Series F Shaft Mounted Geared Motor- Version 3

Transcription

1 Series F Shaft ounted Geared otor- Version 3 Technical p to - 45kW/ 8000 Nm Geared otor CF3.01-GBD-0 18

2 PRODCTS IN TE RANGE Series A Worm Gear units and geared motors in single & double reduction types Series BD Screwjack worm gear unit Series BS Worm gear unit Series C Right angle drive helical worm geared motors & reducers Series F Parallel shaft helical geared motors & reducers Series G elical parallel shaft & bevel helical right angle drive gear units Series Large helical parallel shaft & bevel helical right angle drive units Series J Shaft mounted helical speed reducers Series K Right angle helical bevel helical geared motors & reducers Series In-line helical geared motors & reducers Roloid Gear Pump Lubrication and fluid transportation pump Series P Planetary Foot and flange mounted planetary units Series X Elign Gear Torsionally rigid, high torque coupling Series X Elflex Pin and bush elastomer coupling Series X Nylicon Gear coupling with nylon sleeve otors Full range of IEC motors We offer a wide range of repair services and many years experience of repairing demanding and highly critical transmissions in numerous industries. We can create custom engineered transmission solutions of any size and configuration.

3 CONTENTS PAGE General Description nit Designation Explanation And se Of Ratings And Service Factors Load Classification By Applications Selection Procedure For otorised nits Options otor Adapters Lubrication ounting Posistions OTORISED otor Details Additional otor Features Additional Gearbox Features Exact Ratios Selection Tables- Geared otors Dimension Table- Geared otors otorised Backstop odule otorised Options REDCER Overhung & Axial Loads On Shafts Thermal Power Ratings Ratings - Input Power / Torque Dimension Sheets - Speed Reducer Fan Cooled nits Reducer Backstop odule OTPT OPTIONS Dimensions - Torque Bushes & Flange Dimensions - B14 (C) Flange nits Dimensions - Standard Bore - Assmembly / Disassmbly Dimensions - Taper Release Bushing Dimensions - Shrink Disk Dimensions - Screw Conveyor Shipping Specifications Safety Information 69 70

4 GENERAL DESCRIPTION Series F right angle drive helical bevel helical geared motors offer ratios from 5:1 to 100:1 in two stages,up to 320:1 in three stages and 5000:1 in four stages. aximum output torque capacity up to Lb-in otors up to 50P can be fitted. The Series F geared motor is primarily designed as a shaft mounted unit incorporating an integral torque reaction bracket, and can be supplied with rubber bushes to cushion the torque reaction. Shaft mounted units are supplied with a hollow bore and keyway or alterantively with shaft bushings. nits may also be supplied with a single extended outputshaft, side tappings are provided to attach feet for base mounting, nits may also be supplied with an output flange suitable for mounting horizontally or vertically. All variants cn be fitted with a motor of your preference or with a standard own brand motor, alternatively they can be supplied with an input shaft assembly. Adding to the range of geared motors this product takes advantage of our many years of accumulated design expertise together with the use of high quality materials and components. The end result is a series of speed reducing geared motors offering high load carrying capacities, increased efficiency, quiet running and reliability. The Range Includes 9 sizes, with the following options: Shaft ounted Reducer Double / Triple Reduction F T R A otorised - Double / Triple Reduction Shaft ounted F T N N - 1 D. 7 5 A - - Version T - standard unit with torque bushes Version W - standard unit without torque bushes Version F - standard unit with outputflange nit Types: nit type - otorised with IEC standard motor nit type N - otorised with NEA standard motor nit type G - nit to allow fitting of IEC motor nit type A - nit to allow fitting of NEA motor nit type R - Reducer unit Design Features Include: Patented standard motor connection (IEC or NEA) Ability to fit double oil seals, on output shaft or reducer input shaft as required. All units are dimensionally interchangeable with other major manufacturers. Braked geared motors are available as standard. nits are manufactured and assembled from a family of modular kits for distributor friendliness minimising inventory and maximising availability. otorised units can be fitted with a backstop module and reducer units can be fitted with a backstop and fan. otorised Double / Triple Reduction with Shaft and Flange F F N N - 1 D. 7 5 A - - otorised Quadtuple Reduction Shaft ounted F T N A - 1 D. 1 2 A - - As improvements in design are being made continually this specification is not to be regarded as binding in detail and drawings and capacities are subject to alteration without notice. Certified drawings will be sent on request. Shaft ounted Reducer Quadruple Reduction F T R A B C

5 NIT DESIGNATIONS Gearbox Codes otor Codes 1 - Series F Range F 2, 3 - Size of nit No of Reductions 5 - Revision Version 3 N A G R S W X Y Z 2-4 6, 7, 8 - Nominal Overall Ratio e.g nit Version STD with Torque Bush 10 - Type of nit Example STD without Torque Bush STD with Flange F T N A P 1 D 4. 0 B - - T W - otorized with NEA standard motor F - nit to allow fitting of NEA motor (customer own motor) - otorized with IEC standard motor - nit to allow fitting of IEC motor (customer own motor) - Reducer unit Series Size of nit - Reducer unit with fan kit No of Reductions Revision Version - Reducer unit with backstop CCW rotation - Reducer unit with backstop CW rotation Nominal Overall Ratio - Reducer unit with fan and backstop CW rotation - Reducer unit with fan and backstop CCW rotation nit Version Type of nit Shaft otor Adaptor * This Page ay Be Photocopied Allowing The Customer To Enter Their Order ounting Position 2 Geared otor Power 18 - No of otor Poles - No motor 60 z 50 z 4 Pole (Std) 1800 rpm B 1500 rpm A 4 Pole (igh)1800 rpm 6 Pole (Std) 1200 rpm 6 Pole (igh)1200 rpm L D N 1500 rpm 1000 rpm 1000 rpm K C 2 Pole 8 Pole 3600 rpm 900 rpm F 3000 rpm E 750 rpm G S Dual speed or special motor e.g For reducer and non standard motor types enter B N A Y Screw Conveyor S Taper Release Shaft Bushing * * Dependant on Type & Bore size see dimesion page 20 - Additional Gearbox Features Double Oil Seal, otorized Backstop etc e.g. - F 19 - Additional otor Features e.g. - A For Types Without otor Enter - 15, 16, 17 - Geared otor Powers otor P required (For 50 z enter kw) 13, 14 - ounting Position e.g otor Adaptor For nit Types Column 10 Entries, N,, E, G or A See Pages 9 and 10 For All Other Types Enter 11 - OTPT SAFT Standard Single Extension Standard ollow Shaft Shrink Disc No of otor Poles Additional otor Features Additional Gearbox Features ** Looking on Inputshaft ounting Position 1 (See unit handings page) *** Non Standard and anding - Consult Application Engineering -

6 Gear unit selection is made by comparing actual loads with catalogue ratings. Catalogue ratings are based on a standard set of loading conditions, whereas actual load conditions vary according to type of application. Service Factors are therefore used to calculate an equivalent load to compare with catalogue ratings. i.e. Equivalent Load = Actual Load x Service Factor echanical Ratings and Service Factors Fm and Fs echanical ratings measure capacity in terms of life and/or strength, assuming 10 hr/day continuous running under uniform load conditions. Catalogue ratings allow 100% overload at starting, braking or momentarily during operation up to 10 hours per day. The unit selected must therefore have a catalogue rating at least equal to half maximum overload. echanical Service Factor Fm (Table 1) is used to modify the actual load according to daily operating time, and type of loading. Load characteristics for a wide range of applications are detailed in Table 3 opposite, which are used in deciding the appropriate Service Factor Fm from Table 1. If overloads can be calculated, or accurately assessed, actual loads should be used instead of Fm. For units subjected to frequent stop/starts overloads in excess of 10 times/day multiply factor Fm x Factor Fs (table 2). For applications where units are to operate in extremely dusty or moist/humid atmospheres unit selection should be referred to application engineering. Table 1. echanical Service Factor (Fm) EXPLANATION & SE OF RATINGS & SERVICE FACTORS Prime over Electric otor, Steam Turbine or ydraulic otor Duration of Service ours per day < > 10 niform mass acceleration factor < Load Classification-Driven achine oderate mass acceleration factor < eavy mass acceleration factor < ulti-cylinder Internal Combustion Engine < > Single-cylinder Internal Combustion Engine < > ass acceleration factor = all external moments of inertia * moment of inertia of driving motor * calculated with reference to the motor speed Table 2. Number of Starts Factor (Fs) Start / Stops per hour (1) p to > 200 Factor Fs Note: Intermediate values are obtained by linear interpolation 3

7 LOAD CLASSIFICATION BY APPLICATIONS Load Classifications - =niform Load =oderate Shock Load =eavy Shock Load =Consult our Engineers Agitators Pure liquids Liquids and solids Liquids variable density Blowers Centrifugal Lobe Vane Brewing & distilling Bottling machinery Brew Kettles Cookers ash tubs Scale hopper Can filling machinery Crane knife Car dumper Car puller Clarifier Classifier Clay wokring machinery Brick press Briquette machine Clay working machinery Plug mill Compressors Centrifugal Lobe Reciprocating ulti cylinder Single cylinder Conveyors- Light duty uniform load Apron Assembly Belt Bucket Chain Flight Oven Screw Conveyors - eavy duty uniform load Apron Assembly Belt Bucket Chain Flight Live roll Oven Reciprocating Screw Shaker Cranes Crusher Ore Stone Sugar Dredger Cable reals Conveyors Cutter head drive Pumps Screen drive Stackers Winches Elevators Bucket - niform load Bucket - eavy load Bucket - Continuous Centrifugal discharge Escalators Freight Gravity discharge Passenger lifts Fans Centrifugal Cooling towers Induced draft Forced draft Fan - Large diameter induced draft Fan - Light, small diameter Feeders Apron Belt Disc Reciprocating Screw Food industry Cereal cooker Dough mixer eat grinder eat slicer Generators - not welding ammer mills oists eavy duty edium duty Skip hoist Laundry Tumbler Washer Line shafts eavy duty Light duty Lumber industry Barkers Burner conveyor Chain/ Drag saw Chain transfer Chain way transfer De- barking drum Edger feed Gang feed Green chain Live roll Log deck Log haul Log turning Log converyor Of bearing roll Planer feed chaines Planer hoist Re-saw conveyor Roll cases Slab conveyor Sorting table - triple hoist Triple hoist - Drive /conveyor Transfer converor Transfer roll Tray drive Trimmer feed Waster conveyor Small waste conveyor (belt) Small waste conveyor (chain) achine Tools Bending roll Punch press Notching press Plate planer Other machine tools ain drive Aux drive etal mills Carriage/main drive Draw bench Dryer Flattening machinery Pinch drive Reversing slitters Scrubber rolls Table conveyors Group drives Individual drives Table conveyors- reversing Wire draw Wire roll ills Cement kiln Dryer, Cooler Kiln (other) Rod plain Rod wedge bar Rotary/ Ball Tumbling barrel ixers Concrete Constant density Variable density Oil industry Chiller s Oil well pump Filter press Rotary kiln Paper industry Agitator (mixer) Barker (hydraulic) Barker (mechanical) Barking drum Beater & Pulper Bleacher Calednders Calenders- super Converting machine Conveyors Couch Cutters - plates Cylinders Dryers Felt stretcher Felt whipper Jordans Log haul achine real Presses Stock chest Suction roll Washers & thickeners Winders Printing presses Pullers Barge haul Pumps Centrifugal proportioning Proportioning Reciprocating Single acting 3+ cylinders Double acting 2+ cylinders Single acting 1 & 2 cylinders Double acting 1 cylinder Rotary- gear type Rotary- lobe type/ vane Sand muller Sewage treatment Bar screen Chemical feeder Collector Dewatering screw ixers Scum breaker Thickness Vacuum filters Screens Air washing Rotary, stone or gravel Traveling water intake Slab pushers Slewing Steering gear Stokers Sugar industry Can knife Crusher ills Textile industry Batchers Calenders Cards Dry cans Dryers Dyeing machinery Knitting machinery Looms angles Nappers Pads Range drive Slashers Soapers Spinners Tenter frame Washers Winders Windlass 4

8 SELECTION PROCEDRE FOR OTORISED NITS EXAPLE APPLICATION DETAILS Absorbed power of driven machine = 1.4 P speed of gearbox or Input speed of machine = 65 rev/min Application = niformly loaded belt conveyor Duration of service (hours per day) = 24hrs ounting position = 1 Ambient temperature = 75 o F Running time (%) = 100% 1 DETERINE ECANICAL SERVICE FACTOR (Fm) Refer to Load Classification by Application, table 3. Application = niformly loaded belt conveyor Conveyors-uniformly loaded or fed apron = niform load assembly belt bucket chain Refer to mechanical service factor (Fm), table 1, page 3 Duration of service (hours per day) = 24hrs Prime mover Electric motor, steam turbine or hydraulic motor Duration of servicehrs per day Load classification-drive oderate niform Shock < > DETERINE REQIRED OTPT TORQE AT GEARBOX OTPTSAFT Absorbed = Absorbed P x output torque Gearbox output speed 1.4 x = 1357 lb-in 65 Therefore mechanical service factor (Fm) = SELECT GEARED OTOR Refer to selection table one motor size larger than absorbed power. Absorbed power = 1.4 P, therefore refer to 1.5 P selection table. Always select from 4 POLE selection table in the first instance as this offers a more economical solution. Required output speed of gearbox = 65 rev/min 1.5 P 4 POLE N2 rpm Speed i Ratio 2 lb-in Torque Fm lbf LB nit Designation Overhung Column Entry 1 Through 20 Load Spaces to be filled when entering order Service Factor Weight of base mount unit F _ N 1.5B TC F _ N 1.5B TC F _ N 1.5B TC F _ N 1.5B TC F _ N 1.5B TC F _ N 1.5B TC F _ N 1.5B TC F _ N 1.5B TC otor Size Go to point 4 5

9 SELECTION PROCEDRE FOR OTORISED NITS 4 CECK OTPT TORQE torque (2) of selected unit must be equal or more than required output torque at gearbox outputshaft. Required output torque at gearbox outputshaft = 1357 lb.in 1.5 P 4 POLE N2 rpm Speed i Ratio 2 lb.in Torque Fm lbf nit Designation lb Service Factor Overhung Load Column Entry 1 Through 20 Spaces to be filled when entering order Weight of base mount unit F _ N 1.5B TC F _ N 1.5B TC F _ N 1.5B TC F _ N 1.5B TC F _ N 1.5B TC F _ N 1.5B TC F _ N 1.5B TC F _ N 1.5B TC otor Size Selected unit's output torque (2) = 1374 lb,in therefore unit is acceptable 5 CECK SERVICE FACTOR Service factor (Fm) of selected unit must be equal or more than required service factor. Required service factor of gearbox = P 4 POLE N2 rpm Speed i Ratio 2 lb.in Torque Fm Service Factor lbf Overhung Load nit Designation Column Entry 1 Through 20 Spaces to be filled when entering order lb Weight of base mount unit F _ N 1.5B TC F _ N 1.5B TC F _ N 1.5B TC F _ N 1.5B TC F _ N 1.5B TC F _ N 1.5B TC F _ N 1.5B TC F _ N 1.5B TC otor Size Selected unit's service factor (Fm) = 1.60 therefore unit is acceptable. 6 CECK OVERNG LOADS If sprocket, gear, etc is mounted on the output shaft then refer to Overhung Loads Procedure and compare with allowable overhung load (N) of selected unit Allowable overhung load (N) must be equal or more than calculated overhung load (P) 1.5 P 4 POLE N2 rpm Speed i Ratio 2 lb.in Torque Fm lbf nit Designation lb Service Factor Overhung Load Column Entry 1 Through 20 Spaces to be filled when entering order Weight of base mount unit F _ N 1.5B TC F _ N 1.5B TC F _ N 1.5B TC F _ N 1.5B TC F _ N 1.5B TC F _ N 1.5B TC F _ N 1.5B TC F _ N 1.5B TC otor Size NOTE: If any of the following conditions occur then consult Application Engineering:- a) Inertia of the Driven achine (Referred to motor speed) >10 b) Ambient temperature is above 100 o F Inertia of Gear nit plus otor 6

10 OTPT BORE OPTIONS Column 11 Entry m1 m2 v3 Inch ollow Shaft etric ollow Shaft A OD Om3 T m m Size Bore Type Col 11 Entry Dimensions (etric in mm) Ø D m m1 m2 Øm3 T v3 F02 F03 F04 F05 F06 F07 F08 F09 F10 etric / x50 Inch A / NF x 2 etric / x50 Inch A / NF x 2 etric / x55 Inch A / NF x 2.25 etric / x70 Inch A / NF x 2.75 etric / x70 Inch A / NF x 2.75 etric / x70 Inch A / NF X 2.75 etric / x80 Inch A / NF X 3.25 etric / x80 Inch A / NF X 3.25 etric / x80 Inch A / NF X

11 OTPT SAFT OPTIONS Column 11 Entry etric Single Extension C L11 L12 t Inch Single Extension N u Od w L Size Shaft Type Col 11 Entry Dimensions (etric in mm) ø d L L11 L12 t u W F02 F03 F04 F05 F06 F07 F08 F09 F10 etric C Inch N etric C / x 1.5 x 22 Inch N " / " 1.85" * 1.69" 1.11" 0.250" 0.375" x 0.75" etric C / x 1.75 x 28 Inch N "/ " 2.20" * 2.13" 1.36" 0.250" 0.5" NF x 1.13" etric C / x 2.0 x 36 Inch N " / " 2.60" * 2.50" 1.51" " NF x 1.5" etric C / x 2.0 x 36 Inch N 1.625" / 1.624" 3.00" * 2.50" 1.78" 0.375" 0.625" NF x 1.5" etric C / x 2.0 x 36 Inch N 2.000" / 1.999" 3.74" * 3.00" 2.23" 0.500" 0.625" NF x 1.5" etric C / x 2.5 x 42 Inch N " / " 4.488" * 4.00" 2.65" 0.625" 0.75" NF x 1.65" etric C / x 2.5 x 42 Inch N 2.875" / 2.874" 5.315" * 5.00" 3.20" 0.750" 0.75" NF x 1.65" etric C / x 3.0 x 50 Inch N 3.625" / 3.624" 6.772" * 6.38" 4.01" 0.875" 0.75" NF x 1.65" * Inch shafts have an open ended keyway, therefore no 'L11' dimension is required 8

12 Double Reduction nits OTOR ADAPTERS NEA otor C Face- Column 12 entry F0223 F0323 F0423 F0523 F0623 F0723 F0823 F0923 F1023 otor C T T T - Q - Q - Q /145TC V W V W V W - R - R - R - N /184TC X - X - X - S T S T S T J P - S - P 213/215TC V K Q - T - Q 254/256TC W - L P L R 284/286TC Q V S 324/326TC R W N T 364/365TC /405TC /445TC IEC otor B14- Column 12 entry otor F0223 F0323 F0423 F0523 F0623 F B K B K B K - G - G - G 90 D R D R D R Z J Z J - J 100 E S E S E S B L B L B L 112 E S E S E S B L B L B L D N IEC otor B5- Column 12 entry F0223 F0323 F0423 F0523 F0623 F0723 F0823 F0923 F1023 otor F F F F - F - V - V G G G G - G - D - D A J A J A J W F W F - F - D - E C Q C Q C Q Y Y - - E - F A K A K A K A F - G - E A K A K A K A F - G - E N P N P C B G - - F E P C A J A G B K B C L C J D D K

13 OTOR ADAPTERS Triple Reduction nits NEA otor C Face- Column 12 entry otor F0233 F0333 F0433 F0533 F0633 F0733 F0833 F0933 F C Q Q - 143/145TC W W W W W R R N - 182/184TC T T P S 213/215TC V Q T 254/256TC /286TC V 324/326TC W IEC otor B14- Column 12 entry otor F0233 F0333 F0433 F0533 F0633 F0733 F K K K K K G G 90 R R R R R J J 100 S S S S S L L 112 S S S S S L L N IEC otor B5- Column 12 entry otor F0233 F0333 F0433 F0533 F0633 F0733 F0833 F0933 F F F F F F V G G G G G D J J J J J F F D E 90 Q Q Q Q Q E F K K F G K K F G G J K L

14 OTOR ADAPTERS IEC & NEA Quadruple Reduction nits NEA otor C Face- Column 12 entry otor F0343 F0443 F0543 F0643 F0743 F0843 F0943 F C Q Q Q 143/145TC W W W W W R R R 182/184TC T T T 213/215TC V IEC otor B14- Column 12 entry F0343 F0443 F0543 F0643 F0743 F0843 F0943 F1043 otor K K K K K G G G 90 R R R R R J J J 100 S S S S S L L L 112 S S S S S L L L N IEC otor B5- Column 12 entry F0343 F0443 F0543 F0643 F0743 F0843 F0943 F1043 otor F F F F F V V - 71 G G G G G D D - 80 J J J J J F F F 90 Q Q Q Q Q K K K K K K P P P 11

15 F02, F03, F04, K05, F06 & F07 nits & Primary nits used for Quintuple Reduction, are supplied factory filled with EP mineral oil (Grade 6E) appropriate to the intended mounting position. If the unit is supplied without lubricant the unit must be filled with the correct lubricant and quantity as listed below: F08, F09, & F10 nits require filling with EP mineral oil (Grade 6E) Lubricant quantities are approximate fill until oil escapes from the level plug hole, fit ventilator plug (when supplied) in the appropriate position for the required mounting position (see installation and maintenance instructions) Temperature Limitations The standard lubricant is suitable for operation in ambient temperatures of 32 to 95 F, Outside of this range consult Table 1,or consult Application Engineering. Lubricant Quantities (gallons) 1 gallon (S) = 3.79 Liters ounting Position ounting Position ounting position ounting Position Double Reduction 23 o F - 68 o F (E) -22 o F - 68 o F () Size F0223 F0323 F0423 F0523 F0623 F0723 F0823 F0923 F Triple Reduction Size F0233 F0333 F0433 F0533 F0633 F0733 F0833 F0933 F1033 Size Size Table 1 Oil Grades Lubricant EP ineral Oil (type E) Polyalphaolefin based Synthetic (type ) Quadruple Reduction F0343 F0443 F0543 F o F - 95 o F 68 o F o F 5E (VG 220) 6E (VG 320) 7E (VG 460) 5 (VG 220) 5 (VG 220) 6 (VG 320) Primary Secondary Primary Secondary Primary Secondary Primary Secondary 0122 F F F F F0743 F0843 F0943 F1043 Ambient temperature range Primary Secondary Primary Secondary Primary Secondary Primary Secondary 0322 F F F F LBRICATION 12

16 ONTING POSITIONS Column 13 entry * * Not Recommended for Geared otors - Consult Application Engineering Gear nits selected for use in mounting positions 5 and 6 should only be used with overall ratios greater or equal to those shown in the table below Size Input Speed (rpm) < 1000 < 1500 < 1800 > 1800 F08 All All All F09 All F Consult Application Engineering ounting Positions - shown as motorised - applies also for reducers Column 14 entry C D A X C D A Column 14 entry Terminal Box Position (X) F02 F03 - F10 A 15 0 B C D Reducer or no motor fitted B B k 13 L15

17 NOTES 14

18 OTORISED SERIES F 15

19 NEA OTOR DETAILS NEA Standard otors A k0 OBF OAJ OBD OAJ O Og OTOR FRAE SIZE Ø BD Ø AJ Ø AK Ø A ko max Ø g BF TAP NC 56C / TC/145TC /8-16 A k0 OBF OAJ OBD OAK O Og OTOR FRAE SIZE Ø BD Ø AJ Ø AK Ø A ko * max Øg BF TAP NC 182TC/184TC / TC/215TC / TC/256TC / TC/286TC / TC/326TC / TC/365TC / TC/405TC / TC/445TC /8-11 * otor lengths for own brand standard motors. These lengths may vary if alternative motor is fitted. 16

20 ADDITIONAL OTOR FEATRES Additional otor Features - column 19 entry Column 19 Entry Brake otor and Release on Brake Forced Ventilation/ Constant Blower (TECB) Thermistor Special - A B C D E F G K L S Please refer to Application Engineering for details of the following additional motor features - PGF encoder flange - Wash down - Customised brake torque - Separate brake supply - Aluminium fan - Anti Condensation heater - Bi-metal temperature detectors, Thermostat - EExEIIT3 - Ex na II T3 - IP56 - IP65 - etal fan cover - Rain cowl - Separate terminal box 17

21 ADDITIONAL GEARBOX FEATRES Additional Gearbox Features - column 20 entry Column 20 Entry Double Oil Seals on Shaft * otorised Backstop Oil Level Glass F06- F10 CW Rotation CCW Rotation Special - A B C D E F G I J K L Please refer to Application Engineering for details of the special additional gearbox features for example :- - Prime paint only - Wash down - BISSC compatible - Special oil (food compatible, bio-degradable, different viscosities etc) * IEC Frame Sizes , and NEA frame sizes 182TC - 326TC 18

22 EXACT RATIOS Exact Ratios - Double Reduction Column Entry F0223 F0323 F0423 F0523 F0623 F0723 F0823 F0923 F Exact Ratios - Triple Reduction Coumn Entry F0233 F0333 F0433 F0533 F0633 F0733 F0833 F0933 F Exact Ratios - Quadruple Reduction Column Entry F0343 F0443 F0543 F0643 F0743 F0843 F0943 F C C C C C C C C C C C C C C C

23 0.25 P 4 Pole 1750 rpm nominal input speed 4 POLE N2 rpm Speed i Ratio 2 lb.in Torque Fm lbf nit Designation lb Service Factor Overhung Load Column Entry 1-20 Blanks to be filled when entering order SERIES F SELECTION TABLES GEARED OTORS Weight of base mount unit F _ N.25B C F _ N.25B C F _ N.25B C F _ N.25B C F _ N.25B C F _ N.25B C F _ N.25B C F _ N.25B C F _ N.25B C F _ N.25B C F _ N.25B C otor Size F _ N.25B C F _ N.25B C F _ N.25B C F _ N.25B C F _ N.25B C F _ N.25B C F _ N.25B C F _ N.25B C F _ N.25B C F _ N.25B C F _ N.25B C F _ N.25B C F _ N.25B C F _ N.25B C F _ N.25B C F _ N.25B C F _ N.25B C F _ N.25B C F _ N.25B C F _ N.25B C F _ N.25B C F _ N.25B C F _ N.25B C F _ N.25B C F _ N.25B C F _ N.25B C F _ N.25B C F _ N.25B C F _ N.25B C F _ N.25B C F _ N.25B C F _ N.25B C F _ N.25B C F _ N.25B C F _ N.25B C F _ N.25B C F _ N.25B C F _ N.25B C F _ N.25B C F _ N.25B C F _ N.25B C F _ N.25B C F _ N.25B C F _ N.25B C F _ N.25B C F _ N.25B C F _ N.25B C NOTE Other output speeds are available using 2 and 8 pole motors. Consult Application Engineering F _.25B C F _.25B C F _.25B C F _.25B C F _.25B C F _.25B C F _.25B C 20

24 0.25 P 4 Pole 1750 rpm nominal input speed N2 rpm Speed i Ratio 2 lb.in Torque Fm lbf nit Designation lb Service Factor Overhung Load Column Entry 1-20 Blanks to be filled when entering order SERIES F SELECTION TABLES GEARED OTORS Weight of base mount unit F _ N.25B C F _ N.25B C otor Size F _ N.25B C F _ N.25B C F _ N.25B C F _ N.25B C F _ N.25B C F _ N.25B C F _ N.25B C F _ N.25B C F064310C_ N.25B C F064311C _ N.25B C F _ N.25B C F _ N.25B C F _ N.25B C F _ N.25B C F _ N.25B C F _ N.25B C F _ N.25B C F074310C_ N.25B C F074311C _ N.25B C F074312C_ N.25B C F074314C_ N.25B C F074316C_ N.25B C F074318C_ N.25B C F074320C_ N.25B C F _ N.25B C F _ N.25B C F084310C_ N.25B C F084311C _ N.25B C F084312C_ N.25B C F084314C_ N.25B C F084316C_ N.25B C F084318C_ N.25B C F084320C_ N.25B C F084322C_ N.25B C F084325C_ N.25B C F084328C_ N.25B C F084332C_ N.25B C F084336C_ N.25B C F094311C _ N.25B C F094312C_ N.25B C F094314C_ N.25B C F094316C_ N.25B C F094318C_ N.25B C F094320C_ N.25B C F094322C_ N.25B C F094325C_ N.25B C F094328C_ N.25B C F094332C_ N.25B C F094336C_ N.25B C F094340C_ N.25B C F094345C_ N.25B C F094350C_ N.25B C NOTE F104322C_ N.25B C F104325C_ N.25B C F104328C_ N.25B C F104332C_ N.25B C F104336C_ N.25B C F104340C_ N.25B C F104345C_ N.25B C F104350C_ N.25B C Other output speeds are available using 2 and 8 pole motors. Consult Application Engineering 21

25 0.33 P 4 Pole 1750 rpm nominal input speed NOTE Other output speeds are available using 2 and 8 pole motors. Consult Application Engineering N2 rpm Speed i Ratio 2 lb.in Torque Fm lbf nit Designation lb Service Factor Overhung Load Column Entry 1-20 Blanks to be filled when entering order SERIES F SELECTION TABLES GEARED OTORS Weight of base mount unit F _ N.33B C F _ N.33B C F _ N.33B C F _ N.33B C F _ N.33B C F _ N.33B C F _ N.33B C F _ N.33B C F _ N.33B C F _ N.33B C F _ N.33B C F _ N.33B C F _ N.33B C F _ N.33B C F _ N.33B C F _ N.33B C F _ N.33B C F _ N.33B C F _ N.33B C F _ N.33B C F _ N.33B C F _ N.33B C F _ N.33B C F _ N.33B C F _ N.33B C F _ N.33B C F _ N.33B C F _ N.33B C F _ N.33B C F _ N.33B C F _ N.33B C F _ N.33B C F _ N.33B C F _ N.33B C F _ N.33B C F _ N.33B C F _ N.33B C F _ N.33B C F _ N.33B C F _ N.33B C F _ N.33B C F _ N.33B C F _ N.33B C F _ N.33B C F _ N.33B C F _ N.33B C F _ N.33B C F _ N.33B C F _ N.33B C F _ N.33B C F _ N.33B C F _ N.33B C F _ N.33B C F _ N.33B C F _ N.33B C F _ N.33B C F _ N.33B C F _ N.33B C F _ N.33B C F _ N.33B C F _ N.33B C F _ N.33B C F _ N.33B C F _ N.33B C F _ N.33B C F _ N.33B C F _ N.33B C F _ N.33B C otor Size 22

26 0.33 P 4 Pole 1750 rpm nominal input speed N2 rpm Speed i Ratio 2 lb.in Torque Fm lbf nit Designation lb Service Factor Overhung Load Column Entry 1-20 Blanks to be filled when entering order SERIES F SELECTION TABLES GEARED OTORS Weight of base mount unit F _ N.33B C F _ N.33B C F _ N.33B C F _ N.33B C F _ N.33B C otor Size F _ N.33B C F _ N.33B C F _ N.33B C F _ N.33B C F _ N.33B C F _ N.33B C F _ N.33B C F _ N.33B C F _ N.33B C F _ N.33B C F _ N.33B C F _ N.33B C F _ N.33B C F _ N.33B C F _ N.33B C F074310C_ N.33B C F074311C _ N.33B C F074312C_ N.33B C F074314C_ N.33B C F _ N.33B C F _ N.33B C F _ N.33B C F _ N.33B C F084310C_ N.33B C F084311C _ N.33B C F084312C_ N.33B C F084314C_ N.33B C F084316C_ N.33B C F084318C_ N.33B C F084320C_ N.33B C F084322C_ N.33B C F084325C_ N.33B C F084328C_ N.33B C F _ N.33B C F094310C_ N.33B C F094311C _ N.33B C F094312C_ N.33B C F094314C_ N.33B C F094316C_ N.33B C F094318C_ N.33B C F094320C_ N.33B C F094322C_ N.33B C F094325C_ N.33B C F094328C_ N.33B C F094332C_ N.33B C F094336C_ N.33B C F094340C_ N.33B C NOTE Other output speeds are available using 2 and 8 pole motors. Consult Application Engineering F104316C_ N.33B C F104318C_ N.33B C F104320C_ N.33B C F104322C_ N.33B C F104325C_ N.33B C F104328C_ N.33B C F104332C_ N.33B C F104336C_ N.33B C F104340C_ N.33B C F104345C_ N.33B C F104350C_ N.33B C 23

27 0.50 kw 4 Pole 1750 rpm nominal input speed N2 rpm Speed i Ratio 2 lb.in Torque Fm lbf nit Designation lb Service Factor Overhung Load Column Entry 1-20 Blanks to be filled when entering order SERIES F SELECTION TABLES GEARED OTORS Weight of base mount unit F _ N.50B C F _ N.50B C F _ N.50B C F _ N.50B C F _ N.50B C F _ N.50B C F _ N.50B C F _ N.50B C F _ N.50B C F _ N.50B C F _ N.50B C F _ N.50B C F _ N.50B C F _ N.50B C F _ N.50B C F _ N.50B C F _ N.50B C otor Size F _ N.50B C F _ N.50B C F _ N.50B C F _ N.50B C F _ N.50B C F _ N.50B C F _ N.50B C F _ N.50B C F _ N.50B C F _ N.50B C F _ N.50B C F _ N.50B C F _ N.50B C F _ N.50B C F _ N.50B C F _ N.50B C F _ N.50B C F _ N.50B C F _ N.50B C F _ N.50B C F _ N.50B C F _ N.50B C F _ N.50B C F _ N.50B C F _ N.50B C F _ N.50B C F _ N.50B C F _ N.50B C F _ N.50B C F _ N.50B C F _ N.50B C F _ N.50B C F _ N.50B C F _ N.50B C NOTE Other output speeds are available using 2 and 8 pole motors. Consult Application Engineering F _ N.50B C F _ N.50B C F _ N.50B C F _ N.50B C F _ N.50B C F _ N.50B C F _ N.50B C F _ N.50B C F _ N.50B C F _ N.50B C F _ N.50B C 24

28 0.50 P 4 Pole 1750 rpm nominal input speed N2 rpm Speed i Ratio 2 lb.in Torque Fm lbf nit Designation lb Service Factor Overhung Load Column Entry 1-20 Blanks to be filled when entering order SERIES F SELECTION TABLES GEARED OTORS Weight of base mount unit F _ N.50B C F _ N.50B C F _ N.50B C F _ N.50B C F _ N.50B C F _ N.50B C F _ N.50B C F _ N.50B C otor Size F _ N.50B C F _ N.50B C F _ N.50B C F _ N.50B C F _ N.50B C F _ N.50B C F _ N.50B C F _ N.50B C F _ N.50B C F _ N.50B C F _ N.50B C F _ N.50B C F _ N.50B C F _ N.50B C F _ N.50B C F _ N.50B C F074310C_ N.50B C F _ N.50B C F _ N.50B C F _ N.50B C F _ N.50B C F _ N.50B C F _ N.50B C F _ N.50B C F084310C_ N.50B C F084311C _ N.50B C F084312C_ N.50B C F084314C_ N.50B C F084316C_ N.50B C F084318C_ N.50B C F084320C_ N.50B C F _ N.50B C F _ N.50B C F _ N.50B C F _ N.50B C F _ N.50B C F094310C_ N.50B C F094311C _ N.50B C F094312C_ N.50B C F094314C_ N.50B C F094316C_ N.50B C F094318C_ N.50B C F094320C_ N.50B C F094322C_ N.50B C F094325C_ N.50B C F094328C_ N.50B C NOTE Other output speeds are available using 2 and 8 pole motors. Consult Application Engineering F104311C _ N.50B C F104312C_ N.50B C F104314C_ N.50B C F104316C_ N.50B C F104318C_ N.50B C F104320C_ N.50B C F104322C_ N.50B C F104325C_ N.50B C F104328C_ N.50B C F104332C_ N.50B C F104336C_ N.50B C F104340C_ N.50B C F104345C_ N.50B C 25

29 0.75 P 4 Pole 1750 rpm nominal input speed N2 rpm Speed i Ratio 2 lb.in Torque Fm lbf nit Designation lb Service Factor Overhung Load Column Entry 1-20 Blanks to be filled when entering order SERIES F SELECTION TABLES GEARED OTORS Weight of base mount unit F _ N.75B C F _ N.75B C F _ N.75B C F _ N.75B C F _ N.75B C F _ N.75B C F _ N.75B C F _ N.75B C F _ N.75B C F _ N.75B C F _ N.75B C F _ N.75B C F _ N.75B C F _ N.75B C F _ N.75B C otor Size F _ N.75B C F _ N.75B C F _ N.75B C F _ N.75B C F _ N.75B C F _ N.75B C F _ N.75B C F _ N.75B C F _ N.75B C F _ N.75B C F _ N.75B C F _ N.75B C F _ N.75B C F _ N.75B C F _ N.75B C F _ N.75B C F _ N.75B C F _ N.75B C F _ N.75B C F _ N.75B C F _ N.75B C F _ N.75B C F _ N.75B C F _ N.75B C F _ N.75B C F _ N.75B C F _ N.75B C F _ N.75B C F _ N.75B C F _ N.75B C F _ N.75B C F _ N.75B C F _ N.75B C F _ N.75B C F _ N.75B C F _ N.75B C F _ N.75B C F _ N.75B C F _ N.75B C F _ N.75B C F _ N.75B C F _ N.75B C F _ N.75B C NOTE Other output speeds are available using 2 and 8 pole motors. Consult Application Engineering F _ N.75B C F _ N.75B C F _ N.75B C 26

30 0.75 P 4 Pole 1750 rpm nominal input speed N2 rpm Speed i Ratio 2 lb.in Torque Fm lbf nit Designation lb Service Factor Overhung Load Column Entry 1-20 Blanks to be filled when entering order SERIES F SELECTION TABLES GEARED OTORS Weight of base mount unit F _ N.75B C F _ N.75B C F _ N.75B C F _ N.75B C F _ N.75B C F _ N.75B C F _ N.75B C F _ N.75B C F _ N.75B C F _ N.75B C otor Size F _ N.75B C F _ N.75B C F _ N.75B C F _ N.75B C F _ N.75B C F _ N.75B C F _ N.75B C F _ N.75B C F _ N.75B C F _ N.75B C F _ N.75B C F _ N.75B C F _ N.75B C F _ N.75B C F _ N.75B C F _ N.75B C F _ N.75B C F _ N.75B C F _ N.75B C F _ N.75B C F _ N.75B C F _ N.75B C F _ N.75B C F _ N.75B C F084310C_ N.75B C F084311C _ N.75B C F084312C_ N.75B C F _ N.75B C F _ N.75B C F _ N.75B C F _ N.75B C F _ N.75B C F _ N.75B C F _ N.75B C F _ N.75B C F094310C_ N.75B C F094311C _ N.75B C F094312C_ N.75B C F094314C_ N.75B C F094316C_ N.75B C F094318C_ N.75B C NOTE Other output speeds are available using 2 and 8 pole motors. Consult Application Engineering F _ N.75B C F _ N.75B C F _ N.75B C F104310C_ N.75B C F104311C _ N.75B C F104312C_ N.75B C F104314C_ N.75B C F104316C_ N.75B C F104318C_ N.75B C F104320C_ N.75B C F104322C_ N.75B C F104325C_ N.75B C F104328C_ N.75B C F104332C_ N.75B C 27

31 1.0 P 4 Pole 1750 rpm nominal input speed NOTE Other output speeds are available using 2 and 8 pole motors. Consult Application Engineering N2 rpm Speed i Ratio 2 lb.in Torque Fm lbf nit Designation lb Service Factor Overhung Load Column Entry 1-20 Blanks to be filled when entering order SERIES F SELECTION TABLES GEARED OTORS Weight of base mount unit F _ N 1.0B TC F _ N 1.0B TC F _ N 1.0B TC F _ N 1.0B TC F _ N 1.0B TC F _ N 1.0B TC F _ N 1.0B TC F _ N 1.0B TC F _ N 1.0B TC F _ N 1.0B TC F _ N 1.0B TC F _ N 1.0B TC F _ N 1.0B TC F _ N 1.0B TC F _ N 1.0B TC F _ N 1.0B TC F _ N 1.0B TC F _ N 1.0B TC F _ N 1.0B TC F _ N 1.0B TC F _ N 1.0B TC F _ N 1.0B TC F _ N 1.0B TC F _ N 1.0B TC F _ N 1.0B TC F _ N 1.0B TC F _ N 1.0B TC F _ N 1.0B TC F _ N 1.0B TC F _ N 1.0B TC F _ N 1.0B TC F _ N 1.0B TC F _ N 1.0B TC F _ N 1.0B TC F _ N 1.0B TC F _ N 1.0B TC F _ N 1.0B TC F _ N 1.0B TC F _ N 1.0B TC F _ N 1.0B TC F _ N 1.0B TC F _ N 1.0B TC F _ N 1.0B TC F _ N 1.0B TC F _ N 1.0B TC F _ N 1.0B TC F _ N 1.0B TC F _ N 1.0B TC F _ N 1.0B TC F _ N 1.0B TC F _ N 1.0B TC F _ N 1.0B TC F _ N 1.0B TC F _ N 1.0B TC F _ N 1.0B TC F _ N 1.0B TC F _ N 1.0B TC F _ N 1.0B TC F _ N 1.0B TC F _ N 1.0B TC F _ N 1.0B TC F _ N 1.0B TC F _ N 1.0B TC F _ N 1.0B TC F _ N 1.0B TC F _ N 1.0B TC F _ N 1.0B TC otor Size 28

32 1.0 P 4 Pole 1750 rpm nominal input speed N2 rpm Speed i Ratio 2 lb.in Torque Fm lbf nit Designation lb Service Factor Overhung Load Column Entry 1-20 Blanks to be filled when entering order SERIES F SELECTION TABLES GEARED OTORS Weight of base mount unit F _ N 1.0B TC F _ N 1.0B TC F _ N 1.0B TC F _ N 1.0B TC F _ N 1.0B TC F _ N 1.0B TC F _ N 1.0B TC F _ N 1.0B TC F _ N 1.0B TC F _ N 1.0B TC F _ N 1.0B TC otor Size F _ N 1.0B TC F _ N 1.0B TC F _ N 1.0B TC F _ N 1.0B TC F _ N 1.0B TC F _ N 1.0B TC F _ N 1.0B TC F _ N 1.0B TC F _ N 1.0B TC F _ N 1.0B TC F _ N 1.0B TC F _ N 1.0B TC F _ N 1.0B TC F _ N 1.0B TC F _ N 1.0B TC F _ N 1.0B TC F _ N 1.0B TC F _ N 1.0B TC F _ N 1.0B TC F _ N 1.0B TC F _ N 1.0B TC F _ N 1.0B TC F _ N 1.0B TC F _ N 1.0B TC F _ N 1.0B TC F _ N 1.0B TC F _ N 1.0B TC F094310C_ N 1.0B TC F094311C _ N 1.0B TC F094312C_ N 1.0B TC F _ N 1.0B TC F _ N 1.0B TC F _ N 1.0B TC F _ N 1.0B TC F _ N 1.0B TC F104310C_ N 1.0B TC F104311C _ N 1.0B TC F104312C_ N 1.0B TC F104314C_ N 1.0B TC F104316C_ N 1.0B TC F104318C_ N 1.0B TC F104320C_ N 1.0B TC F104322C_ N 1.0B TC F104325C_ N 1.0B TC NOTE Other output speeds are available using 2 and 8 pole motors. Consult Application Engineering 29

33 1.5 P 4 Pole 1750 rpm nominal input speed N2 rpm Speed i Ratio 2 lb.in Torque Fm lbf nit Designation lb Service Factor Overhung Load Column Entry 1-20 Blanks to be filled when entering order SERIES F SELECTION TABLES GEARED OTORS Weight of base mount unit F _ N 1.5B TC F _ N 1.5B TC F _ N 1.5B TC F _ N 1.5B TC F _ N 1.5B TC F _ N 1.5B TC F _ N 1.5B TC F _ N 1.5B TC otor Size F _ N 1.5B TC F _ N 1.5B TC F _ N 1.5B TC F _ N 1.5B TC F _ N 1.5B TC F _ N 1.5B TC F _ N 1.5B TC F _ N 1.5B TC F _ N 1.5B TC F _ N 1.5B TC F _ N 1.5B TC F _ N 1.5B TC F _ N 1.5B TC F _ N 1.5B TC F _ N 1.5B TC F _ N 1.5B TC F _ N 1.5B TC F _ N 1.5B TC F _ N 1.5B TC F _ N 1.5B TC F _ N 1.5B TC F _ N 1.5B TC F _ N 1.5B TC F _ N 1.5B TC F _ N 1.5B TC F _ N 1.5B TC F _ N 1.5B TC F _ N 1.5B TC F _ N 1.5B TC F _ N 1.5B TC F _ N 1.5B TC F _ N 1.5B TC F _ N 1.5B TC F _ N 1.5B TC F _ N 1.5B TC F _ N 1.5B TC F _ N 1.5B TC F _ N 1.5B TC F _ N 1.5B TC F _ N 1.5B TC F _ N 1.5B TC F _ N 1.5B TC F _ N 1.5B TC F _ N 1.5B TC F _ N 1.5B TC F _ N 1.5B TC F _ N 1.5B TC NOTE F _ N 1.5B TC F _ N 1.5B TC F _ N 1.5B TC F _ N 1.5B TC F _ N 1.5B TC Other output speeds are available using 2 and 8 pole motors. Consult Application Engineering 30

34 1.5 P 4 Pole 1750 rpm nominal input speed N2 rpm Speed i Ratio 2 lb.in Torque Fm lbf nit Designation lb Service Factor Overhung Load Column Entry 1-20 Blanks to be filled when entering order SERIES F SELECTION TABLES GEARED OTORS Weight of base mount unit F _ N 1.5B TC F _ N 1.5B TC F _ N 1.5B TC otor Size F _ N 1.5B TC F _ N 1.5B TC F _ N 1.5B TC F _ N 1.5B TC F _ N 1.5B TC F _ N 1.5B TC F _ N 1.5B TC F _ N 1.5B TC F _ N 1.5B TC F _ N 1.5B TC F _ N 1.5B TC F _ N 1.5B TC F _ N 1.5B TC F _ N 1.5B TC F _ N 1.5B TC F _ N 1.5B TC F _ N 1.5B TC F _ N 1.5B TC F _ N 1.5B TC F _ N 1.5B TC F _ N 1.5B TC F _ N 1.5B TC F _ N 1.5B TC F _ N 1.5B TC F _ N 1.5B TC F _ N 1.5B TC F _ N 1.5B TC F _ N 1.5B TC F _ N 1.5B TC F _ N 1.5B TC F _ N 1.5B TC F _ N 1.5B TC F _ N 1.5B TC F _ N 1.5B TC F _ N 1.5B TC F _ N 1.5B TC F _ N 1.5B TC F _ N 1.5B TC F _ N 1.5B TC F _ N 1.5B TC F _ N 1.5B TC F _ N 1.5B TC F _ N 1.5B TC F _ N 1.5B TC F _ N 1.5B TC F104310C_ N 1.5B TC F104311C _ N 1.5B TC F104312C_ N 1.5B TC F104314C_ N 1.5B TC F104316C_ N 1.5B TC NOTE Other output speeds are available using 2 and 8 pole motors. Consult Application Engineering 31

35 2.0 P 4 Pole 1750 rpm nominal input speed N2 rpm Speed i Ratio 2 lb.in Torque Fm lbf nit Designation lb Service Factor Overhung Load Column Entry 1-20 Blanks to be filled when entering order SERIES F SELECTION TABLES GEARED OTORS Weight of base mount unit F _ N 2.0B TC F _ N 2.0B TC F _ N 2.0B TC F _ N 2.0B TC F _ N 2.0B TC F _ N 2.0B TC otor Size F _ N 2.0B TC F _ N 2.0B TC F _ N 2.0B TC F _ N 2.0B TC F _ N 2.0B TC F _ N 2.0B TC F _ N 2.0B TC F _ N 2.0B TC F _ N 2.0B TC F _ N 2.0B TC F _ N 2.0B TC F _ N 2.0B TC F _ N 2.0B TC F _ N 2.0B TC F _ N 2.0B TC F _ N 2.0B TC F _ N 2.0B TC F _ N 2.0B TC F _ N 2.0B TC F _ N 2.0B TC F _ N 2.0B TC F _ N 2.0B TC F _ N 2.0B TC F _ N 2.0B TC F _ N 2.0B TC F _ N 2.0B TC F _ N 2.0B TC F _ N 2.0B TC F _ N 2.0B TC F _ N 2.0B TC F _ N 2.0B TC F _ N 2.0B TC F _ N 2.0B TC F _ N 2.0B TC F _ N 2.0B TC F _ N 2.0B TC F _ N 2.0B TC F _ N 2.0B TC F _ N 2.0B TC F _ N 2.0B TC F _ N 2.0B TC F _ N 2.0B TC F _ N 2.0B TC F _ N 2.0B TC F _ N 2.0B TC F _ N 2.0B TC F _ N 2.0B TC F _ N 2.0B TC F _ N 2.0B TC F _ N 2.0B TC NOTE F _ N 2.0B TC F _ N 2.0B TC F _ N 2.0B TC F _ N 2.0B TC F _ N 2.0B TC Other output speeds are available using 2 and 8 pole motors. Consult Application Engineering 32

36 2.0 P 4 Pole 1750 rpm nominal input speed N2 rpm Speed i Ratio 2 lb.in Torque Fm lbf nit Designation lb Service Factor Overhung Load Column Entry 1-20 Blanks to be filled when entering order SERIES F SELECTION TABLES GEARED OTORS Weight of base mount unit F _ N 2.0B TC F _ N 2.0B TC F _ N 2.0B TC F _ N 2.0B TC F _ N 2.0B TC F _ N 2.0B TC F _ N 2.0B TC F _ N 2.0B TC F _ N 2.0B TC otor Size F _ N 2.0B TC F _ N 2.0B TC F _ N 2.0B TC F _ N 2.0B TC F _ N 2.0B TC F _ N 2.0B TC F _ N 2.0B TC F _ N 2.0B TC F _ N 2.0B TC F _ N 2.0B TC F _ N 2.0B TC F _ N 2.0B TC F _ N 2.0B TC F _ N 2.0B TC F _ N 2.0B TC F _ N 2.0B TC F _ N 2.0B TC F _ N 2.0B TC F _ N 2.0B TC F _ N 2.0B TC F _ N 2.0B TC F _ N 2.0B TC F _ N 2.0B TC F _ N 2.0B TC F _ N 2.0B TC F _ N 2.0B TC F _ N 2.0B TC F _ N 2.0B TC F _ N 2.0B TC F _ N 2.0B TC F _ N 2.0B TC F _ N 2.0B TC F _ N 2.0B TC F _ N 2.0B TC F _ N 2.0B TC F104310C_ N 2.0B TC F104311C _ N 2.0B TC F104312C_ N 2.0B TC NOTE Other output speeds are available using 2 and 8 pole motors. Consult Application Engineering 33

37 3.0 P 4 Pole 1750 rpm nominal input speed N2 rpm Speed i Ratio 2 lb.in Torque Fm lbf nit Designation lb Service Factor Overhung Load Column Entry 1-20 Blanks to be filled when entering order SERIES F SELECTION TABLES GEARED OTORS Weight of base mount unit F _ N 3.0B TC F _ N 3.0B TC F _ N 3.0B TC F _ N 3.0B TC F _ N 3.0B TC F _ N 3.0B TC otor Size F _ N 3.0B TC F _ N 3.0B TC F _ N 3.0B TC F _ N 3.0B TC F _ N 3.0B TC F _ N 3.0B TC F _ N 3.0B TC F _ N 3.0B TC F _ N 3.0B TC F _ N 3.0B TC F _ N 3.0B TC F _ N 3.0B TC F _ N 3.0B TC F _ N 3.0B TC F _ N 3.0B TC F _ N 3.0B TC F _ N 3.0B TC F _ N 3.0B TC F _ N 3.0B TC F _ N 3.0B TC F _ N 3.0B TC F _ N 3.0B TC F _ N 3.0B TC F _ N 3.0B TC F _ N 3.0B TC F _ N 3.0B TC F _ N 3.0B TC F _ N 3.0B TC F _ N 3.0B TC F _ N 3.0B TC F _ N 3.0B TC F _ N 3.0B TC F _ N 3.0B TC F _ N 3.0B TC F _ N 3.0B TC F _ N 3.0B TC F _ N 3.0B TC F _ N 3.0B TC F _ N 3.0B TC F _ N 3.0B TC F _ N 3.0B TC F _ N 3.0B TC F _ N 3.0B TC F _ N 3.0B TC F _ N 3.0B TC F _ N 3.0B TC F _ N 3.0B TC F _ N 3.0B TC F _ N 3.0B TC F _ N 3.0B TC F _ N 3.0B TC F _ N 3.0B TC NOTE Other output speeds are available using 2 and 8 pole motors. Consult Application Engineering F _ N 3.0B TC F _ N 3.0B TC F _ N 3.0B TC F _ N 3.0B TC F _ N 3.0B TC F _ N 3.0B TC F _ N 3.0B TC F _ N 3.0B TC F _ N 3.0B TC 34

38 3.0 P 4 Pole 1750 rpm nominal input speed N2 rpm Speed i Ratio 2 lb.in Torque Fm lbf nit Designation lb Service Factor Overhung Load Column Entry 1-20 Blanks to be filled when entering order SERIES F SELECTION TABLES GEARED OTORS Weight of base mount unit F _ N 3.0B TC F _ N 3.0B TC F _ N 3.0B TC F _ N 3.0B TC F _ N 3.0B TC F _ N 3.0B TC F _ N 3.0B TC F _ N 3.0B TC F _ N 3.0B TC F _ N 3.0B TC otor Size F _ N 3.0B TC F _ N 3.0B TC F _ N 3.0B TC F _ N 3.0B TC F _ N 3.0B TC F _ N 3.0B TC F _ N 3.0B TC F _ N 3.0B TC F _ N 3.0B TC F _ N 3.0B TC F _ N 3.0B TC F _ N 3.0B TC 5.0 P 4 POLE F _ N 5.0B TC F _ N 5.0B TC F _ N 5.0B TC F _ N 5.0B TC F _ N 5.0B TC F _ N 5.0B TC F _ N 5.0B TC F _ N 5.0B TC F _ N 5.0B TC F _ N 5.0B TC F _ N 5.0B TC F _ N 5.0B TC F _ N 5.0B TC F _ N 5.0B TC F _ N 5.0B TC F _ N 5.0B TC F _ N 5.0B TC F _ N 5.0B TC F _ N 5.0B TC F _ N 5.0B TC F _ N 5.0B TC F _ N 5.0B TC F _ N 5.0B TC NOTE Other output speeds are available using 2 and 8 pole motors. Consult Application Engineering F _ N 5.0B TC F _ N 5.0B TC F _ N 5.0B TC F _ N 5.0B TC F _ N 5.0B TC F _ N 5.0B TC F _ N 5.0B TC F _ N 5.0B TC F _ N 5.0B TC F _ N 5.0B TC F _ N 5.0B TC F _ N 5.0B TC F _ N 5.0B TC F _ N 5.0B TC 35

39 5.0 P 4 Pole 1750 rpm nominal input speed N2 rpm Speed i Ratio 2 lb.in Torque Fm lbf nit Designation lb Service Factor Overhung Load Column Entry 1-20 Blanks to be filled when entering order SERIES F SELECTION TABLES GEARED OTORS Weight of base mount unit F _ N 5.0B TC F _ N 5.0B TC F _ N 5.0B TC F _ N 5.0B TC F _ N 5.0B TC F _ N 5.0B TC F _ N 5.0B TC F _ N 5.0B TC F _ N 5.0B TC F _ N 5.0B TC F _ N 5.0B TC otor Size F _ N 5.0B TC F _ N 5.0B TC F _ N 5.0B TC F _ N 5.0B TC F _ N 5.0B TC F _ N 5.0B TC F _ N 5.0B TC F _ N 5.0B TC F _ N 5.0B TC F _ N 5.0B TC F _ N 5.0B TC F _ N 5.0B TC F _ N 5.0B TC F _ N 5.0B TC F _ N 5.0B TC F _ N 5.0B TC F _ N 5.0B TC F _ N 5.0B TC F _ N 5.0B TC F _ N 5.0B TC F _ N 5.0B TC F _ N 5.0B TC F _ N 5.0B TC F _ N 5.0B TC F _ N 5.0B TC F _ N 5.0B TC F _ N 5.0B TC F _ N 5.0B TC F _ N 5.0B TC F _ N 5.0B TC F _ N 5.0B TC F _ N 5.0B TC F _ N 5.0B TC F _ N 5.0B TC F _ N 5.0B TC F _ N 5.0B TC F _ N 5.0B TC F _ N 5.0B TC F _ N 5.0B TC NOTE Other output speeds are available using 2 and 8 pole motors. Consult Application Engineering 36

40 7.5 P 4 Pole 1750 rpm nominal input speed NOTE Other output speeds are available using 2 and 8 pole motors. Consult Application Engineering N2 rpm Speed i Ratio 2 lb.in Torque Fm lbf nit Designation lb Service Factor Overhung Load Column Entry 1-20 Blanks to be filled when entering order SERIES F SELECTION TABLES GEARED OTORS Weight of base mount unit F _ N 7.5B TC F _ N 7.5B TC F _ N 7.5B TC F _ N 7.5B TC F _ N 7.5B TC F _ N 7.5B TC F _ N 7.5B TC F _ N 7.5B TC F _ N 7.5B TC F _ N 7.5B TC F _ N 7.5B TC F _ N 7.5B TC F _ N 7.5B TC F _ N 7.5B TC F _ N 7.5B TC F _ N 7.5B TC F _ N 7.5B TC F _ N 7.5B TC F _ N 7.5B TC F _ N 7.5B TC F _ N 7.5B TC F _ N 7.5B TC F _ N 7.5B TC F _ N 7.5B TC F _ N 7.5B TC F _ N 7.5B TC F _ N 7.5B TC F _ N 7.5B TC F _ N 7.5B TC F _ N 7.5B TC F _ N 7.5B TC F _ N 7.5B TC F _ N 7.5B TC F _ N 7.5B TC F _ N 7.5B TC F _ N 7.5B TC F _ N 7.5B TC F _ N 7.5B TC F _ N 7.5B TC F _ N 7.5B TC F _ N 7.5B TC F _ N 7.5B TC F _ N 7.5B TC F _ N 7.5B TC F _ N 7.5B TC F _ N 7.5B TC F _ N 7.5B TC F _ N 7.5B TC F _ N 7.5B TC F _ N 7.5B TC F _ N 7.5B TC F _ N 7.5B TC F _ N 7.5B TC F _ N 7.5B TC F _ N 7.5B TC F _ N 7.5B TC F _ N 7.5B TC F _ N 7.5B TC F _ N 7.5B TC F _ N 7.5B TC F _ N 7.5B TC F _ N 7.5B TC F _ N 7.5B TC F _ N 7.5B TC F _ N 7.5B TC F _ N 7.5B TC F _ N 7.5B TC F _ N 7.5B TC otor Size 37

41 10 P 4 Pole 1750 rpm nominal input speed N2 rpm Speed i Ratio 2 lb.in Torque Fm lbf nit Designation lb Service Factor Overhung Load Column Entry 1-20 Blanks to be filled when entering order SERIES F SELECTION TABLES GEARED OTORS Weight of base mount unit F _ N 10.B TC F _ N 10.B TC F _ N 10.B TC F _ N 10.B TC F _ N 10.B TC otor Size F _ N 10.B TC F _ N 10.B TC F _ N 10.B TC F _ N 10.B TC F _ N 10.B TC F _ N 10.B TC F _ N 10.B TC F _ N 10.B TC F _ N 10.B TC F _ N 10.B TC F _ N 10.B TC F _ N 10.B TC F _ N 10.B TC F _ N 10.B TC F _ N 10.B TC F _ N 10.B TC F _ N 10.B TC F _ N 10.B TC F _ N 10.B TC F _ N 10.B TC F _ N 10.B TC F _ N 10.B TC F _ N 10.B TC F _ N 10.B TC F _ N 10.B TC F _ N 10.B TC F _ N 10.B TC F _ N 10.B TC F _ N 10.B TC F _ N 10.B TC F _ N 10.B TC F _ N 10.B TC F _ N 10.B TC F _ N 10.B TC F _ N 10.B TC F _ N 10.B TC F _ N 10.B TC F _ N 10.B TC F _ N 10.B TC F _ N 10.B TC F _ N 10.B TC F _ N 10.B TC F _ N 10.B TC F _ N 10.B TC F _ N 10.B TC F _ N 10.B TC F _ N 10.B TC F _ N 10.B TC F _ N 10.B TC F _ N 10.B TC F _ N 10.B TC F _ N 10.B TC F _ N 10.B TC NOTE Other output speeds are available using 2 and 8 pole motors. Consult Application Engineering F _ N 10.B TC F _ N 10.B TC F _ N 10.B TC F _ N 10.B TC F _ N 10.B TC F _ N 10.B TC F _ N 10.B TC 38

42 15 P 4 Pole 1750 rpm nominal input speed N2 rpm Speed i Ratio 2 lb.in Torque Fm lbf nit Designation lb Service Factor Overhung Load Column Entry 1-20 Blanks to be filled when entering order SERIES F SELECTION TABLES GEARED OTORS Weight of base mount unit F _ N 15.B TC F _ N 15.B TC F _ N 15.B TC F _ N 15.B TC F _ N 15.B TC F _ N 15.B TC otor Size F _ N 15.B TC F _ N 15.B TC F _ N 15.B TC F _ N 15.B TC F _ N 15.B TC F _ N 15.B TC F _ N 15.B TC F _ N 15.B TC F _ N 15.B TC F _ N 15.B TC F _ N 15.B TC F _ N 15.B TC F _ N 15.B TC F _ N 15.B TC F _ N 15.B TC F _ N 15.B TC F _ N 15.B TC F _ N 15.B TC F _ N 15.B TC F _ N 15.B TC F _ N 15.B TC F _ N 15.B TC F _ N 15.B TC F _ N 15.B TC F _ N 15.B TC F _ N 15.B TC F _ N 15.B TC F _ N 15.B TC F _ N 15.B TC F _ N 15.B TC F _ N 15.B TC F _ N 15.B TC F _ N 15.B TC F _ N 15.B TC F _ N 15.B TC F _ N 15.B TC F _ N 15.B TC F _ N 15.B TC F _ N 15.B TC F _ N 15.B TC F _ N 15.B TC F _ N 15.B TC NOTE Other output speeds are available using 2 and 8 pole motors. Consult Application Engineering 39

43 20 P 4 Pole 1750 rpm nominal input speed N2 rpm Speed i Ratio 2 lb.in Torque Fm lbf nit Designation lb Service Factor Overhung Load Column Entry 1-20 Blanks to be filled when entering order SERIES F SELECTION TABLES GEARED OTORS Weight of base mount unit F _ N 20.B TC F _ N 20.B TC F _ N 20.B TC F _ N 20.B TC F _ N 20.B TC F _ N 20.B TC otor Size F _ N 20.B TC F _ N 20.B TC F _ N 20.B TC F _ N 20.B TC F _ N 20.B TC F _ N 20.B TC F _ N 20.B TC F _ N 20.B TC F _ N 20.B TC F _ N 20.B TC F _ N 20.B TC F _ N 20.B TC F _ N 20.B TC F _ N 20.B TC F _ N 20.B TC F _ N 20.B TC F _ N 20.B TC F _ N 20.B TC F _ N 20.B TC F _ N 20.B TC F _ N 20.B TC F _ N 20.B TC F _ N 20.B TC F _ N 20.B TC F _ N 20.B TC F _ N 20.B TC F _ N 20.B TC F _ N 20.B TC F _ N 20.B TC F _ N 20.B TC F _ N 20.B TC F _ N 20.B TC F _ N 20.B TC F _ N 20.B TC F _ N 20.B TC F _ N 20.B TC F _ N 20.B TC F _ N 20.B TC F _ N 20.B TC NOTE Other output speeds are available using 2 and 8 pole motors. Consult Application Engineering 40

44 25 P 4 Pole 1750 rpm nominal input speed N2 rpm Speed i Ratio 2 lb.in Torque Fm lbf nit Designation lb Service Factor Overhung Load Column Entry 1-20 Blanks to be filled when entering order SERIES F SELECTION TABLES GEARED OTORS Weight of base mount unit F _ N 25.B TC F _ N 25.B TC F _ N 25.B TC F _ N 25.B TC F _ N 25.B TC F _ N 25.B TC F _ N 25.B TC F _ N 25.B TC F _ N 25.B TC F _ N 25.B TC F _ N 25.B TC F _ N 25.B TC F _ N 25.B TC otor Size F _ N 25.B TC F _ N 25.B TC F _ N 25.B TC F _ N 25.B TC F _ N 25.B TC F _ N 25.B TC F _ N 25.B TC F _ N 25.B TC F _ N 25.B TC F _ N 25.B TC F _ N 25.B TC F _ N 25.B TC F _ N 25.B TC 30 P 4 POLE F _ N 30.B TC F _ N 30.B TC F _ N 30.B TC F _ N 30.B TC F _ N 30.B TC F _ N 30.B TC F _ N 30.B TC F _ N 30.B TC F _ N 30.B TC F _ N 30.B TC F _ N 30.B TC F _ N 30.B TC F _ N 30.B TC F _ N 30.B TC F _ N 30.B TC F _ N 30.B TC F _ N 30.B TC F _ N 30.B TC F _ N 30.B TC F _ N 30.B TC F _ N 30.B TC F _ N 30.B TC F _ N 30.B TC F _ N 30.B TC NOTE Other output speeds are available using 2 and 8 pole motors. Consult Application Engineering 41

45 40 P 4 Pole 1750 rpm nominal input speed N2 rpm Speed i Ratio 2 lb.in Torque Fm lbf nit Designation lb Service Factor Overhung Load Column Entry 1-20 Blanks to be filled when entering order SERIES F SELECTION TABLES GEARED OTORS Weight of base mount unit F _ N 40.B TC F _ N 40.B TC F _ N 40.B TC F _ N 40.B TC F _ N 40.B TC F _ N 40.B TC F _ N 40.B TC F _ N 40.B TC F _ N 40.B TC F _ N 40.B TC F _ N 40.B TC otor Size F _ N 40.B TC F _ N 40.B TC F _ N 40.B TC F _ N 40.B TC F _ N 40.B TC F _ N 40.B TC F _ N 40.B TC F _ N 40.B TC F _ N 40.B TC F _ N 40.B TC F _ N 40.B TC F _ N 40.B TC 50 P 4 POLE F _ N 50.B TC F _ N 50.B TC F _ N 50.B TC F _ N 50.B TC F _ N 50.B TC F _ N 50.B TC F _ N 50.B TC F _ N 50.B TC F _ N 50.B TC F _ N 50.B TC F _ N 50.B TC F _ N 50.B TC F _ N 50.B TC F _ N 50.B TC F _ N 50.B TC F _ N 50.B TC F _ N 50.B TC F _ N 50.B TC F _ N 50.B TC F _ N 50.B TC F _ N 50.B TC F _ N 50.B TC F _ N 50.B TC NOTE Other output speeds are available using 2 and 8 pole motors. Consult Application Engineering 42

46 DIENSIONS DOBLE / TRIPLE REDCTION a10 k1 k0 C4 O S4 O g t i2 f4 N2 h1 a9 P3 N3 N1 N4 N V1 O7 m2 v4 T m3 O D Od u L12 L m m1 m a9 a10 C4 f4 h1 N N1 N2 N3 N4 O7 P3 S4 V1 F F F F F F F F F F F F F F F F F F D m m1 m2 m3 T v4 d i2 L L12 t u F F / NF x F F / NF x / F F / NF x / F F / NF x / F F / NF x / F F / NF x / F F / NF x / F F / NF x / F F / NF x / F0223 F0233 F0323 F0333 F0423 F0433 F0523 F0533 F0623 F0633 F0723 F0733 F0823 F0833 F0923 F0933 F1023 F1033 otor k0 g k1 k1 k1 k1 k1 k1 k1 k1 k1 k1 k1 k1 k1 k1 k1 k1 k1 k1 56C TC TC TC TC TC TC

47 DIENSIONS QADRPLE REDCTION k1 k0 C4 a10 O S4 * t u i2 f4 N2 h1 v2 v3 O g a9 P3 L12 L N3 N1 N4 N v1 O7 m2 v4 T m3 O D m m m1 a9 a10 C4 f4 h1 N N1 N2 N3 N4 O7 P3 S4 v1 v2 v3 F F F F F F F F D m m1 m2 m3 T v4 d i2 L L12 t u F / NF x / F / NF x / F / NF x / F / NF x / F / NF x / F / NF x / F / NF x / F / NF x / F0343 F0443 F0543 F0643 F0743 F0843 F0943 F1043 otor k0 g k1 k1 k1 k1 k1 k1 k1 k1 56C TC TC TC TC

48 Kh SERIES F OTORISED BACKSTOP ODLE otorised backstop modules can be fitted between the gear unit and motor. The backstop device incorporates high quality centrifugal lift off sprags which are wear free above the lift off speed (n min). To ensure correct operation motor speed must exceed lift off speed. Suitable for ambient temperature -40 o F to o F Og6 NEA C Flange When a backstop module is fitted dimension Kh should be added to the overall length of the geared motor assembly. Warning Removal of motor or backstop will release the drive. Ensure all driven machinery is secure prior to any maintenance work. Size Lift off Speed ( n min) (rev/min) Rated Locking Torque ( T max ) (at motor) (Nm) øg6 Kh IEC B5 Flange Size Lift off Speed ( n min) (rev/min) Rated Locking Torque ( T max ) (at motor) (Nm) øg6 Kh 182TC / 184TC TC / 215TC TC / 256TC TC / 286TC TC / 326TC Rotation of outputshaft must be specified when ordering as viewed from the outputshaft end (as shown in the diagram) CW - Free Rotation - Clockwise Locked - Anticlockwise AC - Free Rotation - Anticlockwise Locked - Clockwise CW 45

49 OPTIONS Shaft ounted with Torque Bush Shaft With Feet Shaft with Flange Taper Release Bushing (TR) nit with Shrink Disk Screw Conveyor 46

50 REDCER SERIES F 47

51 aximum Permissible Overhung Loads SERIES F OVERNG & AXIAL LOADS ON SAFTS When a sprocket, gear etc. is mounted on the shaft a calculation, as below, must be made to determine the overhung load (P) on the shaft, and the results compared to the maximum permissible overhung loads tabulated (Fra or Frb). Overhung loads can be reduced by increasing the diameter of the sprocket, gear, etc. If the maximum permissible overhung load is exceeded, the sprocket, gear, etc. should be mounted on a separate shaft, flexibly coupled and supported in its own bearings, or the gear unit shaft could be extended to run in an outboard bearing. Permissible overhung loads vary according to the direction of rotation. The values tabulated are for the most unfavourable direction with the unit transmitting full rated power, with load P applied midway along the shaft extension. ence they may be increased for a more favourable direction of rotation, or if the power transmitted is less than the rated capacity of the gear unit - consult our Application Engineers for details. The position of the sprocket, gear etc should be as close to the gear unit case as possible, should the position of the outputshaft load P vary from midway along the shaft extension, the allowable tabulated loads Fra shall be adjusted by Factor FL (see details below) All units will accept 100% momentary overload on stated capacities Overhung Load (lbf) P = P x 630,000 x K N x R Where P = equivalent overhung load (lbf) P = power transmitted by the shaft (P) N = speed of shaft ( rpm ) R = pitch radius of sprocket, etc. ( inches) K = factor Note: 1 lbf = 4.45 Newton Frb B The applied load P should not exceed tabulated values Fra and Frb Overhung ember K (factor) Chain sprocket* 1.00 Spur or helical pinion 1.25 Vee belt sheave 1.50 Flat belt pulley 2.00 * If multistrand chain drives are equally loaded and the outer strand is further than dimension A output or B input, refer to Application Engineering. Shaft Overhung Loads (Fra) Consult the Gear nit Ratings Tables for value Fra The Fra values tabulated assume load P is applied midway along the shaft extension (dimension A in the table below) If load P is applied in a different position the tabulated value Fra shall be adjusted by the following formula: Fra x FL FL = C x D (D+Lx) Lx = Distance (inches) to the applied load P from the shaft shoulder A Fra Size A (inches) Red n Stages B (inches) Constants F02 n/a 2 & n/a n/a C D F , 3 & F , 3, & F , 3, & Inputshaft Overhung Loads, Frb (lb) 1750 rpm Two, Three and Four Stage nits F02 F03 F04 F05 F06 F07 F08 F09 F10 2 stage stage stage Axial Thrust Capacities (lbf) No check or calculation is required if the axial thrust load (FA) towards or away from the unit is under 50% of the permissible overhung load. If the axial thrust considerably exceeds these values or if there is a combination of axial thrust loads and overhung loads please contact our Application Engineers. F , 3, & F F F F , 4 &

52 Thermal Ratings P Thermal ratings are a measure of the units ability to dissipate heat, if they are exceeded the lubricant may break down resulting in premature gear failure. Thermal rating are based on an ambient temperature of 77 o F, where units are to operate in other ambient temperatures thermal ratings must be adjusted by the following factors Ambient Temp odifing Factor Ft TERAL POWER RATING -4ºF 14ºF 32ºF 50ºF 68ºF 77ºF 95ºF 104ºF 113ºF 122ºF nits without additional cooling n1 (rpm) 3500 in ( :1) F0223 F0323 F0423 F0523 F0623 F0723 F0823 F0923 F n1 (rpm) 3500 in ( :1) F0233 F0333 F0433 F0533 F0633 F0733 F0833 F0933 F nits with fan cooling n1 (rpm) 3500 in ( :1) F0723 F0823 F0923 F

53 RATINGS Key: Pm= Input Power (P) 2= Torque (lb.in) i= Exact Ratio n2= Speed (rpm) Fra = Overhung load (lbf) n1 = 1750 n1 = 1160 n1 = 3500 n1 = 875 in i n2 2 Pm Fra n2 2 Pm Fra n2 2 Pm Fra n2 2 Pm Fra F F F F Note: Input power Pm may exceed thermal power rating 50

54 RATINGS Key: Pm= Input Power (P) 2= Torque (lb.in) i= Exact Ratio n2= Speed (rpm) Fra = Overhung load (lbf) n1 = 1750 n1 = 1160 n1 = 3500 n1 = 875 in i n2 2 Pm Fra n2 2 Pm Fra n2 2 Pm Fra n2 2 Pm Fra F c c c c c c c c c c c c F F F C C C C C C C C C C C C C C C Note: Input power Pm may exceed thermal power rating 51

55 RATINGS Key: Pm= Input Power (P) 2= Torque (lb.in) i= Exact Ratio n2= Speed (rpm) Fra = Overhung load (lbf) n1 = 1750 n1 = 1160 n1 = 3500 n1 = 875 in i n2 2 Pm Fra n2 2 Pm Fra n2 2 Pm Fra n2 2 Pm Fra F F F C C C C C C C C C C C C C C F Note: Input power Pm may exceed thermal power rating 52

56 RATINGS Key: Pm= Input Power (P) 2= Torque (lb.in) i= Exact Ratio n2= Speed (rpm) Fra = Overhung load (lbf) n1 = 1750 n1 = 1160 n1 = 3500 n1 = 875 in i n2 2 Pm Fra n2 2 Pm Fra n2 2 Pm Fra n2 2 Pm Fra F F C C C C C C C C C C C C C F F Note: Input power Pm may exceed thermal power rating 53

57 RATINGS Key: Pm= Input Power (P) 2= Torque (lb.in) i= Exact Ratio n2= Speed (rpm) Fra = Overhung load (lbf) n1 = 1750 n1 = 1160 n1 = 3500 n1 = 875 in i n2 2 Pm Fra n2 2 Pm Fra n2 2 Pm Fra n2 2 Pm Fra F C C C C C C C C C C C C C C C F F F C C C C C C C C C C C C C C C Note: Input power Pm may exceed thermal power rating 54

58 RATINGS Key: Pm= Input Power (P) 2= Torque (lb.in) i= Exact Ratio n2= Speed (rpm) Fra = Overhung load (lbf) n1 = 1750 n1 = 1160 n1 = 3500 n1 = 875 in i n2 2 Pm Fra n2 2 Pm Fra n2 2 Pm Fra n2 2 Pm Fra F F F C C C C C C C C C C C C C C C Note: Input power Pm may exceed thermal power rating 55

59 RATINGS Key: Pm= Input Power (P) 2= Torque (lb.in) i= Exact Ratio n2= Speed (rpm) Fra = Overhung load (lbf) n1 = 1750 n1 = 1160 n1 = 3500 n1 = 875 in i n2 2 Pm Fra n2 2 Pm Fra n2 2 Pm Fra n2 2 Pm Fra F F F C C C C C C C C C C C C C C C Note: Input power Pm may exceed thermal power rating 56

60 DIENSIONS DOBLE / TRIPLE REDCTION k C4 a10 L1 O S4 N2 h1 a9 P3 N1 v1 N4 N O7 m2 v4 T m3 O D O d1 t i2 f4 t1 L14 Od u L12 Od1 u1 L N3 m m m1 a9 a10 C4 f4 h1 N N1 N2 N3 N4 O7 P3 S4 v1 F F F F F F F F F F F F F F F F F F k d1 L1 L14 t1 u1 D m m1 m2 m3 T v4 d i2 L L12 t u F / F / F / F / F / F / F / F / F / F / F / F / F / F / F / F / F / F / / NF x / NF x / / NF x / / NF x / / NF x / / NF x / / NF x / / NF x / / NF x /

61 DIENSIONS QADRPLE REDCTION k C4 a10 L1 O S4 t i2 L12 L N3 N4 m2 N t1 v4 T L14 O7 V1 a9 P3 m3 O D Od u f4 N1 N2 h1 v2 v3 Od1 u1 O d1 m m1 m a9 a10 C4 f4 h1 N N1 N2 N3 N4 O7 P3 S4 v1 v2 v3 F F F F F F F F k d1 L1 L14 t1 u1 D m m1 m2 m3 T v4 d i2 L L12 t u NF F / / x / NF F / / x / NF F / / x / NF F / / x / NF F / / x / NF F / / x / NF F / / x / NF F / / x /

62 FAN COOLED NITS Column 10 Entry For reducer fan kit modules enter S in column 10 or if used in conjunction with a reducer backstop module kit Y Z CW rotation CCW rotation Dimensions of Fan Cooled nits L15 OB8 Shaft end detail as standard unit øb8 k L13 L15 F F F F

63 The reducer units listed below can be fitted with an internal backstop, this has no effect of the external unit size. The backstop device incorporates high quality centrifugal lift off sprags which are wear free above the lift off speed (n min). To ensure correct operation input speed must exceed lift off speed. Suitable for ambient temperature -40 o C to o F REDCER BACKSTOP ODLE Column 10 Entry For reducer backstop modules enter: W for CCW rotation (or Z if used in conjunction with a fan kit) X for CW rotation (or Y if used in conjunction with a fan kit) Size Lift off Speed ( n min) (at inputshaft) (speed) Rated Locking Torque ( T max ) (at inputshaft) (lb.in) F F F K F F F F F F F F F Rotation of outputshaft must be specified when ordering as viewed from the outputshaft end (as shown in the diagram) CW - Free Rotation - Clockwise Locked - Anticlockwise CW AC - Free Rotation - Anticlockwise Locked - Clockwise CW 60

64 DIENSIONS TORQE BSES & OTPT FLANGE B C E F A B (min) C a9 E F G F F F F F F F F F O7 c1 f1 s1 L Oe1 P3 Od Oa1 Ob1 OG OA a9 u L12 V1 i2 i3 m3 m1 t m a1 b1 c1 e1 f1 m m1 m3 O7 P3 s1 V1 d i2 i3 L L12 t u F (x4) F (x4) / F (x4) / F (x4) / F (x4) / F (x4) / F (x4) / F (x4) / F (x4) /

65 DIENSIONS C (B14) FLANGE m Oe5 m m m OQ S1 F02, F04, F05 F03 F06, F07 F08 m f F F09 m O r O R F02 - F05 F06 - F10 F10 e5 f F m Q r (h7) R (7) S1 F x 0.47 F x 0.47 F x 0.47 F x 0.47 F x 0.79 F x 0.79 F x 0.79 F x 1.06 F x

66 DIENSIONS STANDARD BORE ASSEBLY Assembly on Shaft - Customers Shaft Detail T L2 L L1 R u1 m Od Oda Od L3 L4 L5 Size d da L L1 L2 L3 L4 L5 m N (lb.in) R T u1 F / /8 NF 0.88 deep / F / /8 NF 0.88 deep / F / /2 NF 1.25 deep / F / /8 NF 1.42 deep / F / /8 NF 1.42 deep / F / /8 NF 1.42 deep / F / /4 NF 1.65 deep / F / /4 NF 1.65 deep / *F / /4 NF 1.65 deep * * / * F10 Key must be rectangular section x0.625 Assembly Instructions 1. Spray the hollow shaft bore and mating diameter of the output shaft with Rocol DFS or equivalent anti-scuffing spray. 2. Fit key into shaft. 3. Fit the circlip into the output sleeve. 4. Fit the spacer tube only if the output shaft has no shoulder, then fit the output shaft into the output sleeve. 5. Secure in place with the washer and bolt. Torque tighten to the values stated in column N of the above table. 63

67 DIENSIONS STANDARD BORE DISASSEBLY Disassembly ethod from Shaft c4 OD Od3 c5 m1 m c6 t Od4 m1 Od3 L2 Od2 u c7 Size c4 c5 c6 c7 D d2 d3 d4 L2 m m1 t u (max) F /8 N F /8 N F /8 N F N F N F N F N F N F N

68 DIENSIONS TAPER RELEASE BSING q L1 Driven achine Side O n Og4 y w Protective Cover Driven Shaft k Thin Walled Bushing Nut Locking Screw Odk a b W m a1 b1 N (min) Step Key (supplied) m u v y End Plate (customer supply) Bush Key (supplied) Thick Walled Bushing OC C1 Ok1 Shaft Key (customersupply) Retaining Ring Taper Bushing Key Bush ollow Shaft Nut Gear SIZE nit Cover a b u v y n L1 m q g4 w F04 (107)TR F06 (115)TR F07 (203)TR F08 (207)TR F09 (215)TR F10 (307)TR Consult standard unit selection tables for power and torque ratings. All other gear unit dimensions may be obtained from the standard unit dimension pages. 65

69 DIENSIONS TAPER RELEASE BSING SIZE F04 (107)TR F06 (115)TR F07 (203)TR F08 (207)TR F09 (215)TR F10 (307)TR Driven shaft driven shaft keyway driven shaft end plate diameter * bushing bushing (Ødk) style width min circlip weight (W) depth () length ** a1 K N (min) ØC C1 K1 (lbs) (b1) / Thick 1/4 1/ /2 NC /8 NC N / Thick 1/4 1/ /2 NC /8 NC N / Thick 1/4 1/ /2 NC /8 NC N / Thin 1/4 1/ /2 NC /8 NC N / Thin 3/8 3/ /2 NC /8 NC N / 1/184 Thick 1/4 1/ /2 NC /8 NC N / Thick 1/4 1/ /2 NC /8 NC N / Thick 3/8 3/ /2 NC /8 NC N / Thick 3/8 3/ /2 NC /8 NC N / Thin 3/8 3/ /2 NC /8 NC N / Thin 3/8 3/ /2 NC /8 NC N / Thin 3/8 3/ /2 NC /8 NC N / Thin 1/2 1/ /2 NC /8 NC N / Thick 3/8 3/ /8 NC /4 NC N / Thick 3/8 3/ /8 NC /4 NC N / Thick 3/8 3/ /8 NC /4 NC N / 1/683 Thick 3/8 3/ /8 NC /4 NC N / Thick 3/8 3/ /8 NC /4 NC N / Thin 1/2 1/ /8 NC /4 NC N / Thin 1/2 1/ /8 NC /4 NC N / Thin 1/2 1/ /8 NC /4 NC N / Thin 1/2 1/ /8 NC /4 NC N / Thick 3/16 5/ /8 NC /4 NC N / Thick 3/8 3/ /8 NC /4 NC N / Thick 3/8 3/ /8 NC /4 NC N / Thick 3/8 3/ /8 NC /4 NC N / 1/683 Thick 3/8 3/ /8 NC /4 NC N / Thick 3/8 3/ /8 NC /4 NC N / Thick 1/2 1/ /8 NC /4 NC N / Thin 1/2 1/ /8 NC /4 NC N / Thin 1/2 1/ /8 NC /4 NC N / Thin 1/2 1/ /8 NC /4 NC N / Thin 1/2 1/ /8 NC /4 NC N / Thin 5/8 5/ /8 NC /4 NC N / Thick 1/2 1/ /8 NC NC N / Thick 1/2 1/ /8 NC NC N / Thick 1/2 1/ /8 NC NC N / Thick 1/2 1/ /8 NC NC N / Thin 5/8 5/ /8 NC NC N / Thin 5/8 5/ /8 NC NC N / Thin 5/8 5/ /8 NC NC N / Thin 3/4 3/ /8 NC NC N / Thick 1/2 1/ NC /8 NC N / Thick 1/2 1/ NC /8 NC N / Thick 1/2 1/ NC /8 NC N / Thick 5/8 5/ NC /8 NC N / Thick 5/8 5/ NC /8 NC N / Thin 5/8 5/ NC /8 NC N / Thin 3/4 3/ NC /8 NC N / Thin 3/4 3/ NC /8 NC N / Thin 3/4 3/ NC /8 NC N / Thin 7/8 7/ NC /8 NC N

70 SRINK DISK f4 Od7 OD m3 m2 OD1 Og4 Driven achine Side m1 w7 Tq Protective Cover Od (h6) m5 Od1-0.3 m4 Od1 (h6) size D D1 d d1 d7 f4 m1 m2 m3 m4 (min) m5 (min) g4 w7 Tq (lb.in) F / / F / / F / / F / / F / /

71 DIENSIONS SCREW CONVEYOR L m 3 x O S D L3 L2 L2 BOLT n Axial Thrust Fa m2 m1 n Other dimensions can be obtained from the standard unit dimensions pages Size F04 F06 F07 F08 F09 Shaft Gear nit D L L2 L3 S m m1 m2 n BOLT Fa max (lb s) / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / /

72 SIPPING SPECIFICATION Weight (Lb s) nit size F0223 F0233 F0323 F0333 F0343 F0423 F0433 F0443 F0523 F0533 F0543 F0623 F0633 F0643 F0723 F0733 F0743 F0823 F0833 F0843 F0923 F0933 F0943 F1023 F1033 F1043 Reducer Version Shaft N/A Flange C 143TC 145TC 182TC 184TC 213TC 215TC 254TC 256TC 284TC 286TC 324TC 326TC Without otor Including otor Without otor Including otor Without otor Including otor Without otor Including otor Without otor Including otor Without otor Including otor Without otor Including otor Without otor Including otor Without otor Including otor Without otor Including otor Without otor Including otor Without otor Including otor Without otor Including otor All weights exclude lubricant and are for standard shaft mount units, For units with a flange or solid output shaft - add the weight of flange or shaft (as shown at top of table) 69

73 PRODCT SAFETY INFORATION Product Safety Information IPORTANT General - The following information is important in ensuring safety. It must be brought to the attention of personnel involved in the selection of the equipment, those responsible for the design of the machinery in which it is to be incorporated and those involved in its installation, use and maintenance. The equipment will operate safely provided it is selected, installed, used and maintained properly. As with any power transmission equipment proper precautions must be taken as indicated in the following paragraphs, to ensure safety. Potential azards - these are not necessarily listed in any order of severity as the degree of danger varies in individual circumstances. It is important therefore that the list is studied in its entirety:- 1) Fire/Explosion (a) Oil mists and vapour are generated within gear units. It is therefore dangerous to use naked lights in the proximity of gearbox openings, due to the risk of fire or explosion. (b) In the event of fire or serious overheating (over 300 o C), certain materials (rubber, plastics, etc.) may decompose and produce fumes. Care should be taken to avoid exposure to the fumes, and the remains of burned or overheated plastic/rubber materials should be handled with rubber gloves. 2) Guards - Rotating shafts and couplings must be guarded to eliminate the possibility of physical contact or entanglement of clothing. It should be of rigid construction and firmly secured. 3) Noise - igh speed gearboxes and gearbox driven machinery may produce noise levels which are damaging to the hearing with prolonged exposure. Ear defenders should be provided for personnel in these circumstances. Reference should be made to the Department of Employment Code of Practice for reducing exposure of employed persons to noise. 4) Lifting - Where provided (on larger units) only the lifting points or eyebolts must be used for lifting operations (see maintenance manual or general arrangement drawing for lifting point positions). Failure to use the lifting points provided may result in personal injury and/or damage to the product or surrounding equipment. Keep clear of raised equipment. 5) Lubricants and Lubrication (a) Prolonged contact with lubricants can be detrimental to the skin. The manufacturer's instruction must be followed when handling lubricants. (b) The lubrication status of the equipment must be checked before commissioning. Read and carry out all instructions on the lubricant plate and in the installation and maintenance literature. eed all warning tags. Failure to do so could result in mechanical damage and in extreme cases risk of injury to personnel. 6) Electrical Equipment - Observe hazard warnings on electrical equipment and isolate power before working on the gearbox or associated equipment, in order to prevent the machinery being started. 7) Installation, aintenance and Storage (a) In the event that equipment is to be held in storage, for a period exceeding 6 months, prior to installation or commissioning, application engineering must be consulted regarding special preservation requirements. nless otherwise agreed, equipment must be stored in a building protected from extremes of temperature and humidity to prevent deterioration. The rotating components (gears and shafts) must be turned a few revolutions once a month (to prevent bearings brinelling). (b) External gearbox components may be supplied with preservative materials applied, in the form of a "waxed" tape overwrap or wax film preservative. Gloves should be worn when removing these materials. The former can be removed manually, the latter using white spirit as a solvent. Preservatives applied to the internal parts of the gear units do not require removal prior to operation. (c) Installation must be performed in accordance with the manufacturer's instructions and be undertaken by suitably qualified personnel. (d) Before working on a gearbox or associated equipment, ensure that the load has been removed from the system to eliminate the possibility of any movement of the machinery and isolate power supply. Where necessary, provide mechanical means to ensure the machinery cannot move or rotate. Ensure removal of such devices after work is complete. (e) Ensure the proper maintenance of gearboxes in operation. se only the correct tools and approved spare parts for repair and maintenance. Consult the aintenance anual before dismantling or performing maintenance work. 8) ot Surfaces and Lubricants (a) During operation, gear units may become sufficiently hot to cause skin burns. Care must be taken to avoid accidental contact. (b) After extended running the lubricant in gear units and lubrication systems may reach temperatures sufficient to cause burns. Allow equipment to cool before servicing or performing adjustments. 9) Selection and Design (a) Where gear units provide a backstop facility, ensure that back-up systems are provided if failure of the backstop device would endanger personnel or result in damage. (b) The driving and driven equipment must be correctly selected to ensure that the complete machinery installation will perform satisfactorily, avoiding system critical speeds, system torsional vibration, etc. (c) The equipment must not be operated in an environment or at speeds, powers, torques or with external loads beyond those for which it was designed. (d) As improvements in design are being made continually the contents of this catalogue are not to be regarded as binding in detail, and drawings and capacities are subject to alterations without notice. The above guidance is based on the current state of knowledge and our best assessment of the potential hazards in the operation of the gear units. Any further information or clarification required may be obtained by contacting an Application Engineer. 70

74 CONTACT S ASTRALIA DENARK SWEDEN & NORWAY NITED KINGDO Radicon Transmission (Australia) PTY Ltd Australia Tel: Benzler Transmission A/S Dalager 1 DK-2605 Brøndby, Denmark Tel: Fax: AB Benzlers Porfyrgatan elsingborg Sweden Tel: Fax: Radicon Transmission K Ltd nit J3 Lowfields Business Park, Lowfields Way, Elland West Yorkshire, X5 9DA Tel: Fax: EROPE FINLAND TAILAND SA Benzler TBA BV Jachthavenweg 2 NL-5928 NT Venlo Germany Tel: Fax: Italy Tel: Netherlands & the rest of Europe Tel: Fax: Oy Benzler AB Vanha Talvitie 3C FI elsingfors, Finland Tel: Fax: Radicon Transmission (Thailand) Ltd 700/43 oo 6 Amata Nakorn Industrial Estate Tumbol Klongtumru uang, Chonburi Thailand Tel: Fax: Radicon Drive Systems, Inc Alft Lane Elgin Chicago Illinois SA Tel: Fax: INDIA Elecon. Engineering Company Ltd. Anand Sojitra Road Vallabh Vidyanagar Gujarat India Tel:

75 Benzlers Denmark Finland Germany Italy Sweden The Netherlands Radicon Thailand nited Kingdom SA