Celsius 355 NH technical guide Structural hollow sections
|
|
- Miles Pope
- 5 years ago
- Views:
Transcription
1 Celsius 355 NH technical guide Structural hollow sections
2 Contents 03 Introduction 04 echnical data 08 Size range charts 12 Sectional properties Celsius 355 Circular 16 Sectional properties Celsius 355 Elliptical 18 Sectional properties Celsius 355 Square 22 Sectional properties Celsius 355 Rectangular 02
3 Celsius 355 NH echnical Guide CELSIUS 355 NH Celsius 355 hot finished hollow section is manufactured exclusively from normalised, fine grain steel for outstanding performance. Where failure is not an option, you can trust Celsius 355 to deliver. Celsius 355 key features: Normalised fine grain steel, so free of internal stresses and with a minimum strength of 355 MPa allowing the highest fabrication factors and enabling material cost savings and lighter structures Available in a wide range of circular, square, rectangular and elliptical hollow sections ight corner radii, exceeding the standard - enhancing the product s aesthetic appeal whilst avoiding the risk of brittle fracture which occurs in some cold formed products Dimensional consistency, high levels of formability and, because the steel is fullykilled, excellent weldability Certified as suitable for all structural applications, fully compliant with design codes and overcomes design risks associated with other forms of hollow sectons Certified as suitable for mechanical applications, especially those involving cyclical loading Suitable for low temperature applications -20 C) Batch-tested to give the properties of the specific delivered material; full test certification supplied Clearly marked as Celsius 355, with the reassurance of batch traceability Full technical support available Excellent supply availability through approved stockholders All Celsius 355 material is CE marked and is fully compliant with the Construction Products Regulation Suitable for galvanising 03
4 Celsius 355 NH echnical Guide echnical data ECHNICAL DAA High strength hot finished hollow sections suitable for all construction and mechanical applications. Celsius 355 is suitable for all internal and external applications to BS5950-1:2000, EN1993 and BS5400. Celsius 355 hollow sections are supplied with a minimum yield strength of 355 N/mm 2 and comply fully with the European Standard for hot finished structural hollow sections, EN10210: S355NH. Mechanical properties ield strength ensile strength Elongation % min Impact strength Carbon R eh min N/mm 2 R m N/mm 2 L 0 = 5,65 S 0 10mm x 10mm equivalent specimen (CEV) max 16mm 3mm < 100mm ºC J Chemical composition % by mass C Si Mn P S Nb V Al total i Cr Ni Mo Cu N max max max max max ma min* max max max max max max Celsius 355 is produced from fully-killed steel critical to formability and weldability. *If sufficient N-binding elements are present, the minimum total Al content does not apply. Inspection and testing Celsius 355 hollow sections EN10210: S355NH are subject to specific inspection and testing and are supplied with an inspection certificate type 3.1 to EN Designation Celsius 355 hollow sections are designated by their product name, outside dimensions and thickness in millimetres. CE marking All Celsius 355 material is CE marked and is fully compliant with the Construction Products Regulation. Examples Circular hollow section: Celsius x 6.3 or x 6.3 CHS EN10210: Part 1: S355NH Rectangular hollow section: Celsius x 50 x 5.0 or 100 x 50 x 5.0 RHS EN10210: Part 1: S355NH Elliptical hollow section: Celsius 355 elliptical 400 x 200 x 8.0 or 400 x 200 x 8.0 EHS EN10210: Part 1: S355NH or simply Celsius 355 EHS 400 x 200 x
5 Dimensional tolerances EN10210: Part 2 Circular/Ellipticals Square/Rectangular Outside dimension (D B and H) Circular ±1% with a min of ±0.5mm and maximum of ±10mm ±1% with a min of ±0.5mm Ellipticals ±1% with a min of ±0.5mm (he permitted tolerance is twice the value for H<250) hickness () -10% -10% Note: Positive deviation limited by mass tolerance Note: Positive deviation limited by mass tolerance Squareness of side 90 degrees ±1 degree External corner profile 2 max at each corner* (EN10210 has 3 max) Concavity/convexity (x) ±1% of the side, measured independently of the tolerance on the outside dimension wist (V) Ellipticals: 2mm plus 0.5mm/m max 2mm plus 0.5mm/m max (he permitted tolerance is twice the value for H<250) Section is placed on a flat surface with one end held flat. At the other end the height difference of the two lower corners is taken Mass (M) ±6% on individual lengths ±6% on individual lengths Straightness Maximum 0.2% of the total length & 3mm over every Maximum 0.2% of total length & 3mm over every 1m length 1m length Ellipticals: he permitted tolerance is twice the value for H<250 Length +150mm/-0mm +150mm/-0mm Out-of-roundness (O) Circular 2% for hollow sections having a diameter to thickness ratio not exceeding 100 * Unless shown otherwise 05
6 Celsius 355 NH echnical Guide echnical data Celsius 355 Square Hollow Sections length and tolerances Size hickness Standard mill lengths Special mill lengths olerance mm mm m m** mm 40 x 40 uti 100 x 100 All 6.0, 6.4, 7.5, 10.0 & x 120 uti 150 x 150 x 12.5 All 6.0, 6.4, 7.5, 10.0 & x 150 x 16.0 All Check availability x 160 uti 400 x 400 x 16.0 All 10.0 & x 400 x 20.0 All subject to availability (uti up to and including) Celsius 355 Rectangular Hollow Sections length and tolerances Size hickness Standard mill lengths Special mill lengths olerance mm mm m m** mm 50 x 30 uti 120 x 80 All 6.0, 6.4, 7.5, 10.0 & x 100 uti 200 x 100 x 12.5 All 6.0, 6.4, 7.5, 10.0 & x 100 x 16.0 All Check availability x 120 uti 500 x 300 x 16.0 All 10.0 & x 300 x 20.0 All subject to availability (uti - up to and including) Celsius 355 Circular Hollow Sections length and tolerances Outside diameter hickness Standard mill lengths Special mill lengths olerance mm mm m m** mm All 6.0, 6.4 & *42.4 All 6.0, 6.4, 7.5, 10.0 & * All 6.0, 6.4, 7.5, 10.0 & All 6.0, 7.5, 10.0 & All 6.0, 7.5, 10.0 & All 6.0, 7.5, 10.0 & All 10.0 & Celsius 355 Elliptical Hollow Sections length and tolerances Size hickness Standard mill lengths Special mill lengths olerance mm mm m m** mm 150 x 75 All 7.5, 10.0 & x 100 All 7.5, 10.0 & x 125 All 7.5, 10.0 & x 150 All 10.0 & x 200 All 10.0 & x 250 All 10.0 & ** For thinner gauge material, check standard lengths ** Lengths available in 100mm increments 06
7 07
8 Celsius 355 NH echnical Guide Size range charts SIZE RANGE CHARS Celsius 355 Circular Hollow Sections Outside Diameter (mm) hickness (mm) he above table shows our normal capability, reference should be made to the sectional properties table to identify sizes that are readily available and should be given preference. Minimum order quantities may apply to some sizes. Other sizes can be manufactured please contact your account manager. 08
9 Celsius 355 Elliptical Hollow Sections Size (mm) 150 x x x x x x 250 hickness (mm) Celsius 355 Square Hollow Sections Size (mm) 40 x x x x x x x x x x x x x x x x x x 400 hickness (mm) For sizes shown please contact your account manager. 09
10 Celsius 355 NH echnical Guide Size range charts Celsius 355 Rectangular Hollow Sections Size (mm) 50 x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x 300 hickness (mm) he above table shows our normal capability, reference should be made to the sectional properties table to identify sizes that are readily available and should be given preference. Minimum order quantities may apply to some sizes. Other sizes can be manufactured please contact your account manager. For sizes shown please contact your account manager. 10
11 11
12 Celsius 355 NH echnical Guide Sectional properties Celsius 355 circular Z CELSIUS 355 CIRCULAR D Celsius 355 EN10210: S355NH Hot finished circular hollow section Outside hickness Mass Sectional Moment Radius Elastic Plastic orsional Superficial Approx. Diameter area of inertia of gyration modulus modulus constants area/m length D M A I i W el W pl I t C t A s /tonne mm mm kg/m cm 2 cm 4 cm cm 3 cm 3 cm 4 cm 3 m 2 /m m/t
13 Z D Celsius 355 EN10210: S355NH Hot finished circular hollow section (continued) Outside hickness Mass Sectional Moment Radius Elastic Plastic orsional Superficial Approx. Diameter area of inertia of gyration modulus modulus constants area/m length D M A I i W el W pl I t C t A s /tonne mm mm kg/m cm 2 cm 4 cm cm 3 cm 3 cm 4 cm 3 m 2 /m m/t he dimensions shown in blue are standard sizes and should be given preference All other sizes are non-standard and therefore minimum order quantities may apply 13
14 Celsius 355 NH echnical Guide Sectional properties Celsius 355 circular Z D Celsius 355 EN10210: S355NH Hot finished circular hollow section (continued) Outside hickness Mass Sectional Moment Radius Elastic Plastic orsional Superficial Approx. Diameter area of inertia of gyration modulus modulus constants area/m length D M A I i W el W pl I t C t A s /tonne mm mm kg/m cm 2 cm 4 cm cm 3 cm 3 cm 4 cm 3 m 2 /m m/t
15 Z D Celsius 355 EN10210: S355NH Hot finished circular hollow section (continued) Outside hickness Mass Sectional Moment Radius Elastic Plastic orsional Superficial Approx. Diameter area of inertia of gyration modulus modulus constants area/m length D M A I i W el W pl I t C t A s /tonne mm mm kg/m cm 2 cm 4 cm cm 3 cm 3 cm 4 cm 3 m 2 /m m/t he dimensions shown in blue are standard sizes and should be given preference All other sizes are non-standard and therefore minimum order quantities may apply 15
16 Celsius 355 NH echnical Guide Sectional properties Celsius 355 elliptical B CELSIUS 355 ELLIPICAL Z H Celsius 355 EN10210: S355NH Hot finished elliptical hollow section Size hickness Mass Sectional Moment Radius Elastic Plastic orsional Superficial Approx area of inertia of gyration modulus modulus constants area/m length H x B M A I yy I zz i yy i zz W el,yy W el,zz W pl,yy W pl,zz I t C t A s /tonne mm mm kg/m cm 2 cm 4 cm 4 cm cm cm 3 cm 3 cm 3 cm 3 cm 4 cm 3 m 2 /m m/t 150 x x x x x x All above sizes are non-standard and therefore minimum order quantities may apply. 16
17 17
18 Celsius 355 NH echnical Guide Sectional properties Celsius 355 square B CELSIUS 355 SQUARE B Z Celsius 355 EN10210: S355NH Hot finished square hollow section Size hickness Mass Sectional Moment Radius Elastic Plastic orsional Superficial Approx. area of inertia of gyration modulus modulus constants area/m length B x B M A I i W el W pl I t C t A s /tonne mm mm kg/m cm 2 cm 4 cm cm 3 cm 3 cm 4 cm 3 m 2 /m m/t 40 x x x x x x
19 B B Z Celsius 355 EN10210: S355NH Hot finished square hollow section (continued) Size hickness Mass Sectional Moment Radius Elastic Plastic orsional Superficial Approx. area of inertia of gyration modulus modulus constants area/m length B x B M A I i W el W pl I t C t A s /tonne mm mm kg/m cm 2 cm 4 cm cm 3 cm 3 cm 4 cm 3 m 2 /m m/t 100 x x x x he dimensions shown in blue are standard sizes and should be given preference All other sizes are non-standard and therefore minimum order quantities may apply 19
20 Celsius 355 NH echnical Guide Sectional properties Celsius 355 square B B Z Celsius 355 EN10210: S355NH Hot finished square hollow section (continued) Size hickness Mass Sectional Moment Radius Elastic Plastic orsional Superficial Approx. area of inertia of gyration modulus modulus constants area/m length B x B M A I i W el W pl I t C t A s /tonne mm mm kg/m cm 2 cm 4 cm cm 3 cm 3 cm 4 cm 3 m 2 /m m/t 160 x x x x
21 B B Z Celsius 355 EN10210: S355NH Hot finished square hollow section (continued) Size hickness Mass Sectional Moment Radius Elastic Plastic orsional Superficial Approx. area of inertia of gyration modulus modulus constants area/m length B x B M A I i W el W pl I t C t A s /tonne mm mm kg/m cm 2 cm 4 cm cm 3 cm 3 cm 4 cm 3 m 2 /m m/t 300 x x x # he dimensions shown in blue are standard sizes and should be given preference All other sizes are non-standard and therefore minimum order quantities may apply # SAW Process (single longitudinal seam weld, slightly proud) 21
22 Celsius 355 NH echnical Guide Sectional properties Celsius 355 rectangular B CELSIUS 355 RECANGULAR Z H Celsius 355 EN10210: S355NH Hot finished rectangular hollow section Size hickness Mass Sectional Moment Radius Elastic Plastic orsional Superficial Approx area of inertia of gyration modulus modulus constants area/m length H x B M A I yy I zz i yy i zz W el,yy W el,zz W pl,yy W pl,zz I t C t A s /tonne mm mm kg/m cm 2 cm 4 cm 4 cm cm cm 3 cm 3 cm 3 cm 3 cm 4 cm 3 m 2 /m m/t 50 x x x x x x
23 B H Z Celsius 355 EN10210: S355NH Hot finished rectangular hollow section (continued) Size hickness Mass Sectional Moment Radius Elastic Plastic orsional Superficial Approx area of inertia of gyration modulus modulus constants area/m length H x B M A I yy I zz i yy i zz W el,yy W el,zz W pl,yy W pl,zz I t C t A s /tonne mm mm kg/m cm 2 cm 4 cm 4 cm cm cm 3 cm 3 cm 3 cm 3 cm 4 cm 3 m 2 /m m/t 120 x x x x x he dimensions shown in blue are standard sizes and should be given preference All other sizes are non-standard and therefore minimum order quantities may apply 23
24 Celsius 355 NH echnical Guide Sectional properties Celsius 355 rectangular B H Z Celsius 355 EN10210: S355NH Hot finished rectangular hollow section (continued) Size hickness Mass Sectional Moment Radius Elastic Plastic orsional Superficial Approx area of inertia of gyration modulus modulus constants area/m length H x B M A I yy I zz i yy i zz W el,yy W el,zz W pl,yy W pl,zz I t C t A s /tonne mm mm kg/m cm 2 cm 4 cm 4 cm cm cm 3 cm 3 cm 3 cm 3 cm 4 cm 3 m 2 /m m/t 180 x x x x x
25 B H Z Celsius 355 EN10210: S355NH Hot finished rectangular hollow section (continued) Size hickness Mass Sectional Moment Radius Elastic Plastic orsional Superficial Approx area of inertia of gyration modulus modulus constants area/m length H x B M A I yy I zz i yy i zz W el,yy W el,zz W pl,yy W pl,zz I t C t A s /tonne mm mm kg/m cm 2 cm 4 cm 4 cm cm cm 3 cm 3 cm 3 cm 3 cm 4 cm 3 m 2 /m m/t 250 x x x he dimensions shown in blue are standard sizes and should be given preference All other sizes are non-standard and therefore minimum order quantities may apply 25
26 Celsius 355 NH echnical Guide Sectional properties Celsius 355 rectangular B H Celsius 355 EN10210: S355NH Hot finished rectangular hollow section (continued) Z Size hickness Mass Sectional Moment Radius Elastic Plastic orsional Superficial Approx area of inertia of gyration modulus modulus constants area/m length H x B M A I yy I zz i yy i zz W el,yy W el,zz W pl,yy W pl,zz I t C t A s /tonne mm mm kg/m cm 2 cm 4 cm 4 cm cm cm 3 cm 3 cm 3 cm 3 cm 4 cm 3 m 2 /m m/t 300 x x x x x x
27 B H Celsius 355 EN10210: S355NH Hot finished rectangular hollow section (continued) Z Size hickness Mass Sectional Moment Radius Elastic Plastic orsional Superficial Approx area of inertia of gyration modulus modulus constants area/m length H x B M A I yy I zz i yy i zz W el,yy W el,zz W pl,yy W pl,zz I t C t A s /tonne mm mm kg/m cm 2 cm 4 cm 4 cm cm cm 3 cm 3 cm 3 cm 3 cm 4 cm 3 m 2 /m m/t 400 x x x x x x # # SAW Process (single longitudinal seam weld, slightly proud) he dimensions shown in blue are standard sizes and should be given preference All other sizes are non-standard and therefore minimum order quantities may apply 27
Hybox 355 technical guide Structural hollow sections
Hybox 355 technical guide Structural hollow sections Contents 03 Introduction 04 Technical data 06 Size range charts 08 Sectional properties Hybox 355 Circular 11 Sectional properties Hybox 355 Square
More informationCorus Tubes. Celsius. 355 Technical Guide. Structural Hollow Sections
Corus Tubes Celsius 355 Technical Guide Structural Hollow Sections Contents 01 Introduction 02 Technical data 06 Production range charts 08 Sectional Properties Celsius 355 Circular 10 Sectional Properties
More informationBS EN :2006. Hot finished structural hollow sections of non alloy and fine grain steels
. BS EN 1010 :006 Hot finished structural hollow sections of non alloy and fine grain steels 1 Scope This part of EN 1010 specifies tolerances for hot finished circular, square, rectangular and elliptical
More informationBS EN Cold formed welded structural hollow sections of non alloyb and fine grain steels Tolerances, dimensions and sectional properties
BS EN 10219 2 Cold formed welded structural hollow s of non alloyb and fine grain steels Tolerances, dimensions and al properties 1 Scope This part of EN 10219 specifies tolerances for cold formed welded
More informationSTEEL TUBES, PIPES, COILS AND PLATES
STEEL TUBES, PIPES, COILS AND PLATES About Us Tiger Steel Industries LLC, was established in 1997 in Dubai, UAE, primarily to manufacture ERW Tubes and Pipes for the Steel and Construction industry. The
More informationArcelorMittal Europe - Long products Sections and Merchant Bars HISTAR. Innovative high strength steels for economical steel structures
ArcelorMittal Europe - Long products Sections and Merchant Bars HISTAR Innovative high strength steels for economical steel structures Shanghai World Finance Center, P.R. China Innovative high strength
More informationContents
Contents 1 2-3 4 5 6-7 8 9 10 11 12 13 14 15-19 20-26 27 28 29 30 31 32 33 A Word about Steel Pipe Company Profile & Premises and Plants of Melewar Steel Tube Sdn. Bhd. Main Products Quality Products Quality
More informationCERTIFIED TO ISO 9001:2008 CERT NO:AR 0994
CERTIFIED TO ISO 9001:2008 CERT NO:AR 0994 www.melewar-mig.com MELEWAR STEEL TUBE SDN. BHD. (111059-D) Lot 53 Persiaran Selangor, 40200 Shah Alam, Selangor Darul Ehsan. Malaysia Tel : 603-5519 2455 (12
More informationSeamless hot rolled tubes and seamless hollow bars
Seamless hot rolled tubes and seamless hollow bars Benteler Distribution Customised steel tube solutions An internationally operating stockholding company of carbon alloy and stainless steel tubes With
More informationCold formed welded structural hollow sections of non-alloy and fine grain steels
BRITISH STANDARD BS EN 10219-2:2006 Cold formed welded structural hollow sections of non-alloy and fine grain steels Part 2: Tolerances, dimensions and sectional properties The European Standard EN 10219-2:2006
More informationNATIONAL TUBE STOCKHOLDERS LTD (NTS)
1 NATIONAL TUBE STOCKHOLDERS LTD (NTS) Welcome to our NTS Linepipe Products brochure. NTS are one of the UK s leading stockholders of Linepipe products. Operating for more than 30 years from a 37,000m
More informationDelivery program for steel pipes
Delivery program for steel pipes Table of content Photo: Herrenknecht AG 1. Water-bearing steel tubes 4 EN 10255 EN 10224 2. Seamless steel tubes for pressure purposes 6 EN 10216-1 bzw. EN 10216-3 EN 10216-2
More informationÅLASTRON S.A. Ag. Ioannis str., Ag. Ioannis Aspropyrgos Tel.: Fax:
ÅLASTRON S.A. Ag. Ioannis str., Ag. Ioannis 193 00 Aspropyrgos Tel.: +30 210 5515000 Fax: +30 210 5515015 www.elastron.gr elastron@elastron.gr 1 RECTANGULAR HOLLOW SECTIONS (EN 10219) Dimensions Cross
More informationHPL Tubes. Seamless Precision Steel Tubes for Hydraulic and Pneumatic Pressure Lines
HPL Tubes Seamless Precision Steel Tubes for Hydraulic and Pneumatic Pressure Lines 2 HPL Tubes Hydraulic-pneumatic pressure lines Mannesmann Precision Tubes As a leading European manufacturer of cold-drawn
More informationHPL Tubes Seamless Precision Steel Tubes for Hydraulic and Pneumatic Pressure Lines
HPL Tubes Seamless Precision Steel Tubes for Hydraulic and Pneumatic Pressure Lines 2 HPL Tubes Hydraulic-pneumatic pressure lines Salzgitter Mannesmann Precision SMP-Group As a leading European manufacturer
More informationProduct Range Handbook
Product Range Handbook 1 Where to find us Building 144 Culham Number 1 Site Station Road CULHAM Oxon OX14 3DA Sales: +44 (0)1865 409300 Fax: +44 (0)1865 407991 2 INDEX PAGE ROUND BARS 4 SQUARE BAR 5 TEES
More informationLong products and wire rod
production prograe Long products and wire rod Mittal Steel Ostrava a.s. production prograe Long products and wire rod Mittal Steel Ostrava a.s. Mittal Steel Ostrava a.s. TRADITIONAL PRODUCER OF THE HIGH
More informationBENTELER Distribution. Pipe solutions to the petrochemical and power generation sectors
BENTELER Distribution Pipe solutions to the petrochemical and power generation sectors About us BENTELER Distribution is an internationally operating stockholding and processing company of steel tubes
More informationBIMEE-007 B.Tech. MECHANICAL ENGINEERING (BTMEVI) Term-End Examination December, 2013
No. of Printed Pages : 5 BIMEE-007 B.Tech. MECHANICAL ENGINEERING (BTMEVI) Term-End Examination December, 2013 0 0 9 0 9 BIMEE-007 : ADVANCED DYNAMICS OF MACHINE Time : 3 hours Maximum Marks : 70 Note
More informationSteel Sheet Piling. Sales Program EDITION 2007
Steel Sheet Piling Sales Program EDITION 2007 ZSECTIONS 2. T he essential characteristicsof the Zsheetpile. are the continuous form ofthe weband the specificlocation of the interlock AZ smmetricall on
More informationData sheet: S3 Bar and structural products Profiles, dimensions & tolerances. Introduction
Data sheet: S3 Bar and structural products Profiles, dimensions & tolerances Introduction ArcelorMittal South Africa, Vereeniging Works produces a wide variety of long and forged products. Products are
More informationTalk to us. We ve got it! Tubecon Africa (PTY) LTD Reg. No. 1977/001592/07. Head Office: Cape Town: Durban: Tel Tel.
Talk to us. We ve got it! Tubecon Africa (PTY) LTD Reg. No. 1977/001592/07 Head Office: Cape Town: Durban: Piet Rautenbach Steet Tel. +27 12 541-3211 Tel. +27 21 949-0658 Tel. +27 31 701-6078 P.O. Box
More informationPRODUCTS HOT ROLLED REINFORCING BARS WIDE ROD BILLET FROM CONTINUOUS CASTING WELDED WIRE MESH
PRODUCTS HOT ROLLED REINFORCING BARS WIDE ROD BILLET FROM CONTINUOUS CASTING WELDED WIRE MESH INDEX 01. HOT ROLLED REINFORCING BARS PAGE 4 02. WIRE ROD PAGE 6 03. BILLET FROM CONTINUOUS CASTING PAGE 8
More informationJIS G4051 Carbon steel for Machine Structural Use
JIS G4051 Carbon steel for Machine Structural Use 1. Scope This Japanese Industrial Standard specifies the carbon steels for machine structural use manufactured by hot forming, such as hot rolling or hot
More informationProfile series I-40. System kit Profile series I-40
Profile series I-40 System kit Profile series I-40 n n n a n n n R n a R 45 Profile series I-40 Contents 1 Technical data/profile machining F f Page 1 2 Page 1 3 Page 1 5 Page 1 8 Profiles Page 2 2 3000
More informationHydraulic and pneumatic lines EN Zista and Zistaplex
Cold finished seamless tubes Hydraulic and pneumatic lines EN 10305-4 Zista and Zistaplex Distribution Benteler Distribution Customised steel tube solutions An internationally operating stockholding company
More informationBulb flats For plate stiffening
Corus Special Profiles Bulb flats For plate stiffening Introduction Plate stiffening 2 Bulb flats Introduction Bulb flats are tailor made for plate stiffening applications. Their special shape provides
More informationSteel technology Elastic properties of steel 1071 European standards for structural steels 1072
Appendix Steel technology Elastic properties of steel 1071 European standards for structural steels 1072 Design theory Bending moment, shear and deflection 1077 Bending moment and reaction 1102 Influence
More informationPRODUCT CATALOGUE. February we ll see it through
PRODUCT CATALOGUE February 2018 Orrcon Steel is a leading Australian distributor and manufacturer of Steel, Tube and Pipe. We have distribution centres in six Australian states and a number of Orrcon Steel
More informationBulb Flats. Light weight corrosion resistant solution for plate stiffening
Bulb Flats Light weight corrosion resistant solution for plate stiffening 2 CRANE BULB FLATS RAIL Photo courtesy of: Andrew Linnett/MOD Introducing British Steel British Steel is a world leader in the
More informationPRODUCT CATALOGUE LOUCON METAL LTD. 37 and 39 Grenfell Crescent, Nepean, ON K2G 0G3. Hours of Operation: Monday-Friday 8:00 AM 5:00 PM
PRODUCT CATALOGUE 37 and 39 Grenfell Crescent, Nepean, ON K2G 0G3 Hours of Operation: Monday-Friday 8:00 AM 5:00 PM Phone: (613) 226-1102 Fax: (613) 226-6097 e-mail: info@louconmetal.com web: www.louconmetal.com
More informationSmall Tool Instruments and Data Management
Small Tool Instruments and Data Management Gauge Blocks Pages 302 311 Calibration instruments Pages 312 319 301 Basic information on gauge blocks Characteristics of Mitutoyo gauge blocks: Mitutoyo, at
More information3.1 Available sections, terms of delivery
3.1 Interlocks LARSSEN section Interlock design conforming to DIN EN 10248-2 and E 67 of EAU 2004 LARSSEN 43, 430 HOESCH section (LARSSEN interlock) Interlock design conforming to DIN EN 10248-2 and E
More informationDrilmax Steel Tubes. for the most demanding mining exploration drilling conditions
Drilmax Steel Tubes for the most demanding mining exploration drilling conditions Customer Benefits Drilmax steel tubes are cold drawn, heat-treated and straightened with the highest expertise to offer
More information*) experts for experts. Seamless and welded cold drawn precision steel tubes. voestalpine Rotec 1
*) experts for experts. Seamless and welded cold drawn precision steel tubes voestalpine Rotec www.voestalpine.com/rotec 1 Innovative and successful solutions are always within your reach with voestalpine
More informationComparison ISO / ANSI Piping System
Comparison ISO / ANSI Piping System Driving cost savings without compromise 1 2 Why is it preferable to select the ISO Piping standard instead of ANSI? 1. General Stainless steel pipes are widely used
More informationTechnical Data MM Channel
Technical Data MM Channel The enclosed pages are taken from the Installation Systems Catalogue 2015 for additional information please visit the technical library at www.hilti.co.uk or call our Technical
More information*) experts for experts. Seamless and welded cold drawn precision steel tubes
*) experts for experts. Seamless and welded cold drawn precision steel tubes 1 Innovative and successful solutions are always within your reach with voestalpine Rotec, your reliable partner with professional
More informationHours / 100 Marks Seat No.
17610 16172 4 Hours / 100 Seat No. Instructions (1) All Questions are Compulsory. (2) Answer each next main Question on a new page. (3) Illustrate your answers with neat sketches wherever necessary. (4)
More informationEXPORTERS OF ENG MATERIALS & FABRICATIONS
EXPORTERS OF ENG MATERIALS & FABRICATIONS Certificate of Registration This is to certify that the Quality Management System of UK Steel Exports Limited Blackvein Industrial Estate, Cross Keys, Newport,
More informationARCELORMITTAL TUBULAR PRODUCTS IASI Product portfolio European standards
ARCELORMITTAL TUBULAR PRODUCTS IASI Product portfolio European standards 1 ARCELORMITTAL TUBULAR PRODUCTS IASI 1. TUBES FOR INSTALLATIONS - EN 10255 - Unalloyed steel pipes for welding and threading -
More informationEXAMPLES INTRODUCTION
AMEM 316 (AUTO308): Machine Elements I EXAMPLES INTRODUCTION EXAMPLES INTRODUCTION Example 1 (Hamrock p.53) As shown in figure 2.12(a), a 3m long bar is supported at the left end (B) by a 6 ram diameter
More informationWide Flange Beams for offshore structures
Wide Flange Beams for offshore structures S355 G11/G12 +M and Hi355 TZK Weldability evaluation in accordance with EN 10225 June 2012 Content Base metal characterization (Appendix 1 : certificate) Identification
More informationForklift Profiles. Mast sections and fork arm flats for material handling equipment
Forklift Profiles Mast sections and fork arm flats for material handling equipment Introducing British Steel British Steel is one of the leading steel manufacturers in Europe, producing around 3 million
More informationFull Traceability. Material Specification. Raw Material Code. Heat Treatment
All J.B. Smith swages, bull plugs, tubing and casing nipples, and chambers are traceable to the original mill test report. To ensure traceability, all fittings are steel stamped as follows: Material Specification
More informationCODE 10 OECD STANDARD CODE FOR THE OFFICIAL TESTING OF FALLING OBJECT PROTECTIVE STRUCTURES ON AGRICULTURAL AND FORESTRY TRACTORS
CODE 10 OECD STANDARD CODE FOR THE OFFICIAL TESTING OF FALLING OBJECT PROTECTIVE STRUCTURES ON AGRICULTURAL AND FORESTRY TRACTORS 1 TABLE OF CONTENTS INTRODUCTION... 3 1. DEFINITIONS... 3 1.1 Agricultural
More informationPrecision Modules PSK
Precision Modules PSK The Drive & Control Company Rexroth Linear Motion Technology Ball Rail Systems Roller Rail Systems Standard Ball Rail Systems Super Ball Rail Systems Ball Rail Systems with Aluminum
More informationTable of Contents. Douglas Barwick
100 7 00 arwick c. 3 17 56 Ø100 9 200 56 200 Y EQUIP. SUPPLIER 500 ERED SLUDGE DIGESION NK No.1 60 60 X 69 650 3 17 500 50 Ø100 651 152 CON. ON D-170 GROU RING 6 x 50 (YP.2) ERED SLUDG2 DIGESION NK No.2
More informationTechnical Data Sheet. British Standards Compliant. TECHNICAL DATA SHEET System 160 (British Standards)
Technical Data Sheet British Standards Compliant Mass 10 System 160 Mass 25 Mass 50 MAT 75 / 125 Superprop Hydraulics Quickbridge MU Falsework MU Bridging Compact Bridging BarrierGuard 800 Instrumentation
More informationSteel Sheet Piles. PU-R Sections PU 8R PU 9R - 10R - 11R PU 13R - 14R - 15R t t t
Steel Sheet Piles PU-R s 49.5 t s 280 PU 8R 54.5 t s PU 9R - 10R - 11R 49.5 t s PU 13R - 14R - 15R Hot Rolled Steel Sheet Piles - Rodange, Luxembourg ArcelorMittal, the worldwide leader in steel sheet
More informationPiling Product Guide Edition. Servicesteel.org
Piling Product Guide 2017 Edition Strong Foundations Starith Service Steel Service Steel Supplies All Your Foundation Products You Are Our Number One Priority From industry leading steel sheet piling to
More informationDelivery program. Carbon steel and stainless steel tubes in a wide range of qualities and dimensions. Distribution
Delivery program Carbon steel and stainless steel tubes in a wide range of qualities and dimensions Distribution Our value proposition The reliable supply of high-quality steel tubes and customized service
More informationPrecision Modules PSK
Precision Modules PSK 2 Bosch Rexroth AG Precision Modules PSK R999000500 (2015-12) Identification system for short product names Short product name Example:: P S K - 050 - N N - 1 System = Precision Module
More informationMI250 HYDRAULIC MOTORS T E C H N I C A L C A T A L O G
MI250 HYDRAULIC MOTORS T E C H N I C A L C A T A L O G Hydraulic motors MI250 OCLAIN HYDRAULICS CHARACTERISTICS Theoretical torque Max.power Max.speed ressure max. at 100 bar at 1000 SI cm³/tr [cu.in/rev.]
More information2507 (IBC 2006 ONLY) 3054 (IBC 2006 ONLY) Supreme Framing System Product Catalog
12 0 2 / 2009IANT C B I PL COM 2507 (IBC 2006 ONLY) 3054 (IBC 2006 ONLY) R Supreme Framing System Product Catalog Supreme Framing System The Benefits of Supreme Framing System Speak for Themselves What
More informationSEVENTH EDITION HOT ROLLED AND STRUCTURAL STEEL PRODUCTS
SEVENTH EDITION HOT ROLLED AND STRUCTURAL STEEL PRODUCTS HOT ROLLED AND STRUCTURAL STEEL PRODUCTS CONTENTS INTRODUCTION 1 TEST CERTIFICATES AND 2 CERTIFICATES OF COMPLIANCE BUILD WITH STANDARDS AND ACRS
More informationMATERIALS FOR SALE OR RENT YOUR PARTNER IN INFRASTRUCTURE
YOUR PARTNER MATERIALS FOR SALE OR RENT IN INFRASTRUCTURE About Infrasteel InfraSteel is a large supplier of steel products from Europe and beyond. Customers can rely on our support for both large and
More informationSupreme. Supreme Framing System. Product Catalog IAPMO UNIFORM ER #0313
Supreme Supreme Framing System Product Catalog IAPMO UNIFORM ER #0313 2507 Table of Contents Certification of Materials 5 LEED Credits 5 Independent Product Certification 5 Code Approvals, Performance
More informationCopper-Nickel Alloy for Seawater Piping Systems (CuNi 90/10)
Offshore OSNA -10 Copper-Nickel Alloy for Seawater Piping Systems (CuNi 90/10) KME Germany GmbH & Co. KG Offshore OSNA -10 [GB] Content KME - The Company 1 The Material 2 Offshore Product Range 3 Pipes
More informationPurlins and Girts. A division of Canam Group
Purlins and Girts A division of Canam Group TABLE OF CONTENTS OUR SOLUTIONS AND SERVICES............................................................ 5 Cautionary statement..................................................................
More information4300 Catalog. Metric Tube. Parker Hannifin Corporation Tube Fittings Division Columbus, Ohio
Metric Tube Q 4300 Catalog Metric Tube Q2 4300 Catalog Metric Tube Introduction Parker offers three types of seamless metric tubes for hydraulic, pneumatic and instrumentation applications: dipped for
More informationIBC 2009/2012 COMPLIANT. Supreme Framing System. Product Catalog
IBC 2009/2012 COMPLIANT 2507 Supreme Framing System Product Catalog Supreme Framing System The Benefits of Supreme Framing System Speak for Themselves What is the Supreme Framing System? Supreme Framing
More informationÅLASTRON S.A. Ag. Ioannis str., Ag. Ioannis Aspropyrgos Tel.: Fax:
ÅLASTRON S.A. Ag. Ionnis str., Ag. Ionnis 193 00 Aspropyrgos Tel.: +30 210 5515000 Fx: +30 210 5515015 www.elstron.gr elstron@elstron.gr 1 SQUARE HOLLOW SECTIONS (EN 10219) Dimensions Cross section Weight
More informationGuideline No.: E-04(201510) E-04 GENERATORS. Issued date: October 20,2015. China Classification Society
Guideline No.: E-04(201510) E-04 GENERATORS Issued date: October 20,2015 China Classification Society Foreword: This Guideline is a part of CCS Rules, which contains technical requirements, inspection
More informationComponents: Dimensions / Order Codes Clamp Body. * 1st part of STAUFF Group 4. * Exact outside diameters Ø D1 / Ø D2 (mm) Clamp Body.
Components: Dimensions / Order Codes Clamp Body Clamp Body Colour: Green Material code: PP 4 PP One clamp body is consisting of two clamp halves. 1st part of STAUFF 4 Exact outside diameters Ø D1 / Ø D2
More informationTubacero Highlights 350,
www.tubacero.com Tubacero Highlights Installed rated capacity: 350,000 metric tons per year throughout 5 plants covering 4.7 million sq. ft. Products: Straight longitudinally welded carbon steel pipe,
More informationGuideline No.: E-04(201610) E-04 GENERATORS. Issued date: October 28,2016. China Classification Society
Guideline No.: E-04(201610) E-04 GENERATORS Issued date: October 28,2016 China Classification Society Foreword: This Guideline is a part of CCS Rules, which contains technical requirements, inspection
More informationDESFLEX COMPACT FLANGES
DESFLEX COMPACT FLANGES DESFLEX COMPACT FLANGES The first original Compact Flange designed in full accordance with ASME ANSI PD 5500, Type Approved & Fire Tested. Offering weight savings of up to 88% when
More informationCONVEYOR MANUFACTURERS ASSOCIATION OF SA LIMITED STATIC SHAFT CONVEYOR PULLEYS WITH INTERNAL BEARINGS FOR CONVEYORS
CONVEYOR MANUFACTURERS ASSOCIATION OF SA LIMITED STATIC SHAFT CONVEYOR PULLEYS WITH INTERNAL BEARINGS FOR CONVEYORS CMA MP01 Rev00 2013 Table of Contents 1 INTRODUCTION... 3 2 NORMATIVE REFERENCES... 3
More informationTRENCH SHIELDING AND SHORING
TRENCH SHIELDING AND SHORING PROSERIES SHIELDS PERFORMANCE DESIGNED FOR TOP PRODUCTIVITY The ProSeries line of trench shields from PRO-TEC incorporates performance features that help deliver outstanding
More informationESC H COMBINATION WALL
VIEW OUR 2016 PROJECT SHOWCASE VIDEO BY SCANNING THE QR CODE BELOW: ESC H COMBINATION WALL H-ESZ, H-CRZ, H-S SERIES A H Pile Combination Wall System consists of Steel H Piles that The ESC Advantage withstand
More informationUNIT-3 PART-A C.K.GOPALAKRISHNAN, AP/MECH, MAHALAKSHMI ENGINEERING COLLEGE, TRICHY
UNIT-3 PART-A 1. List the loads normally acting on a shaft? Bending load Torsional load or tw isting load. Axial thrust. 2. Write dow n the expression for the power transmitted by a shaft. P=2π NT/60 Where
More informationPeeled and Ground Round Steel Bars
pag. 1 of 9 Viale Certosa, 249-20151 Milano Tel: +39 02 30 700 - Fax: +39 02 38000 346 - Mail: commerciale.riva@rivagroup.com Production Units: Malegno (BS), Italy pag. 2 of 9 Products STRUCTURAL AND GENERAL
More informationUNIT IV DESIGN OF ENERGY STORING ELEMENTS. Prepared by R. Sendil kumar
UNIT IV DESIGN OF ENERGY STORING ELEMENTS Prepared by R. Sendil kumar SPRINGS: INTRODUCTION Spring is an elastic body whose function is to distort when loaded and to recover its original shape when the
More informationThe Amodil Group. Specialists In Stainless Steel Long Products
Specialists In Stainless Steel Long Products Specialists In Stainless Steel Long Products Round Hexagon Flat Square Angle Billet Seamless Pipe & Tube Hollow Bar Fittings Over 5,000 tonnes of Stainless
More informationVALLIAMMAI ENGINEERING COLLEGE DEPARTMENT OF MECHANICAL ENGINEERING ME6503 DESIGN OF MACHINE ELEMENTS QUESTION BANK
VALLIAMMAI ENGINEERING COLLEGE DEPARTMENT OF MECHANICAL ENGINEERING ME6503 DESIGN OF MACHINE ELEMENTS QUESTION BANK Unit -1 STEADY STRESSES AND VARIABLE STRESSES IN MACHINE MEMBERS Part-A 1. What are the
More informationStainless Steel Tubular Fittings Ultrahigh-Purity and Chemically Cleaned and Passivated
www.swagelok.com Stainless Steel ubular Fittings Ultrahigh-Purity and Chemically Cleaned and Passivated Sizes from 1/4 through 4 outside diameter Metric sizes available upon request 316L stainless steel
More informationDESIGN OF MACHINE MEMBERS - I
R10 Set No: 1 III B.Tech. I Semester Regular and Supplementary Examinations, December - 2013 DESIGN OF MACHINE MEMBERS - I (Mechanical Engineering) Time: 3 Hours Max Marks: 75 Answer any FIVE Questions
More informationOne Company, Three Businesses,Your Complete Solution! Product and Service Catalogue NSF61 G-372
One Company, hree usinesses,your Complete Solution! Product and Service Catalogue NSF61 G-372 arwick inc. he D Piping Group Over View... 1-1 SM 778 & 774 Suary of Specification... 2-1 Pipe... 2-2 90 Elbows...
More informationALUMINIUM EXTRUSION CATALOGUE
ALUMINIUM EXTRUSION CATALOGUE Contents 04 Geometric Sections 52 Extrusion Applications 126 Capral Aluminium Fabrication 130 Alloy, Temper and Mechanical Specifications B Who is Capral Aluminium and what
More informationCustom welded sections can be sourced within New Zealand (Steltech) within 4 to 6 weeks of order.
MATERIALS Steel Availability in New Zealand Author: Clark Hyland Affiliation: Steel Construction New Zealand Inc. Date: 28 th November 2007 Ref.: MAT1003 Key Words steel availability, procurement Introduction
More informationThe bonded pipe system Overview
2.0.0.1 Overview Introduction This section contains a description of the preinsulated single s which LOGSTOR offers. Contents Material specifications 2.0.1 District heating s, insulation series 1 2.0.2
More informationPrecision Modules PSK. The Drive & Control Company
Precision Modules PSK The Drive & Control Company 2 Bosch Rexroth Coporation Precision Modules PSK R310A 2414 (2008.07) Linear Motion and Assembly Technologies Ball Rail Systems Roller Rail Systems Linear
More informationEURO-BEARINGS LTD COMBINED ROLLER BEARINGS & MATING STEEL PROFILES CATALOGUE. Tel: +44 (0)
COMBINED ROLLER BEARINGS & MATING STEEL PROFILES CATALOGUE email: sales@euro-bearings.com Tel: +44 (0)1908 511733 2015 CATALOGUE CONTENTS COMBINED ROLLER BEARINGS Standard CR Bearings Eccentric Adjustable
More informationArcelorMittal Sheet Piling. The next generation of AZ sheet piles
ArcelorMittal Sheet Piling The next generation of AZ sheet piles Going wider! The new AZ sheet piling series b ArcelorMittal As the world leader in the production of hot-rolled sheet piles, ArcelorMittal
More informationMAE 322 Machine Design Shafts -3. Dr. Hodge Jenkins Mercer University
MAE 322 Machine Design Shafts -3 Dr. Hodge Jenkins Mercer University Setscrews Setscrews resist axial and rotational motion They apply a compressive force to create friction The tip of the set screw may
More informationwww.mainawatisteel.com 1 From The Chairman s Desk The journey of Mainawati was initiated very humbly in 1995 with a plant in Duhabi Bhalua Municipality of Sunsari district (Nepal) for manufacturing ERW
More informationHIGH STRENGTH, ECONOMICAL AND EXCELLENT QUALITY STEEL PIPE PILES DELIVERED TO YOUR EXPECTATIONS
ESC STEEL PIPE PILES LSAW, SSAW & ERW PIPES HIGH STRENGTH, ECONOMICAL AND EXCELLENT QUALITY STEEL PIPE PILES DELIVERED TO YOUR EXPECTATIONS Pipe Piles can be utilised in a multitude of applications: such
More informationIntroduction Elastomeric Bearing Expansion Joints Construction Profiles Projects
Table of contents Introduction Introduction Product Quality Elastomeric Bearing What Is Elastomeric Bearing? Types of Bearings & Usage Aspects and Architecture Constraining Movement Material Specifications
More informationMr.Giridhar Bosch Rexroth (India) Limited A Drive & Control Company. Cylinder Presentation
Mr.Giridhar Bosch Rexroth (India) Limited A Drive & Control Company Cylinder Presentation Introduction Good Morning Ladies & Gentlemen, We spend the next hour in understanding the Hydraulic Actuator Cylinder.
More information1-3/8" inside-to-inside dimension. length of the leg. S162
Member Designation MEMBER DEPTH: FLANGE WIDTH: STIFFENER LIP: Member Depths are taken in 1/100 inches. Flange Widths are taken in 1/100 inches. Member Flange Width Stiffener Lip (in) For Track Sections,
More informationIS&G STEEL STOCKHOLDERS LTD PRODUCT GUIDE
IS&G STEEL STOCKHOLDERS LTD PRODUCT GUIDE IS&G IS&G Steel Stockholders Ltd have been established for over eighty years. We have branches at Beckenham in Kent; Chelmsford in Essex and Ipswich in Suffolk.
More informationDEPARTMENT OF MECHANICAL ENGINEERING
DEPARTMENT OF MECHANICAL ENGINEERING UABMCC01-DESIGN OF MACHINE ELEMENTS QUESTION BANK Prepared By: Dr.S.Prabhakaran, Associate Professor/Mechanical Engg. Unit -1 STEADY STRESSES AND VARIABLE STRESSES
More informationkyin all shapes, sizes and standards
. kyin all shapes, sizes and standards Fittings from Alfa Laval - Tri-Clover Application Alfa Laval is your complete source for specialized fittings and tubing required in food, dairy, beverage, personal
More informationShaft Design. Dr. Mostafa Rostom A. Atia Associate Prof.
Shaft Design Dr. Mostafa Rostom A. Atia Associate Prof. 1 Loading modes A shaft is a rotating member, usually of circular cross section, used to transmit power or motion. It provides the axis of rotation,
More informationChapter 7. Shafts and Shaft Components
Chapter 7 Shafts and Shaft Components 2 Chapter Outline Introduction Shaft Materials Shaft Layout Shaft Design for Stress Deflection Considerations Critical Speeds for Shafts Miscellaneous Shaft Components
More informationCOMPARATIVE ANALYSIS OF CRANKSHAFT IN SINGLE CYLINDER PETROL ENGINE CRANKSHAFT BY NUMERICAL AND ANALYTICAL METHOD
COMPARATIVE ANALYSIS OF CRANKSHAFT IN SINGLE CYLINDER PETROL ENGINE CRANKSHAFT BY NUMERICAL AND ANALYTICAL METHOD Mr. Anant B. Khandkule PG Student Mechanical Engineering Department, Sinhgad Institute
More informationB.TECH III Year I Semester (R09) Regular & Supplementary Examinations November 2012 DYNAMICS OF MACHINERY
1 B.TECH III Year I Semester (R09) Regular & Supplementary Examinations November 2012 DYNAMICS OF MACHINERY (Mechanical Engineering) Time: 3 hours Max. Marks: 70 Answer any FIVE questions All questions
More informationShrink Discs, Smart-Lock & Shaft Couplings
RINGFEDER Products are available from MARYLAND METRICS Shrink Discs, Smart-Lock & Shaft Couplings US 08 2009 Partner for performance RINGFEDER Products are available from MARYLAND METRICS P.O. Box 261
More informationTechnical Product Manual
Technical Product Manual 2019 EDITION Unmatched Product Range Material Availability Manufacturg Capabilities Innovative Applications and Engeerg Expertise Your True Project Partner Unmatched Product Range
More information