800 Pin Receiver and ITA Modules and Contacts 2
|
|
- Arabella Berry
- 5 years ago
- Views:
Transcription
1 TABLE OF CONTENTS 800 Pin Signal Module 800 Pin Receiver and ITA Modules and Contacts 2 Interface Devices (IDs) CASS Receiver 4 Light Weight CASS Receiver 5 80 Series Receiver 6 CASS Connector Module Configuration 7 Receiver Accessories 9 Interface Devices (IDs) CASS Interface Device/80 Series Interface Device 10 Extended Interface Device 11 Deep Drawn Interface Device 12 CASS KITS 13 ID Covers and Enclosures 14 Connector Modules Signal Modules 18 Power Modules 19 Coaxial Modules 20 Blank Modules 21 Contacts and Patchcords High Density Signal Contacts 22 High Density Power Contacts 23 Mini Power Contacts 24 Mini Coaxial Contacts 25 Solder Sleeve Mini Coaxial Contacts 26 Tools 27 Product Cross Reference 28 Part Number Index 31 Virginia Panel Corporation 1
2 QuadraPaddle TM Connector Modules 800 Pin Signal Module Virginia Panel Corporation s new QuadraPaddle technology offers unmatched high-density performance for 80 Series platform digital I/O requirements. VPC was instrumental in development of the CASS interface standard, and continues to provide innovative CASS-compatible solutions as requirements evolve. Adhering to the philosophy of open-architecture, standards-based interconnectivity, modules and contacts are designed for ease of integration with COTS products for plug & play capability. QuadraPaddle technology offers:! High-density interconnectivity with 800 signal contacts! Twin-female contacts on.100" (2.54 mm) centers to promote rapid integration with COTS products! Plug & play configuration options with COTS cable assemblies or a range of VPC solutions! Accommodation for DIN, SCSI, VHDCI, and other connectors! Multiple contact-types for added versatility and applications September 2004 VBCAS0901 Rev2.P7.0
3 QuadraPaddle TM Connector Modules 800 Pin Signal Module The 800 pin receiver module assembly consists of an aluminum carrier with integrated strain relief plates housing 480 pin and 320 pin QuadraPaddle modules. Receiver modules are molded from LCP and ID modules are machined from G10. QuadraPaddle contacts are rated at 3 Amps continuous at 1250 VAC. Receiver modules come fully loaded with twin-female contacts that enable plug and play connectivity with commercially available connectors. ID modules can be populated with a variety of contact options from standard crimp/solder contacts to twinmale contacts to accept commercially available connectors for rapid integration to the UUT. ID patchcords are available in 24 and 26 AWG. Innovative cable plug assemblies enable rapid integration by providing a standard COTS connector termination on one end and a connector block on the other that plugs directly into the back of the receiver module. QuadraPaddle Connector Modules P/N DESCRIPTION Receiver Module, 80 Series, QuadraPaddle 800 Signal Positions, fully loaded with contacts ID Module, 80 Series, QuadraPaddle 800 Signal Positions. QuadraPaddle Signal Contacts and Patchcords P/N DESCRIPTION Receiver Signal Contact, QuadraPaddle Twin Female, Replacement Contact Only ID Signal Contact, Male, AWG crimp/solder ID Signal Contact, Male, AWG crimp/solder ID Signal Contact, Round Post Twin Male ID Patchcord, 36, 24 AWG, single-ended, stranded IDPatchcord, 36, 26 AWG, single-ended, solid QuadraPaddle ID Tools P/N DESCRIPTION Extraction Tool (ID), QuadraPaddle Crimp Tool (ID), QuadraPaddle Crimp Die/Locator (ID), QuadraPaddle QuadraPaddle Cable Assemblies P/N DESCRIPTION Cable Assembly, 68 Pin Female SCSI to 70 Pin QuadraPaddle Plug Assembly, Cable Assembly, 68 Pin Female SCSI to 70 Pin QuadraPaddle Plug Assembly, Cable Assembly, 68 Pin Female SCSI to 70 Pin QuadraPaddle Plug Assembly, Cable Assembly, 68 Pin Female SCSI to 70 Pin QuadraPaddle Plug Assembly, Cable Assembly, 160 Pin Female DIN to 160 Pin QuadraPaddle Plug Assembly, Cable Assembly, 160 Pin Female DIN to 160 Pin QuadraPaddle Plug Assembly, Cable Assembly, 160 Pin Female DIN to 160 Pin QuadraPaddle Plug Assembly, Cable Assembly, 160 Pin Female DIN to 160 Pin QuadraPaddle Plug Assembly, 72 Virginia Panel Corporation 3
4 CASS RECEIVER The CASS Receiver is a single tier engaging mechanism with 19 modular positions that accepts a single tier Interface Device (ID) and features: A telescoping handle designed to ensure a physical engagement force of 35 lbs. (max.) RFI Gasketing Integrated Microswitch Hangers on the Receiver allow the ID to be placed on the ATE while the engaging handle is in the closed position. After the handle is lowered 90 degrees to the open position, the ID moves slightly forward, positioning it for connector engagement. The Receiver weighs 21 pounds and has an integrated Microswitch that is activated by engaging the ITA. P/N NAVY P/N DESCRIPTION AS CASS Receiver Interface, Single Tier, accepts 19 Modules 4 September 2004 VBCAS0901 Rev2.P7.0
5 CASS LIGHTWEIGHT RECEIVER The 80 Series lightweight and RTCASS receivers are designed for use on portable test stations where weight is a major consideration. Weighing only 11 lbs, the receiver features a single tier engaging mechanism with 19 modular positions, and accepts a single tier Interface Device (ID). A microswitch is integrated into the receiver and activated by engaging the ID. The lightweight receiver includes RFI gasketing but does not have a telescoping handle as specified by the Navy s CASS guidelines. The RTCASS version has both RFI gasketing as well as a telescoping handle. P/N DESCRIPTION Series lightweight receiver, Single Tier, accepts 19 modules RTCASS lightweight receiver, Single Tier, accepts 19 modules EQ. A A SECTION A-A Virginia Panel Corporation 5
6 80 SERIES RECEIVER Designed for commercial applications, the 80 Series Receiver features a single tier engaging mechanism with 19 modular positions, and accepts a single tier Interface Device (ID). Hangers on the Receiver allow the ID to be placed on the ATE while the engaging handle is in the closed position. After the handle is lowered 90 degrees to the open position, the ID moves slightly forward, positioning it for connector engagement. An integrated Microswitch is activated by engaging the ITA. The commercial 80 Series Receiver does not include the telescoping handle, RFI gasketing or mounting hole configuration specified by the Navy s CASS guidelines. P/N DESCRIPTION Series Receiver Assembly, Single Tier, accepts 19 Modules 6 September 2004 VBCAS0901 Rev2.P7.0
7 CASS CONNECTOR MODULE CONFIGURATION RECEIVER The following depicts the standard configuration for the CASS Receiver System typically used on a CASS station. Blank modules are placed in unused slots on the Receiver. Part Number Navy P/N Quantity Description Position AS Power Module (RCVR), 76 Positions J1, J AS Coaxial Module (RCVR), 64 Positions J2, J6, J7, J8 for Discrete Wiring or Side PCB Mount AS Coaxial Module (RCVR), 64 Positions J11 thru J17 For Center PCB Mount AS Signal Module (RCVR), with 210 Signal J3 Contacts For Right Angle PCB Mount AS Signal Module (RCVR), 210 Positions J9, J10 For Discrete Wiring AS Blank Module (RCVR or ID) J4,J18, J19 Virginia Panel Corporation 7
8 CASS CONNECTOR MODULE CONFIGURATION - CONT. ID The following depicts the standard configuration for the CASS Interface Device (ID) System typically used on a CASS station. Blank modules are placed in unused slots on the ID. Part Number Navy P/N Quantity Description Position AS Signal Module (ID), 210 Positions P3, P9, P10 For Discrete Wiring AS Power Module (ID), 76 Positions P1, P5 For Discrete Wiring AS Coaxial Module (ID), 64 Positions P2, P6, P7, P8 For Discrete Wiring AS Coaxial Module (ID), 64 Positions P11 thru P17 For Center PCB Mount AS Blank Module (RCVR or ID) P4, P18, P19 8 September 2004 VBCAS0901 Rev2.P7.0
9 RECEIVER ACCESSORIES VERTICAL HINGED MOUNTING FRAME The Vertical Hinged Mounting Frame bolts directly onto any 19" rack and accepts the CASS or 80 Series Receiver. When open, the frame hinges toward the operator providing access to system wiring. A support hinge is incorporated to support the receiver when the system is hinged open. Captive hardware is included to facilitate easy access to wiring. P/N DESCRIPTION Vertical Hinged Mounting Frame for the CASS Receiver (P/N ) Vertical Hinged Mounting Frame for the CASS Light-weight Receiver (P/N , ) Vertical Hinged Mounting Frame for the 80 Series Receiver (P/N ) P/N RECEIVER PROTECTIVE COVER Protective covers are available for the CASS or 80 Series receivers. When the receiver is not in use, the protective cover is engaged to protect the contacts and modules. The body of the protective cover is finished in gold chromate and exterior surfaces are painted black. P/N NAVY P/N DESCRIPTION AS Receiver Protective Cover for , , , or Virginia Panel Corporation 9
10 INTERFACE DEVICES (ID) ID Frames (also called Interchangeable Test Adapters or ITAs) are used in a number of applications to accomplish the required connection to the Unit Under Test (UUT). They can be wired to UUT Adapter Cables (through the enclosure), mounted to I/O connectors for functional testing applications, or they can be incorporated into mechanical and vacuum fixturing designs. CASS IDs are made of aluminum, nickel plated and include self locking threaded inserts used for connector module mounting. The 80 Series ID Frame is designed as a low cost alternative to the standard CASS ID for commercial applications. This ID is clear chromated and does not use threaded inserts for connector module mounting. P/N NAVY P/N DESCRIPTION ENCLOSURE AS CASS ID Frame, Single Tier, accepts 19 Modules /392/394/ Series ID Frame, Single Tier, accepts19 Modules /392/394/454 Contact Side Wiring Side P/N or September 2004 VBCAS0901 Rev2.P7.0
11 P1 P2 P3 P4 P5 P6 P7 P8 P9 P10 P11 P12 P13 P14 P15 P16 P17 P18 P19 P19 P18 P17 P16 P15 P14 P13 P12 P11 P10 P9 P8 P7 P6 P5 P4 P3 P2 P1 CASS/80 SERIES 80 SERIES ID FRAMES EXTENDED ID FRAME The Extended ID Frame allows end users to attach enclosures of their own design. Enclosure mounting holes are located on the sides of the ID instead of the front. The Extended ID is nickel plated. P/N DESCRIPTION Enclosures Extended ID Frame, P/N & Single Tier, Accepts 19 Modules EQ UNC-2B x.28 LG SLF LK HELICOIL INSERT 18 PLCS Wiring Side EQ EQ Contact Side UNF-2B x.29 LG SLF LK HELICOIL INSERT 12 PLCS.59 P/N Virginia Panel Corporation 11
12 P1 P2 P3 P4 P5 P6 P7 P8 P9 P10 P11 P12 P13 P14 P15 P19 P18 P17 P16 P15 P14 P13 P12 P11 P10 P9 P8 P7 P6 P5 P16 P17 P18 P19 P4 P3 P2 P1 CASS/80 SERIES 80 SERIES ID FRAMES DEEP DRAWN ID FRAME The Deep Drawn ID Frame is used with the Deep Drawn ID Enclosure. This ID Frame is available in two sizes, a 2.75" depth and a 5" depth. Both are nickel plated. P/N DESCRIPTION A B ENCLOSURE " Deep Drawn ID Frame, Single Tier, Accepts 2.75" 2.375" Modules & " Deep Drawn ID Frame, Single Tier, Accepts 5.00" 4.755" Modules & "B".99 7 EQ UNC-2B x.28 SELF LOCKING HELICOIL INSERT 16 PLCS Wiring Side "A" 18 EQ EQ Contact Side UNF-2B x.29 LG SELF LOCKING HELICOIL INSERT 8 PLCS P/N or September 2004 VBCAS0901 Rev2.P7.0
13 CASS KITS CASS ID FRAME Virginia Panel now offers an ID Kit to assist TPS Developers. The kit includes the CASS ID Frame, with a selection of Signal, Power and Coaxial Modules and Contacts, and Extraction Tools selected to meet the immediate needs of TPS development. The mini coax contacts feature Solder Sleeve for easy, reliable termination. ID KIT P/N Qty Part # Description Navy P/N ID Frame with 19 module positions 1899AS Signal ID Module with 210 positions for discrete wiring 1899AS Power ID Module with 76 positions for discrete wiring 1899AS Coaxial ID Module with 64 positions for discrete wiring 1899AS Coaxial ID Module with 64 positions for PCB mounting 1899AS ID Mini Coax Contact, Solder Sleeve, RG316 &178,& 50µ gold 2038AS ID Mini Power Contact, 20 Amp, 8 AWG, 50µ gold 1899AS ID Hi-Density Power Contact,10 Amp,14 AWG,50µ gold 1899AS ID Hi-Density Signal Contact,5 Amp,22 AWG, 50µ gold 1899AS Signal/Hi-Density Power Extraction Tool N/A Mini Power/Mini Coaxial Extraction Tool N/A CASS TOOLS The ID Tool Kit offers the necessary tools to terminate contacts crimp tools for the signal contacts and the heat gun and holding fixture for the solder sleeve contacts. CONTACT TOOL KIT P/N Qty Part # Description Signal Crimp Tool Signal Crimp Die Solder Kit for Solder Sleeve, includes holding fixture and adapter Steinel Heat Gun with nozzle, used for P/N Virginia Panel Corporation 13
14 ID COVERS AND ENCLOSURES ID PROTECTIVE COVER When storing IDs, the Protective Cover snaps onto the roller bearings of the ID to protect contact pins. Protective Covers are made of aluminum and black anodized. Keeper blocks are made of Delrin TM. P/N NAVY P/N DESCRIPTION AS ID Protective Cover ID HOUSING ASSEMBLY P/N The ID Housing Assembly mounts directly to the ID frame, providing a secure enclosure for cable and connections between instruments and the UUT. The Housing is made of aluminum. All surfaces are gold chromated and exterior surfaces are painted gray. The Housing Cover is finished in gold chromate and left unpainted. Hardware for mounting the Housing to the ID is included. P/N DESCRIPTION ID ID Cover and Housing & P/N September 2004 VBCAS0901 Rev2.P7.0
15 ID COVERS AND ENCLOSURES DEEP DRAWN ID ENCLOSURE The Deep Drawn ID Enclosure is a one piece, non-welded, enclosure (with cover plates) that mounts directly to the ID frame, providing a secure environment for cable and connections between instruments and the UUT. Housing and cover plates are made of aluminum and all surfaces are gold chromated. Hardware for mounting the Enclosure to the ID is included. The floating receptacle of the quarter turn fastener is installed by VPC; however, the stud and retainers must be installed to the cover plates after customer modifications and painting. The Deep Drawn Enclosure has been tested and passed MIL-STD-810C, MIL-STD-810D and MIL-STD-167-1, as shown in TABLE 1 on following page. P/N DESCRIPTION ID Deep Drawn ID Enclosure Kit, Unpainted, includes Housing, Cover Plates, Gasketing and Mounting Hardware (loose) & Handles on front panel Deep Drawn ID Enclosure Kit, Unpainted, includes Housing, Cover Plates, Gasketing and Mounting Hardware (loose) & Handles on front & top panels (Consult factory for cover plate and RFI gasket replacements) *Requires Crimp Tool for 1/4 turn captive hardware (P/N ). See page 24. P/N Virginia Panel Corporation 15
16 ID COVERS AND ENCLOSURES RECTANGULAR ENCLOSURE Designed to meet the general requirements for WRA and SRA testing, the Rectangular Enclosure has been tested and passed MIL-STD-810C, MIL-STD-810D and MIL-STD as shown in TABLE 1. The Rectangular Enclosure features five access panels with quarter-turn fasteners, RFI gasketing on all openings, and an 11.75" depth. The floating receptacle of the quarter turn fastener is installed by VPC; however, the stud and retainers must be installed to the cover plates after customer modifications and painting. The cover plates are predrilled for the quarter turn studs. Housing and cover plates are made of aluminum and all surfaces are gold chromated. Hardware for mounting the Enclosure to the ID is included. P/N DESCRIPTION ID Rectangular Enclosure (Consult factory for cover plate and RFI gasket replacements) & TABLE 1: Test Specifications High Temperature MIL-STD-810C, Method 501.1, Procedure 1 Low Temperature MIL-STD-810C, Method 502.2, Procedure 1 Thermal Shock MIL-STD-810C, Method 503.1, Procedure 1 Bench Handling MIL-STD-810C, accroding to Table 4 (Method 516.2, Procedure V) Relative Humidity MIL-STD-810D, Method 507.2, Procedure1, Cycle 1 Vibration MIL-STD *Requires Crimp Tool for 1/4 turn captive hardware (P/N ). See page 25. P/N September 2004 VBCAS0901 Rev2.P7.0
17 ID COVERS AND ENCLOSURES L-SHAPED ENCLOSURE Developed for applications that call for internal PCBs or external edge card adapters, the L-Shaped Enclosure has been tested and passed MIL-STD-810C, MIL-STD-810D and MIL-STD as shown in TABLE 1. The L-Shaped Enclosure features four access panels with quarter-turn fasteners, RFI gasketing on all openings, an 18.54" depth and 13.14" height, and a removable hinged cover. The floating receptacle of the quarter turn fastener is installed by VPC; however, the stud and retainers must be installed to the cover plates after customer modifications and painting. The cover plates are pre-drilled for the quarter turn studs. Housing and cover plates are made of aluminum and all surfaces are gold chromated. Hardware for mounting the Enclosure to the ID is included. P/N DESCRIPTION X ID L-Shaped Enclosure 8" & L-Shaped Enclosure 4" (Consult factory for cover plate and RFI gasket replacements) & *Requires Crimp Tool for 1/4 turn captive hardware (P/N ). See page 25. P/N /394 TABLE 1: Test Specifications High Temperature MIL-STD-810C, Method 501.1, Procedure 1 Low Temperature MIL-STD-810C, Method 502.2, Procedure 1 Thermal Shock MIL-STD-810C, Method 503.1, Procedure 1 Bench Handling MIL-STD-810C, accroding to Table 4 (Method 516.2, Procedure V) Relative Humidity MIL-STD-810D, Method 507.2, Procedure1, Cycle 1 Vibration MIL-STD Virginia Panel Corporation 17
18 A B C CASS/80 SERIES CONNECTOR MODULES Modules are available in various configurations to meet specific testing needs. Mounting hardware is included. Contacts are not included except where noted. SIGNAL MODULES Signal Modules are molded from an engineered resin that will withstand temperatures up to 220 C. The front of the modules are silkscreened with white nomenclature. DETAIL "A" UNC-2B x.09 DP. TYP. 4 PLCS. P/N (With Contacts) & P/N (No Contacts) P/N P/N NAVY P/N DESCRIPTION AS Receiver Module with 210 Signal Contacts for Right Angle PCB Mounting AS Receiver Module, 210 Signal Positions for Discrete Wiring. DETAIL "A" AS ID Module, 210 Signal Positions for Discrete Wiring 18 September 2004 VBCAS0901 Rev2.P7.0
19 CONNECTOR MODULES POWER MODULES Power Modules are molded from an engineered resin that will withstand temperatures up to 220 C. The front of the modules are silkscreened with white nomenclature. P/N NAVY P/N DESCRIPTION AS Receiver Module, 76 Power Positions for Discrete Wiring, 40, 50 AMP and 36, 10 AMP Hi-Density for 14 AWG, with alignment cap AS ID Module, 76 Power Positions for Discrete Wiring, 40, 50 AMP and 36, 10 AMP Hi-Density for 14 AWG. P/N P/N Virginia Panel Corporation 19
20 CONNECTOR MODULES COAXIAL MODULES Coaxial Modules are molded from an engineered resin that will withstand temperatures up to 220 C. The front of the modules are silkscreened with white nomenclature. P/N NAVY P/N DESCRIPTION AS Receiver Module, 64 Coaxial Positions for Discrete Wiring or for Side PCB Mount with alignment cap AS ID Module, 64 Coaxial Positions for Discrete Wiring P/N P/N September 2004 VBCAS0901 Rev2.P7.0
21 CONNECTOR MODULES COAXIAL AND BLANK MODULES Coaxial Modules are molded from an engineered resin that will withstand temperatures up to 220 C. The front of the modules are silkscreened with white nomenclature. Blank modules are made of aluminum and clear anodized. P/N P/N P/N NAVY P/N DESCRIPTION AS Receiver Module, 64 Coaxial Positions for Center PCB Mounting, with alignment cap AS ID Module, 64 Coaxial Positions for Center PCB Mounting AS ID and Receiver Blank Module P/N Virginia Panel Corporation 21
22 CONTACTS AND PATCHCORDS Contacts and Patchcords are available in various sizes and configurations. Contacts can be ordered separately and terminated by crimping, soldering and/or wire-wrapping. HIGH-DENSITY SIGNAL CONTACTS AND PATCHCORDS Signal contacts carry up to 5 amperes continuous and can carry pulsed current up to 15 amperes at a maximum duration of 800 milliseconds. Resistance ranges from OHMS. Superior performance is achieved by VPC s patented Tri-Paddle design. A variety of patchcords are offered using white, stranded wire unless otherwise noted. ID High-Density Signal Contacts Receiver High-Density Signal Contacts P/N /146 P/N /145 P/N /125 P/N P/N P/N VPC P/N Navy P/N Description AS ID 22 AWG Max, for crimp or solder, 30µ gold AS ID 22 AWG Max, for crimp or solder, 50µ gold * ID.025 square wire-wrap post, 30µ gold * ID.025 square wire-wrap post, 50µ gold ID AWG, Tri-Paddle, 30µ gold, crimp ID High-Density Signal Patchcords VPC P/N Navy P/N Description * RCVR 22 AWG Max, for crimp/solder, 30µ gold AS RCVR 22 AWG Max, for crimp or solder, 50µ gold * RCVR.025 square wire-wrap post, 30µ gold RCVR AWG, Tri-Paddle, 30µ gold, crimp Receiver High-Density Patchcords VPC P/N Uses Navy P/N Uses Contact P/N Description AWG AS ", crimped one end AS ", crimped one end AS ", crimped one end AS ", crimped one end 20 VPC P/N Uses Navy P/N Uses Contact P/N Description AWG * ", crimped one end AS ", crimped one end 24 VPC P/N Uses Navy P/N Uses Contact P/N Description AWG AS ", crimped both ends 22 VPC P/N Uses Navy P/N Uses Contact P/N Description AWG AS ", crimped both wires, one end 24 The Navy specifies 50µ of gold on all contacts VPC P/N Uses Navy P/N Uses Contact P/N Description AWG AS ", crimped daisy chain, 25 cont. 24 NOTE: Other patchcords available upon request. Please notify your VPC Sales Representative for more information. *Not a Navy Specification 22 September 2004 VBCAS0901 Rev2.P7.0
23 CONTACTS AND PATCHCORDS HIGH-DENSITY POWER CONTACTS AND PATCHCORDS High-Density Power contacts can carry up to 10 amperes maximum continuous current. A variety of patchcords are offered using white, stranded wire unless otherwise noted. ID High-Density Power Contacts Receiver High-Density Power Contacts VPC P/N Navy P/N Description AS AMP for 14 AWG crimp or solder, 30µ gold AS AMP for 14 AWG crimp or solder, 50µ gold VPC P/N Navy P/N Description AS AMP for 14 AWG crimp or solder, 50µ gold ID High-Density Power Patchcords Receiver High-Density Power Patchcords VPC P/N Uses Navy P/N Uses Contact P/N Description AWG AS ", crimped one end AS ", crimped one end AS ", crimped one end AS ", soldered one end AS ", soldered one end 18 VPC P/N Uses Navy P/N Uses Contact P/N Description AWG AS ", crimped one end AS ", crimped one end 14 VPC P/N Uses Navy P/N Uses Contact P/N Description AWG AS ", crimped one end 16 NOTE: Other patchcords available upon request. Please consult your VPC Sales Representative for more information. Virginia Panel Corporation 23
24 CONTACTS AND PATCHCORDS MINI POWER CONTACTS AND PATCHCORDS Mini Power contacts (solder terminations) can carry up to 50 amperes continuous current. A variety of patchcords are offered, using white, stranded wire unless otherwise noted. ID Mini Power Contacts Receiver Mini Power Contacts VPC P/N Navy P/N Description AS AMP for 8 AWG, 50µ gold VPC P/N Navy P/N Description AS AMP for 8 AWG, 50µ gold ID Mini Power Patchcords Receiver Mini Power Patchcords VPC P/N Uses Navy P/N Uses Contact P/N Description AWG AS ", soldered one end AS ", soldered one end AS ", soldered one end AS ", soldered one end 20 VPC P/N Uses Navy P/N Uses Contact P/N Description AWG AS ", soldered one end AS ", soldered one end AS ", soldered one end 8 VPC P/N Uses Navy P/N Uses Contact P/N Description AWG AS ", soldered both ends AS ", soldered both ends 16 VPC P/N Uses Navy P/N Uses Contact P/N Description AWG AS ", soldered both ends AS VPC P/N Uses Navy P/N Uses Contact P/N Description AWG AS ", soldered both wires one end 22 NOTE: Other patchcords available upon request. Please consult your VPC Sales Representative for more information. 24 September 2004 VBCAS0901 Rev2.P7.0
25 CONTACTS AND PATCHCORDS MINI COAXIAL CONTACTS AND PATCHCORDS Mini Coaxial contacts have a maximum VSWR of at 500 MHz. Transmission loss is to db at 500 MHz and to db at 2 GHz. Initial average resistance is.0035 OHMS; after 20,000 engagement cycles average resistance is less than.0085 OHMS. Dielectric breakdown voltage is greater than 1500 VDC. Center contacts are finished with 60µ gold; outer shields are finished with 30u gold except where noted. ID Mini Coax Contacts/50 OHM Receiver Mini Coax /50 OHM VPC P/N Navy P/N Description AS RG316, 30µ gold on shield AS RG316, 50µ gold on shield AS RG178, 30µ gold on shield AS RG178, 50µ gold on shield * Two.025 square wire-wrap posts, 30µ gold on shield * One.025 square wire-wrap post, 30µ gold on shield * One.025 square wire-wrap post, 50µ gold on shield AS Two.025 round posts.150 long, 50µ gold on shield * 24 AWG, 50µ gold VPC P/N Navy P/N Description AS RG316, 50µ gold on shield AS RG178, 50µ gold on shield * Two.025 square wire-wrap posts 30µ gold on shield ID Mini Coax Patchcords/50 OHM Receiver Mini Coax Patchcords/50 OHM VPC P/N Uses Navy P/N Uses Contact Description Wire AS ", crimped one end RG AS ", crimped one end RG AS ", crimped one end RG AS ", crimped one end RG316 VPC P/N Uses Navy P/N Uses Contact Description Wire AS ", crimped one end RG AS ", crimped one end RG178 VPC P/N Uses Navy P/N Uses Contact Description Wire AS ", crimped both ends RG AS ", crimped both ends RG AS ", crimped both ends RG178 NOTE: Other patchcords available upon request. Please consult your VPC Sales Representative for more information. *Not a Navy Specification Virginia Panel Corporation 25
26 CONTACTS AND PATCHCORDS SOLDER SLEEVE FOR COAXIAL TERMINATION Solder Sleeve TM termination is available for coaxial contacts. A durable, reliable and economical alternative to traditional crimping methods, Solder Sleeve is constructed of heat-shrinkable thermoplastic. The sleeve contains a fluxed solder pre-form, which provides the exact amount of solder and flux required to connect coaxial wire to the contact. The solder sleeve s one-piece, pre-assembled design makes application as easy as stripping the wire, inserting it and heating the contact. After shrinking, the sleeve acts as an insulator and provides strain relief for the solder joint. If contact replacement is needed, simply heat, pull the contact off the cable, clean the cable, insert a new contact, heat and plug contact back into module. To ensure proper connection, VPC offers a tool kit containing the holding fixture with the appropriate adapter and a separate heating gun (see page 25 for complete listing of tools). ID Mini Coax/Solder Sleeve Contacts/50 OHM Receiver Mini Coax/Solder Sleeve Contact/50 OHM VPC P/N Navy P/N Description AS RG316 & 178, 30µ gold on shield AS RG316 & 178, 50µ gold on shield VPC P/N Navy P/N Description AS RG316 & 178, 30µ gold on shield ID Mini Coax/Solder Sleeve Patchcords/50 OHM Receiver Mini Coax/Solder Sleeve Patchcords/50 OHM VPC P/N Uses Navy P/N Uses Contact Description Wire AS ", Solder Sleeve one end RG AS ", Solder Sleeve one end RG178 VPC P/N Uses Navy P/N Uses Contact P/N Description Wire AS ", Solder Sleeve one end RG AS ", Solder Sleeve one end RG178 FEATURES & BENEFITS Durable, Heat Shrinkable Thermoplastic that acts as an insulator and strain relief when heat is applied Reliable Connection - the sleeve contains a fluxed solder pre-form with the exact amount of solder and flux to terminate wire to the contact Economical - reduces termination time with its one-piece, pre-assembled design Ease of Termination - accomplished in just 3 easy steps Termination in 3 Easy Steps: 1. Strip the wire. 2. Insert the wire into the contact. 3.Heat the contact in the designated location 26 September 2004 VBCAS0901 Rev2.P7.0
27 CRIMP AND EXTRACTION TOOLS Virginia Panel provides a complete selection of crimp and extraction tools, as well as an assortment of inspection and quality control tools. Forming tools, weights and gages are used to ensure and maintain proper contact engaging pressure of the male and female Mini Coaxial Contacts. Mini Coax users who already own a Daniel s (or equivalent) crimp handle may now purchase the Hex Die with Locator separately. A cross reference is provided on pages to determine which tools are needed. CRIMP AND ASSEMBLY TOOLS P/N DESCRIPTION Signal Receiver and ID Crimp Tool for 14 AWG (for /129/147) Signal Receiver and ID Crimp Tool (for /108/125/146) Coaxial Receiver and ID Hex Crimp Tool (for /130/157/159, /141) Signal ID Crimp Die, Std. (for /146) Signal Receiver Crimp Die for 14 AWG (for ) Signal ID Crimp Die for 14 AWG (for /147) Coaxial Hex Crimp Die with Locator for use with Daniels HX4 Crimp Tool Handle Signal Receiver Crimp Die with wire stop, Std. (for /125) Coaxial ID Crimp Die for 24 AWG ( ) Crimp Tool for 1/4 turn Captive Hardware used on Deep Drawn Enclosure Cover Plates Solder Kit for Solder Sleeve Mini Coax Contact, includes Raychem holding fixture (AD-1319) and adapter (P/N ) Adapter for use with Raychem holding fixture (AD-1319) Steinel Heat Gun with nozzle for use with Solder Sleeve Mini Coax Contact (110V) ID Contact Tool Kit for Crimp and Solder (see page 8) Coaxial Crimp Tool for 24 AWG (for ) EXTRACTION TOOLS P/N DESCRIPTION Signal/High Density Power Contact Receiver and ID Extraction Tool Mini Power/Coaxial Receiver and ID Extraction Tool INSPECTION AND QUALITY CONTROL TOOLS P/N Navy P/N DESCRIPTION AS Center Conductor Forming Tool forms or closes center conductor (before assembly) on Female Receiver Mini Coax Contact AS Outer Shield Conductor Forming Tool forms or closes shield of male ID Mini Coax Contact * Weight Gage Kit for female Mini Coax Contact AS Outer Shield Conductor Expanding Tool opens shield of male ID Mini Coax Contact AS Center Conductor Enlargement Tool opens center contact of female Receiver Mini Coax Contact * Weight Gage Kit for male Mini Coax Contact * Inspection Gage to verify depth setting of center conductor on female Mini Coax Contact * Inspection Gage to verify depth setting of center conductor on male Mini Coax Contact *Not a Navy Specification Virginia Panel Corporation 27
28 PRODUCT CROSS REFERENCE RECEIVER Listed down the left side of the chart below are the CASS/80 Series Receiver Contacts and Patchcords. Across the top are the Receiver Modules and Tools, providing a quick visual guide to determine which Contacts go with which Modules and Tools. Receiver Modules Crimp Tools & Dies Extract Tools Miscellaneous Tools Receiver Contacts & Patchcords NOTE: Contact forming tools and weight gages optional, used to inspect contact or when contact has been damaged (Applies to Receiver and ITA contacts.) 28 September 2004 VBCAS0901 Rev2.P7.0
29 PRODUCT CROSS REFERENCE ID CONTACTS Listed down the left side of the chart below are the CASS/80 Series ID Contacts. Across the top are the ID Modules and Tools, providing a quick visual guide to determining which Contacts go with which Modules and Tools. ID Modules Crimp Tools & Dies Extract. Tools Miscellaneous Tools ID Contacts NOTE: Contact forming tools and weight gages optional, used to inspect contact or when contact has been damaged (Applies to Receiver and ITA contacts). Virginia Panel Corporation 29
30 PRODUCT CROSS REFERENCE ID CONTACTS Listed down the left side of the chart below are the CASS/80 Series ID Contacts. Across the top are the ID Modules and Tools, providing a quick visual guide to determining which Contacts go with which Modules and Tools. ID Modules Extract. Tools Miscellaneous Tools ID Patchcords September 2004 VBCAS0901 Rev2.P7.0
31 PART NUMBER INDEX VPC P/N Navy P/N Page Receiver AS * * * * * AS ID * AS * * * * * AS * * * * * 13 Receiver Modules AS AS AS AS AS * 3 Blank Module AS ID Modules AS AS AS AS * 3 ID Contacts AS * AS * AS AS * AS AS AS * AS * AS * AS AS * AS * * * 2 Receiver Contacts AS * AS AS * * AS AS * AS * 2 *Not a Navy Specification at time of printing VPC P/N Navy P/N Page ID Patchcords * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * 2 Receiver Patchcords * * * * * * * * * * * 22 Tools * * 2, * * * 13, * * * * * * * * * AS AS * AS AS * * * * * * * * 2 Virginia Panel Corporation 31
CASS Interface System Parts Section 1
Ver. 2.7 CASS USER S MANUAL Receiver CASS Interface System Parts Section 1 VPC P/N CASS P/N Description 310 115 101 1899AS265-01 CASS Receiver Interface, accepts 19 Modules Interface Device VPC P/N CASS
More informationVirginia Panel Corporation s 2100 Series/Gemini User s Manual. Installations, Operations and General User s Guide
Virginia Panel Corporation s 2100 Series/Gemini User s Manual Installations, Operations and General User s Guide Edition 2.1/April 2007 2100 SERIES/GEMINI USER S MANUAL VER. 2.1 OBJECTIVE The following
More informationWiring Assembly Instructions Section 5 P/N CASS P/N 1899AS RG316 P/N CASS P/N 1899AS RG316
Ver. 2.7 CASS USER S MANUAL VPC Tools Required For the assembly of the Mini-Coaxial Contact(s) VPC P/N 610 103 115/CASS P/N 1899AS284-01 and/or P/N 610 103 159/1899AS284-04 the following parts are required
More informationicon User s manual Table of Contents section 6 icon module installation and removal
icon User s manual Table of Contents SECTION 1 icon Part Identification SECTION 2 icon Receiver & ITA EnGAGEMENT & Disengagement SECTION 3 icon Receiver mounting SECTION 4 icon ITA cover removal and installation
More informationSMB LOCK Introduction Characteristics Straight plugs Right angle plugs SMB limited detent (SMB-A) Receptacles...
CONTENTS PAGE SMB Introduction... 4 General... 5 Finder guide... 6 Interface... 7 Characteristics...8-9 Straight plugs...0- Right angle plugs...- Jacks... 3 Bulkhead jacks...4-5 Receptacles...6-7 PCB receptacles...
More informationAssembly, Installation, and Removal of Contacts and modules
Assembly, Installation, and Removal of Contacts and modules FOR 20/26 GHz coaxial CONTACTS AND MODULES Table of Contents Section 1 Receiver Contact Assembly instructions Section 2 ITA Contact Assembly
More informationASSEMBLY, INSTALLATION, AND REMOVAL OF CONTACTS AND MODULES
ASSEMBLY, INSTALLATION, AND REMOVAL OF CONTACTS AND MODULES FOR 20/26 GHz COAXIAL CONTACTS AND MODULES Table of Contents SECTION 1 RECEIVER CONTACT ASSEMBLY INSTRUCTIONS SECTION 2 ITA CONTACT ASSEMBLY
More informationSMB Connectors Specifications Flexible Cable Bulkhead PCB Mount... 66
Section Index Connectors Specifications... 62 Flexible Cable... 64 Bulkhead... 65 PCB Mount... 66 Other Information Assembly Instructions... 176 Cable Assembly... 166 Cable Information... 168 Numerical
More informationSMB Amphenol. 50 ohm Coaxial Connectors Specifications 36 Plugs 37 Jacks 38 Bulkhead Receptacles PCB Receptacles 41-43
Description The name derives from SubMiniature B (the second subminiature design). The was developed in the 1960 s. is a smaller version of the SMA with snap-on coupling. Amphenol s connectors conform
More informationMMC RTX series EN3716
MMC RTX series EN3716 7 CONTENTS Page Introduction... 7-4 Application 7-4 Features... 7-4 Product overview... 7-5 Electrical characteristics... 7-6 Mechanical & environmental characteristics... 7-6 Products
More informationG 20x. G 14x G 20. G 40x. Pull-Thru, Scalable Solutions. Features and Benefits. The Standard for Pull-Through Systems since 2004
G 20 G 20x G 40x G 14x Pull-Thru, Scalable Solutions The Standard for Pull-Through Systems since 2004 VPC s pull-thru Mass InterConnect interfaces deliver reliable performance in an innovative platform.
More informationASSEMBLY, INSTALLATION, AND REMOVAL OF CONTACTS AND MODULES
ASSEMBLY, INSTALLATION, AND REMOVAL OF CONTACTS AND MODULES FOR MICRO COAXIAL CONTACTS AND MODULES TABLE OF CONTENTS SECTION 1 RECEIVER CONTACT ASSEMBLY INSTRUCTIONS SECTION 2 ITA CONTACT ASSEMBLY INSTRUCTIONS
More informationAMPLIMITE.050 Series Cable Assemblies, Series III
Cable Assemblies, Series III To meet Standard Applications the following 106 ohm, black jacketed cable assemblies are available. For AMPLIMITE Series cable assemblies that meet other impedance requirements
More informationEN3716 SAE AS81659 ARINC
6 DSX RTX Series series SAE AS81659 EN3716 ARINC 404 Page Introduction... 6-4 Applications... 6-5 DSX SAE AS81659 Product overview... 6-6 Technical characteristics :... 6-7 & 6-8 Electrical... 6-7 Mechanical
More informationMCX Connectors Specifications Flexible Cable Semi-Rigid Cable Panel Mount PCB Mount... 22
Section Index Connectors Specifications... 17 Flexible Cable... 19 Semi-Rigid Cable... 20 Panel Mount... 21 PCB Mount... 22 Other Information Assembly Instructions... 176 Cable Assembly... 166 Cable Information...
More informationDistributed by: www.jameco.com 1-800-831-4242 The content and copyrights of the attached material are the property of its owner. Connectors Features Snap-on interface facilitates assembly Conforms to CECC
More informationInterface Mating Dimensions
SMP Coaxial Connectors SMP Coaxial Connectors SMP Connectors Interface SMPM Cable Connectors SV Microwave offers a complete line of SMP connectors that conform to DSCC 94007, 94008 and MIL-STD-348. The
More informationSERIES BMA, SUBMINIATURE BLIND MATE CONNECTORS
SERIES, SUBMINIATURE BLIND MATE CONNECTORS DESCRIPTION CONTENTS PAGE HUBER+SUHNER blind mate connectors open up special dimensions in microwave applications up to 18 GHz. HUBER+SUHNER offers a range of
More informationMCX Amphenol. Description MCX. 50 Ohm Coaxial Connectors Specifications 18 Straight & Right Angle Crimp 19 Straight Solder & PCB 20-21
Description connectors conform to the European CECC 22220 Spec and was introduced in the 1980 s. While the uses identical inner contact and insulator dimensions as the SMB, the outer diameter of the plug
More informationOur Most Important Connection is with You. SECTION 2 SMPM / SMP / SMP-LOCK / SMP-COM R201 / R222 / R222L / R2229
SECTION 2 SMPM / SMP / SMP-LOCK / SMP-COM R201 / R222 / R222L / R2229 Contents SMPM Introduction... 2-4 Interface... 2-5 Characteristics... 2-6 Plugs and Jacks... 2-7 Receptacles and panel shrouds... 2-8
More informationBodies Brass Nickel or Gold Gold Female: Beryllium copper Insulator Teflon N/A Crimp ferrule Annealed copper Nickel or Gold
Materials Connector part Material Finish Bodies Brass Nickel or Gold Center Contact Male: Brass Gold Female: Beryllium copper Insulator Teflon N/A Crimp ferrule Annealed copper Nickel or Gold Electrical
More informationAMPLIMITE* HDP- 20 and Economy
AMPLIMITE* HDP- 20 and Economy Application Specification Crimp Snap Subminiature D 114-40030 Commercial s 05 MAY 11 Rev D NOTE i All numerical values are in metric units [with U.S. customary units in brackets].
More informationVaricon. Series " x.130" x.150" Grid Pattern FEATURES TECHNICAL SPECIFICATIONS
Series 8016.075" x.130" x.150" Grid Pattern FEATURES Available in five sizes: 20, 38, 56, 90 and 120 contacts Insertable / removable Varilok contacts Crimp, solder, solderless wrap, and taper tab terminations
More informationVaricon. Series " x.130" x.150" Grid Pattern FEATURES TECHNICAL SPECIFICATIONS
Series 8016.075" x.130" x.150" Grid Pattern FEATURES Available in five sizes: 20, 38, 56, 90 and 120 contacts Insertable / removable Varilok contacts Crimp, solder, solderless wrap, and taper tab terminations
More informationM Series Pin and Socket Connectors Catalog Revised 3-01
M Series Connectors Product Facts Most connectors intermateable with connectors made to MIL-C-28748 requirements Wide range of connector styles and sizes: standard c o n n e c t o r s (unloaded), posted
More informationNTC Thermistor Assemblies
FEATURES Standard and custom assemblies are available in a variety of configurations Assemblies can conveniently attach to or be an integral part of any system to monitor or control temperature No added
More informationTHREADED & BAYONET CONNECTORS FOR DEMANDING ENVIRONMENTS
MILITARY AND COMMERCIAL AVIATION MIL - DTL - 83723 SERIES III THREADED & BAYONET CONNECTORS FOR DEMANDING ENVIRONMENTS CONNECTORS FOR DEMANDING ENVIRONMENTS THREADED AND BAYONET MILITARY AND COMMERCIAL
More informationSMA CONTENTS PAGE 9-3
CONTENTS PAGE SMA Introduction... 4 General... 5 Finder guide...6-7 Interface... 8 Characteristics...9-10 Straight plugs...11-12 Right angle plugs...13-14 Straight jacks... 14 Straight flange jacks...14-15
More informationOur Most Important Connection is with You. SECTION 17. Tooling & Accessories R280 / R282
SECTION 17 Tooling & Accessories R280 / R282 Contents Joule effect soldering devices... 17-4 Stripping tools...17-4 and 17-7 Point gauges... 17-4 Soldering... 17-5 Installation tools...17-5 to 17-6 Cassettes...
More informationAmphenol. eries SJT. Series SJT. VG 96912, Series 1 PAN JN 1003
Amphenol eries SJT Series SJT VG 96912, Series 1 PAN 6433-2 JN 1003 Ordering information Ordering example: SJT G 06 RT 14-35 P A 014 Series (p. 9, 15, 18) SJT Scoop proof (100% scoop-proof) Junior (Miniature
More informationRP SMA Female Connector Crimp/Solder Attachment For RG178, RG196
RP SMA Female Connector Crimp/Solder Attachment For RG178, RG196 TECHNICAL DATA SHEET PE4799 RP SMA Female Connector Crimp/Solder Attachment For RG178, RG196 Configuration Connector Connector Specification
More informationabout us In 2011, Switchcraft was acquired by HEICO Corporation and became part of their Electronic Technologies Group.
table of contents 2 about us 3 custom products circular connectors & cable assemblies 6 en2 0.53 [13mm] od - 2-7 contacts 10 micro-con-x 0.53 [13mm] od - 2-7 contacts 16 en3 0.71 [18mm] od - 2-18 contacts
More informationFeatures and Application
MIL-DTL-38999 Features and Application Series II Features and Application MIL-DTL-38999 Series II connectors feature a bayonet coupling mechanism with lower profile design and rear-removable crimp contact
More information... A Vital Part of Connection World CMPTER. Cable Connectors PCB Connectors Assembly Instructions Mounting Holes MCX CONNECTORS
... A Vital Part of Connection World Cable Connectors PCB Connectors s Mounting Holes MCX CONNECTORS COPYRIGHT ELECTRONICS 0 MCX Series Coaxial Connectors DESCRIPTION MCX connector are developed in Europe
More informationVoice/Data/ Video Tools
Voice/Data/ Video Tools Professionals prefer Klein's high quality materials and construction for durable long-lasting tools. Klein VDV Tools provide time savings and reliability, especially in high-volume
More informationI Non-magnetic D-Sub Connectors
Non magnetic D-Sub Connectors Section I Non-magnetic D-Sub Connectors 5 Non magnetic D-Sub Contents Non magnetic D-Sub Connectors Cross reference table for ESA/SCC/SOURIAU/GSFC...7 Quality Assurance Testing...7
More informationRP SMA Male Connector Crimp/Solder Attachment for RG174, RG316, RG188, PE-B100, PE-C100, inch, LMR-100
RP SMA Male Connector Crimp/Solder Attachment for RG174, RG316, RG188, PE-B100, PE-C100, 0100 inch, LMR-100 RF Connectors Technical Data Sheet PE4771 Configuration SMA Male Reverse Polarity Connector MIL-STD-348
More informationTable of Contents SMA CONNECTORS
Table of Contents 45 SMA Connectors 3 MMCX Connectors 50 Ohm Connectors Specifications...46 Quick Connect...49 Semi-Rigid & Flexible Cable...50 PC Mount...56 Bulkhead & Panel Mount...62 Self-Fixture End
More informationType N connectors DIVIDER PAGE
Type N connectors DIVIDER PAGE 179 N interface dimensions E D REF. PLANE REF. PLANE C D ØF ØB ØA ØA ØB ØE SEALING GASKET.625-24UNEF-2B G C H MIN. FULL H J F G MIN. FULL "N", MALE, Mil-Std-348A Fig. 304.1.140.110
More informationQUALIFICATION TEST SUMMARY REPORT ESR Qualification Type Testing of Amphenol Corporation s 2M801 Series Connector
Page 1 of 13 QUALIFICATION TEST SUMMARY REPORT ESR-9389 Qualification Type Testing of Amphenol Corporation s Connector PREPARED BY: Patrick Cole Design Engineer AMPHENOL CORPORATION Aerospace Operation
More informationInterface Mating Dimensions
SMPM Coaxial Connectors SMPM Connectors DC - 65 GHz SV Microwave offers a complete line of SMPM connectors. SMPM connectors, a push-on mating design, provide microwave performance through 65 GHz and offer
More informationSMC SERIES Subminiature Coaxial Connectors
SERIES Subminiature Coaxial Connectors FEATURES Subminiature coaxial connectors with 50 Ω impedance for applications up to 0 GHz. (screw on mechanism)fulfills the subminiature coaxial connector requirement
More informationFAKRA-Comliant SMB 50-Ohm Inline Connectors 27 JUN 11 Rev E
Application Specification 114-13069 FAKRA-Comliant SMB 50-Ohm Inline Connectors 27 JUN 11 NOTE i All numerical values are in metric units [with U.S. customary units in brackets]. Dimensions are in millimeters
More informationFAKRA Jack Right Angle Connector Crimp/Solder Attachment for RG174, RG316, RG188,.100 inch, PE-B100, PE-C100, LMR-100, White Color
FAKRA Jack Right Angle Connector Crimp/Solder Attachment for RG174, RG316, RG188, 100 inch, PE-B100, PE-C100, LMR-100, White Color PE44648B Configuration FAKRA Jack Connector 50 Ohms Right Angle Body Geometry
More informationUltra Miniature Snap-on Coaxial Connector (PC Card Type 2 Mountable)
Ultra Miniature Snap-on Coaxial Connector (PC Card Type 2 Mountable) MMCX Series Right-angle Receptacle Features 1. Snap-on coupling mechanism makes it easy to engage and disengage. The rugged snap-on
More informationBLINDMATE CONNECTORS AND COMPONENTS. Selection Guide BMA BMMA BMZ BZ
BLINDMATE CONNECTORS AND COMPONENTS SV Microwave, Inc. is a world leader in the RF/microwave industry. We design and manufacture coaxial connectors, cable assemblies, attenuators, terminations, and custom
More information06. har-mik INTERFACE CONNECTORS
. INTERFACE CONNECTORS Miniature D connectors are a must in various cableto-board applications where space saving and high data transfer rates are required. For the purposes of miniaturization and speed,
More informationFuseholders PAGE. Fuseholders.
PAGE International Shock-Safe (Panel Mount).......................................................................... 467-468 Flip-Top Shock-Safe (Panel Mount)..................................................................................
More informationDT04 08P + W8P
Deutsch Connector Assortment Flip Kit *763354 This assortment contains 574 pieces/sets of widely used Deutsch Connectors. Flip Kits are handy both in the shop and the service vehicle. They are portable,
More informationEPIC. Connector Accessories CONNECTOR ACCESSORIES. Glands, Seal Rings & Adapters Glands 412 EPIC SM & SP Glands, EPIC CM-M Glands
CONNECTOR ACCESSORIES Glands, Seal Rings & Adapters Glands 412 EPIC SM & SP Glands, EPIC CM-M Glands D Series Pressure Screws 413 U Series Washers 413 Sealing Rings 413 Neoprene & Viton Concentric Sealing
More informationCONNECTORS & RECEPTACLES
60 HEX NUT Used in mounting rear or front of panel receptacles LOCK WASHER Prevents rear or front of panel receptacle from working loose when installed TYPICAL SL172F REAR MOUNT RECEPTACLE THREADED BUSHING
More informationHARTING. Interface Connectors. People Power Partnership
11 4 HARTING Interface Connectors People Power Partnership People Power Partnership Quality Connections Worldwide HARTING was founded in 1945 by the family that still owns the company. Today, HARTING employs
More informationAmphenol 348 Series High Density Connectors
348 Series High Density Connectors 12-093-6 348 Series I, II Table of Contents 348 Series Page No. High Density Connectors........................................................................ 1 Specifications.................................................................................
More informationTooling CONTENTS PAGE
CONTENTS PAGE Joule effect soldering devices... 3 Stripping tools...4-6 Pointer gauges... 7 Soldering & assembly tools...8-10 Installation tools...11-12 Tool kits for semi-rigid and flexible cables...13-22
More information1Rack and Panel Connectors
Rack and Panel Connectors Table of Contents RINC 600 Connectors Introduction............................................................2 Ordering Information.....................................................3
More informationabout us In 2011, Switchcraft was acquired by HEICO Corporation and became part of their Electronic Technologies Group.
table of contents 2 about us 3 custom products circular connectors & cable assemblies 6 en2 0.53 [13mm] od - 2-7 contacts 10 micro-con-x 0.53 [13mm] od - 2-7 contacts 16 en3 0.71 [18mm] od - 2-18 contacts
More informationI/O Card Interface Connectors
I/O Card Interface Connectors NX Series Features 1. Low Profile Protorusion above the PCB board is only 2.9mm, and the connectors can be mounted to type I and II I/O cards. 2. EMI/RFI protection Full metal
More informationMIL-PRF QPL Connectors MIL-PRF QPL Adapters Online Catalog Volume 1
MIL-PRF-39012 QPL onnectors MIL-PRF-55339 QPL dapters Online atalog Volume 1 Delta QPL connectors and adapters meet or exceed all requirements of MIL-PRF-39012 and MIL-PRF-55339. ecause these specifications
More informationConnectors Type M DIN / IEC Catalog E /01 Edition 1
Connectors Type M DIN 41612 / IEC 60603-2 www.erni.com www.erni.com Contents General Information 3 Electrical & Mechanical Specifications for Connectors 4 Standard Male Connectors for Daughtercards 6 Standard
More information2.92mm connectors DIVIDER PAGE
connectors DIVIDER PAGE 167 interface dimensions REF. PLANE F SEALING GASKET E NOTE 1 F REF. PLANE E G.312 HEX. ØD ØC ØB ØD ØC ØB ØA A.250-36 UNS-2B H.250-36 UNS-2A.170 FULL MALE, FEMALE, Mil-Std-348A
More information2.4mm connectors 155
connectors 155 interface dimensions REF. PLANE F SEALING GASKET E NOTE 1 F REF. PLANE E.312 HEX. ØA ØD ØB ØC ØD ØC ØB ØA M7 x 0.75-6g MALE, FEMALE, male, plug INCHES / MILLIMETERS 3 MINIMUM MAXIMUM LTR.
More information3M Assembly Equipment
M Assembly Equipment M TM Presses and Accessories All M TM Assembly Presses are designed to provide proper assembly on M TM Cable and Connectors. These presses, along with a locator plate, achieve accurate
More informationTE Connectivity DEUTSCH Single Module EN4165 connectors
Applications Cabin and avionic systems High-performance military aircraft Commercial airlines Communications equipment Missiles Military Railway TE Connectivity DEUTSCH Single Module EN4165 Connectors
More informationSMA Male Connector Solder Attachment for RG188-DS, RG316-DS
SMA Male Connector Solder Attachment for RG188-DS, RG316-DS RF Connectors Technical Data Sheet PE4402 Configuration SMA Male Connector MIL-STD-348A 50 Ohms Straight Body Geometry Features Max Operating
More informationSwitches. SERIES FEATURE ACTUATION MAX RATING SEAL RATING MOUNTING CIRCUITRY 115VAC, 28VDC)
SWITCH SELECTION GUIDE Toggle Switches SERIES FEATURE ACTUATION MAX RATING SEAL RATING MOUNTING CIRCUITRY (Resistive @ 115VAC, 28VDC) T1 2 or 3 Position, Momentary, 8A MIL-PRF-83731 15/32" or 1/4" dia.
More information8STA/8TA Series. Compact Circular Connectors Derived from MIL-DTL & JN1003. Connection Technologies
8STA/8TA Series Compact Circular Connectors Derived from MIL-DTL-38999 & JN1003 Connection Technologies 8STA/8TA Series Contents Overview Presentation... 06 Applications... 06 Features & benefits... 07
More informationDirectory chapter 01
Directory chapter 01 Miniature D connectors, 1.27 mm pitch Page I/O connectors................................................. 01.02 Pin and socket Technical characteristics........................................
More informationDistributed by: www.jameco.com 1-800-831-4242 The content and copyrights of the attached material are the property of its owner. M Series RoHS Ready M Series Connectors Product Facts Most connectors intermateable
More informationAmphenol-Tuchel Electronics 44 Series
44 Series Amphenol-Tuchel Electronics 44 Series Cost-effective environmental sealing Amphenol Tuchel 44 series connectors offer cost-effective performance for applications requiring environmental sealing.
More informationInstallation Instructions for LED Timing Light
Daytona Sensors LLC Engine Controls and Instrumentation Systems Installation Instructions for CAUTION: CAREFULLY READ INSTRUCTIONS BEFORE PROCEEDING OVERVIEW The P/N 120001 includes a versatile controller
More informationModular Bayonet connectors: a flexible solution for data and signals transmission in railways harsh environment.
GM Modular Bayonet connectors: a flexible solution for data and signals transmission in railways harsh environment. Passenger control Networking and lighting control Diagnostic support for brakes, motors
More informationTNC Series Series C TN 114
TNC Series TNC Series 114 TNC Interface Mating Dimensions (Per MIL-STD-348) TNC Interface Dimensions MALE Inches/Millimeters 3 Minimum Nominal Maximum LTR in. mm in. mm in. mm A.440 11.17 B.314 7.98.315
More informationConnection Systems. Bulls-Eye Subminiature Circular Connectors
Connection Systems Bulls-Eye Subminiature Circular Connectors Connection Systems Bulls-Eye Subminiature Circular Connectors Hit the target every time with our high density connectors that provide high
More information20. HONEYCOMB VENT PANEL
20. HONEYCOMB VENT PANEL FilterS. GENERAL INFORMATION Euro Technologies offers EMI Shielding Ventilation Panels. Available in a wide choice of materials, platings, and mounting configurations, it offers
More informationASSEMBLY, INSTALLATION, AND REMOVAL OF CONTACTS AND MODULES
ASSEMBLY, INSTALLATION, AND REMOVAL OF CONTACTS AND MODULES FOR MINI POWER CONTACTS AND MODULES TABLE OF CONTENTS SECTION 1 RECEIVER CONTACT ASSEMBLY INSTRUCTIONS SECTION 2 ITA CONTACT ASSEMBLY INSTRUCTIONS
More informationModular Bayonet connectors: a flexible solution for data and signals transmission in railways harsh environment.
GM Modular Bayonet connectors: a flexible solution for data and signals transmission in railways harsh environment. Passenger control Networking and lighting control Diagnostic support for brakes, motors
More informationDATA-CON-X : SEALED USB TYPE A & B CONNECTORS
FEATURES & BENEFITS Sealed to IP67 & IP68 NEMA 250 (6P) (when mated) Feed-thru termination on the panel for easy field installation Field installable design is easy to assemble Quick connect bayonet or
More informationGalley Connectors. Intermateable and Interchangeable Ability to mate with other ARINC 810 galley connectors in the market
Galley Connectors Intermateable and interchangeable with other ARINC 810 galley connectors, Amphenol Pcd s APeX Galley Connector, Rectangular is a reliable, robust, connector that uses overmold technology
More information35-kV Thru-Bushings F Series (bolt-in) for Air-Insulated to Air-Insulated Service 200 Amp, 600 Amp, 900 Amp and 1250 Amp
Page 1 2018 Equipment Connection Bus Bar, or Grounded Metal Equipment Plate F Series Mounting Holes ELRIM Cycloaliphatic Epoxy Provides: Nontracking, self-scouring, nonweathering performance Superior dielectric
More informationOver-moldable Ruggedized Connectors for higher Amperage
Over-moldable Ruggedized Connectors for higher Amperage Understanding Power and the need for interconnect solutions Power: Defined by the rate at which energy is used or generated. Electrical Power can
More informationDETAIL SPECIFICATION SHEET
INCH-POUND 30 June 2014 SUPERSEDING MIL-DTL-16377/53C 27 September 2005 DETAIL SPECIFICATION SHEET FIXTURES, LIGHTING; INCANDESCENT AND LIGHT EMITTING DIODE (LED), DETAIL LIGHTING, LANTERN, HAND, PORTABLE
More information2O3D3-19A REVB MOUNTING
Practice Section 1672 Issue 6, September 2014 MOUNTING ETL LISTED CONFORMS TO UL STD 60950-1 CONTENTS Multiple Patents Pending CLEI Code SOM2300C, CPR 204577 PAGE 1 INTRODUCTION... 2 1.1 Reason for Reissue...
More informationTermination Procedure for 723 Series SolderTacts Contacts for Coaxial Cable: D , D
enlo Park, CA 94025 USA Print 12-Jun-03 1 of 11 Termination Procedure for 723 Series SolderTacts Contacts for Coaxial Cable: D-602-44, D-602-45 1. Scope This engineering standard contains the termination
More informationMDM MDM MIL-DTL STYLE MIL-DTL STYLE. Applications. Features
MDM Applications Features MIL-DTL-83513 STYLE As the result of the miniaturization of today s sophisticated electronics where more and more electronics are being packed into smaller and lighter electronic
More information9316 series Underwater applications Explosion proof Hermetically sealed
Branche Connecteurs Offshore 9316 series Underwater applications Explosion proof Hermetically sealed Summary 9316 1 Introduction 2 Presentation 3 Technical characteristics 4 Synopsis 5 Part-numbering system
More information- (90 - f (GHz)) db (.05 SQT(f(GHz))) db
TNC Specifications to MIL-C-39012 The specifications below are general specifications for all TNC connectors. Specific Data for VSWR, Insertion Loss, R.F. leakage, etc., are available from the factory
More informationAmphenol RF Interconnects
1.6/5.6 Miniature 75 ohm coaxial connectors continued Right Angle Bulkhead Jack for PCB Plug to Plug Adapter Plug to Plug U Link Adapter 1566252M1N3GT3G75 1562071A1N3GT3G75 1562076A1N3GT3G75 1566252M01RFX
More informationSTRAIGHT BLADE PLUGS & CONNECTORS
STRAIGHT BLADE PLUGS & CONNECTORS Quick-thread assembly screws and cord-grip screws come backed-out, ready-to-wire. See-through, thermoplastic terminal chamber for clear view of terminals and wire connections.
More informationPERFORMANCE SPECIFICATION SHEET ADAPTER, CONNECTOR, COAXIAL, RADIO FREQUENCY. (BETWEEN SERIES BNC TO SERIES TNC), CLASS 2, STRAIGHT PLUG
INCH-POUND MIL-PRF-55339/38A 10 January 2005 SUPERSEDING MIL-PRF-55339/38 11 January 1977 PERFORMANCE SPECIFICATION SHEET ADAPTER, CONNECTOR, COAXIAL, RADIO FREQUENCY. (BETWEEN SERIES BNC TO SERIES TNC),
More informationWedge in Plugs Stock No
Amphenol Connectors Description Plugs Stock No. Receptacles Stock No. 2-way 38170 38171 3-way 38172 38173 4-way 38174 38175 6-way 38176 38177 8-way 38178 38179 12-way 38180 38181 Wedge in Plugs Stock No.
More informationSERIES MHV (H4) HIGH VOLTAGE CONNECTORS
SERIES MHV (H4) HIGH VOLTAGE CONNECTORS DESCRIPTION CONTENTS PAGE HUBER+SUHNER MHV connectors are coaxial miniature high voltage (MHV = Miniature High Voltage) connectors with 5 kv rms test voltage (mated
More informationEPIC CIRCON M23 Series
M23 Series EPIC EPIC CIRCON M23 Series Application Advantage Rugged nickel-plated, die-cast zinc body Positive vibration protection for use with motor drives and moving assemblies Integral EMC cable gland
More informationCam-Lok Single Pole Connectivity. The industry standard for reliable service under the most severe operating conditions.
Cam-Lok Single Pole Connectivity The industry standard for reliable service under the most severe operating conditions. Cam-Lok Single Pole Connectivity Cam-Lok connectors are the industry standard Cam-Lok
More informationINSTALLATION AND OPERATION MANUAL
INSTALLATION AND OPERATION MANUAL Document Number: 570-0049 Revision - 2-WIRE REMOTE SWITCH INTERFACE 455-0032 AND ELT INTERFACE 455-0041 INSTALLATION Artex Aircraft Supplies, Inc. 14405 Keil Road NE Aurora,
More informationPRODUCT SPECIFICATION
MultiCat TM In-line Power Connector System WIRE-TO-WIRE AND WIRE-TO-BOARD MALE CRIMP CONTACT (201845-00X0) FEMALE CRIMP CONTACT (201846-00X0) PLUG HOUSING (201840-00XX) RECEPTACLE HOUSING (201841-00XX)
More informationFeatures and Application
ML-DTL- Features and Application MS2426*/AE66* Features and Application ML-DTL- family offers connectors with bayonet coupling as well as threaded coupling. These connectors are intermateable with correspondingly
More information15 kv and 25 kv Thru-Bushings
Page 1 2001 ELRIM Cycloaliphatic Epoxy Provides: Nontracking, self-scouring, nonweathering performance Superior dielectric strength, dielectric loss and power factor Choice of shapes allows design innovation
More information25-kV Apparatus Bushings B Series (bolt-in) for Elbow to Air-Insulated Service 200 Amp, 600 Amp, 900 Amp and 1250 Amp
Page 1 2018 Grounded Metal Equipment Plate Equipment Connection Bus Bar or Other Component 15 kv or 25 kv Separable Insulated Connector (elbow) Equipment Connection Power Cable Power Cable ELRIM Cycloaliphatic
More informationRack & Panel. Miniature Rectangular / #16 Contacts /.062" Dia. / 13 Amps. MRA Series. Winchester/Retconn SPECIFICATIONS
MR Series Miniature Rectangular / #16 Contacts /.062" Dia. / 13 mps MR 34S-G MR 34P-G Hood The MR Series offers compact, lightweight and self-aligning plugs and receptacles with unusually high current
More informationPPT 802, Proximity Probe Transducer System
PPT 802, Proximity Probe Transducer System PPH 080 : Proximity Probe Head PEC 036 : Probe Extension Cable PRD 020 : Proximity Probe Driver Feature Non-contacting measurement system based on eddy current
More information