SMB Amphenol. 50 ohm Coaxial Connectors Specifications 36 Plugs 37 Jacks 38 Bulkhead Receptacles PCB Receptacles 41-43
|
|
|
- Godfrey Pitts
- 5 years ago
- Views:
Transcription
1 Description The name derives from SubMiniature B (the second subminiature design). The was developed in the 1960 s. is a smaller version of the SMA with snap-on coupling. Amphenol s connectors conform to the requirements of MIL-C and their interface is in compliance with MIL-STD-348. Available in 50 & 75 ohm impedance provides broadband capability through 4 GHz with a snap-on connector design and utilizes die cast components on non-critical areas to provide a low cost solution. Features and Benefits Broadband performance with low reflection DC to 4 GHz provides low cost connector combined with high quality. Quick connect/disconnect snap-on mating reduces installation time. Availability in 50 Ohm, 75 Ohm & High Density 75 Ohm ensures customer a solution to specific applications. Various plating options: Nickel, Gold, Tin Lead. Also selective plating provides corrosion resistance finish as well as good solderability characteristics. PCB slide-on plug and jack allows board to board mounting with a low insertion force. Ideal for mating a high number of connectors on a pair of PCBs. Application Antennas Automotive (GPS) Base Stations Cable Assemblies Components Instrumentation PC/LAN Process Controls Radio Boards Surge Protection Telecom Test and Measurement Video Systems 50 ohm Coaxial Connectors Specifications 36 Plugs 37 Jacks 38 Bulkhead Receptacles PCB Receptacles ohm Coaxial Connectors Specifications 44 Plugs, Jacks 45 Receptacles, PCB ohm High Density Coaxial Connectors Specifications 47 Plugs 48 PCB Receptacles 49 35
2 C L Amphenol Specifications ELECTRICAL MECHANICAL ENVIRONMENTAL Impedance Frequency range Voltage rating for RG-188/U cables Dielectric withstanding voltage VSWR straight connectors rt. angle connectors straight connectors rt. angle connectors Contact resistance Insulation resistance RF leakage Insertion loss: straight connectors rt. angle connectors 50 ohms 0-4 GHz with low reflection; usable to 10.0 GHz. Sea level: 335 volts 70,000 ft: 85 volts 750 VRMS RG-196 type 1000 VRMS for RG-188 type RG-196/U series f (GHz) f (GHz) RG-188/U series f (GHz) f (GHz) Center contact: initial, 6.0 milliohms; After environmental, 8.0 Outer contact: initial, 1.0 milliohms; After environmental, 1.5 Braid to body: initial, 1.0 milliohms; After environmental, N/A 1000 megohms min. -55 db 2-3 GHz GHz GHz Mating Engagement forces Connector affixment to cable Cable affixment to center contact Contact captivation Cable retention Connector durability 50 ohm snap-on coupling, per MIL-STD-348 Initial 14 lbs. max. engagement. After 500 matings, 14 lbs. max engagement and disengagement. 2 lbs. min. disengagement. Braid and jacket: hex crimp. Solder All types, except as noted Equal to breaking strength of cable employed 500 mating and unmating cycles min. Temperature range -65 C to C Thermal shock 107 (test cond. B) except high temp C Vibration 204, snap-on (test cond. B) (15G's) Shock 213, snap-on (test cond. B) 75 6 milliseconds 1/2 sine. Corrosion 101 (test cond. B) 5% salt solution. MATERIAL Bodies Center contacts Outer contact Crimp ferrules Insulators Brass per QQB-626 or zinc per ASTM B86-71, as specified, nickel (or gold) plated as listed Female: beryllium copper, gold plated Male: brass or beryllium copper, gold plated Nickel or gold plated as listed. Annealed copper alloy TFE PLUG JACK.141/.131 REF PLANE.141 MIN.141 MIN.117 MIN REF PLANE.010 MAX.117 MAX.007 MAX.065 MIN ø.146 MAX ø.021/.019 ø.081 MAX ø.082 MIN.007/ MIN.064 MAX JACK.000 MIN.010 MIN.052 MIN 36
3 50 ohm Coaxial Connectors Fig. 1 Fig. 1A Fig. 1A 50Ω Plugs - Braid Crimp/Solder Female Contact P-51S Gold Plated RG-174,179, P-51S Gold Plated 187,188, P-51S Nickel Plated P-51S1 Nickel Plated P-51S Gold Plated P-51S Gold Plated RG-178, P-51S Gold Plated P-51S Nickel Plated P-51S Gold Plated P-51S1 Nickel Plated Dbl. Br. RG P-51S Gold Plated P-51S Gold Plated P-51S1 Nickel Plated 50 ohm PLUGS & ANGLE PLUGS 50Ω Angle Plugs - Braid Crimp/Solder Female Contact P-51A Gold Plated RG P-51A2 Gold Plated 179, 187, P-51A Nickel Plated 188, P-51A1 Nickel Plt. Body, Gold Plt Outer Cont P-51A2 Nickel Plated P-51A Gold Plated RG-178, P-51A1 Gold Plated P-51A Nickel Plated P-51A1 Nickel Plated Dbl. Br P-51A Nickel Plated RG P-51A2 Nickel Plated 50Ω Low Profile Angle Plugs, Braid Crimp/Solder Female Contact RG-174,179, 187,188, P-51A Gold Plated Cable Connector Cable Attachment c Dia. Amphenol RG-/U Description Outer Inner In. (mm) CAI Plt. Ins. Notes Number Fig..128(3.3) C60 P11 D1 Gold Plated Body P-51S 1 Plug Crimp Solder.128(3.3) C62 P11 D1 Gold Plated Body P-51S 1A.128(3.3) C60 P15 D1 Nickel Plated Body P-51S 1.128(3.3) C60 P15 D1 Nickel Plated Body P-51S1 1A.128(3.3) C60 P15 D1 Gold Plated Body P-51S 1A.128(3.3) C61 P11 D1 Gold Plated Body P-51A 2 RG-174,179,187,.128(3.3) C61 P11 D1 Gold Plated Body P-51A ,316 Angle Plug Crimp Solder.128(3.3) C61 P15 D1 Nickel Plated Body P-51A 2.128(3.3) C61 P15 D1 Nickel Plated Body P-51A (3.3) C61 P15 D1 Nickel Plated Body P-51A1 2 Low Profile Angle Plug Crimp Solder.128(3.3) C61 P26 D1 Nickel Plated Body P-51A 3.100(2.5) C60 P11 D1 Gold Plated Body P-51S 1 Plug Crimp Solder.100(2.5) C62 P11 D1 Gold Plated Body P-51S 1A.100(2.5) C60 P15 D1 Nickel Plated Body P-51S 1 RG-178, (2.5) C60 P15 D1 Gold Plated Body P-51S 1A.100(2.5) C60 P15 D1 Nickel Plated Body P-51S1 1A.100(2.5) C61 P11 D1 Gold Plated Body P-51A 2 Angle Plug Crimp Solder.100(2.5) C61 P11 D1 Gold Plated Body P-51A (2.5) C61 P15 D1 Nickel Plated Body P-51A 2.100(2.5) C61 P15 D1 Nickel Plated Body P-51A (3.6) C61 P22 D1 Nickel Plated Body P-51A 2 Angle Plug Crimp Solder Dbl. Braid (3.6) C61 P15 D1 Nickel Plated Body P-51A (3.6) C60 P11 D1 Gold Plated Body P-51S 1 Plug Crimp Solder.142(3.6) C60 P11 D1 Gold Plated Body P-51S 1A.142(3.6) C60 P15 D1 Nickel Plated Body P-51S1 1A Fig. 3 i.d. of outer crimp ferrule Gold plated outer contact Distributor stocked Diecast outer body Commercial grade 37
4 50 ohm Coaxial Connectors 50Ω Bulkhead Jacks Braid Crimp/Solder Male Contact RG-174,179, J-51S Gold Plated 187,188, 316 Dbl. Shield J-51S1 Gold Plated 50Ω Angle Bulkhead Jacks Braid Crimp/Solder Male Contact RG-174,179, 187,188, J-51A Gold Plated Dbl. Shield J-51A2 Gold Plated 50 ohm BULKHEAD & ANGLE BULKHEAD JACKS Cable Connector Cable Attachment c Dia. MTG Amphenol RG-/U Description Outer Inner In. (mm) Hole CAI Plt. Ins. Notes Number Fig. RG-174,179,187, Bulkhead Jack Crimp Solder.128(3.3) P C60 P15 D1 Gold Plated Body J-51S 1 188,316 Angle Bulkhead Jack Crimp Solder.128(3.3) P C61 P11 D1 Gold plated Body J-51A 2 Dbl. Shield 316 Distributor stocked Bulkhead Jack Crimp Solder.142(3.6) P C60 P15 D1 Gold Plated Body J-51S1 1 Bulkhead Jack Crimp Solder.142(3.6) P C61 P15 D1 Gold Plated Body J-51A2 2 Commercial grade 38
5 50 ohm Bulkhead Receptacles Fig. 1 Fig. 2 Bulkhead Receptacle-Rear Mount Male Contact/Solder Cup Terminal J-51R Gold Plated Bulkhead Receptacle-Front Mount Male Contact/Solder Cup Terminal J-51R Gold Plated Fig. 3 Bulkhead Receptacle Front Mount Male Contact/Post Terminal J-51R Gold Plated Jam Nut for Receptacles Gold Plated Nickel Plated Lockwasher for Receptacles Gold Plated Nickel Plated 50 ohm BULKHEAD JACK RECEPTACLES & ACCESSORIES captive male contacts Connector Terminal MTG Construction Amphenol Description Type Hole Plt. Ins Notes Number Fig. Bulkhead Jack Receptacle, Rear Mount Solder Cup P P9 D1 Gold Plated Body J-51R 1 Bulkhead Jack Receptacle, Front Mount Solder Cup P P11 D1 Gold Plated Body J-51R 2 Bulkhead Jack Receptacle, Front Mount Blunt Post P P9 D1 Gold Plated Body J-51R 3 Jam Nut See Fig , -2 3 Lockwasher See Fig , -2 3 Distributor stocked Jam Nut and Lockwasher sold separately. Commercial grade 39
6 50 ohm Bulkhead Receptacles Recessed Bulkhead Jack Receptacle Front Mount/Male Contact/Solder Cup Terminal J-51R Gold Plated Angle Bulkhead Jack Receptacle Front Mount/Male Contact/Solder Cup Terminal J-51R Gold Plated 50 ohm BULKHEAD JACK RECEPTACLES captive male contacts Connector Terminal MTG Construction Amphenol Description Type Hole Plt. Ins Notes Number Fig. Recessed Bulkhead Jack Receptacle, Front Mount Solder Cup X P11 D1 Gold Plated Body J-51R 1 Angle Bulkhead Jack Receptacle, Front Mount Solder Cup P P11 D1 Gold Plated Body J-51R 2 Distributor stocked Jam Nut and Lockwasher sold separately 40
7 50 ohm PCB Receptacles PCB Slide-on Board-to-Board Interconnect for.360"(9mm) Bd. Spacing Plug: P-53P Gold Plated Jack: J-53P Gold Plated PCB Bulkhead Jack Receptacle Male Contact/Post Terminal/Four Legs J-53P Nickel Plated 50 ohm BULKHEAD JACK AND PRINTED CIRCUIT RECEPTACLES captive male contacts Connector Terminal MTG Construction Amphenol Description Type Hole Plt. Ins Notes Number Fig. PCB Slide-on Board-to-Board Interconnect Plug/Gold Plated P-53P Blunt Post T P9 D1 for.360"(9mm) Bd. Spacing/Four Legs Jack/Gold Plated J-53P 1 PCB Bulkhead Jack Receptacle/,Four Legs Blunt Post T/P P6 D1 Nickel Body/No Stand-off Pads J-53P 2 41
8 50 ohm PCB Receptacles PCB Angle Bulkhead Receptacle Male Contact/Four Legs/Leak Tight J-51A Tin Lead Plated Cube Body & Legs, Gold Plated Interface & Contact PCB Angle Bulkhead Receptacle Male Contact/Four Legs/No Stand-off Pads J-51A Tin Lead Plated Cube Body & Legs, Gold Plated Interface & Contact Fig. 3 PCB Angle Jack Receptacle Male Contact/Four Legs/Leak Tight J-51A Tin Lead Plated Cube Body & Legs, Gold Plated Interface & Contact 50 ohm BULKHEAD JACK AND PRINTED CIRCUIT RECEPTACLES captive male contacts Connector Terminal MTG Construction Amphenol Description Type Hole Plt. Ins Notes Number Fig. PCB Angle Bulkhead Jack Receptacle, Tin Lead Plt. Cube Body & Legs Blunt Post T/Q P16 D1 Four Legs/Leak Tight Gold Plt. Interface & Contact J-51A 1 PCB Angle Bulkhead Jack Receptacle, Tin Lead Plt. Cube Body & Legs Blunt Post T/Q P16 D1 Four Legs/No Stand-off Pads Gold Plt. Interface & Contact J-51A 2 PCB Angle Jack Receptacle Tin Lead Plt. Cube Body & Legs Blunt Post T P16 D1 Four Legs/Leak Tight Gold Plt. Interface & Contact J-51A 3 Distributor stocked Commercial grade 42
9 50 ohm PCB Receptacles.295 (7.49).250 (6.35).155 (3.94).020 (0.51).200 (5.08).100 (2.54).060 ( (1.65).040 (1.02) Sq.095 (2.41).105 (2.67).020 (0.51) Dia PCB Receptacle Jack Post Terminal/Four Legs J-51P Gold Plated J-51P3 Tin Plated Body & Legs J-51P2 Gold Plated.250 (6.35) Sq 50Ω PCB End Mount Jack Receptacle Male Contact/Blunt Post Terminal J-51P Gold Plated Gold Plated Contact Fig. 3 Fig /-.002 (1.27) dia..290 (7.37).450 (11.4).031 (.787).038 (.965)Dia.450 (11.4).225 (5.71).155 (3.94).255 (6.48) Sq.040 (1.02) Sq.358 (9.09) Dia.056 (1.65) D.257 (6.53) Dia.070 (1.78).065 (1.65).250 SQ PCB Jack Receptacle Board Lock J-51P Tin Lead Plt Body, Gold Plated Contact.070 (1.78).025 (.635) (5.08) PCB Receptacle Jack Board Lock J-51P Gold Plated J-51P1 Nickel Plated 50 ohm PRINTED CIRCUIT RECEPTACLES Connector Terminal MTG Construction Amphenol Description Type Hole Plt. Ins Notes Number Fig. Gold Plated Body J-51P P11 PCB Jack Receptacle/Four Legs Blunt Post T D1 Gold Plated Body J-51P2 1 P6 Tin Plated Body, Gold Plt. contact J-51P3 PCB Bulkhead Jack Receptacle/,Four Legs Blunt Post T P9 D1 Gold Plt. Body J-51P 2 PCB Bulkhead Jack Receptacle/,Four Legs Blunt Post T P9 D1 Tin Lead Plt Body, Gold Plt. contact J-51P 3 PCB Bulkhead Jack Receptacle Board Lock T P11 D1 Gold Plated Body J-51P PCB Bulkhead Jack Receptacle Board Lock T P11 D1 Nickel Plated Body J-51P1 4 Distributor stocked Die cast outer body 43
10 75 ohm Coaxial Connectors Amphenol standard 75 ohm 903 series connectors are constructed in accordance with the requirements of MIL-C and their interface is in compliance with MIL-STD-348. These subminiature units feature positive lock mating as well as snap-on mating faces. They are available in a variety of configurations and styles. This series has broadband performance with low reflection. MATERIAL Bodies Center contacts Outer contact Crimp ferrules Insulators Brass per QQB-626, as specified, nickel (or gold) plated as listed Female: beryllium copper, gold plated Male: brass or beryllium copper, gold plated Nickel or gold plated as listed. Annealed copper alloy TFE SPECIFICATIONS ELECTRICAL Impedance Frequency range Voltage rating for RG-188/U cables Dielectric withstanding voltage RF high potential withstanding voltage Corona level VSWR straight connectors right angle connectors Contact resistance Insulation resistance: RF leakage Insertion loss: straight right angle 75 ohms 0-4 GHz with low reflection; usable to 10.0 GHz. Sea level: 335 volts 70,000 ft: 85 volts 1,000 VRMS RG-195/U series 500 VRMS RG-195/U series 400 min. 70K ft. RG-196/U series f (GHz) RG-188/U series f (GHz) RG-196/U series f (GHz) RG-188/U series f (GHz) Center contact: initial, 6.0 milliohms; After environmental, 8.0 Outer contact: initial, 1.0 milliohms; After environmental, 1.5 Braid to body: initial, 1.0 milliohms; After environmental, N/A 1000 megohms min. -55 db 2-3 GHz GHz GHz * These characteristics are typical and may not apply to all connectors. This series is also called SMZ. MECHANICAL Mating Engagement forces Connector affixment to cable Cable affixment to center contact Contact captivation Cable retention Connector durability ENVIRONMENTAL 75 ohm snap-on coupling, per MIL-STD-348 Initial 14 lbs. max. engagement. After 500 matings, 14 lbs. max engagement and disengagement. 2 lbs. min. disengagement. Braid and jacket: hex crimp. Solder All types, except as noted Equal to breaking strength of cable employed 500 mating and unmating cycles min. Temperature range -65 C to C Thermal shock 107 (test cond. B) except high temp C Vibration 204, snap-on (test cond. B) (15G's) Shock 213, snap-on (test cond. B) 75 6 milliseconds 1/2 sine. Corrosion 101 (test cond. B) 5% salt solution. PLUG JACK.141/.131 REF PLANE.141 MIN.141 MIN.117 MIN REF PLANE.010 MAX.117 MAX.007 MAX.065 MIN ø.244 MAX ø.021/.019 ø.130 MAX ø.131 MIN.007/ MIN.064 MAX.000 MIN.010 MIN.052 MIN 44
11 75 ohm Coaxial Connectors Fig. 1 Fig. 1 Fig. 2 Fig. 1A Fig. 1A.900 MAX. (22.9) (.375) (9.53) 75Ω Plug Braid Crimp/Solder Female Contact P-71S7 Positive Lock for 735A Cable P-71S Positive Lock for RG-180, 195 Gold Plated Body, Nickel Plt. Cpl. Ring P-71S3 Positive Lock for RG-179 Gold Plated Body, Nickel Plt. Cpl. Ring P-71S Positive Lock for RD P-71S Positive Lock for RG-179 c dia. ø.104 (2.64) ø.360 (9.14) 75Ω Plug Braid Crimp/Solder Female Contact/Gold Plt P-71S for RG-179, Nickel Plated Body Fig. 3 Fig. 4 c dia. 75Ω Angle Plug Braid Crimp/Solder Female Contact P-71A Positive Lock for Belden 1694A RG-6 Type, Gold Plated Body, Nickel Plt. Cpl. Ring 75 ohm PLUGS, ANGLE PLUGS & BULKHEAD JACKS 75Ω Bulkhead Jack Braid Crimp/Solder Male Contact/Gold Plated J-71S for RG-179 Cable Connector Cable Attachment c Dia MTG Amphenol RG-/U Description Outer Inner In. (mm) Hole CAI Plt. Ins. Notes Number Fig. RG-179 Bulkhead Jack Crimp Solder.128(3.3) R C60 P9 D1 Gold Plated Body J-71S 4 Plug (Positive Lock) Crimp Solder.128 (3.3) C60 P9 D1 Nickel Plt coupling Ring P-71S3 1 Plug (Positive Lock) Crimp Solder.128 (3.3) C60 P9 D1 Nickel Plt coupling Ring P-71S 1A RD-179 Plug (Positive Lock) Crimp Solder.128 (3.3) C60 P9 D1 Nickel Plt coupling Ring P-71S 1A RG-174, 179, Nickel Plated Body Plug Crimp Solder.128(3.3) C60 PCF D1 187, 188, 316 Nickel Plt Coupling Ring P-71S 2 RG-180, 195 Plug (Positive Lock) Crimp Solder.180(4.6) C60 PCF D1 Gold Plated Body Nickel Plt Coupling Ring P-71S 1 Amphenol Angle Plug (Positive Lock) Crimp Solder.300(7.6) C61 PCF D1 Gold Plated Body P-71A A Plug (Positive Lock) Crimp Solder.175(4.4) C60 P9 D1 Gold Plated Body P-71S7 1 i.d. of outer crimp ferrule 45
12 75 ohm Coaxial Connectors 75Ω Bulkhead Receptacle/Rear Mount Male Contact/Solder Cup Terminal J-71R Gold Plated 75Ω Right Angle PCB Receptacle J-71A Gold Plated Fig. 3 Fig (9.07).025 (0.63).155 (3.94).038 Dia (0.96).375 (9.52) Dia.200 (5.08).100 (2.54).100 (2.54).200 (5.08).155 (3.94).025 (0.63).473 (12.0).318 (8.07).235 (5.97).250 (6.35) Sq.100 (2.54).200 (5.08).040 (1.02) Sq.038 (0.96) Dia.244 (6.20) Dia.070 (1.78) Sq.032 (0.81) Sq 75Ω PCB Plug Receptacle Female Contact/Four Legs P-71P Gold Plated 75Ω PCB Jack Receptacle Male Contact/Four Legs J-71P Gold Plated 75 ohm BULKHEAD & PRINTED CIRCUIT BOARD RECEPTACLES Connector Terminal MTG Construction Amphenol Description Type Hole Plt. Ins Notes Number Fig. Bulkhead Jack Receptacle, Rear Mount Solder Cup R P11 D1 Gold Plated/Captive Contact J-71R 1 PCB Plug Receptacle/Four Legs Blunt Post T P11 D1 Gold Plated/Captive Contact P-71P 3 PCB Jack Receptacle/Four Legs Blunt Post T P11 D1 Gold Plated/Captive Contact J-71P 4 PCB R/A Jack Receptacle/Four Legs Blunt Post T P11 D1 Gold Plated/Captive Contact J-71A 2 46
13 75 ohm High Density Coaxial Connectors Amphenol high density 75 ohm 903 Series connectors conform to the requirements of MIL-C and the interface is in compliance with MIL-STD-348. Features/Benefits Broadband capability through 4 GHz combines with compact, space saving design. Can easily be identified by their red Teflon insulators. Guided entry sleeve for positive mating. Closed entry contact to prevent "slide-by". Full range of high density connector configurations is available, including end launch, printed circuit board and cable connectors. Series gives design engineers options in applications where physical space is limited. SPECIFICATIONS ELECTRICAL Impedance Frequency range Voltage rating for RG-188/U cables Dielectric withstanding voltage VSWR straight right angle connectors Contact resistance Insulation resistance: RF leakage Insertion loss: straight rt. angle MATERIAL Bodies Center contacts Outer contact Crimp ferrules Insulators 75 ohms 0-4 GHz with low reflection Sea level: 335 volts 70,000 ft: 85 volts 750 VRMS, RG-196 type 1000 VRMS, RG-188 type 735A type f (GHz) f (GHz) Center contact: initial, 6.0 milliohms; After environmental, 8.0 Outer contact: initial, 1.0 milliohms; After environmental, 1.5 Braid to body: initial, 1.0 milliohms; After environmental, N/A 1000 megohms min. -55 db 2-3 GHz GHz GHz Brass per QQB-626 or zinc per ASTM B86-71, as specified, nickel (or gold) plated as listed beryllium copper, gold plated Nickel or gold plated as listed. Annealed copper alloy TFE - Red for I.D. MECHANICAL Mating Engagement forces Connector affixment to cable Cable affixment to center contact Contact captivation Cable retention Connector durability ENVIRONMENTAL 75 ohm snap-on coupling, per MIL-STD-348 Initial 14 lbs. max. engagement. After 500 matings, 14 lbs. max engagement and disengagement. 2 lbs. min. disengagement. Braid and jacket: hex crimp. Solder or crimp All types, except as noted Equal to breaking strength of cable employed 500 mating and unmating cycles min. Temperature range -65 C to C Thermal shock 107 (test cond. B) except high temp C Vibration 204, snap-on (test cond. B) (15G's) Shock 213, snap-on (test cond. B) 75 6 milliseconds 1/2 sine. Corrosion 101 (test cond. B) 5% salt solution. * These characteristics are typical and may not apply to all connectors. PLUG JACK REF. PLANE SPRING IS OPTIONAL DEPENDING ON CONTACT DESIGN.117 MIN. SHAPE OF TIP OPTONAL DIA..117 MAX..086 MIN..090 MIN..146 MAX MAX CONTACT REFERENCE PLANE.089 MAX. CLOSED ENTRY CONTACT 47
14 75 ohm High Density Coaxial Connectors 1.10 (27.9).550 (14.0).250 (6.35) Sq B A.500 (12.7).270 (6.86).250 (6.35) Dia.750 (19.0).630 (16.0).500 (12.7) B A 75Ω Plug P-71S for Type 735A P-71S for RG-179 Nickel Plated, Gold Plated Contact 75Ω Angle Plug P-71A for Type 735A P-71A for RG-179 Nickel Plated, Gold Plated Contact 75 ohm PLUGS & ANGLE PLUGS Cable Connector Cable Attachment c Dia Amphenol Fig. RG-/U Description Outer Inner A B CAI Plt. Ins. Notes Number A Type Plug Plug Crimp Crimp Solder Solder.128(3.3).167(4.24).152(3.86).214(5.43) C60 C60 PCF PCF D32 D32 Nickel Plated Body Nickel Plated Body P-71S P-71S 1 1 Angle Plug Angle Plug Crimp Crimp Solder Solder.128(3.3).167(4.24).152(3.86).214(5.43) C61 C61 PCF PCF D32 D32 Nickel Plated Body Nickel Plated Body P-71A P-71A
15 75 ohm High Density Coaxial Connectors.250 (6.35) Dia.525 (13.3).020 (5.13) Dia.250 (6.35) Sq.295 (7.49).250 (6.35).155 (3.94).020 (0.51).065 (1.65).040 (1.02) Sq.200 (5.08).100 (2.54).060 ( (2.41).105 (2.67).420 (10.6).110 (2.79) 75Ω PCB Slide-on Plug Receptacle Female Contact/Blunt Post Terminal P-71P Gold Plated TFE Fluorocarbon, Red Insulator Gold Plated Contact.040 (1.02).020 (0.51) Dia.250 (6.35) Sq 75Ω PCB End Mount Jack Receptacle Male Contact/Blunt Post Terminal J-71P Gold Plated TFE Fluorocarbon, Red Insulator Gold Plated Contact Fig. 3 Fig (11.4).295 (7.49).225 (5.71).155 (3.94).025 (0.63).020 (0.51) Dia.250 (6.35) Sq.100 (2.54).200 (5.08).040 (1.02) Sq.060 (1.52) Sq.500 (12.7).375 (9.52).405 (10.3).170 (4.32).110 (2.79).020 (0.51) Dia.040 (1.02).200 (5.08).250 (6.35).200 (5.08).250 (6.35) Sq 75Ω PCB Jack Receptacle Male Contact/Blunt Post Terminal J-71P Gold Plated TFE Fluorocarbon, Red Insulator Gold Plated Contact 75Ω PCB Angle Jack Receptacle Male Contact/Blunt Post Terminal J-71P Gold Plated Body TFE Fluorocarbon, Red Insulator Gold Plated Contact 75 ohm PRINTED CIRCUIT BOARD RECEPTACLES Connector Terminal MTG Construction Amphenol Description Type Hole Plt. Ins Notes Number Fig. PCB Slide-on Plug Receptacle/Four Legs Blunt Post T PCF D32 Gold Plt. Body/Red TFE Ins P-71P 1 PCB End mount Jack Receptacle/Four Legs Blunt Post PCF D32 Gold Plt. Body/Red TFE Ins J-71P 2 PCB Jack Receptacle/Four Legs Blunt Post T PCF D32 Gold Plt. Body/Red TFE Ins J-71P 3 PCB Angle Jack Receptacle/Four Legs Blunt Post T PCF D32 Gold Plt. Body/Red TFE Ins J-71P 4 49
MCX Amphenol. Description MCX. 50 Ohm Coaxial Connectors Specifications 18 Straight & Right Angle Crimp 19 Straight Solder & PCB 20-21
Description connectors conform to the European CECC 22220 Spec and was introduced in the 1980 s. While the uses identical inner contact and insulator dimensions as the SMB, the outer diameter of the plug
Bodies Brass Nickel or Gold Gold Female: Beryllium copper Insulator Teflon N/A Crimp ferrule Annealed copper Nickel or Gold
Materials Connector part Material Finish Bodies Brass Nickel or Gold Center Contact Male: Brass Gold Female: Beryllium copper Insulator Teflon N/A Crimp ferrule Annealed copper Nickel or Gold Electrical
Distributed by: www.jameco.com 1-800-831-4242 The content and copyrights of the attached material are the property of its owner. Connectors Features Snap-on interface facilitates assembly Conforms to CECC
SMB Connectors Specifications Flexible Cable Bulkhead PCB Mount... 66
Section Index Connectors Specifications... 62 Flexible Cable... 64 Bulkhead... 65 PCB Mount... 66 Other Information Assembly Instructions... 176 Cable Assembly... 166 Cable Information... 168 Numerical
Interface Mating Dimensions
SMPM Coaxial Connectors SMPM Connectors DC - 65 GHz SV Microwave offers a complete line of SMPM connectors. SMPM connectors, a push-on mating design, provide microwave performance through 65 GHz and offer
Interface Mating Dimensions
SMP Coaxial Connectors SMP Coaxial Connectors SMP Connectors Interface SMPM Cable Connectors SV Microwave offers a complete line of SMP connectors that conform to DSCC 94007, 94008 and MIL-STD-348. The
MCX Connectors Specifications Flexible Cable Semi-Rigid Cable Panel Mount PCB Mount... 22
Section Index Connectors Specifications... 17 Flexible Cable... 19 Semi-Rigid Cable... 20 Panel Mount... 21 PCB Mount... 22 Other Information Assembly Instructions... 176 Cable Assembly... 166 Cable Information...
Type N connectors DIVIDER PAGE
Type N connectors DIVIDER PAGE 179 N interface dimensions E D REF. PLANE REF. PLANE C D ØF ØB ØA ØA ØB ØE SEALING GASKET.625-24UNEF-2B G C H MIN. FULL H J F G MIN. FULL "N", MALE, Mil-Std-348A Fig. 304.1.140.110
... A Vital Part of Connection World CMPTER. Cable Connectors PCB Connectors Assembly Instructions Mounting Holes MCX CONNECTORS
... A Vital Part of Connection World Cable Connectors PCB Connectors s Mounting Holes MCX CONNECTORS COPYRIGHT ELECTRONICS 0 MCX Series Coaxial Connectors DESCRIPTION MCX connector are developed in Europe
SMB LOCK Introduction Characteristics Straight plugs Right angle plugs SMB limited detent (SMB-A) Receptacles...
CONTENTS PAGE SMB Introduction... 4 General... 5 Finder guide... 6 Interface... 7 Characteristics...8-9 Straight plugs...0- Right angle plugs...- Jacks... 3 Bulkhead jacks...4-5 Receptacles...6-7 PCB receptacles...
MicroMate (MMCX) Amphenol Specifications
Specifications ELECTRICAL CECC22000 Test Requirement Impedance 50 Ohm Frequency Range DC thru 6 GHz VSWR 4.4.1 SMT and Edgecard (Mated Pair) DC - 4 GHz 1.15 Max 4-6 GHz 1.40 Max Cabled Straight, Semi-Rigid
Our Most Important Connection is with You. SECTION 2 SMPM / SMP / SMP-LOCK / SMP-COM R201 / R222 / R222L / R2229
SECTION 2 SMPM / SMP / SMP-LOCK / SMP-COM R201 / R222 / R222L / R2229 Contents SMPM Introduction... 2-4 Interface... 2-5 Characteristics... 2-6 Plugs and Jacks... 2-7 Receptacles and panel shrouds... 2-8
mcx connectors DIVIDER PAGE
mcx connectors DIVIDER PAGE 207 mcx interface dimensions A REF. PLANE A REF. PLANE B B C C H D D ØF ØG ØG ØF ØE ØE,, Design in accordance with CECC 22220 male, plug INCHES / MILLIMETERS 3 MINIMUM MAXIMUM
2.92mm connectors DIVIDER PAGE
connectors DIVIDER PAGE 167 interface dimensions REF. PLANE F SEALING GASKET E NOTE 1 F REF. PLANE E G.312 HEX. ØD ØC ØB ØD ØC ØB ØA A.250-36 UNS-2B H.250-36 UNS-2A.170 FULL MALE, FEMALE, Mil-Std-348A
2.4mm connectors 155
connectors 155 interface dimensions REF. PLANE F SEALING GASKET E NOTE 1 F REF. PLANE E.312 HEX. ØA ØD ØB ØC ØD ØC ØB ØA M7 x 0.75-6g MALE, FEMALE, male, plug INCHES / MILLIMETERS 3 MINIMUM MAXIMUM LTR.
SMC SERIES Subminiature Coaxial Connectors
SERIES Subminiature Coaxial Connectors FEATURES Subminiature coaxial connectors with 50 Ω impedance for applications up to 0 GHz. (screw on mechanism)fulfills the subminiature coaxial connector requirement
Table of Contents SMA CONNECTORS
Table of Contents 45 SMA Connectors 3 MMCX Connectors 50 Ohm Connectors Specifications...46 Quick Connect...49 Semi-Rigid & Flexible Cable...50 PC Mount...56 Bulkhead & Panel Mount...62 Self-Fixture End
SERIES BMA, SUBMINIATURE BLIND MATE CONNECTORS
SERIES, SUBMINIATURE BLIND MATE CONNECTORS DESCRIPTION CONTENTS PAGE HUBER+SUHNER blind mate connectors open up special dimensions in microwave applications up to 18 GHz. HUBER+SUHNER offers a range of
onlinecomponents.com
Description Amphenol connectors are used in applications where maximum RF shielding and minimum noise radiation are required. Features/Benefits Available in 7/8-20 and 11/16-24 threading, C, BNC and TNC
Triax Amphenol. Description Amphenol Triax connectors are used in applications where maximum RF shielding and minimum noise radiation are required.
Description Amphenol connectors are used in applications where maximum RF shielding and minimum noise radiation are required. Features/Benefits Available in 7/8-20 and 11/16-24 threading, C, BNC and TNC
SMA CONTENTS PAGE 9-3
CONTENTS PAGE SMA Introduction... 4 General... 5 Finder guide...6-7 Interface... 8 Characteristics...9-10 Straight plugs...11-12 Right angle plugs...13-14 Straight jacks... 14 Straight flange jacks...14-15
SERIES MHV (H4) HIGH VOLTAGE CONNECTORS
SERIES MHV (H4) HIGH VOLTAGE CONNECTORS DESCRIPTION CONTENTS PAGE HUBER+SUHNER MHV connectors are coaxial miniature high voltage (MHV = Miniature High Voltage) connectors with 5 kv rms test voltage (mated
smpm connectors DIVIDER PAGE
connectors DIVIDER PAGE 95 interfaces socket (adapter).068 MIN..023 CONTACT ACCEPTS.012 +/-.001 PIN x.050 LONG.110.095 CENTER CONTACT FLUSH TO.008 RECESSION FEMALE, JACK pin (shroud) Mil-Std-348A Fig.
BLINDMATE CONNECTORS AND COMPONENTS. Selection Guide BMA BMMA BMZ BZ
BLINDMATE CONNECTORS AND COMPONENTS SV Microwave, Inc. is a world leader in the RF/microwave industry. We design and manufacture coaxial connectors, cable assemblies, attenuators, terminations, and custom
Amphenol RF Interconnects
1.6/5.6 Miniature 75 ohm coaxial connectors continued Right Angle Bulkhead Jack for PCB Plug to Plug Adapter Plug to Plug U Link Adapter 1566252M1N3GT3G75 1562071A1N3GT3G75 1562076A1N3GT3G75 1566252M01RFX
- (90 - f (GHz)) db (.05 SQT(f(GHz))) db
TNC Specifications to MIL-C-39012 The specifications below are general specifications for all TNC connectors. Specific Data for VSWR, Insertion Loss, R.F. leakage, etc., are available from the factory
TNC Series Series C TN 114
TNC Series TNC Series 114 TNC Interface Mating Dimensions (Per MIL-STD-348) TNC Interface Dimensions MALE Inches/Millimeters 3 Minimum Nominal Maximum LTR in. mm in. mm in. mm A.440 11.17 B.314 7.98.315
MCX SERIES. Description. Applications. Microminiature Coaxial Connectors
MCX SERIES Microminiature Coaxial Connectors Description Jy Chyun MCX Series connectors are ideal for applications and designs where weight and space savings are critical. This series has a 50 ohm impedance
SMPM. SMPM High Frequency Push-on. Module to Module (board to board) Misalignment. Application Notes SMPM
29 High Frequency Push-on Application Notes The connector, which is 30% smaller than its cousin, the, has similar features and applications. This is a multi-functional high frequency push-on connector
Cannon 50 Ohm RF Connectors. Electronic Components
Cannon 50 Ohm RF Connectors Electronic Components Over 90 year history... ITT Electronic Components is an innovative and dynamic company with the in-depth experience of a 90 plus year industry leader.
RF COAXIAL CONNECTORS, TYPE SMA, 50 OHMS (FEMALE CONTACT) ESCC Detail Specification No. 3402/002
Page 1 of 106 RF COAXIAL CONNECTORS, TYPE SMA, 50 OHMS (FEMALE CONTACT) ESCC Detail Specification Issue 5 June 2016 Document Custodian: European Space Agency see https://escies.org PAGE 2 LEGAL DISCLAIMER
RP SMA Female Connector Crimp/Solder Attachment For RG178, RG196
RP SMA Female Connector Crimp/Solder Attachment For RG178, RG196 TECHNICAL DATA SHEET PE4799 RP SMA Female Connector Crimp/Solder Attachment For RG178, RG196 Configuration Connector Connector Specification
PERFORMANCE SPECIFICATION SHEET ADAPTER, CONNECTOR, COAXIAL, RADIO FREQUENCY. (BETWEEN SERIES BNC TO SERIES TNC), CLASS 2, STRAIGHT PLUG
INCH-POUND MIL-PRF-55339/38A 10 January 2005 SUPERSEDING MIL-PRF-55339/38 11 January 1977 PERFORMANCE SPECIFICATION SHEET ADAPTER, CONNECTOR, COAXIAL, RADIO FREQUENCY. (BETWEEN SERIES BNC TO SERIES TNC),
RP SMA Male Connector Crimp/Solder Attachment for RG174, RG316, RG188, PE-B100, PE-C100, inch, LMR-100
RP SMA Male Connector Crimp/Solder Attachment for RG174, RG316, RG188, PE-B100, PE-C100, 0100 inch, LMR-100 RF Connectors Technical Data Sheet PE4771 Configuration SMA Male Reverse Polarity Connector MIL-STD-348
MMC RTX series EN3716
MMC RTX series EN3716 7 CONTENTS Page Introduction... 7-4 Application 7-4 Features... 7-4 Product overview... 7-5 Electrical characteristics... 7-6 Mechanical & environmental characteristics... 7-6 Products
FAKRA Jack Right Angle Connector Crimp/Solder Attachment for RG174, RG316, RG188,.100 inch, PE-B100, PE-C100, LMR-100, White Color
FAKRA Jack Right Angle Connector Crimp/Solder Attachment for RG174, RG316, RG188, 100 inch, PE-B100, PE-C100, LMR-100, White Color PE44648B Configuration FAKRA Jack Connector 50 Ohms Right Angle Body Geometry
Ultra Miniature Snap-on Coaxial Connector (PC Card Type 2 Mountable)
Ultra Miniature Snap-on Coaxial Connector (PC Card Type 2 Mountable) MMCX Series Right-angle Receptacle Features 1. Snap-on coupling mechanism makes it easy to engage and disengage. The rugged snap-on
SMA Male Connector Solder Attachment for RG188-DS, RG316-DS
SMA Male Connector Solder Attachment for RG188-DS, RG316-DS RF Connectors Technical Data Sheet PE4402 Configuration SMA Male Connector MIL-STD-348A 50 Ohms Straight Body Geometry Features Max Operating
RF COAXIAL CONNECTORS, TYPE SMA, 50 OHMS (MALE CONTACT) ESCC Detail Specification No. 3402/001
Page 1 of 68 RF COAXIAL CONNECTORS, TYPE SMA, 50 OHMS (MALE CONTACT) ESCC Detail Specification Issue 3 January 2014 Document Custodian: European Space Agency see https://escies.org PAGE 2 LEGAL DISCLAIMER
Broadcast. Use Solid Reliability. Return Loss Graph Lo-Pro. Environmental. Electrical. Contact. millohm
Tri-Loc Series Standardd & Lo-Pro Connectors Jacks and Plug ugs Lo-Pro Tri-Loc Connectors Full Crimp Procedure Broadcast Ideally Suited for Outdoor Use Solid Reliability Point-To-Point Solutions Specifications
Amphenol 348 Series High Density Connectors
348 Series High Density Connectors 12-093-6 348 Series I, II Table of Contents 348 Series Page No. High Density Connectors........................................................................ 1 Specifications.................................................................................
97 series crimp type plugs with solid shells
97 series crimp type plugs with solid shells 97-4106A L Max. N Ref. Q Max. V Fitting Threads Inch mm Inch mm Inch mm 10SL 1-3/8 34.93 3/4 19.057/8 22.23 5/8-24 12S 1-7/16 36.50 25/32 19.84 1 25.40 5/8-24
ArcTite. single path to optimal performance. Ultra-low profile bends
ArcTite brochure_8-pages_011918_r3.qxp_layout 1 1/20/18 12:13 PM Page 1 www.dynawave.com single path to optimal performance ArcTite assemblies maintain electrical performance even after bending...ensuring
EN3716 SAE AS81659 ARINC
6 DSX RTX Series series SAE AS81659 EN3716 ARINC 404 Page Introduction... 6-4 Applications... 6-5 DSX SAE AS81659 Product overview... 6-6 Technical characteristics :... 6-7 & 6-8 Electrical... 6-7 Mechanical
AMPLIMITE.050 Series Cable Assemblies, Series III
Cable Assemblies, Series III To meet Standard Applications the following 106 ohm, black jacketed cable assemblies are available. For AMPLIMITE Series cable assemblies that meet other impedance requirements
800 Pin Receiver and ITA Modules and Contacts 2
TABLE OF CONTENTS 800 Pin Signal Module 800 Pin Receiver and ITA Modules and Contacts 2 Interface Devices (IDs) CASS Receiver 4 Light Weight CASS Receiver 5 80 Series Receiver 6 CASS Connector Module Configuration
Shell material Insulator Contacts Sealing Temperature Mating Protection
Technical Data Shell material Machined components: die cast components: Shell plating: Cable entry: Copper-Zinc alloy (CuZn) Zinc (GD-Zn) Nickel (Ni) plated max. 10 mm Insulator Connector inserts: Polyamid
APPLICATION INFORMATION APPLICATION INFORMATION
RECOMMENDED BULKHEAD PANEL CUT-OUTS SCSI Fine Pitch Vertical PCB Mount NUMBER OF PANEL CUT-OUT DIMENSION TABLE POSITIONS B G H 26 31.2 (1.230) 29.8 (1.175) 27.6 (1.085) 40 40.1 (1.580) 38.7 (1.525) 36.5
1Rack and Panel Connectors
Rack and Panel Connectors Table of Contents RINC 600 Connectors Introduction............................................................2 Ordering Information.....................................................3
Apr11 Rev A
Product Specification SMA In-Series Adapters 04Apr11 Rev A 1. SCOPE 1.1. Content This specification covers performance, tests and quality requirements for the TE Connectivity (TE) SMA In-Series Adapters.
BNC SERIES Miniature Coaxial Connectors
Miniature Coaxial Connectors Description favorite in the adaptation of a wide range of aerial rods, Jy Chyun s NC connectors feature an allencompassing antenna mount, backed by exceptional electrical characteristics,
R Z18 Series : SMB CARLOCK
.. pn ao TECHNICAL DATA SHEET 1 / 7 EDGE CARD PIN IN PASTE VERSION All dimensions are in mm. COMPONENTS MATERIALS PLATING (µm) BODY CENTER CONTACT OUTER CONTACT INSULATOR GASKET OTHERS PARTS ZINC ALLOY
17 TW SERIES. Hybrid Connector SPECIFICATIONS: MATERIALS AND PLATINGS ELECTRICAL DATA CLIMATIC DATA MECHANICAL DATA
17 TW SERIES Hybrid onnector mphenol s 17TW series hybrid -Subminiature connectors are available with power, coax, high voltage and signal contacts assembled in the same connector body. These connectors
ASSEMBLY, INSTALLATION, AND REMOVAL OF CONTACTS AND MODULES
ASSEMBLY, INSTALLATION, AND REMOVAL OF CONTACTS AND MODULES FOR MICRO COAXIAL CONTACTS AND MODULES TABLE OF CONTENTS SECTION 1 RECEIVER CONTACT ASSEMBLY INSTRUCTIONS SECTION 2 ITA CONTACT ASSEMBLY INSTRUCTIONS
D X X - XX - XX - X X
CONSTRUCTION MATERIAL FINISH Shell Alluminium Alloy Cadmium Olive Drab over Electroless Nickle Electroless Nickle Insert Engineering Plastic Natural O-ring Silicone Rubber Natural Contact Retainer Beryllium
FISCHER FREEDOM TM SERIES
K CHAPTER FISCHER TM SERIES EASY MATING EASY CLEANING EASY INTEGRATION KEY FEATURES No key code: 360 mating freedom & optimized cable management Membrane-sealed contacts (patent pending) Low profile IP68
RF Coaxial Connectors SMZ (Type 43)
SMZ (Type 43) Introduction The ITT Cannon range of SMZ connectors are extensively used in 75 communication systems and have become the recognised standard in telecommunications in many parts of the world.
CMC Hybrid Connectors Standard and Power Versions
CMC hybrid connectors and mating headers provide sealed, high-density, modular and cost-effective wire-to-board and wire-to-wire connection systems for heavy-duty powertrain and body-electronics applications
PART NUMBER BREAKDOWN CP A 70 1 W D H - 10
SERIES 70 EMI/RFI Shielding Backshell Non-Environmental Outer Shield Termination Series 70 Backshells provide EMI/RFI protection using ferrules to secure a cable s outer shield. They do not offer environmental
Ethernet 100 Mbps Quadrax
Ethernet 100 Mbps Quadrax Quadrax Contact Today s technology for Airbone and Military equipment is more and more complex, requiring the management of an increasing flow of information at greater speeds.
CMC Hybrid Connectors Standard and Power Versions
CMC hybrid connectors and mating headers provide sealed, high-density, modular and cost-effective wire-to-board and wire-to-wire connection systems for heavy-duty powertrain and body-electronics applications
PHONO JACKS * Please visit the product pages on our website for the most up-to-date product information 3501F 3501FP 3501FR 3514PC 3515PC
PHONO JACKS BULKHEAD PHONO JACKS 123 3501F 3501FP 3501FR 3514PC 3515PC 3517PC BPJR01 BPJF01 BPJJ01 3505F 3503 FEATURES AND BENEFITS Front or rear mount configurations Durable plated machined brass construction
MIL-DTL Series IV Connectors
DEPENDABLE Secure breech lock coupling 100% scoop-proof Pin-to-pin mating protection helps prevent failures RUGGED Mated connectors help withstand high-impact shock Rear accessory threads help provide
K CHAPTER FREEDOM TM SERIES EASY MATING EASY CLEANING EASY INTEGRATION FISCHER KEY FEATURES
K CHAPTER FISCHER TM SERIES EASY MATING EASY CLEANING EASY INTEGRATION KEY FEATURES No key code: 360 mating freedom & optimized cable management Membrane-sealed contacts (patent pending) Low profile IP68
MMBX / MCX series R223 / R113 / R213
4 MMBX / MCX series R223 / R113 / R213 CONTENT Pages MMBX Introduction... 4-4 to 4-6 Interface... 4-7 Characteristics... 4-8 Plugs... 4-9 Receptacles... 4-9 to 4-10 Adapters... 4-11 emo board... 4-12
Operating voltage up to 5 kvdc Operating current up to 4,5 A 2-6 High voltage contacts Quick and easy assembling Protection class IP68 acc.
Operating voltage up to 5 kvdc Operating current up to 4,5 A 2-6 High voltage contacts Quick and easy assembling Protection class IP68 acc. DIN EN 60529 General characteristics and technical data Series
BNC75 Receptacle Connector for Broadcast
BNC Receptacle Connector for Broadcast BNC Series for 12G-SDI Characteristic Impedance Ω Lock Type Bayonet OUTLINE BNC series for broadcasting equipment is a high performance Ω connector which is compliant
Wedge in Plugs Stock No
Amphenol Connectors Description Plugs Stock No. Receptacles Stock No. 2-way 38170 38171 3-way 38172 38173 4-way 38174 38175 6-way 38176 38177 8-way 38178 38179 12-way 38180 38181 Wedge in Plugs Stock No.
Our Most Important Connection is with You. SECTION 17. Tooling & Accessories R280 / R282
SECTION 17 Tooling & Accessories R280 / R282 Contents Joule effect soldering devices... 17-4 Stripping tools...17-4 and 17-7 Point gauges... 17-4 Soldering... 17-5 Installation tools...17-5 to 17-6 Cassettes...
Series 80 Mighty Mouse Technical Reference Complete Product Specification
Summary Performance Specifications Current Rating (Maximum): Size #23 Contact: 5 A., Size #20 contact: 7.5 A., Size #16 contact: 13 A., Size #12 contact: 23 A. Test Voltage (Dielectric Withstanding Voltage)
Amphenol SCE2/Terrapin Series
APPLICATIONS TECHNICAL SPECIFICATIONS Amphenol SCE2/Terrapin Series Radios Headsets MATERIALS AND FINISHES Shell Material Shell Plating Contact Material Contact Plating MINIATURE PUSH-PULL CONNECTOR FOR
Product Specification QSL RF Connectors
Product Specification QSL RF Connectors 108-2324 04Feb09 Rev A 1. SCOPE 1.1. Content This specification covers performance, tests and quality requirements for the Tyco Electronics QSL RF Connectors which
ASSEMBLY, INSTALLATION, AND REMOVAL OF CONTACTS AND MODULES
ASSEMBLY, INSTALLATION, AND REMOVAL OF CONTACTS AND MODULES FOR 20/26 GHz COAXIAL CONTACTS AND MODULES Table of Contents SECTION 1 RECEIVER CONTACT ASSEMBLY INSTRUCTIONS SECTION 2 ITA CONTACT ASSEMBLY
Varicon. Series " x.130" x.150" Grid Pattern FEATURES TECHNICAL SPECIFICATIONS
Series 8016.075" x.130" x.150" Grid Pattern FEATURES Available in five sizes: 20, 38, 56, 90 and 120 contacts Insertable / removable Varilok contacts Crimp, solder, solderless wrap, and taper tab terminations
Varicon. Series " x.130" x.150" Grid Pattern FEATURES TECHNICAL SPECIFICATIONS
Series 8016.075" x.130" x.150" Grid Pattern FEATURES Available in five sizes: 20, 38, 56, 90 and 120 contacts Insertable / removable Varilok contacts Crimp, solder, solderless wrap, and taper tab terminations
Insulator Connector inserts: Polyamide (PA66) UL 94 V0 All connectors with different shielding material for different jacket and shield diameters.
Technical Data Shell material Machined components: die cast components: Shell plating: Cable entry: Copper-Zinc alloy (CuZn) Zinc (GD-Zn) Nickel (Ni) plated max. 18 mm Insulator Connector inserts: Polyamide
Push-Pull connectors
Push-Pull connectors Introduction This catalog presents the push-pull connectors ranges for industrial applications. These products are particularly suitable for high reliability and high quality applications
305/315/355 SERIES CARD EDGE CONNECTOR.156" (3.96mm) Contact Spacing
305/315/355 SERIES CARD EDGE CONNECTOR.156" (3.96mm) Contact Spacing 305/315/355 SERIES ORDERING CODE Example Part Number 305-056 - 521-2 04 Series Total Number of Contacts Contact Code Insulator Style
BNC and MHV SHV-5 and SHV-10 SHV-20 and SHV-B
Coaxial is the description for electrical feedthroughs with parallel and concentric conductor paths, and with the inner most conductor path electrically isolated from the vacuum flange. Grounded Shield
DATA-CON-X : SEALED USB TYPE A & B CONNECTORS
FEATURES & BENEFITS Sealed to IP67 & IP68 NEMA 250 (6P) (when mated) Feed-thru termination on the panel for easy field installation Field installable design is easy to assemble Quick connect bayonet or
Multi-Flex Low Loss, Pre-Connectorized Cable Sets, DC~18 GHz, MF02-Series
MultiFlex Low Loss, PreConnectorized Cable Sets, DC~18, MF02Series for rugged military, defense and T&M applications upto 18 use reliable performance, dependable service MF02Series Preconnectorized Cable
Amphenol s 2M Micro38999 Connector Series The New Aerospace Standard
Tri-Start Threaded Coupling General Information Page Guide Order... C29 Weight... C30 Plugs... C31 In-Line... C32 Square Flange... C33 Jam Nut... C34 PCB Sq Flange... C35 PCBJam Nut... C36 PCB Double Flange.
HyperGrip - Push/Pull Plastic Circular Connectors
A B C D E F G H J K HG2 HG3 HG4 Ø1.014 [25.76] 1.220 [30.98] Ø0.866 [22.00] 0.272 [6.91] 1.637 [41.59] 3.265 [82.93] Ø0.502 [12.75] Ø0.656 [16.66] 2.700 [68.56] 3.724 [94.60] Ø1.172 [29.77] 1.137 [28.87]
D-Subminiature EMI/RFI Shielding Interconnection Systems
Amphenol Amphenol PCD Shenzhen D-Subminiature EMI/RFI Shielding Interconnection Systems www.amphenolpcd.com.cn Product profile RR-HR D-Sub connectors - stamped and formed contacts REAR RELEASE CRIMP CONNECTORS
nterconnect compatibility new SEALED CONNECTORS harsh environment dual seals for harsh environments ergonomic locking tab for easier mating
new harsh environment SEALED CONNECTORS nterconnect dual seals for harsh environments ergonomic locking tab for easier mating compatibility AT Series plug wedges ensure a proper seal placement and contact
Connection Systems. Bulls-Eye Subminiature Circular Connectors
Connection Systems Bulls-Eye Subminiature Circular Connectors Connection Systems Bulls-Eye Subminiature Circular Connectors Hit the target every time with our high density connectors that provide high
Assembly, Installation, and Removal of Contacts and modules
Assembly, Installation, and Removal of Contacts and modules FOR 20/26 GHz coaxial CONTACTS AND MODULES Table of Contents Section 1 Receiver Contact Assembly instructions Section 2 ITA Contact Assembly
LMR-195-LLPX. LMR -195-LLPX Flexible Low Loss Plenum Coax TIMES MICROWAVE SYSTEMS
LMR-195-LLPX LMR -195-LLPX Flexible Low Loss Plenum Coax Ideal for Indoor/Outdoor Plenum Feeder runs Drop in replacement for RG-142 UL/NEC/CSA rated CMP/FT6 (listed under UL file #E-170516) Any wireless
2M805 Tri-Start Threaded Coupling
2M805 Tri-Start Threaded Coupling General Information 2M Specs 2M801 2M803 2M804 2M805 Series Micro Miniature Connectors: s 2M805 Series of connectors offers the best EMI and Vibration performance among
PRODUCT SPECIFICATION
1.0mm Pitch ZIF FPC Page 1 Top Entry Side Entry 1.0mm Pitch ZIF FPC Page 2 1.0 SCOPE. This specification covers performance, tests and quality requirements for 1.0mm Pitch ZIF FPC Connector 2.0 APPLICABLE
341/391 SERIES CARD EDGE CONNECTOR.100" (2.54mm) Contact Spacing
341/391 SERIES CARD EDGE CONNECTOR.100" (2.54mm) Contact Spacing 341/391 SERIES ORDERING CODE Example Part Number 341-062 - 520-2 02 Series Total Number of Contacts Contact Code Contact Rows Mounting Options
COIN CELL PC BATTERY HOLDERS
COIN CELL PC BATTERY HOLDERS 20mm to 30mm Sizes 12mm to 16mm & 1/3 N Sizes SINGLE CELL HOLDER (3-VOLT) DUAL CELL HOLDER (6-VOLT) Single and Dual Printed Circuit Cell Holders for Lithium Coin Cells. Designed
Mini50 Unsealed Connector System 2.00mm Pitch
USCAR Mini50 approved interface delivers 50% space savings over traditional USCAR 0.64mm connectors, with smaller terminals to fit more lowcurrent electrical circuits in interior, unsealed, transportation-vehicle
Amphenol Australia. ATM Series PRODUCT SHORTFORM. Amphenol Australia Pty Ltd. ATM Series
EX-STOCK AUSTRALIA ATM Series PRODUCT SHORTFORM Amphenol Australia Pty Ltd ATM Series ATM Series connectors are a high-performance, cost-effective solution specifically designed for smaller AWG applications,
RF Coaxial Connectors
SSMB/SSMC Introduction This range of 50 ohm microminiature radio frequency connectors is suitable for both military and commercial equipment operating at frequencies up to 4 GHz (SSMB) and 12.4 GHz (SSMC).
- - Introduction. Specifications
14 SERIES Introduction Amphenol 14 series connectors are water resistant, polarised, five and six contact electrical connectors for use in low voltage audio frequency circuits and applications. They employ
MDM MDM MIL-DTL STYLE MIL-DTL STYLE. Applications. Features
MDM Applications Features MIL-DTL-83513 STYLE As the result of the miniaturization of today s sophisticated electronics where more and more electronics are being packed into smaller and lighter electronic
MIL-DTL Series III Connectors
RELIABLE Self-locking threaded coupling 100% scoop proof Contact retention system provides excellent contact retention under severe vibration EMI PROTECTED Grounding fingers for excellent EMI protection
PRODUCT SPECIFICATION
MICRO-FIT BMI FLOATING CONNECTOR SYSTEM 1.0 SCOPE This Product Specification covers the 3.00 mm (.118 inch) centerline (pitch) connector system terminated with 20 to 30 AWG wire using crimp technology
Features and Application
MIL-DTL-38999 Features and Application Series II Features and Application MIL-DTL-38999 Series II connectors feature a bayonet coupling mechanism with lower profile design and rear-removable crimp contact