NAPOLI WIRE PANELS. Epoxy-coated on galvanized core Ral 6005 green, Ral 9005 black or Ral 7016 anthracite Mesh 100 x 55 mm Wire Ø 3,8/4,0 mm. Art.

Transcription

1 Napoli wire panels

2 NAPOLI WIRE PANELS Epoxy-coated on galvanized core Ral 6005 green, Ral 9005 black or Ral 7016 anthracite Mesh 100 x 55 mm Wire Ø 3,8/4,0 mm mm Ø mm cm cm x 55 3,8/4, x 55 3,8/4, x 55 3,8/4, x 55 3,8/4, x 55 3,8/4, x 55 3,8/4, x 55 3,8/4, x 55 3,8/4, x 55 3,8/4, x 55 3,8/4, x 55 3,8/4, x 55 3,8/4, x 55 3,8/4, x 55 3,8/4, x 55 3,8/4, x 55 3,8/4, x 55 3,8/4, x 55 3,8/4, x 55 3,8/4, x 55 3,8/4, x 55 3,8/4,

3 PROFILE POST Profile post with cap Hot-dipped galvanized and then epoxy-coated Ral 6005 green, Ral 9005 black or Ral 7016 anthracite Zinc layer : g/m 2 Expoxy-coating: 54 µ Plastic collar available per piece Thickness: 1,4 mm Ø mm mm

4 HACCA POST Hacca post with cap Posts for wire panels to be erected simultaneously with concrete slabs. Ø mm mm , , , , , , , , , , , , , , , FLOORPIECE FOR HACCA POST mm

5 PLASTIC COLLAR SUITABLE FOR POST WITH PROFILE 1 2 Plastic 1: Corner bracket 2: End/middle bracket Type 1 2 Type mm Packaging per piece per piece per piece per 6 pieces per 6 pieces per 6 pieces per piece per piece per piece per 6 pieces per 6 pieces per 6 pieces BRACKETS SUITABLE FOR GATES Epoxy-coated Ral 6005 green, Ral 9005 black or Ral 7016 anthracite on galvanized steel Plastic Ral 6005 green, Ral 9005 black or Ral 7016 anthracite mm / / /

6 WALL FASTENING PANELS WALL FASTENING HINGES OF GATES FLOOR PIECE Green epoxy-coated, on galvanized steel Ral 6005 green, Ral 9005 black or Ral 7016 anthracite Packaging: per 4, including 8 plugs + 8 screws in plastic bag Ral alu floor piece for profile post and 48mm round post 48 and 60 mm Ral 6005 green, Ral 9005 black or Ral 7016 anthracite Ø mm LEGNO wooden slats for Napoli Natural screens cm set = 38 slats set = 38 slats set = 38 slats set = 38 slats

7 OMBRA Shade canopy Sight screen 95% sun and sight-blocking tarpaulin colour cm m % green % green 1, % green 1, % green 1, % green % black % black 1, % black 1, % black 1, % black % grey % grey 1, % grey 1, % grey 1, % grey CLIPS FOR OMBRA A To attach the shade canopies to wire panels or to Gardenplast B type A B

8 RIBBON Ribbon, including clips 1 Rol = 60 meter = ca 3m 2 50 mm, suitable for Giardino wire panels: Napoli and Milano. mm per rol per rol per rol CLIPS FOR RIBBON Clips for ribbon, for decorative applications mm

9 Check out the calculation tool for panel projects on our website

10 INSTRUCTIONS: PROFILE POST : PLACING IN THE GROUND 1. Purchasing tips Please note that the posts must be 50 cm above the height of the wire panels. There are end, middle and corner brackets. The number of brackets required depends on the height of the wire panels. The wire panels have a standard width of 200 cm; they can be shortened with a hacksaw. Finally, treat with rust-proof paint. Height of panel Length of post Bracket per post 63 cm 48 mm x 100 cm 2 83 cm 48 mm x 120 cm cm 48 mm x 150 cm cm 48 mm x 175 cm cm 48 mm x 200 cm cm 48 mm x 225 cm cm 48 mm x 250 cm 4 Example For a fence of 10 m length and 153 cm height you will need: 1 straight piece without corners, i.e.: 5 panels of 153 cm 6 posts of 48 mm x 200 cm 18 brackets 2. Preparation Align the fence and dig a hole every 2 metres to a depth of 60 cm and a diameter of 30 cm. 2 meter 2 meter 3. Erecting the first post/panel Fill the first hole with a light concrete mix or stabilizer, insert the post, determine the desired height and ensure that the post is straight. Attach the first panel to the posts with brackets (do not fully tighten the screws yet) and place some wooden blocks between the panel and the ground to level the panel.

11 INSTRUCTIONS: PROFILE POST : PLACING IN THE GROUND 4. Erecting the second post Place the second post against the first panel, determine the correct height and insert the post into the hole filled with a light concrete mix or stabilizer. Attach the second panel to the post with brackets (do not fully tighten the screws yet) and place some wooden blocks between the panel and the ground to level the panel. 5. Subsequent panels Proceed in the same way as above until you have erected all the panels and posts. 6. Adjustment Finish installing the fence by checking and adjusting the alignment. Finally, fill the holes with the concrete mix. 7. Finishing off Allow the concrete to dry for 48 hours, then fully tighten the bracket screws and remove the wooden blocks. Watch our instruction video

12 INSTALLATION TIPS FOR HACCA POST - INTO THE GROUND 1. Purchasing tips When buying, please note that the posts need to be approx. 50 cm longer than the height of the panels. The panels come in a standard width of 200 cm. They can be shortened using a hacksaw. Then, they need to be treated with a rustproof paint. Panel height Post length without concrete slab Post length with concrete slab 63 cm 103 cm 123 cm 83 cm 123 cm 153 cm 103 cm 153 cm 173 cm 123 cm 173 cm 203 cm 153 cm 203 cm 225 cm 173 cm 225 cm 260 cm 203 cm 260 cm 300 cm Example For example, for a fence of 10 metres in length, and 153 cm in height with a concrete slab, 1 straight piece without corners, you would typically need: 5 panels of 153 cm 6 posts of 225 cm 2. Preparation Trace out the fence and dig one hole to a depth of approx. 60 cm and a 30 cm diameter. 3. Placing the first post/panel Fill the first hole with light-weight concrete or stabilised sand, put in the post, determine the desired height and check that the post is level. Factor in the height of the post if you are using concrete slabs (approx. 30 to 40 cm longer). Attach the first panel.

13 INSTALLATION TIPS FOR HACCA POST - INTO THE GROUND 4. Placing the second post Place the second post up against the first panel and then dig the second hole. Determine the right height and secure the post into place with light-weight concrete or stabilised sand. 5. Subsequent panels Continue with this procedure until all the panels and posts are in place. 6. Making the final adjustments To finish the fence, check the alignment, adjust as necessary and fill the holes with concrete. 7. Finish Leave the concrete to dry for at least 48 hours.

14 INSTRUCTIONS: PROFILE POST : ON BRICK, CONCRETE OR ASPHALT 1. Purchasing tips Please note that the posts must be the same height as the wire panels. There are end, middle and corner brackets. The number of brackets required depends on the height of the wire panels. The wire panels have a standard width of 200 cm; they can be shortened with a hacksaw. Finally, treat with rust-proof paint. Height of panel Length of post Brackets per post 103 cm 48 mm x 100 cm cm 48 mm x 120 cm cm 48 mm x 150 cm cm 48 mm x 175 cm cm 48 mm x 200 cm 4 Example For a fence of 10 m length and 153 cm height you will need, 1 straight piece without corners, i.e.: 5 panels of 153 cm 6 posts of 48 mm x 160 cm 18 brackets 6 floor pieces 2. Preparation Align the fence and place the first foot piece, and continue, foot piece by foot piece, until the desired length has been reached. 2 meter 2 meter

15 INSTRUCTIONS: PROFILE POST : ON BRICK, CONCRETE OR ASPHALT 3. Erecting the first post / panel Place the post over the foot piece and ensure the post is level. Place the profile post over the top of the foot piece and tamp the post firmly (maintaining the vertical) until the bottom of the post touches the base of the foot piece. See instruction video on our website. Attach the first panel to the post with brackets (do not fully tighten the screws yet) and place some wooden blocks between the panel and the bricks, concrete or asphalt to level the panel. 4. Erecting the second post / panel Place the second post over the foot piece and ensure the post is straight. Place the profile post over the top of the foot piece and tamp the post firmly (maintaining the vertical) until the post is the same height as the panel already erected, or until the bottom of the post touches the base of the foot piece. Attach the second panel to the post with brackets (do not fully tighten the screws yet) and place some wooden blocks between the panel and the bricks, concrete or asphalt to level the panel. 5. Subsequent panels Proceed in the same way as above until you have erected all the panels and posts. 6. Adjustment Finish installing the fence by checking and adjusting the alignment. Finally, tighten the screws.

16 NAPOLI GATE Hot-dip galvanized then epoxy-coated Ral 6005 green, Ral 9005 black or Ral 7016 anthracite Frame four pipes of Ø 40 mm Provided with: Lock with handles + 2 unique keys, Adjustable hinges, Lock stop, Wire fence panel 100 x 55 x 4,0 mm 2 gate posts of Ø 60 mm, these are 50 cm longer than the height of the gate cm cm

17 NAPOLI GATE DOUBLE (2 x 200 cm) Hot-dip galvanized then epoxy-coated Ral 6005 green, Ral 9005 black or Ral 7016 anthracite Frame four pipes of Ø 40 mm Provided with: Lock with handles + 2 unique keys, Adjustable hinges, Lock stop, Wire fence panel 100 x 55 x 4,0 mm Hot-dip galvanized ground anchor and pin 2 square gate posts of 80 x 80 x 3 mm, these are 50 cm (by 100, 125 and 150 cm) and 60 cm (by 175 and 200 cm) longer than the height of the gate. cm cm x x x x x x x x x x x x x x x

18 NAPOLI GATE DOUBLE (2 x 150 cm) Hot-dip galvanized then epoxy-coated Ral 6005 green, Ral 9005 black or Ral 7016 anthracite Frame four pipes of Ø 40 mm Provided with: Lock with handles + 2 unique keys, Adjustable hinges, Lock stop, Wire fence panel 100 x 55 x 4,0 mm Hot-dip galvanized ground anchor and pin 2 square gate posts of 80 x 80 x 3 mm, these are 50 cm (by 100, 125 and 150 cm) and 60 cm (by 175 and 200 cm) longer than the height of the gate. cm cm x x x x x x x x x x x x x x x x

19 Check out the calculation tool for panel projects on our website.

20 Garden Trade International bvba Deense Wijersstraat 6 B-3740 Munsterbilzen tel. +32-(0) fax +32-(0) info@giardino-online.com F99997D v 2018/10 Printed on