CITY OF DERBY Bid No REQUEST FOR BIDS

Transcription

1 CITY OF DERBY Bid No REQUEST FOR BIDS Sealed bid for One (1) wd Ford F550 Fire Squad will be received by the City of Derby, Kansas at City Hall, 611 Mulberry, Derby, Kansas until 2:00 pm on Thursday, December 18, Each bid must be submitted in a sealed envelope, addressed to the City Clerk of the City of Derby, Kansas. Each sealed envelope containing a bid must be plainly marked on the outside of the envelope as: Bid for Fire Squad Replacement. If forwarded by mail, the sealed envelope containing the bid must be enclosed in another envelope, addressed to the City Clerk, 611 Mulberry, Derby, Kansas The vehicle supplied shall meet the minimum specifications attached, and must be current production, new and unused. Bidder shall verify compliance with the attached specifications by so denoting next to each item. Complete printed literature, publications, and drawing of the unit proposed must be included with each bid. The City of Derby will not accept ownership until the vehicle has been inspected for compliance with specifications listed. Bids must be good for a period of 180 days. The City of Derby with or without cause may reject any or all bids. Each bidder shall specify the delivery date, which is days or less after receipt of the purchase order. Delivery shall be made to the Derby Fire Department, 1401 N. Rock Rd., Derby, Kansas after all pre-delivery services have been performed. New Fire Squad Bid Price: $ Trade-in Allowance for 08/2005 Fire Squad: $ Total Bid Price (FOB City of Derby, Kansas): $ Company: Bidders Name & Title: Date: Should you have any questions, please contact Deputy Chief Bill Pater, Derby Fire Department, Monday through Friday between 8:00 a.m. and 5:00 p.m. at (316) or billpater@derbyweb.com 1

2 City of Derby Fire Department Fire Squad Replacement Specifications Intent of Specification These specifications are designed for the purchase and delivery of a complete squad apparatus equipped as hereinafter specified. These specifications cover only general requirements as to the type of construction and test to which the apparatus shall conform, together with certain details of required finish, equipment and appliances. Minor details of construction and materials, not specified herein, are left to the discretion of the contractor, which shall be solely responsible for the design and construction of all features. Apparatus proposed by the bidder shall meet the applicable requirements of the edition of the National Fire Protection Association (NFPA) 1901, Standard for Automotive Fire Apparatus, current edition at time of contract execution. Loose equipment shall be provided only as stated in the following pages. Bidders shall also include in their bid a trade in price for one (1) 08/2005 Ford F x 4 Fire Squad with 300 gallon water tank w/foam cell, one (1) Briggs & Stratton gas powered fire pump, Foam Pro foam system, and booster reel. The 08/2005 Ford F-550 Fire Squad and all associated equipment is the property of The City of Derby. Pictures of this apparatus are included in this bid request package. Additional pictures and information will be provided upon request or the unit can be viewed at City of Derby Fire Station #82, 1401 N. Rock Rd. Derby, KS Bidders must have an established reputation in the field of fire apparatus construction and have been in such business for a minimum of ten (10) years. Further, bidder must have and maintain dedicated service facilities for the repair and service of products. Evidence of such facilities shall be included in the bid. Each bidder shall furnish satisfactory evidence of its ability to construct the apparatus specified, including the location of the factory where the apparatus is to be built. The bidder shall also demonstrate the bidder s capacity to render prompt service and to furnish replacement parts for the apparatus bid. Each bid shall include of complete "Manufacturer s Specifications" for the apparatus bid, including a detailed description of the apparatus and equipment bid, to which the apparatus furnished under contract shall conform. Any items or options that the manufacturer deems necessary, relevant or advantageous to this apparatus may be submitted with the bid and clearly identified as an option. All such items should be listed with the price of the proposed item on a separate page(s) under the header Additional Provisions. The City reserves the right to select none, any or all of the options identified. The manufacturer s specifications shall indicate size, type, model and make of all component parts and equipment. All exceptions to or deviations from the City s minimum specifications, qualifications, and performance requirements, as set forth herein, shall be clearly identified in the bid. 2

3 Exceptions shall be considered if they are, determined by the City, to be equal to or superior to these specifications, provided they are fully explained on a separate page entitled EXCEPTIONS TO SPECIFICATIONS. Exceptions to these specifications shall be clearly identified by reference to the heading title of specification to which exception is taken, and the page number thereof. Quality & Workmanship The design of the apparatus shall embody the latest approved automotive engineering practices. The workmanship shall be of the highest quality in its respective field. Special consideration shall be given to the following points: Accessibility of the various units which require periodic maintenance, ease of operation (including both pumping and driving) and symmetrical proportions. Construction shall be rugged and ample safety factors shall be provided to carry the loads specified. General Construction The apparatus shall be designed and the equipment mounted with due consideration to distribution of load between the front and rear axles so that all specified equipment, including filled water tank, a full complement of personnel and fire hose shall be carried without damage to the apparatus. Weight balance and distribution shall be in accordance with the recommendations of the National Fire Protection Association (NFPA) 1901 Standard for Automotive Fire Apparatus. Weight of apparatus shall meet all federal axle load laws. Performance Test A road test shall be conducted with the apparatus fully loaded and a continuous run of ten (10) miles or more shall be made under all driving conditions, during which time the apparatus shall show no loss of power or overheating. The transmission drive shaft or shafts, and rear axles shall run quietly and be free from abnormal vibration or noise throughout the operating range of the apparatus. Delivery & Training To insure proper break in of all components while still under warranty, Apparatus shall be delivered under its own power. Shipping by rail or truck shall not be acceptable. A qualified delivery engineer representing the contractor shall deliver the apparatus and remain for a sufficient length of time to instruct personnel in the proper operation, care and maintenance of the equipment delivered. Drawing of Approved Apparatus and Equipment After a contract has been awarded and a pre-construction conference held, the vendor shall furnish to the city, for review and signature, a general layout drawing depicting the apparatus body layout and appearance, and including any agreed upon changes from the vendor s bid. Such drawing shall consist of left side, right side and rear views, and shall be incorporated into the contract by reference. Cab & Chassis Warranty 3

4 Bumper to Bumper: 3 years/36,000 miles Power Train: 5 years/100,000 miles Corrosion Perforation: 5 years/unlimited mileage Diesel Engine: 5 years/100,000 miles Electrical System The body manufacturer shall warrant the new apparatus electrical system for a period of five (5) years or 50,000 miles (whichever occurs first) from the date of delivery to the original retail purchaser. The warranty will ensure that the vehicle will be free from defects in the electrical harness and connections under normal use and service within the warranty period. A copy of the warranty shall be supplied with the bid. Body & Structural Components The body manufacturer shall warrant the new apparatus body for structural integrity for a minimum of twelve (12) years from the date of delivery to the original retail purchaser. The warranty will ensure that the apparatus body will be free all structural defects of both material and workmanship that may appear under normal use and service within the warranty period. A copy of the warranty shall be supplied with the bid. Paint The body manufacturer shall warrant the apparatus body exterior paint finish against blistering, peeling, corrosion perforation, lack of adhesion or any other manufacturing or material defect for a period of five (5) years. A copy of the manufacturer's warranty shall be included with the bid. Inspection Trips The bidder shall provide two (2) factory inspection trips for four (4) city representatives, one (1) for pre-construction and one (1) for final inspection. The inspection trips shall be scheduled at times mutually agreed upon between the manufacturer's representative and the city. Travel costs, if greater than two hundred fifty (250) miles one way, shall be the responsibility of the bidder. Lodging and meals, while at the factory, shall be the responsibility of the bidder. Distances greater than two hundred fifty (250) miles one way, shall be by air travel from the Mid-continent Airport in Wichita, Kansas. Chassis or 2015 Ford F-550, 4 Door Cab, 4x4-6.7L Power Stroke V-8 Turbo Diesel -Dual combined 357-amp alternators (emergency vehicle package) -Dual batteries -Engine block heater -Transmission oil cooler -Electronic automatic transmission with overdrive -Electronic shift-on-the-fly four wheel drive with auto locking front hubs -Locking rear differential, 4.88 (no exception) -Stainless steel exhaust 4

5 Steering & Suspension -4 wheel disc brakes with front and rear vented discs -Firm ride suspension -Front anti-roll bar -HD front and Rear shocks -Rear leaf suspension -Rear anti-roll bar -HD rear leaf springs -Front and rear Stainless Steel Wheel Simulators, Phoenix brand or equivalent -LT225/70R19.5 BSW Michelin XDS2 All Position Radial, Appropriate Load Range, front and rear tires (no exceptions) -19,500 G.V.W. rating Safety -4-wheel anti-lock braking system -Dual airbags, passenger side front-impact cancelable airbag -Front height adjustable seatbelts -Back-up alarm when transmission is placed in reverse Interior Cab -Front Bucket Seats -Rear equipment storage box, constructed from aluminum and positioned in the driver s side rear cabin area. Storage box shall be designed and constructed to store a medical bag, oxygen bag, suction unit, and one (1) scba. Exact dimensions and location will be determined at pre-construct conference. -Troy Products Radio Console (or equivalent) with the following electronics and storage capability: - Motorola XTL 2500, 800 mhz mobile radio - Siren control box - Lighting control box - Map book storage area - Two (2) cup drink holder -Motorola 800 Mhz radio provided by City to be installed by apparatus manufacturer. -Rubber interior flooring in cab (no exceptions) -Air conditioning -AM/FM stereo -Clock -Fixed antenna -Minimum of two (2) 12V DC power outlets -Electric windows and door locks -Variable intermittent front windshield wipers -Interior dome lights, front & rear, bulbs to be red to reduce glare -Dual Front reading lights, bulbs to be red to reduce glare -12 Volt LED (Red) flexible dash mount map light 5

6 -Glove box -Tilt Wheel -Open door indicator light for apparatus compartment doors Analog instrumentation display includes: -Tachometer -Oil pressure gauge -Engine temperature gauge -Turbo/supercharger boost gauge -Transmission fluid temp gauge -Engine hour meter -Trip odometer -Warning indicators include oil pressure -Water temp warning -Battery -Key in ignition -Low fuel -Door ajar Exterior Features -Paint color: Fire Engine Red -Black side window moldings -Black front windshield molding -Black rear window molding -Black door handles -Complete tow package -Trailer harness -Brake controller -Driver and passenger manual black folding outside mirrors (extendable) -Halogen headlamps -Cab clearance lights -Clear coat monotone paint -Front and rear Stainless Steel Wheel Simulators, Phoenix brand or equivalent -Factory Full Cab Length Nerf Bars (Black) -Full front brush guard with winch mounting capability Winch WARN (or equivalent) #12,000 heavy duty winch with 12 Ft. remote control and roller fairlead. Winch accessory kit shall be provided. Water Tank -The water tank shall have a capacity of 300 gallons -The tank shall be constructed of 1/2" thick polypropylene -Exterior of tank shall have a satin finish and the color will be black -Fill tower with removable screen and cap. Minimum 4 opening to allow overhead filling 6

7 -Sump with anti swirl plate -Tank is to be baffled -3" vent with overflow pipe -1" N.P.T. tank fill fitting -Minimum 2 1/2" tank outlet fitting -Liquid level sight gauge Tank will be designed to keep the height at the lowest profile practical/possible. This requirement is to keep the weight of the unit as low as possible in the truck for stability reasons. Bidder will provide the exact dimensions of the tank they propose to supply with the bid submittal. Tank shall have a lifetime warranty. Pump The pump shall be a HPX100-KBD24 powered by a 24hp Kubota diesel engine or equivalent. Fuel connections shall be plumbed to the apparatus fuel tank for increased run time (No Exceptions). Pump to be centrifugal design, minimum capacities to be: PSI PSI PSI PSI Pump shall also have the following features: Suction inlet 1 1/2 female NPT Discharge 3" female NPT Impeller to be bronze Replaceable bronze clearance rings Self-adjusting, self-lubricating mechanical seal Electric start Pump and engine to be located at floor level of bed to completely eliminate pump priming problems when pumping from booster tank. Pump, engine, plumbing and all components shall be painted Red (or combination Red and Black) with high quality finish. Pump Panel Pump panel will be designed and located to provide safe, efficient, and easy operation of all valves and controls. Pump panel will be solid mounted and designed to provide easy access to operator 7

8 while standing at the rear of the apparatus. The following controls, at a minimum, will be located on the pump panel: Lighted pump-engine control panel pre-wired for connection to the vehicle battery Start/Stop switch for pump engine. Hand throttle control will be Vernier style (no exceptions). One (1) 3 inch minimum diameter, lighted pressure gauge, temperature rated to 30 degrees below zero, -30hg -400 psi. (Master) Valves/Controls for the following functions: 1) recirculating/refill valve; 2) booster hose; 3) forestry hoses(individual); 4) pre-connect hose. All will have proper identification labels attached and will be supplied with a 12 volt lighted pressure gauge, 3 inch minimum, with a range of psi. Booster reel rewind switch. Plumbing Heavy duty galvanized or brass piping and fittings shall be used throughout the system. All plumbing will be designed to prevent electrolysis. Brass drains shall be designed and placed to fully drain pump, pump valves and all associated pump plumbing due to possible extended periods of time when apparatus may be subjected to freezing temperatures. One (1) 2.5 inlet with a 2.5 brass, quarter turn full flow ball valve with cap and chain. Thread to be 2.5 NST female. Valve control will be at the valve and accessible from the rear of the truck (near but not on the pump panel). A check valve will be installed at the tank location to prevent back filling the tank from a fire hydrant. This action is intended to reduce the chances of damage to the internal plumbing inside the tank. One (1) 2.5 brass, tank to pump, quarter turn full flow ball valve. Valve control will be at the valve and accessible from the rear of the truck (but not on the pump panel). The tank to pump line shall be plumbed with 2.5" plumbing. A wire reinforced flexible connection shall be used to provide ease of service and to reduce vibration. One (1) 1 brass, quarter turn full flow ball valve and relief valve, with control at the pump panel, shall be provided for re-circulating water to prevent pump overheating. A 1.5 check valve will be installed at the tank connection to prevent water from draining out of the tank into the plumbing to reduce the chances of winter freeze-up. The 8

9 discharge hose from the valve going to the tank will be of 1 I.D. hose. One (1), 1.5 brass, quarter turn full flow ball valve with control at the pump panel, shall be provided for supplying the booster reel. The discharge hose from the valve going to the booster reel will be of 1.5 I.D. hose. Two (2), 1.5 brass, quarter turn full flow ball valves with controls at the pump panel, shall be provided for supplying two (2) 1 forestry hoses. Forestry hose connections shall be 1 NST male and accessible one (1) each side of the apparatus body from inside the pre-connect crosslay/forestry hose compartment. Exact discharge locations to be determined at pre-construct conference. The discharge hoses from the valves going to the forestry line connections will be a minimum of 1 I.D. hose. One (1), 1.5 brass, quarter turn full flow ball valve with control at the pump panel, shall be provided for supplying a pre-connected crosslay hose line. Supply line for preconnect shall include a Chickson swivel located inside the pre-connect crosslay/forestry lines compartment. Exact discharge location to be determined at pre-construct conference. The discharge hose from the valve going to the pre-connect Chickson swivel will be 1.5 I.D. hose. Note: All valves required/specified and supplied/installed will be full flow, quarter turn brass ball valves, swing-out design valve bodies and will be manufactured by Akron Brass (no exception). All valves are to be legibly identified for ease of operation. All suction and discharge connections including caps will be high quality and chrome plated with chains attached where applicable. Booster Reel Hannay, (no exception) electric rewind booster hose reel with two hundred feet capacity for 1 booster hose shall be mounted on top of booster tank. Frame to be silver with polished discs. Booster reel shall be positioned to unload hose to the rear of the apparatus One (1) spring nozzle clip shall be provided to secure 1 booster line nozzle. The booster reel shall be provided with a rewind switch located on the pump panel. The booster reel shall be provided with twin chrome hose roller and spool assemblies. Booster reel operation will be controlled by 1.5 valve at pump panel A 40 amp circuit breaker will be provided. 9

10 Apparatus Body The approximate 112"L x 96"W apparatus body shall be manufactured from minimum 1/8 aluminum sheets and aluminum extrusions. Apparatus body shall be protected by aluminum tread brite at appropriate areas that will be subjected to wear from hoselines, equipment, etc. Areas between compartments shall be covered with reflective red, to match apparatus cab color, to break up aluminum tread brite and provide a detailed finish look to the apparatus body. The apparatus body shall be undercoated. Compartments shall be equipped with a door switch, at the base of the compartment, which will activate the open door light in the cab when a compartment door is open. Compartments shall be of sweep-out design with no lip at bottom edge. Compartment interiors walls shall be painted a light gray spatter finish. The rear wheel well side panels shall be constructed of aluminum treadbrite with bright aluminum fenderettes. The driver s side and passenger s side rear wheel wells shall have an SCBA bottle storage compartment, forward of the rear wheel, with cast aluminum doors with seals. There shall be a driver s side recessed cast aluminum fuel fill access in the rear wheel well area behind the rear wheel. The rear of the body shall have two (2) large folding steps inside the pump compartment area for access to the hosebed and fill tower, exact location to be determined at preconstruction. Apparatus body shall have a full width tailboard step manufactured with aluminum tread brite. Driver s Side Front of Rear Wheel Compartment D1 One (1) compartment shall be provided ahead of the driver's side rear wheel. The compartment shall have approximate dimensions of 48" high x 33" wide x depth to back of compartment P1. D1 compartment shall have a roll up door with LED track lighting. Internal design of compartment shall provide removable organized storage shelving for a complete set of high pressure air bags. Design and dimensions shall match a current unit already in service. Driver s Side Above Rear Wheel Compartment 10

11 D2 One (1) compartment shall be provided above the driver's side rear wheel. The compartment shall have approximate dimensions of 27" high x 48" wide x 22" deep. D2 compartment shall have a roll up door with LED track lighting. Driver s Side Rear of Rear Wheel Compartment D3- One (1) compartment shall be provided behind the driver's side rear wheel. The compartment shall have approximate dimensions of 48" high x 27" wide x 22" deep. D3 compartment shall have a roll up door with LED track lighting. Passenger s Side Front of Rear Wheel Compartment P1 One (1) compartment shall be provided ahead of the passenger's side rear wheel. The compartment shall have approximate dimensions of 48" high x 33" wide x 22" deep. P1 Shall be equipped with an adjustable shelf fabricated to support two Hannay 100 ft. extrication reels. Shelf shall be rated to support minimum 250 lbs. P1 compartment shall be equipped with a slide out tray capable of supporting minimum 250 lbs. P1 compartment shall have a roll up door with LED track lighting. Passenger s Side Above Rear Wheel Compartment P2 One (1) compartment shall be provided above the passenger's side rear wheel. The compartment shall have approximate dimensions of 27" high x 48" wide x 22" deep. P2 compartment shall have a roll up door with LED track lighting. Passenger s Side Rear of Rear Wheel Compartment P3- One (1) compartment shall be provided behind the passenger's side rear wheel. The compartment shall have approximate dimensions of 48" high x 27" wide x 22" deep. P3 compartment shall have a roll up door with LED track lighting. SCBA Cylinder Storage Compartments One (1) each side, rear fender wells. Compartments shall be large enough to accommodate a single 4500 psi. SCBA cylinder. Doors shall be sealed to protect contents from the environment. Pike Pole Storage Compartment One (1) pike pole storage compartment approximately 10 high x 12 wide x full width of the apparatus body shall be provided crossways above compartment D1 & P1. Access shall be from either side of the apparatus body through pneumatically assisted hinged doors. Compartment doors shall be manufactured from aluminum tread brite, hinged at the top and pneumatically assisted. Compartment doors shall be sealed to protect contents from the elements. 11

12 Full length PVC tubes shall be provided, two (2) stacked on each side of the compartment for the following tools: Two (2) 6 New York Roof Hook Two (2) 6 Pike Pole Ladder Storage Compartment One (1) ladder storage compartment approximately 10 high x 22 deep x 76 long, shall be provided above drivers side compartment D2 & D3. Access shall be from the rear of the apparatus body through a pneumatically assisted hinged door. Compartment door shall be manufactured from aluminum tread brite, hinged at the top and pneumatically assisted. Compartment door shall be sealed to protect contents from the elements. Door shall be secured with dual flush mount quick release latches. Spineboard & Tool Storage Compartment One (1) spineboard & tool storage compartment approximately 10 high x 12 wide x 76 long, shall be provided above drivers side compartment P2 & P3. (Compartment must provide a minimum of 72 ½ of clear storage with access door in the closed position) Compartment will be constructed having an upper and lower level. Solid separation shall be provided the entire length of the compartment. Access shall be from the rear of the apparatus body through a pneumatically assisted hinged door. Compartment door shall be manufactured from aluminum tread brite, hinged at the top and pneumatically assisted. Compartment door shall be sealed to protect contents from the elements. Door shall be secured with dual flush mount quick release latches. Pre-connected Crosslay & Forestry Lines Compartment One (1) crosslay compartment approximately 10 high x 24 wide x full width of the apparatus body shall be constructed above compartment D1, D2, P1, and P2. Access shall be from either side of the apparatus body through aluminum tread brite hinged doors, as well as overhead through a hinged and pneumatically assisted compartment cover door. Overhead compartment door dimensions shall be approximately 72 x 24. Pre-connect hose bed compartment cover door shall be equipped with a stainless steel piano hinge to allow access for loading of pre-connect and forestry hoses. Door shall open towards front of apparatus. Door shall be secured with a Hansen (or equivalent) D-ring handle style latch. Tow Eyes 12

13 Located at the rear of the apparatus shall be two (2) chrome tow eyes. Located at the front of the apparatus shall be two (2) black tow eyes. Tow eyes shall be mounted to the chassis frame rail and capable of withstanding the necessary forces, that will be applied, to remove the fully loaded apparatus when stuck. Rear Receiver & Safety Chains Attachment Brackets A fitted recessed rear receiver hitch shall be mounted to the chassis frame. Rear receiver shall be rated at 5000# minimum. Rear receiver shall be equipped with safety chain attachment brackets. Shoreline One (1) shoreline receptacle shall be provided to operate the dedicated 120-volt circuits. The shoreline receptacle (s) shall be provided with a NEMA 5-20, 120 volt, 20 amp, straight blade Kussmaul (or equivalent) Super auto eject plug with a red weatherproof cover. 120 Volt Interior Receptacles & Powerstrips Receptacles shall be NEMA 5-20, 120 volt, 20 amp, three (3) wire duplex household type connected to the shoreline. There shall be two (2) duplex receptacles provided at the following locations: - One (1) upper front wall of compartment D2. - One (1) upper back wall of compartment P3. Two (2) interior 120 volt power strips with six (6) outlets per strip, shall be provided and mounted one (1) back side of front console and one (1) back wall of cab. Power strips shall be black in color and powered by shoreline. Location of all fuses and circuit breakers for apparatus body will be discussed at preconstruct conference. Emergency Warning System Whelen LFL Liberty SX Series Super-LED 54 inch light bar (or equivalent) shall be mounted on the cab. The light bar shall have red, blue and clear lights. Lightbar shall include OPTICOM traffic signal controlling system. Eight (8) Whelen model 700 series (or equivalent) LED flashing lights shall be provided with bezels. The LED lights shall be located two (2) red/blue at the front of the apparatus, two (2) red/blue at the rear of the apparatus and two (2 ) red/blue on each side of the apparatus located one (1) at the front, and one (1) at the rear. A Whelen model 295HFSA1 (or equivalent) full function 100 watt siren with appropriate speaker shall be mounted on the front of the chassis in a location to protect the speaker from damage during off-road operations. All emergency lights shall be controlled from a module located inside the cab, accessible to both the driver and front passenger. 13

14 Scene Lighting There shall be two (2) Fire Research Focus Evolution LED side mount telescopic lights provided, one (1) mounted each side on the front corner of the rescue body. Clearance shall be provided to allow 360 degree rotation without interfering with access to any compartment. The lamphead shall have eight (8) ultra-bright white LEDs. It shall operate at 12/24 volts DC, draw 13/6.5 amps, and generate 15,000 lumens. The lamphead shall direct 50 percent of the light onto the action area while providing 50 percent to illuminate the working area. The lamphead angle of elevation shall be adjustable at a pivot in the mounting arm and the position locked with a round knurled locking knob. The lamphead shall incorporate heatdissipating fins and be no more than 5 3/16" deep by 3 5/16" high by 11 1/2" wide. The lamphead and mounting arm shall be powder coated white. Each light shall be independently switched at the console. Switches shall be immediately accessible to the driver and front passenger. Work Lights There shall be six (6) Fire Research Spectra LED Flood and Loading Light model SPA900- Q65 surface mount lights provided, two (2) each side of the apparatus body and two (2) at the rear of the apparatus body. The lamphead housing shall be aluminum with a chrome colored bezel. NFPA Ground Lighting Package A ground lighting package shall be installed to provide lighting around the underside of the apparatus. All lighting shall be LED, rubber mounted, waterproof, and located so they are not damaged during off-road operations. Lights shall activate when transmission gear selector is placed in PARK. Lettering & Striping The apparatus shall be striped to meet NFPA standards. The cab shall be lettered with gold leaf style lettering, to resemble current Derby Fire squad unit. A four (4) inch white reflective stripe shall be provided along the side and rear of the apparatus. Incorporated into the stripe shall be DIAL 911 on D3 and P3 compartment roll up doors, to resemble current Derby Fire squad unit. Lettering and striping to be approved by Derby Fire at the pre-construct conference. 14