DRAFT Testing and Reporting Requirements for Linear Replacement Lamps

Transcription

1 DRAFT Testing and Reprting Requirements fr Linear Replacement Lamps Nte: This draft represents updates t the existing Testing and Reprting Requirements fr Linear Replacement Lamps. All changes frm the existing language are highlighted in yellw. The DLC defines all tube-style LED prducts that use the lamp hlders (i.e. sckets r tmbstnes) in the luminaire t mechanically r electrically cnnect t the fixture husing and electric supply t fall under these testing requirements. Prducts that d nt emply lamp hlders will be classified as Retrfit Kits, regardless f frm factr. Please see the Prduct Eligibility page and Technical Requirements fr mre details n prduct classificatin. The DLC accepts QPL applicatins fr tw-ft, three-ft, fur-ft, eight-ft, and U-Bend Linear Replacement Lamps. The Testing and Reprting Requirements described belw are intended t evaluate the perfrmance bth f the lamp itself, and its perfrmance in an apprpriate reference fixture, representative f the mst cmmn applicatin fr each flurescent replacement lamp type. General Applicatins Under the Technical Requirements Table V4.3, linear replacement lamps will fall under ne f the fllwing seven General Applicatin designatins utlined belw. Tw-ft, three-ft, eight-ft, and U-bend replacement lamp general applicatins are restricted t LED lamps intended t replace flurescent T8. Fur-ft replacement lamp general applicatins are restricted t LED lamps intended t replace flurescent T8, T5, and T5HO lamps at this time. Prduct specificatin sheets must clearly indicate fr which specific linear replacement lamp type (i.e. T8, T5, r T5HO) the prduct is intended, and list the nminal length in inches and base type. DRAFT Testing and Reprting Requirements fr Linear Replacement Lamps Distributed via Octber 10, 2017 Page 1 f 18

2 T8 Tw-Ft Linear Replacement Lamps LED lamps intended t replace T8 flurescent lamps. These LED lamps shall be 24 inches lng and emply a G13 base. Marketing material shall indicate that they are intended t replace T8 flurescent lamps f the same length. Prducts f different lengths and bases are nt eligible. Prducts intended t perate n magnetic ballasts are nt eligible. T8 Three-Ft Linear Replacement Lamps LED lamps intended t replace T8 flurescent lamps. These LED lamps shall be 36 inches lng and emply a G13 base. Marketing material shall indicate that they are intended t replace T8 flurescent lamps f the same length. Prducts f different lengths and bases are nt eligible. Prducts intended t perate n magnetic ballasts are nt eligible. T8 Fur-Ft Linear Replacement Lamps LED lamps intended t replace T8 flurescent lamps. These LED lamps shall be 48 inches lng and emply a G13 base. Marketing material shall indicate that they are intended t replace T8 flurescent lamps f the same length. Prducts f different lengths and bases are nt eligible. Prducts intended t perate n magnetic ballasts are nt eligible. T5 Fur-Ft Linear Replacement Lamps LED lamps intended t replace T5 flurescent lamps (nte, nt T5 High Output r T5HO). These LED lamps shall be 46 inches lng and emply a G5 base. Marketing material shall indicate that they are intended t replace T5 flurescent lamps f the same length. Prducts f different lengths, bases, r marketed as intended t replace ther types f flurescent lamps will nt be eligible in this categry. T5HO Fur-Ft Linear Replacement Lamps LED lamps intended t replace T5HO flurescent lamps. These LED lamps shall be 46 inches lng and emply a G5 base. Marketing material shall indicate that they are intended t replace T5HO flurescent lamps f the same length. Prducts f different lengths, bases, r marketed as intended t replace ther types f flurescent lamps will nt be eligible in this categry. T8 Eight-Ft Linear Replacement Lamps LED lamps intended t replace T8 r T12 flurescent lamps. These LED lamps shall be 96 inches lng and emply a FA8 base. Marketing material shall indicate that they are intended t replace T8 r T12 flurescent lamps f the same length. DRAFT Testing and Reprting Requirements fr Linear Replacement Lamps Distributed via Octber 10, 2017 Page 2 f 18

3 Prducts f different lengths and bases are nt eligible. Prducts intended t perate n magnetic ballasts are nt eligible. U-Bend Replacement Lamps LED lamps intended t replace T8 flurescent lamps. These LED lamps shall emply a G13 base. Marketing material shall indicate that they are intended t replace T8 flurescent lamps. Prducts f different bases are nt eligible. Primary Use Designatins Under the Technical Requirements Table, replacement lamps will fall under ne f the fllwing fur Primary Use Designatins: Replacement Lamps (UL Type A): Tw-ft, three-ft, fur-ft, eight-ft, and U-bend LED "tubes" designed t replace tw-ft, three-ft, fur-ft, eight-ft, and U-bend flurescent lamps, respectively. Prducts in this categry emply lamp hlders t cnnect t the fixture being retrfitted and are designed t be "plug and play" replacements fr flurescent lamps. That is, prducts in this categry can perate ff an existing flurescent ballast, and d nt require mechanical r electrical changes t the fixture. Nte that due t testing cnsideratins, at this time nly prducts that can perate ff specific ballasts types are eligible. Please see Fixture Level Test requirements belw. Replacement lamps designed t perate ff magnetic ballasts r ther types f electrnic ballasts nt specified are nt eligible at this time. Internal Driver/Line Vltage Lamp-Style Retrfit Kits (UL Type B): Tw-ft, three-ft, fur-ft, eight-ft, and U-bend LED "tubes" designed t replace tw-ft, three-ft, fur-ft, eight-ft, and U-bend flurescent lamps, respectively. Prducts in this categry emply lamp hlders t cnnect t the fixture being retrfitted, but d nt perate ff the existing flurescent ballast. These prducts require rewiring f the existing fixture t bypass the ballast and send line vltage directly t the lamp hlders. External Driver Lamp-Style Retrfit Kits (UL Type C): Tw-ft, three-ft, fur-ft, eight-ft, and U-bend LED "tubes" designed t replace tw-ft, three-ft, fur-ft, eight-ft, and U-bend flurescent lamps, respectively. Prducts in this categry emply lamp hlders t cnnect t the fixture being retrfitted, d nt perate ff the existing DRAFT Testing and Reprting Requirements fr Linear Replacement Lamps Distributed via Octber 10, 2017 Page 3 f 18

4 flurescent ballast, and require rewiring f the existing fixture t replace the ballast with an external driver. The lamp hlders are then wired t receive nly the lw-vltage electricity that is supplied by that external driver. Dual Mde Internal Driver (UL Type A and Type B): Tw-ft, three-ft, fur-ft, eight-ft, and U-bend LED "tubes" designed t replace tw-ft, three-ft, fur-ft, eight-ft, and U-bend flurescent lamps, respectively. Prducts in this categry have the ability t perate ff the existing flurescent ballast and als have the ability t perate ff f line vltage if the trffer is rewired t bypass the ballast. These prducts cnnect t the trffer using standard pin-base cnnectins t the lamp hlders. Nte that due t testing cnsideratins, at this time nly prducts that can perate ff specific ballasts types are eligible. Please see testing requirements belw Replacement lamps designed t perate ff magnetic ballasts, r ff ther types f electrnic ballasts nt specified, are nt eligible at this time. Fr testing purpses, the DLC requires testing f bth the bare lamp and lamps installed in a typical fixture husing. These typical fixture husings are intended t prvide testing results f the mst cmmn applicatins in which these prducts are used, as well as representative thermal cnditins f the fixtures in which the lamps wuld be installed. In specifying these particular fixture husings, the DLC des nt endrse r exclude any particular make r mdel frame fr use in energy efficiency prgrams. Supprting Dcumentatin Applicants shall prvide the fllwing supprting dcumentatin in additin t the test data described belw. Installatin Instructins Installatin instructin sheets must be submitted with the applicatin t indicate hw the replacement lamp will be installed in an existing fixture in the field. This must be prvided in additin t all necessary dcumentatin required fr ther prduct categries. Lamps that require specialized cmpnents in rder fr installatin t perfrm t the abve criteria are nt eligible fr qualificatin. Lamps that emply rtatable end-caps are eligible, but must clearly indicate this feature in the prduct spec sheet. DRAFT Testing and Reprting Requirements fr Linear Replacement Lamps Distributed via Octber 10, 2017 Page 4 f 18

5 Safety Certificatin Dcumentatin Dcumentatin f safety certificatin fr the replacement lamp must be submitted with the applicatin. This dcumentatin must indicate safety certificatin has been btained. DLC staff will nt interpret safety testing as prf that safety certificatin has been btained. This must be prvided in additin t all necessary dcumentatin required fr ther prduct categries. Applicatin Review The DLC shall lg, analyze, and evaluate linear replacement lamp applicatins in accrdance with prcedures fllwed fr any individual fixture applicatin: 1) fr cmpleteness and accuracy f the filed applicatin data and 2) fr qualificatin accrding t DLC categry specificatins. Lamp Level Tests All lamps seeking qualificatin by the DLC must test the bare lamp accrding t LM- 79. Table 1: Individual Replacement Lamp Criteria: T8, T5, and T5HO Replacements Individual Lamp Criteria Tw-ft Lamps, T8 replacements Three-ft Lamps, T8 replacements Fur-ft Lamps, T8 replacements Fur-ft Lamps, T5 replacements Fur-ft Lamps, T5HO replacements Eight-ft Lamps, T8 replacements U-bend Lamps, T8 replacements System Efficacy 110 lm/w 110 lm/w 110 lm/w 110 lm/w 110 lm/w 110 lm/w 110 lm/w Initial Light Output 800 lm 1,200 lm 1,600 lm 1,600 lm 3,200 lm 3,200 lm 1,400 lm Crrelated Clr Temp. (CCT) Clr Rendering Index (CRI) 5000K 5000K 5000K 5000K 5000K 5000K 5000K Pwer Factr Ttal Harmnic Distrtin 20% 20% 20% 20% 20% 20% 20% DRAFT Testing and Reprting Requirements fr Linear Replacement Lamps Distributed via Octber 10, 2017 Page 5 f 18

6 Testing Ntes Fr T8 replacement lamps designed t perate ff existing flurescent ballasts, testing must be cnducted using a standard 0.88 ballast factr, electrnic instantstart ballast. Fr T5 and T5HO replacement lamps designed t perate ff existing flurescent ballasts, testing must be cnducted using a nrmal 1.0 ballast factr, electrnic prgrammed-start ballast. Specificatin sheets fr the ballasts used during testing must be prvided with the applicatin and the ballast make and mdel number must be nted in the test reprt. Ballasts used in testing must be certified t the applicable safety standards and must cmply with applicable ANSI standards. Fr lamp-style retrfit kits (i.e. prducts cnnecting mechanically and electrically via lamp hlders, but which require an electrical mdificatin t the existing fixture t bypass the existing ballast), "lamp"-level testing is als required. If the system is designed t perate multiple lamps ff an external driver, the driver shuld be laded as it wuld be in the field, with apprpriate steps taken t calculate the efficacy f the single lamp. Fr example, fr a tw-lamp kit, ne lamp shuld be measured fr light utput, while the system as intended (with tw identical lamps n the driver) shuld be measured fr electrical input. The wattage int the driver can then be divided by tw, and that wattage divided int the lamp lumens t determine system efficacy. Fr questins, please cntact inf@designlights.rg. Fixture Level Tests: Tw-Ft Linear Replacement Lamps Please nte that at this time lamps intended t replace T5-diameter flurescents are nly eligible in the fur-ft categries. Only lamps intended t replace T8 flurescents are currently eligible in the 2-ft categries. All lamps seeking qualificatin must be tested inside in a reference trffer. Type A, Type B, and Dual-mde tw-ft lamps shall test with three (3) lamps installed in an apprpriate reference trffer. Type C lamps shall test with the apprpriate number f lamps as are intended t be perated n the external driver included in that Type C system; tw-, three-, and fur-lamp Type C systems are eligible. The reference trffer may be any f the fllwing, r a pre-apprved equivalent: Lithnia 2GT8 lensed 2x2 Lithnia 2SP8 lensed 2x2 Lithnia 2PM3 9 cell 2x2 parablic Clumbia Lighting lensed 2x2 4PS22 DRAFT Testing and Reprting Requirements fr Linear Replacement Lamps Distributed via Octber 10, 2017 Page 6 f 18

7 Clumbia Lighting P222 9 cell 2x2 parablic Pre-apprved equivalent A.L.P. EL-2x2-20-* (*= # f lamps) Texas Flurescents 131-A-2-32U-E120 Mnmuth Lighting Crp RF24 Simkar Crpratin TY Lensed Trffer 2x2 Jun Lighting Grup S2x2BL LSI LA/FLA 2x2 Clumbia Lighting JT822 Visineering Crp. ERCTB 2x2 US Energy Sciences YTR-02-5 Pre-apprved Equivalents The DLC des nt endrse r exclude any particular make r mdel f reference fixture. Optins listed are intended t illustrate cmmn fixtures f the apprpriate type. Manufacturers may test in alternative fixtures t thse listed, with preapprval frm the DLC. Pre-apprved fixtures must meet the fllwing cnditins: Alternative fixtures must be cmmnly used in the applicatin categry intended fr which they are t be applied. Dcumentatin may be required t demnstrate fixtures apprpriate use if questins arise. Alternative fixtures must prvide similar thermal envirnments t thse listed. Particularly, alternative fixtures may nt be significantly different in internal vlume r cnstructin materials. DRAFT Testing and Reprting Requirements fr Linear Replacement Lamps Distributed via Octber 10, 2017 Page 7 f 18

8 Table 2: In-situ Testing Requirements: Tw-Ft Linear T8 Replacement Lamps In-situ Lamp Criteria fr Tw-Ft Linear Replacement Lamps Luminaire Efficacy 100 lm/w 2 lamps installed = 1,350 lm Minimum Initial Luminaire Light Output 3 lamps installed = 2,000 lm 4 lamps installed = 2,700 lm Spacing Criteria: = Spacing Criteria = Znal Lumen Distributin: 0-60 : 75% Lumen Maintenance L 70 50,000 hurs Lumen Maintenance LM-80 fr the package/mdule/array (6,000 hurs minimum) In-situ Temperature Measurement Test (ISTMT) in selected Reference Luminaire with three (3) identical lamps (nly ne is required t have thermcuple(s) attached) TM-21 Calculatr, apprpriately filled ut ( Testing Ntes Fr Replacement Lamps designed t perate ff existing flurescent ballasts, testing must be cnducted using a standard 0.88 ballast factr, electrnic instantstart ballast. Specificatin sheets fr the ballasts used during testing must be prvided with the applicatin and the ballast make and mdel number must be nted in the test reprt. Ballasts used in testing must be certified t the applicable safety standards, and must cmply with applicable ANSI standards. DRAFT Testing and Reprting Requirements fr Linear Replacement Lamps Distributed via Octber 10, 2017 Page 8 f 18

9 Replacement Lamps that utilize rtatable end caps shuld be tested in the rientatin specified as the default in the manufacturer s installatin instructins. If the installatin instructins d nt specify an rientatin, the lamps shuld be riented straight dwn (this is cmmnly the zer degree setting). DLC reviewers will review the installatin instructins prvided with the applicatin t verify the apprpriate testing rientatin, and cmpare this against dcumentatin in the LM-79 reprt and IES file. Rtatable end cap linear replacement lamp listings will include infrmatin n the testing rientatin in the Ntes field. Fixture Level Tests: Three-Ft Linear Replacement Lamps Please nte that at this time lamps intended t replace T5-diameter flurescents are nly eligible in the fur-ft categries. Only lamps intended t replace T8 flurescents are currently eligible in the 3-ft categries. All lamps seeking qualificatin must be tested inside in a reference strip fixture. Type A, Type B, and Dual-mde three-ft lamps shall test with tw (2) lamps installed in an apprpriate reference fixture. Type C lamps shall test with the apprpriate number f lamps as are intended t be perated n the external driver included in that Type C system; 1-, 2-, and 3 lamp Type C systems are eligible. The reference fixture may be any f the fllwing, r a pre-apprved equivalent: Lithnia C 2 25 MVOLT GEB10IS Lithnia Z 2 25 MVOLT GEB10IS Clumbia CS3-225-EU Clumbia CH3-225-EU Pre-apprved equivalent Pre-apprved Equivalents The DLC des nt endrse r exclude any particular make r mdel f reference fixture. Optins listed are intended t illustrate cmmn fixtures f the apprpriate type. Manufacturers may test in alternative fixtures t thse listed, with preapprval frm the DLC. Pre-apprved fixtures must meet the fllwing cnditins: Alternative fixtures must be cmmnly used in the applicatin categry intended t be applied fr. Dcumentatin may be required t demnstrate fixtures apprpriate use if questins arise. DRAFT Testing and Reprting Requirements fr Linear Replacement Lamps Distributed via Octber 10, 2017 Page 9 f 18

10 Alternative fixtures must prvide similar thermal envirnments t thse listed. Particularly, alternative fixtures may nt be significantly different in internal vlume r cnstructin materials. Table 3: In-situ Lamp Criteria fr Three-Ft Linear Replacement Lamps In-situ Lamp Criteria fr Three-Ft Linear Replacement Lamps Luminaire Efficacy 100 lm/w Minimum Initial Luminaire Light Output 2 lamps installed x 2,200 lm 3 lamps installed x 3,200 lm Spacing Criteria: = Spacing Criteria = Znal Lumen Distributin: 0-60 : 75% Lumen Maintenance L 70 50,000 hurs Lumen Maintenance LM-80 fr the package/mdule/array (6,000 hurs minimum) In-situ Temperature Measurement Test (ISTMT) in selected Reference Luminaire with tw (2) identical lamps (nly ne is required t have thermcuple(s) attached) TM-21 Calculatr, apprpriately filled ut ( Testing Ntes Fr Replacement Lamps designed t perate ff existing flurescent ballasts, testing must be cnducted using a standard 0.88 ballast factr, electrnic instantstart ballast. Specificatin sheets fr the ballasts used during testing must be prvided with the applicatin and the ballast make and mdel number must be DRAFT Testing and Reprting Requirements fr Linear Replacement Lamps Distributed via Octber 10, 2017 Page 10 f 18

11 nted in the test reprt. Ballasts used in testing must be certified t the applicable safety standards, and must cmply with applicable ANSI standards. Replacement Lamps that utilize rtatable end caps shuld be tested in the rientatin specified as the default in the manufacturer s installatin instructins. If the installatin instructins d nt specify an rientatin, the lamps shuld be riented straight dwn (this is cmmnly the zer degree setting). DLC reviewers will review the installatin instructins prvided with the applicatin t verify the apprpriate testing rientatin, and cmpare this against dcumentatin in the LM-79 reprt and IES file. Rtatable end cap linear replacement lamp listings will include infrmatin n the testing rientatin in the Ntes field. Fixture Level Tests: Fur-Ft Linear Replacement Lamps All T8 and T5 replacement lamps seeking qualificatin must be tested inside a reference trffer. Type A, Type B, and Dual-mde fur-ft lamps shall test with tw (2) lamps installed in an apprpriate reference trffer. Type C lamps shall test with the apprpriate number f lamps as are intended t be perated n the external driver included in that Type C system; 2, 3, and 4 lamp Type C systems are eligible. The reference trffer may be any f the fllwing, r a pre-apprved equivalent: Lithnia 2GT8 lensed 2x4 (T8 replacements) Lithnia SP5 lensed 2x4 (T5 replacements) Lithnia 2PM3N 12 cell 2x4 parablic (T8 r T5 versin, as apprpriate) Clumbia Lighting lensed 4PS24 (T8 r T5 versin, as apprpriate) Clumbia Lighting P cell parablic (T8 r T5 versin, as apprpriate) Pre-apprved equivalent A.L.P. EL-2x4-23-* (*= # f lamps) Lithnia 2SP8 G 2 32 A12 XXXX XX XXXX Texas Flurescents 131-A-4-32-E120 Clumbia Lighting 4PS24 Mnmuth Lighting Crp DCP 22 Simkar Crpratin TY Lensed Trffer 2x4 Jun Lighting Grup S2x4BL DRAFT Testing and Reprting Requirements fr Linear Replacement Lamps Distributed via Octber 10, 2017 Page 11 f 18

12 LSI GA 2x4 Clumbia Lighting JT824 Visineering Crp. ERCTB 2x4 US Energy Sciences YTR-04-7 Philips Day-Brite 2SPG232-FS01-UNV-1/2EB All T5HO replacement lamps seeking qualificatin must be tested inside a reference high bay. Type A, Type B, and Dual-mde fur-ft lamps shall test with fur (4) lamps installed in an apprpriate reference high bay. Type C lamps shall test with the apprpriate number f lamps as are intended t be perated n the external driver included in that Type C system; 3, 4, and 6 lamp Type C systems are eligible. The reference trffer may be any f the fllwing, r a pre-apprved equivalent: Lithnia IBZT5 4 high bay Clumbia Lighting LHA4-4 (T5HO versin) Pre-apprved equivalent Pre-apprved Equivalents The DLC des nt endrse r exclude any particular make r mdel f reference fixture. Optins listed are intended t illustrate cmmn fixtures f the apprpriate type. Manufacturers may test in alternative fixtures t thse listed, with preapprval frm the DLC. Pre-apprved fixtures must meet the fllwing cnditins: Alternative fixtures must be cmmnly used in the applicatin categry intended t be applied fr. Dcumentatin may be required t demnstrate fixtures apprpriate use if questins arise. Alternative fixtures must prvide similar thermal envirnments t thse listed. Particularly, alternative fixtures may nt be significantly different in internal vlume r cnstructin materials. DRAFT Testing and Reprting Requirements fr Linear Replacement Lamps Distributed via Octber 10, 2017 Page 12 f 18

13 Table 4: In-situ Testing Requirements: Fur-Ft Linear T8, T5, and T5HO Replacement Lamps In-situ Lamp Criteria Luminaire Efficacy Minimum Initial Luminaire Light Output Fur-Ft Linear T8 and T5 Replacement Lamps 100 lm/w 2 lamps installed = 3,000 lm 3 lamps installed = 4,500 lm 4 lamps installed = 6,000 lm Fur-Ft Linear T5HO Replacement Lamps 105 lm/w 3 lamps installed = 7,500 lm 4 lamps installed = 10,000 lm 6 lamps installed = 15,000 lm Spacing Criteria Spacing Criteria: = = Znal Lumen Distributin: 0-60 : 75% Znal Lumen Distributin: : 30% Lumen Maintenance L70 50,000 hurs 50,000 hurs Lumen Maintenance LM-80 fr the package/mdule/array (6,000 hurs minimum) In-situ Temperature Measurement Test (ISTMT) in selected Reference Luminaire with lamps installed per the in-luminaire testing described in the previus sectin (nly httest ne is required t have thermcuple(s) attached) TM-21 Calculatr, apprpriately filled ut ( Testing Ntes Fr T8 replacement lamps designed t perate ff existing flurescent ballasts, testing must be cnducted using a standard 0.88 ballast factr, electrnic instantstart ballast. Specificatin sheets fr the ballasts used during testing must be prvided with the applicatin and the ballast make and mdel number must be nted in the test reprt. Ballasts used in testing must be certified t the applicable safety standards, and must cmply with applicable ANSI standards. DRAFT Testing and Reprting Requirements fr Linear Replacement Lamps Distributed via Octber 10, 2017 Page 13 f 18

14 Fr T5 and T5HO replacement lamps designed t perate ff existing flurescent ballasts, testing must be cnducted using a nrmal 1.0 ballast factr, electrnic prgrammed-start ballast. Specificatin sheets fr the ballasts used during testing must be prvided with the applicatin and the ballast make and mdel number must be nted in the test reprt. Ballasts used in testing must be certified t the applicable safety standards, and must cmply with applicable ANSI standards. Prduct specificatin sheets must clearly indicate fr which specific linear replacement lamp type (i.e. T8, T5, r T5HO) the prduct is intended, and list the nminal length in inches and base type. Replacement Lamps that utilize rtatable end caps shuld be tested in the rientatin specified as the default in the manufacturer s installatin instructins. If the installatin instructins d nt specify an rientatin, the lamps shuld be riented straight dwn (this is cmmnly the zer degree setting). DLC reviewers will review the installatin instructins prvided with the applicatin t verify the apprpriate testing rientatin, and cmpare this against dcumentatin in the LM-79 reprt and IES file. Rtatable end cap linear replacement lamp listings will include infrmatin n the testing rientatin in the Ntes field. Fixture Level Tests: Eight-Ft Linear Replacement Lamps All eight-ft T8 replacement lamps seeking qualificatin must be tested inside a reference strip fixture using an apprpriate integrating sphere. Additinally, using a gniphtmeter, tw fur-ft linear replacement lamps with identical cnstructin as half f the eight-ft linear replacement lamp must be tested inside a reference strip fixture. The gniphtmeter testing results frm the fur-ft strip fixture shall be extraplated t represent an eight-ft strip fixture by multiplying ttal lumens, znal lumens, and wattage by 2, and the results must meet the in-situ testing requirements in Table 5. Applicants must reprt results frm eight-ft testing in the integrating sphere, results frm fur-ft testing in the gniphtmeter, and prvide clear calculatin f extraplatin f the fur ft testing t eight-ft results. The tw fur-ft linear replacement lamps must have identical crss-sectin cnstructin, including having the same type and quantity f driver(s) at same drive current, same number f LEDs r LED bards, LED layut, spacing, plastic tube material, thickness, and aluminum extrusin. Manufacturers must prvide a pht f the eight-ft and fur-ft LED layut side-by-side and as well as a crss sectin diagram f cnstructin fr bth prducts. DRAFT Testing and Reprting Requirements fr Linear Replacement Lamps Distributed via Octber 10, 2017 Page 14 f 18

15 Type A, Type B, and dual mde eight-ft lamps shall test with tw (2) lamps installed in an apprpriate reference strip. Type C lamps shall test with the apprpriate number f lamps as are intended t be perated n the external driver included in that Type C system; 1, and 2 lamp Type C systems are eligible. The eight-ft reference strip may be any f the fllwing, r a pre-apprved equivalent: Lithnia C 2 96T8 MVOLT GEB10IS Clumbia CS8-296T8-EU Texas Flurescent C 259 MV Pre-apprved equivalent The fur-ft reference strip may be any f the fllwing, r a pre-apprved equivalent: Lithnia C 2 32 MV Clumbia CS4-232-EU Texas Flurescent C MV Pre-apprved equivalent Pre-apprved Equivalents The DLC des nt endrse r exclude any particular make r mdel f reference fixture. Optins listed are intended t illustrate cmmn fixtures f the apprpriate type. Manufacturers may test in alternative fixtures t thse listed, with preapprval frm the DLC. Pre-apprved fixtures must meet the fllwing cnditins: Alternative fixtures must be cmmnly used in the applicatin categry intended t be applied fr. Dcumentatin may be required t demnstrate fixtures apprpriate use if questins arise. Alternative fixtures must prvide similar thermal envirnments t thse listed. Particularly, alternative fixtures may nt be significantly different in internal vlume r cnstructin materials. DRAFT Testing and Reprting Requirements fr Linear Replacement Lamps Distributed via Octber 10, 2017 Page 15 f 18

16 Table 5: In-situ Testing Requirements: Eight-Ft Linear T8 Replacement Lamps In-situ Lamp Criteria Eight-Ft Linear T8 Replacement Lamps Luminaire Efficacy Minimum Initial Luminaire Light Output Spacing Criteria Lumen Maintenance L lm/w 2 lamps installed = 6,000 lm Spacing Criteria: = = Znal Lumen Distributin: 0-60 : 75% 50,000 hurs Lumen Maintenance LM-80 fr the package/mdule/array (6,000 hurs minimum) In-situ Temperature Measurement Test (ISTMT) in selected Reference Luminaire with lamps installed per the in-luminaire testing described in the previus sectin (nly httest ne is required t have thermcuple(s) attached) TM-21 Calculatr, apprpriately filled ut ( Testing Ntes Fr T8 replacement lamps designed t perate ff existing flurescent ballasts, testing must be cnducted using a standard 0.88 ballast factr, electrnic instantstart ballast. Specificatin sheets fr the ballasts used during testing must be prvided with the applicatin and the ballast make and mdel number must be nted in the test reprt. Ballasts used in testing must be certified t the applicable safety standards, and must cmply with applicable ANSI standards. Replacement Lamps that utilize rtatable end caps shuld be tested in the rientatin specified as the default in the manufacturer s installatin instructins. If the installatin instructins d nt specify an rientatin, the lamps shuld be riented straight dwn (this is cmmnly the zer degree setting). DLC reviewers will review the installatin instructins prvided with the applicatin t DRAFT Testing and Reprting Requirements fr Linear Replacement Lamps Distributed via Octber 10, 2017 Page 16 f 18

17 verify the apprpriate testing rientatin, and cmpare this against dcumentatin in the LM-79 reprt and IES file. Rtatable end cap linear replacement lamp listings will include infrmatin n the testing rientatin in the Ntes field. Fixture Level Tests: U-bend Replacement Lamps All lamps seeking qualificatin must be tested inside in a reference trffer. Type A, Type B, and dual mde U-bend lamps shall test with tw (2) lamps installed in an apprpriate reference trffer. The reference trffer may be any f the fllwing, r a pre-apprved equivalent: Lithnia 2GT8 lensed 2x2 Lithnia 2SP8 lensed 2x2 Lithnia 2PM3 9 cell 2x2 parablic Clumbia Lighting lensed 4PS22 Clumbia Lighting P222 9 cell parablic Pre-apprved equivalent A.L.P. EL-2x2-20-* (*= # f lamps) Texas Flurescents 131-A-2-32U-E120 Mnmuth Lighting Crp RF24 Simkar Crpratin TY Lensed Trffer 2x2 Jun Lighting Grup S2x2BL LSI LA/FLA 2x2 Clumbia Lighting JT822 Visineering Crp. ERCTB 2x2 US Energy Sciences YTR-02-5 Pre-apprved Equivalents The DLC des nt endrse r exclude any particular make r mdel f reference fixture. Optins listed are intended t illustrate cmmn fixtures f the apprpriate type. Manufacturers may test in alternative fixtures t thse listed, with preapprval frm the DLC. Pre-apprved fixtures must meet the fllwing cnditins: Alternative fixtures must be cmmnly used in the applicatin categry intended t be applied fr. Dcumentatin may be required t demnstrate fixtures apprpriate use if questins arise. DRAFT Testing and Reprting Requirements fr Linear Replacement Lamps Distributed via Octber 10, 2017 Page 17 f 18

18 Alternative fixtures must prvide similar thermal envirnments t thse listed. Particularly, alternative fixtures may nt be significantly different in internal vlume r cnstructin materials. Table 6: In-situ Testing Requirements: U-bend Linear Replacement Lamps In-situ Lamp Criteria fr U-bend Linear Replacement Lamps Luminaire Efficacy Minimum Initial Luminaire Light Output Spacing Criteria Lumen Maintenance L lm/w 2 lamps installed: 2,500 lm 3 lamps installed: 3,750 lm Spacing Criteria: = = Znal Lumen Distributin: 0-60 : 75% 50,000 hurs Lumen Maintenance LM-80 fr the package/mdule/array (6,000 hurs minimum) In-situ Temperature Measurement Test (ISTMT) in selected Reference Luminaire with tw (2) identical lamps (nly ne is required t have thermcuple(s) attached) TM-21 Calculatr, apprpriately filled ut ( Testing Ntes Fr Replacement Lamps designed t perate ff existing flurescent ballasts, testing must be cnducted using a standard 0.88 ballast factr, electrnic instantstart T8 ballast. Specificatin sheets fr the ballasts used during testing must be prvided with the applicatin and the ballast make and mdel number must be nted in the test reprt. DRAFT Testing and Reprting Requirements fr Linear Replacement Lamps Distributed via Octber 10, 2017 Page 18 f 18