Annex to the Accreditation Certificate D-PL according to DIN EN ISO/IEC 17025:2005

Transcription

1 Deutsche Akkreditierungsstelle GmbH Annex to the Accreditation Certificate D-PL according to DIN EN ISO/IEC 17025:2005 Period of validity: to Holder of certificate: Amphenol-Tuchel Electronics Gesellschaft mit beschränkter Haftung Prüflaboratorium August-Häusser-Straße 10, Heilbronn Tests in the fields: Electrical, mechanical and environmental simulation tests under inclusion of temperature, humidity, corrosion, IP degree of protection, vibration and mechanical shock as well as combinations thereof for the validation of connectors and other technical products Within the scope of accreditation marked with *), the testing laboratory is permitted, without being required to inform and obtain prior approval from DAkkS, to use standards or equivalent testing methods listed here with different issue dates. Within the given testing field marked with #), the testing laboratory is permitted, without being required to inform and obtain prior approval from DAkkS, the following: the free choice of standard or equivalent testing methods. The listed testing methods are exemplary. The testing laboratory maintains a current list of all testing methods within the flexible scope of accreditation. Connectors * DIN EN : and measurements - Part1-1: General examination; Test1a: Visual examination (IEC :2002 This document is a translation. The definitive version is the original German annex to the accreditation certificate. 1/7

2 Connectors * DIN EN : Connectors * DIN EN : Connectors * DIN EN : Connectors * DIN EN : Connectors * DIN EN : Connectors * DIN EN : Connectors * DIN EN : Connectors * DIN EN : Connectors * DIN EN : and measurements Part 2-1: Electrical continuity and contact resistance tests; Test 2a: Contact resistance; Millivolt level method (IEC :2002) Connectors for electronic equipment- Tests and measurements- Part 2-2: Electrical continuity and contact resistance tests Test 2b: Contact resistance - Specified test current method (IEC :2003) and measurements Part 2-6: Electrical continuity and contact resistance tests; Test 2f: Housing (shell) electrical continuity (IEC :2002) and measurements Part 3-1: Insulation tests; Test 3a: Insulation resistance (IEC :2002) and measurements Part 4-1: Voltage stress tests Test 4a: Voltage proof (IEC :2003) and measurements Part 5-1: Currentcarrying capacity tests; Test 5a: Temperature rise (IEC :2002); and measurements Part 5-2: Currentcarrying capacity tests; Test 5b: Currenttemperature derating (IEC :2002) and measurements Part 6-3: Dynamic stress tests; Test 6c: Shock (IEC :2002) and measurements Part 6-4: Dynamic stress tests; Test 6d: Vibration (sinusoidal) (IEC :2002) Period of validity: to Translation - 2/7

3 Connectors * DIN EN : Connectors * DIN EN : Connectors * DIN EN : Connectors * DIN EN : Connectors * DIN EN : Connectors * DIN EN : Connectors * DIN EN : Connectors * DIN EN : Connectors * DIN EN : and measurements Part 5-2: Currentcarrying capacity tests; Test 5b: Currenttemperature derating (IEC :2002) and measurements- Part 9-1: Endurance tests Test 9a: Mechanical operation (IEC :2010) and measurements Part 9-2: Endurance tests - Test 9b: Electrical load and temperature (IEC :2011) and measurements Part -5: Endurance tests Test 9e: Current loading, cyclic (IEC :2010) Connectors for electronic equipment- Tests and measurements Part 10-4: Impact tests (free components), static load tests and overload tests - endurance tests and overload tests Test 10d: Electrical overload (connectors) (IEC :2003); Electromechanical components for electronic equipment - Basic testing procedures and measuring methods Part 11: Climatic tests; Section 1: Test 11a: Climatic sequence (IEC :1995) and measurements Part 13-2: Mechanical operation tests Test 13b: Insertion and withdrawal forces (IEC :2006 and measurements Part 13-2: Mechanical operation tests Test 13b: Insertion and withdrawal forces (IEC :2006) and measurements Part 13-5: Mechanical operation tests Test 13e: Polarizing and keying method (IEC :2006) Low pressure tests exempted Period of validity: to Translation - 3/7

4 Connectors * DIN EN 61984: Connectors * DIN EN : Connectors * DIN EN 60529: Connectors- Safety requirements and tests (IEC 61984:2008) Solderless connections Part 2: Crimped connections - General requirements, test methods and practical guidance (IEC :2006) Degrees of protection provided by enclosures (IP Code) (IEC 60529: A1: A2:2013) Limited to: Protection against contact IP 1x up to IP4x Water tightness IPx7 and IPx8 Degree of protection * ISO 20653: Road vehicles - Degrees of protection (IP code) - Protection of electrical equipment against foreign objects, water and access Limited to: Protection against contact IP 1x up to IP4x Water tightness IPx7 and IPx8 Connectors Climatic Testing * VW 75174: Motor vehicle connectors Test specification 31 DIN EN DIN EN DIN EN DIN EN DIN EN DIN EN DIN Connectors Climatic Testing *# VW : Motor vehicle connectors - Slow-Motion Test Exempted Mixed flowing gastest ( MFG 4) Connectors Climatic Testing *# VW 60330: Crimped connections Solderless electrical connections Exempted DIN EN Period of validity: to Translation - 4/7

5 Corrosion*# 1: : : : : : : : : : : : DIN EN ISO 9227: testing Part 2-1: Tests Test A: Cold (IEC :2007) testing Part 2-2: Tests Test B: Dry heat (IEC :2007) testing- Part 2-6: Tests - Test Fc: Vibration (sinusoidal) (IEC :2007) testing Part 2: Tests; test Ka: Salt mist (IEC :1981) testing Part 2-14: Tests Test N: Change of temperature (IEC :2009) testing Part 2-27: Tests Test Ea and guidance: Shock (IEC :2008) testing Part 2-30: Tests Test Db: Damp heat, cyclic (12h + 12h cycle) (IEC :2005) testing Part 2-38: Tests Test Z/AD: Composite temperature/humidity cyclic test (IEC :2009) testing Part 2: Tests, Test Kb: Salt mist, cyclic (sodium chloride solution) (IEC :1996) testing; part 2: test methods; test Z/ABDM: climatic sequence (IEC :1991) testing Part 2-64: Tests Test Fh: Vibration, broadband random and guidance (IEC :2008); testing Part 2-78: Tests - Test Cab: Damp heat, steady state (IEC :2012) Corrosion tests in artificial atmospheres - Salt spray tests (ISO 9227:2012) Corrosion*# ASTM B 117:2011 Standard Practice for Operating Salt Spray (Fog) Apparatus Corrosion*# DIN EN ISO : Paints and varnishes - Determination of resistance to humidity Part 2: Procedure for exposing test specimens in condensation-water atmospheres (ISO :2005); Low pressure tests exempted Only NSS Only NSS Period of validity: to Translation - 5/7

6 Type of testing testing area / value range Measurement uncertainty limit deviation example standard Heat / Cold # -70 C up to +180 C - ±2 K 1 2 Temperature Change # -70 C up to +180 C - ±2 K 14 Nb Temperature Shock # 70 C up to +180 C - ±2 K 14 Na Temperature # 70 C up to +180 C ±0,25 K - - Humidity # 10 % up to 100 % RH ±3% RH 78 DIN EN ISO CHT Temperature Humidity cyclic # 10 % up to 100 % RH ±3% RH 38 DIN EN ISO AT / AHT Humidity # 95 % RH ±2% RH at 25 C up to 55 C - IPX7 / IPX8 Immersion test # at ambient temperature up to 25 m DIN EN ISO Pressure # up to 4 bar ±0,005 bar IP1X to IP4X Test probe # Test Force: ±10 % DIN EN ISO Vibration Sinusoidal / Frequency range # 5 Hz up to Hz Frequency: ±1 Hz from 5 Hz up to 50 Hz; ±2 % over 50 Hz Acceleration reference point: ±15 % 6 Random Vibration / Frequency range # 5 Hz up to Hz ±10 % grms 64 Period of validity: to Translation - 6/7

7 Type of testing testing area / value range Measurement uncertainty limit deviation example standard Mechanical Shock # Combined Vibration & Temperature # Acceleration: 5 g up to 50 g Shock duration: 2 ms up to 30 ms -50 C up to +150 C ±15 % m/s 27 ±2 K Frequency # 2 Hz up to Hz ±2 % Acceleration # 0,1 m/s² up to m/s² ±5 % Salt spray test # Condensation water atmosphere CH, AHT, AT # Ambient temperature (+5 K) up to +50 C Ambient temperature (+5 K) up to +42 C ±2 K DIN EN ISO ±3 K DIN EN ISO Visual inspection # Magnification ratio 8X up to 1000X Stereo DIN EN Contact interruption # 1 µs, 10 µs Time: ±10 % DIN EN Temperature rise # Current: 1 A up to 1000 A Temperature: 20 C up to 250 C Temperature: ±0,25 K Current: ±1 % DIN EN DIN EN DIN EN Force, pull and push # 1 N up to 100 kn ±0,5 % DIN EN DIN EN Heat / Cold # -70 C up to +180 C - ±2 K 1 2 Period of validity: to Translation - 7/7