CRJ-100/200 TOWBAR Towbar Specifications, Usage, Preventive Maintenance, and Parts MANUAL (Includes Optional Hydraulic Lift and Soft Start)

Transcription

1 CRJ-00/200 TOWBAR Towbar Specifications, Usage, Preventive Maintenance, and Parts MANUAL (Includes Optional Hydraulic Lift and Soft Start) For ordering New Towbars or Replacement Parts Please Contact: Towbar Or Or service@hallindustries.com Hall Industries, Inc. 54 Mecklem Lane Ellwood City, PA 67 August 5, Revision 0 Manufacturing Solutions Since 966 Page

2 Update Manual 0. Index. Specifications Section Description Page One Specifications 2 Two Operating Procedures 3 Three Preventive Maintenance 4 Four Replacement Part Kits / Assemblies 5 Five Ordering Info 5 Six How to find the part you need 6 Seven Attachment List 6.. Physical Specifications Part Number Description Weight Length CRJ 00 Full Assembly (25 Height x 35 Wide) 20 lb 2 0 With Fixed Wheel Carriage & Standard Eye CRJ 00 HL SS Full Assembly (30 Height x 20 Wide) With Hydraulic Lift Wheel Carriage & Soft Start 235lb 2 0 CRJ 00 SS Full Assembly (30 Height x 20 Wide) 225 lb 2 0 With Fixed Wheel Carriage & Soft Start CRJ 00 HL Full Assembly (30 Height x 20 Wide) With Hydraulic Lift Wheel Carriage 225 lb 2 0 CRJ 00 5 Towbar Head 78 lb Warranty: All parts are guaranteed against defects for one year. If at any time this manual is not followed it will void the warranty (preventive maintenance logs are required for all warranty replacement parts). All replacement parts must be genuine Hall Industries parts..3. Updates: Our manuals are updated periodically please check for updates on our website prior to ordering. Manufacturing Solutions Since 966 Page 2

3 2. Operating Procedures NOTE: This must be done in accordance with the aircraft manual. 2.. Inspect the Towbar (Prior to hooking up the towbar to the tug visually inspect): 2... Check for a bent or damaged frame and for worn or missing parts Check tires for damage Check that you have the proper towbar. NOTE: DO NOT attempt to tow any aircraft with a damaged or improper towbar Responsibility Operator of the tug must understand that it is his/her responsibility to move the aircraft safely the entire time that they are connected to the plane. NOTE: No speeding during push and pull Hooking Up to the Plane ~ Checks: You are using the proper tug and towbar for the size aircraft being moved The towbar you are using is approximately level between the aircraft and the tug The eye end of the towbar must moves freely on the hitch mounted on the tug Attach the Towbar to the Aircraft First check that the towbar head pins are in the open position Line up towbar to nose pin of aircraft and close nose pins Install lock pins Attach the Towbar to the Tow Tractor Lift to the level of the push back s hitch Position the push back tractor and install the hitch pin Tow or push the aircraft only if the tow bars tires are not touching the ground Push the Aircraft Manufacturing Solutions Since 966 Page 3

4 NOTE: This must be done in accordance with the aircraft manual. Basic Rules: Prior to moving, make sure that full swivel release pins are released (if applicable). Also double check that all the tie downs and chocks are removed and aircraft brakes are released. NOTE: This must be done in accordance with the aircraft manual Tow Slow, max speed is a brisk walk (Approximately 5 MPH). This will help to minimize the chance of a jack knife Do not exceed Aircraft nose wheel angle of towing limits. If not marked or not known, do not exceed 30 from center. Be extra cautious on snow and ice If you are driving make sure that you have plenty of help; wing walkers are helpful Make sure the operator / driver has direct contact with the pilot at all times while moving the aircraft. NOTE: Thousand of dollars in damage can occur in a few seconds while towing. It is estimated that 90% of towing damage is due to operator negligence / error. Accidents can be fatal Disconnect the Towbar from the Tug 2.8. Disconnect the Towbar from the Aircraft Remove lock pins and slide pins into the open position. Carefully lower the tow bar to the ground (use hydraulic lift if installed), and then move push back tractor and towbar clear of the aircraft. 3. Preventive Maintenance NOTE: Hall Industries recommends using this maintenance procedure monthly (or as required in your airlines maintenance procedure if sooner). Replace worn or damaged parts as needed. 3.. Check the head retention pin and the soft start eye retaining bolts for wear. Manufacturing Solutions Since 966 Page 4

5 3.2. Check wheels and wheel carriage for bent, broken, or worn parts and security. Lubricate pivot points using Hall lubricant (Part number TB LUBE) Check head assembly for operation of latch mechanism; look for bending, security, etc. Lubricate pivot points using Hall lubricant (Part number TB LUBE) Inspect jaw assembly for worn or damaged parts and security Check latch mechanism to ensure proper travel back and forth. Lubricate pivot points Check tow eye and hardware (tug attachment) for condition and security Check main body tube for bending or cracking Clean, repaint, or touch up paint as required Inspect tags and labels if damaged or missing replace (see the drawings in the attachment section for labels and placements) If the towbar is equipped with a hydraulic lift, check the fluid reservoir (in the down / collapsed position). Add fluid if necessary (Part number TB LUBE L). 4. Replacement Parts, Kits, & Assemblies Part Number QTY (in Kit) Description 4.. CRJ 00 2 KIT SHEAR PIN KIT 5. Ordering Info 4... CRJ Shear Pin HRJ 45 2A 2 Locknut CRJ 7 E Head Bushing CRJ Adapter Bushing 5.. Accepted Payments Include (but not limited to): 5... Visa MasterCard American Express Company Check Wire Transfer Manufacturing Solutions Since 966 Page 5

6 5.2. Standard terms ~ NET 30 with approved credit 5.3. Minimum Orders ~ $ The Order Form is listed in the attachments of this document. 6. How to find the part you need 6.. What pushbar do I need? 6... Soft Start Eyelet or Standard Eyelet (user preference) 6.2. What wheel carriage do I need? Fixed or Hydraulic lift (user preference) 7. Attachment List 7.. CRJ 00 CRJ 00 & 200 Towbar Complete 7.2. CRJ 00 5 CRJ 00 & 200 Towbar Head Complete 7.3. HRJ 45 2 TE SS Towbar Tube with Soft Start Toweye Assembly 7.4. TB SS3.5 D8Q Repairable Soft Start Assembly 7.5. HRJ 45 2 TE Towbar Tube with Standard Toweye Assembly 7.6. CRJ 400 Fixed Wheel Carriage 7.7. REG LIFT Regional Towbar Lift ~ Hydraulic 3 ½ 7.8. HRJ ASY Handle Assembly 7.9. AV Drag Plate 3.5 Bolted 7.0. Soft Start Brochure 7.. Order Form 7.2. Other Products and Custom Design Services Manufacturing Solutions Since 966 Page 6

7 ISIONS 0 ORIGINAL 3/27/2002 BY CJS CHK WHEEL CARRIAGE LOCATION 2/28/2003 CJS 2 UP DRAWING 7/30/203 BJE DC NOTES:. FOR MORE INFORMATION SEE SUB ASSEMBLY DRAWINGS. 2. TAGS MUST BE INSTALLED " " ITEM QTY PART NUMBER CRJ 00 5 HEAD AND ADAPTER COMPLETE 2 HRJ 45 2 TE TOWBAR TUBE AND EYE 3 CRJ 400 FIXED WHEEL CARRIAGE 4 HRJ ASY HANDLE ASSEMBLY 2' " 29" WHEELSET PLACEMENT 6 4 " HANDLE PLACEMENT " 203 HALL INDUSTRIES, INC. ALL RIGHTS RESERVED. HALL INDUSTRIES, INC. PROPRIETARY RIGHTS ARE INCLUDED IN THE INFORMATION DISCLOSED HEREIN. RECIPIENT, BY ACCEPTING THIS DOCUMENT, AGREES THAT NEITHER THIS DOCUMENT NOR THE INFORMATION DISCLOSED HEREIN NOR ANY PART THEREOF SHALL BE REPRODUCED OR TRANSFERRED TO OTHER DOCUMENTS OR USED OR DISCLOSED TO OTHERS FOR MANUFACTURING OR FOR ANY OTHER PURPOSE EXCEPT AS SPECIFICALLY AUTHORIZED IN WRITING BY HALL INDUSTRIES, INC. SOLIDWORKS CRJ 00 & 200 CONFIGURATIONS WITH FIXED WHEELSET W/ HYDRAULIC WHEELSET STANDARD EYELET CRJ 00 CRJ 00 HL SOFT START EYELET CRJ 00 SS CRJ 00 HL SS UNLESS OTHERWISE SPECIFIED DIMENSIONS ARE IN INCHES 54 Mecklem ln Ellwood City, PA 67 TOLERANCES ANGLE.XX.XXX ± 0.5 ±.0 ±.005 PROJECT AV X<2"=± /32" X>2"=±/6" FILE NAME CRJ 00 TOWBAR COMPLETE THIRD ANGLE PROJECTION TOWBAR COMPLETE CHECK SIZE DWG/PART NO. DC 7/30/203 A CRJ 00 2 DRAWN BJE 7/30/203 SCALE : WEIGHT: LBS SHEET OF FOLDER AV0906 LAST SAVED: 8//203 PRINTED: 8/5/203 Hall Industries, Inc.

8 NOTES:. 9 ISIONS BY CHK CRJ 00 HEAD HEAD COMPLETE CRJ PLAQUE DO NOT TOW PLAQUE 3 CRJ G KIT GUARD KIT (INCLUDES BOTH SIDES) LANYARD NOT SHOWN BUT IS INCLUDED IN HEAD ASSEMBLY CRJ 7 E HEAD BUSHING TB TAG METAL HALL INDUSTRIES TAG 20 TB DRIVE RIVET 8 CRJ ADAPTER BUSHING CRJ 00 ADAPTER COMPLETE CRJ 00 & 200 ITEM QTY PART NUMBER 2 CRJ 7 3 NOSE PIN 2 2 CRJ 7 6 HEAD SPRING 3 CRJ 00 HEAD WELDMENT 4 2 CRJ 00 4 SLIDE BOLT 5 CRJ 00 ADAPTER WELDMENT 6 CRJ 00 2 SHEAR PIN 7 CRJ 00 4 SHOULDER BOLT 8 2 CRJ 700 QRP QUICK RELEASE PIN 9 CRJ G L CRJ GUARD, LEFT 0 CRJ G R CRJ GUARD, RIGHT 4 H508C0056ZP0000 HH BOLT /2" 3 x.75" LONG YZP GR HRJ ROLL PIN 3 2 HRJ RETAINER SCREW 4 2 HRJ ALUMINUM KNOB 5 2 HRJ HANDLE SLIDE BOLT PIN 6 HRJ 45 2A STOVER LOCKNUT 7 HRJ 45 5 WASHER FLAT 5/8" ZP SAE 8 5 TB 832 H7 NYLOC NUT /2" TB 9205 A MKM GREASE FITTING 20 8 WH ZP0000 WASHER /2" SAE YZP 203 HALL INDUSTRIES, INC. ALL RIGHTS RESERVED. HALL INDUSTRIES, INC. PROPRIETARY RIGHTS ARE INCLUDED IN THE INFORMATION DISCLOSED HEREIN. RECIPIENT, BY ACCEPTING THIS DOCUMENT, AGREES THAT NEITHER THIS DOCUMENT NOR THE INFORMATION DISCLOSED HEREIN NOR ANY PART THEREOF SHALL BE REPRODUCED OR TRANSFERRED TO OTHER DOCUMENTS OR USED OR DISCLOSED TO OTHERS FOR MANUFACTURING OR FOR ANY OTHER PURPOSE EXCEPT AS SPECIFICALLY AUTHORIZED IN WRITING BY HALL INDUSTRIES, INC. SOLIDWORKS CRJ 00 4 ASY SLIDE BOLT KIT 2 5 UNLESS OTHERWISE SPECIFIED DIMENSIONS ARE IN INCHES 54 Mecklem ln Ellwood City, PA 67 TOLERANCES ANGLE.XX.XXX Hall Industries, Inc. ± 0.5 ±.0 ±.005 PROJECT AV X<2"=± /32" X>2"=±/6" FILE NAME CRJ 00 5 HEAD AND ADAPTER COMPLETE THIRD ANGLE PROJECTION HEAD AND ADAPTER COMPLETE CHECK SIZE DWG/PART NO. DC 7/26/203 A CRJ DRAWN BJE 7/25/203 SCALE :6 WEIGHT: LBS SHEET OF FOLDER AV0906 LAST SAVED: 8//203 PRINTED: 8/5/203 4

9 NOTES:. ANTI SIEZE ALL THREADS & WIRE TIE BOLTS. 2. TAGS MUST BE INSTALLED. ISIONS ADD DECAL 8/5/203 BY BJE CHK DC REPAIRABLE SOFT START 2 LANYARD NOT SHOWN BUT IS INCLUDED HRJ FOR PIN ONLY ITEM QTY. PART NUMBER HRJ 45 2 SS 3.5" TUBE WITH TAG AND DECAL 2 TB SS3.5 D8Q SOFT START 3.5 INCH 203 HALL INDUSTRIES, INC. ALL RIGHTS RESERVED. HALL INDUSTRIES, INC. PROPRIETARY RIGHTS ARE INCLUDED IN THE INFORMATION DISCLOSED HEREIN. RECIPIENT, BY ACCEPTING THIS DOCUMENT, AGREES THAT NEITHER THIS DOCUMENT NOR THE INFORMATION DISCLOSED HEREIN NOR ANY PART THEREOF SHALL BE REPRODUCED OR TRANSFERRED TO OTHER DOCUMENTS OR USED OR DISCLOSED TO OTHERS FOR MANUFACTURING OR FOR ANY OTHER PURPOSE EXCEPT AS SPECIFICALLY AUTHORIZED IN WRITING BY HALL INDUSTRIES, INC. SOLIDWORKS UNLESS OTHERWISE SPECIFIED DIMENSIONS ARE IN INCHES 54 Mecklem ln Ellwood City, PA 67 TOLERANCES ANGLE.XX.XXX Hall Industries, Inc. ± 0.5 ±.0 ±.005 PROJECT AV X<2"=± /32" X>2"=±/6" FILE NAME HRJ 45 2 TE SS TUBE AND SOFT START TOWEYE THIRD ANGLE PROJECTION TUBE AND SOFT START TOWEYE CHECK SIZE DWG/PART NO. VTM 6/29/203 A HRJ 45 2 TE SS DRAWN BJE 6/29/203 SCALE :5 WEIGHT: LBS SHEET OF FOLDER TM LAST SAVED: 8/5/203 PRINTED: 8/5/203

10 NOTES:. USE ANTI SEIZE ON ALL THREADED HARDWARE. ISIONS BY CHK WHEN THE NUT (TB SS4 09) IS PROPERLY TIGHTENED HALL INDUSTRIES, INC. ALL RIGHTS RESERVED. HALL INDUSTRIES, INC. PROPRIETARY RIGHTS ARE INCLUDED IN THE INFORMATION DISCLOSED HEREIN. RECIPIENT, BY ACCEPTING THIS DOCUMENT, AGREES THAT NEITHER THIS DOCUMENT NOR THE INFORMATION DISCLOSED HEREIN NOR ANY PART THEREOF SHALL BE REPRODUCED OR TRANSFERRED TO OTHER DOCUMENTS OR USED OR DISCLOSED TO OTHERS FOR MANUFACTURING OR FOR ANY OTHER PURPOSE EXCEPT AS SPECIFICALLY AUTHORIZED IN WRITING BY HALL INDUSTRIES, INC. SOLIDWORKS 8 6 ITEM QTY PART NUMBER WASHER NORDLOCK 2 2 TB SS STOP 3 TB SS END GUIDE 4 TB SS END GUIDE NO HOLE 5 TB SS3.5 0 CUSHION 6 2 TB SS3.5 HH BOLT 3/8" 6 x 3/4" LG ZP GR5 DRILLED HEAD 7 TB SS4 05 TUBING 8 TB SS4 07 DOWEL PIN /4" DIA. x 2" LONG SS 9 TB SS4 09 NUT /4" 7 THREAD GR5 ZP 0 TB SS4 EYE & SHAFT UNLESS OTHERWISE SPECIFIED DIMENSIONS ARE IN INCHES 54 Mecklem ln Ellwood City, PA 67 TOLERANCES ANGLE.XX.XXX Hall Industries, Inc. ± 0.5 ±.0 ±.005 PROJECT AV ~ SS EYE D8Q, HRJ X<2"=± /32" X>2"=±/6" FOLDER / FILE NAME AV080/ TB SS3.5 D8Q SOFT START 3.5 INCH ~ FOR MANUAL THIRD ANGLE PROJECTION SOFT START 3.5 INCH CHECK SIZE DWG/PART NO. VTM 6/29/203 A TB SS3.5 D8Q 0 DRAWN BJE 06/29/203 SCALE :5 WEIGHT: 24.7 LBS SHEET OF LAST SAVED: 7/8/203 PRINTED: 7/8/203

11 NOTES:. TAGS MUST BE INSTALLED. TB 3.5 EYE KIT EYE BOLT KIT ISIONS ADD DECAL AND KIT CALLOUT BY CHK 8/5/203 BJE DC 4 2 STANDARD EYELET LANYARD NOT SHOWN BUT IS INCLUDED HRJ FOR PIN ONLY 203 HALL INDUSTRIES, INC. ALL RIGHTS RESERVED. HALL INDUSTRIES, INC. PROPRIETARY RIGHTS ARE INCLUDED IN THE INFORMATION DISCLOSED HEREIN. RECIPIENT, BY ACCEPTING THIS DOCUMENT, AGREES THAT NEITHER THIS DOCUMENT NOR THE INFORMATION DISCLOSED HEREIN NOR ANY PART THEREOF SHALL BE REPRODUCED OR TRANSFERRED TO OTHER DOCUMENTS OR USED OR DISCLOSED TO OTHERS FOR MANUFACTURING OR FOR ANY OTHER PURPOSE EXCEPT AS SPECIFICALLY AUTHORIZED IN WRITING BY HALL INDUSTRIES, INC. SOLIDWORKS ITEM QTY PART NUMBER HRJ SHOULDER BOLT 2 HRJ CURVED WASHER 3 HRJ " TUBE WITH TAG AND DECAL 4 HRJ EYEBOLT 5 WH00000SS0000 WASHER SS 6 CN08C0000SS0000 CASTLE NUT SS 7 CP SS0000 PIN COTTER UNLESS OTHERWISE SPECIFIED DIMENSIONS ARE IN INCHES 54 Mecklem ln Ellwood City, PA 67 TOLERANCES ANGLE.XX.XXX Hall Industries, Inc. ± 0.5 ±.0 ±.005 PROJECT AV X<2"=± /32" X>2"=±/6" FILE NAME HRJ 45 2 TE TOWBAR TUBE AND EYE THIRD ANGLE PROJECTION TOWBAR TUBE AND EYE CHECK SIZE DWG/PART NO. DC 7/5/203 A HRJ 45 2 TE DRAWN BJE 7/5/203 SCALE :5 WEIGHT: 9.3 LBS SHEET OF FOLDER AV0904 LAST SAVED: 8/5/203 PRINTED: 8/5/203

12 NOTES:. TAGS MUST BE INSTALLED. 5 3 ISIONS BY CHK HALL INDUSTRIES, INC. ALL RIGHTS RESERVED. HALL INDUSTRIES, INC. PROPRIETARY RIGHTS ARE INCLUDED IN THE INFORMATION DISCLOSED HEREIN. RECIPIENT, BY ACCEPTING THIS DOCUMENT, AGREES THAT NEITHER THIS DOCUMENT NOR THE INFORMATION DISCLOSED HEREIN NOR ANY PART THEREOF SHALL BE REPRODUCED OR TRANSFERRED TO OTHER DOCUMENTS OR USED OR DISCLOSED TO OTHERS FOR MANUFACTURING OR FOR ANY OTHER PURPOSE EXCEPT AS SPECIFICALLY AUTHORIZED IN WRITING BY HALL INDUSTRIES, INC. SOLIDWORKS 7 ITEM QTY PART NUMBER CRJ 400 WHEEL CARRIAGE WELDMENT 2 2 CRJ WHEEL WHEEL 3 2 HRJ CLAMP 4 4 TB DRIVE RIVET 5 4 TB CLAMP BOLT 6 4 TB CLAMP NUT 7 2 TB WASHER 8 2 TB PIN COTTER 9 TB TAG METAL HALL INDUSTRIES TAG UNLESS OTHERWISE SPECIFIED DIMENSIONS ARE IN INCHES 54 Mecklem ln Ellwood City, PA 67 TOLERANCES ANGLE.XX.XXX ± 0.5 ±.0 ±.005 PROJECT AV THIRD ANGLE PROJECTION FILE NAME CRJ 400 FIXED WHEEL CARRIAGE PROJECT ID AV000 FIXED WHEEL CARRIAGE CHECK SIZE DWG/PART NO. DC /20/20 DRAWN A CRJ BJE /20/20 SCALE :5 WEIGHT: LBS SHEET OF Hall Industries, Inc. LAST SAVED: 8/5/203 PRINTED: 8/5/203

13 ITEM QTY PART NUMBER LIFT PUMP MOUNTING BRACKET 2 LIFT 4 LOWER PIVOT SHAFT 3 LIFT 3 WHEEL ARM WELDMENT 4 LIFT 2R WHEEL ARM PIVOT SHAFT/ W 2 COLLARS 5 LIFT 6 WHEEL ARM PIVOT WELDMENT 6 2 LIFT 8 HEX SOCKET SHOULDER BOLT 7 2 TB FLAT WASHER ZP 9 4 LIFT FLAT WASHER SAE ZP 0 2 LIFT 2 COTTER PIN, PIVOT SHAFT LIFT 4 CLEVIS PIN 3 4 TB 874 HEX BOLT GR5 ZP 4 2 TB WHEEL 0" 5 2 TB FLAT WASHER USS ZP 6 4 TB COTTER PIN, AXLE 7 TB HYD CYLINDER W/QUICK DISC, CPLG 8 TB HYDRAULIC HOSE 9 TB HYDRAULIC PUMP ASSEMBLY 20 4 HRJ HANDLE/WHEEL ASSY CLAMP 2 8 TB HEX BOLT GR5 ZP 22 8 TB HEX NUT NYLOCK ZP 23 4 TB LOCK WASHER ZP 24 2 TB EXTENSION SPRING 25 TB TAG METAL IDENTIFICATION TAG (NOT SHOWN) 26 4 TB DRIVE RIVET FOR TAG (NOT SHOWN) 200 HALL INDUSTRIES, INC. ALL RIGHTS RESERVED. HALL INDUSTRIES, INC. PROPRIETARY RIGHTS ARE INCLUDED IN THE INFORMATION DISCLOSED HEREIN. RECIPIENT, BY ACCEPTING THIS DOCUMENT, AGREES THAT NEITHER THIS DOCUMENT NOR THE INFORMATION DISCLOSED HEREIN NOR ANY PART THEREOF SHALL BE REPRODUCED OR TRANSFERRED TO OTHER DOCUMENTS OR USED OR DISCLOSED TO OTHERS FOR MANUFACTURING OR FOR ANY OTHER PURPOSE EXCEPT AS SPECIFICALLY AUTHORIZED IN WRITING BY HALL INDUSTRIES, INC. SOLIDWORKS UNLESS OTHERWISE SPECIFIED DIMENSIONS ARE IN INCHES TOLERANCES ANGLE.XX.XXX ± 0.5 ±.0 ±.005 THIRD ANGLE PROJECTION PROJECT ID AV000 CHECK DC DRAWN BJE /20/200 /20/200 PROJECT 54 Mecklem ln Ellwood City, PA 67 Hall Industries, Inc. FILE NAME REG LIFT REGIONAL TOWBAR LIFT REGIONAL TOWBAR LIFT SIZE DWG/PART NO. A REG LIFT 0 SCALE : WEIGHT: 50 LBS SHEET OF LAST SAVED: 4/8/20 PRINTED: 7/8/203

14 ISIONS CLAMP ANGLE BY 2/7/202 BJE CHK VTM HALL INDUSTRIES, INC. ALL RIGHTS RESERVED. HALL INDUSTRIES, INC. PROPRIETARY RIGHTS ARE INCLUDED IN THE INFORMATION DISCLOSED HEREIN. RECIPIENT, BY ACCEPTING THIS DOCUMENT, AGREES THAT NEITHER THIS DOCUMENT NOR THE INFORMATION DISCLOSED HEREIN NOR ANY PART THEREOF SHALL BE REPRODUCED OR TRANSFERRED TO OTHER DOCUMENTS OR USED OR DISCLOSED TO OTHERS FOR MANUFACTURING OR FOR ANY OTHER PURPOSE EXCEPT AS SPECIFICALLY AUTHORIZED IN WRITING BY HALL INDUSTRIES, INC. SOLIDWORKS 3 4 ITEM QTY PART NUMBER HRJ HANDLE 2 4 TB CLAMP BOLT 3 2 HRJ CLAMP 4 4 TB CLAMP NUT UNLESS OTHERWISE SPECIFIED DIMENSIONS ARE IN INCHES 54 Mecklem ln Ellwood City, PA 67 TOLERANCES ANGLE.XX.XXX Hall Industries, Inc. ± 0.5 ±.0 ±.005 PROJECT AV THIRD ANGLE PROJECTION FILE NAME HRJ ASY HANDLE ASSEMBLY PROJECT ID AV000 HANDLE ASSEMBLY CHECK SIZE DWG/PART NO. DC /20/20 DRAWN BJE /20/20 A HRJ ASY SCALE :4 WEIGHT: 3.78 LBS SHEET OF LAST SAVED: 6/28/203 PRINTED: 7/8/203

15 NOTES:. USE WHEN FACTORY INSTALLED DRAG PLATES HAVE BEEN WORN DOWN. ISIONS BY CHK HALL INDUSTRIES, INC. ALL RIGHTS RESERVED. HALL INDUSTRIES, INC. PROPRIETARY RIGHTS ARE INCLUDED IN THE INFORMATION DISCLOSED HEREIN. RECIPIENT, BY ACCEPTING THIS DOCUMENT, AGREES THAT NEITHER THIS DOCUMENT NOR THE INFORMATION DISCLOSED HEREIN NOR ANY PART THEREOF SHALL BE REPRODUCED OR TRANSFERRED TO OTHER DOCUMENTS OR USED OR DISCLOSED TO OTHERS FOR MANUFACTURING OR FOR ANY OTHER PURPOSE EXCEPT AS SPECIFICALLY AUTHORIZED IN WRITING BY HALL INDUSTRIES, INC. SOLIDWORKS ITEM QTY PART NUMBER 2 TB CLAMP NUT 2 HRJ CLAMP 3 AV DRAG PLATE WELDMENT 4 2 TB CLAMP BOLT UNLESS OTHERWISE SPECIFIED DIMENSIONS ARE IN INCHES 54 Mecklem ln Ellwood City, PA 67 TOLERANCES ANGLE.XX.XXX Hall Industries, Inc. ± 0.5 ±.0 ±.005 PROJECT AV THIRD ANGLE PROJECTION FILE NAME AV TOWBAR DRAG PLATE 3.5 INCH BOLTED PROJECT ID AV009 TOWBAR DRAG PLATE 3.5 INCH BOLTED CHECK SIZE DWG/PART NO. BJE 6/27/202 DRAWN BJE 6/27/202 A AV SCALE :2 WEIGHT: 2.57 LBS SHEET OF LAST SAVED: 7/0/203 PRINTED: 7/8/203 0

16

17 Hall Industries Equipment Division ~ AIRLINE ORDERS FAX#: PHONE # : ORDER : TAKEN BY: TIME: AIRLINE CODE: PERSON CALLING: PHONE#: FAX: E MAIL ADDRESS: CUSTOMER P.O.# MASTER CARD# EXP. : CVC# SHIP : HOW TO SHIP: UPS: GRD RED OTHER FED EX: GRD O/N O/N P OTHER Acct. # TRUCKING COMPANY: HUB : EMPLOYEE # BILLING ADDRESS: SHIP TO ADDRESS: PART NUMBER: : QTY: PRICE: NOTES:

18 Other Products and Custom Design Services: Hall Industries provides a number of additional products beyond our towbar line. Some of the custom projects that we have done are shown below. We have our own engineering staff along with machine, fabrication, and GSE maintenance shops. We can design and build your ideas to increase safety, productivity, and profits Custom Towbar (Solve a Problem) <<This project involved designing and manufacturing a custom towbar to be used in the Nuclear Industry. This towbar shipped complete with custom shear pins calibrated to the application. IA-8980 Preconditioned Air Inlet (PCA) Adapters << Our PCA Inlet Adapters are part of our GSE product line. We inventory all of the parts and can ship usually the same day as ordered.>> Certified Transmission Lifting Bracket (Meet a Demand) A customer came to us with a lifting problem. They needed a tested and certified lifting bracket to prevent them from getting cited by OSHA. We designed, tested, and fabricated a solution. >> << Adapter 832 to Tronair Hydro Adapter Assembly>> Hall Industries offers adapters for nearly every towbar (even competitors) that allow you to use our towbar tubes / heads with your existing equipment. Besides the products listed above some of the other things that we sell include PCA ducting, Solid PBB tires, and baggage cart tires. Feel free to contact us about your GSE problems; after all we are The Problem Solvers. Manufacturing Solutions Since 966 Page