Section 12. Contain-It Secondary Containment Piping System. Serviced by GF Little Rock

Transcription

1 Section 12 Contain-It Secondary Containment Piping System Serviced by GF Little Rock

2 Table of Contents Contain-It Pipe 12.4 Fittings 12.5 Terminations 12.7 Centralizers 12.8 Accessories 12.9 Adhesive Requirements 12.10

3 Glossary S = Contain-It Socket SPG = Spigot End (same dimension as pipe outside diameter) MPT = Male Pipe Thread FPT = Female Pipe Thread Product Line Description Discount 39 Fittings 41 Pipe 42 Accessories The technical information given in this publication implies no warranty of any kind and is subject to change without notice. Please consult our Terms and Conditions of Sale. Not for Use with Compressed Air or Gases DO NOT TEST with Air or Air over Water GF Piping DOES NOT RECOMMEND the use of thermoplastic piping products for systems to transport or store compressed air or gases, or the testing of thermoplastic piping systems with compressed air or gases in above or below ground locations. The use of GF Piping products in compressed air or gas systems automatically voids the warranty for such products, and their use against our recommendation is entirely the responsibility and liability of the installer. GF Piping will not accept responsibility for damage or impairment from its products, or other consequential or incidental damages caused by misapplication, incorrect assembly, and/or exposure to harmful substances or conditions. The only exception to this recommendation is when testing the Contain-It Secondary System or the Fuseal Squared Double Containment Piping System s containment joints.

4 Contain-It Pipe Secondary Containment Piping System Material: Clear PVC P/L: 41 Pipe Split Pipe - 10 foot lengths Plain Ends Inch Size Part Number List $/ft. Lift Qty (ft.) Minimum Order Qty (ft.) 4 * AA * AA Solid Pipe - 20 foot lengths Plain Ends Inch Size Part Number List $/ft. Lift Qty (ft.) Minimum Order Qty (ft) 4 * AB * AB ^ = 40% Restock Charge * = Non-Cancelable / Non-Returnable 12.4

5 Contain-It Fittings Secondary Containment Piping System Material: Clear PVC P/L: 39 Fittings Standard Pack Quantities; No Broken Packs Containment Coupling Standard, Split (SxS) Containment Coupling Extended, Split (SxS) E E Maximum Gap: 5.50 Containment Coupling Reducing, Split (SxS) 6x Containment 90 Ell, Split (SxS) Containment 45 Ell, Split (SxS) Containment Tee, Split (SxS) Containment Piping ^ = 40% Restock Charge * = Non-Cancelable / Non-Returnable 12.5

6 Containment 45 Wye, Split (S x S x S) Containment Cap, One Piece (S) Containment Female Adapter, One Piece (S x FPT) Plug, One Piece (MPT) Adapter Sleeve, One Piece (IPS Spg x S) 4x x Containment PPFR Floor Drain, One Piece (IPS Spg x MPT) 3x6 ^ x6 ^ For use with Fuseal Piping only ^ = 40% Restock Charge * = Non-Cancelable / Non-Returnable 12.6

7 Contain-It Terminations Secondary Containment Piping System Material: Clear PVC or Alcryn P/L: 39 Fittings Standard Pack Quantities; No Broken Packs Termination Fitting Rigid PVC, Split (Contain-It to IPS) 4x½ * x¾ * x1 * x1¼ * x1½ x x2½ * x x Test Termination Fitting Rigid PVC, Split (Contain-It to IPS) (with two 3/8 NPT Plugs) 4x T x T Termination Fitting Flexible Alcryn, One Piece (Contain-It to IPS/Metric) 4x½ or 20mm A x¾ or 25mm A x1 or 32mm A x1¼ or 40mm A x1½ or 50mm A x2 or 63mm A x2½ or 75mm A x3 or 90mm A x4 or 110mm A Alcryn is a registered trademark of Ferro Corporation. Test Termination Fitting Flexible Alcryn, One Piece (Contain-It to IPS/Metric) 4x½ or 20mm AT x¾ or 25mm AT x1 or 32mm AT x1¼ or 40mm AT x1½ or 50mm AT x2 or 63mm AT x2½ or 75mm AT x3 or 90mm AT x4 or 110mm AT Containment Piping 12.7

8 Contain-It Centralizers Secondary Containment Piping System Material: PVC P/L: 39 Fittings Standard Pack Quantities; No Broken Packs Custom Centralizers are available upon request Centralizer (Contain-It x IPS) 4x½ * x¾ * x1 * x1¼ * x1½ x x2½ * x x x½ Twin * x¾ Twin * x1 Twin * Centralizer (Contain-It x Copper) Inch Size Part Number List /ea. Std. Pack 4x½ * C x¾ * C x1 * C x1¼ * C x1½ * C x2 * C x2½ * C x3 * C x4 * C Centralizer (Contain-It x Metric) Inch Size Part Number List /ea. Std. Pack 4x20mm x25mm x32mm * x40mm x50mm x63mm * x75mm x90mm * x110mm * x20mm Twin * x25mm Twin * x32mm Twin *

9 Contain-It Accessories Secondary Containment Piping System P/L: 42 Accessories Standard Pack Quantities; No Broken Packs Fitting Clip (all fittings include the required number of clips for assembly) 4 & 6 * Pipe Clamp 4 & 6 * Drill Bits 4 * * K (6 kit contains one bit for injection holes and one bit for crossover holes) Manual Injection Gun - System II Part Number List $/ea. Std. Pack * Pneumatic Injection Gun - System II (includes regulator and gauge assembly) Part Number List $/ea. Std. Pack * Adhesive Cartridge - System II (limited self life of 18 months) Part Number List $/ea. Std. Pack * Containment Piping ^ = 40% Restock Charge * = Non-Cancelable / Non-Returnable Mixing Tip - System II Part Number List $/ea. Std. Pack Straight * Flexible * Bent *

10 Adhesive Requirements Contain-It Cartridge Fittings/Pipe # of Sockets/Tube 1 cartridge 4 fittings 14 1 cartridge 6 fittings 10 1 cartridge 4 pipe 20 ft. length, both sides 1 cartridge 6 pipe 10 ft. length, both sides Adhesive Cartridge Requirements Calculation This table is designed to assist in the accurate determination of the number of adhesive cartridges required for a specific project. Fittings Quantity of 4 Tees and Wyes Quantity of 4 Fittings (other than tees and wyes) x 3 = x 2 = /14 = Quantity of 6 Tees and Wyes x 3 = Quantity of 6 Fittings (other than tees and wyes) x 2 = /10 = (+) Split Pipe Feet 4 Split Pipe/20 (1 cartridge will fill 20 ft., both sides) = (+) Feet 6 Split Pipe/10 (1 cartridge will fill 10 ft., both sides) = (+) TOTAL CARTRIDGES 12.10