Annex to the Accreditation Certificate D PL according to DIN EN ISO/IEC 17025:2005

Transcription

1 Deutsche Akkreditierungsstelle GmbH Annex to the Accreditation Certificate D PL according to DIN EN ISO/IEC 17025:2005 Period of validity: to Holder of certificate: AUCOTEAM GmbH Storkower Straße 115 a, Berlin for its Prüflabor für klimatische, mechanische und korrosive Umweltbeanspruchungen Tests in the fields: environmental simulation tests in the fields of temperature, humidity, corrosion, vibration and mechanical shock, solar simulation as well as tests in their combinations on technical products; protection tests; glow wire test Abbreviations used: see last page The laboratory is permitted within the specified testing fields *, without being required to inform and obtain prior approval from DAkkS the free choice of standard or equivalent test methods. The listed test methods are exemplary. The laboratory maintains a current list of all test methods in a flexible scope of accreditation. This document is a translation. The definitive version is the original German annex to the accreditation certificate. 1/12

2 1 Tests at field climatic, corrosive and mechanic dynamical environmental testing 1.1 Climatic tests * Type of test Test parameters Test range Measurement uncertainty Typically test methods Cold Dry heat Temperature change, fast Temperature change, slow damp heat, constant damp heat, cyclic Compound test Temperature/Humidity Water condensation test Temperature Relative humidity Temperature change with determined speed 75 C to +25 C 1,0 K +25 C to+300 C +301 C to C 100 % r.h. 0,5 K 5,0 K 1,5 % r.h. 10 K/min 5 % DIN EN DIN EN DIN EN DIN EN DIN EN DIN EN DIN EN DIN EN ISO DIN EN ISO Low air pressure with and without temperature Pressure 120 mbar 4 % DIN EN DIN EN DIN EN Artificial weathering Exposure rate 0,76 W/(m 2 nm) by 340 nm; 45 W/m 2 by 290 to 400 nm DIN EN ISO DIN EN ISO DIN EN ISO Period of validity: to Translation 2/12

3 1.2 Mechanical dynamic tests * Type of test Test parameters Test range Measurement uncertainty Typically test methods Vibrations, sinusoidal vibrations, Broadband noise Shock Bump (even with temperatureand humidity superposition) Frequenz Hz 3 % DIN EN DIN EN Acceleration 0,1 to 800 m/s² 3,2 % DIN EN Sinusoidal (30 Hz to 3 KHz) DIN EN vibrations DIN EN Broadband 0,1 to 800 m/s² 9,0 % DIN EN noise (5 Hz to 30 Hz) DIN EN to 1000 m/s² 5,2 % DIN EN Acceleration DIN EN Shock 1000 to 8000 DIN EN ,0 % m/s² DIN EN Shock test Impact energy 0,5... 4,99 J 3,0 % 0,2... 0,49 J 10,0 % 5, ,0 J 5 % DIN EN DIN EN Free fall Topple and Toppling over Height of fall mm 2 mm DIN EN Corrosive tests* Type of test Test parameters Test range Measurement uncertainty Typically test methods Salt spray tests constant and cyclical Salt concentration 0,5 to 5,0 % NaCl 0,2 % Temperature 33 C to 37 C 0,5 K Condensation ever h 1 ml to 2 ml / 80 cm² 0,3 ml DIN EN DIN EN DIN EN ISO 9227 DIN EN Period of validity: to Translation 3/12

4 1.4 Standardized test methods DIN EN ISO DIN EN ISO DIN EN ISO DIN EN ISO DIN EN ISO DIN EN ISO DIN EN ISO DIN EN ISO DIN EN ISO DIN EN ISO Paints and varnishes Cruss cut test (withdrawn standard) Paints and varnishes Determination of film thickness (Modification: only determine the dry film thickness: Method 7C, Method 7D) Paints and varnishes Pull off test for adhesion Paints and varnishes Evaluation of degradation of coatings Designation of quantity and size of defects, and of intensity of uniform changes in appearance Part 2: Assessment of degree of blistering Paints and varnishes Evaluation of degradation of coatings Designation of quantity and size of defects, and of intensity of uniform changes in appearance Part 3: Assessment of degree of rusting Paints and varnishes Evaluation of degradation of coatings Designation of quantity and size of defects, and of intensity of uniform changes in appearance Part 4: Assessment of degree of cracking Paints and varnishes Evaluation of degradation of coatings Designation of quantity and size of defects, and of intensity of uniform changes in appearance Part 5: Assessment of degree of flaking Paints and varnishes Evaluation of degradation of coatings Designation of quantity and size of defects, and of intensity of uniform changes in appearance Part 6: Assessment of degree of chalking by tape method Paints and varnishes Evaluation of degradation of coatings Designation of quantity and size of defects, and of intensity of uniform changes in appearance Part 8: Assessment of degree of delamination and corrosion around a scribe or other artificial defect Plastics Methods of exposure to laboratory light sources Part 3: Fluorescent UV lamps Period of validity: to Translation 4/12

5 DIN EN ISO DIN EN ISO DIN EN ISO DIN EN ISO ISO ISO ISO ISO DIN EN DIN EN DIN EN DIN EN DIN EN Paints and varnishes Determination of resistance to humidity Part 1: Continuous condensation Paints and varnishes Determination of resistance to humidity Part 2: Procedure for exposing test specimens in condensationwater atmospheres Corrosion tests in artificial atmospheres Salt spray tests (Modification: only neutral salt spray test (NSS Test)) Paints and varnishes Exposure of coatings to artificial weathering Exposure to fluorescent UV lamps and water Road vehicles Environmental conditions and testing for electrical and electronic equipment Part 3: Mechanical loads (Modification: without point 4.5 Gravel Bombardement) Road vehicles Environmental conditions and testing for electrical and electronic equipment Part 4: Climatic loads (Modification: without point 5.9 Solar Radiation) Road vehicles Environmental conditions and testing for electrical and electronic equipment Part 5: Chemical loads Paints and varnishes Performance requirements for protective paint systems for offshore and related structures (Modification: without determination of resistance to cathodic disbanding according to ISO 15711) Degrees of protection provided by enclosures for electrical equipment against external mechanical impacts (IK code) (Modification: only IK06 to IK10) Railway applications Electronic equipment used on rolling stock (Modification: not a EMC Test) Electricity metering equipment (a.c.) Part 1: General requirements, tests and test conditions Metering equipment (class indexes A, B and C) Environmental testing Part 2 1: Tests Test A: Cold Environmental testing Part 2 2: Tests Test B: Dry heat Period of validity: to Translation 5/12

6 DIN EN DIN EN DIN EN DIN EN DIN EN DIN EN DIN EN DIN EN DIN EN DIN EN DIN EN DIN EN DIN EN DIN EN DIN EN Environmental testing Part 2 6: Tests Test Fc: Vibration (sinusoidal) Environmental testing Part 2: Tests Test Ka: Salt mist Environmental testing Part 2: Tests Test M: Low air pressure Environmental testing Part 2 14: Tests Test N: Change of temperature Environmental testing Part 2 27: Tests Test Ea and guidance: Shock Environmental testing Part 2 30: Tests Test Db: Damp heat, cyclic (12 h + 12 h cycle) Environmental testing Part 2 31: Tests Test Ec: Rough handling shocks, primarily for equipment type specimens Environmental testing Part 2 38: Tests Test Z/AD: Composite temperature/humidity cyclic test Environmental testing Part 2: Tests Test Z/AM: Combined cold/low air pressure tests Environmental testing Part 2: Tests Test Z/BM: Combined dry heat/low air pressure tests Environmental testing Part 2 47: Tests Mounting of specimens for vibration, impact and similar dynamic tests Environmental testing Part 2: Tests Test Kb: Salt mist, cyclic (sodium chloride solution) Environmental testing Part 2 53: Tests and guidance: Combined climatic (temperature/humidity) and dynamic (vibration/shock) tests Basic environmental testing procedures Part 2: Tests Test Ee and guidance: Bounce Environmental testing Part 2: Test methods Test Z/ABDM: Climatic sequence Period of validity: to Translation 6/12

7 DIN EN DIN EN DIN EN DIN EN DIN EN DIN EN DIN EN DIN EN VDE DIN EN DIN EN DIN EN DIN EN VDE Environmental testing Part 2 64: Tests Test Fh: Vibration, broadband random and guidance Environmental testing Part 2: Test methods Test Cx: Damp heat, steady state (unsaturated pressurized vapour) Environmental testing Part 2: Tests Test Cy: Damp heat, steady state, accelerated test primarily intended for components Environmental testing Part 2: Tests Test L: Dust and sand Environmental testing Part 2: Tests Test Eh: Hammer tests Environmental testing Part 2 77: Tests Test 77: Body strength and impact shock Environmental testing Part 2 78: Tests Test Cab: Damp heat, steady state Electrical relays Part 5: Insulation coordination for measuring relays and protection equipment Requirements and tests Electrical relays Part 21: Vibration, shock, bump and seismic tests on measuring relays and protection equipment Section 1: Vibration tests (sinusoidal) Electrical relays Part 21: Vibration, shock, bump and seismic tests on measuring relays and protection equipment Section 2: Shock and bump tests Electrical relays Part 21: Vibration, shock, bump and seismic tests on measuring relays and protection equipment Section 3: Seismic tests Measuring relays and protection equipment Part 27: Product safety requirements 9 Inscriptions, documentation and packaging Climatic environmental tests Mechanical tests) Period of validity: to Translation 7/12

8 DIN EN VDE DIN EN DIN EN DIN EN DIN EN Medical electrical equipment Part 1 11: General requirements for basic safety and essential performance Collateral standard: Requirements for medical electrical equipment and medical electrical systems used in the home healthcare environment 4.2 Environmental conditions 5 General requirements for the testing of ME devices 10.1 Additional requirements for mechanical strength) Fire hazard testing Part 2 11: Glowing/hot wire based test methods Glow wire flammability test method for end products Fire hazard testing Part 2 12: Glowing/hot wire based test methods Glow wire flammability index (GWFI) test method for materials Maritime navigation and radiocommunication equipment and systems General requirements Methods of testing and required test results 8.2 Dry heat 8.3 Damp heat 8.4 Cold 8.5 Heat shock (portable devices) Case on a solid surface 8.7 Vibration (all device classes) 8.8 Rain and spray (suspended appliances) 8.11 Resistance to oil (portable devices) 8.12 Corrosion (Salt spray) (all device classes) 12.1 Protection against accidental contact with hazardous voltages) Information technology equipment Safety Part 1: General requirements 4.2 Mechanical strength 6.5 Thermal requirements) Period of validity: to Translation 8/12

9 DIN EN DIN EN DIN EN DIN EN ASTM B ASTM D ASTM D RTCA / DO 160G Det Norske Veritas 2001 Safety requirements for electrical equipment for measurement, control and laboratory use Part 1: General requirements 5 Marking and documentation 8 Resistance to mechanical stresses 10 Equipment temperature limits and resistance to heat, except: Maintenance to air and creepage distances Insulation materials) Railway applications Rolling stock equipment Shock and vibration tests Electricity metering equipment (AC) General requirements, tests and test conditions Part 11: Metering equipment (Modification: all test methods, except: 7.4 Test for ground fault 7.5 Electromagnetic compatibility) High voltage switchgear and controlgear Part 203: Gasinsulated metal enclosed switchgear for rated voltages above 52 kv Point: Standard Practice for Operating Salt Spray (Fog) Apparatus Standard Test Methods for Vibration Testing of Shipping Containers (Modification: only method A1 (Vertical Motion)) Standard Test Methods for Random Vibration Testing of Shipping Containers Environmental conditions and test Procedures for airborne equipment Sec 4 Cold, dry heat, temperature changes, low pressure Sec 5 Temperature changes Sec 6 Damp heat Sec 7 Shock, constant acceleration Sec 8 Swing Sec 10 Condensation, splash Sec 14 Salt spray) Certification Notes No. 2.4 Environmental Test Specification for Instrumentation and Auto mation Equipment Point: 1 14 Period of validity: to Translation 9/12

10 Germanischer Lloyd 2012 Lloyds Register of Shipping 2002 MIL STD MIL STD 883H ISTA 1A 2001 ISTA 2A 2006 Guidelines on the implementation of Type test Part 1: Test requirements for electrical/electronic equipment, computers and peripherals 1 Visual test 2 Aptitude test 3 Power failure 4 Energy supply fluctuations (only for DC voltages) 5 Cold 6 Dry heat 7 Damp heat 8 Salt fog 9 Vibrations 10 Slopes 12 Pressure test 13 Insulation resistance 14 High voltage) Guidelines on the implementation of Type Tests, LR Type Approval System Test Specification Number Point: 1 14 Environmental Engineering considerations and laboratory tests Test method standard microcircuits 1001 Vacuum 1003 High dielectric strength, insulation resistance Damp heat, condensation Salt spray Temperature changes, slowly Temperature changes, fast Constant acceleration Swing Swing Swing 2026 Swing) Non Simulation Integrity Performance Test Procedure Packaged Products 150 lb (68 kg) or less Partial Simulation Performance Test Procedure Packaged Products 150 lb (68 kg) or less Period of validity: to Translation 10/12

11 MBN MBN MBN LV MBN LV VW JDQ 53.3 E/E Environmental Testing Part 1: Test Specifications Point 5 Environmental Testing Point 6 Environmental Test Specification (except: Solar Radiation Soak Mixed Flowing Gas) E/E Environmental Testing Part 2: Test Selection Process Electrical and electronic components in assenger vehicles up to 3,5 tonnes General requirements, test conditions and test methods Part 1: Electrical requirements (Modification: all test methods, except: Point 4 Electrical requirements and tests Point 9.17 Sunning Point 9.18 Sulfur dioxide test) Electrical and electronic components in assenger vehicles up to 3,5 tonnes General requirements, test conditions and test methods Part 2: Environmental requirements (Modification: all test methods, except: Point 4 Electrical requirements and tests Point 9.17 Sunning Point 9.18 Sulfur dioxide test) Electrical and electronic components in motor vehicles up to 3,5 tonnes General requirements, test conditions and test Environmental Design & Testing of Electronc/Electrical Components an Assemblies Point 3 Dust (except 3.3 Particle Impact) Point 4 Fluids Point 6 Mechanical (except Transit Shock) Point 7 Temperature / Humidity) Period of validity: to Translation 11/12

12 MAN M General requirements for electrical, electronic, mechatronic and mechanical systems Test plan for mechanical systems Functional test Qualification test (except: Noxious gas, EMV Dirt spraying chamber test Leak test Component specific test Xenon light fastness test Solar simulation system) 2 Protection tests and safety inspections DIN EN VDE 0470 Part ISO Degrees of protection provided by enclosures (IP code) Road vehicles Degrees of protection (IP code) Protection of electrical equipment against foreign objects, water and access abbreviations used: ASTM DIN EN ISO VDE RTCA MIL STD American Society for Testing and Materials German Institute for Standard European standard International Organisation for Standardisation Verband der Elektrotechnik Elektronik Informationstechnik e.v. (Association for Electrical, Electronic and Information Technologies) Radio technical commission for aeronautics Military standard of the US Army Period of validity: to Translation 12/12