International Motors/Gearmotors/Controls

Transcription

1 International Motors/Gearmotors/Controls

2 AC INTENATIONAL PODUCTS INTODUCTION The metric products listed in this section have been designed with international design standards in mind. The 230 volt, 50 Hz windings can be operated satisfactorily on any nominal system voltage between 220 and 240 volts to accommodate almost all international power supply requirements. Splashproof terminal boxes are standard on most AC products. Mounting and shaft configurations designed for common metric sizes provide convenient interfacing capability. CONSTUCTION ECOGNITION Most Bodine products are third party approved with respect to construction. Metric motors and gearmotors are designed to meet most requirements of BSI, IEC, and VDE. Their nameplates bear an IEC 34-1 designation. Motors, gearmotors and controls are recognized by U.L., Inc. and are registered in U.L. Construction recognition file No. E47177 and E Many stock products are also CSA certified and appear in CSA File No. L2797 and L Bodine metric motors and gearmotors also meet CE standards. See page 4 for more information. AC CONNECTIONS V 460 V ED BLACK BLUE WHITE GN-YEL T. (GD) LINE LINE WHITE BLUE ED BLACK GEEN/YELLOW LINE LINE T-1 BLACK T-6 ED/YELLOW T-2 BLUE T-4 BLACK/YELLOW T-3 ED T-5 BLUE/YELLOW LINE LINE LINE BLACK T-1 BLUE T-2 ED T-3 BLACK/YELLOW T-4 BLUE/YELLOW T-5 ED/YELLOW T-6 GEEN/YELLOW GEEN/YELLOW To reverse transpose the black and white leads. To reverse transpose the black and white leads To reverse transpose any leads or combinations K-2 MOTO 2.8 WATTS (3.8 MILLI. HP) For more information see page 14 Output Input adial Length Wt. Connection Capacitor Product Model Speed ated (Milli- Hz V Ph Amps Load mm (inch) kg (lbs.) Diagram Part No. Type Number (rpm) Torque W HP) N (lbs.) XH mnm (oz-in.) PEMANENT SPLIT CAPACITO (NOMAL SLIP), NON-SYNCHONOUS (3.0) 2.8 (3.8) (5.7) 63 (2.5) 1.1 (2.2) KCI XH 16.0 (0.63) 61.0 (2.41) SQ MIN. (0.39) (1.91) STANDAD LEADS / -25 (12+2/ -1) Ø 5 h6 (.19) 0.8 (0.03) 48.5 (1.91) ( 4) M4x0.7-6H, 4 mm deep minimum on a 68 mm bolt circle 82

3 AC INTENATIONAL PODUCTS 30 MOTOS WATTS (1/41-1/39 HP) (4) M5X.8-6H, 8mm deep minimum on a 95 mm bolt circle 34 MOTOS For optional terminal box model 1982, see page 100. Capacitor shown on page 30. Output Input adial Length Wt. Connection Capacitor Product Model Speed ated W (HP) Hz V Ph Amps Load mm (inch) kg (lbs.) Diagram Part No. 2 Type Number 1 Nm (oz-in.) PEMANENT SPLIT CAPACITO, NON-SYNCHONOUS (.9) 19 (1/39) (18) 93.7 (3.69) 2.1 (4.6) BECI (18) 18 (1/41) (18) 93.7 (3.69) 2.1 (4.6) BECI N (3.58) Shown with standard terminal box WATTS (1/10-1/7.5 HP) For more information see page 16 Output Input adial Length Wt. Connection Capacitor Product Model Speed ated W (HP) Hz V Ph Amps Load mm (inch) kg (lbs.) Diagram Part No. Type Number Nm (oz-in.) THEE PHASE, NON-SYNCHONOUS (97) 100 (1/7.5) / / (42) 168 (6.7) 4.4 (9.8) BFPP 1295 PEMANENT SPLIT CAPACITO, NON-SYNCHONOUS (72) 75 (1/10) (42) 168 (6.7) 4.4 (9.8) BFCI 1291 XH (4.02) (4.10) XH 3.1 (0.12) 2.3 (.09) 16.0 (0.63) 13.2 (0.52) 5.84 (0.23) Ø 7 h6 (0.28) 20.0 (.78) Ø9 h6 (.35) STANDAD LEADS /-25 (12 +2/-1) 3x3x14 (.12x.12x.55) KEY 67.1 (2.64) 53.1 (2.09) 86.6 (3.41) 67.3 (2.65) SQ. EF (.91) EF. For more information see page (Ø 1.97) 46.0 (1.81) EF (1.499) 38.0 (1.495) INTODUCTION INDEX INTENATIONAL BUSHLESS DC PEMANENT MAGNET DC INDUCTION AC M5X.8-6H, 8mm deep minimum on a 65 mm bolt circle 83

4 AC INTENATIONAL PODUCTS 42 MOTO Shown with standard terminal box WATTS (1/7.5-1/5 HP) For more information see page 17 Output Input adial Length Wt. Connection Capacitor Product Model Speed ated W (HP) Hz V Ph Amps Load mm (inch) kg (lbs.) Diagram Part No. Type Number Nm (oz-in.) THEE PHASE, NON-SYNCHONOUS (135) 140 (1/5) / / (50) 170 (6.7) 5.3 (11.8) _ 425BFPP 1273 PEMANENT SPLIT CAPACITO, NON-SYNCHONOUS (97) 100 (1/7.5) (50) 170 (6.7) 5.3 (11.8) BFCI 1358 XH 2.5 (0.09) (4.02) 7.9 (0.31) MIN. 7.1(.28) 56.9 (2.24) 42.7 Ø (4.72) (1.68) Ø 11 h6 (0.43) 23.0 (0.90) 4x4x16 KEY (0.16SQ X 0.63) 67.1 (2.64) Ø109.0 (4.29) Ø 60.0 (2.36) (2.62) (4.98) 53.1 (2.09) (4.53) 26.4 (1.04) 22.1 (0.87) 53.1 (2.09) EF (3.50) M5X.8-6H, 8 mm deep minimum on a 75 mm bolt circle K-2 GEAMOTO 24A.67 MOTO Nm (95 OZ-IN.) MAXIMUM For more information see page 19 Output Input Gear adial Length Wt. Connection Capacitor Product Model Speed ated W Hz V Ph Milli - atio Load mm (inch) kg (lbs.) Diagram Part No. Type Number (rpm) Torque (Milli-HP) Amps N (oz.) XH (not Nm (oz-in.) supplied) PEMANENT SPLIT CAPACITO (NOMAL SLIP), NON-SYNCHONOUS 7.67 (95) 2.8 (3.8) (20) 84.4 (3.3) 1.3 (2.9) KCI-26T (75) 2.8 (3.8) (20) 80.4 (3.2) 1.3 (2.9) KCI-26A (45) 2.8 (3.8) (20) 80.4 (3.2) 1.3 (2.9) KCI-26A (15) 2.8 (3.8) (20) 80.4 (3.2) 1.3 (2.9) KCI-26A XH 23.2 (0.91) 6.5 (0.26) 16.0 (0.63) 10 (.39) MIN (.17) Ø 13.5 (0.53) NOT MACHINED 61.0 (2.40) SQ. Ø 5 h6 (.20) 48.5 (1.91) 15.0 (0.59) 90 ±1 (4) M4x7-6G, on 68 mm bolt circle STANDAD LEADS / -25 (12+2 / -1) 8.4 (0.33) 84

5 AC INTENATIONAL PODUCTS 30-D GEAMOTO 24A 4.5 MOTO Nm (40 LB-IN.) MAXIMUM For more information see page 20 Output Input Gear adial Length Wt. Connection Capacitor Product Model Speed ated W (HP) Hz V Ph Amps atio Load mm (inch) kg (lbs.) Diagram Part No. Type Number 1 Nm (lb-in.) PEMANENT SPLIT CAPACITO (NOMAL SLIP), NON-SYNCHONOUS (40) 15 (1/48) (65) (5.2) 2.6 (5.9) BECI-D4 N (40) 18 (1/41) (65) (5.5) 2.8 (6.3) BECI-D (24) 18 (1/41) (65) (5.5) 2.8 (6.3) BECI-D (14) 18 (1/41) (65) (5.5) 2.8 (6.3) BECI-D3 N (9.7) 18 (1/41) (65) (5.5) 2.8 (6.3) BECI-D3 N (3.58) 67.3 Vent hole (2.65) SQ. EF (4) M5x.8-6H on a 95 mm bolt circle 34-Z GEAMOTO 11.3 NM (100 LB-IN.) MAXIMUM XH STANDAD LEADS /-25 (12+2/-1) 14.3 (0.56) Shown with standard terminal box 38.8 (1.53) 23.0 (0.9) For more For more information information see page see page?? 21 Output Input Gear adial Length Wt. Connection Capacitor Product Model Speed ated W (HP) Hz V Ph Amps atio Load mm (inch) kg (lbs.) Diagram Part No. Type Number 1 Nm (lb-in.) PEMANENT SPLIT CAPACITO, NON-SYNCHONOUS (100) 50 (1/15) (125) 217 (8.54) 4.5 (10.1) BFCI-Z4 N (100) 50 (1/15) (125) 217 (8.54) 4.5 (10.1) BFCI-Z (36) 50 (1/15) (100) 194 (7.64) 4.5 (10.1) BFCI-Z2 N (15) 50 (1/15) (100) 194 (7.64) 4.5 (10.1) BFCI-Z2 N1451 XH For optional terminal box model 1982, see page 100. Ø 11 h6 (0.43) 18.0 (0.7) 38.8 (1.53) (4.10) 14.3 (0.58) 1.5 (0.06) 18.0 (0.71) 4 SQ 4.1 (0.16X0.16) 18.8 (0.74) 86.6 (3.41) SQ. Ø 29.0 (1.14) NOT MACH (1.3) EF (4.02) 68.6 ±0.8 Vent hole (2.7 ±0.03) ( 4) M5x0.8-6H, 9.6 mm deep minimum on a 95 mm bolt circle Ø 11 h6 (0.43) 23.0±0.03 (0.9±0.001) 4 SQ. (0.16) 67.1 (2.64) MAX 53.1 (2.09) MAX 31.0 (1.22) S 86.4 (3.40) SQ. 28 (1.1) NOT. MACH (0.58) INTODUCTION INDEX INTENATIONAL BUSHLESS DC PEMANENT MAGNET DC INDUCTION AC 85

6 AC INTENATIONAL PODUCTS 34-W GEAMOTO Shown with standard terminal box 24A 19.8 MOTO Nm (175 LB-IN.) MAXIMUM NON-SYNCHONOUS For more For information more information see page see?? page 22 Output Input Gear adial Length Wt. Connection Capacitor Product Model Speed ated W (HP) Hz V Ph Amps atio Load mm (inch) kg (lbs.) Diagram Part No. Type Number Nm (lb-in.) PEMANENT SPLIT CAPACITO, NON-SYNCHONOUS (175) 75 (1/10) (130) 234 (9.20) 5.7 (12.8) BFCI-W (146) 75 (1/10) (130) 234 (9.20) 5.7 (12.8) BFCI-W (53) 75 (1/10) (65) 234 (9.20) 5.7 (12.8) BFCI-W (14) 75 (1/10) (65) 234 (9.20) 5.7 (12.8) BFCI-W (4.10) (4.02) XH 5.6 (0.22) Vent hole ( 4) M6x1-6H, 12.7 mm deep minimum on a 121 mm bolt circle 64.0 (2.52) 46.0 (1.81) 1.5 (.06) 30 (1.18) Ø 14 h6 (.55) 15.0 (0.59) 25.0 (.98) 1.02 (0.04) (0.03) 5 (.20)SQ (2.64) (2.09) 21.1 (0.83) (4.09) Ø 33.3 (1.31) 29.0 (1.14) 85.9 (3.38) Ø 86.1 (3.39) (4.08) SQ. 42-E GEAMOTO Shown with standard terminal box 24A 38.5 MOTO Nm (341 LB-IN.) MAXIMUM For more information see page 23 Output Input Gear adial Length Wt. Connection Capacitor Product Model Speed ated W (HP) Hz V Ph Amps atio Load mm (inch) kg (lbs.) Diagram Part No. Type Number Nm (lb-in.) THEE PHASE, NON-SYNCHONOUS (50) 140 (1/5) / / (300) 231 (9.08) 6.8 (15.3) BFPP-E PEMANENT SPLIT CAPACITO, NON-SYNCHONOUS (310) 100 (1/7.5) (200) 231 (9.08) 6.8 (15.3) BFCI-E (341) 100 (1/7.5) (200) 231 (9.08) 6.8 (15.3) BFCI-E (297) 100 (1/7.5) (200) 231 (9.08) 6.8 (15.3) BFCI-E (148) 100 (1/7.5) (300) 231 (9.08) 6.8 (15.3) BFCI-E (99) 100 (1/7.5) (300) 231 (9.08) 6.8 (15.3) BFCI-E (50) 100 (1/7.5) (300) 231 (9.08) 6.8 (15.3) BFCI-E (26) 100 (1/7.5) (300) 231 (9.08) 6.8 (15.3) BFCI-E SPLIT PHASE (WITH CENTIFUGAL SWITCH), NON-SYNCHONOUS For more information see page?? (148) 100 (1/7.5) (300) 231 (9.08) 6.8 (15.3) BFSI-E Vent hole ( 4) M-6x1-6H, 12.7 mm deep minimum on a 130 mm bolt circle XH 66.5 (2.62) 3.6 (0.14) (4.02)MAX Ø (4.75) 51.7 (2.04) 1.5 (0.06) 10.2 (0.4) 40.0 (1.57) Ø 19 h6 (0.75) 1.0 (0.04) 0.8 (0.03) 25.0 (0.98) 6 SQ. (0.24) 67.1 (2.64) MAX 53.1 (2.09) (4.53) (4.70) Ø 96.0 (3.78) 91.9 (3.62) Ø 39.1 (1.54) 31.8 (1.25) 22.9 (0.9) 86

7 AC INTENATIONAL PODUCTS 34-3F GEAMOTO Shown with standard terminal box 4.2 Nm (37 LB-IN.) MAXIMUM For more information see page 25 Output Input Gear adial Length Wt. Connection Capacitor Product Model Speed ated W (HP) Hz V Ph Amps atio Load mm (inch) kg (lbs.) Diagram Part No. Type Number 1 Nm (lb-in.) PEMANENT SPLIT CAPACITO, NON-SYNCHONOUS (37) 50 (1/15) (40) 221 (8.69) 4.5 (10.1) BFCI-3F (34) 50 (1/15) (40) 221 (8.69) 4.5 (10.1) BFCI-3F (30) 50 (1/15) (40) 221 (8.69) 4.5 (10.1) BFCI-3F (19) 50 (1/15) (5) 221 (8.69) 4.5 (10.1) BFCI-3F N1488 XH (4.02) Ø11 h6 (0.43) (4.10) 25.4 (1.0) 30.2 (1.19) 50.8 (2.0) (2.60) (2.14) ( 4) M6x1-6H, 11 mm deep minimum 34-5F GEAMOTO 40.6 (1.60) 39.4 (1.55) 27.4 (1.08) 33.0 (1.30) Shown with standard terminal box 25.4±.8 (1.0±0.03) 18 (0.71) 53.1 (2.09) MAX 4 (0.16) SQ (1.45) 1.5 (0.06) 8.1 Nm (72 LB-IN.) MAXIMUM For more information see page 26 Output Input Gear adial Length Wt. Connection Capacitor Product Model Speed ated W (HP) Hz V Ph Amps atio Load mm (inch) kg (lbs.) Diagram Part No. Type Number Nm (lb-in.) PEMANENTSPLIT CAPACITO, NON-SYNCHONOUS (72) 50 (1/15) (50) 232 (9.15) 5.6 (12.3) BFCI-5F (60) 50 (1/15) (50) 232 (9.15) 5.6 (12.3) BFCI-5F (39) 50 (1/15) (50) 232 (9.15) 5.6 (12.3) BFCI-5F (21) 50 (1/15) (30) 232 (9.15) 5.6 (12.3) BFCI-5F (4.02) XH 38.1 (1.5) EF (4.10) 76.2±0.25 (3.0±0.01) 53.1(2.09) 90.9 (3.58) 45.5 (1.79) 43.7 (1.72) 40.6 (1.6) EF. Oil level plug 15.1 (0.59) EF ±0.127 (1.67 ±0.005) 67.1 (2.64) 36.0 (1.42) 25.0 (0.98) 53.1 (2.09) 67.1(2.64) 5 (0.20)SQ. Ø 14 h6 (0.55) 4 HOLES 6.6 (0.26) 41.4 (1.63) 46.0 (1.81) 1.5 (0.06) 46.0 (1.81) 36.8 (1.45) (5.27) (4.45) 6.4 (0.25) EF. 82.6± 0.8 (3.25±0.03) 97.8 (3.85) INTODUCTION INDEX INTENATIONAL BUSHLESS DC PEMANENT MAGNET DC INDUCTION AC "C" standard location of breather hole 87

8 AC INTENATIONAL PODUCTS 42-5F GEAMOTO 10.5 Nm (93 LB-IN.) MAXIMUM Output Input Gear adial Length Wt. Connection Capacitor Product Model Speed ated W (HP) Hz V Ph Amps atio Load mm (inch) kg (lbs.) Diagram Part No. Type Number 1 Nm (lb-in.) PEMANENT SPLIT CAPACITO, NON-SYNCHONOUS (93) 83 (1/9) (80) 246 (9.69) 6.4 (14.3) BFCI-5F N (60) 83 (1/9) (80) 246 (9.69) 6.4 (14.3) BFCI-5F N (32) 83 (1/9) (10) 246 (9.69) 6.4 (14.3) BFCI-5F 1623 XH 53.3 (2.1) MAX Shown with standard terminal box 43.7 (1.72) 5 (0.20) SQ. 25 (0.98) 53.1(2.09) Ø 14 h6 (0.55) OIL LEVEL Ø HOLES [6.86 (0.27) I.D.] PLUG ( 4.75) 38.1(1.5) 41.4(1.63) (4.02) 76.2 (3.0) 82.6 (3.25) (3.58) 97.8 (3.85) (0.25) "C" standard location of breather hole 40.6 (1.60 ) EF. 42.4±0.127 (1.67±.005) 67.1 (2.64) 36.0 (1.41) 46.0 (1.81) 1.5 (0.06) 46.0 (1.81) (5.7) 42-5N GEAMOTO Shown with standard terminal box 12.8 NM (113 LB-IN.) MAXIMUM For more information see page 27 Output Input Gear adial Length Wt. Connection Capacitor Product Model Speed ated W (HP) Hz V Ph Amps atio Load mm (inch) kg (lbs.) Diagram Part No. Type Number Nm (lb-in.) THEE PHASE, NON-SYNCHONOUS (109) 140 (1/5) / / (180) 260 (10.25) 7.3 (16.3) BFPP-5N 1633 PEMANENT SPLIT CAPACITO, NON-SYNCHONOUS (113) 100 (1/7.5) (180) 260 (10.25) 7.3 (16.3) BFCI-5N (74) 100 (1/7.5) (180) 260 (10.25) 7.3 (16.3) BFCI-5N 1677 XH 53.1 (2.09) 43.7 (1.72) 5 (0.20)SQ (4.53) 46.0 (1.81) 46.0 (1.81) 53.1 (2.09) 30 (1.18) 67.1 (2.64) (5.71) (4.02) MAX Ø (4.75) 38.1 (1.50) (4) Ø 6.86 (0.27) 76.2 (3.0) 90.9 (3.58) Ø 14 h6 (0.55) 25 (.98) 36 (1.42) 45.5 (1.79) 40.6 (1.6) EF. 42.4±0.127(1.67±0.005) 6.4 (0.25) EF (1.63) EF (3.85) OIL LEVEL PLUG 82.6±0.8 (3.25±0.03) "C" standard location of breather hole 88

9 AC INTENATIONAL PODUCTS 42-GB GEAMOTO 42.9 Nm (380 LB-IN.) MAXIMUM For more information see page 28 Output Input Gear adial Length Wt. Connection Capacitor Product Model Speed ated W (HP) Hz V Ph Amps atio Load mm (inch) kg (lbs.) Diagram Part No. Type Number 1 Nm (lb-in.) PEMANENT SPLIT CAPACITO, NON-SYNCHONOUS 23 23(204) 100 (1/7.5) (200) 294 (11.57) 8 (17.5) BFCI-GB (290) 100 (1/7.5) (200) 294 (11.57) 8 (17.5) BFCI-GB N (375) 100 (1/7.5) (200) 294 (11.57) 8 (17.5) BFCI-GB N (380) 100 (1/7.5) (200) 294 (11.57) 8 (17.5) BFCI-GB (4.02) (4.75) DIA. XH (4) M6X1 6H 10 DEEP MIN. Shown with standard terminal box (4.98) 80.8 (3.18) 34.2 (1.34) 76.2 (3.0) (3) M8x1, 25-6H, 10 mm deep minimum on a 74 mm bolt circle "C" standard location of breather hole (1.34) 25 (0.98)EF (2.0) 54.6 (2.15) 19.1 (0.75) 53.1 (2.09) OIL LEVEL PLUG 67.1 (2.64) 6 (0.25) SQ. KEY 60.0 (2.36) 31.0 (1.22) 55.1 (2.17) OIL LEVEL PLUG 13.8(0.544) EF (5.10) Ø 19 h6 (0.75) 16.8 (0.66) 50.8 (2.00) 91.4 (3.60) INTODUCTION INDEX INTENATIONAL BUSHLESS DC PEMANENT MAGNET DC INDUCTION AC 89

10 DC INTENATIONAL PODUCTS DC CONNECTION DIAGAM BOWN BLUE GEEN-YELLOW T. + - MOTO INSULATION ATINGS The performance ratings are based on Class F insulation material (155 C total). Connect as shown for clockwise rotation while viewing output shaft. To reverse direction, transpose brown and blue leads. TOQUE CONVESION TABLE To convert from A to B multiply by entry intercept A B Nm N-cm kg-cm g-cm lb-in. oz-in. Nm , N-cm kg-cm , g-cm lb-in , oz-in HP = 746 W 1 inch = 25.4 mm 1 lb-in.-sec 2 = 7061 kg-mm 2 24A MOTO WATTS (1/53-1/23 HP) 180VDC, FF=1.6 Continuous Duty For more information see page 33 Speed ated ated W (HP) KT KE Winding Winding otor adial Length Wt. Product Model (rpm) Torque Amps (oz-in./a) (V/krpm) es. Ind. Inertia Load mm (inch) kg (lbs.) Type Number 1 Nm (oz-in.) ohms mh kg mm 2 N (lbs.) XH (12) (1/53) (25) 99.8 (3.93) 1.3 (2.8) 24A2BEPM (18) (1/35) (25) 119 (4.68) 1.5 (3.4) 24A4BEPM N (16) (1/23) (25) 119 (4.68) 1.5 (3.4) 24A4BEPM (3.60) 61.5 (2.42) SQ. XH EF (0.63) EF. 3.2 (0.13) Ø 26 h9 (1.02) DIA. Ø 7 h6 (0.28) 61.5 (2.42) O.D /-25 (24 +2/-1) STANDAD LEADS 21.0 (0.83) 51.0 (2.00) 49.0 (1.93) (4) slots 4.7 mm (0.186 in.) wide on a mm ( in.) bolt circle 90

11 DC INTENATIONAL PODUCTS 32A MOTO Shown with optional terminal box model 1984 (see page 100) WATTS (1/25-1/9 HP) 180VDC, FF=1.6 Continuous Duty For more information see page 34 Speed ated ated W (HP) KT KE Winding Winding otor adial Length Wt. Product Model (rpm) Torque Amps (oz-in./a) (V/krpm) es. Ind. Inertia Load mm (inch) kg (lbs.) Type Number Nm (oz-in.) (ohms) Mh kg mm 2 N (lbs.) XH (25) (1/25) (55) 133 (5.22) 2.8 (6.3) 32A3BEPM (42) (1/15) (55) 160 (6.28) 3.6 (8) 32A5BEPM (40) (1/9) (55) 160 (6.28) 3.6 (8) 32A5BEPM 4221 INTODUCTION XH 53.1 (2.09) (4.02) 86.6 (3.41) DIA (0.50) (4) m5 x 0.8-6H,6.4 mm (.25 in.) deep minimum on a 65 mm bolt circle Without terminal box a 24 in. (+2/-1 in.) cord is standard. 2.3 (0.09) 20 (0.79) 14 (0.55) 3 (0.12) SQ. Ø 9 h6 (0.35) 42A MOTO Shown with optional terminal box model 1984 (see page 100) (4.38) 67.1 (2.64) 50 h9 (1.97) 65.0 (2.56) 86.6 (3.41) (4.01) WATTS (1/6.7-1/4 HP) 180VDC, FF=1.6 Continuous Duty For more information see page 35 Speed ated ated W (HP) KT KE Winding Winding otor adial Length Wt. Product Model (rpm) Torque Amps (oz-in./a) (V/krpm) es. Ind. Inertia Load mm (inch) kg (lbs.) Type Number 1 Nm (oz-in.) ohms mh kg mm 2 N (lbs.) XH (95) (1/6.7) (90) 171 (6.72) 5.9 (13) 42A5BEPM (70) (1/5) (90) 171 (6.72) 5.9 (13) 42A5BEPM (120) (1/5) (90) 200 (7.87) 7.3 (16) 42A7BEPM N (90) (1/4) (90) 200 (7.87) 7.3 (16) 42A7BEPM N (4.26) DIA. 57.2± 0.25 (2.25±0.01) 73.2 (2.88) XH (4.02) 12.7 (0.50) 2.5 (0.10) 30 (1.18) 25 (0.98) Ø 14 h6 (0.55) 37.3 (1.47) 5 (0.20)SQ. 7.1 (0.28) EF (4.62) DIA (2.63) 44.5 (1.75) EF (2.64) 88.9 (3.50) (4.75) EF h9 (2.76) 53.1 (2.09) (4.77) 22.4 (0.88) INDEX INTENATIONAL BUSHLESS DC PEMANENT MAGNET DC INDUCTION AC (4) m6 x 1-6H, 7.6 mm (.30) deep minimum on 85mm bolt circle Without terminal box a 24 in. (+2/-1 in.) cord is standard. 91

12 DC INTENATIONAL PODUCTS 24A-D GEAMOTO 24A 4.5 MOTO Nm (40 LB-IN.) MAXIMUM 180VDC, FF=1.6 Continuous Duty For more information see page 36 Speed ated Peak W (HP) Gear Amps adial Length Wt. Product Model (rpm) Torque Torque atio Load mm (inch) kg (lbs.) Type Number 1 Nm (lb-in.) Nm (lb-in.) N (lbs.) XH (40) 6.2 (55) 14 (1/53) (65) 152 (5.97) 1.9 (4) 24A2BEPM-D5 N (40) 6.2 (55) 14 (1/53) (65) 152 (5.97) 1.9 (4) 24A2BEPM-D (40) 6.2 (55) 21 (1/35) (65) 171 (6.72) 2.0 (4.5) 24A4BEPM-D (23) 4.8 (42) 21 (1/35) (65) 171 (6.72) 2.0 (4.5) 24A4BEPM-D (9.2) 1.8 (16) 21 (1/35) (65) 171 (6.72) 2.0 (4.5) 24A4BEPM-D3 N (4.17) EF (3.60) XH 22.1 (0.87) EF. 38.8±.8 (1.53) 29.0 (1.14) DIA (0.56) 18 (0.71). 4 (0.16) SQ (0.58) EF (3.41) SQ. 2.3 (0.09) EF. Ø 11 h6 (0.43) 2.3 (0.09) EF (2.42) DIA. STD. LEADS /-25 (24+2/-1) 67.3±0.8 (2.65±0.03) TYP. Vent hole ( 4) 1M5x0.8-5H, 9.6 mm (.38 in.) deep minimum on a 95 mm bolt circle 24A-Z GEAMOTO 24A 11.3 MOTO Nm (100 LB-IN.) MAXIMUM 180VDC, FF=1.6 Continuous Duty For more information see page 37 Speed ated Peak W (HP) Gear Amps adial Length Wt. Product Model (rpm) Torque Torque atio Load mm (inch) kg (lbs.) Type Number 1 Nm (lb-in.) Nm (lb-in.) N (lbs.) XH (100) 13 (115) 21 (1/35) (125) 199 (7.82) 2.3 (5) 24A4BEPM-Z4 N (46) 13 (115) 21 (1/35) (125) 199 (7.82) 2.3 (5) 24A4BEPM-Z (23) 8.3 (75) 21 (1/35) (125) 199 (7.82) 2.3 (5) 24A4BEPM-Z3 N (5) 1.9 (17) 21 (1/35) (100) 176 (6.92) 2.3 (5) 24A4BEPM-Z2 N1157 XH 7.6 (0.30) 40 (1.57) 18 (0.71) 4(0.16)SQ (3.60) 86.6 (3.41) SQ (1.14) NOT. MACH (0.58) EF. Ø 11 h6 (0.43) 61.5 (2.42) DIA (1.33) EF. STD. LEADS /-25 (24"+2/-1) 67.3±0.8 (2.65±0.03) (4.17) EF. Vent hole (4) 1M5x0.8-6H, 9.6 mm (.38 in.) deep minimum on a 95 mm bolt circle 92

13 DC INTENATIONAL PODUCTS 32A-Z GEAMOTO 6.4 Nm (57 LB-IN.) MAXIMUM 180VDC, FF=1.6 Continuous Duty For more information see page 38 Speed ated Peak W (HP) Gear Amps adial Length Wt. Product Model (rpm) Torque Torque atio Load mm (inch) kg (lbs.) Type Number 1 Nm (lb-in.) Nm (lb-in.) N (lbs.) XH (57) 13 (115) 29 (1/25) (125) 201 (7.90) 3.9 (8.6) 32A3BEPM-Z (35) 8.0 (71) 29 (1/25) (125) 201 (7.90) 3.9 (8.6) 32A3BEPM-Z3 N (14) 3.2 (29) 29 (1/25) (100) 178 (7.00) 3.9 (8.6) 32A3BEPM-Z2 N (2.09) XH (4.02) 86.6 (3.41) DIA. 32A-W GEAMOTO 53.1 (2.09) Shown with optional terminal box model 1984 (see page 100) 7.6 (0.30) 38.8 (1.53) Ø 11 h6 (0.43) 4(0.16) SQ (2.64) 29.0 (1.14) NOT. MACH. 18 (0.71) (4.37) 67.3±0.76 (2.65±0.03) 102 (4.01) 86.6 (3.41) 33.8 (1.33) 14.7 (0.58) EF. Vent hole (4) M5x0.8-6H, 9.6 mm deep minimum on a 95 mm bolt circle Without terminal box a 24 in. (+2/-1 in.) cord is standard. Shown with optional terminal box model 1984 (see page 100) 24A 19.8 MOTO Nm (175 LB-IN.) MAXIMUM 180VDC, FF=1.6 Continuous Duty For more information see page 39 Speed ated Peak W (HP) Gear Amps adial Length Wt. Product Model (rpm) Torque Torque atio Load mm (inch) kg (lbs.) Type Number 1 Nm (lb-in.) Nm (lb-in.) N (lbs.) XH (175) 23.7 (210) 29 (1/25) (130) 197 (7.75) 4.5 (10) 32A3BEPM-W (147) 23.7 (210) 50 (1/15) (130) 224 (8.81) 5.4 (11.75) 32A5BEPM-W4 N (77) 14.8 (130) 50 (1/15) (130) 224 (8.81) 5.4 (11.75) 32A5BEPM-W (38) 7.2 (64) 50 (1/15) (65) 224 (8.81) 5.4 (11.75) 32A5BEPM-W2 N (28) 5.2 (47) 50 (1/15) (65) 224 (8.81) 5.4 (11.75) 32A5BEPM-W (10) 1.9 (17) 50 (1/15) (65) 224 (8.81) 5.4 (11.75) 32A5BEPM-W2 N4249 XH 46 (1.81) 67.1 (2.64) (4.02) EF (1.31) DIA (2.52) 15 (0.59) 5.6 (0.22) 29.0 (1.14) 30 (1.18) Ø 14 h6 (0.55) 25 (0.98) 5 (0.20) SQ (3.41) DIA (3.38 ) SQ (3.39) DIA. Vent hole ( 4) M6x1-6H, 12.7 mm deep minimum on a 121 mm bolt circle Without terminal box a 24 in. (+2/-1 in.) cord is standard (0.83) (4.08) SQ. INTODUCTION INDEX INTENATIONAL BUSHLESS DC PEMANENT MAGNET DC INDUCTION AC 93

14 DC INTENATIONAL PODUCTS 42A-E&F GEAMOTO 24A 35.0 MOTO Nm (310 LB-IN.) MAXIMUM 180VDC, FF=1.6 Continuous Duty For more information see page 40 Speed ated Peak W (HP) Gear Amps adial Length Wt. Product Model (rpm) Torque Torque atio Load mm (inch) kg (lbs.) Type Number 1 Nm (lb-in.) Nm (lb-in.) N (lbs.) XH (310) 53.7 (475) 112 (1/6.7) (200) 238 (9.37) 7.3 (16) 42A5BEPM-E (310) 53.7 (475) 141 (1/5) (200) 267 (10.5) 8.6 (19) 42A7BEPM-E3 N (240) 32 (282) 141 (1/5) (200) 267 (10.5) 8.6 (19) 42A7BEPM-E (120) 16 (141) 141 (1/5) (300) 267 (10.5) 8.6 (19) 42A7BEPM-E (60) 12.0 (106) 141 (1/5) (300) 267 (10.5) 8.6 (19) 42A7BEPM-E (68) 39.0 (345) 141 (1/5) (300) 267 (10.5) 8.6 (19) 42A7BEPM-F2 N (32) 8.2 (73) 141 (1/5) (300) 267 (10.5) 8.6 (19) 42A7BEPM-E XH 51(2.01) (4.02) 10.0 (0.39) EF (4.26) DIA. Shown with optional terminal box model 1984 (see page 100) 3.6 (0.14) 1.5(0.06) 66.5 (2.62) 40 (1.57) 25 (0.98) 31.8 (1.25) 6 (0.24) SQ. Ø 19 h6 (0.75) 92.0 (3.62) 39.1 (1.54)DIA (0.90) (4.70) 67.1 (2.64) 31.0 (1.22) 53.1 (2.09) 96.0 (3.78) DIA. Vent hole ( 4) M6x1-6H, 12.7 mm (0.5 in.) deep minimum on a 130 mm bolt circle Without terminal box a 24 in. (+2/-1 in.) cord is standard (4.65) 24A-3F GEAMOTO 1.8 Nm (16 LB-IN.) MAXIMUM 180VDC, FF=1.6 Continuous Duty For more information see page 41 Speed ated Peak W (HP) Gear Amps adial Length Wt. Product Model (rpm) Torque Torque atio Load mm (inch) kg (lbs.) Type Number 1 Nm (lb-in.) Nm (lb-in.) N (lbs.) XH (16) 5.2 (46) 21 (1/35) (40) 189 (7.4) 2.4 (5.3) 24A4BEPM-3F N (11.6) 4.6 (41) 21 (1/35) (40) 189 (7.4) 2.4 (5.3) 24A4BEPM-3F N (6.4) 3 (26) 21 (1/35) (40) 189 (7.4) 2.4 (5.3) 24A4BEPM-3F (3.0) EF. 41.1(1.62) 39.4 (1.55) 61.5 (2.42) DIA. XH /-25 (24 +2/-1) STANDAD LEADS (4) M6x1-6H 11 MIN (1.0) 50.8 (2.0) 65.0 (2.56) 27.4 (1.08) 33.0 (1.30) 91.4 (3.60) 24 (0.94) (1.45) (1.45) 18 (0.71) 4 (0.16) SQ. Ø 11 h6 (0.43) 30.2 (1.19) 42.9 (1.69) MAX 92.2 (3.63) 94

15 DC INTENATIONAL PODUCTS 32A-5F GEAMOTO 4.0 Nm (35 LB-IN.) MAXIMUM 180VDC, FF=1.6 Continuous Duty For more information see page 42 Speed ated Peak W (HP) Gear Amps adial Length Wt. Product Model (rpm) Torque Torque atio Load mm (inch) kg (lbs.) Type Number 1 Nm (lb-in.) Nm (lb-in.) N (lbs.) XH (35) 13.3 (118) 50 (1/15) (80) (263) 5.4 (12) 32A5BEPM-5F (28) 11.3(100) 50 (1/15) (80) (263) 5.4 (12) 32A5BEPM-5F N (16) 6.1 (54) 50 (1/15) (80) (263) 5.4 (12) 32A5BEPM-5F N (8.6) 3.2 (28) 50 (1/15) (80) (263) 5.4 (12) 32A5BEPM-5F N (3.41) DIA. XH (4.02) 42A-5N GEAMOTO Shown with optional terminal box model 1984 (see page 100) Shown with optional terminal box model 1984 (see page 100) 9.5 Nm (84 LB-IN.) MAXIMUM 180VDC, FF=1.6 Continuous Duty For more information see page 43 Speed ated Peak W (HP) Gear Amps adial Length Wt. Product Model (rpm) Torque Torque atio Load mm (inch) kg (lbs.) Type Number 1 Nm (lb-in.) Nm (lb-in.) N (lbs.) XH (84) 20.0 (177) 112 (1/6.7) (120) 263 (10.35) 7.6 (16.8) 42A5BEPM-5N N (70) 20.0 (177) 112 (1/6.7) (120) 263 (10.35) 7.6 (16.8) 42A5BEPM-5N (40) 13.2 (117) 112 (1/6.7) (120) 263 (10.35) 7.6 (16.8) 42A5BEPM-5N N4235 XH (4.02) 53.1 (2.09) 53.1 (2.09) (4.06) EF (1.5) 51.6(2.03) 51.6 (2.03) 43.7 (1.72) 76.2 (3.0) 90.9 (3.58) 5 (0.20) SQ (1.79) 43.7(1.72) 5 (0.20)SQ 40.6 (1.60) 46.0 (1.81) 67.1 (2.64) Ø (4.61) Ø 14 h6 (0.55) (4.26) DIA. 4 [6.81(.268)] I.D (4.42) EF (1.50) 41.4 (1.63) 6.4 (0.25) EF (3.0) 82.6 (3.25) 90.9(3.58) 97.8 (3.85) Vent hole Without terminal box a 24 in. (+2/-1 in.) cord is standard (1.67) 40.6 (1.60) 42.4 (1.67) 36.1 (1.42) 25.0 (0.98) 46.0 (1.81) 67.1 (2.64) (4.37) DIA. 36 (1.42) 25 (0.98) Ø 14 h6 (0.55) 4 HOLES 6.81 (.268) I.D (1.63) EF (4.01) 82.6±0.8 (3.25 ±0.03) 97.8 (3.85) 46.0 (1.81) (5.51) 46.0 (1.81) 129 (5.08) 6.4 (0.25) EF. Vent hole Without terminal box a 24 in. (+2/-1 in.) cord is standard. INTODUCTION INDEX INTENATIONAL BUSHLESS DC PEMANENT MAGNET DC INDUCTION AC 95

16 DC INTENATIONAL PODUCTS 42A-5H GEAMOTO Shown with optional terminal box model 1984 (see page 100) 14.2 Nm (126 LB-IN.) MAXIMUM 180VDC, FF=1.6 Continuous Duty For more information see page 44 Speed ated Peak W (HP) Gear Amps adial Length Wt. Product Model (rpm) Torque Torque atio Load mm (inch) kg (lbs.) Type Number 1 Nm (lb-in.) Nm (lb-in.) N (lbs.) XH (126) 38.4 (340) 141 (1/5) (150) 330 (13.0) 16 (35.5) 42A7BEPM-5H (81) 27.9 (247) 141 (1/5) (150) 330 (13.0) 16 (35.5) 42A7BEPM-5H N4296 XH (4.02) 53.1 (2.09) (4.76) EF (2.64) (4.26) DIA (2.53) 71.4 (2.81) 25.0 (0.98) 39.9 (1.57) 111 (4.37 ) DIA (5.55) EF. 6 (0.24)SQ.. 19 h6 (0.75) 54.1 (2.13) EF. 76.5/75.7 (3.01/2.98) 185 (7.28) (4) [10.3(0.41)] I.D. HOLES (5.63) 38.1 (1.50) EF 60.5 (2.38) EF. 98.6± 0.25 (3.88±0.01) 68.3 (2.69)EF ±0.5 (5.38±.0.02) (6.38) 11.2 (0.44) EF. Vent hole Without terminal box a 24 in. (+2/-1 in.) cord is standard. 42A-GB GEAMOTO 42.8 Nm (380 LB-IN.) MAXIMUM 180VDC, FF=1.6 Continuous Duty For more information see page 45 Speed ated Peak W (HP) Gear Amps adial Length Wt. Product Model (rpm) Torque Torque atio Load mm (inch) kg (lbs.) Type Number 1 Nm (lb-in.) Nm (lb-in.) N (lbs.) XH (380) 67.5 (600) 112 (1/6.7) (200) 297 (11.69) 8.8 (19.5) 42A5BEPM-GB N (380) 67.5 (600) 112 (1/6.7) (200) 297 (11.69) 8.8 (19.5) 42A5BEPM-GB (377) 67.5 (600) 112 (1/6.7) (200) 297 (11.69) 8.8 (19.5) 42A5BEPM-GB (277) 53.9 (478) 112 (1/6.7) (200) 297 (11.69) 8.8 (19.5) 42A5BEPM-GB 1360 XH /-25 (24+2/-1) (4.98) 80.8 (3.18) 34.2 (1.34) 34.2 (1.34) (4.26) DIA (0.75) 76.2 (3.00) (4) HOLES M6X1 6H 10 DEEP MIN Vent hole ( 3) M8x1, 25-6H, 10 mm deep minimum on 74 mm B.C. ef (2.0) 54.6 (2.15) Ø 19 h6 (0.75) 60 (2.38) 25 (0.98) 6 (0.24) SQ. KEY 16.8 (0.66) 31.0 (1.22) 50.8 (2.00) 55.1 (2.17) 13.8 (0.544) EF (4.85) OIL LEVEL PLUG 96

17 DC INTENATIONAL PODUCTS UPM UNFILTEED SC DC CONTOLS CHASSIS, BASIC SPEED CONTOL For more information see page 52 W (HP) Input Voltage Output Voltage Continuous Output Peak Output Current Form Weight Product Model ating (VAC) 50/60 Hz (VDC) Current (Amps) (Amps) Factor kg (lbs.) Type Number 248 (1/3) 115/ / (1.0) UPM-3318C (1/3) 115/ / (1.0) UPM-3318C 0866 DIMENSIONS 12.7 (.50) TYP. 2.3 (.09) EF. FPM UNFILTEED SC DC CONTOLS CHASSIS, BASIC SPEED CONTOL W (HP) Input Voltage Output Voltage Continuous Output Peak Output Current Form Weight Product Model ating (VAC) (VDC) Current (Amps) (Amps) Factor kg (lbs.) Type Number 177 (1/4) (8.0) FPM-1850C 1850 DIMENSIONS 92.5 (3.64) 63.5 (2.50) TYP. Model 0865 has 0.25" Q.C. tabs for connections. Model 0866 has a pluggable terminal block ±0.25 (4.654±.010) 63.5 (2.50) 27.7 (1.09) 2.4. (0.10.) (4 PL.) 6.4(.25) TYP (3.80) TYP (4.30) 2.38 (.094). SLOTS (6 PLACES) (6.02) 6.4 (0.25) (6.52) 38.1 (1.50) 31.8 (1.25) 24.1 (.95) TYP. CONNECTION DIAGAM wire and connector included with control Yellow (Pin 12) Orange (Pin 10) Blue (Pin 8) White (Pin 11) Black (Pin 7) 10k ohm Speed Potentiometer (included with control) Socket J1 To inhibit switch (optional) CONNECTION DIAGAM JP Line Hot (230VAC) PW. LMT. A1 L1 S3 S1 H1 A2 L2 S2 H2 Line Neutral (230VAC) Fuse * (supplied by user) Fuse (supplied by user) All wires external to control must be supplied by user * This fuse only should be used when L2 is not neutral (such as for 230 VAC operation in USA) FL ACC 16 MAX + MIN L N A1 A2 Optional Inhibit Switch (supplied by user) 10K Ω Speed Potentiometer (included with control) J2 EG. TOQ. MIN. DEC. ACC. TOQ DIP SWITCH SW Earth Ground PM Motor Armature } 115 VAC or 230 VAC Line Voltage Motor Armature FA EG C PENDING INTODUCTION INDEX INTENATIONAL BUSHLESS DC PEMANENT MAGNET DC INDUCTION AC 97

18 DC INTENATIONAL PODUCTS FPM UNFILTEED SC DC CONTOLS IP-40 BASIC SPEED CONTOL W (HP) Input Voltage Output Voltage Continuous Output Peak Output Current Form Weight Product Model ating (VAC) (VDC) Current (Amps) (Amps) Factor kg (lbs.) Type Number 177 (1/4) (8.0) FPM-1855E 1855 DIMENSIONS (6.16) EF. CONNECTION DIAGAM Shown with enclosure door removed (3.94) EF (8.44) EF ( 6.16) EF. LINE HOT LINE NEUTAL MOTO POSITIVE O NEGATIVE MOTO NEGATIVE O POSITIVE EATH GOUND Accepts.5 in. liquid tight fittings Note: All wires external to control must be supplied by user 98

19 DC INTENATIONAL PODUCTS SELECTION TABLE- UNFILTEED DC CONTOLS 230 VAC INPUT, SC DIVE FPM SYSTEM PEFOMANCE WHEN USING BODINE 180V PM MOTOS (180 VDC OUTPUT) Motor/Gearmotor Specifications Model Number Matching Control Model Numbers Encased Chassis Speed Cont. No Product Nameplate eference Accepts Quick Terminal ange Torque Accessory Type ating Page Optional Connect Block (rpm) Nm(lb-in.) Shaft W (HP) Interface Tabs MOTOS WITHOUT GEA EDUCES (0.75) A2BEPM 14 (1/53) (1.13) A4BEPM 21 (1/35) (1.56) A3BEPM 29 (1/25) (1.0) A4BEPM 32 (1/23) (2.6) A5BEPM 50 (1/15) (2.5) A5BEPM 82 (1/9) (5.9) A5BEPM 112 (1/6.7) (7.5) A7BEPM 141 (1/5) (4.4) A5BEPM 143 (1/5) (5.6) A7BEPM 185 (1/4) PAALLEL SHAFT GEAMOTOS (40) N A2BEPM-D5 14 (1/53) (40) A2BEPM-D4 14 (1/53) (100) N A4BEPM-Z4 21 (1/35) (46) A4BEPM-Z3 21 (1/35) (40) A4BEPM-D3 21 (1/35) (23) N A4BEPM-Z3 21 (1/35) (23) A4BEPM-D3 21 (1/35) (9.2) N A4BEPM-D3 21 (1/35) (5) N A4BEPM-Z2 21 (1/35) (175) A3BEPM-W4 29 (1/25) (57) A3BEPM-Z3 29 (1/25) (35) N A3BEPM-Z3 29 (1/25) (14) N A3BEPM-Z2 29 (1/25) (147) N A5BEPM-W4 50 (1/15) (77) A5BEPM-W3 50 (1/15) (38) N A5BEPM-W2 50 (1/15) (28) A5BEPM-W2 50 (1/15) (10) N A5BEPM-W2 50 (1/15) (310) A5BEPM-E4 112 (1/6.7) (310) N A7BEPM-E3 141 (1/5) (240) A7BEPM-E3 141 (1/5) (120) A7BEPM-E3 141 (1/5) (68) N A7BEPM-F2 141 (1/5) (60) A7BEPM-E2 141 (1/5) (32) A7BEPM-E1 141 (1/5) IGHT ANGLE GEAMOTOS (16) N A4BEPM-3F 21 (1/35) (11.6) N A4BEPM-3F 21 (1/35) (6.4) A4BEPM-3F 21 (1/35) (35) A5BEPM-5F 50 (1/15) (28) N A5BEPM-5F 50 (1/15) (16) N A5BEPM-5F 50 (1/15) (8.6) N A5BEPM-5F 50 (1/15) (380) N A5BEPM-GB 112 (1/6.7) (380) A5BEPM-GB 112 (1/6.7) (377) A5BEPM-GB 112 (1/6.7) (277) A5BEPM-GB 112 (1/6.7) (84) N A5BEPM-5N 112 (1/6.7) (70) A5BEPM-5N 112 (1/6.7) (40) N A5BEPM-5N 112 (1/6.7) (126) A7BEPM-5H 141 (1/5) (81) N A7BEPM-5H 141 (1/5) INTODUCTION INDEX INTENATIONAL BUSHLESS DC PEMANENT MAGNET DC INDUCTION AC 99

20 CONTOLS & ACCESSOIES FO INTENATIONAL PODUCTS A Ceiling Mount Sidewall Mount Base Mount Most parallel shaft stock gearmotors have a breather hole on top and require that the driveshaft remain at 12 o clock position with respect to the horizon. See Mounting positions on page 4. ITEMS FO TYPE FPM CONTOLS Item Model No. Accessory Description A Analog Interface Board for use with Control model 1850 Allows control to accept a variable voltage or current signal from user s host controller in order to automatically control motor speed. Inputs are optically isolated. Digital Interface Board for use with Control model Allows control to accept 8 parallel TTL signals from user s host controller in order to automatically control motor speed. Inputs are optically isolated. Electronic Direction & Braking Board for use with Control model Allows user to change motor direction and to dynamically brake motor to a quick stop. Inputs are not optically isolated. Local/emote Switch for use with Control model 1850 when used with Accessory Models 1888 and 1889.Allows user to switch between automatic and manual operation. Sealing Kit for use with model 1855 in order to upgrade from the standard IP-40 (NEMA 1) enclosure to IP 44 (NEMA 4). MOTO AND GEAMOTO L BACKETS Deflection Model No. Motor Type kg (lbs.) N (lbs.) 0990 Kit for 24A.45 (1) 111 (25) 1968 Kit for 32A,24A-D, 24A-Z, 32A-Z, 30-D.57 (1.3) 222 (50) 1970 Kit for 32A-W,34-W.8 (1.8) 556 (125) 1969 Kit for 42A-E,42A-F, 42-E 1.1 (2.4) 890 (200) None Kit for (1.3) 222 (50) None Kit for 34-Z.68 (1.5) 445 (100) A C B D OTHE MOTO AND GEAMOTO KITS Item Model No Description kgs. (lbs.) A 1971 Base Mounting Kit for Metric 3F Gearmotors 1.1 (1/2) B 0982 Steel Terminal Box Kit for 42 Motors and Gearmotors.9 (2) C 1982 Die cast terminal box kit for 30 motors and gearmotors.45 (1) D 1984 Die Cast Terminal Box Kit with terminal block for Metric 32A, 34, 42A, and 42, Motors and Gearmotors.45 (1) E 0991 Die Cast Base Kit for 42A Motors.1 (.3) F 0992 Adaptor Plate.45 (1) CAPACITOS See page 30 for oil and metalized mylar capacitors dimensions. E F 100