Pipe Nipples / Solvent Cement / Pipe Clips 11. Diaphragm Valves / Knife Gate Valves 21

Transcription

1

2 TABLE OF CONTENTS Pipe Sizing 1 Pipe 2 Tee s 3 Elbows 4 Couplings 5 Adaptors, Caps & Plugs 6 Unions 7 Reducer Bushing 8 Wye s / Clamp on Saddles 9 Flanges 10 Pipe Nipples / Solvent Cement / Pipe Clips 11 Gaskets 12 Pipe Tools 13 Ball Valves 14 3-Way Ball Valves 18 Butterfly Valves 19 Diaphragm Valves / Knife Gate Valves 21 Check Valves 22 Control Valves 23 In-line Strainers / Basket Strainers 24 Tank Adaptor / Expansion Joint / Schedule 40 Grey Fittings 25

3 PVC Pipe PVC or Polyvinyl Chloride is the most commonly used plastic material for manufacturing plastic pipe. It has a relatively high tensile strength and modulus of elasticity and, therefore, is stronger and more rigid than most other thermoplastics. Joining methods are by solvent cementing, threading (schedule 80 only) or flanging. PVC has been used successfully in such areas as chemical processing, industrial plating, water treatment, sewerage treatment and irrigation systems. Pressure ratings given are for solvent cemented systems. When adding valves, flanges, threads or other components, the system must be de-rated to the lowest component. Threaded fittings are rated at 50% of solvent cemented systems; flanges are rated to 150 psi (10 Bar), unions are rated at 235 psi (16 Bar). Pipe Sizing s of solvent cement jointed pipe & fittings, less than 8 NB commonly sold in Australia, are generally to one of the following standards AS 1477, ASTM D 1785, BS These systems have the concept of Nominal Bore NB, this is known as the imperial system to differentiate it from the metric system. In the imperial system the outside diameter is fixed & the wall thickness varies depending on the pressure rating of the pipe. Hence though a pipe may be sized as 2 NB, neither the inside or outside diameter need be exactly 2. In the true metric system the pipe is sized on the actual outside diameter, regardless of the pressure rating, so in the case of d63 pipe, measurement of the OD will be 63mm. It is vital to understand in most sizes, metric fittings will not fit imperial pipe & vise versa. In Australia, as a metric country using an imperial pipe system, it is common to specify pipe by the metric equivalent of the NB size. For example: 2 NB is sold as 50mm pipe but the actual OD is 60.3mm & the actual ID of Shed 80 is 48.5mm. In the metric system NB is denoted as DN & OD is denoted as d. This is the convention in this catalogue when using dimensions in mm. Dimensions in inches are nominal bore. The following table compares actual dimensions of the outside diameter of metric & imperial pipe, in most sizes the imperial systems are interchangeable. In most cases metric & imperial sizes are not interchangeable. Hence we offer a range of metric to imperial adaptors to interface the two systems. 1 ASTM D 1785 AS 1477 Grey Shed 80 White Class 18 BS4346 Metric System Inches MM N.B. D.N. O.D. O.D. O.D. d 1/ / / / /

4 PVC Pipe Features: Conforms to ASTM D-1785, Type 1, Grade 1 All PVC piping is produced from NSF approved compounds conforming to ASTM D-1784 Standard length 20 (6m) Handles temperatures up to 140 F (60 C) Not affected by soil in buried applications Contains UV stabilisers TiO₂ and Carbon Black Economical to install and maintain IPS-sized (inches) 1/8-24 Can be treaded (recommend schedule 80 or greater) Normally grey in colour Manufactured in the USA Schedule 80 Pipe Detail Schedule 40 Clear Pipe /2 PVC SCH80 PIPE 6 M / 20 FT 1/ /4 PVC SCH80 PIPE 6 M / 20 FT 3/ PVC SCH80 PIPE 6 M / 20 FT /4 PVC SCH80 PIPE 6 M / 20 FT 1-1/ /2 PVC SCH80 PIPE 6 M / 20 FT 1-1/ PVC SCH80 PIPE 6 M / 20 FT /2 PVC SCH80 PIPE 6 M / 20 FT 2-1/ PVC SCH80 PIPE 6 M / 20 FT PVC SCH80 PIPE 6 M / 20 FT PVC SCH80 PIPE 6 M / 20 FT PVC SCH80 PIPE 6 M / 20 FT PVC SCH80 PIPE 6 M / 20 FT PVC SCH80 PIPE 6 M / 20 FT 12 PL UVR-10 1/2 PVC CLEAR SCH40 PIPE 3 M / 10 FT 1/2 PL UVR-10 3/4 PVC CLEAR SCH40 PIPE 3 M / 10 FT 3/4 PL UVR-10 1 PVC CLEAR SCH40 PIPE 3 M / 10 FT 1 PL UVR /4 PVC CLEAR SCH40 PIPE 3 M / 10 FT 1-1/4 PL UVR /2 PVC CLEAR SCH40 PIPE 3 M / 10 FT 1-1/2 PL UVR-10 2 PVC CLEAR SCH40 PIPE 3 M / 10 FT 2 PL UVR /2 PVC CLEAR SCH40 PIPE 3 M / 10 FT 2-1/2 PL UVR-10 3 PVC CLEAR SCH40 PIPE 3 M / 10 FT 3 PL UVR-10 4 PVC CLEAR SCH40 PIPE 3 M / 10 FT 4 PL UVR-10 6 PVC CLEAR SCH40 PIPE 3 M / 10 FT 6 2

5 PVC Fittings Features: Type 1, Grade 1 (Cell Class B) meets ASTM D-1784 NSF approved for potable water Meets ASTM D-2464 (threaded fittings) Meets ASTM D-2467 (socket fittings) Grey in colour Manufactured in the USA Fittings carry a pressure rating different from pipe. Contact Allmach for specific pressure recommendations Schedule 80 Tee S ReinforcedTee SxSR FPT S FPT MPT SR SPIG / / / / / SR 1/ SR 3/ SR SR 1-1/ SR 2 Key to Abbreviations = Socket = Female Pipe Thread = Male Pipe Thread = Special Reinforced Thread = Spigot Reinforced Tee SR FPT Reducing Tee S SR 1/ SR 3/ SR SR 1-1/ SR /4 x 1/ x 1/ x 3/ /4X /2X3/ /2X /2X1-1/ X1/ X3/ X X1-1/ /2X /2X1-1/ /2X X X1-1/ X X2-1/ X X X X X X X8 3

6 PVC Fittings Schedule Elbow S / / / / / Elbow S / / / / / Sweep S 90 Reinforced Elbow SxSR FPT 90 Reinforced Elbow SR FPT S 1/ S 3/ S S 1-1/ S 1-1/ S SR 1/ SR 3/ SR SR 1-1/ SR 1-1/ SR SR SR SR 1/ SR 3/ SR SR 1-1/ SR 1-1/ SR 2 22-½ Elbow S Cross S / / / / / F F / / / / /

7 PVC Fittings Schedule 80 Coupling S Reinforced Coupling SR FPT / / / / / SR 1/ SR 3/ SR SR 1-1/ SR 1-1/ SR 2 Reducer Coupling SR FPT /4X1/ X1/ X3/ /4X1/ /4X3/ /4X /2X1/ /2X3/ /2X /2X1-1/ X1/ X3/ X X1-1/ X1-1/ /2X1-1/ /2X X X X X X6 Reinforced Reducer Coupling SR FPT SR 3/4X1/ SR 1X1/ SR 1X3/ SR 1-1/4X SR 1-1/2X3/ SR 1-1/2X SR 1-1/2X1-1/ SR 2X SR 2X1-1/2 Female Reinforced Adaptor SxSR FPT SR 1/ SR 3/ SR SR 1-1/ SR 1-1/ SR SR 2-1/ SR SR 4 5

8 PVC Fittings Schedule 80 Female Adaptor SR 1/2 SpigxSR FPT SR 3/ SR SR 1-1/ SR 1-1/ SR SR SR 4 Reinforced Reducing Female Adaptor SxSR FP Male Adaptor SxMPT SR 1/2X3/ SR 3/4X1/ SR 3/4X SR 1X1/ SR 1X3/ / / / / / Cap S Cap FPT Plug MPT / / / / / / / / / / / / / / Male Adaptor SpigxMPT / / / / Plug S / / / /

9 PVC Fittings Schedule 80 Union S (EPDM O-ring) / / / / / Reinforced Union SR FPT (EPDM O-ring) SR 1/ SR 3/ SR SR 1-1/ SR 1-1/ SR SR 2-1/ SR SR 4 Union S (FKM O-ring) / / / / / Reinforced Union SR FPT (FPM O-ring) SR 1/ SR 3/ SR SR 1-1/ SR 1-1/ SR SR 2-1/ SR SR 4 Reinforced Union SxSR FPT (EPDM) SR 1/ SR 3/ SR SR 1-1/ SR 1-1/ SR SR 2-1/ SR SR 4 Reinforced Union SxSR FPT (FKM) SR 1/ SR 3/ SR SR 1-1/ SR 1-1/ SR SR 2-1/ SR SR 4 S FPT MPT SR SPIG Key to Abbreviations = Socket = Female Pipe Thread = Male Pipe Thread = Special Reinforced Thread = Spigot

10 PVC Fittings Schedule 80 Reducer Bushing SxSPIG /2X1/ /2X3/ /4X1/ X3/ X1/ X3/ /4X1/ /4X3/ /4X /2X1/ /2X3/ /2X /2X1-1/ X1/ X3/ X X1-1/ X1-1/ /2X1/ /2X3/ /2X /2X1-1/ /2X1-1/ /2X X1/ X3/ X X1-1/ X1-1/ X X2-1/ X X X2-1/ X X X X X X X X X X X X10 Reducer Bushing SPIGxFPT /2X1/ /2X3/ /4X1/ X1/ X3/ /4X3/ /4X /2X1/ /2X3/ /2X /2X1-1/ X1/ X3/ X X1-1/ X1-1/ /2X X X2-1/ X X3 8

11 PVC Fittings Schedule 80 Reducer Bushing MPTxFPT /2X1/ /2X3/ /4X1/ X1/ X3/ /4X3/ /4X /2X1/ /2X3/ /2X /2X1-1/ X1/ X3/ X X1-1/ X1-1/ /2X X X2 Clamp-On Saddle w/fkm Stainless Steel Hardware Socket Outlet 866SV-247 2X1/2 866SV-248 2X3/4 866SV-249 2X1 866SV-250 2X1-1/4 866SV-251 2X1-1/2 866SV /2X1-1/2 866SV-335 3X1 866SV-338 3X2 866SV-417 4X1 866SV-420 4X2 866SV-422 4X3 866SV-528 6X2 866SV-530 6X3 866SV-532 6X4 866SV-578 8X2 866SV-582 8X4 866SV-585 8X6 866SV X4 866SV X6 866SV X4 866SV X6 Wye S / / / / / Key to Abbreviations S = Socket FPT = Female Pipe Thread MPT = Male Pipe Thread SR = Special Reinforced Thread SPIG = Spigot 9

12 PVC Fittings Schedule 80 Flanges N.B ANSI TABLE D TABLE E DIN # Holes PCD # Holes PCD # Holes PCD # Holes PCD 1/2" 4 x x x x /4" 4 x x x x " 4 x x x x /4" 4 x x x x /2" 4 x x x x " 4 x x x x /2" 4 x x x x " 4 x x x x " 4 x x x x " 8 x x x x " 8 x x x x " 12 x x x x " 12 x x x x Hole sizes and PCD are in mm PCD = Pitch Circle Diameter Flange Vanstone Style Multi-drill, T/D, DIN SOC / / / /2 M DE 3"/80 nom DIN 3"/80 nom DE 4"/110 nom DIN 4"/110 nom. M M Flange Suitability THROUGH TO are ANSI bolt pattern is suitable for ANSI & Table DE. M is suitable for ANSI & Table DE DE is suitable for Table DE only DIN is suitable for DIN only DE is suitable for Table DE only DIN is suitable for DIN only M is suitable for ANSI & Table DE M is suitable for ANSI & Table DE *Blind Flange / /4 S / /2 M DE DIN DE DIN 4 M M

13 PVC Fittings Schedule 80 Pipe Nipples BSPT x BSPT Pipe (In.) Nipple Length (Inches) 1-1/ Code ½ 882 ¾ / / For Toe Nipples add a 1 to the start of the part number. Example Pipe Clips Pipe Spacers Pipe Clip Type 061H PP BS/ASTM ½ ¾ ¼ ½ ½ Pipe Spacer ½ ¾ ¼ ½ ½ Solvent Cement Weld-On Low VOC Solvent Cement & Primers 11 IPS 705C-32 IPS 705C-16 IPS IPS IPS P70C-32 IPS P70C-16 1 ltr ½ ltr 1 ltr ½ ltr 1 ltr ½ ltr Estimated Joints per Quart Average of Joints per Quart of Weld-On Solvent Cement Pipe (in.) ½ ¾ 1 1½ of Joints These figures are estimated based on laboratory tests. Due to many variables in the field, these figures should be used as a guide only. *Primer note double the number of joints shown to get primer numbers.

14 Piping Accessories Chemical Gaskets ANSI 150 EPDM GASK-005E-ANSI 1/2 GASK-007E-ANSI 3/4 GASK-010E-ANSI 1 GASK-012E-ANSI 1-1/4 GASK-015E-ANSI 1-1/2 GASK-020E-ANSI 2 GASK-025E-ANSI 2-1/2 GASK-030E-ANSI 3 GASK-040E-ANSI 4 GASK-060E-ANSI 6 GASK-080E-ANSI 8 GASK-100E-ANSI 10 GASK-120E-ANSI 12 FKM GASK-005F-ANSI 1/2 GASK-007F-ANSI 3/4 GASK-010F-ANSI 1 GASK-012F-ANSI 1-1/4 GASK-015F-ANSI 1-1/2 GASK-020F-ANSI 2 GASK-025F-ANSI 2-1/2 GASK-030F-ANSI 3 GASK-040F-ANSI 4 GASK-060F-ANSI 6 GASK-080F-ANSI 8 GASK-100F-ANSI 10 GASK-120F-ANSI 12 Table D/E EPDM GASK-005E-DE 1/2 GASK-007E-DE 3/4 GASK-010E-DE 1 GASK-012E-DE 1-1/4 GASK-015E-DE 1-1/2 GASK-020E-DE 2 GASK-025E-DE 2-1/2 GASK-030E-DE 3 GASK-040E-DE 4 GASK-060E-DE 6 GASK-080E-DE 8 GASK-100E-DE 10 GASK-120E-DE 12 FKM GASK-005F-DE 1/2 GASK-007F-DE 3/4 GASK-010F-DE 1 GASK-012F-DE 1-1/4 GASK-015F-DE 1-1/2 GASK-020F-DE 2 GASK-025F-DE 2-1/2 GASK-030F-DE 3 GASK-040F-DE 4 GASK-060F-DE 6 GASK-080F-DE 8 GASK-100F-DE 10 GASK-120F-DE 12 Features 12

15 Piping Accessories Pipe Cutting Tools Ratchet Shears 7290 Replacement Blade 7300 Quick Release Wheel Cutters TC2QPVC ½-2 TC5QPVC 2-4 TC6QPVC 3-6 TC8Q680PVC 6-8 Pipe Bevellers Deburring Tool BT1 1½-8 BT2 1½-12 (in) DEB2 Up to 2 13

16 Valves & Actuation Georg Fischer Ball Valves EPDM O-ring FKM O-ring Ends PVC ½ S/T ¾ S/T S/T ¼ S/T ½ S/T S/T ½ S S S Type 546 Ball Valve with Lockable Handle EPDM O-ring FKM O-ring Ends PVC ½ S/T ¾ S/T S/T ¼ S/T ½ S/T S/T

17 Valves & Actuation Georg Fischer Actuated Ball Valves Type 133 Electrically Actuated EPDM O-ring FKM O-ring Type 133 PVC Socket/Threaded Ends ½ ¾ ¼ ½ Type 233 Pneumatically Actuated EPDM O-ring FKM O-ring Type 233 PVC Without Manual Override ½ ¾ ¼ ½ EPDM O-ring FKM O-ring Type 233 PVC With Manual Override ½ ¾ ¼ ½

18 Valves & Actuation Spears Ball Valves Spears 2000 Industrial Ball Valve EPDM O-ring FKM O-ring PVC Socket & Thread (*Socket only) ½ ¾ ¼ ½ * * * * Spears 2000 Standard Ball Valve EPDM O-ring List Price PVC Socket & Thread (*Socket only) ½ ¾ ¼ ½ * * * * FKM O-ring 16

19 Valves & Actuation Sanking Ball Valves Sanking True Union Ball Valve Features: NSF listed & materials meet drinking water standard Smooth opening & closing thanks to a lower torque 100% pure virgin material, CaCO3 free (Chalk) UV resistant powder added 100% pressure testing before leaving the factory Can be assembled with Pneumatic/Electric Actuators EPDM O-ring FKM O-ring List Price PVC Socket & Thread (*Socket only) ½ TUBV-005E TUBV-005V ¾ TUBV-007E TUBV-007V 1 TUBV-010E TUBV-010V 1¼ TUBV-012E TUBV-012V 1½ TUBV-015E TUBV-015V 2 TUBV-020E TUBV-020V 3 TUBV-030E TUBV-030V 4 TUBV-040E TUBV-040V Description: Material: PVC, CPVC, Clear PVC, PP, PVDF : 1/2'' - 4''; 20mm - 110mm; DN15 - DN100 Standard: ANSI, DIN, JIS, CNS Joint End: Socket, Threaded (NPT, PT, BSPF), Fusion, Welding Seat - PTFE, TPV ; ORING - EPDM, VITON Working Pressure: 150 PSI Operating Temperature: PVC(0~55 ); CPVC & PP(0~95 ) Handle colour : Red Valve body colour : PVC (dark gray), CPVC (light grey), PP (light yellow), Clear PVC (transparent), PVDF (ivory) 17

20 Valves & Actuation Georg Fischer 3-Way Ball Valves Socket Thread PVC HORIZONTAL with EPDM ½ ¾ ¼ ½ PVC HORIZONTAL with FPM ½ ¾ ¼ ½ Socket Thread PVC VERTICAL with EPDM ½ ¾ ¼ ½ PVC VERTICAL with FPM ½ ¾ ¼ ½

21 Valves & Actuation Georg Fischer Butterfly Valves EPDM FPM Type 567 PVC with Lever Handle ½ Type 567 PVC with Gear Operator ½

22 Valves & Actuation Sanking Butterfly Valves Sanking Lever Handle Butterfly Valve Features: Improved PP disc to enhance the performance New updated body to tightly connect with seals Materials meet drinking water standard 100% pure virgin material, CaCO3 free (Chalk) UV resistant powder added Can be assembled with Pneumatic/Electric Actuators EPDM FPM Type HLBV with Lever Handle 2 HLBV-020E HLBV-020V 2½ HLBV-025E HLBV-025V 3 HLBV-030E HLBV-030V 4 HLBV-040E HLBV-040V 5 HLBV-050E HLBV-050V 6 HLBV-060E HLBV-060V 8 HLBV-080E HLBV-080V Description: Material: PVC, CPVC, PP, PVDF : 1½" - 8''; 63mm - 225mm ; DN50 - DN200 Standard: ANSI, DIN, JIS Joint End: Flanges Working Pressure: 150 PSI Operating Temperature: PVC(0~55 ); CPVC & PP(0~95 ) Valve body colour : PVC (dark grey), CPVC (light grey), PP (light yellow) 20

23 Valves & Actuation Georg Fischer Diaphragm Valves EPDM FPM PVC Socket True Union ½ ¾ ¼ ½ Socket PVC/EPDM 3 PV300-GATE 4 PV400-GATE 21

24 Valves & Actuation Check Valves GF Spring Check Valve EPDM FPM PVC/EPDM ½ ¾ ¼ ½ Spears Ball Check Valve EPDM FPM PVC/EPDM ½ ¾ ¼ ½ ½ Praher Check Valves PVC/FPM Socket ½ PVS VT ¾ PVS VT 1 PVS VT 1¼ PVS VT 1½ PVS VT 2 PVS VT 2½ PVS VT 3 PVS VT 22

25 Valves & Actuation Primary Fluids Control Valves ECO Valve Back Pressure / Pressure Relief / Pressure Sustaining / Anti Syphon EPDM Seals FKM Seals PVC Body / CPVC Bonnet ½ ECO-50I-PVC-E ECO-50I-PVC-V ¾ ECO-75I-PVC-E ECO-75I-PVC-V 1 ECO-100I-PVC-E ECO-100I-PVC-V 1¼ ECO-125I-PVC-E ECO-125I-PVC-V 1½ ECO-150I-PVC-E ECO-150I-PVC-V 2 ECO-200I-PVC-E ECO-200I-PVC-V Back Pressure / Pressure Sustaining / Anti Syphon: ECO Valve is a diaphragm style two port back pressure/pressure sustaining valve designed to provide and control a continuous pressure on the discharge side of a positive discharge style pump, such as metering pumps. ECO Valve assists with the proper seating of the valve check assembly and accurate filling of the pump housing chamber for a more efficient and accurate running pump. Pressure Relief: ECO Valve is also designed to be used as a two port off line pressure relief valve to help protect the discharge side of positive displacement pumps from system failure due to over pressure caused by a blockage or accidental valve closure on the downstream side of the pump. Available in PVC, CPVC, PVDF, polypropylene and 316L stainless steel Long life single sealing diaphragm (laminated PTFE, Viton, EPDM or PVC) Field adjustable pressure setting PSIG ( kpa) CPVC bonnet for higher temperatures and chemical resistance rating No moving parts in wetted chamber; superior choice for "dirty" fluid applications High flow capacity with lower pressure drop s 1/4" to 4" (8 DN to 100 DN) Configured for gauge port in either flow direction (on upstream side of valve) Available in 10 different connection configuration: threaded, socket, union and flanged Metering Equipment If you need anything to do with Metering ask us about Primary Fluids range of: Calibration Cylinders Pulsation Dampeners Injection Quills Corporation Stops Degassing Valves Need Metering Pumps? can supply the following brands Ask us for a quote on your next project 23

26 Strainers & Filters Praher In-Line Strainers True Union Strainer PVC/EPDM ½ PVS ¾ PVS PVS ¼ PVS ½ PVS PVS ½ PVS PVS Hayward Basket Strainer Hayward SB Series - Eastar EPDM FPM PVC Socket True Union 2 SBC200STE SBC200ST 4 SBC400SE SBC400S 24

27 Tank Adaptors & Schedule 40 Grey Fittings Spears Tank Adaptors EPDM FPM PVC Socket True Union ½ 8170E V-005 ¾ 8170E V E V-010 1¼ 8170E V-012 1½ 8170E V E V-020 Hose Tail Soc x Adaptor Socket PVC ½ G ¾ G G Hose Tail MPT x Adaptor Socket PVC ½ G ¾ G G Hose Tail Spig x Adaptor Socket PVC ½ G ¾ G G Hose Tail FPT x Adaptor PVC 25 Socket ½ SR ¾ SR SR EPDM Expansion Joints FPM PVC/EPDM ½ x x12 ¾ x x x x12 1½ x x x x x x x x x x x x12 Female Adaptor Soc x FBSP Socket Sch40 PVC G 1¼ G 1½ G G Male Adaptor Soc x MBSP Socket Sch40 PVC G 1¼ G 1½ G G Male Adaptor Spig x MBSP Socket Sch40 PVC G 1¼ G 1½ G G Female Adaptor Spig x FBSP Socket Sch40 PVC G 1½ G G

28 Valves & Actuation Primary Fluids Control Valves