Mr.Giridhar Bosch Rexroth (India) Limited A Drive & Control Company. Cylinder Presentation

Transcription

1 Mr.Giridhar Bosch Rexroth (India) Limited A Drive & Control Company Cylinder Presentation

2 Introduction Good Morning Ladies & Gentlemen, We spend the next hour in understanding the Hydraulic Actuator Cylinder. I am sure, during the lecture clause on basic principles of Hydraulics, you have already gathered that, there are reasons and advantages to use a Hydraulic System in designing industrial / mobile machines. The source of power such as an electric motor or an engine drives an hydraulic pump which delivers fluid under pressure. This fluid under pressure is used to create the necessary movements in the machine, linear, rotary or reciprocating. The movement is the desired end function to lift, press, shift or move hold / clamp, orient, turn etc.,

3 Hydraulic cylinder is the device to which, we supply the pressure oil from the pump and obtain linear movement to push, press, shift, clamp any load. Eg: Coal stacker reclaimer Pusher in a furnace in a steel shop. The boom of an exlavator The Dozer blade of a bull dozer The jacks of a water well rig pressing against the ground The telescopic cylinder of a rear dumper. The double ended cylinder in a surface grinding machine etc.,

4 Topics :- 1. Brief on hydraulic systems 2. The need for a device linear actuating high forces, compact size 3. Where do we use it? Applications 4. How does it work? 5. What is it made of? Design aspects 6. Materials of construction 7. How to size it for a specific applications calculations, selection criteria column strength, stop tube 8. Types of cylinders 9. Mounting configurations / special features 10.Cushioning Need, design and variations for it 11.Seals types, materials, selection criteria 12.Performance criteria, what to test? Test procedure 13.Trouble shooting / servicing aspects 14.Working medium Hydraulic oil, fire resistant fluids, synthetics, water, water glycol etc.,

5 Hydraulic cylinders - Principles

6 Tie rod type cylinder

7 Mill type cylinder (Heavy duty cylinder)

8 Tandem cylinder

9 Double acting rapid traverse cylinder

10 Single acting telescopic cylinder

11 Double acting telescopic cylinder

12

13

14

15

16

17

18

19

20

21

22

23

24

25

26

27

28

29

30

31 End position cushioning mechanism in cylinder

32 Procedure for determining the safe piston rod calculation : The two most relevant formulae used in determining the column strength of piston rod are: Euler s formula: Pc = r x ² x E x a = r x ² x E x I (L / r) ² L² Johnson s parabolic formula: Pc = a x y x [1-y x (L / r²) ] x x ² x E Pc = Critical or Buckling load, Kgf = Coefficient of end condition E = Young s modulus of the material of piston rod, Kgf/mm² a = Area of C/S of piston rod, mm² L = Column length, mm r = Least radius of gyration of piston rod, mm y = Yield stress of the material of piston rod, Kgf/mm² I = Moment of inertia of piston rod section, mm4

33 Cylinder wall thickness calculation: T = x d x p for C1 = ±125% x k / s - 2 x p C1= The tolerance on wall thickness S = Factor of safety (1.5 to 4 can be used) k = Yield strength (minimum) 36 kg/mm² for SE52 d = Inside diameter of tube, mm p = Pressure, kg/cm²

34 EXERCISES :- 1 What is the difference between a single-acting and a double acting hydraulic cylinder? 2 Name four different types of Hydraulic Cylinder mountings? 3 What is a cylinder cushion? What is its purpose? 4 What is a double-rod cylinder? When would it normally be used? 5 What is a telescoping rod cylinder? When would it normally be used? 6 Why does the rod of a double-acting cylinder retract at a greater velocity than it extends for the same input flow-rate?

35 7 How are single-acting cylinders retracted? 8 An 8 cm diameter hydraulic cylinder has a 4 cm diameter rod, if the cylinder receives flow at 100 lpm and 12 MPa, find the a) Extension and retraction speeds b) Extension and retraction load carrying capacities. 9 A 3 in diameter hydraulic cylinder has a 1.5 in diameter road, find the flow rate leaving the cylinder when it is extending by an entering flow rate of 8 gpm