troubleshooting of this product, it may be necessary to work with live electrical components. Have a qualified licensed electrician or other individual who has been properly trained in handling live electrical components perform these tasks. Failure to follow all electrical safety precautions when exposed to live electrical components could result in death or serious injury. V/4-20 m PWM W399_utterfly W399_utterfly 24 V Transformer Master 5 Master_Slave W399_utterfly Line Volts 3 ontrol Signal 2 to 10 V ( ) (+) lk (1) ommon Red (2) + Hot Wht (3) Y Input, 2 to 10 V Org (5) U Output 2 to 10 V W W Slave 5 lk (1) ommon Red (2) + Hot Wht (3) Y Input, 2 to 10 V Org (5) U W W On/Off control Floating Point control W399_utterfly W600_F_FX Master/Slave F24-MFT-S FX24-MFT-S-X1 FX24-MFT-S uxiliary Switches for FX24-MFT-S-X1 65

66 KRX24-3-T, KRX()24-3-T N4(H) NEM 2/NEM 4 ctuators, On/Off, Floating Point imensions with 2-Way Valve R_NEM_4_Linerawing Models KRX24-3-T KRX24-3-T N4 KR24-3-T N4H w/terminal block w/terminal block w/heater Technical ata ontrol on/off, fl oating point Power supply 24 V ± 20/-10% 50/60 Hz Power consumption running 12W / heater 33W holding 3W Transformer sizing 21 V (class 2 power source) / heater 36 V Electrical connection screw terminal (for 22 to 12 WG wire) Overload protection electronic throughout 0 to 90 rotation Input impedance 100 Ω at control input 1500 Ω fl oating point ngle of rotation 90 Position indication visual pointer (N4) Manual override internal push button (UL Type 4) external push buttom (UL Type 2) Running time 150 seconds (default) Fail-Safe 35 seconds Humidity 5 to 100% RH (UL Type 4) 5 to 95% RH non condensation (UL Type 2) mbient temperature -22 F to 122 F [-30 to 50 ] Storage temperature -40 F to 176 F [-40 to 80 ] Housing type UL Type 4/NEM 4/IP66 UL Type 2/NEM 2/IP54 Housing material Polycarbonate gency listings culus according to UL , UL and N/S E ; ertifi ed to IE/EN and IE/EN EM E according to 2004/108/E Quality standard ISO 9001 Servicing maintenance free H Valve Nominal imensions (Inches [mm]) Size Valve ody Inches N [mm] FLG F6100H 4" [52.1] 7.34 [186] 6.77 [172] [393] F07 F6125H 5" [52.8] 7.34 [186] 6.77 [172] [418] F07 F6150HU 6" [55.6] 7.34 [186] 6.77 [172] [418] F07 imensions without Housing 8.82 [224] 6.77 [172] Valve Nominal imensions (Inches [mm]) Size Valve ody Inches N [mm] FLG F6100H 4" [52.1] 5.81 [148] 2.64 [67.1] [337] F07 F6125H 5" [52.8] 5.81 [148] 2.64 [67.1] [362] F07 F6150HU 6" [55.6] 5.81 [148] 2.64 [67.1] [362] F07 R24_TP_7Linerawing 66

67 KRX24-3-T, KRX()24-3-T N4(H) NEM 2/NEM 4 ctuators, On/Off, Floating Point Electrical Installation Wiring iagrams Wiring diagram Note onnect via safety isolation transformer.! Parallel connection of other actuators possible. Note performance data for supply. able lengths Note When several actuators are connected in parallel, the maximum cable length must be divided by the number of actuators. T ~ T ~ Y U Y U L 2 L V V L tot 1 Provide overload protection and disconnect as required UTION Equipment amage! ctuators may be connected in parallel if not mechanically mounted to the same shaft. Power consumption and input impedance must be observed. Position feedback cannot be used with Triac sink controller. The actuator internal common reference is not compatible. ontrol signal may be pulsed from either the Hot (source) or the ommon (sink) 24 V line. ontact closures & also can be triacs. & should both be closed for triac source and open for triac sink. For triac sink the common connection from the actuator must be connected to the hot connection of the controller. Note There are no special restrictions on installation if the supply and data cable are routed separately. N L 230 V 24 V T Y U L 1 Meets UL requirements without the need of an electrical ground connection. WRNING Live Electrical omponents! uring installation, testing, servicing and troubleshooting of this product, it may be necessary to work with live electrical components. Have a qualifi ed licensed electrician or other individual who has been properly trained in handling live electrical components perform these tasks. Failure to follow all electrical safety precautions when exposed to live electrical components could result in death or serious injury. able colors: 1 = black 2 = red 3 = white 5 = orange = ctuator = ontrol unit L1 = elimo connecting cable, 1 m (4 x 0.75 mm 2 ) L2 = ustomer cable Ltot = Maximum cable length ross section L2 Max. cable length Ltot t = L1 + L2 Example for / 0.75 mm 2 <30 m <5 m 1 m (L1) + 4 m (L 2) 1.00 mm 2 <40 m <8 m 1 m (L1) + 7 m (L 2) 1.50 mm 2 <70 m <12 m 1 m (L1) + 11 m (L 2) 2.50 mm 2 <100 m <20 m 1 m (L1) + 19 m (L 2) T ~ = ctuator = ontrol unit L1 = elimo connecting cable, 1 m (4 x 0.75 mmm 2 ) On/Off control Floating Point control 67

68 KRX24-MFT-T, KRX()24-MFT-T N4(H) NEM 2/NEM 4 ctuators, Multi-Function Technology imensions with 2-Way Valve Models KRX24-MFT-T w/terminal block KRX24-MFT-T N4 w/terminal block KR24-MFT-T N4H w/heater Technical ata ontrol 2 to 10 V, 4 to 20 m (default) variable (V, fl oating point, on/off) Power supply 24 V ± 20% 50/60 Hz 24 V ± 10% Power consumption running 12 W / heater 33W holding 3 W Transformer sizing 21 V (class 2 power source) / heater 36 V Electrical connection screw terminal (for 22 to 12 WG wire) Overload protection electronic throughout 0 to 90 rotation Input impedance 100 kω (0.1 m) 500 Ω 1500 Ω (fl oating point, on/off) ngle of rotation 90 electronically variable Position indication visual pointer (N4) Manual override internal push button (UL Type 4) external push buttom (UL Type 2) Running time 150 seconds (default) variable (75 to 290 seconds) Fail-Safe 35 seconds Humidity 5 to 100% RH (UL Type 4) 5 to 95% RH non condensation (UL Type 2) mbient temperature -22 F to 122 F [-30 to 50 ] Storage temperature -40 F to 176 F [-40 to 80 ] Housing type UL Type 4/NEM 4/IP66 UL Type 2/NEM 2/IP54 Housing material Polycarbonate gency listings culus according to UL , UL and N/S E ; ertifi ed to IE/EN and IE/EN EM E according to 2004/108/E Quality standard ISO 9001 Servicing maintenance free H Valve Nominal imensions (Inches [mm]) Size Valve ody Inches N [mm] FLG F6100H 4" [52.1] 7.34 [186] 6.77 [172] [393] F07 F6125H 5" [52.8] 7.34 [186] 6.77 [172] [418] F07 F6150HU 6" [55.6] 7.34 [186] 6.77 [172] [418] F07 imensions without Housing 8.82 [224] 6.77 [172] Valve Nominal imensions (Inches [mm]) Size N Valve ody Inches FLG [mm] F6100H 4" [52.1] 5.81 [148] 2.64 [67.1] [337] F07 F6125H 5" [52.8] 5.81 [148] 2.64 [67.1] [362] F07 F6150HU 6" [55.6] 5.81 [148] 2.64 [67.1] [362] F07 R_NEM_4_Linerawing R24_TP_7Linerawing 68

69 KRX24-MFT-T, KRX()24-MFT-T N4(H) NEM 2/NEM 4 ctuators, Multi-Function Technology Wiring iagrams W399_08 1 Provide overload protection and disconnect as required. 2 UTION Equipment amage! ctuators may be connected in parallel if not mechanically mounted to the same shaft. Power consumption and input impedance must be observed. 3 ctuators may also be powered by 24 V. 4 Position feedback cannot be used with Triac sink controller. The actuator internal common reference is not compatible. 5 8 ontrol signal may be pulsed from either the Hot (source) or the ommon (sink) 24 V line. ontact closures & also can be triacs. & should both be closed for triac source and open for triac sink. V/4-20 m W399_08 9 For triac sink the common connection from the actuator must be connected to the hot connection of the controller. Meets UL requirements without the need of an electrical ground connection. The ZG-R Ω resistor may be used. PWM WRNING Live Electrical omponents! uring installation, testing, servicing and troubleshooting of this product, it may be necessary to work with live electrical components. Have a qualifi ed licensed electrician or other individual who has been properly trained in handling live electrical components perform these tasks. Failure to follow all electrical safety precautions when exposed to live electrical components could result in death or serious injury. W399_08 On/Off control Floating Point control W399_08 69

70 RX24-3-T, RX()24-3-T N4(H) NEM 2/NEM 4 ctuators, On/Off, Floating Point imensions with 2-Way Valve R_NEM_4_Linerawing Models RX24-3-T RX24-3-T N4 R24-3-T N4H w/terminal block w/terminal block w/heater Technical ata ontrol on/off, fl oating point Power supply 24 V ± 20/-10% 50/60 Hz 24 V ± 10% Power consumption running 9W / heater 29W holding 2W Transformer sizing 12 V (class 2 power source) / heater 27 V Electrical connection screw terminal (for 22 to 12 WG wire) Overload protection electronic throughout 0 to 90 rotation Input impedance 1000 Ω at control input ngle of rotation 90 Position indication visual pointer Manual override internal push button (UL Type 4) external push buttom (UL Type 2) Running time 35 seconds (default) Humidity 5 to 100% RH (UL Type 4) 5 to 95% RH non condensation (UL Type 2) mbient temperature -22 F to 122 F [-30 to 50 ] Storage temperature -40 F to 176 F [-40 to 80 ] Housing type UL Type 4/NEM 4/IP66 UL Type 2/NEM 2/IP54 Housing material Polycarbonate gency listings culus according to UL , UL and N/S E ; ertifi ed to IE/EN and IE/EN EM E according to 2004/108/E Quality standard ISO 9001 H Valve Nominal imensions (Inches [mm]) Size Valve ody Inches N [mm] FLG F6100H 4" [52.1] 7.34 [186] 6.77 [172] [393] F07 F6150HU 6" [55.6] 7.34 [186] 6.77 [172] [418] F07 imensions without Housing 8.82 [224] 6.77 [172] Valve Nominal imensions (Inches [mm]) Size Valve ody Inches N [mm] FLG F6100H 4" [52.1] 6.00 [152] 3.00 [76.2] [340] F07 F6150HU 6" [55.6] 6.02 [153] 3.02 [76.7] [344] F07 R24_TP_7Linerawing 70

71 RX24-3-T, RX()24-3-T N4(H) NEM 2/NEM 4 ctuators, On/Off, Floating Point Wiring iagrams 2 UTION Equipment damage! ctuators may be connected in parallel. Power consumption and input impedance must be observed. 4 ctuators may also be powered by 24 V. 5 ctuators with plenum rated cable do not have numbers on wires; use color codes instead. ctuators with appliance cables are numbered. Line Volts 24 V Transformer a open a closed The indication of direction is valid for switch position 1. a 4 lk (1) ommon Red (2) + Wht (3) R24-3 R24-3 W409 8 ontrol signal may be pulsed from either the Hot (Source) or ommon (Sink) 24 V line. On/Off ontrol 9 10 ontact closures & also can be triacs. & should both be closed for triac source and open for triac sink. For triac sink the ommon connection from the actuator must be connected to the Hot connection of the controller. Position feedback cannot be used with a Triac sink controller. The actuator internal common reference is not compatible. Line Volts ( ) 2 to 10 V Feedback Signal (+) 24 V Transformer lk (1) ommon Red (2) Hot + Wht (3) Y1 Input Pnk (4) Y2 Input Org (5) U Output 2 to 10V W400_floating_point Meets culus or UL and S requirements without the need of an electrical ground connection. WRNING Live Electrical omponents! uring installation, testing, servicing and troubleshooting of this product, it may be necessary to work with live electrical components. Have a qualified licensed electrician or other individual who has been properly trained in handling live electrical components perform these tasks. Failure to follow all electrical safety precautions when exposed to live electrical components could result in death or serious injury. WRNING Mechanical Precautions The mechanical end stops cannot be moved or repositioned. oing so will adversely effect the operation of the valve. The directional switch cannot be moved. Maintain Factory Settings Floating Point, Only R

72 RX24-MFT-T, RX24-MFT-T N4, RX24-MFT-T, RX()24-MFT-T N4(H) NEM 2/NEM 4 ctuators, Multi-Function Technology imensions with 2-Way Valve Models RX24-MFT-T w/terminal block RX24-MFT-T N4 w/terminal block RX24-MFT-T w/terminal block RX24-MFT-T N4 w/terminal block R24-MFT-T N4H w/heater Technical ata ontrol 2 to 10 V, 4 to 20 m (default) variable (V, fl oating point, on/off) Power supply 24 V ± 20% 50/60 Hz 24 V ± 10% Power consumption running 6.5 W / heater 27W holding 2.5 W Transformer sizing 9.5 V (class 2 power source) / heater 25 V Electrical connection screw terminal (for 22 to 12 WG wire) Overload protection electronic throughout 0 to 90 rotation Input impedance 100 kω for 2 to 10 V (0.1 m) 500 Ω for 4 to 20 m 1000 Ω for fl oating point and on-off control ngle of rotation 90 electronically variable Position indication visual pointer Manual override internal push button (UL Type 4) external push buttom (UL Type 2) Running time RX seconds RX seconds Humidity 5 to 100% RH (UL Type 4) 5 to 95% RH non condensation (UL Type 2) mbient temperature -22 F to 122 F [-30 to 50 ] Storage temperature -40 F to 176 F [-40 to 80 ] Housing type UL Type 4/NEM 4/IP66 UL Type 2/NEM 2/IP54 Housing material Polycarbonate gency listings culus according to UL , UL and N/S E ; ertifi ed to IE/EN and IE/EN " EM E according to 2004/108/E Quality standard ISO 9001 H Valve Nominal imensions (Inches [mm]) Size Valve ody Inches N [mm] FLG F6100H 4" [52.1] 7.34 [186] 6.77 [172] [393] F07 F6150HU 6" [55.6] 7.34 [186] 6.77 [172] [418] F07 imensions without Housing 8.82 [224] 6.77 [172] Valve Nominal imensions (Inches [mm]) Size Valve ody Inches N [mm] FLG F6100H 4" [52.1] 5.81 [148] 2.64 [67.1] [337] F07 F6150HU 6" [55.6] 5.81 [148] 2.64 [67.1] [362] F07 R_NEM_4_Linerawing R24_TP_7Linerawing 72

73 RX24-MFT-T, RX24-MFT-T N4, RX24-MFT-T, RX()24-MFT-T N4(H) NEM 2/NEM 4 ctuators, Multi-Function Technology Wiring iagrams 2 UTION Equipment damage! ctuators may be connected in parallel. Power consumption and input impedance must be observed. 3 ctuators may also be powered by 24 V. ctuators with plenum rated cable do not have numbers on wires; use 5 color codes instead. ctuators with appliance cables are numbered. ontrol signal may be pulsed from either the Hot (source) 8 or the ommon (sink) 24 V line. ontact closures & also can be triacs. 9 & should both be closed for triac source and open for triac sink. For triac sink the ommon connection from the actuator must be connected to the Hot connection of the controller. Position feedback 10 cannot be used with a Triac sink controller. The actuator internal common reference is not compatible. 12 IN4004 or IN4007 diode. (IN4007 supplied, elimo part number 40155). WRNING Mechanical Precautions The mechanical end stops cannot be moved or repositioned. oing so will adversely effect the operation of the valve. The directional switch cannot be moved. Maintain Factory Settings On/Off ontrol 24 V Transformer W538 The ZG-R Ω resistor converts the 4 to 20 m control signal to 2 to 10 V, up to 2 actuators may be connected in parallel. WRNING Live Electrical omponents! uring installation, testing, servicing and troubleshooting of this product, it may be necessary to work with live electrical components. Have a qualified licensed electrician or other individual who has been properly trained in handling live electrical components perform these tasks. Failure to follow all electrical safety precautions when exposed to live electrical components could result in death or serious injury. Line Volts 8 ( ) 2 to 10 V Feedback Signal (+) Floating Point, Only 9 12 lk (1) ommon Red (2) + Hot Wht (3) Y1 Input (5) U Output 2 to 10V W W...MFT W538 V/4-20 m 73

74 10 GK ctuators, On/Off, Floating Point imensions with 2-Way Valve M_GM_LineRevised H Models GKR24-3-X1 GKR GK24-3-X1 Technical ata Power supply Power consumption Transformer sizing Electrical connection Overload protection Operation range Y Input impedance Feedback output U 24V ±20% 50/60Hz 12W (3W) 21V (class 2 power source) 18 G plenum rated cable ½" conduit connector protected NEM 2 (IP54) 3 ft [1m] 10 ft [3m] 16 ft [5m] electronic throughout 0 to 95 rotation on/off, fl oating point 100kΩ (0.1 m), 500Ω 1500Ω (fl oating point, on/off) 2 to 10V, 0.5m max, V variable ngle of rotation max. 95, adjustable with mechanical stop electronically variable irection of rotation reversible with switch Fail-safe position adjustable with dial or tool 0 to 100% in 10% increments Position indication refl ective visual indicator (snap-on) Manual override external push button Running time normal operation fail-safe 150 seconds (default), variable 90 to 150 seconds 35 seconds Humidity 5 to 95% RH non-condensing (EN ) mbient temperature -22 F to +122 F [-30 to +50 ] Storage temperature -40 F to +176 F [-40 to +80 ] Housing NEM2, IP54, UL enclosure type 2 Housing material UL94-5V gency list culus acc. to UL /-2-14 N/S E :02 E acc. to 2004/108/EE and 2006/95/E Noise level < 45d() Servicing maintenance free Quality standard ISO 9001 imensions (Inches) Non-Fail Safe (psi) Valve Size (Max) H GK F680H F6100HU F6125HU F SHP F SHP 2½ F SHP F SHP F SHP F SHP 2½ F SHP F SHP F6100VI imensions with 3-Way Valve imensions (Inches) Non-Fail Safe (psi) Valve Size (Max) H GK F765H 2½ F780HU F SHP F SHP 2½ F SHP F SHP F765VI 2½ F780VI F7100VI Single_utterfl y 0 74

75 GK ctuators, On/Off, Floating Point Electrical Installation Wiring iagrams Wiring diagram Note onnect via safety isolation transformer.! Parallel connection of other actuators possible. Note performance data for supply. T ~ Y U V V 1 Provide overload protection and disconnect as required. 3 ctuators may also be powered by 24 V. able lengths T ~ Y U L 2 L tot Position feedback cannot be used with Triac sink controller. The actuator internal common reference is not compatible. ontrol signal may be pulsed from either the Hot (source) or the ommon (sink) 24 V line. ontact closures & also can be triacs. & should both be closed for triac source and open for triac sink. For triac sink the common connection from the actuator must be connected to the hot connection of the controller. Note When several actuators are connected in parallel, the maximum cable length must be divided by the number of actuators N L 230 V 24 V T Y L 1 U Meets UL requirements without the need of an electrical ground connection. WRNING Live Electrical omponents! uring installation, testing, servicing and troubleshooting of this product, it may be necessary to work with live electrical components. Have a qualifi ed licensed electrician or other individual who has been properly trained in handling live electrical components perform these tasks. Failure to follow all electrical safety precautions when exposed to live electrical components could result in death or serious injury. Note There are no special restrictions on installation if the supply and data cable are routed separately L 1 NOTE: Wiring diagrams shown are for single actuator mounted solutions able colors: 1 = black 2 = red 3 = white 5 = orange = ctuator = ontrol unit L1 = elimo connecting cable, 1 m (4 x 0.75 mm 2 ) L2 = ustomer cable Ltot = Maximum cable length ross section L2 Max. cable length Ltot t = L1 + L2 Example for / 0.75 mm 2 <30 m <5 m 1 m (L1) + 4 m (L 2) 1.00 mm 2 <40 m <8 m 1 m (L1) + 7 m (L 2) 1.50 mm 2 <70 m <12 m 1 m (L1) + 11 m (L 2) 2.50 mm 2 <100 m <20 m 1 m (L1) + 19 m (L 2) T ~ = ctuator = ontrol unit L1 = elimo connecting cable, 1 m (4 x 0.75 mmm 2 ) On/Off control W399_10 W399_10 Floating Point control 75

76 10 GK ctuators, Multi-Function Technology imensions with 2-Way Valve M_GM_LineRevised H Models GKRX24-MFT-X1 GKX24-MFT-X1 Technical ata Power supply Power consumption Transformer sizing Electrical connection Overload protection Operation range Y GKX24-MFT-X1 24V ±20% 50/60Hz 24V ±10% 12W (3W) 21V (class 2 power source) 18 G plenum rated cable ½" conduit connector protected NEM 2 (IP54) 3 ft [1m] 10 ft [3m] 16 ft [5m] electronic throughout 0 to 95 rotation 2 to 10 V, 4 to 20m (default) variable (V,PWM, fl oating point, on/off) Input impedance 100 kω (0.1 m), 500 Ω 1500 Ω (PWM, fl oating point, on/off) Feedback output U 2 to 10V, 0.5m max, V variable ngle of rotation max. 95, adjustable with mechanical stop electronically variable irection of rotation reversible with switch Fail-safe position adjustable with dial or tool 0 to 100% in 10% increments Position indication refl ective visual indicator (snap-on) Manual override external push button Running time normal operation fail-safe 95 seconds (default), variable 90 to 150 seconds 35 seconds Humidity 5 to 95% RH non-condensing (EN ) mbient temperature -22 F to +122 F [-30 to +50 ] Storage temperature -40 F to +176 F [-40 to +80 ] Housing NEM2, IP54, UL enclosure type 2 Housing material UL94-5V gency list culus acc. to UL /-2-14 N/S E :02 E acc. to 2004/108/EE and 2006/95/E Noise level < 45d() Servicing maintenance free Quality standard ISO 9001 Note: GKR ctuators are on 2-way valves GKX ctuators are on 3-way valves imensions (Inches) Non-Fail Safe (psi) Valve Size (Max) H GK F680H F6100HU F6125HU F6150HU F SHP F SHP 2½ F SHP F SHP F SHP F SHP 2½ F SHP F SHP F6100VI imensions with 3-Way Valve imensions (Inches) Non-Fail Safe (psi) Valve Size (Max) H GK 2*GK F780HU F7100HU F7125HU F7150HU F SHP F SHP 2½ F SHP F765VI 2½ F780VI F7100VI Single_utterfl y 76

77 GK ctuators, Multi-Function Technology Wiring iagrams 1 Provide overload protection and disconnect as required. W399_utterfly 3 ctuators may also be powered by 24 V. 4 Position feedback cannot be used with Triac sink controller. The actuator internal common reference is not compatible. 5 ontrol signal may be pulsed from either the Hot (source) or the ommon (sink) 24 V line. 8 9 ontact closures & also can be triacs. & should both be closed for triac source and open for triac sink. For triac sink the common connection from the actuator must be connected to the hot connection of the controller. Meets UL requirements without the need of an electrical ground connection. V/4-20 m W399_utterfly The ZG-R Ω resistor may be used. WRNING Live Electrical omponents! uring installation, testing, servicing and troubleshooting of this product, it may be necessary to work with live electrical components. Have a qualifi ed licensed electrician or other individual who has been properly trained in handling live electrical components perform these tasks. Failure to follow all electrical safety precautions when exposed to live electrical components could result in death or serious injury. NOTE: Wiring diagrams shown are for single actuator mounted solutions PWM W399_utterfly On/Off control Floating Point control W399_utterfly 77

78 10 M/R Series ctuators, On/Off, Floating Point imensions with 2-Way Valve R_LineRevised H Models M24-3-X1 R24-3-X1 R Technical ata Power supply 24 V ± 20% 50/60 Hz 24 V ± 10% Power consumption running 2.0 W holding 0.2 W Transformer sizing 5.5 V (class 2 power source) Electrical connection 3 ft, 18 G plenum rated cable ½ conduit connector Overload protection electronic throughout 0 to 95 rotation ontrol on/off, fl oating point Input impedance 600 Ω ngle of rotation 95, adjustable with mechanical stop irection of rotation reversible with protected switch Position indication handle Manual override external push button Running time 95 seconds Humidity 5 to 95% RH non condensing (EN ) mbient temperature -22 F to +122 F [-30 to +50 ] Storage temperature -40 F to +176 F [-40 to +80 ] Housing NEM 2/IP54 Housing material UL94-5V gency listings culus according to UL /-2-14, N/S E , S 22.2 No , E according to 89/336/EE (and 2006/95/E for line voltage and/or -S versions) Noise level <45d() Quality standard ISO 9001 Note: R ctuators are on 2-way valves M ctuators are on 3-way valves imensions (Inches) Non-Fail Safe (psi) Valve Size (Max) H H HU F650H(U) F665H(U) 2½ F680HU F650VI F665VI 2½ imensions with 3-Way Valve imensions (Inches) Non-Fail Safe (psi) Valve Size (Max) H H HU F750H F765HU 2½ F750VI Single_utterfl y 78

79 M/R Series ctuators, On/Off, Floating Point Wiring iagrams j y 24 V Transformer W557_10 2 UTION Equipment damage! ctuators may be connected in parallel. Power consumption and input impedance must be observed. 4 ctuators may also be powered by 24 V. Line Volts a open a closed The indication of direction is valid for switch position 1. a lk (1) ommon Red (2) + Wht (3) M24-3-X1 Meets culus or UL and S requirements without the need of an electrical ground connection. On/Off control WRNING Live Electrical omponents! uring installation, testing, servicing and troubleshooting of this product, it may be necessary to work with live electrical components. Have a qualified licensed electrician or other individual who has been properly trained in handling live electrical components perform these tasks. Failure to follow all electrical safety precautions when exposed to live electrical components could result in death or serious injury. Line Volts 24 V Transformer lk (1) ommon Red (2) + Wht (3) + W557_10 The indication of direction is valid for switch position M24-3-X1 Floating Point or On/Off control 79

80 10 M/R Series ctuators, Multi-Function Technology imensions with 2-Way Valve R_LineRevised H Models MX24-MFT-X1 RX24-MFT-X1 R24-MFT-5 imensions (Inches) Valve Size (Max) H F650H(U) F665H(U) 2½ F680HU F650VI F665VI 2½ imensions with 3-Way Valve Non-Spring Return (psi) Technical ata Power supply 24 V ± 20% 50/60 Hz 24 V ± 10% Power consumption running 4 W holding 1.25 W Transformer sizing 6 V (class 2 power source) Electrical connection 3 ft [1m], 10 ft [3m], 16 ft [5m] 18 G plenum rated cable ½ conduit connector Overload protection electronic throughout 0 to 95 rotation Operating range Y 2 to 10 V, 4 to 20 m (default) variable (V, PWM, fl oating point, on/off) Input impedance 100k Ω (0.1 m), 500 Ω 1500 Ω (PWM, fl oating point, on/off) Feedback output U 2 to 10 V, 0.5 m max V variable ngle of rotation 95 electronically variable irection of rotation reversible with protected switch Position indication handle Manual override external push button Running time 150 seconds (default) variable (90 to 350 secs) Humidity 5 to 95% RH non condensing (EN ) mbient temperature -22 F to +122 F [-30 to +50 ] Storage temperature -40 F to +176 F [-40 to +80 ] Housing NEM 2/IP54 Housing material UL94-5V gency listings culus according to UL /-2-14, N/S E , S 22.2 No , E according to 89/336/EE Noise level <45d() Quality standard ISO 9001 Rated impulse voltage 4kV, ontrol pollution degree 3, Type of action 1 imensions (Inches) Non-Fail Safe (psi) Valve Size (Max) H H HU F750H F765HU 2½ F750VI Single_utterfl y 80

81 M/R Series ctuators, Multi-Function Technology Wiring iagrams 3 ctuators may also be powered by 24 V Position feedback cannot be used with Triac sink controller. The actuator internal common reference is not compatible. ontrol signal may be pulsed from either the Hot (source) or the ommon (sink) 24 V line. ontact closures & also can be triacs. & should both be closed for triac source and open for triac sink. For triac sink the common connection from the actuator must be connected to the hot connection. The ZG-R Ω resistor converts the 4 to 20 m control signal to 2 to 10 V, up to 2 actuators may be connected in parallel. WRNING Live Electrical omponents! uring installation, testing, servicing and troubleshooting of this product, it may be necessary to work with live electrical components. Have a qualified licensed electrician or other individual who has been properly trained in handling live electrical components perform these tasks. Failure to follow all electrical safety precautions when exposed to live electrical components could result in death or serious injury. Two Position Line Volts 24 V/ Transformer Position ( ) Feedback V (+) Line Volts 24 V Transformer to 10 V Feedback Signal 11 a irection of rotation switch W W W W lk (1) ommon Red (2) Hot Wht (3) Y Input Org (5) U Output 3 lk (1) ommon Red (2) Hot + 10 Wht (3) Y1 Input Pnk (4) Y2 Input Org (5) U Output 2 to 10V W558_utterfly W558_utterfly Floating Point Line Volts ontrol Signal 4 to 20 m or 2 to 10 V 24 V Transformer ( ) (+) Ω 500Ω 1/4 watt lk (1) ommon Red (2) + Hot Wht (3) Y 1 Input, 2 to 10V Org (5) U Output, 2 to 10V W558_utterfly W W V/4-20 m PWM Line Volts 24 V Transformer ( only) Position Feedback V ( ) (+) 8 lk (1) ommon Red (2) + Hot Wht (3) Y Input Org (5) U Output W558_utterfly 81

82 GM/GR ctuators, On/Off, Floating Point imensions with 2-Way Valve M_GM_LineRevised H Models GM24-3-X1 GR24-3-X1 GR GR Technical ata Power supply 24 V ± 20% 50/60 Hz 24 V ± 10% Power consumption running 4.0 W holding 2 W Transformer sizing 6 V (class 2 power source) Electrical connection 3 ft, 18 G appliance cable, 1/2 conduit connector Overload protection electronic throughout 0 to 95 rotation ontrol signal On/Off, Floating Point Input impedance 600 Ω ngle of rotation mechanically limited to 95 irection of rotation reversible with switch / Position indication 0 to 1 and reversible indicator Running time 150 sec. Humidity 5 to 95% RH non-condensing mbient temperature -22 F to 122 F [-30 to 50 ] Storage temperature -40 F to 176 F [-40 to 80 ] Housing NEM 2/IP54 Housing material UL94-5V (fl ammability rating) gency listings culus according to UL /-2-14, N/S E , S 22.2 No.24-93, E according to 89/336/EE Noise level max. 45 d () Servicing maintenance free Quality standard ISO 9001 Note: GR ctuators are on 2-way valves GM ctuators are on 3-way valves imensions (Inches) Non-Fail Safe (psi) Valve Size (Max) H GM 2*GM F680H F6100H F6100HU F6125HU F6150HU F SHP F SHP 2½ F SHP F SHP F SHP F SHP 2½ F SHP F SHP F665VI 2½ F680VI F6100VI

83 GM/GR ctuators, On/Off, Floating Point imensions with 3-Way Valve Wiring iagrams UTION Equipment damage! ctuators may be connected in parallel. Power consumption and input impedance must be observed. 3 ctuators may also be powered by 24 V. 5 ctuators with plenum rated cable do not have numbers on wires; use color codes instead. ctuators with appliance cables are numbered. imensions (Inches) Non-Fail Safe (psi) Valve Size (Max) H GM 2*GM F765H 2½ F780H F780HU F7100HU F7125HU F7150HU F SHP F SHP 2½ F SHP F SHP F SHP F SHP 2½ F SHP F SHP F750VI F765VI 2½ F780VI Meets culus or UL and S requirements without the need of an electrical ground connection. WRNING Live Electrical omponents! uring installation, testing, servicing and troubleshooting of this product, it may be necessary to work with live electrical components. Have a qualified licensed electrician or other individual who has been properly trained in handling live electrical components perform these tasks. Failure to follow all electrical safety precautions when exposed to live electrical components could result in death or serious injury. On/Off Line Volts 24 V Transformer a open a closed The indication of direction is valid for switch position 1. j y 24 V Transformer a lk (1) ommon Red (2) + Wht (3) GM24-3-X1 W559 W559 Floating Point Line Volts The indication of direction is valid for switch position 1. lk (1) ommon Red (2) + Wht (3) GM24-3-X1 83

84 GM/GR ctuators, Multi-Function Technology imensions with 2-Way Valve M_GM_LineRevised Models GMX24-MFT-X1 GRX24-MFT-X1 GR24-MFT-5 GRX24-MFT-7 Technical ata Power supply 24 V ± 20% 50/60 Hz 24 V ± 10% Power consumption running 4.5 W holding 2 W Transformer sizing 7 V (class 2 power source) Electrical connection 3 ft, 18 G appliance cable, 1/2 conduit connector Overload protection electronic throughout 0 to 95 rotation ontrol signal 2 to 10 V, 4 to 20 m (with 500 Ω, 1/4 W resistor) ZG-R01 Input impedance 100 k Ω for 2 to 10 V (0.1 m) 500 Ω for 4 to 20 m 750 Ω for PWM 1500 Ω for on/off and fl oating point ngle of rotation mechanically limited to 95 irection of rotation reversible with switch / Position indication 0 to 1 and reversible indicator Running time 150 seconds Humidity 5 to 95% RH non-condensing mbient temperature -22 F to 122 F [-30 to 50 ] Storage temperature -40 F to 176 F [-40 to 80 ] Housing NEM 2/IP54 Housing material UL94-5V (fl ammability rating) gency listings culus according to UL /-2-14, N/S E , S 22.2 No.24-93, E according to 89/336/EE Noise level max. 45 d() Servicing maintenance free Quality standard ISO 9001 H imensions (Inches) Non-Fail Safe (psi) Valve Size (Max) H GM 2*GM F680H F6100H F6100HU F6125HU F6150HU F SHP F SHP 2½ F SHP F SHP F SHP F SHP 2½ F SHP F SHP F665VI 2½ F680VI F6100VI imensions with 3-Way Valve Non-Fail Safe imensions (Inches) (psi) Valve Size (Max) H GM 2*GM F765H 2½ F780H F780HU F7100H F7100HU F7125HU F7150HU F SHP F SHP 2½ F SHP F SHP F SHP 2½ F SHP F SHP F750VI F765VI 2½ F780VI

85 GM/GR ctuators, Multi-Function Technology Wiring iagrams 3 ctuators may also be powered by 24 V ctuators with plenum rated cable do not have numbers on wires; use color coded instead. ctuators with appliance rated cable use numbers. ontrol signal may be pulsed from either the Hot (Source) or ommon (Sink) 24 V line. For triac sink the ommon connection from the actuator must be connected to the Hot connection of the controller. Line Volts ontrol Signal 4 to 20 m or 2 to 10 V 24 V Transformer ( ) (+) Ω 500Ω 1/4 watt lk (1) ommon Red (2) + Hot Wht (3) Y 1 Input, 2 to 10V Org (5) U Output, 2 to 10V W W W545_No_2 V/4-20 m Meets culus or UL and S requirements without the need of an electrical ground connection. ontact closures & also can be triacs. & should 9 both be closed for triac source and open for triac sink. Position feedback cannot be used with a Triac sink controller. The 11 actuator internal common reference is not compatible. WRNING Live Electrical omponents! uring installation, testing, servicing and troubleshooting of this product, it may be necessary to work with live electrical components. Have a qualified licensed electrician or other individual who has been properly trained in handling live electrical components perform these tasks. Failure to follow all electrical safety precautions when exposed to live electrical components could result in death or serious injury. Line Volts 3 ontrol Signal 2 to 10 V 24 V Transformer ( ) (+) Master lk (1) ommon Red (2) + Hot Wht (3) Y Input, 2 to 10 V Org (5) U Output 2 to 10 V W W Slave W W 5 5 lk (1) ommon Red (2) + Hot Wht (3) Y Input, 2 to 10 V Org (5) U Master_Slave Two Position Floating Point PWM Line Volts 24 V/ Transformer Position ( ) Feedback V (+) Line Volts Line Volts 24 V Transformer 8 2 to 10 V Feedback Signal 9 11 W W 5 a irection of rotation switch W W 5 24 V Transformer ( only) Position Feedback V ( ) (+) 8 3 lk (1) ommon Red (2) Hot Wht (3) Y Input Org (5) U Output 3 lk (1) ommon Red (2) Hot + 10 Wht (3) Y 1 Input Pnk (4) Y 2 Input Org (5) U Output 2 to 10V lk (1) ommon Red (2) + Hot Wht (3) Y Input Org (5) U Output W545_No_2 W545_No_2 W545_No_2 Master/Slave 85

86 GRX()24-3-T N4(H) NEM 4 ctuators, On/Off, Floating Point imensions with 2-Way Valve Models GRX24-3-T N4 GR24-3-T N4H w/terminal block w/heater Technical ata ontrol on/off, fl oating point Power supply 24 V ± 20% 50/60 Hz 24 V ± 10% Power consumption running 8W / heater 29W holding 2.5W Transformer sizing 11 V (class 2 power source) / heater 26 V Electrical connection screw terminal (for 22 to 12 WG wire) Overload protection electronic throughout 0 to 90 rotation Input impedance 1000 Ω at control input ngle of rotation 90, adjustable with mechanical stop Position indication visual pointer Manual override internal push button (UL Type 4) Running time 35 seconds (default) Humidity 5 to 100% RH (UL Type 4) mbient temperature -22 F to 122 F [-30 to 50 ] Storage temperature -40 F to 176 F [-40 to 80 ] Housing type UL Type 4/NEM 4/IP66 Housing material Polycarbonate gency listings culus according to UL , UL and N/S E ; ertifi ed to IE/EN and IE/EN EM E according to 2004/108/E Quality standard ISO 9001 H Valve ody Valve Nominal Size N Inches [mm] imensions (Inches [mm]) FLG F650H/HU 2" [41.9] [266] 3.62 [92] [481] F05 F665H/HU 2.5" [44.7] [266] 3.62 [92] [495] F05 F680H/HU 3" [45.2] [266] 3.62 [92] [501] F05 F6100HU 4" [52.1] [266] 3.62 [92] [520] F07 F6125HU 5" [54.4] [266] 3.62 [92] [533] F07 GR_NEM_4_Linerawing 86

87 GRX()24-3-T N4(H) NEM 4 ctuators, On/Off, Floating Point Wiring iagrams 24 V Transformer 4 W409 2 UTION Equipment damage! ctuators may be connected in parallel. Power consumption and input impedance must be observed. 4 ctuators may also be powered by 24 V. 5 ctuators with plenum rated cable do not have numbers on wires; use color codes instead. ctuators with appliance cables are numbered. Line Volts a open a closed The indication of direction is valid for switch position 1. a lk (1) ommon Red (2) + Wht (3) GR24-3 R24-3 On/Off ontrol Meets culus or UL and S requirements without the need of an electrical ground connection. Use suitable flexible metallic conduit or its equivalent with the conduit fi tting. WRNING Live Electrical omponents! uring installation, testing, servicing and troubleshooting of this product, it may be necessary to work with live electrical components. Have a qualified licensed electrician or other individual who has been properly trained in handling live electrical components perform these tasks. Failure to follow all electrical safety precautions when exposed to live electrical components could result in death or serious injury. Floating Point, Only Line Volts 24 V Transformer lk (1) ommon Red (2) Hot + Wht (3) Y1 Input Pnk (4) Y2 Input GR24-3 W400_floating_point WRNING Mechanical Precautions The mechanical end stops cannot be moved or repositioned. oing so will adversely effect the operation of the valve. The directional switch cannot be moved. Maintain Factory Settings 87

88 GRX()24-MFT-T N4(H) NEM 4 ctuators, Multi-Function Technology imensions with 2-Way Valve Models GRX24-MFT-T N4 GR24-MFT-T N4H w/terminal block w/heater Technical ata ontrol 2 to 10 V, 4 to 20 m (default) variable (V, fl oating point, on/off) Power supply 24 V ± 20% 50/60 Hz 24 V ± 10% Power consumption running 8 W / heater 29W holding 2.5 W Transformer sizing 11 V (class 2 power source) / heater 24 V Electrical connection screw terminal (for 22 to 12 WG wire) Overload protection electronic throughout 0 to 90 rotation Input impedance 100 kω for 2 to 10 V (0.1 m) 500 Ω for 4 to 20 m 1000 Ω for fl oating point and on-off control ngle of rotation 90, adjustable with mechanical stop electronically variable Position indication visual pointer Manual override internal push button (UL Type 4) Running time 150 seconds (default) variable (75 to 290 seconds) Humidity 5 to 100% RH (UL Type 4) mbient temperature -22 F to 122 F [-30 to 50 ] Storage temperature -40 F to 176 F [-40 to 80 ] Housing type UL Type 4/NEM 4/IP66 Housing material Polycarbonate gency listings culus according to UL , UL and N/S E ; ertifi ed to IE/EN and IE/EN EM E according to 2004/108/E Quality standard ISO 9001 H Valve Nominal imensions (Inches [mm]) Size Valve ody Inches N [mm] FLG F650H/HU 2" [41.9] [266] 3.62 [92] [481] F05 F665H/HU 2.5" [44.7] [266] 3.62 [92] [495] F05 F680H/HU 3" [45.2] [266] 3.62 [92] [501] F05 F6100HU 4" [52.1] [266] 3.62 [92] [520] F07 F6125HU 5" [54.4] [266] 3.62 [92] [533] F07 GR_NEM_4_Linerawing 88

89 GRX()24-MFT-T N4(H) NEM 4 ctuators, Multi-Function Technology Wiring iagrams W538 2 UTION Equipment damage! ctuators may be connected in parallel. Power consumption and input impedance must be observed. 3 ctuators may also be powered by 24 V ctuators with plenum rated cable do not have numbers on wires; use color codes instead. ctuators with appliance cables are numbered. ontrol signal may be pulsed from either the Hot (source) or the ommon (sink) 24 V line. ontact closures & also can be triacs. & should both be closed for triac source and open for triac sink. For triac sink the ommon connection from the actuator must be connected to the Hot connection of the controller. Position feedback cannot be used with a Triac sink controller. The actuator internal common reference is not compatible. On/Off control 24 V Transformer Line Volts lk (1) ommon Red (2) + Hot Wht (3) Y1 Input 12 IN4004 or IN4007 diode. (IN4007 supplied, elimo part number 40155). 8 ( ) 2 to 10 V Feedback Signal (+) 9 12 (5) U Output 2 to 10V The ZG-R Ω resistor converts the 4 to 20 m control signal to 2 to 10 V, up to 2 actuators may be connected in parallel. W W WRNING Live Electrical omponents! uring installation, testing, servicing and troubleshooting of this product, it may be necessary to work with live electrical components. Have a qualified licensed electrician or other individual who has been properly trained in handling live electrical components perform these tasks. Failure to follow all electrical safety precautions when exposed to live electrical components could result in death or serious injury. Floating Point...MFT W538 WRNING Mechanical Precautions The mechanical end stops cannot be moved or repositioned. oing so will adversely effect the operation of the valve. The directional switch cannot be moved. Maintain Factory Settings V/4-20 m 89

90 GMX()24-3-T-X1 N4(H) NEM 4 ctuators, On/Off, Floating Point imensions with 2-Way Valve ZM0825 Models GMX24-3-T-X1 N4 w/terminal block GM24-3-T-X1 N4H w/heater Technical ata ontrol on/off, fl oating point Power supply 24 V ± 20% 50/60 Hz 24 V ± 10% Power consumption running 8W / heater 28W holding 2.5W Transformer sizing 11 V (class 2 power source) / heater 26 V Electrical connection screw terminal (for 22 to 12 WG wire) Overload protection electronic throughout 0 to 95 rotation Input impedance 1000 Ω at control input ngle of rotation 95, adjustable with mechanical stop electronically variable irection of rotation reversible with Position indication visual pointer Manual override internal push button (UL Type 4) Running time 35 seconds (default) Humidity 5 to 100% RH (UL Type 4) mbient temperature -22 F to 122 F [-30 to 50 ] Storage temperature -40 F to 176 F [-40 to 80 ] Housing type UL Type 4/NEM 4/IP66 Housing material Polycarbonate gency listings culus according to UL , UL and N/S E ; ertifi ed to IE/EN and IE/EN EM E according to 2004/108/E Quality standard ISO 9001 Valve Nominal imensions (Inches [mm]) Size Valve ody Inches N [mm] F SHP 2" [44.5] 3.62 [92] [266] [440] F SHP 2.5" [47.8] 3.62 [92] [266] [440] F SHP 3" [48.8] 3.62 [92] [266] [459] F SHP 4" [54.1] 3.62 [92] [266] [478] F SHP 2" [44.5] 3.62 [92] [266] [440] F SHP 2.5" [47.8] 3.62 [92] [266] [440] F SHP 3" [48.8] 3.62 [92] [266] [459] F SHP 4" [54.1] 3.62 [92] [266] [478] imensions with 3-Way Valve Valve Nominal imensions (Inches [mm]) Size Valve ody Inches N [mm] F SHP 2" [44.5] 3.62 [92] [266] [440] F SHP 2.5" [47.8] 3.62 [92] [266] [440] F SHP 3" [48.8] 3.62 [92] [266] [459] F SHP 4" [54.1] 3.62 [92] [266] [478] F SHP 2" [44.5] 3.62 [92] [266] [440] F SHP 2.5" [47.8] 3.62 [92] [266] [440] F SHP 3" [48.8] 3.62 [92] [266] [459] F SHP 4" [54.1] 3.62 [92] [266] [478] Note: Most F7 versions use dual actuators. ZM

91 GMX()24-3-T-X1 N4(H) NEM 4 ctuators, On/Off, Floating Point imensions with 3-Way Valve Wiring iagrams ZM UTION Equipment damage! ctuators may be connected in parallel. Power consumption and input impedance must be observed. 3 ctuators may also be powered by 24 V. 5 ctuators with plenum rated cable do not have numbers on wires; use color codes instead. ctuators with appliance cables are numbered. Valve Nominal imensions (Inches [mm]) Size Valve ody Inches N [mm] FLG F750H/HU 2" [41.9] [266] 3.62 [92] [481] F05 F765H/HU 2.5" [44.7] [266] 3.62 [92] [495] F05 F780H/HU 3" [45.2] [266] 3.62 [92] [501] F05 F7100HU 4" [52.1] [266] 3.62 [92] [520] F07 F7125HU 5" [54.4] [266] 3.62 [92] [533] F07 F7150HU 6" [55.6] [266] 3.62 [92] [547] F07 Note: Most F7 versions use 2 actuators. Meets culus or UL and S requirements without the need of an electrical ground connection. WRNING Live Electrical omponents! uring installation, testing, servicing and troubleshooting of this product, it may be necessary to work with live electrical components. Have a qualified licensed electrician or other individual who has been properly trained in handling live electrical components perform these tasks. Failure to follow all electrical safety precautions when exposed to live electrical components could result in death or serious injury. Line Volts 24 V Transformer a open a closed a lk (1) ommon Red (2) + Wht (3) + W The indication of direction is valid for switch position 1. GM24-3-X1 On/Off j y Floating Point Line Volts 24 V Transformer The indication of direction is valid for switch position lk (1) ommon Red (2) + Wht (3) GM24-3-X1 W559 91

92 GMX()24-MFT-T N4(H) NEM 4 ctuators, Multi-Function Technology imensions with 2-Way Valve ZM0825 Models GMX24-MFT-T-X1 N4 w/terminal block GM24-MFT-T-X1 N4H w/heater Technical ata ontrol 2 to 10 V, 4 to 20 m (default) variable (V, fl oating point, on/off) Power supply 24 V ± 20% 50/60 Hz 24 V ± 10% Power consumption running 8 W / heater 29W holding 2.5 W Transformer sizing 11 V (class 2 power source) / heater 26 V Electrical connection screw terminal (for 22 to 12 WG wire) Overload protection electronic throughout 0 to 95 rotation Input impedance 100 kω for 2 to 10 V (0.1 m) 500 Ω for 4 to 20 m 1000 Ω for fl oating point and on-off control ngle of rotation 95, adjustable with mechanical stop electronically variable irection of rotation reversible with Position indication visual pointer Manual override internal push button (UL Type 4) Running time 150 seconds (default) variable (75 to 290 seconds) Humidity 5 to 100% RH (UL Type 4) mbient temperature -22 F to 122 F [-30 to 50 ] Storage temperature -40 F to 176 F [-40 to 80 ] Housing type UL Type 4/NEM 4/IP66 Housing material Polycarbonate gency listings culus according to UL , UL and N/S E ; ertifi ed to IE/EN and IE/EN EM E according to 2004/108/E Quality standard ISO 9001 Valve Nominal imensions (Inches [mm]) Size Valve ody Inches N [mm] F SHP 2" [44.5] 3.62 [92] [266] [440] F SHP 2.5" [47.8] 3.62 [92] [266] [440] F SHP 3" [48.8] 3.62 [92] [266] [459] F SHP 4" [54.1] 3.62 [92] [266] [478] F SHP 2" [44.5] 3.62 [92] [266] [440] F SHP 2.5" [47.8] 3.62 [92] [266] [440] F SHP 3" [48.8] 3.62 [92] [266] [459] F SHP 4" [54.1] 3.62 [92] [266] [478] imensions with 3-Way Valve Valve Nominal imensions (Inches [mm]) Size Valve ody Inches N [mm] F SHP 2" [288] [266] [266] [440] F SHP 2.5" [290] [266] [266] [440] F SHP 3" [291] [266] [266] [459] F SHP 4" [294] [266] [266] [478] F SHP 2" [288] [266] [266] [440] F SHP 2.5" [290] [266] [266] [440] F SHP 3" [291] [266] [266] [459] F SHP 4" [294] [266] [266] [478] Note: Most F7 versions use dual actuators. ZM

93 GMX()24-MFT-T N4(H) NEM 4 ctuators, Multi-Function Technology imensions with 3-Way Valve ZM ontact closures & also can be triacs. & should both be closed for triac source and open for triac sink. For triac sink the common connection from the actuator must be connected to the hot connection of the controller. The ZG-R Ω resistor may be used. Valve ody Valve Nominal Size N IN [mm] imensions (Inches [mm]) FLG F750H/HU 2" [286] [266] [266] [481] F05 F765H/HU 2.5" [287] [266] [266] [495] F05 F780H/HU 3" [288] [266] [266] [501] F05 F7100HU 4" [294] [266] [266] [520] F07 F7125HU 5" [295] [266] [266] [533] F07 F7150HU 6" [297] [266] [266] [547] F07 Note: Most F7 versions use 2 actuators. WRNING Live Electrical omponents! uring installation, testing, servicing and troubleshooting of this product, it may be necessary to work with live electrical components. Have a qualified licensed electrician or other individual who has been properly trained in handling live electrical components perform these tasks. Failure to follow all electrical safety precautions when exposed to live electrical components could result in death or serious injury. W399_08 Wiring iagrams 1 Provide overload protection and disconnect as required. 2 UTION Equipment amage! ctuators may be connected in parallel if not mechanically mounted to the same shaft. Power consumption and input impedance must be observed. V/4-20 m W399_08 3 ctuators may also be powered by 24 V. Position feedback cannot be used with Triac sink controller. 4 The actuator internal common reference is not compatible. ontrol signal may be pulsed from either the Hot (source) 5 or the ommon (sink) 24 V line. Line Volts 3 ontrol Signal 2 to 10 V 24 V Transformer ( ) (+) Master lk (1) ommon Red (2) + Hot Wht (3) Y Input, 2 to 10 V Org (5) U Output 2 to 10 V W W Slave 5 5 Master_Slave PWM On/Off control W399_08 W399_08 lk (1) ommon Red (2) + Hot Wht (3) Y Input, 2 to 10 V Org (5) U W W Master/Slave US N Floating Point control LTIN MERI / RIEN 93

94 NSV-SY attery ack-up System For elimo SY Series Electric ctuators, 2 Position or Modulating pplication Typically, applications requiring fail-safe operation of actuated devices have had to rely on either the limited power of mechanical spring return actuators, or use costly high pressure pneumatic devices to provide fail-safe positioning. Model NSV series computer-grade UPS back-up systems designed for use with SY Series electric industrial quarter-turn actuators provides the power necessary to drive these actuators to a fi eld selectable fail-safe position. The system consists of a painted steel key lock hinged door controls cabinet which houses the logic switching, all fi eld wiring terminal points and a computer-grade back-up system. The back-up system is a component-level device which utilizes a replaceable spill-proof battery pack that can be readily purchased at most offi ce-supply centers. Provides Fail-Safe Operation for SY Series Industrial Electric ctuators, SY1 through SY12. Field Selectable Fail irection Readily vailable Sealed Lead-cid attery Packs Provides 500% of Power Requirements for Full Load ycle Safety in Numbers The system is designed to provide at a minimum up to 500% of the power required to drive the various actuators through their full 90 degree rotation at full running amperage draws. However, when the actuators have reached their fi eld-selectable end-of-travel positions, current draw drops to zero and the back-up system sits idle until either the time-out function integral to the battery is reached or the mains power returns, whichever occurs fi rst. Simple User Interface Key Lock Hinged Front Steel ontrols Enclosure Indicator lights visible through the viewport on the front and side of the control cabinet give status indication of mains power, back-up system charging and fail-safe operation. The NSV series is powered from building power and all power and logic interface wiring passes through the control cabinet. There are two different series produced, one is used for actuators which operate under 2 position or on/ off control schemes, while the second series is used for actuators operating under proportional control schemes. Various models are available within these two series to provide the most cost effective and effi cient means of providing fail-safe operation for these actuators. NOTE: Universal Power Supply must be removed from cabinet to access the battery. attery must be connected to the wire harness to activate the Universal Power Supply. NOTE: Universal Power Supply must be turned on to charge the battery. 94

95 NSV-SY attery ack-up System For elimo SY Series Electric ctuators, 2 Position or Modulating T1 MINS POWER G N GN L2 (NEUTRL) 120V.. LINE VOLTGE H L1 (HOT) ONTROL LOGI M3 8 M2 FIEL LOGI LOSE OPEN LINE SENSE SWITHING GRN G T 7 GREEN GROUNING SREW +t HETER (OPT.) NOTE: TERMINL #7 LSO POWERS OTHER ELETRONIS & MUST E WIRE WVEFORM GENERTOR 1 THERML OVERLO UTOMTI RESET M1 120V SY TUTOR M2 M M3 7 5 NO PITOR TUTOR RIVE 1 5 OPEN LOSE OM OM N NO N SWITH 1 SWITH 2 NO 6 OM N SWITH 3 NOTE: SWITHES SHOWN WITH TUTOR FULLY OPEN F NO OM SWITH 4 N E K-UP SYSTEM INET Sequence of Operation - 2 Position ontrol FIEL WIRING TUTOR WIRING The back up system is wired in series between the mains power and the actuator. Under normal operation, power supplied to T1 H & N terminals will illuminate the green LINE IN indicator light and provide charging voltage to the battery system. While under mains power, the fi eld select switch (or form contacts) are enabled to control the positioning of the actuator. The end user can install a center-off switch for 3 point fl oating control, a SPT toggle switch for 2 position control, or interface through an automation system s form contacts. ny method of operation will not affect the back up unit s operation. While under mains power, the blue T HRGING indicator light is illuminated while the yellow /U POWER indicator light remains off. While under mains power, the position of the FIL POSITION SELET switch is irrelevant. Power is supplied through the interface cabinet and the actuator heater is enabled. No current is being drawn from the battery system during this mode of operation. When the mains power is lost, charging power is no longer supplied to the battery system, and the green LINE IN indicator light is turned off. The battery system automatically generates modifi ed-sine wave line voltage to provide power for the actuator. The blue T HRGING indicator light is turned off, and the yellow /U POWER indicator light is turned on. The FIL POSITION SELET switch becomes active, and depending on its position, drives the actuator either fully open or fully closed. uring this mode of operation, the heater is NOT energized, and the position of any fi eld interface switching is irrelevant. The battery system will provide ample power to drive the actuator more than 5 full torque cycles. However, once the actuator reaches its end-of-travel limit switch, power drain from the back-up system is reduced to the requirements of the yellow /U POWER indicator light. fter 15 minutes, the battery system turns itself off and waits for the mains power to return. The gear train design of the SY actuator provides automatic locking of the actuator position after the battery system shuts down. Normal operation is resumed when mains power returns. 95

96 NSV-SY attery ack-up System For elimo SY Series Electric ctuators, 2 Position or Modulating Sequence of Operation - Modulating ontrol Note: This Model requires modifi cation to SY-MFT Model interface wiring inside the SY actuator. The back up system is wired in series between the mains power and the actuator. Under normal operation, power supplied to T1 H & N terminals will illuminate the green LINE IN indicator light and provide charging voltage to the battery system. While mains power is present, the SY drive logic interface card is enabled and provides proportional positioning of the SY actuator in response to incoming signals from customer supplied fi eld automation devices. While under mains power, the blue T HRGING indicator light is illuminated while the yellow /U POWER indicator light remains off. While under mains power, the position of the FIL POSITION SELET switch is irrelevant. Power is supplied through the interface cabinet and the actuator heater is enabled. ll internal actuator controls are otherwise not affected by the backup system. ll movement of the actuator is controlled by the automation control system. No current is being drawn from the battery system during this mode of operation. When the mains power is lost, charging power is no longer supplied to the battery system, and the green LINE IN indicator light is turned off. The battery system automatically generates modifi ed-sine wave line voltage to provide power for the actuator. The blue T HRGING indicator light is turned off, and the yellow /U POWER indicator light is turned on. The FIL POSITION SELET switch becomes active, and depending on its position, drives the actuator either fully open or fully closed. uring this mode of operation the incoming proportional signal is irrelevant. The battery system will provide ample power to drive the actuator more than 5 full torque cycles. However, once the actuator reaches its end-of-travel limit switch, power drain from the back-up system is reduced to the requirements of the yellow /U POWER indicator light. fter 15 minutes, the battery system turns itself off and waits for the mains power to return. The gear train design of the SY actuator provides automatic locking of the actuator position after the battery system shuts down. Normal operation is resumed when mains power returns. 96

97 NSV-SY attery ack-up System For elimo SY Series Electric ctuators, 2 Position or Modulating Key ccess and Status Viewports attery System Status Indicators ll onnections to P ackup are Modular onnection to P Interface SIZING N PERFORMNE HRT ctuator Model Torque Output Runtime (secs) raw (amps) 2 Position Model Modulating Model Runtime at 50% apacity (minutes) % apacity Used at Full Runtime Replacement attery SY1-110(P) NSV-SY-01 NSV-SY % R2 SY2-110(MFT) NSV-SY-01 NSV-SY % R2 SY3-110(MFT) NSV-SY-01 NSV-SY % R2 SY4-110(MFT) NSV-SY-01 NSV-SY % R2 SY5-110(MFT) NSV-SY-01 NSV-SY % R2 SY6-110(MFT) NSV-SY-01 NSV-SY % R2 SY7-110(MFT) NSV-SY-03 NSV-SY % R2 SY8-110(MFT) NSV-SY-05 NSV-SY % R32 SY9-110(MFT) NSV-SY-05 NSV-SY % R32 SY10-110(MFT) NSV-SY-05 NSV-SY % R32 SY11-110(MFT) NSV-SY-05 NSV-SY % R32 SY12-110(MFT) NSV-SY-05 NSV-SY % R32 SY1-24(P) NSV-SY-11 NSV-SY % R2 SY2-24(MFT) NSV-SY-11 NSV-SY % R2 SY3-24(MFT) NSV-SY-11 NSV-SY % R2 SY4-24(MFT) NSV-SY-11 NSV-SY % R2 SY5-24(MFT) NSV-SY-11 NSV-SY % R2 SY1-220(P) NSV-SY-21 NSV-SY % R2 SY2-220(MFT) NSV-SY-21 NSV-SY % R2 SY3-220(MFT) NSV-SY-21 NSV-SY % R2 SY4-220(MFT) NSV-SY-21 NSV-SY % R2 SY5-220(MFT) NSV-SY-21 NSV-SY % R2 SY6-220(MFT) NSV-SY-21 NSV-SY % R2 SY7-220(MFT) NSV-SY-23 NSV-SY % R32 SY8-220(MFT) NSV-SY-23 NSV-SY % R32 SY9-220(MFT) NSV-SY-23 NSV-SY % R32 SY10-220(MFT) NSV-SY-25 NSV-SY % R32 SY11-220(MFT) NSV-SY-25 NSV-SY % R32 SY12-220(MFT) NSV-SY-25 NSV-SY % R32 97

98 NSV-SY attery ack-up System Wiring iagrams UTOMTION SYSTEM OR SWITH M3 LOSE M2 OPEN 8 H 110V ~ N G LOSE OPEN 1 TUTOR #1 G G UX SW TERMINLS E F Open = to 3 Opened = to NSV-SY-01 NSV-SY-03 NSV-SY-05 FIEL WIRING lose = Hot = to 4 losed = to F to V MX SY(1-12)-110 Wiring diagram for a single on/off SY series 110 V actuator. uilding mains power is connected to G, N & H terminals. control switch or dry contacts are connected between terminal 8 and M2 or M3 to control the positioning of the actuator under power. Terminals G, 1, 5, 6 & 7 are connected to the SY actuator as shown. Observe wire size rules for longer wire runs. 98

99 NSV-SY attery ack-up System Wiring iagrams UTOMTION SYSTEM OR SWITH M3 LOSE M2 OPEN 8 H K1-110V ~ TUTOR #1 UX SW TERMINLS N G E F Open = to 3 Opened = to G lose = to 4 losed = to F Hot = to V MX 7 6 LOSE 5 OPEN K1 K1-1 G NSV-SY-01 Max Load 150V NSV-SY-03 Max Load 300V NSV-SY-05 Max Load 500V FIEL WIRING NOTES: K1 OIL MUST MTH SUPPLY VOLTGE. IN THIS SENRIO, TUTOR #1 WORKS OPPOSITE TUTOR #2. IN THIS EXMPLE, K1 IS 4PT RELY. NOTE: o NOT exceed total V capacity of NSV-SY backup system. Wiring diagram for multiple on/off SY series 110 V actuators. G Open = lose = Hot = to to to TUTOR #2 UX SW TERMINLS Opened = losed = SY(1-12)-110 OSERVE POLRITY OF ONTROL SIGNLS N POWER E 5 250V MX o NOT exceed the Max Loads as stated above when connecting multiple actuators. ctuators connected in this manner operate in parallel from the common automation control switch and will fail-safe position together. uilding mains power is connected to G, N & H terminals. control switch or dry contacts are connected between terminal 8 and M2 or M3 to control the positioning of the actuator under power. Terminals G, 1, 5, 6 & 7 are connected to the SY actuator as shown. Observe wire size rules for longer wire runs. F to to F 99

100 NSV-SY attery ack-up System Wiring iagrams Wiring diagram for a single proportional SY series 110 V actuator. uilding mains power is connected to G, N & H terminals. The control signal from the automation system is wired directly to the SY actuator. Terminals G, 2, 5, 6, M2 & M3 are connected to the SY actuator as shown. Observe wire size rules for longer wire runs. 100

101 NSV-SY attery ack-up System Wiring iagrams R K WH S Y 1 U ~/+ / s outlined below X / X R R K K R Mains Power 120V..Line Voltage G N H GN L2 (neutral) L1 (hot) 5 2 K1 K2 6 M2 M3 G NSV-SY-12 Max. Load: 150V K1- K1- K2- K2- nalog Signal Input Output (+) (-) (+) (-) IN OUT Wiring diagram for multiple proportional SY series 110 V actuators. X X R R K WH Y 1 U ~/+ / o NOT exceed the Max Loads as stated above when connecting multiple actuators. ctuators connected in this manner operate in parallel from the common automation control signal and will fail-safe position together. uilding mains power is connected to G, N & H terminals. The control signal from the automation system is wired directly to the SY actuator. Terminals G, 2, 5, 6, M2 & M3 are connected to the SY actuators as shown. Observe wire size rules for longer wire runs. K1 and K2 must be supplied. / R K K R S

102 NSV-SY attery ack-up System Wiring iagrams UTOMTION SYSTEM OR SWITH M3 LOSE M2 OPEN 8 H 110V ~ N G LOSE OPEN 1 TUTOR #1 G G UX SW TERMINLS E F NSV-SY-11 FIEL WIRING Open = lose = Hot = to to to Opened = to losed = to F 5 250V MX SY(1-5)-24 OSERVE POLRITY OF ONTROL SIGNLS N POWER Wiring diagram for a single on/off SY series 24 V actuator. uilding mains power is connected to G, N & H terminals. control switch or dry contacts are connected between terminal 8 and M2 or M3 to control the positioning of the actuator under power. Terminals G, 1, 5, 6 & 7 are connected to the SY actuator as shown. Observe wire size rules for longer wire runs. The 24vac transformer required to run the SYxxx-24 actuator is built in to the NSV cabinet. 102

103 NSV-SY attery ack-up System Wiring iagrams UTOMTION SYSTEM OR SWITH M3 LOSE M2 OPEN 8 H K1-110V ~ TUTOR #1 UX SW TERMINLS N G E F Open = to 3 Opened = to G lose = to 4 losed = to F Hot = to V MX 7 6 LOSE 5 OPEN K1 K1-1 G G TUTOR #2 UX SW TERMINLS E F NSV-SY-11 Max Load 150V FIEL WIRING NOTES: K1 OIL MUST MTH SUPPLY VOLTGE. IN THIS SENRIO, TUTOR #1 WORKS OPPOSITE TUTOR #2. IN THIS EXMPLE, K1 IS 4PT RELY. Open = to 3 Opened = to lose = to 4 losed = to F Hot = to V MX SY(1-5)-24 OSERVE POLRITY OF ONTROL SIGNLS N POWER NOTE: o NOT exceed total V capacity of NSV-SY backup system. Wiring diagram for multiple on/off SY series 24 V actuators. o NOT exceed the Max Loads as stated above when connecting multiple actuators. ctuators connected in this manner operate in parallel from the common automation control switch and will fail-safe position together. uilding mains power is connected to G, N & H terminals. control switch or dry contacts are connected between terminal 8 and M2 or M3 to control the positioning of the actuator under power. Terminals G, 1, 5, 6 & 7 are connected to the SY actuator as shown. Observe wire size rules for longer wire runs. The 24vac transformer required to run the SYxxx-24 actuator is built in to the NSV cabinet. 103

104 NSV-SY attery ack-up System Wiring iagrams G N GN Mains Power 120V..Line Voltage L2 neutral H L1 hot M2 S M3 Y 1 U ~/+ /- R K WH G X X K R NSV-SY-12 nalog Signal (+) IN Input (-) ISONNET THE WIRE FROM TERMINL 3 N, ONNET TO TERMINL 6 ON THE NSV. / R R K output (+) (-) OUT Wiring diagram for a single proportional SY series 24 V actuator. uilding mains power is connected to G, N & H terminals. The control signal from the automation system is wired directly to the SY actuator. Terminals G, 2, 5, 6, M2 & M3 are connected to the SY actuator as shown. Observe wire size rules for longer wire runs. The 24vac transformer required to run the SYxxx-24 actuator is built in to the NSV cabinet. 104

105 NSV-SY attery ack-up System Wiring iagrams R K WH S Y 1 U ~/+ / s outlined below X ISONNET THE WIRE FROM TERMINL 3 N, ONNET TO TERMINL 6 ON THE NSV. / X R R K K R Mains Power 24V..Line Voltage G N H GN L2 (neutral) L1 (hot) 2 5 K1 K2 6 M2 M3 G NSV-SY-12 Max. Load: 150V K1- K1- K2- K2- nalog Signal Input Output (+) (-) (+) (-) IN OUT R R K WH Y 1 U ~/+ / X ISONNET THE WIRE FROM TERMINL 3 N, ONNET TO TERMINL 6 ON THE NSV. Wiring diagram for multiple proportional SY series 24 V actuators. o NOT exceed the Max Loads as stated above when connecting multiple actuators. ctuators connected in this manner operate in parallel from the common automation control signal and will fail-safe position together. uilding mains power is connected to G, N & H terminals. The control signal from the automation system is wired directly to the SY actuator. Terminals G, 2, 5, 6, M2 & M3 are connected to the SY actuators as shown. Observe wire size rules for longer wire runs. The 24vac transformer required to run the SYxxx-24 actuator is built in to the NSV cabinet. K1 and K2 must be supplied. / X R K K R S

106 NSV-SY attery ack-up System Wiring iagrams UTOMTION SYSTEM OR SWITH M3 LOSE M2 OPEN 8 L1 220V ~ L2 G LOSE OPEN 1 TUTOR #1 G G UX SW TERMINLS E F Open = to 3 Opened = to NSV-SY-21 NSV-SY-23 NSV-SY-25 FIEL WIRING lose = Hot = to 4 losed = to F to V MX SY(1-12)-220 Wiring diagram for a single on/off SY series 220 V actuator. uilding mains power is connected to G, N & H terminals. control switch or dry contacts are connected between terminal 8 and M2 or M3 to control the positioning of the actuator under power. Terminals G, 1, 5, 6 & 7 are connected to the SY actuator as shown. Observe wire size rules for longer wire runs. 106

107 NSV-SY attery ack-up System Wiring iagrams UTOMTION SYSTEM OR SWITH M3 LOSE M2 OPEN 8 L1 K1-220V ~ TUTOR #1 UX SW TERMINLS L2 G E F Open = to 3 G 4 F Hot = to V MX 7 6 LOSE 5 OPEN K1 K1-1 G NSV-SY-21 Max Load 150V NSV-SY-23 Max Load 300V NSV-SY-25 Max Load 500V FIEL WIRING NOTES: K1 OIL MUST MTH SUPPLY VOLTGE. IN THIS SENRIO, TUTOR #1 WORKS OPPOSITE TUTOR #2. IN THIS EXMPLE, K1 IS 4PT RELY. NOTE: o NOT exceed total V capacity of NSV-SY backup system. Wiring diagram for multiple on/off SY series 220 V actuators. G Open = Hot = to to TUTOR #2 UX SW TERMINLS SY(1-6)-220 OSERVE POLRITY OF ONTROL SIGNLS N POWER E 5 250V MX o NOT exceed the Max Loads as stated above when connecting multiple actuators. ctuators connected in this manner operate in parallel from the common automation control switch and will fail-safe position together. uilding mains power is connected to G, N & H terminals. control switch or dry contacts are connected between terminal 8 and M2 or M3 to control the positioning of the actuator under power. Terminals G, 1, 5, 6 & 7 are connected to the SY actuator as shown. Observe wire size rules for longer wire runs. F F 107

108 Wiring iagrams Wiring diagram for a single proportional SY series 220 V actuator. uilding mains power is connected to G, N & H terminals. The control signal from the automation system is wired directly to the SY actuator. Terminals G, 2, 5, 6, M2 & M3 are connected to the SY actuator as shown. Observe wire size rules for longer wire runs. 108

109 NSV-SY attery ack-up System Wiring iagrams R K WH S Y 1 U ~/+ / s outlined below X / X R R K K R Mains Power 220V..Line Voltage G N H GN L2 (neutral) L1 (hot) 5 2 K1 K2 6 M2 M3 G NSV-SY-12 Max. Load: 150V K1- K1- K2- K2- nalog Signal Input Output (+) (-) (+) (-) IN OUT Wiring diagram for multiple proportional SY series 220 V actuators. X X R R K WH Y 1 U ~/+ / o NOT exceed the Max Loads as stated above when connecting multiple actuators. ctuators connected in this manner operate in parallel from the common automation control signal and will fail-safe position together. uilding mains power is connected to G, N & H terminals. The control signal from the automation system is wired directly to the SY actuator. Terminals G, 2, 5, 6, M2 & M3 are connected to the SY actuators as shown. Observe wire size rules for longer wire runs. K1 and K2 must be supplied. / R K K R S

110 attery ack-up System For elimo SY Series Electric ctuators, 2 Position or Modulating K-UPS S 350V/PRT NUMER: K350 vailability: North merica, Latin merica Product Overview escription P ack-ups, 350V/210W, Input 120V/ Output 120V General Features ddl Surge Protected Outlets, udible larms, ord Management, Intelligent attery Management, Internet FX - modem - SL protection, Overload Indicator, Replace att Indicator, Site wiring fault indicator, Software, User Replaceable batteries ocumentation User Manual K-UPS S 500V/PRT NUMER: K500 vailability: North merica, Latin merica Product Overview escription P ack-ups, 500V/300W, Input 120V/ Output 120V General Features ddl Surge Protected Outlets, udible larms, ord Management, Intelligent attery Management, Internet FX - modem - SL protection, Overload Indicator, Replace att Indicator, Site wiring fault indicator, Software, User Replaceable batteries ocumentation User Manual Technical Specifi cations Input Nominal input 120 V Input frequency 50/60 Hz +/- 5 Hz (auto sensing) Input onnection Type NEM 5-15P ord Length 6 feet Input voltage range for main operations V Output Output power capacity 350 V Output power capacity 210 Watts Nominal output voltage 120 V Waveform type Stepped approximation to a sinewave Output onnections (3) NEM 5-15R (3) NEM 5-15R (Surge) atteries Typical backup time at half load 11.4 minutes attery type Maintenance-free sealed Lead-cid battery with suspended electrolyte: leakproof Typical recharge time ** 8 hour(s) Replacement battery cartridge (1) R2 ommunications & Management ontrol panel LE status display with On Line: On attery: Replace attery and Overload indicators udible alarm larm when on battery: distinctive low battery alarm : overload continuous tone alarm Surge Protection and Filtering Surge energy rating 480 joules Filtering Full time multi-pole noise fi ltering: 5% IEEE surge letthrough: zero clamping response time: meets UL 1449 ataline protection RJ-11 Modem/Fax/SL protection (two wire single line) Technical Specifi cations Input Nominal input 120 V Input frequency 50/60 Hz +/- 5 Hz (auto sensing) Input onnection Type NEM 5-15P ord Length 6 feet Input voltage range for main operations V Output Output power capacity 500 V Output power capacity 300 Watts Nominal output voltage 120 V Waveform type Stepped approximation to a sinewave Output onnections (3) NEM 5-15R (3) NEM 5-15R (Surge) atteries Typical backup time at half load 11.4 minutes attery type Maintenance-free sealed Lead-cid battery with suspended electrolyte: leakproof Typical recharge time ** 8 hour(s) Replacement battery cartridge (1) R2 ommunications & Management ontrol panel LE status display with On Line: On attery: Replace attery and Overload indicators udible alarm larm when on battery: distinctive low battery alarm: overload continuous tone alarm Surge Protection and Filtering Surge energy rating 480 joules Filtering Full time multi-pole noise fi ltering: 5% IEEE surge letthrough: zero clamping response time: meets UL 1449 ataline protection RJ-11 Modem/Fax/SL protection (two wire single line) 110

111 attery ack-up System For Powered elimo SY Series Electric ctuators, 2 Position or Modulating K-UPS 900V/PRT NUMER: R900 vailability: North merica, Latin merica Product Overview escription P ack-ups, 900V/540W, Input 120V/ Output 120V General Features udible larms, utomatic Voltage Regulation (VR), Easy Overload Recovery, Ethernet Protection, Hot Swap atteries, Modem Protection, Overload Indicator, Replace att Indicator, Site wiring fault indicator, User Replaceable batteries ocumentation User Manual PHYSIL IMENSIONS NSV-SY Series ack-up Systems Maximum imensions NSV NSV-SY NSV-SY 01, 02 21, 22 03, 04, 11 12, 23, 24 05, 06 25, 26 Height Width epth Net weight 36# 42# 44# Technical Specifi cations Input Nominal input voltage 120 V Input frequency 50/60 Hz +/- 3 Hz (auto sensing) Input onnection Type NEM 5-15P ord Length 6 feet Input voltage range for main operations V Output Output power capacity 900 V Output power capacity 540 Watts Nominal output voltage 120 V Waveform type Stepped approximation to a sinewave Shipping Weight 38# 44# 48# Environmental Operating Relative Humidity 0-95% Operating Elevation feet ( m) Storage Temperature (5-113 F) Storage Relative Humidity 0-95% Storage Elevation feet ( m) udible noise at 1 meter from surface of unit 45 d Online thermal dissipation 24 TU/hr Output onnections (7)NEM 5-15R atteries Typical backup time at half load 17.6 minutes attery type Maintenance-free sealed Lead-cid battery with suspended electrolyte: leakproof Typical recharge time ** 8 hour(s) Replacement battery cartridge (1) R32 ommunications & Management ontrol panel LE status display with On Line: On attery: Replace attery and Overload indicators udible alarm larm when on battery: distinctive low battery alarm: overload continuous tone alarm Surge Protection and Filtering Surge energy rating 320 joules Filtering Full time multi-pole noise fi ltering: 5% IEEE surge letthrough: zero clamping response time: meets UL 1449 ataline protection RJ-11 Modem/Fax/SL protection (two wire single line) plus RJ-45 ethernet onformance - P ack UP Module pprovals S, F, UL 1778 pprovals F Part 15 lass, Industry anada, UL 1778, cul Listed ** The time to recharge to 90% of full battery capacity following a discharge to shutdown using a load rated for 1/2 the full load rating of the UPS. 111

112 Installation Recommendations F6 H(U), F7 H(U) Series utterfly Valves H(U) Series utterfly Valves Storage of utterfly Valve ssemblies ssemblies must be stored indoors, protected from the elements. Materials received on job sites that have long installation lead times should receive extra protection from construction damage. Resilient seats must be protected from abrasion, cutting and nicking, as this will damage the liner and may cause flange area leaks. Electric actuators cannot be stored in wet, damp or caustic areas. o not store construction material on top of valve assemblies. Installation Practices H(U) series butterfly valves are designed to be installed between NSI 125/150 flat-faced, raised face, slip-on or weld neck flanges. Valve should be installed a minimum of 10 pipe diameters from upstream or downstream elbows, strainers, pumps, etc. For chilled water, condenser water or hot water applications, the valve should be installed with the stem in a vertical orientation, with the actuator mounted above the valve. For applications in which there is a possibility of sediment in the flow, the valve should be installed with the stem in a horizontal position and the bottom of the disc should close FROM the downstream side, rather than from the upstream side. Make sure the flange faces are clean and free of rust, scale and debris to prevent damage to the liner face. o NOT use flange gaskets on H(U) series F valves. (Fig. 1a) Follow the recommended flange bolting sequence. (Fig. 8, pg. 85) When installing in Victaulic piping systems, use Victaulic 41 series flange nipples. Installation using Welded Flanges Mount flanges on both sides of valve body and install bolts to properly align valve body and both flanges. Install the valve with the disc in the lmost losed position (Fig. 1) o not use any flange gaskets (Fig. 1a) Make sure the valve liner and flange internal diameters are in alignment. (Fig. 2) Take valve body / flange pair assembly and align with piping ends. TK weld the flanges to the piping in several places. (Fig. 3a) o NOT seam weld at this time! Remove the lug bolts and carefully remove the valve body from the flanges. Seam weld the entire flange / piping connection for both flanges. (Fig 3b) Let the piping components cool completely before re-inserting the valve body. (Fig. 4) WRNING! Seam welding with the valve body installed between the flanges can damage the liner due to heat migration through the flange to the valve body. Max Torque for olts Valve Size olt Size Max Torque [ft-lbs] 2-4 5/ / / / / / /

113 Installation Recommendations F6 H(U), F7 H(U) Series utterfly Valves H(U) Series utterfly Valves 1Fig. 1 1Fig. 3a Fig. 1 3b Fig. 1a 1Fig. 4 1Fig. 2 >

114 Installation Recommendations F6 H(U), F7 H(U) Series utterfly Valves FLNGE OLTING REOMMENTIONS Flange etail for NSI 16.5 Pipe Flanges FLNGES RILLING OLTING Nominal iameter of iameter of Number olt ircle olt Holes of olts Pipe Size Flange iameter Flange Thickness iameter of olts 2 6 3/4 4-3/4 3/4 4 5/8 2-1/2 7 7/8 5-1/2 3/4 4 5/ /2 15/16 6 3/4 4 5/ /16 7-1/2 3/4 8 5/ /16 8-1/2 7/8 8 3/ /2 7/8 8 3/ /2 1-1/8 11-3/4 7/8 8 3/ / / / / / /8 18-3/4 1-1/ /2 1-7/ /4 1-1/ /8 22-3/4 1-1/ / /2 1-11/ / / /8 29-1/2 1-3/ /4 PRE-INSTLLTION PROEURE 1. Remove any protective fl ange covers from the valve. 2. Inspect the valve to be certain the waterway is free from dirt and foreign matter. e certain the adjoining pipeline is free from any foreign material such as rust and pipe scale or welding slag that could damage the seat and disc sealing surfaces. 3. ny actuator should be mounted on the valve prior to installation to facilitate proper alignment of the disc in the valve seat. 4. heck the valve identifi cation tag for materials, and operating pressure to be sure they are correct for the application. WRNING! Personal injury or property damage may result if the valve is installed where service conditions could exceed the valve ratings. 5. heck the flange bolts or studs for proper size, threading, and length. 6. These valves are designed to be installed between SME/NSI lass 125/150 fl anges. 7. arefully follow installation using welded fl anges on page 82 of this document. 8. Follow SME fl ange alignment standards: SETION LIGNMENT a. PIPING ISTORTIONS: ny distortion of piping to bring into alignment for joint assembly which introduces a detrimental strain in equipment or piping components is prohibited. b. FLNGE JOINTS: efore bolting up, flange faces shall be aligned to the design plane within 1/16 /ft measured across any diameter; flange bolt holes shall be aligned within 1/8 maximum offset. 9. When observed during assembly, the fl ange faces shall be parallel within 1 degree, and the force required to align pipe axes shall not exceed 10 lb/ft per inch of NF bolts and nuts shall be fully engaged. FLNGE OLTING REOMMENTIONS Lug Valves, 2-30, NSI 125/150 olt Pattern Valve Size Thread Size Number Required olt Length Semi-Lug utterfl y (inches) 2 5/ /2 5/ / / / / / / / / / / /

115 0 Installation Recommendations F6...H(U), F7...H(U) Series utterfly Valves Valve Installation Procedure Position the connecting pipe fl anges in the line to insure proper alignment prior to valve installation. Spread the pipe fl anges apart enough to allow the valve body to be located between the fl anges without actually contacting the fl ange surfaces. Exercise particular care in handling the valve so as to prevent possible damage to the disc or seat faces. Note: ctuator must be mounted at or above pipe center line for all actuator types. (Fig. 6) Fig For Lug style valves: a. Place the valve between the fl anges. b. Install all bolts between the valve and the mating fl anges. Hand tighten bolts as necessary. (Fig. 7) 2. efore completing the tightening of any bolts, the valve should be centered between the fl anges and then carefully opened and closed to insure free, unobstructed disc movement. 3. Using the sequence, (Fig. 8) tighten the fl ange bolts evenly to assure uniform compression. In assembling fl ange joints, the resilient seating surface shall be uniformly compressed. (Fig. 5) 4. If an actuator is to be operated, electricity should be connected to the unit in accordance with the local electrical codes. 5. ycle the valve to the fully open position, then back to the fully closed position, checking the actuator travel stop settings for proper disc alignment. The valve should be operated to assure that no binding is taking place. If no power is available, use the manual handwheel. 6. The valve is now ready for operation. 1Fig. 7 Fig. 5 0 >0 >0 1Fig

116 Installation Recommendations 1Fig. 9 VI Series utterfly Valves Installation onsult the Victaulic I-100 field instructional handbook for product installation of the VI series butterfly valves. F6 H(U), F7 H(U) Series utterfly Valves Valve Installation- ead End Service 1. Follow previously described pre-installation and installation procedures. 2. To achieve the full close-off pressure of the H/HU series, a flange is required on the open or down stream side of the valve (Fig. 9) Maintenance Instructions Safety Precautions efore removing the valve from the line or loosening any bolts, it is important to verify the following conditions: 1. e sure the line is depressurized and drained. 2. e sure of the pipeline media. Proper care should be taken for protection against toxic and/or flammable fluids. 3. Never remove the valve without an Operator (Manual or utomatic) already attached to the valve shaft. 4. Never remove the Operator from the valve while the valve is in the pipeline under pressure. 5. lways be sure that the disc is cracked approximately 5 off of the closed position before removing the valve. General Maintenance The following periodic preventative maintenance practices are recommended for all utterfly Valves. 1. Operate the valve from full open to full closed to assure operability. 2. heck flange bolting, actuator mounts and hangers for evidence of loosening and correct as needed. 3. Inspect the valve and surrounding area for previous or existing leakage at flange faces or shaft connections. 4. heck piping and/or wiring to actuators and related equipment for looseness and correct as needed. 5. If not in use, exercise the butterfly valve (full open and close) at least once a month. 116

117 Installation Recommendations SHP Series utterfly Valves Valve esign 1. The SHP Series High Performance utterfly Valve features a double offset (or, double eccentric) shaft design to minimize seat abrasion and lower torque. This double offset design allows the disc to lift off and cam away from the seat as it rotates open. 2. The SHP valve always rotates clockwise to close (when viewed from above) and counterclockwise to open. 3. The valve body has an Overtravel Stop which prevents the disc from over rotating into the wrong quadrant. This stop is not to be used as a disc position stop; if the disc contacts the Overtravel Stop, this means it has rotated beyond the seat. 4. The SHP valve is bidirectional, but the preferred installation position is with the seat in the upstream position (SUS). Note the arrow on the metal tag attached to the valve body. Safety Precautions 1. e sure the line is depressurized and drained. 2. e sure of the pipeline media. Proper care should be taken for protection against toxic and/or flammable fluids. 3. Never install the valve without an Operator (Manual or utomatic) already attached to the valve shaft. 4. Never remove the Operator from the valve while the valve is in the pipeline under pressure. 5. lways be sure that the disc is in the full-closed position before installing the valve. 6. Take care in handling the valve; if you treat it like a machine, it will operate like a machine if you treat it like a piece of pipe, it may work like a piece of pipe. Pipe Schedule ompatibility The SHP valve is designed to allow the disc edge to rotate into the open position without interference with the pipeline I.. in the following pipe schedules: SIZE NSI 150 NSI SH 80 SH SH 40 SH SH 30 SH ST WT 48 XS Product Identification 1. Every SHP valve has a metal identification tag attached to the valve body. Information includes the Figure Number, the Size and Pressure lass, the Materials of onstruction, and the Operating Pressures and Temperatures. 2. Every SHP valve is hydrostatically tested before it is shipped. The metal tag also includes a Serial Number; this number, unique for each valve, is recorded by the elimo Quality ontrol epartment along with the test results and material certification data, for individual traceability and verification of every valve produced. SHP series valves have a preferred flow direction. PreferredFlowrate Flange ompatibility The SHP valve is designed to fit between flanges as follows: NSI lass to 24 MSS SP-44 lass to 48 NSI lass 150 Flanges NSI lass to 24 MSS SP-44 lass NSI lass 200 Flanges Gasket ompatibility The SHP valve is designed to accommodate the use of standard fiber gaskets (such as non-asbestos, flexible graphite, asbestos or equivalent gasket materials) of 1/16 or less, meeting the dimensional requirements of NSI Thick elastomeric gaskets are not recommended. Metallic wound (Flexitallic) gaskets may also be used. UNPKING N STORGE INSTRUTIONS 1. heck the packing list against the valve received to verify that the quantities, sizes and materials are correct. 2. heck to make sure that the valve and operator were not damaged during shipment. 3. If the valve is to be stored before being installed, it should be protected from harsh environmental conditions. 4. Store the valve with the disc in the closed position to protect the sealing edge and the seat. 5. Keep the valve in a clean location, away from dirt, debris and corrosive materials. 6. Keep the valve in a dry area with the flange protectors attached. 7. Keep the valve in a cool location if possible, out of direct sunlight. 8. If not in use, exercise the butterfly valve (full open and close) at least once a month. 117

118 Installation Recommendations SHP Series utterfly Valves SHP Series utterfly Valves Storage of utterfly Valve ssemblies ssemblies must be stored indoors, protected from the elements. Materials received on job sites that have long installation lead times should receive extra protection from construction damage. Valve faces must be protected from abrasion, cutting and nicking, as this will damage the face and may cause flange area leaks. Electric actuators cannot be stored in wet, damp or caustic areas. o not store construction material on top of valve assemblies. Installation Practices SHP series butterfly valves are designed to be installed between NSI 125/150 flat-faced or raised face, slip-on weld neck flanges. Valve should be installed a minimum of 6 pipe diameters from upstream or downstream elbows, strainers, pumps, etc. For chilled water, condenser water or hot water applications, the valve should be installed with the stem in a vertical orientation, with the actuator mounted above the valve. For applications in which there is a possibility of sediment in the flow, the valve should be installed with the stem in a horizontal position and the bottom of the disc should close FROM the downstream side, rather than from the upstream side. Flange gaskets must be used on SHP series F valves. Make sure the flange faces are clean and free of rust, scale and debris to prevent damage to the flange gasket. Follow the recommended flange bolting sequence found in the Installation Recommendations section of this guide. Installation using Welded Flanges Mount flanges on both sides of valve body and install bolts to properly align valve body and both flanges. Make sure the valve I.. and flange internal diameters are in alignment. Take valve body / flange pair assembly and align with piping ends. TK weld the flanges to the piping in several places. o NOT seam weld at this time! Remove the lug bolts and carefully remove the valve body from the flanges. Seam weld the entire flange / piping connection for both flanges. Let the piping components cool completely before re-inserting the valve body. WRNING! Seam welding with the valve body installed between the flanges can damage the valve seats due to heat migration through the flange to the valve body. utterfl y Sizing and Selection ONSULT HRT ON PGE 21 (Flow in Standard Weight Pipe-Fluid Velocity in GPM). For SHP Series utterfly Valves, the 32 ft/second column is applied. For example: pplication requires a 2-way, 600 GPM utterfly valve, a valve of 3 minimum would be selected. The 3 valve at 32 ft/second would be able to withstand a capacity of 705 GPM, without damage to the seat. Notes 1. Most utterflies are line size and piping geometry is not considered. If valve size must be reduced, a recommendation is to select a valve only one size less than the pipe. (o not exceed velocity limit) 2. For a modulating utterfly valve, the v rating is determined at 60 open. For a 2-position utterfly valve, the v is determined at 90 open. onsult elimo Technical Support for applications involving steam, high velocity requirements, etc. 118

119 Installation Recommendations SHP Series utterfly Valves Pre-Installation Procedure 1. Remove the protective face covers from the valve. 2. Inspect the valve to be certain the waterway is free from dirt and foreign matter. e certain the adjoining pipeline is free from any foreign material such as rust and pipe scale or welding slag that could damage the seat and disc sealing surfaces. 3. ctuators should be mounted on the valve prior to installation to facilitate proper alignment of the disc in the valve seat. 4. The valve should be in the closed position. Make sure the open and closed positions of the actuator correspond to the counter-clockwise to open direction of rotation of the valve. 5. ycle the valve to the fully open position, then back to the fully closed position, checking the actuator travel stop settings for proper disc alignment. 6. heck the valve identifi cation tag for valve class, materials, and operating pressure to be sure they are correct for the application. WRNING! Personal injury or property damage may result if the valve is installed where service conditions could exceed the valve ratings. 7. heck the flange bolts or studs for proper size, threading, and length. REMEMER: Install the valve with the disc in the full-closed position using the appropriate flange gaskets on OTH valve flange faces. NOTE ctuator must be mounted at or above pipe center line for all actuator types Valve Installation Procedure The SHP High Performance utterfl y Valve can be installed in the pipeline with the shaft in the vertical, horizontal, or other intermediate position. ased on applications experience, however, in media with concentrations of solid or abrasive particles or media subject to solidifi cation buildup, valve performance and service life will be enhanced by mounting the valve with the shaft in the horizontal position. Fig. 8 ll SHP valves are bidirectional and can be mounted in the pipeline in either fl ow direction; however, the preferred fl ow direction for all seat styles and materials is with the seat retainer ring located upstream (sus) to provide maximum seat protection. For SHP Series valves a. Noting the fl ow direction arrow on the tag, place the valve between the fl anges, making sure the arrow on the tag points in the direction of the fl ow. b. Install the lower fl ange bolts loosely, leaving space for the fl ange gaskets. c. fter inserting the fl ange gaskets, install the remaining bolts. 3. Using the sequence shown to the right, tighten the fl ange bolts evenly to assure uniform gasket compression. UTION: The SHP valve should be centered between the fl anges and gaskets to prevent damage to the disc edge and shaft as a result of the disc striking the fl ange, gasket, or pipe. 4. Electricity should be connected to the unit as specifi ed by the actuator manufacturer. 5. The valve is now ready for operation

120 Installation Recommendations SHP Series utterfly Valves FLNGE OLTING REOMMENTIONS Lug Valves, 2 30, NSI 125/150 olt Pattern STUS & NUTS MHINE OLTS Valve Size Thread Size QTY LENGTH QTY LENGTH F QTY LENGTH G QTY LENGTH 2 5/ /2 5/ / / / / / / / / / /8-8 4** ** * ** / / /4-8 4** ** * ** 4.63 LUG OY HEX HE MHINE OLTS LUG OY STUS and NUTS olting and torque recommendations are made without warranty, and apply only to steel weld-neck or slip-on flanges. The use of lock washers and/or lubrication with the bolting will affect stated torque values. Length of machine bolts based on: 1. Gasket thickness of 0.06 inches. 2. Minimum flange thickness of weld-neck flanges per NSI 16.5 and Series. * Variation to specified bolting length may result in improper installation. FLNGE OLTING REOMMENTIONS Flange etail for NSI Pipe Flanges 150 SHP Series utterfly Valves FLNGES RILLING OLTING Nominal iameter of iameter of Number olt ircle olt Holes of olts Pipe Size Flange iameter Flange Thickness iameter of olts 2 6 3/4 4-3/4 3/4 4 5/8 2-1/2 7 7/8 5-1/2 3/4 4 5/ /2 15/16 6 3/4 4 5/ /16 7-1/2 3/4 8 5/ /16 8-1/2 7/8 8 3/ /2 7/8 8 3/ /2 1-1/8 11-3/4 7/8 8 3/ / / / / / /8 18-3/4 1-1/ /2 1-7/ /4 1-1/ /8 22-3/4 1-1/ / /2 1-11/ / / /8 29-1/2 1-3/ /4 Every effort is made to provide accurate information, but no liability for claims arising from erroneous data will be accepted by elimo. 120

121 Installation Recommendations SHP Series utterfly Valves FLNGE OLTING REOMMENTIONS Lug Valves, 2-24, NSI 250/300 olt Pattern OLT ENGGEMENT IN VLVE* STUS & NUTS MHINE OLTS Valve Size Thread Size QTY LENGTH QTY LENGTH QTY LENGTH QTY LENGTH F QTY LENGTH G QTY LENGTH 2 5/ /2 5/ / / / / / / / /8-8 4** ** ** ** ** ** / /4-8 4** ** ** ** ** ** / /4-8 4** ** ** ** ** ** / /4-8 4** ** ** ** ** ** / /2-8 4** ** ** ** ** ** 4.50 LUG OY HEX HE MHINE OLTS LUG OY STUS and NUTS * olt lengths & are from face of valve body to minimum depth in lug. Flange & gasket thickness must be added to calculate minimum bolt length. **Special length required for tapped blind holes on either side of the valve shaft at the top and bottom ends of the valve body. FLNGE OLTING REOMMENTIONS Flange etail for NSI Pipe Flanges 300 SHP Series utterfl y Valves FLNGES RILLING OLTING Nominal iameter of iameter of Number olt ircle olt Holes of olts Pipe Size Flange iameter Flange Thickness iameter of olts /8 2-1/ / / / / / / / / / / / /2 121

HD(U) Series Valves HVAC Service Butterfly Valves 2-way and 3-way Assemblies

HD(U) Series Valves HVAC Service Butterfly Valves 2-way and 3-way Assemblies Features / enefits utterfly Valves H(U) Series Valves HV Service utterfly Valves 2-way and 3-way ssemblies elimo resilient seat H(U)... Series utterfly Valves are designed for use in NSI lass 150 piping

More information

Butterfly Valves (BFV)

Butterfly Valves (BFV) Butterfly Valves (BFV) O904-02/12 - Subject to change. Belimo Aircontrols (USA), Inc. Application A comprehensive line of Butterfl y Valves is available in sizes ranging from 2 to 30 in both standard and

More information

F6 Series 2-Way, Victaulic Butterfly Valve

F6 Series 2-Way, Victaulic Butterfly Valve F6 Series 2-Way, Victaulic utterfly Valve psi (2 to 12 ) bubble tight shut-off Long stem design allows for 2 insulation ompletely assembled and tested, ready for installation pplication These valves are

More information

F6100HD, 2-Way Butterfly Valve Resilient Seat, 304 Stainless Steel Disc

F6100HD, 2-Way Butterfly Valve Resilient Seat, 304 Stainless Steel Disc 6100H, 2-Way utterfly Valve Resilient Seat, 304 Stainless Steel isc Product eatures 200 psi (2 to 12 ) and 150 psi (14 to 24 ) 0% leakage, Long stem design allows for 2 insulation, Valve face-to-face dimensions

More information

F7 ANSI Class 150, Industrial Electric Actuator

F7 ANSI Class 150, Industrial Electric Actuator F7 NSI lass 150, Industrial Electric ctuator Reinforced Teflon Seat, 316 Stainless Disc with elimo SY Series ctuator ubble tight shut-off to NSI lass 150 Standards Long stem design allows for 2" insulation

More information

High Performance Butterfly Valves 2 Way Way 2-20 Bray MK Series High Performance Butterfly Valves ANSI Class 150 and 300

High Performance Butterfly Valves 2 Way Way 2-20 Bray MK Series High Performance Butterfly Valves ANSI Class 150 and 300 ray MK Series High Performance utterfly Valves NSI lass 10 and 00 High Performance utterfly Valves 2 Way 2 20 Way 2 20 /2/1 The ray Mcannalok MK Series high performance butterfly valves set the quality

More information

F6100HD, 4, 2-Way Butterfly Valve Resilient Seat, 304 Stainless Steel Disc

F6100HD, 4, 2-Way Butterfly Valve Resilient Seat, 304 Stainless Steel Disc 6100H, 4, 2-Way utterfly Valve Resilient Seat, 304 Stainless Steel isc pplication Valve is designed for use in NSI flanged piping systems to meet the needs of bi-directional high flow HV hydronic applications

More information

F6125HD, 5, 2-Way Butterfly Valve Resilient Seat, 304 Stainless Steel Disc

F6125HD, 5, 2-Way Butterfly Valve Resilient Seat, 304 Stainless Steel Disc 6125H, 5, 2-Way utterfly Valve Resilient Seat, 304 Stainless Steel isc pplication Valve is designed for use in NSI flanged piping systems to meet the needs of bi-directional high flow HV hydronic applications

More information

F6100HD, 4, 2-Way Butterfly Valve Resilient Seat, 304 Stainless Steel Disc

F6100HD, 4, 2-Way Butterfly Valve Resilient Seat, 304 Stainless Steel Disc 6100H, 4, 2-Way utterfly Valve Resilient Seat, 304 Stainless Steel isc pplication Valve is designed f use in SI flanged piping systems to meet the needs of bi-directional high flow HV hydronic applications

More information

BULLETIN SEPTEMBER 2009 BOS OFFSET DISC RESILIENT- SEATED BUTTERFLY VALVES TECHNICAL SPECIFICATIONS

BULLETIN SEPTEMBER 2009 BOS OFFSET DISC RESILIENT- SEATED BUTTERFLY VALVES TECHNICAL SPECIFICATIONS ULLETIN 46.00-2 SEPTEMER 2009 OS OFFSET IS RESILIENT- SETE UTTERFLY VLVES TEHNIL SPEIFITIONS Materials of onstruction 2 s (50-) 8 9 7 Wafer and Lugged esign 10 3 Wafer ody Lugged ody 6 5 4 1 2 2 s (50-)

More information

MK Series High Performance Butterfly Submittal/Technical Data

MK Series High Performance Butterfly Submittal/Technical Data MK Series igh Performance utterfly Submittal/Technical ata ray MK Series igh Performance utterfly Valves NSI lass 150 and 300 ray ontrols ommercial ivision 13788 West Road, Suite 200 ouston, Texas 77041

More information

D I S T R I B U T E D V A L V E S. NAVCO Series E Resilient Seat Butterfly Valve NAVCO

D I S T R I B U T E D V A L V E S. NAVCO Series E Resilient Seat Butterfly Valve NAVCO NVCO Series E Resilient Seat utterfly Valve NVCO SERIES E RESILIENT SET UTTERFLY VLVE Features vailable in sizes 2 in. - 24 in. (50 mm - 600 mm) 200 psi 2 in. - 12 in. (50 mm - 300 mm) 150 psi 14 in. -

More information

08.20 VIC -300 MasterSeal Butterfly Valves

08.20 VIC -300 MasterSeal Butterfly Valves CRBON STEEL PIPE - GROOVED VLVES Vic -300 MasterSeal butterfly valves are designed for pressures ranging from full vacuum to 300 psi/2065 kpa and for bi-directional, dead end services to full working pressure.

More information

G7100S, 3-Way, Mixing Flanged Globe Valve

G7100S, 3-Way, Mixing Flanged Globe Valve pplication This valve is typically used in large ir Handling Units (HU) on heating or cooling coils. This valve is suitable for use in a hydronic system with variable flow. Suitable ctuators Non-Spring

More information

Butterfly Valve Assemblies. Selection Guide. Butterfly Valve Assemblies

Butterfly Valve Assemblies. Selection Guide. Butterfly Valve Assemblies Selection uide PRODUT DSRIPTION Schneider lectric s butterfl y valve line offers a wide range of two- and three-way sizes, along with low pressure pneumatic spring return, electric nonspring return, and

More information

310 Wafer high performance butterfly valve 312 Lugged high performance butterfly valve

310 Wafer high performance butterfly valve 312 Lugged high performance butterfly valve 310 Wafer high performance butterfly valve 312 Lugged high performance butterfly valve Features and Benefits Uninterrupted gasket surfaces help eliminate problems associated with seat retaining screws

More information

G780, 3-Way, Mixing Flanged Globe Valve

G780, 3-Way, Mixing Flanged Globe Valve G780, 3-Way, Mixing langed Globe Valve pplication This valve is typically used in large ir Handling Units (HU) on heating or cooling coils. This valve is suitable for use in a hydronic system with variable

More information

VG4000 Series. High-Capacity/High-Closeoff Electric Zone Valves

VG4000 Series. High-Capacity/High-Closeoff Electric Zone Valves Product ulletin VG000 Issue ate 11/01/01 VG000 Series High-apacity/High-loseoff Electric Zone Valves VG000 Series High-apacity/High-loseoff Electric Zone Valves are designed to regulate the flow of water

More information

Pressure Independent Characterized Control Valves (PICCV)

Pressure Independent Characterized Control Valves (PICCV) Pressure Independent haracterized ontrol s (PIV) Easy direct coupling of actuator with a single screw. Perpendicular mounting ISO flange and square drive head eliminate lateral forces on the stem. Vent

More information

G765, 3-Way, Mixing Flanged Globe Valve

G765, 3-Way, Mixing Flanged Globe Valve G765, 3-Way, Mixing langed Globe Valve pplication This valve is typically used in large ir Handling Units (HU) on heating or cooling coils. This valve is suitable for use in a hydronic system with variable

More information

G765, 3-Way, Mixing Flanged Globe Valve

G765, 3-Way, Mixing Flanged Globe Valve pplication This valve is typically used in large ir Handling Units (HU) on heating or cooling coils. This valve is suitable for use in a hydronic system with variable flow. Suitable ctuators Non-Spring

More information

G7150D, 3-Way, Diverting Flanged Globe Valve

G7150D, 3-Way, Diverting Flanged Globe Valve G7150D, 3-ay, Diverting Flanged Globe Valve pplication This valve is typically used in Large ir Handling Units on heating or cooling coils. This valve is suitable for use in a hydronic system with variable

More information

Series EPDM Seat. Ductile Iron Body, 316 SS, Lug Type Butterfly Valve. Lug-EPDM

Series EPDM Seat. Ductile Iron Body, 316 SS, Lug Type Butterfly Valve. Lug-EPDM Series 600 - EPM Seat Lug Type backed EPM seats. Accompanied by a precision machined 316 SS disc, it offers low operating torque, Lug-EPM Model 600 Series s are epoxy coated with extended neck which makes

More information

KEYSTONE FIGURES 310/312 K-LOK BUTTERFLY VALVES

KEYSTONE FIGURES 310/312 K-LOK BUTTERFLY VALVES 310 - Wafer high performance butterfly valve 312 - Lugged high performance butterfly valve FEATURES GENERAL APPLICATION High performance applications such as steam, chill water, water, utility lines, gasoline,

More information

BUTTERFLY VALVES SHP SERIES. High Performance for a Wide Range of Applications. Advancedd seat and disc design provides zero

BUTTERFLY VALVES SHP SERIES. High Performance for a Wide Range of Applications. Advancedd seat and disc design provides zero UTTRLY VLVS SHP SRIS High Performance for a Wide Range of pplications dvancedd seat and disc design provides zero percent leakage capability at each valve s rated temperature/pressure while maintaining

More information

ilent Silent Operation Proven Performance Cost Effective Silent Check Valves Check Valve

ilent Silent Operation Proven Performance Cost Effective Silent Check Valves  Check Valve ulletin / Silent Operation Proven Performance Cost Effective ilent Check Silent Check s www.valmatic.com Certified Lead-Free NSF/NSI & 7 Certified Feature Highlights Threaded C F C Globe F C E Wafer F

More information

G3 (D) 3-way Globe Valve, Bronze Trim

G3 (D) 3-way Globe Valve, Bronze Trim G3 (D) 3-way Globe Valve, Bronze Trim pplication This valve is typically used in ir Handling Units on heating or cooling coils and Fan Coil Unit heating or cooling coils. Some other common applications

More information

MILLCENTRIC B ALANCING PLUG VALVE

MILLCENTRIC B ALANCING PLUG VALVE ISO 9001 ertified MILLNTI LNING PLUG VLV alancing Service egulation of multi-circuit chilled water and hot water systems is essential to achieve design performance. MILLNTI valves have excellent throttling

More information

Keystone Figures 310/312 K-LOK Butterfly Valves

Keystone Figures 310/312 K-LOK Butterfly Valves 310 - Wafer high performance butterfly valve 312 - Lugged high performance butterfly valve Features General Application High performance applications such as steam, chill water, water, utility lines, gasoline,

More information

PRESSURE INDEPENDENT CONTROL VALVES (epiv & PICCV )

PRESSURE INDEPENDENT CONTROL VALVES (epiv & PICCV ) 7 PRESSURE INDEPENDENT CONTROL VALVES (epiv & PICCV ) Pressure independent valves compensate for pressure variations, performing a continual balancing function to maintain system performance at varying

More information

310 Wafer high performance butterfly valve 312 Lugged high performance butterfly valve

310 Wafer high performance butterfly valve 312 Lugged high performance butterfly valve 310 Wafer high performance butterfly valve 312 Lugged high performance butterfly valve Features and Benefits Uninterrupted gasket surfaces help eliminate problems associated with seat retaining screws

More information

SELECTION. Easily Selectable Easily Serviceable. Interchangeability as easy as 1-2-3

SELECTION. Easily Selectable Easily Serviceable. Interchangeability as easy as 1-2-3 SELETION Terminal Unit Zone Valve 1 Select your valve body Female Thread Solder ouble Union 2 Select your cartridge type hoice of V Hot and hilled Water 50% Glycol Low Pressure Steam Pressure alanced Male

More information

Electronic Butterfly Valve Guide Specifications (For temperatures ranging from 30 F to 250 F)

Electronic Butterfly Valve Guide Specifications (For temperatures ranging from 30 F to 250 F) Electronic Butterfly Valve Guide Specifications (For temperatures ranging from 30 F to 250 F) : 2 through 12 are 200 PSI butterfly valves meeting MSS SP-67 and PI-609 specifications. 14 through 24 are

More information

GP 300 Grooved Butterfly Valve

GP 300 Grooved Butterfly Valve GP 300 Grooved utterfly Valve Nominal Pressure: 20 ar ydraulic Shell Test Pressure 30 ar ydraulic Seat Test Pressure 22 ar 20 ar at: 10º to 100º Suitable Media: Water, Oil, Gas 65 80 100 150 Pipe O/ Item

More information

Butterfly Valves. Quality Valves at Low Cost

Butterfly Valves. Quality Valves at Low Cost utterfly Valves Quality Valves at ow Cost bout Us The Flow+ product le is built around the goal of providg quality valves at competitive prices. It s a goal that has met the needs of various oil and gas,

More information

08.12 Vic-Plug Balancing Valve

08.12 Vic-Plug Balancing Valve Series 377 Vic-Plug balancing valve is the only eccentric grooved end plug valve made specifically for throttling services. For 3 12"/80 300 systems, Victaulic Style 307 transition couplings are available

More information

The Belimo Butterfly Valves

The Belimo Butterfly Valves The Belimo Butterfly Valves Belimo D(U)6..series Butterfly Valves are designed to meet the stringent needs of HVAC applications requiring positive shutoff for liquids. Valve design features 2 1 7 To satisfy

More information

Valves & Flow Control Components Valves & Flow Control Components

Valves & Flow Control Components Valves & Flow Control Components Section 4 Valves & Flow ontrol omponents Valves & Flow ontrol omponents... 106 SJ-200 Low-Profile utterfly Valve... 107 SJ-300N utterfly Valve... 108 SJ-300F utterfly Valve (for Fire Protection)... 110

More information

G6125C, 2-Way, Pressure Compensated Flanged Globe Valve

G6125C, 2-Way, Pressure Compensated Flanged Globe Valve G6125, 2-ay, Pressure ompensated langed Globe Valve pplication This valve is typically used in large air handling units on heating or cooling coils. This valve is suitable for use in a hydronic system

More information

W94. Specifications. Protection: Models Temperature Range Capillary Length Sensing Bulb Valve Body Selection

W94. Specifications. Protection: Models Temperature Range Capillary Length Sensing Bulb Valve Body Selection Temperature Model W91 (No Indicating Dial) W94 (Temperature Indicating Dial) Service Water, Steam, Other Liquids Sizes 1/2 4 onnections Threaded, Union Ends, 125# FLG 250# FLG (optional) ody Material 1/2

More information

Resilient Seat Butterfly Valve with Electric Actuator Two-Way and Three-Way

Resilient Seat Butterfly Valve with Electric Actuator Two-Way and Three-Way Resilient Seat utterfly with Electric ctuator ocument o. 15-030 escription utterfly assemblies provide excellent flow control of hot water, chilled water, condenser water, thermal storage systems, and

More information

Resilient Seated COMMERCIAL. Butterfly Valves 2 Way Way /10/16 COMMERCIAL

Resilient Seated COMMERCIAL. Butterfly Valves 2 Way Way /10/16 COMMERCIAL Bray s NY and B series resilient seated butterfly valves set the design standard for quality, reliability and long life in a wide variety of HV applications. Specifically designed for automated applications

More information

G Series Investment Cast Stainless Steel Ball Valves

G Series Investment Cast Stainless Steel Ball Valves G Series Investment ast Stainless Steel all Valves G1 E Reduced port NPT ends to NSI 1.2.1 One piece body lowout-proof stem (Ring lock with 1 /4" to 3 /8", Latch lock with 1 /2" to 2") omplies with NE

More information

RESILIENT SEATED BUTTERFLY VALVES. Howell Valve & Automation. Toll Free: Howellvalve.com

RESILIENT SEATED BUTTERFLY VALVES. Howell Valve & Automation. Toll Free: Howellvalve.com RESILIENT SEATED BUTTERFLY VALVES Howell Valve & Automation Toll Free: 1-888-469-3557 Howellvalve.com TABLE OF CONTENTS Description Page Index 2 Resilient Standard Features 3 ST Boot Series with BUNA-N

More information

Vic -300 Butterfly Valves

Vic -300 Butterfly Valves R IPS RON STL PIP ROOV VLVS 08.0 Vic -300 utterfly Valves PROUT SRIPTION ear Operator 3" with Position andle Vic -300 butterfly valves are designed for pressures ranging from vacuum to 300 PSI (065 kpa).

More information

BUTTERFLY VALVES SHP SERIES. High Performance for a Wide Range of Applications. Advancedd seat and disc design provides zero

BUTTERFLY VALVES SHP SERIES. High Performance for a Wide Range of Applications. Advancedd seat and disc design provides zero UTTRLY VLVS SHP SRIS High Performance for a Wide Range of pplications dvancedd seat and disc design provides zero percent leakage capability at each valve s rated temperature/pressure while maintaining

More information

Suggested Specifications

Suggested Specifications ISO 9001 Certified Suggested Specifications The Milliken criteria of quality, reliability, safety and value are embodied in the Millcentric Eccentric valve, setting higher standards for dependable performance

More information

Titan Flow Control, Inc. Your pipeline to the future!

Titan Flow Control, Inc. Your pipeline to the future! Titan Flow ontrol, Inc. Your pipele to the future! Series F 75 Wafer > ast Iron Series F 76 ug > uctile Iron esigned accordance with: MSS-S-67 & I 609 olor oded: Orange ody is M Seat lue ody is una-n Seat

More information

MINIMATIC COMPACT - COMPETITIVE - FLOW CONTROL NORTHVALE KORTING LTD

MINIMATIC COMPACT - COMPETITIVE - FLOW CONTROL NORTHVALE KORTING LTD MINIMTI OMPT - OMPETITIVE - FLOW ONTROL NORTHVLE KORTING LT MINIMTI ontrol Valves range of compact, lightweight, low cost control valves for use on liquid steam or gas applications. vailable in 2 way and

More information

VB-9313 Series. Application. Features. Applicable Literature

VB-9313 Series. Application. Features. Applicable Literature V-9313 Series 2-1/2" and 3" Screwed NPT 2-1/2" to 6" 125 Lb. Flanged Three-Way Mixing s General Instructions pplication V-9313 series three-way mixing valves control hot or chilled water in heating or

More information

PRESSURE INDEPENDENT CONTROL VALVES (PICCV& epiv)

PRESSURE INDEPENDENT CONTROL VALVES (PICCV& epiv) 7 PRESSURE INDEPENDENT CONTROL VALVES (& epiv) Pressure independent valves compensate for pressure variations, performing a continual balancing function to maintain system performance at varying loads.

More information

MILLCENTRIC FULL/100% POR T ECCENTRIC PLUG VALVE

MILLCENTRIC FULL/100% POR T ECCENTRIC PLUG VALVE ISO 9001 CERTIFIED MILLCENTRIC FULL/100% POR T ECCENTRIC PLUG VALVE Suggested Specifications The Milliken criteria of quality, reliability, safety and value are embodied in the Millcentric Eccentric valve,

More information

AN ISO 9001 : 2008 COMPANY GLOBE VALVES. Get the edge in process control. Butterfly Valves India Pvt. Ltd.

AN ISO 9001 : 2008 COMPANY GLOBE VALVES. Get the edge in process control. Butterfly Valves India Pvt. Ltd. N ISO 9001 : 2008 OMPNY GLOE VLVES Get the edge in process control utterfly Valves India Pvt. Ltd. Introduction Hi-TEH Manufacturing Programme Valve Type End SME 2 2½ 3 4 5 6 8 10 12 onn. lass DESIGN STNDRD

More information

HIGH PERFORMANCE SEGMENTED V-BALL CONTROL VALVE

HIGH PERFORMANCE SEGMENTED V-BALL CONTROL VALVE HIGH PERFORMNE SEGMENTE V-LL ONTROL VLVE GENERL INFORMTION HIGH PERFORMNE SEGMENTE V-LL ONTROL VLVE High Rangeability: 300:1 Turn down ratio Flow haracteristic: Equal Percentage Low Pressure Recovery Rate:

More information

ATT Series Adjustable PIC Valves 2 Way 1/2-1-1/2 ATT - AutoTouch Terminal

ATT Series Adjustable PIC Valves 2 Way 1/2-1-1/2 ATT - AutoTouch Terminal ½ -1½ - Pressure Independent ontrol Valve - Modulating control valve, dynamic balancing valve and differential pressure control valve in one body. Field adjustable, self-balancing, dynamic flow control

More information

High Performance Butterfly Valves

High Performance Butterfly Valves Tech Bulletin Page 500-11 MAX SEAL HP SERIES High Performance Butterfly Valves Available with Soft and Metal Seating MODEL BL630 Size Range 2 thru 24, optional thru 120 ANSI Class 150//600/900 20 Lug 6

More information

3 Piece Full Port Ball Valves, 1 /4-12 Wide Selection of End Connections

3 Piece Full Port Ball Valves, 1 /4-12 Wide Selection of End Connections Bray High Performance ompany Subsidiary of BRY INTERNTIONL, Inc. 3 Piece Full Port Ball Valves, 1 /4-1 Wide Selection of End onnections Series 7000 & Series 8000 Model 7000-31SS Model 8000-WB Flow-Tek

More information

Durco. Microfinish Ball Valve. The Best Standard Stem Seal In The Industry. Bulletin VM-60e (A4)

Durco. Microfinish Ball Valve. The Best Standard Stem Seal In The Industry. Bulletin VM-60e (A4) P R E S E N T I N G T H E N E W urco Microfinish all Valve F O R H E M I A L S E R V I E S The est Standard Stem Seal In The Industry ulletin VM-6e (A4) (VM-6e) Microfinish all Valve 8/2/2 7:35 AM Page

More information

SPIRA-TROL. ½" to 4" ASME (ANSI) Two-port KEA, KFA and KLA Control Valves

SPIRA-TROL. ½ to 4 ASME (ANSI) Two-port KEA, KFA and KLA Control Valves Page 1 of 11 MNGMNT SYSTMS TI-P375-1 Issue 3 SPIR-TROL ISO 91 ½" to 4" SM (NSI) Two-port K, KF and KL ontrol Valves ert. No. LRQ 9638 Description SPIR-TROL is a range of two-port single seat globe valves

More information

G7 (S) 3-way Mixing Flanged Globe Valve, Bronze or Stainless Steel Trim

G7 (S) 3-way Mixing Flanged Globe Valve, Bronze or Stainless Steel Trim G (S) 3-way Mixing Flanged Globe Valve, Bronze or Stainless Steel Trim pplication This valve is typically used in Large ir Handling Units on heating or cooling coils. This valve is suitable for use in

More information

brands you trust. Tufline High Performance Butterfly Valves Technical Data

brands you trust. Tufline High Performance Butterfly Valves Technical Data brands you trust. Tufline High Performance Butterfly Valves 30-48 Technical Data Unique Valve Seat Designsue Valve Seat Soft Seat Design Xomox is one of the world s leading manufacturers of high performance

More information

DG Series Flanged Globe Valves

DG Series Flanged Globe Valves G Series Globe Valves provide stable and accurate control of both water, 50/50 water Glycol solutions and steam heat exchangers on fan coil units, VAV reheat coils, and air handling units up to 900 GPM.

More information

VB-7000 Series 1/2 to 2 Globe Valves

VB-7000 Series 1/2 to 2 Globe Valves V-7000 Series 1/2 to 2 Globe Valves with MG350V Series SmartX ctuators schneider-electric.com 1 Product Description Schneider Electric MG350V non-spring actuators and V-7000 series two and three-way globe

More information

Technical Documentation Ball Valves

Technical Documentation Ball Valves Technical Documentation all Valves Effective October 2008 elimo Project: ssisi Heights in ochester, Minnesota all Valves all Valve Features and enefits 2...VS/VSS, 3...VS, 6...VS K20951-10/08 - Subject

More information

Design A61D TriAx Triple Offset High Performance Butterfly Valve

Design A61D TriAx Triple Offset High Performance Butterfly Valve pril 2000 ulletin 51.6:61D Trix Design 61D Trix Triple Offset High Performance utterfly Valve Description The Design 61D Trix is a triple offset disk HPV designed for rugged isolation service, available

More information

Your Global Source for Today s Most Popular Solenoid Valves

Your Global Source for Today s Most Popular Solenoid Valves lcon Solenoid Valves Your Global Source for Today s Most Popular Solenoid Valves lcon Solenoid Valves Your Global Source for Today s Most Popular Solenoid Valves lcon Solenoid Valves, a division of International

More information

BY DESIGN. DIFFERENT. BY INTENT.

BY DESIGN. DIFFERENT. BY INTENT. Tech Bulletin Page 51-10 FLO 3pc High Performance Fire Safe Ball Valve Tri-Pro Series Models HPF50 - (316SS) HPF40 - (WB) Full Port: 1/4-3 Pressure Rating 2250 WOG / 250 WSP Models HPS50 - (316SS) HPS40

More information

,, WY VLVS Way Valves - Side ntry Product index... p. - Way Valves - ottom ntry Product index... p. Way Valves - ottom ntry Product index...p. ontents

,, WY VLVS Way Valves - Side ntry Product index... p. - Way Valves - ottom ntry Product index... p. Way Valves - ottom ntry Product index...p. ontents MTRI,, WY VLVS 6P/6P SRIS ,, WY VLVS Way Valves - Side ntry Product index... p. - Way Valves - ottom ntry Product index... p. Way Valves - ottom ntry Product index...p. ontents Introduction... Page - Product

More information

VG2000 Series Cast Iron Flanged Globe Valves

VG2000 Series Cast Iron Flanged Globe Valves Installation Instructions VG2000 Issue ate November 15, 2002 VG2000 Series ast Iron Flanged Globe Valves pplication VG2000 Series ast Iron Flanged Globe Valves are primarily designed to regulate the flow

More information

Butterfly Valve. Assemblies. Make the most of your energy

Butterfly Valve. Assemblies. Make the most of your energy Butterfly Valve Assemblies Make the most of your energy 2 AT A GLANCE 2 to 18 two-way assemblies and 2 to 16 threeway assemblies Chilled/hot water/glycol applications EPDM resilient seats with tongue and

More information

FEATURES. 3 position models can be equipped with special 180 operators offering two 90 steps.

FEATURES. 3 position models can be equipped with special 180 operators offering two 90 steps. 2" 8" (DN 50 200) OTTOM PORTED 3-WY FLNGED LL VLVES Jamesbury bottom ported 3-way ball valves provide a variety of flow paths not commonly found in other 3-way designs.the basic design is suitable for

More information

FS-HP 0001-GB-10.05/GP. Butterfly Valves Series HP

FS-HP 0001-GB-10.05/GP. Butterfly Valves Series HP FS-HP 0001-GB-10.05/GP Butterfly Valves Series HP FLOWSEAL-Butterfly Valves Series HP High Performance process valves for industrial applications Areas of application Flowseal is a leading provider of

More information

COMMERCIAL. Product PRofile

COMMERCIAL. Product PRofile Product PRofile 2 PRODUCT OVERVIEW INtroduction At Bray International, Inc., our business is helping our customers with their flow control requirements. Our modular product line of butterfly, ball and

More information

F6250L, 10, 2-Way Butterfly Valve Resilient Seat, 304 Stainless Steel Disc

F6250L, 10, 2-Way Butterfly Valve Resilient Seat, 304 Stainless Steel Disc F6250, 10, 2-Way Butterfly Valve Resilient Seat, 304 Stainless Steel Disc Application Valve is designed f use in ASI flanged piping systems to meet the needs of bi-directional high flow HVAC hydronic applications

More information

Section 3. Stainless Steel Series. Shurjoint Stainless Steel Piping Series Grooved Mechanical Couplings. Cast Grooved Fittings.

Section 3. Stainless Steel Series. Shurjoint Stainless Steel Piping Series Grooved Mechanical Couplings. Cast Grooved Fittings. Section 3 Stainless Steel Series Shurjoint Stainless Steel Piping Series... 84 Grooved Mechanical ouplings SS-5 Rigid oupling... 85 SS-7 Rigid oupling... 86 SS-7X Rigid oupling... 87 SS-8 Flexible oupling...

More information

Medium Pressure Valves, Fittings and Tubing Pressures to 21,000 psi

Medium Pressure Valves, Fittings and Tubing Pressures to 21,000 psi Medium Pressure Valves, ittings and Tubing MXIMTOR has been designing and manufacturing high pressure equipment for more than thirty years and has a worldwide reputation for quality and reliability, backed

More information

AIR/VACUUM VALVE AND OPTIONAL ANTI-SLAM DEVICE SPECIFICATION

AIR/VACUUM VALVE AND OPTIONAL ANTI-SLAM DEVICE SPECIFICATION AIR/VACUUM AND OPTIONAL ANTI-SLAM DEVICE SPECIFICATION Scope. This specification is intended to cover the design, manufacture, and testing of / in. (3 mm) through 0 in. (00 mm) Air/Vacuum Valves suitable

More information

Fisher Control-Disk Valve NPS 14-24

Fisher Control-Disk Valve NPS 14-24 Control-Disk NPS 14-24 Valve Product ulletin Fisher Control-Disk Valve NPS 14-24 The Fisher Control-Disk valve provides outstanding performance under extreme pressure and temperature conditions. The Control-Disk

More information

B2 Series Characterized Control Valve, Non-Spring Return Actuator

B2 Series Characterized Control Valve, Non-Spring Return Actuator 2 Series Characterized Control Valve, Non-Spring ctuator Two-way Valve with Stainless Steel all and Stem, NPT Female Ends Service: Flow Characteristic: Media Temp Range: Maximum Differential: Pressure

More information

Center line Resilient Seated Butterfly Valves

Center line Resilient Seated Butterfly Valves Center line Resilient Seated utterfly Valves Center Line has been a market leader in quarter-turn valves for more than 0 years, and we have earned a reputation as a supplier of superior valves at competitive

More information

Butterfly Valves. Jenkins Valves 254 Henry Street Brantford, Ontario N3T 5T7 Tel: Tel: Fax:

Butterfly Valves. Jenkins Valves 254 Henry Street Brantford, Ontario N3T 5T7 Tel: Tel: Fax: Butterfly Valves Jenkins Valves 254 Henry Street Brantford, Ontario N3T 5T7 Tel: 519-759-3911 Tel: 800-563-6302 Fax: 519-759-7970 www.craneenergy.com A Crane Co. Company Butterfly Valves Ordering Information

More information

UNIVERSITY SERVICES ANNEX James Madison University Harrisonburg, Virginia State Project Code: Architect s Project Number:

UNIVERSITY SERVICES ANNEX James Madison University Harrisonburg, Virginia State Project Code: Architect s Project Number: SECTION 230523 GENERAL DUTY VALVES FOR HVAC PIPING PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Provisions of the Contract and of the Contract Documents apply to this Section. 1.2 DEFINITIONS A. The following

More information

North. Asia. America. Africa. South. America. Australia. Double Block and Bleed Dual Expanding Plug Valve

North. Asia. America. Africa. South. America. Australia. Double Block and Bleed Dual Expanding Plug Valve North merica Netherlands Europe sia frica South merica ustralia ouble lock and leed ual Expanding Plug Valve CERTIFICTES E X E CUT IO NS V Standard Execution 35 33 7 13 11 6 21 56 12 30 2 7 32 17 23 5

More information

Fisher 9500 Butterfly Control Valve

Fisher 9500 Butterfly Control Valve 9500 Product Bulletin Fisher 9500 Butterfly Control The Fisher 9500 butterfly valve is a fully lined valve for use with corrosive fluids and where tight shutoff is required. The nitrile or PTFE liner totally

More information

TAC TM Butterfly Valve Assemblies

TAC TM Butterfly Valve Assemblies TAC TM Butterfly Valve Assemblies Technical Data TAC s new butterfly valve line offers a wide range of two- and three-way sizes, along with low pressure pneumatic spring return, electric non-spring return,

More information

High Performance Butterfly Valves

High Performance Butterfly Valves High Performance Butterfly Valves FLOWSEAL Flowseal high performance butterfly valves are available in sizes from 2" - 48" in ASME pressure classes 150, 300, and 600 and are available with a diverse range

More information

High Pressure Valves, Fittings and Tubing Pressures to 65,000 psi

High Pressure Valves, Fittings and Tubing Pressures to 65,000 psi igh Pressure Valves, ittings and Tubing MXMTOR has been designing and manufacturing high pressure equipment for more than thirty years and has a worldwide reputation for quality and reliability, backed

More information

CONTROL VALVES CONTROL VALVES. Ball Valve- V-Ball DESCRIPTION FEATURES SPECIFICATIONS

CONTROL VALVES CONTROL VALVES. Ball Valve- V-Ball DESCRIPTION FEATURES SPECIFICATIONS DESRIPTION The VSI is a unique, industrial-grade valve with temperature, pressure, leakage, and close-off ratings that far exceed those of standard commercial grade valves. The assures positive low-leakage

More information

2-WAY AND 3-WAY MOTORIZED VALVES FOR STEAM, VACUUM AND HOT WATER APPLICATIONS

2-WAY AND 3-WAY MOTORIZED VALVES FOR STEAM, VACUUM AND HOT WATER APPLICATIONS R O R P O R T I O N -WY ND 3-WY MOTORIZED VLVES FOR STEM, VUUM ND HOT WTER PPLITIONS VLVE ND TUTOR FETURES Valve Sizes range from ½ inch to 8 inches -Way and 3-Way Single Seated and -Way Double Seated

More information

SVF FLOW CONTROLS. Series # Flanged Standard Port Fire Safe / API th Edition. Performance Engineered I N C O R P O R A T E D

SVF FLOW CONTROLS. Series # Flanged Standard Port Fire Safe / API th Edition. Performance Engineered I N C O R P O R A T E D Series 41 150# Flanged Standard Port Fire Safe / API-607 4 th Edition 1 PIECE REDUCED PORT BALL VALVE UNITS = INCHES SIZE CLASS 150 WEIGHTS L H W 1 1/2 11 6.50 3.86 9.06 2 21 7.01 4.65 9.06 3 40 7.99 5.98

More information

VB-9313 Series. Application. Features. Applicable Literature

VB-9313 Series. Application. Features. Applicable Literature V-9313 Series 2-1/2" and 3" Screwed NPT 2-1/2" to 6" 125 Lb. Flanged Three-Way Mixing s General Instructions pplication V-9313 series three-way mixing valves control hot or chilled water in heating or

More information

Instrument Ball Valves

Instrument Ball Valves www.swagelok.com Instrument all s 40 Series On-off, switching, and crossover flow paths Working pressures up to 3000 psig (206 bar) Temperatures from 50 to 150 (10 to 65 ) Low-temperature service option

More information

CONTROL VALVES CONTROL VALVES BALL VALVES VBN2, VBN3 SERIES DESCRIPTION FEATURES SPECIFICATIONS

CONTROL VALVES CONTROL VALVES BALL VALVES VBN2, VBN3 SERIES DESCRIPTION FEATURES SPECIFICATIONS ONTROL VLVS LL VLVS VN2, VN SRIS SRIPTION The VN2 and VN Series are Honeywell's characterized flow, low torque, two- and three-way ball valves. They are designed to provide v ratings that closely match

More information

Valve Selection. 1. Function and service considerations

Valve Selection. 1. Function and service considerations 1. Function and service considerations Valve Selection Selection Valves serve the purpose of controlling the fluids in building services piping. Valves are produced in a variety of design types and materials.

More information

Z2 050 Q -J +CQB 24 -SR -L

Z2 050 Q -J +CQB 24 -SR -L ZoneTight Zone Valve () (½ to ¾ ) Nomenclature Z2 050 Q -J +CQB 24 -SR -L Valve Type Z2 = 2-way Z3 = 3-way ZoneTight Chrome Plated Brass Ball and Brass Stem Valve Size 050 = ½ 075 = ¾ Quick Connect E =

More information

VB-9213 Series. Application. Features. Applicable Literature

VB-9213 Series. Application. Features. Applicable Literature VB-9213 Series 2-1/2" and 3" Screwed NPT 2-1/2" to 6" 125 Lb. Flanged Stem Down to Close Two-Way Valves General Instructions pplication VB-9213 series single seat, stem down to close, twoway valves control

More information

Titan Flow Control, Inc. Your pipeline to the future!

Titan Flow Control, Inc. Your pipeline to the future! TITN Titan Flow ontrol, Inc. Your pipele to the future! eries F 75 Wafer > ast Iron eries F 76 ug > uctile Iron esigned accordance with: M--67 & I 609 olor oded: Orange ody is M eat lue ody is una-n eat

More information

Electro Controls. Valves / Linkages WattsIndustries.co.uk

Electro Controls. Valves / Linkages WattsIndustries.co.uk Electro Controls Valves / Linkages - 07 WattsIndustries.co.uk valves / linkages Section MOUNTING INSTRUCTIONS FOR LINKGES EE.. M K / EE..ES / EE..RD EE..MK UTO MNUL UTO MNUL UTO MNUL. Push the valve spindle

More information

Aloyco. Corrosion Resistant Valves. The First Name In Corrosion Resistant Valves

Aloyco. Corrosion Resistant Valves. The First Name In Corrosion Resistant Valves loyco Corrosion Resistant s The First Name In Corrosion Resistant s Stainless Steel s General Index Figure No. Type Pressure Class End Connection Material vailable Size Range Catalog Page 0 Gate, RS 00

More information

3-Way Linked Globe Valve Assemblies with Linear Series Actuators

3-Way Linked Globe Valve Assemblies with Linear Series Actuators Linked Globe Valve ssemblies with Linear Series ctuators Note: hoose a valve assembly having a close-off pressure capability sufficient for the application. Not all valve body and actuator combinations

More information