Gearmotor Section... Page B-2-B-98

Transcription

1 GEARMOTORS Size -9 Range Gearmotor Section... Page B--B-98 Reducer Section... Page B-100-B-1 For Ratings < 7,600 In. Lbs. - See Catalog or B-1

2 FEATURES and BENEFITS GEARMOTORS TYPE INLINE HELICAL SERIES 000 GEARMOTORS FEATURES Design Features 1. Gears and shafts are made of 10 heat treated nickel chromium molybdenum steel. Helical gearing is skived, superfinished, or ground after case hardening.. Gearbox is delivered filled with synthetic oil, ready to use. 3. Multiple breather locations.. Double lip seals are installed on plunge ground shafts. 5. Innovative self-locking taper shaft connection (motor to gear) allows on-site replacement without removing oil, primary pinion, or disconnecting the load. This ensures precision alignment and eliminates fretting to expedite motor removal. 6. Magnetic drain plug is supplied as standard. 7. Corrosion resistant cast iron housings are one piece, reinforced and ribbed for extra strength. B-

3 Table of Contents GEARMOTORS Section Page Mounting Versatility and Size Range... Motor Options... 5 Gearmotor Selection (constant speed) Gearmotor Selection (variable speed) Catalog Nomenclature Mounting Positions... 1 Electrical Connection Options AGMA Application Classifications Modifications, Options and Accessories Lubrication Gearmotor Selection Tables Dimension Prints (inch) Three Phase Footed Three Phase Flange Mounted Combined Single Phase Footed Combined Three Phase Footed Single Phase Flange Mounted Three Phase Flange Mounted Dimension Print Supplements Metric Output Shafts INTELLIGEAR B-3

4 MOUNTING VERSATILITY & SIZE RANGE GEARMOTORS Foot Mount Frames 9 Max. 150,000 in. lbs. Three Phase TEFC 1/3 75 HP CORRO-DUTY 1/3 75 HP Flange Mount Frames 8 Max. 89,000 in. lbs. Modular Input Assembly Frames 9 Single Phase TEFC 1/3 5 HP High Ratio Foot Mount Frames 9 Max. 150,000 in. lbs. Explosionproof 1/3 50 HP High Ratio Flange Mount Frames 8 Max. 89,000 in. lbs. Intelligear 1/3 5 HP For Sizes 30-3 Torque Range to 7600 In. Lbs. See Catalog B-

5 MOTOR OPTIONS GEARMOTORS TEFC THREE PHASE Suitable for general purpose industrial applications Energy saving, high efficiency design standard 1.5 service factor through 30 HP; 1.15 service factor above 30 HP Suitable for 50 Hz, 190/380 VAC through 30 HP Premium class F Allguard insulation standard 0 C ambient, NEMA B design, continuous duty Premium efficiency available Inverter Duty option per NEMA part 31 available Designed for washdown applications and industries including waste treatment, mining and lumber. All cast iron construction (56 and 10 frames are rolled steel) Premium efficiency standard 3 HP and above 1.15 service factor, class F Allguard insulation Condensation drains in motor and conduit box 0 C ambient, NEMA design B, continuous duty Inverter Duty option per NEMA part 31 available CORRO-DUTY For agricultural, light material handling, textile, and light pumping applications 1.5 service factor (1.15 service factor, 1 HP, 8 frame) (1.0 service factor, through 5 HP) Capacitor start (capacitor run above 1/ HP, 8 frame) (capacitor run above 1 HP, frames) Class B insulation, continuous duty, reversible TEFC SINGLE PHASE Ideal for the petro-chemical, grain, mining, and chemical industries Class I, group D, class II, groups F and G All cast iron construction (plastic fan cover) 1.0 service factor, class B insulation 0 C ambient, NEMA B design, continuous duty UL approved inverter duty per NEMA part 31 available EXPLOSIONPROOF Variable speed gearmotor with NEMA 3R/1 enclosure "Onboard" pushbutton and remote speed changing options pre-programmed 6:1 constant torque speed range Versions for 60V input power supplies from 1/3 to 5 HP 1/30V and 30V through HP UL, CUL and CE INTELLIGEAR B-5

6 GEARMOTOR SELECTION GEARMOTORS SELECTION INFORMATION SIZE SELECTION 1. Input HP Based on application data.. Speed / Ratio Obtain either desired output speed (RPM) or gearbox ratio based on application. 3. AGMA Load Class There are three standard classifications for gearmotor applications: CLASS I - Uniform loading, 3-10 hours per day, service factor 1.0 (minimum). CLASS II - Uniform loading over 10 hours per day or moderate shock loading up to 10 hours per day; service factor 1. (minimum). CLASS III - Moderate shock loading over 10 hours per day or heavy shock loading up to 10 hours per day; service factor.0 (minimum). The tables on pages B-1 through B-16 are based on past operating experience within the industries listed and information gathered by AGMA. If the user has data reflecting greater severity than normal industry usage, then AGMA class should be increased. Choose the AGMA class for your given application based on this criteria. If your application cannot be found, use the following table to determine service factor. Step 1 - Locate gearmotor selection tables (pages B- to B-63) based on input HP. Step - Choose the appropriate nominal speed required. Step 3 -Select the correct gearmotor based on AGMA class or service factor determined in selection information. Step - Verify overhung load ratings where required (see below). When a sprocket, sheave, pulley, or pinion is mounted on the take-off shaft of a gearmotor, it is necessary to calculate the overhung load. This calculated load must be compared with the gearbox capacity listed to make sure the gearbox will not be overloaded. To calculate the overhung load you need to know the torque or horsepower at the take-off shaft and the location along the shaft at which the load is applied. A. If torque is known: OHL = B. If horsepower is known: OHL = OVERHUNG LOAD T x K x LLF r 6305 x HP x K x LLF RPM x r Duty Cycle Hours Operation CONTINUOUS Uniform Load U Moderate Shock Load M Heavy Shock Load V Where: OHL = Overhung load (pounds) T = Torque (in. lbs.) r = Radius of driving member (in.) HP = Horsepower K = Drive type factor LLF = Load location factor FREQUENT STARTS/STOPS* *Greater than 10 per hour DRIVING MEMBER VALUE OF K Chain Drive 1.00 Pinion 1.5 V-Belt 1.50 Flat Belt.50 LOAD LOCATION VALUE OF LLF End of shaft extension 1.0 Center of shaft extension 1.00 Shaft extension shoulder 0.80 B-6

7 GEARMOTOR SELECTION GEARMOTORS SELECTION EXAMPLE A horizontal, foot mounted gearmotor is required to operate a uniformly loaded assembly conveyor at RPM, hours per day. An 8" diameter sprocket is mounted at the end of the shaft and drives the conveyor with a chain. The load is 7.5 HP and customer requests a standard 30/60 volt TEFC motor end and normally closed breather in gear case. Step 1... AGMA service classification tables on pages B-1 though B-16 indicate that this is a CLASS II application. Step... Page B- gearmotor table indicates that a frame 18T-50 will do the job. Output AGMA Service Output Torque OHL Nominal Frame Size Std. Motor RPM Class Factor in-lb lb Ratio Gear Motor Types I,II,III T T,C,X Step 3... To check overhung load for the example: Sprocket Diameter 8 r = = = K = 1.0 (chain drive) LLF = 1. (sprocket on end of shaft) HP = 7.5 Torque formula: OHL = OHL = 6305 x HP x K x LLF RPM x r 6305 x 7.5 x 1.0 x 1. x = 33 lbs. Overhung load capacity of 5051 lbs. listed is greater than the calculated value of 33 lbs. Step... Step 5... Check modification M1 from page B-18 for normally closed breather. On 50 this breather is standard. Catalog designation will be: -50-S-B3-0-MT-13T-7.5 B-7

8 GEARMOTOR SELECTION VARIABLE SPEED SELECTION INFORMATION SIZE SELECTION 1. Determine Installation Environment Control enclosure is NEMA 1/3R. Input HP For constant torque loads this is at maximum speed of range 3. Speed Range Confirm maximum and mininum of 6:1 range. Step 1 - Step - Locate gearmotor selection tables based on the input HP required at maximum speed of the range. Select the "Output RPM" closest to the maximum speed of the range desired. If the motor HP is 5, make the RPM selection using the following formula: "Output RPM" Selection = Max. Speed of Range 1.. Determine Control Power Supply Phase and voltage. Power Supply Input HP' s 1 ph / 30 v.33 to 3 ph / 30 v.33 to 3 ph / 60 v.33 to 5 3 ph / special R. O. 5. Mechanical Service Factoring of Gear Refer to Page B-6 for this procedure. Note: INTELLIGEAR application for 1 phase power supply is limited to 10 starts per hour. Step 3 - Note the gear ratio after step. Step - Step 5 - Step 6 - Step 7 - Select correct gearmotor that meets or exceeds the AGMA class or service factor determined in the selection information. Verify overhung load rating where applicable per formulas on Page B-6. Confirm input power supply is compatible with HP of selection and record speed adjustment option desired for the applicaiton. Refering to Page B-13, determine if an alternate controller location is required for the application. Default location is "FO" (at 1 O'Clock). 6. Determine Speed Adjustment Option Select from: P1 P P3 P R RP RI RD RC = Run/Stop/Speed Pot. mounted on INTELLIGEAR enclosure = Forward/Reverse/Stop/Pot. mounted on INTELLIGEAR enclosure - Speed Pot. (only) mounted on INTELLIGEAR enclosure (start/stop by others) = Speed Pot. (only) mounted inside INTELLIGEAR enclosure (start/stop by others) = Remote Signal Following (0-10VDC or -0mA supplied by others) = Remote From Fieldbus - Profibus DP = Remote From Fieldbus - INTERBUS S = Remote From Fieldbus - DEVICENET = Remote From Fieldbus - CAN OPEN Maximum motor RPM will be 7 Hz for 5HP INTELLIGEAR. B-8

9 GEARMOTOR SELECTION INTELLIGEAR SELECTION EXAMPLE A foot mounted gearmotor is required to operate a positive displacement pump from 5 to 9 RPM, 16 hours a day in a waste treatment plant. The output shaft will be coupled to the pump. The customer required.5 HP at the maximum RPM. The jobsite power supply is 3 phase and 60 VAC. The control of speed requires the INTELLIGEAR to follow a -0 ma signal supplied by a process control system. Step 1... The closest gearmotor HP to meet this application is a 5 HP design. Step... Determine the specific selection output RPM and ratio for 5 HP INTELLIGEAR Maximum Speed / 1. = "Selection Table" RPM 5 / 1. = approx. 5 RPM Step 3... AGMA service classification indicates this is an AGMA CLASS II application. From this information, on Page B-0 a 0 and motor frame 18T with 0:1 nominal ratio is the correct gearmotor. Output AGMA Service Output Torque OHL Nominal Frame Size Std. Motor RPM Class Factor in-lb lb Ratio Gear Motor Types I, II T T,S,C,X,IG Step... This application does not involve any OHL calculations due to coupling connection. Step 5... The power supply of 3 phase / 60 VAC is ok for 5 HP INTELLIGEAR and the speed changing option will be "R" per table on preceding page. Step 6... Catalog designation will be: 0 S B3 0 T 18T 5 w/"r" speed option B-9

10 ORDERING GEARMOTORS 0 S B3 0 T 18T 5 Choose one Based on Application Based on Selection Gear Number of Type Frame Reductions Mounting Configuration Choose one Mounting Position Ratio Input Motor Frame Horsepower Modification Code(s) = 1 stage 0 = stages 03 = 3 stages 0 = stages 05 = 5 stages 06 = 6 stages S = BS = SM = BSM = Foot Mount Flange Mount Metric Foot Mount Metric Flange Mount see page B-1 Use Nominal Ratio Selected Use Catalog Designation From Table Below and B T 180T 10T 50T 80T 30T 360T 1/3 1/ Number of Modification(s) From Pages B-17 - B STANDARD MOTOR INPUT TYPES Motor Type Speed - Design C atalog Motor Description (reference only) D esignation Frame(s) Voltage Poles S MR 56-15TY 115/30 Single ( Single Phase TEFC) MR 18T 30 MT 56-86T 08-30/60 MB 3T - 365T 30/60 Single MV T 575 Standard Efficiency MO 56-56T 30/60 6 T MW 56-56T (Three Phase TEFC) Single MY 13T - 365T 30/60 Premium Efficiency MZ 13T - 365T 575 MI T 30/60 Inverter Duty MD T 575 Note: Refer to page B-11 for additional motor types. B-10

11 ORDERING GEARMOTORS Motor Type T (Three Phase TEFC) C ALTERNATE MOTOR INPUT TYPES Speed - Design Two Speed (Constant Torque) Single Single Standard Efficiency Single High Efficiency C atalog Motor Description (not required) D esignation Frame(s) * Defines input power supply to controller. All motors and controllers' output is three phase. Voltage Poles U 56-86T 30 /8-1 Winding U T 60 /8-1 Winding U T 575 /8-1 Winding Z1 Z T Special T Special 6 MC 56-15TY 30/60 MG 56-15TY 575 MF 56-56T 30/60 6 MC 13T - 365T 30/60 MG 13T - 365T 575 CORRO-DUTY C 56-86T 30 /8-1 Winding Three Phase Two Speed (Constant Torque) C T 60 /8-1 Winding C T 575 /8-1 Winding Inverter Duty Single CI T 30/60 CD T 575 MX 56-15TY 30/60 ME 56-15TY 575 Z T 30/60 6 X X 56-86T 30 /8-1 Winding Explosionproof Two Speed (Constant Torque) X T 60 /8-1 Winding X T 575 /8-1 Winding IG INTELLIGEAR TEFC/NEMA 3R+1 (motor/controller) Inverter Duty 6:1 Range (Constant Torque) Variable Speed XI T 30/ 60 XD T 575 TS T T 56-15TY 56-15TY 56-18T 1/30 * 30 * 60 * B-11

12 MOUNTING POSITIONS GEARMOTORS FOOT MOUNT S SINGLE REDUCTION MULTIPLE REDUCTION B3 B8 B3 B8 B6 B7 B6 B7 V5 V6 V5 V6 FLANGE MOUNT BS SINGLE REDUCTION MULTIPLE REDUCTION B5 B5 B5 V1 B53 V1 V3 B5 V3 B-1

13 ELECTRICAL CONNECTION OPTIONS GEARMOTORS F0 Conduit Box Location When ordering a conventional 000 gearmotor, specify the desired conduit box location when viewing unit output shaft in B3 or B5 position. If no option is specified, the "F1" location will be supplied. F1 (Standard) F CONDUIT BOX F0 (Standard) Controller Location When ordering an INTELLIGEAR Series 000 gearmotor, you can specify the controller location and conduit entry location when viewing the unit output shaft in B3 or B5 position. If no options are specified, the "F0" controller location will be supplied. F1 F INTELLIGEAR CONTROLLER B A (Standard) Cable Entry INTELLIGEAR Cable Entry can be from either side of enclosure. If no option is specified, "A" will be supplied. CABLE ENTRY B-13

14 AGMA APPLICATION CLASSIFICATION GEARMOTORS U: Uniform load M: Moderate shock load V: Heavy shock load Application Load Class Application Load Class Application Load Class Up to Over hrs/day hrs/day Up to Over hrs/day hrs/day Up to Over hrs/day hrs/day AGITATORS Paper Mills M II II Pure Liquids U I II Liquids & Solids M II II Liquids - Variable Density M II II APRON CONVEYORS Uniformly Loaded or Fed U I II Heavy Duty M II II APRON FEEDERS M II II ASSEMBLY CONVEYORS Uniformly Loaded or Fed U I II Heavy Duty M II II BALL MILLS V III III BARKING Drums V - III Hydraulic Auxiliaries V - III Mechanical V - III BAR SCREENS (Sewage) U I II BATCHERS (Textile) M II II BEATERS & PULPERS (Paper) U - II BELT CONVEYORS Uniformly Loaded or Fed U I II Heavy Duty M II II BELT FEEDERS M II II BENDING ROLLS (Machine) M II II BLEACHERS (Paper) M - II BLOWERS Centrifugal U I II Lobe M II II Vane U I II BOTTLING MACHINERY U I II BREWING & DISTILLING Bottling Machinery U I II Brew Kettles, Cont. Duty U - II Can Filling Machines U I II Cookers - Cont. Duty U - II Mash Tubs - Cont. Duty U - II Scale Hoppers - Frequent Starts M II II BRICK PRESS (Clay Working) V III III BRIQUETTE MACHINES (Clay Working) V III III BUCKET Conveyors, Uniform U I II Conveyors, Heavy Duty M II II Elevators Cont. U I II Elevators Uniform U I II Elevators, Heavy Duty M II II CALENDERS Paper U - II Super (Paper) U - II Rubber M II II Textile M II II CANE KNIVES M II II CAN FILLING MACHINES U I II CARD MACHINES (Textile) M II II CAR DUMPERS V III - CAR PULLERS M II - CEMENT KILNS Refer to Tech. Service CENTRIFUGAL Blowers, Compressors, Discharge Elevators or Pumps U I II CHAIN CONVEYORS Uniformly Loaded or Fed U I II Heavy Duty M II II CHEMICAL FEEDERS (Sewage) U I II CLARIFIERS U I II CLASSIFIERS M II II CLAY WORKING INDUSTRY Brick Press V III III Briquette Machine V III III Clay Working Machinery M II II Pug Mill M II II COLLECTORS (Sewage) U I II COMPRESSORS Centrifugal U I II Lobe M II II Reciprocating, Multi - Cylinder M II II Single - Cylinder V III III CONCRETE MIXERS Continuous M II II Intermittent U I - CONVERTING MACHINES (Paper) M - II CONVEYORS - Uniformly Loaded or Fed: Apron, Assembly, Belt, Bucket, Chain, Flight, Oven, Screw U I II CONVEYORS - Heavy Duty Not Uniformly Fed: Apron, Assembly, Belt, Bucket, Chain, Flight, Oven, Screw M II II Live Roll (Package) U I II Reciprocating, shaker V III III COOKERS (Brewing & Distiling) (Food)U I II COOLING TOWER FANS Induced Draft M II II Forced Draft Refer to Tech. Service COUCH (Paper) M - II CRANES & HOISTS Main Hoists Heavy Duty V III III Medium Duty M II II Reversing V II II Skip Hoists M II II Trolley DriveM II II Bridge Drive M II II CRUSHERS Ore or Stone V III III CUTTERS (Paper) V - III CYLINDERS (Paper) M - II DEWATERING SCREENS (Sewage) M II II DISC FEEDERS U I II DISTILLING (See Brewing) DOUBLE ACTING PUMPS or more Cylinders M II II Single Cylinder Refer to Tech. Service DOUGH MIXER (Food) M II II DRAW BENCH (Metal Mills) Carriage & Main Drive V III III DREDGES Cable Reels M II - Conveyors M II II Cutter Head Drives V III III Jig Drives V III III Maneuvering Winches M II - Pumps M II II Screen Drives V III III Stackers M II II Utility Winches M II - B-1

15 AGMA APPLICATION CLASSIFICATION GEARMOTORS U: Uniform load M: Moderate shock load V: Heavy shock load Application Load Class Application Load Class Application Load Class Up to Over Up to Over Up to Over hrs/day hrs/day hrs/day hrs/day hrs/day hrs/day DRYERS (Paper) U - II DRYERS & COOLERS (Mills, Rotary) M II II DYEING MACHINERY (Textile) M II II ELEVATORS Bucket - Uniform Load U I II Bucket - Heavy Duty M II II Bucket - Continuous U I II Centrifugal Discharge U I II Escalators U I II Freight M II II Gravity Discharge U I II Man Lifts, Passenger Refer to Tech. Service ESCALATORS U I II FANS Centrifugal M II II Cooling Towers Induced Draft M II II Forced Draft Refer to Tech. Service Induced Draft M II II Large (Mine, etc.) M II II Large Industrial M II II Light (Small Diameter) U I II FEEDERS Apron, belt M II II Disc U I II Reciprocating V III III Screw M II II FELT Stretchers (Paper) U - II Whippers (Paper) U - II FLIGHT Conveyors, Uniform U I II Conveyors, Heavy M II II FOOD INDUSTRY Beet Slicers M II II Bottling, Can Filling Mach. U I II Cereal Cookers U I II Dough Mixers M II II Meat Grinders M II II FORMING MACHINES (Metal Mills) V III III GENERATORS (Not welding)u I II GRAVITY DISCHARGE ELEVATORS U I II GRIT COLLECTORS (Sewage) U I II HAMMER MILLS V III III INDUCED DRAFT FANS M II II JORDANS (Paper) U - II KILNS (Mills, Rotary) M II II Cement Refer to Tech. Service LAUNDRY WASHERS & TUMBLERS M II II LINE SHAFTS Heavy Shock Load V III III Moderate Shock Load M II II Uniform Load U I II LIVE ROLL CONVEYORS Package U I II LOBE BLOWER OR COMPRESSORS M II II LOG HAULS (Paper & Lumber) V III III LOOMS (Textile) M II II LUMBER INDUSTRY Barkers - Spindle Feed V II III Barkers - Main Drive V III III Carriage Drive Refer to Tech. Service Conveyors Burner V II III Main or Heavy Duty V II III Main Log V III III Re-Saw Merry-Go-RoundV II III Slab V III III Transfer V II III Chains - Floor V II III Chains - Green V II III Cut-Off Saws-Chain V II III Cut-Off Saws-Drag V II III Debarking Drums V III III Feeds - Edger V II III Feeds - Gang V III III Feeds - Trimmer V II III Log Deck V III III Log Hauls - Incline, Well TypeV III III Log Turning Devices V III III Planner Feed V II III Planer Tilting Hoists V II III Rolls - Live-Off Bearing Roll Cases V III III Sorting Table V II III Tipple Hoist V II III Transfers - Chain V II III Transfers - Craneway V II III Tray Drives V II III MACHINE TOOLS Auxiliary Drives U I II Bending Rolls M II II Main Drives M II II Notching Press (Belted) Consult Office Plate Planers V III III Punch Press (Geared) V III III Tapping Machines V III III MANGLE (Textile) M II II MASH TUBS (Brewing & Distilling) U - II MEAT GRINDER (Food) M II II METAL MILLS Draw Bench Carriages & Main Drives V III III Forming Machines V III III Pinch, Dryer & Scrubber Rolls Reversing Consult Office Slitters M II II Table Conveyors, Non-Reversing M II III ReversingV - III Wire Drawing & Flattening Machines M II III Wire Winding Machines M II II MILLS, ROTARY TYPE Ball, Pebble, Rod V III III Cement Kilns Consult Office Coolers, Dryers, Kilns V II II Tumbling Barrels V III III MIXERS (Also see Agitators) Concrete - Continuous M II II Concrete - Intermittent M I - Constant Density U I II Variable Density M II II NAPPERS (Textile) M II II OIL INDUSTRY Chillers M II II Oil Well Pumping Refer to Tech. Service Paraffin Filter Press M II II Rotary Kilns M II II ORE CRUSHERS V III III OVEN CONVEYORS Uniform U I II Heavy Duty M II II B-15

16 AGMA APPLICATION CLASSIFICATION GEARMOTORS U: Uniform load M: Moderate shock load V: Heavy shock load Application Load Class Application Load Class Application Load Class Up to Over Up to Over Up to Over hrs/day hrs/day hrs/day hrs/day hrs/day hrs/day PAPER MILLS Agitator (Mixers) M II II Barker - Auxiliaries - Hyd. V - III Barker, Mechanical V - III Barking Drum V - III Beater & Pulper M - II Bleacher M - II Calenders M - II Calenders - Super M - II Converting Mach.- Except Cutters - Platers M - II Conveyors M - II Couch M - II Cutters, Platers V - III Cylinders U - II Dryers U - II Felt Stretchers U - II Felt Whippers V - III Jordans M - II Log Haul V - III Presses M - II Pulp Machine Reels M - II Stock Chests M - II Suction Rolls M - II Washers & Thickeners M - II Winders M - II PASSENGER ELEVATORS Refer to Tech. Service PEBBLE MILLS V III III PLATE PLANERS V III III PRESSES (Paper) V - III PROPORTIONING PUMPS M II II PUB MILLS (CLAY) M II II PULLERS (Barge Haul) V III III PULP MACHINE REELS U - II PUMPS Centrifugal U I II Proportioning M II II Reciprocating Single Act., 3 or more cyl. M II II Double Act., or more cyl. M II II Single Act., 1 or cyl. Refer to Tech. Service Rotary: Gear, Lobe, Vane U I II PUNCH PRESS (Gear Driven) V III III RECIPROCATING Conveyors, Feeders V III III RECIPROCATING COM- PRESSORS Multi-Cylinder M II II Single cylinder V III III ROD MILLS V III III ROTARY Pumps, Gear, Lobe, Vane U I II Screens (Sand or Gravel) V II II RUBBER INDUSTRY Mixer V III III Rubber Calender M II II Rubber Mill ( or more) M II II Sheeter M II II Tire Building Machines Refer to Tech. Service Tire, Tube Press Openers Refer to Tech. Service Tubers & Strainers M II II SAND MULLERS Refer to Tech. Service SCREENS Air Washing U I II Rotary - Sand or Gravel M II II Traveling Water Intake U I II SCREW CONVEYORS Uniform U I II Heavy Duty or Feeder M II II SCUM BREAKERS (Sewage) M II II SEWAGE DISPOSAL Aerators Refer to Tech. Service Bar Screens U I II Chemical Feeders U I II Collectors U I II Dewatering Screens M II II Grit Collectors U I II Scum Breakers M II II Slow or Rapid Mixers M II II Sludge Collectors U I II Thickeners M II II Vacuum Filters M II II SHAKER CONVEYORS V III III SHEETERS (Rubber) M II II SINGLE ACTING PUMP 1 or Cylinders Refer to Tech. Service 3 or more Cylinders M II II SKIP HOIST M II II SLAB PUSHERS M II II SLITTERS (Metal) M II II SLUDGE COLLECTORS (Sewage) U I II SOAPERS (Textile) M II II SPINNERS (Textile) M II II STEERING GEARS M II II STOCK CHESTS (Paper) U - ii STOKERS U I II STONE CRUSHERS V III III SUCTION ROLLS (Paper) U - II TABLE CONVEYORS (Metal Mills) Non-ReversingV II III Reversing V - III TENTER S (Textile) M II II TEXTILE INDUSTRY Batchers M II II Calenders M II II Card Machines M II II Cloth Finishing Mach. (Calenders, Dryers, Pads, Tenters, Washers) M II II Dry Cans M II II Dyeing Machinery M II II Knitting Machinery Refer to Tech. Service Looms, Mangles, Nappers M II II Range Drives Refer to Tech. Service Soapers, Spinners M II II Tenter Frames M II II Winders M II II Yarn Preparatory Mach. (Cards, Spinners, Slashers) M II II THICKENERS (Sewage) M II II TUMBLING BARRELS V III III VACUUM FILTERS (sewage) M II II VANE BLOWERS U I II WINCHES (Dredges) M II - WINDERS (Paper) U - II (Textile) M II II WINDLASS M II II WIRE Drawing Machines M II III Winding Machines M II II Applications not listed in this table or where the user has data indicating the severity of his usage to be greater than average should be referred to Technical Services. B-16

17 GEARMOTORS MODIFICATIONS, OPTIONS and ACCESSORIES M1 BRAKES INVERTER DUTY GEARMOTORS Many Series 000 three phase gearmotors now incorporate upgraded ALLGUARD wire and insulating materials for inverter service. A one year warranty will be extended for :1 (60-30 Hz) constant torque for standard efficiency design motors and 3:1 (60-0 Hz) constant torque for premium efficiency design motors providing the following conditions are met: motor is non-hazardous 3 phase > 8 frame cable length to controller 100 ft line volts is 80 VAC thermal protection is not required For all other conditions of operation including up to 575 VAC and for hazardous environment services, select a Varidyne inverter duty motor design. These designs include thermostats in winding, a 3 year warranty on the motor, and full compliance with NEMA MG1 Part 31. MOTOR MODIFICATIONS Design These mounted brakes have a direct acting, spring set, electromagnetically released disc design. When power to the brake motor is interrupted, the brake will immediately set and hold. When power is restored, the brake will automatically release. Brake torque must be specified when ordering. Table 1 gives brake torque for stopping and holding load not greater than full load motor torque. An asterisk indicates borderline maximum ratings and should be considered only for holding loads. Refer to office applications involving high inertia loads or frequent starts and stops. Enclosures Standard - Suitable for most indoor non-hazardous applications. Stock SHUR - STOP brakes have this enclosure. Waterproof / Dust-tight - For applications requiring additional brake protection such as Washdown or CORRO-DUTY. Not suitable for hazardous Class dust applications. Subject to production lead time. Explosionproof - When a brake is to be mounted on an explosionproof gearmotor, the brake must have UL approval equal to that of the motor end. Brakes are rated class I group D, class II groups F & G temperature code T3B. Subject to production leadtime. Operating Voltage Production brakes through 15 lb. ft. are supplied with 30/60 volt coils. Brakes 5 lb. ft. and larger are supplied with 60 volt coils. For brakes to operate at a different frequency or voltage, or for brakes to operate from a separate power supply, refer to office. Brakes are furnished with leads suitable for external connection. Mounting Brakes listed in Table 1 are motor mounted. Brakes through 6 lb. ft. are suitable for all mounting positions. For brakes 10 through 35 lb. ft., specify mounting orientation of brake gearmotor. Where vertical mounting of brakes 50 lb. ft. or larger is required, refer to office with mounting and application details. TABLE 1 MAX. HP RATINGS - HIGH SPEED INPUT BRAKE POLE 1800 POLE 6 POLE RPM 1500 RPM POLE TORQUE RPM 1000 RPM (ft-lbs) 1 1/ 1/ 3 1 1/ /* / * 7 1/ / * * 0 0* * *Indicates borderline maximum rating for holding loads only. M PREMIUM EFFICIENCY Premium efficiency motor designs are available starting at 1 HP to meet customer specifications or NRCan legislation. CORRO- DUTY motor 3 HP and all inverter duty motors meet premium efficiency. TEFC and CORRO-DUTY motors ends from 1 through HP design C and therefore are exempt from NRCan efficiency requirements. M3 MULTI-SPEED (3 PHASE ONLY) Gearmotors with 1800 RPM motors as standard can be supplied with two speed, one winding, constant torque, 1800/900 RPM, 1.0 service factor, TEFC motor ends. Note that change in motor frame may change gearbox size. Thus if gear frame is not within allowable range, it may be necessary to change gear frame size. TABLE HP ALLOWABLE GEAR S 5 /.5 15T / T / 5 56T / 7.5 8T / 10 86T / 1.5 3T / 15 36T 7-8 M CANOPY CAP. A canopy cap can be supplied for protection from dripping liquids entering fan end of gearmotor when mounted in a motor fan up position (V1, V5). B-17

18 MODIFICATIONS GEARMOTORS MOTOR MODIFICATIONS CONTINUED M5 FREQUENCY - 50 Hz Motors for operation at 3 phase 50 Hz are available. Standard 50 Hz voltage (detailed in M6) do not require voltage modification. The published output speed based on 1750 RPM input will be reduced by a factor of (1.) at the same gear ratio. EXAMPLE: 100 RPM output, 60 Hz, 1750 RPM input is 83 RPM output, 50 Hz, 150 RPM input. M6 VOLTAGE (3 PHASE ONLY) Standard voltages available are listed in the table below. Other voltages are available and must be specified at order entry and require special voltage adder. FREQUENCY 3 PHASE VOLTAGES THRU 30 HP 60 Hz 00, 30, 30/60, 60, Hz 00, 0, 30, 0/380, 0/0, 380, 15, 60, 500, 575 M7 INSULATION Standard 3 phase TEFC and CORRO-DUTY motor ends have premium class F insulation standard. Single phase TEFC and explosionproof motor ends have class B insulation as standard. Class H insulation and tropical protection are available from production on 3 phase motors only (class H not available on explosion proof). GEAR MODIFICATIONS M11 CORRO-DUTY CORRO-DUTY gear reducers are designed for applications in food processing, chemical, poultry and other industries where a gear reducer will be subjected to extreme humidity, washdown steam, detergents, and mild acids. Construction of CORRO- DUTY gear reducers includes normally closed gearcase breather; exterior of gear painted with corrosion resistant vinyl copolymer alkyd grey paint. USDA approved white paint is also available. M1 BREATHER (Normally closed type) A normally closed breather is available for applications which could contaminate lubricant, such as flying dust. This is supplied standard on frame thru 5. M13 NPT ADAPTER These adapters convert metric threads of breather, drain and/or oil level holes in the reducer to standard NPT threads. They are required for customer additions of site glasses, sight tubes, special breathers, and other plumbing accessories. The adapter(s) is supplied loose for mounting by others. SIZE PART NUMBER - 5 8" NPFT " NPFT M8 SPACE HEATERS Space heaters are recommended for gearmotors installed in damp locations to prevent condensation on the motor windings when the motor is not operating. Leads are brought to the standard motor conduit box. Space heater voltage (115, 30, 60 volts) must be specified when order is entered. M9 THERMAL PROTECTION - Thermostats This protection uses a bi-metal disc thermostat, embedded in the motor winding, connected into the holding circuit of the motor starter. The sensor opens the control circuit, shutting down the motor on over temperature. Thermostats give protection for running overload, abnormally high ambient, voltage unbalance, high or low voltage, and ventilation failure. Thermostats will not give protection for locked rotor, starting overload, and single phasing. M10 THERMAL PROTECTION - Therma-Sentry Therma-Sentry is a full protection system which consists of a solid state electronic controller and thermistor temperature sensors embedded in the motor winding. Therma-Sentry gives protection for all the abnormal conditions of thermostats, plus protection against locked rotor, starting overload, and single phasing. The Therma-Sentry system requires only two leads to connect to the starter panel. Therma-Sentry controller is supplied loose to be separately mounted and separately excited. GEARMOTOR MODIFICATIONS FLANGED OUTPUT (Designated under mounting config.) Gear ends with flanged output (catalog designation BS) are available from stock. SYNTHETIC OIL gearmotors in frames thru 9 are supplied factory filled with a premium synthetic oil. Refer to page B-19 for complete details of lubricants. M15 EXPORT BOXING Export boxing can be provided for "underdeck" transport. When the quantity of gearmotors exceeds five(s) units, refer to the Sales department for most economical accommodations. M16 SPECIAL NAMEPLATE Units can be provided with limited additional special information on the standard product nameplate. When requested, a special nameplate may be provided, stamped with custom markings. B-18

19 AVAILABILITY AND LUBRICATION GEARMOTORS The gearbox is filled with one of the following synthetic oils according to the mounting position specified when ordered (See page B-10) and fitted with a magnetic drain plug. Synthetic lubricants are used in the gearbox due to their wide temperature range. In the event that the gearbox needs to be refilled, see the appropriate maintenance manual for the proper procedure and correct quantity of oil. If synthetic oil is not available check the chart below for acceptable non-synthetic lubricants. NO BACKSTOP Manufacturer -5 F to 15 F (-30 C to 50 C) COFRAN SINTOGEAR 15 MOBIL SHC 69 SHELL OMALA HD 150 STANDARD SYNTHETIC GEAR OIL ACCEPTABLE MINERAL OIL LUBRICANTS - to 1 F 1 to 1 F(-10 C to 50 C) 1 F and Above Manufacturer (-0 C to 10 C) NO BACKSTOP WITH BACKSTOP (50 C +) ISO VG 68 ISO VG 100 ISO VG 150 ISO VG 0 ISO VG 150 ISO VG 30 COFRAN Mecanep 68 GL Cofraline Equitex 100 Mecanep 150 Equilux C000 Super Cofrapoid 80W 90 Mecanep 30 MOBIL Mobil Gear 66 Mobil Gear 67 Mobil Gear 69 Mobil Gear 630 DTE Extra Heavy Mobil Gear 63 SHELL Omala 68 Omala 100 Omala 150 Omala 0 Vitrea 150 Omala 30 Gear Frame OIL CAPACITIES (U.S. Quarts) Mounting Positions B3 B5 B6 B7 B8 B5 B53 B 5 V1(BS) V3 V5 V The Company names and the names of the Lubricants mentioned in the above tables are the tradenames, trademarks and logotypes of the respective companies, and are not owned by EPT. B-19

20 LUBRICATION GEARMOTORS Gear Frame FOOT MOUNTED COMBINED UNITS (U.S. QUARTS) Mounting Positions B3 B8 B6 B7 V5 V6 P rim. S ec. P rim. S ec. P rim. S ec. P rim. S ec. P rim. S ec. P rim. Sec B-0

21 LUBRICATION Gear Frame FLANGED MOUNTED COMBINED UNITS (U.S. QUARTS) Mounting Positions B5 V1 V3 P rim. S ec. P rim. S ec. P rim. Sec B-1

22 SELECTION TABLES 1/3 HP GEARMOTORS General Specifications: Totally enclosed, 60 hertz, 0 C ambient, continuous duty. 1/3 HORSEPOWER Output AGMA Service Output Torque OHL Nominal Frame Size Std. Motor RPM Class Factor in-lb lb Ratio Gear Motor Types 6. III T,C,S,X,IG 5.75 III T,C,S,X,IG.8 III T,C,S,X,IG. I T,C,S,X,IG. II,III T,C,S,X,IG II,III T,C,S,X,IG 3.5 I,II,III T,C,S,X,IG 3 I,II T,C,S,X,IG 3 III T,C,S,X,IG.7 I,II T,C,S,X,IG.7 III T,C,S,X,IG. I,II T,C,S,X,IG. III T,C,S,X,IG. I T,C,S,X,IG. II,III T,C,S,X,IG 1.95 I T,C,S,X,IG 1.95 II,III T,C,S,X,IG Standard Motor Types (see page B-10 for product codes) T TEFC, three phase, 08-30/60 or 575 volts C Corro-Duty, three phase, 30/60 or 575 volts S TEFC, single phase, 115/30 volts X Explosionproof, Cls I Grp D, Cls II Grps F&G, three phase 30/60 or 575 volts IG INTELLIGEAR variable speed for 1/30, 30 or 60V power supplies Overhung loads are at shaft midpoint B-

23 SELECTION TABLES 1/3 HP GEARMOTORS General Specifications: Totally enclosed, 60 hertz, 0 C ambient, continuous duty. 1/3 HORSEPOWER (continued) Output AGMA Service Output Torque OHL Nominal Frame Size Std. Motor RPM Class Factor in-lb lb Ratio Gear Motor Types 1.75 I,II T,C,S,X,IG 1.75 III T,C,S,X,IG 1.5 I,II T,C,S,X,IG 1.5 III T,C,S,X,IG 1. I,II T,C,S,X,IG 1. III T,C,S,X,IG.98 I T,C,S,X,IG.98 II T,C,S,X,IG.98 III T,C,S,X,IG.75 I T,C,S,X,IG.75 II,III T,C,S,X,IG.61 I T,C,S,X,IG.61 II T,C,S,X,IG.61 III T,C,S,X,IG.50 I T,C,S,X,IG.50 II,III T,C,S,X,IG.38 I T,C,S,X,IG.38 II T,C,S,X,IG.38 III T,C,S,X,IG.30 I,II T,C,S,X,IG.30 III T,C,S,X,IG.8 I T,C,S,X,IG.8 II,III T,C,S,X,IG Standard Motor Types (see page B-10 for product codes) T TEFC, three phase, 08-30/60 or 575 volts C Corro-Duty, three phase, 30/60 or 575 volts S TEFC, single phase, 115/30 volts X Explosionproof, Cls I Grp D, Cls II Grps F&G, three phase 30/60 or 575 volts IG INTELLIGEAR variable speed for 1/30, 30 or 60V power supplies Overhung loads are at shaft midpoint B-3

24 SELECTION TABLES 1/ HP GEARMOTORS General Specifications: Totally enclosed, 60 hertz, 0 C ambient, continuous duty. 1/ HORSEPOWER Output AGMA Service Output Torque OHL Nominal Frame Size Std. Motor RPM Class Factor in-lb lb Ratio Gear Motor Types 9. III T,C,X 8. III T,C,X 7.5 III T,C,X 6. II,III T,C,S,X,IG 5.75 II,III T,C,S,X,IG.8 I,II T,C,S,X,IG.8 III T,C,S,X,IG. I,II T,C,S,X,IG. III T,C,S,X,IG I,II T,C,S,X,IG III T,C,S,X,IG 6 pole motor Standard Motor Types (see page B-10 for product codes) T TEFC, three phase, 08-30/60 or 575 volts C Corro-Duty, three phase, 30/60 or 575 volts S TEFC, single phase, 115/30 volts X Explosionproof, Cls I Grp D, Cls II Grps F&G, three phase, 30/60 or 575 volts IG INTELLIGEAR variable speed for 1/30, 30 or 60V power supplies Overhung loads are at shaft midpoint B-

25 SELECTION TABLES 1/ HP GEARMOTORS General Specifications: Totally enclosed, 60 hertz, 0 C ambient, continuous duty. 1/ HORSEPOWER (continued) Output AGMA Service Output Torque OHL Nominal Frame Size Std. Motor RPM Class Factor in-lb lb Ratio Gear Motor Types 3.5 I T,C,S,X,IG 3.5 II,III T,C,S,X,IG 3 I T,C,S,X,IG 3 II,III T,C,S,X,IG.7 I,II T,C,S,X,IG.7 III T,C,S,X,IG. I,II T,C,S,X,IG. III T,C,S,X,IG. I,II T,C,S,X,IG. III T,C,S,X,IG 1.95 I,II T,C,S,X,IG 1.95 III T,C,S,X,IG 1.75 I T,C,S,X,IG 1.75 II T,C,S,X,IG 1.75 III T,C,S,X,IG 1.5 I T,C,S,X,IG 1.5 II T,C,S,X,IG 1.5 III T,C,S,X,IG 1. I T,C,S,X,IG 1. II,III T,C,S,X,IG.98 I T,C,S,X,IG.98 II T,C,S,X,IG.98 III T,C,S,X,IG.75 I T,C,S,X,IG.75 II,III T,C,S,X,IG.61 I T,C,S,X,IG.61 II,III T,C,S,X,IG.50 I,II T,C,S,X,IG.50 III T,C,S,X,IG.38 I T,C,S,X,IG.38 II,III T,C,S,X,IG.30 I,II T,C,S,X,IG.8 I,II T,C,S,X,IG Standard Motor Types (see page B-10 for product codes) T TEFC, three phase, 08-30/60 or 575 volts C Corro-Duty, three phase, 30/60 or 575 volts S TEFC, single phase, 115/30 volts X Explosionproof, Cls I Grp D, Cls II Grps F&G, three phase, 30/60 or 575 volts IG INTELLIGEAR variable speed for 1/30, 30 or 60V power supplies Overhung loads are at shaft midpoint B-5

26 SELECTION TABLES HP GEARMOTORS General Specifications: Totally enclosed, 60 hertz, 0 C ambient, continuous duty. HORSEPOWER Output AGMA Service Output Torque OHL Nominal Frame Size Std. Motor RPM Class Factor in-lb lb Ratio Gear Motor Types 1 III T,C,S,X,IG 1.3 III T,C,S,X,IG 11.3 II,III T,C,S,X,IG 9.3 II,III T T,C,X 8.3 I,II,III T T,C,X 7.3 I,II T T,C,X 7.3 III T T,C,X 6. I,II T,C,S,X,IG 6. III T,C,S,X,IG 5.75 I,II T,C,S,X,IG 5.75 III T,C,S,X,IG.8 I T,C,S,X,IG.8 II,III T,C,S,X,IG. I T,C,S,X,IG. II,III T,C,S,X,IG I,II T,C,S,X,IG III T,C,S,X,IG 3.5 I,II T,C,S,X,IG 3.5 III T,C,S,X,IG 3 I,II T,C,S,X,IG 6 pole motor Standard Motor Types (see page B-10 for product codes) T TEFC, three phase, 08-30/60 or 575 volts C Corro-Duty, three phase, 30/60 or 575 volts S TEFC, single phase, 115/30 volts X Explosionproof, Cls I Grp D, Cls II Grps F&G, three phase, 30/60 or 575 volts IG INTELLIGEAR variable speed for 1/30, 30 or 60V power supplies Overhung loads are at shaft midpoint B-6

27 SELECTION TABLES HP GEARMOTORS General Specifications: Totally enclosed, 60 hertz, 0 C ambient, continuous duty. HORSEPOWER (continued) Output AGMA Service Output Torque OHL Nominal Frame Size Std. Motor RPM Class Factor in-lb lb Ratio Gear Motor Types 3 III T,C,S,X,IG.7 I T,C,S,X,IG.7 II,III T,C,S,X,IG. I T,C,S,X,IG. II T,C,S,X,IG. III T,C,S,X,IG. I T,C,S,X,IG. II T,C,S,X,IG. III T,C,S,X,IG 1.95 I,II T,C,S,X,IG 1.95 III T,C,S,X,IG 1.75 I T,C,S,X,IG 1.75 II T,C,S,X,IG 1.75 III A 56 T,C,S,X,IG 1.5 I T,C,S,X,IG 1.5 II T,C,S,X,IG 1.5 III A 56 T,C,S,X,IG 1. I,II T,C,S,X,IG 1. III A 56 T,C,S,X,IG.98 I T,C,S,X,IG.98 II,III T,C,S,X,IG.75 I,II T,C,S,X,IG.75 III T,C,S,X,IG.61 I T,C,S,X,IG.61 II,III T,C,S,X,IG.50 I,II T,C,S,X,IG.38 I T,C,S,X,IG.30 I T,C,S,X,IG Standard Motor Types (see page B-10 for product codes) T TEFC, three phase, 08-30/60 or 575 volts C Corro-Duty, three phase, 30/60 or 575 volts S TEFC, single phase, 115/30 volts X Explosionproof, Cls I Grp D, Cls II Grps F&G, three phase, 30/60 or 575 volts IG INTELLIGEAR variable speed for 1/30, 30 or 60V power supplies Overhung loads are at shaft midpoint B-7

28 SELECTION TABLES 1 HP GEARMOTORS General Specifications: Totally enclosed, 60 hertz, 0 C ambient, continuous duty. 1 HORSEPOWER Output AGMA Service Output Torque OHL Nominal Frame Size Std. Motor RPM Class Factor in-lb lb Ratio Gear Motor Types 17.5 III T T,C,S,X,IG 15.6 III T T,C,S,X,IG 1 II,III T T,C,S,X,IG 1.3 II,III T T,C,S,X,IG 11.3 II,III T T,C,S,X,IG 9.75 I,II T T,C,S,X,IG 9.75 III T T,C,S,X,IG 9 I,II T T,C,S,X,IG 9 III T T,C,S,X,IG 8 I,II T T,C,S,X,IG 8 III T T,C,S,X,IG 7 I T T,C,S,X,IG 7 II,III T T,C,S,X,IG 6. I T T,C,S,X,IG 6. II,III T T,C,S,X,IG 5.75 I T T,C,S,X,IG 5.75 II,III T T,C,S,X,IG.8 I,II T T,C,S,X,IG.8 III T T,C,S,X,IG. I,II T T,C,S,X,IG. III T T,C,S,X,IG I,II T T,C,S,X,IG III T T,C,S,X,IG 3.5 I T T,C,S,X,IG 3.5 II T T,C,S,X,IG Standard Motor Types (see page B-10 for product codes) T TEFC, three phase, 08-30/60 or 575 volts C Corro-Duty, three phase, 30/60 or 575 volts S TEFC, single phase, 115/30 volts X Explosionproof, Cls I Grp D, Cls II Grps F&G, three phase, 30/60 or 575 volts IG INTELLIGEAR variable speed for 1/30, 30 or 60V power supplies Overhung loads are at shaft midpoint B-8

29 SELECTION TABLES 1 HP GEARMOTORS General Specifications: Totally enclosed, 60 hertz, 0 C ambient, continuous duty. 1 HORSEPOWER (continued) Output AGMA Service Output Torque OHL Nominal Frame Size Std. Motor RPM Class Factor in-lb lb Ratio Gear Motor Types 3.5 III T T,C,S,X,IG 3 I T T,C,S,X,IG 3 II T T,C,S,X,IG 3 III T T,C,S,X,IG.7 I,II T T,C,S,X,IG.7 III T T,C,S,X,IG. I,II T T,C,S,X,IG. III T T,C,S,X,IG. I T T,C,S,X,IG. II T T,C,S,X,IG. III A 13T T,C,S,X,IG 1.95 I T T,C,S,X,IG 1.95 II T T,C,S,X,IG 1.95 III A 13T T,C,S,X,IG 1.75 I,II T T,C,S,X,IG 1.75 III A 13T T,C,S,X,IG 1.5 I T T,C,S,X,IG 1.5 II,III A 13T T,C,S,X,IG 1. I T T,C,S,X,IG 1. II,III A 13T T,C,S,X,IG.98 I,II T T,C,S,X,IG.98 III T T,C,S,X,IG.75 I T T,C,S,X,IG.75 II,III T T,C,S,X,IG.61 I,II T T,C,S,X,IG.50 I T T,C,S,X,IG Standard Motor Types (see page B-10 for product codes) T TEFC, three phase, 08-30/60 or 575 volts C Corro-Duty, three phase, 30/60 or 575 volts S TEFC, single phase, 115/30 volts X Explosionproof, Cls I Grp D, Cls II Grps F&G, three phase, 30/60 or 575 volts IG INTELLIGEAR variable speed for 1/30, 30 or 60V power supplies Overhung loads are at shaft midpoint B-9

30 1 1/ HP GEARMOTORS SELECTION TABLES General Specifications: Totally enclosed, 60 hertz, 0 C ambient, continuous duty. 1 1/ HORSEPOWER Output AGMA Service Output Torque OHL Nominal Frame Size Std. Motor RPM Class Factor in-lb lb Ratio Gear Motor Types 8 III T T,C,S,X,IG 5 III T T,C,S,X,IG III T T,C,S,X,IG 19.8 II,III T T,C,S,X,IG 17.5 II,III T T,C,S,X,IG 15.7 II T T,C,S,X,IG 15.7 III T T,C,S,X,IG 1.1 I,II T T,C,S,X,IG 1.1 III T T,C,S,X,IG 1. I,II T T,C,S,X,IG 1. III T T,C,S,X,IG 11.1 I,ll T T,C,S,X,IG 11.1 III T T,C,S,X,IG 9.75 I T T,C,S,X,IG 9.75 II,III T T,C,S,X,IG Standard Motor Types (see page B-10 for product codes) T TEFC, three phase, 08-30/60 or 575 volts C Corro-Duty, three phase, 30/60 or 575 volts S TEFC, single phase, 115/30 volts, 15TY X Explosionproof, Cls I Grp D, Cls II Grps F&G, three phase, 30/60 or 575 volts IG INTELLIGEAR variable speed for 1/30, 30 or 60V power supplies Overhung loads are at shaft midpoint B-30

31 SELECTION TABLES 1 1/ HP GEARMOTORS General Specifications: Totally enclosed, 60 hertz, 0 C ambient, continuous duty. 1 1/ HORSEPOWER (continued) Output AGMA Service Output Torque OHL Nominal Frame Size Std. Motor RPM Class Factor in-lb lb Ratio Gear Motor Types 9 I T T,C,S,X,IG 9 II,III T T,C,S,X,IG 8 I,II T T,C,S,X,IG 8 III T T,C,S,X,IG 7 I,II T T,C,S,X,IG 7 III T T,C,S,X,IG 6. I,II T T,C,S,X,IG 6. III T T,C,S,X,IG 5.75 I T T,C,S,X,IG 5.75 II,III T T,C,S,X,IG.8 I T T,C,S,X,IG.8 II T T,C,S,X,IG.8 III T T,C,S,X,IG. I,II T T,C,S,X,IG. III T T,C,S,X,IG I,II T T,C,S,X,IG III T T,C,S,X,IG 3.5 I T T,C,S,X,IG 3.5 II T T,C,S,X,IG 3 I T T,C,S,X,IG 3 II T T,C,S,X,IG 3 III A 15T T,C,S,X,IG.7 I,II T T,C,S,X,IG.7 III A 15T T,C,S,X,IG. I,II T T,C,S,X,IG. III A 15T T,C,S,X,IG. I T T,C,S,X,IG. II,III A 15T T,C,S,X,IG 1.95 I T T,C,S,X,IG 1.95 II,III A 15T T,C,S,X,IG 1.75 I,II A 15T T,C,S,X,IG 1.75 III T T,C,S,X,IG 1.5 I,II A 15T T,C,S,X,IG 1.5 III T T,C,S,X,IG 1. I A 15T T,C,S,X,IG 1. II,III T T,C,S,X,IG.98 I,II T T,C,S,X,IG.61 I T T,C,S,X,IG Standard Motor Types (see page B-10 for product codes) T TEFC, three phase, 08-30/60 or 575 volts C Corro-Duty, three phase, 30/60 or 575 volts S TEFC, single phase, 115/30 volts, 15TY X Explosionproof, Cls I Grp D, Cls II Grps F&G, three phase, 30/60 or 575 volts IG INTELLIGEAR variable speed for 1/30, 30 or 60V power supplies Overhung loads are at shaft midpoint B-31

32 SELECTION TABLES HP GEARMOTORS General Specifications: Totally enclosed, 60 hertz, 0 C ambient, continuous duty. HORSEPOWER Output AGMA Service Output Torque OHL Nominal Frame Size Std. Motor RPM Class Factor in-lb lb Ratio Gear Motor Types 39 III T T,C,S,X,IG 35 III T T,C,S,X,IG 31 III T T,C,S,X,IG 8 II,III T T,C,S,X,IG 5 II,III T T,C,S,X,IG II,III T T,C,S,X,IG 0 I,II T T,C,S,X,IG 0 III T T,C,S,X,IG 17.7 I,II T T,C,S,X,IG 17.7 III T T,C,S,X,IG 15.8 I,II T T,C,S,X,IG 15.8 III T T,C,S,X,IG 1.1 I T T,C,S,X,IG 1.1 II,III T T,C,S,X,IG 1.1 I T T,C,S,X,IG 1.1 II,III T T,C,S,X,IG Standard Motor Types (see page B-10 for product codes) T TEFC, three phase, 08-30/60 or 575 volts C Corro-Duty, three phase, 30/60 or 575 volts S TEFC, single phase, 115/30 volts, 15TY X Explosionproof, Cls I Grp D, Cls II Grps F&G, three phase, 30/60 or 575 volts IG INTELLIGEAR variable speed for 1/30, 30 or 60V power supplies, 15TY frame motor Overhung loads are at shaft midpoint B-3

33 SELECTION TABLES HP GEARMOTORS General Specifications: Totally enclosed, 60 hertz, 0 C ambient, continuous duty. HORSEPOWER (continued) Output AGMA Service Output Torque OHL Nominal Frame Size Std. Motor RPM Class Factor in-lb lb Ratio Gear Motor Types 11.1 I T T,C,S,X 11.1 I,II,III T T,C,S,X 9.75 I,II T T,C,S,X 9.75 III T T,C,S,X 9 I,II T T,C,S,X 9 III T T,C,S,X 8 I,II T T,C,S,X 8 III T T,C,S,X 7 I T T,C,S,X 7 II T T,C,S,X 7 III T T,C,S,X 6. I T T,C,S,X 6. II T T,C,S,X 6. III T T,C,S,X 5.75 I,II T T,C,S,X 5.75 III T T,C,S,X.8 I T T,C,S,X.8 II,III T T,C,S,X. I T T,C,S,X. II T T,C,S,X. III A 15T T,C,S,X I T T,C,S,X II T T,C,S,X III A 15T T,C,S,X 3.5 I,II T T,C,S,X 3.5 III A 15T T,C,S,X 3 I T T,C,S,X 3 II,III A 15T T,C,S,X.7 I T T,C,S,X.7 II,III A 15T T,C,S,X. I T T,C,S,X. II A 15T T,C,S,X. III T T,C,S,X. I,II A 15T T,C,S,X. III T T,C,S,X 1.95 I,II A 15T T,C,S,X 1.95 III T T,C,S,X Standard Motor Types (see page B-10 for product codes) T TEFC, three phase, 08-30/60 or 575 volts C Corro-Duty, three phase, 30/60 or 575 volts S TEFC, single phase, 115/30 volts, 15TY X Explosionproof, Cls I Grp D, Cls II Grps F&G, three phase, 30/60 or 575 volts IG INTELLIGEAR variable speed for 1/30, 30 or 60V power supplies, 15TY Overhung loads are at shaft midpoint B-33

34 SELECTION TABLES HP GEARMOTORS General Specifications: Totally enclosed, 60 hertz, 0 C ambient, continuous duty. HORSEPOWER (continued) Output AGMA Service Output Torque OHL Nominal Frame Size Std. Motor RPM Class Factor in-lb lb Ratio Gear Motor Types 1.5 I A 15T T,C,S,X,IG 1.5 II T T,C,S,X,IG 1. I,II T T,C,S,X,IG.98 I T T,C,S,X,IG Standard Motor Types (see page B-10 for product codes) T TEFC, three phase, 08-30/60 or 575 volts C Corro-Duty, three phase, 30/60 or 575 volts S TEFC, single phase, 115/30 volts, 15TY X Explosionproof, Cls I Grp D, Cls II Grps F&G, three phase, 30/60 or 575 volts IG INTELLIGEAR variable speed for 1/30, 30 or 60V power supplies, 15TY Overhung loads are at shaft midpoint B-3

35 SELECTION TABLES 1/ HP GEARMOTORS General Specifications: Totally enclosed, 60 hertz, 0 C ambient, continuous duty. 1/ HORSEPOWER Output AGMA Service Output Torque OHL Nominal Frame Size Std. Motor RPM Class Factor in-lb lb Ratio Gear Motor Types 9 III TY T,C III TY T,C 39 III TY T,C 35 II,III TY T,C 31 II,III TY T,C 8 II,III TY T,C 5 I,II TY T,C 5 III TY T,C I,II TY T,C III TY T,C 0 I,II TY T,C Standard Motor Types (see page B-10 for product codes) T TEFC, three phase, 08-30/60 or 575 volts C Corro-Duty, three phase, 30/60 or 575 volts Overhung loads are at shaft midpoint B-35

36 SELECTION TABLES 1/ HP GEARMOTORS General Specifications: Totally enclosed, 60 hertz, 0 C ambient, continuous duty. 1/ HORSEPOWER (continued) Output AGMA Service Output Torque OHL Nominal Frame Size Std. Motor RPM Class Factor in-lb lb Ratio Gear Motor Types 0 III TY T,C 17.7 I TY T,C 17.7 II,III TY T,C 15.8 I TY T,C 15.8 II,III TY T,C 1.1 I TY T,C 1.1 II,III TY T,C 1.8 I,II TY T,C 1.8 III TY T,C 11.1 I,II TY T,C 9.75 I,II TY T,C 9.75 III TY T,C 9 I TY T,C 9 II TY T,C 9 III TY T,C 8 I TY T,C 8 II TY T,C 8 III TY T,C 7 I,II TY T,C 7 III TY T,C 6. I TY T,C 6. II,III TY T,C 5.75 I TY T,C 5.75 II TY T,C 5.75 III A 15TY T,C.8 I TY T,C.8 II TY T,C.8 III A 15TY T,C. I,II TY T,C. III A 15TY T,C I TY T,C II,III A 15TY T,C 3.5 I TY T,C 3.5 II,III A 15TY T,C 3 I TY T,C 3 II A 15TY T,C 3 III TY T,C.7 I,II A 15TY T,C Standard Motor Types (see page B-10 for product codes) T TEFC, three phase, 08-30/60 or 575 volts C Corro-Duty, three phase, 30/60 or 575 volts Overhung loads are at shaft midpoint B-36

37 SELECTION TABLES 1/ HP GEARMOTORS General Specifications: Totally enclosed, 60 hertz, 0 C ambient, continuous duty. 1/ HORSEPOWER (continued) Output AGMA Service Output Torque OHL Nominal Frame Size Std. Motor RPM Class Factor in-lb lb Ratio Gear Motor Types.7 III TY T,C. I,II A 15TY T,C. III TY T,C. I,II A 15TY T,C. III TY T,C 1.95 I A 15TY T,C 1.95 II TY T,C 1.75 I A 15TY T,C 1.75 II TY T,C 1.5 I,II TY T,C 1. I TY T,C Standard Motor Types (see page B-10 for product codes) T TEFC, three phase, 08-30/60 or 575 volts C Corro-Duty, three phase, 30/60 or 575 volts Overhung loads are at shaft midpoint B-37

38 SELECTION TABLES 3 HP GEARMOTORS General Specifications: Totally enclosed, 60 hertz, 0 C ambient, continuous duty. 3 HORSEPOWER Output AGMA Service Output Torque OHL Nominal Frame Size Std. Motor RPM Class Factor in-lb lb Ratio Gear Motor Types 56 III T T,C,S,X,IG 9 III T T,C,S,X,IG III T T,C,S,X,IG 39 II,III T T,C,S,X,IG 35 II,III T T,C,S,X,IG 31 I,II T T,C,S,X,IG 31 III T T,C,S,X,IG 8 I,II T T,C,S,X,IG 7 III T T,C,S,X,IG 5 I,II T T,C,S,X,IG III T T,C,S,X,IG I,II T T,C,S,X,IG III T T,C,S,X,IG 0.1 I T T,C,S,X,IG 0 II,III T T,C,S,X,IG 17.7 I T T,C,S,X,IG 17.7 II,III T T,C,S,X,IG 16 I,II,III T T,C,S,X,IG 1.1 I,II T T,C,S,X,IG 1.1 III T T,C,S,X,IG 1.8 I,II T T,C,S,X,IG 1.8 III T T,C,S,X,IG 11.1 I,II T T,C,S,X,IG 11 III T T,C,S,X,IG Standard Motor Types (see page B-10 for product codes) T TEFC, three phase, 08-30/60 or 575 volts C Corro-Duty, three phase, 30/60 or 575 volts S TEFC, single phase, 30 volts, 18T X Explosionproof, Cls I Grp D, Cls II Grps F&G, three phase, 30/60 or 575 volts IG INTELLIGEAR variable speed for 60V power supplies Overhung loads are at shaft midpoint B-38

39 SELECTION TABLES 3 HP GEARMOTORS General Specifications: Totally enclosed, 60 hertz, 0 C ambient, continuous duty. 3 HORSEPOWER (continued) Output AGMA Service Output Torque OHL Nominal Frame Size Std. Motor RPM Class Factor in-lb lb Ratio Gear Motor Types 9.75 I T T,C,S,X,IG 9.75 II T T,C,S,X,IG 9.75 III T T,C,S,X,IG 9 I T T,C,S,X,IG 9 II T T,C,S,X,IG 9 III T T,C,S,X,IG 8 I,II T T,C,S,X,IG 8 III T T,C,S,X,IG 7 I T T,C,S,X,IG 7 II T T,C,S,X,IG 7 III A 18T T,C,S,X,IG 6. I T T,C,S,X,IG 6. II T T,C,S,X,IG 6. III A 18T T,C,S,X,IG 5.75 I,II T T,C,S,X,IG 5.75 III A 18T T,C,S,X,IG.8 I,II T T,C,S,X,IG.8 III A 18T T,C,S,X,IG. I T T,C,S,X,IG. II,III A 18T T,C,S,X,IG I T T,C,S,X,IG II,III A 18T T,C,S,X,IG 3.5 I,II A 18T T,C,S,X,IG 3.5 III T T,C,S,X,IG 3 I,II A 18T T,C,S,X,IG 3 III T T,C,S,X,IG.7 I,II A 18T T,C,S,X,IG.7 III T T,C,S,X,IG. I A 18T T,C,S,X,IG. II,III T T,C,S,X,IG. I A 18T T,C,S,X,IG. II,III T T,C,S,X,IG 1.95 I A 18T T,C,S,X,IG 1.95 II T T,C,S,X,IG 1.75 I,II T T,C,S,X,IG 1.5 I T T,C,S,X,IG 1. I T T,C,S,X,IG Standard Motor Types (see page B-10 for product codes) T TEFC, three phase, 08-30/60 or 575 volts C Corro-Duty, three phase, 30/60 or 575 volts S TEFC, single phase, 30 volts, 18T X Explosionproof, Cls I Grp D, Cls II Grps F&G, three phase, 30/60 or 575 volts IG INTELLIGEAR variable speed for 60V power supplies Overhung loads are at shaft midpoint B-39

40 SELECTION TABLES 5 HP GEARMOTORS General Specifications: Totally enclosed, 60 hertz, 0 C ambient, continuous duty. 5 HORSEPOWER Output AGMA Service Output Torque OHL Nominal Frame Size Std. Motor RPM Class Factor in-lb lb Ratio Gear Motor Types 100 III T T,C,S,X,IG 88 III T T,C,S,X,IG 79 III T T,C,S,X,IG 70 II,III T T,C,S,X,IG 61 II,III T T,C,S,X,IG 56 II,III T T,C,S,X,IG 9 I,ll T T,C,S,X,IG 9 III T T,C,S,X,IG I,II T T,C,S,X,IG III T T,C,S,X,IG 39 I,II T T,C,S,X,IG 39 III T T,C,S,X,IG 36 I T T,C,S,X,IG 35 II,III T T,C,S,X,IG 31 I T T,C,S,X,IG 31 II,III T T,C,S,X,IG 8 I T T,C,S,X,IG 7 I,II T T,C,S,X,IG 7 III T T,C,S,X,IG I,II T T,C,S,X,IG III T T,C,S,X,IG I,II T T,C,S,X,IG III T T,C,S,X,IG 0 I,II T T,C,S,X,IG Standard Motor Types (see page B-10 for product codes) T TEFC, three phase, 08-30/60 or 575 volts C Corro-Duty, three phase, 30/60 or 575 volts S TEFC, single phase, 30 volts X Explosionproof, Cls I Grp D, Cls II Grps F&G, three phase, 30/60 or 575 volts IG INTELLIGEAR variable speed for 60V power supplies Overhung loads are at shaft midpoint B-0

41 SELECTION TABLES 5 HP GEARMOTORS General Specifications: Totally enclosed, 60 hertz, 0 C ambient, continuous duty. 5 HORSEPOWER (continued) Output AGMA Service Output Torque OHL Nominal Frame Size Std. Motor RPM Class Factor in-lb lb Ratio Gear Motor Types 0 III T T,C,S,X,IG 17.7 I T T,C,S,X,IG 17.7 II,III T T,C,S,X,IG 16.1 I T T,C,S,X,IG 16.1 II T T,C,S,X,IG 16.1 III T T,C,S,X,IG 1.1 I T T,C,S,X,IG 1.1 II T T,C,S,X,IG 1.1 III T T,C,S,X,IG 1.8 I,II T T,C,S,X,IG 1.8 III T T,C,S,X,IG 11 I T T,C,S,X,IG 11 II T T,C,S,X,IG 9.75 I T T,C,S,X,IG 9.75 II T T,C,S,X,IG 9.75 III A 18T T,C,S,X,IG 9 I,II T T,C,S,X,IG 9 III A 18T T,C,S,X,IG 8 I T T,C,S,X,IG 8 II,III A 18T T,C,S,X,IG 7 I T T,C,S,X,IG 7 II,III A 18T T,C,S,X,IG 6. I T T,C,S,X,IG 6. II A 18T T,C,S,X,IG 6. III T T,C,S,X,IG 5.75 I,II A 18T T,C,S,X,IG 5.75 III T T,C,S,X,IG.8 I,II A 18T T,C,S,X,IG.8 III T T,C,S,X,IG. I,II A 18T T,C,S,X,IG. III T T,C,S,X,IG I A 18T T,C,S,X,IG II T T,C,S,X,IG 3.5 I A 18T T,C,S,X,IG 3.5 II T T,C,S,X,IG 3 I,II T T,C,S,X,IG.7 I,II T T,C,S,X,IG Standard Motor Types (see page B-10 for product codes) T TEFC, three phase, 08-30/60 or 575 volts C Corro-Duty, three phase, 30/60 or 575 volts S TEFC, single phase, 30 volts X Explosionproof, Cls I Grp D, Cls II Grps F&G, three phase, 30/60 or 575 volts IG INTELLIGEAR variable speed for 60V power supplies Overhung loads are at shaft midpoint B-1

42 SELECTION TABLES 7 1/ HP GEARMOTORS General Specifications: Totally enclosed, 60 hertz, 0 C ambient, continuous duty. 7 1/ HORSEPOWER Output AGMA Service Output Torque OHL Nominal Frame Size Std. Motor RPM Class Factor in-lb lb Ratio Gear Motor Types 557 II,III T T,C,X 501 II,III T T,C,X 0 II,III T T,C,X 315 I,II T T,C,X 315 III T T,C,X 15 III T T,C,X 10 III T T,C,X 1 III T T,C,X 111 II,III T T,C,X Standard Motor Types (see page B-10 for product codes) T TEFC, three phase, 08-30/60 or 575 volts C Corro-Duty, three phase, 30/60 or 575 volts X Explosionproof, Cls I Grp D, Cls II Grps F&G, three phase, 30/60 or 575 volts Overhung loads are at shaft midpoint B-

43 SELECTION TABLES 7 1/ HP GEARMOTORS General Specifications: Totally enclosed, 60 hertz, 0 C ambient, continuous duty. 7 1/ HORSEPOWER (continued) Output AGMA Service Output Torque OHL Nominal Frame Size Std. Motor RPM Class Factor in-lb lb Ratio Gear Motor Types 100 II,III T T,C,X 88 II,III T T,C,X 79 I,II T T,C,X 79 III T T,C,X 70 I,II T T,C,X 70 III T T,C,X 6 I,II T T,C,X 6 III T T,C,X 56 I T T,C,X 55 II,III T T,C,X 50 I,II,III T T,C,X I,II,III T T,C,X 39 I,II T T,C,X 39 III T T,C,X 35 I,II T T,C,X 35 III T T,C,X 3 I,II T T,C,X 3 III T T,C,X 7 I T T,C,X 7 II,III T T,C,X I T T,C,X II T T,C,X III T T,C,X I T T,C,X II T T,C,X III T T,C,X 0 I,II T T,C,X 0 III T T,C,X 17.7 I T T,C,X 17.7 II,III T T,C,X 16.1 I T T,C,X 16.1 II T T,C,X 16.1 III T T,C,X Standard Motor Types (see page B-10 for product codes) T TEFC, three phase, 08-30/60 or 575 volts C Corro-Duty, three phase, 30/60 or 575 volts X Explosionproof, Cls I Grp D, Cls II Grps F&G, three phase, 30/60 or 575 volts Overhung loads are at shaft midpoint B-3

44 SELECTION TABLES 7 1/ HP GEARMOTORS General Specifications: Totally enclosed, 60 hertz, 0 C ambient, continuous duty. 7 1/ HORSEPOWER (continued) Output AGMA Service Output Torque OHL Nominal Frame Size Std. Motor RPM Class Factor in-lb lb Ratio Gear Motor Types 1.1 I T T,C,X 1.1 I,II T T,C,X 13.7 III T T,C,X 1.8 I,II T T,C,X 11.6 I,II,III T T,C,X 11 I T T,C,X 10.6 I,II,III T T,C,X 9.75 I T T,C,X 9.75 II A 13T T,C,X 9 I,II A 13T T,C,X 9 III T T,C,X 8 I,II A 13T T,C,X 8 III T T,C,X 7 I,II A 13T T,C,X 7 III T T,C,X 6. I A 13T T,C,X 6. II,III T T,C,X 5.75 I A 13T T,C,X 5.75 II T T,C,X.8 I,II T T,C,X. I,II T T,C,X I,II T T,C,X 3.5 I T T,C,X 3 I T T,C,X 6 pole motor Standard Motor Types (see page B-10 for product codes) T TEFC, three phase, 08-30/60 or 575 volts C Corro-Duty, three phase, 30/60 or 575 volts X Explosionproof, Cls I Grp D, Cls II Grps F&G, three phase, 30/60 or 575 volts Overhung loads are at shaft midpoint B-

45 SELECTION TABLES 10 HP GEARMOTORS General Specifications: Totally enclosed, 60 hertz, 0 C ambient, continuous duty. 10 HORSEPOWER Output AGMA Service Output Torque OHL Nominal Frame Size Std. Motor RPM Class Factor in-lb lb Ratio Gear Motor Types 15 III T T,C,X 1389 III T T,C,X 13 III T T,C,X 107 III T T,C,X 991 III T T,C,X 875 III T T,C,X 781 III T T,C,X 700 II,III T T,C,X 61 II,III T T,C,X 561 I,II,III T T,C,X 506 I,II T T,C,X 87 III T T,C,X 0 III T T,C,X 0 I,II T T,C,X 00 III T T,C,X 338 III T T,C,X 315 I,II T T,C,X 315 III T T,C,X 70 III T T,C,X 5 III T T,C,X 1 III T T,C,X Standard Motor Types (see page B-10 for product codes) T TEFC, three phase, 08-30/60 or 575 volts C Corro-Duty, three phase, 30/60 or 575 volts X Explosionproof, Cls I Grp D, Cls II Grps F&G, three phase, 30/60 or 575 volts Overhung loads are at shaft midpoint B-5

46 SELECTION TABLES 10 HP GEARMOTORS General Specifications: Totally enclosed, 60 hertz, 0 C ambient, continuous duty. 10 HORSEPOWER (continued) Output AGMA Service Output Torque OHL Nominal Frame Size Std. Motor RPM Class Factor in-lb lb Ratio Gear Motor Types 196 III T T,C,X 175 III T T,C,X 15 III T T,C,X 10 ll,iii T T,C,X 1 II,lll T T,C,X 111 I,II T T,C,X 107 lli T T,C,X 100 I,II T T,C,X 96 lli T T,C,X 88 I,II T T,C,X 85 lli T T,C,X 79 I,II T T,C,X 79 III T T,C,X 70 I T T,C,X 70 Il,lII T T,C,X 6 I T T,C,X 6 Il,lII T T,C,X 55 I,II T T,C,X 55 lli T T,C,X 50 I,II T T,C,X 50 III T T,C,X I,II T T,C,X lli T T,C,X 39 I T T,C,X 39 II,lll T T,C,X 35 I T T,C,X 35 II T T,C,X 35 III T T,C,X 3 I T T,C,X 3 II T T,C,X Standard Motor Types (see page B-10 for product codes) T TEFC, three phase, 08-30/60 or 575 volts C Corro-Duty, three phase, 30/60 or 575 volts X Explosionproof, Cls I Grp D, Cls II Grps F&G, three phase, 30/60 or 575 volts Overhung loads are at shaft midpoint B-6

47 SELECTION TABLES 10 HP GEARMOTORS General Specifications: Totally enclosed, 60 hertz, 0 C ambient, continuous duty. 10 HORSEPOWER (continued) Output AGMA Service Output Torque OHL Nominal Frame Size Std. Motor RPM Class Factor in-lb lb Ratio Gear Motor Types 3 III T T,C,X 7 I T T,C,X 7 II T T,C,X 7 III T T,C,X I,II T T,C,X III T T,C,X I T T,C,X II T T,C,X III T T,C,X 0 I T T,C,X 0 II T T,C,X 0 III T T,C,X 17.7 I T T,C,X 17.7 II T T,C,X 17.3 III T T,C,X 16.1 I,II T T,C,X 16.1 III T T,C,X 1.1 I T T,C,X 13.7 II,III T T,C,X 1.8 I T T,C,X 9.75 I,II A 15T T,C,X 9.75 III T T,C,X 9 I A 15T T,C,X 9 II,III T T,C,X 8 I A 15T T,C,X 8 II,III T T,C,X 7 I A 15T T,C,X 7 II T T,C,X 6. I,II T T,C,X 5.75 I,II T T,C,X.8 I T T,C,X. I T T,C,X Standard Motor Types (see page B-10 for product codes) T TEFC, three phase, 08-30/60 or 575 volts C Corro-Duty, three phase, 30/60 or 575 volts X Explosionproof, Cls I Grp D, Cls II Grps F&G, three phase, 30/60 or 575 volts Overhung loads are at shaft midpoint B-7

48 SELECTION TABLES 15 HP GEARMOTORS General Specifications: Totally enclosed, 60 hertz, 0 C ambient, continuous duty. 15 HORSEPOWER Output AGMA Service Output Torque OHL Nominal Frame Size Std. Motor RPM Class Factor in-lb lb Ratio Gear Motor Types 15 I,II,III T T,C,X 1389 I,II,III T T,C,X 13 I,II,III T T,C,X 107 I,II,III T T,C,X 100 I,II,III T T,C,X 888 I,II,III T T,C,X 781 I,II,III T T,C,X 71 I,II,III T T,C,X 630 I,II T T,C,X 630 III T T,C,X 561 I,II T T,C,X 55 II,III T T,C,X 506 I T T,C,X 87 II,III T T,C,X 7 I T T,C,X 0 II,III T T,C,X 00 I T T,C,X 00 II,III T T,C,X 350 I,II,III T T,C,X 3 I,II T T,C,X 30 III T T,C,X 70 I,II,III T T,C,X 8 I,II,III T T,C,X 1 I,II,III T T,C,X 196 I,II,III T T,C,X 175 I,II,III T T,C,X 15 I,II T T,C,X 15 III T T,C,X 11 I,II T T,C,X 139 III T T,C,X 1 I,II T T,C,X Standard Motor Types (see page B-10 for product codes) T TEFC, three phase, 08-30/60 or 575 volts C Corro-Duty, three phase, 30/60 or 575 volts X Explosionproof, Cls I Grp D, Cls II Grps F&G, three phase, 30/60 or 575 volts Overhung loads are at shaft midpoint B-8

49 SELECTION TABLES 15 HP GEARMOTORS General Specifications: Totally enclosed, 60 hertz, 0 C ambient, continuous duty. 15 HORSEPOWER Output AGMA Service Output Torque OHL Nominal Frame Size Std. Motor RPM Class Factor in-lb lb Ratio Gear Motor Types 1 III T T,C,X 111 I T T,C,X 107 II,III T T,C,X 100 I T T,C,X 96 II,III T T,C,X 88 I T T,C,X 88 II T T,C,X 85 III T T,C,X 79 I,II T T,C,X 79 III T T,C,X 70 I,II T T,C,X 70 III T T,C,X 63 I,II T T,C,X 63 III T T,C,X 55 I T T,C,X 55 II,III T T,C,X 51 I T T,C,X 51 II T T,C,X 51 III T T,C,X I T T,C,X II T T,C,X III T T,C,X 39 I,II T T,C,X 39 III T T,C,X 35 I T T,C,X 35 II,III T T,C,X 3 I T T,C,X 3 II T T,C,X 3 III T T,C,X 8 I T T,C,X 8 II T T,C,X 8 III T T,C,X I,II T T,C,X III T T,C,X I T T,C,X II,III T T,C,X Standard Motor Types (see page B-10 for product codes) T TEFC, three phase, 08-30/60 or 575 volts C Corro-Duty, three phase, 30/60 or 575 volts X Explosionproof, Cls I Grp D, Cls II Grps F&G, three phase, 30/60 or 575 volts Overhung loads are at shaft midpoint B-9

50 SELECTION TABLES 15 HP GEARMOTORS General Specifications: Totally enclosed, 60 hertz, 0 C ambient, continuous duty. 15 HORSEPOWER (continued) Output AGMA Service Output Torque OHL Nominal Frame Size Std. Motor RPM Class Factor in-lb lb Ratio Gear Motor Types 0 I T T,C,X 0 II,III T T,C,X 17.7 I T,C,X 17.3 II T T,C,X 17.3 III T T,C,X 16.1 I,II T T,C,X 16.1 III T T,C,X 13.7 I,II T T,C,X 13.7 III T T,C,X 9.75 I,II T T,C,X 9 I T T,C,X 8 I T T,C,X 7 I T T,C,X 6. I T T,C,X Standard Motor Types (see page B-10 for product codes) T TEFC, three phase, 08-30/60 or 575 volts C Corro-Duty, three phase, 30/60 or 575 volts X Explosionproof, Cls I Grp D, Cls II Grps F&G, three phase, 30/60 or 575 volts Overhung loads are at shaft midpoint B-50

51 SELECTION TABLES 0 HP GEARMOTORS General Specifications: Totally enclosed, 60 hertz, 0 C ambient, continuous duty. 0 HORSEPOWER Output AGMA Service Output Torque OHL Nominal Frame Size Std. Motor RPM Class Factor in-lb lb Ratio Gear Motor Types 15 I,II T T,C,X 15 III T T,C,X 1389 I,II T T,C,X 1389 III T T,C,X 13 I,II T T,C,X 13 III T T,C,X 1088 I,II T T,C,X 1088 III T T,C,X 100 I,II T T,C,X 100 III T T,C,X 888 I,ll T T,C,X 888 III T T,C,X 781 I,II T T,C,X 77 III T T,C,X 71 I,II T T,C,X 706 III T T,C,X 639 I,II,III T T,C,X 60 I T T,C,X 560 I T T,C,X 55 II,III T T,C,X 87 I,II T T,C,X 87 III T T,C,X 38 I,II T T,C,X 38 III T T,C,X 00 I,II T T,C,X 388 III T T,C,X 350 I,II T T,C,X 350 III T T,C,X 3 I,II T T,C,X 30 III T T,C,X 70 I,II T T,C,X 70 III T T,C,X 8 I,II T T,C,X 6 III T T,C,X 1 I,II T T,C,X 1 III T T,C,X Standard Motor Types (see page B-10 for product codes) T TEFC, three phase, 08-30/60 or 575 volts C Corro-Duty, three phase, 30/60 or 575 volts X Explosionproof, Cls I Grp D, Cls II Grps F&G, three phase, 30/60 or 575 volts Overhung loads are at shaft midpoint B-51

52 SELECTION TABLES 0 HP GEARMOTORS General Specifications: Totally enclosed, 60 hertz, 0 C ambient, continuous duty. 0 HORSEPOWER (continued) Output AGMA Service Output Torque OHL Nominal Frame Size Std. Motor RPM Class Factor in-lb lb Ratio Gear Motor Types 198 I,II T T,C,X 198 III T T,C,X 175 I,II T T,C,X 175 III T T,C,X 15 I T T,C,X 15 II,III T T,C,X 11 I T T,C,X 139 II,III T T,C,X 16 I T T,C,X 16 I,II,III T T,C,X 107 I,II T T,C,X 107 III T T,C,X 96 I,II T T,C,X 96 III T T,C,X 85 I,ll T T,C,X 85 III T T,C,X 79 I T T,C,X 79 II,lll T T,C,X 70 I T T,C,X 70 II T T,C,X 68 III T T,C,X 63 I T T,C,X 63 II T T,C,X 63 III T T,C,X 55 I,II T T,C,X 5 III T T,C,X 51 I T T,C,X 51 II T T,C,X 9 III T T,C,X I T T,C,X 3 II T T,C,X 3 III T T,C,X 39 I T T,C,X 39 II T T,C,X 39 III T T,C,X 35 I,II T T,C,X 35 III T T,C,X 31 I,II T T,C,X Standard Motor Types (see page B-10 for product codes) T TEFC, three phase, 08-30/60 or 575 volts C Corro-Duty, three phase, 30/60 or 575 volts X Explosionproof, Cls I Grp D, Cls II Grps F&G, three phase, 30/60 or 575 volts Overhung loads are at shaft midpoint B-5

53 SELECTION TABLES 0 HP GEARMOTORS General Specifications: Totally enclosed, 60 hertz, 0 C ambient, continuous duty. 0 HORSEPOWER (continued) Output AGMA Service Output Torque OHL Nominal Frame Size Std. Motor RPM Class Factor in-lb lb Ratio Gear Motor Types 31 III T T,C,X 8 I T T,C,X 8 II,lll T T,C,X I T T,C,X II T T,C,X III T T,C,X I,II T T,C,X III T T,C,X 0 I,II T T,C,X 0 III T T,C,X 17.3 I,II T T,C,X 17.3 III T T,C,X 16.1 I T T,C,X 16.1 II,III T T,C,X 13.7 I T T,C,X 13.7 II T T,C,X 9.75 I T T,C,X 9 I T T,C,X Standard Motor Types (see page B-10 for product codes) T TEFC, three phase, 08-30/60 or 575 volts C Corro-Duty, three phase, 30/60 or 575 volts X Explosionproof, Cls I Grp D, Cls II Grps F&G, three phase, 30/60 or 575 volts Overhung loads are at shaft midpoint B-53

54 SELECTION TABLES 5 HP GEARMOTORS General Specifications: Totally enclosed, 60 hertz, 0 C ambient, continuous duty. 5 HORSEPOWER Output AGMA Service Output Torque OHL Nominal Frame Size Std. Motor RPM Class Factor in-lb lb Ratio Gear Motor Types 15 I,II,III A8T T,C,X 1389 I,II,III A8T T,C,X 13 I,II,III A8T T,C,X 1101 I,II,III A8T T,C,X 101 I,II,III A8T T,C,X 888 I,II,III A8T T,C,X 77 I,II,III A8T T,C,X 706 I,II A8T T,C,X 639 I,II A8T T,C,X 55 I,II A8T T,C,X 55 III A8T T,C,X 87 I A8T T,C,X 87 II,III A8T T,C,X 3 I A8T T,C,X 3 II,III A8T T,C,X 00 I,II A8T T,C,X 381 I,II,III A8T T,C,X 35 I,II A8T T,C,X 35 III A8T T,C,X 318 I A8T T,C,X 318 II,III A8T T,C,X 77 I,II,III A8T T,C,X 6 I,II,III A8T T,C,X 17 I,II,III A8T T,C,X 00 I,II,III A8T T,C,X 175 I,II,III A8T T,C,X 15 I,II,III A8T T,C,X 139 I,II A8T T,C,X 139 III A8T T,C,X 16 I,II A8T T,C,X 16 III A8T T,C,X 107 I,II A8T T,C,X 107 III A8T T,C,X 96 I A8T T,C,X 96 II,lll A8T T,C,X 85 I A8T T,C,X Standard Motor Types (see page B-10 for product codes) T TEFC, three phase, 08-30/60 or 575 volts C Corro-Duty, three phase, 30/60 or 575 volts X Explosionproof, Cls I Grp D, Cls II Grps F&G, three phase, 30/60 or 575 volts Overhung loads are at shaft midpoint B-5

55 SELECTION TABLES 5 HP GEARMOTORS General Specifications: Totally enclosed, 60 hertz, 0 C ambient, continuous duty. 5 HORSEPOWER (continued) Output AGMA Service Output Torque OHL Nominal Frame Size Std. Motor RPM Class Factor in-lb lb Ratio Gear Motor Types 85 II A8T T,C,X 85 III A8T T,C,X 79 I,II A8T T,C,X 78 III A8T T,C,X 70 I,II A8T T,C,X 68 III A8T T,C,X 63 I A8T T,C,X 63 II,lll A8T T,C,X 55 I A8T T,C,X 55 II A8T T,C,X 55 III A8T T,C,X 51 I A8T T,C,X 51 II A8T T,C,X 9 III A8T T,C,X I,II A8T T,C,X 3 II,III A8T T,C,X 39 I A8T T,C,X 39 II,III A8T T,C,X 35 I,II,lll A8T T,C,X 35 III A8T T,C,X 3 III A8T T,C,X 8 I,II A8T T,C,X 8 III A8T T,C,X I,II A8T T,C,X III A8T T,C,X I,II A8T T,C,X III A8T T,C,X 0 I A8T T,C,X 0 II A8T T,C,X 17.3 I A8T T,C,X 17.3 II A8T T,C,X 16.1 I,II A8T T,C,X 13.7 I,II A8T T,C,X Standard Motor Types (see page B-10 for product codes) T TEFC, three phase, 08-30/60 or 575 volts C Corro-Duty, three phase, 30/60 or 575 volts X Explosionproof, Cls I Grp D, Cls II Grps F&G, three phase, 30/60 or 575 volts Overhung loads are at shaft midpoint B-55

56 SELECTION TABLES 30 HP GEARMOTORS General Specifications: Totally enclosed, 60 hertz, 0 C ambient, continuous duty. 30 HORSEPOWER Output AGMA Service Output Torque OHL Nominal Frame Size Std. Motor RPM Class Factor in-lb lb Ratio Gear Motor Types 15 I,II,III A86T T,C,X 1389 I,II,III A86T T,C,X 13 I,II,III A86T T,C,X 1101 I,II A86T T,C,X 101 I,II A86T T,C,X 888 I,II A86T T,C,X 77 I,II A86T T,C,X 706 I,II A86T T,C,X 639 I,II A86T T,C,X 55 I,II A86T T,C,X 55 III A86T T,C,X 87 I A86T T,C,X 87 II,III A86T T,C,X 8 I,II,III A86T T,C,X 00 I A86T T,C,X 381 I,II,III A86T T,C,X 35 I,II,III A86T T,C,X 30 I,II A86T T,C,X 77 I,II,III A86T T,C,X 6 I,II,III A86T T,C,X 17 I,II,III A86T T,C,X 00 I,II,III A86T T,C,X 175 I,II A86T T,C,X 175 III A86T T,C,X 15 I,II A86T T,C,X 15 III A86T T,C,X 139 I,II A86T T,C,X 139 III A86T T,C,X 16 I,II A86T T,C,X 16 III A86T T,C,X 108 I A86T T,C,X 108 II A86T T,C,X 108 III A86T T,C,X Standard Motor Types (see page B-10 for product codes) T TEFC, three phase, 08-30/60 or 575 volts C Corro-Duty, three phase, 30/60 or 575 volts X Explosionproof, Cls I Grp D, Cls II Grps F&G, three phase, 30/60 or 575 volts Overhung loads are at shaft midpoint B-56

57 SELECTION TABLES 30 HP GEARMOTORS General Specifications: Totally enclosed, 60 hertz, 0 C ambient, continuous duty. 30 HORSEPOWER (continued) Output AGMA Service Output Torque OHL Nominal Frame Size Std. Motor RPM Class Factor in-lb lb Ratio Gear Motor Types 96 I A86T T,C,X 96 II A86T T,C,X 95 III A86T T,C,X 85 I,II A86T T,C,X 85 III A86T T,C,X 79 I,II A86T T,C,X 78 III A86T T,C,X 70 I A86T T,C,X 70 II A86T T,C,X 70 III A86T T,C,X 63 I A86T T,C,X 63 II A86T T,C,X 61 III A86T T,C,X 55 I,II A86T T,C,X 55 III A86T T,C,X 51 I A86T T,C,X 9 II,III A86T T,C,X I A86T T,C,X 3 II,III A86T T,C,X 39 I A86T T,C,X 39 II,III A86T T,C,X 35 I A86T T,C,X 35 II A86T T,C,X 35 III A86T T,C,X 3 I,II A86T T,C,X 3 III A86T T,C,X 8 I,II A86T T,C,X 8 III A86T T,C,X I A86T T,C,X II,III A86T T,C,X I A86T T,C,X II A86T T,C,X 0 I,II A86T T,C,X 17.3 I,II A86T T,C,X 16.1 I,II A86T T,C,X 13.7 I A86T T,C,X Standard Motor Types (see page B-10 for product codes) T TEFC, three phase, 08-30/60 or 575 volts C Corro-Duty, three phase, 30/60 or 575 volts X Explosionproof, Cls I Grp D, Cls II Grps F&G, three phase, 30/60 or 575 volts Overhung loads are at shaft midpoint B-57

58 SELECTION TABLES 0 HP GEARMOTORS General Specifications: Totally enclosed, 60 hertz, 0 C ambient, continuous duty. 0 HORSEPOWER Output AGMA Service Output Torque OHL Nominal Frame Size Std. Motor RPM Class Factor in-lb lb Ratio Gear Motor Types 55 I,II,III T T,C,X 89 I,II,III T T,C,X 3 I,II,III T T,C,X 381 I,II T T,C,X 38 I,II T T,C,X 38 III T T,C,X 30 I,II T T,C,X 77 I,II,III T T,C,X 6 I,II,III T T,C,X 17 I,II,III T T,C,X 191 I,II,III T T,C,X 175 I,II,III T T,C,X 15 I,II T T,C,X 15 III T,C,X 10 I,II T T,C,X 10 III T T,C,X 16 I,II T T,C,X 16 III T T,C,X 108 I,II T T,C,X 108 III T T,C,X 97 I T T,C,X 97 II T T,C,X 97 III A 3T T,C,X 86 I T T,C,X 86 II T T,C,X 78 I T T,C,X 78 II T T,C,X 78 III T T,C,X 69 I,II T T,C,X 69 III T T,C,X 61 I T T,C,X 61 II,III T T,C,X 55 I T T,C,X 55 II,III T T,C,X 9 I,II T T,C,X 9 III T T,C,X 3 I,II T T,C,X 3 III T T,C,X 39 I,II T T,C,X 39 III T T,C,X 36 I,II T T,C,X B-58 Standard Motor Types (see page B-8 for product codes) T TEFC, three phase, 08-30/60 or 575 volts C Corro-Duty, three phase, 30/60 or 575 volts X Explosionproof, Cls I Grp D, Cls II Grps F&G, three phase, 30/60 or 575 volts Overhung loads are at shaft midpoint

59 SELECTION TABLES 0 HP GEARMOTORS General Specifications: Totally enclosed, 60 hertz, 0 C ambient, continuous duty. 0 HORSEPOWER (continued) Output AGMA Service Output Torque OHL Nominal Frame Size Std. Motor RPM Class Factor in-lb lb Ratio Gear Motor Types 36 II,III T T,C,X 3 I T T,C,X 3 II,III T T,C,X 8 I,II T T,C,X I,II T T,C,X I,II T T,C,X Standard Motor Types (see page B-10 for product codes) T TEFC, three phase, 08-30/60 or 575 volts C Corro-Duty, three phase, 30/60 or 575 volts X Explosionproof, Cls I Grp D, Cls II Grps F&G, three phase, 30/60 or 575 volts Overhung loads are at shaft midpoint B-59

60 SELECTION TABLES 50 HP GEARMOTORS General Specifications: Totally enclosed, 60 hertz, 0 C ambient, continuous duty. 50 HORSEPOWER Output AGMA Service Output Torque OHL Nominal Frame Size Std. Motor RPM Class Factor in-lb lb Ratio Gear Motor Types 55 I,II,III T T,C,X 89 I,II T T,C,X 3 I,II T T,C,X 381 I,II T T,C,X 38 I T T,C,X 38 II,III T T,C,X 30 I T T,C,X 77 I,II,III T T,C,X 6 I,II,III T T,C,X 17 I,II,III T T,C,X 193 I,II T T,C,X 193 III T T,C,X 175 I,II T T,C,X 170 III T T,C,X 153 I T T,C,X 153 II,III T T,C,X 10 I T T,C,X 10 II,III T T,C,X 15 I T T,C,X 15 II,III T T,C,X 109 I T T,C,X 109 I T T,C,X 109 II,III A 36T T,C,X 97 I T T,C,X 97 II,III A 36T T,C,X 86 I T T,C,X 78 I,II,III T T,C,X 69 I T T,C,X 69 II,III T T,C,X 61 I T T,C,X 61 II T T,C,X 61 III T T,C,X 55 I,II T T,C,X 55 III T T,C,X Standard Motor Types (see page B-10 for product codes) T TEFC, three phase, 08-30/60 or 575 volts C Corro-Duty, three phase, 30/60 or 575 volts X Explosionproof, Cls I Grp D, Cls II Grps F&G, three phase, 30/60 or 575 volts Overhung loads are at shaft midpoint B-60

61 SELECTION TABLES 50 HP GEARMOTORS General Specifications: Totally enclosed, 60 hertz, 0 C ambient, continuous duty. 50 HORSEPOWER (continued) Output AGMA Service Output Torque OHL Nominal Frame Size Std. Motor RPM Class Factor in-lb lb Ratio Gear Motor Types 9 I,II T T,C,X 9 III T T,C,X 3 I T T,C,X 3 II,III T T,C,X 39 I T T,C,X 39 II,III T T,C,X 36 I,II T T,C,X 3 I,II T T,C,X 8 I T T,C,X 3 I T T,C,X 19. I T T,C,X Standard Motor Types (see page B-10 for product codes) T TEFC, three phase, 08-30/60 or 575 volts C Corro-Duty, three phase, 30/60 or 575 volts X Explosionproof, Cls I Grp D, Cls II Grps F&G, three phase, 30/60 or 575 volts Overhung loads are at shaft midpoint B-61

62 SELECTION TABLES 60 HP GEARMOTORS General Specifications: Totally enclosed, 60 hertz, 0 C ambient, continuous duty. 60 HORSEPOWER Output AGMA Service Output Torque OHL Nominal Frame Size Std. Motor RPM Class Factor in-lb lb Ratio Gear Motor Types 55 I, II T T,C,X 89 I, II T T,C,X 3 I T T,C,X 380 I T T,C,X 350 II, III T T,C,X 31 I,II,III T T,C,X 77 I, II, III T T,C,X 5 I, II T T,C,X 17 I, II T T,C,X 17 III T T,C,X 191 I, II T T,C,X 191 III T T,C,X 175 I, II T T,C,X 175 III T T,C,X 155 I, II, III T T,C,X 10 I, II T T,C,X 15 I, II T T,C,X 15 III A 36T T,C,X 110 I, II, III A 36T T,C,X 98 I, II, III A 36T T,C,X 79 I, II T T,C,X 79 III T T,C,X 70 I, II T T,C,X 70 III T T,C,X 61 I, II T T,C,X 61 III T T,C,X 55 I,II T T,C,X 55 III T T,C,X 9 I T T,C,X 9 II,III T T,C,X 3 I T T,C,X 3 II T T,C,X 36 I, II T T,C,X 3 I T T,C,X 8 I T T,C,X I T T,C,X Refer to office if vertical mounting with shaft high or low is required for frames 60 or 70. Standard Motor Types (see page B-10 for product codes) T TEFC, three phase, 08-30/60 or 575 volts C Corro-Duty, three phase, 30/60 or 575 volts X Explosionproof, Cls I Grp D, Cls II Grps F&G, three phase, 30/60 or 575 volts Overhung loads are at shaft midpoint B-6

63 SELECTION TABLES 75 HP GEARMOTORS General Specifications: Totally enclosed, 60 hertz, 0 C ambient, continuous duty. 75 HORSEPOWER Output AGMA Service Output Torque OHL Nominal Frame Size Std. Motor RPM Class Factor in-lb lb Ratio Gear Motor Types 350 I, II T T,C,X 31 I, II, III T T,C,X, 77 I, II T T,C,X 1 I, II T T,C,X 16 I, II T T,C,X 196 I, II T T,C,X 170 I, II T T,C,X 170 III A 365T T,C,X 155 I, II T T,C,X 155 III A 365T T,C,X 10 I, II T T,C,X 10 II A 365T T,C,X 15 I T T,C,X 15 II A 365T T,C,X 109 I, II A 365T T,C,X 98 I, II A 365T T,C,X 78 I,II T T,C,X 78 II T T,C,X 70 I,II T T,C,X 70 II T T,C,X 63 I T T,C,X 63 II T T,C,X 56 I T T,C,X 56 II T T,C,X 9 I T T,C,X 9 II T T,C,X I, II T T,C,X 39 I T T,C,X 35 I T T,C,X 3 I T T,C,X Refer to office if vertical mounting with shaft high or low is required for frames 60 or 70. Standard Motor Types (see page B-10 for product codes) T TEFC, three phase, 08-30/60 or 575 volts C Corro-Duty, three phase, 30/60 or 575 volts X Explosionproof, Cls I Grp D, Cls II Grps F&G, three phase, 30/60 or 575 volts Overhung loads are at shaft midpoint B-63

64 DIMENSIONAL DATA GEARMOTORS FOOT MOUNT THREE PHASE SINGLE REDUCTION GEAR A B D 1 D E E F G H J U 3 V Y BA UY MOTOR TYPE C O P 5 AA AB AC AF BS WEIGHT LB. 18T-01 T T-01 T T-01 T T-01 T / T-01 T / T-01 X T, 15T-01 X T, 56T-01 X / T-01 C T, 15T-01 C T, 56T-01 C / Dimension "D" will never be exceeded, but may vary from values shown. When exact dimensions are required. Shims up to.03" may be necessary. All rough casting dimensions may vary by.5" due to casting variations. 3 Shaft extension tolerance: ";.0005" up to 1.5" diameter inclusive. Larger diameters: +.000";.001". Conduit box may be located on either side or on top of motor. Conduit openings may be located in steps of 90 regardless of location. Standard as shown with conduit opening down. 5 Largest motor width. B-6

65 DIMENSIONAL DATA GEARMOTORS FOOT MOUNT THREE PHASE SINGLE REDUCTION GEAR A B D 1 D E E F G H J U 3 V Y BA UY MOTOR TYPE C O P 5 AA AB AC AF BS WEIGHT LB. 13T-501 T T-501 T T-501 T / T-501 T / A8T-501 T / A86T-501 T / , 15T-501 X T, 56T-501 X / T, 86T-501 X T, 15T-501 C T, 56T-501 C / T, 86T-501 C / Dimension "D" will never be exceeded, but may vary from values shown. When exact dimensions are required. Shims up to.03" may be necessary. All rough casting dimensions may vary by.5" due to casting variations. 3 Shaft extension tolerance: ";.0005" up to 1.5" diameter inclusive. Larger diameters: +.000";.001". Conduit box may be located on either side or on top of motor. Conduit openings may be located in steps of 90 regardless of location. Standard as shown with conduit opening down. 5 Largest motor width. B-65

66 DIMENSIONAL DATA GEARMOTORS FOOT MOUNT SINGLE PHASE C BS V AB AC AB AC XT P U O BU XD AA - SIZE CONDUIT H - HOLES F B BA AF C J E E D VIEW A AF VIEW B UY Y A MOTOR 6, 13T, 15TY DOUBLE AND TRIPLE REDUCTION TYPE P 5 AA 5 S AB AC AF GEAR A B D 1 E E F G H J U 3 V Y BA UY / MOTOR TYPE HP VIEW C O BS BU XD XT WEIGHT LB. 56- S A NA T- S 1 A NA TY- S 1 1/, B T-5 S 1 A NA TY-5 S 1 1/, B Dimension "D" will never be exceeded, but may vary from values shown. When exact dimensions are required. Shims up to.03" may be necessary. All rough casting dimensions may vary by.5" due to casting variations. 3 Shaft extension tolerance: ";.0005" up to 1.5" diameter inclusive. Larger diameters: +.000";.001". Conduit box may be located on either side or on top of motor. Conduit openings may be located in steps of 90 regardless of location. Standard as shown with conduit opening down. 5 Largest motor width. B-66

67 DIMENSIONAL DATA GEARMOTORS FOOT MOUNT THREE PHASE DOUBLE AND TRIPLE REDUCTION GEAR A B D 1 E E F G H J U 3 V Y BA UY MOTOR TYPE C O P 5 AA AB AC AF BS XD W EIGHT LB. 56- T T, 15T- T TY- T T, 18T- T T- T T- T T- T / T- T / X T, 15T- X T, 18T- X T, 15T- X T, 56T- X / C T, 15T- C TY- C T, 18T- C T, 15T- C T, 56T- C / Dimension "D" will never be exceeded, but may vary from values shown. When exact dimensions are required. Shims up to.03" may be necessary. All rough casting dimensions may vary by.5" due to casting variations. 3 Shaft extension tolerance: ";.0005" up to 1.5" diameter inclusive. Larger diameters: +.000";.001". Conduit box may be located on either side or on top of motor. Conduit openings may be located in steps of 90 regardless of location. Standard as shown with conduit opening down. 5 Largest motor width. B-67

68 DIMENSIONAL DATA GEARMOTORS FOOT MOUNT THREE PHASE DOUBLE AND TRIPLE REDUCTION GEAR A B D 1 E E F G H J U 3 V Y BA UY / MOTOR TYPE C O P 5 AA AB AC AF BS XD W EIGHT LB. 13T, 15T-5 T TY-5 T T, 18T-5 T T-5 T T-5 T T-5 T / T-5 T A8T-5 T / A86T-5 T / T, 15T-5 X T, 18T-5 X T, 15T-5 X T, 56T-5 X / T, 86T-5 X T, 15T-5 C TY-5 C T, 18T-5 C T, 15T-5 C T, 56T-5 C / T, 86T-5 C / Dimension "D" will never be exceeded, but may vary from values shown. When exact dimensions are required. Shims up to.03" may be necessary. All rough casting dimensions may vary by.5" due to casting variations. 3 Shaft extension tolerance: ";.0005" up to 1.5" diameter inclusive. Larger diameters: +.000";.001". Conduit box may be located on either side or on top of motor. Conduit openings may be located in steps of 90 regardless of location. Standard as shown with conduit opening down. 5 Largest motor width. B-68

69 DIMENSIONAL DATA GEARMOTORS FOOT MOUNT THREE PHASE DOUBLE AND TRIPLE REDUCTION GEAR A B D 1 E E F G H J U 3 V Y BA UY MOTOR TYPE C O P 5 AA AB AC AF BS XD W EIGHT LB. 18T, 18T-6 T T-603 T T-60 T T-603 T T-6 T / T-6 T / A8T-6 T / A86T-6 T / T, 18T-6 X T, 15T-60 X T, 15T-603 X T, 56T-6 X / T, 86T-6 X / T, 18T-6 C T, 15T-60 C T, 15T-603 C T, 56T-6 C / T, 86T-6 C / T, 36T-6 T T, 365T-6 T Dimension "D" will never be exceeded, but may vary from values shown. When exact dimensions are required. Shims up to.03" may be necessary. All rough casting dimensions may vary by.5" due to casting variations. 3 Shaft extension tolerance: ";.0005" up to 1.5" diameter inclusive. Larger diameters: +.000";.001". Conduit box may be located on either side or on top of motor. Conduit openings may be located in steps of 90 regardless of location. Standard as shown with conduit opening down. 5 Largest motor width. B-69

70 DIMENSIONAL DATA GEARMOTORS FOOT MOUNT THREE PHASE DOUBLE AND TRIPLE REDUCTION GEAR A B D 1 E E F G H J U 3 V Y BA UY / MOTOR TYPE C O P 5 AA AB AC AF BS XD W EIGHT LB. 18T, 18T-7 T T-703 T T-70 T T-703 T T-7 T / T-7 T / A8T-7 T / A86T-7 T / T, 18T-7 X T, 15T-70 X T, 15T-703 X T, 56T-7 X / T, 86T-7 X / T, 18T-7 C T, 15T-70 C T, 15T-703 C T, 56T-7 C / T, 86T-7 C / T, 36T-7 T T, 365-T-7 T Dimension "D" will never be exceeded, but may vary from values shown. When exact dimensions are required. Shims up to.03" may be necessary. All rough casting dimensions may vary by.5" due to casting variations. 3 Shaft extension tolerance: ";.0005" up to 1.5" diameter inclusive. Larger diameters: +.000";.001". Conduit box may be located on either side or on top of motor. Conduit openings may be located in steps of 90 regardless of location. Standard as shown with conduit opening down. 5 Largest motor width. B-70

71 DIMENSIONAL DATA GEARMOTORS FOOT MOUNT THREE PHASE DOUBLE AND TRIPLE REDUCTION GEAR A B D 1 E E F G H J U 3 V Y BA UY MOTOR TYPE C O P 5 AA AB AC AF BS XD WEIGHT LB. 13T-8 T T-8 T T-8 T / T-8 T / A8T-8 T / A86T-8 T / T, 15T-8 X T, 56T-8 X / T, 86T-8 X / T, 36T-8 X T, 15T-8 C T, 56T-8 C / T, 86T-8 C / T, 36T-8 T T, 365T-8 T Dimension "D" will never be exceeded, but may vary from values shown. When exact dimensions are required. Shims up to.03" may be necessary. All rough casting dimensions may vary by.5" due to casting variations. 3 Shaft extension tolerance: ";.0005" up to 1.5" diameter inclusive. Larger diameters: +.000";.001". Conduit box may be located on either side or on top of motor. Conduit openings may be located in steps of 90 regardless of location. Standard as shown with conduit opening down. 5 Largest motor width. 6 These dimensions apply to 803A. B-71

72 DIMENSIONAL DATA GEARMOTORS FOOT MOUNT THREE PHASE DOUBLE AND TRIPLE REDUCTION GEAR A B D 1 E E F G H J U 3 V Y BA UY / MOTOR TYPE C O P 5 AA AB AC AF BS XD WEIGHT LB. 5T-9 T / T-9 T / A8T-9 T / A86T-9 T / T, 36T-9 T T, 365T-9 T T, 56T-9 X / T, 86T-9 X / T, 36T-9 X T, 56T-9 C / T, 86T-9 C / T, 36T-9 C Dimension "D" will never be exceeded, but may vary from values shown. When exact dimensions are required. Shims up to.03" may be necessary. All rough casting dimensions may vary by.5" due to casting variations. 3 Shaft extension tolerance: ";.0005" up to 1.5" diameter inclusive. Larger diameters: +.000";.001". Conduit box may be located on either side or on top of motor. Conduit openings may be located in steps of 90 regardless of location. Standard as shown with conduit opening down. 5 Largest motor width. B-7

73 DIMENSIONAL DATA GEARMOTORS BS FLANGED MOUNT THREE PHASE SINGLE REDUCTION GEAR U 3 Y AH AJ AK BB BD BE BF XN UY MOTOR TYPE C O P 5 AA AB AC AF BV WEIGHT LB. 18T-01 T T-01 T T-01 T T-01 T / T-01 T / T-01 X T, 15T-01 X T, 56T-01 X / T-01 C T, 15T-01 C T, 56T-01 C / All rough casting dimensions may vary by.5" due to casting variations. 3 Shaft extension tolerance: ";.0005" up to 1.5" diameter inclusive. Larger diameters: +.000";.001". Conduit box may be located on either side or on top of motor. Conduit openings may be located in steps of 90 regardless of location. Standard as shown with conduit opening down. 5 Largest motor width. B-73

74 DIMENSIONAL DATA GEARMOTORS BS FLANGED MOUNT THREE PHASE SINGLE REDUCTION GEAR U 3 Y AH AJ AK BB BD BE BF XN UY MOTOR TYPE C O P 5 AA AB AC AF BV WEIGHT LB. 13T-501 T T-501 T T-501 T / T-501 T / A8T-501 T / A86T-501 T / T, 15T-501 X T, 56T-501 X / T, 86T-501 X T, 15T-501 C T, 56T-501 C / T, 86T-501 C / B-7 All rough casting dimensions may vary by.5" due to casting variations. 3 Shaft extension tolerance: ";.0005" up to 1.5" diameter inclusive. Larger diameters: +.000";.001". Conduit box may be located on either side or on top of motor. Conduit openings may be located in steps of 90 regardless of location. Standard as shown with conduit opening down. 5 Largest motor width.

75 DIMENSIONAL DATA GEARMOTORS BS FLANGED MOUNT SINGLE PHASE MOTOR 6, 13T, 15TY DOUBLE AND TRIPLE REDUCTION TYPE P AA 5 S AB AC AF GEAR U Y AH AJ AK BB BD BE BF UY / TYPE HP VIEW C O BU BV XT WEIGHT LB. 56- S A NA T- S 1 A NA TY- S 1 1/, B T-5 S 1 A NA TY-5 S 1 1/, B All rough casting dimensions may vary by.5" due to casting variations. 3 Shaft extension tolerance: ";.0005" up to 1.5" diameter inclusive. Larger diameters: +.000";.001". Conduit box may be located on either side or on top of motor. Conduit openings may be located in steps of 90 regardless of location. Standard as shown with conduit opening down. 5 Largest motor width. B-75

76 DIMENSIONAL DATA GEARMOTORS BS FLANGED MOUNT THREE PHASE DOUBLE AND TRIPLE REDUCTION GEAR U 3 Y AH AJ AK BB BD BE BF UY MOTOR TYPE C O P 5 AA AB AC AF BV WEIGHT LB. 56- T T, 15T- T TY- T T, 18T- T T- T T- T T- T / T- T / X T, 15T- X T, 18T- X T, 15T- X T, 56T- X / C T, 15T- C TY- C T, 18T- C T, 15T- C T, 15T- C / B-76 All rough casting dimensions may vary by.5" due to casting variations. 3 Shaft extension tolerance: ";.0005" up to 1.5" diameter inclusive. Larger diameters: +.000";.001". Conduit box may be located on either side or on top of motor. Conduit openings may be located in steps of 90 regardless of location. Standard as shown with conduit opening down. 5 Largest motor width.

77 DIMENSIONAL DATA GEARMOTORS BS FLANGED MOUNT THREE PHASE DOUBLE AND TRIPLE REDUCTION GEAR U 3 Y AH AJ AK BB BD BE BF UY / MOTOR TYPE C O P 5 AA AB AC AF BV W EIGHT LB. 13T, 15T-5 T TY-5 T T, 18T-5 T T-5 T T-5 T T-5 T / T-5 T / A8T-5 T / A86T-5 T / T, 15T-5 X T, 18T-5 X T, 15T-5 X T, 56T-5 X / T, 86T-5 X T, 15T-5 C TY-5 C T, 18T-5 C T, 15T-5 C T, 56T-5 C / T, 86T-5 C / All rough casting dimensions may vary by.5" due to casting variations. 3 Shaft extension tolerance: ";.0005" up to 1.5" diameter inclusive. Larger diameters: +.000";.001". Conduit box may be located on either side or on top of motor. Conduit openings may be located in steps of 90 regardless of location. Standard as shown with conduit opening down. 5 Largest motor width. B-77

78 DIMENSIONAL DATA GEARMOTORS BS FLANGED MOUNT THREE PHASE DOUBLE AND TRIPLE REDUCTION GEAR U 3 Y AH AJ AK BB BD BE BF UY MOTOR TYPE C O P 5 AA AB AC AF BV W EIGHT LB. 18T, 18T-6 T T-60 T T-603 T T-60 T T-603 T T-6 T / T-6 T / A8T-6 T / A86T-6 T / T, 18T-6 X T, 15T-60 X T, 15T-603 X T-56T-6 X / T, 86T-6 X / T, 18T-6 C T, 15T-60 C T, 15T-603 C T, 56T-6 C / T, 86T-6 C / T, 36T-6 T B-78 All rough casting dimensions may vary by.5" due to casting variations. 3 Shaft extension tolerance: ";.0005" up to 1.5" diameter inclusive. Larger diameters: +.000";.001". Conduit box may be located on either side or on top of motor. Conduit openings may be located in steps of 90 regardless of location. Standard as shown with conduit opening down. 5 Largest motor width.

79 DIMENSIONAL DATA GEARMOTORS BS FLANGED MOUNT THREE PHASE DOUBLE AND TRIPLE REDUCTION GEAR U 3 Y AH AJ AK BB BD BE BF UY / MOTOR TYPE C O P 5 AA AB AC AF BV W EIGHT LB. 18T, 18T-7 T T-70 T T-703 T T-70 T T-703 T T-7 T / T-7 T / A8T-7 T / A86T-7 T / T, 18T-7 X T, 15T-70 X T, 15T-703 X T, 56T-7 X / T, 86T-7 X / T, 18T-7 C T, 15T-70 C T, 15T-703 C T, 56T-7 C / T, 86T-7 C / T, 36T-7 T All rough casting dimensions may vary by.5" due to casting variations. 3 Shaft extension tolerance: ";.0005" up to 1.5" diameter inclusive. Larger diameters: +.000";.001". Conduit box may be located on either side or on top of motor. Conduit openings may be located in steps of 90 regardless of location. Standard as shown with conduit opening down. 5 Largest motor width. B-79

80 DIMENSIONAL DATA GEARMOTORS BS FLANGED MOUNT THREE PHASE DOUBLE AND TRIPLE REDUCTION GEAR U 3 Y AH AJ AK BB BD BE BF UY MOTOR TYPE C O P 5 AA AB AC AF BV WEIGHT LB. 13T-8 T T-8 T T-8 T / T-8 T / A8T-8 T / A86T-8 T / T, 36T-8 T T, 15T-8 X T, 56T-8 X / T, 86T-8 X / T, 36T-8 X T, 15T-8 C T, 56T-8 C / T, 86T-8 C / T, 36T-8 T T, 365T-8 T All rough casting dimensions may vary by.5" due to casting variations. 3 Shaft extension tolerance: ";.0005" up to 1.5" diameter inclusive. Larger diameters: +.000";.001". Conduit box may be located on either side or on top of motor. Conduit openings may be located in steps of 90 regardless of location. Standard as shown with conduit opening down. 5 Largest motor width. 6 These dimensions apply to 803A. B-80

81 DIMENSIONAL DATA GEARMOTORS FOOT MOUNT COMBINED SINGLE PHASE FOUR, FIVE, AND SIX STAGE REDUCTION MOTOR TYPE P 5 AA AB AC AF 56, 13T, 15TY S GEAR A B D 1 E E F G H J U 3 V Y BA UY HP VIEW C O BS BU XD XT WEIGHT LB. 56-1/ 3 A NA / A NA A NA T- 1 A NA TY- 1 1/ B Dimension "D" will never be exceeded, but may vary from values shown. When exact dimensions are required. Shims up to.03" may be necessary. All rough casting dimensions may vary by.5" due to casting variations. 3 Shaft extension tolerance: ";.0005" up to 1.5" diameter inclusive. Larger diameters: +.000";.001". Conduit box may be located on either side or on top of motor. Conduit openings may be located in steps of 90 regardless of location. Standard as shown with conduit opening down. 5 Largest motor width. B-81

82 DIMENSIONAL DATA GEARMOTORS FOOT MOUNT COMBINED SINGLE PHASE FOUR, FIVE, AND SIX STAGE REDUCTION MOTOR TYPE P 5 AA AB AC AF 56, 13T, 15TY S GEAR A B D 1 E E F G H J U 3 V Y BA UY / HP VIEW C O BS BU XD XT WEIGHT LB / 3 A NA / A NA A NA T-5 1 A NA TY-5 1 1/, B / 3 A NA / A NA A NA T-6 1 A NA TY-6 1 1/, B B-8 1 Dimension "D" will never be exceeded, but may vary from values shown. When exact dimensions are required. Shims up to.03" may be necessary. All rough casting dimensions may vary by.5" due to casting variations. 3 Shaft extension tolerance: ";.0005" up to 1.5" diameter inclusive. Larger diameters: +.000";.001". Conduit box may be located on either side or on top of motor. Conduit openings may be located in steps of 90 regardless of location. Standard as shown with conduit opening down. 5 Largest motor width.

83 DIMENSIONAL DATA GEARMOTORS FOOT MOUNT COMBINED SINGLE PHASE FOUR, FIVE, AND SIX STAGE REDUCTION MOTOR TYPE P 5 AA AB AC AF 56, 13T, 15TY S GEAR A B D 1 E E F G H J U 3 V Y BA UY / / VIEW HP C O BS BU XD XT W EIGHT LB / 3 A NA / A NA A NA T-7 1 A NA TY-7 1 1/, B / 3 A NA / A NA A NA T-8 1 A NA TY-8 1 1/, B / 3 A NA / A NA A NA T-9 1 A NA TY-9 1 1/, B Dimension "D" will never be exceeded, but may vary from values shown. When exact dimensions are required. Shims up to.03" may be necessary. All rough casting dimensions may vary by.5" due to casting variations. 3 Shaft extension tolerance: ";.0005" up to 1.5" diameter inclusive. Larger diameters: +.000";.001". Conduit box may be located on either side or on top of motor. Conduit openings may be located in steps of 90 regardless of location. Standard as shown with conduit opening down. 5 Largest motor width. B-83

84 DIMENSIONAL DATA GEARMOTORS FOOT MOUNT COMBINED THREE PHASE FOUR, FIVE, AND SIX STAGE REDUCTION GEAR A B D 1 E E F G H J U 3 V Y BA UY MOTOR TYPE C O P 5 AA AB AC AF BS XD W EIGHT LB. 56- T T, 15T- T X T, 15T- X C T, 15T- C B-8 1 Dimension "D" will never be exceeded, but may vary from values shown. When exact dimensions are required. Shims up to.03" may be necessary. All rough casting dimensions may vary by.5" due to casting variations. 3 Shaft extension tolerance: ";.0005" up to 1.5" diameter inclusive. Larger diameters: +.000";.001". Conduit box may be located on either side or on top of motor. Conduit openings may be located in steps of 90 regardless of location. Standard as shown with conduit opening down. 5 Largest motor width.

85 DIMENSIONAL DATA GEARMOTORS FOOT MOUNT COMBINED THREE PHASE FOUR, FIVE, AND SIX STAGE REDUCTION GEAR A B D 1 E E F G H J U 3 V Y BA UY / MOTOR TYPE C O P 5 AA AB AC AF BS XD WEIGHT LB T T, 15T-5 T TY-5 T T-5 T T T, 15T-6 T X T, 15T-5 X T-5 X X T, 15T-6 X C T, 15T-5 C TY-5 C T-5 C C T, 15T-6 C Dimension "D" will never be exceeded, but may vary from values shown. When exact dimensions are required. Shims up to.03" may be necessary. All rough casting dimensions may vary by.5" due to casting variations. 3 Shaft extension tolerance: ";.0005" up to 1.5" diameter inclusive. Larger diameters: +.000";.001". Conduit box may be located on either side or on top of motor. Conduit openings may be located in steps of 90 regardless of location. Standard as shown with conduit opening down. 5 Largest motor width. B-85

86 DIMENSIONAL DATA GEARMOTORS FOOT MOUNT COMBINED THREE PHASE FOUR, FIVE, AND SIX STAGE REDUCTION GEAR A B D 1 E E F G H J U 3 V Y BA UY / MOTOR TYPE C O P 5 AA AB AC AF BS XD W EIGHT LB T T, 15T-7 T TY-7 T T, 18T-7 T T-7 T X T, 15T-7 X T, 18T-7 X T-7 X C T, 15T-7 C TY-7 C T, 18T-7 C T-7 C B-86 1 Dimension "D" will never be exceeded, but may vary from values shown. When exact dimensions are required. Shims up to.03" may be necessary. All rough casting dimensions may vary by.5" due to casting variations. 3 Shaft extension tolerance: ";.0005" up to 1.5" diameter inclusive. Larger diameters: +.000";.001". Conduit box may be located on either side or on top of motor. Conduit openings may be located in steps of 90 regardless of location. Standard as shown with conduit opening down. 5 Largest motor width.

87 DIMENSIONAL DATA GEARMOTORS FOOT MOUNT COMBINED THREE PHASE FOUR, FIVE, AND SIX STAGE REDUCTION GEAR A B D 1 E E F G H J U 3 V Y BA UY MOTOR TYPE C O P 5 AA AB AC AF BS XD WEIGHT LB T T, 15T-8 T TY-8 T T, 18T-8 T T-8 T T-8 T X T, 15T-8 X T, 18T-8 X T, 15T-8 X C T, 15T-8 C TY-8 C T, 18T-8 C T, 15T-8 C Dimension "D" will never be exceeded, but may vary from values shown. When exact dimensions are required. Shims up to.03" may be necessary. All rough casting dimensions may vary by.5" due to casting variations. 3 Shaft extension tolerance: ";.0005" up to 1.5" diameter inclusive. Larger diameters: +.000";.001". Conduit box may be located on either side or on top of motor. Conduit openings may be located in steps of 90 regardless of location. Standard as shown with conduit opening down. 5 Largest motor width. B-87

88 DIMENSIONAL DATA GEARMOTORS FOOT MOUNT COMBINED THREE PHASE FIVE AND SIX STAGE REDUCTION GEAR A B D 1 E E F G H J U 3 V Y BA UY / MOTOR TYPE C O P 5 AA AB AC AF BS XD WEIGHT LB T T, 15T-9 T TY-9 T T, 18T-9 T T-9 T T-9 T T-9 T / T-9 T / X T, 15T-9 X T, 18T-9 X T, 15T-9 X T, 56T-9 X / C T, 15T-9 C TY-9 C T, 18T-9 C T, 15T-9 C T, 56T-9 C / B-88 1 Dimension "D" will never be exceeded, but may vary from values shown. When exact dimensions are required. Shims up to.03" may be necessary. All rough casting dimensions may vary by.5" due to casting variations. 3 Shaft extension tolerance: ";.0005" up to 1.5" diameter inclusive. Larger diameters: +.000";.001". Conduit box may be located on either side or on top of motor. Conduit openings may be located in steps of 90 regardless of location. Standard as shown with conduit opening down. 5 Largest motor width.

89 DIMENSIONAL DATA GEARMOTORS OUTPUT SHAFT FLANGED MOUNT COMBINED SINGLE PHASE MOTOR 6, 13T, 15TY FIVE AND SIX STAGE REDUCTION TYPE P 5 AA 5 S GEAR U 3 Y AH AJ AK BB BD BE BF UY / HP VIEW C O BS BU XT WEIGHT LB. 56-1/ 3 A NA / A NA A NA T- 1 A NA TY- 1 1/ B / 3 A NA / A NA A NA T-5 1 A NA TY-5 1 1/, B AB AC AF 1 Dimension "D" will never be exceeded, but may vary from values shown. When exact dimensions are required. Shims up to.03" may be necessary. All rough casting dimensions may vary by.5" due to casting variations. 3 Shaft extension tolerance: ";.0005" up to 1.5" diameter inclusive. Larger diameters: +.000";.001". Conduit box may be located on either side or on top of motor. Conduit openings may be located in steps of 90 regardless of location. Standard as shown with conduit opening down. 5 Largest motor width. B-89

90 DIMENSIONAL DATA GEARMOTORS BS FLANGED MOUNT COMBINED SINGLE PHASE FOUR, FIVE, AND SIX STAGE REDUCTION MOTOR TYPE P 5 AA AB AC AF 56, 13T, 15TY S GEAR U 3 Y AH AJ AK BB BD BE BF UY / HP VIEW C O BS BU XT WEIGHT LB / 3 A NA / A NA A NA T-6 1 A NA TY-6 1 1/, B / 3 A NA / A NA A NA T-7 1 A NA TY-7 1 1/, B / 3 A NA / A NA A NA T-8 1 A NA TY-8 1 1/, B B-90 All rough casting dimensions may vary by.5" due to casting variations. 3 Shaft extension tolerance: ";.0005" up to 1.5" diameter inclusive. Larger diameters: +.000";.001". Conduit box may be located on either side or on top of motor. Conduit openings may be located in steps of 90 regardless of location. Standard as shown with conduit opening down. 5 Largest motor width.

91 DIMENSIONAL DATA GEARMOTORS BS FLANGED MOUNT COMBINED THREE PHASE FOUR, FIVE, AND SIX STAGE REDUCTION GEAR U 3 Y AH AJ AK BB BD BE BF UY MOTOR TYPE C O P 5 AA AB AC AF BV W EIGHT LB. 56- T T, 15T- T X T, 15T- X C T, 15T- C All rough casting dimensions may vary by.5" due to casting variations. 3 Shaft extension tolerance: ";.0005" up to 1.5" diameter inclusive. Larger diameters: +.000";.001". Conduit box may be located on either side or on top of motor. Conduit openings may be located in steps of 90 regardless of location. Standard as shown with conduit opening down. 5 Largest motor width. B-91

92 DIMENSIONAL DATA GEARMOTORS BS FLANGED MOUNT COMBINED THREE PHASE FOUR, FIVE AND SIX STAGE REDUCTION GEAR U 3 Y AH AJ AK BB BD BE BF UY N / MOTOR TYPE C O P 5 AA AB AC AF BV WEIGHT LB T T, 15T-5 T TY-5 T T-5 T T T, 15T-6 T X T, 15T-5 X T-5 X X T, 15T-6 X C T, 15T-5 C TY-5 C T-5 C C T, 15T-6 C B-9 All rough casting dimensions may vary by.5" due to casting variations. 3 Shaft extension tolerance: ";.0005" up to 1.5" diameter inclusive. Larger diameters: +.000";.001". Conduit box may be located on either side or on top of motor. Conduit openings may be located in steps of 90 regardless of location. Standard as shown with conduit opening down. 5 Largest motor width.

93 DIMENSIONAL DATA GEARMOTORS BS FLANGED MOUNT COMBINED THREE PHASE FOUR, FIVE, AND SIX STAGE REDUCTION GEAR U 3 Y AH AJ AK BB BD BE BF UY / MOTOR TYPE C O P 5 AA AB AC AF BV W EIGHT LB T T, 15T-7 T TY-7 T T, 18T-7 T T-7 T X T, 15T-7 X T, 18T-7 X T-7 X C T, 15T-7 C TY-7 C T, 18T-7 C T-7 C All rough casting dimensions may vary by.5" due to casting variations. 3 Shaft extension tolerance: ";.0005" up to 1.5" diameter inclusive. Larger diameters: +.000";.001". Conduit box may be located on either side or on top of motor. Conduit openings may be located in steps of 90 regardless of location. Standard as shown with conduit opening down. 5 Largest motor width. B-93

94 DIMENSIONAL DATA GEARMOTORS BS FLANGED MOUNT COMBINED THREE PHASE FOUR, FIVE, AND SIX STAGE REDUCTION GEAR U 3 Y AH AJ AK BB BD BE BF UY MOTOR TYPE C O P 5 AA AB AC AF BV WEIGHT LB T T, 15T-8 T TY-8 T T, 18T-8 T T-8 T T-8 T X T, 15T-8 X T, 18T-8 X T, 15T-8 X C T, 15T-8 C TY-8 C T, 18T-8 C T, 15T-8 C B-9 All rough casting dimensions may vary by.5" due to casting variations. 3 Shaft extension tolerance: ";.0005" up to 1.5" diameter inclusive. Larger diameters: +.000";.001". Conduit box may be located on either side or on top of motor. Conduit openings may be located in steps of 90 regardless of location. Standard as shown with conduit opening down. 5 Largest motor width.

95 DIMENSIONAL DATA GEARMOTORS FOOTED WITH METRIC SM OUTPUT SHAFT SINGLE REDUCTION DIMENSIONS in mm Gear Frame D E F Z EX EY GA M: O 01 0 k k , 5 16 MULTIPLE REDUCTION DIMENSIONS in mm Gear Frame D E F Z EX EY GA M: O k , m m , m m m B-95

96 DIMENSIONAL DATA GEARMOTORS BSM FLANGED METRIC OUTPUT SHAFT SINGLE REDUCTION IN mm Gearbox Type Flange HB X M N P n* S LA T D E EY Output Shaft EX GA F M: O Z Cb k Cb k , *n = : a = 5" - n = 30'. B-96

97 VARIABLE SPEED GEARMOTORS DIMENSIONAL DATA BSM FLANGED METRIC OUTPUT SHAFT Gearbox Type *n = Number of holes in flange equally spaced. MULTIPLE REDUCTION IN mm Flange H Y M N P n* S LA T D E EY Output Shaft EX GA F M: O Cb k , Cb m Cb m , Cb m Cb m Z B-97

98 VARIABLE SPEED GEARMOTORS AD 1 AD X X 1 AB AC AE AE1 Weights and Dimensions Dimension (inches) Drive INTELLIGEAR Added Motor Frame Drive Size W eight AB AC AD AD1 AE AE1 X X1 (lb.) 56 1 or 1M T, 15T 1 or 1M TY T, 15T or M TY or M , 18T * Reduce AE and AE1 by.3 if motor HP is.75. AE1 includes braking resistor installed. INTELLIGEAR Selection Input Power Motor Max. Hz Phase/Voltage. 33 to to 3 to 5 1/30 1M M B-98

99 Take a peek at the future of variable speed gearmotors thru 5 HP and 15,000 in.-lbs. IF YOU... Specify,, buy or sell mechanical belt or traction type variable speed drives? Want to lower your initial installed cost? Want to lower your maintenance costs? Want 10% higher overall energy efficiency? Want superior drive enclosure, e, in a smaller,, lighter envelope? THEN... NOW AVAILABLE... Fax ax your complete application details to Gearing Marketing at and consider INTELLIGEAR. B-99

100 FEATURES and BENEFITS SPEED REDUCERS SERIES 000 TYPE HELICAL INLINE SERIES 000 SPEED REDUCER FEATURES Design Features 1. Gears and shafts are made of 10 heat treated nickel chromium molybdenum steel. Helical gearing is skived, superfinished, or ground after case hardening.. Gearbox is delivered filled with synthetic oil, ready to use. 3. Oversized ball, cylindrical, tapered or spherical roller bearings are used for long gearbox life.. Double lip seals are installed on plunge ground shafts. 5. All gears are heat shrunk on shafts, or mounted on self-locking tapered shafts and keyed for high shock loading capability. 6. Oversized plugs allow for quick oil change. Magnetic drain plug is supplied standard. 7. Cast iron housings are one piece, reinforced and ribbed, for extra strength. 7 B-100

101 Table of Contents SPEED REDUCERS SERIES 000 Section Page Mounting Versatility and Size Range Reducer Selection Catalog Nomenclature and Flange Options Overhung Load Capacities Mounting Positions AGMA Application Tables Lubrication Reducer Selection Tables Exact Ratios and Moments of Inertia... 1 Thermal Power Ratings Modifications Dimension Prints (inch) Input Shaft Reducers - Footed Scoop Mount Reducers - Footed Input Shaft Reducers - Flanged C-Face Reducers - Footed C-Face Reducers - Flanged Dimension Print Supplements Metric Output Shafts B-101

102 SPEED REDUCERS SERIES 000 MOUNTING VERSATILITY & SIZE RANGE Foot Mount Frames 8 Max. 150,000 in. lbs. Input Shaft Assembly Frames - 9 BackStop Frames: -9 Scoop Mount Sizes: 3-9 Motor Frames: 13T-365T Flange Mount Frames 8 Max. 89,000 in. lbs. NEMA C-Face Adapter Frames - 9 NEMA Frames 56C-36TC CONFIGURATION OPTIONS High Ratio Foot Mount Frames 9 Max. 150,000 in. lbs. STANDARD OUTPUT SHAFT SCOOP MOUNT FACE-MOUNT HOLLOW SHAFT High Ratio Flange Mount Frames 8 Max. 89,000 in. lbs. C-FACE FLANGED OUTPUT B-10

103 SELECTION SPEED REDUCERS SERIES 000 SELECTION INFORMATION 1. Input HP Based on application data.. Speed/Ratio Obtain either desired output speed (RPM) or gearbox ratio based on application. 3. Service Factor Determine the required service factor using either the AGMA Application Classification chart (pages B-107-B-109), or the duration of operation, load type, and drive type with the table below. PRIME MOVER Electric Motor Internal Combustion Engine HOURS OF OPERATION SIZE SELECTION Step 1 Locate speed reducer selection tables (pages B-11- B-13) based on input speed to gearbox. Step Choose the nominal ratio appropriate for the speeds required. Step 3 Select the gear unit size for the chosen ratio and the known input speed so that the mechanical power rating P (hp) satisfies the following: P P m SF P = mechanical power rating (hp) of gearbox P m = motor power (hp) SF = required service factor Note: Size selection based on absorbed power (Pa) or absorbed torque (Ta) at the low speed shaft instead of motor power (Pm) is allowed when the former is known with sufficient accuracy and if the number of start operations is limited. When Ta is applied in size selection, verify if: T T a SF UNIFORM LOAD U MODERATE SHOCK LOAD M T = torque rating (in. lbs.) at low speed shaft T a = absorbed torque (in. lbs.) at low speed shaft (based on input hp) SF = required service factor HEAVY SHOCK LOAD V Size Selection (cont.) Step Verify thermal limitations where required (see pages B-15- B-16) P T P L P T P L = thermal power rating (hp) of gearbox = load power (hp) Step 5 Verify overhung load ratings where required (see page B-105) EXAMPLE 1. Application Data: Belt conveyor, uniform load, hr./ day operation. Speed reducer directly coupled to head pulley, reducer will be foot mounted on the floor. 350 RPM REQUIRED OUTPUT EQUALS 5:1 RATIO PM SF = P 0 HP 1.5 = 5 HP 0 (30. HP) 5 pg. B-11 SELECT 0 Customer prefers C-Face motors. Motor Rating: TEFC, 30/60 Volt, 0 HP, 1750 RPM, 56TC frame footless Output Speed: 350 RPM. Size Selection (There are no thermal or OHL considerations) 3. Catalog Designation (see "Ordering" page B-10) 5 0 EXAMPLE S B3 5 U 56TC. Motor Model Number (See page B-10 or refer to Motor Catalog for complete motor selection, dimensions and characteristics). TEFC, 30/60V 0 HP, 1750 RPM, 56TC frame footless No. U0SACR B-103

104 ORDERING SPEED REDUCERS SERIES S B3 5 U 56TC Type Based on Selection Gear Frame Number of Reductions 01 = 1 stage 0 = stages 03 = 3 stages 0 = stages 05 = 5 stages 06 = 6 stages Choose one Mounting Configuration S = BS = SM = BSM = Foot Mount Flange Mount Metric Foot Mount Metric Flange Mount Choose one Mounting Position see page B-106 Ratio Use Nominal Ratio Selected Based on Application Input AP = Input Shaft AD = Input Shaft (w/backstop)** SP* = Scoop Mount SD* = Scoop Mount U* = C-face (w/backstop)** Motor Frame Req'd on SP, SD, & U Mounting Modification Code(s) Number of Modification(s) From Page B-17 * Must specify NEMA frame size. ** For units with backstops, specify shaft rotation direction as viewed looking at the output shaft. -POLE, C-FACE MOTOR PART NUMBERS HP Frame Totally Enclosed Open Dripproof Washdown Duty 1 Ph., 115/30V 3 Ph., 08-30/60V 1 Ph., 115/30V 1 Ph., 115/08-30V 3 Ph., 08-30/60V 1/ 56C T1LICR 1/3 56C T13LICR U1SACR U13SACR D1LICR - - D13LJCR - - 1/ 56C T1LICR U1SACR D1LJCR WD1LJCR WD1SACR 56C T3LICR U3SACR D3LICR WD3LJCR WD3SACR 1 56C T1LJCR 13TC T1LJC1R 1 1/ 56C T3LJCR 15TC T3LJC1R 56C TLICR U1SAFCR D1LICR WD1LJCR WD1SAFCR U1SACR - - WD1SWACR U3SAFCR D3LJCR WD3LJCR WD3SAFCR U3SACR - - WD3SACR USAFCR - - WDSAFCR 15TC - USACR - - WDSACR 3 18TC - U3SACR - - WD3EDCR 5 18TC - U5SACR - - WD5EDCR 7 1/ 13TC - U7SACR TC - U10SACR TC - U15SACR TC - U0SACR A8TC - U5SACR A86TC - U30SACR See Catalog HM-98 for Complete EPT Motor Line, Dimensions and Performance Characteristics. B-10

105 OVERHUNG LOAD SPEED REDUCERS SERIES 000 When a sprocket, sheave, pulley, or pinion is mounted on the take-off shaft of a gearmotor, it is necessary to calculate the overhung load. This calculated load must be compared with the gearbox capacity listed to make sure the gearbox will not be overloaded. To calculate the overhung load you need to know the torque or horsepower at the take-off shaft and the location along the shaft at which the load is applied. A. If torque is known: OHL = B. If horsepower is known: OHL = T x K x LLF r 6305 x HP x K x LLF RPM x r Where: OHL = Overhung load (pounds) T = Torque (in. lbs.) r = Radius of driving member (in.) HP = Horsepower K = Drive type factor LLF = Load location factor DRIVING MEMBER VALUE OF K Chain Drive 1.00 Pinion 1.5 Timing Belt 1.5 V-Belt 1.50 Flat Belt.50 LOAD LOCATION VALUE OF LLF End of shaft extension 1.0 Center of shaft extension 1.00 Shaft extension shoulder 0.80 Output R.P.M. OVERHUNG LOAD (LBS.) REDUCER SIZE 5 > < MULTIPLE REDUCTION OVERHUNG LOAD (LBS.) Output R.P.M. REDUCER SIZE < B-105

106 MOUNTING POSITIONS SPEED REDUCERS SERIES 000 FOOT MOUNT S SINGLE REDUCTION MULTIPLE REDUCTION B3 B8 B3 B8 B6 B7 B6 B7 V5 V6 V5 V6 FOOT MOUNT BS SINGLE REDUCTION MULTIPLE REDUCTION B5 B5 B5 V1 B53 V1 V3 B5 V3 B-106

107 SPEED REDUCERS SERIES 000 AGMA APPLICATION CLASSIFICATION U: Uniform load M: Moderate shock load V: Heavy shock load Application Load Class Application Load Class Application Load Class Up to Up to Over hrs/day hrs/day hrs/day AGITATORS (Mixers) Pure Liquids Liquids & Solids Liquids - Variable Density BLOWERS Centrifugal Lobe Vane BREWING & DISTILLING Bottling Machinery Brew Kettles, Continuous Duty Cookers - Continuous Duty Mash Tubs - Continuous Duty Scale Hoppers, Frequent Starts Up to Up to Over hrs/day hrs/day hrs/day CRANES (Continued) Boom Hoist Refer to Tech. Service Trolley Drive Refer to Tech. Service (Gantry Drive) (Traction Drive) Refer to Tech. Service Mill Duty MainRefer To Engineering Auxiliary Refer to Tech. Service Bridge & Trolley Travel Refer to Tech. Service Industrial Duty Main Auxiliary Refer to Tech. Service Bridge & Trolley Travel Refer to Tech. Service CRUSHER Stone or Ore CAN FILLING MACHINES CAR DUMPERS CAR PULLERS CLARIFIERS CLASSIFIERS CLAY WORKING INDUSTRY Brick Press Briquette Machine Pug Mill COMPACTORS COMPRESSORS Centrifugal Lobe Reciprocating, Multi - Cylinder Reciprocating, Single - Cylinder CONVEYORS - GENERAL PURPOSE Uniformly Loaded or Fed Not Uniformly Fed Reciprocating or Shaker CRANES Dry Dock Main Hoist Auxiliary Boom Hoist Slewing Drive Traction Drive Container Main Hoist Refer to Tech. Service DREDGES Cable Reels Conveyors Cutter Head Drives Pumps Screen Drives Stackers Winches ELEVATORS Bucket Centrifugal Discharge Escalators Refer to Tech. Service Freight Refer to Tech. Service Gravity Discharge EXTRUDERS General Plastics (a) Variable Speed Drive (b) Fixed Speed Drive Rubber (a) Continuous Screw Operation (b) Intermittent Screw Operation FANS Centrifugal Cooling Towers Refer to Tech. Service Forced Draft Induced Draft Industrial & Mine B-107

108 AGMA APPLICATION CLASSIFICATION SPEED REDUCERS SERIES 000 U: Uniform load M: Moderate shock load V: Heavy shock load Application Load Class Application Load Class Application Load Class Up to Up to Over hrs/day hrs/day hrs/day Up to Up to Over hrs/day hrs/day hrs/day B-108 FEEDERS Apron Belt Disc Reciprocating Screw FOOD INDUSTRY Cereal Cooker Dough Mixers Meat Grinders Slicers GENERATORS & EXCUTERS HAMMER MILLS HOISTS Heavy Duty Medium Duty Skip Hoist LAUNDRY TUMBLERS LAUNDRY WASHERS LUMBER INDUSTRY Barkers - Spindle Feed Main Drive Conveyors - Burner Main or Heavy Duty Main Log Re-Saw, Merry-Go-Round Slab Transfer Chains - Floor Green Cut-Off Saws - Chain Drag Debarking Drums Feeds - Edger Gang Trimmer Log Deck Log Hauls - Incline-Well Type Log Turning Devices Planner Feed Planer Tilting Hoists Rolls - Live-Off Bearing.-Roll Cases Sorting Table Tipple Hoist Transfers - Chain Causeway Tray Drives Veneer Lathe Drives Refer to Tech. Service METAL MILLS Draw Bench Carriage & Main Drive Runout Table Non-reversing Group Drives Individual Drives Reversing Slab Pushers Shears Wire Drawing Wire Winding Machine METAL STRIP PROCESSING MACHINERY Bridles Coilers & Uncoilers Edge Trimmers Flatteners Loopers (Accumulators) Pinch Rolls Scrap Choppers Shears Slitters MILLS, ROTARY TYPE Ball & Rod Spur Ring Gear Helical Ring Gear Direct Connected Cement Kilns Dryers & Coolers MIXERS, CONCRETE PAPER MILLS Agitator (Mixer) Agitator for Pure Liquids Barkers - Mechanical Barking Drums Beater Breaker Stack Calender Chipper Chip Feeder Coating Rolls Conveyors Chip, Bark, Chemical Log (Including Slab) Couch Rolls Cutter Cylinder Molds Dryers Paper Machine Conveyor Type Embosser Extruder Fourdrinier Rolls (Includes Lump Breaker, Dandy Roll, Wire Turning, and Return Rolls) Jordan Kiln Drive Mt. Hope Roll

109 AGMA APPLICATION CLASSIFICATION SPEED REDUCERS SERIES 000 U: Uniform load M: Moderate shock load V: Heavy shock load Application Load Class Application Load Class Application Load Class Up to Up to Over hrs/day hrs/day hrs/day Up to Up to Over hrs/day hrs/day hrs/day PAPER MILLS (Continued) Paper Rolls Platter Presses - Felt & Suction Pulper Pumps - Vacuum Reel (Surface Type) Screens Chip Rotary Vibrating Size Press Super Calender (See Note) Thickner (AC Motor) (DC Motor) Washer (AC Motor) (DC Motor) Wind and Unwind Stand Winders (Surface Type) Yankee Dryers PLASTICS INDUSTRY - PRIMARY PROCESSING Intensive Internal Mixers (a) Batch Mixers (b) Continuous Mixers Batch Drop Mill - Smooth Rolls Continuous Feed, Holding & Blend Mill Compounding Mills Calenders PLASTICS INDUSTRY - SECONDARY PROCESSING Blow Molders Coating Film Pipe Pre-Plasticizers Rods Sheet Tubing PULLERS - BARGE HAUL PUMPS Centrifugal Proportioning Reciprocating Single Acting, 3 or more cylinders Double Acting, or more cylinders Rotary - Gear Lobe Vane RUBBER INDUSTRY Intensive Internal Mixers (a) Batch Mixers (b) Continuous Mixers Mixing Mill - Smooth Rolls - (If corrugated rolls are used, (then use the same service factors that are used for a Cracker-Warmer) Batch Drop Mill - Smooth Rolls Cracker Warmer - Roll: 1 Corrugated Roll Cracker - Corrugated Rolls Holding, Feed & Blend Mill - Rolls Refiner - Rolls Calenders SAND MILLER SEWAGE DISPOSAL Bar Screens Chemical Feeders Dewatering Screens Scum Breakers Slow or Rapid Mixers Sludge Collectors Thickeners Vacuum Filters SCREENS Air Washing Rotary - Stone or Gravel Traveling Water Intake SUGAR INDUSTRY Beet Slicer Cane Knives Crushers Mills (Low Speed End) TEXTILE INDUSTRY Batchers Calenders Cards Dry Cans Dryers Dyeing Machinery Looms Mangles Nappers Pads Slashers Soapers Spinners Tenter Frames Washers Winders Anti-Friction Bearings Only. NOTE: A Service Factor of 1.0 may be applied at the base of a super calender, operating over a speed range where part of the range is constant horsepower and part of the range is constant torque, provided that the constant horsepower part is greater than 1.5 to 1. A service factor of 1.5 is applicable to super calenders operating over the entire speed range at contant torque, or where the constant horsepower speed range is less than 1.5 to 1. B-109

110 LUBRICATION SPEED REDUCERS SERIES 000 The gearbox is filled with one of the following oils and fitted with a magnetic drain plug. Each gearbox is filled with oil according to the mounting position specified when ordered. (See page B-106) Synthetic lubricants are used in the gearbox due to their wide temperature range. In the event that the gearbox needs to be refilled, see the appropriate maintenance manual for the proper procedure and correct quantity of oil. If synthetic oil is not available check the chart below for acceptable non-synthetic lubricants. NO BACKSTOP Manufacturer -5 F to 15 F (-30 C to 50 C) COFRAN SINTOGEAR 15 MOBIL SHC 69 SHELL Omala HD 150 STANDARD SYNTHETIC GEAR OIL WITH BACKSTOP Manufacturer -5 F to 15 F (-30 C to 50 C) SHELL Omala RL 100 ACCEPTABLE MINERAL OIL LUBRICANTS - to 1 F 1 to 1 F(-10 C to 50 C) 1 F and Above Manufacturer (-0 C to 10 C) NO BACKSTOP WITH BACKSTOP (50 C +) ISO VG 68 ISO VG 100 ISO VG 150 ISO VG 0 ISO VG 150 ISO VG 30 COFRAN Mecanep 68 GL Cofraline Equitex 100 Mecanep 150 Equilux C000 Super Cofrapoid 80W 90 Mecanep 30 MOBIL Mobil Gear 66 Mobil Gear 67 Mobil Gear 69 Mobil Gear 630 DTE Extra Heavy Mobil Gear 63 SHELL Omala 68 Omala 100 Omala 150 Omala 0 Vitrea 150 Omala 30 Gear Frame OIL CAPACITIES (U.S. Quarts) Mounting Positions B3 B5 B6 B7 B8 B5 B53 B 5 V1(BS) V3 V5 V The Company names and the names of the Lubricants mentioned in the above tables are the tradenames, trademarks and logotypes of the respective companies, and are not owned by EPT. B-110

111 LUBRICATION SPEED REDUCERS SERIES 000 FOOT MOUNT COMBINED UNIT Gear Frame OIL CAPACITIES (U.S. Quarts) Mounting Positions B3 B8 B6 B7 V5 V6 P rim. S ec. P rim. S ec. P rim. S ec. P rim. S ec. P rim. S ec. P rim. Sec B-111

112 LUBRICATION SPEED REDUCERS SERIES 000 FLANGE MOUNT COMBINED UNIT Gear Frame OIL CAPACITIES (U.S. Quarts) Mounting Positions B5 V1 V3 P rim. S ec. P rim. S ec. P rim. Sec B-11

113 Experience the Power of EPT EDGE ONLINE EPT EDGE Online is the Web site's technical support center Also available "-7-365," these electronic tools provide for efficient drive design and product selection: ecatalog (an industry first) - an interactive, robust electronic "database" with over 100,000 part numbers Product Selection ( an industry first) - selection tools with extensive engineering efficiency benefits Smart Interchange - a dynamic tool that provides an intelligent interchange for competitive parts Media Library - electronically (PDF) viewable version of paper catalogs and documents, and downloadable installation and maintenance instructions CAD - an online service that allows users to view and upload a D or 3D CAD template drawing in a number of customer-compatible formats to be integrated into users' AutoCAD drawing (version 1-1) AutoCAD i s a registered trademark of Autodesk, Inc., which is not affiliated with Emerson Power Transmission. Connect here to experience "the power of EPT" B-113