User s Manual TECHNICAL DATA

Transcription

1 User s Manual TECHNICAL DATA Dimensins...23x28x33cm Weight...13kg Vltage VAC Pwer...330W Fuse A Max. temperature C Temperature range C Heating sleeve x 230 mm Max. press surface... 85x190mm Diameter f cups mm An autmatic mug-press fr cups with tw flexible jaws, which create abslute equal pressure. The device will pen autmatically when the press prcedure is cmpleted and lift the finished cup upwards ut f the heating sleeve s heating zne. The eur-patented pening mechanism makes sure that wrking is nw a lt mre cmfrtable. Optinal: - Crrectin sleeve fr cups 72 mm - Heating sleeve fr beer jugs 95 mm Lifting gear Flexible jaws Hating sleeve Pressure Adjustment Opening fr truble-free replacement f the heating sleeve Main switch Fuse 6A Lever t clse the press Pwer supply line 230VAC Case Display

2 Befre yu switch n the device, please check if yur scket is in prper cnditin and if the grunding wire is cnnected prperly. Afterwards yu have t read this USER`s MANUAL carefully. SWITCH ON The green tggle switch activates the press. The pilt lamp in the switch is shining. The display shws the current temperature f the heating sleeve and the red LED 1 is shining. The heating sleeve will heat immediately until the indicated initial temperature is reached. PRESSURE ADJUSTMENT Yu can change the pressure strength with the little knb n the left clamping jaw. Make sure the press is pen when regulating the pressure. Since yu cannt read ff the pressure yu will have t regulate manually in the first place. Afterwards yu d a hardprf test and if necessary change the pressure accrdingly. Never clse the press withut a cup! This may lead t verheating f the heating element! ATTENTION After each change yu shuld clse the press with a cup t check the new pressure setting. Damages due t excess pressure settings are excluded frm the guarantee. And therefre we assume n liability fr heating sleeves which have been damaged due t excess pressure. MAINTENANCE All maintenance wrks shuld be dne when the device is switched ff. Yu have t pull the plug ut f the scket befrehand. CLEANING The device shuld be cleaned with a sft clth. Use dmestic dish washing liquid r windw cleaning liquid. Scrubbing spnges, slvents r petrl are nt recmmended. Replacement f heating sleeve The press has t be cld! Use the main switch t turn ff the device and pull the plug ut f the scket. Open the plate at the back t replace the heating sleeve. Pull ut the little jack. Push the sleeve ut f the hlder and carefully pull ut the cnnectin cable. Take the new heating sleeve and carefully insert the cnnectin cable int the duct. Then yu have t clamp the new heating sleeve int the hlder. Cnnect the jack and clse the pening at the back f the device. Check if the sleeve is wrking prperly.

3 This press may nly be perated by trained staff after reading the user s manual. Settings 1. Push the cnfirmatin buttn fr 5 secnds until LED1 is blinking. 2. LED1 is blinking and the display shws the preset initial temperature. Prgramming mde has been switched n. 3. Use buttns + r - t set new initial temperature. Cnfirmatin + - LED 1 4. Push the cnfirmatin buttn. The display shws the preset press temperature. Use buttns + r -t set new press temperature. 4. Push the cnfirmatin buttn. The display shws the preset time. Use buttns + r -t set new time. 5. Push cnfirmatin buttn t deactivate prgramming mde. The press will apply the new settings. The settings will even be saved when the press is switched ff. Checking f adjusted settings The initial temperature f the heating sleeve is shwn n the display( press is pen). Push buttn + r - t check press temperature. The display will shw the currently adjusted press temperature. Push the - buttn t check the adjusted time. The display will shw the currently adjusted time setting. Example fr sublimatin: initial temperature 110 C press temperature 180 C time 240 sek. Cnfirmatin + - LED 1 Hw t insert cup Never clse the press withut a cup! This may lead t verheating f the heating element! Put the cup with the transfer nt the lifting gear and push it dwn. Put the cup in the middle f the sleeve befre yu clse the press. Release the lever. The press will pen autmatically when the press prcedure is cmpleted.

4 S10 Hauptschalter / Wlacznik glówny / main switch S1 time start (bialy / weiss / white ) F1 Sicherung / fuse 6A 230VAC L S10 0 N 1F25 FILTER F1 6A Netzteil / zasilacz / pwer supply unit 12 VDC F2 1,0A 230VAC - 12VDC + Rt/czerwny/red Blau/niebiesk/bluei schwarz/czarny SCHALTPLAN / POLACZEÑ Mug-O-matic SCHEMATIC (electrical diagram) DIGITAL THERMOREGULATOR Mug-O-Matic HEATER F S1 S + 12V C Weiss/bialy/white Weiss/bialy/white Schwarz/black Grün/green Braun/brazwy/brwn Rt/czerwny/red Rt/czerwny/red Elektrmagnet/ electr magnet mini-fit 4 pin Heizelement Grzalka heating element PT-100 Heizmanchette / plyta grzewcza / heating sleeve

5 TESTING REPORT E Base (paint, lubricatin, etc.) Heat and base platens, symmetry, silicne, tefln Hurs f wrk at 220 C... Electrical cnnectin, grunding wire, pwer cable Test with transfer fil Electrnics, max temperature 220 C, inspectin f all functins Warning stickers Hurs f wrk at 180 C... Packaging Temperature tlerance at 180 C...-/...+ C Serial number... EC declaratin f cnfrmity - Accrding t the EC directive 89/37 EC The Walter Schulze GmbH Schmalenbachstr Berlin hereby declares as Eurpean agent fr the manufacturer Rmanik that the fllwing described machine: heat press....serial number... accrds t the terms f the fllwing EC directives: Machine directive ( 89/37) Lw vltage directive (72/23) EMV-directive (89/336) Used standards and technical specificatins: EN 292-1, EN safety f machines EN electrical equipment f machines Berlin... Peter Meidinger CEO