Albemarle County Virginia Brush Fire Truck Specification

Transcription

1 Albemarle County Virginia Brush Fire Truck Specification Purpose: This specification is intended to be used for the procurement of Brush Fire Suppression Apparatus for the Fire Departments & Companies in Albemarle County. This specification is not intended as a minimum. It is designed to provide a serviceable piece of equipment without any modifications by the requesting Department or Company. This specification is designed to allow each Department or Company to modify it s contents to meet their individual needs. The recommendation of this committee through this specification to allow modifications as mentioned above, but all of the requirements set forth in this specification should be considered a minimum when making modifications. Basic Requirements: Chassis to have dual rear wheels Chassis to have diesel engine Chassis to have automatic transmission Chassis to have all wheel drive Completed unit not to exceed 80% of gross vehicle rated weight Fire Suppression Unit to have Diesel Powered Auxiliary Fire Pump Fire Suppression Unit Water Tank to have 300 U.S. Gal Capacity Fire Suppression Unit to have a minimum 10 U.S. Gal Foam Supply tank. Fire Suppression Unit to have Foam Pro 1600 Foam System or equivalent Fire Suppression Unit to have Maximum Storage Compartments mounted for best use of space. Extended Front Bumper for mounting of remote controlled fire suppression nozzle on bumper

2 Competed Unit to have Class Three Receiver Hitch at front and Class Five Receiver Hitch rear of Unit. (This hitch to allow use of portable winch and trailer towing) 12 Volt outlet to be proved at both location for use of a portable winch. 7 Pin Trailer connector to be provided at the rear trailer hitch. Electric Brake controller to be provided by Chassis Manufacturer. Unit to have class three receiver mounted under body front of the rear wheels on both sides to allow use of winch pull from the side. Winch to be used on this unit is a Warn XD 9000 I Multi-mount System. Winch will be shown in bid document as an option/priced. Chassis: Ford 550 Super Duty Chassis Cab: 2 Door Supercab XLT with Rubber Floor Mats 6.0L Power Stroke Diesel TorqShift 5 Speed Automatic Transmission w/ PTO Provision 4 X 4 Transfer Case Manual 2 Speed 162 Wheelbase 60 Cab to Axle 17,950 Lb. Gross Vehicle Weight ( 80 % 14,320 lbs.) Power Windows & Doors Power Steering Power Brakes Heavy Duty Vinyl Bucket Seats Front Ford Paint Color to be specified by Agency Trailer Tow Mirrors 4 Wheel ABS Brakes 4 Wheel Disc Brakes (Largest Available) Driver & Passenger Air Bags (without disable switch) Tow Hooks Front & Rear Limited Slip 4:88-1 Axle Ratio Air Conditioning Auxiliary Idle Kit (Should be standard in ECM)(Manual Control) 40 U. S. Gal Fuel Tank aft Rear Axle with skid plate Seven pin trailer connector and factory installed electric brake controller.

3 Fire Suppression Unit: Flat Bed Style Body 96 in width not to exceed 98 (Maybe be steel or aluminum) Bed to be with front Cab Protection Gate (Front Gate to be no wider than the with of cab) (Floor of Bed to be Line-X Coated after drilling for mountings and before mounting of all additions) Bed to be approximately 120 in length Water Tank to be Poly material with life time warranty 300 U.S. Gal capacity. The tank will have a bucket fill hinged door located on top of the tank. The water tank will have a 4 overflow thru the floor of the tank and will be a part of the top fill assembly. A tank to pump line will be provided via a 3 NPT bushing. A tank refill line will be provided with a 1-1/2 Bushing. Tank will accommodate a Fire Research water level indicator. Foam Tank in addition to water tank 10 U.S. Gal minimum incorporated into the water tank (Must not reduce water capacity) Compartment 84 L X 32 H X 19 D on the passenger side of body. 2 Doors hinged on top with D Handle Latches. The walls and roof will be made of 1/8 brite dip aluminum diamonette. The floor will be level to allow it to swept out. Gas Piston on each side of door to assist raising. Rear wall will have 5/8 marine grade plywood installed. (sizes are approximate and should be as close as possible, use of standard commercial grade box acceptable) Compartment 108 L X 32 H X 19 D on the driver side of body. 2 Doors hinged on top with D Handle Latches. The walls and roof will be made of 1/8 brite dip aluminum diamonette. The floor will be level to allow it to be swept out. (sizes are approximate and should be as close as possible, use of standard commercial grade box acceptable) Compartment 24 L X 14 H X 18 D on the passenger side under the front of the body behind the cab and in front of the rear wheels. Door hinged on the body with D handle latch. (sizes are

4 approximate and should be as close as possible, use of standard commercial grade box preferred) Compartment 24 L X 14 H X 18 D on the driver side under the front of the body behind the cab and in front of the rear wheels. Door hinged on the body with D handle latch. (sizes are approximate and should be as close as possible, use of standard commercial grade box preferred) Hard Suction Hose Trays: Aluminum Trays will be fabricated and installed on top of the driver side of water tank to accommodate 3 10 sections of 3 hard suction Hose Storage: Hose Bed to be placed on top the passenger side compartment Double Jacket fire suppression hose preconnected to pump discharge. Hose bed to be placed on top of the driver side compartment to accommodate 200 or more of 3 double jacket fire suppression hose. Fire Pump: Provide a Waterous E 500 Series Diesel Pump ( Model 501 A or E 511 A) Company or department requesting brush truck will specify which pump. The pump will be equipped with an electric pump primer for use with environmentally safe oil. The Pump will wired to the truck electrical system and piped to the truck fuel tank. The pump will be mounted on the right rear corner of the truck bed crossways to allow for servicing Optional Fire Pump: and best use of space. (E501A PSI and PSI) (E511A PSI and PSI) Optional Fire Pump: (This pump was included to meet special needs of East Rivanna Vol. Fire Company) Provide a Hale 30FS pump driven by a Duetz BF3L HP@\2800 rpm diesel engine. The pump must provide approximately PSI and PSI. The pump will be equipped with an electric pump primer for use with environmentally safe oil. The Pump will wired to the truck

5 electrical system and piped to the truck fuel tank. The pump will be mounted on the right rear corner of the truck bed crossways to allow for servicing and best use of space. A Control Console/Pump Panel will be provided at the pump with the following controls: Start / Stop Switch, Throttle, oil pressure gauge, engine water temperature gauge, main water inlet compound gauge, main water outlet pressure gauge, tank to pump valve switch, 1.75 preconnect line valve switch, 2.5 discharge line valve switch, 1.5 tank fill line valve switch, foam system control, and water level indicator. A Control Console will be provided in the cab with the following controls: Start, Stop Switch, Throttle, oil pressure gauge, pump engine water temperature gauge, main water outlet pressure gauge, tank to pump valve switch, 2.0 front bumper remote controlled nozzle line valve switch, controls for front mounted remote controlled nozzle, foam system control, and tank water level indicator. 3 tank to pump line will be installed with ¼ turn electric ball valve located at the tank. A check valve will be installed between the valve and the pump with the check towards the tank. A 3 inlet with male NHT and 3 X 2-1/2 male NHT (2-1/2 C&O Thread may be substituted) adapter with cap will be provided at the rear of the truck. ( 3 Pipimg Will be used regardless of which pump is installed.) A 2-1/2 Discharge will be placed at the rear of the truck near the 3 Suction. This Discharge will have a quarter turn manual valve and equipped with male NHT and Capped with a 2-1/2 X 1-1/2 reducing cap with 1-1/2 cap. (2-1/2 C&O (3.292.X 8) adapter may be required by some companies. A 1-1/2 discharge with quarter turn ball valve will be placed near the 2-1/2 discharge. This will be 1-1/2 Male NHT with cap. A live booster reel will be mounted on the left rear corner of the truck bed to accommodate 200 of 1 booster line. The Booster Line and nozzle will be provided by body builder. Nozzle to be Task force Tip with valve nozzle with break-apart to allow for live

6 transfer to extension line. (Reel Tex Booster Line is preferred by most. Option may allow other makes of booster line.) An extension of the front bumper with brush guard and space to properly mount a remote controlled nozzle. (Sidewinder Remote Controlled Wildland Monitor 2.0 NPT female inlet and 1.5 NHT male outlet with 30 GPM Stream/Fog nozzle. A Push Bar Brush protection system will be installed to protect the Grill, head lights and radiator. Fire Suppression Unit to be equipped with drains that will allow for full freeze protection of unit. A rear step to allow for easy accesses to the top of the fire suppression unit. Emergency Lighting: LightBar: Whelen B-Link LED Liberty Light Bar. Light Bar to be Mounted on top of Cab Protection Bar Grill Lights: Red Whelen 500 LED mounted on the front Bumper Front Fender Cornering Lights: Red Whelen 500 LED mounted on the front Fenders Rear Body Lights: Red Whelen 500 LED 2 mounted under the side of the body. 2 mounted under the rear of the body. Rear Body Lights: Amber Whelen 500 LED 2 mounted under the rear of the body. Siren: Whelen WS Watt with Speaker mounted on front bumper. 12 Volt Scene Lighting to be provided by Fire Research FC-530- D-15 Focus Lights (2 mounted as instructed and remote controlled from pump panel and cab of truck)